Copyright © 2016 YEALINK(XIAMEN) NETWORK TECHNOLOGY CO., LTD
Copyright © 2016 Yealink(Xiamen) Network Technology CO., LTD. All rights reserved. No parts of
this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, photocopying, recording, or otherwise, for any purpose, without the express written
permission of Yealink(Xiamen) Network Technology CO., LTD. Under the law, reproducing
includes translating into another language or format.
When this publication is made available on media, Yealink(Xiamen) Network Technology CO.,
LTD. gives its consent to downloading and printing copies of the content provided in this file only
for private use but not for redistribution. No parts of this publication may be subject to alteration,
modification or commercial use. Yealink(Xiamen) Network Technology CO., LTD. will not be
liable for any damages arising from use of an illegally modified or altered publication.
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS GUIDE ARE
SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND
RECOMMENDATIONS IN THIS GUIDE ARE BELIEVED TO BE ACCURATE AND PRESENTED
WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL
RESPONSIBILITY FOR THEIR APPLICATION OF PRODUCTS.
YEALINK(XIAMEN) NETWORK TECHNOLOGY CO., LTD. MAKES NO WARRANTY OF ANY KIND
WITH REGARD TO THIS GUIDE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Yealink(Xiamen) Network
Technology CO., LTD. shall not be liable for errors contained herein nor for incidental or
consequential damages in connection with the furnishing, performance, or use of this guide.
Hereby, Yealink(Xiamen) Network Technology CO., LTD. declares that this phone is in
conformity with the essential requirements and other relevant provisions of the CE, FCC.
You can find the CE and FCC information from the label on the back of the IP phone.
Statements of compliance can be obtained by contacting support@yealink.com.
This device is marked with the CE mark in compliance with EC Directives 2014/35/EU and 2014/30/EU.
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired
operation.
Note: This device is tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
1.
Reorient or relocate the receiving antenna.
2.
Increase the separation between the equipment and receiver.
3.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4.
Consult the dealer or an experience radio/TV technician for help.
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
We are striving to improve our documentation quality and we appreciate your feedback. Email
your opinions and comments to DocsFeedback@yealink.com.
Yealink SIP-T19(P) E2 IP phone firmware contains third-party software under the GNU General Public License
(GPL). Yealink uses software under the specific terms of the GPL. Please refer to the GPL for the exact terms
and conditions of the license.
The original GPL license, source code of components licensed under GPL and used in Yealink products can
be downloaded online:
http://www.yealink.com/GPLOpenSource.aspx?BaseInfoCateId=293&NewsCateId=293&CateId=293.
About This Guide
Thank you for choosing the SIP-T19 E2/SIP-T19P E2 (hereinafter referred to as SIP-T19(P) E2)
IP phone, exquisitely designed to provide business telephony features, such as Call
Hold, Call Transfer, Multicast Paging and Conference over an IP network. The difference
between the SIP-T19 E2 and SIP-T19P E2 IP phones is that only SIP-T19P E2 supports PoE.
This guide provides everything you need to quickly use your new phone. First, verify
with your system administrator that the IP network is ready for phone configuration. Also
be sure to read the Packaging Contents and Regulatory Notices sections in this guide
before you set up and use the SIP-T19(P) E2 IP phone.
Note
Network Directory and Network Call Log features are hidden for IP phones in neutral
firmware, which are designed for the BroadWorks environment. Please contact your
system administrator for more information.
Topics provided in this guide include:

Chapter 1
Overview

Chapter 2
Getting Started

Chapter 3
Customizing Your Phone

Chapter 4
Basic Call Features

Chapter 5
Advanced Phone Features
This section describes the changes to this guide for each release and guide version.
The following section is new:

Call Park on page 86
Major updates have occurred to the following sections:

Volume on page 28

Ring Tones on page 29
v
User Guide for the SIP-T19(P) E2 IP Phone

Programable Keys on page 52
The following section is new:

Entering Data and Editing Fields on page 18
Major updates have occurred to the following sections:
vi

Icon Instructions on page 3

Optional Accessories on page 10

Phone Installation on page 11

Troubleshooting on page 125

Appendix A - Time Zones on page 139
Table of Contents
About This Guide ...................................................................... v
In This Guide ......................................................................................................................... v
Summary of Changes .......................................................................................................... v
Changes for Release 80, Guide Version 80.130 ............................................................ v
Changes for Release 80, Guide Version 80.95 ............................................................. vi
Table of Contents ..................................................................... vii
Overview .................................................................................. 1
Hardware Component Instructions .................................................................................... 1
Icon Instructions .................................................................................................................... 3
LED Instructions ..................................................................................................................... 4
User Interfaces ..................................................................................................................... 4
Phone User Interface ........................................................................................................ 5
Web User Interface ........................................................................................................... 5
Documentations ................................................................................................................... 7
Getting Started ......................................................................... 9
Packaging Contents ............................................................................................................. 9
Optional Accessories ..................................................................................................... 10
Phone Installation ............................................................................................................... 11
Phone Initialization ............................................................................................................. 14
Phone Status ....................................................................................................................... 14
Basic Network Settings ...................................................................................................... 15
Registration ......................................................................................................................... 17
Idle Screen .......................................................................................................................... 18
Entering Data and Editing Fields ..................................................................................... 18
Customizing Your Phone ......................................................... 21
General Settings ................................................................................................................ 21
Contrast ............................................................................................................................ 21
Language......................................................................................................................... 22
Time & Date ..................................................................................................................... 23
Administrator Password ................................................................................................. 25
Key as Send ..................................................................................................................... 25
Phone Lock ....................................................................................................................... 26
vii
User Guide for the SIP-T19(P) E2 IP Phone
Audio Settings .................................................................................................................... 28
Volume ............................................................................................................................. 28
Ring Tones ........................................................................................................................ 29
Contact Management ....................................................................................................... 31
Directory........................................................................................................................... 31
Local Directory ................................................................................................................ 33
Blacklist ............................................................................................................................ 43
Remote Phone Book ........................................................................................................ 44
Call History Management ................................................................................................ 47
System Customizations ...................................................................................................... 49
Logo Customization ........................................................................................................ 49
Headset Use .................................................................................................................... 50
Programable Keys .......................................................................................................... 52
Account Registration ....................................................................................................... 57
Dial Plan ........................................................................................................................... 58
Emergency Number........................................................................................................ 63
Live Dialpad .................................................................................................................... 64
Hotline .............................................................................................................................. 65
Basic Call Features ................................................................. 67
Placing Calls ....................................................................................................................... 67
Answering Calls ................................................................................................................. 69
Ending Calls ........................................................................................................................ 70
Redialing Numbers ............................................................................................................ 70
Recent Call In Dialing ........................................................................................................ 71
Auto Answer ....................................................................................................................... 72
Auto Redial.......................................................................................................................... 73
Call Completion ................................................................................................................. 74
ReCall .................................................................................................................................. 75
Call Mute ............................................................................................................................. 76
Call Hold/Resume ............................................................................................................... 76
Do Not Disturb (DND) ........................................................................................................ 77
Call Forward ....................................................................................................................... 79
Call Transfer ........................................................................................................................ 82
Call Waiting ........................................................................................................................ 83
Conference ......................................................................................................................... 84
Local Conference ............................................................................................................ 84
Network Conference ...................................................................................................... 85
Call Park .............................................................................................................................. 86
FAC Mode ........................................................................................................................ 87
Transfer Mode ................................................................................................................. 89
Call Pickup .......................................................................................................................... 91
Anonymous Call ................................................................................................................. 94
Anonymous Call Rejection ................................................................................................ 95
viii
Table of Contents
Advanced Phone Features ..................................................... 97
Hot Desking ........................................................................................................................ 97
Intercom .............................................................................................................................. 99
Multicast Paging ............................................................................................................... 100
Sending RTP Stream ..................................................................................................... 100
Receiving RTP Stream ................................................................................................... 102
Using Multicast Paging ................................................................................................. 103
Music on Hold ................................................................................................................... 104
Shared Call Appearance (SCA) .................................................................................... 105
Configuring SCA Feature on the IP Phone ................................................................. 106
Using SCA Feature on the IP Phone ............................................................................ 109
Bridged Line Appearance (BLA) .................................................................................... 112
Configuring BLA Feature on the IP Phone .................................................................. 113
Using BLA Feature on the IP Phone ............................................................................. 116
Messages .......................................................................................................................... 117
Short Message Service (SMS) .................................................................................... 117
Voice Mail ...................................................................................................................... 119
Message Waiting Indicator (MWI) ............................................................................. 121
Troubleshooting .....................................................................125
General Issues .................................................................................................................. 125
Display Issues ................................................................................................................... 125
Password Issues ................................................................................................................ 126
Call Issues ......................................................................................................................... 127
Headset & Handset Issues .............................................................................................. 127
Audio Issues ...................................................................................................................... 128
Log Issues .......................................................................................................................... 130
Reboot & Upgrade & Reset Issues .................................................................................. 133
Regulatory Notices ................................................................137
Service Agreements ........................................................................................................ 137
Limitations of Liability ...................................................................................................... 137
Safety Instructions ............................................................................................................ 137
Appendix A - Time Zones ......................................................139
Index ......................................................................................141
ix
User Guide for the SIP-T19(P) E2 IP Phone
x
Overview
This chapter provides the overview of the SIP-T19(P) E2 IP phone. Topics include:

Hardware Component Instructions

Icon Instructions

LED Instructions

User Interfaces

Documentations
If you require additional information or assistance with your new phone, contact your
system administrator.
The main hardware components of the SIP-T19(P) E2 IP phone are the LCD screen and
the keypad.
1
User Guide for the SIP-T19(P) E2 IP Phone
Hardware component instructions of the SIP-T19(P) E2 IP phone are:
Item
Description
Shows information about calls, messages, soft keys,
time, date and other relevant data:
• Call information—caller ID, call duration
①
LCD Screen
• Icons (for example,
)
• Missed call text or second incoming caller information
• Prompt text (for example, "Saving config file!")
• Time and date
Indicates phone power status and phone status:
②
Power Indicator LED
• Receives an incoming call—Fast flashing
• Receives a voice mail or text message—Slow flashing
③
Soft Key
Label automatically to identify their context-sensitive
features.
Scroll through the displayed information.
④
Confirms actions or answers incoming calls.
⑤
(Message Key)
Accesses voice mails.
⑥
(Headset Key)
Toggles the headset mode.
⑦
(Mute Key)
Mutes or un-mutes an active call.
⑧
(Transfer Key)
Transfers a call to another party.
⑨
Speakerphone Key
Toggles the hands-free speakerphone mode.
⑩
RD Key
Redials a previously dialed number.
⑪
Volume Key
⑫
Keypad
⑬
Speaker
Adjusts the volume of the handset, headset, speaker,
and ringer.
Provides the digits, letters and special characters in
context-sensitive applications.
Provides hands-free (speakerphone) audio output.
Secures the handset in the handset cradle when the IP
⑭
Hookswitch Tab
phone is mounted vertically. For more information on
how to adjust the hookswitch tab, refer to Yealink Wall
Mount Quick Installation Guide for Yealink IP Phones.
Picking up the handset from the handset cradle, the
⑮
Hookswitch
hookswitch bounces and the phone connects to the line,
laying the handset down on the handset cradle, the
phone disconnects from the line.
2
Overview
Icons appearing on the LCD screen are described in the following table:
Icon
Description
Network is unavailable
The private line registers successfully
Register failed
Registering
The shared/bridged line registers
successfully
Hands-free speakerphone mode
Handset mode
Headset mode
Voice Mail
Text Message
Auto Answer
Do Not Disturb
Call Hold
Ringer volume is 0
Phone Lock
Call Mute
Received Calls
3
User Guide for the SIP-T19(P) E2 IP Phone
Icon
Description
Placed Calls
Missed Calls
Call Forward/Forwarded Calls
The contact icon
Power Indicator LED
LED Status
Description
Solid yellow
The phone is initializing.
Fast flashing yellow (300ms)
The phone is ringing.
Slow flashing yellow (1s)
The phone receives a voice mail or text message.
The phone is powered off.
The phone is idle.
Off
The phone is busy.
The call is placed on hold or is held.
The call is muted.
Note
The above introduces the default LED status. The statuses of the power indicator LED are
configurable via web user interface. For more information, refer to
Yealink_SIP-T2_Series_T19(P) E2_T4_Series_CP860_IP_Phones_Administrator_Guide.
Two ways to customize configurations of your SIP-T19(P) E2 IP phone:

The user interface on the IP phone.

The user interface in a web browser on your PC.
The hardware components keypad and LCD screen constitute the phone user interface,
which allows the user to execute all call operation tasks and basic configuration
changes directly on the phone. In addition, you can use the web user interface to
access all configuration settings. In many cases, either the phone user interface and/or
the web user interface interchangeably. However, in some cases, it is only possible to
4
Overview
use one or the other interface to operate the phone and change settings.
You can customize your phone by pressing the Menu soft key to access the phone user
interface. The Advanced Settings option is only accessible to the administrator, and the
default administrator password is ―admin‖ (case-sensitive). For more information on
customizing your phone with the available options from the phone user interface, refer
to Customizing Your Phone on page 21.
In addition to the phone user interface, you can also customize your phone via web user
interface. In order to access the web user interface, you need to know the IP address of
your new phone. To obtain the IP address, press the
key on the phone. Enter the IP
address (e.g., http://192.168.0.10 or 192.168.0.10) in the address bar of web browser on
your PC. The default administrator user name and password are both ―admin‖
(case-sensitive).
The options you can use to customize the IP phone via phone user interface and/or via
web user interface are listed in the following table:
Options
Phone User Interface
Web User Interface
√
√
Status
--IPv4
--MAC
--Firmware
--Network
--Phone
--Accounts
Basic Phone Settings
--Contrast
√
--Language
√
--Time & Date
√
--Administrator Password
√
--Key as Send
√
--Phone Lock
√
--Ring Tones
√
√
--Contact Management
--Directory
x
--Local Directory
√
--Blacklist
√
5
User Guide for the SIP-T19(P) E2 IP Phone
Options
--Remote Phone Book
Phone User Interface
Web User Interface
x
--Call History Management
√
--Logo Customization
x
--Programable Keys
x
--Account Registration
√
--Dial Plan
x
--Emergency Number
x
--Live Dialpad
x
--Hotline
√
Basic Call Features
--Recent Call In Dialing
x
--Auto Answer
√
--Auto Redial
√
--Call Completion
√
--ReCall
x
--Do Not Disturb (DND)
√
--Call Forward
√
--Call Transfer
√
--Call Waiting
√
--Conference
x
--Call Pickup
√
--Anonymous Call
√
--Anonymous Call Rejection
√
√
Advanced Phone Features
--Hot Desking
√
--Intercom
√
--Multicast Paging
x
--Shared Call Appearance (SCA)
x
--Bridged Line Appearance (BLA)
x
--Music on Hold
x
--Messages
√
√
SIP Account
--User Options
--Active Line
√
--Label
√
--Display Name
√
--Register Name
√
--User Name
√
--Password
√
--Server Option
6
√
Overview
Options
Note
Phone User Interface
--SIP Server 1/2
√
--Register Port
x
--Outbound Status
√
--Outbound Proxy1/2
√
--Proxy Fallback Interval
√
--NAT Status
√
Web User Interface
The table above lists most of the feature options. Please refer to the relevant sections for
more information.
The following table shows documentations available for the SIP-T19(P) E2 IP phone.
Name
Contents
Basic call features
Quick Start Guide
Where found
Language
In the package
English
On the website
English/Chinese
On the website
English/Chinese
and phone
customizations
Phone/Web user
interface settings
User Guide
Basic call features
and advanced
phone features
7
User Guide for the SIP-T19(P) E2 IP Phone
8
Getting Started
This chapter provides basic installation instructions and information for obtaining the
best performance with the SIP-T19(P) E2 IP phone. Topics include:

Packaging Contents

Phone Installation

Phone Initialization

Phone Status

Basic Network Settings

Registration

Idle Screen

Entering Data and Editing Fields
If you require additional information or assistance with your new phone, contact your
system administrator.
The following components are included in your SIP-T19(P) E2 IP phone package:

SIP-T19(P) E2 IP Phone
9
User Guide for the SIP-T19(P) E2 IP Phone

Phone Stand

Handset & Handset Cord

Ethernet Cable

Quick Start Guide
Check the list before installation. If you find anything missing, contact your system
administrator.
The following items are optional accessories for your SIP-T19(P) E2 IP phone. You need to
purchase them separately if required.
10
Getting Started
Note

Power Adapter

Headset
We recommend that you use the accessories provided or approved by Yealink. The use
of unapproved third-party accessories may result in reduced performance.
If your phone is already installed, proceed to Phone Initialization on page 14.
This section introduces how to install the phone:
1)
Attach the stand
2)
Connect the handset and optional headset
3)
Connect the network and power
11
User Guide for the SIP-T19(P) E2 IP Phone
1)
Note
Attach the stand
The hookswitch tab has a lip which allows the handset to stay on-hook when the IP phone
is mounted vertically.
2)
Connect the handset and optional headset
3)
Connect the network and power
You have two options for power and network connections. Your system administrator will
advise you which one to use.
Note
12

AC power

Power over Ethernet (PoE)
PoE is not applicable to the SIP-T19 E2 IP phone.
Getting Started
AC Power
To connect the AC power:
1.
Connect the DC plug on the power adapter to the DC5V port on the phone and
connect the other end of the power adapter into an electrical power outlet.
2.
Connect the included or a standard Ethernet cable between the Internet port on
the phone and the one on the wall or switch/hub device port.
Note
The IP phone should be used with Yealink original power adapter (5V/600mA) only. The
use of the third-party power adapter may cause the damage to the phone.
Power over Ethernet
With the included or a regular Ethernet cable, the SIP-T19P E2 IP phone can be powered
from a PoE-compliant switch or hub.
To connect the PoE for the SIP-T19P E2 IP phone:
1.
Connect the Ethernet cable between the Internet port on the phone and an
available port on the in-line power switch/hub.
Note
If in-line power is provided, you don’t need to connect the phone to the power adapter.
Make sure the switch/hub is PoE-compliant.
The phone can also share the network with another network device such as a PC
(personal computer). This is an optional connection.
Important! Do not remove power from the phone while it is updating firmware and
configurations.
13
User Guide for the SIP-T19(P) E2 IP Phone
After your phone is powered on, the system boots up and performs the following steps:
Automatic Phone Initialization
The phone finishes the initialization by loading the saved configuration. The LCD screen
displays ―Welcome Initializing…please wait‖ during this process.
DHCP (Dynamic Host Configuration Protocol)
The phone attempts to contact a DHCP server in your network to obtain valid IPv4
network settings (e.g., IP address, subnet mask, default gateway address and DNS
address) by default.
Note
If your network does not use DHCP, proceed to Basic Network Settings on page 15.
You can view phone status via phone user interface or web user interface.
Available information of phone status includes:

Network status (e.g., IPv4 status, IP mode and MAC address).

