Security
System
User's Manual
4110DL/4110XM
N5100V5 Rev B 4/99
TABLE OF CONTENTS
SYSTEM OVERVIEW .......................................................................................................................................4
Keypads....................................................................................................................................................4
Zones .......................................................................................................................................................4
Alarms ......................................................................................................................................................5
Fire Protection ............................................................................................................................................5
Burglary Protection......................................................................................................................................5
Memory of Alarm .........................................................................................................................................5
Pager Notification........................................................................................................................................5
ABOUT THE KEYPADS ....................................................................................................................................6
Keypad Types ............................................................................................................................................6
Keypad Styles ...........................................................................................................................................6
SUMMARY OF SYSTEM STATUS DISPLAYS.........................................................................................................7
SUMMARY OF KEYPAD FUNCTIONS...................................................................................................................8
SECURITY CODES ........................................................................................................................................ 10
Duress Code ............................................................................................................................................ 10
Quick Arming............................................................................................................................................ 10
Assigning/Changing/Deleting User Codes (Using the 8 CODE Key) ................................................................... 11
ENTRY/EXIT DELAYS .................................................................................................................................... 12
CHECKING FOR OPEN ZONES (Using the ✴ READY Key) .................................................................................. 13
BYPASSING PROTECTION ZONES .................................................................................................................. 14
Using The 6 BYPASS Key......................................................................................................................... 14
Quick Bypass........................................................................................................................................... 15
ARMING PERIMETER ONLY, WITH ENTRY DELAY ON (Using The 3 STAY Key) ..................................................... 16
ARMING PERIMETER ONLY, WITH ENTRY DELAY OFF (Using The 7 INSTANT Key ) ............................................... 17
ARMING ALL PROTECTION, WITH ENTRY DELAY ON (Using The 2 AWAY Key)...................................................... 18
ARMING ALL PROTECTION, WITH ENTRY DELAY OFF (Using The 4 MAXIMUM Key) ............................................... 19
–2–
(continued)
TABLE OF CONTENTS
DISARMING THE SYSTEM AND SILENCING ALARMS (Using the 1 OFF Key).......................................................... 20
USING THE KEYSWITCH ................................................................................................................................ 21
CHIME MODE (Using the 9 CHIME Key) ........................................................................................................... 22
PANIC KEYS ................................................................................................................................................ 22
TESTING THE SYSTEM (Using the 5 TEST Key) ................................................................................................ 24
TROUBLE CONDITIONS ................................................................................................................................. 26
"Check" and "Battery" Displays .................................................................................................................... 26
Power Failure............................................................................................................................................ 27
Other Displays.......................................................................................................................................... 28
FIRE ALARM SYSTEM, IF INSTALLED ............................................................................................................... 29
In Case of Fire Alarm .................................................................................................................................. 29
Silencing Fire Alarms.................................................................................................................................. 30
NATIONAL FIRE PROTECTION ASSOCIATION RECOMMENDATIONS ON SMOKE DETECTORS .................................. 31
EMERGENCY EVACUATION............................................................................................................................ 32
QUICK GUIDE TO ALARM SYSTEM FUNCTIONS ................................................................................................. 33
SUMMARY OF AUDIBLE/VISUAL NOTIFICATION ................................................................................................ 34
PROTECTION ZONES LIST ............................................................................................................................. 35
OWNER'S INSURANCE PREMIUM CREDIT REQUEST .......................................................................................... 37
CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT ................................................................... 39
FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENTS......................................................................... 40
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS................................................................................. 41
THE LIMITATIONS OF THIS ALARM SYSTEM...................................................................................................... 42
SERVICING INFORMATION............................................................................................................................. 43
WARRANTY......................................................................................................................................Back Cover
This manual is a step-by-step guide that will aquaint you with the system's features and benefits. It defines the
components and their functions, describes their operation, and instructs you with normal and emergency procedures.
Keep this manual in a convenient place so that you can refer to it as necessary.
–3–
SYSTEM OVERVIEW
General
Keypads
Zones
Congratulations on your ownership of an Ademco Security System.
You've made a wise decision in choosing it, for it represents the latest in
security protection technology today, including microcomputer technology to
monitor all system status. Ademco is the world's largest manufacturer of
security systems and millions of premises are protected by Ademco
systems.
Basically, this system offers you three forms of protection: burglary, fire
and emergency. Your system may consist of at least one keypad which
provides full control of system operation, various sensors such as motion
detectors and door and window sensing devices, plus a selected number
of strategically placed smoke or combustion detectors designed to provide
early warning in case of fire. Your system may also have been programmed to automatically transmit alarm or status messages over the
phone lines to a central alarm monitoring station.
All system functions are controlled by your keypad(s). The keypads
feature a telephone style (digital) keypad and a Liquid Crystal Display
(LCD) which shows the nature and location of all occurrences. Their built-in
sounder will sound during alarm and trouble conditions.
For additional information, see the following section: ABOUT THE
KEYPADS.
Your system's sensing devices have been assigned to various zones. For
example, the sensing device on your Entry/Exit door may have been
assigned to zone 01, sensing devices on windows in the master bedroom
to zone 02, and so on. These zone numbers will appear on the display
when an alarm or trouble condition occurs.
–4–
SYSTEM OVERVIEW
(continued)
Alarms
Fire Protection
Burglary Protection
Memory Of Alarm
Pager Notification
When an alarm occurs, both the keypad and external sounders will sound,
and a message at the keypad will identify the zone(s) causing the alarm. In
addition, if your system is connected to a central monitoring station, an
alarm message will be sent. To stop the alarm sounding, you simply disarm
the system.
The fire protection portion of your security system (if used) is always on
and will sound an alarm if a fire condition is detected. Refer to the FIRE
ALARM SYSTEM section for important information concerning fire protection, smoke detectors and planning emergency exit routes from your
premises.
The burglary protection portion of your system must be turned on or
"armed" before it will sense burglary alarm conditions and sound an alarm.
Your system can be armed in one of four modes: STAY, AWAY, INSTANT
and MAXIMUM. Refer to the ARMING THE SYSTEM sections for
instructions in using these modes of operation.
Your system also provides a CHIME mode for alerting you to the opening
and closing of doors and windows while the system is disarmed.
When an alarm or trouble condition occurs, the keypad displays the
number(s) of the zone(s) that caused the problem, and displays the type
of alarm or trouble (ex. FIRE, ALARM, CHECK). The display remains until it
is cleared by entering the OFF sequence (security code + OFF key) twice.
If you have chosen to be notified of alarms or other system conditions b y
pager, the following codes will be sent to your pager by the control:
1811=Trouble 1911=Alarm
1001=Open
1002=Close
–5–
ABOUT THE KEYPADS
Keypad Types
All commands and procedures described herein are illustrated for FixedWord Display Keypads. However, an Alpha Display Keypad (with a 2line LCD display for more detailed protection point identification and system
status, but with similar commands and procedures) is available and might
have been used instead.
Fixed-Word keypads are available in two styles, A and B, either of which
may have been used in your system. Although different in appearance,
both styles are functionally similar. The keypads on style B keypads are
located behind a flip-down door which can be removed, if desired. Words
displayed on all Fixed-Word keypads are the same, except that their
location in the display window differs slightly with each style.
Note: Some Style B keypads are equipped with a READY indicator in
place of the POWER indicator on Style A keypads. The READY indicator
is lit when the system is ready for arming (no protection zones open).
