Installation Guide (English) - cs.psn

SW274_IG.book
Page 1
Friday, September 15, 2017
9:21 PM
Model No.
Installation Guide
Model Name
Model No.
Wireless Video Intercom System
VL-SW274
Main Monitor Station
VL-MW274
R This guide is for use with the above 2 models.
VL-V522L
VL-MW274
Door station
Main monitor station
R The Installation Guide in Indonesian can be accessed from the following site:
https://panasonic.net/cns/pcc/support/intercom/sw274
R Door station is described as "doorphone" and Main monitor station is described as "main
monitor" in this guide.
R In this guide, the suffix of each model number (e.g., the "BX" in "VL-SW274BX") is omitted
unless necessary.
Note to the installer
R Before attempting to connect or operate this product, please read the label on the rear of
the doorphone and the main monitor/extension monitor.
R Please read this guide carefully, and install the product safely and correctly by following
the instructions. Carefully read the information found in the section titled "For your
safety" in particular.
R Only use attachments/accessories specified by the manufacturer.
R The installation shall be carried out in accordance with all applicable installation rules.
R To the maximum extent permitted by law, Panasonic assumes no responsibility for
injuries or property damage resulting from failures arising out of improper installation or
operation inconsistent with this document.
R After installation, make sure to leave this guide with the customer.
SW274_IG.book
Page 2
Friday, September 15, 2017
9:21 PM
For your safety
To prevent severe injury and loss of life/
property, read this section carefully
before using the product to ensure
proper and safe operation of your
product.
WARNING
Preventing fire, electric shock and
short circuits
Leave installation work to the
dealer. Installation work requires
technique and experiences. Failure
to observe this may cause fire,
electric shock, injury, or damage to
the product. Consult the dealer.
RElectrical connection work should
be performed by certified personnel
only. Certification is required for
performing electrical connection
work. Consult your dealer.
RDo not attempt to disassemble or
modify this product. Contact an
authorised service centre for repairs.
RNever install wiring during a lightning
storm.
RDo not connect non-specified devices.
RWhen opening holes in walls for
installation or wiring, or when securing
the power cable, make sure you do not
damage existing wiring and ductwork.
RDo not make any wiring connections
when the power supply is turned on.
RDo not install the main monitor/
extension monitor in the following
places:
– Places where the main monitor/
extension monitor may be splashed
with water or chemicals.
R
2
– Places where there is a high
concentration of dust, or high
humidity.
RDo not perform any actions (such as
fabricating, twisting, stretching,
bundling, forcibly bending, damaging,
altering, exposing to heat sources, or
placing heavy objects on the power
cable) that may damage the power
cable. Using the product with a
damaged power cable may cause
electric shock, short circuits, or fire.
Contact an authorised service centre
for repairs.
RWhen existing wires are used, it is
possible that they contain AC voltage.
Contact an authorised service centre.
Preventing accidents and injuries
Do not install or use the product in
health care facilities if any regulations
posted in the area instruct you not to
do so. Hospitals or health care
facilities may be using equipment that
could be sensitive to external RF
(radio frequency) energy.
R Do not install or use this product near
automatically controlled devices such
as automatic doors and fire alarms.
Radio waves emitted from this product
may cause such devices to
malfunction, resulting in an accident.
R
CAUTION
Preventing electric shock
If the wiring is underground, do not
make any connections underground.
RIf the wiring is underground, use a
protection tube.
R If the wiring is outdoors, use a
protection tube or a surge protector.
R
SW274_IG.book
Page 3
Friday, September 15, 2017
Preventing injury
R
Install the product securely adhering
to the instructions in this guide to
prevent it from falling off the wall.
Avoid installing onto low-strength
9:21 PM
walls, such as gypsum board, ALC
(autoclaved lightweight concrete),
concrete block, or veneer (less than
18 mm thick) walls.
Supplied accessories for installation
For the doorphone*1
Screw × 2
(3.8 mm × 20 mm)
For the main monitor/extension monitor
Screw × 2
(4 mm × 16 mm)
Mounting bracket × 1
Important:
R You will need the following additional items to install and configure the doorphone and the
main monitor/extension monitor.
[Locally procured]
– Wires (for doorphone and other connections):
Prepare wires of the appropriate specification. (a"Wire type and length")
Note:
R The illustrations in the supplied manual(s) may vary slightly from the actual product.