Phone status (e.g., product name, hardware version, firmware version, product ID,
MAC address and device certificate status).

Note
Account status (e.g., register status of SIP accounts).
You can view device certificate status via phone user interface only.
To view the phone status via phone user interface:
1.
Press
, or press Menu->Status.
2.
Press
or
to scroll through the list and view the specific information.
To view the phone status via web user interface:
14
1.
Open a web browser of your computer.
2.
Enter the IP address in the browser’s address bar, and then press the Enter key.
Getting Started
3.
Enter the user name (admin) and password (admin) in the login page.
4.
Click Confirm to login.
The phone status is displayed on the first page of the web user interface.
If your phone cannot contact a DHCP server for any reason, you need to configure
network settings manually. The IP phone can support either or both IPv4 and IPv6
addresses.
To configure the IP mode via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin)
->Network->WAN Port.
15
User Guide for the SIP-T19(P) E2 IP Phone
2.
Press
or
to select IPv4, IPv6 or IPv4 & IPv6 from the IP Mode field.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
You can configure a static IPv4 address for the IP phone. Before configuring it, make sure
that the IP mode is configured as IPv4 or IPv4 & IPv6.
To configure a static IPv4 address via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin)
->Network->WAN Port.
2.
Press
to select the IPv4 and then press the Enter soft key.
3.
Press
to select Static IPv4 Client and then press the Enter soft key.
4.
Enter the desired value in the IPv4, Subnet Mask, Default Gateway, IPv4 Pri.DNS
and IPv4 Sec.DNS field respectively.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
You can configure a static IPv6 address for the IP phone. Before configuring it, make sure
that the IP mode is configured as IPv6 or IPv4 & IPv6.
To configure a static IPv6 address via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin)
->Network->WAN Port.
16
2.
Press
to select IPv6 and then press the Enter soft key.
3.
Press
to select Static IPv6 Client and then press the Enter soft key.
Getting Started
4.
Enter the desired value in the IPv6 IP, IPv6 IP Prefix, IPv6 Default Gateway, IPv6
Pri.DNS and IPv6 Sec.DNS field respectively.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
If you are using an xDSL modem, you can connect your phone to the Internet via PPPoE
mode. Set the WAN port as a PPPoE port. The PPPoE port will perform a PPP negotiation
to obtain the IP address. Contact your system administrator for the PPPoE user name
and password.
To configure PPPoE via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin)
->Network->WAN Port.
Note
2.
Press
to select IPv4 and then press the Enter soft key.
3.
Press
to select PPPoE IPv4 Client and then press the Enter soft key.
4.
Enter the user name and password in the corresponding fields.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
The wrong network settings may result in inaccessibility of your phone and may also
have an impact on your network performance. For more information on these
parameters, contact your system administrator.
Generally, your phone will be deployed with multiple other phones. In this case, your
system administrator will configure the phone parameters beforehand, so that after you
start up your phone, the phone will be registered and ready for use. The SIP-T19(P) E2 IP
phone supports only one account. If your phone is not registered, you may have to
register it. For more information on how to register your phone, refer to Account
Registration on page 57.
17
User Guide for the SIP-T19(P) E2 IP Phone
If the phone has successfully started up, the idle LCD screen will be displayed as below.
The idle screen displays the label of current account, time and date, and four soft keys.
You can enter data and edit fields using the phone keypad.
Keypad on the phone provides different characters (or numbers) when using the 2aB,
abc, Abc, ABC or 123 input mode. You can change the following input modes to enter
data and edit fields on your phone. When your phone keypad matches the input mode,
you can press the keypad repeatedly to view the character (or numbers) options and
stop to select. When the character (or numbers) you want to enter displays in the field,
wait one second, and enter the next character (or numbers).
The following table lists the input modes and character (or numbers) options for the
keypad:
Input Mode
Keypad
Abc
2aB
abc
(initials in
ABC
123
capitals)
1
abc2äæ å
abc2äæ å
ABC2Ä Æ Å
àáâãç
àáâãç
ÀÁÂÃÇ
def3èéêë
def3èéêë
DEF3ÈÉÊË
ð
ð
Ð
4ghiGHI
ghi4ìíîï
ghi4ìíîï
GHI4ÌÍÎÏ
4
5jklJKL
jkl5£
jkl5£
JKL5£
5
6mnoMN
mno6öøò
mno6öøò
MNO6Ö Ø
O
óôõñ
óôõñ
ÒÓÔÕÑ
2abcABC
3defDEF
18
1
2
3
6
Getting Started
Input Mode
Abc
2aB
Keypad
abc
(initials in
ABC
123
PQRS7Ѕ
7
capitals)
7pqrsPQR
pqrs7ßЅ
pqrs7ßЅ
tuv8ùúûü
tuv8ùúûü
wxyz9ýÞ
wxyz9ýÞ
WXYZ9ÝÞ
9
0
space
space
space
0
*.,'?!\-()@/:
*.,'?!\-()@/:
*.,'?!\-()@/:
*.,'?!\-()@/:
_;+&%=<
_;+&%=<
_;+&%=<
_;+&%=<
>
>
>
>
£$¥¤[]{}
£$¥¤[]{}
£$¥¤[]{}
£$¥¤[]{}
~^¡¿§#"|
~^¡¿§#"|
~^¡¿§#"|
~^¡¿§#"|
#
#
#
#
S
8tuvTUV
9wxyzWX
YZ
TUV8Ù Ú Û
8
Ü
.*:/@[]
#
To enter or edit data:
Do one of the following:
If you want to
Then you can
Press a keypad key one or more times
(depending what input mode you’re in) to
enter the characters that is displayed on the
keypad key.
You can press the abc soft key one or more
Enter only digits (1),
uppercase (A) characters,
lowercase (a) characters,
or alphanumeric (2aB)
characters.
times to switch among uppercase (ABC soft
key), numeric (123 soft key), alphanumeric
(2aB soft key), uppercase and lowercase (Abc
soft key) and lowercase (abc soft key) input
modes.
For example, if the input mode is ABC:
-
To enter ―A‖, press
once.
-
To enter ―B‖, press
twice quickly.
-
To enter ―C‖, press
three times
quickly.
19
User Guide for the SIP-T19(P) E2 IP Phone
If you want to
Then you can
-
To enter ―2Ä Æ Å À Á Â Ã Ç ‖, press
more than three times quickly.
Note: When you are in the uppercase (ABC
soft key), uppercase and lowercase (Abc soft
key) or lowercase (abc soft key) input mode,
is not available.
Press the keypad key
press
For
-
or
, or
.
Key:
If it is in the uppercase (ABC soft key),
uppercase and lowercase (Abc soft key)
or lowercase (abc soft key) input mode, it
will provide the space character.
-
If it is in the numeric (123 soft key) or
alphanumeric (2aB soft key) input mode,
it will only provide the digit 0.
Enter special characters.
For
-
key:
It only provides the pound character #.
For
-
key:
If it is in the uppercase (ABC soft key),
lowercase (abc soft key), uppercase and
lowercase (Abc soft key) or alphanumeric
(2aB soft key) input mode, it will provide
the following special characters:
*.,?!\-()@/:_;+&%=<>£$¥¤[]{}~^¡¿§#"|.
-
If it is in the numeric (123 soft key) input
mode, it will provide the following special
characters: .*:/@[].
Press
Delete text you entered.
or
to position the cursor to the
right of the text you want to delete, and then
press the Delete soft key to delete one
character at a time.
20
Customizing Your Phone
You can customize your SIP-T19(P) E2 IP phone by personally configuring certain settings,
for example, contrast, language and time & date. You can add contacts to the phone’s
local directory manually or from call history. You can also personalize different ring
tones for different callers.
This chapter provides basic operating instructions for customizing your phone. Topics
include:

General Settings

Audio Settings

Contact Management

Call History Management

System Customizations
If you require additional information or assistance with your new phone, contact your
system administrator.
You can configure the LCD screen contrast of SIP-T19(P) E2 to a comfortable level. The
intensity of contrast ranges from 1 to 10 and the highest intensity is 10.
To configure the contrast via phone user interface:
1.
Press Menu->Settings->Basic Settings->Display->Contrast.
2.
Press
or
, or the Switch soft key to increase or decrease the intensity of
contrast.
The default contrast level is ―6‖.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
Contrast is configurable via web user interface at the path Settings->Preference.
21
User Guide for the SIP-T19(P) E2 IP Phone
The default language of the phone user interface is English. If the language of your web
browser is not supported by the phone, the web user interface will use English by
default. You can change the language for the phone user interface and the web user
interface respectively.
To change the language for the phone user interface:
1.
Press Menu->Settings->Basic Settings->Language.
2.
Press
3.
Press the Save soft key to accept the change.
or
to select the desired language.
Text displayed on the phone user interface will change to the selected language.
To change the language for the web user interface:
1.
Click on Settings->Preference.
2.
Select the desired language from the pull-down list of Language.
3.
Click Confirm to accept the change.
Text displayed on the web user interface will change to the selected language.
22
Customizing Your Phone
The time and date are displayed on the LCD screen when the phone is idle. You can
configure the phone to obtain the time and date from the SNTP server automatically, or
configure the time and date manually. If the phone cannot obtain the time and date
from the Simple Network Time Protocol (SNTP) server, contact your system administrator
for more information.
To configure the SNTP settings via phone user interface:
1.
Press Menu->Settings->Basic Settings->Time & Date->SNTP Settings.
2.
Press
or
, or the Switch soft key to select the time zone that applies to your
area from the Time Zone field.
The default time zone is ―+8‖.
3.
Enter the domain name or IP address of SNTP server in the NTP Server1 and NTP
Server2 field respectively.
4.
Press
or
, or the Switch soft key to select the desired value from the
Daylight Saving field.
5.
Press
or
, or the Switch soft key to select the desired time zone name from
the Location field.
This field appears only if Daylight Saving field is selected Automatic.
The default time zone name is ―China(Beijing)‖.
6.
Note
Press the Save soft key to accept the change or the Back soft key to cancel.
Please refer to Appendix A - Time Zones for the list of available time zones on the IP
phone.
To configure the time and date manually via phone user interface:
1.
Press Menu->Settings->Basic Settings->Time & Date->Manual Settings.
2.
Enter the specific date in the Date(YMD) field.
23
User Guide for the SIP-T19(P) E2 IP Phone
3.
Enter the specific time in the Time(HMS) field.
4.
Press the Save soft key to accept the change.
The date and time displayed on the LCD screen will change accordingly.
To configure the time and date format via phone user interface:
1.
Press Menu->Settings->Basic Settings->Time & Date->Time & Date Format.
2.
Press
or
, or the Switch soft key to select the desired time format (12 Hour
or 24 Hour) from the Time Format field.
3.
Press
or
, or the Switch soft key to select the desired date format from the
Date Format field.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
There are 7 available date formats. For example, for the date format ―WWW DD MMM‖,
―WWW‖ represents the abbreviation of the weekday, ―DD‖ represents the two-digit day,
and ―MMM‖ represents the first three letters of the month.
The date formats available:
Date Format
Example (2015-04-29)
WWW MMM DD
Wed Apr 29
DD-MMM-YY
29-Apr-15
YYYY-MM-DD
2015-04-29
DD/MM/YYYY
29/04/2015
MM/DD/YY
04/29/15
DD MMM YYYY
29 Apr 2015
WWW DD MMM
Wed 29 Apr
Time and date are configurable via web user interface at the path Settings->Time &
Date.
24
Customizing Your Phone
The Advanced Settings option is only accessible to the administrator. The default
administrator password is ―admin‖. For security reasons, you should change the default
administrator password as soon as possible.
To change the administrator password via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin) ->Set
Password.
2.
Enter the current password in the Current PWD field.
3.
Enter the new password in the New PWD field.
4.
Re-enter the new password in the Confirm PWD field.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
Administrator password is configurable via web user interface at the path
Security->Password.
You can set the ―#‖ key or ―*‖ key to perform as a send key while dialing.
To configure key as send via phone user interface:
1.
Press Menu->Features->Key as send.
2.
Press
or
, or the Switch soft key to select # or * from the Key as send field,
or select Disabled to disable this feature.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
Key as send is configurable via web user interface at the path Features->General
Information.
25
User Guide for the SIP-T19(P) E2 IP Phone
You can lock your phone temporarily when you are not using it. This feature helps to
protect your phone from unauthorized use.
Phone lock consists of the following:
Menu Key:
The Menu soft key is locked. You cannot access the menu of the
phone until unlocked.
Function Keys:
The function keys are locked. You cannot use the Message, RD,
Mute, Transfer,
, navigation keys and soft keys until
unlocked.
All Keys:
All keys are locked except the Volume key, digit keys, # key, * key
and Speakerphone key. You are only allowed to dial emergency
numbers, reject incoming calls by pressing the Reject soft key,
answer incoming calls by lifting the handset, pressing the
Speakerphone key, the HEADSET key, the
key, or the Answer
soft key, and end the call by hanging up the handset, pressing
the Speakerphone key or the EndCall soft key.
Note
The emergency number setting, if desired, must be set before lock activation. For more
information, refer to Emergency Number on page 63.
To activate the phone lock via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin) ->Phone
Lock.
2.
Press
or
, or the Switch soft key to select Enabled from the Lock Enable
or
, or the Switch soft key to select the desired type from the Lock
field.
3.
Press
Type field.
26
Customizing Your Phone
4.
(Optional.) Enter the desired interval of automatic phone lock in the Lock Time Out
field.
The default timeout is 0. It means the phone will not be automatically locked. You
need to long press
to lock it immediately when the phone is idle.
If it is set to other values except 0 (e.g., 5), the phone will be locked when the phone
is inactive in idle screen for the designated time (in seconds).
5.
Press the Save soft key to accept the change.
When the phone is locked, the LCD screen prompts ―Phone locked.‖ and displays
the icon
.
To unlock the phone, you must know the phone unlock PIN. The default phone unlock PIN
is ―123‖.
To unlock the phone via phone user interface:
1.
Press any locked key, the LCD screen prompts ―Unlock PIN‖.
2.
Enter the PIN in the Unlock PIN field.
3.
Press the OK soft key to unlock the phone.
The
icon disappears from the LCD screen.
You can long press
or wait for a period of time (if configured) to lock the
phone again.
Note
You can also unlock the phone by administrator password. When you enter the
administrator password to unlock the phone, the phone will turn to the Change PIN
screen.
27
User Guide for the SIP-T19(P) E2 IP Phone
To change the phone unlock PIN via phone user interface:
1.
Press Menu->Settings->Basic Settings->Change PIN.
2.
Enter the desired value in the Current PIN, New PIN and Confirm PIN field
respectively.
3.
Note
Press the Save soft key to accept the change or the Back soft key to cancel.
The unlock PIN length must be within 15 digits.
To deactivate the phone lock via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin) ->Phone
Lock.
2.
Press
or
, or the Switch soft key to select Disabled from Lock Enable field.
3.
Press the Save soft key to accept the change.
Phone lock is configurable via web user interface at the path Features->Phone Lock.
You can press the Volume key to adjust the ringer volume when the phone is idle or
ringing. You can also press the Volume key to adjust the receiver volume of currently
engaged audio devices (handset, speakerphone or headset) when the phone is in use.
28
Customizing Your Phone
To adjust the ringer volume:
When the phone is idle:
1.
Press
to adjust the ringer volume.
When the phone is ringing:
1.
Press
You can also press
to adjust the ringer volume.
to adjust the ringer volume when selecting a ring tone.
For more information, refer to Ring Tones on page 29.
Note
If the ringer volume is adjusted to minimum, the
icon will appear on the LCD screen.
To adjust the volume when the phone is during a call:
1.
Press
to adjust the volume of currently engaged audio device
(handset, speakerphone or headset).
Ring tones are used to indicate incoming calls. You can select different ring tones to
distinguish your phone from your neighbor’s.
To select a ring tone for the phone via phone user interface:
1.
Press Menu->Settings->Basic Settings->Sound->Ring Tones->Common.
29
User Guide for the SIP-T19(P) E2 IP Phone
2.
Press
or
to select the desired ring tone.
3.
(Optional.) Press
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
to adjust the ringer volume.
A ring tone for the phone is configurable via web user interface at the path
Settings->Preference->Ring Type.
To select a ring tone for the account via phone user interface:
1.
Press Menu->Settings->Basic Settings->Sound->Ring Tones.
2.
Press
or
to select the desired account and then press the Enter soft key.
3.
Press
or
to select the desired ring tone.
If Common is selected, this account will use the ring tone selected for the phone.
4.
(Optional.) Press
to adjust the ringer volume.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
A ring tone for the account is configurable via web user interface at the path
Account->Basic->Ring Type.
To upload a custom ring tone for your phone via web user interface:
1.
30
Click on Settings->Preference.
Customizing Your Phone
2.
In the Upload Ringtone field, click Browse to locate a ring tone (the file format must
be *.wav) file from your local system.
3.
Note
Click Upload to upload the file.
The priority of ring tone for an incoming call on the phone is as follows:
Contact ring tone (refer to Adding Contacts) >Group ring tone (refer to Adding
Groups) >Account ring tone >Phone ring tone.
Both single custom ring tone file and total custom ring tone files must be within 100KB.
Uploading custom ring tones for your phone is configurable via web user interface only.
This section provides the operating instructions for managing contacts. Topics include:

Directory

Local Directory

Blacklist

Remote Phone Book
Directory provides easy access to frequently used lists. The lists may contain Local
Directory, History and Remote Phone Book.
To configure the directory via web user interface:
1.
Click on Directory->Setting.
31
User Guide for the SIP-T19(P) E2 IP Phone
2.
In the Directory block, select the desired list from the Disabled column and then
click
.
The selected list appears in the Enabled column.
3.
Repeat the step 2 to add more lists to the Enabled column.
4.
To remove a list from the Enabled column, select the desired list and then click
5.
To adjust the display order of enabled lists, select the desired list and then click
or
.
The LCD screen displays the list(s) in the adjusted order.
6.
Note
Click Confirm to accept the change.
Directory is configurable via web user interface only.
To check the directory via phone user interface:
1.
Press the Dir soft key when the phone is idle.
The LCD screen displays the enabled list(s) in the directory.
If there is only one list in the directory, press the Dir soft key to enter this list directly.
Note
32
If the remote phone book is not configured in advance, you cannot see remote phone
book list on the phone user interface. For more information on remote phone book, refer
to Remote Phone Book on page 44.
.
Customizing Your Phone
The built-in phone directory can store the names and phone numbers of your contacts.
You can store up to 1000 contacts and 48 groups in your phone's local directory. You can
add new groups and contacts, edit, delete or search for a contact, or simply dial a
contact number from the local directory.
To add a group to the local directory:
1.
Press the Dir soft key.
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
press Menu->Directory->Local Directory to enter the local directory.
2.
Press the AddGr soft key.
3.
Enter the desired group name in the Name field.
4.
Press
or
, or Switch soft key to select the desired group ring tone from the
Ring field.
If Auto is selected, this group will use the ring tone according to the priority: Contact
ring tone (refer to Adding Contacts) >Account ring tone (refer to Ring
Tones) >Phone ring tone (refer to Ring Tones). If a specific ring tone is selected, this
group will use the ring tone according to the priority: Contact ring tone (refer to
Adding Contacts) >Group ring tone.
5.
Press the Add soft key to accept the change or the Back soft key to cancel.
You can also edit or delete any newly added contact groups.
33
User Guide for the SIP-T19(P) E2 IP Phone
To edit a group in the local directory:
1.
Press the Dir soft key.
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
press Menu->Directory->Local Directory to enter the local directory.
2.
Select the desired group.
3.
Press the Option soft key, and then select Detail.
4.
Press
5.
Press the Save soft key to accept change or the Back soft key to cancel.
or
to scroll through the group information and then edit.
To delete a group from the local directory:
1.
34
Press the Dir soft key.
Customizing Your Phone
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
press Menu->Directory->Local Directory to enter the local directory.
2.
Select the desired group.
3.
Press the Option soft key, and then select Delete.
The LCD screen prompts the following warning:
4.
Press the OK soft key to confirm the deletion or the Cancel soft key to cancel.
You can also delete all groups by pressing the Option soft key and then select Delete
All.
You can add contacts to the local directory in the following ways:

Manually

From call history

From a remote phone book
Adding Contacts Manually
To add a contact to the local directory manually:
1.
Press the Dir soft key.
35
User Guide for the SIP-T19(P) E2 IP Phone
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
press Menu->Directory->Local Directory to enter the local directory.
2.
Select the desired contact group and then press the Enter soft key.
If the contact is not in any group, select All Contacts and then press the Enter soft
key.
3.
Press the Add soft key.
4.
Enter the name and the office, mobile or other numbers in the corresponding fields.
5.
Press
or
, or the Switch soft key to select the desired ring tone from the
Ring field.
If Auto is selected, this contact will use the ring tone according to the priority:
Group ring tone (refer to Adding Groups) >Account ring tone (refer to Ring
Tones)>Phone ring tone (refer to Ring Tones).
6.
Press
or
, or the Switch soft key to select the desired group from the Group
field.
7.
Note
Press the Add soft key to accept the change or the Back soft key to cancel.
If the contact has existed in the directory, the LCD screen will prompt ―Contact name
existed!‖.
Adding Contacts from Call History
To add a contact to the local directory from the call history:
36
1.
Press the History soft key.
2.
Press
or
to highlight the desired entry.
Customizing Your Phone
3.
Press the Option soft key, and then select Add to Contacts.
4.
Press the OK soft key, and then edit the contact name.
5.
Press the Save soft key to accept the change.
The entry is successfully saved to the local directory.
Adding Contacts from Remote Phone Book
To add a contact to the local directory from remote phone book:
1.
Press Menu->Directory->Remote Phone Book.
If Remote Phone Book is added to the directory (refer to Directory on page 31),
press Dir->Remote Phone Book to enter the remote phone book.
2.
Select the desired remote group and then press the Enter soft key.
3.
Press
4.
Press the Option soft key, and then select Add to Contacts.
5.
Press the Save soft key to save the contact in the local directory.
or
to highlight the desired entry.
If the contact has already existed in the local directory, the LCD screen will prompt
―Contact name existed, overwrite?‖. Press the OK soft key to overwrite the original
contact in local directory or the Cancel soft key to cancel.
For more information on remote phone book operating, refer to Remote Phone Book on
page 44.
To edit a contact in the local directory:
1.
Press the Dir soft key.
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
37
User Guide for the SIP-T19(P) E2 IP Phone
press Menu->Directory->Local Directory to enter the local directory.
2.
Select the desired contact group and then press the Enter soft key.
If the contact is not in any group, select All Contacts and then press the Enter soft
key.
3.
Press
or
4.
Press the Option soft key, and then select Detail.
5.
Press
6.
Press the Save soft key to accept change or the Back soft key to cancel.
or
to highlight the desired contact.
to highlight the contact information and then edit.
To delete a contact from the local directory:
1.
Press the Dir soft key.
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
press Menu->Directory->Local Directory to enter the local directory.
2.
Select the desired contact group and then press the Enter soft key.
If the contact is not in any group, select All Contacts and then press the Enter soft
key.
38
3.
Press
or
to highlight the desired contact.
4.
Press the Option soft key, and then select Delete.
Customizing Your Phone
The LCD screen prompts the following warning:
5.
Press the OK soft key to confirm the deletion or the Cancel soft key to cancel.
You can also delete all contacts by pressing the Option soft key, and then select Delete
All.
To place a call to a contact from the local directory:
1.
Press the Dir soft key.
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
press Menu->Directory->Local Directory to enter the local directory.
2.
Select the desired contact group and then press the Enter soft key.
If the contact is not in any group, select All Contacts and then press the Enter soft
key.
3.
Press
4.
Do one of the following:
-
or
to highlight the desired contact.
If only one number of the contact is stored in the local directory, press the Send
soft key to dial out the number.
-
If multiple numbers of the contact are stored in the local directory, press the
Send soft key to display a list of numbers.
Press
or
to highlight the desired number.
Press the Send soft key to dial out the number.
39
User Guide for the SIP-T19(P) E2 IP Phone
To search for a contact in the local directory:
1.
Press the Dir soft key.
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
press Menu->Directory->Local Directory to enter the local directory.
2.
Press the Search soft key.
3.
Enter a few continuous characters of the contact name or continuous numbers of
the contact number (office, mobile or other number) using the keypad.
The contacts whose name or phone number matches the characters entered will
appear on the LCD screen. You can dial from the result list.
You can search for a contact from the desired lists when the phone is on the dialing
screen. The lists can be Local Directory, History and Remote Phone Book.
To configure search source list in dialing via web user interface:
1.
Click on Directory->Setting.
2.
In the Search Source List In Dialing block, select the desired list from the Disabled
column and then click
.
The selected list appears in the Enabled column.
3.
Repeat the step 2 to add more lists to the Enabled column.
4.
To remove a list from the Enabled column, select the desired list and then click
5.
To adjust the display order of search results, select the desired list and then click
or
40
.
.
Customizing Your Phone
The LCD screen will display search results in the adjusted order.
6.
Note
Click Confirm to accept the change.
Search source list in dialing is configurable via web user interface only.
To search for a contact in the enabled search source lists:
1.
Pick up the handset, press the Speakerphone key.
2.
Enter a few continuous characters of the entry’s name or continuous numbers of the
entry’s phone number (office, mobile or other number) using the keypad.
The entries in the enabled search source lists whose name or phone number
matches the characters entered will appear on the LCD screen. You can press
or
to scroll to the desired entry, and then place a call to the entry.
You can manage your phone’s local directory via phone user interface or web user
interface. But you can only import or export the contact list via web user interface.
To import an XML file of contact list via web user interface:
1.
Click on Directory->Local Directory.
41
User Guide for the SIP-T19(P) E2 IP Phone
2.
Click Browse to locate a contact list file (the file format must be *.xml) from your
local system.
3.
Click Import XML to import the contact list.
The web user interface prompts ―The original contact will be covered, continue?‖.
4.
Click OK to complete importing the contact list.
To import a CSV file of contact list via web user interface:
1.
Click on Directory->Local Directory.
2.
Click Browse to locate a contact list file (file format must be *.csv) from your local
system.
3.
(Optional.) Check the Show Title checkbox.
It will prevent importing the title of the contact information which is located in the
first line of the CSV file.
4.
Click Import CSV to import the contact list.
5.
(Optional.) Mark the On radio box in the Delete Old Contacts field.
It will delete all existing contacts while importing the contact list.
6.
Select the contact information you want to import into the local directory from the
pull-down list of Index.
42
Customizing Your Phone
At least one item should be selected to be imported into the local directory.
7.
Click Import to complete importing the contact list.
To export a contact list via web user interface:
1.
Click on Directory->Local Directory.
2.
Click Export XML (or Export CSV).
3.
Click Save to save the contact list to your local system.
Note
Importing/exporting contact lists is available via web user interface only.
The built-in phone directory can store names and phone numbers for a blacklist. You
can store up to 30 contacts, add, edit, delete or search for a contact in the blacklist
directory, and even call a contact from the blacklist directory. Incoming calls from
blacklist directory contacts will be rejected automatically.
To add a contact to the blacklist directory manually:
1.
Press Menu->Directory->Blacklist.
2.
Press the Add soft key.
3.
Enter the name and the office, mobile or other numbers in the corresponding fields.
43
User Guide for the SIP-T19(P) E2 IP Phone
4.
Press the Add soft key to accept the change or the Back soft key to cancel.
To add a contact to the blacklist directory from the local directory:
1.
Press the Dir soft key.
The IP phone enters the local directory directly as there is only Local Directory
enabled in the directory by default.
If Local Directory is removed from the directory (refer to Directory on page 31),
press Menu->Directory->Local Directory to enter the local directory.
2.
Select the desired contact group and then press the Enter soft key.
If the contact is not in any group, select All Contacts and then press the Enter soft
key.
3.
Press
or
to highlight the desired contact.
4.
Press the Option soft key and then select Add to Blacklist.
The LCD screen prompts the following warning:
5.
Press the OK soft key to accept the change.
For operating instructions on editing, deleting, placing calls to and/or searching for
contacts in the blacklist directory, refer to the operating instructions of Local Directory on
page 33.
You can add new contacts to the local directory, search for a contact, or simply dial a
contact number from the remote phone book.
You can configure your new phone to access up to 5 remote phone books. For the
access URL of the remote phone book, contact your system administrator.
44
Customizing Your Phone
To configure an access URL for a remote phone book via web user interface:
1.
Click on Directory->Remote Phone Book.
2.
Enter the access URL in the Remote URL field.
3.
Enter the name in the Display Name field.
4.
Click Confirm to accept the change.
Note
An access URL for a remote phone book is configurable via web user interface only.
To access your remote phone book via phone user interface:
1.
Press Menu->Directory->Remote Phone Book.
If Remote Phone Book is added to the directory (refer to Directory on page 31),
press Dir->Remote Phone Book to enter the remote phone book.
2.
Press
or
to select the desired remote group, and then press the Enter soft
key.
The phone then connects to the remote phone book and proceeds to load it. The
contacts in the remote phone book are displayed on the LCD screen.
3.
Press the Back soft key to back to the previous screen.
45
User Guide for the SIP-T19(P) E2 IP Phone
To place a call from the remote phone book:
1.
Press Menu->Directory->Remote Phone Book.
If Remote Phone Book is added to the directory (refer to Directory on page 31),
press Dir->Remote Phone Book to enter the remote phone book.
2.
Select the desired remote group, and then press the Enter soft key to load the
remote phone book.
3.
Select the desired contact in the remote phone book.
4.
Press the Send soft key.
To search for a contact in the remote phone book:
1.
Press Menu->Directory->Remote Phone Book.
If Remote Phone Book is added to the directory (refer to Directory on page 31),
press Dir->Remote Phone Book to enter the remote phone book.
2.
Select the desired remote group, and then press the Enter soft key to load the
remote phone book.
3.
Press the Search soft key.
4.
Press the Abc soft key to change the input mode. And then enter a few continuous
characters of the contact name or continuous numbers of the contact number using
the keypad.
The contacts whose name or phone number matches the characters entered will
appear on the LCD screen. You can place a call from the result list.
You can enable the phone to present the caller/callee identity stored in the remote
phone book when receiving/placing a call.
To configure incoming/outgoing call lookup and update time interval via web user
interface:
46
1.
Click on Directory->Remote Phone Book.
2.
Select Enabled from the pull-down list of Incoming/Outgoing Call Lookup.
Customizing Your Phone
3.
Enter the desired refresh period in the Update Time Interval(Seconds) field.
The default value is 21600.
4.
Click Confirm to accept the change.
The SIP-T19(P) E2 IP phone maintains call history lists of Placed calls, Received calls,
Missed calls and Forwarded calls. Each call history list supports up to 100 entries. You
can view call history, place a call, add a contact or delete an entry from the call history
list.
History record feature is enabled by default. If you don’t want to save the call history,
you can disable the feature.
To disable history record via phone user interface:
1.
Press Menu->Features->History Setting.
2.
Press
or
, or the Switch soft key to select Disabled from the History Record
field.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
To view the call history:
1.
Press the History soft key.
The LCD screen displays all call records.
2.
Press
or
to switch among All Calls, Placed Calls, Received Calls, Missed
Calls and Forwarded Calls.
47
User Guide for the SIP-T19(P) E2 IP Phone
3.
Press
or
to select the desired entry.
4.
Press the Option soft key, and then select Detail.
The detailed information of the entry appears on the LCD screen.
To place a call from the call history list:
1.
Press the History soft key.
2.
Press
or
to switch among All Calls, Placed Calls, Received Calls, Missed
Calls and Forwarded Calls.
3.
Press
or
to select the desired entry.
4.
Press the Send soft key.
To add a contact to the local directory (or blacklist directory) from the call history list:
1.
Press the History soft key.
2.
Press
or
to switch among All Calls, Placed Calls, Received Calls, Missed
Calls and Forwarded Calls.
3.
Press
or
to select the desired entry.
4.
Press the Option soft key, and then select Add to Contacts (or Add to Blacklist).
5.
Enter the desired values in the corresponding fields.
6.
Press the Save soft key.
For more information, refer to Contact Management on page 31.
To delete an entry from the call history list:
1.
Press the History soft key.
2.
Press
or
to switch among All Calls, Placed Calls, Received Calls, Missed
Calls and Forwarded Calls.
3.
Press
or
to select the desired entry.
4.
Press the Delete soft key.
To delete all entries from the call history list:
1.
Press the History soft key.
2.
Press
or
to switch among All Calls, Placed Calls, Received Calls, Missed
Calls and Forwarded Calls.
48
3.
Press the Option soft key, and then select Delete All.
4.
Press the OK soft key.
Customizing Your Phone
The LCD screen prompts "Delete all the call records?".
5.
Press the OK soft key to confirm the deletion or the Cancel soft key to cancel.
You can upload your custom logo which will be shown on the idle screen.
To upload a custom logo via web user interface:
Note
1.
Click on Features->General Information.
2.
Select Custom logo from the pull-down list of Use Logo.
3.
Click Browse to locate the logo file from your local system.
4.
Click Upload to upload the file.
Delete item will appear after you upload a custom logo, you can click Delete to delete
the custom logo.
The logo file format must be *.dob, contact your system administrator for more
information.
A custom logo can be uploaded via web user interface only.
49
User Guide for the SIP-T19(P) E2 IP Phone
If you want to use a headset, physically connect your headset and activate the headset
mode for use. For more information on physically connecting a headset, refer to Phone
Installation on page 11.
To activate the headset mode:
1.
Press
on the phone.
The headset icon on the idle screen indicates that the headset mode is activated.
Press the Answer soft key to answer an incoming call. The call will be connected to
your headset automatically.
Enter the desired number and then press the Send soft key, the phone will then
place a call using the headset automatically. For more information on using the
headset to place a call, refer to Placing Calls on page 67.
To deactivate the headset mode:
1.
Press
again on the phone.
The headset icon disappears from the idle screen indicates the headset mode is
deactivated.
You can use headset in priority when headset prior feature is enabled. This feature is
especially useful for permanent or full-time headset users.
To enable headset prior via web user interface:
1.
50
Click on Features->General Information.
Customizing Your Phone
2.
Select Enabled from the pull-down list of Headset Prior.
3.
Click Confirm to accept the change.
To use headset prior feature, you should activate the headset mode in advance:
Note
1.
Physically connect the headset.
2.
Press
to activate the headset mode.
If headset prior is enabled, the headset mode will not be deactivated until you press the
Headset key again.
If headset prior is disabled, the headset mode can be deactivated by pressing the
Speakerphone key or the Headset key.
Headset prior is configurable via web user interface only.
You can use two headsets when enabling dual headset. To use this feature, you must
physically connect headsets to the headset jack and handset jack respectively. Once
the phone connects to a call, the headset connected to the headset jack will have
full-duplex capabilities, while the one connected to the handset jack will only be able to
listen.
To enable dual headset via web user interface:
1.
Click on Features->General Information.
51
User Guide for the SIP-T19(P) E2 IP Phone
2.
Select Enabled from the pull-down list of Dual-Headset.
3.
Click Confirm to accept the change.
Note
Dual headset is configurable via web user interface only.
You can customize the soft keys, navigation keys and function keys on the keypad. The
SIP-T19(P) E2 IP phone supports 11 programable keys.
To customize the programable keys via web user interface:
1.
52
Click on DSSKey->Programable Key.
Customizing Your Phone
2.
Customize specific features for these keys.
3.
(Optional.) Enter the string that will appear on the LCD screen in the Label field.
Label is configurable only when customizing SoftKey (1-4).
4.
Click Confirm to accept the change.
You can click Reset to default to reset custom settings to defaults.
Note
Programable keys are configurable via web user interface only.
Common used programable key features are explained in the following subchapters in
detail:

Speed Dial

Direct Pickup

Group Pickup

Prefix

Local Directory

Local Group

XML Directory

XML Group

XML Browser

SMS

New SMS

Zero Touch

Phone Lock

Directory
53
User Guide for the SIP-T19(P) E2 IP Phone
For the features not listed above, refer to Basic Call Features on page 67 and Advanced
Phone Features on page 97. For more information, contact your system administrator.
Speed Dial
You can use this key feature to speed up dialing numbers frequently used or hard to
remember.
Dependencies: Type (Speed Dial)
Value (the number you want to dial out)
Label (key label displayed on the LCD screen)
Usage: Press the programable key to dial out the number specified in the Value field.
Direct Pickup
You can use this key feature to answer someone else’s incoming call on the phone.
Dependencies: Type (Direct Pickup)
Value (the direct pickup code followed by the specific phone number)
Label (key label displayed on the LCD screen)
Usage: Press the programable key on your phone when the target phone number
receives an incoming call. The call is then answered on your phone.
Group Pickup
You can use this key feature to answer incoming calls in a group that is associated with
their own group.
Dependencies: Type (Group Pickup)
Value (the group pickup feature code)
Label (key label displayed on the LCD screen)
Usage: Press the programable key on your phone when a phone number in the group
receives an incoming call. The call is answered on your phone.
Prefix
You can use this key feature to add a specified prefix number before the dialed number.
You can only configure the SoftKey (1-4) as the prefix key.
Dependencies: Type (Prefix)
Value (the prefix number)
Label (key label displayed on the LCD screen)
Usage: Press the programable key when the phone is idle, then the phone will enter into
the dialing screen and display the prefix number which you specified in the Value field.
You can enter remaining digits and then dial out.
Local Directory
You can use this key feature to access the local directory quickly. For more information,
refer to Local Directory on page 33.
54
Customizing Your Phone
Dependencies: Type (Local Directory)
Label (key label displayed on the LCD screen)
Usage: Press the programable key to access the local directory quickly.
Local Group
You can use this key feature to access the group in the local directory quickly. For more
information, refer to Local Directory on page 33.
Dependencies: Type (Local Group)
Line (the contact group you want to access)
Label (key label displayed on the LCD screen)
Usage: Press the programable key to access the contact group specified in the Line
field.
XML Directory
You can use this key feature to access the corporate directory quickly. For more
information, refer to Remote Phone Book on page 44.
Dependencies: Type (XML Directory)
Label (key label displayed on the LCD screen)
Usage: Press the programable key to access the corporate directory quickly.
XML Group
You can use this key feature to access the remote group in your remote phone book
quickly. You should configure remote phone book in advance. For more information,
refer to Remote Phone Book on page 44.
Dependencies: Type (XML Group)
Line (the remote group you want to access if the remote phone book is
configured)
Label (key label displayed on the LCD screen)
Usage: Press the programable key to access the remote group specified in the Line
field.
XML Browser
You can use this key feature to access an XML browser quickly. The XML browser allows
you to create custom services which meet your functional requirements on the server.
You can customize practical applications, such as weather report, stock information,
Google search, etc.
Dependencies: Type (XML Browser)
Value (the access URL for xml browser)
Label (key label displayed on the LCD screen)
Usage: Press the programable key to access the XML browser specified in the Value
field.
55
User Guide for the SIP-T19(P) E2 IP Phone
SMS
You can use this key feature to quick access text message. For more information, refer to
Short Message Service (SMS) on page 117.
Dependencies: Type (SMS)
Label (key label displayed on the LCD screen)
Usage: Press the programable key when the phone is idle to access the text message.
New SMS
You can use this key feature to quick access the new text message. For more information,
refer to Short Message Service (SMS) on page 117.
Dependencies: Type (New SMS)
Label (key label displayed on the LCD screen)
Usage: Press the programable key when the phone is idle to access the New Message
screen. You can enter the text message and then send it.
Zero Touch
You can use this key feature to configure auto provision and network parameters quickly.
Dependencies: Type (Zero Touch)
Label (key label displayed on the LCD screen)
Usage:
1.
Press the programable key to access the zero touch screen.
2.
Press the OK soft key in a few seconds.
3.
Configure the network parameters in the corresponding fields.
4.
Press the Next soft key.
5.
Configure the auto provision parameters in the corresponding fields.
6.
Press the OK soft key.
The phone will reboot to update configurations.
Phone Lock
You can use this key feature to immediately lock your phone instead of long
pressing
. For more information, refer to Phone Lock on page 26.
Dependencies: Type (Phone Lock)
Label (key label displayed on the LCD screen)
Usage: When the phone lock feature is enabled, press the programable key to
immediately lock your phone instead of long pressing
.
Directory
You can use this key feature to easily access frequently used lists. For more information,
refer to Directory on page 31.
56
Customizing Your Phone
Dependencies: Type (Directory)
Label (key label displayed on the LCD screen)
Usage: Press the programable key to immediately access to frequently used lists.
You can only register one account on the SIP-T19(P) E2 IP phone.
To register an account via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin)
->Accounts.
2.
Press the Enter soft key.
3.
Press
or
, or the Switch soft key to select Enabled from the Active Line
field.
4.
Enter the desired value in Label, Display Name, Register Name, User Name,
Password and SIP Server1/2 field respectively. Contact your system administrator
for more information.
5.
If you use the outbound proxy servers, do the following:
1)
Press
or
, or the Switch soft key to select Enabled from the Outbound
Status field.
2)
Enter the desired value in the Outbound Proxy1/2 and Proxy Fallback Interval
field respectively. Contact your system administrator for more information.
6.
Press the Save soft key to accept the change or the Back soft key to cancel.
To disable an account via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin)
->Accounts.
2.
Press
or
, or the Switch soft key to select Disabled from the Active Line
field.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
Account registration is configurable via web user interface at the path
Account->Register.
57
User Guide for the SIP-T19(P) E2 IP Phone
Dial plan is a string of characters that governs the way your SIP-T19(P) E2 IP phone
processes the inputs received from your phone keypad. The SIP-T19(P) E2 IP phone
supports the following dial plan features:

Replace Rule

Dial-now

Area Code

Block Out
The basic expression syntax you need to know:
The dot "." can be used as a placeholder or multiple placeholders for
.
any character. Example:
"12." would match "123", "1234", "12345", "12abc", etc.
x
An "x" can be used as a placeholder for any character. Example:
"12x" would match "121", "122", "123", "12a", etc.
Numeric ranges are allowed within the brackets: Digit ―-‖ Digit.
-
Example:
―[5-7]‖ would match the number‖5‖, ‖6‖or ‖7‖.
The square brackets "[]" can be used as a placeholder for a single
[]
character which matches any of a set of characters. Example:
"91[5-7]1234" would match "9151234", "9161234", "9171234".
The parentheses "( )" can be used to group together patterns, for
()
instance, to logically combine two or more patterns. Example:
"([1-9])([2-7])3" would match "923", "153", "773", etc.
The ―$‖ should be followed by the sequence number of a parenthesis.
The ―$‖ plus the sequence number means the whole character or
characters placed in the parenthesis. The number directs to the right
parenthesis when there are more than one. Example:
$
A replace rule configuration, Prefix: "001(xxx)45(xx)", Replace:
"9001$145$2". When you dial out "0012354599" on your phone, the IP
phone will replace the number with "90012354599". ―$1‖ means 3 digits
in the first parenthesis, that is, ―235‖. ―$2‖ means 2 digits in the second
parenthesis, that is, ―99‖.
You can configure one or more replace rules (up to 100) to remove the specified string
and replace it with another string. You can configure a pattern with wildcards (refer to
the expression syntax in the table above), so that any string that matches the pattern
will be replaced. This feature is convenient for you to dial out a long number. For
example, a replace rule is configured as ―Prefix: 1‖ and ―Replace: 1234‖. When trying to
58
Customizing Your Phone
dial out the number ―1234‖, you just need to enter ―1‖ on the phone and then press the
Send soft key.
To add a replace rule via web user interface:
1.
Click on Settings->Dial Plan->Replace Rule.
2.
Enter the string (e.g., 1) in the Prefix field.
3.
Enter the string (e.g., 1234) in the Replace field.
4.
Click Add to add the replace rule.
When you enter the number ―1‖ using the keypad and then press the Send soft key,
the phone will dial out ―1234‖ instead.
To edit a replace rule via web user interface:
1.
Click on Settings->Dial Plan->Replace Rule.
2.
Select the desired replace rule by checking the check box.
3.
Edit the values in the Prefix and Replace fields.
4.
Click Edit to accept the change.
To delete one or more replace rules via web user interface:
Note
1.
Click on Settings->Dial Plan->Replace Rule.
2.
Select one or more replace rules by checking the check box(es).
3.
Click Del to delete the replace rule(s).
Replace rule is configurable via web user interface only.
59
User Guide for the SIP-T19(P) E2 IP Phone
You can configure one or more dial-now rules (up to 100) on your phone. When the
dialed number matches the dial-now string, the number will be dialed out automatically.
For example, a dial-now rule is configured as "1xx", any entered three-digit string
beginning with 1 will then be dialed out automatically on the phone.
To add a dial-now rule via web user interface:
1.
Click on Settings->Dial Plan->Dial-now.
2.
Enter the desired value (e.g., 1xx) in the Rule field.
3.
Click Add to add the dial-now rule.
When you enter the number ―123‖ using the keypad, the phone will dial out ―123‖
automatically without pressing any key.
Note
You can also edit or delete the dial-now rule, refer to Replace Rule on page 58 for more
information.
Dial-now rule is configurable via web user interface only.
Delay Time for Dial-now Rule
You can configure the delay time for dial-now rules. That is, you can configure your
phone to automatically dial out the phone number which matches a dial-now rule, after
the designated delay time.
To configure the delay time for dial-now rule via web user interface:
1.
60
Click on Features->General Information.
Customizing Your Phone
2.
Enter the time between 0 and 14 (seconds) in the Time-Out for Dial-Now Rule field.
3.
Click Confirm to accept the change.
Note
Delay time for dial-now rule is configurable via web user interface only.
Area codes are also known as Numbering Plan Areas (NPAs). They usually indicate
geographical areas in a country. This feature is necessary when dialing a phone
number outside the code area. For example, an area code is configured as "Code: 0592,
Min Length: 1, Max Length: 15". When you dial out the number "56789" (the length of the
number is between 1 and 15), the phone will add the area code and dial out the
number "059256789". You can only configure one area code rule on your phone.
To configure the area code via web user interface:
1.
Click on Settings->Dial Plan->Area Code.
61
User Guide for the SIP-T19(P) E2 IP Phone
2.
Enter the desired values in the Code, Min Length (1-15) and Max Length (1-15)
fields.
3.
Note
Click Confirm to accept the change.
The default value of minimum and maximum length is 1 and 15 respectively.
Area code is configurable via web user interface only.
You can block some specific numbers (up to 10) from being dialed on your phone. When
you dial a block out number on your phone, the dialing will fail and the LCD screen will
prompt "Forbidden Number".
To add a block out number via web user interface:
1.
62
Click on Settings->Dial Plan->Block Out.
Customizing Your Phone
2.
Enter the desired value in the BlockOut Number field.
3.
Click Confirm to add the block out number.
Block out number is configurable via web user interface only.
Note
Public telephone networks in countries around the world have a single emergency
telephone number (emergency services number), that allows a caller to contact local
emergency services for assistance when necessary. The emergency telephone number
may differ from country to country. It is typically a three-digit number so that it can be
easily remembered and dialed quickly. Some countries have a different emergency
number for each of the different emergency services.
You can specify the emergency telephone numbers on the IP phone for contacting the
emergency services in an emergency situation. You can dial these numbers when the
phone is locked. For more information on phone lock, refer to Phone Lock on page 26.
Note
Contact your local phone service provider for available emergency numbers in your
area.
To specify emergency numbers via web user interface:
1.
Click on Features->Phone Lock.
2.
Enter the emergency number in the Emergency field.
63
User Guide for the SIP-T19(P) E2 IP Phone
For multiple numbers, enter a comma between every two emergency numbers. The
default emergency numbers are 112, 911, 110.
3.
Note
Click Confirm to accept the change.
Emergency number is configurable via web user interface only.
You can enable live dialpad feature on the SIP-T19(P) E2 IP phone, which enables the IP
phone to automatically dial out a phone number without pressing the send key. You can
also configure a delay, and then the phone will dial out the phone number
automatically after the designated period of time.
To enable live dialpad via web user interface:
64
1.
Click on Settings->Preference.
2.
Select Enabled from the pull-down list of Live Dialpad.
3.
Enter the desired delay time in the Inter Digit Time(1~14s) field.
Customizing Your Phone
The default delay time is 4 seconds.
4.
Note
Click Confirm to accept the change.
Live dialpad is configurable via web user interface only.
You can dial a hotline number immediately upon lifting the handset, pressing the
Speakerphone key. You can also configure a delay, and then the phone will dial out the
hotline number automatically after the designated period of time.
To configure the hot line number via phone user interface:
1.
Press Menu->Features->Hot Line.
2.
Enter the desired number in the Hot Number field.
3.
Enter the delay time in the Hotline Delay field.
The valid values range from 0 to 10 (seconds) and the default value is ―4‖.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
Hotline is configurable via web user interface at the path Features->General
Information.
65
User Guide for the SIP-T19(P) E2 IP Phone
66
Basic Call Features
The SIP-T19(P) E2 IP phone is designed to be easily used like a regular phone on a public
switched telephone network (PSTN). You can place calls, answer calls, transfer a call to
someone else, or conduct a conference call.
This chapter provides basic operating instructions for the SIP-T19(P) E2 IP phone. Topics
include:

Placing Calls

Answering Calls

Ending Calls

Redialing Numbers

Recent Call In Dialing

Auto Answer

Auto Redial

Call Completion

ReCall

Call Mute

Call Hold/Resume

Do Not Disturb (DND)

Call Forward

Call Transfer

Call Waiting

Conference

Call Park

Call Pickup

Anonymous Call

Anonymous Call Rejection
If you require additional information or assistance with your new phone, contact your
system administrator.
You can place a call in one of three ways using your SIP-T19(P) E2 IP phone:

Using the handset
67
User Guide for the SIP-T19(P) E2 IP Phone

Using the speakerphone

Using the headset
You can also dial the number first, and then choose the way you want to speak to the
other party.
You can also search and dial a contact from call history, local directory or remote phone
book. For more information, refer to Contact Management on page 31 and Call History
Management on page 47.
During a call, you can alternate between Speakerphone, Headset and Handset modes
by pressing the Speakerphone key, the Headset key, or by picking up the handset.
The call duration of the active call and far-site’s information (name or phone number)
are visible on the LCD screen. In the figure below, the call to ―Tom‖ (the phone number:
1002) has lasted 34 seconds.
To place a call using the handset:
1.
Pick up the handset.
2.
Enter the desired number using the keypad.
3.
Press
,
, or the Send soft key.
The # key is configured as a send key by default. You can also set the * key as the send
key, or set neither. For more information, refer to Key as Send on page 25.
Note
You can also dial using the SIP URI or IP address. To obtain the IP address of a phone,
press the
key when the phone is idle. The maximum SIP URI or IP address length is
32 characters. For example, SIP URI: 2210@sip.com, IP: 192.168.1.15.
Your phone may not support direct IP dialing. Contact your system administrator for more
information.
To place a call using the hands-free speakerphone mode:
Do one of the following:
-
With the handset on-hook, press
to obtain a dial tone.
Enter the desired number using the keypad.
Press
-
, or the Send soft key.
With the handset on-hook, enter the desired number using the keypad.
Press
68
,
,
,
, or the Send soft key.
Basic Call Features
To place a call using the headset:
1.
With the optional headset connected, press
2.
Enter the desired number using the keypad.
3.
Press
Note
,
to activate the headset mode.
, or the Send soft key.
To permanently use the headset mode, refer to Headset Prior on page 50.
The SIP-T19(P) E2 IP phone can handle multiple calls at a time. However, only one active
call (the call that has audio associated with it) can be in progress at any time, other
calls are placed on hold. The SIP-T19(P) E2 IP phone can handle a maximum of 2 calls at
one time.
To place multiple calls:
You can have more than one call on your SIP-T19(P) E2 IP phone. To place a new call
during an active call:
1.
Press the Hold soft key to place the original call on hold.
2.
Press the NewCall soft key.
3.
Enter the desired number using the keypad.
4.
Press
You can press
,
, or the Send soft key.
or
to switch between the calls, and then press the Resume soft
key to retrieve the desired call.
When you are not in another call, you can answer a call in one of three ways:
Note

Using the handset

Using the speakerphone

Using the headset
You can reject incoming calls by pressing the Reject soft key. You can also activate Do
Not Disturb mode to ignore all incoming calls without ring on your phone. For more
information, refer to Do Not Disturb (DND) on page 77.
You can forward incoming calls to someone else by pressing the FWD soft key. For more
information, refer to Call Forward on page 78.
Answering When Not in Another Call
Call duration and destination will always appear on the LCD screen for the active call.
69
User Guide for the SIP-T19(P) E2 IP Phone
To answer a call using the handset:
1.
Pick up the handset.
To answer a call using the hands-free speakerphone mode:
Do one of the following:
-
Press
.
-
With the handset on-hook and the headset mode deactivated, press the Answer
soft key.
To answer a call using the headset:
Do one of the following:
-
Press
.
-
With the headset mode activated, press the Answer soft key.
Answering When in Another Call
If you have an active call, and an incoming call arrives on the phone, do one of the
following:
-
Press the Answer soft key.
The incoming call is answered and the original call is placed on hold.
-
Press
to access the new call.
Press
or the Answer soft key.
The incoming call is answered and the original call is placed on hold.
To end a call:
Do one of the following:
-
If you are using the handset, press the EndCall soft key or hang up the handset.
-
If you are using the headset, press the EndCall soft key.
-
If you are using the speakerphone, press
To redial the last dialed number from your phone:
1.
Press
twice.
A call to your last dialed number is attempted.
70
or the EndCall soft key.
Basic Call Features
To redial a previously dialed number from your phone:
1.
Press
2.
Press
press
when the phone is idle.
or
to select the desired entry from the placed calls list, and then
or the Send soft key.
To view the placed calls list when the phone is on the dialing screen, you should enable
recent call in dialing in advance.
To enable recent call in dialing via web user interface:
Note
1.
Click on Directory->Setting.
2.
Select Enabled from the pull-down list of Recent Call In Dialing.
3.
Click Confirm to accept the change.
Recent call in dialing is configurable via web user interface only.
71
User Guide for the SIP-T19(P) E2 IP Phone
To view placed calls list when the phone is on the dialing screen:
1.
Pick up the handset or press the Speakerphone key.
The LCD screen displays the placed calls list.
You can also enter a few continuous characters of the contact name or continuous
numbers of the contact number (office, mobile or other number) to search from
placed calls list.
You can use auto answer feature to automatically answer an incoming call.
To configure auto answer via phone user interface:
1.
Press Menu->Features->Auto Answer.
2.
Press
to select the Status, and the press
select Enabled from the Status field.
72
or
, or the Switch soft key to
Basic Call Features
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
The
icon appears on the LCD screen.
Auto answer is configurable via web user interface at the path Account->Basic.
Note
Auto answer is only applicable when there is no other call in progress on the phone.
You can enable auto redial to automatically redial a phone number when the called
party is busy. You can also configure the number of auto redial attempts and the time to
wait between redial attempts.
To configure auto redial via phone user interface:
1.
Press Menu->Features->Auto Redial.
2.
Press
or
, or the Switch soft key to select Enabled from the Auto Redial
field.
3.
Enter the desired time (in seconds) in the Redial Interval field.
The default value is ―10‖.
4.
Enter the desired number of redial attempts in the Redial Times field.
The default value is ―10‖.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
Auto redial is configurable via web user interface at the path Features->General
Information.
73
User Guide for the SIP-T19(P) E2 IP Phone
To use auto redial:
When the called party is busy, the following prompt will appear on the LCD screen of the
phone:
1.
Press the OK soft key to activate auto redial. The following prompt will appear on
the LCD screen of the phone:
2.
Wait for the designated period of time or press the OK soft key to redial the phone
number.
The phone will retry as many times as configured until the called party is idle.
You can use call completion to notify the caller who failed to reach a desired party when
the party becomes available to receive a call.
To configure call completion via phone user interface:
1.
Press Menu->Features->Call Completion.
2.
Press
or
, or the Switch soft key to select Enabled from the Call Completion
field.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
Call completion is configurable via web user interface at the path Features->General
Information.
74
Basic Call Features
To use call completion:
When the called party is busy, the following prompt will appear on the LCD screen of the
phone:
1.
Press the OK soft key, the phone returns to the idle screen and call completion is
activated.
When the called party becomes idle, the following prompt will appear on the LCD
screen of the phone:
1.
Note
Press the OK soft key to redial the number.
Call completion is not available on all servers. For more information, contact your system
administrator.
You can press a recall key to place a call back to the last incoming call.
To configure a recall key via web user interface:
1.
Click on DSSKey->Programable Key.
2.
Select the desired programable key.
75
User Guide for the SIP-T19(P) E2 IP Phone
Note
3.
Select ReCall from the pull-down list of Type.
4.
Click Confirm to accept the change.
A recall key is configurable via web user interface only.
You can mute the microphone of the active audio device during an active call so that
the other party cannot hear you. Call mute applies to all modes (Handset, Headset and
Speakerphone).
To mute a call:
1.
Press
during an active call.
The LCD screen indicates that the call is now muted.
To un-mute a call:
1.
Press
again to un-mute the call.
You can place an active call on hold. Only one active call can be in progress at any time.
Other calls can be made and received while placing the original call on hold. When you
76
Basic Call Features
place a call on hold, your IP PBX may play music to the other party while waiting.
To place a call on hold:
1.
Press the Hold soft key during a call.
The LCD screen indicates that the call is on hold.
Note
The phone will beep softly every 30 seconds to remind you that you still have a call on
hold.
To resume a held call:
1.
Press the Resume soft key.
Multiple Calls on Hold:
If multiple calls are placed on hold:
1.
Press
or
to switch between the calls, and then press the Resume soft key
to retrieve the desired call.
If more than one call is placed on hold, a numbered prompt appears on the LCD screen,
for example ―1/2‖, indicating that this is the first call out of two calls.
You can use DND to reject incoming calls automatically on the phone. The prompt
message "n New Missed Call(s)" ("n" indicates the number of missed calls) will appear
on the LCD screen, and callers will receive a busy message. All calls you receive while
DND is enabled are logged to your missed calls list.
Note
The prompt message will display only if Missed Call Log is enabled. Missed call log is
configurable via web user interface at the path Account->Basic->Miss Call Log.
Do not disturb is local to the phone, and may be overridden by the server settings. For
more information, contact your system administrator.
To activate DND via phone user interface:
1.
Press the DND soft key when the phone is idle.
The
icon on the status bar indicates that DND is enabled.
77
User Guide for the SIP-T19(P) E2 IP Phone
Incoming calls will be rejected automatically and "n New Missed Call(s)" ("n"
indicates the number of missed calls. e.g., 1 New Missed Call(s)) will appear on the
LCD screen.
Note
When DND and busy forward are enabled at the same time, calls will be sent to the
configured destination number. For more information on busy forward, refer to Call
Forward on page 79.
DND is configurable via web user interface at the path Features->Forward & DND.
To configure the DND authorized numbers via web user interface:
1.
Click on Features->Forward & DND.
2.
Select Enabled from the pull-down list of DND Emergency.
3.
Enter the numbers in the DND Authorized Numbers field.
For multiple numbers, enter a comma between every two numbers.
4.
Click Confirm to accept the change.
When DND is enabled on the phone, the phone can still receive incoming calls from the
numbers specified in the DND Authorized Numbers field.
Note
78
DND authorized number is configurable via web user interface only.
Basic Call Features
You can configure your phone to forward incoming calls to another party through static
forwarding. You can also forward calls while your phone is ringing, refer to Dynamic
Forwarding.
Static Forwarding
Three types of static forwarding:

Always Forward: Incoming calls are immediately forwarded.

Busy Forward: Incoming calls are immediately forwarded if the phone is busy.

No Answer Forward: Incoming calls are forwarded if not answered after a period
of time.
To enable call forward via phone user interface:
1.
Press Menu->Features->Call Forward.
2.
Press
or
to select the desired forwarding type, and then press the Enter
soft key.
3.
Depending on your selection:
a)
If you select Always Forward:
1)
Press
or
, or the Switch soft key to select Enabled from the
Always Forward field.
2)
Enter the destination number you want to forward all incoming calls to in
the Forward to field.
3)
(Optional.) Enter the always forward on code or off code respectively in
the On Code or Off Code field.
b)
If you select Busy Forward:
1)
Press
or
, or the Switch soft key to select Enabled from the Busy
Forward field.
79
User Guide for the SIP-T19(P) E2 IP Phone
2)
Enter the destination number you want to forward incoming calls to when
the phone is busy in the Forward to field.
3)
(Optional.) Enter the busy forward on code or off code respectively in the
On Code or Off Code field.
c)
If you select No Answer Forward:
1)
Press
or
, or the Switch soft key to select Enabled from the No
Answer Forward field.
2)
Enter the destination number you want to forward unanswered incoming
calls to in the Forward to field.
3)
Press
or
, or the Switch soft key to select the ring time to wait
before forwarding from the After Ring Time field.
The default ring time is 12 seconds.
4)
(Optional.) Enter the no answer forward on code or off code respectively
in the On Code or Off Code field.
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
The
icon on the status bar indicates that the call forward is enabled.
Call forward is configurable via web user interface at the path Features->Forward &
DND.
Note
You can also enter the SIP URI or IP address in the Forward to field. For more information
on using the SIP URI or IP address, refer to Placing Calls on page 67.
Call forward is local to the phone, and may be overridden by the server settings. Call
forward on code or off code may be different between servers. For more information,
contact your system administrator.
To configure the forward authorized numbers via web user interface:
80
1.
Click on Features->Forward & DND.
2.
Select Enabled from the pull-down list of Forward Emergency.
3.
Enter the numbers in the Forward Authorized Numbers field.
Basic Call Features
For multiple numbers, enter a comma between every two numbers.
4.
Click Confirm to accept the change.
When call forward is enabled on the phone, the phone cannot forward incoming
calls from the numbers specified in the Forward Authorized Numbers field.
Note
Forward authorized number is configurable via web user interface only.
To disable call forward via phone user interface:
Do one of the following:
-
Press
-
Press Menu->Features->Call Forward.
Press
when the phone is idle.
or
to select the desired forwarding type and then press the Enter
or
, or the Switch soft key to select Disabled to disable the call
soft key.
Press
forward.
Press the Save soft key to accept the change.
Dynamic Forwarding
To forward an incoming call to another party:
1.
When the phone is ringing, press the FWD soft key.
81
User Guide for the SIP-T19(P) E2 IP Phone
2.
Enter the number you want to forward the incoming call to.
3.
Press
,
, or the Send soft key.
The LCD screen prompts a call forward message.
Note
When the phone forwards a call, a prompt window will pop up by default, if you want to
disable the feature, contact your system administrator for more information.
You can transfer a call to another party in one of three ways:

Blind Transfer: Transfer a call directly to another party without consulting.

Semi-Attended Transfer: Transfer a call when the target phone is ringing.

Attended Transfer: Transfer a call with prior consulting.
To perform a blind transfer:
1.
Press
or the Tran soft key during a call.
2.
Enter the number you want to transfer the call to.
3.
Press
or the Tran soft key to complete call transfer.
Then the call is connected to the number to which you are transferring.
To perform a semi-attended transfer:
1.
Press
or the Tran soft key during a call.
2.
Do one of the following:
-
Enter the number you want to transfer the call to.
-
Press the Dir soft key, and then select Local Directory. Select the desired group
and search for the contact (Directory should be configured in advance. Refer to
Directory on page 31 for more information).
-
Press the Dir soft key, and then select History. Select the desired list and then
press
or
to select the entry (Directory should be configured in
advance. Refer to Directory on page 31 for more information).
-
Press the Dir soft key, and then select Remote Phone Book. Select the desired
group and search for the contact (Directory should be configured in advance.
82
Basic Call Features
Refer to Directory on page 31 and Remote Phone Book on page 44 for more
information).
3.
Press
4.
Press
or
to dial out.
or the Tran soft key to complete the transfer when receiving ringback.
To perform an attended transfer:
1.
Press
or the Tran soft key during a call.
2.
Do one of the following:
-
Enter the number you want to transfer the call to.
-
Press the Dir soft key, and then select Local Directory. Select the desired group
and search for the contact (Directory should be configured in advance. Refer to
Directory on page 31 for more information).
-
Press the Dir soft key, and then select History. Select the desired list and then
press
or
to select the entry (Directory should be configured in
advance. Refer to Directory on page 31 for more information).
-
Press the Dir soft key, and then select Remote Phone Book. Select the desired
group and search for the contact (Directory should be configured in advance.
Refer to Directory on page 31 and Remote Phone Book on page 44 for more
information).
3.
Press
or
to dial out.
4.
After the party answers the call, press
or the Tran soft key to complete the
transfer.
If you are using a handset, the transfer can be completed by hanging up the handset.
You can cancel the transfer before the call is connected by pressing the Cancel soft key.
You can enable or disable call waiting on the phone. If call waiting is enabled, you can
receive another call while there is already an active call on the phone. Otherwise,
another incoming call is automatically rejected by the phone with a busy message
when there is an active call on the phone. You can also enable or disable the phone to
play a warning tone when receiving another call.
83
User Guide for the SIP-T19(P) E2 IP Phone
To configure call waiting via phone user interface:
1.
Press Menu->Features->Call Waiting.
2.
Press
or
, or the Switch soft key to select Enabled from the Call Waiting
or
, or the Switch soft key to select Enabled from the Play Tone field.
field.
3.
Press
4.
(Optional.) Enter the call waiting on code or off code respectively in the On Code
or Off Code field.
5.
Press the Save soft key to accept the change or the Back soft key to cancel.
Call waiting is configurable via web user interface at the path Features->General
Information.
You can create a conference with other two parties using the phone’s local conference.
You can create a conference between an active call and a call on hold by pressing the
Conf soft key. The SIP-T19(P) E2 IP phone also supports network conference.
Note
Network conference is not available on all servers. For more information, contact your
system administrator.
The SIP-T19(P) E2 IP phone supports up to 3 parties (including yourself) in a conference
call. This is the default method of conference called Local Conference.
To set up a local conference call:
1.
Place a call to the first party.
2.
When the first party answers the call, press the NewCall soft key to place a new
call.
The active call is placed on hold.
3.
Enter the number of the second party and then press
key.
84
,
, or the Send soft
Basic Call Features
4.
When the second party answers the call, press the Conf soft key again to join all
parties in the conference.
You can press
or
to see all parties in the conference.
During the conference call, you can do the following actions:
-
Press the Hold soft key to place the conference on hold.
-
Press the Split soft key to split the conference call into two individual calls on hold.
-
Press the Manage soft key, and then press

or
to select the desired party:
Press the FarMute soft key to mute the party. The muted party can hear
everyone, but no one can hear the muted party.
-

Press the Remove soft key to remove the party from the conference call.

Press the New Call soft key to place a new call.

Press the Back soft key to return to the previous screen.
Press
to mute the conference call, all other participants can hear each other,
but they cannot hear you.
-
Press the EndCall soft key to drop the conference call.
You can use network conference feature on the SIP-T19(P) E2 IP phone to conduct a
conference with multiple participants.
This feature allows you to perform the following:

Join two calls together into a conference call.

