GSW-0509/GSW-0809 5/8-Port Gigabit Switch

GSW-0509/ GSW-0809
5/8-Port Gigabit Switch
V1. 0_20150422
1
Table Of Contents
1. INTRODUCTION ......................................................... 3
1.1
Product Briefs ....................................................................................................... 3
1.2
Product Features.................................................................................................... 3
1.3
Hardware Introduction .......................................................................................... 4
2. CONNECTING THE SWITCH .................................... 6
2.1
Package Contents .................................................................................................. 6
2.2
Before You Connect to the Network ..................................................................... 6
3. Connecting the switch ................................................... 7
3.1
Switch to End Node or Server .............................................................................. 7
4. Appendix ....................................................................... 8
4.1
Technical Specifications ....................................................................................... 8
4.2
RJ-45 PIN SPECIFICATION ............................................................................... 9
2
1. INTRODUCTION
1.1 Product Briefs
The switch is a un-management layer 2 10/100/1000Mbps switch; it provide dedicated 10,
100 or 1000 Mbps Ethernet bandwidth on each port. The ports will automatically detect the
speed, duplex and MDI/MDIX status of the device it is connecting to, and adjust these
settings accordingly. The Switch ports can be used to network computers, printers, servers,
routers, other switches or any device equipped with an Ethernet port. For best performance,
use Category 5 or better Ethernet cabling.
This stand-alone Switch is very easy to set up, there is no network management required.
Just power on the Switch and connect the cables. Keep in mind however that the standard
rules of Ethernet regarding cable length apply to this and all Ethernet devices. The length of
an Ethernet cable from one device to another cannot exceed 100 meters (or 300 feet).
1.2 Product Features
The Switches do not require any management. All Switches are designed for easy
installation, flexibility and high performance. Connect devices to the Switch as the scale and
volume of network traffic increases.

5/8 10/100/1000Mbps Ethernet ports

Auto-Negotiation for 10/100/1000Mbps and duplex mode

Auto-MDI/MDIX for each port

Supports Full/Half-duplex transfer mode for 10 and 100Mbps

Supports Full-duplex transfer mode for 1000Mbps

Full wire speed reception and transmission

Store-and-Forward Switching method

Supports 8K absolute MAC addresses

5-Port Switch Supports 125KB RAM for data buffering

8-Port Switch Supports 125KB RAM for data buffering

IEEE 802.3x flow control for Full-duplex

Back pressure flow control for Half-duplex
3
Gigabit Ethernet is an extension of IEEE 802.3 Ethernet utilizing the same packet structure,
format, and support for CSMA/CD protocol, full duplex, flow control, and management
objects, but with a tenfold increase in theoretical throughput over 100-Mbps Fast Ethernet
and a hundredfold increase over 10-Mbps Ethernet. Since it is compatible with all 10-Mbps
and 100-Mbps Ethernet environments, Gigabit Ethernet provides a straightforward upgrade
without wasting a company’s existing investment in hardware, software and trained
personnel.
The increased speed and extra bandwidth offered by Gigabit Ethernet is essential to coping
with the network bottlenecks that frequently develop as computers and their bus speeds get
faster and more users use applications that generate more traffic. Upgrading key components,
such as your backbone and servers to Gigabit Ethernet can greatly improve network response
times as well as significantly speed up the traffic between your subnets.
1.3 Hardware Introduction
1.3.1
Product Appearance
1.Front Panel
The figure below shows the front panel of the Switch.
5-Port Gigabit Switch Front Panel
8-Port Gigabit Switch Front Panel
4
2.Rear Panel
The figure below shows the rear panel of the Switch. There is a AC inlet in the 5/8-Port
switch rear panel.
5-Port Gigabit Switch Rear Panel
8-Port Gigabit Switch Rear Panel
Auto MDI/MDI-X Ports:
All ports support automatic MDI/MDI-X crossover detection. The AutoMDI/MDI-X function
makes it simple to connect to the switch—just plug either a Crossover or Straight-Through
CAT5 cable into any port.
AC inlet
Power is supplied through external AC power. The input AC voltage is 100~240V.
1.3.2 LED Indicators
Table 1-3 Ethernet Switch LED Indicators
LED
Power
Indicator
Speed
Panel
signature
Power
1000M
Status
Description
Green ON
Switch is powered ON
OFF
Switch is powered OFF
Green ON
1000Mbit/s
5
Indicator
Status
Link/Act
Indicator
Loop
OFF
1000M no link
Green ON
Link
Green Blinking
Activity
OFF
No link path
Red ON
Network has loops
OFF
Network normal
2. CONNECTING THE SWITCH
2.1 Package Contents
Open the shipping carton of the Switch and carefully unpack its contents.
The carton should contain the following items:

One 5/8 Port 10/100/1000BASE-T Gigabit Ethernet Switch

Four rubber feet with adhesive backing

One power Cord

CD-ROM with product documentation
If any item is found missing or damaged, please contact your local reseller for replacement.
2.2 Before You Connect to the Network
The site where you install the Switch may greatly affect its performance. Please follow
these guidelines for setting up the Switch.

