eMyWay
SATELLITE NAVIGATION SYSTEM
MULTIMEDIA BLUETOOTH
TELEPHONE AUDIO SYSTEM
CONTENTS
The system is protected in such a way that it will only
operate in your vehicle.
For safety reasons, the driver must only carry out
operations which require prolonged attention while the
vehicle is stationary.
When the engine is switched off and to prevent
discharging of the battery, the system switches off
following the activation of the energy economy mode.
01 First steps - Control panel
02 Steering mounted controls
03 General operation
04 Navigation - Guidance
05 Traffic information
06 Using the telephone
07 Radio
08 Music media players
09 Audio settings
10 Configuration
11 Screen menu map
Frequently asked questions
p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
p.
236
238
239
241
254
257
267
271
277
278
279
283
235
01 FIRST STEPS
MODE button: Selection of the
type of permanent display.
Long press: black screen
(DARK).
Access to the
"Navigation - guidance"
menu and display the
recent destinations.
Open the "Traffic
information" menu
and display the
current traffic alerts.
Continuous press:
reinitialisation of the system.
Short press: select pre-set
radio station.
Long press: pre-set the
current station.
Rotary control knob:
Short press without the engine running: on / off.
Short press with the engine running: audio
source off / restore.
Rotation: volume adjustment (each source
is independent, including TA messages and
navigation instructions).
236
Open the
"Configuration" menu.
Long press: access
to the GPS coverage
and the navigation
demonstration mode.
Open the
"Telephone" menu
and display the list of
recent calls or accept
an incoming call.
01 FIRST STEPS
Select:
the previous/next line in a list or menu.
the previous / next media folder.
step by step selection of the previous/next radio frequency.
the previous / next MP3 folder.
Move up/down, in "Move the map" mode.
Select:
the next lower / higher radio frequency automatically.
the previous / next CD track, MP3 track or media.
the left / right of the screen when a menu is displayed.
Move left / right in "Move the map" mode.
Abandon the current
operation, up one level in
the menu.
Long press: return to the
permanent display.
Selection and OK confirmation knob:
Selection of an item on the screen or in a list or a
menu, then confirmation with a short press.
Other than for menus and lists, a short press
displays a contextual menu depending on the
current screen.
Rotation with map displayed: zoom the map scale
in and out.
Access to the "MUSIC" menu, and display of
the CD/MP3/Apple® tracks and folders.
Long press: display the audio settings screen
for the "MEDIA (CD/USB/iPod/Streaming/
AUX)" sources.
Access to the "RADIO" menu and display
the list of stations received.
Long press: display the audio settings
screen for the radio tuner source.
Long press: open the "Audio settings" menu: music ambience, bass, treble, loudness, left/
right balance, front/rear fader, automatic volume adjustment.
237
02 STEERING MOUNTED CONTROLS
-
Change the audio source.
Long press: mute.
-
Volume increase.
-
Volume decrease.
-
Radio: display the list of stations.
Media: display the list of tracks.
-
Rotation
Radio -automatic selection of next /
previous frequency.
Media: previous / next track.
Press then rotation: access to
6 preset stations.
-
238
-
TEL button:
Access to the telephone menu:
Call list / Contacts / Hands-free
mode / Answer / Hang up.
Accept an incoming call.
Long press: reject an incoming call
or end the current call.
-
Move in the menus.
Zoom the map in and out
Press: confirmation
-
Abandon the current operation.
03 GENERAL OPERATION
Press the MODE button several times in succession for access to the following displays:
"TRIP COMPUTER"
(Permanent display)
"FULL SCREEN MAP"
"RADIO"
"MAP IN WINDOW"
(If navigation guidance in
progress)
SETUP: PARAMETERS date and time, display
configuration, sound, vehicle settings.
For cleaning the screen, the use of a soft, non-abrasive cloth
(spectacles cloth) is recommended, with no additional product.
Changing the audio source:
RADIO: RADIO broadcasts.
MUSIC: playing MUSIC.
For the details of the menus, refer to the "Screen menu map"
section.
239
03 GENERAL OPERATION
Display according to context
A press on the knob gives access
to short-cut menus according to the
display in the screen.
RADIO:
1
Activate / Deactivate TA
1
Activate / Deactivate RDS
1
Change waveband
2
2
1
FM
AM
TA
1
DTMF ring tones
1
Hang up
MUSIC MEDIA PLAYERS,
CD or USB (according to
media):
Play modes:
1
Select destination
1
2
2
2
1
1
1
Move the map
Random
Repetition
2
2
2
TELEPHONE (call in
progress):
1
Private mode
1
Put call on hold
240
FULL SCREEN MAP OR
IN A NEW WINDOW:
1
Stop / Restore guidance
GPS coordinates
Divert route
Normal
Random on all media
Directory
1
2
1
Enter an address
2
1
Info. on location
Select as destination
Select as stage
Save this place (contacts)
Quit map mode
Guidance criteria
04 NAVIGATION - GUIDANCE
Access to the "Navigation" menu
To make full use of all of the
functions of your navigation
system, update the mapping
regularly. Contact a
CITROËN dealer or order
your mapping update at
http://citroen.navigation.com
"Navigation - guidance"
Press NAV.
List of recent destinations.
A short press on the end of the
lighting control stalk repeats
the last navigation message.
"Select destination"
"Journey leg and route"
"Guidance options"
"Map management"
"Stop / Restore guidance"
Go from the list to the menu (left/right).
To delete the list of recent destinations, select "Guidance
options" in the navigation menu then select "Delete last
destinations" and confirm. Select "Yes" then confirm.
Deleting just one destination is not possible.
or
241
04 NAVIGATION - GUIDANCE
Selecting a destination
Towards a new destination
Press NAV to display the
"Navigation - guidance" menu.
Select "Select destination" and
confirm, then select "Enter an address"
and confirm.
Select the "Country" function then
confirm.
Select the "Town" or "Post code"
function then confirm.
Select the letters in the name of the
town or the characters in a post code
one at a time, confirming each one with
the knob.
242
Selection the town from the list offered,
then confirm
A pre-set list (by entering the first few
letters) of the towns in the country
selected can be accessed directly by
selecting and confirming "List" in the
screen.
If possible, enter the "Road" and "N°/X"
information in the same way.
Select "Archive" to save the address entered in a contact file.
The system allows up to 400 contact files to be recorded.
Confirm "OK" to start guidance.
Select the guidance criteria: "Fastest
route", "Shortest route" or optimised
"Distance/Time", then select the
desired restriction criteria: "With tolls",
"With Ferry", or "Traffic info" then
confirm "OK".
04 NAVIGATION - GUIDANCE
Towards a recent destination
Press NAV to display the
"Navigation - guidance" menu.
Select the desired destination and
confirm to start guidance.
Towards a contact in the contacts directory
Navigation towards a contact is only possible if it has an address
entered in the audio navigation system.
Press NAV to display the
"Navigation - guidance" menu.
Delete recent destinations
Press NAV to display the
"Navigation - guidance" menu.
Select "Options" and confirm and then
"Delete recent destinations" and
confirm.
Select "Select destination" and
confirm, then select "Directory" and
confirm.
Selection the desired destination from
your contacts and confirm "OK" to start
the guidance.
243
04 NAVIGATION - GUIDANCE
Towards GPS coordinates
Press NAV to display the
"Navigation - guidance" menu.
Towards a point on the map
With the map displayed, press OK to
display the contextual menu. Select
"Move the map" and confirm.
Select "Select destination" and
confirm, then select "GPS coordinates"
and confirm.
Move the cursor using the control to
identify the desired destination.
Enter the GPS coordinates and confirm
"OK" to start the guidance.
Press OK to display the contextual
menu for "Move the map" mode.
Select "Select as destination" or
"Select as stage" and confirm.
244
04 NAVIGATION - GUIDANCE
Towards points of interest (POI)
Press NAV to display the
"Navigation - guidance" menu.
Select the "Enter an address" function
and confirm, then select Select
destination and confirm.
To select a POI close to your current
location, select "POI" and confirm, then
select "Around the current place" and
confirm.
To select a POI as a stage on the route,
select "POI" and confirm, then select "On
the route" and confirm.
To select a POI as a destination, first
enter the country and town (see "Towards
a new destination"), select "POI" and
confirm, finally select "Near" and confirm.
The points of interest (POI) indicate all of the service locations in the vicinity
(hotels, various businesses, airports…).
Select "Search by Name" to search for POIs by name and not by
proximity.
Search for POIs in the categories
suggested in the following pages.
Select the POI and confirm "OK" to start
the guidance.
245
04 NAVIGATION - GUIDANCE
This icon appears when several POIs are grouped
together in the same area. Zooming in on this icon
shows details of the POIs.
