Introduction
Backlit LCD Display
Introduction
Making Life Easier and Safer
Product Features
Features
Staying in touch with your family and friends is
convenient and easy when using your microTALK® radio.
Some of the many uses you will discover include:
Owner’s Manual
15
16
Communicating with others while hiking, biking, and working; keeping
track of family and friends at a crowded public event; checking with
travel companions in another car; talking with neighbors; arranging
meeting spots with others while shopping at the mall.
1
Secure your microTALK radio while on
the go.
®
Belt Clip
2
11
Nothing Comes Close to a Cobra
Battery Low
Listening for a Response
Listening
If there are no transmissions within 10 seconds, the
radio will automatically switch to Battery Save mode
and the Power Saver icon will flash in the display.
This will not affect the radio’s ability to receive
incoming transmissions.
Volume Level
Two Inches (5 cm)
from Mouth
4
• Speaker/
Microphone/
Charge Jack
19
20
• Roger Beep
Selectable On/Off
1. Antenna
2. External Speaker/
Microphone/ USB Charge Jack
3. Mode/Power Button
4. Call/Lock Button
5. Channel Up/Down Buttons
6. Backlit LCD Display
7. Speaker/Microphone
8. Volume Up/Down Buttons
9. LED Light Button
10. Talk Button
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
Memory/Escape Button
Tri-Watch Button
Scan Button
Hi/Med/Low Button
Wrist Strap Connection
Belt Clip
Battery Compartment
Battery Door Screws (2)
Rubberized Grips
LED Flashlight
Weather Button
• Keystroke Tones
• Battery Level
Indicator
• Auto Squelch
• Belt Clip
A-2
A-3
LED/S.O.S. Flashlight
To Select a Channel
By scrolling through the Mode function, you will be able to
select or turn on preferred features of your microTALK® radio. When
scrolling through the Mode function, your radio features
will be displayed in the same predetermined order:
Both radios must be tuned to the
same channel to communicate.
Dense foliage and hilly terrain will further
reduce the range of the radio.
On FRS Channels 8 through 14, your radio
automatically switches to low power, which
will limit the range the radio can communicate.
Your microTALK® radio incorporates two advanced coded squelch
systems that can help to reduce interference from other users
on any given channel. CTCSS (Continuous Tone Coded Squelch
System) provides 38 privacy codes and DCS (Digitally Coded Squelch)
provides 83 privacy codes. This provides a total of 121 Privacy
Codes. Either system can be used on all channels, but both systems
cannot be used on the same channel at the same time.
Press the LED flashlight button below the TALK
button to use the LED flashlight located at the
bottom of the radio.
Both radios must be tuned to the same
channel/privacy code to communicate.
3. Press and hold the Talk button while
speaking into the microphone.
4. When finished talking, release the Talk
button and listen for a response.
Turning on Your microTALK® Radio
Press and hold the Mode/Power button until you hear
a series of audible tones indicating the radio is on.
Your microTALK® radio is now in Standby mode,
ready to receive transmissions. The radio is always in
Standby mode except when the Talk, Call or
Mode/Power buttons are pressed.
1
In VOX mode, your microTALK® radio can be used “hands-free,” automatically
transmitting when you speak. You can set the VOX sensitivity level to fit the
volume of your voice and avoid transmissions triggered by background noise.
To turn VOX mode on or off:
1. Press the Mode/Power button until the VOX
icon flashes on the display. The current On or Off
setting is displayed.
2. Press the Channel Up or Channel Down
button to turn VOX On or Off.
3. When VOX is turned on or off, press the
Mode/Power button to proceed to other functions,
or press Talk button to return to Standby mode.
3. When your desired CTCSS privacy code is displayed, press the
Mode/Power button to enter the new setting and proceed to other
functions, or press Talk button to return to Standby mode.
To set VOX sensitivity:
Set DCS Privacy Codes
1. Press the Mode/Power button until the VOX icon
flashes and the current sensitivity level is displayed.
The current VOX sensitivity level is
displayed with letters “L” and a Number 1
through 5, with Number 5 being the most
sensitive level and Number 1 being the
least sensitive level.
If CTCSS is turned on at the channel selected,
the display will flash the DCS icon and “OFF.”
To switch from CTCSS to DCS, press the
Channel Up or Channel Down button while
the display is flashing “OFF.” The display will
then show the small numbers flashing and
you will then be able to proceed to step 2.
