reviewed for validity of design criteria only

PROJECT NAME:
OE PROJECT NO.:
Shelby CS High School
J20100329.000
SUBMITTAL NO:
Cisco
MANUFACTURER:
Network Equipment Data Sheets & Shop Drawing
DESCRIPTION:
SPEC SECTION:
Sub #006 2721001 Network
Equipment Data
Sheets 20130502
272100-1
DATE RECEIVED
5/2/13
DATE DUE
5/9/13
OSBORN DISTRIBUTION
Discipline
Reviewer
Review Complete Date
Action
Architectural:
Structural:
Civil:
Mechanical:
Electrical:
1100 Superior Ave., #300
441 Wolf Ledges Pkwy., #300
Cleveland, OH 44114
Akron, OH 44311
t: 216-861-2020
t: 330-535-3132
f: 216-861 3329
f: 330-535-3195
X
Technology
AMW
Other:
1.
“px” in the check box indicates the Primary Reviewer; “x” in the check box
indicates additional Reviewer(s).
2.
The Primary Reviewer should review the submittal first.
3.
The Primary Reviewer is responsible for coordinating with the other
disciplines.
osborn-eng.com
This information is only for the general conformance with the design
concept and the information given in the Construction Documents.
Comments made on the shop drawings during this review do not relieve
the contractor from compliance with the requirements of the plans and
specifications and applicable laws, codes and regulations. Review of a
specific item shall not include review of an assembly of which the item is a
component. The Contractor is responsible for: dimensions to be confirmed
and correlated at the job site; information that pertains solely to the
fabrication processes or to the means, methods, techniques, sequences
and procedures of construction; coordination of the Work with that of all
other trades and performing Work in a safe and satisfactory matter.
REVIEWED FOR VALIDITY OF DESIGN
CRITERIA ONLY
REVIEWED (REV):
FURNISH AS NOTED (FN):
REVISE AND RESUBMIT (RR):
REJECTED (REJ):
SUBMIT SPECIFIED ITEM:
SUBMITTAL NOT REQUIRED
AND NOT REVIEWED:
REVIEWED BY: AWM
DATE: 6/10/2013
NO EXCEPTION TAKEN:
REVISE AND RESUBMIT
AS NOTED:
REVIEWED BY:
DATE:
Comments:
1. Convert any PoE line cards in the core 4500 to stackable PoE switches matching the edge switch specification.
2. Verify that the UPS’s being provided meet the required runtime specified.
3. Please clarify how a 4000W power supply can be backed up by either a 2200 or 3000 VA UPS.
4. Verify quantity of single mode SFP’s are being provided. Hold on procurement of these as this quantity will be reducing.
Page 1 of 1
Submittal Review Form - Standard
Submittal Stamp Page
PROJECT:
Shelby High School
CM / AE:
Barton Malow Company, MKC Associates & Obsorn Engineering
CONTRACTOR:
Zenith Systems LLC
Submittal Type Attached:
Architectural
X
Structural, Mechanical, Electrical
SUBMITTAL NO:
Shop Drawings
Samples
DATE:
1
ITEM(S): Network Equipment Data Sheets & Shop Drawing
SPECIFICATION SECTION(S):
QUANTITY:
27 21 00
CONTRACTOR STAMP
By Stacie Steele at 1:54 pm, May 01, 2013
CM STAMP
A/E STAMP
5/1/2013
1
PROJECT SUBMITTALS
Shelby Schools
High School Technology
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
SEC /
ITEM
27 21 00
2.2 A
27 21 00
2.2 A
27 21 00
2.2 A 16 a
27 21 00
2.2 A 16 a
27 21 00
2.2 A 16 a
27 21 00
2.2 A
27 21 00
2.2 A
27 21 00
2.2 B
27 21 00
2.2 C
27 21 00
2.2 C
27 21 00
2.3 A
27 21 00
2.3 D
27 21 00
2.3 D
27 21 00
2.3 D
27 21 00
2.3 D
27 21 00
2.5
27 21 00
2.5
27 21 00
2.5
27 21 00
2.5
27 21 00
2.6
27 21 00
2.6
DESCRIPTION
MNFG
PART NUMBER
Core Switch Chassis
Cisco
WS‐C4510R+E=
Core Supervisor Module
Cisco
WS‐X45‐SUP7‐E
Power Supplies
Cisco
PWR‐C45‐4200ACV=
24 Port SFP Line Card
Cisco
WS‐X4624‐SFP‐E=
12 Port SFP Line Card
Cisco
WS‐X4612‐SFP‐E=
48 Port Copper 10/100/1000 POE Line Card
Cisco
WS‐X4648‐RJ45V+E=
48 Port Copper 10/100/1000 Line Card
Cisco
WS‐X4648‐RJ45‐E=
48 Port 10/100/1000 non‐POE Edge Switch
Cisco
WS‐C2960S‐48TS‐L
48 Port 10/100/1000 POE Edge Switch (370W)
Cisco
WS‐C2960S‐48LPS‐L
24 Port 10/100/1000 POE Edge Switch (370W)
Cisco
WS‐C2960S‐24PS‐L
Wireless Access Points
Cisco
AIR‐LAP1142N‐A‐K9
Wireless Controller
Cisco
AIR‐CT5508‐100‐K9
Wireless Control System
Dell
R‐320
WCS Licenses
Cisco
WCS‐PLUS‐100
Mobility Services Engine
Cisco
AIR‐MSE‐3310‐K9
SMX3000RMLV2U + Please see associated closets below
SMX120RMBP2U 3000 UPS Unit with Battery Pack
APC
3000 UPS Unit
APC
SMT3000RM2U 2200 UPS Unit
APC
SMT2200RM2U
UPS Network Management Card
APC
AP‐9630
Power Distribution Unit
APC
AP7832 Power Distribution Unit
APC
AP7830
27 21 00
Fiber SFP Module
Cisco
GLC‐SX‐MM
27 21 00
Copper SFP Module
Cisco
GLC‐T
27 21 00
Network Shop Drawing
Zenith
‐
16
17
UPS Units
ER 1‐11: SMX3000RMLV2U + SMX120RMBP2U
ER 1‐11: SMT3000RM2U
TR 1‐11: SMT2200RM2U
TR 1‐12: SMT2200RM2U
*UPS units based on calculations as specified
Power Distribution Units
SMX3000RMLV2U + SMX120RMBP2U: AP7832
SMT3000RM2U: AP7832
SMT2200RM2U: AP7830
*PDUs are based on compatibility with UPS units calculated & provided per specifications
27 21 00
NOTES
Please see associated closets below
Please see associated closets below
works with all submitted UPS units
Please see associated closets below
Please see associated closets below
ITEM 1
Data Sheet
Cisco Catalyst 4500E Series Chassis
High Performance, Mobile and Secure User Experience
Overview
®
®
The Cisco Catalyst 4500 Series Switches enable borderless networks, providing high performance, mobile, and
secure user experience through Layer 2-4 switching investments. It enables security, mobility, application
performance, video, and energy savings over an infrastructure that supports resiliency, virtualization, and
automation. Cisco Catalyst 4500 Series Switches provide borderless performance, scalability, and services with
reduced total cost of ownership and superior investment protection.
Cisco Catalyst 4500 (Figure 1) has a centralized forwarding architecture that enables collaboration, virtualization,
and operational manageability through simplified operations. With forward and backward compatibility spanning
multiple generations, the new Cisco Catalyst 4500E Series provides exceptional investment protection and
deployment flexibility to meet the evolving needs of organizations of all sizes. The Cisco Catalyst 4500E Series
platform has 10 Gigabit Ethernet (GE) uplinks and supports PoEP, enabling the customers to future proof their
network.
E-Series chassis come in four different form factors: 3-slot (4503-E), 6-slot (4506-E), 7-slot (4507R+E/4507R-E), and
10-slot (4510R+E/4510R-E). 4503-E, 4506-E, 4507R+E, and 4510R+E chassis are extremely flexible and support
either 6 Gbps, 24 Gbps, or 48Gbps per line-card slot. 4507R-E and 4510R-E chassis are limited to 6 Gbps and 24
Gbps per line-card slot. Integrated resiliency in the Cisco Catalyst 4500E Series includes 1+1 supervisor engine
redundancy (10-slot and 7-slot only), redundant fans, software-based fault tolerance, and 1+1 power supply
redundancy. Integrated resiliency in both hardware and software minimizes network downtime, helping to ensure
workforce productivity, profitability, and customer success.
Figure 1.
Cisco Catalyst 4500E Series
The Cisco Catalyst 4500E Series extends control to the network edge with intelligent network services, including
sophisticated quality of service (QoS), predictable performance, advanced security, comprehensive management,
and integrated resiliency. Scalability of these intelligent network services is made possible with dedicated,
specialized resources known as ternary content-addressable memory (TCAM). Ample TCAM resources (up to
384,000 entries) enable “high feature capacity,” which provides wire-speed routing/switching performance
independent of provisioning of services such as QoS and security.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 12
Data Sheet
Cisco Catalyst 4500E Series Chassis
The Cisco Catalyst 4500E Series offers four chassis options and eight supervisor engine options (Table 1). It
provides a common architecture that can scale up to 388 ports. The Cisco Catalyst WS-C4507R+E, WS-C4510R+E,
WS-C4507R-E, and WS-C4510RE offer high availability by supporting 1+1 redundant supervisor engines with
subsecond failover time and full-image In-Service Software Upgrades (ISSUs). Nonstop forwarding with Stateful
Switchover (NSF/SSO) and ISSU help ensure continuous packet forwarding during supervisor engine switchover to
help ensure high availability for collaboration applications and voice over IP (VoIP). Using the same line cards as the
widely deployed Cisco Catalyst 4000 Series Switches and classic Cisco Catalyst 4500 Series Switches, the Cisco
Catalyst 4500E Series furthers Cisco’s commitment to affordable enterprise and branch scalability.
Table 1.
Cisco Catalyst 4500E Series Chassis Features
Feature
Cisco Catalyst
WS-C4503-E Chassis
Cisco Catalyst
WS-C4506-E Chassis
Cisco Catalyst
WS-C4507R+E Chassis
Cisco Catalyst
WS-C4510R+E Chassis
Total number of slots
3
6
7
10
Line-card slots
2
Supervisor engine slots
1
1
2
2
Dedicated supervisor
engine slot numbers
1
1
3 and 4
5 and 6
Supervisor engine
redundancy
No
No
Yes
Yes (Supervisor V-10GE, 6E and 7-E)
Supervisor engines
supported
Supervisor 7-E
Supervisor 7-E
Supervisor 7-E
Supervisor 7-E
Supervisor 6-E
Supervisor 6-E
Supervisor 6-E
Supervisor 6-E
Supervisor 6L-E
Supervisor 6L-E
Supervisor 6L-E
Supervisor V-10GE
Supervisor V-10GE
Supervisor V-10GE
Supervisor V-10GE
Bandwidth scalability per
line-card slot
Up to 48 Gbps on all slots
Up to 48 Gbps on all slots
Up to 48 Gbps on all slots
Number of power supply
bays
2
2
2
2
AC input power
Yes
Yes
Yes
Yes
DC Input power
Yes
Yes
Yes
Yes
Integrated Power over
Ethernet
Yes
Yes
Yes
Yes
Minimum number of
power supplies
1
1
1
1
5
1
Power supplies supported
5
1
8
2
3
5
4
5
Up to 48 Gbps on all slots
● 1000W AC
● 1400W AC
● 1300W ACV
● 1000W AC
● 1400W AC
● 1300W ACV
● 1000W AC
● 1400W AC
● 1300W ACV
● 1400W AC
● 2800W ACV
● 4200W ACV
● 2800W ACV
● 4200W ACV
● 6000W ACV
● 2800W ACV
● 4200W ACV
● 6000W ACV
● 2800W ACV
● 4200W ACV
● 6000W ACV
● 6000W ACV
● 1400W DC (triple input)
● 1400W-DC-P
● 1400W DC (triple input)
● 1400W-DC-P
● 1400W DC (triple input)
● 1400W-DC-P
● 1400W DC (triple input)
● 1400W-DC-P
Number of fan-tray bays
1
1
1
1
Location of 19-inch rack
mount
Front
Front
Front
Front
Location of 23-inch rack
mount
Front (option)
Front (option)
Front (option)
Front (option)
1
Slot 1 is reserved for supervisor engine only; slots 2 and higher are reserved for line cards.
Slots 3 and 4 are reserved for supervisor engines only in Cisco Catalyst 4507R-E and 4507R+E; slots 1-2 and 5-7 are reserved
for line cards.
3
Slots 5 and 6 are reserved for supervisor engines only in Cisco Catalyst 4510R-E and 4510R+E; slots 1-4 and 7-10 are reserved
for line cards.
4
6 Gbps only on slots 8-10.
5
WS-C4507R-E and WS-C4510R-E chassis support up to 24G per line-card slot when used with Sup6-E.
2
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 12
Data Sheet
Configuration Alternatives
The Cisco Catalyst 4500 Series offers a powerful and flexible network solution that can be built with eight supervisor
engine alternatives. Each provides a high-performance, centralized, shared-memory switch fabric, protecting your
line-card investment by supporting the addition of optional higher layer engines (Table 2).
Table 2.
Cisco Catalyst 4500E Series Supervisor Engine Support
Feature
Cisco Catalyst 4500
Series Supervisor V-10GE
Cisco Catalyst 4500
Series Supervisor 6L-E
Cisco Catalyst 4500
Series Supervisor 6-E
Cisco Catalyst 4500
Series Supervisor 7-E
Cisco Catalyst WS-C4503E Chassis
6Gbps/Slot
24Gbps/Slot
24Gbps/Slot
48Gbps/Slot
Cisco Catalyst WS-C4506E Chassis
6Gbps/Slot
24Gbps/Slot
24Gbps/Slot
48Gbps/Slot
Cisco Catalyst WSC4507R+E Chassis
6Gbps/Slot
24Gbps/Slot
24Gbps/Slot
48Gbps/Slot
Cisco Catalyst WSC4510R+E Chassis
6Gbps/Slot
Not supported
24Gbps/Slot
48Gbps/Slot
Cisco Catalyst WSC4507R-E Chassis
6Gbps/Slot
24Gbps/Slot
24Gbps/Slot
24Gbps/slot
Cisco Catalyst WSC4510R-E Chassis
6Gbps/Slot
Not supported
24Gbps/Slot
24Gbps/slot
The Cisco Catalyst 4500 Series has flexible interface types and port densities that allow network configurations to be
mixed and matched to meet the specific needs of campus networks (Table 3).
Table 3.
Cisco Catalyst 4500 Series Port Densities
Cisco Catalyst 4500 Series Switching Modules
Number of
Interfaces
Supported per
Line Card
Cisco Catalyst
4503-E
Cisco Catalyst
4506-E
Cisco Catalyst
4507R+E
Cisco Catalyst
4510R+E
Switched 10/100 Fast Ethernet (RJ-45)
48
96
240
240
384
Switched 10/100 Fast Ethernet (RJ-45) with IEEE
802.3af at Power over Ethernet (PoE/PoEP)
48
96
240
240
384
Switched 100 FX Fast Ethernet (MT-RJ)
48
96
240
240
384
Switched 1000BASE-X (fiber)
6, 18, or 48
104
244
244
388
Switched 10/100/1000BASE-T Gigabit Ethernet
48
108
240
240
384
Switched 10/100/1000BASE-T Gigabit Ethernet with
IEEE 802.3af at PoE/PoEP
48
108
240
240
384
Switched 10 Gigabit Ethernet
6 or 12
28
64
64
6
6
100
Configuration Flexibility and Modular Superiority
Cisco Catalyst 4500 Series line cards can be mixed and matched to suit numerous LAN access, server connectivity,
SMB, or branch-office deployments. The Cisco Catalyst 4500 Series supports the following line cards, listed in Table
4 by part number.
Table 4.
Cisco Catalyst 4500 Series Line Cards
Product Number
Description
Cisco Catalyst 4500E Series Line Cards
WS-X4748-RJ45V+E
Cisco Catalyst 4500E Series 48-Port 802.3at PoEP 10/100/1000 (RJ-45)
WS-X4712-SFP+E
Cisco Catalyst 4500E Series 12-port 10 Gigabit Ethernet (SFP+)
WS-X4624-SFP-E
Cisco Catalyst 4500E Series 24-port GE (SFP)
WS-X4612-SFP-E
Cisco Catalyst 4500E Series 12-port GE (SFP)
6
WS-C4507R-E and WS-C4510R-E chassis support up to 34 switched 10 Gigabit Ethernet ports.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 12
Data Sheet
Product Number
Description
WS-X4648-RJ45V-E
Cisco Catalyst 4500E Series 48-Port PoE 10/100/1000(RJ45)
WS-X4648-RJ45V+E
Cisco Catalyst 4500E Series 48-Port Premium PoE 10/100/1000(RJ45)
WS-X4606-X2-E
Cisco Catalyst 4500E Series 6-Port 10GE (X2)
WS-X4648-RJ45-E
Cisco Catalyst 4500E Series 48-Port Data 10/100/1000(RJ45)
Cisco Catalyst 4500 Classic 10/100 Line Cards
WS-X4148-RJ
Cisco Catalyst 4500 10/100 Auto Module, 48-Port (RJ-45)
WS-X4248-RJ45V
Cisco Catalyst 4500 PoE 802.3af 10/100, 48-Port (RJ-45)
Cisco Catalyst 4500 Classic 10/100/1000 Line Cards
WS-X4548-GB-RJ45
Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45)
WS-X4548-RJ45V+
Cisco Catalyst 4500 48-Port 802.3af PoE and 802.3at PoEP 10/100/1000 (RJ-45)
WS-X4548-GB-RJ45V
Cisco Catalyst 4500 PoE IEEE 802.3af 10/100/1000, 48 Ports (RJ-45)
Cisco Catalyst 4500 Classic 100 BASE-X FE Line Cards
WS-X4248-FE-SFP
Cisco Catalyst 4500 Fast Ethernet Switching Module, 48-Port 100BASE-X (SFP)
Cisco Catalyst 4500 Classic 1000 BASE-X GE Line Cards
WS-X4306-GB
Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC)
WS-X4506-GB-T
Cisco Catalyst 4500 6-Port 10/100/1000 RJ-45 PoE IEEE 802.3af and 1000BASE-X
(SFP)
WS-X4418-GB
Cisco Catalyst 4500 Gigabit Ethernet Module, Server Switching 18 Ports (GBIC)
WS-X4448-GB-SFP
Cisco Catalyst 4500 Gigabit Ethernet Module, 48 Ports 1000X (SFP)
Table 5 lists the minimum software requirements for the Cisco Catalyst 4500 supervisor engines.
Table 5.
Cisco Catalyst Supervisor Engine Software Minimum Requirements
Chassis
Supervisor Engine
Minimum Software Requirement
Cisco WS-C4503-E and WS-C4506-E
Supervisor Engine V-10GE
Cisco IOS Software Release 12.2(37)SG
Supervisor Engine 6-E
Cisco IOS Software Release 12.2(40)SG
Supervisor Engine 6L-E
Cisco IOS Software Release 12.2(52)SG
Supervisor Engine 7-E
Cisco IOS XE Software Release 3.0(1)SG
Supervisor Engine V-10GE
Cisco IOS Software Release 12.2(54)SG
Supervisor Engine 6-E
Cisco IOS Software Release 12.2(54)SG
Supervisor Engine 6L-E
Cisco IOS Software Release 12.2(54)SG
Supervisor Engine 7-E
Cisco IOS XE Software Release 3.0(1)SG
Supervisor Engine V-10GE
Cisco IOS Software Release 12.2(54)SG
Supervisor Engine 6-E
Cisco IOS Software Release 12.2(54)SG
Supervisor Engine 7-E
Cisco IOS XE Software Release 3.0(1)SG
Supervisor Engine V-10GE
Cisco IOS Software Release 12.2(40)SG
Supervisor Engine 6-E
Cisco IOS Software Release 12.2(40)SG
Supervisor Engine 6L-E
Cisco IOS Software Release 12.2(52)SG
Supervisor Engine 7-E
Cisco IOS XE Software Release 3.0(1)SG
Supervisor Engine V-10GE
Cisco IOS Software Release 12.2(40)SG
Supervisor Engine 6-E
Cisco IOS Software Release 12.2(40)SG
Supervisor Engine 7-E
Cisco IOS XE Software Release 3.0(1)SG
Cisco WS-C4507R+E
Cisco WS-C4510R+E
Cisco WS-C4507R-E
Cisco WS-C4510R-E
®
Managing the Catalyst 4500E Series Switch
Network Management applications are instrumental in lowering Operating Expenditures (OPEX) while improving
network availability by simplifying and automating many of the day-to-day tasks associated with managing an end-toend network.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 12
Data Sheet
Cisco Network Assistant
The Cisco Network Assistant application manages standalone devices from anywhere on your intranet. Using its
GUI, you can perform multiple configuration tasks without using command-line interface (CLI) commands. You can
apply actions to multiple devices and ports at the same time for VLAN and quality-of-service (QoS) settings,
inventory and statistics reports, link and device monitoring, software upgrades, and many other networking features.
Cisco Network Assistant simplifies device management by offering an intuitive GUI, alternative modes for configuring
network devices, two levels of access, and comprehensive online help. It features two modes of display: device view
and topology view. In the device view, the Cisco Catalyst 4500 Series administrator may configure the switch,
configure ports on the switch, or configure groups of ports. In the topology view, the administrator may configure
VLAN settings, configure EtherChannels, and view a variety of reports on system and network status.
CiscoWorks LAN Management Solution
CiscoWorks LAN Management Solution (LMS) is an integrated suite of management functionality that simplify the
configuration, administration, monitoring, and troubleshooting of Cisco Borderless Networks. Built upon popular
Internet-based standards, CiscoWorks LMS enables network operators to manage the network through a browserbased interface that can be accessed anytime from anywhere within the network. The user experience allows for
maximum flexibility and quick-and-easy access to management functions and tasks reducing complexity and errorprone tasks typically associated with managing a network. The breadth and depth of device support coupled with
“day-one” device support program ensures that the 4500E Series Switch and the latest Cisco platforms are
supported and manageable the day they ship.
Once installed, out-of-the-box monitoring and troubleshooting dashboards provide immediate results and actionable
information to quickly isolate and fix network problems before they are service impacting. Work centers provide a
single place where operators can quickly provision, monitor and manage new Cisco Catalyst 4500E Series Switch
TM
value-added network services such as: Cisco EnergyWise, Cisco TrustSec , and AutoSmart Ports.
Network Analysis Module
Cisco NAM 2200 series appliance provides comprehensive operational visibility into Cisco Catalyst 4500 Series
Switch deployments. It combines application performance visibility, traffic analysis and troubleshooting, to enable
network administrators to effectively manage delivery of converged network services. The visibility provided by NAM
allows IT to deliver consistent end-user experience and improve service levels. It also helps to optimize resources
with comprehensive analysis of traffic and effective use of intelligent network services such as QoS and Cisco
WAAS. In addition, Cisco NAM improves operational efficiency with proactive detection of performance issues and
accelerated problem isolation and root-cause analysis
Physical Specifications
Table 6 lists physical specifications.
Table 6.
Physical Specifications of Cisco Catalyst 4500 Series Chassis
Specification
WS-C4503-E
WS-C4506-E
WS-C4507R+E and WSC4507R-E
WS-C4510R+E and WSC4510R-E
Dimensions (H x W x D)
12.25 x 17.31 x 12.50 in.
(31.12 x 43.97 x 31.70 cm)
17.38 x 17.31 x 12.50 in.
(44.13 x 43.97 x 31.70 cm)
19.19 x 17.31 x 12.50 in.
(48.74 x 43.97 x 31.70 cm)
24.35 x 17.31 x 12.50 in.
(61.84 x 43.97 x 31.70 cm)
Rack units (RU)
7 RU
10 RU
11 RU
14 RU
Chassis weight (with fan
tray)
32.25 lb (14.63 kg)
40.50 lb (18.37 kg)
44.50 lb (20.19 kg)
54.50 lb (24.73 kg)
Mounting
19- and 23-in. rack
compatible (19-in. rack and
cable guide hardware
included)
19- and 23-in. rack
compatible (19-in. rack and
cable guide hardware
included)
19- and 23-in. rack
compatible (19-in. rack and
cable guide hardware
included)
19- and 23-in. rack
compatible (19-in. rack and
cable guide hardware
included)
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 12
Data Sheet
Power Supply Indicators and Interfaces
Tables 7 and 8 describe power supply indicators and interfaces:
●
Fan cooling: Integrated in hot-insertion/hot-extraction unit
●
Good: Green
●
Fail: Red (faulty)
●
SNMP MIB supported
Table 7.
Cisco Catalyst 4500E Series Power Supply Specifications (Data Only)
Power Supply
1000W AC
1400W AC
1400W DC Triple Input
Integrated PoE
No (data only)
No (data Only)
No (data only)
Input current (rated)
12A at 100 VAC, 5A at 240 VAC
16A at 100 VAC, 7A at 240 VAC
2x -48 VDC at 15A
1x -48 VDC at 12.5A
● 12V at 83.4A
● 3.3V at 12.2A
Output current (data)
● 12V at 113.4A
● 3.3V at 12.2A
● 12V at 1360W
● 3.3V at 40W
Output power redundant mode
(data)
1000W + 40W
1360W + 40W
1400W + 40W
Output power combined mode
(data)
1667W
2473W
-
Heat dissipation
943 Btus per hour
1048 Btus per hour
1048 Btus per hour
Holdup time
20 ms
20 ms
20 ms
Hot swappable
Yes
Yes
Yes
Table 8.
Cisco Catalyst 4500E Series Power Supply Specifications (Data and PoE)
Power Supply
1300W AC
2800W AC
4200W AC
6000 AC
1400W DC with
PEM
2500W AC Power Shelf
Integrated PoE
Yes (up to 800W)
Yes (up to 1400W)
Yes (up to 3855W)
Yes (up to 4800W)
Up to 7500W
(minus the power
consumed for data)
when connected
directly to a DC
power plant or 2
external AC power
shelves
2500W per power
supply; 5000W per
shelf (minus the
power consumed
for data)
IEEE 802.3af/at
compliant
PoE/PoEP
Yes
Yes
Yes
Yes
Yes
Yes
Input current
(rated)
Output current
(data)
Output current
(PoE)
● 16A at 100
VAC
● 7A at 240 VAC
● 12V at 84.7A
● 3.3V at 12.5A
-50V at 16.7A
16A at 200 VAC
● 12V at 113.3A
● 3.3V at 12.1A
-50V at 28A
Output power
redundant mode
(data)
1000W + 40W
1360W + 40W
Output power
redundant mode
(PoE)
800W maximum
per power supply
1400W maximum
per power supply
Output power
combined mode
(data)
1667W
2473W
● 2x 12A at
100VAC
● 2x 12A at
100VAC
Or
● 2x 12A at
200VAC
Or
● 2x 16A at
200VAC
● 12V at 115.3A
● 3.3V at 12.5A
● 12V at 186.9A
● 3.3V at 12.5A
-50V at 77.1A
(200V)
-50V at 100.0A
(200V)
-50V at 38A (100V)
-50V at 38.5A
(120V)
1383W + 40W
2200W + 40W
● 3700W (220V)
● 1850W (110V)
2766W
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
● 31A at -60 VDC 15A at 200 VAC
(data only)
● 180A at -48
VDC (PoE)
● 4800W (220V)
● 1850W (110V)
4400W
● 12V at 120A
● 3.3V at 10A
-52 VDC at 50A
(total output per
supply)
140A at -48/-60
VDC
-52 VDC at 50A
(total output per
supply)
1360W + 40W
Up to 1400W
(through DC
supply)
Up to 7500W
(minus the power
consumed for data)
2500W per supply
(minus the power
consumed for data)
-
-
Page 6 of 12
Data Sheet
Power Supply
1300W AC
2800W AC
4200W AC
6000 AC
1400W DC with
PEM
2500W AC Power Shelf
Output power
combined mode
(PoE)
1333W
2333W
6700W (220V)
8700W (220V)
3800W (100V)
-
3360W (110V)
3360W (110V)
Heat dissipation
1568 Btus per hour
3580 BTU/hr
2720 BTU/hr
Data only: 1591
Btus per hour
1210 Btus per
hour, per power
supply
2387 Btus per hour
Data and voice:
2905 Btus per hour
Holdup rime
20 ms
20 ms
20 ms
20 ms
4 ms
20 ms
Hot swappable
Yes
Yes
Yes
Yes
Yes
Yes
Additional notes for Table 7 and 8:
●
Output power is per power supply unless otherwise stated
●
Heat dissipation numbers represent the power-conversion losses of the power supply in operation
●
The number of power devices supported will depend on customer configuration
Fan Trays
Each Cisco Catalyst 4500E Series and classic Cisco Catalyst 4500 Series chassis uses a single fan tray for cooling.
All fan trays are composed of independent fans. If one fan fails, the system will continue to operate without a
significant degradation in cooling. The system will detect and notify the user (through LED, command-line interface
[CLI], and SNMP) that a fan has failed and the tray needs to be replaced. Cisco Catalyst 4500E Series fans cannot
be interchanged with classic Cisco Catalyst 4500 Series fans. The classic Cisco Catalyst 4500 Series chassis needs
an E-Series fan tray in order to support the Metro Supervisor Engine 6-E.
Fabric-Redundancy Modules (Cisco WS-C4507R+E, WS-C4510R+E, WS-C4507R-E, and WSC4510R-E Only)
The Cisco Catalyst 4500 and 4500E Series redundancy scheme uses removable fabric-redundancy modules on the
passive backplane to switch traffic to the active supervisor engine. There is one fabric-redundancy module per line
card. Fabric-redundancy modules and redundant clocks ship standard with every Cisco Catalyst 4507R+E, 4507R-E,
4510R+E, and 4510R-E chassis. Fabric-redundancy modules cannot be interchanged between the Cisco Catalyst
4507R+E/4510R+E and 4507R-E/4510R-E chassis.
Environmental Conditions
The Cisco Catalyst 4500 and 4500E Series require the following conditions:
●
Operating temperature: 32 to 104ºF (0 to 40ºC)
●
Storage temperature: -40 to 167ºF (-40 to 75ºC)
●
Relative humidity: 10 to 90 percent, noncondensing
●
Operating altitude: -60 to 2000 meters (m)
Regulatory Standards Compliance
Table 9 lists the regulatory standards compliance of the Cisco Catalyst 4500 and 4500E Series.
Table 9.
Regulatory Standards Compliance
Specification
Standard
Regulatory compliance
CE Marking
Safety
● UL 60950
● CAN/CSA-C22.2 No. 60950
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 12
Data Sheet
Specification
Standard
● EN 60950
● IEC 60950
● TS 001
● AS/NZS 3260
● FCC Part 15 (CFR 47) Class A
● ICES-003 Class A
EMC
● EN55022 Class A
● CISPR22 Class A
● AS/NZS 3548 Class A
● VCCI Class A
● EN 55022
● EN 55024
● EN 61000-6-1
● EN 50082-1
● EN 61000-3-2
● EN 61000-3-3
● ETS 300 386
● NEBS Level 3
● ETS 300 019 Storage Class 1.1
Industry EMC, safety, and
environmental standards
● ETS 300 019 Transportation Class 2.3
● ETS 300 019 Stationary Use Class 3.1
● ETS 300 386
● CTR 12/13
● CTR 4
Telecom (E1)
● ACA TS016
● FCC Part 68
● Canada CS-03
Telecom (T1)
● JATE Green Book
ROHS Compliance
ROHS5
Power and MTBF Information
Table 10 gives power and MTBF information for different chassis
Table 10.
Power and MTBF Info
Part Number
Max Rated Power (W)
Rated MTBF (Hours)
WS-C4503-E
60
1,064,279
WS-C4506-E
120
710,119
WS-C4507R+E
135
248,630
WS-C4510R+E
200
179,714
WS-C4507R-E
135
365,896
WS-C4510R-E
200
290,525
Note:
All power numbers shown in the table above are maximum values recommended for facility power and cooling
capacity planning. These figures are not indicative of the actual power draw during operation. Typical power draw is
about 20% lower than the maximum value shown.
Ordering Information
Table 11 lists the ordering information for chassis, power supplies, supervisor engines, and memory that are
commonly used with the Cisco Catalyst 4500 Series.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 12
Data Sheet
Table 11.
Ordering Information
Product Number
Description
WS-C4503-E
Cisco Catalyst E-Series 4503 switch (3-slot chassis), fan, no power supply
WS-C4506-E
Cisco Catalyst E-Series 4506 switch (6-slot chassis), fan, no power supply
WS-C4507R-E
Cisco Catalyst E-Series 4507R switch (7-slot chassis), fan, no power supply, redundant supervisor capable
WS-C4507R+E
Cisco Catalyst E-Series 4507R+E switch (7-slot chassis), fan, no power supply, redundant supervisor
capable
WS-C4510R-E
Cisco Catalyst E-Series 4510R switch (10-slot chassis), fan, no power supply; redundant supervisor
capable
WS-C4510R+E
Cisco Catalyst E-Series 4510R+E switch (10-slot chassis), fan, no power supply; redundant supervisor
capable
PWR-C45-1000AC
Cisco Catalyst 4500 Series 1000W AC power supply (data only)
PWR-C45-1400AC
Cisco Catalyst 4500 Series 1400W AC power supply (data only)
PWR-C45-1300ACV
Cisco Catalyst 4500 Series 1300W AC power supply (with integrated PoE)
PWR-C45-2800ACV
Cisco Catalyst 4500 Series 2800W AC power supply (with integrated PoE)
PWR-C45-4200ACV
Cisco Catalyst 4500 Series 4200W AC power supply (with integrated PoE)
PWR-C45-6000ACV
Cisco Catalyst 4500 Series 6000W AC power supply (with integrated PoE)
PWR-C45-1400DC-P
Cisco Catalyst 4500 Series 1400W DC power supply with integrated power entry module (PEM)
PWR-C45-1400DC
Cisco Catalyst 4500 Series triple input 1400W DC power supply (data only)
WS-P4502-1PSU
Cisco Catalyst 4500 Series auxiliary power shelf (2-slot), including 1 PWR-4502
PWR-4502
Cisco Catalyst 4500 Series auxiliary power-shelf redundant power supply
WS-X4013+
Cisco Catalyst 4500 Series Supervisor Engine II-Plus
WS-X4013+TS
Cisco Catalyst 4500 Series Supervisor Engine II-Plus-TS, twelve 10/100/1000 PoE (RJ-45) and eight 1000X SFP ports included on supervisor-engine faceplate
WS-X4013+10GE
Cisco Catalyst 4500 Series Supervisor Engine II-Plus-10GE
WS-X4515
Cisco Catalyst 4500 Supervisor Engine IV
WS-X4516
Cisco Catalyst 4000 and 4500 Supervisor Engine V
WS-X4516-10GE
Cisco Catalyst 4500 Series Supervisor Engine V-10GE
WS-X45-Sup6-E
Cisco Catalyst 4500 Series Supervisor Engine 6-E
WS-X45-Sup6L-E
Cisco Catalyst 4500 Series Supervisor Engine 6L-E
MEM-C4K-FLD64M
Compact Flash memory, 64-MB option
MEM-C4K-FLD128M
Compact Flash memory, 128-MB option
MEM-X45-512MB-E
Cisco Catalyst 4500 Series Supervisor Engine 6-E, 512-MB option
Warranty
Cisco Catalyst 4500E Series and Cisco Catalyst 4500 switches are covered by the Cisco limited lifetime hardware
warranty. For more information, visit http://www.cisco.com/en/US/docs/general/warranty/English/LH2DEN__.html.
Note:
If you purchased a Cisco Catalyst 4500 Series chassis before May 1, 2009, it is covered by the Cisco
90-day limited hardware warranty. For more information, visit
http://www.cisco.com/en/US/docs/general/warranty/English/901DEN__.html.
Cisco Technical Support Services
Cisco offers Cisco Technical Support Services to help ensure that your Cisco products operate efficiently, remain
highly available, and benefit from current system software to assist you in effectively managing your network service
while controlling operational costs.
Cisco Technical Support Services provide significant benefits that go beyond what is offered under the Cisco
warranty policy.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 12
Data Sheet
®
Services available under a Cisco SMARTnet service contract that are not covered under a warranty include the
following:
●
Latest software updates
●
Rapid replacement of hardware in next-day, 4-hour, or 2-hour dispatch options
●
Ongoing technical support through Cisco Technical Assistance Center (TAC)
●
Registered access to http://www.cisco.com
Tables 12 and 13 list the components and competitive differentiators of Cisco Technical Support Services.
Table 12.
Technical Support Services: Components
Service Feature Overview
Benefits
Software support
Offers maintenance and minor and major updates for licensed feature set. Downloading new maintenance
releases, patches, or updates of Cisco IOS Software helps to enhance and extend the useful life of Cisco
devices. Through major software updates it is possible to extend the life of equipment and maximize
application technology investments by:
● Increasing the performance of current functions
● Adding new capability that, in many cases, requires no additional hardware investment
● Enhancing network and application availability, reliability, and stability
®
TAC support
With more than 1000 highly trained customer support engineers, 390 CCIE certifications, and access to
13,000 research and development engineers, Cisco TAC complements your in-house staff with a high level
of knowledge in voice, video, and data communications networking technology. Its sophisticated callrouting system quickly routes calls to the correct technology personnel. The Cisco TAC is available 24
hours a day, 365 days a year.
Cisco.com
This award-winning website provides 24-hour access to an extensive collection of online product and
technology information, interactive network-management and troubleshooting tools, and knowledgetransfer resources that can help customers reduce costs by increasing staff self-sufficiency and
productivity.
Advance hardware replacement
Advance replacement and onsite field-engineer options supply fast access to replacement hardware and
field resources for installing hardware, minimizing the risk of potential network downtime.
Table 13.
Technical Support Services: Competitive Differentiators
Feature
Benefits
Worldwide Virtual Lab
● TAC training
This extensive lab of Cisco equipment and Cisco IOS Software releases provides an invaluable
engineering resource and knowledge base for training, product information, and recreation and testing of
selected network issues to help decrease time to resolution.
● Boot camps
● Tech calls
Tech forums
Cisco is committed to providing customers the latest in technology support. These TAC training programs
assist customers in case avoidance as well as provide knowledge transfer of Cisco networking expertise.
Cisco Live
A powerful suite of Internet-enabled tools with firewall-friendly features; these secure, encrypted Java
applets can turn a simple phone call into an interactive collaboration session, allowing a customer and
Cisco TAC support engineer to work together more effectively.
Global logistics
Delivers award-winning, worldwide hardware-replacement support with 650 depots, covering 120 countries,
at a US$2.3 billion investment in inventory, using 10,000 onsite field engineers.
Cisco IOS Software
Employs 100 discrete technologies with more than 2000 features. 400 new features are added each year.
Cisco IOS Software is installed in more than 10 million devices and is running on more than 10,000
networks worldwide. It operates on the world’s largest IPv6 and VoIP networks and in all major service
provider networks worldwide.
For More Information
To learn more about how you can take advantage of Cisco Technical Support Services, talk to your Cisco
representative or visit Cisco Technical Support Services at
http://www.cisco.com/en/US/products/svcs/ps3034/ps2827/serv_category_home.html.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 10 of 12
Data Sheet
For additional information about the Cisco Catalyst 4500 Series, visit http://www.cisco.com/go/catalyst4500.
For additional information about Cisco products, contact:
●
United States and Canada: 800 553-NETS (6387)
●
Europe: 32 2 778 4242
●
Australia: 612 9935 4107
●
Other: 408 526-7209
●
http://www.cisco.com
Cisco and Partner Services for Next-Generation Cisco Catalyst Modular Switches
Enable the borderless network architecture using personalized services from Cisco and our partners. Through a
discovery process that begins with understanding your business objectives, we help you integrate the nextgeneration Cisco Catalyst modular switches into your architecture and incorporate network services onto that
platform. Sharing knowledge and leading practices, we support your success every step of the way as you deploy,
absorb, manage, and scale new technology. Choose from a flexible suite of support services designed to meet your
business needs and help you maintain high-quality network performance while controlling operational costs.
For more information about services from Cisco and our partners, visit http://www.cisco.com/go/services.
Table 14 lists available technical services.
Table 14.
Available Technical Services
Technical Services
®
Cisco SMARTnet Service
● Around-the-clock, global access to the Cisco Technical Assistance Center (TAC)
● Unrestricted access to the extensive Cisco.com knowledge base and tools
● Next-business-day, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement and onsite parts replacement and installation available7
● Ongoing operating system software updates within the licensed feature set8
● Proactive diagnostics and real-time alerts on Smart Call Home enabled devices
Cisco Smart Foundation Service
● Next business day advance hardware replacement as available
● Business hours access to SMB TAC (access levels vary by region)
● Access to Cisco.com SMB knowledge base
● Online technical resources through Smart Foundation Portal
● Operating system software bug fixes and patches
Cisco SP Base Service
● Around-the-clock, global access to the Cisco TAC
● Registered access to Cisco.com
● Next business day, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement. Return to factory option available7
● Ongoing operating system software updates8
● Available direct from Cisco only to qualified service providers
7
Advance hardware replacement is available in various service-level combinations. For example, 8x5xNBD indicates that shipment
will be initiated during the standard 8-hour business day, 5 days a week (the generally accepted business days within the relevant
region), with next business day (NBD) delivery. Where NBD is not available, same day ship is provided. Restrictions apply; please
review the appropriate service descriptions for details.
8
Cisco operating system updates include the following: maintenance releases, minor updates, and major updates within the
licensed feature set.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 11 of 12
Data Sheet
Printed in USA
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-436089-09
01/11
Page 12 of 12
ITEM 2
Data Sheet
Cisco Catalyst 4500E Supervisor Engine 7-E: Leading Borderless
Network Access and Aggregation Supervisor Engine
Overview
®
®
Establishing borderless leadership is now easier than ever to achieve with the new Cisco Catalyst 4500E
Supervisor Engine 7-E (Figure 1), an enterprise-class borderless network access and aggregation supervisor engine
designed to provide 848 Gbps per system with E-Series chassis. Cisco Catalyst 4500E Supervisor Engine 7-E is the
first Cisco Catalyst supervisor engine to provide 48 Gbps per slot with Flexible NetFlow, Advanced Security,
combined with reduced total cost of ownership (TCO) and excellent investment protection. With these capabilities, 4
10G uplinks, and 384 10/100/1000 PoE (240 ports of PoEP) ports, this supervisor engine is undoubtedly the Cisco
leading borderless network access Cisco Catalyst supervisor engine. Supervisor Engine 7-E is built with priceperformance aggregation deployments in mind, providing increased Gigabit Ethernet and 10 Gigabit Ethernet fiber
density along with hardware capabilities to support enterprise-class aggregation functionalities. Supervisor Engine 7E facilitates borderless user experiences for enterprise, public sector, mid-market, and commercial customer
deployment business-critical applications.
™
Borderless network leadership is extended with important drivers - Hardware readiness for Cisco TrustSec ,
medianet, Flexible NetFlow, Cisco EnergyWise - and other feature enhancements enabled by the Cisco Catalyst
4500E Supervisor Engine 7-E. Backward and forward compatibility with most existing Cisco Catalyst 4500 and
4500E line cards assures deeper customer satisfaction with the industry’s best investment protection architecture.
The Cisco Catalyst 4500E Supervisor Engine 7-E delivers several new technology breakthroughs and industry firsts,
extending the Cisco Catalyst 4500 Series placement from premium wiring closet solution into next-generation
borderless access and aggregation deployments.
The Supervisor Engine 7-E offers the following key leading innovations and capabilities:
●
Enables 10+ years of investment protection through backward and forward compatibility
●
First Cisco Catalyst switch with 48 Gbps per slot (848 G per system)
●
Enables around 5 microseconds of latency to and from any 10G port
●
First Cisco Catalyst switch with campus Flexible NetFlow (FNF)
●
First Cisco Catalyst switch offering Cisco IOS XE Software services
●
First Cisco Catalyst switch with less than 10ms ISSU high availability
●
First and only modular switch with 8 bi-directional SPAN and/or RSPAN sessions
®
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 1
Data Sheet
Figure 1.