List of principal points of interest (POI)
Service station
Airport
Cinema
Garage
Railway station
Theme parks
CITROËN
Bus station
Hospital, Chemist, Vet
Covered car park
Port
Police station
Car park
Industrial estate
School
Rest area
Supermarket
Town hall
Hotel
Vending machine
Post office
Restaurant
Sports complex, sports centre,
sports ground
Museum, Culture, Theatre,
Historic monument
Cafeteria
Swimming pool
Tourist information, Tourist
attraction
Bed and breakfast
Winter sports resort
Risk areas / Danger areas*
An annual mapping update allows new points of interest to be presented to you.
You can also update the Risk areas / Danger areas every month.
The detailed procedure is available on:
http://citroen.navigation.com.
246
* According to availability in the country.
04 NAVIGATION - GUIDANCE
Settings for risk area / danger area alerts
Press NAV to display the "Navigation guidance" menu.
These functions are only available if risk areas have been
downloaded and installed on the system.
The detailed procedure for updating risk area POIs can be found at
http://citroen.navigation.com.
Select "Guidance options" and confirm,
then select "Set parameters for risk
areas" and confirm.
Select:
"Visual alert"
"Audible alert"
"Alert only in guidance"
"Overspeed alarm only".
The choice of time of notification defines
how long in advance that Risk area
warnings are given.
Select "OK" to confirm the screen.
247
04 NAVIGATION - GUIDANCE
Adding a stage
Press NAV to display the
"Navigation - guidance" menu.
Organising stages
To organise stages, carry out operations 1
to 2 again, then select "Order/delete
journey legs" and confirm.
Select "Journey leg and route" then
confirm.
Select the stage that you want to move
in the order.
Select "Add a stage" then confirm.
The address of the stage is entered as
a destination, by "Enter an address",
a contact in "Directory", or "Previous
destinations".
Select and confirm to save the
modifications.
Select "Delete" to delete the stage.
Select "Close to" a route passing
close to the stage or "Strict" for a route
passing through the stage.
Confirm "OK" to start the guidance, and
give a general indication of the guidance
route.
248
04 NAVIGATION - GUIDANCE
Route options
Calculation criteria
Press NAV to display the
"Navigation - guidance" menu.
Select "Define calculation criteria" and
confirm.
This function allows modification of:
the guidance criteria: ("Fastest
route", "Shortest route",
"Distance/Time"),
the exclusion criteria: ("With tolls"
or "With Ferry"),
traffic avoidance: ("Traffic info").
If traffic avoidance (Traffic info) is selected, the system suggests
an alternative route if there is a delay on the guidance route.
Select "Guidance options" and confirm.
Select "OK" and confirm to save the
modifications.
249
04 NAVIGATION - GUIDANCE
Map management
Selecting the points of interest displayed on the map
Press NAV to display the
"Navigation - guidance" menu.
Select "Map management" and confirm.
Select "Map details" and confirm.
250
Select from the various categories the
ones that you want to display on the
screen.
Select "Default" to have only "Filling stations, garages" and
"Risk areas" appear on the map (if installed in the system).
Select "OK" then confirm and select
"OK" again then confirm to save the
modifications.
04 NAVIGATION - GUIDANCE
Map orientation
Press NAV to display the
"Navigation - guidance" menu.
Select:
"Vehicle direction" to have the map
follow the direction of travel,
"North direction" to keep the map
always North up,
"Perspective view" to display a
perspective view.
Select "Map management" and confirm.
The colour of the map, different from the day and night mode, is
configured in the "SETUP" menu.
Select "Map orientation" and confirm.
Street names are visible on the map from the 100 m scale.
251
04 NAVIGATION - GUIDANCE
Navigation voice synthesis
Adjusting the volume / Deactivation
The volume of messages can be adjusted during the transmission
of the message using the volume adjustment control.
Select the volume graph and confirm.
The volume setting of guidance messages is also accessible via
the "SETUP" / "Voice synthesis" menu.
Press NAV to display the
"Navigation - guidance" menu.
Select "Guidance options" and confirm.
Select "Set speech synthesis" and
confirm.
252
Adjust the volume to the desired level
and confirm.
Select "Deactivate" to deactivate voice messages.
Select "OK" and press the dial to
confirm.
04 NAVIGATION - GUIDANCE
Male voice / Female voice
Press SETUP to display the
configuration menu.
Select "Voice synthesis" and confirm.
Select "Select male voice" or "Select
female voice" then confirm "Yes" to
activate a male or female voice. The
system restarts.
253
05 TRAFFIC INFORMATION
Access to the "Traffic information" menu
"Traffic information"
Press "TRAFFIC".
List of TMC messages in order
of distance from the vehicle.
"Geographic filter"
"Select TMC station"
(automatic, manual)
"Display/Do not display
messages"
Go from the list to the menu (left/right).
or
254
05 TRAFFIC INFORMATION
Configure the filtering and display of TMC messages
TMC (Traffic Message Channel) messages contain information on traffic and weather conditions, received in real time and transmitted to the
driver in the form of audible announcements and symbols on the navigation map.
The navigation system can then suggest an alternative route to avoid a traffic problem.
Press the TRAFFIC button to display the
"Traffic information" menu.
The system offers a choice of:
"Retain all the messages",
or
"Retain the messages"
● "Around the vehicle", (confirm
the mileage to modify and select
the distance),
● "On the route".
Select the "Geographic filter" function
and confirm.
Confirm "OK" to save the modifications.
We recommend:
a filter on the route and
a filter around the vehicle of:
- 12 miles (20 km) in urban areas,
- 30 miles (50 km) on motorways.
255
05 TRAFFIC INFORMATION
Principal TMC symbols
Receiving TA messages
Black and blue triangle: general information, for example:
The TA (Traffic Announcement) function gives priority to TA alert
messages. To operate, this function needs good reception of a
radio station transmitting this type of message. When a traffic report
is transmitted, the current audio source (Radio, CD, USB, …) is
interrupted automatically to play the TA message. Normal playback
of the audio source resumes at the end of the transmission of the
message.
Weather reports
Traffic reports
Wind
Fog
Parking
Snow / ice
Press RADIO to display the "FM / AM
band" menu.
Red and yellow triangle: traffic information, for example:
256
Modified signage
Narrow carriageway
Slippery surface
Accident
Delay
Roadworks
Risk of explosion
Road closed
Demonstration
Danger
No entry
Traffic jam
Select "Guidance options" then
confirm.
Activate or deactivate "TA" then confirm.
The volume setting for TA messages can be adjusted only during the
transmission of this type of alert.
Activate or deactivate the function at any time by pressing
the button.
During a message, press the button to interrupt it.
06 USING THE TELEPHONE
Access to the "TELEPHONE" menu
In the top bar of the permanent
display
"Telephone"
No telephone connected.
Press PHONE.
List of recent calls sent and
received with the telephone
connected to the system.
"Dial "
"Directory of contacts"
"Contacts management"
"Phone functions"
"Bluetooth functions"
"Hang up"
Telephone connected.
Incoming call.
Outgoing call.
Synchronisation
of address book in
progress.
Telephone call in
progress.
To make a call, select a number in the list and confirm "OK"
to start the call.
Connecting a different telephone deletes the list of
recent calls.
Go from the list to the menu (left/right).
or
257
06 USING THE TELEPHONE
Pairing a Bluetooth telephone
First connection
You can check the compatibility of your telephone at
www.citroen.co.uk (services).
Quick procedure from the telephone
For reasons of safety and because they require prolonged attention
on the part of the driver, the operations for pairing the Bluetooth
mobile telephone to the hands-free system of the audio unit must be
carried out with the vehicle stationary.
Procedure from the system
Activate the telephone's Bluetooth function
and ensure that it is "visible to all" (telephone
configuration).
In the Bluetooth menu of your telephone, select
the name of the system from the list of devices
detected.
Press this button.
Enter a minimum 4 figure code in the telephone and
confirm.
Enter the same code in the system,
select "OK" and confirm.
258
Select "Bluetooth functions" and
confirm.
Select "Peripherals search" and
confirm.
The list of peripheral devices detected
is displayed. Wait until the "Connect"
button is available.
06 USING THE TELEPHONE
The services available depend on the network, the SIM card and the compatibility of the Bluetooth telephone used. Check the telephone
manual and with your network provider for details of the services available to you.
Select the name of the desired
peripheral from the list of devices
detected then confirm
Select "Connect" and confirm.
The system offers to connect the
telephone:
in "Hands-free mode" (telephone
only),
in "Audio" mode (streaming: playing
music files on the telephone),
or "All" (for selection of both
modes).
Select "OK" and confirm.
The "Hands-free mode" should be used in preference if
"Streaming" is not desired.
The ability of the system to connect in only one mode depends on
the telephone. The two modes may both connect by default.
Enter a minimum 4 figure code in the telephone
and confirm.
Enter the same code in the system,
select "OK" and confirm.
Then accept automatic connection on the telephone to allow the
telephone to reconnect automatically every time the vehicle is
started.
Depending on the type of telephone, the system will ask you to
accept or not the transfer of your contacts.
On return to the vehicle, the last telephone connected
automatically reconnects, within around 30 seconds after
switching on the ignition (Bluetooth activated and visible).
To modify the automatic connection mode, remove the pairing
and pair the telephone again with the desired mode.
