Dual Screen Video Processor
with Two DVI Inputs
Model #: DVI-SPLITPRO-2B
© 2010 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product descriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims any express or implied warranty, relating to its products
including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.
www.avenview.com
1
Table of Contents
Section 1: Getting Started ...................................................................................................................... 3
1.1
Important Safeguards ............................................................................................................ 3
1.2
Safety Instructions ................................................................................................................. 3
1.3
Regulatory Notices Federal Communications Commission (FCC) ......................................... 4
1.4
Introduction ........................................................................................................................... 4
1.5
Package Contents................................................................................................................... 6
1.6
Before Installation.................................................................................................................. 6
1.7
Panel Description ................................................................................................................... 7
1.7.1 DVI-SPLITPRO-2B Rear Panel ................................................................................................. 7
1.7.2 DVI-SPLITPRO-2B I/O Connectors.......................................................................................... 8
1.8
Installation ............................................................................................................................. 9
1.9
IR Remote Control................................................................................................................ 10
1.10
On Screen Display Menu ...................................................................................................... 11
1.11
System Requirements .......................................................................................................... 13
1.12
Software Connection ........................................................................................................... 13
1.13
Software Operation ............................................................................................................. 15
1.14
Control Setting Dialog .......................................................................................................... 18
Section 2: Specifications....................................................................................................................... 22
2.1
Supported Resolutions......................................................................................................... 23
2.1.1
DVI / Component / VGA ............................................................................................... 23
2.1.2
VGA............................................................................................................................... 23
2.1.3
DVI-OUT........................................................................................................................ 24
2.2
General Troubleshooting ..................................................................................................... 24
www.avenview.com
2
Section 1: Getting Started
1.1
Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover


Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
 Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized
product modification, or failure to follow instructions supplied with the product.
 Repair or attempted repair by anyone not authorized by us.
 Any damage of the product due to shipment.
 Removal or installation of the product.
 Causes external to the product, such as electric power fluctuation or failure.
 Use of supplies or parts not meeting our specifications.
 Normal wear and tear.
 Any other causes which does not relate to a product defect.

Removal, installation, and set-up service charges.
1.2
Safety Instructions
The Avenview DVI-SPLITPRO-2B Dual Image Video Processor has been tested for conformance to safety
regulations and requirements, and has been certified for international use. However, like all electronic
equipment’s, the DVI-SPLITPRO-2B should be used with care. Read the following safety instructions to protect
yourself from possible injury and to minimize the risk of damage to the unit.




Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards


Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.


www.avenview.com
3
1.3
Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
1.4
Introduction
The DVI-SPLITPRO-2B Dual Screen Video Processor is an advanced video processor for multimedia
presentations. It is an ideal solution for applications where up to four video signals must be displayed on a
single display. It supports up to 4 video inputs, of which 2 can be outputted simultaneously with the desired
display layout through software control. The advanced video processor allows you to manipulate output
images, wherever positions and whatever sizes you want for viewing two computers or two video signals or a
combination.
The embedded scalar converts signals from input sources to match the native resolution of monitors, flat
panel displays, projectors as well as user-selectable output settings up to WUXGA (1920x1200). Dual outputs
are provided in both analog (VGA) and digital (DVI) format, one is connected to remote display and the other
is connected to on-site display for real time monitoring.
-
Four graphic (DVI / VGA) and two video (Component / Composite) Inputs, from 640x480 to 1920x1200,
(Only two can be used simultaneously)
-
Interlaced or progressive.
-
Dual outputs (DVI / VGA), 640x480 to 1920x1200.
-
PIP, PAB, Full screen modes and adjustable size& position through software.
-
Titles, borders and colored backgrounds.
-
Resize, position, flip, zoom& pan and blend output video.
-
Can be cascaded to obtain more images.
-
Image parameters and layouts are automatically saved in flash memory and can be recalled for later use.
-
Several Image parameters and layouts can be saved in computers and can be loaded for later use.
-
Video parameters adjustable (brightness, contrast, color temperature, etc.).
-
User-selectable output settings, up to 1920x1200.
-
Perfectly as a video screen splitter, a video converter and a video switcher.
-
Firmware upgradable for support of new features and technology enhancements.
-
IR control and software control through RS-232.
-
Portable size.
www.avenview.com
4
www.avenview.com
5
1.5
Package Contents
Before you start the installation of the converter, please check the package contents.
-
1.6




