SC-PMX80_PC-TQBJ2004.book 1 ページ
2017年4月14日 金曜日 午前9時21分
Owner’s Manual
CD Stereo System
Model No. SC-PMX80
Thank you for purchasing this product.
Please read these instructions carefully before using this product, and save this
manual for future use.
If you have any questions, visit:
www.panasonic.ca/english/support
Table of contents
IMPORTANT SAFETY INSTRUCTIONS................................................2
Maintenance ..........................................................................................3
Supplied accessories ...........................................................................3
Preparing the remote control...............................................................3
Placement of speakers .........................................................................3
Making the connections .......................................................................4
Overview of controls ............................................................................4
About Bluetooth® ..................................................................................5
Bluetooth® operations ..........................................................................6
Media information .................................................................................7
Inserting media .....................................................................................7
Media playback controls ......................................................................8
FM radio .................................................................................................9
Clock and timers ...................................................................................9
Sound effects ......................................................................................10
Using the auxiliary input ....................................................................10
Using the PC input ..............................................................................10
Others .................................................................................................. 11
Troubleshooting .................................................................................. 11
Specifications......................................................................................13
Limited Warranty.................................................................................15
TQBJ2004-1
PC
2017/04/05
SC-PMX80_PC-TQBJ2004.book 2 ページ
2017年4月14日 金曜日 午前9時21分
Do the procedures with the remote control. You can
also use the buttons on the main unit if they are the
same.
Your system and the illustrations can look differently.
This Owner’s Manual is applicable to the following
system.
System
SC-PMX80
Main unit
SA-PMX80
Speakers
SB-PMX70
IMPORTANT
SAFETY
INSTRUCTIONS
Read these operating instructions carefully before using
the unit. Follow the safety instructions on the unit and the
applicable safety instructions listed below. Keep these
operating instructions handy for future reference.
TQBJ2004
1
2
3
4
5
6
7
2
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8 Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9 Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding-type plug has
two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10 Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11 Only use attachments/accessories specified by the
manufacturer.
12 Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the
apparatus. When a cart is used, use
caution when moving the cart/
apparatus combination to avoid injury
from tip-over.
13 Unplug this apparatus during lightning
storms or when unused for long periods of time.
14 Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
WARNING!
Unit
• To reduce the risk of fire, electric shock or product damage,
- Do not expose this unit to rain, moisture, dripping or
splashing.
- Do not place objects filled with liquids, such as vases, on
this unit.
- Use only the recommended accessories.
- Do not remove covers.
- Do not repair this unit by yourself. Refer servicing to
qualified service personnel.
CAUTION!
Unit
• To reduce the risk of fire, electric shock or product damage,
- Do not install or place this unit in a bookcase, built-in
cabinet or in another confined space. Ensure this unit is
well ventilated.
- Do not obstruct this unit’s ventilation openings with
newspapers, tablecloths, curtains, and similar items.
- Do not place sources of naked flames, such as lighted
candles, on this unit.
• This unit is intended for use in moderate climates.
• The power plug is the disconnecting device.
Install this unit so that the power plug can be unplugged
from the socket outlet immediately.
• This unit may receive radio interference caused by mobile
telephones during use. If such interference occurs, please
increase separation between this unit and the mobile
telephone.
• This unit utilizes a laser. Use of controls or adjustments or
performance of procedures other than those specified
herein may result in hazardous radiation exposure.
Battery
•
•
•
•
•
Do not break open or short-circuit the battery.
Do not charge the alkaline or manganese battery.
Do not use the battery if the cover has peeled off.
Do not heat or expose to flame.
Do not leave the battery(ies) in a car exposed to direct
sunlight for a long period of time with doors and windows
closed.
• Remove the battery if you do not use the remote control for
a long period of time. Keep in a cool, dark area.
• Danger of explosion if battery is incorrectly replaced.
Replace only with the type recommended by the
manufacturer.
• When disposing of the batteries, please contact your local
authorities or dealer and ask for the correct method of
disposal.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE SCREWS.
NO USER-SERVICEABLE PARTS
INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within
the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
2017年4月14日 金曜日 午前9時21分
This transmitter must not be co-located or operated
in conjunction with any other antenna or transmitter.
This equipment complies with IC radiation exposure
limits set forth for an uncontrolled environment and
meets the RSS-102 of the IC radio frequency (RF)
Exposure rules. This equipment has very low levels
of RF energy that is deemed to comply without
maximum permissive exposure evaluation (MPE).
But it is desirable that it should be installed and
operated keeping the radiator at least 20 cm (7 7/8q)
or more away from person’s body (excluding
extremities: hands, wrists, feet and ankles).
This device complies with Industry Canada’s
licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause undesired
operation of the device.
Contains IC: 216A-B21R1401
Supplied accessories
Placement of speakers
Check and identify the supplied accessories.
∏
1 x AC power supply ∏
cord
(K2CB2YY00065)
1 x Remote control
(N2QAYB001101)
∏
1 x FM indoor
antenna
(RSAX0002)
1 x Remote control
battery
∏
2 x Speaker cables
(REE1713)
∏
Place the speakers so that the tweeter is on the inner
side. To prevent damage to the speakers, do not touch
the speaker cones if you remove the nets.
• The enclosed Canadian French label sheet
corresponds to the English display on the front and
rear of the main unit.
• Product numbers provided in this Owner’s Manual are
correct as of January 2017. These may be subject to
change.
Preparing the remote control
CAN ICES-3(B)/NMB-3(B)
The device meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102 and
compliance with RSS-102 RF exposure, users can
obtain Canadian information on RF exposure and
compliance.
R6/LR6, AA
Maintenance
• To clean this system, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean
this system.
• Before using chemically treated cloth, read the
instructions that came with the cloth carefully.
Tweeter
• Use alkaline or manganese battery.
• Install the battery so that the poles (+ and –) align with
those in the remote control.
• Point the remote control at the remote control sensor,
away from obstacles, at a maximum range of
7 m (23 ft) directly in front of the main unit, within an
angle of approximately 30° to the left and right.
Use only the supplied speakers.
The combination of the main unit and speakers give the
best sound. You can cause damage to the system and
decrease the sound quality if you use other speakers.