259
06 USING THE TELEPHONE
Directory configuration / Synchronisation with the telephone
Press PHONE then select "Contacts
management" and confirm.
Select "New contact" to enter a new
contact.
Select "Sort by Name/First name" to
choose the order in which they appear.
Select "Delete all contacts" to delete
the contacts saved in the system.
260
Select "Import all the entries" to import
all the contacts in the telephone and
save them in the system.
Once imported, a contact remains visible
whatever telephone is connected.
Select "Synchronization options":
No synchronization: only the
contacts saved in the system
(always present).
Display telephone contacts: only the
contacts saved in the telephone.
Display SIM card contacts: only the
contacts saved on the SIM card.
Display all phone contacts:
contacts on the SIM card and in the
telephone.
Select "Contact mem. status" to see the
number of contacts saved in the system
or imported, and the free memory.
06 USING THE TELEPHONE
Editing, importing or deleting a contact
Press PHONE then select "Directory of
contacts" and confirm.
It is not possible to modify or delete contacts in the telephone or the
SIM card via the Bluetooth connection.
Select the desired contact and confirm.
Once the contact has been imported, the Bluetooth symbol
disappears, replaced by the telephone symbol which shows that the
contact has been saved in the system.
Select "Open" to view a contact on the
telephone or modify a contact saved in
the system.
In the "Directory of contacts" menu, the import and deletion of
contacts is done one by one.
Select "Import" to copy a contact from
the telephone to the system.
Select OK or press the back button to exit
this menu.
Select "Delete" to delete a contact
recorded in the system.
261
06 USING THE TELEPHONE
Making a call
Use of the telephone is not recommended while driving. We
recommended that you park safely or make use of the steering
mounted controls.
Calling a new number
Calling a contact
Press TEL or twice on PHONE.
Press PHONE twice.
Select "Directory of contacts" then
confirm.
Select "Dial" then confirm.
Select the desired contact and confirm.
If access was via the PHONE button,
select "Call" and confirm.
Dial the telephone number using the
virtual keypad selecting each number
in turn.
Confirm "OK" to make the call.
262
Select the number and confirm to start
the call.
06 USING THE TELEPHONE
Ending a call
Calling a recently entered number
Press TEL, select "Call list" and
confirm,
Press PHONE then select "OK" to end
the call.
or
press PHONE to display the calls log.
Or make a long press on TEL at the
steering mounted controls.
Or make two short presses on TEL at
the steering mounted controls.
Select the desired number and confirm.
To erase the calls log, press PHONE twice, select "Phone
functions" and confirm then select "Delete calls log" and
confirm.
It is always possible to start a call directly from the telephone;
park the vehicle as a safety measure.
Or press the MODE button, as many
times as necessary, until the telephone
screen is displayed.
Press "OK" to display the contextual
menu then select "Hang up" and
confirm.
263
06 USING THE TELEPHONE
Receiving a call
An incoming call is announced by a ring and a superimposed display
on the screen.
"Yes" to accept the call is selected by
default.
Press "OK" to accept the call.
Select "No" and confirm to reject the
call.
A short press on TEL accepts an
incoming call.
A long press on TEL rejects an incoming
call.
264
06 USING THE TELEPHONE
Options during a call*
During a call, press the MODE button
several times to select display of the
telephone screen, then press "OK" to
open the contextual menu.
Select "DTMF ring tones" to use the
numerical keypad, so as to navigate
through the menu of an interactive vocal
server.
Select "Hang up" to end the call.
Or make a short press on this button.
Select "Private mode" and confirm to
take the call on the handset.
Or select "Hands-free mode" and
confirm to take the call via the vehicle's
speakers.
it is possible to hold a 3-way conference
call by making 2 calls in succession*.
Select "Conference mode call" in the
contextual menu accessible using this
button.
Select "Put call on hold" and confirm to
put the current call on hold.
Or select "Resume the call" and
confirm to resume the call on hold.
* Depending on the compatibility of the phone and your service plan.
265
06 USING THE TELEPHONE
Managing paired telephones
Changing the ringtone
Press PHONE twice.
Press PHONE twice.
Select "Phone functions" and confirm.
Select "Bluetooth functions".
Select "Ring options" and confirm.
Select "List of the paired peripherals"
and confirm.
It is possible to:
"Connect" or "Disconnect" the
selected telephone,
delete the pairing of the selected
telephone.
It is also possible to select all pairings.
266
You can adjust the volume and the type
of ringtone.
Select "OK" and confirm to save the
changes.
07 RADIO
Access to the "RADIO" menu
"FM / AM band / DAB"
Press RADIO.
Alphabetical list of stations
received.
A long press on LIST refreshes
the list of stations received.
"Change waveband" ("AM / FM /
DAB")
"Guidance options" ("TA, RDS,
FM alternative frequencies /
DAB")
"Audio settings" (see this section)
"Update radio list"
Go from the list to the menu (left/right).
Press  or  or use the rotary control to select the
previous or next station in the list.
or
This list can also be displayed by pressing LIST on the
steering mounted controls.
267
07 RADIO
Changing waveband
Selecting a station
The external environment (hill, building, tunnel, underground car park…) may interfere with the reception, including in RDS station tracking mode.
This phenomenon is a normal result of the way in which radio waves are transmitted and does not in any way indicate a fault with the audio system.
The quality of reception is represented by the number of
active waves in this symbol.
Press RADIO or OK to display the
contextual menu.
Select "Change waveband".
Select "AM / FM" and confirm.
268
By alphabetical list
Press RADIO or LIST, select the station
of your choice and confirm.
By automatic frequency search
Press  or  for the automatic search
for a lower or higher radio frequency.
Or turn the thumb wheel at the steering
mounted controls.
By manual frequency search
Press  or  to adjust the radio
frequency step by step.
07 RADIO
Presetting a station
Activate / Deactivate RDS
RDS, if activated, allows you to continue listening to the same
station by automatic retuning to alternative frequencies. However,
in certain conditions, coverage of an RDS station may not be
assured throughout the entire country as radio stations do not
cover 100 % of the territory. This explains the loss of reception of
the station during a journey.
After selecting a station, press one of
the buttons on the numerical keypad for
2 seconds to preset the current station.
An audible signal confirms that the
station has been preset.
Press RADIO.
Select "Guidance options" then
confirm.
Press the button on the numerical
keypad to recall a preset station.
Or press then turn the thumb wheel at
the steering mounted controls.
Activate or deactivate "RDS" then
confirm.
269
07 RADIO
DAB (Digital Audio Broadcasting)
Digital radio
Digital radio - DAB/FM auto tracking
Digital radio provides a higher quality reception and also the
graphical display of information for the radio station, by selecting
"Video mode" in "Radio favourites" (Options).
The different radio multiplex services offer a choice of stations
displayed in alphabetical order.
"DAB" does not have 100% coverage of the country.
When the digital signal is weak, "DAB / FM auto tracking" allows you
to continue listening to the same station, by automatically switching
to the corresponding analogue "FM" station (if one exists).
Press "RADIO".
Press "RADIO".
Select "Options" and confirm.
Select "Change band" and confirm.
Select "FM/DAB" and confirm.
Selection "DAB" and confirm.
Change of station in the same "multiplex".
Manual search for a "multiplex".
270
If "DAB / FM auto tracking" is on, there will be a difference of a few
seconds in the programme when the system changes to analogue
"FM" radio with sometimes a variation in volume.
Display of the "DAB" band then becomes "DAB (FM)".
When the strength of the digital signal is good again, the system
automatically switches back to "DAB".
If the "DAB" station you are listening to is not available on "FM"
("DAB/FM" option greyed out), or if "DAB / FM auto tracking" is not
on, the sound will be cut when the digital signal is too weak.
08 MUSIC MEDIA PLAYERS
Access to the "MUSIC MEDIA PLAYER" menu
"MEDIA"
Press MUSIC.
List of the current media
tracks.
"Change Media"
"Eject USB device" (if USB
connected)
"Play mode" ("Normal",
"Random", "Random on all
media", "Repetition")
"Audio settings" (see this section)
"Activate / Deactivate AUX input"
Go from the list to the menu (left/right).
This list can also be displayed by pressing LIST
at the steering mounted controls.
or
271
08 MUSIC MEDIA PLAYERS
CD, MP3 CD / USB player
Information and advice
The audio equipment will only play audio files with ".wma, .aac, .flac,
.ogg and .mp3" file extensions and with a bit rate of between 32 Kbps
and 320 Kbps.
It also supports VBR (Variable Bit Rate) mode.
No other type of file (.mp4, .m3u…) can be played.
WMA files must be of the standard wma 9 type.
The sampling rates supported are greater than 32 KHz.
It is advisable to restrict file names to 20 characters, without using of
special characters (e.g.: " " ? ; ù) to avoid any playing and displaying
problems.
In order to be able to play a recorded CDR or CDRW, when recording
it is preferable to select the ISO 9660 level 1, 2 or Joliet standard.
If the disc is recorded in another format (udf, …), it may not be played
correctly.