While the system is disarmed, this indicator will go on and off as protection
zones are opened and closed.
Keypad Styles
Unless noted otherwise, all procedures in this manual apply equally to
all keypad types
and styles.
STYLE A FIXED-WORD KEYPADS
STYLE B FIXED-WORD KEYPADS
00
ALARM
CHECK
FIRE
00
ALARM
CHECK
FIRE
NO AC
AWAY
CHIME
STAY
BAT
INSTANT
BYPASS
NOT READY
NO AC
AWAY
CHIME
STAY
BAT
INSTANT
BYPASS
NOT READY
ARMED
READY
ARMED
POWER
A
OFF
1
2
3
B
MAX
TEST
BYPASS
4
5
6
C
INSTANT
CODE
CHIME
7
8
9
D
READY
0
#
A
1
2
3
OFF
AWAY
STAY
4
MAX
5
6
TEST
BYPASS
7
8
9
INSTANT
CODE
CHIME
*
0
#
B
C
*
AWAY
STAY
PANIC
READY
PANIC
DIAGRAM
SHOWN WITH DOOR REMOVED
–6–
D
SUMMARY OF SYSTEM STATUS DISPLAYS
AWAY
STAY
INSTANT
BYPASS
NOT READY
READY
NO AC
AC
CHIME
BAT
ALARM
CHECK
FIRE
All burglary zones, interior & perimeter,
are armed.
NO AC
AWAY
CHIME
STAY
Perimeter burglary zones, such as windows
BAT
INSTANT
and doors are armed.
ALARM BYPASS
CHECK
Perimeter burglary zones armed and
FIRE
NOT READY
entry delay is turned off.
One or more burglary protection zones
STYLE A
have been bypassed.
Appears when burglary portion of the system
NO AC
is not ready for arming (due to one or more
AWAY
open protection zones).
BYPASS NOT READY
The burglary portion of the system
ALARM
ALARM STAY CHIME BAT
is ready to be armed.
FIRE
FIRE CHECK INSTANT
Appears when AC power has been cut off.
System is operating on backup battery power.
STYLE B
Appears when AC power is present.
FIXED-WORD KEYPAD DISPLAYS
Appears when the CHIME feature is ON.
Low system battery
(if no zone number is shown), or
Low battery condition in a wireless sensor
(if zone number is also shown).
Appears when an intrusion has been detected and the system is armed (also appears
during a fire alarm). Accompanied by the ID # of the protection zone in alarm.
Appears when a malfunction is discovered in the system at any time or if a fault is
detected in a FIRE zone at any time or in a DAY(Trouble)/NIGHT(Alarm) burglary zone
during a disarmed period. Accompanied by a display of zone number in trouble.
Appears when a fire alarm is present. Accompanied by a display of the zone in alarm.
00
00
AWAY
00
00 STAY
–7–
SUMMARY OF KEYPAD FUNCTIONS
1. DISPLAY WINDOW: Displays protection zone
ID and system status messages.
2. 1 OFF KEY: Disarms burglary portion of the
system, silences alarms and audible trouble
indicators, and clears visual display after
problem's correction.
3. 2 AWAY KEY: Arms the entire burglary system, perimeter and interior.
4. 3 STAY KEY: Arms perimeter portion of burglary system only. Interior protection is not
armed, which allows movement within
premises without causing alarm.
5. 4 MAXIMUM KEY: Arms in manner similar to
AWAY mode, but without the entry delay
feature, thus providing maximum protection.
An alarm will occur immediately upon opening
any protection point, including the entry/exit
door.
6. 5 TEST KEY: Tests the system and alarm
sounder if disarmed. Refer to TESTING THE
SYSTEM section for test procedures.
7. 6 BYPASS KEY: Removes individual protection zones from being monitored by the
system.
8. 7 INSTANT KEY: Arms in manner similar to
STAY mode, but without the entry delay
† Note:
9.
10.
11.
12.
13.
14.
feature. Entering via the entry/exit door will
cause an instant alarm.
8 CODE KEY: Used to assign additional user
codes for other users of the system.
9 CHIME KEY: Turns CHIME mode on and
off. When on, the opening of windows or
doors while the system is disarmed will sound
3 beeps at the keypad(s).
✴ READY KEY: Displays all open protection
zones.
# KEY: "Quick Arm" key permits ARMING of
the system without use of a security code (if
so programmed).
KEYS 0–9†: Used to enter your security code(s).
READY INDICATOR: (GREEN) Lit when the
system is ready to be armed (no faults present).
While the system is disarmed, this indicator will go
on and off as protection zones are closed and
opened.
N o t e : On some keypads there is, instead, a
POWER INDICATOR (GREEN) which is
lit when AC power is present. If the
indicator is off, the system may still be
operating, but on its backup battery
power. See Power Failure in TROUBLE
CONDITIONS section.
Keys 1 through 9 each perform their associated companion functions (OFF, AWAY, STAY, etc.)
when
preceded
by
an
entry
of
the
–8–
security
code
(as
described
later).
15. ARMED INDICATOR: (RED) Lit when
the system has been armed (STAY,
AWAY, INSTANT or MAXIMUM).
16. INTERNAL SOUNDER: The built-in
keypad sounder mimics the alarm
sounder during alarms, and will also
"beep" during certain system functions.
(see SUMMARY OF AUDIBLE/ VISUAL
NOTIFICATION).
17. EMERGENCY KEYS:
Individual keys A, B, and C (key D not
used).
On some keypads, these keys are not
present, and the following key pairs may
be available, instead, for emergency
functions:
1
2
5
AWAY
15
3
NO AC
14
4
ARMED
BYPASS NOT READY
ALARM STAY CHIME
FIRE CHECK INSTANT
BAT
READY
6
A
1
2
3
OFF
AWAY
STAY
4
5
6
MAX
TEST
BYPASS
7
8
9
INSTANT
CODE
CHIME
*
0
#
B
C
16
17
Some or all of these keys/pairs may be
programmed for panic functions by your
installer (see PANIC KEYS section).
8
11
9
STYLE B KEYPAD
IMPORTANT!: When entering codes and
commands, sequential key depressions must be
made within 2 seconds of one another. If 2 seconds
elapses without a key depression, the entry is
aborted and must be repeated from its beginning.
–9–
10
12
READY
PANIC
✴ &# , ✴ & 1 , # & 3
7
13
SECURITY CODES
General
Duress Code
Ask your installer if
"Duress" is active for
your system, and if so,
check here:
Quick Arming
Ask your installer if
"Quick Arming" is active
for your system, and if
At the time of installation, your installer programmed a personal four-digit
Master code, known only to you and yours. This code is used to perform
most system functions, including arming and disarming of the system. As an
additional safety feature, temporary user codes can be assigned (see next
page) for use by those not having a need to know the Master code. Note
that the Master code remains in effect even when other user codes are
assigned.
This feature is intended for use when you are forced to disarm or arm the
system under threat. When used, the system will act normally, but can
silently notify the central station of your situation, if that service has been
provided.
The Duress code is defined as user number 8.
Important: The Duress code is useful only when connected to a central
station.
If your system supports "Quick Arming", the "#" key can be pressed in
place of the security code when arming the system. The security code is
always required, however, when disarming the system. accept
so, check here:
–10–
(continued)
To Assign, Change, or
Delete
User Codes
4-DIGIT USER CODES
It is recommended that
obvious codes such as
1 1 1 1 or 1 2 3 4 not be
assigned.