Install the Switch on a sturdy, level surface that can support at least 3 kg (6.6 lbs) of
weight. Do not place heavy objects on the Switch.

The power outlet should be within 1.82 meters (6 feet) of the Switch.

Visually inspect the power cord and see that it is fully secured to the AC power port.

Make sure that there is adequate space for proper heat dissipation from and adequate
ventilation around the Switch. Leave at least 10 cm (4 inches) of space at the front and
rear of the Switch for ventilation.

Install the Switch in a fairly cool and dry place for the acceptable temperature and
humidity operating ranges.

Install the Switch in a site free from strong electromagnetic field generators (such as
motors), vibration, dust, and direct exposure to sunlight.

When installing the Switch on a level surface, attach the rubber feet to the bottom of the
device. The rubber feet cushion the Switch, protect the casing from scratches and prevent
it from scratching other surfaces.
6
3. Connecting the switch
Cable Quality
For all connections to the Switch, use these rules to determine the Cable quality.

For connections to 10BASE-T and 100BASE-TX devices, use Category 5 or 5e
UTP/STP cable.

For connections to 1000BASE-T and 100BASE-TX devices, use Category 5e or better
UTP/STP cable. All 1000BASE-T connections operate in full duplex mode.
NOTE: UTP (Unshielded Twisted Pair) Ethernet cabling is adequate for
most small office environments. More expensive STP (Shielded Twisted
Pair) can also be used, but is generally only needed where there will be
risk of strong Electromagnetic of Radio Frequency Interference.
3.1 Switch to End Node or Server
End nodes include PCs outfitted with a 10, 100 or 1000 Mbps RJ-45 Ethernet/Fast Ethernet
Network Interface Card (NIC) and Ethernet ready routers. Use standard Ethernet cable to
connect the Switch to end nodes. Switch ports will automatically adjust to the hardware
characteristics (MDI-II/MDI-X, speed, duplex) of the device to which it is connected. Switch
connected to an end node
Reference picture
7
4. Appendix
4.1 Technical Specifications
Table 4-1 Ethernet Switch General Features
General
IEEE 802.3ab 1000BASE-T
Standards:
IEEE 802.3u 100BASE-TX
IEEE 802.3 10BASE-T
IEEE 802.3x Flow Control
Protocol:
CSMA/CD
Data Transfer Rate:
Ethernet:
10Mbps (Half-duplex)
20Mbps (Full-duplex)
Fast Ethernet:
100Mbps(Half-duplex)
200Mbps(Full-duplex)
Gigabit Ethernet:
2000Mbps (Full-duplex)
Topology:
Star
Network Cables:
Ethernet:
2-pair UTP Cat. 3,4,5, Unshield Twisted Pair (UTP )Cable
Fast Ethernet:
2-pair UTP Cat. 5, Unshield Twisted Pair (UTP )Cable
Gigabit Ethernet:
4-pair UTP Cat. 5, Unshield Twisted Pair (UTP )Cable
Number of Ports:
5/8
Table 4-2 Ethernet Switch Physical and Environmental Features
Physical and Environmental
AC Inputs(For 5/8-Port):
Power Consumption
100~240VAC; 3.3V/2A
5-Port: 6.6 watts maximum
8-Port: 6.6 watts maximum
Operating Temperature
0 C ~ 45℃(32F ~ 113F )
Storage Temperature:
-10C ~ 70C (14F ~ 158F)
Humidity:
5% ~ 95% RH, non-condensing
Dimensions:
5/8-Port: 190mm x 120mm x 35mm
8
EMI
FCC Class B, CE Mark Class B
Safety:
CSA International
Table 4-3 Ethernet Switch Performance Features
Performance
Transmission Method:
Store-and-forward
5-Port : 125KB
RAM Buffer:
8-Port : 125KB
Filtering Address Table:
8K MAC address per device
Packet Filtering/ Forwarding Rate:
Full wire speed
MAC Address Learning:
Self-learning, auto-aging
4.2 RJ-45 PIN SPECIFICATION
The following diagram and tables show the standard RJ-45 receptacle/connector and their pin
assignments.
RJ-45 Connector pin assignment
Contact
Media Direct Interface Signal
Contact
Media Direct Interface Signal
1
TX_D1+
5
BI_D3-
2
TX_D1-
6
RX_D2-
3
RX_D2+
7
BI_D4+
4
BI_D3+
8
BI_D4-
Standard RJ-45 receptacle/connector
9