It is recommended that the same recording standard is always used
for an individual disc, with as low a speed as possible (4x maximum)
for optimum sound quality.
In the particular case of a multi-session CD, the Joliet standard is
recommended.
272
The system supports USB mass storage or iPod
devices via the USB port (suitable cable not supplied).
If a partitioned USB memory key is connected to the
system, only the first partition is recognised.
Control of the peripheral device is with the audio
system controls.
The number of tracks is limited to 2000 maximum,
999 tracks per folder.
If the current consumption at the USB port exceeds
500 mA, the system goes into protection mode and
deactivates the port.
Other peripherals, not recognised on connection, must
be connected to the auxiliary socket using a Jack cable
(not supplied).
In order to be read, a USB memory stick must be formatted FAT 16 or 32.
The system does not support the operation of an Apple® player and a
USB memory stick connected at the same time.
It is recommended that official Apple® USB cables are used to ensure
correct operation.
08 MUSIC MEDIA PLAYERS
Sources
Selection of source
The SOURCE button on the steering mounted controls allows a
direct change to the next media source.
Insert the CD in the player, insert the USB memory
stick in the USB player or connect the USB
peripheral to the USB port using a suitable cable
(not supplied).
The system builds playlists (in temporary memory),
an operation which can take from a few seconds to
several minutes at the first connection.
Reduce the number of non-music files and the
number of folders to reduce the waiting time.
The playlists are updated every time the ignition is
switched off or connection of a USB memory stick.
However, the system memorises these lists and
if they are not modified, the loading time will be
shorter.
Play starts automatically after a period which
depends on the capacity of the USB memory stick.
"CD / CD MP3"
"RADIO"
"STREAMING"
"USB, iPod"
"AUX"
Press MUSIC to display the "MEDIA"
menu.
Select "Following media source" and
confirm.
Repeat the operation as many times as necessary to obtain the
desired media source (except for radio which is accessible either
with SOURCE or RADIO).
273
08 MUSIC MEDIA PLAYERS
SELECTING A TRACK
Previous track.
/
Next track.
/
LIST: List of USB or CD tracks
or folders
Up or down in the list.
/
Confirm, next menu level.
/
/
Previous folder.
Next folder.
Fast forward.
/
Long press
+
Fast backward.
Long press
Up one menu level.
/
Pause: long press on SRC.
274
/
/
08 MUSIC MEDIA PLAYERS
Connecting APPLE® players
Connect the Apple® player to the USB port using a suitable cable (not
supplied).
Play starts automatically.
Audio streaming
Streaming allows audio files on your telephone to be played via the
vehicle's speakers.
Control is via the audio system.
The classifications available are those of the portable device
connected (artists / albums / genres / playlists / audiobooks /
podcasts).
The default classification used is by artist. To modify the classification
used, return to the first level of the menu then select the desired
classification (playlists for example) and confirm to go down through
the menu to the desired track.
The "Shuffle tracks" mode on an iPod® corresponds to the "Random"
mode on the audio system.
The "Shuffle albums" mode on an iPod® corresponds to the "Random
all" on the audio system.
"Shuffle tracks" is restored by default on each connection.
The version of software in the audio system may not be compatible
with the generation of your Apple® player.
Connect the telephone: see "USING THE TELEPHONE".
Select "Audio" or "All" profile.
If play does not start automatically, it may be necessary to start the
audio playback from the telephone.
Control is from the peripheral device or by using the audio system
buttons.
Once connected in streaming mode, the telephone is considered to be
a media source.
It is recommended that you activate "Repeat" on the Bluetooth
peripheral.
275
08 MUSIC MEDIA PLAYERS
USING THE AUXILIARY INPUT (AUX)
JACK/RCA AUDIO CABLE NOT SUPPLIED
Connect the portable device (MP3, WMA player…) to the RCA audio
sockets (white and red) using a JACK-RCA audio cable.
Press MUSIC to display the "MUSIC"
menu.
Select "Activate / Deactivate AUX
input" and confirm.
First adjust the volume of your portable
device (to a high level). Then adjust the
volume of your audio system.
Display and management of the controls are via the portable device.
276
09 AUDIO SETTINGS
They are accessible by the MUSIC
button in the control panel or by a long
press on RADIO according to the source
in use.
-
"Equalizer" (choice of 6 musical ambiences)
"Bass"
"Treble"
"Loudness" (Activate/Deactivate)
"Distribution" ("Driver", "All passengers")
"Le-Ri balance" (Left/Right)
"Fr-Re balance" (Front/Rear)
"Auto. Volume" depending on road speed (Activate/Deactivate)
The distribution (or spatialisation using the Arkamys© system) of sound
is an audio process that allows the audio quality to be adapted to the
number of listeners in the vehicle.
The audio settings (Equalizer, Bass, Treble and Loudness) are
different and independent for each sound source.
The settings for distribution and balance are common to all sources.
On-board audio: Arkamys© Sound Staging.
With Sound Staging, the driver and passengers are immersed in an
"audio scene" recreating the natural atmosphere of an auditorium:
truly a part of the scene and its surroundings.
This new sensation is made possible by software in the audio system
which processes the digital signals from the media players (radio,
CD, MP3…) without changing the audio settings. This processing
takes account of the characteristics of the passenger compartment to
produce optimum results.
The Arkamys© software installed in your audio system processes
the digital signal from the media players (radio, CD, MP3, …) and
recreates a natural musical scene, with harmonious placement of
instruments and voices in the space in front of passengers, level with
the windscreen.
277
10 CONFIGURATION
Display configuration
278
Press SETUP to display the
"Configuration" menu.
Select "Choose colour" and confirm to
select the screen colour harmony and
the map presentation mode:
day mode,
night mode,
automatic day/night mode,
according to whether the
headlamps are on.
Select "Display configuration" and
confirm.
Select "Adjust luminosity" and confirm
to adjust the screen brightness.
Press "OK" to save the changes.
The settings for day and night are
independent.
11 SCREEN MENU MAP(S)
MAIN FUNCTION
1
2
3
1
3
Option A
2
Option A1
2
Option A11
2
Option B…
Chosen destination
3
Select destination
2
2
3
3
3
Enter an address
3
Directory
3
GPS coordinates
Journey leg and route
1
Add a stage
Enter an address
3
3
2
2
2
3
Define calculation criteria
3
2
3
Guidance options
"NAVIGATION - GUIDANCE"
MENU
2
2
Divert route
1
Map management
1
Order/delete journey legs
2
1
Previous destinations
2
Fastest route
2
Shortest route
2
Distance/Time
2
With tolls
With Ferry
2
Traffic info
2
Delete last destinations
Set parameters for risk areas
Vehicle direction
North direction
Perspective view
Map details
Move the map
Mapping and updating
Description of risk areas database
Stop / Restore guidance
1
Set speech synthesis
Map orientation
2
2
2
Directory
2
Fastest route
Shortest route
Distance/Time
With tolls
With Ferry
Traffic info
279
11 SCREEN MENU MAP(S)
"TRAFFIC INFORMATION"
MENU
2
Retain the messages:
2
3
Around the vehicle
On the route
Select TMC station
2
2
2
1
Manual TMC
List of TMC stations
3
3
3
1
Directory of contacts
280
3
2
3
3
Synchronization options
2
Dial
3
Import all the entries
2
"TELEPHONE" MENU
3
Delete all contacts
2
Display / Do not display
messages
3
Sort by Name/First name
2
2
No synchronization
Display telephone contacts
Display SIM card contacts
Display all phone contacts
Contact mem. status
List of the paired peripherals
2
New contact
2
Automatic TMC
1
Bluetooth functions
1
Contacts management
1
Delete calls log
2
Cancel
2
3
1
Delete
2
Ring options
2
Import
2
Retain all the messages:
Phone functions
1
Open
2
Geographic filter
1
Call
2
2
1
Connect
Disconnect
Delete
Delete all
Cancel
Peripherals search
Rename radiotelephone
Hang up
11 SCREEN MENU MAP(S)
"RADIO" MENU
3
3
Change Waveband
1
2
1
2
2
2
2
1
2
FM / DAB / AM
2
Guidance options
2
TA
2
Video mode
3
Audio settings
3
2
Equalizer
3
3
3
3
None
2
Classical
2
3
Jazz
Rock
1
Change Media
1
Treble
2
Loudness
2
2
Activated / Deactivated
2
Distribution
2
FM/DAB (auto tracking)
"MUSIC" MENU
Vocal
Bass
3
RDS options
Techno
Driver
All passengers
CD
BT Streaming
USB/iPod
AUX
Audio settings
1
2
Activate / Deactivate AUX
input
Le-Ri balance
Fr-Re balance
Auto. Volume
Activated / Deactivated
Update radio list
281
11 SCREEN MENU MAP(S)
"SETUP" MENU
1
2
2
2
2
Speech synthesis setting
1
Sound choice
2
Classic
2
Guidance instructions volume
Select male voice/Select female voice
Crystal symphony
1
Select language
Urban rythmik
1
Define vehicle parameters*
Jungle fantasy
1
Alert log
Display configuration
1
2
2
2
2
Choose colour
Adjust luminosity
Set date and time
Select units
* Depending on vehicle equipment.
