SSD SUPPORT SOLUTIONS
bizhub 360 - ALL ACTIVE SOLUTIONS
October 2009
This document contains information that was exported directly from Konica Minolta's SSD
Support knowledge base. Some solutions may contain hyperlink references which originally
contained links to graphic or text files. If you wish to view these files, you must access the
solutions via SSD CS Expert Support on Konica Minolta's website, www.kmbs.konicaminolta.us.
Legal Notice
This document is designed as a diagnostic tool, primarily for Konica Minolta's support personnel, and authorized
service representatives. Konica Minolta recommends that all service be performed by an authorized service
representative. Users are responsible for seeking advice of a Konica Minolta authorized service representative
regarding the information, opinion, advice or content of this document.
USER AGREES THAT USE OF THIS DOCUMENT IS AT USER'S SOLE RISK AND THAT THIS DOCUMENT IS PROVIDED
ON AN AS IS BASIS WITHOUT WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, WARRANTIES OF TITLE OR IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, OTHER THAN THOSE WARRANTIES THAT ARE IMPLIED BY LAW AND INCAPABLE OF
EXCLUSION. IN NO EVENT WILL KONICA MINOLTA OR THOSE ACTING ON ITS BEHALF BE LIABLE FOR ANY
DAMAGES, INCLUDING, WITHOUT LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL, CONSEQUENTIAL OR
PUNITIVE DAMAGES ARISING OUT OF YOUR USE OF THIS DOCUMENT.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
bizhub 360
Solution ID
Abnormal noise or odor
TAUS0702956EN*
Solution Usage
2
Description
PC-102/PC-202/PC-402, abnormal noise when feeding paper from Tray 2.
Solution
CAUSE: Vibration of the Separation Roller fulcrum shaft when stopping its revolution when two or more sheets of paper are fed between Feed Roller and
Separation Roller.
SOLUTION: Install Spacers (p/n 4040 5610 00 and p/n 4040 5612 00) to prevent the noise. Please refer to the attached documentation for the spacer
location and install procedure. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by KMBT (Japan)
Solution ID
TAUS0902363EN*
Solution Usage
Description
Squeaking noise coming from the ADU (duplex) area.
Solution
CAUSE: The noise seems to be emanating from the area near the duplex drive gear (large white gear on the MFP drive section driving the duplex unit). It can
be seen from the right side when the ADU door is open.
SOLUTION: Remove each of the gears (4) from their shaft on the Caulking Assembly in the Drive Unit (see attached Parts Manual page as a reference).
Thoroughly clean the gears and each shaft then apply a light coating of grease like MOLYKOTE® EM-50L (p/n 4478 7801 01). Attached is the MOLYKOTE®
EM-50L MSDS and Product Information sheet.
SPECIAL NOTE : Solution contribution by Craig Blyther, ASG/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
2
bizhub 360
Solution ID
Breakage, damage, malformed, removed part
TAUS0801906EN*
Solution Usage
8
Description
Code C1183(C-1183).
Solution
CAUSE:Elevator position sensor failure.This failure may be due to a broken boss on the elevator unit due to a chemical reaction between plastic and oil in the
area (see the attached picture). The broken boss is under the metal plate attached by the screw shown in the picture.
SOLUTION: A free of charge elevator unit (p/n 4349070101) is availble to correct this problem. To claim the free elevator unit, please use the following
procedure:
1. Open an SSD ticket.
2. It is mandatory to provide the machine and FS-508 or FS-510serial numbers for this claim to be processed.
3. Take a picture of the broken boss and attach it to the ticket.
4. Follow the online FOC Part(s) Ordering Procedure:
FOC PART(s) ORDERING PROCEDURE
A Free-of-Charge (FOC) elevator unit (p/n 4349070101) can be ordered via the Online Technical (FOC) & Special Program order form in
MyKonicaMinolta.com.
To place the FOC claim, please go to Service => Warranty Repair & Special Programs => Warranty Services & Technical/FOC Programs
=> KMBS Technical (FOC) & Special Programs. Access and complete the SSD Program claim form that is located in the Claim Type drop-down by
selecting “SSD Solution Claim” (bottom of the list).
After selecting "SSD Solution Claim", select the appropriate Solution ID from the “SSD Solutions” pop-up box in the Product RA/Claim Information at the
bottom of the form. A description of the associated FOC part that will be shipped is then displayed.