Cisco Catalyst 4500E Supervisor Engine 7-E
Cisco Catalyst 4500E Supervisor Engine 7-E Feature Highlights
The Cisco Catalyst 4500E Supervisor Engine 7-E is the first Cisco Catalyst supervisor engine to provide nonblocking
48 Gbps per slot bandwidth and Flexible NetFlow for optimized application visibility. In addition to this, the
enterprise-class Cisco Catalyst 4500E Supervisor Engine 7-E offers the following:
●
Performance/Scalability
◦
848 Gbps switching capacity with 250 Mpps of throughput
◦
4 nonblocking 10 Gigabit Ethernet uplinks [SFP+]
◦
SFP support on uplinks to offer flexibility for up to 4 Gigabit Ethernet
◦
384 ports of nonblocking 10/100/1000
◦
PoEP (30W) capabilities on all ports in a line card simultaneously
◦
196 ports of nonblocking Gig SFP
◦
100 ports of 10G SFP+ (4 Uplinks ports + 96 Linecard ports)
◦
128K Flexible NetFlow entries in hardware
◦
External USB and SD card support for flexible storage options
◦
256K Routing Entries for high-end campus access and aggregation deployments
◦
IPv6 support in hardware, providing wire-rate forwarding for IPv6 networks
◦
Dynamic hardware forwarding-table allocations for ease of IPv4-to-IPv6 migration
◦
Scalable routing (IPv4, IPv6, and multicast) tables, Layer 2 tables, and ACL and QoS entries to make sure
of 8 queues per port and comprehensive security policies per port
●
Infrastructure Services
◦
Cisco IOS XE Software, the modular open application platform for virtualized borderless services
◦
Maximum resiliency with redundant components, Nonstop Forwarding/Stateful Switchover (NSF/SSO), and
In-Service Software Upgrade (ISSU) support
◦
Network virtualization through Multi-VRF technology for Layer 3 segmentation
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 12
Data Sheet
◦
Automation through Embedded Event Manager (EEM), Cisco Smart Call Home, AutoQoS, and Auto
SmartPorts for fast provisioning, diagnosis, and reporting
●
Borderless Network Services
◦
Optimized application performance through deep visibility with Flexible Netflow supporting rich Layer 2/3/4
information (MAC, VLAN, TCP Flags) and synthetic traffic monitoring with IP SLA
●
◦
Medianet capabilities to simplify video quality of service, monitoring, and security
◦
Energy efficient design with Cisco EnergyWise technology to manage network, PoEP, and PC
Investment Protection and Reduced TCO
◦
Full backward compatibility with 6 G, 24 G, and 48 Gbps slot line cards with no performance degradation
The Cisco Catalyst 4500E Supervisor Engine 7-E is compatible with classic Cisco Catalyst 4500 line cards, and
power supplies, providing full investment protection. Supervisor Engine 7-E is not compatible with classic Catalyst
4500 chassis. When you deploy the Cisco Catalyst 4500E Supervisor Engine 7-E with classic line cards, all of the
new features except the 24 Gbps and 48 Gbps per-slot switching capacity are inherited.
Predictable Performance and Scalability
The Supervisor Engine 7-E is the first Cisco Catalyst supervisor engine to provide 48 Gbps per slot switching
capacity. Table 1 highlights the performance and scalability enhancements of the Cisco Catalyst 4500E Supervisor
Engine 7-E.
Table 1.
Cisco Catalyst 4500E Supervisor Engine 7-E Performance and Scalability Features
Feature and Description
Supervisor Engine 7-E
Centralized Switching Capacity
848 Gbps
Per-Slot Switching Capacity
48 Gbps
Throughput
● 250 Mpps for IPv4
● 125 Mpps for IPv6
IPv4 Routing Entries
256,000
IPv6 Routing Entries
128,000
Multicast Routes
32,000 (Available with Cisco IOS XE Software Release 3.1.0 SG)
CPU
Dual Core 1.5 GHz
CPU Queues
64
Synchronous Dynamic RAM (SDRAM)
2 GB upgradable to 4 GB
NVRAM
1G
Security and QoS Hardware Entries
128,000
Cisco Network Admission Control (NAC) and Dynamic Host
Configuration Protocol (DHCP) Snooping Entries
12,000
MAC addresses
55,000
Active VLANs
4,096
Spanning Tree Protocol Instances
10,000
Switched Virtual Interfaces (SVIs)
4,096
Switched Port Analyzer (SPAN)
Maximum of 8 sessions: ingress and/or egress
The Supervisor Engine 7-E is also optimized for multimedia applications with its advanced multicast support offered
by features such as Protocol Independent Multicast (PIM) and Source-Specific Multicast (SSM), giving your network
additional scalability to support multimedia applications.
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 12
Data Sheet
Continued Innovations Through Infrastructure Services
Modular Open Application Platform, Cisco IOS XE Software
Cisco IOS XE Software is the next generation operating system for the Cisco Catalyst 4500E Supervisors, beginning
with the Supervisor 7-E. Cisco continues to evolve Cisco IOS Software to support next-generation switching
hardware and provide increased architectural flexibility to deliver quick adoption of future Cisco Borderless Networks
services, while making sure of customer investment protection in Cisco IOS Software.
Cisco IOS XE Software provides the following customer benefits:
●
Cisco IOS XE Software provides a modern operating system that can take advantage of the multicore CPU
architecture of the next generation Cisco Catalyst 4500 system with Supervisor 7-E.
●
Cisco IOS XE Software makes sure of customer investment protection in the existing Cisco IOS Software.
With Cisco IOS XE Software, today’s Cisco IOS Software becomes a “Cisco IOS Software package” with a
consistent feature set and operational look and feel. This allows a transparent migration experience.
●
Cisco IOS XE Software supports service virtualization capability that allows the Cisco Catalyst 4500 to host
applications other than Cisco IOS Software, customer written applications, or third-party applications in
parallel with Cisco IOS Software. The hosted application can communicate with Cisco IOS Software to use its
rich feature sets. This benefit allows a customer to quickly adopt new technologies using proven code, while
keeping Cisco IOS Software simple and robust. Cisco IOS XE Software enables Cisco Catalyst 4500 to be an
open service platform and is a primary anchor to enable future Cisco Borderless Networks innovations.
Best-in-Class Resiliency
The Cisco Catalyst 4500E Series was designed for excellent nonstop communications with noninterrupted hardware
switching. With Cisco IO XE Software customers continue to reap the benefit of this best-in-class resiliency in
various ways.
ISSU allows you to upgrade or downgrade complete Cisco IOS Software images with minimal (10msec) to no
disruption to the network when using a redundant Cisco Catalyst 4500E Series system with dual supervisor engines
7-E. Facilitating rapid, nondisruptive software upgrade for new line cards, new power supplies, new features, or bug
fixes, ISSU offers continuous packet forwarding during the supervisor-engine switchover running different Cisco IOS
Software releases.
NSF/SSO offers continuous packet forwarding during supervisor-engine switchover. Information is fully synchronized
between supervisor engines to allow the standby supervisor engine to immediately take over in subsecond time if the
primary fails.
NSF/SSO and ISSU dramatically improve the network reliability and availability in a Layer 2 or Layer 3 environment.
NSF/SSO and ISSU are essential for business-critical applications such as voice over IP (VoIP). These features help
ensure that VoIP calls are not dropped.
In addition to redundant power supplies, fans, and clock modules, the Cisco Catalyst 4510R+E, 4507R+E, 4510R-E,
and 4507R-E chassis models support 1 + 1 supervisor-engine redundancy, using the Supervisor Engine 7-E. The
primary supervisor engine is active and is responsible for normal system operation. The secondary supervisor
engine serves as a secondary standby, monitoring the operation of the primary supervisor engine. The resiliency
features of the Cisco Catalyst 4500 prevent network outages that could result in lost business and revenue.
Apart from the above, Supervisor Engine 7-E has resiliency built into its uplinks. Figure 2 shows the uplink options
on Supervisor Engine 7-E.
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 12
Data Sheet
Figure 2.
High-Availability and Uplink Options for Supervisor Engine 7-E
Simplified Operations Through Automation
As campus switching has grown to support increasing enterprise demands, so has the need to deploy and manage
new and evolving technologies. Simplified operations are critical in meeting these challenges and achieving
increased operational efficiency through proactive management and reduction in unplanned network downtime.
The Cisco Catalyst Supervisor Engine 7-E offers the following rich set of capabilities for simplified operations:
●
Auto Install and AutoQoS for fast deployment
●
Config Rollback for improved config management
●
EEM, Smart Call Home, GOLD, TDR for simplified operations
●
Flexible NetFlow and IP SLA for enhanced visibility
●
Cisco EnergyWise for simplified power management
●
ISSU for simplified change management
Optimized Application Visibility with Flexible NetFlow
Cisco IOS Flexible NetFlow is the next generation in flow technology, allowing optimization of the network
infrastructure, reducing operation costs, improving capacity planning and security incident detection with increased
flexibility and scalability. The Cisco Catalyst 4500E Supervisor Engine 7-E is the first Cisco Catalyst supervisor
engine to provide optimized application visibility with Flexible NetFlow with a capability of 128K Flexible NetFlow
Entries. The Supervisor Engine 7-E, with custom-built ASIC, delivers next-generation flow technology with
unprecedented flexibility and comprehensive visibility extending from Layer 2 (MAC, VLAN) to Layer 4 (TCP, UDP
flags, and so on).
The flow data collected by Flexible NetFlow can be exported to external collector for analysis and reporting, or
tracked by Embedded Event Manager (EEM).The Cisco Catalyst 4500E Supervisor Engine 7-E enables powerful,
on-box and customizable event correlation and policy actions with EEM. This allows the switches to trigger
customized event alarms or policy actions when the predefined condition is met. With no external appliance
required, customers are able to use existing infrastructure to perform traffic monitoring, making traffic analysis
economical even on large IP network.
Details on Cisco Flexible NetFlow are available at
http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6555/ps6601/ps6965/product_data_sheet0900aecd8
04b590b.html.
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 12
Data Sheet
Investment Protection with Chassis and Line Card Support
Already-installed Cisco Catalyst 4500E chassis with classic and E-Series line cards can take advantage of the new
features and functions of the Supervisor Engine 7-E on all ports with a simple supervisor-engine upgrade. However,
to take advantage of the increased switching capacity of 48 Gbps per slot, the Cisco Catalyst 4500E Series chassis
(including R+E chassis) and the select new E-Series line cards are required. You can mix and match Cisco Catalyst
4500E Series line cards and classic line cards in an E-Series chassis with no performance degradation to either linecard type. Table 2 shows the supervisor-engine and line-card slot-assignment options in the Cisco Catalyst 4500E
Series chassis.
Table 2.
Cisco Catalyst 4500E Chassis Slot-Assignment Options
Chassis
Single Supervisor Engine
7-E Slot Assignments
Redundant Supervisor
Engine 7-E Slot
Assignments
E-Series Line-Card Slot
Options
Classic Line-Card Slot
Options
Cisco Catalyst 4503-E
Slot 1
-
Slots 2 and 3
Slots 2 and 3
Cisco Catalyst 4506-E
Slot 1
-
Slots 2 through 6
Slots 2 through 6
Cisco Catalyst 4507R+E
Slot 3 or 4
Slots 3 or 4
Slots 1, 2, and 5 to 7
Slots 1, 2, and 5 to 7
Cisco Catalyst 4510R+E
Slots 5 or 6
Slots 5 or 6
Slots 1 to 4, and 7 to 10
Slots 1 to 4, and 7 to 10
Cisco Catalyst 4507R-E
Slot 3 or 4
Slots 3 or 4
Slots 1, 2, and 5 to 7
Slots 1, 2, and 5 to 7
Cisco Catalyst 4510R-E
Slots 5 or 6
Slots 5 or 6
Slots 1 to 4, and 7 to 10
Slots 1 to 4, and 7 to 10
Table 3 summarizes the performance capacities of the Supervisor Engine 7-E on a per-chassis basis.
Table 3.
Cisco Catalyst 4500 Supervisor Engine 7-E Bandwidth per slot for different Chassis
Supervisor
Engine 7-E
(WS-X45-Sup 7-E)
Cisco Catalyst
4503-E Chassis
Cisco Catalyst
4506-E Chassis
Cisco Catalyst
4507R+E Chassis
Cisco Catalyst
4510R+E Chassis
Cisco Catalyst
4507R-E Chassis
Cisco Catalyst
4510R-E Chassis
48Gbps/Slot
48 Gbps/Slot
48 Gbps/Slot
48 Gbps/Slot
24 Gbps/Slot
24 Gbps/Slot
IPv6 Support
IPv6 is important for the future of IP networking and is critical for the expansion of IP address space in the future.
IPv6 capability is required by many companies and is being mandated by governments worldwide. The Cisco
Catalyst 4500 Supervisor Engine 7-E supports IPv6 Unicast and Multicast in hardware for full line-rate forwarding
performance of up to 125 Mpps. The Supervisor Engine 7-E also dynamically allocates hardware table space
between IPv4 and IPv6 routes to maximize tablespace usage for optimal IPv4-to-IPv6 migration The Supervisor
Engine 7-E supports Multicast Listener Discovery (MLD) Snooping for IPv6, enhancing performance and reducing
network traffic by allowing a switch to dynamically add and remove hosts from a multicast group.
Table 4 highlights the IPv6 capabilities of the Supervisor Engine 7-E.
Table 4.
Summary of Supervisor Engine 7-E IPv6 Capabilities
Feature and Description
Supervisor Engine 7-E
IPv6 Support
Unicast and Multicast forwarding done in hardware
IPv6 Performance
125 Mpps
IPv6 Routing Entries
128,000
Dynamic Hardware Route Table Allocations
Yes
MLD Snooping for IPv6
Yes, in hardware
uRPFv6: Strict Mode
Yes, in hardware
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 12
Data Sheet
Features at a Glance
Cisco IOS XE Software LAN Base: Feature set on the Supervisor 7-E based bundles. Focused on providing Layer
2 features for access.
Cisco IOS XE Software IP Base: Upgradable with a software activation license (SAL). Includes all Layer 2 features
and some basic Layer 3 features. ISSU/SSO is supported in this package.
Cisco IOS XE Software Enterprise Services: Upgradable with a SAL; supports full Layer 3 protocols and advanced
features such as complete routing scalability (256K), BGP, Virtual Routing and Forwarding, Policy-Based Routing,
and so on.
These features can be enabled using the software-licensing mechanism. For details on software licensing, see
"Licensing" section later in this document or visit http://www.cisco.com/go/sa.
For details on the supported features in above 3 images see Cisco IOS XE 3.1.0 SG Release Notes below.
http://www.cisco.com/en/US/docs/switches/lan/catalyst4500/release/note/OL_23474.html.
Industry Standards
●
Ethernet: IEEE 802.3
●
10 Gigabit Ethernet: IEEE 802.3ae
●
10GBASE-R (SFP+)
●
IEEE 802. 1D Spanning Tree Protocol
●
IEEE 802.1w Rapid Reconfiguration of Spanning Tree
●
IEEE 802. 1s Multiple VLAN Instances of Spanning Tree
●
IEEE 802.3 ad LACP
●
IEEE 802. 1p CoS Prioritization
●
IEEE 802.1Q VLAN
●
IEEE 802. 1X User Authentication
●
RMON I and II standards
Supported Cisco Catalyst 4500E Series Line Cards and Modules
●
WS-X4748-RJ45V+E: Cisco Catalyst 4500E 48-Port PoE 802.3at 10/100/1000 (RJ45)
●
WS-X4712-SFP+E: Cisco Catalyst 4500E Series 12-Port 10GbE (SFP+)
●
WS-X4648-RJ45V-E: Cisco Catalyst 4500E Series, 48-port 802.3af PoE 10/100/1000 (RJ-45)
●
WS-X4648-RJ45V+E: Cisco Catalyst 4500E Series 48-Port Premium PoE 10/100/1000 (RJ-45)
●
WS-X4648-RJ45-E: Cisco Catalyst 4500E Series, 48-port 10/100/1000 (RJ-45)
●
WS-X4606-X2-E: Cisco Catalyst 4500E Series, 6-port 10 Gigabit Ethernet (X2)
●
WS-X4624-SFP-E: Cisco Catalyst 4500E Series 24-Port GE (SFP)
●
WS-X4612-SFP-E: Cisco Catalyst 4500E Series 12-port GE (SFP)
●
CVR-X2-SFP: Twin gigabit converter module
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 12
Data Sheet
Supported Cisco Catalyst 4500 Classic Line Cards and Modules
●
WS-X4148-FE-BD-LC: Cisco Catalyst 4500 Fast Ethernet Switching Module, 48-port 100BASE-BX-D SMF
(LC)
●
WS-X4124-FX-MT: Cisco Catalyst 4000 Fast Ethernet Switching Module, 24-port 100BASE-FX (MT-RJ)
●
WS-X4148-FX-MT: Cisco Catalyst 4500 Fast Ethernet Switching Module, 48-port 100BASE-FX multimode
fiber (MMF)
●
WS-X4124-RJ45: Cisco Catalyst 4500 10/100 Module, 24 ports (RJ-45)
●
WS-X4148-RJ: Cisco Catalyst 4500 10/100 Module, 48 ports (RJ-45)
●
WS-X4148-RJ21: Cisco Catalyst 4500 10/100 Module, 48-port telco (4 x RJ-21)
●
WS-X4248-RJ21V: Cisco Catalyst 4500 PoE 802.3af 10/100, 48 ports (RJ-21)
●
WS-X4224-RJ45V: Cisco Catalyst 4500 PoE 803.3af 10/100, 24 ports (RJ-45)
●
WS-X4248-RJ45V: Cisco Catalyst 4500 PoE 802.3af 10/100, 48 ports (RJ-45)
●
WS-X4248-FE-SFP: Cisco Catalyst 4500 Fast Ethernet Switching Module, 48-port 100BASE-X (SFP)
●
WS-X4232-GB-RJ: Cisco Catalyst 4500 32-Port 10/100 (RJ-45), 2 Gigabit Ethernet (GBIC) modules
●
WS-X4302-GB: Cisco Catalyst 4500 Gigabit Ethernet Module, 2 ports (GBIC)
●
WS-X4306-GB: Cisco Catalyst 4500 Gigabit Ethernet Module, 6 ports (GBIC)
●
WS-X4506-GB-T: Cisco Catalyst 4500 Gigabit Ethernet Module, 6 ports 10/100/1000 802.3af PoE or
1000BASE-X (SFP)
●
WS-X4418-GB: Cisco Catalyst 4500 Gigabit Ethernet Module, server switching 18 ports (GBIC)
●
WS-X4448-GB-SFP: Cisco Catalyst 4500 Gigabit Ethernet Module, 48 ports 1000BASE-X (optional SFPs)
●
WS-X4424-GB-RJ45: Cisco Catalyst 4500 24-Port 10/100/1000 Module (RJ-45)
●
WS-X4448-GB-RJ45: Cisco Catalyst 4500 48-Port 10/100/1000 Module (RJ-45)
●
WS-X4548-GB-RJ45: Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45)
●
WS-X4524-GB-RJ45V: Cisco Catalyst 4500 PoE 802.3af 10/100/1000, 24 ports (RJ-45)
●
WS-X4548-GB-RJ45V: Cisco Catalyst 4500 PoE 802.3af 10/100/1000, 48 ports (RJ-45)
●
WS-X4548-RJ45V+: Catalyst 4500 PoE+ Ready 10/100/1000, 48-Port (RJ45)
Supported Pluggables
●
10 Gbps Optics:
◦
SFP-10G-SR: Cisco 10GBASE-SR SFP+ Module for MMF
◦
SFP-10G-LRM: 10GBASE-LRM SFP+ transceiver module for MMF and SMF, 1310-nm wavelength, LC
duplex connector
●
◦
SFP-H10GB-CU1M: 1-m 10G SFP+ Twinax cable assembly
◦
SFP-H10GB-CU3M: 3-m 10G SFP+ Twinax cable assembly
◦
SFP-H10GB-CU5M: 5-m 10G SFP+ Twinax cable assembly
1 Gbps Optics:
◦
GLC-BX-D: 1000BASE-BX10 SFP module for single-strand SMF, 1490-nm TX/1310-nm RX wavelength
◦
GLC-BX-U: 1000BASE-BX10 SFP module for single-strand SMF, 1310-nm TX/1490-nm RX wavelength
◦
GLC-SX-MM: 1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength
◦
GLC-LH-SM: 1000BASE-LX/LH SFP transceiver module for MMF and SMF, 1300-nm wavelength
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 12
Data Sheet
For details about the different optical modules and the minimum Cisco IOS Software release required for each of the
supported optical modules, visit
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html
Software Requirements
The Cisco Catalyst 4500 Series Supervisor Engine 7-E is supported only in Cisco IOS Software and is not supported
in the Cisco Catalyst Operating System Software. The minimum software versions are as follows:
●
Supervisor Engine 7-E, Cisco IOS XE Software Release 3.1.0 SG
Environmental Conditions
●
Operating temperature: 32 to 104ºF (0 to 40ºC)
●
Storage temperature: -40 to 167ºF (-40 to 75ºC)
●
Relative humidity: 10 to 90 percent, noncondensing
●
Operating altitude: -60 to 2000m
Power and MTBF Information
Active Supervisor Power = 280W
Standby Supervisor Power = 224W
The above figure is not indicative of the actual power draw during operation. This is the absolute maximum value
recommended for facility power and cooling capacity planning. Typical power draw is about 20% lower than the
maximum value shown.
MTBF = 155,241 Hours
Regulatory Standards Compliance
Table 5 shows regulatory standards compliance information, and Table 6 provides ordering information.
Table 5.
Cisco Catalyst 4500 Supervisor Engine 7-E Regulatory Standards Compliance
Specification
Standard
Regulatory Compliance
CE marking
Safety
● UL 60950CAN/CSA-C22.2 No. 60950
● EN 60950
● IEC 60950
● TS 001
● AS/NZS 3260
EMC
● FCC Part 15 (CFR 47) Class A
● ICES-003 Class A
● EN55022 Class A
● CISPR22 Class A
● AS/NZS 3548 Class A
● VCCI Class A
● ETS 300 386
● EN 55022
● EN 55024
● EN 61000-6-1
● EN 50082-1
● EN 61000-3-2
● EN 61000-3-3
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 12
Data Sheet
Specification
Standard
Industry EMC, Safety, and
Environmental Standards
● GR-63-Core Network Equipment Building Standards (NEBS) Level 3
● GR-1089-Core Level 3
● ETS 300 019 Storage Class 1.1
● ETS 300 019 Transportation Class 2.3 (pending)
● ETS 300 019 Stationary Use Class 3.1
● ETS 300 386
ROHS Compliance
Table 6.
ROHS5
Ordering Information
Product Number
Description
WS-X45-SUP7-E
Cisco Catalyst 4500E Series Supervisor, 848 Gbps
WS-C4510RE-S7+96V+
4510R+E Chassis, Two WS-X4748-RJ45V+E, Sup7-E
S45U-31-01XO
Cisco Catalyst 4500 Supervisor Engine 7-E Cisco IOS Software XE release 3.1.0 SG non-crypto universal
image
S45ULK9-31-01XO
Cisco Catalyst 4500 Supervisor Engine 7-E Cisco IOS Software XE release 3.1.0 SG crypto universal
C4500E-LB
LAN BASE software license
C4500E-IPB
IP BASE software license
C4500E-LIC=
Base product ID for paper delivered software upgrade licenses
C4500E-LB-IPB
LAN BASE to IP BASE upgrade license (paper delivery)
C4500E-LB-ES
LAN BASE to Enterprise Services upgrade license (paper delivery)
C4500E-IP-ES
IP BASE to Enterprise Services upgrade license (paper delivery)
C4500E-LIC-PAK
Base product ID for paper delivered software licenses for spare Supervisor Engine 7-E
C4500E-IP-ES-S
IP BASE to Enterprise Services upgrade license for spare Supervisor Engine7-E (paper delivery)
C4500E-IPB-S
IP BASE software license for spare Supervisor Engine 7-E (paper delivery)
L-C4500-LIC=
Base product ID for electronically delivered software upgrade licenses
L-C4500E-LB-IP
LAN BASE to IP BASE upgrade license (electronically delivered)
L-C4500E-IP-ES
IP BASE to Enterprise Services upgrade license (electronically delivered)
L-C4500E-LB-ES
LAN BASE to Enterprise Services upgrade license (electronically delivered)
SD-X45-2GB-E
Cisco Catalyst 4500 2GB SD Memory Card for Sup 7-E
USB-X45-4GB-E
Cisco Catalyst 4500 4GB USB device for Sup 7-E
Licensing
Software Activation Licensing
Software activation licensing will be introduced to the Cisco Catalyst 4500E platform with the Supervisor 7-E. Each
Supervisor 7-E will ship with a universal image containing all feature sets, LAN Base, IP Base, and Enterprise
Services. The level of functionality is determined by the license applied.
Software activation licensing enables customers to:
●
Speed deployment and roll out new Cisco software activation feature sets across customers' global networks
●
Centrally and more accurately manage and track software and license compliance
●
Easily conduct software compliance audits to meet regulations without affecting network operations
Operational Simplicity:
●
Simplified upgrades and license transfers save time and improve productivity; you can add new capabilities
simply by using a license file
●
You can easily track software assets, licenses, and feature set status
●
A single software image improves service delivery
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 10 of 12
Data Sheet
Ease of Ordering:
●
"Try and buy" lets you use a temporary license to try and evaluate new Cisco IOS Software functionality
before purchase
●
Pay-as-you-grow software key enables new features incrementally without service calls
For more information about Cisco software licensing, visit http://www.cisco.com/go/sa.
Warranty
Cisco Catalyst 4500E Series and Cisco Catalyst 4500 switches are covered by the Cisco limited lifetime hardware
warranty. For more information, see http://www.cisco.com/en/US/docs/general/warranty/English/LH2DEN__.html.
Cisco Technical Support Services
Cisco Technical Support Services (Tables 7 and 8) help to ensure that your products from Cisco operate efficiently,
remain highly available, and benefit from current system software to assist you in effectively managing your network
service while controlling operational costs.
Cisco Technical Support Services provide significant benefits that go beyond what is offered under the Cisco
®
warranty policy. Services available under a Cisco SMARTnet service contract that are not covered under a warranty
include the following:
●
Latest software updates
●
Rapid replacement of hardware in next-day, 4-hour, or 2-hour dispatch options
●
Ongoing technical support through the Cisco Technical Assistance Center (TAC)
●
Registered access to http://www.cisco.com
Table 7.
Components of Cisco Technical Support Services
Service Feature Overview
Benefit or Advantage
Software Support
Software support offers maintenance and minor and major updates for licensed feature sets. Downloading
new maintenance releases, patches, or updates of Cisco IOS Software helps to enhance and extend the
useful life of Cisco devices. Through major software updates, it is possible to extend the life of equipment
and maximize application technology investments by:
● Adding new functions that, in many cases, require no additional hardware investment
● Increasing the performance of current functions
● Enhancing network or application availability, reliability, and stability
®
Cisco TAC Support
With more than 1000 highly trained customer support engineers, 390 CCIE experts, and access to 13,000
R&D engineers, Cisco TAC complements your in-house staff with a high level of knowledge in data, voice,
and video communications networking technology. Its sophisticated call-routing system quickly routes calls to
the correct technology personnel. The Cisco TAC is available 24 hours a day, 365 days a year.
Cisco.com
This award-winning Website provides 24-hour access to an extensive collection of online product and
technology information, interactive network management and troubleshooting tools, and knowledge-transfer
resources that can help customers reduce costs by increasing staff self-sufficiency and productivity.
Advance Replacement of Hardware
Advance Replacement and onsite field engineer options supply fast access to replacement hardware and
field resources for installing hardware, minimizing the risk of potential network downtime.
Table 8.
Cisco Technical Support Services: Competitive Differentiators
Service Feature Overview
Benefit or Advantage
Worldwide Virtual Lab
This extensive lab of Cisco equipment and Cisco IOS Software versions provides an invaluable engineering
resource and knowledge base for training, product information, and recreation and testing of selected
network problems to help decrease time to resolution.
Cisco TAC Training
● Boot camps
Cisco is committed to providing customers the latest in technology support. These TAC training programs
assist customers in case avoidance and provide knowledge transfer of Cisco networking expertise.
● Tech calls
● Tech forums
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 11 of 12
Data Sheet
Service Feature Overview
Benefit or Advantage
Cisco Live
A powerful suite of Internet-enabled tools with firewall-friendly features, these secure, encrypted Java applets
can turn a simple phone call into an interactive collaboration session, allowing a customer and Cisco TAC
support engineer to work together more effectively.
Global Logistics
This feature delivers award-winning, worldwide hardware-replacement support with 650 depots, covering 120
countries, at a $2.3 billion investment in inventory, taking advantage of 10,000 onsite field engineers.
Cisco IOS Software
Cisco IOS Software employs 100 discrete technologies with more than 2000 features. Each year 400 new
features are added. Cisco IOS Software is installed in more than 10 million devices and is running on more
than 10,000 networks worldwide. It operates on the world’s largest IPv6 and VoIP networks and in all major
service provider networks worldwide.
For More Information
To learn more about how you can take advantage of Cisco Technical Support Services, talk to your Cisco
representative or visit Cisco Technical Support Services at
http://www.cisco.com/en/US/products/svcs/ps3034/ps2827/serv_category_home.html.
For additional information about the Cisco Catalyst 4500, visit http://www.cisco.com/go/catalyst4500.
For additional information about Cisco products, contact:
●
United States and Canada: 800 553-NETS (6387)
●
Europe: 32 2 778 4242
●
Australia: 612 9935 4107
●
Other: 408 526-7209
●
http://www.cisco.com
Printed in USA
© 2010 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-612364-04
12/10
Page 12 of 12
ITEM 3
Data Sheet
Cisco Catalyst 4500E Series Power over Ethernet
Capabilities and Power Supplies
Power over Ethernet on the Cisco Catalyst 4500E Series Platform
®
®
The Cisco Catalyst 4500E Series platform offers line cards, power supplies, and accessories to support 15.4W
per port simultaneously on every port in any fully loaded Cisco Catalyst 4500E Series switch. Although all
references to “Power over Ethernet” (PoE), “inline power,” and “voice” power supply and line cards are
synonymous. There are four versions: Cisco prestandard PoE, 802.3af-compliant PoE, 802.3at-compliant PoEP
(30W), and Universal POEP (UPOE) (60W). Every Cisco Catalyst 4500 Series chassis and PoE power supply
supports the Cisco prestandard PoE, the IEEE 802.3af standard PoE, and IEEE 802.3at-compliant PoEP power
implementation, helping ensure backward compatibility with existing Cisco powered devices. PoEP is standard on
the Cisco Catalyst 4500E Series platform. UPOE requires Cisco Catalyst 4500E Series chassis.
All Cisco Catalyst 4500 Series PoE line cards can distinguish an IEEE or Cisco prestandard powered device from
an unpowered network interface card (NIC) to help ensure that power is applied only when an appropriate device
is connected. With a Cisco PoE network, administrators can depend on a robust network that is safe to deploy and
simple to maintain.
PoE(P)
PoE is the capability to provide up to 15.4W of power over 100m of standard Category 3 (or better) unshielded
twisted-pair (UTP) cables when an IEEE 802.3 af-compliant or Cisco prestandard powered device is attached to
the PoE line-card port. Instead of requiring wall power, attached devices such as IP phones, wireless base
stations, video cameras, and other IEEE-compliant appliances can use power provided from the Cisco Catalyst
4500 Series PoE line cards. This capability gives network administrators centralized control over power and
eliminates the need to install outlets in ceilings and other out-of-the-way places where a powered device can be
installed. When a switch is connected to an uninterruptible-power-supply (UPS) system, network administrators
can help ensure that power outages will not affect network availability. IEEE 802.3at-compliant PoEP extends the
Power over Ethernet capability to up to 30W over 100m of Category 5e (or better) unshielded twisted-pair (UTP)
cables.
UPOE
Universal POEP is an enhancement to the PoEP (802.3at) standard to allow powered devices up to 60W to
connect over a single Cat 5e cable. Standard PoEP uses only 2 twisted pairs (out of 4) in the Ethernet cable.
UPOE uses all 4 twisted pairs to deliver 60W to the port. The additional power UPOE offers over standard PoE
extends the advantages of PoE to next-generation powered workspace devices such as virtual desktop displays,
workgroup switches, and physical access controllers. All Cisco Catalyst 4500E Series UPOE line cards support
standard PoE as well as Cisco prestandard PoE. When deploying UPOE devices, Cat5e (or better) unshielded
twisted-pair (UTP) cable is recommended.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 1
Deploying PoE on the Cisco Catalyst 4500E Series
PoE deployment is extremely easy on the Cisco Catalyst 4500E Series platform. All Cisco Catalyst 4500 Series
PoE line cards automatically detect and power all attached powered devices. Moreover, the Cisco Catalyst 4500
Series returns unused port power to the system power budget for use by other devices because it supports the
IEEE 802.3af optional power classifications. Finer granularity for the budgeted power is achieved on Cisco power
devices that support Cisco Discovery Protocol.
The Cisco Catalyst 4500E Series offers internal power supplies and external power devices for multiple
deployment scenarios, including small and large deployments in AC or DC environments for data-only
configurations, and scalability up to 60W per port for PoE, PoEP, and UPOE configurations.
All the Cisco Catalyst E-Series Chassis models share a common power-supply form factor. Each Cisco Catalyst
4500 Series chassis is designed for 1 + 1 power protection while meeting the needs of PoE demands. In addition
to power resiliency, the Cisco Catalyst 4500 Series includes 1 + 1 supervisor-engine redundancy (Cisco Catalyst
4507R+E/4507R-E and 4510R+E/4510R-E models only) and software-based fault tolerance. Integrated resiliency
in both hardware and software minimizes network downtime, helping ensure workforce productivity, profitability,
and customer success.
Table 1 gives an overview of IEEE 802.3af power classifications.
Table 1.
Overview of IEEE 802.3af Power Classifications (Measured at the Switch Port)
IEEE 802.3 Class
Power Available at the Switch Port
0
15.4W: Default class
1
4W
2
7W
3
15.4W
4
Up to 30W via L2 negotiation (PoEP)
4 enhanced
Up to 60W via LLDP negotiation (UPOE)
Cisco prestandard PoE
6.3W
Comparison Between Cisco Prestandard PoE, 802.3af-Compliant PoE, and 802.3at-Compliant PoE
From a power perspective, there are several significant differences between the Cisco prestandard, 802.3afcompliant and 802.3at-compliant line cards. The differences are illustrated by comparing the total number of PoE
devices supported by the Cisco prestandard inline power line card, the 802.3 af-compliant, and the 802.3atcompliant line cards (Table 2).
Table 2.
Number of Powered Devices Supported When Using Power Supplies in a 1 + 1 Mode Using IEEE 802.3afCompliant Line Cards
Standard
802.3af Class 1
(4W per Port)
Standard
802.3af Class 2
(7W per Port)
Standard
802.3af Classes
0 and 3 (15.4W
per Port)
Standard
802.3at Class 4
(PoEP) (30W
per Port)
UPOE (60W per
port)
Cisco
Prestandard
(6.3W per Port)
1000 WAC
-
-
-
-
-
-
1400 WAC
-
-
-
-
-
-
1400 WDC
-
-
-
-
-
-
1400 WDC (triple input)
-
-
-
-
-
-
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 11
Standard
802.3af Class 1
(4W per Port)
Standard
802.3af Class 2
(7W per Port)
Standard
802.3af Classes
0 and 3 (15.4W
per Port)
Standard
802.3at Class 4
(PoEP) (30W
per Port)
UPOE (60W per
port)
Cisco
Prestandard
(6.3W per Port)
1300 WAC
186
106
48
24
12
118
2800 WAC
325
186
84
43
21
206
4200 WAC
384
384
223
114
57
384
6000 WAC
384
384
289
148
74
384
Cisco Catalyst 4500E Series Power-Supply Options: AC and DC
The Cisco Catalyst 4500E Series offers a variety of power supplies and accessories to meet the diverse needs of
enterprise and service provider customers. All available Cisco Catalyst 4500 Series power supplies can be used
for data-only deployments, which typically require just a few hundred watts. For deployments that dictate support
for PoE power, Cisco offers several options.
The Cisco Catalyst 4500E Series offers AC power with several internal supplies: 1000W (data only), 1400W (data
only), 1300W (data and PoE), 2800W (data and PoE), 4200W (data and PoE), and 6000W (data and PoE). When
5500W or less is required, the 4200W power supply can provide 5500W while protecting the chassis from a power
or power-supply subunit failure. All Cisco Catalyst 4500 AC power supplies are single phase and operate between
100VAC and 240VAC.
The Cisco Catalyst 4500E Series has two DC power options: one is optimized for data-only deployments in service
provider central offices (part number PWR-C45-1400DC), and the other is used for high-power PoE deployments
(PWR-C45-1400DC-P). All DC power supplies are designed to operate between -44VDC and -72VDC.
Cisco Catalyst 4500E Series Service Provider DC Power Supply
The triple-input 1400-WDC power supply is optimized for service provider central-office deployments. By providing
multiple inputs, the service provider DC power supply allows central-office technicians to customize the output
power to meet their application needs. Many central-office deployments require only a fraction of the 1400W
available in the service provider power supply. With low-current inputs, technicians can connect the supply to
smaller fuses and breakers. The service provider power supply makes it possible to deploy a Cisco Catalyst 3-slot
chassis with a single 15A circuit. Likewise, it is possible to deploy a fully populated Cisco Catalyst 10-slot chassis
with one 15A and two 20A circuits rather than a single 60A connection, which often requires rack rewiring
(Table 3).
Table 3.
Triple-Input 1400-WDC Power-Supply Input Modes
Input Mode
Input No.
Input Configuration
Maximum Total Output Power
1
1
One 12.5A
412W
2
2 or 3
One 15A
495W
3
1, 2, or 3
One 12.5A and one 15A
908W
4
2 or 3
Two 15A
990W
5
1, 2, or 3
One 12.5A and two 15A
1400W
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 11
Cisco Catalyst 4500E Series Dual Input AC PoE Power Supplies
The 6000W ACV and 4200W ACV power supplies feature combined Mode Power Resiliency as an extension of
the traditional combined mode power-supply behavior. Each power supply contains two smaller power supplies
(called subunits). In Combined Mode Power Resiliency the system relies only on power from three out of four
power-supply subunits. When using 200 VAC, this feature helps ensure that maximum power is available while the
switch is protected against a single input power failure or subunit component failure. (See Tables 4 through 7.)
6000W AC Power Supply
Table 4.
Dual-Input 6000 WAC Power-Supply Input Mode (Single Power Supply)
PS1-1
PS1-2
Total Output Power
110V
Off
1050W
110V
110V
2100W
220V
Off
3000W
220V
220V
6000W
Table 5.
Total Output Power in Combined Mode Power Resiliency
PS1-1
PS1-2
PS2-1
PS2-2
Total Output Power
110V
110V
110V
110V (hot standby)
2730W
220V
220V
220V
220V (hot standby)
7850W
6000W AC Power Supply also supports true output power consumption monitoring capability.
4200W AC Power Supply
Table 6.
Dual-Input 4200 WAC Power-Supply Input Mode (Single Power Supply)
PS1-1
PS1-2
Total Output Power
110V
Off
1050W
110V
110V
2100W
220V
Off
2100W
220V
220V
4200W
Table 7.
Total Output Power in Combined Mode Power Resiliency
PS1-1
PS1-2
PS2-1
PS2-2
Total Output Power
110V
110V
110V
110V (hot standby)
2730W
220V
220V
220V
220V (hot standby)
5500W
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 11
Cisco Catalyst 4500E Series Power Supplies
In any deployment scenario, whether AC or DC, the Cisco Catalyst 4500 Series has the power supplies and
external power devices to meet customers’ power needs for data, voice, and video applications (Figure 1).
Figure 1.
Cisco Catalyst 4500 Series Power Supplies
Features
For information on Cisco Catalyst 4500E Series power-supply specifications, see Tables 8 through 10.
Table 8.
Cisco Catalyst 4500E Series Power-Supply Specifications (Data-Only Power Supplies)
Power Supply
1000 WAC
(PWR C45-1000AC)
1400 WAC
(PWR C45-1400AC)
1400W Triple Input DC
(PWR-C45-1400DC)
Minimum Cisco IOS Software release
required
12.1(12c)EW
12.2(18)EW
12.2(25)EW
Minimum Cisco Catalyst Operating
System Software required
7.4(1)
-
-
Integrated PoE
No (data only)
No (data only)
No (data only)
IEEE 802.3af compliant
No
No
No
Input voltage
100 to 240 VAC (±10% for full
range)
100 to 240 VAC (±10% for full
range)
-48 to -60 VDC
Input current (rated)
12A at 100 VAC
5A at 240 VAC
16A at 100 VAC
7A at 240 VAC
Two -48 VDC at 15A
One -48 VDC at 12.5A
Output current (data)
12V at 83.4A
12V at 113.4A
Two -48 VDC at 15A
3.3V at 12.2A
3.3V at 12.2A
One -48 VDC at 12.5A
Output current (PoE)
-
-
-
Output power redundant mode (data)
1000W + 40W
1360W + 40W
1368W + 40W
®
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 11
Power Supply
1000 WAC
(PWR C45-1000AC)
1400 WAC
(PWR C45-1400AC)
1400W Triple Input DC
(PWR-C45-1400DC)
Output power redundant mode (PoE)
-
-
-
Output power combined mode (data)
1667W
2473W
2473W-
Output power combined mode (PoE)
-
-
-
Heat dissipation
943 BTU/hr
1048 BTU/hr
1048 BTU/hr
Holdup time
20 ms
20 ms
4 ms
Table 9.
Cisco Catalyst 4500E Series Power-Supply Specifications (Data and Voice)
1300 WACV
(PWR C45-1300ACV)
2800 WACV
(PWR C45 2800ACV)
1400 WDC-P
4200 WACV
(PWR C45-1400DC-P) (PWR C45-4200ACV)
6000 WACV
(PWR C45-6000ACV)
Minimum Cisco IOS
Software release
required
12.1(12c)EW
12.1(12c)EW
12.1(13)EW
12.2
12.2(52)SG
Minimum Cisco
Catalyst Operating
System Software
required
7.4(1)
7.4(1)
7.5(1)
-
-
Integrated PoE
Yes (up to 800W)
Yes (up to 1400W)
Up to 7500W (minus
power consumed for
data) when connected
directly to DC power
plant
Yes (up to 3855W)
Yes (up to 4800W)
IEEE 802.3af
compliant
Yes
Yes
Yes
Yes
Yes
Input voltage
100 to 240 VAC
(±10% for full range)
200 to 240 VAC
(±10% for full range)
Data: -48 to -60 VDC
100 to 240 VAC
(±10% for full range)
100 to 240 VAC
(±10% for full range)
16A at 100 VAC
16A at 200 VAC
Data: 31A at -60 VDC
Two 12A at 100 VAC
or
Two 12A at 100 VAC
or
Input current (rated)
7A at 240 VAC
Output current (data)
Output current (PoE)
Inline: -48 to -56 VDC
Inline: 180A at 48VDC
Two 12A at 200 VAC
Two 16A at 200 VAC
12V at 84.7A
12V at 113.3A
12V at 120A
12V at 115.3A
12V at 186.9A
3.3V at 12.5A
3.3V at 12.1A
3.3V at 10A
3.3V at 12.5A
3.3V at 12.5A
-50V at 16.7A
-50V at 28A
-48 or -60 VDC at
140A
-50V at 77.1A (200V)
-50V at 100.0A (200V)
-50V at 38A (100V)
-50V at 38.5A (120V)
Output power
redundant mode
(data)
1000W + 40W
1360W + 40W
1360W + 40W
1360W + 40W
2200W + 40W
Output power
redundant mode
(PoE)
800W maximum per
power supply
1400W maximum per
power supply
Up to 7500W (minus
the power consumed
for data)
3700W (220V)
4800W (220V)
1850W (110V)
1850W (110V)
Output power
combined mode
(data)
1667W
2473W
2473W
2473W
4400W
Output power
combined mode
(PoE)
1333W (maximum)
2333W
7280W
6700W (220V)
8700W (220V)
3360W (110V)
3360W (110V)
Heat dissipation
1568 BTU/hour
3580 BTU/hr
2720 BTU/hr
2387 BTU/hr
Data only: 1591
BTU/hr
Data and voice: 2905
BTU/hr
Holdup time
20 ms
20 ms
4 ms
20 ms
20 ms
Number of 802.3af
class 2 powered
devices supported in
redundant mode
106
186
384
384 (200V)
384 (200V)
245 (100V)
245 (100V)
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 11
Number of 802.3af
classes 0 and 3
powered devices
supported in the
redundant mode
Table 10.
1300 WACV
(PWR C45-1300ACV)
2800 WACV
(PWR C45 2800ACV)
1400 WDC-P
4200 WACV
(PWR C45-1400DC-P) (PWR C45-4200ACV)
6000 WACV
(PWR C45-6000ACV)
48
84
384
223 (200V)
289 (200V)
111 (100V)
111 (100V)
Specifications of Cisco Catalyst 4500E Series
Feature
Power-supply indicators and
interfaces
Description
● Fan cooling: Integrated in hot-inserting or hot-extraction unit
● Good: Green
● Fail: Red
● Support for Simple Network Management Protocol (SNMP) MIB
Environmental conditions
● Operating temperature: 32 to 104ºF (0 to 40ºC)
● Storage temperature: -40 to 167ºF (-40 to 75ºC)
● Relative humidity: 10 to 90 percent, noncondensing
● Operating altitude: -60 to 3000m
Regulatory Standards Compliance
Safety
● UL 60950
● CAN/CSA-C22.2 No. 60950
● EN 60950
● IEC 60950
● TS 001
● AS/NZS 3260
Electromagnetic
compatibility (EMC)
● FCC Part 15 (CFR 47) Class A
● ICES-003 Class A
● EN55022 Class A
● CISPR22 Class A
● AS/NZS 3548 Class A
● VCCI Class A
● EN 55022
● EN 55024
● EN 61000-6-1
● EN 50082-1
● EN 61000-3-2
● EN 61000-3-3
● ETS 300 386
Industry EMC, safety, and
environmental standards
● GR-63-Core Network Equipment Building Standards (NEBS) Level 3
● GR-1089-Core Level 3
● EN 50121-4
● ETS 300 019 Storage Class 1.1
● ETS 300 019 Transportation Class 2.3 (pending)
● ETS 300 019 Stationary Use Class 3.1
● ETS 300 386
Warranty
Cisco Catalyst 4500 Power Supplies are covered for five (5) years by the Cisco Limited Lifetime Hardware
Warranty. For more information, see this document on Cisco.com:
http://www.cisco.com/en/US/docs/general/warranty/English/LH2DEN__.html.