2. Press the Channel Up or Channel Down
button to change the setting.
3. When VOX is turned on or off, press the
Mode/Power button to proceed to other functions,
or press Talk button to return to Standby mode.
2. Press using the Channel Up or Channel Down button to select a DCS
privacy code. You can hold the Up or Down button for fast advance.
The privacy code 00 is not a privacy code, but allows all
signals to be heard on a channel that is set to 00 on both
the CTCSS and DCS systems.
See page 18 for FRS/GMRS frequency
allocations and compatibility charts.
4
5
2
Voice Activated Transmit (VOX)
To select a DCS privacy code:
1. After selecting a channel, press the Mode/Power
button until the DCS icon appears and the small
numbers flash on the display (00 through 83).
To successfully communicate using a privacy code, both
the sending and receiving radios must be tuned to the same
channel and to the same privacy code system (CTCSS or DCS)
and privacy code number. Each channel will remember the
last privacy code system and number you select.
Your microTALK® radio will automatically shut off weak transmissions
and unwanted noise due to terrain, conditions or if you’ve reached
your Maximum Range limit.
3
Quick Start
1. Press and hold the Mode/Power button to turn on your radio.
2. Press the Channel Up or Channel Down button to select
a channel.
2. Press using the Channel Up or Channel Down button to select a
privacy code. You can hold the Up or Down button for fast advance.
Privacy Codes
Auto Squelch/Maximum Range
Channels 1 through 7 are shared with FRS/ GMRS.
Channels 8 through 14 are FRS only. Channels 15
through 22 are GMRS only.
If charging light is not on, check position of radio. Radio should be
upright. The charge indicator light will stay on until the charging is
complete.
If DCS is turned on at the channel
selected, the display will flash the
CTCSS icon and “OFF.” To switch from
DCS to CTCSS, press the Channel Up
or Channel Down button while the display
is flashing “OFF.” The display will then
show the small numbers flashing and you
will then be able to proceed to step 2.
Set CTCSS Privacy Codes
Set DCS Privacy Code
Set Vox On/Off
Set Vox Sensitivity
Set Call Tones 1-10
Set VibrAlert On/Off
Set Roger Beep On/Off
Set Key Tones On/Off
To activate S.O.S. function, press and hold the
LED flashlight button to turn on. Press and release to turn off the
flashlight or S.O.S. function.
With the radio on, select any of the 22 channels by
pressing the Channel Up or Channel Down button.
3. Plug the charging cable into a power source. For
pluggable equipment, the socket-outlet shall be
installed near the equipment and shall be easily
accessible.
1. After selecting a channel, press
the Mode/Power button until the CTCSS icon
appears and the small numbers next to the
channel number flash on the display.
Scrolling Through the Mode Function
LED/S.O.S. Flashlight
Both radios must be tuned to the
same channel to communicate.
2. Insert the micro-USB cable into jack on back of charger.
Note: Charger should be installed near the equipment
and easily accessible.
To select a CTCSS privacy code:
Mode Functions
Buildings and foliage in the path of the
signal can reduce the range of the radio.
See page 9 on how to select between
ten call tone settings.
1. Insert radio(s) into desktop charger as shown.
Set CTCSS Privacy Codes
Operation
In flat, open country your radio will
operate at maximum range.
The other person will hear a three second call
tone. This tone is used only to establish voice
communications.
For charging microTALK radio(s) in desktop charger:
This radio floats with included NiMH batteries.
It may not float with some other AA batteries.
microTALK® Range
Press and release the Call button.
1. Press and hold the Talk button.
2. With the microphone about two inches (5 cm) from
your mouth, speak in a normal voice.
3. Release the Talk button when you are
finished talking and listen for a response.
You cannot receive incoming calls while
pressing the Talk button.
Using Your Radio
• Use only the supplied rechargeable batteries and charger for recharging
your Cobra microTALK® radio.
• Cobra recommends your radio is turned off while being charged.
• It normally takes about 15 hours to fully charge batteries.
• Non-rechargeable alkaline batteries can also be used in your radio.
Important FCC Licensing Information
This radio operates on General Mobile Radio
Service (GMRS) frequencies which require a
Federal Communications Commission (FCC)
license. See page 22 for licensing and other
related information.
• Low Battery
Audible Alert
A double beep sound is used to confirm your lock on
or off request. When in Lock mode,
the Lock icon will be displayed.