Under this SSD program, KMBS will ship all parts at no-charge.
Upon receipt and verification of the online claim information, KMBS Service Operations will process a Free-of-Charge parts order.
All parts will be shipped via UPS 2-day Air Service, and an automated E-mail will be sent to the submitting KMBS Customer confirming the shipment and the
KMBS claim number, parts order status and the UPS tracking number for the delivery.
Questions related to the FOC parts claims may be directed to KMBS Logistics Operations at (201) 934-5339.
SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/SSD
Solution ID
TAUS0703359EN*
Solution Usage
6
Description
Paper size(s) and/or paper tray(s) not recognized or recognized with the incorrect paper size indicated.
Solution
CAUSE: Paper cassette (tray) is cracked. The affected options are:
PC-101
PC-102
PC-103
PC-201
PC-202
PC-203
PF-124
PF-210
SOLUTION: Install the cassette repair countermeasure(s) as explained in the attached Parts Modification Notices and associated Applied Product
Information. Also, please refer to attached Bulletin Number 5606.
Note :To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Solution ID
TAUS0701603EN*
Solution Usage
1
Description
C-1190 (C1190)or C-1191 (C1191).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
3
bizhub 360
Breakage, damage, malformed, removed part
Solution
CAUSE: Possible crack in the motor mounting bushing located in the finisher.
SOLUTION: Obtain and install the Motor Mounting Repair Kit (p/n U700-0010) using the detailed procedures in attached Bulletin Number 5917.To view a
PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
4
bizhub 360
Solution ID
Controller - no or slow print, scan failure, garbled data, lockup
TAUS0647541EN*
Solution Usage
13
Description
C-B003 (CB003) code.
Solution
PROBABLE CAUSES:
1. The fax board is installed in the incorrect slot.
Install the fax board in the rearmost slot.
2. The Fax (Sub) was set to SET at installation.
Change the Fax (Sub) to Unset in Service Mode by performing the following:
a. Access the Service Mode.
b. Select the Option Board Status.
c. Select UNSET of Fax (Sub).
d. Select End and Exit to return to copy screen.
3.The FK-502 board is not seated properly.
Remove and reseat the fax board.
bizhub C451/C550/C650
4. Poor connection between the Fax board and the PCI board.
Ensure the connection between the Fax board and PCI board is secure.
Note : Please use the attached document on how to check the connection between the Fax board and PCI board.
5. The mounting brace for the PCI interface board into whichthe FK-502connectshas been pushed back, not making a complete connection.
Note : C-B016 code may also be indicated.
Reform the mounting brace for the PCI interface board and ensure that the FK-502 is properly seated intothe connection.If the problem persists initialize the
Fax board
(Service Mode =>Fax =>Initialization).
6. Fax misconfiguration. The fax option isenabled when there is no fax kit installed.
Disablethe fax option:
a. Enter the Service mode.
b. Select System 2.
c. Select option Board Status.
d. Check that Fax Circuit 1 and Circuit 2 are set to UNSET.
e. Touch End andback out of Service mode.
f. Power cycle the machine using the main power switch.
bizhub C552/C652
7. The fax PWB was installed in the incorrect slot.
When installing the fax PWB, it should be in the left slot when viewed from the right side of the copier. That slot is labeled "1" in the attached image. If the
dual line kit is to be installed, that PWB would be installed in the right slot. That slot is labeled "2" in the attached Fax Install photo.
bizhub C351/C450
8. PWB-PCI board (p/n 4037 0141 03) is damaged during installation. If the PWB-PCI board is inserted into the middle slot instead of the rear slot, or if the
board is mishandled, damage to the board may occur.
Notes :
a.Damage may be caused by scratching the board with Board Guide when installing PWB-PCI and Board Guide.
b. C-B001 may also be indicated and it is impossible to send/receive a fax.
Replace PWB-PCI (a part of MK-703 used for connection with optional board) taking care not to scratch or damage the board. Please refer to attached
documentation for details.
bizhub C250
9. Power supply (PU1) problem.
Replace the DC power supply(p/n 4038 6201 02).