Note: If you purchased a Cisco Catalyst 4500E Series PoE line card or power supply before May 1, 2009, it is
covered by the Cisco 90-Day Limited Hardware Warranty. For more information, see this document on Cisco.com:
http://www.cisco.com/en/US/docs/general/warranty/English/901DEN__.html.
Service and support
Cisco offers lifecycle service and support for the Cisco Catalyst 4500 Series, directly and for resale through Cisco
distributors. From implementation to operation and optimization, Cisco offers advanced service and technical
support.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 11
Feature
Description
Advanced service
Cisco Total Implementation Solutions (TIS) offers a full range of implementation solutions, including project
management, project engineering, configuration, and staging and rollout coordination; Cisco TIS helps ensure
correct installation and deployment. For more information about Cisco TIS, visit:
http://www.cisco.com/en/US/partner/products/svcs/ps11/services_segment_category_home.html.
Technical support
Cisco SMARTnet Online and telephone support augments the customer’s operations-staff resources. Support
includes the ability to refresh system software at will as well as a range of Advance Replacement hardware
options. Cisco SMARTnet Onsite support adds the services of a field engineer, services that can be critical when
customer staffing is insufficient or unavailable for parts-replacement activities. For more information about Cisco
SMARTnet support, visit: http://www.cisco.com/en/US/partner/products/svcs/ps3034/serv_category_home.html.
ROHS compliance
ROHS5
®
Power and MTBF Information
Table 11 gives MTBF numbers for the different power supplies.
Table 11.
MTBF Numbers
Part Number
Rated MTBF (Hours)
PWR-C45-1300ACV
164,220
PWR-C45-2800ACV
155,822
PWR-C45-4200ACV
331,945
PWR-C45-6000ACV
341,356
PWR-C45-1400DC-P
316,454
PWR-C45-1000AC
250,000
PWR-C45-1400AC
570,530
PWR-C45-1400DC
316,454
Ordering Information
To place an order, visit the Cisco Ordering homepage or refer to Tables 12 through 14.
Table 12.
Cisco Catalyst 4500 Power-Supply Ordering Information
Part Number
Product Name
PWR-C45-1000AC
Cisco Catalyst 4500 1000 WAC Power Supply (Data Only)
PWR-C45-1400AC
Cisco Catalyst 4500 1400 WAC Power Supply (Data Only)
PWR-C45-1300ACV
Cisco Catalyst 4500 1300 WAC Power Supply (PoE)
PWR-C45-2800ACV
Cisco Catalyst 4500 2800 WAC Power Supply (PoE)
PWR-C45-1400DC-P
Cisco Catalyst 4500 1400 WDC Power Supply with PEM (PoE)
PWR-C45-4200ACV
Cisco Catalyst 4500 4200 WAC Power Supply (PoE)
PWR-C45-6000ACV
Cisco Catalyst 4500 6000 WAC Power Supply (PoE)
PWR-C45-1400DC
Cisco Catalyst 4500 1400 WDC SP Central-Office Power Supply (Triple Input)
Table 13.
Cisco Catalyst 4500 Series Power-Cord Options (Data Only)
Power Supply
1000 WAC
1400 WAC
1400 WDC
Region/Product ID
PWR-C45-1000AC
PWR-C45-1400AC
-
Europe
CAB-7KACE=
CAB-7513ACE=
-
International
-
-
-
United States
CAB-7KAC=
CAB-7513AC=
-
Australia
CAB-7KACA=
CAB-7513ACA=
-
Italy
CAB-7KACI=
CAB-7513ACI=
-
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 11
Power Supply
1000 WAC
1400 WAC
1400 WDC
United Kingdom
CAB-7KACU=
CAB-7513ACU=
-
Argentina
CAB-7KACR=
CAB-7513ACR=
-
South Africa
-
CAB-7513ACSA=
-
Table 14.
Cisco Catalyst 4500 Series Power-Cord Options (Data and Voice)
Power Supply
1300 ACV
2800 WACV
4200 WACV
6000 WACV
1400 WDC-P
External Power
Region and
product ID
PWR C45
1300ACV
PWR C45
2800ACV
PWR C454200ACV
PWR C456000ACV
PWR C451400DC-P
2500W PWR-4502
Europe
CAB-7513ACE=
CAB-AC-2800WEU=
CAB-CEE77-C19EU
CAB-CEE77-C19EU
-
CAB-4502AC-EU
International
N/A
CAB-AC-2800WINT=
CAB-I309-C19-INT
CAB-I309-C19-INT
-
-
United States
CAB-7513AC=
CAB-AC-2800WTWLK=
CAB-US515PC19-US
CAB-US515PC19-US
-
CAB-4502AC-US
CAB-AC-2800W-6- CAB-L620P-C1920=
US
*
CAB-L620P-C19US
CAB-US620PC19-US
CAB-US620PC19-US
Australia
CAB-7513ACA=
Same as
international
CAB-A3112-C19AUS
CAB-A3112-C19AUS
-
-
Italy
CAB-7513ACI=
Same as
international
CAB-C2316-C19IT
CAB-C2316-C19IT
-
-
Argentina
CAB-7513ACR=
Same as
international
Same as
international
Same as
international
-
-
South Africa
CAB-7513ACSA=
Same as
international
Same as
international
Same as
international
-
-
Israel
-
-
CAB-S132-C19ISRL
CAB-S132-C19ISRL
-
-
The 1300-WACV and 1400-WAC power supplies can use the power cords for the 2800-WAC power supply.
Cisco Limited Lifetime Hardware Warranty
The Cisco limited lifetime hardware warranty (LLW) includes 10-day advance hardware replacement for as long as
the original end user owns the product. Table 15 describes the limited lifetime hardware warranty.
Your formal warranty statement, including the warranty applicable to Cisco software, appears in the Cisco
information packet that accompanies your Cisco product. We encourage you to review carefully the warranty
statement shipped with your specific product before use.
For additional information on warranty terms, visit http://www.cisco.com/go/warranty.
Adding a Cisco technical services contract to your device coverage provides benefits not available with warranty
including access to the Cisco Technical Assistance Center (TAC), a variety of hardware replacement options to
meet critical business needs, updates for licensed Cisco IOS Software, and registered access to the extensive
Cisco.com knowledge base and support tools. Table 16 describes the benefits and features of Cisco technical
services.
For information about Cisco Technical Services, go to http://www.cisco.com/go/ts.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 11
Table 15.
Limited Lifetime Hardware Warranty
1
Cisco Limited Lifetime Hardware Warranty
Warranty Duration
As long as the original end user continues to own or use the product except for the fan and power supply, which are
limited to 5 years.
EoL Policy
In the event of discontinuance of product manufacture, Cisco warranty support is limited to 5 years from the
announcement of discontinuance.
Hardware Replacement
Cisco or its service center will use commercially reasonable efforts to ship a replacement part within 10 business days
after receipt of the RMA request and confirmation that a replacement part is appropriate response. Actual delivery
times may vary depending on customer location.
Effective Date
Hardware warranty commences from the date of shipment to the customer (and in case of resale by a Cisco reseller,
not more than 90 days after original shipment by Cisco).
TAC Support
None.
Cisco.com Access
Warranty allows guest access only to Cisco.com.
1
Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.
Cisco and Partner Services
Enable the innovative, secure, intelligent edge in the Borderless Network Architecture using personalized services
from Cisco and our partners. Through a discovery process that begins with understanding your business
objectives, we help you integrate the next-generation Cisco Catalyst 4500-E Series Switches into your architecture
and incorporate network services onto that platform. Sharing knowledge and leading practices, we support your
success every step of the way as you deploy, absorb, manage, and scale new technology. Choose from a flexible
suite of support services designed to meet your business needs and help you maintain high-quality network
performance while controlling operational costs. Table 16 shows the Cisco technical services available for Cisco
Catalyst 4500-E Series Switches.
For additional information about Cisco services, visit http://www.cisco.com/go/services.
Table 16.
Cisco Technical Services for Cisco Catalyst 4500-E Series Switches
Technical Services
Cisco SMARTnet Service
● Around-the-clock, global access to the Cisco Technical Assistance Center (TAC)
● Unrestricted access to the extensive Cisco.com resources, communities, and tools
● Next-business-day, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement2 and onsite parts replacement and installation available
● Ongoing operating system software updates within the licensed feature set1
● Proactive diagnostics and real-time alerts on Smart Call Home enabled devices
Cisco Smart Foundation Service
● Next business day advance hardware replacement as available
● Business hours access to SMB TAC (access levels vary by region)
● Access to Cisco.com SMB knowledge base
● Online technical resources through Smart Foundation Portal
● Operating system software bug fixes and patches
Cisco Focused Technical Support Services
Three levels of premium, high-touch services are available:
● Cisco High-Touch Operations Management Service
● Cisco High-Touch Technical Support Service
● Cisco High-Touch Engineering Service
Valid Cisco SMARTnet or SP Base contracts on all network equipment are required.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 10 of 11
Notes:
1.
Cisco operating system updates include the following: maintenance releases, minor updates, and major updates within the
licensed feature set.
2.
Advance hardware replacement is available in various service-level combinations. For example, 8x5xNBD indicates that
shipment will be initiated during the standard 8-hour business day, 5 days a week (the generally accepted business days within
the relevant region), with next business day (NBD) delivery. Where NBD is not available, same day ship is provided. Restrictions
apply; please review the appropriate service descriptions for details.
Printed in USA
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-608944-06
01/12
Page 11 of 11
ITEM 4
Data Sheet
Cisco Catalyst 4500 Series Line Cards
High-Performance, Mobile, and Secure User Experience
Product Benefits
®
®
Cisco Catalyst 4500 Series Switches enable borderless networks, providing high-performance, mobile, and
secure user experiences through Layer 2-4 switching. Enabling security, mobility, application performance, video,
and energy savings over your network infrastructure, the Cisco Catalyst 4500 Switch supports resiliency,
virtualization, and automation, further improving the ease of network use. Cisco Catalyst 4500 Series Switches
provide borderless performance, scalability, and services with reduced total cost of ownership (TCO) and superior
investment protection.
The Cisco Catalyst 4500 Switch delivers predictable and scalable high performance, with advanced dynamic
quality of service (QoS) capabilities and configuration flexibility for deploying borderless networks. Integrated
resiliency features in both hardware and software maximize network availability, helping to ensure workforce
productivity, profitability, and customer success. Its centralized, innovative, and flexible system design helps
ensure smooth migration to wire-speed IPv6 and 10 Gigabit Ethernet (GE). The forward and backward
compatibility between generations of the Cisco Catalyst 4500 Series extends deployment life, providing
exceptional investment protection, while reducing the (TCO).
The Cisco Catalyst 4500E Series is a high-performance, next-generation extension to the Cisco Catalyst 4500
Series. The new E-Series is composed of the Cisco Catalyst 4500E Series supervisor engines, E-Series line
cards, and E-Series chassis, which are designed for a high-performance, mobile, and secure user experience with
superior backward and forward compatibility, delivering exceptional investment protection for organizations of all
sizes.
Cisco Catalyst 4500E Series and Classic Line Cards
The Cisco Catalyst 4500 Series offers two classes of line cards: classic and E-Series. Classic line cards provide
6 gigabits of switching capacity per slot. E-Series line cards provide increased switching capacity per slot. This
increase in per-slot switching capacity with the E-Series line cards requires the Cisco Catalyst 4500E Series
chassis and the Cisco Catalyst 4500E Series Supervisor. Two types of E-Series line cards are available based on
the per-slot switching capacity. E-Series line cards numbered 47xx operate at 48 gigabits per slot, while E-Series
line cards numbered 46xx operate at 24 gigabits per slot. Classic line cards may be deployed in both classic and
E-Series chassis with either classic Cisco Catalyst 4500 Series supervisor engines or with the Cisco Catalyst
4500E Series Supervisor Engine. With the E-Series supervisor engine, the per-slot switching capacity for classic
line cards remains at 6 gigabits per slot. However, because of the centralized switching architecture of the Cisco
Catalyst 4500, the classic line cards will adopt all of the new E-Series supervisor engine features such as eight
queues per port, dynamic QoS, and hardware-based IPv6 routing. For more feature details, refer to the E-Series
supervisor engine data sheet. Classic line cards and E-Series line cards may be mixed and matched within a
Cisco Catalyst 4500E Series chassis with no performance degradation: classic line cards will operate at 6 gigabits
per slot, and E-Series line cards operate at either 48 gigabits per slot or 24 gigabits per slot based on whether
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 22
they belong to the 47xx or 46xx family of line cards. Table 1 summarizes the chassis and supervisor support for
both classic and E-Series line cards.
Table 1.
Cisco Catalyst 4500 Line-Card Support Options
Line-Card Type
Per-Slot Bandwidth
Chassis Support
Supervisor Support
Cisco Catalyst 4500 47xx
E-Series Line Cards
48 Gbps
Cisco Catalyst 4503-E, 4506-E,
4507R+E, and 4510R+E
Supervisor Engine 7-E,
24 Gbps
Cisco Catalyst 4507R-E and
4510R-E
Supervisor Engine 7-E,
Cisco Catalyst 4503-E, 4506-E,
4507R-E, 4507R+E, 4510R-E, and
2
4510R+E
Supervisor Engine 7-E,
WS-X4748-RJ45V+E
1
WS-X4748-UPOE+E
Supervisor Engine 7L-E
Supervisor Engine 7L-E
WS-X4748-RJ45-E
Cisco Catalyst 4500 46xx
E-Series Line Cards
24 Gbps
Supervisor Engine 7L-E,
Supervisor Engine 6-E,
Supervisor Engine 6L-E
Cisco Catalyst 4500 Series
Classic Line Cards
6 Gbps
Cisco Catalyst 4503, 4506, 4507R,
and 4510R Switches
Supervisor Engine 7-E3,
Cisco Catalyst 4503-E, 4506-E,
4507R-E, 4507R+E, 4510R-E, and
4510R+E Switches
Supervisor Engine 6-E,
Supervisor Engine 7L-E,
Supervisor Engine 6L-E3,
Supervisor Engine V-10GE
Power over Ethernet on Cisco Catalyst 4500E
The Cisco Catalyst 4500E Series offers line cards, power supplies, and accessories required to deploy and
operate standards-based Power over Ethernet/Power over Ethernet Plus (PoE/PoEP) and Universal POEP
(UPOE). PoE provides power over 100 m of standard unshielded twisted-pair (UTP) cables when an IEEE
802.3af/at-compliant or Cisco pre-standard powered device is attached to the PoE/PoEP and UPOE line-card port.
Instead of requiring wall power, attached devices such as IP phones, wireless base stations, video cameras, and
other IEEE-compliant appliances can use power provided from the Cisco Catalyst 4500 Series PoE/PoEP and
UPOE line cards. For the regular DC (Direct Current) device that doesn't support PoE/PoEP natively, Cisco
Catalyst 4500 Series provides the UPOE Power Splitter that enables an UPOE port to power a 12V DC power
device and another PoE/PoEP appliance. This capability gives network administrators centralized control over
power and eliminates the need to install outlets in ceilings and other out-of-the-way places where a powered
device can be installed. Table 2 shows the PoE options for Cisco Catalyst 4500 Series line cards.
Although all references to “PoE/PoEP/UPOE,” “inline power,” and “voice” power supplies and line cards are
synonymous, there are currently four versions: Cisco prestandard, IEEE 802.3af compliant, IEEE 802.3at
compliant, and UPOE. Every Cisco Catalyst 4500 Series chassis and PoE power supply supports the IEEE
802.3af/at standard and the Cisco prestandard power implementation, helping ensure backward compatibility with
existing devices powered by Cisco. UPOE line cards require E series chassis. All IEEE 802.3af/at-compliant and
UPOE line cards can distinguish an IEEE or Cisco prestandard powered device from an unpowered network
interface card (NIC), helping ensure power is applied only when an appropriate device is connected.
1
WS-X4712-SFP+E is not supported on 4507R-E and 4510R-E chassis.
Slots 8-10 on 4510R-E and 4510R+E chassis do not support E-Series line cards with Supervisor Engine 6-E.
3
Supervisor Engine 7-E does not support non-E-Series chassis: 4503, 4506, 4507R, and 4510R.
2
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 22
Cisco Catalyst 4500E Series and Classic Gigabit Ethernet Copper Line Cards
The Cisco Catalyst 4500E Series 48-port Gigabit Ethernet line cards provide high-performance 10/100/1000
switching. Two types of E-Series line cards are available, based on the per-slot bandwidth: 47xx line cards that
drive 48 Gbps per slot, and 46xx line cards that drive 24 Gbps per slot. The Cisco Catalyst 4500 48-port
10/100/1000 PoEP E-Series 47xx line card provides standard IEEE 802.3at PoEP support on all 48 ports
™
simultaneously. All series 47xx line cards support standard IEEE 802.1AE encryption and Cisco TrustSec in
hardware. The Cisco Catalyst 4500 48-port 10/100/1000 line cards are available in four versions: Data Only, PoE,
PoEP, and UPOE.
Table 2.
Cisco Catalyst 4500 Line Card PoE Options
Line-Card Type
Data Only (no PoE)
PoE (802.3af)
PoEP (802.3at)
UPOE
Cisco Catalyst 4500 47xx E-Series Line Cards
Yes
Yes
Yes
Yes
Cisco Catalyst 4500 46xx E-Series Line Cards
Yes
Yes
Yes
-
Cisco Catalyst 4500 Series Classic Line Cards
Yes
Yes
Yes
-
Cisco Catalyst 4500 Classic Fast Ethernet Copper Line Cards
The Cisco Catalyst 4500 Series offers a variety of classic Fast Ethernet line cards with copper interfaces optimized
for desktops and servers for enterprise and commercial switching solutions. The two varieties of fast Ethernet
copper line cards are:
●
Data only (no PoE)
●
Standard IEEE 802.3af PoE
Cisco Catalyst 4500E Series 10 Gigabit Ethernet Fiber Line Cards
The Cisco Catalyst 4500E Series supports 10 Gigabit Ethernet Fiber line cards.
The Cisco Catalyst 4500E Series 12-port 10 Gigabit Ethernet line card (2.5:1 oversubscribed) can be deployed for
high-performance and high-density 10 Gigabit Ethernet aggregation in the campus and in small to medium-sized
networks as a core switch. The Cisco Catalyst 4500E Series 12-port 10 Gigabit Ethernet line card supports
standard Small Form-Factor Pluggable Plus (SFP+) optics. The ports can be used interchangeably as Gigabit
Ethernet and 10 Gigabit Ethernet to support phased migration from Gigabit Ethernet to 10 Gigabit Ethernet.
The Cisco Catalyst 4500E Series 6-port 10 Gigabit Ethernet line card (2.5:1 oversubscribed) can be deployed for
high-performance/low-density 10 Gigabit Ethernet aggregation in the campus, in small to medium-sized networks
as a core switch, or for high-performance wiring closets where additional 10 Gigabit Ethernet uplinks are required.
The Cisco Catalyst 4500E Series 6-port 10 Gigabit Ethernet line card supports standard X2 optics as well as the
Cisco TwinGig modules. The Cisco TwinGig Converter Module converts a single 10 Gigabit Ethernet X2 interface
into two Gigabit Ethernet port slots, which can be populated with appropriate SFP optics, providing a total of 12
wire-speed Gigabit Ethernet ports if used in all six X2 interface slots. The flexibility provided by the TwinGig
Converter Module enables customers to aggregate Gigabit Ethernet and 10 Gigabit Ethernet LAN access switches
on a single line card and also supports phased migration from Gigabit Ethernet to 10 Gigabit Ethernet. This
capability further demonstrates the flexibility and the investment protection of the Cisco Catalyst 4500 Series
architecture (Figure 1).
TwinGig modules convert a single X2 port into two Gigabit Ethernet SFP ports.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 22
Figure 1.
TwinGig Module
Cisco Catalyst 4500E Series Gigabit Ethernet Fiber Line Cards
The Cisco Catalyst 4500E Series 24-port Gigabit Ethernet fiber line card (SFP based) and Cisco Catalyst 4500E
Series 12-port Gigabit Ethernet fiber line card (SFP based) provide high-performance switching at 24 Gbps per
slot (line rate). Both E-Series line cards are nonblocking and designed for high-performance 1 Gigabit Ethernet
aggregation in the campus and to support Fiber to the Desktop (FTTD) applications.
The Cisco Catalyst 4500 Series offers oversubscribed Gigabit Ethernet fiber line cards optimized for FTTD and
FTTH deployments. The Cisco Catalyst 4500 Series 48 module Gigabit line card (8:1 oversubscribed) provides
switching at 6Gbps per slot and can be used for higher density deployments.
The Cisco Catalyst 4500E Series 40 module Gigabit line card (2:1 oversubscribed) provides switching at 24Gbps
per slot and can be used for enterprise deployments that require higher density and lower oversubscription. This
line card also supports a specialized BX optics (compact SFP) that doubles the density to 80 ports per line card
using 40 module, making it attractive for the FTTH deployment. The CSFP is a dual bidirectional SFP type that
has the same form factor as a regular SFP, but can support 2 users that use BX type of optics (Figure 2)
Figure 2.
Compact SFP
Cisco Catalyst 4500 Classic Fast Ethernet Fiber Line Cards
The Cisco Catalyst 4500 Series offers a variety of classic Fast Ethernet line cards with fiber interfaces optimized
for desktops, branch office backbones, and servers for enterprise and commercial switching solutions and service
provider metropolitan Ethernet networks. Fast Ethernet line cards include various densities of wire-speed 10/100,
100-FX, 100BASE-LX10, and 100BASE-BX-D options.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 22
Features and Benefits
Functional Transparency
Cisco Catalyst 4500 Series Switches offer an extensive line of modules that support numerous speeds and
physical media combinations. These line cards are functionally transparent; all the packet processing, queuing,
buffering, and QoS occur in the supervisor engine. To that end, both classic and E-Series line cards acquire the
features and capabilities of the installed supervisor engine. For example, a classic line card previously deployed
with a classic supervisor engine using four queues per port will automatically have capability for eight queues per
port if redeployed with a Supervisor Engine 7-E/6-E. This architecture enables customers to easily upgrade all
Ethernet line cards on their Cisco Catalyst 4500 Series systems to higher layer switching functions by adding a
new supervisor engine. The simple design of the line cards results in a very high mean time between failures
(MTBF), helping ensure high availability for a single connection to an end user.
Modular Versatility
The Cisco Catalyst 4500 Series is a centralized architecture that is designed to provide dedicated wire-speed
bandwidth to each line-card slot within the chassis. Each line card has a dedicated bandwidth to the supervisor
engine for packet processing. All network data that flows into the Cisco Catalyst 4500 Series through the various
line cards goes through the supervisor engine for processing, even in single-slot port-to-port communications. All
line cards have some per-slot bandwidth that allows network administrators to design a system that offers full
dedicated bandwidth-to-server and switch-to-switch applications and still provides high performance over
subscribed gigabit to the desktop.
A modular centralized design allows customers to use their investment in high-performance line cards across the
entire line of Cisco Catalyst 4500 Series chassis and supervisor engines. For example, line cards that shipped
with the original Cisco Catalyst 4003 Switch in 1999 will work in the Cisco Catalyst 4500E Series chassis.
Because of the centralized architecture of the Cisco Catalyst 4500, all line cards deployed in a chassis benefit
from the enhanced features that the supervisor engine provides, including QoS, Layer 2/3/4 routing, and
hardware-based IPv6.
Following are descriptions of line cards that are available for Cisco Catalyst 4500 Series Switches.
Cisco Catalyst 4500E Series 10 Gigabit Ethernet Fiber Line Card
Figure 3 shows the WS-X4712-SFP+E.
Figure 3.
WS-X4712-SFP+E Cisco Catalyst 4500E Series 12-Port 10 Gigabit Ethernet (SFP+)
WS-X4712-SFP+E:
●
48 gigabits per-slot capacity
●
Bandwidth is allocated across four 3-port groups, providing 12 Gbps per port group (2.5:1)
●
Up to 12 ports 10GE SFP+ (10GBASE-R) or 12 ports GE SFP (1GBASE-X)
●
SFP+ and SFP can be used simultaneously on the same line card without any restrictions
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 22
●
Cisco IOS XE Release 3.1.0SG or later
●
IEEE 802.1AE and Cisco TrustSec capability in hardware
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Enterprise and commercial: designed for high-speed backbone and switch-to-switch applications
●
Service provider: 10GE/GE mix aggregation for DSLAM/PON/mobile data backhaul
●
WS-X4712-SFP+E is not supported on 4507R-E and 4510R-E chassis
Figure 4 shows the WS-X4606-X2-E.
Figure 4.
WS-X4606-X2-E Cisco Catalyst 4500E Series 6-Port 10 Gigabit Ethernet (X2)
WS-X4606-X2-E:
●
24 gigabits per-slot capacity
●
24-gigabit bandwidth is allocated across six 10 Gigabit Ethernet ports (2.5:1)
●
10GBASE-X (X2) and 1GBASE-X (SFP)
●
Up to 6 ports 10GE X2 or 12 ports GE SFP using TwinGig Converter Module
●
TwinGig modules must be used in groups of three: ports 1-3 or ports 4-6
●
Cisco IOS Software Release 12.2(40)SG or later
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Enterprise and commercial: designed for high-speed backbone and switch-to-switch applications
●
Service provider: 10GE/GE mix aggregation for DSLAM/PON/mobile data backhaul
Cisco Catalyst 4500E Series Gigabit Ethernet Fiber Line Card
Figure 5shows the WS-X4624-SFP-E.
Figure 5.
WS-X4624-SFP-E
WS-X4624-SFP-E:
●
24-port line-rate SFP line card, providing 24 gigabits per-slot capacity (1:1 oversubscribed)
●
Cisco IOS Software Release 12.2(44)SG or later
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Inherits Supervisor Engine QoS capability
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 22
●
Compatible only with E-Series supervisor engines
●
Enterprise, mid-market, and commercial core and distribution deployments requiring line-rate capability
●
Service provider: GE aggregation for DSLAM/PON/mobile data backhaul
Figure 6 shows the WS-X4612-SFP-E.
Figure 6.
WS-X4612-SFP-E
WS-X4612-SFP-E:
●
12 Port line-rate SFP line card, providing 12 gigabits per-slot capacity (1:1 oversubscribed)
●
Cisco IOS Software Release 12.2(54)SG or later
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Inherits Supervisor Engine QoS capability
●
Compatible only with E-Series supervisor engines
●
Enterprise, mid-market, and commercial core and distribution deployments requiring line-rate capability
●
Service provider: GE aggregation for DSLAM/PON/mobile data backhaul
Figure 7 shows WS-X4640-CSFP-E.
Figure 7.
WS-X4640-CSFP-E
WS-X4640-CSFP-E:
●
40 modules of Gigabit SFP line card (1000BaseX), providing 24 gigabits per-slot capacity (SFP optional)
●
40 ports with Gigabit SFP (2:1 oversubscribed)
●
80 ports with Gigabit compact SFP (4:1 oversubscribed)
●
Customers can mix and match Gigabit SFP and Gigabit compact SFPs
●
Cisco IOS Software Release IOS XE 3.2.0 SG or later
●
Compatible with Supervisor Engine 7E and 7L-E only
●
Supported on 3, 6, and 7 slot chassis
●
IEEE 802.3, IEEE 802.3ah, IEEE 802.3x flow control
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Inherits supervisor engine QoS capability
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 22
●
Service Provider: Point-to-Point fiber to the home (FTTH) or building (FTTB) for residential and business
applications
●
Enterprise: Providing Fiber to the Desktop (FTTD), for deployments where non-blocking is not a mandatory
requirement
Cisco Catalyst 4500E Series 10/100/1000 Line Cards
Figure 8 shows the WS-X4748-UPOE+E.
Figure 8.
WS-X4748-UPOE+E Cisco Catalyst 4500E Series 48-Port 802.3af PoE, 802.3at PoEP, and UPOE 10/100/1000
(RJ-45)
WS-X4748-UPOE+E:
●
48 ports nonblocking
●
10/100/1000 module (RJ-45)
●
Cisco IOS XE Release 3.1.0SG or later
●
UPOE: capable of up to 60 W per port up to 1440 W
●
Energy Efficient Ethernet 802.3az
●
IEEE 802.3af/at and Cisco prestandard PoE, IEEE 802.3x flow control
●
IEEE 802.1AE and Cisco TrustSec capability in hardware
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Capable of up to 30 W of inline power per port on all ports simultaneously
●
Enterprise and commercial: designed to power next-generation IP phones, wireless base stations, video
cameras, virtual desktop clients, and other PoE/UPOE devices
●
Campus and branch applications requiring enhanced performance for large file transfers and network
backups
Figure 9 shows the WS-UPOE-12VPSPL.
Figure 9.
WS-UPOE-12VPSPL Cisco Power Splitter
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 22
WS-UPOE-12VPSPL:
●
Receives both data and power from an UPOE (RJ45) connector
●
Regular 12V DC connector
●
10/100/1000 RJ45 PoE/PoEP connector
●
Provide integrated solution to PoE and regular DC power device from a single source
Figure 10 shows the WS-X4748-RJ45V+E.
Figure 10.
WS-X4748-RJ45V+E Cisco Catalyst 4500E Series 48-Port 802.3af PoE and 802.3at PoEP 10/100/1000 (RJ-45)
WS-X4748-RJ45V+E:
●
48 ports nonblocking
●
10/100/1000 module (RJ-45)
●
Cisco IOS XE Release 3.1.0SG or later
●
IEEE 802.3af/at and Cisco prestandard PoE, IEEE 802.3x flow control
●
IEEE 802.1AE and Cisco TrustSec capability in hardware
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Capable of up to 30 W of inline power per port on all ports simultaneously
●
Enterprise and commercial: designed to power next-generation IP phones, wireless base stations, video
cameras, and other PoE devices
●
Campus and branch applications requiring enhanced performance for large file transfers and network
backups
Figure 11 shows the WS-X4748-RJ45-E.
Figure 11.
WS-X4748-RJ45-E Cisco Catalyst 4500E Series 48-Port 10/100/1000 (RJ-45)
WS-X4748-RJ45-E:
●
48 ports nonblocking
●
10/100/1000 module (RJ-45)
●
Cisco IOS XE Release 3.1.0SG or later
●
Energy Efficient Ethernet 802.3az
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 22
●
IEEE 802.1AE and Cisco TrustSec capability in hardware
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Enterprise and commercial: designed for data only user access
●
Campus and branch applications requiring enhanced performance for large file transfers and network
backups
Figure 12 shows the WS-X4648-RJ45V+E.
Figure 12.
WS-X4648-RJ45V+E Cisco Catalyst 4500E Series 48-Port 802.3af PoE and 802.3at PoEP 10/100/1000 (RJ-45)
WS-X4648-RJ45V+E:
●
24 gigabits per-slot capacity
●
48 ports
●
10/100/1000 module (RJ-45)
●
Cisco IOS Software Release 12.2(40)SG or later
●
IEEE 802.3af/at and Cisco prestandard PoE, IEEE 802.3x flow control
●
Bandwidth is allocated across eight 6-port groups, providing 3 Gbps per port group (2:1)
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Capable of up to 30 W of inline power per port on up to 24 ports simultaneously
●
Enterprise and commercial: designed to power next-generation IP phones, wireless base stations, video
cameras, and other PoE devices
●
Campus and branch applications requiring enhanced performance for large file transfers and network
backups
Figure 13 shows the WS-X4648-RJ45V-E.
Figure 13.
WS-X4648-RJ45V-E Cisco Catalyst 4500E Series 48-Port 802.3af PoE 10/100/1000 (RJ-45)
WS-X4648-RJ45V-E:
●
24 gigabits per-slot capacity
●
48 ports
●
10/100/1000 module (RJ-45)
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 10 of 22
●
Cisco IOS Software Release 12.2(40)SG or later
●
Bandwidth is allocated across eight 6-port groups, providing 3 Gbps per port group (2:1)
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
IEEE 802.3af and Cisco prestandard PoE, IEEE 802.3x flow control
●
Enterprise and commercial: designed to power IP phones, wireless base stations, video cameras, and
other IEEE-compliant powered devices
●
Campus and branch applications requiring enhanced performance for large file transfers and network
backups
Figure 14 shows the WS-X4648-RJ45-E.
Figure 14.
WS-X4648-RJ45-E Cisco Catalyst 4500E Series 48-Port Data-only 10/100/1000 (RJ-45)
WS-X4648-RJ45-E:
●
24 gigabits per-slot capacity
●
48 ports
●
10/100/1000 module (RJ-45)
●
Cisco IOS Software Release 12.2(50)SG or later
●
Bandwidth is allocated across eight 6-port groups, providing 3 Gbps per port group (2:1)
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Enterprise campus, commercial collapsed core, and branch applications requiring enhanced performance
for large file transfers and network backups
●
Campus and branch applications requiring enhanced performance for large file transfers and network
backups
●
Service provider: GE/100M aggregation for DSLAM and PON
Cisco Catalyst 4500 Classic Line Cards
Classic 10/100/1000 Ethernet Line Cards
Figure 15 shows the WS-X4548-RJ45V+.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 11 of 22
Figure 15.
WS-X4548-RJ45V+ Cisco Catalyst 4500 48-Port 802.3af PoE and 802.3at PoEP 10/100/1000 (RJ-45)
WS-X4548-RJ45V+:
●
48 ports
●
10/100/1000 (RJ-45)
●
Cisco IOS Software Release 12.2(50)SG or later
●
IEEE 802.3af/at and Cisco prestandard PoE, IEEE 802.3x flow control
●
Bandwidth is allocated across six 8-port groups, providing 1 Gbps per port group
●
Capable of up to 30 W of inline power per port on up to 24 ports simultaneously
●
Enterprise and commercial: designed to power next-generation IP phones, wireless base stations, video
cameras, and other PoE devices that require power up to 30 watts
Figure 16 shows the WS-X4548-GB-RJ45V.
Figure 16.
WS-X4548-GB-RJ45V Cisco Catalyst 4500 PoE IEEE 802.3af 10/100/1000, 48 Ports (RJ-45)
WS-X4548-GB-RJ45V:
●
48 ports
●
10/100/1000 (RJ-45)
●
Cisco IOS Software Release 12.2(18)EW or later
●
IEEE 802.3af and Cisco prestandard PoE, IEEE 802.3x flow control
●
Bandwidth is allocated across six 8-port groups, providing 1 Gbps per port group
●
Enterprise and commercial: designed to power IP phones, wireless base stations, video cameras, and
other IEEE-compliant powered devices
Figure 17 shows the WS-X4548-GB-RJ45.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 12 of 22
Figure 17.
WS-X4548-GB-RJ45 Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45)
WS-X4548-GB-RJ45:
●
48 ports
●
10/100/1000 module (RJ-45)
●
Cisco IOS Software Release 12.1(19)EW or later
●
IEEE 802.3x flow control
●
Bandwidth is allocated across six 8-port groups, providing 1 Gbps per port group
●
Enterprise and commercial: designed for gigabit to the desktop
Classic Gigabit Ethernet Fiber Line Card (GBIC or SFP)
The Cisco Catalyst 4500 Series offers a variety of gigabit interface converter (GBIC) - or Small Form Factor
Pluggable (SFP)-enabled gigabit solutions for high-performance Gigabit Ethernet uplinks and server farm
connectivity. The five GBIC- or SFP-enabled gigabit line-card options for the Cisco Catalyst 4500 Series include 6, 18-, and 48-port versions. GBIC or SFP technology allows customers to intermix intrabuilding multimode fiber
(MMF) connections and long-distance single-mode connections simply by changing the GBIC or SFP type.
(See Table 3 for more information.)
Figure 18 shows the WS-X4306-GB.
Figure 18.
WS-X4306-GB Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC)
WS-X4306-GB:
●
6 ports
●
1000BASE-X (GBIC)
●
Cisco IOS Software Release 12.1(8a)EW or later
●
IEEE 802.3
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Enterprise and commercial: designed for high-speed backbone, switch-to-switch applications, or small
server farms
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 13 of 22
●
Service provider: GE small aggregation for DSLAM/PON/mobile data backhaul
Figure 19 shows the WS-X4418-GB.
Figure 19.
WS-X4418-GB Cisco Catalyst 4500 Gigabit Ethernet Module, Server Switching 18 Ports (GBIC)
WS-X4418-GB:
●
18 ports
●
1000BASE-X (GBIC)
●
Cisco IOS Software Release 12.1(8a)EW or later
●
IEEE 802.3, IEEE 802.3x flow control
●
2 ports of wire-speed 1000BASE-X Gigabit Ethernet uplinks
●
16 ports: 4:1 oversubscribed
●
Enterprise and commercial: designed for fiber to the desktop, switch-to-switch applications, or small server
farms
Figure 20 shows the WS-X4448-GB-SFP.
Figure 20.
WS-X4448-GB-SFP Cisco Catalyst 4500 Gigabit Ethernet Module, 48 Ports 1000X (SFP)
WS-X4448-GB-SFP:
●
48 ports
●
1000BASE-X (SFP)
●
Customers can mix and match 1000BASE-X SFP optics on the same line card
●
IEEE 802.3x flow control
●
Service provider: Run point-to-point Gigabit Ethernet fiber to the home (FTTX)
●
Enterprise and commercial: designed for server farms and switch-to-switch applications
Figure 21 shows the WS-X4506-GB-T.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 14 of 22
Figure 21.
WS-X4506-GB-T Cisco Catalyst 4500 6-Port 10/100/1000 RJ-45 PoE IEEE 802.3af and 1000BASE-X (SFP)
WS-X4506-GB-T:
●
6-port 10/100/1000 and 6-port SFP (any combination of up to 6 ports can be active at one time)
●
10/100/1000 RJ-45 PoE and 1000BASE-X (SFP)
●
Cisco IOS Software Release 12.2(20)EWA
●
PoE IEEE 802.3af and Cisco prestandard (RJ-45 only)
●
Provides full line-rate gigabit switching on all ports
●
L2-4 Jumbo Frame support (up to 9216 bytes)
●
Designed to give customers the choice of RJ-45 with or without PoE and SFP without incurring extra costs
●
Enterprise and commercial: high-performance desktop connectivity and server farms; designed to power IP
phones, wireless base stations, video cameras, and other IEEE-compliant appliances
●
Service provider: GE small aggregation for DSLAM/PON/mobile data backhaul
Classic 10/100 Ethernet Line Card
Figure 22 shows the WS-X4248-RJ45V.
Figure 22.
WS-X4248-RJ45V Cisco Catalyst 4500 PoE IEEE 802.3af 10/100, 48 Ports (RJ-45)
WS-X4248-RJ45V:
●
48 ports
●
10/100 (RJ-45)
●
Cisco IOS Software Release 12.2(18)EW or later
●
IEEE 802.3af PoE and Cisco prestandard
●
Enterprise and commercial: designed to power IP phones, wireless base stations, video cameras, and
other IEEE-compliant powered devices
Figure 23 shows the WS-X4148-RJ.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 15 of 22
Figure 23.
WS-X4148-RJ Cisco Catalyst 4500 10/100 Module, 48 Ports (RJ-45)
WS-X4148-RJ:
●
48 ports
●
10/100BASE-T module (RJ-45)
●
Enterprise and commercial: high-port-density solution for desktop connectivity
Classic Fast Ethernet Fiber Line Card
Figure 24 shows the WS-X4248-FE-SFP.
Figure 24.
WS-X4248-FE-SFP Cisco Catalyst 4500 Fast Ethernet Switching Module, 48-Port 100BASE-X (SFP)
WS-X4248-FE-SFP:
●
48-port 100BASE-X (SFP optional)
●
Customers can mix and match 100BASE-X SFP optics on the same line card
●
IEEE 802.3, IEEE 802.3ah, IEEE 802.3x flow control
●
Enterprise and commercial: fiber-to-the-desktop applications
●
Service providers: running point-to-point Fast Ethernet to the home or business (FTTH)
Specification Summary
Table 3 summarizes product specifications.
Table 3.
Line Card
Port Information for Line Cards
Number of
Ports
Port Speed
Port Type
Wire Rate
Cisco Catalyst 4500 Series Min/Max Ports
4503-E
4506-E/
4507R-E/
4507R+E
4510R-E/
4510R+E
E-Series 10 Gigabit Ethernet Line Cards
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 16 of 22
Line Card
Number of
Ports
Port Speed
Port Type
Wire Rate
Cisco Catalyst 4500 Series Min/Max Ports
4503-E
WS-X4712-SFP+E
4
2.5-to-1 with
SFP+
5
12/24
4506-E/
4507R-E/
4507R+E
5
4510R-E/
4510R+E
5
12
10GBASE-R
SFP+ or SFP
12/60
12/96
6
10GBASE-X
X2 or SFP with
TwinGig
Converter
Module
2.5-to-1 with X2
1:1 with SFP
12/24
12/60
12/60
1:1 with SFP
WS-X4606-X2-E
5
5
6/12
5
6/30
5
6/30
5
5
E-Series 10/100/1000 Line Cards
WS-X4748-UPOE+E
48
10/100/1000
RJ-45 UPOE
IEEE 802.3at,
IEEE 802.3af,
Cisco
prestandard
1:1
48/965
48/2405
48/3845,6
WS-X4748-RJ45V+E
48
10/100/1000
RJ-45 PoE
IEEE 802.3at,
IEEE 802.3af,
Cisco
prestandard
1:1
48/965
48/2405
48/3845
WS-X4748-RJ45-E
48
10/100/1000
RJ-45
1:1
48/965
48/2405
48/3845
WS-X4648-RJ45V+E
48
10/100/1000
RJ-45 PoE
IEEE 802.3at,
IEEE 802.3af,
Cisco
prestandard
2-to-1
48/96
WS-X4648-RJ45V-E
48
10/100/1000
RJ-45 PoE
IEEE 802.3af,
Cisco
prestandard
2-to-1
48/96
WS-X4648-RJ45-E
48
10/100/1000
RJ-45
2-to-1
5
48/240
5
48/384 ,
5
48/240
48/96
5
5 6
5
48/384
48/240
5
48/384
5,6
5,6
E-Series Gigabit Ethernet SFP Line Cards
WS-X4624-SFP-E
24
1000
Pluggables
1:1
24/48
24/120
24/168
WS-X4612-SFP-E
12
1000
Pluggables
1:1
12/28
12/64
12/100
WS-X4640-CSFP-E
40 with SFP
1000
Pluggables
2:1 with SFP
40/160
40/400
Not supported
80 with
CSFP
4:1 with CSFP
Classic 10/100/1000 Line Cards
7
WS-X4548RJ45V+
48
10/100/1000
RJ-45 PoE
IEEE 802.3at,
IEEE 802.3af,
Cisco
prestandard
8-to-1
48/96
48/240
48/384
WS-X4548GB-RJ45V
48
10/100/1000
RJ-45 PoE
IEEE 802.3af
and Cisco
prestandard
8-to-1
48/96
48/240
48/384
WS-X4524GB-RJ45V
24
10/100/1000
RJ-45 PoE
IEEE 802.3af
and Cisco
prestandard
4-to-1
24/48
24/120
24/168
WS-X4548-GB-RJ45
48
10/100/1000
RJ-45
8-to-1
48/96
48/240
48/384
4
WS-X4712-SFP+E is not supported on 4507R-E and 4510R-E chassis.
E-Series line cards require E-Series chassis.
6
Requires Supervisor Engine 7-E to support greater than 240 ports on 4510R+E and 4510R-E chassis.
7
The amount of oversubscription can be controlled by varying the number of ports used at 1000 Mbps. All ports can use Gigabit
EtherChannel or IEEE 802.3ad for high-speed interconnection applications. All oversubscribed ports use the standard IEEE
802.1x flow control (PAUSE frame) mechanism to control Gigabit Ethernet host traffic.
5
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 17 of 22
Line Card
Number of
Ports
Port Speed
Port Type
Wire Rate
Cisco Catalyst 4500 Series Min/Max Ports
4503-E
4506-E/
4507R-E/
4507R+E
4510R-E/
4510R+E
Classic Gigabit Ethernet Fiber (GBIC or SFP) Line Cards
WS-X4306-GB
6
1000BASE-X
GBIC
Yes
6/12
6/30
6/42
WS-X4418-GB
18
1000BASE-X
GBIC
2 ports full
18/36
18/90
18/126
16 ports
4-to-1
WS-X4448-GB-LX
48
1000BASE-LX
48 SFPs
(included)
8-to-1
48/96
48/240
48/384
WS-X4448-GB-SFP
48
1000BASE-X
SFP
8-to-1
48/96
48/240
48/384
WS-X4506-GB-T
6+6
10/100/1000
1000BASE-X
(SFP) RJ-45
PoE IEEE
802.3af
and Cisco
prestandard
Yes
6/12
6/30
6/42
100BASE-X
SFP
Yes
48/96
48/240
48/384
Classic Fast Ethernet Fiber Line Cards
WS-X4248-FE-SFP
48
Classic 10/100 Ethernet Line Cards
WS-X4148-RJ
48
10/100
RJ-45
Yes
48/96
48/240
48/384
WS-X4248-RJ45V
48
10/100
RJ-45 PoE
IEEE 802.3af
and Cisco
prestandard
Yes
48/96
48/240
48/384
Optics
Cisco Catalyst 4500 line cards provide a variety of optical port types and port speeds: SFP+, X2, SFP, GBIC,
100BASE-FX, and so on. For details about the different optical modules supported by each line card and the
minimum Cisco IOS Software release required for each of the supported optical modules, visit
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html.
Product Specification
Table 4 lists product specifications.