SECURITY CODES
1. Enter your Master code and press the CODE key.
2. Enter single-digit user number ('2', '3', '4', '5', '6' or '7') for which a code
is to be assigned, changed, or deleted.
3. If assigning or changing a user's code, enter the desired 4-digit code
for use by that user number. The keypad will beep once.
If deleting a user's code, perform steps 1 & 2 and stop. In a few
moments the keypad will beep once, indicating that the existing code
has been deleted.
To assign your Duress code, do the following:
Enter your [Master code] + [8] + [8] + [desired 4-digit code]. The
keypad will beep once.
The Master code can be changed by the main user of the system. To
change it, do the following:
Enter your [Master code] + [8] + [1] + [new Master code] + [new Master
code] again. The keypad will beep once.
Important:Temporary users should not be shown how to use any
system function they do not need to know (e.g., bypassing protection
zones).
–11–
ENTRY/EXIT DELAYS
General Information
Your system has preset time delays, known as exit delay and entry delay.
When you arm your system, exit delay gives you time to leave through
the entry/exit door without setting off an alarm. Entry delay gives you time
to disarm the system when you reenter through the entry/exit door. The
system must be disarmed, however, before the entry delay period ends, or
an alarm will occur. The keypad will beep slowly during the entry delay
period, reminding you to disarm the system.
You can also arm the system with no entry delay at all by using either
INSTANT or MAXIMUM arming modes. These modes can provide greater
security while you are sleeping or while you are away for extended
periods of time.
See your installer for your delay times and record them here:
Exit Delay:
seconds
–12–
Entry Delay:
seconds
CHECKING FOR OPEN ZONES
Using the Before your system can be armed, all protected doors, windows and other
✴ READY Key protection zones must be closed or bypassed (see BYPASSING
PROTECTION ZONES section), otherwise the keypad will display a "Not
Ready" message, and if your keypad has a READY indicator light, it will
not be lit. The READY key can be used to display all faulted zones,
making it easier for you to secure any open zone.
To display faulted zones, simply press and release the READY key (do
not enter code first). Secure or bypass the zones displayed before arming
the system.
A "Ready" message will be displayed when all protection zones have
been either closed or bypassed and the keypad's READY indicator light (if
present) will be lit.
TYPICAL DISPLAYS
WHEN NOT READY TO ARM
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
INSTANT
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
TAMPER
TYPICAL DISPLAYS
INDICATING FAULTED PROTECTION ZONE
(AFTER PRESSING READY KEY)
03
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
INSTANT
–13–
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
TAMPER
TYPICAL DISPLAYS
INDICATING "READY TO ARM"
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
INSTANT
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
TAMPER
BYPASSING PROTECTION ZONES
Using the
6 BYPASS Key
LIMITATION
The system will not
allow fire zones to be
bypassed.
All bypasses are removed
when an OFF sequence
(security code plus OFF)
is performed.
This key is used when you want to arm your system with one or more
zones intentionally unprotected. The system must be disarmed first.
1. Enter your security code and press the BYPASS key.
2. Enter zone number(s) for the zone(s) to be bypassed (e.g., 06, 10,
13, etc.). Single digit zone numbers must be preceded by a zero (e.g.
05, 06).
3. When finished, the keypad will display a "Bypass" message along
with each bypassed zone number, accompanied by a beep for each.
Wait for these zones to be displayed, to confirm their bypass.
4. Arm the system as usual.
Bypassed zones are unprotected and will not cause an alarm if
violated while your system is armed.
TO BYPASS ZONES:
• ENTER USER CODE.
• PRESS BYPASS KEY.
• ENTER ZONE Nos.
• WAIT FOR BYPASSED ZONES
TO BE DISPLAYED.
• ARM BURGLARY PROTECTION
AS USUAL.
–14–
TYPICAL MOMENTARY DISPLAYS
OF BYPASSED ZONE
03
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
TAMPER
(continued)
BYPASSING PROTECTION ZONES
Quick Bypass
Ask your installer if
"Quick Bypass" is
active for your
system, and if so,
check here:
If your system supports "Quick Bypass", it allows you to easily bypass
all open (faulted) zones without having to enter zone numbers individually.
To use this feature, enter your security code, press the BYPASS key,
then stop. In a few moments, all open zones will be displayed along with a
"Bypass" message. Wait for all bypassed zones to be displayed, then
arm the system as usual.
TYPICAL DISPLAYS
"READY TO ARM WITH ZONES BYPASSED"
BURGLARY PROTECTION
CAN NOW BE ARMED
WITH ZONE(S) BYPASSED.
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–15–
TAMPER
ARMING PERIMETER ONLY
WITH ENTRY DELAY ON
Using the
3 STAY Key
BEFORE ARMING
close all doors and windows
(see CHECKING FOR OPEN
ZONES on page 13).
Use this key when you are staying inside, but expect someone t o
use an entry/exit door later.
1. Enter your security code and press the STAY key.
2. The keypad will beep three times and will display the armed message.
The red ARMED indicator will light.
3. The system will arm. An alarm will sound immediately if a protected
perimeter window or non-entry/exit door is then opened, but you may
otherwise move freely throughout the premises.
Later arrivals can enter through an entry/exit door without causing
an alarm, but they must disarm the system within the entry delay
period to avoid sounding an alarm.
USER CODE + STAY KEY
ARMS THE PERIMETER,
BUT ALLOWS USE OF
THE ENTRY/EXIT DOOR.
TYPICAL DISPLAYS
"ARMED STAY"
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–16–
TAMPER
ARMING PERIMETER ONLY
WITH ENTRY DELAY OFF
Using the
7 INSTANT Key
BEFORE ARMING
close all doors and windows
(see CHECKING FOR OPEN
ZONES on page 13).
Use this key when you are staying inside and do not expect
anyone to use an entry/exit door.
1. Enter your security code and press the INSTANT key.
2. The keypad will beep three times and will display the armed message.
The red ARMED indicator will light.
3. The system will arm. An alarm will sound immediately if any protected
perimeter door or window is then opened, but you may otherwise move
freely throughout the premises.
An alarm will sound immediately if anyone opens an entry/exit
door.
USER CODE + INSTANT KEY
ARMS THE PERIMETER
(INCLUDING THE ENTRY/EXIT DOOR),
WITH NO ENTRY DELAY.
TYPICAL DISPLAYS
"ARMED INSTANT"
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–17–
TAMPER
ARMING ALL PROTECTION
WITH ENTRY DELAY ON
Using the
2 AWAY Key
BEFORE ARMING
close all doors and windows
(see CHECKING FOR OPEN
ZONES on page 13).
Use this key when no one will be staying inside.
1. Enter your security code and press the AWAY key.
2. The keypad will beep twice and will display the armed message. The
red ARMED indicator will light.
3. You may leave through an entry/exit door during the exit delay period
without causing an alarm.
After exit delay, the system arms and will sound an alarm if a protected
window or non-entry/exit door is then opened, or if any movement is
detected inside your premises.
You may reenter through an entry/exit door, but must disarm the
system within the entry delay period to avoid an alarm.
USER CODE + AWAY KEY
ARMS ALL BURGLARY PROTECTION
(INTERIOR AND PERIMETER),
BUT ALLOWS USE OF THE
ENTRY/EXIT DOOR.