Call Button
10
• Battery/Power Saver
To turn the lock on or off:
Press and hold the Call/Lock button for
3-4 seconds.
A double beep sound is used to indicate
the minimum and maximum volume levels
(1 through 8).
11
1. Battery Level Indicator
2. Roger Beep Icon
3. VOX Icon
4. Weather Icon
5. Lock Icon
6. Hi/Med/Low Power Icon
7. DCS/CTCSS Icons
8. Scan/Memory Icon
9. Weather Alert Icon
10. DCS/CTCSS Privacy Code Numbers
11. Power Saver Icon
12. Channel Numbers
13. Receive/Transmit Icon
14. Memory Channel Number
15. VibrAlert® / Call Alert Icon
16. Key Tone Icon
17. BURP Icon
18. Signal Strength Meter
• Button Lock
7
5 17
Operation
Installing Batteries
To install or replace batteries:
1. Remove belt clip by releasing belt clip latch and
Remove Belt Clip
sliding clip up.
2. Loosen the two top and bottom screws on the
back of the radio to remove the battery
compartment cover. HINT: the screws should be
loose enough (and sticking up) that you could use
Insert Batteries
them to help pull off the battery door if needed.
3. Insert the supplied three AA rechargeable
batteries or non-rechargeable alkaline batteries.
Position batteries according to polarity markings.
4. Replace battery compartment cover, screw down
the screws and re-attach the belt clip.
Tip of Belt Clip
5. Tighten the screws using the tip of the belt clip to
secure the battery door to the radio. Do not
overtighten. Only use the tip of the belt clip to
tighten the screws.
• Do not attempt to charge alkaline batteries.
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc), or
rechargeable (Ni-Cd, Ni-MH, etc.) batteries.
To charge batteries in radio:
Radio Charger Jack
1. Check to see that the batteries are inserted properly.
2. Insert the cable into the charge jack located at the
top of the radio.
3. Plug the charging cable into a power source.
14
16
• Call Alert
Five selectable
tones
Your range will vary depending on terrain and conditions.
Communicating with Another Person
Talk Button
Release the Talk button to receive incoming
transmissions. Your microTALK® radio is always
in Standby mode while the Talk or Call buttons
are not pressed.
12
• LED Flashlight
The Lock function locks the Channel Up, Channel
Down, Volume Up, Volume Down and Mode/Power
buttons to prevent accidental operation.
Press the Volume Up or Volume
Down button.
Auto Battery Save
8
9
7
• Backlit LCD Display
3
4 1
15
• Scan
Channels,
privacy codes
5
3
13
8
• Tri-Watch
Lock Function
To Adjust Volume
The radio’s LCD display will show a blinking
charging status indicator while charging.
18
2
6
• VibrAlert®
Silent Paging
21
For any questions about operating this new Cobra branded product,
PLEASE CONTACT US FIRST...do not return this product to the retail store.
The contact information for support will vary depending on the country in
which you purchased and utilize the product.
To obtain warranty service or other information for products purchased
and utilized in the U.S.A., please call our consumer support line at
(866) 721-3805, or email us at support@altistec.com. You will receive
instructions on how to ship the products at your expense to an Altis Global
Limited Authorized Service Center. To obtain service, you must include:
(a) a copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; and, most importantly;
(c) your address and telephone number.
For warranty and customer service information outside the US, please
contact your local dealer.
For further information needed on its features,
please visit www.cobrawalkietalkie.com
©2017 Altis Global Limited
for frequently asked questions and the
Berkeley Lake, GA US 30071
electronic manual.
www.cobrawalkietalkie.com
A-1
When battery power is low, the final bar in the
Battery Low icon will blink and an audible tone will
sound twice before the radio shuts off. Your batteries
should be replaced or recharged, if using
rechargeable batteries.
6
9
Product Service & Support
18
• Hands-Free Operation
(VOX)
13
10
Customer Assistance
®
• 121 Privacy Codes
(38 CTCSS codes/
83 DCS codes)
14
The belt clip easily attaches to your belt, purse, or
backpack.
Printed in China
Part No. KEM-ML38202-28
English
• Weather Alert
12
Carrying your microTALK radio with you is easy
when using the belt clip or optional wrist strap.
ACXT1035 SNOW
• 10 Channel
Weather Radio
17
®
TWO-WAY RADIO MODEL
• 22 Channels
Seven shared
with FRS/GMRS,
seven FRS only,
eight GMRS only.