*1 VL-SW274 model only
3
SW274_IG.book
Page 4
Friday, September 15, 2017
9:21 PM
Precautions for installation
To avoid malfunction or communication disturbances, do not install the doorphone or the main monitor/
extension monitor in the following locations:
– Places where vibration or any other kind of impact occurs.
– Places where echoing is frequent.
– Places near a high concentration of dust, hydrogen sulphide, ammonia, sulphur, or noxious fumes.
For the doorphone
R If a strong light is shining on the doorphone, the visitor’s face may not be distinguishable. Do not place
the doorphone in the following locations:
– Where most of the background is the sky.
– Where the background is a white wall, and direct sunlight will reflect off it.
– Where direct sunlight will shine on the doorphone.
R Do not place the doorphone in locations where echoing occurs, as this will cause the doorphone to
beep frequently.
R Make sure the rear of the doorphone is not subject to water.
R Depending on the installation location, condensation may form on the doorphone’s lens cover. This
may cause images to become obscured. Condensation will dissipate as the temperature rises.
For the main monitor/extension monitor
R Install the main monitor away from electronic appliances such as TVs, radios, personal computers, air
conditioners, boiler control panels with intercom, home security equipment, wireless devices, or digital
cordless phones.
R Do not install the main monitor/extension monitor in places where it will be affected by extremely highfrequency radio waves (near broadcasting antennas etc.). This may cause the display to flicker or an
interrupting noise to occur.
R Leave at least 20 cm of space above, below, and to the left and right sides of the main monitor/
extension monitor. Do not install on a wall that is deeply recessed.
R Do not install the main monitor/extension monitor inside a wall.
R Be sure to install the main monitor/extension monitor more than 5 m away from the doorphone.
R The product operates in the frequency range of 2.4 GHz and 2.48 GHz with a peak transmission power
of 100 mW (max.). Refer to the "For best performance" section in the Operating Instructions.
R In areas surrounded by a high electrical field, disturbances may occur in the main monitor’s/extension
monitor’s image or sound.
4
SW274_IG.book
Page 5
Friday, September 15, 2017
9:21 PM
Wiring schematic diagram
Set up correctly according to the following wiring schematic diagram and "Wire type and length".
R For information, such as order numbers, about optional devices that can be connected to, refer to the
"Additional/replacement accessories" section in the Operating Instructions.
DOORPHONE 1
DOORPHONE 2
You can also connect an
optional lobby station or Video
Intercom System for Apartment
Complexes. (See page 7.)
MAIN MONITOR
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
NP
D1
D2
D3
D4
Ml-1
Ml-2
MO-1
MO-2
MO-3
MO-4
MO-5
MO-6
IN1
IN2
IN3
IN4
P1
P2
NP
NP
5 Ml-1
6 Ml-2
EXTENSION
MONITOR 1
5 Ml-1
6 Ml-2
EXTENSION
MONITOR 2
5 Ml-1
6 Ml-2
EXTENSION
MONITOR 3
NP
NP
NP
NP
NP
19
20
21
22
S1
S2
S3
S4
Connection device
for option Input
(A contact) *1
NP
Terminal box
(4-conductor
wiring)
NP
1
Power plug
(220-240 V AC)
Electric Electric
lock
lock
1
PBX
NP: Non-polarised
A Power supply
*1 Connection devices for option input (A contact) can be used when a VL-V900 and VL-V700 series
Video Intercom System for Apartment Complexes is used.
– Make sure to connect emergency terminals to the IN1/IN2 terminals.
– Make sure to connect doorbells to the IN3/IN4 terminals. A doorbell and doorphone 2 cannot be
used together.
5
SW274_IG.book
Page 6
Friday, September 15, 2017
9:21 PM
Wire type and length
Wire type*1
Wiring run
Diameter
Doorphone –
Main monitor –
Extension monitor*2
Main monitor –
Electric lock*3
Main monitor –
Connection device for
option input (A contact)*3
Main monitor –
PBX
Length (Max.)
ø 0.65 mm
22 AWG
100 m
ø 1.0 mm
18 AWG
130 m
ø 0.5 mm
CAT 5
50 m
ø 0.5 mm - ø 1.2 mm
(24 AWG - 17 AWG)
According to the
specifications of the
connected device.