SPECIAL NOTE : Solution contribution byDavid Hansen, KMBS/Seattle.
bizhub 600/750
10. The FK-502 was not deinstalled in Tech Rep mode SYSTEM 2 when removed.
Deinstall the FK-502 in Tech Rep mode by performing the following procedure:
a. Power OFF the machine with the main power switch.
b. Press and hold the Utility Key and power ON the machine. Hold the Utility key until the Konica Minolta logo appears and or Trouble reset.
c. Press Trouble Reset and enter Stop 0, 0 Stop, 0, 1. Press System 2 and then FAX.
d. Select Fax Not Installed.
bizhub 361/421/501
11. FK-502 firmware is below version 10.
Please install FK-502 version 10 firmware or above to prevent the intermittent display of a C-B003.The latest version firmware or system software is available
via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
5
bizhub 360
Controller - no or slow print, scan failure, garbled data, lockup
bizhub 360/420/500/361/421/501
12. Internal softwarefor the circuit board of ML-503 (FAX multi-line KIT) has been changed for bizhub 501/421/361. When using the previous ML-503 (before
the modification), the FK-502 might not recognize the ML-503.
Use the modified ML-503 whichcan be used for bizhub 501/421/361 and bizhub 500/420/360. The modified ML-503 has a yellow tag seal on the side of the
box as shown.
Please refer to attached documentation for ML-503 installation procedure.
13. The machine may display a C-B003 after the ML-503 is installed if the switch on the second fax kit has not been set to Line 2.
Please confirm SW2 on the second FK-502 is set to Line 2. Refer to the attached ML-503 InstallationManual providing the location of SW2 (page E-2).
bizhub 360/420/500
14. Problem withoptional HDD if the fax option is also installed.
To correct, please perform the following:
a.Enter the Service mode and set thefax unit to "Uninstalled."(Service mode => System 2 => Option => Fax#1)
b. Power down machine and unplug.Disconnect thefax unit.
c.Perform the HDD setup described on pages E-2 and E-3 of the HD-505 Installation Manual.
d. If the setup is unsuccessful, replace the HD-505 (Item #16GA).
e. PowerOFF the machine.
f. Install the Fax unit.
g. Power onthe machineand set the fax unit to "Installed." (Service mode => System 2 => Option => Fax#1)
h.If necessary,initialize the fax unit. (Service mode => Fax => Initialization => Fax Function Parameters)
Note : Please refer to attached HD-505 Installation Manual.To viewa PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free
from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution byRich Raynor, ASG/SSD; Mark D'Attilio/Cesar Jimenez/Gary Scimeca/Ian Lynch, Production Print/SSD and Dave
Bruni/Bill Hall/David Silverstein/John Miller, Workgroup/SSD
Solution ID
TAUS0701320EN*
Solution Usage
13
Description
Unable to print and the Print tab is missing from the Web interface. There is also no option for printer from the machine LCD.
Solution
CAUSE: The IC-204 (bizhub 360/420/500) or IC-207 (bizhub 361/421/501) print controller is not installed.
SOLUTION: Verify that the print controller is not installed on the OACB. Order and install the IC-204 (p/n 16JE) or IC-207 (p/n A0P80Y1) print controller.
Note : The IC-204 is a little 8-pin chip that mounts on the OACB above the memory slots. There is also a yellow sticker on the chip that indicates IC-204.
The IC-207 is a little 8-pin chip that mounts to the left of the memory slots near the top.
SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD
Solution ID
TAUS0807953EN*
Solution Usage
2
Description
PROBLEM:
Intermittently, the machine will lock up or not power ON.
Solution
CAUSE: Failed PRCB and/ or the OACB.
SOLUTION: Replace the PRCB (p/n 50GA-9020E) and OACB(p/n 50GA-930 1H) and Update the firmware to level 31.
Note: The PRCB will have a low level. It must flashed with Ganges image boot 20, then flashed to 31.
Note: The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS
Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
Solution by Don St.Onge -SSD Windsor.
Solution ID
TAUS0702947EN*
Solution Usage
1
Description
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
6
bizhub 360
Controller - no or slow print, scan failure, garbled data, lockup
When sending a fax from the FK-502 to a HP9120 fax machine or Olivetti® MFP machine, d-Color MF260, the line remains connected.
Solution
CAUSE: HP V.34 protocol or FK-502 settings/firmware.