DVI-SPLITPRO-2B
DVI – DVI & VGA breakout Cable
VGA to Component breakout Cable
DVI to VGA Adapter
IR Remote Control
Software CD
DC 5V Power Adapter
User’s Manual
x1
x1
x1
x1
x1
x1
x1
x1
Before Installation
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it
may cause a fire.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
www.avenview.com
6
1.7
Panel Description
The DVI-SPLITPRO-2B has four inputs and accepts both graphics and video signals, which come from
computers and NTSC/PAL video sources respectively. There is a concept of main channel and sub channel for
this device. You can pick up two of the four inputs, one is for main channel and the other is for sub channel,
displays two of them simultaneously on the same screen.
1.7.1 DVI-SPLITPRO-2B Rear Panel
1
2
3
4
5
1.
DVI/VGA OUT
2.
DVI Input 2
3.
Composite Input
4.
DVI/VGA/COMPONENT Input 1
5.
DIP Switch
Factory Default: Turn on the DVI-SPLITPRO-2B then move both DIP Switches simultaneously up and down to
reset to Factory Default.
Input and Output ports support various resolutions from 640x480 – 1920x1200. For more details of the
supported resolution see the section below “Supported Resolution”.
www.avenview.com
7
1.7.2 DVI-SPLITPRO-2B I/O Connectors
Connectors
Input
Connectors
Video Source
DVI-IN 1
DVI-IN 2
Composite
Output
Connectors
DVI-I OUT
DVI
VGA
(DVI to VGA Adapter)
Component (YPbPr)
(DVI to VGA Adapter and VGA to Component
Adapter)
1 x DVI
1 x VGA
(DVI to DVI/VGA Y Cable)
1 x DVI
1 x Component
(DVI to DVI/VGA Y Cable and VGA to Component
Adapter)
VGA
Composite with a RCA Cable
Display
DVI Display
VGA Display
(DVI to VGA Adapter)
1 x DVI Display
1 x VGA Display
(DVI to DVI/VGA Y Cable)
www.avenview.com
8
1.8
Installation
To setup Avenview DV-SPLITPRO-2B follow these steps for connecting to a device:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
Ensure that DVI-SPLITPRO-2B and all other source devices are turned off
Connect a monitor, a projector or other displays that comes with DVI and/or VGA inputs by using 1
male-to-male DVI (VGA) cable to DVI-SPLITPRO-2B DVI output (you can connect 2 displays equipped
with DVI and VGA respectively by a DVI to DVI/VGA breakout cable
Plug in DVI to DVI/VGA breakout cable (DDVY01) to DVI-IN and plug in VGA to component breakout
cable to the VGA connector of the breakout cable.
Connect a monitor, projector, other displays that come with DVI / VGA inputs by using 1 male – male
DVI (VGA) cable to DVI-SPLITPRO-2B DVI output. (you can connect 2 displays equipped with DVI and
VGA respectively by DVI – DVI/VGA breakout cable)
Connect a device equipped with DVI output (such as PC) to the DVI connector of the breakout cable.
Connect a device equipped with component video output (YPbPr such as DVD player or camera) to
the 3-RCA jack.
Connect a device equipped with VGA output (such as laptop) to the VGA connector of
DVI-SPLITPRO-2B.
Connect a device equipped with composite video output to composite input of the DVI-SPLITPRO-2B.
Connect your computer with the DVI-SPLITPRO-2B by a 9-pin RS-232 cable and then install the
software.
Plug in power adapter cable into 5V DC power jack.
Switch on all devices connected and then switch on the video processor and then press “menu” to
display OSD menu.
Press down arrow key dropping down sub-menu to select the first channel (Main Channel)
video/graphic source.
Once the Main Channel has a video selected, press “exit” key to exit the sub-menu, and then move
right to the next item of OSD menu, which allows you to select the second channel (Sub Channel).
For detailed IR remote control operation, please refer to the On Screen Display menu and IR Remote
Control section.
www.avenview.com
9
1.9
IR Remote Control
DVI-SPLITPRO-2B ships with a compact remote control that allows for direct access to most commands used to
control the video processor.
1. Power
2. PIP Border
3. UP Button
4. Source
5. Reset
6. Right Button
7. Menu
8. Left Button
9. Logo
10. Exit
11. Down Button
12. Enter
13. Blank
14. Color
15. Auto
16. V Flip
17. H Flip
18. SWAP
19. PIP
20. Sub Pause
21. Main Pause
Power ON/OFF the device
Display the border of small image (under PIP
mode)
Move to the upper titles
Press to select a source for main channel
Factory Reset
Move to the right titles
Display OSD Menu
Move to the left titles
Display Logo
Move back to previous option or exit OSD Menu
Move to the lower titles
Press to drop down sub-menus or confirm the
selection
Blank out the screen
Automatically configure the main channel color
Automatically configure the man channel position
Flip vertically
Flip Horizontally