282
FREQUENTLY ASKED QUESTIONS
The following table groups together the answers to the most frequently asked questions concerning your audio system.
QUESTION
ANSWER
SOLUTION
The route calculation is
not successful.
The guidance criteria may conflict with the current location (exclusion of
toll roads on a toll motorway).
Check the guidance criteria on the Navigation
Menu, "Guidance options"\ "Define calculation
criteria".
I am unable to enter my
post code.
The system only accepts post codes of up to 5 characters.
The POIs do not appear.
The POIs have not been selected.
Select the POIs in the list of POIs.
The risk areas audible
warning does not work.
The audible warning is not active.
Activate audible warnings in the Guidance options
menu, "Navigation - guidance", "Set parameters
for risk areas".
The system does not
suggest a detour around
an incident on the route.
The guidance criteria do not take account of TMC messages.
Select the "Traffic info" function in the list of
guidance criteria.
I receive a Risk area alert
which is not on my route.
Other than guidance, the system announces all Risk areas positioned in a
cone located in front of the vehicle. It may provide an alert for a Risk area
located on nearby or parallel roads.
Zoom in on the map to view the exact position of
the Risk area. Select "On the route" to no longer
receive alerts other than guidance or to reduce the
time for the announcement.
283
FREQUENTLY ASKED QUESTIONS
QUESTION
Certain traffic jams
along the route are not
indicated in real time.
The altitude is not
displayed.
I am unable to connect
my Bluetooth telephone.
ANSWER
SOLUTION
On starting, it is several minutes before the system begins to receive the
traffic information.
Wait until the traffic information is being received
correctly (display of the traffic information icons on
the map).
The filters are too restrictive.
Modify the "Geographic filter" settings.
In certain countries, only major routes (motorways…) are listed for the
traffic information.
This phenomenon is normal. The system is
dependent on the traffic information available.
On starting, the initialisation of the GPS may take up to 3 minutes to
receive more than 4 satellites correctly.
Wait until the system has started up completely.
Check that there is a GPS coverage of at least
4 satellites (long press on the SETUP button, then
select "GPS coverage").
Depending on the geographical environment (tunnel…) or the weather,
the conditions of reception of the GPS signal may vary.
This phenomenon is normal. The system
is dependent on the GPS signal reception
conditions.
The telephone's Bluetooth function may be switched off or the telephone
may not be visible.
-
The volume of the
telephone connected
in Bluetooth mode is
inaudible.
284
Check that your telephone's Bluetooth
function is switched on.
Check in the telephone settings that it is
"visible to all".
The Bluetooth telephone is not compatible with the system.
You can check the compatibility of your telephone
on www.citroen.co.uk (services)
The volume depends both on the system and on the telephone.
Increase the volume of the audio system, to
maximum if required, and increase the volume of
the telephone if necessary.
The ambient noise level has an influence on the quality of telephone
communication.
Reduce the ambient noise level (close the windows,
reduce the booster fan speed, slow down, …).
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
Some contacts are
duplicated in the list.
The options for synchronizing contacts are synchronizing the contacts
on the SIM card, the contacts on the telephone, or both. When both
synchronizations are selected, some contacts may be duplicated.
Select "Display SIM card contacts" or "Display
telephone contacts".
Contacts are not shown
in alphabetical order.
Some telephones offer display options. Depending on the settings
chosen, contacts can be transferred in a specific order.
Modify the display setting in the telephone
directory.
The system does not
receive SMS text messages.
The Bluetooth mode does not permit sending SMS text messages to the
system.
The CD is ejected
automatically or is not
played by the player.
The CD is inserted upside down, is unplayable, does not contain any
audio data or contains an audio format which the player cannot play.
The CD has been recorded in a format that is not compatible with the
player (udf, …).
The CD is protected by an anti-pirating protection system which is not
recognised by the audio system.
-
Check that the CD is inserted in the player the right
way up.
Check the condition of the CD: the CD cannot be
played if it is too damaged.
Check the content in the case of a recorded CD:
refer to the information and advice in the "MUSIC
MEDIA PLAYERS" section.
The audio system's CD player does not play DVDs.
Some recorded CDs will not be played by the audio
system because they are not of the correct quality.
There is a long waiting period
following the insertion of a CD
or connection of a USB memory
stick.
When a new medium is inserted, the system reads a certain amount of
data (directory, title, artist, etc.). This may take from a few seconds to a
few minutes.
This phenomenon is normal.
The CD player sound is
poor.
The CD used is scratched or of poor quality.
Insert good quality CDs and store them in suitable
conditions.
The audio equipment settings (bass, treble, ambiences) are unsuitable.
Set the treble or bass level to 0, without selecting
an ambience.
285
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
Some characters in the
media information are not
displayed correctly while
playing.
The audio system does not display some types of characters.
Use standard characters to name tracks and
folders.
Playing of streaming files
does not start.
The peripheral device connected does not support automatic play.
Start the playback from the device.
The names of tracks and
the track length are not
displayed on the screen
when streaming audio.
The Bluetooth profile does not allow the transfer of this information.
The quality of reception
of the radio station
listened to gradually
deteriorates or the stored
stations do not function
(no sound, 87.5 Mhz is
displayed…).
The vehicle is too far from the transmitter used by the station listened
to or there is no transmitter in the geographical area through which the
vehicle is travelling.
Activate the "RDS" function by means of the
short-cut menu to enable the system to check
whether there is a more powerful transmitter in the
geographical area.
The environment (hills, buildings, tunnels, basement car parks…) block
reception, including in RDS mode.
This phenomenon is normal and does not indicate
a fault with the audio system.
The aerial is absent or has been damaged (for example when going
through a car wash or into an underground car park).
Have the aerial checked by a CITROËN dealer.
I cannot find some radio
stations in the list of
stations received.
The name of the radio
station changes.
286
The station is not received or its name has changed in the list.
Some radio stations send other information in place of their name (the
title of the song for example).
The system interprets this information as the name of the station.
FREQUENTLY ASKED QUESTIONS
QUESTION
In changing the setting
of treble and bass the
equalizer setting is
deselected.
ANSWER
SOLUTION
The selection of an equalizer setting imposes the balance settings.
Modifying one without the other is not possible.
Modify the balance or equalizer settings to obtain
the desired musical ambience.
The selection of a distribution setting imposes the balance settings.
Modifying one without the other is not possible.
Modify the balance or distribution settings to
obtain the desired musical ambience.
For optimum sound quality, the audio settings for Volume, Bass, Treble,
Equalizer and Loudness can be adapted to the different sound sources,
which may result in audible differences when changing source (radio,
CD…).
Check that the audio settings for (Volume, Bass,
Treble, Equalizer, Loudness) are adapted to
the sources listened to. It is advisable to set the
AUDIO functions (Bass, Treble, Fr-Re balance,
Le-Ri balance) to the middle position, select the
"None", musical ambience and set the loudness
correction to the "Active" position in CD mode or
to the "Inactive" position in radio mode.
In changing the equalizer
setting, treble and bass
return to zero.
When changing the
balance settings, the
distribution setting is
deselected.
When changing an
distribution setting,
the balance setting is
deselected.
There is a difference in
sound quality between
the different audio
sources (radio, CD…).
287
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
With the engine off, the
system switches off after
a few minutes of use.
When the engine is switched off, the system's operating time depends on
the battery charge.
The switch-off is normal: the system switches to economy mode and
switches off to prevent discharging of the vehicle's battery.
Start the vehicle's engine to increase the battery
charge.
Playback of my USB
memory stick starts only
after a very long wait
(around 2 to 3 minutes).
Some files supplied with the memory stick may greatly slow down access
to reading the memory stick (multiplication by 10 of the catalogue time).
Delete the files supplied with the memory stick
and limit the number of sub-folders in the file
structure on the memory stick.
When I connect my
iPhone as telephone and
to the USB port at the
same time, I am unable
to play the music files.
When the iPhone connects automatically as a telephone, it forces the
streaming function. The streaming function takes the place of the USB
function which is then not useable, there is a period without sound of the
track being played with Apple® players.
Disconnect and reconnect to the USB port (the
USB function takes priority over streaming).
When I connect my
Apple® player or my
BlackBerry® to the
USB port, I have alert
messages on the current
consumption by the USB
port.
When charging, the current consumption of these smartphones is greater
than the rating of the USB port, which is 500 mA.
288
SOLUTION
AUDIO SYSTEM / BLUETOOTH
CONTENTS
The system is coded in such a way that it will only
operate in your vehicle.
For safety reasons, the driver must only carry out
operations which require prolonged attention while the
vehicle is stationary.
When the engine is switched off and to prevent
discharging of the battery, the audio system may switch
off after a few minutes.
01 First steps
p.
290
02 Steering mounted controls
p.
291
03 Main menu
p.
292
04 Audio
p.
293
05 Using the telephone
p.