ø 0.5 mm - ø 1.2 mm
(24 AWG - 17 AWG)
According to the
specifications of the
connected device.
ø 0.65 mm
CAT 3 or 22 AWG
100 m
*1 Type: Single-pair cable with outer sheath (jacket)
Conductor: Copper solid
R A certified power supply wiring has to be used with this equipment. The relevant national
installation and/or equipment regulations shall be considered. A certified power supply wiring not
lighter than ordinary polyvinyl chloride flexible wiring according to IEC 60227 shall be used.
*2 When an extension monitor is used, make sure that the total wiring length from the doorphone to the
main monitor and then to the extension monitor, is within about 100 m.
*3 When using an electric lock or a connection device for option input (A contact), select a device that
meets the following guidelines:
R Electric lock connection terminal (S1/S2, S3/S4):
– N/O dry closure contact
– 30 V AC (1 A)/24 V DC (1 A) or lower
R Connection device for option input (A contact) terminal (IN1/IN2/IN3/IN4):
– Input method: No-voltage contact
– Open-circuit voltage between terminals: DC 7 V or less
– Detection definite time: 0.1 second or more
– Short-circuit between terminals: 5 mA or less
– Resistance value: make: 500 Ω or less, break: 15 KΩ or more
6
SW274_IG.book
Page 7
Friday, September 15, 2017
9:21 PM
„ Connecting an optional lobby station
VL-V591 Lobby station
MAIN MONITOR
<Rear view>
NP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
D1
D2
D3
D4
Ml-1
Ml-2
MO-1
MO-2
MO-3
MO-4
MO-5
MO-6
IN1
IN2
IN3
IN4
P1
P2
NP
19
20
21
22
S1
S2
S3
S4
NP: Non-polarised
<Be sure to perform the following to ensure proper operation>
R Connecting an optional VL-V591 lobby station
– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the lobby station.
– Connect terminal S1/S2 on the main monitor with terminal S1/S2 on the lobby station.
– After connecting to the main monitor, change the [Lobby connection] setting to [Connected devices]
using the main monitor. (→Operating Instructions of the Video Intercom System.)
R Connection for VL-V900 and VL-V700 series Video Intercom System for Apartment Complexes
– Connect terminal D1/D2 on the main monitor with terminal D1/D2 on the VL-V701 Distribution Box.
Note:
R For information about connections, refer to the documentation of the VL-V591 or VL-V900 and VLV700 series.
7
SW274_IG.book
Page 8
Friday, September 15, 2017
9:21 PM
Doorphone installation position
Installation position of the doorphone and camera range
Views when the camera is facing forwards at 0° (default).
R Example: Installation height is 1450 mm (standard position).
(Units: mm)
B
A
A view when looking
from above
G
C
I
F
D
H
K
J
E
A Image range B Approx. 66° C Centre of doorphone D Approx. 1450 E Approx. 500
F Approx. 1810 G Approx. 650 H Approx. 1160 I Image range: Approx. 960 J Approx. 87°
K Approx. 500
The camera angle can be adjusted using the camera angle control lever on the rear of the
doorphone (step 3, “Installing the doorphone”), so that the image range can be changed.
Side view when the camera is installed
lower than the standard position, and
facing upwards at 15°.
Top view when the camera is facing left or
R Example: Installation height is 1100 mm.
R Example: Camera angle faces left 15°.
right at 15° *1.
(Units: mm)
A
B
I
G
C
F
D
H
K
J
L
M
E
A Image range B Approx. 66° C Centre of doorphone D Approx. 1100 E Approx. 500
F Approx. 1690 G Approx. 710 H Approx. 980 I Image range: Approx. 1080 J Approx. 270
K Approx. 810 L Approx. 87° M Approx. 500
*1 If the camera points 15° upwards, the left or right angle is less than 7°.
Note:
The measurements and angles are for reference purposes and may vary depending on the environment.
8
SW274_IG.book
Page 9
Friday, September 15, 2017
9:21 PM
Installing the doorphone
Important:
R On the bottom surface of the doorphone and the
mounting base, there are holes to allow water to
drain. Do not cover them up when installing.
R When existing wiring (such as chime wires) is
used:
– It may contain AC voltage that may cause
electric shock and/or damage the product.