Note:
• Keep your speakers more than 10 mm (13/32q) from the main
unit for ventilation.
• Put the speakers on a flat safe surface.
• These speakers do not have magnetic shielding. Do not
put them near TVs, PCs or other equipment easily
influenced by magnetism.
• When you play at high levels for a long period, it can cause
damage to the system and decrease the life of the system.
• Decrease the volume in these conditions to prevent
damage:
- When you play distorted sound.
- When you adjust the sound quality.
CAUTION!
• Use the speakers only with the recommended
system. If not, you can cause damage to the
amplifier and speakers and can cause a fire.
Consult an approved service personnel if damage
occurs or if there is a sudden apparent change in
performance.
• Do the procedures included in these instructions
when you attach the speakers.
TQBJ2004
SC-PMX80_PC-TQBJ2004.book 3 ページ
3
SC-PMX80_PC-TQBJ2004.book 4 ページ
2017年4月14日 金曜日 午前9時21分
Making the connections
Connect the AC power supply cord only after all the
other connections have been made.
2
1
Conserving power
The system consumes a small amount of power ( 13),
even when it is in standby mode. Disconnect the power
supply if you do not use the system.
Some settings will be lost after you disconnect the
system. You have to set them again.
Overview of controls
10
Connecting other equipment
2
You can connect a VCR, DVD player etc.
Main unit (rear)
11
e.g. DVD player
(not supplied)
3
4
To household AC outlet
1
Connect the antenna.
Place the antenna where reception is best.
Connect the speakers.
Main unit (rear)
i: Copper
j: Silver
12
EXT-IN
RADIO
Audio cable (not supplied)
6
Note:
2
CD/USB
5
Tape
(not supplied)
• If radio reception is poor, use an outdoor antenna
(not supplied).
9
1
• Disconnect the AC power supply cord before connection.
• Switch off all equipment and read the appropriate operating
instructions.
• Components and cables are sold separately.
• If you want to connect equipment other than those
described, refer to the audio dealer.
• Sound distortion can occur when you use an adaptor.
13
14
7
15
DIMMER
8
16
17
VOLUME
BASS
TREBLE
11
6
TQBJ2004
To right speaker
(rear)
4
Left speaker (rear)
Be careful not to cross (short-circuit) or reverse
the polarity of the speaker wires as doing so may
damage the speakers.
3
Connect the AC power supply cord.
Do not use an AC power supply cord with other
equipment.
SELECTOR
1
4
18
5V 2.1A
PAIRING
OPEN/CLOSE
19
5
20
21
22
23
2017年4月14日 金曜日 午前9時21分
1 Standby/on switch [Í], [Í/I]
Press to switch the unit from on to standby mode or
vice versa. In standby mode, the unit is still
consuming a small amount of power.
> [2]> [4]
3 Delete a programed track
4 Select audio source
On the remote control
[
]: “BLUETOOTH”
[CD/USB]: “CD” (. “USB”*1
[RADIO, EXT-IN]: “FM” ------. “AUX”
^--- “PC” (b
On the main unit
[SELECTOR]:
“CD” ----------. “BLUETOOTH” ------------. “FM”
^----- “PC” (--- “USB”*1 (--- “AUX” (-b
5 Basic playback control
6 Select the sound effects
7 Set the play menu item
8 View content information
9 Clock and timer operation
10 Set the program function
11 Adjust the volume of the system
12 Mute the sound of the system
Press the button again to cancel.
“MUTE” is also canceled when you adjust the volume
or when you switch off the system.
13 Enter setup menu
14 Set the radio menu item
15 Select the option
16 Dim the display panel
Press the button again to cancel.
About Bluetooth®
18 Port for iPhone/iPad/iPod and USB devices
19 Bluetooth®-pairing button
• Press to select “BLUETOOTH” as the audio source.
• Press and hold to enter pairing mode ( 6) or
disconnect a Bluetooth® device ( 6).
2 Numeric buttons [1 to 9, 0, S10]
• To select a 2-digit number
Example: 16: [S10] > [1] > [6]
• To select a 3-digit number
Example: 124: [S10] > [S10] >[1]
17 Display panel
20 Open or close the disc tray
21 Headphones jack ( )
• Plug type: 3.5 mm (1/8q) stereo (not supplied)
• Avoid listening for prolonged periods of time to prevent
hearing damage.
• Excessive sound pressure from earphones and
headphones can cause hearing loss.
• Listening at full volume for long periods may damage
the user’s ears.
22 Disc tray
• Do not put any object in front of the disc tray.
23 Remote control sensor
*1: The display will automatically change to “IPOD” when a
compatible iPhone/iPad/iPod is connected to the port for
iPhone/iPad/iPod.
Panasonic bears no responsibility for data and/or
information that is compromised during a
wireless transmission.
Frequency band used
• This system uses the 2.4 GHz frequency band.
Certification of this device
• This system conforms to frequency restrictions and
has received certification based on frequency laws.
Thus, a wireless permit is not necessary.
• The actions below are punishable by law in some
countries:
- Taking apart or modifying this system.
- Removing specification indications.
Restrictions of use
• Wireless transmission and/or usage with all Bluetooth®
equipped devices is not guaranteed.
• All devices must conform to standards set by Bluetooth
SIG, Inc.
• Depending on the specifications and settings of a
device, it can fail to connect or some operations can be
different.
• This system supports Bluetooth® security features. But
depending on the operating environment and/or
settings, this security is possibly not sufficient.
Transmit data wirelessly to this system with caution.
• This system cannot transmit data to a Bluetooth®
device.
Range of use
• Use this device at a maximum range of 10 m (33 ft).
The range can decrease depending on the
environment, obstacles or interference.
Interference from other devices
• This system may not function properly and troubles
such as noise and sound jumps may arise due to radio
wave interference if this system is located too close to
other Bluetooth® devices or the devices that use the
2.4 GHz band.
• This system may not function properly if radio waves
from a nearby broadcasting station, etc. is too strong.
Intended usage
• This system is for normal, general use only.
• Do not use this system near an equipment or in an
environment that is sensitive to radio frequency
interference (example: airports, hospitals, laboratories,
etc).