Table 4.
Product Specifications
Feature
Description
Standards
● Gigabit Ethernet: IEEE 802.3z, IEEE 802.3x, IEEE 802.3ab, IEEE 803.3at, IEEE 802.3af, IEEE 802.3az
● 1000BASE-X (GBIC), 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-ZX, CWDM
EtherChannel
Technology
● Gigabit EtherChannel: All 1000 Mbps ports
● 10 Gigabit EtherChannel: All 10Gbps ports
● IEEE 802.3ad (Link Aggregation Control Protocol): All 1000 Mbps ports
● Port Aggregation Protocol (PagP): Yes
● Number of ports per tuple: 8
● EtherChannel and IEEE 802.3ad technology across line cards: Yes
Physical Dimensions
● Occupies one slot in the Cisco Catalyst 4500 Series platform
● Dimensions (H x W x D): 1.2 x 14.25 x 10.75 in. (3.0 x 36.2 x 27.3 cm)
Environmental
Conditions
● Operating temperature: 32° to 104°F (0° to 40°C)
● Storage temperature: -40° to 167°F (-40° to 75°C)
● Relative humidity: 10 to 90%, noncondensing
● Operating altitude: -60 to 3000m
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 18 of 22
Feature
Description
Safety Conditions
Fiber optic lasers: Class 1 laser products
Safety Certifications
● UL 1950
● EN 60950
● CSA-C22.2 no 950
● IEC 950
Electromagnetic
Emissions Certifications
● FCC 15J Class A
● VCCI Class A
● CE Marking
● EN 55022 Class A
● EN 55024 Class A
● CISPR 22 Class A
● AS/NZ 3548
● NEBS Level 3 (GR-1089-CORE, GR-63-CORE)
● ETSI ETS-300386-2
● EN 50121-4
ROHS Compliance
ROHS5
Power and MTBF Information
Table 5 gives power and MTBF information for different line cards.
Table 5.
Power and MTBF Information
Part Number
Max Rated Power (W)
Rated MTBF (Hours)
WS-X4748-UPOE+E
75
140,696
WS-X4748-RJ45V+E
75
183,330
WS-X4748-RJ45-E
75
402,386
WS-X4712-SFP+E
90
387,172
WS-X4624-SFP-E
45
591,109
WS-X4612-SFP-E
30
676,740
WS-X4640-CSFP-E
120
347,724
WS-X4648-RJ45-E
89
280,365
WS-X4648-RJ45V-E
92
280,365
WS-X4648-RJ45V+E
92
280,365
WS-X4606-X2-E
50
535,717
WS-X4548-GB-RJ45V
60
434,646
WS-X4548-RJ45V+
60
239,436
WS-X4548-GB-RJ45
60
171,356
WS-X4506-GB-T
30
392,098
WS-X4306-GB
35
570,262
WS-X4418-GB
80
355,330
WS-X4448-GB-SFP
65
290,732
WS-X4248-FE-SFP
53
687,828
WS-X4148-RJ
65
350,860
WS-X4248-RJ45V
60
187,594
Note:
All power numbers shown in Table 5 are maximum values recommended for facility power and cooling
capacity planning. These figures are not indicative of the actual power draw during operation. Typical power draw
is about 20 percent lower than the maximum value shown.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 19 of 22
Ordering Information
To place an order, visit the Cisco Ordering homepage. Table 6 gives ordering information.
Table 6.
Ordering Information
Part Number (“=” Indicates
“Spare”)
Product Name
WS-X4748-UPOE+E (=)
Cisco Catalyst 4500E Series 48-Port UPOE 10/100/1000 (RJ-45)
WS-UPOE-12VPSPL(=)
Cisco Catalyst 4500E Series UPOE Power Splitter
WS-X4748-RJ45V+E (=)
Cisco Catalyst 4500E Series 48-Port 802.3at PoEP 10/100/1000 (RJ-45)
WS-X4748-RJ45-E (=)
Cisco Catalyst 4500E Series 48-Port 10/100/1000 (RJ-45)
WS-X4712-SFP+E (=)
Cisco Catalyst 4500E Series 12-Port 10 Gigabit Ethernet (SFP+)
WS-X4624-SFP-E (=)
Cisco Catalyst 4500E Series 24-Port GE (SFP)
WS-X4612-SFP-E (=)
Cisco Catalyst 4500E Series 12-Port GE (SFP)
WS-X4640-CSFP-E (=)
Cisco Catalyst 4500E Series 40 SFP/80 C-SFP Port 1000BaseX (SFPs Optional)
WS-X4648-RJ45-E (=)
Cisco Catalyst 4500E Series 48-Port 10/100/1000 (RJ-45)
WS-X4648-RJ45V-E (=)
Cisco Catalyst 4500E Series 48-Port 802.3af PoE 10/100/1000 (RJ-45)
WS-X4648-RJ45V+E (=)
Cisco Catalyst 4500E Series 48-Port 802.3af PoE and PoEP - 10/100/1000 (RJ-45)
WS-X4606-X2-E (=)
Cisco Catalyst 4500E Series 6-Port 10 Gigabit Ethernet (X2)
WS-X4548-GB-RJ45V(=)
Cisco Catalyst 4500 PoE IEEE 802.3af 10/100/1000, 48 Ports (RJ-45)
WS-X4548-RJ45V+(=)
Cisco Catalyst 4500 PoE IEEE 802.3af and PoEP-Ready 10/100/1000, 48 Ports (RJ-45)
WS-X4548-GB-RJ45(=)
Cisco Catalyst 4500 Enhanced 48-Port 10/100/1000 Module (RJ-45)
WS-X4506-GB-T(=)
Cisco Catalyst 4500 6-Port 10/100/1000 RJ-45 PoE IEEE 802.3af and 1000BASE-X (SFP)
WS-X4306-GB(=)
Cisco Catalyst 4500 Gigabit Ethernet Module, 6 Ports (GBIC)
WS-X4418-GB(=)
Cisco Catalyst 4500 Gigabit Ethernet Module, Server Switching 18 Ports (GBIC)
WS-X4448-GB-SFP(=)
Cisco Catalyst 4500 Gigabit Ethernet Module, 48-Port 1000X (SFP)
WS-X4248-FE-SFP (=)
Cisco Catalyst 4500 Fast Ethernet Switching Module, 48-Port 100BASE-X (SFP)
WS-X4148-RJ(=)
Cisco Catalyst 4500 10/100 Module, 48 Ports (RJ-45)
WS-X4248-RJ45V(=)
Cisco Catalyst 4500 PoE IEEE 802.3af 10/100, 48 Ports (RJ-45)
Cisco Limited Lifetime Hardware Warranty
The Cisco limited lifetime hardware warranty (LLW) includes 10-day advance hardware replacement for as long as
the original end user owns the product. Table 7 describes the limited lifetime hardware warranty.
Your formal warranty statement, including the warranty applicable to Cisco software, appears in the Cisco
information packet that accompanies your Cisco product. We encourage you to review carefully the warranty
statement shipped with your specific product before use.
For additional information on warranty terms, visit http://www.cisco.com/go/warranty.
Adding a Cisco technical services contract to your device coverage provides benefits not available with warranty,
including access to the Cisco Technical Assistance Center (TAC), a variety of hardware replacement options to
meet critical business needs, updates for licensed IOS software, and registered access to the extensive
Cisco.com knowledge base and support tools. Table 8 describes the benefits and features of Cisco technical
services.
For information about Cisco Technical Services, go to http://www.cisco.com/go/ts.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 20 of 22
Table 7.
Limited Lifetime Hardware Warranty
8
Cisco Limited Lifetime Hardware Warranty
Warranty Duration
As long as the original end user continues to own or use the product, except for the fan and power supply, which
are limited to 5 years.
EoL Policy
In the event of discontinuance of product manufacture, Cisco warranty support is limited to 5 years from the
announcement of discontinuance.
Hardware Replacement
Cisco or its service center will use commercially reasonable efforts to ship a replacement part within 10 business
days after receipt of the RMA request and confirmation that a replacement part is appropriate response. Actual
delivery times may vary depending on customer location.
Effective Date
Hardware warranty commences from the date of shipment to the customer (and in case of resale by a Cisco
reseller, not more than 90 days after original shipment by Cisco).
TAC Support
None.
Cisco.com Access
Warranty allows guest access only to Cisco.com.
8
Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.
Cisco and Partner Services
Enable the innovative, secure, intelligent edge in the Borderless Network Architecture using personalized services
from Cisco and our partners. Through a discovery process that begins with understanding your business
objectives, we help you integrate the next-generation Cisco Catalyst 4500-E Series Switches into your architecture
and incorporate network services onto that platform. Sharing knowledge and leading practices, we support your
success every step of the way as you deploy, absorb, manage, and scale new technology. Choose from a flexible
suite of support services designed to meet your business needs and help you maintain high-quality network
performance while controlling operational costs. Table 8 shows the Cisco technical services available for Cisco
Catalyst 4500-E Series Switches.
For additional information about Cisco services, visit http://www.cisco.com/go/ts.
Table 8.
Cisco Technical Services for Cisco Catalyst 4500-E Series Switches
Technical Services
Cisco SMARTnet Service
● Around-the-clock, global access to the Cisco Technical Assistance Center (TAC)
● Unrestricted access to the extensive Cisco.com resources, communities, and tools
● Next-business-day, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement9 and onsite parts replacement and installation available
● Ongoing operating system software updates within the licensed feature set10
● Proactive diagnostics and real-time alerts on Smart Call Home enabled devices
Cisco Smart Foundation Service
● Next business day advance hardware replacement as available
● Business hours access to SMB TAC (access levels vary by region)
● Access to Cisco.com SMB knowledge base
● Online technical resources through Smart Foundation Portal
● Operating system software bug fixes and patches
Cisco Focused Technical Support Services
Three levels of premium, high-touch services are available:
● Cisco High-Touch Operations Management Service
● Cisco High-Touch Technical Support Service
● Cisco High-Touch Engineering Service
Valid Cisco SMARTnet or SP Base contracts on all network equipment are required.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 21 of 22
Footnotes:
9
Advance hardware replacement is available in various service-level combinations. For example, 8x5xNBD indicates that
shipment will be initiated during the standard eight-hour business day, five days a week (the generally accepted business days
within the relevant region), with next business day (NBD) delivery. Where NBD is not available, same-day shipping is provided.
Restrictions apply; please review the appropriate service descriptions for details.
10
Cisco operating system updates include the following: maintenance releases, minor updates, and major updates within the
licensed feature set.
For More Information
For more information about the Cisco Catalyst 4500 Series line cards, visit
http://www.cisco.com/en/US/products/hw/switches/ps4324/index.html or contact your local account representative.
For more information about Cisco transceiver modules compatible with Cisco Catalyst 4500 Series line cards, visit
http://www.cisco.com/en/US/products/hw/modules/ps5455/products_device_support_tables_list.html.
Printed in USA
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-364099-17
01/12
Page 22 of 22
ITEM 5
Data Sheet
Cisco Catalyst 2960-S and 2960 Series Switches with LAN Base
Software
®
®
The Cisco Catalyst 2960-S and 2960 Series Switches are the leading Layer 2 edge, providing improved
ease of use, highly secure business operations, improved sustainability, and a borderless network
experience. The Cisco Catalyst 2960-S Series Switches include new Cisco FlexStack switch stacking
capability with 1 and 10 Gigabit connectivity, and Power over Ethernet Plus (PoE+) with the Cisco Catalyst
2960 Switches offering fast Ethernet access connectivity and PoE capabilities. The Cisco Catalyst 2960-S
and 2960 Series are fixed-configuration access switches designed for enterprise, midmarket, and branch
office networks to provide lower total cost of ownership. The Cisco Catalyst 2960-S is shown in Figure 1,
and the Cisco Catalyst 2960 Series Switches are shown in Figure 2.
What’s new for the Cisco Catalyst 2960-S Series Switches with LAN Base software:
●
10 and 1 Gigabit Ethernet uplink flexibility with Small Form-Factor Pluggable Plus (SFP+), providing business
continuity and fast transition to 10 Gigabit Ethernet
●
24 or 48 ports of Gigabit Ethernet desktop connectivity
●
Cisco FlexStack stacking module with 40 Gbps of throughput, allowing ease of operation with single
configuration and simplified switch upgrade
●
PoE+ with up to 30W per port that allows you to support the latest PoE+ capable devices
●
Power supply options, with 740W or 370W fixed power supplies for PoE+ switches are available
●
USB storage for file backup, distribution, and simplified operations
●
A wide range of software features to provide ease of operation, highly secure business operations,
sustainability, and a borderless network experience
●
Limited lifetime hardware warranty, including next-business-day replacement with 90-day service and support
The Cisco Catalyst 2960 Series Switches with LAN Base software offer the following:
●
Dual-purpose uplinks for Gigabit Ethernet uplink flexibility, allowing use of either a copper or fiber uplink; each
dual-purpose uplink port has one 10/100/1000 Ethernet port and one SFP-based Gigabit Ethernet port, with
one port active at a time
●
24 or 48 ports of Fast Ethernet desktop connectivity
●
PoE configurations with up to 15.4W per port
●
A wide range of software features to provide ease of operation, highly secure business operations,
sustainability, and a borderless networking experience
●
Limited lifetime hardware warranty
Figure 1.
Cisco Catalyst 2960-S Series Switches
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 26
Data Sheet
Figure 2.
Cisco Catalyst 2960 Series Switches
Switch Configurations
Table 1 shows the configuration information for the Cisco Catalyst 2960-S Series Switches with LAN Base software,
and Table 2 shows the configuration information for the Cisco Catalyst 2960 Series Switches with LAN Base
software.
Table 1.
Configurations of Cisco Catalyst 2960-S Series Switches with LAN Base Software
Cisco Catalyst 2960-S Switch Model
Description
Uplinks
Available PoE Power
10 Gigabit Uplinks with 10/100/1000 Ethernet Connectivity
Cisco Catalyst 2960S-48FPD-L
48 Ethernet 10/100/1000 PoE+ ports
2 Ten Gigabit Ethernet SFP+ or 2 One
Gigabit Ethernet SFP ports
740W
Cisco Catalyst 2960S-48LPD-L
48 Ethernet 10/100/1000 PoE+ ports
2 Ten Gigabit Ethernet SFP+ or 2 One
Gigabit Ethernet SFP ports
370W
Cisco Catalyst 2960S-24PD-L
24 Ethernet 10/100/1000 PoE+ ports
2 Ten Gigabit Ethernet SFP+ or 2 One
Gigabit Ethernet SFP ports
370W
Cisco Catalyst 2960S-48TD-L
48 Ethernet 10/100/1000 ports
2 Ten Gigabit Ethernet SFP+ or 2 One
Gigabit Ethernet SFP ports
-
Cisco Catalyst 2960S-24TD-L
24 Ethernet 10/100/1000 ports
2 Ten Gigabit Ethernet SFP+ or 2 One
Gigabit Ethernet SFP ports
-
1 Gigabit Uplinks with 10/100/1000 Ethernet Connectivity
Cisco Catalyst 2960S-48FPS-L
48 Ethernet 10/100/1000 PoE+ ports
4 One Gigabit Ethernet SFP ports
740W
Cisco Catalyst 2960S-48LPS-L
48 Ethernet 10/100/1000 PoE+ ports
4 One Gigabit Ethernet SFP ports
370W
Cisco Catalyst 2960S-24PS-L
24 Ethernet 10/100/1000 PoE+ ports
4 One Gigabit Ethernet SFP ports
370W
Cisco Catalyst 2960S-48TS-L
48 Ethernet 10/100/1000 ports
4 One Gigabit Ethernet SFP ports
-
Cisco Catalyst 2960S-24TS-L
24 Ethernet 10/100/1000 ports
4 One Gigabit Ethernet SFP ports
-
All models available with optional Cisco FlexStack stacking module.
Cisco Catalyst 2960S-STACK is optional Stacking Module for all 2960-S LAN Base switches that includes a.5M stack cable.
No DC Power supplies are available.
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 26
Data Sheet
Table 2.
Configurations of Cisco Catalyst 2960 Series Switches with LAN Base Software
Cisco Catalyst 2960 Switch Model
Description
Uplinks
Available PoE Power
1 Gigabit Uplinks with 10/100 Ethernet Connectivity
Cisco Catalyst 2960-48PST-L
48 Ethernet 10/100 PoE ports
2 one Gigabit Ethernet SFP ports and 2
fixed Ethernet 10/100/1000 ports
370W
Cisco Catalyst 2960-24PC-L
24 Ethernet 10/100 PoE ports
2 dual-purpose ports (10/100/1000 or SFP)
370W
Cisco Catalyst 2960-24LT-L
24 Ethernet 10/100 ports
2 Ethernet 10/100/1000 ports
123W
Cisco Catalyst 2960-24TC-L
24 Ethernet 10/100 ports
2 dual-purpose ports
-
Cisco Catalyst 2960-48TC-L
48 Ethernet 10/100 ports
2 dual-purpose ports (10/100/1000 or SFP)
-
Cisco Catalyst 2960-24TT-L
24 Ethernet 10/100 ports
2 Ethernet 10/100/1000 ports
-
Cisco Catalyst 2960-48TT-L
48 Ethernet 10/100 ports
2 Ethernet 10/100/1000 ports
-
1 Gigabit Uplinks with 10/100/1000 Ethernet Connectivity
Cisco Catalyst 2960G-24TC-L
20 Ethernet 10/100/1000 ports
4 dual-purpose ports (10/100/1000 or SFP)
Cisco Catalyst 2960G-48-TC-L
44 Ethernet 10/100/1000 ports
4 dual-purpose ports (10/100/1000 or SFP)
Compact Switches
Cisco Catalyst 2960-8TC-L
8 Ethernet 10/100 ports; compact size 1 dual-purpose port (10/100/1000 or SFP)
with no fan
Cisco Catalyst 2960PD-8TT-L
8 Ethernet 10/100 ports; compact size 1 10/100/1000 PoE input port
with no fan
Cisco Catalyst 2960G-8TC-L
7 Ethernet 10/100/1000 ports;
compact size with no fan
1 dual-purpose port (10/100/1000 or SFP)
Cisco FlexStack Stacking
®
Cisco FlexStack stacking with a hot-swappable module and Cisco IOS Software provides true stacking, all switches
in a stack act as a single switch unit. The Cisco FlexStack provides a unified data plane, unified configuration, and
single IP address management for a group of switches. The advantages of true stacking are lower total cost of
ownership through simplified management and higher availability. Cisco FlexStack supports cross-stack features
including EtherChannel, SPAN and FlexLink technology. A stack module can be added to any Cisco Catalyst 2960-S
switch with LAN Base software to quickly upgrade the switch to make it stack capable, and the switch added to the
®
stack will upgrade to the correct Cisco IOS Software version and transparently become a stack member. Figure 3
shows the FlexStack stacking module for the Cisco Catalyst 2960-S.
Figure 3.
Cisco Catalyst 2960-S Switches with Cisco FlexStack Modules and Stack Cabling
Power over Ethernet Plus
In addition to PoE 802.3af, the Cisco Catalyst 2960-S Series Switches support Power over Ethernet Plus (PoE+)
(IEEE 802.3at standard), which provides up to 30W of power per port. The Cisco Catalyst 2960-S and 2960 Series
Switches can provide a lower total cost of ownership for deployments that incorporate Cisco IP phones, Cisco
®
Aironet wireless LAN (WLAN) access points, or any IEEE 802.3af-compliant end device. PoE removes the need for
wall power to each PoE-enabled device and eliminates the cost for additional electrical cabling and circuits that
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 26
Data Sheet
would otherwise be necessary in IP phone and WLAN deployments. Table 3 shows the power supply combinations
required for different PoE needs.
Table 3.
Switch PoE and PoE+ Power Capacity
Switch Model
Maximum Number of PoE+
*
(IEEE 802.3at) Ports
Maximum Number of PoE
*
(IEEE 802.3af) Ports
Available PoE Power
10 Gigabit Uplinks with 10/100/1000 Ethernet Connectivity
Cisco Catalyst 2960S-48FPD-L
24 ports up to 30W
48 ports up to 15.4W
740W
Cisco Catalyst 2960S-48LPD-L
12 ports up to 30W
24 ports up to 15.4W
370W
48 ports up to 7.7W
Cisco Catalyst 2960S-24PD-L
12 ports up to 30W
24 ports up to 15.4W
370W
1 Gigabit Uplinks with 10/100/1000 Ethernet Connectivity
Cisco Catalyst 2960S-48FPS-L
24 ports up to 30W
48 ports up to 15.4W
740W
Cisco Catalyst 2960S-48LPS-L
12 ports up to 30W
24 ports up to 15.4W
370W
48 ports up to 7.7W
Cisco Catalyst 2960S-24PS-L
12 ports up to 30W
24 ports up to 15.4W
370W
Cisco Catalyst 2960-48PST-L
N/A
24 ports up to 15.4W
370W
48 ports up to 7.7W
Cisco Catalyst 2960-24PC-L
N/A
24 ports up to 15.4W
370W
Cisco Catalyst 2960-24LT-L
N/A
8 ports up to 15.4W
123W
*
Intelligent power management allows flexible power allocation across all ports.
Cisco Catalyst 2960-S and 2960 Series Switches Enable Cisco Borderless Network
Borderless Networks, a Cisco architecture, deliver the new workspace experience, connecting anyone, anywhere,
using any device, to any resource securely, reliably, and transparently. Cisco’s Borderless Networks architecture
addresses primary IT and business challenges to help create a truly borderless experience by bringing interactions
closer to the employee and customer.
Borderless experience is only possible with intelligent network elements designed and architected to meet the needs
of a global workspace. Cisco Network Access is a primary component of this architecture, enabling various
borderless network services such as mobility, security, sustainability, and ease of operations for increased
productivity and operational efficiency. When network access is intelligent, it knows the identity of the user, as well
as where the user is on the network. It knows what is connecting to the network, to automatically provision the
network for QoS and delivery. It becomes services-aware to optimize user experience. Only with intelligent access
network, your enterprise can go borderless securely and transparently. Your business can save energy, simplify
operations with better business efficiency, and have an optimized total cost of ownership.
Cisco Network Access for Borderless solution focuses on the following primary areas:
●
Sustainability
●
Ease of operations
●
Borderless security
●
Borderless experience
Sustainability
Cisco Catalyst switching solutions enable greener practices through measurable power efficiency, integrated
services, and continuous innovations such as Cisco EnergyWise, an enterprisewide solution that monitors and
conserves energy with customized policies. Together, Cisco EnergyWise technology and Cisco Catalyst switches
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 26
Data Sheet
reduce greenhouse gas (GhG) emissions and increase energy cost savings and sustainable business behavior.
Sustainability features in the Cisco Catalyst 2960-S and 2960 Series Switches include the following features sets:
●
Cisco EnergyWise technology
●
Efficient switch operation
●
Intelligent power management
Cisco EnergyWise Technology
Cisco EnergyWise is an innovative architecture, added to fixed configuration switches, promoting companywide
sustainability by reducing energy consumption across an entire corporate infrastructure and affecting more than 50
percent of global greenhouse gas emissions created by worldwide building infrastructure, a much greater effect than
the 2 percent generated by the IT industry. Cisco EnergyWise enables companies to measure the power
consumption of network infrastructure and network-attached devices and manage power consumption with specific
policies, reducing power consumption to realize increased cost savings, potentially affecting any powered device.
EnergyWise encompasses a highly intelligent network-based approach to communicate messages that measure
and control energy between network devices and endpoints. The network discovers Cisco EnergyWise-manageable
devices, monitors their power consumption, and takes action based on business rules to reduce power consumption.
EnergyWise uses a unique domain-naming system to query and summarize information from large sets of devices,
making it simpler than traditional network management capabilities. Cisco EnergyWise’s management interfaces
allow facilities and network management applications to communicate with endpoints and each other using the
network as a unifying fabric. The management interface uses standard SNMP or TCP to integrate Cisco and thirdparty management systems.
Efficient Switch Operation
Cisco Catalyst 2960-S and 2960 Series Switches, designed and engineered by Cisco, provide optimum power
saving, low power operations for industry best-in-class power management, and power consumption capabilities.
The Cisco Catalyst 2960-S ports are capable of reduced power modes so that ports not in use can move into a lower
power utilization state.
Intelligent Power Over Ethernet Management
The Cisco Catalyst 2960-S PoE models support the latest PoE+ devices including Cisco IP phones and Cisco
Aironet WLAN access points providing up to 30W of power per port, as well as any IEEE 802.3af-compliant end
device.
●
Per Port Power Consumption command allows customers to specify maximum power setting on an
individual port.
●
Per Port PoE Power Sensing measures actual power being drawn, enabling more intelligent control of
powered devices.
●
Cisco Discovery Protocol Version 2 allows switches to negotiate a more granular power setting when
connecting to a Cisco powered device such as IP phones or access points than what is provided by
IEEE classification.
●
The PoE MIB provides proactive visibility into power usage and allows customers to set different
power-level thresholds.
Ease of Operations
The Cisco Catalyst 2960-S and 2960 Series Switches help reduce the operating costs through:
●
Cisco Catalyst Smart Operations
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 26
Data Sheet
●
Easy to use deployment and control features
●
Advanced, intelligent network management tools
Cisco Catalyst Smart Operations
Cisco Catalyst Smart Operations is a comprehensive set of capabilities that simplify LAN deployment, configuration,
and troubleshooting. Cisco Catalyst Smart Operations enable zero touch installation and replacement of switches,
fast upgrade, as well as ease of troubleshooting with reduced operational cost.
Cisco Catalyst Smart Operations is a set of features that includes Smart Install, Auto Smartports, Smart
Configuration, and Smart Troubleshooting to enhance operational excellence:
●
Cisco Smart Install is a transparent plug-and-play technology to configure the Cisco IOS Software image
and switch configuration without user intervention. Smart Install utilizes dynamic IP address allocation and the
assistance of other switches to facilitate installation providing transparent network plug and play.
●
Cisco Auto Smartports provide automatic configuration as devices connect to the switch port, allowing auto
detection and plug and play of the device onto the network.
●
Cisco Smart Configuration provides a single point of management for a group of switches and in addition
adds the ability archive and backup configuration files to a file server or switch allowing seamless zero touch
switch replacement.
●
Cisco Smart Troubleshooting is an extensive array of debug diagnostic commands and system health
checks within the switch, including Generic Online Diagnostics (GOLD) and Onboard Failure Logging (OBFL).
Easy-to-Use Deployment and Control Features
●
Automatic QoS (AutoQoS) simplifies QoS configuration in voice over IP (VoIP) networks by issuing interface
and global switch commands to detect Cisco IP phones, classify traffic, and help enable egress queue
configuration.
●
Stacking Master Configuration Management and Cisco FlexStack stacking helps ensure that all switches
are automatically upgraded when the master switch receives a new software version. Automatic software
version checking and updating help ensure that all stack members have the same software version.
●
Dynamic Host Configuration Protocol (DHCP) autoconfiguration of multiple switches through a boot server
eases switch deployment.
●
Auto-Negotiation on all ports automatically selects half- or full-duplex transmission mode to
optimize bandwidth.
●
Dynamic Trunking Protocol (DTP) facilitates dynamic trunk configuration across all switch ports.
●
Port Aggregation Protocol (PAgP) automates the creation of Cisco Fast EtherChannel groups or Gigabit
®
EtherChannel groups to link to another switch, router, or server.
●
Link Aggregation Control Protocol (LACP) allows the creation of Ethernet channeling with devices that
conform to IEEE 802.3ad. This feature is similar to Cisco EtherChannel technology and PAgP.
●
Automatic Media-Dependent Interface Crossover (MDIX) automatically adjusts transmit and receive pairs
if an incorrect cable type (crossover or straight-through) is installed.
●
Unidirectional Link Detection Protocol (UDLD) and Aggressive UDLD allow unidirectional links caused by
incorrect fiber-optic wiring or port faults to be detected and disabled on fiber-optic interfaces.
●
Switching Database Manager (SDM) templates for access, routing, and VLAN deployment allow the
administrator to easily maximize memory allocation to the desired features based on deployment-specific
requirements.
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 26
Data Sheet
●
Local Proxy Address Resolution Protocol (ARP) works in conjunction with Private VLAN Edge to minimize
broadcasts and maximize available bandwidth.
●
Internet Group Management Protocol (IGMP) Snooping for IPv4 and IPv6 MLD v1 and v2 Snooping
provide fast client joins and leaves of multicast streams and limit bandwidth-intensive video traffic to only the
requestors.
●
Multicast VLAN Registration (MVR) continuously sends multicast streams in a multicast VLAN while
isolating the streams from subscriber VLANs for bandwidth and security reasons.
●
Per-port Broadcast, Multicast, and Unicast Storm Control prevents faulty end stations from degrading
overall systems performance.
●
Voice VLAN simplifies telephony installations by keeping voice traffic on a separate VLAN for easier
administration and troubleshooting.
●
Cisco VLAN Trunking Protocol (VTP) supports dynamic VLANs and dynamic trunk configuration across all
switches.
●
Remote Switch Port Analyzer (RSPAN) allows administrators to remotely monitor ports in a Layer 2 switch
network from any other switch in the same network.
●
For enhanced traffic management, monitoring, and analysis, the Embedded Remote Monitoring (RMON)
software agent supports four RMON groups (history, statistics, alarms, and events).
●
Layer 2 Traceroute eases troubleshooting by identifying the physical path that a packet takes from source to
destination.
●
Trivial File Transfer Protocol (TFTP) reduces the cost of administering software upgrades by downloading
from a centralized location.
●
Network Timing Protocol (NTP) provides an accurate and consistent timestamp to all intranet switches.
Advanced, Intelligent Network Management Tools
The Cisco Catalyst 2960-S and 2960 Series Switches offer both a superior CLI for detailed configuration and Cisco
Network Assistant software, a PC-based tool for quick configuration based on preset templates. In addition,
CiscoWorks LAN Management Solution (LMS) supports the Cisco Catalyst 2960-S and 2960 Series Switches for
networkwide management.
CiscoWorks LAN Management Solution
CiscoWorks LAN Management Solution (LMS) is a comprehensive network lifecycle management solution. It
provides an extensive library of easy-to-use features to automate the initial and day-to-day management of your
Cisco network infrastructure. CiscoWorks LMS uniquely uses Cisco hardware and software platform knowledge and
operational experience into a powerful set of workflow-driven configuration, monitoring, troubleshooting, reporting,
and administrative tools. Including:
●
Support for new Cisco hardware platforms the day they ship
●
Support for new technologies and services from initial deployment to day-to-day administration and
management, such as EnergyWise, Identity, Cisco Auto Smartports, Cisco Smart Install, and much more
●
Configuration management tools built from Cisco experience and Cisco Validated Design recommendations
●
Monitoring and troubleshooting capabilities that incorporates Cisco hardware best practices and
diagnostics features
●
Automation in managing hardware inventories, security vulnerabilities (PSIRTS), and platform end-of-life and
support cycles
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 26
Data Sheet
For detailed information about CiscoWorks LMS, go to
http://www.cisco.com/en/US/products/sw/cscowork/ps2425/index.html.
Borderless Security
The Cisco Catalyst 2960-S and 2960 Series Switches provide superior Layer 2 threat defense capabilities for
mitigating man-in-the-middle attacks (such as MAC, IP, and ARP spoofing). TrustSec, a primary element of
Borderless Security Architecture, helps enterprise customers secure their networks, data and resources with
policybased access control, identity and role-aware networking, pervasive integrity, and confidentiality. The
borderless security is enabled by the following feature sets in the Cisco Catalyst 2960-S and 2960 SeriesSwitches:
●
Threat defense
●
Cisco TrustSec
●
Other advanced security features
Threat Defense
Cisco Integrated Security Features is an industry-leading solution available on Cisco Catalyst Switches that
proactively protects your critical network infrastructure. Delivering powerful, easy-to-use tools to effectively prevent
the most common and potentially damaging Layer 2 security threats, Cisco Integrated Security Features provides
robust security throughout the network. Cisco Integrated Security Features include Port Security, DHCP Snooping,
Dynamic ARP Inspection, and IP Source guard.
●
Port Security secures the access to an access or trunk port based on MAC address. It limits the number of
learned MAC addresses to deny MAC address flooding.
●
DHCP Snooping prevents malicious users from spoofing a DHCP server and sending out bogus addresses.
This feature is used by other primary security features to prevent a number of other attacks such as ARP
poisoning.
●
Dynamic ARP Inspection (DAI) helps ensure user integrity by preventing malicious users from exploiting the
insecure nature of the ARP protocol.
●
IP Source Guard prevents a malicious user from spoofing or taking over another user’s IP address by
creating a binding table between the client’s IP and MAC address, port, and VLAN.
Cisco TrustSec
TrustSec secures access to the network, enforces security policies, and delivers standard based security solutions
such as 802.1X enabling secure collaboration and policy compliance. TrustSec capabilities reflect Cisco thought
leadership, innovations, and commitment to customer success. These new capabilities include:
●
Flexible Authentication that supports multiple authentication mechanisms including 802.1X, MAC
Authentication Bypass and web authentication using a single, consistent configuration
●
Open Mode that creates a user friendly environment for 802.1X operations
●
Integration of Device Profiling Technology and Guest Access handling with Cisco switching to
significantly improve security while reducing deployment and operational challenges
●
RADIUS Change of Authorization and Downloadable Calls for comprehensive policy management
capabilities
●
802.1X Supplicant with Network Edge Access Transport (NEAT) enables extended secure access where
compact switches in the conference rooms have the same level of security as switches inside the locked
wiring closet
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 8 of 26
Data Sheet
Other Advanced Security Features
Other Advanced Security features include but are not limited to:
●
Private VLAN Edge provides security and isolation between switch ports, which helps ensure that users
cannot snoop on other users’ traffic.
●
Multidomain Authentication allows an IP phone and a PC to authenticate on the same switch port while
placing them on appropriate voice and data VLAN.
●
Port-Based ACLs for Layer 2 interfaces allow security policies to be applied on individual switch ports.
●
Secure Shell (SSH) Protocol, Kerberos, and Simple Network Management Protocol Version 3
(SNMPv3) provide network security by encrypting administrator traffic during Telnet and SNMP sessions.
SSH Protocol, Kerberos, and the cryptographic version of SNMPv3 require a special cryptographic software
image because of U.S. export restrictions.
●
Bidirectional data support on the Switched Port Analyzer (SPAN) port allows Cisco Intrusion Detection
System (IDS) to take action when an intruder is detected.
●
TACACS+ and RADIUS Authentication facilitates centralized control of the switch and restricts
unauthorized users from altering the configuration.
●
MAC Address Notification allows administrators to be notified of users added to or removed from the
network.
●
Multilevel Security on Console Access prevents unauthorized users from altering the switch configuration.
●
Bridge Protocol Data Unit (BPDU) Guard shuts down Spanning Tree PortFast-enabled interfaces when
BPDUs are received to avoid accidental topology loops.
●
Spanning Tree Root Guard (STRG) prevents edge devices not in the network administrator’s control from
becoming Spanning Tree Protocol root nodes.
●
IGMP Filtering provides multicast authentication by filtering out nonsubscribers and limits the number of
concurrent multicast streams available per port.
●
Dynamic VLAN Assignment is supported through implementation of VLAN Membership Policy Server client
capability to provide flexibility in assigning ports to VLANs. Dynamic VLAN facilitates the fast assignment of
IP addresses.
Borderless Experience
Borderless network enables enterprise mobility and business-grade video services. The industry’s first unified
network (wired and wireless) location services enable tracking of mobile assets and the users of those assets for
both wired and wireless devices. The true borderless experience is enabled by the following feature sets in the Cisco
Catalyst 2960-S and 2960 Series Switches:
●
High availability and Layer 2 networking
●
Enhanced quality of service (QoS)
●
Location awareness and mobility
High Availability and Layer 2 Networking
The Cisco Catalyst 2960-S Series Switches provides Cisco FlexStack stacking and both the Cisco Catalyst 2960-S
and 2960 Series switches provide Layer 2 networking to enable resiliency and availability.
Other high-availability features include but are not limited to:
●
Cross-Stack EtherChannel provides the ability to configure Cisco EtherChannel technology across different
members of the Cisco FlexStack for high resiliency.
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 9 of 26
Data Sheet
●
Flexlink provides link redundancy with convergence time less than 100 ms.
●
IEEE 802.1s/w Rapid Spanning Tree Protocol (RSTP) and Multiple Spanning Tree Protocol (MSTP)
provide rapid spanning-tree convergence independent of spanning-tree timers and also offer the benefit of
Layer 2 load balancing and distributed processing. Stacked units behave as a single spanning-tree node.
●
Per-VLAN Rapid Spanning Tree (PVRST+) allows rapid spanning-tree reconvergence on a per-VLAN
spanning-tree basis, without requiring the implementation of spanning-tree instances.
●
Switch-port Autorecovery (Errdisable) automatically attempts to reactivate a link that is disabled because
of a network error.
Enhanced Quality of Service
The Cisco Catalyst 2960-S and 2960 Series Switches offers intelligent services that keep everything flowing
smoothly. Industry-leading mechanisms for marking, classification, and scheduling deliver superior performance for
data, voice, and video traffic, all at wire speed.
Following are some of the QoS features supported in the Cisco Catalyst 2960-S and 2960 Series Switches:
●
Cross-Stack QoS allows QoS to be configured across the entire Cisco Catalyst 2960-S Flexstack.
●
802.1p Class of Service (CoS) and differentiated services code point (DSCP) field classification are
provided, using marking and reclassification on a per-packet basis by source and destination IP address,
MAC address, or Layer 4 TCP/UDP port number.
●
Cisco Control-plane and Data-plane QoS ACLs on all ports help ensure proper marking on a per-packet
basis.
●
Four Egress Queues Per Port help enable differentiated management of different traffic types across the
stack.
●
Shaped Round Robin (SRR) scheduling helps ensure differential prioritization of packet flows by intelligently
servicing the ingress queues and egress queues.
●
Weighted Tail Drop (WTD) provides congestion avoidance at the ingress and egress queues before a
disruption occurs.
●
Strict Priority Queuing helps ensure that the highest-priority packets are serviced ahead of all other traffic.
●
Trusted Boundary provides the ability to trust the QoS priority settings if an IP phone is present and to
disable the trust setting if the IP phone is removed, thereby preventing a malicious user
●
Rate Limiting is provided based on source and destination IP address, source and destination MAC address,
Layer 4 TCP/UDP information, or any combination of these fields, using QoS ACLs (IP ACLs or MAC ACLs),
class maps, and policy maps.
●
Up to 64 Aggregate or Individual Policers are available per Fast Ethernet or GbE port.
Location Awareness and Mobility
In order to provide delivery of a best-in-class network experience to end users, it is critical for network access to be
location aware. A wide variety of devices can appear on the network, both wired (switches, routers, IP phones, PCs,
access points, controllers, video digital media players, and so on) and wireless (mobile devices, wireless tags,
rogues, and so on). In many industries, locating assets is primarily a manual process and is time consuming and
error prone. The inability to locate assets in real time and to help ensure their availability when and where they are
needed limits reaction time and efficiency.
Location services answer business-critical questions about both mobile assets and the users of those assets
regardless of whether those assets are connecting using wired or wireless, and hence directly improve their
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 10 of 26
Data Sheet
organization’s profitability. Network Location Services also improve security and accelerate client troubleshooting by
locating an asset, user, or device on the network.
●
Network Visibility and Control provide centralized visibility into wired and wireless devices on the network
and their location.
●
Location-Assisted Client Troubleshooting enables tracking of wired or wireless clients for quick problem
resolution.
●
Asset Tracking and Improved Security provide centralized inventory of wired and wireless devices and
asset management for improved business processes.
●
Location-Based Policy allows greater control and visibility. With EnergyWise, power policies can be set up
(to reduce the power or shut down the power from a port) based on the location.
●
Cisco Emergency Responder enhances emergency calling from Cisco Unified CallManager. It helps assure
that Cisco Unified CallManager sends emergency calls to the appropriate Public Safety Answering Point
(PSAP) for the caller’s location.
Tables 4, 5, 6, 7, and 8 provide hardware features, power specifications, management and standards support, and
safety and compliance information for the Cisco Catalyst 2960-S and 2960 Series Switches with LAN Base software.
Table 4.
Cisco Catalyst 2960-S and 2960 Series Switches with LAN Base Software Switch Performance and
Scalability information
Performance and Scalability Numbers for All Switch Models
Cisco Catalyst 2960-S
Cisco Catalyst 2960
88 Gbps
16 Gbps
20 Gbps for FlexStack Stacking
32 Gbps (2960G)
Switching Bandwidth
176 Gbps
32Gbps
Flash Memory
64 MB
32 MB
Memory DRAM
128 MB
64 MB
Cisco Catalyst 2960-S
Cisco Catalyst 2960
Max VLANs
255
255
VLAN IDs
4000
4000
Maximum Transmission Unit (MTU)
Up to 9000 bytes
Up to 9000 bytes
Jumbo Frames
9018 bytes
9018 bytes (2960G only)
Forwarding Bandwidth
*
32 Gbps (2960G)
Forwarding Rate: 64-Byte Packet Cisco Catalyst 2960-S
Cisco Catalyst 2960S-48FPD-L
101.2 mpps
Cisco Catalyst 2960S-48LPD-L
101.2 mpps
Cisco Catalyst 2960S-24PD-L
65.5 mpps
Cisco Catalyst 2960S-48TD-L
101.2 mpps
Cisco Catalyst 2960S-24TD-L
65.5 mpps
Cisco Catalyst 2960S-48FPS-L
77.4 mpps
Cisco Catalyst 2960S-48LPS-L
77.4 mpps
Cisco Catalyst 2960S-24PS-L
41.7 mpps
Cisco Catalyst 2960S-48TS-L
77.4 mpps
Cisco Catalyst 2960S-24TS-L
41.7 mpps
Forwarding Rate: 64-Byte Packet Cisco Catalyst 2960
Cisco Catalyst 2960PD-8TT-L
2.7 mpps
Cisco Catalyst 2960-8TC-L
2.7 mpps
Cisco Catalyst 2960-24TT-L
6.5 mpps
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 11 of 26
Data Sheet
Performance and Scalability Numbers for All Switch Models
Cisco Catalyst 2960-S
*
Cisco Catalyst 2960
Cisco Catalyst 2960-24TC-L
6.5 mpps
Cisco Catalyst 2960-24LT-L
6.5 mpps
Cisco Catalyst 2960-24PC-L
6.5 mpps
Cisco Catalyst 2960-48TT-L
10.1 mpps
Cisco Catalyst 2960-48TC-L
10.1 mpps
Cisco Catalyst 2960-48PST-L
13.3 mpps
Cisco Catalyst 2960G-8TC-L
11.9 mpps
Cisco Catalyst 2960G-24TC-L
35.7 mpps
Cisco Catalyst 2960G-48TC-L
39.0 mpps
Resource: Cisco Catalyst 2960-S and 2960
Default
QoS
Dual
Unicast MAC Addresses
8000
8000
8000
IPv4 IGMP Groups
255
255
255
IPv4 MAC QoS Access Control Entries (ACEs)
128
384
0
IPv4 MAC Security ACEs
384
128
256
Switching bandwidth is maximum Switching capacity.
Table 5.