– Never use the following types of wiring.
Consult a qualified technician/dealer.
2
R Before drilling, refer to “Precautions for
installation” for installation location.
*1
B
A
D
C
R See "Wire type and length" for information about
wiring materials.
1
Attach the mounting base (A) to the wall
securely using the wood screws (B)
(accessory).
R Install the mounting base on a vertical flat
wall.
C Wire (locally procured)
D 83.5 mm
*1 To prevent dew condensation, fill a hole for
wiring as much as possible.
Remove the mounting base.
A Open the screw cover (A).
A
3
B
B Screwdriver
B Loosen the mounting screw (C).
Adjust the camera angle using the camera
angle control lever.
A
Rear view
B
C
C
D
D
E
A Camera angle control lever
B Left (maximum 15°)
C Right (maximum 15°)
D Upwards (maximum 15°)
D Water drain holes
E Mounting base
9
SW274_IG.book
Page 10
Friday, September 15, 2017
Examples of camera angle
Facing forwards
Facing upwards
Facing left
9:21 PM
B Mount the doorphone to the mounting
base. Fasten the screw, then close the
screw cover (C).
Facing upper left
C
R The angle can also be adjusted to the right
or upper right.
Important:
R When the camera angle is adjusted to the
upper left or upper right, the image may be
slightly distorted.
4
Connect the wire, then mount the doorphone
to the mounting base.
A Unscrew the screws.
Push in the wire to the terminal connectors
(non polar), then tightly fasten the screws
(A).
A – Recommended torque: 0.5 N·m
{5.1 kgf·cm}
– Maximum torque: 0.7 N·m {7.1
kgf·cm}
A
B
B Wire (connecting to the main monitor)
10
SW274_IG.book
Page 11
Friday, September 15, 2017
9:21 PM
Main monitor/extension
monitor installation position
Installing the main monitor/
extension monitor
About the installation position of the main
monitor/extension monitor and mounting
bracket
R Place the main monitor/extension monitor in a
location that your eyes are the same height as
the centre of the display.
R For the following reasons, leave at least 20 cm
(A) of space above, below, and to the left and
right sides of the main monitor/extension
monitor:
– To prevent malfunction and sound cutting out
– To ensure to make sure the reset button (B)
can be used (the reset button is on the bottom
of the main monitor/extension monitor)
1
A
B
D
E
C
H
F
G
C Screws (accessory)
D Hole in wall E 60 mm F 83.5 mm
G 7 mm H 50 mm
1
1
2
1
1
Attach the mounting bracket (A) to the wall
securely.
R Install the mounting bracket on a vertical flat
wall (B).
Connect the wires.
R Connect the wires correctly according to
"Wiring schematic diagram".
2
R After deciding where to install the main monitor/
extension monitor, attach the mounting bracket
in the location shown below.
D
C
E
C Main monitor/extension monitor installation
position
D 121.5 mm
E 58 mm
R How to make wiring connections
While pressing on the button (A) with a
pointed object such as a screwdriver, insert
the wire into the terminal connector (B). (To
disconnect a wire, while pressing on the
button (A), pull out the wire.)
B
A
C
D
C Bare wire at tip 9 mm
D Wiring from doorphone or other device
11
SW274_IG.book
Page 12
Friday, September 15, 2017
Important:
Do not connect the power cable.
(Damage may occur.)
3
Mount the main monitor/extension monitor to
the mounting bracket.
3-1 Line up the tab on the bottom of the
bracket with the groove on the main monitor/
extension monitor.
3-2 Line up the tab on the top of the bracket
with the groove on the main monitor/extension
monitor, and push the main monitor/extension
monitor down until it is secure.
12
9:21 PM
SW274_IG.book
Page 13
Friday, September 15, 2017
9:21 PM
Notes
13
SW274_IG.book
Notes
14
Page 14
Friday, September 15, 2017
9:21 PM
SW274_IG.book
Page 15
Friday, September 15, 2017
9:21 PM
Notes
15
SW274_IG.book
Page 14
Friday, September 15, 2017
9:21 PM
1006, Oaza Kadoma, Kadoma-shi, Osaka 571-8501, Japan
http://www.panasonic.com
© Panasonic Corporation 2017
PNQX8614ZA C0917MM0
Download PDF