Caring for Your microTALK® Radio
Your microTALK® radio will give you years of trouble-free service
if cared for properly. Handle the radio gently. Keep the radio away from dust.
Avoid exposure to extreme temperatures.
Mode Functions (continued on back side)
3. When DCS privacy code is displayed, press the Mode/Power button
to enter the new setting and proceed to other functions, or press the
Talk button to return to Standby mode.
6
7
8
Operation
Mode Functions (continued)
Ten Call Tone Settings
Roger Beep Confirmation Tone
Key Tone On/Off
10 Memory Location
Your listener will hear an audible tone when you release the Talk button.
This alerts the other party that you are finished talking and it is OK for
them to speak.
When Key Tone is On, an audible tone will sound each time a button is
pressed.
Your microTALK radio has 10 Memory Locations for storing your most
frequently used channels and channel/privacy code combinations.
These Memory Locations can be selected individually or can be scanned.
1. Press the Mode/Power button several times until
the ROGER BEEP icon flashes with the current on
or off setting displayed.
1. Press the Mode/Power button until the letter “C”
and the current call tone number (01 through 10)
is displayed. The current call tone will sound for
three seconds.
Call Tone Setting
To turn key tone on or off:
To turn roger beep on or off:
You can choose between ten different Call Tone Settings to transmit
a call alert.
To change a call tone setting:
2. Press the Channel Up or Channel Down button to
select roger beep on or off.
c. Do not press any buttons for 12 seconds to
return to Standby mode.
TW DCS Scan
a. Press the Mode button to enter the new setting
and proceed to other functions.
b. Press Talk or Call/Lock button to return to
Standby mode.
c. Do not press any buttons for 12 seconds to
BURP return
Power
Saver
to Standby
mode.
9
10
BURP
Privacy Code Scan
Weather (WX) Alert Mode
BURP features allows the user to expel water from inside the speaker
grille. This is useful if the radio is dropped in the water which may
become trapped in the speaker grille and muffle the audio.
R
Vox
X
To activate BURP:
HI MED LO1. WX
Press and release the MEM/ESC and H-M-L
at the same time.
TWbuttons
DCS Scan
CTCSS
Memtone(s) at maximum level will sound
2.
The Burp
from the internal speaker for 8 seconds. During
this time, BURP will appear in the display.
BURP Icon
Your microTALK® radio can automatically scan the Privacy Codes (either
CTCSS 01 through 38 or DCS 01 through 83) within one channel. Only
one set of privacy codes (CTCSS or DCS) can be scanned at a time.
Turning On the Weather Alert function will allow your radio to
automatically receive NOAA weather signals and warnings from
designated weather broadcast stations. If the radio is turned ON, it will
alert to Weather and other emergency alerts broadcast by NOAA.
To scan privacy codes:
1. While in Standby mode, press and release the
Scan button twice (CTCSS) or three times
(DCS) until the CTCSS or DCS icon and numbers
are flashing.
3. Hold the radio with the speaker grille down to help
BURP Powerthe
Saver
water drain out.
4. After an 8-second interval, the radio will return to
standby.
The Scan icon will continue to be displayed when
privacy code scan is on. Your radio will continue to
scan privacy codes and stop as an incoming
transmission is detected. Your radio will remain on
that channel/privacy code for 6 seconds.
Channel Scan
Your microTALK® radio can automatically scan channels.
To scan channels:
1. Press and release the Scan button until the Scan
icon and the channel numbers appear
on the display.
You can use your microTALK® radio to listen to NOAA All Hazards Radio
channels transmitting in your area.
The radio ignores specific privacy
codes while scanning channels.
4. Press the Weather button again to save the new
setting.
To listen to All Hazards Radio channels:
The Scan icon will continue to be displayed when
scan is on. Your radio will continue to scan all
channels and stop if an incoming transmission is
detected. Your radio will remain on that channel for
6 seconds.
5. To return to two way mode press the TALK button
on the side.
1. Press the Weather button until the All Hazards
Radio icon and the currently selected All Hazards
Radio channel are displayed.
Hazards Radio Icon
During scanning (while receiving an incoming transmission),
you can choose from the following:
a. Press and hold the Talk button to communicate on that channel.