Invite another party into an active conference call.
To use this feature, contact your system administrator for the network conference URI in
advance.
To configure network conference via web user interface:
1.
Click on Account->Advanced.
2.
Select Network Conference from the pull-down list of Conference Type.
85
User Guide for the SIP-T19(P) E2 IP Phone
3.
Enter the conference URI (e.g., conference@example.com) in the Conference URI
field.
4.
Click Confirm to accept the change.
To set up a network conference call:
1.
Place a call to the first party.
2.
Press the NewCall soft key to place a new call.
The active call is placed on hold.
3.
Enter the number of the second party and then press
,
, or the Send soft
key.
4.
When the second party answers the call, press the Conf soft key to add the second
party to the conference.
5.
Press the NewCall soft key to place a new call.
6.
The conference is placed on hold.
7.
Enter the number of the new party and then press
8.
When the new party answers the call, press the Conf soft key to add the new party
,
, or the Send soft key.
to the conference.
9.
Repeat steps 5 to 7 until you have added all intended parties.
The procedures to set up a network conference call on specific servers may be different
from introduced above. Contact your system administrator for more information.
You can use call park feature to place a call on hold, and then retrieve the call from
another phone in the system (for example, a phone in another office or conference
room). You can park an active call by pressing the Park soft key. If the call is parked
86
Basic Call Features
successfully, there is a voice prompt confirming that the call was parked. You can
retrieve the parked call by pressing the Retrieve soft key. If the parked call is not
retrieved within a period of time defined by the system, the phone performing call park
will receive a call back.
Note
Call park is not available on all servers. Contact your system administrator for more
information.
The IP phone supports call park feature under the following modes:
FAC mode (dial the call park code to park the call to local extension or a desired

extension)
Transfer mode (park the call to directional parking lot directly)

You may need to configure the call park code/call park number or park retrieve
code/park retrieval number before using call park feature.
Note
The call park code/call park number and park retrieve code/park retrieval number are
predefined on the system server. Contact your system administrator for more
information.
To configure call park feature in FAC mode via web user interface:
1.
Click on Features->Call Pickup.
2.
Select FAC from the pull-down list of Call Park Mode.
3.
Select Enabled from the pull-down list of Call Park.
If Enabled is selected, the Park soft key will display on the LCD screen during a call,
and the Retrieve soft key will display on the dialing screen.
4.
(Optional.) Enter the call park code in the Call Park Code field.
It is configured for the Park soft key.
5.
(Optional.) Enter the park retrieve code in the Park Retrieve Code field.
87
User Guide for the SIP-T19(P) E2 IP Phone
It is configured for the Retrieve soft key.
6.
Note
Click Confirm to accept the change.
If the Park or Retrieve soft key doesn’t appear on the LCD screen, please select
Disabled from the pull-down list of Custom Softkey via web user interface at path
Settings->Softkey Layout.
To park a call in FAC mode:
1.
During a call, press the Park soft key (You may need to press the More soft key to
see the Park soft key).
-
If the call park code is not configured, you need to enter the call park code.
Press
-
,
or the Park soft key.
If the call park code is configured, the phone will dial the configured call park
code shown as below:
2.
Do one of the following:
a)
88
If you want to park the call against the local extension.
Basic Call Features
1)
Press
.
If the call is parked successfully, you will hear a voice prompt confirming
that the call is parked.
b)
If you want to park the call against desired extension.
1)
Enter an extension where you want to park the call.
2)
Press
or
.
If the call is parked successfully, you will hear a voice prompt confirming
that the call is parked. The call is parked against the extension you
entered.
To retrieve a parked call in FAC mode:
1.
Do one of the following:
-
If the park retrieve code is not configured, dial the park retrieve code (e.g.,
*88).
-
If the park retrieve code is configured, press the Retrieve soft key on the
dialing screen.
The phone will dial the configured park retrieve code and the Retrieve screen
appears as below:
2.
Follow the voice prompt, do one of the following:
-
Press
on the phone where the call is parked.
-
Enter the desired extension follow by # (e.g., 4603#) on any phone.
To configure call park feature in transfer mode via web user interface:
1.
Click on Features->Call Pickup.
2.
Select Transfer from the pull-down list of Call Park Mode.
3.
Select Enabled from the pull-down list of Call Park.
If Enabled is selected, the Park soft key will display on the LCD screen during a call,
and the Retrieve soft key will display on the dialing screen.
4.
(Optional.) Enter the call park number in the Call Park Code field.
It is configured for the Park soft key.
89
User Guide for the SIP-T19(P) E2 IP Phone
5.
(Optional.) Enter the park retrieval number in the Park Retrieve Code field.
It is configured for the Retrieve soft key.
6.
Note
Click Confirm to accept the change.
If the Park or Retrieve soft key doesn’t appear on the LCD screen, please select
Disabled from the pull-down list of Custom Softkey via web user interface at path
Settings->Softkey Layout.
To park a call in Transfer mode:
1.
During a call, press the Park soft key (You may need to press the More soft key to
see the Park soft key).
-
If the call park number is not configured, you need to enter the call park
number (e.g., *01).
Press
,
or the Park soft key. The call will be transferred to the
directional parking lot where the call park number directed to.
-
If the call park number is configured, the call will be directly transferred to the
directional parking lot where the call park number directed to.
90
Basic Call Features
To retrieve a parked call in Transfer mode:
1.
Do one of the following:
-
If the park retrieval number is not configured, you need to enter the park
retrieval number (e.g., *11).
Press
-
,
or the Send soft key.
If the park retrieval number is configured, press the Retrieve soft key on the
dialing screen.
The phone will retrieve the parked call from the directional parking lot where the
park retrieval number directed to.
You can use call pickup to answer someone else’s incoming call on your phone. The
SIP-T19(P) E2 IP phone supports directed call pickup and group call pickup. Directed call
pickup is used for picking up a call that is ringing at a target phone number. Group call
pickup is used for picking up a call that is ringing at any phone number in a certain
group. The pickup group should be predefined, contact your system administrator for
more information.
You can pick up an incoming call by using the DPickup/GPickup soft key. To use call
pickup, you need to configure the call pickup code beforehand on a global or per-line
basis via web user interface.
Note
If there are many incoming calls at the same time, pressing the GPickup soft key on the
phone will pick up the call that rings first.
Directed Call Pickup
To enable directed call pickup and configure the directed call pickup code on a global
basis via web user interface:
1.
Click on Features->Call Pickup.
2.
Select Enabled from the pull-down list of Directed Call Pickup.
91
User Guide for the SIP-T19(P) E2 IP Phone
3.
Enter the directed call pickup code in the Directed Call Pickup Code field.
4.
Click Confirm to accept the change.
To configure the directed call pickup code on a per-line basis via web user interface:
1.
Click on Account->Advanced.
2.
Enter the directed call pickup code in the Directed Call Pickup Code field.
3.
Click Confirm to accept the change.
To pick up a call directly:
1.
Pick up the handset or press the Speakerphone key (You may need to press the
More soft key to see the DPickup soft key).
92
Basic Call Features
The DPickup soft key appears on the LCD screen.
2.
Press the DPickup soft key on your phone when the target phone receives an
incoming call.
3.
Enter the phone number which is receiving an incoming call.
4.
Press the DPickup soft key again.
The call is answered on your phone.
Group Call Pickup
To enable group call pickup and configure the group call pickup code on a global basis
via web user interface:
1.
Click on Features->Call Pickup.
2.
Select Enabled from the pull-down list of Group Call Pickup.
3.
Enter the group call pickup code in the Group Call Pickup Code field.
4.
Click Confirm to accept the change.
To configure the group call pickup code on a per-line basis via web user interface:
1.
Click on Account->Advanced.
93
User Guide for the SIP-T19(P) E2 IP Phone
2.
Enter the group call pickup code in the Group Call Pickup Code field.
3.
Click Confirm to accept the change.
To pick up a call in the group:
1.
Pick up the handset or press the Speakerphone key.
The GPickup soft key appears on the LCD screen.
2.
Press the GPickup soft key on your phone when a phone in the group receives an
incoming call.
The call is answered on your phone.
Note
The directed call pickup code and group call pickup code are predefined on the system
server. Contact your system administrator for more information.
The call pickup code configured on a per-line basis takes precedence over that
configured on a global basis.
You can use anonymous call to block your identify and phone number from appearing
to the called party when you call someone. For example, you want to call to consult
94
Basic Call Features
some services, but don’t want to be harassed. Anonymous call is configurable on a
per-line basis. You can also configure the phone to send anonymous call on/off code to
the server to activate/deactivate anonymous call on the server side.
Note
Anonymous call is not available on all servers. Contact your system administrator for the
anonymous call on code and off code.
To configure anonymous call via phone user interface:
1.
Press Menu->Features->Anonymous Call.
2.
Press
or
, or the Switch soft key to select Enabled from the Local
Anonymous field.
3.
(Optional.) Press
or
to select the desired value from the Send Anony
Code field.
The phone will send the configured on code or off code depending on your
selection when you enable or disable anonymous call feature on the phone.
4.
(Optional.) Enter the anonymous call on code in the On Code field.
5.
(Optional.) Enter the anonymous call off code in the Off Code field.
6.
Press the Save soft key to accept the change or the Back soft key to cancel.
Anonymous call is configurable via web user interface at the path Account->Basic.
To place an anonymous call:
1.
Using the specific line on the phone to place a call to phone B.
The LCD screen of phone B prompts an incoming call from anonymity.
You can use anonymous call rejection to reject incoming calls from anonymous callers.
Anonymous call rejection automatically rejects incoming calls from callers who
95
User Guide for the SIP-T19(P) E2 IP Phone
deliberately block their identities and numbers from being displayed. Anonymous call
rejection is configurable on a per-line basis. You can also configure the phone to send
anonymous call rejection on/off code to the server to activate/deactivate anonymous
call rejection on the server side.
To configure anonymous call rejection via phone user interface:
1.
Press Menu->Features->Anonymous Call.
2.
Press
or
to scroll to the Anonymous Rejection field.
3.
Press
or
, or the Switch soft key to select Enabled from the Anonymous
Rejection field.
4.
(Optional.) Press
or
, or the Switch soft key to select the desired value
from the Send Rejection Code field.
The phone will send the configured reject on code or reject off code depending on
your selection when you enable or disable anonymous call rejection feature on the
phone.
5.
(Optional.) Enter the anonymous call rejection on code in the Reject On Code field.
6.
(Optional.) Enter the anonymous call rejection off code in the Reject Off Code field.
7.
Press the Save soft key to accept the change or the Back soft key to cancel.
Anonymous call rejection is configurable via web user interface at the path
Account->Basic.
96
Advanced Phone Features
This chapter provides operating instructions for the advanced features of the SIP-T19(P)
E2 IP phone. Topics include:

Hot Desking

Intercom

Multicast Paging

Music on Hold

Shared Call Appearance (SCA)

Bridged Line Appearance (BLA)

Messages
If you require additional information or assistance with your new phone, contact your
system administrator.
Hot desking originates from the definition of being the temporary physical occupant of
a work station or surface by a particular employee. A primary motivation for hot
desking is cost reduction. This feature is regularly used in places where not all the
employees are in the office at the same time, or not in the office for very long, which
means that actual personal offices would be often vacant, consuming valuable space
and resources.
You can use hot desking on the SIP-T19(P) E2 IP phone to log out of the existing accounts
and then log into a new account. As a result, many users can share the phone resource
at different times. To use this feature, you need to configure a hot desking key in
advance.
Note
Hot desking is not available on all servers. Contact your system administrator for more
information.
To configure a hot desking key via web user interface:
1.
Click on DSSKey->Programable Key.
2.
Select the desired programable key.
97
User Guide for the SIP-T19(P) E2 IP Phone
3.
4.
Note
Select Hot Desking from the pull-down list of Type.
Click Confirm to accept the change.
A hot desking key is configurable via web user interface only.
To use hot desking:
1.
Press the hot desking key when the phone is idle.
The LCD screen prompts the following warning:
2.
Press the OK soft key, registration configurations of all accounts on the phone will
be cleared immediately.
The login wizard will be displayed as below:
98
3.
Enter the login information in each field.
4.
Press the Save soft key to login or the Cancel soft key to cancel.
Advanced Phone Features
Intercom is a useful feature in an office environment to quickly connect with the operator
or the secretary. The SIP-T19(P) E2 IP phone supports automatically to answer an
incoming intercom call by default. The phone automatically plays a warning tone when
it receives an incoming intercom call. In addition, you can enable the phone to mute the
microphone when it automatically answers an incoming intercom call. You can also
enable the phone to automatically answer an incoming intercom call while there is
already an active call on the phone. The active call is then placed on hold.
Intercom features you need to know:
Intercom Feature
Accept Intercom
Intercom Mute
Intercom Tone
Description
Enable or disable the IP phone to answer an
incoming intercom call.
Enable or disable the IP phone’s microphone for
intercom calls.
Enable or disable the IP phone to play a warning
tone when it receives an incoming intercom call.
Enable or disable the IP phone to automatically
Intercom Barge
answer an incoming intercom call while there is
already an active call on the phone.
Accept Intercom
You can enable or disable the phone to answer an incoming intercom call. If Accept
Intercom is enabled, the phone will automatically answer an incoming intercom call. If
Accept Intercom is disabled, the phone will reject incoming intercom calls and send a
busy message to the caller. Accept Intercom is enabled by default.
Note
Your administrator can set a period of delay time before the phone automatically
answers intercom calls. Contact your system administrator for more information.
Intercom Mute
You can mute or un-mute the phone’s microphone for intercom calls automatically. If
Intercom Mute is enabled, the microphone will be muted for intercom calls. If Intercom
Mute is disabled, the microphone will work for intercom calls. Intercom Mute is disabled
by default.
Intercom Tone
You can enable or disable the phone to play a warning tone when receiving an
intercom call. If Intercom Tone is enabled, the phone will play a warning tone before
answering the intercom call. If Intercom Tone is disabled, the phone will automatically
answer the intercom call without warning. Intercom Tone is enabled by default.
99
User Guide for the SIP-T19(P) E2 IP Phone
Intercom Barge
You can enable or disable the phone to automatically answer an incoming intercom call
while there is already an active call on the phone. If Intercom Barge is enabled, the
phone will automatically answer the intercom call and place the active call on hold. If
Intercom Barge is disabled, the phone will handle an incoming intercom call like a
waiting call. Intercom Barge is disabled by default.
To configure intercom features via phone user interface:
1.
Press Menu->Features->Intercom.
2.
Make the desired changes.
3.
Press the Save soft key to accept the change or the Back soft key to cancel.
These specific parameters are configurable via web user interface at the path
Features->Intercom.
You can use multicast paging to quickly and easily broadcast time sensitive
announcements to users who are listening to a specific multicast group. You can
configure a paging list key on the phone, which allows you to send a Real Time
Transport Protocol (RTP) stream to the pre-configured multicast address(es) without
involving SIP signaling. You can configure the phone to receive an RTP stream from
pre-configured multicast listening address(es) without involving SIP signaling. You can
specify up to 10 multicast listening addresses.
To configure a paging list key via web user interface:
1.
2.
100
Click on DSSKey->Programable Key.
Select the desired programable key.
Advanced Phone Features
3.
Select Paging List from the pull-down list of Type.
4.
Click Confirm to accept the change.
To configure paging list via phone user interface:
1.
Press the paging list key when the phone is idle.
2.
Press
or
to select a desired paging group.
The default tag is Empty if it is not configured before.
3.
Press the Option soft key and then press the Edit soft key.
4.
Enter the multicast IP address and port number (e.g., 224.5.6.20:10008) in the
Address field.
The valid multicast IP addresses range from 224.0.0.0 to 239.255.255.255.
5.
Enter the group name in the Label field.
6.
Press the Save soft key to accept the change.
7.
Repeat steps 2 to 6, you can add more paging groups.
Paging list is configurable via web user interface at the path: Directory->Multicast IP.
101
User Guide for the SIP-T19(P) E2 IP Phone
To delete a paging group via phone user interface:
1.
Press the paging list key when the phone is idle.
2.
Press
3.
Press the Option soft key and then press the Delete soft key.
or
to select a desired group.
The LCD screen prompts ―Delete selected paging group?‖.
4.
Press the OK soft key to accept the change or the Cancel soft key to cancel.
If you want to delete all paging groups, you can press the Del All soft key.
You can configure the phone to receive a Real Time Transport Protocol (RTP) stream from
the pre-configured multicast address(es) without involving SIP signaling. You can
specify up to 10 multicast addresses that the phone listens to on the network.
How the phone handles incoming multicast paging calls depends on Paging Barge and
Paging Priority Active parameters configured via web user interface.
Paging Barge
The paging barge parameter defines the priority of the voice call in progress. If the
priority of an incoming multicast paging call is lower than that of the active call, it will be
ignored automatically. If Disabled is selected from the pull-down list of Paging Barge,
the voice call in progress will take precedence over all incoming multicast paging calls.
Valid values in the Paging Barge field:

1 to 10: Define the priority of the active call, 1 with the highest priority, 10 with the
lowest.