304
06 Audio settings
p.
312
07 Screen menu map
p.
314
Frequently asked questions
p.
317
289
01 FIRST STEPS
Select screen display
between modes:
Full screen: Audio (or
telephone if call in
progress) /
In a window: Audio
(or telephone if call in
progress) - Time or Trip
computer.
Long press: black screen
(DARK).
Display the list of stations
received, CD/MP3 tracks or
folders.
Long press: managing the
classification of MP3/WMA
files / update the list of stations
received.
Manual step by step search up / down
for radio frequencies.
Select previous / next MP3 folder.
Select previous / next folder / genre /
artist / playlist in the USB device.
Navigation in a list.
Automatic search up / down for radio
frequencies.
Select previous / next CD, USB,
streaming track.
Navigation in a list.
Abandon the current
operation.
Up one level (menu or
folder).
Select preset radio station.
Long press: store a station.
Selection of AM / FM /
DAB* wavebands.
Access to main menu.
On / Off.
Volume adjustment.
TA (Traffic
Announcement)
function On / Off.
Long press:
access to type of
information.
Audio settings:
audio ambiences, treble,
bass, loudness, distribution,
left/right balance, front/rear
fader, automatic volume.
Select source:
Radio, CD, AUX, USB,
Streaming.
Accept an incoming
call.
Confirmation or display of
contextual menu.
* Depending on model.
290
02 STEERING MOUNTED CONTROLS
Audio system
Audio / Bluetooth telephone system
-
Short press: mute: change multimedia source.
Long press: mute / restore sound.
-
-
-
-
Rotation:
Radio: automatic search for the previous / next station.
Media: previous / next track.
Press: confirmation.
Short press:
Radio: display the list of stations.
Media: display the list of tracks.
Long press: update the list of stations received.
Increase volume.
Decrease volume.
-
Short press:
Change multimedia source.
Accept an incoming call.
Call in progress: access to the telephone menu (End call, Secret
mode, Hands-free mode).
Long press:
Reject an incoming call.
End a call in progress.
No call in progress: access to the telephone menu (Call, Contacts,
call log, Voice mail).
Rotation.
Radio: automatic search for the previous / next station.
Media: previous / next track.
Press: confirmation.
-
Short press:
Radio: display the list of stations.
Media: display the list of tracks.
Long press: update the list of stations received.
-
Increase volume.
Decrease volume.
291
03 MAIN MENU
"Telephone": Call, Directory
management, Telephone
management, Hang up.
"Bluetooth connection":
Connections management,
Search for a device.
Screen C
"Multimedia": Media parameters,
Radio parameters.
"Trip computer": Warning log.
"Personalisation-configuration": Define
the vehicle parameters, Choice of language,
Display configuration, Choice of units, Date
and time adjustment.
Screen A
For a detailed global view of the
menus available, refer to "Screen
menu map" section.
292
04 AUDIO
Radio
Selecting a station
The exterior environment (hills, buildings, tunnel, car park, below
ground...) may prevent reception, even in RDS station tracking
mode. This phenomenon is normal in the propagation of radio
waves and is in no way indicative of a fault with the audio system.
Press LIST to display the list of stations
received in alphabetical order.
Press SOURCE or SRC several times in
succession and select radio.
Select the desired radio station and
confirm by pressing OK.
Press BAND to select a waveband.
A press changes to the next or previous
letter (e.g. A, B, D, F, G, J, K, ...).
A long press on LIST builds or updates
the list of stations; audio reception is cut
momentarily.
293
04 AUDIO
Receiving INFO messages
RDS
RDS, if displayed, enables you to continue listening to the same station
by automatic retuning to alternative frequencies. However, in certain
conditions, coverage of an RDS station may not be assured throughout
the country as radio stations do not cover 100 % of the territory. This
explains the loss of reception of the station during a journey.
When the radio is displayed on the
screen, press OK to display the
contextual menu.
The INFO function gives priority to TA alert messages. To be
active, this function needs good reception of a radio station that
transmits this type of message. When a message is transmitted,
the current audio source (Radio, CD, USB, ...) is interrupted
automatically to receive the INFO message. Normal play resumes
at the end of the message transmission.
Select "RDS" and confirm to save.
"RDS" is displayed in the screen.
Receiving TA messages
The TA (Traffic Announcement) function gives priority to TA alert
messages. To operate, this function needs good reception of a
radio station transmitting this type of message. When a traffic
report is transmitted, the current audio source (Radio, CD,
USB, ...) is interrupted automatically to play the TA message.
Normal playback of the audio source resumes at the end of the
transmission of the message.
Press TA INFO to activate or deactivate
the reception of traffic messages.
294
Make a long press on TA INFO to
display the list of categories.
Select or deselect categories to activate
or deactivate the reception of the
corresponding messages.
04 AUDIO
Display RADIO TEXT
Radio text is information transmitted by the radio station related to the current programme or song.
Screen C
Screen A
With the radio displayed on the screen,
press OK to display the contextual
menu.
Select "RadioText (TXT) display" and
confirm OK to save.
Select "MEDIA" and confirm.
Then select "TEXT INFO" and press
 or  to select "ON" or "OFF" and
confirm to save the modifications.
295
04 AUDIO
DAB (Digital Audio Broadcasting)
Digital radio
Digital radio - DAB / FM tracking
Digital radio provides a superior audio quality and also additional
categories of traffic announcements (TA INFO).
The different "multiplex services" offer a choice of radio stations in
alphabetical order.
"DAB" does not have 100% coverage of the country.
When the digital signal is weak, "DAB / FM auto tracking" allows you
to continue listening to the same station, by automatically switching
to the corresponding analogue "FM" station (if it exists).
Change band (FM1, FM2, DAB, ...)
Change of station within the same "multiplex service".
Start a search for the next "multiplex service".
Long press: select the desired categories of
announcements from Transport, News, Entertainment
and Flash special (availability according to the station).
When the radio station is displayed in the screen, press on "OK" to
display the contextual menu.
(Frequency hopping (RDS), DAB / FM auto tracking, RadioText
(TXT) display, Information on the station, ...)
296
Press the "Menu" button.
Select "Multimedia" and confirm.
Select "DAB / FM auto tracking" and confirm
If "DAB / FM auto tracking" is on, there will be a difference of a few
seconds in the programme when the system changes to analogue
"FM" radio, with sometimes a variation in volume.
When the strength of the digital signal is good again, the system
automatically switches back to "DAB"
If the "DAB" station you are listening to is not available on "FM"
("DAB/FM" option barred), or if "DAB / FM auto tracking" is not on,
the sound will be cut when the digital signal is too weak.
04 AUDIO
Audio CD
Playing a CD
Insert 12 cm diameter circular compact discs only.
Some anti-pirating systems, on original discs or CDs copied using a
personal recorder, may cause faults which are no reflection on the
quality of the original player.
Without pressing the EJECT button, insert a CD in the player, play
begins automatically.
To play a disc which has already been
inserted, press the SOURCE or SRC
button several times in succession and
select "CD".
Press LIST to display the list of tracks
on the CD.
Press and hold one of the buttons for
fast forward or backward.
Press one of the buttons to select a
track on the CD.
297
04 AUDIO
CD, USB
Information and advice
The audio system will only play files with extension ".mp3" or ".wma"
and a compression rate that is constant or variable between 32 Kbps
and 320 Kbps.
It is advisable to restrict file names to 20 characters without using
special characters (e.g. " ? ; ù) to avoid any playing or displaying
problems.
The playlists accepted are types .m3u and .pls.
The number of files is limited to 5 000 in 500 directories on a
maximum of 8 levels.
298
On a single disc, the CD player can read up to 255 MP3 files spread
over 8 directory levels. However, it is recommended that this be kept
to 2 levels so as to limit the time taken to access and play the CD.
During play, the folder structure is not observed.
In order to be able to play a recorded CDR or CDRW, when recording
it is preferable to select standards ISO 9660 level 1.2 or Joliet.
If the disc is recorded in another format, it may not be played correctly.
It is recommended that the same recording standard is always used
for an individual disc, with as low a speed as possible (4x maximum)
for optimum sound quality.
In the particular case of a multi-session CD, the Joliet standard is
recommended.
Do not connect a hard disk or USB device other than audio players to
the USB port. This may cause damage to your installation.
04 AUDIO
CD, USB
Playing a compilation
Press one of the buttons to select the
next or previous track.
Insert an MP3 compilation in the CD player or
connect a memory stick to the USB port, directly or
via an extension lead.
The system creates playlists (temporary memory) the creation time
for which can take from a few seconds to several minutes.
The playlists are updated every time the ignition is switched off or a
USB memory stick is connected.
Play starts automatically after a period which depends on the
capacity of the USB memory stick.
At a first connection, the order suggested is by folder.
When connecting again, the order previously chosen is
retained.
To play a disc or memory stick which
has already been inserted, press
SOURCE or SRC several times in
succession and select "CD" or "USB".
Press one of the buttons to select the
next or previous folder in the order
chosen.