Your radio will remain on that channel and return to Standby mode.
b. Press the Channel Up or Channel Down button to resume
scanning channels.
c. Press and hold the Scan button to return to Standby.
2. Use the Channel Up or Channel Down
button to change All Hazards Radio channels.
3. The All Hazards Radio icon will continue to
be displayed when All Hazards Radio is on.
4. To exit and return to two way mode press the
TALK button.
*National Oceanographic and Atmospheric Administration
15
16
17
A
B
C
D
E
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
1
2
3
4
5
6
7
FRS/GMRS
FRS/GMRS
FRS/GMRS
FRS/GMRS
FRS/GMRS
FRS/GMRS
FRS/GMRS
FRS
FRS
FRS
FRS
FRS
FRS
FRS
GMRS
GMRS
GMRS
GMRS
GMRS
GMRS
GMRS
GMRS
462.5625
462.5875
462.6125
462.6375
462.6625
462.6875
462.7125
467.5625
467.5875
467.6125
467.6375
467.6625
467.6875
467.7125
462.5500
462.5750
462.6000
462.6250
462.6500
462.6750
462.7000
462.7250
High
High
High
High
High
High
High
Low
Low
Low
Low
Low
Low
Low
High
High
High
High
High
High
High
High
11
8
12
9
13
10
14
15
14
Warranty & Trademark Acknowledgment
Limited One-Year Warranty
Licensed users will be issued a call sign by the FCC, which should be used for station identification when
operating this radio. GMRS users should also cooperate by engaging in permissible transmissions only, avoiding
channel interference with other GMRS users, and being prudent with the length of their transmission time.
Altis Global Limited warrants that this product and the component parts thereof, will be
free from defects in workmanship and materials for a period of one year from the date of
first consumer purchase. This warranty may be enforced by the first consumer
purchaser, and is not transferable. If the product is under warranty, it will be repaired or
exchanged depending on the model at Altis’ sole discretion. Such remedy may be your
sole and exclusive remedy for any breach of warranty.
The procedure for obtaining service and support, and the applicability of this warranty,
will vary depending on the country or jurisdiction in which you purchase and utilize the
product. For details on obtaining product service, support and warranty please visit
www.cobrawalkietalkie.com.
Provided that the product is utilized in the U.S.A., Altis will, without charge, repair or
replace, at its option, defective products, products or component parts upon delivery to
the authorized Altis Global Limited Authorized Service Center, accompanied by proof of
the date of first customer purchase, such as a duplicated copy of a sales receipt.
You must pay any initial shipping charges required to ship the product for warranty
service, but the return charges, to an address in the U.S.A., will be at Altis’ expense, if
the product is under warranty.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state and country to country.
Exclusions: This limited warranty does not apply: 1) To any product damaged by
accident; 2) In the event of misuse, ordinary wear, failure to follow directions, or
improper maintenance of the product or as a result of unauthorized alterations or repairs;
3) If the serial number has been altered, defaced, or removed; 4) If the product was
purchased or is utilized in a jurisdiction not covered by the limited warranty.
All implied warranties, including warranties of merchantability and fitness for a particular
purpose are limited in duration to the length of this warranty. Altis shall not be liable for
any inconsequential or other damages, including without limitation, damages resulting
from the loss of use or cost of installation.
Some states and countries do not allow limitations on how long an implied warranty lasts
and do not allow the exclusion or limitation of incidental or consequential damages, so
the above limitations may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from state to state and country to country.
For licensing information and application forms, please call the FCC Hotline at 800-418-FORM. Request form
#159 and form #605. Questions regarding the license application should be directed to the FCC at
888-CALL-FCC. Additional information is available on the FCC’s website at www.fcc.gov.
Channel 1 through 7 on low power and channels 8 through 14 comprise the FRS (Family Radio Service). No
license is required to operate on the FRS.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.”
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
A = Channel No. for 22 Channel FRS/GMRS Models
B = Channel No. for 15 Channel GMRS Models
C = Type of Radio Service
D = Frequency in MHz
E = Power Output
3. Press the Channel Up and Channel Down button
to turn Weather Alert On or Off.
NOAA* All Hazards Radio Channels
13
This two-way radio operates on GMRS (General Mobile Radio Service) frequencies which require an FCC (Federal
Communications Commission) license. A user must be licensed prior to operating on Channels 1 through 7 on
high power or 15 through 22, which comprise the GMRS channels of this radio. Serious penalties could result for
unlicensed use of GMRS channels, in violation of FCC rules. Operation of this radio is subject to additional rules
specified in 47 C.F.R. Part 95.