Disabled: The voice call in progress will take precedence over all incoming paging
calls.
Paging Priority Active
The paging priority active parameter decides how the phone handles incoming
multicast paging calls when there is already a multicast paging call on the phone. If
enabled, the phone will ignore incoming multicast paging calls with lower priorities,
otherwise, the phone will answer incoming multicast paging calls automatically and
place the previous multicast paging call on hold. If disabled, the phone will
automatically ignore all incoming multicast paging calls.
102
Advanced Phone Features
To configure multicast listening addresses via web user interface:
1.
Click on Directory->Multicast IP.
2.
Select the desired value from the pull-down list of Paging Barge.
3.
Select the desired value from the pull-down list of Paging Priority Active.
4.
Enter the multicast IP address(es) and port number (e.g., 224.5.6.20:10008) which
the phone listens to for incoming RTP multicast in the Listening Address field.
5.
Enter the label in the Label field.
Label will appear on the LCD screen when receiving the multicast RTP stream.
6.
Note
Click Confirm to accept the change.
The priorities of listening addresses are predefined: 1 with the highest priority, 10 with the
lowest.
Multicast listening addresses are configurable via web user interface only.
To send RTP stream via a paging list key when the receiver’s phone is idle:
1.
Press the paging list key when the phone is idle.
2.
Press
or
3.
Press
or the Paging soft key to send RTP.
to select the desired paging group.
The phone sends RTP to a preconfigured multicast address (IP: Port).
Both the sender’s and receiver’s phones play a warning tone and the receiver
automatically answers the multicast RTP session in the speakerphone mode.
103
User Guide for the SIP-T19(P) E2 IP Phone
The following figure shows a multicast RTP session on the phone:
4.
To place the current multicast RTP session on hold, press the Hold soft key.
The sender’s phone places the multicast RTP session on hold and receiver’s phone
releases the session.
5.
To resume the held multicast RTP session, press the Resume soft key.
The multicast RTP session is established again.
6.
Note
To end the multicast RTP session, press the EndCall soft key.
Multicast RTP is one way only from the sender to the multicast address(es) (receiver). For
outgoing RTP multicasts, all other existing calls on the phone will be placed on hold.
Music on hold (MoH) is the business practice of playing recorded music to fill the silence
that would be heard by the party placed on hold. To use this feature, you should specify
a SIP URI pointing to a Music on Hold Server account. When a call is placed on hold, the
phone will send a SIP INVITE message to the Music on Hold Server account. The Music
on Hold Server account automatically answers the SIP INVITE messages and
immediately plays audio from some source located anywhere (LAN, Internet) to the
held party. Contact your system administrator for the SIP URI.
To configure music on hold server via web user interface:
1.
104
Click on Account->Advanced.
Advanced Phone Features
2.
Enter the SIP URI (e.g., sip:moh@sip.com) in the Music Server URI field.
3.
Click Confirm to accept the change.
When you have placed a call on hold, the held party can hear the music.
Note
For this feature to function, all involved parties cannot use encrypted RTP (SRTP).
Music on hold server is configurable via web user interface only.
You can use SCA feature to share an extension which can be registered on two or more
IP phones at the same time. The shared line is indicated by a different line icon.
In the following figure, the registered line is shared:
If two phones share a line, an incoming call to this extension will cause both phones to
ring simultaneously. The incoming call can be answered on either phone but not both.
This feature is very useful in the boss and secretary scenario. For example, the secretary
can share the boss's extension on her phone. When there is an incoming call to the
extension of the boss, both the phones of the boss and the secretary will ring
simultaneously. Either the boss or the secretary can answer the call.
105
User Guide for the SIP-T19(P) E2 IP Phone
You can configure a primary account on the IP phone and other alternate accounts on
the other IP phones. For example, party A, party B share the account 4603, phone A
registers the primary account 4603, phone B registers the alternate account 4603_1,
phone C registers the account 4604.
To configure the shared line settings on phone A via web user interface:
1.
106
Register the account 4603.
Advanced Phone Features
2.
Click on Advanced, and then select Shared Call Appearance from the pull-down
list of Shared Line.
3.
Click Confirm to accept the change.
To configure the shared line settings on phone B via web user interface:
1.
Register the alternate account 4603_1.
(Enter the primary account 4603 in the Register Name field.)
107
User Guide for the SIP-T19(P) E2 IP Phone
2.
Click on Advanced, and then select Shared Call Appearance from the pull-down
list of Shared Line.
3.
Click Confirm to accept the change.
Configuring call pull feature
Call pull feature allows users to retrieve an existing call from another shared phone that
is in active or public hold status.
To configure the call pull feature access code via web user interface:
1.
108
Click on Account->Advanced.
Advanced Phone Features
2.
Enter the call pull feature access code (e.g., *11) in the Call Pull Feature Access
Code field.
3.
Click Confirm to accept the change.
The phone will dial out ―*11‖ automatically when you press the CallPull soft key.
This section provides you with detailed information on using the SIP-T19(P) E2 IP phone in
a SCA scenario.
You can do the following using SIP-T19(P) E2 IP phone in a SCA scenario:

Placing calls

Answering calls

Place a call on hold

Retrieving a held call

Call Pull
You can have one call or multiple calls on the shared line.
To place a call on the shared line:
1.
Enter the desired number using the keypad when the phone is idle.
2.
Press
,
, or the Send soft key.
109
User Guide for the SIP-T19(P) E2 IP Phone
To place multiple calls on the shared line:
You can have more than one call on the shared line. To place a new call when there is
an active call on phone A, do one of the following on phone A:
1.
Press the Hold soft key. The original call is placed on hold.
2.
Press the NewCall soft key to enter the dialing screen.
3.
Enter the desired number using the keypad.
4.
Press
,
, or the Send soft key.
Phone A will dial the entered number.
You can have one call or multiple calls on the shared line. Incoming calls will be
distributed evenly among the available shared line.
To answer a call on the shared line:
When an incoming call arrives on the shared line, the phone A and phone B will ring
simultaneously. You can answer the incoming call on either phone A or phone B but not
both.
Do one of the following on phone A or phone B:
-
Press
,
or the Answer soft key on phone A.
Phone B stops ringing.
-
Press
,
or the Answer soft key on phone B.
Phone A stops ringing.
To answer multiple calls on the shared line:
An incoming call arrives on the shared line when there is an active call on phone A. You
can answer the incoming call on either phone A or phone B. The LCD screen of phone A
displays the information of the incoming call (e.g., ‖Incoming call: 4604 Yealink‖).
Note
110
Make sure call waiting feature is enabled on phone A. For more information, refer to Call
Waiting on page 83.
Advanced Phone Features
Do one of the following on phone A:
-
Press the Answer soft key. Phone B stops ringing.
-
Press
to access the new call.
Press
or the Answer soft key. Phone B stops ringing.
The incoming call is answered and the original call is placed on hold.
You can also answer the call on phone B:
1.
Press
or the Answer soft key. Phone A stops ringing.
To place a call on hold:
1.
Press the Hold soft key on phone A when party A and party C are talking.
The shared line call is placed on hold.
If there is a held call between phone A and phone C, you can retrieve a held call on
phone A.
To retrieve the held call on phone A:
1.
Press the Resume soft key on phone A.
The conversation between phone A and phone C is retrieved.
Call pull feature allows users to retrieve an existing call from another shared phone that
is in active or hold status. For example, when there is a call between phone A and
phone C, you can use call pull feature on phone B to retrieve this call from phone A.
Then the call is established between phone B and phone C.
To retrieve a call from another shared phone:
If there is an active call between phone A and phone C, do the following:
1.
Enter the call pull feature access code (e.g., *11), and then press the Send soft key
on the phone B.
The active call has been retrieved from the phone A successfully.
111
User Guide for the SIP-T19(P) E2 IP Phone
If there is a held call between phone A and phone C, do the following:
1.
Enter the call pull feature access code (e.g., *11), and then press the Send soft key
on the phone B.
The held call has been retrieved from the phone A successfully.
BLA allows users to share a SIP line on two or more IP phones. Users can monitor the
specific extension (BLA number) for status changes on each IP phone. To use this feature,
a BLA group should be pre-configured on the server and one of them is specified as a
BLA number. BLA depends on support from a SIP server.
In the following figure, the registered account is shared:
Any IP phone can be used to originate or receive calls on the bridged line. An incoming
call to the BLA number can be presented to multiple phones in the group simultaneously.
The incoming call can be answered on any IP phone of the group but not all.
112
Advanced Phone Features
You can share a BLA number on two or more phones. For example, phone A registers
the account 14019833020 and assigns BLA number, phone B registers the account
10462190020 and assigns BLA number, phone C registers the account 14755608020.
Phone A and phone B share the BLA number 14084588327.
To register an account and configure BLA feature on phone A via web user interface:
1.
Register the account 14019833020.
113
User Guide for the SIP-T19(P) E2 IP Phone
2.
Click on Advanced, and then select Draft BLA from the pull-down list of Shared
Line.
114
3.
Enter the desired number in the BLA Number field.
4.
Click Confirm to accept the change.
Advanced Phone Features
To register an account and configure BLA feature on phone B via web user interface:
1.
Register the account 10462190020.
2.
Click on Advanced, and then select Draft BLA from the pull-down list of Shared
Line.
3.
Enter the desired number in the BLA Number field.
115
User Guide for the SIP-T19(P) E2 IP Phone
4.
Click Confirm to accept the change.
This section provides you with detailed information on using the SIP-T19(P) E2 IP phone in
a BLA scenario.
You can do the following using SIP-T19(P) E2 IP phone in a BLA scenario:

Placing calls

Answering calls

Place a call on hold

Retrieving a held call
You can have one call or multiple calls on the shared line.
To place a call on the shared line:
1.
Enter the desired number using the keypad when the phone is idle.
2.
Press
,
, or the Send soft key.
To place multiple calls on the shared line:
You can have more than one call on the shared line. To place a new call when there is
an active call on phone A, do one of the following on phone A:
1.
Press the Hold soft key. The original call is placed on hold.
2.
Press the NewCall soft key to enter the dialing screen.
3.
Enter the desired number using the keypad.
4.
Press
,
, or the Send soft key.
Phone A will dial the entered number.
When the phone C dials the BLA number ―14084588327‖, an incoming call will arrive on
the bridged line. The phone A and phone B ring simultaneously. You can answer the
incoming call on either phone A or phone B but not both.
Do one of the following on phone A or phone B:
-
Press
,
or the Answer soft key on phone A.
Phone B stops ringing.
-
Press
,
or the Answer soft key on phone B
Phone A stops ringing.
116
Advanced Phone Features
To place a call on hold:
1.
Press the Hold soft key on phone A when party A and party C are talking.
The bridged line call is placed on hold.
If there is a held call between phone A and phone C, you can retrieve a held call on
phone A.
To retrieve the held call on phone A:
1.
Press the Resume soft key on phone A.
The conversation between phone A and phone C is retrieved.
You can send and receive text messages using the SIP-T19(P) E2 IP phone. New text
messages can be indicated both acoustically and visually. When receiving a new text
message, the phone will play a warning tone. The power indicator LED will slow flash
yellow, and the LCD screen will prompt ―n New Text Message(s)‖ (―n‖ indicates the
number of unread text messages. e.g., 1 New Text Message(s)) and a flashing
icon
Note
.
When the phone receives a text message, the text message prompt window will pop up
by default, if you want to disable the feature, contact your system administrator for more
information.
You can store text messages in your phone’s Inbox, Sentbox, Outbox or Draftbox. Each
of the boxes can store up to 100 text messages. If the number of the text messages in
one box is more than 100, the phone will directly delete the oldest text message in the
box.
Note
SMS is not available on all servers. Contact your system administrator for more
information.
117
User Guide for the SIP-T19(P) E2 IP Phone
To read a text message:
Note
1.
Press Menu->Message->Text Message->Inbox.
2.
Select the desired message and then press the View soft key.
If the phone prompts receiving new text messages, you can also press the View soft key
to read the new messages directly.
To send a text message:
1.
Press Menu->Message->Text Message->New Message.
2.
Compose the new text message. You can press the abc soft key to change the
input mode.
3.
Press the Send soft key after completing the content.
4.
Enter the number you want to send the message to in the To field.
5.
Press the Send soft key to send the message or the Back soft key to cancel.
Sending a text message is configurable via web user interface at the path
Features->SMS.
To reply a text message:
118
1.
Press Menu->Message->Text Message->Inbox.
2.
Select the desired message and then press the Reply soft key.
Advanced Phone Features
3.
Compose the new text message. You can press the abc soft key to change the
input mode.
4.
Press the Send soft key after completing the content.
5.
Check the From and To fields, and then press the Send soft key.
To delete a text message:
1.
Press Menu->Message->Text Message->Inbox (Sentbox, Outbox or Draftbox).
2.
Select the desired message and then press the Delete soft key.
3.
Select Delete to delete the desired message, then press the OK soft key.
The LCD screen prompts ―Delete message?‖.
4.
Press the OK soft key to delete this message or the Cancel soft key to cancel.
You can also delete all text messages by pressing the Delete soft key and then select
Delete All. For more information, refer to the above steps.
Note
You can also delete a specific message after retrieving by pressing the Delete soft key.
You can leave voice mails for someone else using the SIP-T19(P) E2 IP phone. You can
also listen to voice mails that are stored in a voice mailbox. When receiving a new voice
mail, the phone will play a warning tone. The power indicator LED will slow flash yellow,
and the LCD screen will prompt ―n New Voice Mail(s)‖ (―n‖ indicates the number of
119
User Guide for the SIP-T19(P) E2 IP Phone
unread voice messages. e.g., 4 New Voice Mail(s)) and a flashing icon
.
If the voice mail pop-up message box disappears, it won't pop up again unless the user
receives a new voice mail or the user re-registers the account that has unread voice
mail(s).
Note
Voice Mail is not available on all servers.
You can configure the phone not to display the pop-up prompt, contact your system
administrator for more information.
To leave a voice mail:
You can leave a voice mail for someone else when he/she is busy or inconvenient to
answer the call. Follow the voice prompt from the system server to leave a voice mail,
and then hang up.
To configure voice mail access codes via phone user interface:
1.
Press Menu->Message->Voice Mail->Set Voice Mail.
2.
Press the navigation keys to highlight the account which you want to set.
3.
Press the 123 soft key to select the proper input mode and then enter the voice mail
access code (e.g., *97).
4.
Note
Press the Save soft key to accept the change or the Back soft key to cancel.
Voice mail access codes must be predefined on the system server. Contact your system
administrator for the more information.
To listen to voice mails:
1.
When the LCD screen prompts that the phone receives a new voice mail and the
power indicator LED slow flashes yellow, you can press
key to dial out the voice mail access code.
120
or the Connect soft
Advanced Phone Features
2.
Note
Follow the voice prompt to listen to your voice mails.
Before listening to voice mails, make sure the voice mail access code has been
configured.
When all new voice mails are retrieved, the power indicator LED will go out.
To view the voice mail via phone user interface:
1.
Press Menu->Message->Voice Mail->View Voice Mail.
2.
The LCD screen displays the amount of new and old voice mails.
3.
Press the Connect soft key to listen to voice mails.
The SIP-T19(P) E2 IP phone supports MWI when receiving a new voice message. If
someone leaves you a voice mail, you will receive a message waiting indicator. MWI
will be indicated in three ways: a warning tone, an indicator message (including a
voice mail icon) on the LCD screen, and the power indicator LED slow flashes yellow.
This will be cleared when you retrieve all voice mails or delete them.
The MWI service is unsolicited for some servers, so the SIP-T19(P) E2 IP phone only
handles the MWI messages sent from the server. But for other servers, the MWI service
is solicited, so the SIP-T19(P) E2 IP phone must enable subscription for MWI.
Note
MWI service is not available on all servers. Contact your system administrator for more
information.
The MWI subscription parameters you need to know:
Options
Subscribe for MWI
Description
Enable or disable a subscription for MWI service.
Period of MWI subscription. The IP phone sends a
MWI Subscription Period
refresh SUBSCRIBE request before initial SUBSCRIBE
expiration.
Subscribe MWI To Voice
Enable or disable a subscription to the voice mail
Mail
number for MWI service.
121
User Guide for the SIP-T19(P) E2 IP Phone
Options
Description
To use this feature, you should also configure the voice
mail number.
Note
The phone will send SUBSCRIBE messages for the MWI service to the account or the
voice number MWI service depending on the server. Contact your system administrator
for more information.
To configure subscribe for MWI via web user interface:
1.
Click on Account->Advanced.
2.
Select Enabled from the pull-down list of Subscribe for MWI field.
3.
Enter the period time in the MWI Subscription Period(Seconds) field.
4.
Click Confirm to accept the change.
The IP phone will subscribe to the account number for MWI service by default.
To enable subscribe MWI to voice mail via web user interface:
122
1.
Click on Account->Advanced.
2.
Select Enabled from the pull-down list of Subscribe for MWI.
3.
Select Enabled from the pull-down list of Subscribe MWI To Voice Mail.
Advanced Phone Features
4.
Enter the desired voice mail number in the Voice Mail field.
5.
Click Confirm to accept the change.
The IP phone will subscribe to the voice mail number for MWI service using
Subscribe MWI To Voice Mail.
Note
MWI subscription is configurable via web user interface only.
123
User Guide for the SIP-T19(P) E2 IP Phone
124
Troubleshooting
This chapter provides general troubleshooting information to help you solve the
problems you might encounter when using your SIP-T19(P) E2 IP phone.
If you require additional information or assistance with your new phone, contact your
system administrator.
How can I find the basic information of the IP phone?
Press
when the IP phone is idle to check the basic information of the IP phone, such
as IP address and firmware version. For more basic information, refer to Phone Status on
page 14.
How to obtain the MAC address of a phone when the phone is not powered on?
Three ways to obtain the MAC address of a phone:

You can ask your supplier for the shipping information sheet which includes MAC
addresses according to the corresponding PO (Purchase Order).

You can find the MAC address on the label of carton box.

You can also find the MAC address from the phone’s bar code on the back of the
phone.
What is the difference between user name, register name and display name?
Both user name and register name are defined by the server. A user name is used to
identify the account while a register name matched with a password is used for
authentication if required by the server. Display name is the caller ID that will be
displayed on the called party’s LCD screen. Server configuration may override the local
configuration.
Why is the LCD screen blank?

Ensure that the phone is properly plugged into a functional AC outlet.

Ensure that the phone is plugged into a socket controlled by a switch that is on.

If the phone is plugged into a power strip, try to plug it directly into a wall outlet
125
User Guide for the SIP-T19(P) E2 IP Phone
instead.