SOLUTION: Prior to upgrading the firmware (if necessary), set V.34 = OFF when sending a fax to the HP9120 Fax or Olivetti® d-Color MF260:
1. Inserting the fax number directly on the fax display
If sending a FAX inserting directly the fax number on the fax display, set the “V.34” protocol OFF by performing the following setting:
FAX Button => Common Setting => Line Setting => “V.34 OFF”, and then press the OK button twice.
2. Storing the fax Number in the Address Book
When adding a new contact to the Address Book via the Web Interface, perform the following setting :
Enter the TCP/IP address of the machine within the browser => Scan => Address Book => New Redistration => Abbr. Dial => Next => Insert
User Name and Destination => Select “V.34 OFF” = ON => Apply.
If adding a new contact via product keyboard, perform the following steps:
Utility/Counter => One Touch Registration => FAX => Address Book => Address Dial => New => Insert User Name and FAX Number =>
Line Setting => Select “V.34 OFF” (this button must be highlighted in blue) => click twice the OK button.
Performing the above-mentioned setting when creating a new Contact causes the FK-502 to disable the “V.34” protocol for this Contact only.
When sending a fax to another Contact without to having set “V.34” OFF, the machine again uses the “V.34” protocol.
Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
SPECIAL NOTE : Solution contribution by KM Europe (BEU).
Solution ID
TAUS0800188EN*
Solution Usage
1
Description
PJL commands are being ignored from the AS/400® when printing to the bizhub 360.
Solution
CAUSE:The controller get "confused" when a PJL outbin command is used with a PCL outbin command. The result are that PJL commands are dropped.
SOLUTION:For ASCII,remove the PCL outbin command. This can be done with a search and replace string function within an externalprinter server.
For AS/400®, a WSCST can be created to not translate (ignore) the outbin command. This way the controller will not get "confused" and process the PJL
commands correctly.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD
Solution ID
TAUS0802636EN*
Solution Usage
1
Description
TheMFP can transmit a fax, but not receive a fax.
Solution
CAUSE: The "Number of rings" setting needs to be changed to 0.
SOLUTION: To change the "Number of rings" setting for the fax, perform the following procedure:
1. Enter Admin mode.
2. Select Fax Settings.
3. Select Telephone Line Settings.
4. Select Number Of Rx Call Rings and set it to 0.
5. Press Close 4x to exit the menu.
SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD
Solution ID
TAUS0701967EN*
Solution Usage
Description
When attempting to scan to SMB, the machine displays "Job Done Improperly" when user authentication is being used.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
7
bizhub 360
Controller - no or slow print, scan failure, garbled data, lockup
Solution
CAUSE: The scan cannot be completed due to an incorrect NTLM setting.
SOLUTION: Set the NTLM setting to V2 when authentication is being used. This will allow the scans to be completed.
To correct the settings perform the following:
1. Enter the administrator mode
2. Select network setting, then SMB setting.
3. Use the forward key and go to page 4/4.
4. Select V2 under the NTLM setting.
SPECIAL NOTE: Solution contribution by Mike Galletta, Workgroup/SSD
Solution ID
TAUS0800234EN*
Solution Usage
Description
While printing from mainframe using VPS, the printer hangs.
Solution
CAUSE:VPS is usually set up to dump all jobs in a single connection (session) andthis causes the bizhub to hang.
SOLUTION:In the VPS definition file on the mainframe use the following settings:
TCPOPTS=00000020
RELREQ=A
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD
Solution ID
TAUS0801997EN*
Solution Usage
Description
Output for AS/400® loops continuouslyuntil job is held.
Solution
CAUSE: When using a remote output queue on an AS/400®, the XAIX destination option is normally used for printing multiple copies.
The remote writer opens the connection to the printer and sends down multiple copies of the print data and control file pair. Each control file contains one
print command for the data file that preceded it. This method is required for printers that start printing the data right away. However, there are some print
servers that will close the connection after the first copy is sent. This is an unexpected close, resulting in retrying to send from the beginning which will cause
the remote writer to loop forever and will cause the spooled file to be printed indefinitely. In this case, XAIX should not be used.
When XAIX is not specified, the data file and control file will be sent once, but the control file will contain multiple print commands. This reduces network
traffic, but can only be used with serversthat can buffer all the data before knowing how many copies to print.
Therefore, without XAIX specified, the print server may or may not print multiple copies of the OS/400® or i5/OS® spooled file.