TYPICAL DISPLAYS
"ARMED AWAY"
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–18–
TAMPER
ARMING ALL PROTECTION
WITH ENTRY DELAY OFF
Using the
4 MAXIMUM Key
BEFORE ARMING
close all doors and windows
(see CHECKING FOR OPEN
ZONES on page 13).
Use this key when the premises will be vacant for extended
periods of time such as vacations, etc., or when no one will be moving
through protected interior areas.
1. Enter your security code and press the MAXIMUM key.
2. The keypad will beep twice and will display the armed message. The
red ARMED indicator will light.
3. You may leave through an entry/exit door during the exit delay period
without causing an alarm.
After exit delay, the system arms and will sound an alarm immediately if
any protected door or window is opened, or if any movement is
detected inside your premises.
An alarm will sound immediately, when someone reenters.
USER CODE + MAXIMUM KEY
ARMS ALL BURGLARY PROTECTION
(INTERIOR AND PERIMETER),
(INCLUDING THE ENTRY/EXIT DOOR
WITH NO ENTRY DELAY).
TYPICAL DISPLAYS
"ARMED MAXIMUM"
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
INSTANT
FIXED-WORD
–19–
TAMPER
DISARMING THE SYSTEM AND SILENCING ALARMS
Using the
1 OFF Key
IMPORTANT:
If you return and the
main burglary sounder
is on:
DO NOT ENTER, but
CONTACT THE POLICE
from a nearby safe location.
If you return after an
alarm has occurred and
the main sounder
has shut itself off:
the keypad will beep rapidly
upon your entering, indicating
that an alarm has occurred
during your absence
(the Memory of Alarm feature).
LEAVE IMMEDIATELY, and
CONTACT THE POLICE
from a nearby safe location.
WHEN SAFE TO DO SO,
re-enter
and follow the procedure
for silencing an alarm.
The OFF key is used to disarm the system and to silence alarm and
trouble sounds.
To Disarm the System
Enter your security code and press the OFF key. The "Ready" message
will be displayed, and the keypad will emit a single tone to confirm that the
system is disarmed.
To Silence a Burglary Alarm
SEE IMPORTANT NOTE AT LEFT!
Enter your security code and press the OFF key to silence the alarm (or
warning tones of a Memory of Alarm). Note the zone in alarm on the
keypad display, and make that zone intact (close door, window, etc.). Now
enter the security code plus OFF sequence again to clear the keypad's
Memory of Alarm display. If the display will not clear and does not provide
a "Ready" message, notify the alarm agency.
To Silence a Fire Alarm simply press the OFF key (the security code is not
needed to silence FIRE alarms). To then clear the keypad's Memory of
Alarm display, enter your security code and press the OFF key.
See page 29 for additional fire alarm information.
See the SUMMARY OF AUDIBLE/VISUAL NOTIFICATION section
for information which will help you to distinguish between FIRE
(Interrupted/Pulsed) and BURGLARY (Continuous/Steady) alarm
sounds.
–20–
USING THE KEYSWITCH
General
Arming
Disarming
Your
system may be equipped with a keyswitch for use when arming and
disarming. A single red light on the keyswitch plate indicates the status of
your system as follows:
OFF = Disarmed, Not Ready for Arming
SLOW FLASHING = Disarmed, Ready for Arming
RAPID FLASHING = Armed STAY or AWAY
To arm in the AWAY mode, turn key to right for 1/2 second.
To arm in the STAY mode, hold key turned to right for more than one
second.
The keypads will beep twice (AWAY mode) or 3 times (STAY mode) and
the keyswitch light will flash rapidly.
To disarm the system turn the key to the right and release.
If an alarm has occurred during the armed period, the keyswitch's light will
not flash on disarming (thus indicating memory of an alarm). With some
controls, turning the keyswitch key to the right a second time after disarming
can clear the alarm from memory, but it is advisable, instead, to refer to a
keypad to diagnose and clear any problem, and to subsequently clear
alarm memory. See the previous page for more about alarm memory.
–21–
CHIME MODE
Using the
9 CHIME Key
This feature can be used
only while the burglary
system is disarmed.
Your
system can be set to alert you to the opening of a door or window
while it is disarmed by using CHIME mode. When activated, three tones
will sound at the Keypad whenever a protected door or window is opened.
Pressing the READY key will display the open points.
To turn Chime Mode on, enter the security code and press the CHIME
key. The CHIME message will appear.
To turn Chime Mode off, enter the security code and press the CHIME
key again. The CHIME message will disappear.
PANIC KEYS
Using
Panic Keys
(for manually activating
silent and/or
audible alarms)
TO INITIATE A PANIC
FUNCTION AT ANY TIME
OF DAY OR NIGHT:
Press an active lettered key
for at least two seconds.
or
Press both keys of an active
pair at the same time.
* If connected
Your system may have been programmed to use special keys or combinations of keys to manually activate emergency (panic) functions. The
functions that might be programmed are: Silent Emergency, Audible
Emergency, Personal Emergency, and Fire.
A silent emergency will send a silent alarm signal to the central station*,
but there will be no audible alarms or visual displays.
An audible emergency will send a signal to the central station* and
sound a loud, steady alarm at your keypad(s) and at any external
sounders that may be connected (ALARM plus a zone number would also
be displayed).
A personal emergency alarm will send an emergency message to the
central station* and will sound at keypad(s), but not at external bells or
sirens.
A fire alarm will send a fire alarm message to the central station* and will
uniquely sound at keypad(s) and external bells and sirens (FIRE plus a
zone number would also be displayed).
–22–
PANIC KEYS
(continued)
A
LETTERED
EMERGENCY
KEYS
("D" IS
NOT USED)
<
B
C
STAY
1
2
3
MAX
TEST
BYPASS
4
5
6
INSTANT CODE
*
3 &#
PAIRED
CHIME
8
9
0
#
EMER
CHECK IF
ACTIVE
1 & *
> EMERGENCY
KEYS
READY
TYPICAL
KEYPAD
AND NOTE HERE
AWAY
7
D
SEE YOUR INSTALLER
OFF
* & #
PANIC
KEY(S)
P R O G R A M M E D
F U N C T I O N
ZONE
NUMBER
[A]
SILENT EMERGENCY (Fixed-Function)
95
[B]
____SILENT, ____AUDIBLE, ____PERSONAL, ____FIRE
07
[C]
AUDIBLE EMERGENCY (Fixed-Function)
96
95
OR
THE KEY(S) & FUNCTION(S)
[1] & [✴]
SILENT EMERGENCY (Fixed-Function)
PROGRAMMED
[✴] & [#]
____SILENT, ____AUDIBLE, ____PERSONAL, ____FIRE
07
FOR YOUR SYSTEM
[3] & [#]
AUDIBLE EMERGENCY (Fixed-Function)
96
• KEYS [A], [B], AND [C] ARE NOT PRESENT ON ALL KEYPADS.
• KEY [D], IF PRESENT ON YOUR KEYPAD, IS NOT ACTIVE HERE.
–23–
TESTING THE SYSTEM
TO BE CONDUCTED WEEKLY
Using the
5 TEST Key
NO ALARM REPORTS
WILL BE SENT TO THE
CENTRAL MONITORING
STATION
while
the
system is in Test mode.