TQBJ2004
SC-PMX80_PC-TQBJ2004.book 5 ページ
5
SC-PMX80_PC-TQBJ2004.book 6 ページ
2017年4月14日 金曜日 午前9時21分
Bluetooth® operations
Connecting a paired Bluetooth® device
By using the Bluetooth® connection, you can listen to the
sound from the Bluetooth® audio device from this system
wirelessly.
• Refer to the operating instructions of the Bluetooth®
device for details.
1
Press [
] to select “BLUETOOTH”.
“READY” is indicated on the display.
2
Select “SC-PMX80” from the Bluetooth® device’s
Bluetooth® menu.
The name of the connected device is indicated on
the display for a few seconds.
Connecting via Bluetooth® menu
Preparation
• Turn on the Bluetooth® feature of the device and place
the device near this unit.
Pairing with Bluetooth devices
®
1
Press [
] to select “BLUETOOTH”.
If “PAIRING” is indicated on the display, go to step 3.
2
Press [PLAY MENU] to select “PAIRING” and
then press [OK].
Alternatively, press and hold [
-PAIRING] on the
unit.
3
4
3
Start playback on the Bluetooth® device.
• If prompted for the passkey, input “0000”.
• You can register up to 8 devices with this unit. If a 9th
device is paired, the device that has not been used for the
longest will be replaced.
• This unit can only be connected to one device at a time.
• When “BLUETOOTH” is selected as the source, this unit
will automatically try and connect to the last connected
Bluetooth® device. (“LINKING” is indicated on the display
during this process.) If the connection attempt fails, try to
establish a connection again.
Bluetooth® transmission mode
Select “SC-PMX80” from the Bluetooth® device’s
Bluetooth® menu.
The MAC address (e.g., 6C:5A:B5:B3:1D:0F) may
be displayed before “SC-PMX80” is displayed.
The name of the connected device is indicated on
the display for a few seconds.
You can change the transmission mode to prioritize
transmission quality or sound quality.
Preparation
• Press [
] to select “BLUETOOTH”.
• If a Bluetooth® device is already connected, disconnect
it.
Start playback on the Bluetooth® device.
1
Press [PLAY MENU] repeatedly to select
“LINK MODE”.
Press [2, 1] to select the mode and then press
[OK].
MODE 1: Emphasis on connectivity
MODE 2: Emphasis on sound quality
Note:
TQBJ2004
1
Press [PLAY MENU] repeatedly to select “INPUT
LEVEL”.
2
Press [2, 1] to select the level and then press [OK].
“LEVEL 0” ,. “LEVEL i1” ,. “LEVEL i2”
Note:
2
6
Bluetooth® input level
If the sound input level from the Bluetooth® device is too
low, change the input level setting.
Preparation
• Connect a Bluetooth® device.
• Select “MODE 1” if the sound is interrupted.
• When enjoying video contents with this function, the video
and audio output may not be synchronised. In this case,
select “MODE 1”.
• The factory default is “MODE 2”.
Note:
^----------------------------------------------J
• Select “LEVEL 0” if the sound is distorted.
• The factory default is “LEVEL 0”.
Disconnecting a Bluetooth® device
1
While a Bluetooth® device is connected:
Press [PLAY MENU] repeatedly to select
“DISCONNECT?”.
2
Press [2, 1] to select “OK? YES” and then press
[OK].
Note:
• You can also disconnect the Bluetooth® device by pressing
and holding [
-PAIRING] on the unit.
• The Bluetooth® device will be disconnected if a different
audio source (e.g., “CD”) is selected.
Bluetooth® standby
When “SC-PMX80” is selected from a paired Bluetooth®
device’s Bluetooth® menu, this unit will turn on
automatically from standby mode and establish a
Bluetooth® connection.
1
Press [SETUP] repeatedly to select
“BLUETOOTH STANDBY”.
2
Press [2, 1] to select “ON” and then press [OK].
Note:
• To turn the function off, select “OFF” in step 2.
• The factory default is “OFF”. If this function is set to “ON”,
the standby power consumption will increase.
2017年4月14日 金曜日 午前9時21分
Media information
Compatible CD
• Please be aware that Panasonic accepts no
responsibility for the loss of data and/or information.
Compatible iPhone/iPad/iPod
iPhone 7 Plus / iPhone 7 / iPhone SE /
iPhone 6s Plus / iPhone 6s / iPhone 6 Plus / iPhone 6 /
iPhone 5s / iPhone 5c / iPhone 5 / iPhone 4s
iPad Pro (9.7-inch and 12.9-inch) / iPad Air 2 /
iPad Air / iPad (3rd and 4th generation) / iPad 2 /
iPad mini 4 / iPad mini 3 / iPad mini 2 (iPad mini
with Retina display) / iPad mini
iPod touch (5th and 6th generation)
iPhone/iPad/iPod or USB device
• This system can play back discs that conform to the
CD-DA format.
• This system can play back CD-R/RW with CD-DA or
MP3 format content.
• The unit may not be able to play some discs due to the
condition of the recording.
• Before playback, finalize the disc on the device it was
recorded on.
• If the disc includes both MP3 and normal audio data
(CD-DA), the unit plays the type recorded in the inner
part of the disc.
• This unit cannot play files recorded using packet write.
• Disc must conform to ISO9660 level 1 or 2 (except for
extended formats).
Note:
iPod nano (7th generation)
(as of January 2017)
• For the latest information, visit
http://panasonic.jp/support/global/cs/audio/
(This site is in English only.)
Note:
• Do not connect models not listed in the above. Unexpected
behaviour may occur.
• Compatibility depends on the software version. Update
your iPhone/iPad/iPod to the latest software before using it
with this unit.
• Read the User Guide of the iPhone/iPad/iPod for the
operating instructions.
• Some CD-R/RW cannot be played because of the
condition of the recording.
• MP3 files are defined as tracks and folders are defined as
albums.
• This system can access up to:
- CD-DA: 99 tracks
- MP3: 999 tracks, 255 albums (including root folder)
• Recordings will not necessarily be played in the order you
recorded them.
Inserting media
• Files are defined as tracks and folders are defined as
albums.
• This system can access up to:
- 800 albums (including root folder)
- 8000 tracks
- 999 tracks in one album
Press [CD/USB] repeatedly to select “USB”.
The display will automatically change to “IPOD” when a
compatible iPhone/iPad/iPod is connected to the port.