If your SIP-T19P E2 IP phone is powered from PoE, ensure you use a PoE-compliant
switch or hub.
Why does the phone display "Network unavailable"?

Ensure that the Ethernet cable is plugged into the Internet port on the phone and
the Ethernet cable is not loose.

Ensure that the switch or hub in your network is operational.

Contact your system administrator for more information.
Why doesn’t the phone display time and date correctly?
Check if you have configured the phone to obtain the time and date from the SNTP
server automatically. If the phone fails to connect to the SNTP server, contact your
system administrator for more information. You can also configure the time and date
manually. For more information, refer to Time & Date on page 23.
Why can’t I access web user interface using the default administrator user name and
password (admin/admin)?

It is case-sensitive, ensure the case is correct.

Ensure the password has not been changed.

If the password has been changed, but the computer remembers the old password,
try to clear the browser cache and try again or select another browser to login.
How to change the user password?
To change the user password via web user interface:
126
1.
Click on Security->Password.
2.
Select user from the pull-down list of User Type.
Troubleshooting
3.
Enter the new user password in the New Password field and Confirm Password
field.
4.
Click Confirm to accept the change.
You can also contact your system administrator for help.
Note
If you are logging into the web user interface of the phone with user credentials, you
need to enter the current user password in the Old Password field.
User password is configurable via web user interface only.
Why can’t I receive calls?

Check the SIP registration with your system administrator.

Check that the DND (Do Not Disturb) mode is deactivated on your phone. Refer to
Do Not Disturb (DND) on page 77.

Check that call forward is disabled on the phone. Refer to Call Forward on page 79.

Check whether the caller number is stored in the blacklist directory. Refer to Blacklist
on page 43.
Why does my handset not work?
Check that the handset cord is fully connected to both the handset jack on the phone
and handset. Refer to Phone Installation on page 11.
Why does my headset not work?

Check that the headset cord is properly connected to the headset jack on the
phone. Refer to Phone Installation on page 11.
127
User Guide for the SIP-T19(P) E2 IP Phone

Check that the headset mode is activated. Refer to Headset Use on page 50.

Check that the headset volume is adjusted to an appropriate level. Refer to Volume
on page 28.
Why can’t I get a dial tone?

Check for any loose connections and that the phone has been installed properly.
For the installation instructions, refer to Phone Installation on page 11.

Switch between the Handset, Headset (if present) or Hands-Free Speakerphone to
check whether the dial tone is present for one of the audio modes.
If the dial tone exists on another audio mode, connect a different handset or
headset to isolate the problem.
Why doesn’t the phone ring?
Check the ringer volume on the phone. To adjust the ringer volume setting, press the
Volume key when the phone is on-hook and idle. For more information, refer to Volume
on page 28.
Why does the phone play a tone when there is a call on hold? How to disable it?
When there is a call on hold, the phone will play a hold tone every 30 seconds. Call hold
tone is enabled by default. Call hold tone and the interval of playing a hold tone are
configurable via web user interface only.
To configure call hold tone and call hold tone delay via web user interface:
128
1.
Click on Features->General Information.
2.
Select the desired value from the pull-down list of Play Hold Tone.
Troubleshooting
3.
Enter the desired time in the Play Hold Tone Delay field.
4.
Click Confirm to accept the change.
How to make a call using SRTP?
You can enable SRTP to encrypt the audio stream(s) of phone calls. The parties
participating in the call should enable SRTP on a per-line basis.
To enable SRTP on a per-line basis via web user interface:
1.
Click on Account->Advanced.
129
User Guide for the SIP-T19(P) E2 IP Phone
2.
Select the desired value (Optional or Compulsory) from the pull-down list of RTP
Encryption(SRTP).
3.
Note
Click Confirm to accept the change.
SRTP is not available on all servers. Contact your system administrator for more
information.
SRTP is configurable via web user interface only.
How to export PCAP trace?
We may need you to provide a PCAP trace to help analyze your problem.
To export a PCAP trace via web user interface:
130
1.
Click on Settings->Configuration.
2.
Click Start to begin capturing signal traffic.
3.
Recreate the error to be documented in the trace.
4.
Click Stop to stop the capture.
Troubleshooting
5.
Click Export to open file download window, and then save the file to your local
system.
How to export system log?
We may need you to provide a system log to help analyze your problem.
To export the system log to a local PC via web user interface:
1.
Click on Settings->Configuration.
2.
Select 6 from the pull-down list of System Log Level.
The default system log level is ―3‖.
3.
Click Confirm to accept the change.
4.
Mark the Local radio box in the Export System Log field.
5.
Reproduce the issue.
131
User Guide for the SIP-T19(P) E2 IP Phone
6.
Click Export to open the file download window, and then save the file to your local
system.
You can also export the system log to a syslog server. Contact your system administrator
for more information.
Note
It is recommended to reset the syslog level to 3 after exporting the system syslog.
How to export all diagnostic files?
We may need you to provide three types of diagnostic files (including PCAP trace,
system log and BIN configuration file) to help analyze your problem. You can export
these files at a time.
To export all diagnostic files via web user interface:
1.
Click on Settings->Configuration.
2.
Click Start to begin capturing signal traffic.
The system log level will be automatically set to 6.
3.
Reproduce the issue.
4.
Click Stop to stop the capture.
The system log level will be reset to 3.
132
Troubleshooting
5.
Click Export to open file download window, and then save diagnostic files to your
local system.
Note
If the issue cannot be reproduced, just directly click Export to export all diagnostic
files.
How to reboot the phone?
To reboot the phone via web user interface:
Note
1.
Click on Settings->Upgrade.
2.
Click Reboot to reboot the IP phone.
Any reboot of the IP phone may take a few minutes.
133
User Guide for the SIP-T19(P) E2 IP Phone
How to upgrade firmware?
To upgrade firmware via web user interface:
1.
Click on Settings->Upgrade.
2.
Click Browse to locate the required firmware from your local system.
3.
Click Upgrade to upgrade the firmware.
The web user interface prompts ―Firmware of the SIP Phone will be updated. It will
take 5 minutes to complete. Please don't power off!‖.
4.
Click OK to confirm upgrading.
How to reset the phone?
Reset the phone to factory configurations after you have tried all troubleshooting
suggestions but do not solve the problem. You need to note that all customized settings
will be overwritten after reset.
To reset the phone via phone user interface:
1.
Press Menu->Settings->Advanced Settings (default password: admin)->Reset to
Factory.
2.
Press the Enter soft key.
The LCD screen prompts the following warning:
3.
134
Press the OK soft key.
Troubleshooting
The LCD screen prompts ―Resetting to factory,please wait…‖.
The LCD screen prompts ―Welcome Initializing…please wait‖.
The phone will be reset to factory settings sucessfully after startup.
Note
Reset of your phone may take a few minutes. Do not power off until the phone has started
up successfully.
135
User Guide for the SIP-T19(P) E2 IP Phone
136
Regulatory Notices
Contact your Yealink Authorized Reseller for information about service agreements
applicable to your product.
TO THE FULL EXTENT ALLOWED BY LAW, YEALINK EXCLUDES FOR ITSELF AND ITS
SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE
DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS,
LOSS OF INFORMATION OR DATA, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE,
FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN IF YEALINK OR ITS AUTHORIZED
RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH AMAGES, AND LIMITS ITS
LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE RICE PAID, AT
YEALINK’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE
AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.
Save these instructions. Read these safety instructions before use!
The following basic safety precautions should always be followed to reduce risk of fire,
electrical shock, and other personal injury.
General Requirements

Before you install and use the device, read the safety instructions carefully
and observe the situation during operation.

During the process of storage, transportation, and operation, please always
keep the device dry and clean.

During the process of storage, transportation, and operation, please avoid
collision and crash of the device.

Please attempt not to dismantle the device by yourself. In case of any
discrepancy, please contact the appointed maintenance center for repair.

Without prior written consent, no organization or individual is permitted to
make any change to the structure or the safety design of the device. Yealink
is under no circumstance liable to consequences or legal issues caused by
such changes.

Please refer to the relevant laws and statutes while using the device. Legal
rights of others should be respected as well.
Environmental Requirements

Place the device at a well-ventilated place. Do not expose the device under
direct sunlight.

Keep the device dry and free of dusts.

Place the device on a stable and level platform.
137
User Guide for the SIP-T19(P) E2 IP Phone

Please place no heavy objects on the device in case of damage and
deformation caused by the heavy load.

Keep at least 10 cm between the device and the closest object for heat
dissipation.

Do not place the device on or near any inflammable or fire-vulnerable object,
such as rubber-made materials.

Keep the device away from any heat source or bare fire, such as a candle or
an electric heater.

Keep the device away from any household appliance with strong magnetic
field or electromagnetic field, such as a microwave oven or a refrigerator.
Operating Requirements

Do not let a child operate the device without guidance.

Do not let a child play with the device or any accessory in case of accidental
swallowing.

Please use the accessories provided or authorized by the manufacturer only.

The power supply of the device shall meet the requirements of the input
voltage of the device. Please use the provided surge protection power
socket only.

Before plugging or unplugging any cable, make sure that your hands are
completely dry.

Do not spill liquid of any kind on the product or use the equipment near
water, for example, near a bathtub, washbowl, kitchen sink, wet basement
or near a swimming pool.

Do not tread on, pull, or over-bend any cable in case of malfunction of the
device.

During a thunderstorm, stop using the device and disconnect it from the
power supply. Unplug the power plug and the Asymmetric Digital Subscriber
Line (ADSL) twisted pair (the radio frequency cable) to avoid lightning strike.

If the device is left unused for a rather long time, disconnect it from the
power supply and unplug the power plug.

When there is smoke emitted from the device, or some abnormal noise or
smell, disconnect the device from the power supply, and unplug the power
plug immediately. Contact the specified maintenance center for repair.

Do not insert any object into equipment slots that is not part of the product or
auxiliary product.

Before connecting a cable, connect the grounding cable of the device first.
Do not disconnect the grounding cable until you disconnect all other cables.
Cleaning Requirements
138

Before cleaning the device, stop using it and disconnect it from the power
supply.

Use a piece of soft, dry and anti-static cloth to clean the device.

Keep the power plug clean and dry. Using a dirty or wet power plug may
lead to electric shock or other perils.
Appendix A-Time Zones
Time Zone
-11
-10
-9:30
-9
-8
-7
-6
-5
-4:30
-4
-3:30
-3
-2:30
-2
-1
0
+1
+2
+3
+3:30
+4
+4:30
+5
+5:30
+5:45
+6
+6:30
+7
+8
+8:45
+9
Time Zone Name
Samoa
United States-Hawaii-Aleutian, United States-Alaska-Aleutian
French Polynesia
United States-Alaska Time
Canada(Vancouver,Whitehorse), Mexico(Tijuana,Mexicali),
United States-Pacific Time
Canada(Edmonton,Calgary), Mexico(Mazatlan,Chihuahua),
United States-MST no DST, United States-Mountain Time
Canada-Manitoba(Winnipeg), Chile(Easter Islands),
Mexico(Mexico City,Acapulco), United States-Central Time
Bahamas(Nassau), Canada(Montreal,Ottawa,Quebec),
Cuba(Havana), United States-Eastern Time
Venezuela(Caracas)
Canada(Halifax,Saint John), Chile(Santiago),
Paraguay(Asuncion), United Kingdom-Bermuda(Bermuda),
United Kingdom(Falkland Islands), Trinidad&Tobago
Canada-New Foundland(St.Johns)
Argentina(Buenos Aires), Brazil(DST), Brazil(no DST),
Denmark-Greenland(Nuuk)
Newfoundland and Labrador
Brazil(no DST)
Portugal(Azores)
Denmark-Faroe Islands(Torshavn), GMT, Greenland,
Ireland(Dublin), Morocco, Portugal(Lisboa,Porto,Funchal),
Spain-Canary Islands(Las Palmas), United Kingdom(London)
Albania(Tirane), Austria(Vienna), Belgium(Brussels),
Caicos, Chad, Croatia(Zagreb), Czech Republic(Prague),
Denmark(Kopenhagen), France(Paris), Germany(Berlin),
Hungary(Budapest), Italy(Rome), Luxembourg(Luxembourg),
Macedonia(Skopje), Namibia(Windhoek),
Netherlands(Amsterdam), Spain(Madrid)
Estonia(Tallinn), Finland(Helsinki), Gaza Strip(Gaza),
Greece(Athens), Israel(Tel Aviv), Jordan(Amman), Latvia(Riga),
Lebanon(Beirut), Moldova(Kishinev), Romania(Bucharest),
Russia(Kaliningrad), Syria(Damascus), Turkey(Ankara),
Ukraine(Kyiv, Odessa)
East Africa Time, Iraq(Baghdad), Russia(Moscow)
Iran(Teheran)
Armenia(Yerevan), Azerbaijan(Baku), Georgia(Tbilisi),
Kazakhstan(Aktau), Russia(Samara)
Afghanistan(Kabul)
Kazakhstan(Aqtobe), Kyrgyzstan(Bishkek),
Pakistan(Islamabad), Russia(Chelyabinsk)
India(Calcutta)
Nepal(Katmandu)
Kazakhstan(Astana, Almaty), Russia(Novosibirsk,Omsk)
Myanmar(Naypyitaw)
Russia(Krasnoyarsk), Thailand(Bangkok)
Australia(Perth), China(Beijing), Russia(Irkutsk, Ulan-Ude),
Singapore(Singapore)
Eucla
Japan(Tokyo), Korea(Seoul), Russia(Yakutsk,Chita)
139
User Guide for the SIP-T19(P) E2 IP Phone
Time Zone
+9:30
+10
+10:30
+11
+11:30
+12
+12:45
+13
+13:30
+14
140
Time Zone Name
Australia(Adelaide), Australia(Darwin)
Australia(Brisbane), Australia(Hobart),
Australia(Sydney,Melboume,Canberra), Russia(Vladivostok)
Australia(Lord Howe Islands)
New Caledonia(Noumea), Russia(Srednekolymsk Time)
Norfolk Island
New Zealand(Wellington,Auckland), Russia(Kamchatka Time)
New Zealand(Chatham Islands)
Tonga(Nukualofa)
Chatham Islands
Kiribati
Index
D
A
About This Guide
v
Accessing the Remote Phone Book
Account Registration
57
Adding Contacts
35
Adding Groups
33
Administrator password
25
Advanced Phone Features
97
Anonymous Call
94
Anonymous Call Rejection
95
Answering Calls
69
Appendix A – Time Zones
139
Area Code 61
Attaching Stand
11
Audio Issues
128
Audio Settings 28
Auto Answer
72
Auto Redial
73
45
E
Editing Contacts
37
Editing Groups
34
Emergency Number 63
Ending Calls 70
Entering Data and Editing Fields
18
G
B
Basic Call Features
67
Basic Network Settings
15
Blacklist 43
Block Out 62
Bridged Line Appearance (BLA)
Declaration of Conformity
ii
Deleting Contacts
38
Deleting Groups 34
Dial-now
60
Dial Plan
58
Directory
31
Display Issues
125
Do Not Disturb (DND)
77
Documentations
7
Dual Headset
51
General Issues
125
General Settings
21
Getting Started
9
112
C
Call Completion
74
Call Forward
79
Call History Management
47
Call Hold/Resume
76
Call Issues
127
Call Mute
76
Call Park
86
Call Pickup 86
Call Transfer
82
Call Waiting
83
CE Mark Warning ii
Configuring an Access URL
45
Configuring BLA Feature on the IP Phone
113
Configuring SCA Feature on the IP Phone
106
Conference
84
Contact Management
31
Contrast
21
Copyright
ii
Customizing Your Phone
21
H
Hardware Component Instructions
1
Headset Mode Activation/Deactivation
Headset Prior
50
Headset Prior
50
Headset Use 50
Headset & Handset Issues
127
Hot Desking
97
Hotline
65
50
I
Icon Instructions
3
Idle Screen 18
Importing/Exporting Contact lists
In This Guide
v
Intercom
99
41
K
Key as Send
25
L
Language
22
LED Instructions
4
Limitation of Liability
137
141
User Guide for the SIP-T19(P) E2 IP Phone
Live Dialpad
64
Local Conference
84
Local Directory
33
Log Issues
130
Logo Customization
49
T
Table of Contents
vii
Time & Date 23
Troubleshooting
125
U
M
Messages
117
Message Waiting Indicator
Multicast Paging 100
Music on Hold
104
User Interfaces
4
Using BLA Features on the IP Phone
Using Multicast Paging
103
Using SCA Features on the IP Phone
121
V
N
Network Conference
Voice Mail
119
Volume
28
85
O
Overview 1
Optional Accessories
W
Warranty
ii
Web User Interface
WEEE Warning
iii
10
P
Packaging Contents
9
Password Issues
126
Phone Initialization
14
Phone Installation
11
Phone Status
14
Phone User Interface
5
Placing Calls
67
Placing Calls to Contacts
Programable Keys
52
Phone Lock
26
39
R
Reboot & Upgrade & Reset Issues
Recall
75
Receiving RTP Stream 102
Recent Call In Dialing 71
Redialing Numbers 70
Registration
17
Regulatory Notices 137
Remote Phone Book
44
Replace Rule
58
Ring Tones
29
133
S
Safety Instructions
137
Search Source List in Dialing
40
Searching for Contacts
40
Sending RTP Stream
100
Service Agreements
137
Shared Call Appearance (SCA)
105
Short Message Service (SMS)
117
Summary of Changes
v
System Customizations
49
142
5
116
109