The TEST key puts your system into Test mode, which allows each protection point to be checked for proper operation.
1. Disarm the system and close all protected windows, doors, etc. The
keypad's READY message should be displayed and the READY
indicator (if present) should be lit.
2. Enter your security code and press the TEST key.
3. The keypad will sound a single beep every 40 seconds as a reminder
that the system is in the test mode.
Each time a protection zone is faulted, the external siren or bell should
sound for one second and then turn off, while the keypad sounds 3 beeps.
If this does not happen, call for service immediately.
4. Open and close each protected door and window in turn and listen for
the required sounds The identification of each faulted protection point
should appear on the display.
5. Walk in front of any interior motion detectors (if used) and listen for the
required sound as movement is detected. The identification of the
detector should appear on the display when it is activated.
Note: Wireless PIR (Passive Infrared) units will send signals out only
if disturbed after they have been inactive for 3 minutes.
–24–
(continued)
TESTING THE SYSTEM
6. Follow the manufacturer's instructions to test all smoke detectors, to
ensure that all are functioning properly. The identification of each
detector should appear on the display when each is activated.
7. After all protection points have been checked and restored, there
should be no zone identification numbers displayed. If a problem is
experienced with any protection point (no confirming sounds,
no display), CALL FOR SERVICE IMMEDIATELY.
8. Turn off the Test mode by entering the security code and pressing the
OFF key.
–25–
TROUBLE CONDITIONS
"Check" and
"Battery" Displays
†
Not all systems use
wireless sensors.
The word CHECK on the keypad's display, accompanied by a "beeping"
at the keypad, indicates a trouble condition in the system.
To silence the beeping for these conditions, press any key.
1. A display of "CHECK" and one or more zone numbers indicates
that a problem exists with the displayed zone(s) and requires your
attention. If the CHECK display relates to a fire zone, CALL F O R
SERVICE IMMEDIATELY.
Determine if the zone(s) displayed are intact and make them so if they
are not. If the problem has been corrected, the display can be cleared if
you enter the OFF sequence (user code plus OFF key) twice. If the
display persists, CALL FOR SERVICE IMMEDIATELY.
2. If there are wireless sensors† in your system, the CHECK
condition may also be caused by some change in the environment that
prevents the receiver from hearing a particular sensor. CALL F O R
SERVICE IMMEDIATELY if this occurs.
TYPICAL "CHECK" DISPLAY
03
AWAY
BYPASS
STAY
ALARM
FIRE CHECK
INSTANT
FIXED-WORD
–26–
SUPV NO AC
PHONE TEST
NOT READY
CHIME BAT
TAMPER
(continued)
TROUBLE CONDITIONS
3. A display of "BAT" with no zone number or beeping indicates that
the main standby battery in your control is weak. If this condition
persists for more than one day (with AC present), CALL F O R
SERVICE.
4. A display of "BAT" with a zone number and a once per 40
seconds beeping at the keypad indicates that a low battery
condition exists in the wireless sensor displayed. Either replace the
battery yourself, or CALL FOR SERVICE. If the battery is not
replaced within 30 days, a CHECK display may occur.
Power Failure
If there is no keypad display at all, and the POWER indicator (if
present) is not lit, operating power for the system has stopped and the
system is inoperative. CALL FOR SERVICE IMMEDIATELY.
If the message "AC LOSS" or "NO AC" is displayed, and the
POWER indicator (if present) is off, the Keypad is operating on
battery power only. If only some lights are out on the premises, check circuit breakers and fuses and reset or replace as necessary. CALL F O R
SERVICE IMMEDIATELY if AC power cannot be restored.
– 27–
TROUBLE CONDITIONS
(continued)
Other Displays
dl:
If this remains displayed for more than 1 minute, your system is
disabled. CALL FOR SERVICE IMMEDIATELY.
CC: The system is in communication with the central station for change of
function or status verification. If this message persists for more
than 10 minutes, CALL YOUR SERVICE COMPANY.
FC: A communication failure has occurred. CALL FOR SERVICE
IMMEDIATELY.
O C The keypad is not receiving signals from the control panel and sees
an open circuit. If this message persists for more than 10 minutes,
CALL YOUR SERVICE COMPANY.
FOR SERVICING
INFORMATION,
SEE PAGE 43
– 28–
FIRE ALARM SYSTEM
IF INSTALLED
General
In Case Of Fire Alarm
Your fire alarm system (if installed) is on 24 hours a day, for continuous
protection. In the event of an emergency, the strategically located smoke
and heat detectors will automatically send signals to your system, triggering
a loud, interrupted sound from the Keypad. An interrupted sound will also
be produced by optional exterior sounders. A FIRE message will appear at
your Keypad and remain on until you silence the alarm.
1. Should you become aware of a fire emergency before your detectors
sense the problem, go to your nearest Keypad and manually initiate an
alarm by pressing the panic key pair assigned as FIRE emergency (if
programmed by the installer) as indicated on page 23.
2. Evacuate all occupants from the premises.
3. If flames and/or smoke are present, leave the premises and notify your
local Fire Department immediately.
4. If no flames or smoke are apparent, investigate the cause of the alarm.
The zone number(s) of the zone(s) in an alarm condition will be
displayed at the Keypad.
TYPICAL "FIRE EMERGENCY" DISPLAY
05
SUPV NO AC
ALARM
FIRE CHECK
PHONE TEST
NOT READY
CHIME BAT
INSTANT TAMPER
FIXED-WORD
–29–
(continued)
FIRE ALARM SYSTEM
IF INSTALLED
Silencing Fire Alarms
1. Silence the alarm by pressing the OFF key (security code not needed
to silence fire alarms). To clear the display, enter your code and press
the OFF key again (Memory of Alarm).
2. If the Keypad does not indicate a READY condition after the second
OFF sequence, press the READY key to display the zone(s) that are
faulted. Be sure to check that smoke detectors are not responding to
smoke or heat producing objects in their vicinity. Should this be the
case, eliminate the source of heat or smoke.
3. If this does not remedy the problem, there may still be smoke in the
detector. Clear it by fanning the detector for about 30 seconds.
4. When the problem has been corrected, clear the display by entering
your code and pressing the OFF key.
–30–
NATIONAL FIRE PROTECTION ASSOCIATION
RECOMMENDATIONS ON SMOKE DETECTORS
General
✪
KITCHEN
DINING
▲
With regard to the number and placement of smoke/heat detectors, we
subscribe to the recommendations contained in the National Fire Protection
Association's Standard #74 noted below.
Early warning fire detection is best achieved by the installation of fire
detection equipment in all rooms and areas of the premises as follows: A
smoke detector installed outside of each separate sleeping area, in the
immediate vicinity of the bedrooms and on each additional story of the
family living unit, including basements and excluding crawl spaces and
unfinished attics.
In addition, it is recommended that the owner consider the use of heat or
smoke detectors in the living room, dining room, bedroom(s), kitchen,
hallway(s), attic, furnace room, utility and storage rooms, basements and
attached garages.
✪
✪
BEDROOM BEDROOM
✪
TV ROOM
■
✪
✪
LIVING ROOM
BEDROOM
▲
KITCHEN
✪
DINING
■
LIVING ROOM
✪
■
✪
▲
BDRM
BDRM
BEDROOM
✪
■
✪
BEDROOM
✪
■
✪
BEDROOM
TO
BR
BEDROOM
■
▲
.