Charging an iPhone/iPad/iPod
During unit on, charging starts when an iPhone/iPad/
iPod is connected to this unit.
• After the iPhone/iPad/iPod has started charging, you
can turn the unit to standby mode.
• Check the iPhone/iPad/iPod to see if the battery is fully
charged. (Once fully charged, remove the iPhone/iPad/
iPod.)
• Remove the CD only after it stops rotating.
• When connecting an iPhone/iPad/iPod, use the dedicated
USB cable (not supplied).
• Insert the USB device directly. Do not use any USB
extension cable.
• Please disconnect the USB device if you finish using.
• Before removing the USB device, select a source other
than “USB”.
Label facing up
OPEN/CLOSE
5V 2.1A
Note:
CD
Compatible USB devices
• This unit does not guarantee connection with all USB
devices.
• FAT12, FAT16 and FAT32 file systems are supported.
• This unit supports USB 2.0 High Speed.
• USB devices with storage capacity of more than 32 GB
cannot work in some conditions.
• Supported file formats and extensions:
MP3 (“.mp3”), AIFF (“.aiff”), FLAC (“.flac”), WAV
(“.wav”), AAC (“.m4a”), DSD (“.dff”, “.dsf”)
• Depending on how you create the files, they may not
play in the order you numbered them or may not play
at all.
Note:
• Connect only compatible iPhone/
iPad/iPod models ( left).
Failure to do so may result in
unexpected behaviour.
OPEN/CLOSE
Press [CD/USB] repeatedly to select “CD”.
TQBJ2004
SC-PMX80_PC-TQBJ2004.book 7 ページ
7
SC-PMX80_PC-TQBJ2004.book 8 ページ
2017年4月14日 金曜日 午前9時21分
Media playback controls
The following marks indicate the availability of the
feature.
[CD]:
CD audio in CD-DA format or a CD that
contains MP3 files
[iPod]:
Compatible iPhone/iPad/iPod connected to
the USB port.
[USB]:
USB devices containing MP3/AIFF/FLAC/
WAV/AAC/DSD files
[Bluetooth]: Connected Bluetooth® device
Preparation
• Turn the unit on.
• Insert the media or connect the Bluetooth® device.
• Press [CD/USB] or [
] to select the audio source.
Basic controls [CD] [iPod] [USB] [Bluetooth]
Play
Press [1/;].
Stop
Press [∫].
• [USB]: The position is memorized and
“RESUME” is displayed.
• [USB]: Press [∫] twice to stop the
playback fully.
Pause
Press [1/;].
Press again to continue playback.
Skip
Press [:] or [9] to skip track.
(main unit: [:/6] or [5/9])
[CD] [USB]: Press [3] or [4] to skip the
MP3/AIFF/FLAC/WAV/AAC/DSD
album.
Search
During play or pause
Press and hold [6] or [5].
(main unit: [:/6] or [5/9])
Viewing available information [CD] [USB]
[Bluetooth]
You can display the track, artist, album name, file type,
bit rate, and other information. (The information varies
depending on the audio source.)
Press [DISPLAY] repeatedly.
e.g. [USB] (MP3)
“A”: Album number
“T”: Track number
(“  ” stands for a number.)
“
”: Album
“
”: Track
Note:
• Maximum characters that can be shown:
approximately 32
• This system supports ver. 1 and 2 ID3 tags.
• Text data that the system does not support can show
differently.
Play menu [CD] [USB]
1
Press [PLAY MENU] to select “PLAYMODE” or
“REPEAT”.
2
Press [2, 1] to select the setting and then press
[OK].
PLAYMODE
TQBJ2004
Turns on repeat mode.
• “`” is displayed.
OFF REPEAT
Turns off repeat mode.
Note:
• During random playback, you cannot skip to tracks which
have been played or press the numeric buttons.
• Playmode function does not work with “Program playback”.
• The mode is canceled when you open the disc tray or
remove the USB device.
Program playback [CD] [USB]
This function allows you to program up to 24 tracks.
[CD] (CD-DA)
1
Press [PROGRAM] in the stop mode.
“PROGRAM” is shown for a few seconds.
2
Press the numeric buttons to select the desired
track.
Do this step again to program other tracks.
3
Press [1/;] to start playback.
[CD] (MP3), [USB]
1
Press [PROGRAM] in the stop mode.
“PROGRAM” is shown for a few seconds.
2
3
Press [3, 4] to select the desired album.
Cancels the play mode setting.
1-TRACK
Only plays the selected track.
• “1”, “ ” is displayed.
(Skip to the desired track.)
4
Press [OK].
Do steps 2 through 4 again to program other tracks.
1-ALBUM
Only plays the selected MP3/AIFF/
FLAC/WAV/AAC/DSD album.
• Press [3] or [4] to select the MP3/
AIFF/FLAC/WAV/AAC/DSD album.
• “1”, “ ” is displayed.
5
Press [1/;] to start playback.
Note:
8
ON REPEAT
OFF
PLAYMODE
• [iPod]: Backwards search is only within
the current track.
• There will be no sound in search operation when playing
DSD files at USB selector.
• To use this unit’s remote control with a Bluetooth® device,
the Bluetooth® device must support AVRCP (Audio Video
Remote Control Profile).
Depending on the status of the device, some controls may
not work.
• Operation results may vary depending on the iPhone/iPad/
iPod models.
• [CD] [USB]: Tracks can be selected by pressing the numeric
buttons.
REPEAT
RANDOM
Plays the contents randomly.
• “RND” is displayed.
1-ALBUM
RANDOM
Plays the tracks in the selected MP3/
AIFF/FLAC/WAV/AAC/DSD album
randomly.
• Press [3] or [4] to select the MP3/
AIFF/FLAC/WAV/AAC/DSD album.
• “1”, “ ”, “RND” is displayed.
Press [9] and then press the numeric buttons
to select the desired track.
Check program Press [:] or [9] in the stop
contents
mode.
Clear the last
track
Press [DEL] in the stop mode.
Cancel
program mode
Press [PROGRAM] in the stop mode.
• “PGM OFF” is shown for a few seconds.
Clear all
programed
tracks
Press [∫] in the stop mode. “CLEAR
ALL” is shown. Within 5 seconds,
press [∫] again.