Important: Please note that Cobra GMRS models with 15 Channels
may designate different channel numbers for the same frequency.
For example, a Cobra 15 Channel GMRS model would need to be
tuned to Channel 11 in order to communicate with a 22 Channel
GMRS tuned to Channel 15. Please refer to the chart below for
channel/ frequency number compatibility.
1. Press the Weather button to enter the All Hazards
(Weather) radio mode.
After the Tri-Watch scan stops to monitor
a channel, as long as you do not press any
buttons within 6 seconds, your radio will
automatically resume scanning the
Tri-Watch channels
IMPORTANT NOTICE: FCC LICENSE REQUIRED
FRS/GMRS Frequency Allocation and Compatibility
2. Press the Weather button twice and the Weather
Alert icon flashes on the display. The current On or
Off setting is displayed.
2. Press and hold the Scan button to begin scanning
channels.
12
General Specifications
To turn Weather Alert On or Off:
3. Press and hold the MEM/ESC button to return to
Standby mode on the selected memory location.
4. Press Channel Up or Channel Down button to
resume scanning the Tri-Watch channels or to
change the scan direction.
5. To EXIT the Tri-Watch scan, press the TRI-WATCH
button again, and the radio will return to GMRS
Standby mode.
General Specifications & Licensing
Make sure the strongest Weather
channel is selected for your area
using the NOAA All Hazards Radio
Channels selection in the
previous menu.
Using Tri-Watch:
1. From GMRS Standby mode, press the TRI-WATCH
button. The TW will appear in the display along with
the three channels stored in the Tri-Watch memory.
2. The radio will scan through the three (3) Tri-Watch
memory channels.
3. A signal on any one (1) of the three (3) channels
will stop the scan for 6 seconds to allow you to
listen to the traffic on that location.
A memory location can be reprogrammed
at any time it is displayed. Press the
MEM/ESC button to begin.
Operation
This feature is set to OFF by default.
2. Press and hold the Scan button to begin scanning
privacy codes within the selected channel.
BURP Power Saver
11
2. Press the Channel Up or Channel Down button to
select a memory location (0 through 9).
If a location has been programmed before,
its associated channel/privacy code will
be shown on the display.
b. Press the MEM/ESC button to switch from
CTCSS to DCS. The DCS icon and privacy code
numbers will flash on the display. The Channel
Up or Channel Down button can then be used
to select a DCS privacy code (00 through 83)
for the channel.
Channel 8 through 14 only operates on
Low power setting.
3. Choose
one ofSaver
the following:
BURP
Power
CTCSS Mem
Memory
TW
DCSChannel
Scan
CTCSS Mem
a. Press the Channel Up or Channel Down
button to select a CTCSS privacy code (00
through 38) for the channel.
2. When the desired power is selected, press the
Talk button to return to Standby mode.
1. Press the MEM/ESC button until the Memory icon
and the memory location number flash on the
display.
Vox
HI MED LO WX
7. Press the MEM/ESC button. The CTCSS icon and
privacy code numbers will flash on the display.
8. Choose one of the following:
2. Press Channel Up or Channel Down button to
select the desired Tri-Watch channel.
3. Press and release TRI-WATCH button to confirm
entry.
4. Repeat steps 2 and 3 to program the remaining
additional Tri-Watch memory channel.
5. After programming both Tri-Watch memory
channels the radio will immediately engage
Tri-Watch mode.
To recall a stored memory channel location:
6. Press the Channel Up or Channel Down button
to select a channel (1 through 22).
1. Press the H-M-L button to select between
High, Medium and Low power settings.
The HI, MED or LO icons will show on the display
for the selected level.
Vox
2. Press the Channel Up or Channel Down button to
HI change
MED LO
WXsetting.
the call
Call Tone On/
Vibrate Off
5. Press the MEM/ESC button. The channel
numbers will flash on the display.
To toggle between H-M-L Power Modes:
Setting icon
on the display. The current
TWflashes
DCS Scan
setting (“01”
vibrate
+ ring, “02” ring only) is
CTCSS
Mem
displayed.
R
X
4. Press the Channel Up or Channel Down button
R
X
to select the memory location.
The main channel number will flash to
indicate channel position.
b. Press and hold the MEM/ESC button to save the current state of the
Set Memory Function and press the MEM/ESC button again return
to Standby mode.