LVNG RM
■ Smoke Detectors for Minimum Protection
✪ Smoke Detectors for Additional Protection
▲ Heat-Activated Detectors
■
BASEMENT
–31–
▲
KTCHN
CLOSED
DOOR
GARAGE
EMERGENCY EVACUATION
Steps to Safety
PORCH
M
ET
OO
OS
DR
CL
BE
M
M
OO
OO
TH
DR
DR
BA
E
B
BE
2ND FLOOR
EN
CH
KIT
BACK DOOR
M
OO
DR
BE
M
OO
TH
DR
BA
BE
1ST FLOOR
•
•
BACK
•
FRONT
Establish and regularly practice a plan of escape in the event of fire. The
following steps are recommended by the National Fire Protection Association:
1. Plan on your detector or your interior and/or exterior sounders warning
all occupants.
2. Determine two means of escape from each room. One path of escape
should lead to the door that permits normal exit from the building. The
other may be a window, should your path be unpassable. Station an
escape ladder at such windows if there is a long drop to the ground.
3. Sketch a floor plan of the building. Show windows, doors, stairs and
rooftops that can be used to escape. Indicate escape routes for each
room. Keep these routes free from obstruction and post copies of the
escape routes in every room.
4. Assure that all bedroom doors are shut while you are asleep. This will
prevent deadly smoke from entering while you escape.
5. Try the door. If the door is hot, check your alternate escape route. If the
door is cool, open it cautiously. Be prepared to slam the door if smoke
or heat rushes in.
6. Crawl in the smoke and hold your breath.
7. Escape quickly; don't panic.
8. Establish a common meeting place outdoors, away from your premises,
where everyone can meet and then take steps to contact the authorities and account for those missing. Choose someone to assure that
nobody returns to the premises — many die going back.
–32–
QUICK GUIDE TO ALARM SYSTEM FUNCTIONS
FUNCTION
PROCEDURE
COMMENTS
Check Zones
Arm System
Press READY key.
Enter code. Press arming key desired:
(AWAY, STAY, INSTANT, MAXIMUM)
Press #. Press arming key desired:
(AWAY, STAY, INSTANT, MAXIMUM)
Enter code. Press BYPASS key.
Enter zone number(s) to be bypassed
(use 2-digit entries).
Enter code. Press BYPASS key.
To view faulted zones when system not ready.
Arms system in mode selected.
Enter code. Press OFF key.
Press OFF key.
Press any key.
Enter code. Press OFF key.
After disarming, enter code again.
Press OFF key again.
Enter user code 8 to arm or disarm "normally."
Also disarms system. Memory of alarm remains until cleared.
Memory of Alarm remains until cleared.
Determine cause. See Page 26.
Also silences sounders. Memory of alarm remains until cleared.
Keypad will beep rapidly upon entry if alarm has occurred.
Alarm display will remain upon disarming until cleared.
Quick Arm
(if programmed)
Bypass Zone(s)
Quick Bypass
(if programmed)
Silence Sounders
Burglary:
Fire:
"Check":
Disarm System
Clear Alarm
Memory
Duress
(if connected to
central station)
Panic Alarms
(as programmed)
Chime Mode
Test Mode
Press key [A], [B], or [C] for at least 2 sec., or
(if no A, B, or C on your keypad)
press keys [1]&[✴], or [✴]&[#], or [3]&[#],
both at same time.
To turn ON or OFF: Enter code. Press CHIME
key.
To turn ON: Enter code. Press TEST key.
To turn OFF: Enter code. Press OFF key.
Arms system in mode selected, quickly and without use of code.
Bypassed zones are unprotected and will not cause an alarm if violated.
Bypasses all faulted zones automatically.
Performs desired action and sends silent alarm to central station.
See Page 23 for functions programmed for your system.
Keypad will sound if doors or windows are violated while system is
disarmed and chime mode is ON.
Tests alarm sounder and allows sensors to be tested.
–33–
SUMMARY OF AUDIBLE/VISUAL NOTIFICATION
SOUND
CAUSE
DISPLAY
LOUD, INTERRUPTED†
Keypad & External
LOUD, CONTINUOUS†
Keypad & External
ONE SHORT BEEP
(not repeated)
Keypad only
FIRE ALARM
FIRE and ALARM are displayed; protection zone in alarm is displayed.
BURGLARY/AUDIBLE
EMERGENCY ALARM
a. SYSTEM DISARM
b. SYSTEM ARMING ATTEMPT
WITH AN OPEN ZONE
c. BYPASS VERIFY
ALARM is displayed; protection zone in alarm is also displayed.
ONE SHORT BEEP
(once every 40 seconds)
Keypad only
ONE BEEP every 40 sec.
Keypad only
SYSTEM IS IN TEST MODE
a. Only READY is displayed. Green READY indicator (if present) is lit.
b. NOT READY is displayed, open protection zone number is displayed.
Green READY indicator (if present) is not lit.
c. The bypassed protection zone numbers are displayed. (One beep for each number
displayed.) BYPASS displayed.
Opened Zone identifications will appear.
a. LOW BATTERY AT XMTR
b. TROUBLE
a. BAT displayed with ID number of transmitter.
b. CHECK displayed. Troubled protection zone is displayed.
TWO SHORT BEEPS
Keypad only
THREE SHORT BEEPS
Keypad only
ARM AWAY OR MAXIMUM
AWAY and (if MAXIMUM) INSTANT are displayed.
a. ARM STAY OR INSTANT
b. ZONE OPENED WHILE SYSTEM IS IN CHIME MODE
c. ZONE OPENED WHILE SYSTEM IS IN TEST MODE
MEMORY OF ALARM
a. STAY and (if INSTANT) INSTANT are displayed. Red ARMED indicator is lit.
b. CHIME displayed. Pressing ✳/ READY key will display opened zone.
ENTRY DELAY WARNING
None during delay; Exceeding the delay time without disarming causes alarm.
RAPID BEEPING
Keypad only
SLOW BEEPING
Keypad only
c. Open protection zone number is displayed.
FIRE and/or ALARM is displayed; zone in alarm is displayed.
†If
bell is used as external sounder, fire alarm is pulsed ring; burglary/audible emergency is steady ring.
N o t e s : • BAT displayed (with no beeping or zone number) indicates system main battery is weak (see page 27).
• Also see Power Failure, and Other Displays under TROUBLE CONDITIONS on page 27.
–34–
PROTECTION ZONES LIST
One or more sensing devices will have been assigned by the installer of your alarm system to each of the various
protection zones in your system (although not every zone number can be used). For example, the sensing device
on your Entry/Exit door may have been assigned to zone 06, sensing devices on windows in the master bedroom
to zone 10, and so on.
Zone numbers 07, 95 and 96 represent Keypad Keypad "Panic" alarm functions assigned by the installer (see
Page 23). Zone numbers 08 and 09 are reserved for Duress and Tamper signal reporting to the central station.
This chart may be used to record the specific zone number assignments for your system. Your installer will assist
you in recording this information.
Zone
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
Description
Key B (or: ✴ & #) Panic
–Duress–
–Tamper–
Zone
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
PROTECTION ZONE DESCRIPTIONS
Description
Zone Description
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
–35–
Zone
Description
51
52
53
54
55
56
57
58
59
60
61
62
63
95
Key A (or 1 & ✴) Panic
96
Key C (or 3 & #) Panic
–36–
OWNER'S INSURANCE PREMIUM
CREDIT REQUEST
This form should be completed and forwarded to your homeowner's insurance carrier for possible premium credit.