Note:
• The program memory is cleared when you open the disc
tray or remove the USB device.
2017年4月14日 金曜日 午前9時21分
FM radio
30 FM stations can be preset.
Preparation
Press [RADIO, EXT-IN] repeatedly to select “FM”.
Automatic presetting
1
2
3
Press [RADIO MENU] to select “A.PRESET”.
Press [2, 1] to select “LOWEST” or
“CURRENT” frequency.
LOWEST:
To begin auto preset with the lowest frequency
(FM 87.9 or FM 87.5).
CURRENT:
To begin auto preset with the current frequency*1.
Press [OK] to start presetting.
• The tuner starts to preset all the stations it can receive
into the channels in ascending order.
To cancel, press [∫].
*1: To change the frequency, refer to “Manual tuning and
presetting”.
Manual tuning and presetting
1
Press [6] or [5] to tune in to the station.
• Alternatively, press [:/6] or [5/9] on the
main unit when “MANUAL” is selected as the tune
mode*2.
2
3
To display the current FM signal status
Press [DISPLAY].
“FM ST”:
“FM - - - -”:
FM stereo broadcast is being received.
No broadcast is received or FM broadcast
received is weak or in monaural.
“FM MONO”: You have set the “FM MODE” to “MONO”.
( 11, “If noise is excessive during FM
reception.”)
Note:
• “STEREO” is displayed when this unit tunes to a stereo
broadcast.
Clock and timers
Setting the clock
This is a 12-hour clock.
1
2
Press [CLOCK/TIMER] to select “CLOCK”.
Press [3, 4] to set the time and then press [OK].
To check the time
Press [CLOCK/TIMER].
Note:
• Reset the clock regularly to maintain accuracy.
Sleep timer
To tune automatically, press and hold the button until
the frequency starts changing quickly.
The sleep timer switches off the system after the set
time.
Press [PROGRAM].
Press [SLEEP] repeatedly to select the setting (in
minutes).
Press the numeric buttons to select a preset
number.
Do steps 1 through 3 again to preset more stations.
The new station replaces any station that occupies
the same preset number.
Selecting a preset station
Press the numeric buttons, [:] or [9] to select
the preset station.
• Alternatively, press [:/6] or [5/9] on the main
unit when “PRESET” is selected as the tune mode*2.
*2: To change the tune mode
1 Press [RADIO MENU] repeatedly to select “TUNE
MODE”.
2 Press [2, 1] to select “MANUAL” or “PRESET”, and
then press [OK].
“SLEEP 30” -. “SLEEP 60” -. “SLEEP 90” -. “SLEEP 120”
^------------------- “OFF” (Cancel) (------------------b
Note:
• The remaining time is indicated on the unit’s display at
every minute except when other operations are performed.
“SLEEP 1” is always shown when only 1 minute remains.
• The sleep timer can be used together with the play timer.
• The sleep timer always comes first. Be sure not to set an
overlap of timers.
Play timer
You can set the timer to come on at a certain time to
wake you up.
Preparation
Set the clock.
1
Press [CLOCK/TIMER] repeatedly to select
“TIMER ADJ”.
2
Press [3, 4] to set the starting time (“ON TIME”)
and then press [OK].
3
Press [3, 4] to set the finishing time
(“OFF TIME”) and then press [OK].
4
Press [3, 4] to select the music source*3 and
then press [OK].
Turning the timer on
1
Prepare the selected music source and set the
desired volume.
2
Press [F, PLAY].
“F” is shown.
To cancel, press [F, PLAY] again.
The system must be switched off for the timer to
operate.
To check the settings
Press [CLOCK/TIMER] repeatedly to select “TIMER
ADJ”.
(During standby, press [CLOCK/TIMER] twice.)
Note:
• The timer starts at a low volume and increases gradually to
the preset level.
• The timer comes on at the set time every day if the timer is
on.
• If you switch off the system and switch on again while a
timer is in operation, the timer will not stop at the end time.
*3: “CD”, “USB”, and “FM” can be set as the music source.
• For timer music source through the port for iPhone/
iPad/iPod and USB devices, select “USB”.
TQBJ2004
SC-PMX80_PC-TQBJ2004.book 9 ページ
9
SC-PMX80_PC-TQBJ2004.book
10 ページ
2017年4月14日 金曜日 午前9時21分
Sound effects
Changing the sound quality
1
2
Press [SOUND] repeatedly to select a sound
effect.
Press [2, 1] to select the desired setting.
BASS
-4 to +4
TREBLE
SURROUND
Using the PC input
D.BASS
This function lets you enjoy a powerful bass effect.
Press [D.BASS] to select “ON D.BASS” or “OFF
D.BASS”.
Using the auxiliary input
You can connect a VCR, DVD player etc. and listen to
the audio through this system.
TQBJ2004
Preparation
Connect the external equipment.
10
1
Press [RADIO, EXT-IN] repeatedly to select
“AUX”.
2
Play the external equipment.
Connect the main unit and a PC.
1
Download and install the dedicated driver to the
PC. (Only for Windows OS)
Download and install the driver from the website
below.
Type B
Download and install the dedicated app
“Panasonic Audio Player 2” (free of charge) on
your PC. (For Windows OS and OS X)
Download and install the app from the website
below.
http://panasonic.jp/support/global/cs/audio/
(This site is in English only.)
(as of January 2017)
Type A
USB 2.0 cable
(not supplied)
http://panasonic.jp/support/global/cs/audio/
(This site is in English only.)
2
PC
USB
– Windows 7, Windows 8, Windows 8.1, Windows 10
– OS X 10.7, 10.8, 10.9, 10.10, 10.11, 10.12
Press [PRESET EQ] repeatedly to select a setting.
Adds punch to rock
For background music
Clarifies higher frequencies
Adds gloss to vocal
Cancels the sound effect
Disconnect the AC power supply cord.
Follow the steps below.
• Refer to the following for the recommended OS
versions for your PC:
Preset EQ
HEAVY
SOFT
CLEAR
VOCAL
FLAT
1
2
Main unit (rear)
USB-DAC port
Before connecting to a PC
“ON SURROUND” or
“OFF SURROUND”
By main unit only
Turn [BASS] or [TREBLE] to adjust the level.