Swap between main channel and sub-channel
(only works in PIP or PAP mode)
Changes mode: Full Screen, PIP and PAP
Freeze sub-channel
Freeze main channel
www.avenview.com
10
1.10 On Screen Display Menu
www.avenview.com
11
Main Source:
Main Control:
Select an input source for the main channel (VGA / YPbPr, DVI, Composite, VGA)
Brightness (Slider)
Display
Image
Position
Color
PIP Control
Logo
Border
Sub Source:
Sub Control:
OSD Control:
Language
Selection:
Factory Reset:
Resolution
Selection:
Contrast (Slider)
Saturation (Slider)
Scaling (1:1, Fill, Aspect, Panorama)
Adaptive De-interlacing (Button: Off, Level 1,
Level 2, Level 3)
Noise Reduction (Button: Off, Low, Med, High)
Zoom(Button: In, Out)
Hue (Slider)
Flesh-tone (Button: Off, Weak, Soft,
Strong)
Angle Filtering (Button: Off, On)
Film Mode Detect (Button: Off, On)
Sharpness (Slider)
Zoom Vertical Pan (Button: Down, Up)
Zoom Horizontal Pan (Button: Left, Right)
Vertical (Slider)
Horizontal (Slider)
sRGB (Button: Off, On Cl.BA)
Red (Slider)
Gamma Correction (Button: Off, 2.2, 2.4)
Green (Slider)
Color Temperature (Button: User, 6500K,
Blue (Slider)
9300K)
PIP Mode (Off, Single, PAP)
Vertical (Slider)
PIP Size (Small, Medium, Large)
Horizontal (Slider)
Blend (Slider)
(Off, On)
(Off, On)
Red (Slider)
Green (Slider)
Blue (Slider)
Width (Slider)
Select an input source for sub-channel (VGA/component, DVI, composite, VGA)
The same as Main Control
Vertical (Slider)
Horizontal (Slider)
Time out (Slider)
OSD Zoom (On, Off)
Blend (Slider)
English and Traditional Chinese
Reset the device to default
Press Down Button to select an output resolution and then press enter to confirm that
selection
800×600 @60Hz, 1280×768 @60Hz, 1440×900 @60Hz, 1920×1080 @50Hz
1024×768 @60Hz, 1280×1024 @50Hz, 1400×1050 @50Hz, 1920×1080 @60Hz
1152×864 @75Hz, 1280×1024 @60Hz, 1400×1050 @60Hz, 1920×1200 @50Hz
1280×720 @50Hz, 1366×768 @60Hz, 1600×1200 @60Hz, 1920×1200 @60Hz
1280×720 @60Hz
www.avenview.com
12
1.11 System Requirements
1.
2.
3.
The DVI-SPLITPRO-2B provides a software control program which runs under Microsoft Windows 98,
2000, XP, VISTA through the interface of RS-232 serial control.
Before you click on the icon of the software, make sure you have secured the connection between
your computer COM port and the DVI-SPLITPRO-2B.
The DVI-SPLITPRO-2B provides software control. To make sure all information shown in the software
is synchronized with those in the device, please click “Update” button to acquire the latest data from
the DVI-SPLITPRO-2B after you press any key on the remote control.
1.12 Software Connection
1.
2.
Power up the DVI-SPLITPRO-2B and you can see both Red and Green LEDs on the front panel blink.
Ensure that Serial RS232 connection is secure.
The first step after running the software is to automatically detect if the device responses correctly
through RS-232 port. The process takes 5-15 seconds. If the device is not connected, a warning
window will show up. First of all, choose the correct COM port from the Com Port selection list. Then,
click on the linkage button to open the COM port. If the specified COM port is not available, the
“Device is not ready. Do you want to try again?” error message will pop up. Please check the
availability of COM Port. After the COM port is accurately established, please click on status update
button.
If” device is not ready” error pops up then:
Ensure that DVI-SPLITPRO-2B is powered on.
Please ensure that serial cable (RS232) is connected properly and available serial
port is free to be used by DVI-SPLITPRO-2B
3.
If the serial connection is established, you will see a Windows as shown below:
www.avenview.com
13
4.
While you move the mouse’s cursor near the borders, in either red or blue, the icon of the cursor will
change as the figure below.
www.avenview.com
14
1.13 Software Operation
File
Connect
Save Settings
Load Settings
IR Control
Auto Sleep
Device ID
Factor Reset
Exit
Synchronizes the status of the DVI-SPLITPRO-2B with that of the software, especially after
IR commands sent.
Save current user preferred settings such as the positions and sizes of the videos, the width
or color of border etc. into your favorite setting files. (See Figure Save Setting below)
Load the favorite settings from the previously saved file
Enable or Disable IR Remote Control function
Enable or Disable auto sleep function if there is no video signal detected in the main
channel
Define Device ID of each DVI-SPLITPRO-2B especially when multiple devices are cascaded.
(See Device ID Setting below)
Restore all system settings to factory default
Quit the software
Save Setting
1.