A . GENERAL INFORMATION:
Insured's Name and Address:__________________________________________________________________
__________________________________________________________________
Insurance Company:__________________________________ Policy No.: _____________________________
ADEMCO System:
Type of Alarm:
4110DL
4110XM (circle one)
Burglary
Fire
Both
Installed by: _________________________________ Serviced by: ___________________________________
name
name
_________________________________
___________________________________
address
address
B . NOTIFIES (Insert B for Burglary, F for Fire, where appropriate):
Local Sounding Device ________
Police Dept. _______
Fire Dept. ______
Central Station _________
Name and Address:__________________________________________________________________________
C . POWERED BY: A.C. With Rechargeable Power Supply
D . TESTING:
Quarterly,
Monthly,
Weekly,
Other _______________________________
continued on other side
–37–
OWNER'S INSURANCE PREMIUM
CREDIT REQUEST (cont.)
E . SMOKE DETECTOR LOCATIONS:
Furnace Room
Kitchen
Bedrooms
Attic
Basement
Living Room
Dining Room
Hall
All Exterior Doors
F . BURGLARY DETECTING DEVICE LOCATIONS:
Front Door
Basement Door
Rear Door
1st Floor Windows
All windows
Interior Locations
All Accessible Openings, Including Skylights, Air Conditioners and Vents
G . ADDITIONAL PERTINENT INFORMATION:
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
_________________________________________________________________________________________
Signature: ____________________________________________________ Date: _______________________
–38–
CANADIAN DEPARTMENT OF COMMUNICATIONS (DOC) STATEMENT
NOTICE
AVIS
The Canadian Department of Communications label identifies
certified equipment. This certification means that the equipment
meets certain telecommunications network protective, operational
and safety requirements. The Department does not guarantee the
equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is
permissible to be connected to the facilities of the local
telecommunications company. The equipment must also be
installed using an acceptable method of connection. In some
cases, the company's inside wiring associated with a single line
individual service may be extended by means of certified
connector assembly (telephone extension cord). The customer
should be aware that compliance with the above conditions may
not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized
Canadian maintenance facility designated by the supplier. Any
repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications
company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical
ground connections of the power utility, telephone lines and
internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural
areas.
Caution: User should not attempt to make such connections
themselves, but should contact the appropriate electric inspection
authority, or electrician, as appropriate.
The Load Number (LN) assigned to each terminal device denotes
the percentage of the total load to be connected to a telephone loop
which is used by the device, to prevent overloading. The
termination on a loop may consist of any combination of devices
subject only to the requirement that the total of the Load Numbers
of all the devices does not exceed 100.
L'étiquette du ministère des Communications du Canada identifie le matériel
homologué. Cette étiquette certifie que le matériel est conforme à certaines
normes de protection, d'exploitation et de sécurité des réseaux de
télécommunications. Le ministère n'assure toutefois pas que le matériel
fonctionnera à la satisfaction de l'utilisateur.
Avant d'installer ce matériel, l'utilisateur doit s'assurer qu'il est permis de le
raccorder aux installations de l'entreprise locale de télécommunications. Le
matériel doit également être installé en suivant une méthode acceptée de
raccordement. Dans certains cas, les fils intérieurs de l'entreprise utilisés
pour un service individuel à la ligne unique peuvent être prolongés au moyen
d'un dispositif homologué de raccordement (cordon prolongateur
téléphonique interne). L'abonne ne doit pas oublier qu'il est possible que la
conformité aux conditions énoncées ci-dessus n'empèche pas la dégradation
du service dans certaines situations. Actuellement, les entreprises de
télécommunications ne permettent pas que l'on raccorde leur matériel aux
prises d'abonnés, sauf dans les cas precis prévus par les tarifs particuliers
de ces entreprises.
Les réparations du matériel homologué doivent être effectuées pas un centre
d'entretien canadien autorisé désigné par le fournisseur. La compagnie de
télécommunications peut demander à l'utilisateur de débrancher un appareil
à la suite de réparations ou de modifications effectuées par l'utilisateur ou à
cause de mauvais fonctionnement.
Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise
en terre de la source d'énergie électrique, des lignes téléphoniques de
réseau de conduites d'eau, s'il y en a, soient raccordés ensemble. Cette
précaution est particulièrement importante dans les régions rurales.
Avertissement: L'utilisateur ne doit pas tenter de faire ces raccordements
lui-même; il doit avoir recours à un service d'inspection des installations
électriques, ou à un électricien, selon le cas.
L'indice de charge (IC) assigné à chaque dispositif terminal pour éviter toute
surcharge indique le pourcentage de la charge totale qui peut être raccordé à
un circuit téléphonique fermé utilisé par ce dispositif. La terminaison du
circuit fermé peut être constituée de n'importe quelle combinaison de
dispositifs, pourvu que la somme des indices de charge de l'ensemble des
dispositifs ne dépasse pas 100.
–39–
UL NOTICE: This is a "Grade A" Residential System.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 15 STATEMENT
This equipment has been tested to FCC requirements and has been found acceptable for use. The FCC requires the following
statement for your information:
This equipment generates and uses radio frequency energy and if not installed and used properly, that is, in strict accordance
with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested and
found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules,
which are designed to provide reasonable protection against such interference in a residential installation. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• If using an indoor antenna, have a quality outdoor antenna installed.
• Reorient the receiving antenna until interference is reduced or eliminated.
• Move the radio or television receiver away from the receiver/control.
• Move the antenna leads away from any wire runs to the receiver/control.
• Plug the receiver/control into a different outlet so that it and the radio or television receiver are on different branch circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions. The
user or installer may find the following booklet prepared by the Federal Communications Commission helpful:
"Interference Handbook"
This booklet is available from the U.S. Government Printing Office, Washington, DC 20402.
The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or
User's Manual. Unauthorized changes or modifications could void the user's authority to operate the equipment.
FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT
This equipment complies with Part 68 of the FCC rules. On the front cover of this equipment is a label that contains, among
other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company.
This equipment uses the following jacks:
An RJ31X is used to connect this equipment to the telephone network.
The REN is used to determine the quantity of devices which may be connected to the telephone line. Excessive RENs on the
telephone line may result in the devices not ringing in response to an incoming call. In most, but not all areas, the sum of the
RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to the line, as determined by
the total RENs, contact the telephone company to determine the maximum REN for the calling area.
(continued)
–40–
(continued) FEDERAL COMMUNICATIONS COMMISSION (FCC) Part 68 STATEMENT
If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. If advance notice is not practical, the telephone company will notify the customer as
soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact the manufacturer for repair and warranty information. If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.
There are no user serviceable components in this product, and all necessary repairs must be made by the manufacturer.
Other repair methods may invalidate the FCC registration on this product.
This equipment cannot be used on telephone company-provided coin service. Connection to Party Line Service is subject to
state tariffs.
This equipment is hearing-aid compatible.
When programming or making test calls to an emergency number, briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak hours; such as early morning or late evening.
IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS
If your security system has been connected to the telephone line, and there is trouble with regular telephone service,
disconnect the security system from the telephone line by removing the plug from the RJ31X (CA38A in Canada) telephone
wall jack (you should have been shown how to do this by your installing company). Do not attempt to disconnect the telephone
line connection inside the control cabinet. Doing so will result in the COMPLETE disruption of your regular telephone service.
If the regular phone works correctly after the plug has been disconnected from the RJ31X wall jack, the security system has a
problem and you should call your service representative for service immediately. If, upon disconnection of the security
system from the wall jack, there is still a problem with telephone service, notify the telephone company that they have a
problem and request prompt repair service.
IMPORTANT: A security system connected to an alarm monitoring station relies on that connection.
• If the security system is at fault, reinsert the plug as soon as the security system is repaired.
• If the phone service is at fault, re-insert the plug immediately, to ensure resumption of full protection upon
restoration of phone service.
The user may not, under any circumstances (in or out of warranty), attempt any service or repairs to the system.
–41–
WARNING!
THE LIMITATIONS OF THIS ALARM SYSTEM
While this system is an advanced design security system, it does not offer guaranteed protection against burglary or fire or
other emergency. Any alarm system, whether commercial or residential, is subject to compromise or failure to warn for a variety of reasons. For example:
• Intruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or
disconnect an alarm warning device.
• Intrusion detectors (e.g. passive infrared detectors), smoke detectors, and many other sensing devices will not work without power. Battery operated devices will not work without batteries, with dead batteries, or if the batteries are not put in
properly. Devices powered solely by AC will not work if their AC power supply is cut off for any reason, however briefly.
• Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver. Even if the
signal path has been recently checked during a weekly test, blockage can occur if a metal object is moved into the path.
• A user may not be able to reach a panic or emergency button quickly enough.
• While smoke detectors have played a key role in reducing residential fire deaths in the United States, they may not activate
or provide early warning for a variety of reasons in as many as 35% of all fires, according to data published by the Federal
Emergency Management Agency. Some of the reasons smoke detectors used in conjunction with this System may not work
are as follows. Smoke detectors may have been improperly installed and positioned. Smoke detectors may not sense fires
that start where smoke cannot reach the detectors, such as in chimneys, in walls, or roofs, or on the other side of closed
doors. Smoke detectors also may not sense a fire on another level of a residence or building. A second floor detector, for
example, may not sense a first floor or basement fire. Moreover, smoke detectors have sensing limitations. No smoke detector can sense every kind of fire every time. In general, detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed, violent explosions, escaping gas, improper storage of flammable materials,
overloaded electrical circuits, children playing with matches, or arson. Depending upon the nature of the fire and/or the locations of the smoke detectors, the detector, even if it operates as anticipated, may not provide sufficient warning to allow
all occupants to escape in time to prevent injury or death.
• Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation
manual. Passive Infrared Detectors do not provide volumetric area protection. They do create multiple beams of protection,
and intrusion can only be detected in unobstructed areas covered by those beams. They cannot detect motion or intrusion
that takes place behind walls, ceilings, floors, closed doors, glass partitions, glass doors, or windows. Mechanical tampering, masking, painting or spraying of any material on the mirrors, windows or any part of the optical system can reduce their
detection ability. Passive Infrared Detectors sense changes in temperature; however, as the ambient temperature of protected area approaches the temperature range of 90° to 105°F (32° to 40°C), the detection performance can decrease.
(continued)
–42–
(continued) WARNING! THE LIMITATIONS OF THIS ALARM SYSTEM
• Alarm warning devices such as sirens, bells or horns may not alert people or wake up sleepers if they are located on the
other side of closed or partly open doors. If warning devices sound on a different level of the residence from the bedrooms,
then they are less likely to waken or alert people inside the bedrooms. Even persons who are awake may not hear the warning if the alarm is muffled from a stereo, radio, air conditioner or other appliance, or by passing traffic. Finally, alarm warning
devices, however loud, may not warn hearing-impaired people or waken deep sleepers.
• Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or
temporarily out of service. Telephone lines are also subject to compromise by sophisticated intruders.
• Even if the system responds to the emergency as intended, however, occupants may have insufficient time to protect
themselves from the situation. In the case of a monitored alarm system, authorities may not respond appropriately.
• This equipment, like other electrical devices, is subject to component failure. Even though this equipment is designed to
last as long as 10 years, the electronic components could fail at any time.
The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance. This
alarm system should be tested weekly to make sure all sensors and transmitters are working properly.
Wireless transmitters (used with some systems) are designed to provide long battery life under normal operating conditions.
Longevity of batteries may be as much as 4 to 7 years, depending on the environment, usage, and the specific wireless device being used. External factors such as humidity, high or low temperatures, as well as large swings in temperature, may all
reduce the actual battery life in a given installation. This wireless system, however, can identify a true low battery situation,
thus allowing time to arrange a change of battery to maintain protection for that given point within the system.
Installing an alarm system may make one eligible for lower insurance rates, but an alarm system is not a substitute for insurance. Homeowners, property owners and renters should continue to act prudently in protecting themselves and continue to
insure their lives and property.
We continue to develop new and improved protection devices. Users of alarm systems owe it to themselves and their loved
ones to learn about these developments.
SERVICING INFORMATION
Your local authorized service representative is the person best qualified to service your alarm system.
Arranging a regular program with that person is advisable. Your local service representative is:
NAME:_____________________________________________ PHONE: __________________________
ADDRESS:_______________________________________________________________________________
_______________________________________________________________________________
–43–
ADEMCO ONE YEAR LIMITED WARRANTY
Alarm Device Manufacturing Company, a Division of Pittway Corporation, and its divisions, subsidiaries and affiliates ("Seller"),
165 Eileen Way, Syosset, New York 11791, warrants its security equipment (the "product") to be free from defects in materials
and workmanship for one year from date of original purchase, under normal use and service. Seller's obligation is limited to repairing or replacing, at its option, free of charge for parts, labor, or transportation, any product proven to be defective in materials or workmanship under normal use and service. Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than the Seller. In case of defect, contact the security professional who installed and maintains your security equipment or the Seller for product repair.
This one year Limited Warranty is in lieu of all other express warranties, obligations or liabilities. THERE ARE NO EXPRESS
WARRANTIES, WHICH EXTEND BEYOND THE FACE HEREOF. ANY IMPLIED WARRANTIES, OBLIGATIONS OR LIABILITIES
MADE BY SELLER IN CONNECTION WITH THIS PRODUCT, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY,
OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR
FROM THE DATE OF ORIGINAL PURCHASE. ANY ACTION FOR BREACH OF ANY WARRANTY, INCLUDING BUT NOT LIMITED
TO ANY IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 12 MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES
FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY
WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER'S OWN NEGLIGENCE OR FAULT. Some
states do not allow limitation on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
Seller does not represent that the product may not be compromised or circumvented; that the product will prevent any personal
injury or property loss by burglary, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or
protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery,
fire or other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that
there will be no personal injury or property loss as a result. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING. HOWEVER, IF SELLER IS HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OR ORIGIN, SELLER'S MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, WHICH SHALL BE THE COMPLETE
AND EXCLUSIVE REMEDY AGAINST SELLER. This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. No increase or alteration, written or verbal, to this warranty is authorized.
A Division of Pittway Corporation
165 Eileen Way, Syosset, New York 11791
Copyright © 1996 PITTWAY CORPORATION
àN5100V5Bä
N5100V5 Rev B 4/99