Listening to audio from a PC
You can play back music on the PC with this system’s
speakers by connecting a PC to the PC IN terminal on
the main unit.
About supported format, refer to “Specifications” ( 13).
3
Connect the AC power supply cord to the main
unit and turn this system on.
4
5
Press [RADIO, EXT-IN] repeatedly to select “PC”.
Operate the PC for playback.
Note:
• When you play back high-resolution audio, it is
recommended that you use a compatible USB 2.0 High
Speed Cable.
11 ページ
2017年4月14日 金曜日 午前9時21分
Others
Auto off function
As a factory default, this unit will turn to standby mode
automatically if there is no sound and it is not being used
for approximately 20 minutes.
To cancel this function
1
2
Press [SETUP] repeatedly to select “AUTO OFF”.
Press [2, 1] to select “OFF” and then press
[OK].
Note:
• To turn the function on, select “ON” in step 2.
• This setting cannot be selected when radio is the source.
• When connected to a Bluetooth® device, the function does
not work.
Software update
Occasionally, Panasonic may release updated software
for this unit that may add or improve the way a feature
operates. These updates are available free of charge.
For more details, refer to the following website.
http://panasonic.jp/support/global/cs/
(This site is in English only.)
Checking the software version
Press [SETUP] repeatedly to select “SW VER.” and
then press [OK].
The version of the installed software is displayed.
• Press [OK] to exit.
Troubleshooting
Before requesting service, make the following checks. If
you are in doubt about some of the check points, or if the
solutions indicated do not solve the problem, consult
your dealer for instructions.
Common problems
Cannot turn on the unit.
• After connecting the AC power supply cord, wait about
10 seconds before turning on the unit.
No operations can be done with the remote control.
• Examine that the battery is installed correctly.
Sound is distorted or no sound.
• Adjust the volume of the system.
• Switch off the system, determine and correct the
cause, then switch the system on again. It can be
caused by straining of the speakers through excessive
volume or power, and when using the system in a hot
environment.
• Ensure the speaker cables are connected correctly
and securely. ( 4)
A “humming” sound can be heard during playback.
• An AC power supply cord or fluorescent light is near
the cables. Keep other appliances and cords away
from the cables of this system.
The unit does not work.
• One of the unit’s safety devices may have been activated.
1 Press [Í/I] on the unit to switch the unit to standby.
• If the unit does not turn off, disconnect the AC power
supply cord from the AC outlet, reconnect it to the outlet
after about 30 seconds. Then wait for about 10 seconds.
2 Press [Í/I] on the unit to switch it on. If the unit still
cannot be operated, consult the dealer.
Noise is heard.
• During “AUX” mode, when a device is connected to
both the AUX IN terminals and the USB port, noise
may be generated depending on the device. In this
case, remove the USB cable from the USB port.
Disc
Display not shown correctly.
Playback does not start.
• You have not put in the disc correctly. Put it in correctly.
• Disc is dirty. Clean the disc.
• Replace the disc if it is scratched, warped, or
non-standard.
• There is condensation. Let the system dry for 1 to 2 hours.
Radio
Reception is poor or a beat sound is heard.
• Keep the antenna away from computers, TVs, other
cables and cords.
• Use an outdoor antenna.
• Switch off the TV or move it away from the system.
If noise is excessive during FM reception.
• Change the audio to be output as monaural.
1 Press [RADIO MENU] repeatedly to select “FM MODE”.
2 Press [2, 1] to select “MONO” and then press [OK].
The sound becomes monaural.
• To cancel, select “STEREO” or change the frequency.
In normal circumstances, select “STEREO”.
Stations cannot be selected.
• Change the FM frequency step.
1 Press [SELECTOR] on the unit repeatedly to select “FM”.
2 Press and hold [∫] on the unit.
• After a few seconds the display changes to show the
current lowest frequency. Continue to hold the button
down. The lowest frequency changes and the step is
changed.
iPhone/iPad/iPod
Cannot charge or operate.
• Check that the iPhone/iPad/iPod is connected properly.
• Connect the iPhone/iPad/iPod again or try to restart
the iPhone/iPad/iPod.
• During standby mode, charging will not start from the
USB cable connection.
Turn this unit on and make sure the charging has
started before turning this unit to standby mode.
• The battery of the iPhone/iPad/iPod is depleted.
Charge the iPhone/iPad/iPod, and then operate again.
– When using the port, turn this unit on. Do not turn this
unit off until the iPhone/iPad/iPod becomes operational.
USB
The USB device or the contents in it cannot be read.
• The format of the USB device or the contents in it is/
are not compatible with the system.
Slow operation of the USB device.
• Large content size or large memory USB device takes
longer time to read.
The elapsed time shown is different from the actual
play time.
• Transfer the data to another USB device or backup the
data and reformat the USB device.
Bluetooth®
Pairing cannot be done.
• Check the Bluetooth® device condition.
The device cannot be connected.
• The pairing of the device was unsuccessful or the
registration has been replaced. Try pairing the device
again.
• This system might be connected to a different device.
Disconnect the other device and try pairing the device
again.
• If “MODE 2” is selected in “LINK MODE”, select
“MODE 1”. ( 6)
• If the problem persists, turn the unit off and on, then try
again.
TQBJ2004
SC-PMX80_PC-TQBJ2004.book
11
SC-PMX80_PC-TQBJ2004.book
12 ページ
2017年4月14日 金曜日 午前9時21分
The device is connected but audio cannot be heard
through this system.
• For some built-in Bluetooth® devices, you have to set
the audio output to “SC-PMX80” manually. Read the
operating instructions for the device for details.
The sound is interrupted.
• The device is out of the 10 m (33 ft) communication
range. Bring the Bluetooth® device closer to this
system.
• Remove any obstacle between this system and the
device.
• Other devices that use the 2.4 GHz frequency band
(wireless router, microwaves, cordless phones, etc.)
are interfering. Bring the Bluetooth® device closer to
this system and distance it from the other devices.
• Select “MODE 1” for stable communication. ( 6)
PC
The PC does not recognize this system.
• Check your operating environment. ( 10)
• Restart the PC, turn off and on this system, and then
reconnect the USB cable.
• Use another USB port of the connected PC.
• Install the dedicated driver if using a PC with Windows.