Assign an ID for the connect DVI-SPLITPRO-2B, Type a digit from 1 –
255 and then click on “Write”.
2. Read the ID of the connected DVI-SPLITPRO-2B; Click “Read” and the
Device ID will show up under “ID Number”.
3. Super Control: All devices cascaded will receive and respond the same
way when you are operating the Control Software.
4. Single Device Control: Remote the check beside the “Super Control”
and type a number that represent a specific DVI-SPLITPRO-2B and
then click “Apply. Exit the “Device ID Setting” and click “Connect”.
*Please note that if only one device is being used, you don’t need to
change Device ID.
www.avenview.com
15
Background
Resolution
Layout
H-Flip
V-Flip
SWAP
Color
Custom Size 1-3
Change the output resolution
The preset layout for main & sub channels
Horizontally flip the output video
Vertically flip the output video
Swap the main the sub channel
The background color selection
Save or read main/sub channel size, position, visible and Layer.
Main
Input Source
Visible
Border
Label
Layer
Pause
Full Screen
Color Balance
Auto Config.
Select a video/graphic input of the main channel
Display the main channel or not
Display the main channel’s border
Display the main channel’s label. Users can define the content of the label
This will make the main channel overlays the sub channel
Freeze the display of the main channel
Display the main channel full screen
Automatically do the color balance while the main channel’s input is from VGA/Component
Automatically do the auto adjustment while the main channel’s input is from
VGA/Component
www.avenview.com
16
Sub
Input Source
Visible
Border
Label
Layer
Pause
Select a video/graphic input of the sub-channel
Display the Sub-Channel or not
Display the sub-channel’s border
Display the sub-channel’s label. Users can define the content of the label
This will make the sub-channel overlays the main channel
Freeze the display of the sub-channel
www.avenview.com
17
1.14 Control Setting Dialog
Border
Select main or sub channel for further settings
Clear All
Apply
Border Color
Border Width
Border Type
Clear all OSD items
Apply the settings
Setup border’s color by clicking on “Color Settings”
Input border’s width
The placemat of border has three types:
Inside means the added border is fully inside the video.
Outside means the added border is completely outside the video and this added border can overlay
the other video input.
Middle means the border half inside the video and half outside the video
Select the color of the label by clicking on “Color Settings”
When selected the label on the screen for each channel will display its corresponding input channel
type.
When not selected the user can input the desired string to be displayed
Text Color
Text Auto
Duty Cycle
Frequency
*PAP Mode Only
Enables blinking of OSD borders and labels
Select how fast OSD border and labels blink
*Only 15 English characters can be display
www.avenview.com
18
Image
1.
Choose the scaling type for the main channel
at fully screen display
2.
While Blend is selected, users can use the
slider to control the control the degree of
blending
Color
1.
Select the main or sub channels
2.
Reset: Restore all the setting on this page
back to their factory default settings.
www.avenview.com
19
Zoom
1.
Select the main or sub channel
2.
Default: Restore the selected channel
without zoom effect
3.
Slider controls the ratio of zoom.
4.
The workplace for controlling the displayed
area after zooming the selected video.
Pattern
1.
While the “Pattern Model” is chosen, the
output will display the selected pattern.