3. Press the MEM/ESC button to enter a new
memory location or edit an already programmed
memory location.
Your radio can transmit selectively at 0.5, 1, or 2 watts of power. Use the
low power setting for short-range communications and use the high
power setting for long-range communications.
To changeVox
call settings:
HI
MEDthe
LOMode
WX button several times until the Call
1. Press
a. Press the MEM/ESC button to enter the channel/privacy code in the
selected memory location. Radio then proceeds to next memory
location, which will blink.
If a location has been programmed before,
its associated channel/privacy code will be
shown on the display.
Set High/Medium/Low (H-M-L) Power Button
Your MicroTALK® radio can alert you to incoming signals by sounding an
audible call tone or an audible tone with VibrAlert®.
Vibrate On
2. Press the Channel Up or Channel Down button
to select the memory location (0 through 9).
c. Do not press any buttons for 12 seconds to
return to Standby mode.
VibrAlert® and Call Alert
R
Call Tone On/X
2. Press the Channel Up or Channel Down button to
select key tone on or off.
Your microTALK® radio can be set up to scan three of your favorite
channels for activity.
To Program or Edit the Tri-Watch Channels:
1. Press and hold the TRI-WATCH button from GMRS
Standby mode for two (2) seconds to activate
Tri-Watch Setup mode. The TW icon on the
display will turn ON.
9. Choose one of the following:
1. Press the MEM/ESC button. Memory icon and
the Memory Location show on the display.
b. Press Talk or Call/Lock button to return to
Standby mode.
b. Press Talk or Call/Lock button to return to
Standby mode.
3. Choose one of the following:
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
b. Press Talk or Call/Lock button to return to
Standby mode.
c. Do not press any buttons for 12 seconds to
return to Standby mode.
To program a memory location:
3. Choose one of the following:
a. Press the Mode/Power button to enter the
Standby mode.
3. Choose one of the following:
a. Press the Mode/Power button to enter the new
setting and proceed to other functions.
2. Press the Channel Up or Channel Down button to
hear the other call tone settings.
1. Press the MODE button several times until the
KEY TONE (music note) icon flashes with the
current on/off setting.
Tri-Watch Set-up
If “oF” flashes in place of the privacy code numbers, a privacy
code is already set in the opposite (CTCSS or DCS) system.
Press the Channel Up or Channel Down button to cancel the
opposite code and select a privacy code from the active
system for the selected channel.
®
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Safety Information for microTALK Radios
Your wireless handheld portable transceiver contains a low power transmitter. When the talk button is pushed, it
sends out radio frequency (RF) signals. The device is authorized to operate at a duty factor not to exceed 50%. In
August 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety
levels for handheld wireless devices.
Important
FCC RF Exposure Requirements: For body-worn operation, this radio has been tested and meets the FCC RF
exposure guidelines when used with Cobra accessories supplied or designated for this product. Use of other
accessories may not ensure compliance with FCC RF exposure guidelines. Use only the supplied antenna.
Unauthorized antennas, modifications or attachments could damage the transmitter and may violate FCC
regulations.
For Products Purchased Outside the U.S.A.
Please contact your local dealer for warranty information.
Normal Position
Hold the transmitter approximately 2 inches from your face and speak in a normal voice, with the antenna
pointed up and away.
90-Day Warranty on Rechargeable Batteries
For products purchased in the U.S.A. and Canada.
MODEL ACXT1035 SNOW:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: 1) This device may not cause harmful interference, and 2) this device must accept
any interference received,including interference that may cause undesired operation.
Trademark Acknowledgment
Manufactured, distributed, or sold by Altis Global Limited, official licensee for this
product. Cobra®, microTalk®, Nothing Comes Close to a Cobra®, and the snake design
are registered trademarks of Cobra Electronics Corporation, USA. Cobra Electronics
Corporation™ is a trademark of Cobra Electronics Corporation, USA. All other product or
service names are the property of their respective owners.
©2017 Altis Global Limited, Berkeley Lake, GA, USA. All rights reserved.
FCC Warnings: Replacement or substitution of transistors, regular diodes or other parts of a
unique nature, with parts other than those recommended by Cobra may cause a violation of
the technical regulations of part 95 of the FCC rules, or violation of type acceptance
requirements of part 2 of the rules.
18
19
20