TQBJ2004
Main unit displays
12
“--:--”
• You connected the AC power supply cord for the first
time or there was a power failure recently. Set the
clock.
“ADJUST CLOCK”
• Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
• Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
• The unit has been left unused for about 20 minutes and will
shut down in a minute. Press any button to cancel it.
“CHECKING CONNECTION”
• The unit is checking the connected iPhone/iPad/iPod
or USB device.
• If this display keeps appearing, make sure that the
battery of the iPhone/iPad/iPod is not depleted and
that the iPhone/iPad/iPod is turned on and connected
correctly.
“DIMMER”
• Appears 10 seconds after the volume is turned to “0”.
“ERROR”
• An incorrect operation was done. Read the instructions
and try again.
“F” / “F” (“  ” stands for a number.)
• There is a problem with this unit.
Disconnect the AC power supply cord from the AC
outlet, reconnect it to the outlet after about 30 seconds.
Wait for about 10 seconds, then turn on the unit. If the
problem still persists, disconnect the AC power supply
cord and consult your dealer.
“NO DEVICE”
• The iPhone/iPad/iPod or USB device is not connected.
Examine the connection.
• The battery of the iPhone/iPad/iPod is depleted.
Charge the iPhone/iPad/iPod and turn it on before
connecting.
“NO DISC”
• You have not put in a disc or put in a disc that the
system cannot play.
“NO PLAY”
• Examine the content. You can only play supported
format. ( 13)
• The files in the USB device can be corrupted. Format
the USB device and try again.
• The unit may have a problem. Turn the unit off and
then on again.
“DEVICE NO RESPONSE”
“HUB NOT SUPPORTED”
“NOT SUPPORTED”
• You have connected an iPhone/iPad/iPod that cannot
be played.
• If the iPhone/iPad/iPod is compatible, turn it on and
connect it correctly.
• You have connected an unsupported USB device.
“PC UNLOCKED”
• “PC” is selected, but a PC is not connected.
“PGM FULL”
• The number of programed tracks is more than 24.
“PLAYERROR”
• You played an unsupported file. The system will skip
that track and play the next one.
“READING”
• The unit is checking the CD information. After this
display has disappeared, start operating.
• When starting playback of DSD files, it may take time
to read the file. Wait until reading completes.
“REMOTE ” (“ ” stands for a number.)
• The remote control and this unit are using different
codes. Change the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK]
and [1] for at least 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK]
and [2] for at least 4 seconds.
“USB OVER CURRENT ERROR”
• The iPhone/iPad/iPod or USB device is drawing too
much power. Remove the iPhone/iPad/iPod or USB
device. Switch the system off and on again.
“VBR”
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
“WAIT”
• This is displayed, for example, when this unit is turning off.
Memory reset (initialization)
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1
Disconnect the AC power supply cord.
Wait 30 seconds before you continue with step 2.
2
While you press and hold [Í/I] on the main unit,
connect the AC power supply cord again.
Keep holding down [Í/I] until “---------” appears on
the display.
3
Release [Í/I].
All the settings are set back to the factory default.
It is necessary to set the memory items again.
Remote control code
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
To set the code to “REMOTE 2”
1
2
3
Press [SELECTOR] on the main unit to select “CD”.
Press and hold [∫] on the main unit and [2] on
the remote control until “REMOTE 2” is shown.
Press and hold [OK] and [2] for a minimum of
4 seconds.
• The factory default is “REMOTE 1”.
• To change the mode back to “REMOTE 1”, repeat the
steps above but replace the button pressed on the
remote control from [2] to [1].
13 ページ
2017年4月14日 金曜日 午前9時21分
Specifications
General
Power supply
AC 120 V, 60 Hz
Power consumption
44 W
Dimensions (main unit)
(W x H x D) 211 mm x 114 mm x 267 mm
(8 5/16qk4 1/2qk10 1/2q)
Mass (main unit)
Approx. 2.8 kg (6.2 lbs)
Operating temperature range
0 °C to +40 °C (r32 oF to r104 oF)
Operating humidity range
35% to 80% RH (no condensation)
Power consumption in standby mode*1, 2
0.25 W (approx.)
(When “BLUETOOTH STANDBY” is “ON”)*2
0.35 W (approx.)
Amplifier section
RMS output power
Front Ch (both ch driven)
60 W per channel (3 ™), 1 kHz, 10% THD
Total RMS power
120 W
FM section
Preset memory
30 stations
Frequency range
87.9 MHz to 107.9 MHz (200 kHz step)
87.5 MHz to 108.0 MHz (100 kHz step)
Antenna terminals
75 ™ (unbalanced)
Disc section
Disc played (8 cm (3q) or 12 cm (5q))
CD, CD-R/RW (CD-DA, MP3*3)
Pick up
Wavelength
790 nm (CD)
Terminals section
USB Port
Terminal type: USB-A
USB port power
DC OUT 5 V 2.1 A
USB standard
USB 2.0 High Speed
Media file format support
MP3*3 (¢.mp3), AIFF (¢.aiff), FLAC (¢.flac),
WAV (¢.wav), AAC (¢.m4a), DSD (¢.dff/¢.dsf)
Audio Support format
MP3*3/AAC*4
Sampling frequency
32/44.1/48 kHz
Audio word size
16 bits
Channel count
2 ch
5/WAV
AIFF/FLAC*
Sampling frequency
32/44.1/48/88.2/96/176.4/192 kHz
Audio word size
16 bits/24 bits
Channel count
2 ch
DSD
2.8 MHz
USB device file system
FAT12, FAT16, FAT32
Terminal type: USB-B
PC IN (EXT-IN)*6
USB standard
USB 2.0 High Speed
USB Audio Class specification
USB Audio Class 2.0, Asynchronous mode
Audio support format
LPCM
Sampling frequency
32/44.1/48/88.2/96/176.4/192 kHz
Audio word size
16 bits/24 bits
Channel count
2 ch
DSD
2.8 MHz
1/8q) jack
Headphones
Stereo, 3.5 mm (
Analog audio input
AUX IN (EXT-IN)
Pin jack
Speaker section
Speaker unit(s)
Woofer
14 cm (5 1/2q) cone type x 1
Tweeter
1.9 cm (3/4q) dome type x 1
Super tweeter 1.5 cm (19/32q) piezoelectric type x 1
Impedance
3™
Dimensions (W x H x D) 161 mm x 238 mm x 262 mm
(6 5/16qk9 3/8qk10 5/16q)
Mass
Approx. 2.6 kg (5.7 lbs)
Bluetooth® section
Version
Class
Supported Profiles
Frequency band
Operation Distance
Supported Codec
Bluetooth® Ver.2.1+EDR
Class 2
A2DP, AVRCP
2.4 GHz band FH-SS
10 m (33 ft) Line of sight
AAC, SBC
Note:
• Specifications are subject to change without notice. Mass
and dimensions are approximate.