While unselecting this item, the output
display works normally.
2.
The organ border indicates which pattern is
currently selected. Users can choose one of
the provided patterns by moving cursor
and clicking at the desired one
3.
Users can define the pattern’s color by
changing Red, Green and Blue values
www.avenview.com
20
HS/VS Delay
1.
Select the main or sub channel
2.
The fine movement of the selected channel
1.
Save: Save the read back EDID Content in
PC
2.
Setting: Automatically setup the output
resolution according to the content of EDID
Zoom
*This setting is according to the content of EDID,
and the optimum resolution for the monitor might
be different because of limited information of the
acquired EDID info.
www.avenview.com
21
Section 2: Specifications
Item
Unit
Description
Dual Output Support
Video Bandwidth
Supported Resolutions
Audio Support
Control
Embedded Video Mixer
Ability to Cascade
Input TMDS Signal
ESD Protection
Input
Output
DVI Connector Type
VGA Connector Type
RS232 Connector
RCA Connector
RJ45 Connector
IR Remote Control
Dimensions
Power Supply
Power Consumption
Operating Temperature
Storage Temperature
Relative Humidity
Description
DVI-SPLITPRO-2B
Dual Screen Video Image Processor
Yes (DVI OR VGA)
DVI Single Link - 4.95Gbps
VGA - 165 MHz
Component - 30 MHz
Composite – 13.5 MHz
480i / 480p / 720p / 1080i / 1080p (60) / 1920x1200@75 / 1600x1200@60
No
RS232 & IR
Yes
Yes
1.2 Volts (peak – peak)
Human body model - ± 15kV (air gap discharge) & ±8kV (contact discharge
2 x DVI
1 x Composite
1 x RS232
1 x DVI
(VGA through DVI to VGA Adapter)
DVI-I (29-Pin female)
HD-15 (15-pin D-sub female)
DE-9 (9-pin D-sub female)
75Ω
WE/SS 8P8C with 2 LED indicators
Yes
7.1" x 4” x 0.9" (L x W x H)
5V 4A DC
10 Watts (max)
0~40°C [32~104°F]
-20~60°C [-4~140°F]
20~90% RH [no condensation]
www.avenview.com
22
2.1
Supported Resolutions
2.1.1
DVI / Component / VGA
Supported Mode
Resolution
Supported Mode
Resolution
NTSC/480i/525i
PAL/576i/625i
480p/525p
480p (16:9)
576p/625p
(HDTV) 720p
(HDTV) 720p
(HDTV) 1080i
(HDTV) 1080i
(HDTV) 1080p
VESA
VESA
VESA
IBM
IBM
IBM
IBM
VESA
MAC
VESA
VESA
VESA
VESA
VESA
VESA
VESA
VESA
720x240 @60Hz
720x288 @50Hz
720x483 @60Hz
960x483 @60Hz
720x756 @50Hz
1280x720 @50Hz
1280x720 @60Hz
1920x1080 @50Hz
1920x1080 @60Hz
1920x1080 @30Hz
720x400 @85Hz
640x350 @85Hz
640x400 @85Hz
720x400 @70Hz
720x350 @70Hz
640x350 @70Hz
640x400 @70Hz
640x480 @60Hz
640x480 @67Hz
640x480 @72Hz
640x480 @75Hz
640x480 @85Hz
800x600 @56Hz
800x600 @60Hz
800x600 @72Hz
800x600 @75Hz
800x600 @85Hz
MAC
VESA
MAC
VESA
IBM
VESA
MAC
VESA
VESA
MAC
SUN
SUN
VESA
VESA
VESA
HP
IBM
HP
VESA
SUN
VESA
VESA
832x624 @75Hz
1024x768 @60Hz
1024x768 @60Hz
1024x768 @70Hz
1024x768 @72Hz
1024x768 @75Hz
1024x768 @75Hz
1024x768 @85Hz
1152x864 @75Hz
1152x870 @75Hz
1152x900 @66Hz
1152x900 @76Hz
1280x960 @60Hz
1280x960 @85Hz
1280x1024 @60Hz
1280x1024 @60Hz
1280x1024 @67Hz
1280x1024 @72Hz
1280x1024 @75Hz
1280x1024 @76Hz
1600x1200 @60Hz
1920x1200 @60Hz
2.1.2
VGA
Supported Mode
Resolution
VESA
VESA
VESA
VESA
VESA
VESA
640x480 @60Hz
800x600 @60Hz
1024x768 @60Hz
1280x1024 @60Hz
1600x1200 @60Hz
1920x1200 @60Hz
www.avenview.com
23
2.1.3
DVI-OUT
Supported Mode
Resolution
Supported Mode
(HDTV) 720p
1280x720 @50Hz
VESA
1366x768 @60Hz
(HDTV) 720p
1280x720 @60Hz
VESA
1400x1050 @60Hz
(HDTV) 1080p
1920x1080 @60Hz
VESA
1400x1050 @50Hz
VESA
640x480 @60Hz
VESA
1152x864 @75Hz
VESA
800x600 @60Hz
VESA
1600x1200 @60Hz
VESA
1024x768 @60Hz
VESA
1920x1200 @50Hz
VESA
1152x864 @75Hz
VESA
1920x1200 @60Hz
VESA
1280x1024 @60Hz
2.2
Resolution
General Troubleshooting
Problem
No Power
Possible Solution