Dimensions, Weight, Acoustic, MTBF, and Environmental Range
Dimensions (H x W x D)
Cisco Catalyst 2960-S
Inches
Centimeters
Cisco Catalyst 2960S-48FPD-L
1.75 x 17.5 x 15.2
4.5 x 44.5 x 38.6
1.75 x 17.5 x 11.8
4.5 x 44.5 x 29.9
1.75 x 17.5 x 15.2
4.5 x 44.5 x 38.6
1.75 x 17.5 x 11.8
4.5 x 44.5 x 29.9
Cisco Catalyst 2960S-48LPD-L
Cisco Catalyst 2960S-24PD-L
Cisco Catalyst 2960S-48TD-L
Cisco Catalyst 2960S-24TD-L
Cisco Catalyst 2960S-48FPS-L
Cisco Catalyst 2960S-48LPS-L
Cisco Catalyst 2960S-24PS-L
Cisco Catalyst 2960S-48TS-L
Cisco Catalyst 2960S-24TS-L
Cisco Catalyst 2960
Inches
Centimeters
Cisco Catalyst 2960PD-8TT-L
1.73 x 10.6 x 6.2
4.4 x 27 x 15.7
Cisco Catalyst 2960-8TC-L
1.73 x 10.6 x 6.4
4.4 x 27 x 16.3
Cisco Catalyst 2960-24TT-L
1.73 x 17.5 x 9.3
4.4 x 44.5 x 23.6
1.73 x 17.5 x 13
4.4 x 44.5 x 33.2
Cisco Catalyst 2960-48PST-L
1.73 x 17.5 x 9.3
4.4 x 44.5 x 23.6
Cisco Catalyst 2960G-8TC-L
1.73 x 10.6 x 8.1
4.4 x 27 x 20.5
Cisco Catalyst 2960G-24TC-L
1.73 x 17.5 x 12.9
4.4 x 44.5 x 32.8
Pounds
Kilograms
Cisco Catalyst 2960-24TC-L
Cisco Catalyst 2960-24LT-L
Cisco Catalyst 2960-24PC-L
Cisco Catalyst 2960-48TT-L
Cisco Catalyst 2960-48TC-L
Cisco Catalyst 2960G-48TC-L
Weight
Cisco Catalyst 2960-S
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 12 of 26
Data Sheet
Dimensions (H x W x D)
Cisco Catalyst 2960-S
Inches
Centimeters
Cisco Catalyst 2960S-48FPD-L
13
5.9
Cisco Catalyst 2960S-48LPD-L
12.5
5.7
Cisco Catalyst 2960S-24PD-L
12.5
5.7
Cisco Catalyst 2960S-48TD-L
9.5
4.3
Cisco Catalyst 2960S-24TD-L
9.5
4.3
Cisco Catalyst 2960S-48FPS-L
13
5.9
Cisco Catalyst 2960S-48LPS-L
12.5
5.7
Cisco Catalyst 2960S-24PS-L
12.5
5.7
Cisco Catalyst 2960S-48TS-L
10.5
4.8
Cisco Catalyst 2960S-24TS-L
10
4.5
Cisco Catalyst 2960
Pounds
Kilograms
Cisco Catalyst 2960PD-8TT-L
3
1.4
Cisco Catalyst 2960-8TC-L
3
1.4
Cisco Catalyst 2960-24TT-L
8
3.6
Cisco Catalyst 2960-24TC-L
8
3.6
Cisco Catalyst 2960-24LT-L
10
4.5
Cisco Catalyst 2960-24PC-L
12
5.4
Cisco Catalyst 2960-48TT-L
8
3.6
Cisco Catalyst 2960-48TC-L
8
3.6
Cisco Catalyst 2960-48PST-L
12
5.4
Cisco Catalyst 2960G-8TC-L
3
1.4
Cisco Catalyst 2960G-24TC-L
10
4.5
Cisco Catalyst 2960G-48TC-L
12
5.4
Cisco Catalyst 2960-S
Cisco Catalyst 2960
Environmental Ranges
Fahrenheit
Centigrade
Fahrenheit
Centigrade
Operating Temperature up to 5000 ft (1500 m)
0º to 113ºF
-5º to 45ºC
23º to 113ºF
-5º to 45ºC
Operating Temperature up to 10,000 ft (3000 m)
23º to 104ºF
-5º to 40ºC
23º to 104ºF
-5º to 40ºC
23º to 131ºF
-5º to 55ºC
23º to 131ºF
-5º to 55ºC
Short-term Exception up to 5000 ft (1500 m)
23º to 122ºF
-5º to 50ºC
23º to 122ºF
-5º to 50ºC
Short-term Exception up to 10,000 ft (3000 m)*
23º to 113ºF
-5º to 45ºC
23º to 113ºF
-5º to 45ºC
*
Short-term Exception at Sea Level
*
*
Short-term Exception up to 13,000 ft (4000 m)
23º to 104ºF
-5º to +40ºC
23º to 104ºF
-5º to 40ºC
Storage Temperature up to 15,000 ft (4573 m)
-13º to 158ºF
-25º to 70ºC
-13º to 158ºF
-25º to 70ºC
Feet
Meters
Operating Altitude
Up to 10,000
Up to 3000
Up to 10,000
Up to 3000
Operating Relative Humidity
10% to 95% noncondensing
10% to 95% noncondensing
Storage Relative Humidity
10% to 95% noncondensing
10% to 95% noncondensing
Acoustic Noise
Measured per ISO 7779 and Declared per ISO 9296.
Bystander Positions Operating Mode at 25°C ambient.
Sound Pressure
Model
LpA (Typical)
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Sound Power
LpAD (Maximum)
LwA (Typical)
LwAD (Maximum)
Page 13 of 26
Data Sheet
Dimensions (H x W x D)
Cisco Catalyst 2960-S
Inches
Centimeters
Cisco Catalyst 2960S-48FPD-L
Cisco Catalyst 2960S-48LPD-L
42 dB
45 dB
5.2 B
5.5 B
44 dB
47 dB
5.4 B
5.7 B
42 dB
45 dB
5.2 B
5.5 B
44 dB
47 dB
5.4 B
5.7 B
Cisco Catalyst 2960S-24PD-L
Cisco Catalyst 2960S-48TD-L
Cisco Catalyst 2960S-24TD-L
Cisco Catalyst 2960S-48FPS-L
Cisco Catalyst 2960S-48LPS-L
Cisco Catalyst 2960S-24PS-L
Cisco Catalyst 2960S-48TS-L
Cisco Catalyst 2960S-24TS-L
Mean Time Between Failures (MTBF)
Cisco Catalyst 2960-S
*
Cisco Catalyst 2960
Model
MTBF in hours
Model
MTBF in hours
Cisco Catalyst 2960S-48FPD-L
183,498
Cisco Catalyst 2960PD-8TT-L
737,065
Cisco Catalyst 2960S-48LPD-L
198,300
Cisco Catalyst 2960-8TC-L
615,549
Cisco Catalyst 2960S-24PD-L
237,016
Cisco Catalyst 2960-24TT-L
407,707
Cisco Catalyst 2960S-48TD-L
311,291
Cisco Catalyst 2960-24TC-L
339,743
Cisco Catalyst 2960S-24TD-L
332,958
Cisco Catalyst 2960-24LT-L
402,926
Cisco Catalyst 2960S-48FPS-L
189,242
Cisco Catalyst 2960-24PC-L
311,781
Cisco Catalyst 2960S-48LPS-L
205,052
Cisco Catalyst 2960-48TT-L
243,277
Cisco Catalyst 2960S-24PS-L
245,604
Cisco Catalyst 2960-48TC-L
336,409
Cisco Catalyst 2960S-48TS-L
328,058
Cisco Catalyst 2960-48PST-L
180,427
Cisco Catalyst 2960S-24TS-L
349,824
Cisco Catalyst 2960G-8TC-L
485,576
Cisco Catalyst 2960S-STACK
25,743,890
Cisco Catalyst 2960G-24TC-L
313,828
Cisco Catalyst 2960G-48TC-L
221,432
Not more than the following in a 1-year period: 96 consecutive hours, or 360 hours total, or 15 occurrences.
Note:
Table 6.
For Cisco Catalyst 2960G-8TC-L, reduce the high range temperature by 5°C.
Connectors, LED Indicators, and Dimensions
Connectors and LED Indicators
Cisco Catalyst 2960-S with SFP+ based ports:
● 10BASE-T ports: RJ-45 connectors, 2-pair Category 3, 4, or 5 unshielded twisted-pair (UTP) cabling
● 100BASE-TX ports: RJ-45 connectors, 2-pair Category 5 UTP cabling
● 1000BASE-T ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-T SFP-based ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-SX, -LX/LH, -ZX, -BX, -T,* -FX,* and coarse wavelength-division multiplexing (CWDM) SFP-based ports: LC fiber connectors
(single/multimode fiber)
● 10GBASE-LR, SR, LRM, CX1 SFP+ based ports
*
The Cisco Catalyst 2960-S with SFP+ does not support the GLC-FE-100BX, GLC-FE-100FX, GLC-T, or GLC-FE-100LX.
Cisco Catalyst 2960-S and 2960 with SFP-based ports:
● 10BASE-T ports: RJ-45 connectors, 2-pair Category 3, 4, or 5 UTP cabling
● 100BASE-TX ports: RJ-45 connectors, 2-pair Category 5 UTP cabling
● 1000BASE-T ports: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-T SFP-based ports**: RJ-45 connectors, 4-pair Category 5 UTP cabling
● 1000BASE-SX -LX/LH, -ZX, -BX, -T,* -FX,* and CWDM SFP-based ports: LC fiber connectors (single/multimode fiber)
● 100BASE-LX, -BX, -FX SFP-based ports: LC fiber connectors (single/multimode fiber)
*
GLC-T and GLC-GE-100FX are not supported on the Cisco Catalyst 2960-8TC-S, 2960-8TC-L, or 2960G-8TC-L switches.
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 14 of 26
Data Sheet
Connectors and LED Indicators
**
1000BASE-T not supported on Cisco Catalyst 2960-S switches.
Cisco Catalyst 2960-S FlexStack stacking cables:
CAB-STK-E-0.5M
FlexStack stacking cable with a 0.5 m length
CAB-STK-E-1M
FlexStack stacking cable with a 1.0 m length
CAB-STK-E-3M
FlexStack stacking cable with a 3.0 m length
Cisco Catalyst 2960-S console cables:
CAB-CONSOLE-RJ45
Console cable 6 ft with RJ-45
CAB-CONSOLE-USB
Console cable 6 ft with USB Type A and mini-B connectors
● Customers can provide power to a switch by using the internal power supply. The connector is located at the back of the switch. These switches do
not have a redundant-power-supply port.
● The internal power supply is an auto-ranging unit
● The internal power supply supports input voltages between 100 and 240 VAC
● Use the supplied AC power cord to connect the AC power connector to an AC power outlet.
● Cisco RPS connector:
The Cisco RPS connector offers connection for an optional Cisco RPS 2300 that uses AC input and supplies DC output to the switch.
The connector offers a 2300W redundant power system that supports up to 6 external network devices and provides power to 2 failed devices at a
time.
The connector automatically senses when the internal power supply of a connected device fails and provides power to the failed device, preventing
loss of network traffic.
Only the Cisco RPS 2300 (model PWR-RPS2300) should be attached to the redundant-power-system receptacle.
Note: The Cisco Catalyst 2960-8TC-L and 2960G-8TC-L do not have RPS ports.
● Per-port status: Link integrity, disabled, activity, speed, and full duplex
● System status: System, RPS, link status, link duplex, PoE, and link speed
Table 7.
Description
Management and Standards Support for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Base Software
Specification
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 15 of 26
Data Sheet
Description
Management
Specification
● BRIDGE-MIB
● CISCO-CABLE-DIAG-MIB
● CISCO-TC-MIB
● CICSO-TCP-MIB
● CISCO-CDP-MIB
● CISCO-CLUSTER-MIB
● CISCO-UDLDP-MIB
● CISCO-VLAN-IFTABLE
● CISCO-CONFIG-COPY-MIB
● CISCO-CONFIG-MAN-MIB
● RELATIONSHIP-MIB
● CISCO-VLAN-MEMBERSHIP-MIB
● CISCO-DHCP-SNOOPING-MIB
● CISCO-ENTITY-VENDORTYPE-OID-MIB
● CISCO-VTP-MIB
● ENTITY-MIB
● CISCO-ENVMON-MIB
● CISCO-ERR-DISABLE-MIB
● ETHERLIKE-MIB
● IEEE8021-PAE-MIB
● CISCO-FLASH-MIB
● CISCO-FTP-CLIENT-MIB
● IEEE8023-LAG-MIB
● IF-MIB
● CISCO-IGMP-FILTER-MIB
● CISCO-IMAGE-MIB
● INET-ADDRESS-MIB
● OLD-CISCO-CHASSIS-MIB
● CISCO-IP-STAT-MIB
● CISCO-LAG-MIB
● OLD-CISCO-FLASH-MIB
● OLD-CISCO-INTERFACES-MIB
● CISCO-MAC-NOTIFICATION-MIB
● CISCO-MEMORY-POOL-MIB
● OLD-CISCO-IP-MIB
● OLD-CISCO-SYS-MIB
● CISCO-PAGP-MIB
● CISCO-PING-MIB
● OLD-CISCO-TCP-MIB
● OLD-CISCO-TS-MIB
● CISCO-POE-EXTENSIONS-MIB
● CISCO-PORT-QOS-MIB
● RFC1213-MIB
● RMON-MIB
● CISCO-PORT-SECURITY-MIB
● CISCO-PORT-STORM-CONTROL-MIB
● RMON2-MIB
● SNMP-FRAMEWORK-MIB
● CISCO-PRODUCTS-MIB
● CISCO-PROCESS-MIB
● SNMP-MPD-MIB
● SNMP-NOTIFICATION-MIB
● CISCO-RTTMON-MIB
● CISCO-SMI-MIB
● SNMP-TARGET-MIB
● SNMPv2-MIB
● CISCO-STP-EXTENSIONS-MIB
● CISCO-SYSLOG-MIB
● TCP-MIB
● UDP-MIB
● ePM MIB
● CISCO-STACKWISE-MIB (2960-S)
Standards
● IEEE 802.1D Spanning Tree Protocol
● IEEE 802.1p CoS Prioritization
● 100BASE-BX (SFP)
● 100BASE-FX (SFP)
● IEEE 802.1Q VLAN
● IEEE 802.1s
● 100BASE-LX (SFP)
● 1000BASE-BX (SFP)
● IEEE 802.1w
● IEEE 802.1X
● 1000BASE-SX (SFP)
● 1000BASE-LX/LH (SFP)
● IEEE 802.1ab (LLDP)
● IEEE 802.3ad
● 1000BASE-ZX (SFP)
● 1000BASE-CWDM SFP 1470 nm
● IEEE 802.3af
● IEEE 802.3ah (100BASE-X single/multimode
fiber only)
● IEEE 802.3x full duplex on 10BASE-T, 100BASE-TX,
and 1000BASE-T ports
● IEEE 802.3 10BASE-T specification
● 1000BASE-CWDM SFP 1490 nm
● 1000BASE-CWDM SFP 1510 nm
● IEEE 802.3u 100BASE-TX specification
● IEEE 802.3ab 1000BASE-T specification
● IEEE 802.3z 1000BASE-X specification
● 1000BASE-CWDM SFP 1530 nm
● 1000BASE-CWDM SFP 1550 nm
● 1000BASE-CWDM SFP 1570 nm
● 1000BASE-CWDM SFP 1590 nm
● 1000BASE-CWDM SFP 1610 nm
● 10GBASE-LR (SFP+)
● 10GBASE-SR (SFP+)
● 10GBASE-LRM (SFP+)
● 10GBASE-CX1 (SFP+)
● RMON I and II standards
● SNMP v1, v2c, and v3
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 16 of 26
Data Sheet
Description
Specification
RFC Compliance
● RFC 768 - UDP
● RFC 783 - TFTP
● RFC 1901 - SNMP v2C
● RFC 1902-1907 - SNMP v2
● RFC 791 - IP
● RFC 792 - ICMP
● RFC 1981 - Maximum Transmission Unit (MTU) Path
Discovery IPv6
● FRC 2068 - HTTP
● RFC 793 - TCP
● RFC 826 - ARP
● RFC 2131 - DHCP
● RFC 2138 - RADIUS
● RFC 854 - Telnet
● RFC 951 - Bootstrap Protocol (BOOTP)
● RFC 2233 - IF MIB v3
● RFC 2373 - IPv6 Aggregatable Addrs
● RFC 959 - FTP
● RFC 1112 - IP Multicast and IGMP
● RFC 2460 - IPv6
● RFC 2461 - IPv6 Neighbor Discovery
● RFC 1157 - SNMP v1
● RFC 1166 - IP Addresses
● RFC 1256 - Internet Control Message Protocol (ICMP)
Router Discovery
● RFC 1305 - NTP
Table 8.
● RFC 2462 - IPv6 Autoconfiguration
● RFC 2463 - ICMP IPv6
● RFC 2474 - Differentiated Services (DiffServ) Precedence
● RFC 2597 - Assured Forwarding
● RFC 1492 - TACACS+
● RFC 1493 - Bridge MIB
● RFC 2598 - Expedited Forwarding
● RFC 2571 - SNMP Management
● RFC 1542 - BOOTP extensions
● RFC 1643 - Ethernet Interface MIB
● RFC 3046 - DHCP Relay Agent Information Option
● RFC 3376 - IGMP v3
● RFC 1757 - RMON
● RFC 3580 - 802.1X RADIUS
Voltage and Power Information
AC/DC Input Voltage and Current
Cisco Catalyst 2960-S
Voltage (Autoranging)
Current
Frequency
Cisco Catalyst 2960S-48FPD-L
100 to 240 VAC
9 to 4 A
50 to 60Hz
Cisco Catalyst 2960S-48LPD-L
5 to 2 A
Cisco Catalyst 2960S-24PD-L
5 to 2 A
Cisco Catalyst 2960S-48TD-L
1 to 0.5 A
Cisco Catalyst 2960S-24TD-L
1 to 0.5 A
Cisco Catalyst 2960S-48FPS-L
9 to 4 A
Cisco Catalyst 2960S-48LPS-L
5 to 2 A
Cisco Catalyst 2960S-24PS-L
5 to 2 A
Cisco Catalyst 2960S-48TS-L
1 to 0.5 A
Cisco Catalyst 2960S-24TS-L
1 to 0.5 A
Cisco Catalyst 2960
Voltage (Autoranging)
Current
Frequency
Cisco Catalyst 2960-8TC-L
100 to 240 VAC
0.5 to 0.25 A
50 to 60Hz
Cisco Catalyst 2960G-8TC-L
0.8 to 0.4 A
Cisco Catalyst 2960-24LT-L
3.0 to 1.5 A
Cisco Catalyst 2960-24PC-L
8.0 to 4.0 A
Cisco Catalyst 2960-48PST-L
5.0 to 2.0 A
Cisco Catalyst 2960-24TT-L and Cisco Catalyst 2960-24TC-L and
Cisco Catalyst 2960-48TT-L and Cisco Catalyst 2960-48TC-L
1.3 to 0.8 A
Cisco Catalyst 2960G-24TC-L and Cisco Catalyst 2960G-48TC-L
3.0 to 1.5 A
Cisco Catalyst 2960PD-8TT-L
DC input 48 VDC
0.3 A
(for AC use PWR-A= sold separately)
Power Rating
Cisco Catalyst 2960-S
Cisco Catalyst 2960
Model
Power Rating
Model
Cisco Catalyst 2960S-48FPD-L
0.89 kVA
Cisco Catalyst 2960PD-8TT-L
11W
Cisco Catalyst 2960S-48LPD-L
0.48 kVA
Cisco Catalyst 2960-8TC-L
0.035 kVA
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Power Rating
Page 17 of 26
Data Sheet
AC/DC Input Voltage and Current
Cisco Catalyst 2960S-24PD-L
0.46 kVA
Cisco Catalyst 2960-24TT-L
0.05 kVA
Cisco Catalyst 2960S-48TD-L
0.09 kVA
Cisco Catalyst 2960-48TT-L
0.075 kVA
Cisco Catalyst 2960S-24TD-L
0.09 kVA
Cisco Catalyst 2960-24TC-L
0.05 kVA
Cisco Catalyst 2960S-48FPS-L
0.89 kVA
Cisco Catalyst 2960-24LT-L
0.175 kVA
Cisco Catalyst 2960S-48LPS-L
0.48 kVA
Cisco Catalyst 2960-24PC-L
0.470 kVA
Cisco Catalyst 2960S-24PS-L
0.46 kVA
Cisco Catalyst 2960-48PST-L
0.5 kVA
Cisco Catalyst 2960S-48TS-L
0.13 kVA
Cisco Catalyst 2960-48TC-L
0.075 kVA
Cisco Catalyst 2960S-24TS-L
0.09 kVA
Cisco Catalyst 2960G-8TC-L
0.05 kVA
Cisco Catalyst 2960G-24TC-L
0.075 kVA
Cisco Catalyst 2960G-48TC-L
0.140 kVA
DC Input Voltages (RPS Input)
Cisco Catalyst 2960-S
Cisco Catalyst 2960S-48FPD-L
12V at 4 A
-52 V at 15 A
Cisco Catalyst 2960S-48LPD-L
12V at 4 A
-52 V at 8 A
Cisco Catalyst 2960S-24PD-L
12V at 3 A
-52 V at 8 A
Cisco Catalyst 2960S-48TD-L
12V at 4 A
N/A
Cisco Catalyst 2960S-24TD-L
12V at 3 A
N/A
Cisco Catalyst 2960S-48FPS-L
12V at 4 A
-52 V at 15A
Cisco Catalyst 2960S-48LPS-L
12V at 4 A
-52 V at 8 A
Cisco Catalyst 2960S-24PS-L
12V at 3 A
-52 V at 8 A
Cisco Catalyst 2960S-48TS-L
12V at 4 A
N/A
Cisco Catalyst 2960S-24TS-L
12V at 4 A
N/A
12V at 5 A
5A
Cisco Catalyst 2960-24LT-L
12 V at 8.3 A
-48 V at 2.7 A
Cisco Catalyst 2960-24PC-L
12 V at 11.25 A
-48 V at 7.8 A
Cisco Catalyst 2960-48PST-L
12 V at 4 A
-48 V at 7.8 A
Cisco Catalyst 2960-48TC-L
12 V at 5 A
Cisco Catalyst 2960G-24TC-L
12 V at 10.5
Cisco Catalyst 2960-S
Cisco Catalyst 2960-24TT-L
Cisco Catalyst 2960-48TT-L
Cisco Catalyst 2960-24TC-L
Cisco Catalyst 2960G-48TC-L
No RPS input for Cisco Catalyst 2960PD-8TT-L, Cisco Catalyst 2960-8TC-L, or Cisco Catalyst 2960G-8TC-L.
PoE and PoE+
● Maximum power supplied per port for PoE+ is 30W.
● Maximum power supplied per port for PoE is 15.4W.
● Total power dedicated to PoE or PoE+ is 370W or 740W.
Table 9.
Power Specifications for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Base Software
Description
C2960-S Specifications
Models
C2960S-48FPD-L
C2960S-48LPD-L
C2960S-24PD-L
C2960S-48TD-L
C2960S-24TD-L
71W
55W
55W
39W
70W
54W
53W
38W
100 Percent Throughput
Measured Power Consumption 81W
5 Percent Throughput
Measured Power Consumption 80W
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 18 of 26
Data Sheet
5 Percent Throughput (with 50 Percent PoE Loads)
Measured Power Consumption Switch Power: 464W
PoE Power: 386W
Switch Power: 266W
Switch Power: 249W
PoE Power: 195W
PoE Power: 195W
-
-
-
-
100 Percent Throughput (with Maximum Possible PoE Loads)
Measured Power Consumption Switch Power: 870W
PoE Power: 744W
Switch Power: 466W
Switch Power: 451W
PoE Power: 375W
PoE Power: 375W
Description
C2960-S Specifications
Models
C2960S-48FPS-L
C2960S-48LPS-L
C2960S-24PS-L
C2960S-48TS-L
C2960S-24TS-L
71W
55W
52W
40W
70W
54W
50W
39W
Switch Power: 266W
Switch Power: 249W
-
-
PoE Power: 375W
PoE Power: 375W
-
-
100 Percent Throughput
Measured Power Consumption 79W
5 Percent Throughput
Measured Power Consumption 78W
5 Percent Throughput (with 50 Percent PoE Loads)
Measured Power Consumption Switch Power: 463W
PoE Power: 744W
100 Percent Throughput (with Maximum Possible PoE Loads)
Measured Power Consumption Switch Power: 870W
PoE Power: 744W
Description
C2960 Specifications
Models
C2960-48PST-L
Switch Power: 466W
Switch Power: 449W
PoE Power: 375W
PoE Power: 375W
C2960-24PC-L
C2960-24LT-L
C2960-48TC-L
C2960-24TC-L
45W
36W
39W
27W
43W
34W
36W
24W
Switch Power: 237W
Switch Power: 98W
-
-
PoE Power: 185W
PoE Power: 62W
-
-
100 Percent Throughput
Measured Power Consumption 67W
5 Percent Throughput
Measured Power Consumption 63W
5 Percent Throughput (with 50 Percent PoE Loads)
Measured Power Consumption Switch Power: 262W
PoE Power: 187W
100 Percent Throughput (with Maximum Possible PoE Loads)
Measured Power Consumption Switch Power: 460W
Switch Power: 433W
Switch Power: 162W
PoE Power: 339W
PoE Power: 357W
PoE Power: 119W
Switch Output: 413W
Switch Output: 259W
Switch Output: 147W
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 19 of 26
Data Sheet
Description
C2960 Specifications
Models
C2960-48TT-L
C2960-24TT-L
C2960G-48TC-L
C2960G-24TC-L
C2960-24T-L
28W
123W
72W
22W
26W
114W
65W
21W
-
-
-
-
-
-
-
100 Percent Throughput
Measured Power Consumption 42W
5 Percent Throughput
Measured Power Consumption 38W
5 Percent Throughput (with 50 Percent PoE Loads)
Measured Power Consumption -
100 Percent Throughput (with Maximum Possible PoE Loads)
Measured Power Consumption -
-
Description
C2960 Specifications
Models
C2960-8TC-L
C2960PD-8TT-L
C2960G-8TC-L
20W
11W
36W
20W
11W
36W
11W
36W
11W
36W
100 Percent Throughput
Measured Power Consumption
5 Percent Throughput
Measured Power Consumption
5 Percent Throughput (with 50 Percent PoE Loads)
Measured Power Consumption
20W
100 Percent Throughput (with Maximum Possible PoE Loads)
Measured Power Consumption
Note:
20W
Disclaimer: All power consumption numbers were measured under controlled laboratory conditions and are
provided as an estimate.
The wattage rating on the power supply does not represent actual power draw. It indicates the maximum power draw
possible by the power supply. This rating can be used for facility capacity planning. For PoE switches, cooling
requirements are smaller than the actual power consumption as a significant portion of PoE loads are dissipated in
the endpoints.
Non-PoE Power Consumption
100 Percent Throughput Switch Power Consumption
The numbers indicate the power consumed by a typical switch under normal conditions. Normal conditions signify a
temperature of 25 degrees Celsius, atmospheric pressure in the range of 860 to 1060 mbar, and relative humidity
from 30 to 75 percent. Typically such power draws are only seen when encountering a 100 percent traffic load made
up entirely of 64-byte packets on the switch and the uplinks.
5 Percent Throughput Switch Power Consumption
The numbers indicate the power consumed by a typical switch under normal conditions. Normal conditions signify a
temperature of 25 degrees Celsius, atmospheric pressure in the range of 860 to 1060 mbar, and relative humidity
from 30 to 75 percent. The numbers below indicate a 5 percent traffic load on the switch and its uplinks.
PoE Power Consumption
100 Percent Throughput Switch Power Consumption (No PoE Loads)
The numbers indicate the power consumed by a typical switch under normal conditions. Normal conditions signify a
temperature of 25 degrees Celsius, atmospheric pressure in the range of 860 to 1060 mbar, and relative humidity
from 30 to 75 percent. Typically such power draws are only seen when encountering a 100 percent traffic load made
up entirely of 64-byte packets with no PoE loads on the switch and uplinks.
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 20 of 26
Data Sheet
Measured 5 Percent Throughput Switch Power Consumption (No PoE Loads)
The numbers indicate the power consumed by a typical switch under normal conditions. Normal conditions signify a
temperature of 25 degrees Celsius, atmospheric pressure in the range of 860 to 1060 mbar and relative humidity
from 30 to 75 percent. The numbers below indicate a 5 percent traffic load on the switch and its uplinks
100 Percent Throughput Switch Power Consumption (with Maximum PoE Loads)
The numbers indicate the power consumed by a typical system (the switch and the corresponding PoE loads) under
normal conditions. Normal conditions signify a temperature of 25 degrees Celsius, atmospheric pressure in the
range of 860 to 1060 mbar and relative humidity from 30 to 75 percent. Typically this power draw is realized when a
switch is running 100 percent traffic load of 64 byte sized packets on all its ports and uplinks and also drawing 100
percent PoE load.
5 Percent Throughput Switch Power Consumption (with 50 Percent PoE Loads)
The numbers indicate the power consumed by a typical system (the switch and the corresponding PoE loads) under
normal conditions. Normal conditions signify a temperature of 25 degrees Celsius, atmospheric pressure in the
range of 860 to 1060 mbar and relative humidity from 30 to 75 percent. The numbers below indicate a 5 percent
traffic load and 50 percent PoE load on the switch and its uplinks.
Table 10.
Safety and Compliance
Description
Safety Certifications
Specification
● UL 60950-1, Second Edition
● CAN/CSA 22.2 No. 60950-1, Second Edition
● TUV/GS to EN 60950-1, Second Edition
● CB to IEC 60950-1 Second Edition with all country deviations
● CE Marking
● NOM (through partners and distributors)
Electromagnetic Emissions
Certifications
● FCC Part 15 Class A
● EN 55022 Class A (CISPR22)
● EN 55024 (CISPR24)
● AS/NZS CISPR22 Class A
● VCCI Class A
● CE
● CNS13438 Class A
● MIC
● GOST
● China EMC Certifications
Environmental
Reduction of Hazardous Substances (ROHS) 5
Telco
Common Language Equipment Identifier (CLEI) code
Warranty
Limited lifetime warranty
Cisco Limited Lifetime Hardware Warranty
Cisco Catalyst 2960-S and 2960 Series Switches come with a limited lifetime warranty (Table 11). The warranty for
the Cisco 2960-S Series switches has the same terms as our standard limited lifetime warranty plus the addition of
next business day delivery of replacement hardware where available and 90 days of 8x5 Cisco Technical Assistance
Center (TAC) support.
Your formal warranty statement, including the warranty applicable to Cisco software, appears in the Cisco
information packet that accompanies your Cisco product. We encourage you to review carefully the warranty
statement shipped with your specific product before use.
Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.
For further information on warranty terms, visit http://www.cisco.com/go/warranty.
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 21 of 26
Data Sheet
Table 11.
Limited Lifetime Warranty Terms
Cisco Limited Lifetime Hardware Warranty
Cisco Enhanced Limited Lifetime Hardware Warranty
Device Covered
Applies to Cisco Catalyst 2960 Series Switches sold on
or after May 1, 2009
Applies to Cisco Catalyst 2960-S Series Switches
Warranty Duration
As long as the original end user continues to own or use
As long as the original end user continues to own or use
the product, provided that: fan and power supply warranty the product, provided that: fan and power supply warranty
is limited to five (5) years.
is limited to five (5) years.
End-of-life policy
In the event of discontinuance of product manufacture,
In the event of discontinuance of product manufacture,
Cisco warranty support is limited to five (5) years from the Cisco warranty support is limited to five (5) years from the
announcement of discontinuance.
announcement of discontinuance.
Hardware replacement
Cisco or its service center will use commercially
reasonable efforts to ship a replacement part within ten
(10) working days after receipt of the RMA request.
Actual delivery times might vary depending on customer
location.
Cisco or its service center will use commercially
reasonable efforts to ship a replacement for next
business day delivery, where available. Otherwise, a
replacement will be shipped within ten (10) working days
after receipt of the RMA request. Actual delivery times
might vary depending on customer location.
Effective date
Hardware warranty commences from the date of
shipment to customer (and in case of resale by a Cisco
reseller, not more than ninety [90] days after original
shipment by Cisco).
Hardware warranty commences from the date of
shipment to customer (and in case of resale by a Cisco
reseller, not more than ninety [90] days after original
shipment by Cisco).
TAC support
Not included.
Cisco will provide during customer’s local business
hours, 8 hours per day, 5 days per week basic
configuration, diagnosis, and troubleshooting of devicelevel problems for up to 90 days from the date of
shipment of the originally purchased Cisco Catalyst 2960S product. This support does not include solution or
network-level support beyond the specific device under
consideration.
Cisco.com Access
Warranty allows guest access only to Cisco.com
Warranty allows guest access only to Cisco.com
Software Update Policy for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Base Software
Customers with Cisco Catalyst LAN Base software licenses will be provided with maintenance updates and bug fixes
designed to maintain the compliance of the software with published specifications, release notes, and industry
standards compliance as long as the original end user continues to own or use the product or up to one year from
the end-of-sale date for this product, whichever occurs earlier. Customers with licenses for our premium software
images, Enterprise Services or IP Services, require a service support contract such as Cisco SMARTnet Service to
download updates.
This policy supersedes any previous warranty or software statement and is subject to change without notice.
Cisco and Partner Services for the Cisco Catalyst 2960
Minimize operating costs and reduce power consumption with the Cisco Catalyst 2960 Switch using intelligent,
personalized services from Cisco and our partners. Through a discovery process that begins with understanding
your business objectives, we help you integrate the Cisco Catalyst into your architecture and incorporate network
services onto it. Sharing knowledge and leading practices, we support your success every step of the way as you
deploy, absorb, manage, and scale new technology. Choose from a flexible suite of support services designed to
meet your business needs and help you maintain high-quality network performance while controlling operational
costs. Table 12 lists the technical services available for the Cisco Catalyst 2960-S and 2960 Series Switches.
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 22 of 26
Data Sheet
Table 12.
Technical Services Available for Cisco Catalyst 2960-S and 2960 Series Switches
Technical Services
Cisco SMARTnet Service
● Around-the-clock, global access to the Cisco TAC
● Unrestricted access to the extensive Cisco.com knowledge base and tools
● Next-business-day, 8x5x4, 24x7x4, or 24x7x2 advance hardware replacement and onsite parts replacement and installation available1
● Ongoing operating system software updates within the licensed feature set2
Cisco Smart Foundation Service
● Next-business-day advance hardware replacement as available
● Access to SMB TAC during business hours (access levels vary by region)
● Access to Cisco.com SMB knowledge base
● Online technical resources through Smart Foundation Portal
● Operating system software bug fixes and patches
Cisco Smart Care Service
● Network-level coverage for the needs of small and medium-sized businesses
● Proactive health checks and periodic assessments of Cisco network foundation, voice, and security technologies
● Technical support for eligible Cisco hardware and software through Smart Care Portal
● Cisco operating system and application software updates and upgrades2
● Next-business-day advance hardware replacement as available, 24x7x4 option available1
Cisco SP Base Service
● Around-the-clock, global access to the Cisco TAC
● Registered access to Cisco.com
● Next-business-day, 8x5x4, 24x7x4, and 24x7x2 advance hardware replacement. Return to factory option available1
● Ongoing operating system software updates2
Cisco Focused Technical Support Services
● Three levels of premium, high-touch services are available
● Cisco High-Touch Operations Management Service
● Cisco High-Touch Technical Support Service
● Cisco High-Touch Engineering Service
Valid Cisco SMARTnet or SP Base contracts are required on all network equipment.
Ordering Information
Tables 13, 14, and 15 give ordering information for the Cisco Catalyst 2960-S and 2960 Series Switches with LAN
Base software.
Table 13.
Ordering Information for Cisco Catalyst 2960-S Series Switches with LAN Base Software
Part Numbers
Description
10 Gigabit Uplinks with 10/100/1000 Ethernet Connectivity
WS-C2960S-48FPD-L
● 48 Ethernet 10/100/1000 PoE+ ports
● 740W PoE capacity
● 2 10 Gigabit Ethernet or 2 1 Gigabit Ethernet SFP+ uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
WS-C2960S-48LPD-L
● 48 Ethernet 10/100/1000 PoE+ ports
● 370W PoE capacity
● 2 10 Gigabit Ethernet or 2 1 Gigabit Ethernet SFP+ uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
1
Advance hardware replacement is available in various service-level combinations. For example, 8x5xNBD indicates that shipment
will be initiated during the standard 8-hour business day, 5 days a week (the generally accepted business days within the relevant
region), with next-business-day (NBD) delivery. Where NBD is not available, same day shipping is provided. Restrictions apply;
please review the appropriate service descriptions for details.
2
Cisco operating system updates include the following: maintenance releases, minor updates, and major updates within the
licensed feature set.
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 23 of 26
Data Sheet
Part Numbers
WS-C2960S-24PD-L
Description
● 24 Ethernet 10/100/1000 PoE+ ports
● 370W PoE capacity
● 2 10 Gigabit Ethernet or 2 1 Gigabit Ethernet SFP+ uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
WS-C2960S-48TD-L
● 48 Ethernet 10/100/1000 ports
● 2 10 Gigabit Ethernet or 2 1 Gigabit Ethernet SFP+ uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
WS-C2960S-24TD-L
● 24 Ethernet 10/100/1000 ports
● 2 10 Gigabit Ethernet or 2 1 Gigabit Ethernet SFP+ uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
1 Gigabit Uplinks with 10/100/1000 Ethernet Connectivity
WS-C2960S-48FPS-L
● 48 Ethernet 10/100/1000 PoE+ ports
● 740W PoE capacity
● 4 1 Gigabit Ethernet SFP uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
WS-C2960S-48LPS-L
● 48 Ethernet 10/100/1000 PoE+ ports
● 370W PoE capacity
● 4 1 Gigabit Ethernet SFP uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
WS-C2960S-24PS-L
● 24 Ethernet 10/100/1000 PoE+ ports
● 370W PoE capacity
● 4 1 Gigabit Ethernet SFP uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
WS-C2960S-48TS-L
● 48 Ethernet 10/100/1000 ports
● 4 1 Gigabit Ethernet SFP uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
WS-C2960S-24TS-L
● 24 Ethernet 10/100/1000 ports
● 4 1 Gigabit Ethernet SFP uplink ports
● Optional Cisco FlexStack stacking support
● LAN Base image
C2960S-STACK
Table 14.
Optional FlexStack hot-swappable stacking module, a.5m stack cable is included with the module.
Optional 1m and 3m cables are also available.
Ordering Information for Cisco Catalyst 2960 Series Switches with LAN Base Software
Part Numbers
WS-C2960PD-8TT-L
Description
● 8 Ethernet 10/100 ports and 1 10/100/1000 PoE input port
● Power adaptor (PWR-A=) and power cord sold separately
● Compact size with no fan; magnet included
● LAN Base image
WS-C2960-8TC-L
● 8 Ethernet 10/100 ports
● 1 dual-purpose uplink (dual-purpose uplink port has 1 10/100/1000 Ethernet port,1 SFP-based Gigabit
Ethernet port, 1 port active)
● Compact size with no fan; magnet included
● LAN Base image
WS-C2960-24TT-L
● 24 Ethernet 10/100 ports and 2 10/100/1000 uplinks
● 1 RU fixed-configuration
● LAN Base image
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 24 of 26
Data Sheet
Part Numbers
Description
● 48 Ethernet 10/100 ports and 2 10/100/1000 uplinks
● 1 RU fixed-configuration
WS-C2960-48TT-L
● LAN Base image
● 24 Ethernet 10/100 ports with 8 PoE ports and 2 10/100/1000 uplinks
● 1 RU fixed-configuration
WS-C2960-24LT-L
● LAN Base image
WS-C2960-24PC-L
● 24 Ethernet 10/100 PoE ports and 2 dual-purpose uplinks
● 1 RU fixed-configuration
● LAN Base image
WS-C2960-48PST-L
● 48 Ethernet 10/100 PoE ports and 2 10/100/1000 uplinks and 2 SFP uplinks
● 1 RU fixed-configuration
● LAN Base image
WS-C2960-48TC-L
● 48 Ethernet 10/100 ports and 2 dual-purpose uplinks (each dual-purpose uplink port has 1 10/100/1000
Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
● 1 RU fixed-configuration
● LAN Base image
● 7 Ethernet 10/100/1000 ports and 1 dual-purpose uplink (dual-purpose uplink port has 1 10/100/1000
Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
● Compact size with no fan; magnet included
WS-C2960G-8TC-L
● LAN Base image
● 20 Ethernet 10/100/1000 ports and 4 dual-purpose uplinks (each dual-purpose uplink port has 1
10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
● 1 RU fixed-configuration
WS-C2960G-24TC-L
● LAN Base image
● 44 Ethernet 10/100/1000 ports and 4 dual-purpose uplinks (each dual-purpose uplink port has 1
10/100/1000 Ethernet port and 1 SFP-based Gigabit Ethernet port, 1 port active)
● 1 RU fixed-configuration
WS-C2960G-48TC-L
● LAN Base image
Table 15.
Ordering Information for Cisco Catalyst 2960-S and 2960 Series Switches with LAN Base Software Accessories
Part Numbers
Description
CAB-STK-E-0.5M=
FlexStack stacking cable with a 0.5 m length
CAB-STK-E-1M=
FlexStack stacking cable with a 1.0 m length
CAB-STK-E-3M=
FlexStack stacking cable with a 3.0 m length
CAB-CONSOLE-RJ45
Console cable 6 ft with RJ45
CAB-CONSOLE-USB
Console cable 6 ft with USB Type A and mini-B connectors
CAB-16AWG-AC
AC power cord, 16AWG
CAB-ACE
AC power cord (Europe), C13, CEE 7, 1.5M
CAB-L620P-C13-US
Power cord, 250VAC, 15A, NEMA L6-20 to C13, US
CAB-ACI
AC power cord (Italy), C13, CEI 23-16, 2.5m
CAB-ACU
AC power cord (UK), C13, BS 1363, 2.5m
CAB-ACA
AC power cord (China/Australia), C13, AS 3112, 2.5m
CAB-ACS
AC power cord (Switzerland), C13, IEC 60884-1, 2.5m
CAB-ACR
AC power cord (Argentina), C13, EL 219 (IRAM 2073), 2.5m
CAB-ACC
Power cord (China) 10A, IEC 320, C13 (APN=CS-PWR-CH)
CAB-JPN-12A
CABASY,POWER CORD, JAPAN 2P, PSE, 12A @125VAC
CAB-L620P-C13-JPN
Power cord (Japan) 250VAC, 15A, NEMA L6-20 to C13, JAPAN
CAB-IND
Power cord (India)
PWR-RPS2300
Cisco Redundant Power System 2300 and blower, no power supply
BLNK-RPS2300=
Spare bay insert for Cisco Redundant Power System 2300 for Cisco Catalyst 2960 and Cisco Catalyst 2960-S switches
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 25 of 26
Data Sheet
Part Numbers
Description
CAB-RPS2300-E=
Spare RPS2300 cable for Cisco Catalyst 2960-48PST-L, 2960-24PC-L and 2960-24LT-L switches and Cisco Catalyst
2960-S switches
CAB-RPS2300=
Spare RPS2300 cable for Cisco Catalyst 2960 except as noted with CAB-RPS2300-E above
BLWR-RPS2300=
Spare 45 CFM blower for Cisco Redundant Power System 2300
C3K-PWR-750WAC=
Cisco Catalyst 2960 and Cisco Catalyst 2960-S RPS 2300 750W AC power supply spare
PWR-A=
Power adapter for Cisco Catalyst 2960PD-8TT-L compact switch
CBLGRD-C2960-8TC=
Cable guard for Cisco Catalyst 2960-8TC compact switch
CBLGRD-C2960G-8TC=
Cable guard for Cisco Catalyst 2960G-8TC compact switch
RCKMNT-19-CMPCT=
Rack mount for Cisco Catalyst 2960-8TC and Cisco Catalyst 2960G-8TC compact switches
RCKMNT-1RU=
Spare rack-mount kit for Cisco Catalyst 2960 and 2960-S Series for 19- and 24-inch racks
RCKMNT-REC-1RU=
1 RU recessed rack-mount kit for Cisco Catalyst 2960 and 2960-S Series
GLC-LH-SM=
1000BASE-LX/LH SFP transceiver module for MMF and SMF, 1300-nm wavelength
GLC-SX-MM=
1000BASE-SX SFP transceiver module for MMF, 850-nm wavelength
GLC-ZX-SM=
1000BASE-ZX SFP transceiver module for SMF, 1550-nm wavelength
GLC-T=
1000BASE-T SFP transceiver module for Category 5 copper wire
Not supported on the Cisco Catalyst 2960-8TC and Cisco Catalyst 2960G-8TC compact switches or 2960-S with SFP+
GLC-BX-D=
1000BASE-BX10 SFP transceiver module for single strand SMF, 1490-nm TX/1310-nm RX wavelength
GLC-BX-U=
1000BASE-BX10 SFP transceiver module for single strand SMF, 1310-nm TX/1490-nm RX wavelength
GLC-GE-100FX=
100BASE-FX SFP module for Gigabit Ethernet ports, 1310-nm wavelength, 2 km over MMF
Not supported on the Cisco Catalyst 2960-8TC and Cisco Catalyst 2960G-8TC compact switches
GLC-FE-100FX=
100BASE-FX SFP module for 100-Mb ports, 1310-nm wavelength, 2 km over MMF
GLC-FE-100LX=
100BASE-LX10 SFP module for 100-Mb ports, 1310-nm wavelength, 10 km over SMF
GLC-FE-100BX-D=
100BASE-BX10-D SFP module for 100-Mb ports, 1550-nm TX/1310-nm RX wavelength, 10 km over single-strand SMF
GLC-FE-100BX-U=
100BASE-BX10-U SFP module for 100-Mb ports, 1310-nm TX/1550-nm RX wavelength, 10 km over single-strand SMF
CWDM-SFP-1470=
Cisco CWDM SFP 1470 nm; Gigabit Ethernet and 1G/2G Fibre Channel (FC) (gray)
CWDM-SFP-1490=
Cisco CWDM SFP, 1490 nm; Gigabit Ethernet and 1G/2G FC (violet)
CWDM-SFP-1510=
Cisco CWDM SFP, 1510 nm; Gigabit Ethernet and 1G/2G FC (blue)
CWDM-SFP-1530=
Cisco CWDM SFP, 1530 nm; Gigabit Ethernet and 1G/2G FC (green)
CWDM-SFP-1550=
Cisco CWDM SFP, 1550 nm; Gigabit Ethernet and 1G/2G FC (yellow)
CWDM-SFP-1570=
Cisco CWDM SFP, 1570 nm; Gigabit Ethernet and 1G/2G FC (orange)
CWDM-SFP-1590=
Cisco CWDM SFP, 1590 nm; Gigabit Ethernet and 1G/2G FC (red)
CWDM-SFP-1610=
Cisco CWDM SFP, 1610 nm; Gigabit Ethernet and 1G/2G FC (brown)
CAB-SM-LCSC-1M
1m fiber single-mode LC-to-SC connectors
CAB-SM-LCSC-5M
5m fiber single-mode LC-to-SC connectors
SFP-10G-LR=
10GBASE-LR SFP+ module
SFP-10G-SR=
10GBASE-SR SFP+ module
SFP-10G-LRM=
10GBASE-LRM SFP+ module
SFP-H10GB-CU1M=
10GBASE-CU SFP+ Cable 1 Meter
SFP-H10GB-CU3M=
10GBASE-CU SFP+ Cable 3 Meter
SFP-H10GB-CU5M=
10GBASE-CU SFP+ Cable 5 Meter
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 26 of 26
Data Sheet
For more information about Cisco products, contact:
●
United States and Canada: (toll free) 800 553-NETS (6387)
●
Europe: 32 2 778 4242
●
Australia: 612 9935 4107
●
Other: 408 526-7209
●
World Wide Web URL: http://www.cisco.com
Printed in USA
© 2010 - 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-341562-11
01/11
Page 27 of 26
ITEM 6
Data Sheet
Cisco Aironet 1140 Series Access Point
Performance with Investment Protection
● Six times faster than 802.11a/g networks
● Backward-compatible with 802.11a/b/g
clients
● M-Drive technology optimizes RF
Taking Business Mobility Mainstream
®
®
The Cisco Aironet 1140 Series Access Point is a business-ready,
802.11n access point designed for simple deployment and energy
efficiency. The high-performance platform, which offers at least six times
the throughput of existing 802.11a/g networks, prepares the business for
the next wave of mobile devices and applications. Building on the Cisco
Aironet heritage of RF excellence, the 1140 Series combines the
industry’s most widely deployed 802.11n technology with a sleek
industrial design that blends seamlessly into any enterprise environment.