• Total harmonic distortion is measured by the digital
spectrum analyzer.
*1: “BLUETOOTH STANDBY” is “OFF”.
*2: No device is connected to the USB port before turning to
standby mode.
*3: MPEG-1 Layer 3, MPEG-2 Layer 3
*4: Support profile AAC-LC only.
*5: Uncompressed FLAC files may not operate correctly.
Support block size from 1152 to 4096.
*6: USB-DAC port
FLAC Decoder
Copyright (C) 2000,2001,2002,2003,2004,2005,2006,2007,
2008,2009 Josh Coalson
Redistribution and use in source and binary forms, with or
without modification, are permitted provided that the following
conditions are met:
- Redistributions of source code must retain the above copyright
notice, this list of conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright
notice, this list of conditions and the following disclaimer in the
documentation and/or other materials provided with the distribution.
- Neither the name of the Xiph.org Foundation nor the names of its
contributors may be used to endorse or promote products derived
from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS
AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED
WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL
THE FOUNDATION OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO,
PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS
OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
(INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY
OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGE.
TQBJ2004
SC-PMX80_PC-TQBJ2004.book
13
SC-PMX80_PC-TQBJ2004.book
14 ページ
2017年4月14日 金曜日 午前9時21分
MPEG Layer-3 audio coding technology licensed from Fraunhofer
IIS and Thomson.
The Bluetooth® word mark and logos are registered trademarks
owned by Bluetooth SIG, Inc. and any use of such marks by
Panasonic Corporation is under license.
Other trademarks and trade names are those of their respective
owners.
OS X is a trademark of Apple Inc., registered in the U.S. and other
countries.
Windows is a trademark or a registered trademark of Microsoft
Corporation in the United States and other countries.
The model number and serial number of this product
can be found on either the back or the bottom of the
unit.
Please note them in the space provided below and
keep for future reference.
MODEL
SC-PMX80
NUMBER
SERIAL
NUMBER
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
TQBJ2004
“Made for iPod”, “Made for iPhone”, and “Made for iPad” mean
that an electronic accessory has been designed to connect
specifically to iPod, iPhone, or iPad, respectively, and has been
certified by the developer to meet Apple performance standards.
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
Please note that the use of this accessory with iPod, iPhone, or
iPad may affect wireless performance.
iPad, iPhone, iPod, iPod nano, iPod touch, iPad Air, and Retina are
trademarks of Apple Inc., registered in the U.S. and other countries.
iPad mini and iPad Pro are trademarks of Apple Inc.
14
The symbols on this product (including the
accessories) represent the following:
AC
DC
Class II equipment (The construction of the
product is double-insulated.)
I
On
Í
Standby
SC-PMX80_PC-TQBJ2004.book
15 ページ
2017年4月14日 金曜日 午前9時21分
Limited Warranty
Panasonic Canada Inc.
5770 Ambler Drive, Mississauga, Ontario L4W 2T3
PANASONIC PRODUCT - LIMITED WARRANTY
Panasonic Canada Inc. warrants this product to be free from defects in material and workmanship under normal use and for a period as stated below from the date of original
purchase agrees to, at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your
purchase price. The decision to repair, replace or refund will be made by Panasonic Canada Inc.
Panasonic BD/DVD Product - One (1) year, parts and labour
Panasonic Audio Receivers - One (1) year, parts and labour
Home Theater Systems Product - One (1) year, parts and labour
This warranty is given only to the original purchaser, or the person for whom it was purchased as a gift, of a Panasonic brand product mentioned above sold by an authorized
Panasonic dealer in Canada and purchased and used in Canada, which product was not sold “as is”, and which product was delivered to you in new condition in the original
packaging.
IN ORDER TO BE ELIGIBLE TO RECEIVE WARRANTY SERVICE HEREUNDER, A PURCHASE RECEIPT OR OTHER PROOF OF DATE OF ORIGINAL PURCHASE,
SHOWING AMOUNT PAID AND PLACE OF PURCHASE IS REQUIRED
LIMITATIONS AND EXCLUSIONS
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO
DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by Panasonic Canada Inc., or failures which result from
accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance,
power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the
product, or service by anyone other than an Authorized Servicer, or damage that is attributable to acts of God.
Dry cell batteries are also excluded from coverage under this warranty.
THIS EXPRESS, LIMITED WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT WILL PANASONIC CANADA INC. BE LIABLE FOR ANY SPECIAL, INDIRECT OR
CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT OF ANY BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. (As
examples, this warranty excludes damages for lost time, travel to and from the Authorized Servicer, loss of or damage to media or images, data or other memory or recorded
content. This list of items is not exhaustive, but for illustration only.)
In certain instances, some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or the exclusion of implied warranties, so the above
limitations and exclusions may not be applicable. This warranty gives you specific legal rights and you may have other rights which vary depending on your province or territory.
For product operation, repairs and information assistance, please visit our Support page:
www.panasonic.ca/english/support
IF YOU SHIP THE PRODUCT TO A SERVICENTRE
Carefully pack and send prepaid, adequately insured and preferably in the original carton.
Include details of the defect claimed, and proof of date of original purchase.
TQBJ2004
WARRANTY SERVICE
15
SC-PMX80_PC-TQBJ2004.book
16 ページ
Panasonic Canada Inc.
5770 Ambler Drive,
Mississauga, Ontario,
L4W 2T3
www.panasonic.com
C Panasonic Corporation 2017
Printed in Malaysia
2017年4月14日 金曜日 午前9時21分
p
TQBJ2004-1
F0117YM2047
Download PDF