Press and hold one of the buttons for
fast forwards or backwards.
Press LIST to display the menu of
folders in the compilation.
299
04 AUDIO
USB memory stick - File sorting
Select a line in the list.
Make a long press on LIST or press
MENU, select "Multimedia", then
"Media parameters" and finally "Choice
of track listing" to display the different
types of sorting.
Select a track or a folder.
Up a level in the menu.
Skip a track.
300
Having selected the desired sorting ("By
folders", "By artists", "By genres", "By
playlists") press OK.
Then confirm OK to save the modifications.
By folders: all folders containing audio
files recognised on the peripheral device,
in alphabetical order without following the
folder structure.
By artists: all of the artist names defined
in the ID3 Tags, in alphabetical order.
By genres: all of the genres defined in the
ID3 Tags.
By playlists: if playlists have been saved.
04 AUDIO
APPLE® players or portable player
The audio files on a Mass Storage portable player* can
be heard through the vehicle's speakers by connecting
it to the USB port (cable not supplied).
The Apple® player must be updated regularly for the best connection.
Management of the device is via the audio system controls.
The playlists are those defined in the Apple® player.
If the portable player is not recognised by the USB port, connect it to
the auxiliary Jack socket.
The Apple® player must be generation 5 or later.
* Check your player's manual.
301
04 AUDIO
Auxiliary socket (AUX)
Auxiliary Jack socket
The auxiliary Jack socket permits the connection of a portable nonmass storage device or an Apple® player if not recognised by the
USB port.
Do not connect a device to the USB port and to the auxiliary Jack
socket at the same time.
Connect the portable device to the auxiliary Jack socket using a
suitable cable (not supplied).
Press the SOURCE or SRC button
several times in succession and
select "AUX".
First adjust the volume on your portable device.
Then adjust the volume of the audio
system.
The display and management of controls is on the
portable device.
302
04 AUDIO
Streaming - Playing audio files via
Bluetooth
Depending on the compatibility of the phone
Streaming allows music files on a telephone to be heard via the
vehicle's speakers.
The telephone must support the appropriate bluetooth profiles
(Profiles A2DP / AVRCP).
Pair/connect the telephone: see the "USING THE
TELEPHONE" section.
Play mode
The play modes available are:
Normal: the tracks are played in order, depending on the
classification of the selected files.
Random: the tracks in an album or folder are played in a
random order.
Random all: all of the tracks saved in the media are played in
random order.
Repeat: the tracks played are only those from the current
album or folder.
Press OK for access to the contextual
menu.
or
Press MENU.
Select "Multimedia" and confirm.
Activate the streaming source by pressing SOURCE or
SRC. Control of playback is via the audio system. The
contextual information can be displayed in the screen.
Select "Media parameters" and
confirm.
In certain cases, playing of the audio files must be initiated from the
telephone.
Select "Read mode" and confirm.
The audio quality depends on the quality of the transmission from
the telephone.
Select the desired play mode and
confirm OK to save the modifications.
303
05 USING THE TELEPHONE
Pairing a telephone
First connection
The services offered depend on the network, the SIM card and the compatibility of the Bluetooth telephone used.
Consult your telephone's manual and your operator to find out which services are available to you.
For safety reasons and because they require prolonged attention on the part of the driver, the operations for pairing of the Bluetooth mobile
telephone with the Bluetooth hands-free system of your audio system must be carried out with the vehicle stationary and the ignition on.
Visit www.citroen.co.uk for more information (compatibility, additional help, ...).
Activate the telephone's Bluetooth function and
ensure that it is "visible to all" (refer to the telephone
user guide).
Press MENU.
Select "Bluetooth connection" and
confirm.
304
Select "Search for a device".
A window is displayed "Search in progress…"
Select the telephone to be connected
from the list. Only one telephone can
be connected at a time.
05 USING THE TELEPHONE
In some cases, the reference number of the telephone or the
Bluetooth address may appear instead of the name of the telephone.
Accept the connection to the telephone.
A message appears in the screen to confirm the result of the
connection.
A virtual keypad is displayed on the
screen: enter a code with at least
4 digits and conform with OK.
Pairing can also be initiated from the telephone by searching for
detected Bluetooth devices.
Saisir code authentification
_
0
OK
1
2
3
4
5
6
7
8
9
Del
The directory and the calls list can be accessed after the
synchronisation period (if the telephone is compatible).
Automatic connection must be configured in the telephone to allow
the connection each time the vehicle is started.
A message is displayed on the screen of the
telephone: enter the same code and confirm.
Streaming - Playing audio files via
Bluetooth
If pairing fails, try again; the number of attempts is not limited.
Pair/connect the telephone then listen: see the AUDIO section.
305
05 USING THE TELEPHONE
Managing connections
The telephone connection automatically includes hands free operation
and audio streaming.
The ability of the system to connect to just one profile depends on the
telephone. Both profiles may connect by default.
Indicates that a device is connected.
Indicates connection of the audio steaming profile.
Indicates connection of the hands-free profile.
Press MENU.
Select a telephone and confirm.
Select "Bluetooth connection" and
confirm.
Select "Connections management"
and confirm. The list of paired
telephones is displayed.
306
Then select and confirm:
"Connect telephone" / "Disconnect
telephone": to connect / disconnect
the telephone or the hands-free
connection only.
"Connect media player" /
"Disconnect media player": to
connect / disconnect only streaming.
"Connect telephone + media
player" / "Disconnect telephone +
media player": to connect /
disconnect the telephone (hands-free
and streaming).
"Delete connection": to delete the
pairing.
05 USING THE TELEPHONE
Making a call - Dialling
To display the "TELEPHONE" menu:
Make along press on SOURCE or SRC.
Or, press OK to display the
contextual menu. Select "Call" and
confirm.
Or, press MENU, select
"Telephone" and confirm. Select
"Call" and confirm.
Select "Dial" to enter a number and
confirm.
Select numbers one at a time using
the  and  buttons and confirm.
Correction allows numbers to be deleted one at a time.
Select OK and confirm to start the
call.
Making a call - Recently called numbers*
To display the "TELEPHONE" menu:
Make a long press on SRC/TEL.
Or, press the dial to display the
contextual menu. Select "Call" and
confirm.
Or, press MENU, select "Telephone"
and confirm. Select "Call" and
confirm.
Select "Calls list" and confirm.
Select the number and confirm to
start the call.
The calls list includes calls sent and received in the vehicle using the
connected telephone.
It is possible to make a call directly from the telephone; park the
vehicle first as a safety measure.
* Depending on the compatibility of the telephone.
307
05 USING THE TELEPHONE
Making a call - From the directory of contacts
To display the "TELEPHONE" menu:
Make a long press on SRC/TEL.
Or, press the dial to display the
contextual menu. Select "Call" and
confirm.
Or, press MENU, select "Telephone"
and confirm. Select "Call" and
confirm.
Select "Directory" and confirm.
Select a contact then confirm.
Home
Receiving a call
An incoming call is announced by a ring and a superimposed display
in the multifunction screen.
"YES" to accept the call is selected by
default.
Press OK to accept the call.
Select "NO" and confirm to reject the
call.
or
Press one of these buttons to accept
the call.
Business
Mobile
(depending on the information
available in the contact records of
the telephone connected).
A long press on ESC or on TEL,
SOURCE or SRC also rejects an
incoming call.
Select the number and confirm.
308
05 USING THE TELEPHONE
Managing calls
Secret - Mute
(so that the caller cannot hear)
During a call, press OK to display the
contextual menu.
Hang up
In the contextual menu:
select "Micro OFF" to switch off the
microphone.
deselect "Micro OFF" to switch the
microphone on.
In the contextual menu, select "Hang
up" to end the call.
A long press on one of these buttons
also ends the call.
309
05 USING THE TELEPHONE
Combined mode
(to leave the vehicle without ending the call)
In the contextual menu:
select "Telephone mode" to
transfer the call to the telephone.
deselect "Telephone mode" to
transfer the call to the vehicle.
Interactive voice response
From the contextual menu, select
"DTMF tones" and confirm to use
the digital keypad to navigate in the
interactive voice response menu.
Consultation call
In certain cases, the combined mode has to activated from the
telephone.
If the contact has been cut off, when you reconnect on returning to
the vehicle, the Bluetooth connection will be restored automatically
(depending on the compatibility of the telephone).
310
From the contextual menu, select
"Switch" and conform to return to a call
left on hold.
05 USING THE TELEPHONE
Directory
The system accesses the telephone's contacts directory, depending
on compatibility, and while the Bluetooth connection with it is
maintained.
With certain telephones connected by Bluetooth you can send a
contact to the directory of the audio system.
Contacts imported in this way are saved in a permanent directory
visible to all, whatever the telephone connected.
The menu for the directory is not accessible if it is empty.
Make a long press on SOURCE or SRC
for access to the directory
or press OK, and
select "Call" and confirm.
Select "Directory" to see the list of
contacts.
To modify the contacts saved in the
system, press MENU then select
"Telephone" and confirm.
Select "Directory management" and
confirm.