No or Distorted Image


Poor Quality


Image Position Shifted
Auto color configuration only works at VGA and Component inputs

Wrong Color
Ensure that DVI-SPLITPRO-2B is plugged in
If you are recovering from power outage, accidentally unplug the
adapter or other power surge conditions, leave the device off for
a while and then power it on again.
Make sure all cables are in good working condition and properly
connected to the DVI-SPLITPRO-2B and displays.
Configure the output video resolution so that it doesn’t excess
the native resolution of the display. ( in this case, the message of
“out of range” is usually showed on your screen)
We suggest that don’t use T-connectors to split your video source
into to images displayed on two different screens. That will lower
output video quality. Use a distribution amplifier instead of
T-connectors.
Make sure the video source is not compressed and maintains the
highest native resolution.
Press “Auto” key on the remote control
Press “Color Balance” key for auto configuration.
Auto color configuration only works at VGA and Component inputs.
www.avenview.com
24
Notice
1.
If the DVI or HDMI device requires the EDID information, please use EDID Reader/Writer to
retrieve and provide DVI/HDMI EDID information.
2.
All HDMI over CAT5 transmission distances are measured using Belden 1583A CAT5e 125MHz
LAN cable and ASTRODESIGN Video Signal Generator VG-859C.3
3.
The transmission length is largely affected by the type of LAN cables, the type of HDMI sources,
and the type of HDMI display. The testing result shows solid LAN cables (usually in bulk cable
300m or 1000ft form) can transmit a lot longer signals than stranded LAN cables (usually in
patch cord form). Shielded STP cables are better suit than unshielded UTP cables. A solid UTP
CAT5e cable shows longer transmission length than stranded STP CAT6 cable. For long extension
users, solid LAN cables are your only choice.
4.
EIA/TIA-568-B termination (T568B) for LAN cables is recommended for better performance.
5.
To reduce the interference among the unshielded twisted pairs of wires in LAN cable, you can use
shielded LAN cables to improve EMI problems, which is worsen in long transmission.
6.
Because the quality of the LAN cables has the major effects in how long transmission distance
will be made and how good is the received display, the actual transmission length is subject to
your LAN cables. For resolution greater than 1080i or 1280x1024, a CAT6 cable is recommended.
7.
If your HDMI display has multiple HDMI inputs, it is found that the first HDMI input
[HDMI input #1] generally can produce better transmission performance among all HDMI inputs.
www.avenview.com
25
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the
operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of
Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of
anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the
Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability,
function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and
non-infringement.
www.avenview.com
26