Designed for sustainability, the 1140 Series delivers high performance
from standard 802.3af Power over Ethernet while decreasing waste with
multiunit eco-packs and Energy Star certified power supplies. As part of
the Cisco Unified Wireless Network, the 1140 Series provides the
industry’s lowest total cost of ownership and investment protection by
integrating seamlessly with the existing network.
RF Excellence
The Cisco Unified Wireless Network with M-Drive technology removes the
mystery associated with design, implementation, and ongoing
optimization of enterprise wireless networks. With Cisco M-Drive
technology, IT has the tools needed to build and operate a high
Easy Installation and Power Efficient
● 802.11n performance with existing PoE
switches
● Sleek design blends into a variety of indoor
environments
Secure Interoperability
● 802.11n compliant
● Intel Connect with Centrino Certified
Simplified Network Management
● Controller-based or standalone deployment
options
● CleanAir1 technology reduces
troubleshooting and performance impacts
Secure Connections
● Supports rogue access point detection and
denial of service attacks
● Management frame protection detects
malicious users and alerts network
administrators
Greater Network Capacity
● Dynamic frequency selection 2 (DFS-2)
compliant
Easy-to-Install, Multipurpose Mounting
Bracket
● Designed for easy replacement of existing
access points
● UL 2043 plenum rated for above ceiling
installation options or suspended from drop
ceilings.
● Locks for theft protection
performance wireless network without the need for extensive RF
engineering skills. Cisco M-Drive technology is a systemwide approach
that manages the corporate RF spectrum, improves wireless coverage,
and increases system capacity and performance. Features include:
●
Radio resource management (RRM): Automated self-healing optimizes the unpredictability of RF to reduce
dead spots and help ensure high availability client connections. RRM optimizes network capacity and
mitigates interference by continuously monitoring and adjusting access point power and channel settings and
then load balancing clients to enhance wireless coverage.
© 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 1 of 6
Data Sheet
●
1
CleanAir technology: Only Cisco offers a comprehensive solution to detect, classify, locate, and mitigate
sources of interference, including non-Wi-Fi sources such as Bluetooth, microwave ovens, cordless phones,
and more. With the ability to visualize performance-impacting interference directly from Wireless Control
System (WCS), you can proactively manage the challenges of a shared wireless spectrum and optimize
network performance.
Environmentally Responsible
The Cisco Aironet 1140 Series offers 802.11n performance with standard 802.3af Power over Ethernet (PoE). At
only 12.95 watts of power, the 1140 Series is the only platform to combine the power of dual-radio 802.11n with the
efficiency of standard PoE. Additionally, the 1140 Series is designed to operate more efficiently during off-peak
hours when fewer clients are connected to the access point.
For quicker staging and installation, you can order the 1140 Series in multiunit eco-packs, which offer 10 Unified or 5
Standalone access points in a single, easy-to-open carton. Eco-packs reduce product packaging by 50 percent,
preserving natural resources and reducing emissions. By eliminating unnecessary components and offering digital
instead of paper documentation, the 1140 Series eco-packs will save over 2200 trees per year, which is equal to the
amount of power required to heat over 65 homes for an entire year.
Product Specifications
Table 1 lists the product specifications for Cisco Aironet 1140 Series Access Points.
Table 1.
Product Specifications for Cisco Aironet 1140 Series Access Points
Item
Specification
Part Numbers
Cisco Aironet 1140 Series Access Point
● AIR-LAP1142N-x-K9—Dual-band Controller-based 802.11a/g/n
● AIR-LAP1141N-x-K9—Single-band Controller-based 802.11g/n
● AIR-AP1142N-x-K9—Dual-band Standalone 802.11a/g/n
● AIR-AP1141N-x-K9—Single-band Standalone 802.11g/n
● AIR-LAP1142-xK9-PR—Eco-pack (dual-band 802.11a/g/n) 10 quantity Controller-based access points
● AIR-AP1142-xK9-5PR—Eco-pack (dual-band 802.11a/g/n) 5 quantity Standalone access points
Regulatory domains: (x = regulatory domain)
Customers are responsible for verifying approval for use in their individual countries. To verify approval and to identify
the regulatory domain that corresponds to a particular country, please visit
http://www.cisco.com/go/aironet/compliance.
Not all regulatory domains have been approved. As they are approved, the part numbers will be available on the
Global Price List.
Software
● Cisco Unified Wireless Network Software Release 6.0 or later.
● Cisco IOS® Software Release 12.4(21a)JA
Draft 802.11n Version 2.0
(and Related) Capabilities
● 2x3 multiple-input multiple-output (MIMO) with two spatial streams
● Maximal ratio combining (MRC)
● Legacy beamforming (hardware supports this capability; not yet enabled in software)
● 20- and 40-MHz channels
● PHY data rates up to 300 Mbps
● Packet aggregation: A-MPDU (Tx/Rx), A-MSDU (Tx/Rx)
● 802.11 dynamic frequency selection (DFS) (Bin 5)
● Cyclic shift diversity (CSD) support
Data Rates Supported
802.11a: 6, 9, 12, 18, 24, 36, 48, and 54 Mbps
802.11g: 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 Mbps
802.11n data rates (2.4 GHz and 5 GHz):
2
MCS Index
3
GI = 800ns
GI = 400ns
1
Requires Cisco Wireless Control System and Cisco Spectrum Expert Wi-Fi
MCS Index: The Modulation and Coding Scheme (MCS) index determines the number of spatial streams, the modulation, the
coding rate, and data rate values.
2
© 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 2 of 6
Data Sheet
Item
Frequency Band and 20MHz Operating Channels
Specification
20-MHz Rate (Mbps)
40-MHz Rate (Mbps)
20-MHz Rate (Mbps)
40-MHz Rate (Mbps)
0
6.5
13.5
7.2
15
1
13
27
14.4
30
2
19.5
40.5
21.7
45
3
26
54
28.9
60
4
39
81
43.3
90
5
52
108
57.8
120
6
58.5
121.5
65
135
7
65
135
72.2
150
8
13
27
14.4
30
9
26
54
28.9
60
10
39
81
43.3
90
11
52
108
57.8
120
12
78
162
86.7
180
13
104
216
115.6
240
14
117
243
130
270
15
130
270
144.4
300
A (Americas (FCC)):
● 2.412 to 2.462 GHz; 11 channels
N (Non-FCC):
● 2.412 to 2.462 GHz; 11 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.500 to 5.700 GHz, 8 channels
(excludes 5.600 to 5.640 GHz)
● 5.745 to 5.825 GHz; 5 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.745 to 5.825 GHz; 5 channels
C (China):
● 2.412 to 2.472 GHz; 13 channels
P (Japan2):
● 2.412 to 2.472 GHz; 13 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.745 to 5.825 GHz; 5 channels
S (Singapore):
● 2.412 to 2.472 GHz; 13 channels
E (ETSI):
● 2.412 to 2.472 GHz; 13 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.745 to 5.825 GHz; 5 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.500 to 5.700 GHz, 11 channels
T (Taiwan):
● 2.412 to 2.462 GHz; 11 channels
I (Middle East):
● 2.412 to 2.472 GHz, 13 channels
● 5.280 to 5.320 GHz; 3 channels
● 5.500 to 5.700 GHz, 11 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.745 to 5.825 GHz; 5 channels
K (Korea):
● 2.412 to 2.472 GHz; 13 channels
● 5.180 to 5.320 GHz; 8 channels
● 5.500 to 5.620 GHz, 7 channels
● 5.745 to 5.805 GHz, 4 channels
Note: This varies by regulatory domain. Refer to the product documentation for specific details for each regulatory domain.
Maximum Number of NonOverlapping Channels
2.4 GHz
● 802.11b/g:
◦ 20 MHz: 3
● 802.11n:
5 GHz
● 802.11a:
◦ 20 MHz: 21
● 802.11n:
◦
20 MHz: 3
◦
20 MHz: 21
◦
40 MHz: 1
◦
40 MHz: 9
Note: This varies by regulatory domain. Refer to the product documentation for specific details for each regulatory domain.
3
GI: A Guard Interval (GI) between symbols helps receivers overcome the effects of multipath delays.
© 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 3 of 6
Data Sheet
Item
Receive Sensitivity
Maximum Transmit Power
Specification
802.11b
802.11g
802.11a
-91 dBm @ 1 Mb/s
-86 dBm @ 6 Mb/s
-90 dBm @ 6 Mb/s
-91 dBm @ 2 Mb/s
-86 dBm @ 9 Mb/s
-90 dBm @ 9 Mb/s
-91 dBm @ 5.5 Mb/s
-86 dBm @ 12 Mb/s
-90 dBm @ 12 Mb/s
-88 dBm @ 11 Mb/s
-86 dBm @ 18 Mb/s
-90 dBm @ 18 Mb/s
-85 dBm @ 24 Mb/s
-88 dBm @ 24 Mb/s
-83 dBm @ 36 Mb/s
-85 dBm @ 36 Mb/s
-78 dBm @ 48 Mb/s
-80 dBm @ 48 Mb/s
-77 dBm @ 54 Mb/s
-79 dBm @ 54 Mb/s
2.4-GHz
2.4-GHz
5-GHz
802.11n (HT20)
802.11n (HT40)
802.11n (HT20)
802.11n (HT40)
-88 dBm @ MCS0
-85 dBm @ MCS0
-91 dBm @ MCS0
-78 dBm @ MCS0
-87 dBm @ MCS1
-85 dBm @ MCS1
-91 dBm @ MCS1
-78 dBm @ MCS1
-86 dBm @ MCS2
-83 dBm @ MCS2
-90 dBm @ MCS2
-78 dBm @ MCS2
-83 dBm @ MCS3
-80 dBm @ MCS3
-87 dBm @ MCS3
-78 dBm @ MCS3
-80 dBm @ MCS4
-77 dBm @ MCS4
-84 dBm @ MCS4
-78 dBm @ MCS4
-76 dBm @ MCS5
-72 dBm @ MCS5
-79 dBm @ MCS5
-75 dBm @ MCS5
-74 dBm @ MCS6
-71 dBm @ MCS6
-77 dBm @ MCS6
-73 dBm @ MCS6
-73 dBm @ MCS7
-70 dBm @ MCS7
-76 dBm @ MCS7
-72 dBm @ MCS7
-87 dBm @ MCS8
-85 dBm @ MCS8
-90 dBm @ MCS8
-76 dBm @ MCS8
-85 dBm @ MCS9
-82 dBm @ MCS9
-89 dBm @ MCS9
-76 dBm @ MCS9
-83 dBm @ MCS10
-80 dBm @ MCS10
-86 dBm @ MCS10
-76 dBm @ MCS10
-80 dBm @ MCS11
-76 dBm @ MCS11
-83 dBm @ MCS11
-76 dBm @ MCS11
-77 dBm @ MCS12
-73 dBm @ MCS12
-80 dBm @ MCS12
-76 dBm @ MCS12
-73 dBm @ MCS13
-69 dBm @ MCS13
-75 dBm @ MCS13
-71 dBm @ MCS13
-71 dBm @ MCS14
-67 dBm @ MCS14
-74 dBm @ MCS14
-69 dBm @ MCS14
-70 dBm @ MCS15
-66 dBm @ MCS15
-72 dBm @ MCS15
-68 dBm @ MCS15
2.4GHz
● 802.11b
5-GHz
5GHz
● 802.11a
◦ 20 dBm with 1 antenna
● 802.11g
◦ 17 dBm with 1 antenna
● 802.11n non-HT duplicate (802.11a duplicate) mode
◦ 17 dBm with 1 antenna
● 802.11n (HT20)
◦ 17 dBm with 1 antenna
● 802.11n (HT20)
◦ 20 dBm with 2 antennas
● 802.11n (HT40)
◦ 20 dBm with 2 antennas
● 802.11n (HT40)
◦
◦
20 dBm with 2 antennas
20 dBm with 2 antennas
Note: The maximum power setting will vary by channel and according to individual country regulations. Refer to the product documentation for specific
details.
Available Transmit Power
Settings
2.4GHz
5GHz
20 dBm (100 mW)
20 dBm (100 mW)
17 dBm (50 mW)
17 dBm (50 mW)
14 dBm (25 mW)
14 dBm (25 mW)
11 dBm (12.5 mW)
11 dBm (12.5 mW)
8 dBm (6.25 mW)
8 dBm (6.25 mW)
5 dBm (3.13 mW)
5 dBm (3.13 mW)
2 dBm (1.56 mW)
2 dBm (1.56 mW)
–1 dBm (0.78 mW)
–1 dBm (0.78 mW)
Note: The maximum power setting will vary by channel and according to individual country regulations. Refer to the product documentation for specific
details.
Integrated Antenna
● 2.4 GHz, Gain 4.0 dBi, horizontal beamwidth 360°
● 5 GHz, Gain 3 dBi, horizontal beamwidth 360°
Interfaces
● 10/100/1000BASE-T autosensing (RJ-45)
● Management console port (RJ45)
Indicators
● Status LED indicates boot loader status, association status, operating status, boot loader warnings, boot loader
errors.
Dimensions
● Access point (without mounting bracket): 8.7 x 8.7 x 1.84 in. (22.1 x 22.1 x 4.7 cm)
(W x L x H)
© 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 4 of 6
Data Sheet
Item
Specification
Weight
● 2.3 lbs (1.04 kg)
Environmental
● Nonoperating (storage) temperature: –22 to 185°F (–30 to 85°C)
● Operating temperature: 32 to104°F (0 to 40°C)
● Operating humidity: 10 to 90% percent (non-condensing)
System Memory
● 128 MB DRAM
● 32 MB flash
Input Power Requirements
● AP1140: 44 to 57 VDC
● Power Supply and Power Injector: 100 to 240 VAC; 50 to 60 Hz
Powering Options
● 802.3af Ethernet Switch
● Cisco AP1140 Power Injectors (AIR-PWRINJ4=)
● Cisco AP1140 Local Power Supply (AIR-PWR-A=)
Power Draw
● AP1140: 12.95 W
Note: When deployed using PoE, the power drawn from the power sourcing equipment will be higher by some amount
dependent on the length of the interconnecting cable. This additional power may be as high as 2.45W, bringing the
total system power draw (access point + cabling) to 15.4W.
Warranty
90 days
Compliance
Standards
● Safety:
◦
UL 60950-1
◦
CAN/CSA-C22.2 No. 60950-1
◦
UL 2043
◦
IEC 60950-1
◦
EN 60950-1
● Radio approvals:
◦
FCC Part 15.247, 15.407
◦
RSS-210 (Canada)
◦
EN 300.328, EN 301.893 (Europe)
◦
ARIB-STD 33 (Japan)
◦
ARIB-STD 66 (Japan)
◦
ARIB-STD T71 (Japan)
◦
AS/NZS 4268.2003 (Australia and New Zealand)
◦
EMI and susceptibility (Class B)
◦
FCC Part 15.107 and 15.109
◦
ICES-003 (Canada)
◦
VCCI (Japan)
◦
EN 301.489-1 and -17 (Europe)
◦
EN 60601-1-2 EMC requirements for the Medical Directive 93/42/EEC
● IEEE Standard:
◦ IEEE 802.11a/b/g, IEEE 802.11n, IEEE 802.11h, IEEE 802.11d
● Security:
◦
802.11i, Wi-Fi Protected Access 2 (WPA2), WPA
◦
802.1X
◦
Advanced Encryption Standards (AES), Temporal Key Integrity Protocol (TKIP)
● EAP Type(s):
◦
Extensible Authentication Protocol-Transport Layer Security (EAP-TLS)
◦
EAP-Tunneled TLS (TTLS) or Microsoft Challenge Handshake Authentication Protocol Version 2 (MSCHAPv2)
◦
Protected EAP (PEAP) v0 or EAP-MSCHAPv2
◦
Extensible Authentication Protocol-Flexible Authentication via Secure Tunneling (EAP-FAST)
◦
PEAPv1 or EAP-Generic Token Card (GTC)
◦
EAP-Subscriber Identity Module (SIM)
● Multimedia:
◦ Wi-Fi Multimedia (WMM™)
● Other:
Calculated Mean Time
Between Failure (MTBF)
◦
FCC Bulletin OET-65C
◦
RSS-102
390,000 hours
© 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 5 of 6
Data Sheet
Service and Support
Cisco and Cisco Wireless LAN Specialized Partners offer a broad portfolio of end-to-end services based on proven
methodologies for planning, designing, implementing, operating, and optimizing the performance of your wireless
network.
Cisco recommends the following services for the Cisco Aironet 1140 Series Access Points implementation:
Cisco Wireless LAN 802.11n Readiness Assessment Service
Prevent common challenges and reduce deployment costs by determining the readiness of your wired and wireless
infrastructure.
Cisco Wireless LAN 802.11n Migration Service
Simplify the migration to high-performance, next generation 802.11n.
Cisco Wireless LAN Optimization Service
Evolve your 802.11n network to meet ever-changing network demands through planning and assessments, design,
performance tuning, and ongoing support for system changes.
For more information about Cisco 802.11n planning and deployment services, visit
http://www.cisco.com/go/wirelesslanservices.
For More Information
For more information about the Cisco Aironet 1140 Series, visit http://www.cisco.com/go/wireless or contact your
local account representative.
Printed in USA
© 2010 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
C78-502793-05
02/10
Page 6 of 6
ITEM 7
Data Sheet
Cisco 5500 Series Wireless Controllers
®
Maximum Performance and Scalability
● Support for up to 500 access points and 7000 clients.
● 802.11n optimized for up to nine times the
performance of 802.11a/g networks.
● Enhanced uptime with the ability to simultaneously
configure and manage 500 access points per
controller.
The Cisco 5500 Series Wireless Controller is a highly scalable
and flexible platform that enables system wide services for
mission-critical wireless in medium to large-sized enterprises
and campus environments. Designed for 802.11n performance
and maximum scalability, the 5500 Series offers enhanced
uptime with RF visibility and protection, the ability to
Improved Mobility and Services
● Larger mobility domain for more simultaneous client
associations.
● Faster RRM updates for uninterrupted network access
when roaming.
● Intelligent RF control plane for self-configuration, selfhealing, and self-optimization.
● Efficient roaming improves application performance
such as toll quality, voice, and consistent streaming
video and data backup.
simultaneously manage up to 500 access points; superior
Licensing Flexibility and Investment Protection
● Additional access point capacity licenses may be
added over time.
Series offers improved mobility and prepares the business for
OfficeExtend Solution
● Secure, simple, cost-effective mobile teleworker
solution.
● Up to 500 remote access points per controller.
● Supports Unified Communications wireless phones for
reduced cell phone charges.
Comprehensive Wired/Wireless Security
● Full CAPWAP access point to controller encryption.
● Supports rogue access point detection and denial-ofservice attacks.
● Management frame protection detects malicious users
and alerts network administrators.
Enterprise Wireless Mesh
● Dynamic wireless mesh networks support indoor and
outdoor connectivity for areas that are difficult to wire.
Environmentally Responsible
● Support for adaptive power management to turn off
access point radios during off-peak hours to reduce
power consumption.
● OfficeExtend solution reduces costs and supports
green best practices by reducing commuting time and
saving on gas, vehicle mileage, and insurance costs.
performance for reliable streaming video and toll quality voice;
and improved fault recovery for a consistent mobility
experience in the most demanding environments.
Features
Optimized for high performance wireless networking, the 5500
the next wave of mobile devices and applications. The 5500
Series supports a higher density of clients and delivers more
efficient roaming, with at least nine times the throughput of
existing 802.11a/g networks.
The 5500 Series automates wireless configuration and
management functions and allows network managers to have
the visibility and control needed to cost-effectively manage,
secure and optimize the performance of their wireless
networks. With integrated CleanAir technology the 5500 Series
protects 802.11n performance by providing cross-network
access to real-time and historic RF interference information for
quick, troubleshooting and resolution. As a component of the
Cisco Unified Wireless Network, this controller provides
®
realtime communication between Cisco Aironet access points,
the Cisco Wireless Control System (WCS), and the Cisco
Mobility Services Engine to deliver centralized security policies,
wireless intrusion prevention system (IPS) capabilities, awardwinning RF management, and quality of service (QoS).
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 8
Software Licensing Flexibility
Base access point licensing offers flexibility to add up to 500 additional access points as business needs grow. The
licensing structure supports a variety of business mobility needs as part of the basic feature set, including the
OfficeExtend solution for secure, mobile teleworking and Enterprise Wireless Mesh, which allows access points to
dynamically establish wireless connections in locations where it may be difficult or impossible to physically connect
to the wired network.
Table 1 lists the features of the Cisco 5500 Series Wireless LAN Controllers.
Table 1.
Cisco 5500 Series Wireless LAN Controller Features
Feature
Benefits
Scalability
● Supports 12, 25, 50,100, 250 or 500 access points for business-critical wireless services at locations of
all sizes.
High Performance
● Wire speed, non-blocking performance for 802.11n networks.
RF Management
● Provides both real-time and historical information about RF interference impacting network performance
across controllers, via system wide CleanAir integration.
OfficeExtend
● Supports corporate wireless service for mobile and remote workers with secure wired tunnels to the
®
Cisco Aironet 1130 or 1140 Series Access Points.
● Extends the corporate network to remote locations with minimal set up and maintenance requirements
(zerotouch deployment).
● Improves productivity and collaboration at remote site locations.
● Separate SSID tunnels allow both corporate and personal Internet access.
● Reduced CO2 emissions from decrease in commuting.
● Higher employee job satisfaction from ability to work at home.
● Improves business resiliency by providing continuous, secure connectivity in the event of disasters,
pandemics, or inclement weather.
Comprehensive End-to-End
Security
● Offers Control and Provisioning of Wireless Access Points (CAPWAP) compliant DTLS encryption to
ensure full-line-rate encryption between access points and controllers across remote WAN/LAN links.
Enterprise Wireless Mesh
● Allows access points to dynamically establish wireless connections without the need for a physical
connection to the wired network.
● Available on select Cisco Aironet access points, Enterprise Wireless Mesh is ideal for warehouses,
manufacturing floors, shopping centers and any other location where extending a wired connection may
prove difficult or aesthetically unappealing.
High Performance Video
● Integrates VideoStream technology as part of the Cisco Medianet freamework to optimize the delivery of
video applications across the WLAN.
End-to-end Voice
● Supports Unified Communications for improved collaboration through messaging, presence, and
conferencing.
● Supports all Cisco Unified Communications Wireless IP Phones for cost-effective, real-time voice
services.
High Availability
● An optional redundant power supply helps to ensure maximum availability.
Environmentally Responsible
● Organizations may choose to turn off access point radios to reduce power consumption during off peak
hours.
Table 2 lists the product specifications for Cisco 5500 Series Wireless Controllers.
Table 2.
Product Specifications for Cisco 5500 Series Wireless Controllers
Item
Specifications
Wireless
IEEE 802.11a, 802.11b, 802.11g, 802.11d, W MM/802.11e, 802.11h, 802.11n
Wired/Switching/Routing
IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX specification, 1000BASE-T. 1000BASE-SX, 1000-BASELH, IEEE 802.1Q Vtagging, and IEEE 802.1AX Link Aggregation.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 8
Item
Data Request For Comments
(RFC)
Specifications
● RFC 768 UDP
● RFC 791 IP
● RFC 2460 IPv6 (pass through Bridging mode only)
● RFC 792 ICMP
● RFC 793 TCP
● RFC 826 ARP
● RFC 1122 Requirements for Internet Hosts
● RFC 1519 CIDR
● RFC 1542 BOOTP
● RFC 2131 DHCP
● RFC 5415 CAPWAP Protocol Specification
● RFC 5416 CAPWAP Binding for 802.11
Security Standards
● WPA
● IEEE 802.11i (WPA2, RSN)
● RFC 1321 MD5 Message-Digest Algorithm
● RFC 1851 The ESP Triple DES Transform
● RFC 2104 HMAC: Keyed Hashing for Message Authentication
● RFC 2246 TLS Protocol Version 1.0
● RFC 2401 Security Architecture for the Internet Protocol
● RFC 2403 HMAC-MD5-96 within ESP and AH
● RFC 2404 HMAC-SHA-1-96 within ESP and AH
● RFC 2405 ESP DES-CBC Cipher Algorithm with Explicit IV
● RFC 2406 IPsec
● RFC 2407 Interpretation for ISAKMP
● RFC 2408 ISAKMP
● RFC 2409 IKE
● RFC 2451 ESP CBC-Mode Cipher Algorithms
● RFC 3280 Internet X.509 PKI Certificate and CRL Profile
● RFC 3602 The AES-CBC Cipher Algorithm and Its Use with IPsec
● RFC 3686 Using AES Counter Mode with IPsec ESP
● RFC 4347 Datagram Transport Layer Security
● RFC 4346 TLS Protocol Version 1.1
Encryption
● WEP and TKIP-MIC: RC4 40, 104 and 128 bits (both static and shared keys)
● AES: CBC, CCM, CCMP
● DES: DES-CBC, 3DES
● SSL and TLS: RC4 128-bit and RSA 1024- and 2048-bit
● DTLS: AES-CBC
● IPSec: DES-CBC, 3DES, AES-CBC
Authentication, Authorization,
and Accounting (AAA)
● IEEE 802.1X
● RFC 2548 Microsoft Vendor-Specific RADIUS Attributes
● RFC 2716 PPP EAP-TLS
● RFC 2865 RADIUS Authentication
● RFC 2866 RADIUS Accounting
● RFC 2867 RADIUS Tunnel Accounting
● RFC 2869 RADIUS Extensions
● RFC 3576 Dynamic Authorization Extensions to RADIUS
● RFC 3579 RADIUS Support for EAP
● RFC 3580 IEEE 802.1X RADIUS Guidelines
● RFC 3748 Extensible Authentication Protocol
● Web-based authentication
● TACACS support for management users
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 8
Item
Management
Specifications
● SNMP v1, v2c, v3
● RFC 854 Telnet
● RFC 1155 Management Information for TCP/IP-Based Internets
● RFC 1156 MIB
● RFC 1157 SNMP
● RFC 1213 SNMP MIB II
● RFC 1350 TFTP
● RFC 1643 Ethernet MIB
● RFC 2030 SNTP
● RFC 2616 HTTP
● RFC 2665 Ethernet-Like Interface types MIB
● RFC 2674 Definitions of Managed Objects for Bridges with Traffic Classes, Multicast Filtering, and
Virtual Extensions
● RFC 2819 RMON MIB
● RFC 2863 Interfaces Group MIB
● RFC 3164 Syslog
● RFC 3414 User-Based Security Model (USM) for SNMPv3
● RFC 3418 MIB for SNMP
● RFC 3636 Definitions of Managed Objects for IEEE 802.3 MAUs
● Cisco private MIBs
Management Interfaces
● Web-based: HTTP/HTTPS
● Command-line interface: Telnet, Secure Shell (SSH) Protocol, serial port
● Cisco Wireless Control System (WCS)
Interfaces and Indicators
● Uplink: 8 (5508) 1000BaseT, 1000Base-SX and 1000Base-LH transceiver slots
● Small Form-Factor Pluggable (SFP) options (only Cisco SFPs supported): GLC-T, GLC-SX-MM, GLCLH-SM
● LED indicators: link
● Service Port: 10/100/1000 Mbps Ethernet (RJ45).
● Service Port: 10/100/1000 Mbps Ethernet (RJ45) For High Availability for future use
● LED indicators: link,
● Utility Port: 10/100/1000 Mbps Ethernet (RJ45)
● LED indicators: link
● Expansion Slots: 1 (5508)
● Console Port: RS232 (DB-9 male/RJ-45 connector included), mini-USB
● Other Indicators: Sys, ACT, Power Supply 1, Power Supply 2
Physical and Environmental
● Dimensions (W xDxH): 17.30 x 21.20 x 1.75 in. (440 x 539 x 44.5 mm)
● Weight: 20 lbs (9.1 kg) with 2 power supplies
● Temperature: Operating temperature: 32 to 104°F (0 to 40°C); Storage temperature: -13 to 158°F (-25 to
70°C)
● Humidity: Operating humidity: 10 95%, noncondensing; Storage humidity: up to 95%
● Input power: 100 to 240 VAC; 50/60 Hz; 1.05 A at 110 VAC, 115 W Maximum; 0.523 A at 220 VAC, 115
W Maximum; Test Conditions: Redundant Power Supplies, 40C, Full Traffic.
● Heat Dissipation: 392 BTU/hour at 110/220 VAC Maximum
Regulatory Compliance
CE Mark
Safety:
● UL 60950-1:2003
● EN 60950:2000
● EMI and susceptibility (Class A):
● U.S.: FCC Part 15.107 and 15.109
● Canada: ICES-003
● Japan: VCCI
● Europe: EN 55022, EN 55024
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 8
Table 3 and Table 4 list the ordering and accessories information for Cisco 5500 Series Wireless Controllers.
Table 3.
Ordering Information for Cisco 5500 Series Wireless Controllers
Part Number
Product Name
SMARTnet 8x5xNBD
AIR-CT5508-12-K9
5500 Series Wireless Controller for up to 12 Cisco access points
CON-SNT-CT0812
AIR-CT5508-25-K9
5500 Series Wireless Controller for up to 25 Cisco access points
CON-SNT-CT0825
AIR-CT5508-50-K9
5500 Series Wireless Controller for up to 50 Cisco access points
CON-SNT-CT0850
AIR-CT5508-100-K9
5500 Series Wireless Controller for up to 100 Cisco access points
CON-SNT-CT08100
AIR-CT5508-250-K9
5500 Series Wireless Controller for up to 250 Cisco access points
CON-SNT-CT08250
AIR-CT5508-500-K9
5500 Series Wireless Controller for up to 500 Cisco access points
CON-SNT-CT08500
AIR-CT5508-500-2PK
2 Pack 5500 Series Wireless Controller for up to 500 Cisco access points
each (1000 access points total)
CON-SNT-AIRC552P
Table 4.
Accessories for Cisco 5500 Series Wireless Controllers
Part Number
Product Name
AIR-PWR-5500-AC=
5500 Series Wireless Controller Redundant AC Power Supply
AIR-FAN-5500=
5500 Series Wireless Controller Fan Tray
AIR-CT5500-RK-MNT
5500 Series Wireless Controller Spare mounting kit
Additive Capacity Upgrade Licenses
The following additive capacity upgrade licenses are available for the Cisco 5500 Series:
Table 5.
e-License
Table 6.
Paper
License
Ordering Information for Cisco 5500 Series Wireless Controllers Additive Capacity Licenses (e-delivery PAK’s)
Part Number
Product Description
SMARTnet 8x5xNBD
L-LIC-CT5508-UPG
Primary upgrade SKU: Pick any number or combination of the following
options under this SKU to upgrade one or many controllers under one
product authorization key
CON-SNT-LCTUPG
L-LIC-CT5508-25A
25 AP Adder License for the 5508 Controller (eDelivery)
CON-SNT-LCT25A
L-LIC-CT5508-50A
50 AP Adder License for the 5508 Controller (eDelivery)
CON-SNT-LCT50A
L-LIC-CT5508-100A
100 AP Adder License for the 5508 Controller (eDelivery)
CON-SNT-LCT100A
L-LIC-CT5508-250A
250 AP Adder License for the 5508 Controller (eDelivery)
CON-SNT-LCT250A
Ordering Information for Cisco 5500 Series Wireless Controllers Additive Capacity Licenses (Paper PAK’s)
Part Number
Product Description
SMARTnet 8x5xNBD
LIC-CT5508-UPG
Primary upgrade SKU: Pick any number or combination of the following
options under this SKU, to upgrade one or many controllers under one
product authorization key.
CON-SNT-LCTUPG
LIC-CT5508-25A
25 AP Adder License for the 5508 Controller
CON-SNT-LCT25A
LIC-CT5508-50A
50 AP Adder License for the 5508 Controller
CON-SNT-LCT50A
LIC-CT5508-100A
100 AP Adder License for the 5508 Controller
CON-SNT-LCT100A
LIC-CT5508-250A
250 AP Adder License for the 5508 Controller
CON-SNT-LCT250A
The additive capacity licenses allow for the increase in access point capacity supported by the controller upto a
maximum of 500 Access points. As an example, if a controller was initially ordered with the 250 access point
support, that capacity could be later increased to upto 500 access points by purchasing a 250 access point additive
capacity license (1x-LIC-CT5508-250A).
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 8
A certificate with a PAK is required to add additional access point capacity on the Cisco 5500 Series Wireless
Controller.
The certificate may be expedited via email. If a paper certificate is required for customs, it should be ordered to
ship via U.S. mail. Each additive capacity license and PAK must be registered prior to installation.
Ordering and installing the Cisco 5500 Series Wireless Controller additive capacity licenses is a three-step
process:
1.
Select the correct SKU for email or paper delivery.
2.
Register the PAK certificate. (See Registering PAK Certificate).
3.
Install the license on the Cisco 5508 Series Wireless Controller. (See Installing License).
Please review the Cisco Wireless LAN Controller Configuration Guide, Release 6.0, for detailed ordering,
registration and installation information for the 5500 Series additive capacity licenses.
Electronic delivery of the same PAK’s is available by ordering the e-License SKUs as listed in Table 4. If a paper
certificate is required, please use the SKUs listed in Table 5.
PAK Certificate Registration
Customers are required to register a PAK certificate for all upgrade licenses for the Cisco 5500 Series Wireless
Controllers. Customer email address and host name are required to register the PAK certificate at
http://www.cisco.com/go/license.
Installing License on Cisco WCS Server
Follow these steps to install a license file. If you need additional help, contact Cisco Technical Assistance Center
(TAC) at 800 553-2447 or tac@cisco.com.
1.
Install Cisco WCS software if not already completed.
2.
Save the license file (.lic) to a temporary directory on your hard drive. (You will receive an email from Cisco
with an attached license file).
3.
Open a supported version of the Internet Explorer browser.
4.
In the location or address field, enter the following URL, replacing IP address with the IP address or host name
of the Cisco WCS server: https: // <IP address>.
5.
Log in to the Cisco WCS server as system administrator. (Be aware that usernames and passwords are
casesensitive.).
6.
From the Help menu select Licensing.
7.
On the Licensing page, from the command menu select Add License
8.
On the Add License page, click Browse to navigate to the location where you saved the .lic file.
9.
Click Download. The Cisco WCS server imports the license.
Table 7 shows the optional paper PAK license for Cisco 5500 Series Wireless Controllers. DTLS license is
designated for customers who purchase a controller with DTLS disabled due to import restrictions but get
permission to add DTLS support after initial purchase. This optional DTLS license is required for OfficeExtend
deployment.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 8
Table 7.
Optional Licensing for Cisco 5500 Series Wireless Controllers (Paper PAKs)
Part Number
Description
LIC-CT5508-LPE-K9
Cisco 5508 Controller DTLS License (Paper Certificate - US Mail)
Service and Support
Cisco Wireless LAN Services
Cisco and our specialized partners offer a broad portfolio of end-to-end services to help you improve your
organization’s productivity and collaboration by assisting with the readiness, deployment and optimization of your
wireless network and mobility services. Our services help you successfully deploy the 5500 Series Wireless
Controller and integrate mobility solutions effectively to lower the total cost of ownership and secure your wireless
network. To learn more about Cisco Wireless LAN Service offers, please visit
http://www.cisco.com/go/wirelesslanservices.
Cisco WLAN Advanced Services Consulting is available for the planning and deployment stages to help ensure the
successful integration of the Cisco 5500 Series Wireless Controller in your network. Cisco WLAN Advanced
Services Consulting can be ordered with the SKU listed in Table 6.
Please contact your Cisco Sales representative with the information required for a pricing quote:
●
Number of sites
●
Desired coverage area (square feet or square miles)
●
Estimated number of access points per site
●
Advanced Mobility Services and required applications
Table 8.
Ordering Information for planning and deployment consulting services for the Cisco 5500 Series Wireless
Controllers
Part Number
Service Name
AS-WLAN-CNSLT
Cisco WLAN Advanced Services Consulting
Summary
The Cisco 5500 Series Wireless Controller is designed for 802.11n performance and offers maximum scalability for
enterprise and service provider wireless deployments. It simplifies deployment and operation of wireless networks,
helping to ensure smooth performance, enhance security, and maximize network availability. The Cisco 5500
Series Wireless Controller manages all of the Cisco access points within campus environments and branch
locations, eliminating complexity and providing network administrators with visibility and control of their wireless
LANs.
For More Information
For more information about Cisco wireless controllers, contact your local account representative or visit
http://www.cisco.com/en/US/products/ps6366/index.html.
For more information about the Cisco Unified Wireless Network framework, visit
http://www.cisco.com/go/unifiedwireless.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 8
Printed in USA
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-521631-08
11/11
Page 8 of 8
ITEM 8a
www.dell.com/QRL/Server/PER320
Dell PowerEdge R320
An enterprise-class, 1-socket server, the Intel-powered Dell™ PowerEdge™ R320 has
the right computing power, scalability and value in a dense chassis.
The Dell PowerEdge R320 is an enterprise-class,
1-socket, 1U rack-mount server designed to deliver
the right combination of performance, redundancy
and value in a dense chassis. This rack server caters
to the growing need for virtualization by offering
scalable processor performance, a large memory
footprint and the capacity for up to eight hard drives.
The performance per cost, along with configuration
flexibility, storage connectivity and straightforward
systems management make the R320 highly
appealing to hosting providers. Consistent
worldwide support makes the R320 highly appealing
to multinational businesses and organizations.
Enterprise features, scalable
expandability and value in a
dense chassis
The R320 features the scalable performance of the
Intel® Xeon® E5-2400 processors with essential Intel
memory RAS features. This server complements its
processors with six DIMMs and two PCI Express®
(PCIe) slots, providing a substantial memory
footprint and wide I/O bandwidth to support both
memory-sensitive applications and databases. These
combined technology features enable the R320 to
support consolidated and virtualized environments.
To protect your virtualized workloads, the R320
offers dual SD cards making your hypervisors
redundant and failsafe. Other reliability and
availability features include up to four 3.5-inch or
eight 2.5-inch hot-plug hard drives, both hardware
and software RAID options and redundant, hot-plug
power supplies.
Ideal for your applications
The R320 is an excellent fit for web, file and
print serving as well as smaller scale hosting and
e-commerce, retail server, workgroup server and
smaller scale virtualization in space-constrained,
small-medium business locations and departmental
and remote sites of large businesses and public
organizations.
Enterprise-class network options
As a 1-socket rack server, the R320 has very
aggressive advanced network options, carrying
multiple third-party brands and adapter types with
10GbE NIC, 10GbE FCoE and Fiber Channel 8Gb
HBA.
The PowerEdge server line
The PowerEdge family is engineered with the right
combination of features and performance scalability
to handle tough workloads for both large and small
data center environments.
The Dell OpenManage™ systems management
portfolio includes integrated Dell Remote Access
Controller (iDRAC) with Lifecycle Controller. This
embedded feature helps IT administrators manage
Dell servers in physical, virtual, local and remote
environments, operating in-band or out-of-band,
with or without a systems management software
agent. OpenManage integrates and connects to
third-party systems management solutions so
you can maintain your single point of control and
capitalize on your existing investment. OpenManage
simplifies the lifecycle of deploying, updating,
monitoring, and maintaining your Dell PowerEdge
servers.
PowerEdge R320
• Enterprise computing with
Intel Xeon processors E5-2400
• Up to eight 2.5-inch drive
capacity
• Up to six DIMMs with RAS
• PCIe 3.0-enabled expansion
slots
• Enterprise redundancy and
scalable expandability
December 2012
Feature
PowerEdge R320 technical specification
Form factor
1U rack
Processors
Intel® Xeon® processor E5-2400 product family
Intel Xeon processor E5-1410
Intel Pentium® processor 1400 product family
Processor sockets
1
Internal interconnect
Intel DMI 2.0
Cache
2.5MB per core; core options: 2, 4, 6, 8
Chipset
Intel C600 series
Memory1
Up to 192GB (6 DIMM slots): 2GB/4GB/8GB/16GB/32GB DDR3 up to 1600MT/s
I/O slots
2 PCIe slots:
• One x8 PCIe slot with x4 bandwidth, 2.0, half-length, half-height
• One x16 PCIe slot with x16 bandwidth, 3.0, half-length, full-height
RAID controller
Internal controllers:
PERC S110 (SW RAID)
PERC H310
PERC H710
Drive bays
Up to eight 2.5” hot-plug SAS, SATA or SSD or four 3.5” SAS, SATA
Maximum internal storage1
Up to 16TB
Hard drives
Hot-plug hard drive options:
2.5” SATA, nearline SAS, SAS (15K, 10K), SAS SSD, SATA SSD
3.5” SATA, nearline SAS, SAS (15K)
Cabled hard drive options:
3.5” SATA, nearline SAS, SAS (15K)
Self-encrypting drives available
Embedded NIC
Broadcom® 5720 Dual Port 1Gb LOM
I/O adapter options
1Gb Ethernet:
Broadcom 5720 Dual Port 1Gb NIC
Broadcom 5720 Quad Port 1Gb NIC
Intel I350 Dual Port 1Gb stand-up adapter
Intel I350 Quad Port 1Gb stand-up adapter
10Gb Converged Ethernet:
Brocade® BR1020 Dual Port 10Gb CNA
QLogic® QLE8262 Dual Port 10Gb DA/SFP+
Broadcom 57810S Dual Port 10Gb Base-T CNA
Broadcom 57810S Dual Port 10Gb DA/SFP+ CNA
External HBAs (RAID):
PERC H810
External HBAs (non-RAID):
6Gbps SAS HBA
10Gb Ethernet:
Intel X520 Dual Port 10Gb DA/SFP+ server adapter
Intel X540 Dual Port 10Gb Base-T adapter
FC8/FC4 HBA:
QLogic QLE2460 4Gb Single Port FC HBA
QLogic QLE2462 4Gb Dual Port FC HBA
QLogic QLE2560 8Gb Single Port FC HBA
QLogic QLE2562 8Gb Dual Port FC HBA
Emulex® LPe-12000-E 8Gb Single Port FC HBA
Emulex LPe-12002-E 8Gb Dual Port FC HBA
Brocade 815 8Gb Single Port FC HBA
Brocade 825 8Gb Dual Port FC HBA
Power
Platinum efficiency, hot-plug, redundant 350W and 550W power supplies; Bronze efficiency, cabled 350W power supply
Auto-ranging power supplies
Availability
High-efficiency, hot-plug, redundant power supplies; hot-plug hard drives; TPM; dual internal SD support; fan fault
tolerance; optional bezel; information tag; ECC memory, interactive LCD screen; ENERGY STAR® compliant
Remote management
Basic management (default), iDRAC7 with Lifecycle Controller, iDRAC7 Express (upgrade option), iDRAC7 Enterprise
(upgrade option), 8GB or 16GB vFlash media (upgrade options)
Systems management
IPMI 2.0 compliant
Dell OpenManage™ Essentials and Dell Management Console
Dell OpenManage Power Center
Dell OpenManage Connections:
• OpenManage Integration Suite for Microsoft® System Center
• Dell plug-in for VMware® vCenter™
• HP Operations Manager, IBM Tivoli® Netcool®, and CA Network and Systems Management
Rack support
ReadyRailsTM II sliding rails for toolless mounting in 4-post racks with square or unthreaded round holes or tooled
mounting in 4-post threaded hole racks, with support for optional tool-less cable management arm
ReadyRails static rails for toolless mounting in 4-post racks with square or unthreaded round holes or tooled mounting
in 4-post threaded and 2-post (Telco) racks
Operating
systems
Microsoft® Windows Server® 2012
Microsoft Windows Server 2012 Essentials
Microsoft Windows Server 2008 R2 SP1, x64 (includes
Hyper-V® v2)
Novell® SUSE® Linux Enterprise Server
Red Hat® Enterprise Linux®
1
Virtualizations options:
Citrix® XenServer®
VMware® vSphere® ESX™ and ESXi™
Red Hat Enterprise Virtualization®
For more information on the specific versions and
additions, visit Dell.com/OSsupport.
GB means 1 billion bytes and TB equals 1 trillion bytes; actual capacity varies with preloaded material and operating environment and will be less.
OEM-ready version available
From bezel to BIOS to packaging, your servers can look and feel as if they were designed and built by you.
For more information, visit Dell.com/OEM.