SOLUTION: Install the following minimum firmware version:
bizhub 350/250/200
Base firmware version 80 (filename: 4040-0100-G30-80-002)
bizhub 360/420/500
Special model-specific firmware version 31-GD1 file name:
bizhub 360: 360us_m0g3100d1.exe
bizhub 420: 420us_m0g3100d1.exe
bizhub 500: 500us_m0g3100d1.exe
bizhub 361/421/501
Special model-specific firmware version 13-GC5 file name:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
8
bizhub 360
Controller - no or slow print, scan failure, garbled data, lockup
bizhub 501: 501US_m1g1300c5.exe
bizhub 421: 421US_m1g1300c5.exe
bizhub 361: 361US_m1g1300c5.exe
bizhub C203/C253/C353/C353P
Special model-specific firmware version, file name and checksum:
bizhub C353 GC2-R4 : A02E0Y0-F000-GC2-R4.EXE, Checksum8FE5
bizhub C253 GD2-R4 : A02E0Y0-F000-GD2-R4.EXE, Checksum9C53
bizhub C203 GE2-R4 : A02E0Y0-F000-GE2-R4.EXE, ChecksumBF30
bizhub C353P GW1-72 : A02E0Y0-F000-GW1-72.EXE, Checksum9217
bizhub C451/C550/C650
Special model-specific firmware version GC2-R4, file name and checksum:
bizhub C451 GC2-R4: A00K0Y0 -F000-GC2-R4.EXE, Checksum 80AA
bizhub C550 GC2-R4: A00J0Y0 -F000-GC2-R4.EXE, Checksum 2266
bizhub C650 GC2-R4: A00H0Y0 -F000-GC2-R4.EXE, Checksum A684
bizhub PRO 1050 Series/IC-611
Print controller system code (ISW Trns install) version 31_CPF0_ISW (filename: 1050_p131cpf0p.exe)
Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS
Solution ID
TAUS0802343EN*
Solution Usage
Description
Unable to TX to a BH350 T00 T86 and T48 codes.
Solution
CAUSE: ECM is enabled and coding ability is set JBIG
SOLUTION: Disable ECM and to change protocol to MH only also
Uncheck option for "Check Remote Destination".
SPECIAL NOTE: Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0802637EN*
Solution Usage
Description
Host Name and File Path are blank using Scan-to-Home (Folder).
Solution
CAUSE: The LDAP server does not respond to an MFP request with the expected resultbecause the domain user’s E-mail address field is blank.
SOLUTION: The following table lists modification notices and special firmware for each engine series.
Model
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
9
bizhub 360
Controller - no or slow print, scan failure, garbled data, lockup
Modification Notice
Firmware
360
DLBT0803345EN00.PDF
360US_M0G3100VW.EXE
420
DLBT0803345EN00.PDF
420US_M0G3100VW.EXE
500
DLBT0803345EN00.PDF
500US_M0G3100VW.EXE
361
DLBT0803346EN00.PDF
361US_M1G1300UI.EXE
421
DLBT0803346EN00.PDF
421US_M1G1300UI.EXE
501
DLBT0803346EN00.PDF
501US_M1G1300UI.EXE
600
DLBT0803843EN00.PDF
600_750_US_M1G3000V9.EXE
750
DLBT0803843EN00.PDF
600_750_US_M1G3000V9.EXE
C203
DLBT0803485EN00.PDF
C203_A02E0Y0-F000-GE8-R5.EXE
C253
DLBT0803484EN00.PDF
C253_A02E0Y0-F000-GD8-R5.EXE
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
10
bizhub 360
Controller - no or slow print, scan failure, garbled data, lockup
C353
DLBT0803483EN00.PDF
C353_A02E0Y0-F000-GC8-R5.EXE
C451
DLBT0803493EN00.PDF
C451_A00K0Y0-F000-GC8-R5.EXE
C550
DLBT0803492EN00.PDF
C550_A00J0Y0-F000-GC8-R5.EXE
C650
DLBT0803491EN00.PDF
C650 A00H0Y0-F000-GC8-R5.EXE
The modification notice and firmwareare available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert
Support) by clicking on 'Download MSDS, Drivers, Firmware and more'
Note: To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
SPECIAL NOTE : Solution contribution by Rick Veale, ESS/BSE
Solution ID
TAUS0807881EN*
Solution Usage
Description
To transmit a fax, the Off-Hook button must be pressed. Otherwise, the fax does not transmit.