You can:
"Consult an entry",
"Delete an entry",
"Delete all entries".
311
06 AUDIO SETTINGS
Screen A
Press  to display the audio settings
menu.
Press  or  to modify the selected
setting.
Press  or  for the previous or next
setting in the list.
The Ambience, Treble and Bass audio settings are separate and
independent for each sound source.
312
06 AUDIO SETTINGS
Screen C
The distribution (or spatialisation using the Arkamys© system), is
an audio process which allows the sound quality to be improved
according to the setting chosen, corresponding to the position of the
listeners in the vehicle.
The Ambience, Treble and Bass audio settings are different and
independent for each sound source.
Press  to display the audio settings
menu.
The settings available are:
Ambience,
Bass,
Treble,
Loudness,
Distribution: Personalised or Driver,
Left / right balance,
Fader (front / rear balance),
Auto. volume.
On-board audio: Arkamys© Sound Staging.
With Sound Staging, the driver and passengers are immersed in an
"audio scene" recreating the natural atmosphere of an auditorium:
truly a part of the scene and its surroundings.
This new sensation is made possible by software in the audio
system which processes the digital signals from the media players
(radio, CD, MP3…) without changing the audio settings. This
processing takes account of the characteristics of the passenger
compartment to produce optimum results.
The Arkamys© software installed in your audio system processes
the digital signal from the media players (radio, CD, MP3, ...) and
recreates a natural musical scene, with harmonious placement of
instruments and voices in the space in front of passengers, level
with the windscreen.
Select and confirm "Other settings…"
to display the next setting in the list.
313
07 SCREEN MENU MAP(S)
Screen A
MAIN FUNCTION
Option A
1
2
3
1
Option A1
2
Option A11
2
Option B...
RADIO
1
RDS options
1
Infotext
1
Radiotext
TRIP COMPUTER
1
MEDIA
1 Read mode
Diagnostics
2
314
Normal
Random
Random all
LANGUAGES
1 Français
2
2
2
2
2
2
DATE AND TIME
VEHICLE PARAM*
2
Italiano
Nederlands
Portuguès
Portuguès-brasil
Deutsch
English
Español
* Depending on vehicle equipment.
07 SCREEN MENU MAP(S)
Screen C
MULTIMEDIA
1 Media parameters
2
3
3
3
3
2
3
3
3
3
1
TELEPHONE
1 Call
Choice of playback mode
2
Normal
2
Random
2
Random all
Repeat
2
2
By folders
2
By artists
By genres
2
Radio parameters
2
1
Vehicle diagnosis
Directory
BLUETOOTH CONNECTION
Calls list
1
Connections management
Voice mail box
1
Search for a device
Consult an entry
Delete an entry
Delete all entries
Telephone management
1
By playlists
1
Dial
Directory management
1
Choice of track listing
TRIP COMPUTER
Telephone status
Hang up
315
07 SCREEN MENU MAP(S)
PERSONALISATION CONFIGURATION
Define the vehicle
1 parameters*
1
Choice of language
1
Display configuration
2
2
2
2
1
Choice of units
Date and time adjustment
Display parameters
Brightness
Choice of sounds
* Depending on vehicle equipment.
316
FREQUENTLY ASKED QUESTIONS
The following tables contain answers to the most frequently asked questions.
QUESTION
ANSWER
SOLUTION
There is a difference in
sound quality between
the different audio
sources (radio, CD...).
For optimum sound quality, the audio settings (Volume, Bass, Treble,
Ambience, Loudness) can be adapted to the different sound sources,
which may result in audible differences when changing source (radio,
CD...).
Check that the audio settings (Volume, Bass,
Treble, Ambience, Loudness) are adapted to
the sources listened to. It is advisable to set
the AUDIO functions (Bass, Treble, Front-Rear
Fader, Left-Right Balance) to the middle position,
select the musical ambience "None" and set the
loudness correction to the "Active" position in CD
mode or to the "Inactive" position in radio mode.
When changing the
settings for treble and
bass, the ambience
setting is deselected.
When changing the
ambience setting, treble
and bass are reset to
zero.
Choosing an ambience imposes settings for treble and bass. Modifying
one without the other is not possible.
Modify the treble and bass settings or the
ambience setting to obtain the desired sound
quality.
When changing the
balance setting,
distribution is deselected.
Choosing a distribution setting imposes a balance setting. Modifying one
without the other is not possible.
Modify the balance setting or the distribution
setting to obtain the desired sound quality.
317
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
The vehicle is too far from the transmitter used by the station listened
to or there is no transmitter in the geographical area through which the
vehicle is travelling.
Activate the RDS function to enable the system
to check whether there is a more powerful
transmitter in the geographical area.
The environment (hills, buildings, tunnels, basement car parks...) block
reception, including in RDS mode.
This phenomenon is normal and does not indicate
a failure of the audio equipment.
The aerial is absent or has been damaged (for example when going
through a car wash or into an underground car park).
Have the aerial checked by a CITROËN dealer.
Sound cut-outs of 1 to
2 seconds in radio mode.
During this brief sound cut-out, the RDS searches for any frequency
permitting better reception of the station.
Deactivate the RDS function if the phenomenon is
too frequent and always on the same route.
The traffic announcement
(TA) is displayed. I do
not receive any traffic
information.
The radio station does not broadcast traffic information.
Tune to a radio station which broadcasts traffic
information.
The stored stations are
not found (no sound,
87.5 MHz is displayed...).
An incorrect waveband is selected.
Press the BAND button to return to the waveband
on which the stations are stored.
The quality of reception
of the radio station
listened to gradually
deteriorates or the stored
stations do not function
(no sound, 87.5 MHz is
displayed...).
318
FREQUENTLY ASKED QUESTIONS
QUESTION
The CD is ejected
automatically or is not
played by the player.
ANSWER
The CD is inserted upside down, is unplayable, does not contain any
audio data or contains an audio format which the player cannot play.
The CD is protected by an anti-pirating protection system which is not
recognised by the audio equipment.
SOLUTION
-
The CD player sound is
poor.
I am unable to connect
my Bluetooth telephone.
The CD used is scratched or of poor quality.
Insert good quality CDs and store them in suitable
conditions.
The audio settings (bass, treble, ambience) are unsuitable.
Set the treble or bass level to 0, without selecting
an ambience.
It is possible that Bluetooth is switched off on the telephone or that the
telephone has not been made not visible.
-
The Bluetooth connection
is cut.
Check that the CD is inserted in the player the
right way up.
Check the condition of the CD: the CD cannot
be played if it is too damaged.
Check the content in the case of a recorded
CD: consult the advice in the "Audio" section.
The audio equipment's CD player does not
play DVDs.
Due to their quality level, certain writeable
CDs will not be played by the audio system.
Check that your telephone has Bluetooth
switched on.
Check in the telephone's settings that it is
"Visible to all".
The Bluetooth telephone is not compatible with the system.
You can check the compatibility of your telephone
on www.citroen.co.uk (services).
The battery of the peripheral may not be sufficiently charged.
Recharge the battery of the peripheral device.
319
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
The message "USB
device error" is displayed
on the screen.
The USB memory stick is not recognised.
The memory stick may be corrupt.
Reformat the memory stick (FAT 32).
A telephone connects
automatically,
disconnecting another
telephone.
Automatic connection overrides manual connection.
Modify the telephone settings to remove automatic
connection.
The Apple® player is
not recognised when
connecting to the USB
port.
The Apple® player is of a generation that is not compatible with the USB.
Connect the Apple® player to the AUX Jack socket
using a suitable cable (not supplied).
When I connect my
Apple® player or my
BlackBerry® to the
USB port, I have alert
messages on the current
consumption by the USB
port.
When charging, the current consumption of these smartphones is greater
than the rating of the USB port, which is 500 mA.
The hard disk or device
is not recognised when
connecting to the USB
port.
Some hard disks and devices need a power supply greater than is
provided by the audio system.
Connect the device to the 230 V socket, the 12 V
socket or an external power supply.
Caution: ensure that the device does not transmit
a voltage greater than 5 V (risk of destruction of
the system).
When streaming, the
sound cuts momentarily.
Some telephones prioritise connection of the "hands-free" profile.
Delete the "hands-free" connection profile to
improve streaming.
320
FREQUENTLY ASKED QUESTIONS
QUESTION
ANSWER
SOLUTION
In "Random all" play,
not all of the tracks are
played.
In "Random all" play, the system can only take into account up to
999 tracks.
With the engine off, the
audio system switches
off after a few minutes
of use.
When the engine is switched off, the audio system operating time
depends on the battery charge.
The switch-off is normal: the audio system switches to economy mode
and switches off to prevent discharging the vehicle's battery.
Start the vehicle's engine to increase the battery
charge.
The message "the audio
system is overheated"
appears on the display.
In order to protect the installation if the surrounding temperature is too
high, the audio system switches to an automatic thermal protection mode
leading to a reduction of the volume or stopping of the playing of the CD.
Switch the audio system off for a few minutes to
allow the system to cool.
321