Learn more at Dell.com/PowerEdge
© 2012 Dell Inc. All rights reserved. Dell, the DELL logo, the DELL badge, PowerEdge, and OpenManage are trademarks of Dell Inc. Intel and Xeon are
registered trademarks of Intel Corporation in the U.S. and other countries. Microsoft, Windows, Windows Server, and Hyper-V are either registered trademarks
or trademarks of Microsoft Corporation in the United States and/or other countries. Other trademarks and trade names may be used in this document to refer
to either the entities claiming the marks and names or their products. Dell disclaims proprietary interest in the marks and names of others. This document
is for informational purposes only. Dell reserves the right to make changes without further notice to any products herein. The content provided is as is and
without express or implied warranties of any kind.
ITEM 8b
.
Licensing and Ordering Guide
Cisco WCS Licensing and Ordering Guide
®
This Cisco Wireless Control System (WCS) licensing and ordering guide presents ordering guidelines
and licensing information for new and existing Cisco WCS deployments that are being upgraded to
support Cisco WCS Software Release 5.2 or later.
This guide includes information on buying new or expansion Cisco WCS licenses to deploy on single or
multiple servers (enterprise), adding new Cisco WCS enterprise licenses, converting from CiscoWorks
Wireless LAN Solution Engine (WLSE) to Cisco WCS, upgrading to the Cisco WCS Location and High
Availability option, and deploying the free Cisco WCS Demonstration License.
Overview
Cisco WCS is the industry-leading platform for wireless LAN planning, configuration, and management, and is the
management platform for the Cisco Unified Wireless Network. With Cisco WCS, network administrators have a
single solution for RF prediction, policy provisioning, network optimization, troubleshooting, reporting, asset tracking,
location-based services, security monitoring, and wireless LAN systems management.
®
Cisco WCS supports Cisco Aironet lightweight access points, Cisco wireless LAN controllers, and the Cisco 3300
Series Mobility Services Engine. Multiple Cisco WCS management platforms can be managed by Cisco WCS
Navigator. Refer to the WCS Navigator Licensing and Order Guide at
http://www.cisco.com/en/US/products/ps9742/products_data_sheets_list.html.
Cisco WCS licensing entitlement is applicable for new or expanded Cisco WCS deployments on single or multiple
servers (enterprise), CiscoWorks WLSE customers upgrading to Cisco WCS, Cisco WCS PLUS upgrades, and
existing Cisco WCS installations that are upgrading to Cisco WCS Software Release 5.2 or later. Cisco WCS
demonstration licenses are also available.
Note:
A complete listing of all Cisco WCS licenses is presented in Table 1.
Ordering and Installing Cisco WCS Licenses
Ordering and installing Cisco WCS licenses is a five-step process:
1.
Select the correct Cisco WCS SKU. (See Selecting Cisco WCS SKU and Figure 1 Cisco WCS Licensing
Structure)
2.
Order the Cisco WCS SKU. (See Ordering).
3.
Install Cisco WCS software after download. (See Installing Software).
4.
Register Product Authorization Key Certificate. (See Registering PAK Certificate).
5.
Install license file on Cisco WCS server(s). (See Installing License).
Note:
For Cisco demonstration license order and install steps, proceed to the Installing Cisco WCS
Demonstration License section.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 1 of 13
Licensing and Ordering Guide
Figure 1.
Cisco WCS Licensing Structure
Step 1: Selecting Cisco WCS SKU
Cisco WCS is available in either a Cisco WCS Base or Cisco WCS PLUS configuration.
Cisco WCS Base supports standard Cisco WCS capabilities.
Cisco WCS PLUS includes all WCS Base features plus the ability to track location of a single Wi-Fi device such as
a client, tag, or rogue access point on demand (limited location), N:1 High Availability (HA) for WCS servers, and
Cisco 3300 Series Mobility Services Engine (MSE) management which can expand location capabilities by adding
Cisco Context-Aware Software to simultaneously track up to 18,000 assets.
Note:
Customers who deploy HA for their WCS servers must have WCS 5.2 or later installed on their primary and
secondary servers. Additionally, customers must install a WCS STANDARD-K9 (PLUS configuration) or WCS-ENTPLUS-K9 license on each of the primary servers that are backed up by the secondary server. (Primary server
provides the license for the secondary server. No separate license is required for the secondary server).
Note:
Cisco WCS PLUS license products introduced in release 5.2 are backward compatible with existing Cisco
WCS Location and Enterprise licenses.
Customers can expand location capabilities beyond a single Wi-Fi device by adding a Cisco 3300 Series Mobility
Services Engine to simultaneously track up to 18000 Wi-Fi devices
Refer to the Cisco 3300 Series Mobility Services Engine Licensing and Ordering Guide
http://www.cisco.com/en/US/products/ps9742/products_data_sheets_list.html.
Cisco WCS is licensed as either a single server or enterprise deployment.
Single Server License Overview
●
Licenses: WCS-STANDARD-K9, WCS-PLUS-UPG-K9, and WCS-WLSE-UPG-K9
●
License increments: 50, 100, 500 (Up to 1500 for WLSE-to-WCS conversion only)
●
Single server deployment
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 2 of 13
Licensing and Ordering Guide
●
Suitable for customers deploying up to 500 (Up to 1500 for WLSE-to-WCS conversion) Cisco Aironet
lightweight access points
●
One license file per Product Authorization Key (PAK) certificate
●
Available in WCS Base and WCS PLUS configurations
Enterprise Server License (Multiple Servers) Overview (release 4.1 or later)
●
License: WCS-ENT-PLUS-K9
●
License increments: 1000, 2500, 10000, 50000
●
Single or multiple server deployment (Cisco WCS Navigator included in 10000, and 50000 licenses)
●
Suitable for customers deploying 500 or more Cisco Aironet lightweight access points
●
Multiple license files linked to a single PAK certificate
●
Server decrements available number of access points as licenses are allocated within the network
Ordering and Deployment Guidelines for Licenses
Please review the license ordering considerations listed below.
CISCO WCS BASE AND CISCO WCS PLUS LICENSES
●
Cisco WCS Base and Cisco WCS PLUS (single server and enterprise) licenses cannot be combined.
●
For single server deployments, it is more cost effective to purchase Cisco WCS PLUS initially rather than to
upgrade from a Cisco WCS Base to a Cisco WCS PLUS license at a later date.
●
All Cisco WCS licenses of the same option (Base or PLUS) are additive. Cisco WCS licenses can be
combined to support an incremental number of access points (such as 300, 700, 900) beyond the distinct
license increments (such as 50, 100, 500) offered.
Example 1: To purchase a new single server license for 800 access points
Purchase: WCS-STANDARD-K9, (1) WCS-APBASE-500, and (3) WCS-APBASE-100
Example 2: To purchase a new enterprise license for 20,000 access points:
Purchase: WCS-ENT-PLUS-K9, and (2) WCS-ENT-PLUS-10000
SINGLE SERVER AND ENTERPRISE LICENSES
●
Single server and Enterprise licenses can co-exist on a Cisco WCS server if the single server license is Cisco
WCS PLUS. If a Cisco WCS Base license was ordered initially, it must be upgraded to a Cisco WCS PLUS
license before the enterprise license can be added to the single server license.
Example: A customer has an existing Cisco WCS Base license for 500 access points (WCS-APBASE-500).
The customer wants to add an additional quantity of 800 access points on multiple Cisco WCS servers for a
total of 1300 access points.
Purchase: (1) WCS-PLUS-UPG-500 to upgrade the existing 500 Cisco WCS Base license to a Cisco WCS
PLUS license, and (1) WCS-ENT-1000 to support the new 800 access points.
●
Once allocated to a server, enterprise licenses cannot be broken down into smaller increments. For example,
if a license of 1000 is allocated in increments of 250 within the network, you cannot break down the 250
allocation further.
CISCO WCS SKUS
●
All Cisco WCS SKUs can be bought as a discrete SKU (first-time purchase) or as an expansion SKU (added
to an existing deployment) unless otherwise noted.
●
All Cisco WCS SKUs, except for the Cisco WCS Demonstration License, are orderable using the Cisco
Ordering Tool.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 3 of 13
Licensing and Ordering Guide
●
Each license is orderable in specified quantity blocks. To add multiple quantities of license blocks, you must
go back to the main screen and order additional family SKUs and then select the sub-SKU option and
quantity block required. Repeat this process until the correct quantity of licenses is ordered.
●
Cisco WCS licensing is not tied to the type of lightweight access point deployed since Cisco WCS licensing
does not distinguish among access point types. Each lightweight access point is counted as one access point
license.
Software SKUs
Review the six links below to identify your license requirements as either a NEW or EXISTING customer and to
identify the appropriate Cisco WCS Base or Cisco WCS PLUS SKU to order.
Click the link to go to that section.
Standalone Software Upgrade to Cisco WCS 5.2
Cisco WCS Base Options for NEW and EXISTING Customers (WCS-STANDARD-K9)
CISCO WLSE-to-Cisco WCS Base CONVERSION for EXISTING customers (WCS-WLSE-UPG-K9)
Cisco Base-to-Cisco PLUS Upgrade for EXISTING customers (WCS-PLUS-UPG-K9)
Cisco WCS PLUS Options for NEW Customers (WCS-STANDARD-K9, WCS-ENT-PLUS-K9)
Cisco WCS PLUS Options for EXISTING Customers (WCS-STANDARD-K9, WCS-ENT-PLUS-K9, WCS-WLSEUPG-K9)
View a complete listing of all Cisco WCS licenses in Table 1.
Standalone Software Upgrade to Cisco WCS 5.2 or Later
If you are an EXISTING Cisco WCS 5.1 customer who wants to upgrade to Cisco WCS 5.2 or later, have a valid
SAS/SAU, and are not ordering any licenses, proceed to
http://tools.cisco.com/support/downloads/go/Redirect.x?mdfid=279705270.
Log in required.
CISCO WCS BASE OPTIONS FOR NEW AND EXISTING CUSTOMERS (WCS-STANDARD-K9)
●
If you are a NEW Cisco WCS customer who wants support for 50, 100, or 500 access points in a single
server deployment, order WCS-STANDARD-K9 and select one of the Cisco Base options below:
WCS-APBASE-50: License supports up to 50 access points.
WCS-APBASE-100: License supports up to 100 access points.
WCS-APBASE-500: License supports up to 500 access points.
Note: If your access point deployment does not exactly match 50, 100 or 500, you need to order multiple
licenses. For example, to support an access point deployment of 250 you would order (2) WCS-APBASE-100
licenses + (1) WCS-APBASE-50 license. This ordering process applies to both new and upgrade orders.
●
If you are an EXISTING Cisco WCS customer who wants to increase access points support within a single
server deployment, order WCS-STANDARD-K9 and select one of the Cisco Base options below:
WCS-APBASE-50: License supports up to 50 access points.
WCS-APBASE-100: License supports up to 100 access points.
WCS-APBASE-500: License supports up to 500 access points.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 4 of 13
Licensing and Ordering Guide
Note: If your increased access point deployment does not exactly match 50, 100 or 500, you need to order
multiple licenses. For example, to support an access point deployment of 250 (and you already have a WCSBASE-100 license) you would order (1) WCS-APBASE-100 license + (1) WCS-APBASE-50 license.
Note: These are the same licenses ordered by new customers. Licenses are additive and ordered in
increments whether ordered for a new or existing deployment.
CISCO WLSE-TO-WCS BASE CONVERSION CUSTOMERS (WCS-WLSE-UPG-K9)
●
If you are a CiscoWorks WLSE (models 1130-19, 1133) customer who wants to convert to Cisco WCS
Base, and wants support for 50, 100, 500 or 1000 access points in a single server deployment, order WCSWLSE-UPG-K9 and select one of the Cisco Base options below:
WCS-WLSE-APB-50: License supports up to 50 access points.
WCS-WLSE-APB-100: License supports up to 100 access points.
WCS-WLSE-APB-500: License supports up to 500 access points.
WCS-WLSE-APB-1000: License supports up to 1000 access points.
Note: CiscoWorks WLSE Express model 1030, and CiscoWorks WLSE model 1105 are not supported by
this SKU. These WLSE models cannot be converted to Cisco WCS.
Note: WLSE licenses are tied to WLSE hardware and cannot be used on non-WLSE hardware.
CISCO BASE-TO-CISCO PLUS UPGRADE FOR EXISTING CUSTOMERS (WCS-PLUS-UPG-K9)
●
If you are an EXISTING customer who wants to upgrade from a Cisco Base to Cisco PLUS license,
order WCS-PLUS-UPG-K9 and select one of the Cisco WCS PLUS upgrade options below:
WCS-PLUS-UPG-50: License supports up to 50 access points.
WCS-PLUS-UPG-100: License supports up to 100 access points.
WCS-PLUS-UPG-500: License supports up to 500 access points.
Note: The number of WCS-PLUS-UPG-K9 licenses purchased must equal or exceed the number of installed
WCS Base licenses for the Cisco WCS to register as a Cisco WCS PLUS system. Thereafter, additional
capacity is added by ordering PLUS licenses.
CISCO WCS PLUS OPTIONS FOR NEW CUSTOMERS (WCS-STANDARD-K9, WCS-ENT-PLUS-K9)
●
If you are a NEW Cisco WCS customer with a single server deployment and want location tracking, high
availability, and support for 50, 100, or 500 access points, order WCS-STANDARD-K9 and select one of the
Cisco WCS PLUS options below:
WCS-PLUS-50: License supports up to 50 access points.
WCS-PLUS-100: License supports up to 100 access points.
WCS-PLUS-500: License supports up to 500 access points.
●
If you are a NEW Cisco WCS customer with an enterprise deployment and want single device Location
tracking, High Availability, and support for 1000, 2500, 10000, or 50000 access points, order WCS-ENTPLUS-K9 and one of the Cisco WCS PLUS options below:
WCS-ENT-PLUS-1000: License supports up to 1000 access points.
WCS-ENT-PLUS-2500: License supports up to 2500 access points.
WCS-ENT-PLUS-10000: License supports up to 10000 access points.
WCS-ENT-PLUS-50000: License supports up to 50000 access points.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 5 of 13
Licensing and Ordering Guide
CISCO WCS PLUS OPTIONS FOR EXISTING CUSTOMERS (WCS-STANDARD-K9, WCS-ENT-PLUS-K9, WCSWLSE-UPG-K9)
●
If you are an EXISTING Cisco WCS PLUS customer with a single server deployment and want to
increase the number of access points supported in your network, order WCS-STANDARD-K9 and one of the
Cisco WCS PLUS options below:
WCS-PLUS-50: License supports up to 50 access points.
WCS-PLUS-100: License supports up to 100 access points.
WCS-PLUS-500: License supports up to 500 access points.
Note: These are the same licenses ordered by new customers. Licenses are additive and ordered in
increments whether ordered for a new or existing deployment.
●
If you are an EXISTING Cisco WCS PLUS customer with an enterprise deployment who wants to
increase access points support within a multiple server deployment, order WCS-ENT-PLUS-K9 and select
one of the Cisco PLUS options below:
WCS-ENT-PLUS-1000: License supports up to 1000 access points.
WCS-ENT-PLUS-2500: License supports up to 2500 access points.
WCS-ENT-PLUS-10000: License supports up to 10000 access points.
WCS-ENT-PLUS-50000: License supports up to 50000 access points.
Note: These are the same licenses ordered by new customers. Licenses are additive and ordered in
increments whether ordered for a new or existing deployment.
●
If you are an EXISTING CiscoWorks WLSE (models 1130-19, 1133) customer and want to CONVERT to
Cisco WCS PLUS, and want support for 50, 100, 500 or up to master page1500 access points, order WCSWLSE-UPG-K9 and select one of the Cisco PLUS options below:
WCS-WLSE-PLUS-50: License supports up to 50 access points.
WCS-WLSE-PLUS-100: License supports up to 100 access points.
WCS-WLSE-PLUS-500: License supports up to 500 access points.
WCS-WLSE-PLUS-1000: License supports up to 1000 access points.
Note: CiscoWorks WLSE Express model 1030 and CiscoWorks WLSE model 1105 are not supported by this
SKU. These WLSE models cannot be converted to Cisco WCS.
Note: WLSE licenses are tied to WLSE hardware and cannot be used on non-WLSE hardware.
COMPLETE LISTING OF CISCO WCS LICENSES
Table 1 provides a complete listing of all Cisco WCS license SKUs.
Table 1.
Currently Available Cisco WCS Licenses
Product Part Number
Product Description
WCS-STANDARD-K9
New and Expanded Cisco WCS Deployments
Cisco WCS Base
● Supports deployment of Cisco WCS on a single server
WCS-APBASE-50
Cisco WCS Base license for 50 access points, Windows/Linux
WCS-APBASE-100
Cisco WCS Base license for 100 access points, Windows/Linux
WCS-APBASE-500
Cisco WCS Base license for 500 access points, Windows/Linux
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 6 of 13
Licensing and Ordering Guide
Product Part Number
Product Description
Cisco WCS Plus
● Supports deployment of Cisco WCS on a single server
● Supports mobility services enablement, high availability, and the ability to track the location of a single Wi-Fi device or tag on demand
● Backward-compatible with existing Cisco WCS location and enterprise licenses
WCS-PLUS-50
Cisco WCS Plus license for mobility services enablement and high availability for 50 access points, Windows/Linux
WCS-PLUS-100
Cisco WCS Plus license for mobility services enablement and high availability for 100 access points, Windows/Linux
WCS-PLUS-500
Cisco WCS Plus license for mobility services enablement and high availability for 500 access points, Windows/Linux
WCS-PLUS-UPG-K9
Upgrading Cisco WCS Base to Cisco WCS Plus
Cisco WCS Plus Upgrade
● Supports deployment of Cisco WCS on a single server
● Supports upgrading a Cisco WCS base license to support mobility services enablement, high availability, and location services for one device or
tag on demand
WCS-PLUS-UPG-50
Cisco WCS Plus Upgrade license with mobility services enablement and high availability supporting 50 access points,
Windows/Linux
WCS-PLUS-UPG-100
Cisco WCS Plus Upgrade license with mobility services enablement and high availability supporting 100 access
points, Windows/Linux
WCS-PLUS-UPG-500
Cisco WCS Plus Upgrade license with mobility services enablement and high availability supporting 500 access
points, Windows/Linux
WCS-ENT-PLUS-K9
Enterprise Plus Licenses for Large-Scale Deployments
Cisco Enterprise Plus Licenses
● Supports deployment of Cisco WCS on a single or multiple servers
● Supports mobility services enablement, high availability and the ability to track the location of a single Wi-Fi device or tag on demand
● Enterprises Plus licenses of 10,000 and 50,000 include a Cisco WCS Navigator (WCS-NAV-20) license
● These licenses are operational with Cisco Unified Wireless Network Software Release 4.1 and later.
WCS-ENT-PLUS-1000
Cisco WCS Enterprise Plus license with mobility services enablement and high availability for 1000 access points,
Windows/Linux on multiple Cisco WCS servers
WCS-ENT-PLUS-2500
Cisco WCS Enterprise Plus license with mobility services enablement and high availability for 2500 access points,
Windows/Linux on multiple Cisco WCS servers
WCS-ENT-PLUS-10000
Cisco WCS Enterprise Plus license with mobility services enablement and high availability for 10,000 access points,
Windows/Linux on multiple Cisco WCS servers. Includes WCS-NAV-20 license
WCS-ENT-PLUS-50000
Cisco WCS Enterprise Plus license with mobility services enablement and high availability for 50,000 access points,
Windows/Linux on multiple Cisco WCS servers. Includes WCS-NAV-20 license
WCS-WLSE-UPG-K9
Converting an existing CiscoWorks WLSE to Cisco WCS
CiscoWorks WLSE Conversion to Cisco WCS Base
● Supports deployment of Cisco WCS on a single server
● Available for CiscoWorks WLSE Models 1130-19 and 1133 only
WCS-WLSE-APB-50
Cisco WCS Base license for WLSE conversion supporting 50 access points, Linux
WCS-WLSE-APB-100
Cisco WCS Base license for WLSE conversion supporting 100 access points, Linux
WCS-WLSE-APB-500
Cisco WCS Base license for WLSE conversion supporting 500 access points, Linux
WCS-WLSE-APB-1000
Cisco WCS Base license for WLSE conversion supporting 1000 access points, Linux
CiscoWorks WLSE Conversion to Cisco WCS Plus
● Supports deployment of Cisco WCS on a single server
● Available for CiscoWorks WLSE Models 1130-19 and 1133 only
● Supports mobility services enablement, high availability, and the ability to track the location of a single Wi-Fi device or tag on demand
WCS-WLSE-PLUS-50
Cisco WCS Plus license with mobility services enablement and high availability for WLSE conversion supporting 50
access points, Linux
WCS-WLSE-PLUS-100
Cisco WCS Plus license with mobility services enablement and high availability for WLSE conversion supporting 100
access points, Linux
WCS-WLSE-PLUS-500
Cisco WCS Plus license with mobility services enablement and high availability for WLSE conversion supporting 500
access points, Linux
WCS-WLSE-PLUS-1000
Cisco WCS Plus license with mobility services enablement and high availability for WLSE conversion supporting 1000
access points, Linux
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 7 of 13
Licensing and Ordering Guide
Product Part Number
Product Description
AIR-WCS-DEMO-K9
Cisco WCS Demonstration License
● Step 1. Request the license from http://www.cisco.com/go/license.
● Step 2. Go to Cisco Wireless Software Center (login required) to download Cisco WCS software.
● Step 3. Install the Cisco WCS software on the customer-supplied server and enter the Cisco WCS demonstration license information
when prompted
● There is no Cisco Technical Assistance Center (TAC) support for the Cisco WCS demonstration license.
AIR-WCS-DEMO-K9
Free Cisco WCS full featured, location-enabled, 30 day demonstration license supporting 10 Cisco Aironet lightweight
access points
Step 2: Ordering
All purchasable Cisco WCS licenses can be ordered from the Cisco Ordering Tool.
To request help with ordering, please contact Cisco Customer Service http://www.cisco.com/go/customerservice.
PLEASE FOLLOW THE STEPS BELOW TO PLACE YOUR ORDER.
1.
Login to the Cisco Ordering Tool.
2.
Enter the family SKU: WCS-STANDARD-K9 or WCS-ENT-PLUS-K9 or WCS-PLUS-UPG-K9 or WCS-WLSEUPG-K9 into the Enter Product field. Press Enter. The Select Options window appears (Figure 2).
Figure 2.
Select Options Window
3.
Click Software License Option (left panel). The subordinate license options display (right panel).
4.
Click the circle next to license quantity (such as WCS-ENT-PLUS-2500) that you want to order.
5.
Click Check Configuration. A summary of your order appears (Figure 3).
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 8 of 13
Licensing and Ordering Guide
Figure 3.
6.
Check Configuration Window
Click Save to save the configuration.
Note: For the WCS-STANDARD-K9 and WCS-PLUS-UPG-K9 SKU families, customers are prompted to order
an optional CD (WCS-CD-K9) for a nominal charge during the ordering process. The WCS-CD-K9 contains one
software image of Cisco WCS software on a CD for Windows and Linux. This CD is shipped by U.S. mail to the
purchaser’s address. The optional CD is not available for WCS-WLSE-UPG-K9 because this SKU family
automatically ships in CD format.
Note: You can only order one license quantity at a time (such as WCS-ENT-PLUS-2500). If you need to order
multiple licenses to meet your access point support requirements, you must go back to the main screen and
reorder both the family SKU and subordinate SKU. Repeat this process as needed, until the correct quantity of
licenses is ordered.
7.
To return to the Main Screen to order additional license SKUs click New Configuration.
8.
Repeat steps 2 through 7 until you order your license quantity needs.
Step 3: Installing Software
You can download software during the ordering process.
PLEASE FOLLOW THESES STEPS TO DOWNLOAD AND INSTALL SOFTWARE
1.
Go to http://tools.cisco.com/support/downloads/go/Redirect.x?mdfid=279705270 and log in.
2.
Click on the appropriate link in the table (see Figure 4).
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 9 of 13
Licensing and Ordering Guide
Figure 4.
Select release from software download window
3.
Download software.
4.
Install the Cisco WCS software on your server(s).
PLEASE FOLLOW THESES STEPS TO INSTALL SOFTWARE FROM A CD
1.
If it is a WLSE-to-WCS conversion, do the conversion before installing Cisco WCS software.
2.
Install the Cisco WCS software on your server.
Step 4: Registering PAK Certificate
All purchased Cisco WCS SKUs require a PAK certificate to register the Cisco WCS license. All customers who
ordered new licenses and those upgrading from release 3.x will receive a PAK certificate either by US mail or
by email.
US mailed PAK: New or existing customers that are purchasing new Cisco WCS licenses from the Cisco Ordering
Tool will receive their PAK as a paper certificate through the US mail. Cisco sends the PAK upon purchase of the
Cisco WCS SKUs.
Emailed PAK: Existing Cisco WCS customers who are upgrading from Cisco WCS Software Release 3.x to Cisco
WCS software release 4.x or greater will receive their PAK certificate by email from the alias wcs-customerlicense@cisco.com.
PLEASE FOLLOW THESES STEPS TO REGISTER PAK CERTIFICATE
1.
Login and go to the licensing site at http://cisco.com/go/license.
2.
Follow the instructions on the web site to register the licenses using the PAK certificate.
Customer email address and host name are required to register.
Additionally, if it is a single server license, confirm SKU ordered (WCS Base or WCS PLUS); and if it is an
enterprise license, specify the number of access points to be decremented.
Note: For Cisco WCS demonstration licenses, PAK certificate registration is automatically completed during the
Cisco WCS demonstration license registration when the customer enters the host name of their server.
3.
Look for an email from licensing@cisco.com with the license file.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 10 of 13
Licensing and Ordering Guide
If you do not receive an email within an hour of registering your PAK, check your junk email folder. If you cannot
locate the email, please contact Cisco TAC at (800) 553-2447 or tac@cisco.com.
Step 5: Installing License on Cisco WCS Server
If you need help installing your license file please contact Cisco TAC at (800) 553-2447 or tac@cisco.com.
PLEASE FOLLOW THESE STEPS TO INSTALL LICENSE FILE
1.
Install Cisco WCS software if not already completed.
2.
Save the license file (.lic) to a temporary directory on your hard drive. (You will receive an email from Cisco with
an attached license file).
3.
Open a supported version of the Internet Explorer browser.
4.
In the location or address field, enter the following URL, replacing IP address with the IP address or host name
of the Cisco WCS server: https: // <IP address>.
5.
Log in to the Cisco WCS server as system administrator. (Be aware that usernames and passwords are casesensitive.).
6.
From the Help menu select Licensing.
7.
On the Licensing page, from the command menu select Add License....
8.
On the Add License page, click Browse to navigate to the location where you saved the .lic file.
9.
Click Download. The Cisco WCS server imports the license.
Installing Cisco WCS Demonstration License
You can experience Cisco WCS, the industry’s leading platform for wireless LAN planning, configuration,
management, and mobility services, for free for 30 days by downloading the new full-featured, location-enabled
Cisco WCS Demonstration License (WCS-DEMO-K9). The demonstration license is only available by download.
This license supports 10 access points for up to 30 days on a single server. Network configurations and set up for
the demonstration license are retained to make it easier to transition to a licensed Cisco WCS copy.
The Cisco WCS demonstration license 30 day period begins on the day the license is downloaded. Cisco TAC
support is not available for the Cisco WCS Demonstration License.
PLEASE FOLLOW THESE STEPS TO REQUEST AND INSTALL WCS DEMO CD
1.
Request Cisco WCS demonstration license at http://www.cisco.com/go/license or
https://tools.cisco.com/SWIFT/Licensing/PrivateRegistrationServlet.
2.
Go to the Licenses Not Requiring a PAK panel and click the here for available licenses link (Figure 5).
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 11 of 13
Licensing and Ordering Guide
Figure 5.
3.
Select Wireless Control System > Wireless Control System 30 day trial license (Figure 6).
Figure 6.
4.
Product License Registration for WCS Demo CD
Select 30 day trial license
Fill out the forms (registration, email) on the screens that follow.
Ensure that the correct host name of your target Cisco WCS server is entered.
You will receive an email titled Wireless Control System Field Demo License from licensing@cisco.com. This
email is sent to your registered email.
Note: The PAK registration is automatically completed during this registration process. You do not need to go
the PAK web site as you would for SKUs you purchase.
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
Page 12 of 13
Licensing and Ordering Guide
5.
Download Cisco WCS Software for Cisco WCS Demonstration License. Follow the steps in the section Step 3:
Installing Software to reach that download screen.
The email that is sent from Cisco licensing does not contain the Cisco WCS software image.
6.
Open the email received from licensing@cisco.com titled Wireless Control System Field Demo License.
Note: Cisco WCS software should be already installed on the server.
7.
Follow the instructions in the email to activate the Cisco WCS demonstration license.
Note: TAC support is not available for the demonstration license.
You can convert the demo license to a non-expiring license at anytime during the 30 day trial period. All WLAN
configuration information created in the original installation are retained during these upgrades. Customers
wishing to upgrade the demonstration license to non-expiring licenses with higher access point quantities may
do so by purchasing one of the Cisco WCS license SKUs from the Cisco Ordering Tool.
Printed in USA
© 2009 Cisco Systems, Inc. All rights reserved. This document is Cisco Public Information.
C07-508585-03
06/09
Page 13 of 13
ITEM 9
Data Sheet
Cisco 3300 Series Mobility Services Engine:
An Open, Appliance-Based Platform for Delivering
Mobility Services
Product Overview
®
The Cisco 3300 Series Mobility Services Engine (Figure 1) is an open platform that provides a new approach to
the delivery of mobility services in a centralized and scalable fashion. A combination of hardware and software,
the Cisco 3300 Series Mobility Services Engine (MSE) is an appliance-based solution that supports a suite of
software services. The Mobility Services Engine transforms the wireless LAN into a mobility network by abstracting
the application layer from the network layer, effectively allowing for the delivery of mobile applications across wired
and wireless networks.
Figure 1.
Cisco 3300 Series Mobility Services Engine
To deliver true business mobility, IT must take a practical approach focused on unifying networks, managing
the wave of mobile devices, and enabling mobile application development. The Cisco 3300 Series Mobility
Services Engine is at the heart of this mobility architecture evolution. It provides an open API that allows a
broader ecosystem of partners to access network intelligence in developing industry-relevant mobility solutions.
The Mobility Services Engine is part of the Cisco Unified Wireless Network, delivering a comprehensive approach
to business mobility - an approach that extends applications to the right device at the right time, no matter which
network is being used.
Mobility Services Architecture
Cisco Mobility Services are a set of value-added network services that consolidate intelligence from various points
in the network to enable and optimize the delivery of business mobility applications. This intelligence has typically
been highly distributed throughout the network, resulting in complex service provisioning and management. When
services, control, and data planes are combined in a single platform, the added complexity limits the network’s
ability to scale and adapt to new services while maintaining consistent performance.
The answer lies in centralized services architecture. While still critical to the ability of networks to provide the
intelligence for the optimal performance of mobile applications, mobility services should be abstracted from the
control and data planes in order to be centralized in the services engine. This centralization of services offers
several benefits, including scalability and improved provisioning and management. Additionally, centralized
services architecture removes the direct linkage between service and network, allowing services to extend across
wired and wireless networks.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 8
Increasingly, the mobility network must be able to support a great many applications at once. The true value of
mobility services is delivered through their ability to enhance application performance by providing real-time
information from the network and related applications. This cross-pollination of network and application
intelligence has a synergistic effect, augmenting the richness and breadth of the types of mobility solutions that
can be delivered. At the same time, a critical component of services delivery is helping to ensure that third-party
applications have a standard interface by which they can access this network and application intelligence.
The Cisco Mobility Services Engine supports an open API based on Simple Object Access Protocol/Extensible
Markup Language (SOAP/XML), which provides northbound access to these services to an ecosystem of mobility
application partners. With service intelligence centralized from the control network into the Mobility Services
Engine, IT can open access to the API without concern about disruption to the underlying production network.
Mobility Services Availability
The Cisco 3300 Series Mobility Services Engine is a combination of hardware and software infrastructure that
supports a suite of mobility services programs. Designed as an open platform, the Mobility Services Engine
supports mobility services software in a modular fashion, with various configuration options based on network
topology and the types of services required. The true value of the Mobility Services Engine is delivered through the
various mobility services applications. Cisco supports existing and future software, including:
●
Cisco Context-Aware Software: These programs capture and integrate into business processes detailed
contextual information about such things as location, RF interferers, temperature, availability, and
applications used. Context-aware applications feature a wide range of location options, including real-time
location, presence detection, historical visibility and impact of interferers, and telemetry of an asset.
Support for enhanced received signal strength indication (RSSI) and time difference of arrival (TDoA)
technology delivers accuracy and performance for a broad range of environments.
●
Cisco Adaptive Wireless Intrusion Prevention System (Adaptive wIPS) software provides visibility and
comprehensive threat prevention for the mobility network through monitoring, alerts, classifying, and
remediation of wireless and wired network vulnerabilities.
These services represent the initial suite of software supported on the Cisco Mobility Services Engine. Mobility
™
Services Engine integrates with Cisco CleanAir technology at a system level to provide crucial forensics and
policy enforcement capabilities. These capabilities make it possible for IT to provide mission-critical wireless
networking along with quick troubleshooting and problem resolution to create a self-healing, self-optimizing
wireless network. Cisco will deliver additional software services in the future. The Cisco Mobility Services Engine,
in conjunction with the services provided, increases productivity and improves a return on your investment.
Product Architecture
The Cisco 3300 Series Mobility Services Engine provides the following architectural elements:
●
A common API framework
●
A common management plane for services design, deployment, and operation (monitoring, reporting, and
troubleshooting)
◦
●
Management of services provided by the Cisco Wireless Control System (WCS)
Scalable infrastructure to support the instantiation of additional services
◦
Architecture allows services to span across multiple engines to facilitate flexibility in deployment
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 8
●
Loose coupling among services
◦
Facilitates easy integration into framework (plug and play)
◦
Message-Based Collaboration-Service Oriented Architecture (SOA) model, in which individual services
can be managed independently without affecting others
●
Integrated with the Cisco Unified Wireless Network
Figure 2 shows the Cisco 3300 Series Mobility Services Engine architecture.
Figure 2.
The Mobility Services Engine Architecture
Features and Benefits
The Cisco 3300 Series Mobility Services Engine delivers the following critical features and benefits:
●
Extensible platform for rapid delivery of services and applications
◦
Allows the abstraction of services and applications from control planes and the network so that each
may evolve independently
●
◦
Common framework for hosting multiple mobility services
◦
Open API to support third-party and partner application development
Ecosystem of application partners
◦
To deliver mobility solutions targeted at various industries, including healthcare, retail, education, and
manufacturing
●
Scalability
◦
Multiple services can be deployed on a single Cisco Mobility Services Engine, or a single service can
span multiple Cisco Mobility Services Engines
●
Manageability
◦
The Cisco Mobility Services Engine serves as a single point of integration for the various value-added
services
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 8
◦
All mobility services are managed centrally through the integration with the Cisco Wireless Control
System
●
Flexibility
◦
The Cisco Mobility Services Engine is an extensible platform capable of supporting a variety of services
configurations to meet business requirements. The architecture enables the inclusion of newer
technology standards as and when they become available
●
Return on investment
◦
The Cisco Mobility Services Engine integrates with the Cisco Unified Wireless Network to provide
network intelligence, including contextual information to optimize business applications. This architecture
builds upon the existing investment in Cisco wireless and mobility solutions and provides a platform that
is both flexible and scalable to meet evolving business mobility requirements
Product Specifications
Table 1 lists product specifications for the two models of the Cisco 3300 Series Mobility Services Engine.
Table 2 lists specifications for the Cisco Mobility Services Engine Virtual Appliance.
Table 1.
Cisco 3300 Series Mobility Services Engine Product Specifications (Physical Appliances)
Feature
Supported Services
Evaluation Support
Cisco 3310 Mobility Services Engine
● Cisco Context-Aware Software to track up to 2000
devices
● Cisco Adaptive Wireless Intrusion Prevention
System software to support up to 2000 monitor mode
access points
Cisco 3355 Mobility Services Engine
● Cisco Context-Aware Software to track up to 18000
devices
● Cisco Adaptive Wireless Intrusion Prevention
System software to support up to 3000 monitor mode
or enhanced local mode (ELM) access points
Customers who purchase a mobility service have the
option to try other mobility services on their MSE at the
following scale:
● Context-aware client tracking: 100 clients
Customers who purchase a mobility service have the
option to try other mobility services on their MSE at the
following scale:
● Context-aware client tracking: 100 clients
● Context-aware tag tracking: 100 tags
● Adaptive wireless intrusion prevention: 20 monitor
mode access points
● Context-aware tag tracking: 100 tags
● Adaptive wireless intrusion prevention: 20 monitor
mode or enhanced local mode access points
Processor
(1) Dual-Core Intel Processor 1.8 GHz
(2) Quad-Core Intel Nehalem Processor 2.0 GHz,
4-MB cache
Memory
4-GB PC2-5300 (4 x 1 GB)
16-GB DDR3 (2 x 8 GB)
Hard Disk
Two fixed 247-GB Serial ATA-150/SATA 300-MBps
drives
Four hot-swappable 146-GB SAS drives with up to
6-Gbps transfer rate
Removable Media
DVD/CD-RW combo drive
DVD-RO drive
Ports
● Serial: One 9-pin connector
● RJ-45: Two RJ-45 connectors for connection to two
Gigabit Network Adapters
● Three USB 2.0 ports: one front and two rear
accessible ports
● Two PS2 ports: One mouse and one keyboard
● Four USB ports: two in front, two in back
● Two VGA ports: one in front and one in back
● One RJ-45 management port for out-of-band
management
● RJ-45: Two rear RJ-45 connectors for connection to
two Gigabit Network Adapters
● One VGA port
Connectivity
Network: Two embedded Multifunction Gigabit Network
Adapters
Network: Two embedded Multifunction Gigabit Network
Adapters with TCP/IP offload engine
Management
SNMP v1, v2c, and v3
SNMP v1, v2c, and v3
Management Interface
Cisco WCS Mobility Services Version 5.2 or later
running Internet Explorer 6.0/Service Pack 1 or later
Cisco WCS Mobility Services Version 7.1 or later
running Internet Explorer 6.0/Service Pack 1 or later
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 8
Feature
Network Devices
System Specifications
Cisco 3310 Mobility Services Engine
Cisco 3355 Mobility Services Engine
● Cisco 2500 and 5500 Series Wireless LAN
Controllers
● Cisco Catalyst® 6500 Series Wireless Services
Module 2
● Cisco Wireless Controller on Cisco Services-Ready
Engine (SRE)
● Cisco Flex 7500 Series Cloud Controller
● Cisco 2500 and 5500 Series Wireless LAN
Controllers
● Cisco Catalyst® 6500 Series Wireless Services
Module 2
● Cisco Wireless Controller on Cisco Services-Ready
Engine (SRE)
● Cisco Flex 7500 Series Cloud Controller
● Cisco Aironet® Lightweight Access Points
● Cisco Aironet® Lightweight Access Points
● Number of MSEs per NCS: 10
● Number of Endpoints per Wireless LAN Controller:
● Number of MSEs per NCS: 10
● Number of Endpoints per Wireless LAN Controller:
◦
WLC 2500: 500
◦
WLC 2500: 500
◦
WLC on SRE for ISR G2: 500
◦
WLC on SRE for ISR G2: 500
◦
WLC 5500: 5,000
◦
WLC 5500: 5,000
◦
WiSM2: 5,000
◦
WiSM2: 5,000
◦
Flex7500: 5,000
◦
Flex7500: 5,000
Programming Interfaces
SOAP/XML APIs
SOAP/XML APIs
Form Factor
1RU
1RU
Physical Dimensions
Power
● Height: 1.70 in. (4.32 cm)
● Width: 16.78 in. (42.62 cm)
● Height: 1.69” (43mm)
● Width: 17.3” (440mm)
● Depth: 20 in.
● Weight: 15 lbs maximum
● Depth: 28.0” (711.4mm)
● Weight: 28 (minimum) - 35.1 lb (maximum)
(12.7 - 15.9 kg)
● AC power supply wattage: 540W
● AC power supply voltage: 100-120V at 50-60 Hz;
200-240V at 50-60 Hz
● AC power supply wattage: 625W
● AC power supply voltage: 100-120V at 50-60 Hz;
200-240V at 50-60 Hz
● 92% efficient
● Auto switching, hot-swappable
● Redundant power supplies
Cooling Fans
Environmental
Total of three fans
● Operating temperature:
◦
50 to 95°F (10 to 35°C) at sea level
● Nonoperating temperature:
◦
-40 to 158°F (-40 to 70°C) Maximum rate of
change is 20°C/hr (36°F/hr)
Total of six fans, 3+3 redundant configuration
● Operating temperature:
◦
50 to 95°F (10 to 35°C) up to 3000 ft/914.4m
◦
50 to 90°F (10 to 32°C) 3000 ft to 7000 ft/914.4m
to 2133m
● Nonoperating temperature:
◦
-40 to 140°F (-40 to 60°C)
◦
Maximum rate of change is 20°C/hr (36°F/hr)
● v Air temperature - Server on:
◦
10°C to 35°C (50°F to 95°F)
◦
Altitude: 0 to 914.4 m (3000 ft), Decrease system
temperature by 1.0°C for every 1000-foot increase
in altitude
● v Air temperature - Server off:
◦
5°C to 45°C (41°F to 113°F)
◦
Maximum altitude: 3048m (10000 ft)
● Shipment:
◦
-40°C to 60°C (-40°F to 140°F)
◦
Maximum altitude: 3048m (10000 ft)
● v Humidity - Server on:
◦
20% to 80%
◦
Maximum dew point: 21°C
◦
Maximum rate of change: 5°C/hr
● v Humidity - Server off:
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
◦
8% to 80%
◦
Maximum dew point: 27°C
Page 5 of 8
Feature
Cisco 3310 Mobility Services Engine
Approvals and Compliance
Software Compatibility
Table 2.
Cisco 3355 Mobility Services Engine
● Safety UL 60950
● CAN/CSA -C22.2 No. 60950
● Safety UL 60950
● CAN/CSA -C22.2 No. 60950
● EN60950
● IEC 60950: EMC FCC Part 15 (CFR 47) Class A
● EN60950
● IEC 60950: EMC FCC Part 15 (CFR 47) Class A
● ICES-003 Class A
● EN 55022 Class A
● ICES-003 Class A
● EN 55022 Class A
● CISPR22 Class A
● AS/NZS 3548 Class A
● CISPR22 Class A
● AS/NZS 3548 Class A
● VCCI Class A
● EN 55024
● VCCI Class A
● EN 55024
● EN 50082-1
● EN 50082-1
● Energy Star compliant
● Available with Cisco Mobility Services Engine (MSE)
Software Release 5.2 or later
● Requires Cisco Wireless LAN Controller (WLC)
Software Version 4.2.130 or later and Cisco
Wireless Control System (WCS) Version 5.2 or later
● Multiple mobility services can run concurrently on the
same MSE using WLC and MSE Software Release
6.0 or later
● Supported services may have different software
requirements
● Available with Cisco Mobility Services Engine (MSE)
Software Release 6.0 or later
● Requires Cisco Wireless LAN Controller (WLC)
Software Version 4.2.130 or later and Cisco
Wireless Control System (WCS) Version 6.0 or later
● Multiple mobility services can run con-currently on
the same MSE using WLC and MSE Software
Release 6.0 or later
● Supported services may have different software
requirements
Cisco Mobility Services Engine Virtual Appliance Product Specifications
VMWare ESXi Version
(Virtual Appliance on a CustomerSupplied Server)
VMWare ESX & ESXi version 4.1
Minimum Server Requirements
Cisco MSE High-End Virtual Appliance
● 50,000 Context-Aware License
● 10,000 aWIPS License
● Minimum RAM: 20GB
● Minimum Hard disk space allocation: 500GB
● Disk System Throughput: Minimum of 1600 IOPS with a bandwidth of 6000 Kbytes/sec
● Physical cores: 16 at 2.13GHz or better (2x Intel Xeon E7-L8867)
Cisco MSE Standard Virtual Appliance
● 18,000 Context-Aware License
● 5,000 aWIPS License
● Minimum RAM: 11GB
● Minimum Hard disk space allocation: 500GB
● Disk System Throughput: Minimum of 1000 IOPS with a bandwidth of 3500 Kbytes/sec
● Physical cores: 8 at 2.93GHz or better (2x Intel Xeon X5570)
Cisco MSE Low-End Virtual Appliance
● 2,000 Context-Aware License
● 2,000 aWIPS License
● Minimum RAM: 6GB
● Minimum Hard disk space allocation: 500GB
● Disk System Throughput: Minimum of 900 IOPS with a bandwidth of 3000 Kbytes/sec
● Physical cores: 2 at 2.93GHz or better (2x Intel Xeon X5570)
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 6 of 8
Virtual Appliance Reference HW Configs
●
●
●
UCS C460 M2 Rack Mount Server (High-End Virtual Appliance)
◦
Two Intel Xeon(R) CPU E7-L8867 @ 2.13GHz
◦
Disk System Throughput: Minimum of 1600 IOPS with a bandwidth of 6,000 Kbytes/sec
UCS C250 M2 Rack Mount Server (Standard Virtual Appliance)
◦
Two Intel Xeon(R) CPU E5570 @ 2.93GHz
◦
Disk System Throughput: Minimum of 1100 IOPS with a bandwidth of 4,000 Kbytes/sec
UCS C250 M2 Rack Mount Server (Low-End Virtual Appliance)
◦
Two Intel Xeon(R) CPU E5570 @ 2.93GHz
◦
Disk System Throughput: Minimum of 900 IOPS with a bandwidth of 3,000 Kbytes/sec
Summary
The Cisco 3300 Series Mobility Services Engine transforms existing wireless LANs into comprehensive mobility
networks through a uniform method of mobility services delivery. It integrates with the Cisco Unified Wireless
Network to build on existing business mobility investments. The variety of services, including the ability to collect
contextual information on people, interferers, and assets, optimizes business processes. The open API of the
Mobility Services Engines enables Cisco partners to expand the capabilities of the business mobility network and
to deliver relevant industry solutions.