Solution
CAUSE: The dial tone detection is set to On in the fax.
SOLUTION: To turn off the dial tone detection, perform the following procedure:
1. Enter Tech Rep Mode.
2. Select Fax.
3. Select Network and then select the #2 setting.
4. Set the Dial Tone Detect to Off.
5. Exit Tech Rep Mode.
SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD
Solution ID
TAUS0808281EN*
Solution Usage
Description
PROBLEM:
The scan operation is pulling in the document and flipping for the second side which slows down the scanning by doubling it.
Solution
CAUSE:
This is a product limitation.
SOLUTION:
Work around, if originals are 8.5x11r and 8.5x14, place a legal cover sheet or blank and do not select mixed original. The scan settings will stay simplex
and will scan the legal size for all.
SPECIAL NOTE: Solution contribution by Don St. Onge, Workgroup/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
11
bizhub 360
Solution ID
Controller - no or slow print, scan failure, garbled data, lockup
TAUS0900125EN*
Solution Usage
Description
FK-502, R40 error during communication with CS Remote Care.
Solution
CAUSE: Faxcontroller bug.
SOLUTION: Please install attached fax controller program version G01-11 or later. Refer to the attached Release Notes prior to installation. To view a PDF,
Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Note : The latest version of firmware andsystem software is also available via the Konica Minolta Download Selector. Access the Selector from SSD Web
Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
Solution ID
TAUS0900943EN*
Solution Usage
Description
No Address Found when performing LDAP search to Netware server
Solution
CAUSE:The attribute "statusMember"on the Novel LDAP server was missing or bad.
SOLUTION:Using iManager, under LDAP,find the attribute"statusMember"and map the attributeStatusMember to member:x-status. Click OK.The names
should start to be pulled in the LDAP search.
SPECIAL NOTE: Solution contribution by Paul Santangelo, ESS/BSE
Solution ID
TAUS0901613EN*
Solution Usage
Description
Select job cannot be deleted when deleting a job from the job list. Deletion rights not granted. User authentication is enabled on the machine.
Solution
CAUSE: This is normal for when User Authentication is enabled. User that is trying to delete the job is either not logged in or a different user then the sender.
Solution: Log into the machine if you are the sender before selecting the job to delete. Users only have rights to delete their own jobs.
SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD
Solution ID
TAUS0902047EN*
Solution Usage
Description
Unable to format HDD. Promptedfor apassword.
Solution
CAUSE: Corrupted HDD.
SOLUTION: Replace the HD-505, 40GB HDD (Item #16GA).
SPECIAL NOTE: Solution contribution by Don St. Onge SSD Windsor
Solution ID
TAUS0902105EN*
Solution Usage
Description
How to determine the print data stream of a spool file
Solution
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
12
bizhub 360
Controller - no or slow print, scan failure, garbled data, lockup
To determine the print stream that a spool file has been created in, use the following command:
wrkoutq
1. On the resulting screen, locate the queue that contains the spool file. Useoption 5 to display the spool files.
2.On the resulting list, enter option 8 besides the desired spool file.
The attributes for the spool file will be displayed. Page down to the next screen and locate Printer device type. To the right, you will see the data stream type:
*SCS, *IPDS *AFPDS,*USERASCII, or others.
This information is important to determine which print server to use in orderto print the spool file.
SPECIAL NOTE: Solution contribution by Paul Santangelo, ESS/BSE
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
13
bizhub 360
Solution ID
Dirty image - Spots, banding, streaks, smudged or background
TAUS0801871EN*
Solution Usage
4
Description
Black one quarter-inch (1/4")line on the lead or trail edge of the paper when copying or printing.
Solution
CAUSE: Improper position of the charge corona cleaning handle.
SOLUTION: Be sure that the charge corona cleaning handle is at the home position (pushed in all the way).
SPECIAL NOTE : Solution contribution by Craig Blyther, ASG/SSD
Solution ID
TAUS0901103EN*
Solution Usage
Description
Copy quality issue from Doc feeder only. Marks on output.