Ordering Information
Table 3 lists ordering information for the Cisco 3300 Series Mobility Services Engine. To place an order, visit:
http://www.cisco.com/en/US/ordering/index.shtml.
Table 3.
Ordering Information
Part Number
Product Name
AIR-MSE-3355-K9
Cisco 3355 Series Mobility Services Engine
AIR-MSE-3310-K9
Cisco 3310 Series Mobility Services Engine
L-MSE-7.0-K9
Cisco Mobility Services Engine Virtual Appliance
Service and Support
Cisco Wireless LAN Services
Seamlessly integrate mobile services and take full advantage of the systemwide capabilities of the Cisco Unified
Wireless Network with services from Cisco and our partners. Better utilize the increased performance of the
802.11n standard while simplifying the transition to this new technology. For details, visit:
http://www.cisco.com/go/wirelesslanservices.
For More Information
For more information about Cisco Mobility Solutions, visit http://www.cisco.com/go/mse or contact your local Cisco
account representative.
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 7 of 8
Printed in USA
© 2012 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-475378-09
02/12
Page 8 of 8
APC Smart-UPS X 3000VA Rack/Tower LCD 100-127V
Page 1 of 4
ITEM 10
You are here: Home > Products > Uninterruptible Power Supply (UPS) > Network and Server > Smart-UPS
APC Smart-UPS X 3000VA Rack/Tower LCD 100-127V
Part Number: SMX3000RMLV2U
Technical Specifications
Product Overview
Documentation
Software & Firmware
Options
Ratings and Reviews
Output
Output Power Capacity
2700 Watts / 3000 VA
Max Configurable Power
2700 Watts / 3000 VA
Nominal Output Voltage
120V
Output Voltage Distortion
Less than 5% at full load
Output Frequency (sync to mains) 47 - 53 Hz for 50 Hz nominal, 57 - 63 Hz for 60 Hz nominal
Topology
Line Interactive
Waveform Type
Sine wave
Output Connections
(3) NEMA 5-15R
(3) NEMA 5-20R
(1) NEMA L5-30R
Input
Nominal Input Voltage
120V
Input Frequency
50/60 Hz +/- 3 Hz (auto sensing)
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMX3000R...
5/1/2013
APC Smart-UPS X 3000VA Rack/Tower LCD 100-127V
Input Connections
NEMA L5-30P
Cord Length
8 feet (2.44 meters)
Input voltage range for main
operations
70 - 153V
Transfer Time
2-4 ms
Page 2 of 4
Batteries & Runtime
Battery Type
Maintenance-free sealed Lead-Acid battery with suspended electrolyte : leakproof
Typical recharge time
3 hour(s)
Replacement Battery
APCRBC117
RBC™ Quantity
1
Extended Run Options
APC Smart-UPS X 3000VA Rack/Tower LCD 100-127V
Runtime Graph
Curve
Part Number(s)
A
SMX3000RMLV2U
SMX3000RMLV2U
B
+ (1)
SMX120RMBP2U
SMX3000RMLV2U
C
+ (2)
SMX120RMBP2U
SMX3000RMLV2U
D
+ (3)
SMX120RMBP2U
SMX3000RMLV2U
E
+ (4)
SMX120RMBP2U
Hover over the line on the graph above to view the runtime at any desired load
Curve fit to measured runtime data. All measurements taken with new, fully charged batteries, at typical
environmental conditions, with no electrical input and balanced resistive load (PF = 1.0) output.
View Enlarged Graph
View Runtime Chart
Energy Use/Efficiency
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMX3000R...
5/1/2013
APC Smart-UPS X 3000VA Rack/Tower LCD 100-127V
Load
Efficiency
25%
95.9%
50%
97.4%
75%
97.6%
100%
97.5%
Page 3 of 4
Hover over the line on the graph above to view the efficiency at any desired load
Curve fit to measured efficiency data. All measurements taken in normal operating mode, at typical
environmental conditions, with nominal electrical input and balanced resistive load (PF = 1.0) output.
View Enlarged Graph
Communications & Management
Interface Port(s)
SmartSlot
Available SmartSlot™ Interface
Quantity
1
Control panel
LED status display with On Line : On Battery : Replace Battery and Overload
indicators, Multi-function LCD status and control console
Audible Alarm
Alarm when on battery : distinctive low battery alarm : configurable delays
Emergency Power Off (EPO)
Yes
Surge Protection and Filtering
Surge energy rating
540 Joules
Filtering
Full time multi-pole noise filtering : 0.3% IEEE surge let-through : zero clamping
response time : meets UL 1449
Data Line Protection
--
Physical
Maximum Height
3.36 inches (85 mm)
Maximum Width
17.00 inches (432 mm)
Maximum Depth
26.26 inches (667 mm)
Rack Height
2U
Net Weight
84.60 lbs. (38.45 kg)
Shipping Weight
99.79 lbs. (45.36 kg)
Shipping Height
9.58 inches (243 mm)
Shipping Width
23.48 inches (596 mm)
Shipping Depth
34.23 inches (869 mm)
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMX3000R...
5/1/2013
APC Smart-UPS X 3000VA Rack/Tower LCD 100-127V
Color
Black
Units per Pallet
8.00
# of Layers per Pallet
4
# of Units per Layer per Pallet
2
Pallet Weight
855.12 lbs. (388.69 kg)
Page 4 of 4
Environmental
Operating Environment
32 - 104 °F (0 - 40 °C)
Operating Relative Humidity
0 - 95%
Operating Elevation
0-10000 feet (0-3000 meters)
Storage Temperature
5 - 113 °F (-15 - 45 °C)
Storage Relative Humidity
0 - 95%
Storage Elevation
0-50000 feet (0-15000 meters)
Audible noise at 1 meter from
surface of unit
55.00 dBA
Online Thermal Dissipation
276.00 BTU/hr
Conformance
Regulatory Approvals
BSMI, CSA, EN 50091-2, EN 55022 Class A, FCC Part 15 Class A, NOM, TUV, UL
1778, VCCI Class A
Standard Warranty
3 years repair or replace (excluding battery) and 2 year for battery, optional on-site
warranties available, optional extended warranties available
Equipment protection policy
Lifetime : $150000
Sustainable Offer Status
RoHS
Compliant
REACH
REACH: Contains No SVHCs
PEP
Available in Documentation tab
EOLI
Available in Documentation tab
*Except where noted, all prices are Estimated Resale Price (ERP) - Without Tax/VAT. Pricing in other locations and sites may vary.
**The time to recharge to 90% of full battery capacity following a discharge to shutdown using a load rated for 1/2 the full load rating of the UPS.
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMX3000R...
5/1/2013
APC Smart-UPS X 120V External Battery Pack Rack/Tower
Page 1 of 2
You are here: Home > Products > Smart-UPS Battery Systems
APC Smart-UPS X 120V External Battery Pack
Rack/Tower
Part Number: SMX120RMBP2U
Technical Specifications
Product Overview
Documentation
Options
Ratings and Reviews
Output
battoutvolt
120
Batteries & Runtime
Battery Volt-Amp-Hour Capacity 1200
Battery Type
Maintenance-free sealed Lead-Acid battery with suspended electrolyte :
leakproof
Battery mounting
Enclosed battery cartridge
Battery manufacturer
--
Expected Battery Life (years)
3-5
RBC™ Quantity
2
Battery blocks per string
10
Physical
Net Weight
124.00 lbs. (56.36 kg)
Maximum Height
3.36 inches (85 mm)
Maximum Width
17.00 inches (432 mm)
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMX120RM... 5/1/2013
APC Smart-UPS X 120V External Battery Pack Rack/Tower
Maximum Depth
26.26 inches (667 mm)
Shipping Weight
140.00 lbs. (63.64 kg)
Shipping Width
23.48 inches (596 mm)
Shipping Height
9.58 inches (243 mm)
Shipping Depth
34.23 inches (869 mm)
Rack Height
2U
Color
Black
Units per Pallet
8.00
Page 2 of 2
Environmental
Operating Environment
32 - 104 °F (0 - 40 °C)
Operating Relative Humidity
0 - 95%
Operating Elevation
0-10000 feet (0-3000 meters)
Storage Temperature
5 - 113 °F (-15 - 45 °C)
Storage Relative Humidity
0 - 95%
Storage Elevation
0-50000 feet (0-15000 meters)
Conformance
Standard Warranty
2 years repair or replace
Sustainable Offer Status
RoHS
Compliant
REACH
REACH: Contains No SVHCs
PEP
Available in Documentation tab
EOLI
Available in Documentation tab
*Except where noted, all prices are Estimated Resale Price (ERP) - Without Tax/VAT. Pricing in other locations and sites may vary.
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMX120RM... 5/1/2013
APC Smart-UPS 3000VA LCD RM 2U 120V
Page 1 of 4
ITEM 11
You are here: Home > Products > Uninterruptible Power Supply (UPS) > Network and Server > Smart-UPS
APC Smart-UPS 3000VA LCD RM 2U 120V
Part Number: SMT3000RM2U
Technical Specifications
Product Overview
Documentation
Software & Firmware
Options
Ratings and Reviews
Output
Output Power Capacity
2700 Watts / 2880 VA
Nominal Output Voltage
120V
Output Voltage Distortion
Less than 5%
Output Frequency (sync to mains) 50/60Hz +/- 3 Hz
Topology
Line Interactive
Waveform Type
Sine wave
Output Connections
(6) NEMA 5-15R
(2) NEMA 5-20R
Input
Nominal Input Voltage
120V
Input Frequency
50/60 Hz +/- 3 Hz (auto sensing)
Input Connections
NEMA L5-30P
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT3000R...
5/1/2013
APC Smart-UPS 3000VA LCD RM 2U 120V
Cord Length
8 feet (2.44 meters)
Input voltage range for main
operations
82 - 144V
Input voltage adjustable range for
mains operation
75 - 154V
Page 2 of 4
Batteries & Runtime
Battery Type
Maintenance-free sealed Lead-Acid battery with suspended electrolyte : leakproof
Typical recharge time
3 hour(s)
Replacement Battery
RBC43
RBC™ Quantity
1
Runtime Graph
Hover over the line on the graph above to view the runtime at any desired load
Curve fit to measured runtime data. All measurements taken with new, fully charged batteries, at typical
environmental conditions, with no electrical input and balanced resistive load (PF = 1.0) output.
View Enlarged Graph
View Runtime Chart
Energy Use/Efficiency
Load
Efficiency
25%
97.9%
50%
98.5%
75%
98.4%
100%
98.2%
Hover over the line on the graph above to view the efficiency at any desired load
Curve fit of data measured in accordance with the ENERGY STAR Program Requirements Product
Specification for Uninterruptible Power Supplies (UPSs) - Eligibility Criteria Version 1.0. All measurements
taken in normal mode(s), at typical environmental conditions, with 120V/60Hz electrical input and
balanced resistive load (PF = 1.0) output.
View Enlarged Graph
Communications & Management
Interface Port(s)
USB
Available SmartSlot™ Interface
Quantity
1
Control panel
LED status display with On Line : On Battery : Replace Battery and Overload
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT3000R...
5/1/2013
APC Smart-UPS 3000VA LCD RM 2U 120V
Page 3 of 4
indicators, Multi-function LCD status and control console
Audible Alarm
Alarm when on battery : distinctive low battery alarm : overload continuous tone alarm
Surge Protection and Filtering
Surge energy rating
459 Joules
Physical
Maximum Height
3.39 inches (86 mm)
Maximum Width
18.90 inches (480 mm)
Maximum Depth
26.89 inches (683 mm)
Rack Height
2U
Net Weight
97.42 lbs. (44.28 kg)
Shipping Weight
113.74 lbs. (51.70 kg)
Shipping Height
10.00 inches (254 mm)
Shipping Width
23.62 inches (600 mm)
Shipping Depth
38.60 inches (980 mm)
Color
Black
Units per Pallet
8.00
Environmental
Operating Environment
32 - 104 °F (0 - 40 °C)
Operating Relative Humidity
0 - 95%
Operating Elevation
0-10000 feet (0-3000 meters)
Storage Temperature
5 - 113 °F (-15 - 45 °C)
Storage Relative Humidity
0 - 95%
Storage Elevation
0-50000 feet (0-15000 meters)
Audible noise at 1 meter from
surface of unit
55.00 dBA
Online Thermal Dissipation
348.00 BTU/hr
Conformance
Regulatory Approvals
CSA, ENERGY STAR (USA), FCC Part 15 Class A, UL 1778
Standard Warranty
3 years repair or replace (excluding battery) and 2 year for battery
Equipment protection policy
Lifetime : $150000
Sustainable Offer Status
RoHS
Compliant
REACH
REACH: Contains No SVHCs
PEP
Available in Documentation tab
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT3000R...
5/1/2013
APC Smart-UPS 3000VA LCD RM 2U 120V
EOLI
Page 4 of 4
Available in Documentation tab
*Except where noted, all prices are Estimated Resale Price (ERP) - Without Tax/VAT. Pricing in other locations and sites may vary.
**The time to recharge to 90% of full battery capacity following a discharge to shutdown using a load rated for 1/2 the full load rating of the UPS.
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT3000R...
5/1/2013
APC Smart-UPS 2200VA RM 2U LCD 120V
Page 1 of 5
ITEM 12
You are here: Home > Products > Uninterruptible Power Supply (UPS) > Network and Server > Smart-UPS
APC Smart-UPS 2200VA RM 2U LCD
120V
Part Number: SMT2200RM2U
Technical
Specifications
Product
Overview
Documentation
Software &
Firmware
Options
Ratings and
Reviews
Output
Output Power Capacity
1980 Watts / 2200 VA
Max Configurable Power
1980 Watts / 2200 VA
Nominal Output Voltage
120V
Waveform Type
Sine wave
Output Connections
(6) NEMA 5-15R
(2) NEMA 5-20R
Input
Nominal Input Voltage
120V
Input Frequency
50/60 Hz +/- 3 Hz (auto sensing)
Input Connections
NEMA 5-20P
Cord Length
8 feet (2.44 meters)
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT2200R... 4/12/2012
APC Smart-UPS 2200VA RM 2U LCD 120V
Page 2 of 5
Input voltage range for main 82 - 143V
operations
Input voltage adjustable
range for mains operation
75 - 154V
Batteries & Runtime
Battery Type
Maintenance-free sealed Lead-Acid battery with suspended electrolyte :
leakproof
Typical recharge time
3 hour(s)
Replacement Battery
RBC43
RBC™ Quantity
1
Runtime Graph
Hover over the line on the graph above to view the runtime at any
desired load
Curve fit to measured runtime data. All measurements taken with
new, fully charged batteries, at typical environmental conditions, with
no electrical input and balanced resistive load (PF = 1.0) output.
View Enlarged Graph
View Runtime Chart
Energy Use/Efficiency
Load
Efficiency
25%
97.0%
50%
97.5%
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT2200R... 4/12/2012
APC Smart-UPS 2200VA RM 2U LCD 120V
75%
97.3%
100%
96.9%
Page 3 of 5
Hover over the line on the graph above to view the efficiency at any
desired load
Curve fit to measured efficiency data All measurements taken in
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT2200R... 4/12/2012
APC Smart-UPS 2200VA RM 2U LCD 120V
Page 4 of 5
Communications & Management
Interface Port(s)
USB
Available SmartSlot™
Interface Quantity
1
Control panel
LED status display with On Line : On Battery : Replace Battery and
Overload indicators,Multi-function LCD status and control console
Audible Alarm
Alarm when on battery : distinctive low battery alarm : overload
continuous tone alarm
Emergency Power Off (EPO) Yes
Surge Protection and Filtering
Surge energy rating
530 Joules
Physical
Maximum Height
3.39 inches (86 mm)
Maximum Width
18.90 inches (480 mm)
Maximum Depth
26.89 inches (683 mm)
Rack Height
2U
Net Weight
93.08 lbs. (42.31 kg)
Shipping Weight
109.41 lbs. (49.73 kg)
Shipping Height
10.00 inches (254 mm)
Shipping Width
23.62 inches (600 mm)
Shipping Depth
38.60 inches (980 mm)
Color
Black
Units per Pallet
8.00
Environmental
Operating Environment
32 - 104 °F (0 - 40 °C)
Operating Relative Humidity 0 - 95%
Operating Elevation
0-10000 feet (0-3000 meters)
Storage Temperature
5 - 113 °F (-15 - 45 °C)
Storage Relative Humidity
0 - 95%
Storage Elevation
0-50000 feet (0-15000 meters)
Audible noise at 1 meter
from surface of unit
55.00 dBA
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT2200R... 4/12/2012
APC Smart-UPS 2200VA RM 2U LCD 120V
Page 5 of 5
Online Thermal Dissipation 215.00 BTU/hr
Conformance
Regulatory Approvals
CSA,FCC Part 15 Class A,UL 1778
Standard Warranty
3 years repair or replace (excluding battery) and 2 year for battery
Equipment protection policy Lifetime : $150000
Environmental Compliance RoHS 7b Exemption,REACH: Contains No SVHCs
*Except where noted, all prices are Estimated Resale Price (ERP) - Without Tax/VAT. Pricing in other
locations and sites may vary.
**The time to recharge to 90% of full battery capacity following a discharge to shutdown using a load
rated for 1/2 the full load rating of the UPS.
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=SMT2200R... 4/12/2012
UPS Network Management Card 2
Page 1 of 2
ITEM 13
Home
Products
Uninterruptible Power Supply (UPS)
UPS Management
Product Family
UPS
Network
Management
Card 2
Part Number:
AP9630
Communications & Management
Protocols
HTTP,HTTPS,IPv4,IPv6,NTP,SMTP,SNMP v1,SNMP v3,SSH V1,SSH
V2,SSL,TCP/IP,Telnet
Network Interface Connections RJ-45 10/100 Base-T
Authentication
Radius
Physical
Net Weight
0.18 lbs. (0.08 kg)
Maximum Height
1.50 inches (38 mm)
Maximum Width
4.75 inches (121 mm)
Maximum Depth
4.50 inches (114 mm)
Shipping Weight
0.75 lbs. (0.34 kg)
Shipping Height
2.00 inches (51 mm)
Shipping Width
9.25 inches (235 mm)
Shipping Depth
6.25 inches (159 mm)
Color
Black
Environmental
Operating Environment
32 - 113 °F (0 - 45 °C)
Storage Temperature
23 - 113 °F (-5 - 45 °C)
Operating Relative Humidity 0 - 95%
Storage Relative Humidity
0 - 95%
Operating Elevation
0-10000 feet (0-3000 meters)
Storage Elevation
0-50000 feet (0-15000 meters)
Conformance
Regulatory Approvals
AS/NZS 3548 (C-Tick) Class A,EN 55022 Class A,EN 55024,FCC Part 15
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=AP9630&t... 11/23/2010
UPS Network Management Card 2
Page 2 of 2
Class A,GOST,ICES-003,VCCI Class A
Standard Warranty
2 years repair or replace
Environmental Compliance
RoHS,REACH: Contains No SVHCs,Contains Lithium Battery
*Except where noted, all prices are Estimated Resale Price (ERP) - Without Tax/VAT. Pricing in other
locations and sites may vary.
Copyright © American Power Conversion Corp., all rights reserved
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=AP9630&t... 11/23/2010
Rack PDU, Metered, Zero U, 30A, 120V, (24) 5-20
Page 1 of 2
ITEM 14
You are here: Home > Products > Power Distribution > Rack Power Distribution > Metered Rack PDU
Rack PDU, Metered, Zero U, 30A, 120V, (24) 5-20
Part Number: AP7832
Technical Specifications
Product Overview
Documentation
Software & Firmware
Options
Output
Nominal Output Voltage
120V
Maximum Total Current Draw
per Phase
24A
Output Connections
(24) NEMA 5-20R
Overload Protection
Yes
Input
Nominal Input Voltage
100V, 120V
Input Frequency
50/60 Hz
Regulatory Derated Input
Current (North America)
24A
Input Connections
NEMA L5-30P
Cord Length
10 feet (3.05 meters)
Number of Power Cords
1
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=AP7832&tab... 5/1/2013
Rack PDU, Metered, Zero U, 30A, 120V, (24) 5-20
Maximum Input Current per
phase
30A
Load Capacity
2880 VA
Page 2 of 2
Physical
Net Weight
12.50 lbs. (5.68 kg)
Maximum Height
63.75 inches (1619 mm)
Maximum Width
2.19 inches (56 mm)
Maximum Depth
1.73 inches (44 mm)
Shipping Weight
14.50 lbs. (6.59 kg)
Shipping Height
84.00 inches (2134 mm)
Shipping Width
6.00 inches (152 mm)
Shipping Depth
5.00 inches (127 mm)
Color
Black
Environmental
Operating Environment
32 - 113 °F (0 - 45 °C)
Operating Relative Humidity
5 - 95%
Operating Elevation
0-10000 feet (0-3000 meters)
Storage Temperature
-13 - 149 °F (-25 - 65 °C)
Storage Relative Humidity
5 - 95%
Storage Elevation
0-50000 feet (0-15000 meters)
Conformance
Regulatory Approvals
cUL Listed, CSA C22.2 No. 60950-1-03, FCC Part 15 Class A, ICES-003,
Industry Canada, UL 60950, UL 60950-1
Standard Warranty
2 years repair or replace
Sustainable Offer Status
RoHS
Compliant
REACH
REACH: Contains No SVHCs
PEP
Available in Documentation tab
EOLI
Available in Documentation tab
Battery Directive
Compliant
Battery Notes
Contains Lithium Battery
*Except where noted, all prices are Estimated Resale Price (ERP) - Without Tax/VAT. Pricing in other locations and sites may vary.
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=AP7832&tab... 5/1/2013
Rack PDU, Metered, Zero U, 20A, 120V, (24) NEMA 5-20R
Page 1 of 2
ITEM 15
You are here: Home > Products > Power Distribution > Rack Power Distribution > Metered Rack PDU
Rack PDU, Metered, Zero U, 20A, 120V, (24) NEMA 520R
Part Number: AP7830
Technical Specifications
Product Overview
Documentation
Software & Firmware
Options
Output
Nominal Output Voltage
120V
Maximum Total Current Draw
per Phase
20A
Output Connections
(24) NEMA 5-20R
Overload Protection
No
Input
Nominal Input Voltage
100V, 120V
Input Frequency
50/60 Hz
Regulatory Derated Input
Current (North America)
16A
Input Connections
NEMA L5-20P
Cord Length
10 feet (3.05 meters)
Number of Power Cords
1
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=AP7830&ta... 1/18/2013
Rack PDU, Metered, Zero U, 20A, 120V, (24) NEMA 5-20R
Maximum Input Current per
phase
20A
Load Capacity
1920 VA
Page 2 of 2
Physical
Net Weight
15.00 lbs. (6.82 kg)
Maximum Height
63.75 inches (1619 mm)
Maximum Width
2.19 inches (56 mm)
Maximum Depth
1.73 inches (44 mm)
Shipping Weight
17.00 lbs. (7.73 kg)
Shipping Height
84.00 inches (2134 mm)
Shipping Width
6.00 inches (152 mm)
Shipping Depth
5.00 inches (127 mm)
Color
Black
Environmental
Operating Environment
23 - 113 °F (-5 - 45 °C)
Operating Relative Humidity
0 - 95%
Operating Elevation
0-10000 feet (0-3000 meters)
Storage Temperature
-13 - 149 °F (-25 - 65 °C)
Storage Relative Humidity
0 - 95%
Storage Elevation
0-50000 feet (0-15000 meters)
Conformance
Regulatory Approvals
cUL Listed, CSA C22.2 No. 60950-1-03, FCC Part 15 Class A, ICES-003,
Industry Canada, UL 60950-1, UL Listed
Standard Warranty
2 years repair or replace
Sustainable Offer Status
RoHS
Compliant
REACH
REACH: Contains No SVHCs
PEP
Available in Documentation tab
EOLI
Available in Documentation tab
Battery Directive
Compliant
Battery Notes
Contains Lithium Battery
*Except where noted, all prices are Estimated Resale Price (ERP) - Without Tax/VAT. Pricing in other locations and sites may vary.
http://www.apc.com/products/resource/include/techspec_index.cfm?base_sku=AP7830&ta... 1/18/2013
ITEM 16
Data Sheet
Cisco Small Form-Factor Pluggable Modules for
Gigabit Ethernet Applications
The industry-standard Cisco® Small Form-Factor Pluggable (SFP) Gigabit Interface
Converter is a hot-swappable input/output device that plugs into a Gigabit Ethernet
port or slot, linking the port with the network (Figures 1, 2 and 3). SFPs can be used
and interchanged on a wide variety of Cisco products and can be intermixed in
combinations of 1000BASE-T, 1000BASE-SX, 1000BASE-LX/LH, 1000BASE-EX,
1000BASE-ZX, or 1000BASE-BX10-D/U on a port-by-port basis.
Figure 1.
Cisco optical Gigabit Ethernet SFP
Figure 2.
Cisco 1000BASE-T Copper SFP
Figure 3.
Cisco 2-channel 1000BASE-BX optical SFP
1000BASE-T SFP for Copper Networks
The 1000BASE-T SFP operates on standard Category 5 unshielded twisted pair copper cabling of up to 100m
(328 ft) link length. Cisco 1000BASE-T SFP modules support 10/100/1000 autonegotiation and Auto MDI/MDIX.
1000BASE-SX SFP for Multimode Fiber Only
The 1000BASE-SX SFP, compatible with the IEEE 802.3z 1000BASE-SX standard, operates on legacy 50 µm
multimode fiber links up to 550 m and on 62.5 µm Fiber Distributed Data Interface (FDDI)-grade multimode fibers
up to 220 m. It can support up to 1km over laser-optimized 50 µm multimode fiber cable.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 1 of 6
1000BASE-LX/LH SFP for Both Multimode and Single-Mode Fibers
The 1000BASE-LX/LH SFP, compatible with the IEEE 802.3z 1000BASE-LX standard, operates on standard
single-mode fiber-optic link spans of up to 10 km and up to 550 m on any multimode fibers. When used over
legacy multimode fiber type, the transmitter should be coupled through a mode conditioning patch cable. For
details on this implementation, refer to
http://www.cisco.com/en/US/prod/collateral/modules/ps5455/product_bulletin_c25-530836.html.
1000BASE-EX SFP for Long-Reach Single-Mode Fibers
The 1000BASE-EX SFP operates on standard single-mode fiber-optic link spans of up to 40 km in length. A 5-dB
inline optical attenuator should be inserted between the fiber-optic cable and the receiving port on the SFP at each
end of the link for back-to-back connectivity.
1000BASE-ZX SFP for Long-Reach Single-Mode Fibers
The 1000BASE-ZX SFP operates on standard single-mode fiber-optic link spans of up to approximately 70 km in
length. The SFP provides an optical link budget of 21 dB, but the precise link span length depends on multiple
factors such as fiber quality, number of splices, and connectors.
When shorter distances of single-mode fiber (SMF) are used, it might be necessary to insert an inline optical
attenuator in the link to avoid overloading the receiver. A 10-dB inline optical attenuator should be inserted
between the fiber-optic cable plant and the receiving port on the SFP at each end of the link whenever the fiberoptic cable span loss is less than 8 dB.
1000BASE-BX10-D and 1000BASE-BX10-U SFP for Single-Fiber Bidirectional Applications
The 1000BASE-BX-D and 1000BASE-BX-U SFPs, compatible with the IEEE 802.3ah 1000BASE-BX10-D and
1000BASE-BX10-U standards, operate on a single strand of standard SMF.
A 1000BASE-BX10-D device is always connected to a 1000BASE-BX10-U device with a single strand of standard
SMF with an operating transmission range up to 10 km.
The communication over a single strand of fiber is achieved by separating the transmission wavelength of the two
devices as depicted in Figure 3: 1000BASE-BX10-D transmits a 1490-nm channel and receives a 1310-nm signal,
whereas 1000BASE-BX10-U transmits at a 1310-nm wavelength and receives a 1490-nm signal. Note in Figure 3
the presence of a wavelength-division multiplexing (WDM) splitter integrated into the SFP to split the 1310-nm and
1490-nm light paths.
Figure 4.
Bidirectional Transmission of a Single Strand of SMF
The GLC-BX-D and GLC-BX-U SFPs also support digital optical monitoring (DOM) functions according to the
industry-standard SFF-8472 multisource agreement (MSA). This feature gives the end user the ability to monitor
real-time parameters of the SFP, such as optical output power, optical input power, temperature, laser bias
current, and transceiver supply voltage.
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 2 of 6
2-channel 1000BASE-BX10-D for Single-Fiber Bidirectional Applications
The 2-channel 1000BASE-BX-D SFP module, also known as Compact SFP, integrates two IEEE 802.3ah
1000BASE-BX10-D interfaces in one SFP module. The GLC-2BX-D is always connected to two 1000BASE-BX10U interfaces over two single strands of standard SMF with an operating transmission range up to 10km.
GLC-2BX-D is designed to connect to any standard-based Customer Premises Equipment (CPE) in FTTx links
(Figure 5).
Figure 5.
Compact SFP deployment with Catalyst 4500
Technical Specifications
Platform Support
The Cisco SFPs are supported across a variety of Cisco switches, routers, and optical transport devices. For more
details, refer to the document SFP Compatibility Matrix at
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matrix/OL_6981.pdf.
Connectors and Cabling
Connectors include the following:
●
Dual LC/PC connector (1000BASE-SX, 1000BASE-LX/LH, 1000BASE-EX and 1000BASE-ZX)
●
Single LC/PC connector (1000BASE-BX-D and 1000BASE-BX-U)
●
RJ-45 connector (1000BASE-T)
Note:
Only connections with patch cords with PC or UPC connectors are supported. Patch cords with APC
connectors are not supported. All cables and cable assemblies used must be compliant with the standards
specified in the standards section.
Table 1 provides cabling specifications for the SFPs that you install in the Gigabit Ethernet port. Note that all SFP
ports have LC-type connectors, and the minimum cable distance for all SFPs listed (multimode and single-mode
fiber) is 6.5 feet (2 m).
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 3 of 6
Table 1.
SFP Port Cabling Specifications
Product
Wavelength (nm)
Fiber Type
Core Size (µm)
Modal Bandwidth
(MHz* Km)***
Operating Distance
(m)
1000BASE-SX
850
MMF
62.5
160 (FDDI-grade)
220 (722 ft)
62.5
200 (OM1)
275 (902 ft)
50
400
500 (1,640 ft)
50
500 (OM2)
550 (1,804 ft)
50
2000 (OM3)
1000 (3281 ft)
62.5
500
550 (1,804 ft)
50
400
550 (1,804 ft)
1000BASE-LX/LH
1310
MMF*
50
500
550 (1,804 ft)
SMF
-**
-
10,000 (32,821 ft)
1000BASE-EX
1310
SMF
-**
-
40,000 (131,234 ft)
1000BASE-ZX
1550
SMF
-
-
Approximately 70 km
depending on link loss
1000BASE-BX-U
1310
SMF
-**
-
10,000 (32,821 ft)
1000BASE-BX-D
1490
SMF
-**
-
10,000 (32,821 ft)
*
A mode-conditioning patch cord, as specified by the IEEE standard, is required regardless of the span length. Note how the
mode conditioning patch cord for 62.5-µm fibers has a different specification from the mode-conditioning patch cord for 50-µm
fibers.
**
ITU-T G.652 SMF as specified by the IEEE 802.3z standard.
***
Specified at transmission wavelength.
Optical Specifications
Table 2 gives optical parameters for the SFPs.
Table 2.
Main Optical Parameters
Product
Transmit Power Range (dBm)
Receive Power Range (dBm)
Transmit and Receive
Wavelength Range (nm)
1000BASE-SX
-3 to -9.5
0 to -17
770 to 860
1000BASE-LX/LH
-3 to -9.5
-3 to -20
1270 to 1355
1000BASE-EX
+3 to -1
+1 to -22
1290 to 1335
1000BASE-ZX
+5 to 0
-3 to -23
1500 to 1580
1000BASE-BX10-D
-3 to -9
-3 to -19.5
1480 to 1500 (Transmit)
1260 to 1360 (Receive)
1000BASE-BX10-U
-3 to -9
-3 to -19.5
1260 to 1360 (Transmit)
1480 to 1500 (Receive)
Dimensions
Dimensions (H x W x D): 8.5 x 13.4 x 56.5 mm. Cisco SFPs typically weigh 75 grams or less.
Environmental Conditions and Power Requirements
Operating temperature range:
●
Commercial temperature range (COM): 0 to 70°C (32 t o 158°F)
●
Extended temperature range (EXT): -5°C to 85°C (23 to 185°F)
●
Industrial temperature range (IND): -40 to 85°C (-4 0 to 185°F)
●
Storage temperature range: -40 to 85°C (-40 to 185° F)
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 4 of 6
Cisco SFP modules typically consume up to 1W per SFP port, with the exception of the Compact SFP
(GLC-2BX-D) consuming up to 1.5W.
Table 3 gives temperature range and DOM support information for the SFPs.
Table 3.
Temperature Range and DOM Support
Product Number
Temperature Range
DOM
GLC-SX-MM
COM
No
GLC-LH-SM
COM
No
GLC-ZX-SM
COM
Yes
GLC-BX-U
COM
Yes
GLC-BX-D
COM
Yes
GLC-2BX-D
COM
Yes
GLC-T
COM
n/a
SFP-GE-T
EXT
n/a
SFP-GE-S
EXT
Yes
SFP-GE-L
EXT
Yes
SFP-GE-Z
EXT
Yes
GLC-SX-MMD
EXT
Yes
GLC-LH-SMD
EXT
Yes
GLC-EX-SMD
EXT
Yes
GLC-SX-MM-RGD
IND
No
GLC-LX-SM-RGD
IND
No
GLC-ZX-SM-RGD
IND
No
Warranty
●
Standard warranty: 90 days
●
Extended warranty (option): Available under a Cisco SMARTnet Service support contract for the Cisco
®
switch or router chassis
Regulatory and Standards Compliance
Safety:
●
Laser Class I 21CFR1040 LN#50 7/2001
●
Laser Class I IEC 60825-1
Standards:
●
IEEE 802.3z
●
IEEE 802.3ah
GR-20-CORE: Generic Requirements for Optical Fiber and Optical Fiber Cable
GR-326-CORE: Generic Requirements for Single-Mode Optical Connectors and Jumper Assemblies
GR-1435-CORE: Generic Requirements for Multifiber Optical Connectors
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
Page 5 of 6
Ordering Information
To place an order, visit the Cisco Ordering homepage or refer to Table 4.
Table 4.
Ordering Information
Product Description
Product Number
1000BASE-T standard
GLC-T
1000BASE-SX short wavelength; without DOM
GLC-SX-MM
1000BASE-LX/LH long-wavelength/long haul; without DOM
GLC-LH-SM
1000BASE-ZX extended distance
GLC-ZX-SM
1000BASE-BX10-D downstream bidirectional single fiber; with DOM
GLC-BX-D
2-channel 1000BASE-BX10-D downstream bidirectional single fiber; with DOM
GLC-2BX-D
1000BASE-BX10-U upstream bidirectional single fiber; with DOM
GLC-BX-U
1000BASE-T NEBS 3 ESD
SFP-GE-T
1000BASE-SX short wavelength; with DOM
SFP-GE-S
GLC-SX-MMD
1000BASE-LX/LH long-wavelength; with DOM
SFP-GE-L
GLC-LH-SMD
1000BASE-EX long-wavelength; with DOM
GLC-EX-SMD
1000BASE-ZX extended distance; with DOM
SFP-GE-Z
1000BASE-SX short wavelength; rugged
GLC-SX-MM-RGD
1000BASE-LX/LH long wavelength; rugged
GLC-LX-SM-RGD
1000BASE-ZX extended distance; rugged
GLC-ZX-SM-RGD
Printed in USA
© 2011 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public Information.
C78-366584-07
11/11
Page 6 of 6
ER 1-11 (Area 1B)
TR 1-11 (Area 1D)
Switch 1 – 24 Port 10/100/1000 POE
ER 1-11 (Area 1B)
Switch 2 – 24 Port 10/100/1000 POE
Switch 3 – 48 Port 10/100/1000
TR 1-11 (Area 1D)
TR 1-12 (Area 1A)
45
45
45
45
45
45
45
45
45
45
44
44
44
44
44
44
44
44
44
44
43
43
43
43
43
43
43
43
43
43
42
42
42
42
42
42
42
42
42
42
41
41
41
41
41
41
41
41
41
41
40
40
40
40
40
40
40
40
40
40
39
39
39
39
39
39
39
39
39
39
38
38
38
38
38
38
38
38
38
38
37
37
37
37
37
37
37
37
37
37
36
36
36
36
36
36
36
36
36
36
35
35
35
35
35
35
35
35
35
35
34
34
34
34
34
34
34
34
34
34
33
33
33
33
33
33
33
33
33
33
32
32
32
32
32
32
32
32
32
32
31
31
31
31
31
31
31
31
31
31
30
30
30
30
30
30
30
30
30
30
29
29
29
29
29
29
29
29
29
29
28
28
28
28
28
28
28
28
28
28
27
27
27
27
27
27
27
27
27
27
26
26
26
26
26
26
26
26
26
26
25
25
25
25
25
25
25
25
25
25
24
24
24
24
24
24
24
24
24
24
23
23
23
23
23
23
23
23
23
23
22
22
22
22
22
22
22
22
22
22
Contractors - Engineers - Designers
Electrical - Data/Voice Networks - Fire Alarm
Temperature Control - Structured Cable - Building
Automation - Energy Management Solutions
Audio/Visual - Security - Surveillance
Communications
WS-X6724-SFP
24 PORT GIGABIT ETHERNET SFP
1
COMMUNICATIONS DIVISION
STATUS
Catalyst
4510R-E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
WS-X6724-SFP
24 PORT GIGABIT ETHERNET SFP
5055B Corbin Dr. Bedford Hts. Ohio 44128
2
STATUS
Office (216) 587-9510 Fax (216) 395-5980
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
WS-X6724-SFP
24 PORT GIGABIT ETHERNET SFP
3
STATUS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
TR 1-12 (Area 1A)
WS-X6724-SFP
24 PORT GIGABIT ETHERNET SFP
Switch 1 – 24 Port 10/100/1000 POE
4
STATUS
1
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
SUPERVISOR
5
2
Switch 2 – 24 Port 10/100/1000 POE
SUPERVISOR
6
WS-X6724-SFP
24 PORT GIGABIT ETHERNET SFP
Switch 3 – 48 Port 10/100/1000
7
STATUS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
WS-X6724-SFP
24 PORT GIGABIT ETHERNET SFP
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Switch 4 – 48 Port 10/100/1000
9
21
21
21
21
21
21
21
21
21
21
20
20
20
20
20
20
20
20
20
20
19
19
19
19
19
19
19
19
19
19
18
18
18
18
18
18
18
18
18
18
17
17
17
17
17
17
17
17
17
17
16
16
16
16
16
16
16
16
16
16
15
15
15
15
15
15
15
15
15
15
14
14
14
14
14
14
14
13
13
13
13
13
13
12
12
12
12
12
12
12
11
11
11
11
11
11
11
10
10
10
10
10
10
10
9
9
9
9
9
9
9
8
8
8
8
8
8
10
WS-X 6724-S FP
24 PORT GIGABIT ETHERNE T SFP
1
STATUS
Catalyst
4510R-E
Wireless Controller – Cisco AIR-CT5508-100-K9
14
14
14
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
WS-X 6724-S FP
24 PORT GIGABIT ETHERNE T SFP
2
STATUS
1
2
3
WS-X 6724-S FP
24 P ORT GIGAB IT ETHERNET SFP
13
13
13
13
3
STATUS
1
2
3
WS-X 6724-S FP
24 P ORT GIGAB IT ETHERNET SFP
12
12
12
11
11
11
10
10
10
9
9
9
4
STATUS
1
6
SUPERVISOR
Wireless Controller System – Dell R-320 with Cisco WCS-PLUS-100
3
SUP ERVISOR
5
2
WS-X 6724-S FP
24 P ORT GIGAB IT ETHERNET SFP
7
STATUS
1
8
8
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
8
8
WS-X 6724-S FP
24 P ORT GIGAB IT ETHERNET SFP
8
STATUS
Mobility Services Engine/Location Tracking – Cisco AIR-MSE-3310-K9
7
7
7
6
6
6
5
5
5
4
4
4
1
2
3
7
7
7
7
7
7
7
6
6
6
6
6
6
6
5
5
5
5
5
5
5
4
4
4
4
4
4
4
3
3
3
3
3
3
2
2
2
2
2
2
2
1
1
1
1
1
1
1
9
10
AVR Trim
Smart-UPS
I
Test
O n Line
2 2 0 0
AVR Boost
3
3
3
2
2
2
1
1
Overload
On B attery
O
Load
HIGH SCHOOL
1
SHELBY
STATUS
CITY SCHOOLS
8
Battery
Charge
Replace B attery
3
w w w . a p cc. c om
Switch 1 – 24 Port 10/100/1000 POE
AVR Trim
Smart-UPS
I
Test
O n Line
2 2 0 0
Overload
AVR Trim
Smart-UPS
On B attery
O
Load
AVR Boost
I
Test
O n Line
2 2 0 0
Battery
Charge
AVR Boost
w w w . a p cc. c om
Overload
AVR Trim
Smart-UPS
On B attery
O
Load
Replace B attery
1
I
Test
O n Line
2 2 0 0
Battery
Charge
AVR Boost
w w w . a p cc. c om
Overload
On B attery
O
Load
Replace B attery
Battery
Charge
Replace B attery
w w w . a p cc. c om
Switch 2 – 24 Port 10/100/1000 POE
Switch 3 – 48 Port 10/100/1000 POE
Switch 4 – 48 Port 10/100/1000
Switch 5 – 48 Port 10/100/1000
Switch 6 – 48 Port 10/100/1000
Switch 7 – 48 Port 10/100/1000
Switch 8 – 48 Port 10/100/1000
Switch 9 – 48 Port 10/100/1000
*All switches are 10/100/1000 capable.
*Uplinks are currently shown with 1 uplink
per 24 ports
*Current switch layout is based on
preliminary bid information and might
change with final cabling panel punches
from Technology Infrastructure
Contractor.
Final IP/VLAN/labeling plan to be
coordinated with district IT.
PLEASE REFER TO SUBMITTAL TABLE
OF CONTENTS AND DATA SHEETS
FOR FULL PART NUMBERS
RACK 2
RACK 3
RACK 4
RACK 2
RACK 2
(Rack provided by others)
SW04: Cisco 48 Port 10/100/1000
SW05: Cisco 48 Port 10/100/1000
SW06: Cisco 48 Port 10/100/1000
SW07: Cisco 48 Port 10/100/1000
SW08: Cisco 48 Port 10/100/1000
SW09: Cisco 48 Port 10/100/1000
SW10: Cisco 48 Port 10/100/1000
SW11: Cisco 48 Port 10/100/1000
SW12: Cisco 48 Port 10/100/1000
UPS SMT3000RM2U
(Rack provided by others)
SW01: Cisco 24 Port 10/100/1000 POE
SW02: Cisco 24 Port 10/100/1000 POE
SW03: Cisco 48 Port 10/100/1000 POE
UPS Battery Pack SMX120RMBP2U
UPS SMX3000RMLV2U
(Rack provided by others)
Cisco Wireless Controller
Dell/Cisco Wireless Control System
Cisco Mobility Services Engine
Cisco Integrated Services Router
SW01: Cisco 24 Port 10/100/1000 POE
SW02: Cisco 24 Port 10/100/1000 POE
SW03: Cisco 48 Port 10/100/1000
UPS SMT2200RM2U
SW01: Cisco 24 Port 10/100/1000 POE
SW02: Cisco 24 Port 10/100/1000 POE
SW03: Cisco 48 Port 10/100/1000
SW04: Cisco 48 Port 10/100/1000
UPS SMT2200RM2U
Input Receptacle Needed: 5-20
Input Receptacle Needed: 5-20
Input Receptacle Needed: L5-30
OWNER:
SHELBY CITY
SCHOOL DISTRICT
Input Receptacle Needed: L5-30
SHELBY, OHIO
(All closet buildout material provided by others is not shown unless indicated)
SCALE:
NTS
TYPICAL AP INSTALLATION
DRAWN
BY:
ZENITH SYSTEMS, LLC
COMMUNICATIONS DIVISION
All Wireless Access Points will be ceiling mounted.
The bracket on the back of the access point clips directly to
the ceiling grid.
Switch 10 – 48 Port 10/100/1000
Switch 11 – 48 Port 10/100/1000
Switch 12 – 48 Port 10/100/1000
NETWORK SCHEMATIC
= COPPER
Spec Sec(s): 27 21 00
= MM FIBER, 1 GIG UPLINK
05/01/2013
= MM FIBER, 10 GIG UPLINK
N-01