Solution
CAUSE: Incorrect settings
SOLUTION:
Perform the following:
1. Access Tech rep mode.
2. Select System 1.
3. Touch Initialization.
4. At the top left, Utility/Admin data settings should be highlighted.
5. Select Job Memory, then press Start, when completed.
6. Select the fourth selection, Service Mode Setting, adjust data and touch Image Process.
7. Press start when completed to do next by itself.
5. Select Machine ADF, adjust data, then back out of the Tech Rep mode.
Note: If this initialization does not resolve, replace DF607 (p/n 16EA -9311) if the issue is not then resolved,replace the PRCB (p/n50GA -902 0E),IMB
(OACB) (p/n 50GA -930 3)
See attachment DF607 sample
SPECIAL NOTE: Solution contribution by Don St. Onge SSD Windsor
Solution ID
TAUS0901902EN*
Solution Usage
Description
Poor image quality when scanning using RightFax®.
Solution
CAUSE:Scan settings can improve the image quality and should be changed
SOLUTION:Set the Text/Photo Mode ON with the procedures below:
1.Press the Scan button on the operation panel.
2.Touch Scan Settings (lower left).
3.Touch Original Type.
4.Touch and set Text/Photo to set ON.
Note :The Text/Photo Mode can be set to default with the procedures below:
a. Service Mode => System2 => Network FAX Settings. In the Network FAX Setting screen, press "ON" the Internet FAX.
b. Administrator Setting => Network Setting => Network FAX Settings => Network FAX Function Settings.In the Network FAX Function Setting
screen, press "ON" the internet FAX.
c. Press FAX button to go to the FAX screen.
d. In the FAX screen, press Scan Setting and chose "Text/Photo" of the Original Image Type => "OK".
e. Utility => User Setting => Initial Setting. In the Initial Setting, select Current Setting and press "OK".
f. Administrator Setting => Network Setting => Network FAX Settings => Network FAX Function Setting.In the Network FAX Function Setting screen,
press "OFF" the internet FAX.
g. Service Mode => System2 => Network FAX Setting. In the Network FAX Setting screen, press "OFF" the internet FAX.
h. Turn OFF/ON the main switch.
SPECIAL NOTE : Solution contribution by Stu Dern, ESS/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
14
bizhub 360
Solution ID
Image blank or solid color
TAUS0653472EN*
Solution Usage
30
Description
C-2803 (C2803)with poor copy quality/jamming.
Solution
PROBABLE CAUSES:
1.The developer drive belt has fallen off, so the agitator drive gear does not turn.
Reinstall and adjust the tension of the drive belt for the agitator drive gear. If necessary, replace the Developing Drive Pulley-Lower 45t (p/n 50GA 1565 0).
2.TCR output abnormality.
Replace TCR sensor (p/n 26NA 8804 1).
3. TheHV supply unit has failed.
Replace the HV supply unit (p/n 50GA84010).
Note : Developer is also being pulled from the developing unit to the drum.
4. Pulling developer onto the drum andcopies or constant jamming at the registration rollers andconstant failing of the PRCB after it is replaced due toshorted
Toner Addition Solenoid (SD5).A longer screw wasinserted for solenoid which shorts the windings in the solenoid. Longer screw inserted when the C-2803
modification is installed or the assembly is removed.
Replace the PRCB (p/n 50GA-9020E), the toner solenoid (p/n 26NA82513) and install shorter screws.
Note : Please refer toattached documentation for solenoid location. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be
downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
5. Toner is not being added to the developing unit due to the toner supply motor (M4) not being turned on. The PRCB has failed.
Replace the PRCB (p/n 50GA-9020E).
6. Firmware update required if still using an earlier version. TCR adjustment should also be run.
Note : Usually occurs when C-2803 or C-2801 error message is indicated at the time of setup.
Please install the latest firmware which is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert
Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
To run the TCR adjustment:
1. Sub Power Switch OFF/ON.
2. Get into "Service Mode".
3. "Service Mode Screen" =>Press [Imaging Process Adjustment].
4. "Process screen" =>Press [TCR Adjustment].
5. "TCR Adjustment screen" =>Press the Start Key.
Solution ID
TAUS0657865EN*
Solution Usage
17
Description
During copy or print jobs, output may be faded (light), washed out, have blank streaks or is blank. C-2702 (C2702) error may alsobe indicated.
Solution
PROBABLE CAUSES:
1. Improper contact of transfer power supply plate.
Inspect the transfer power supply plate (p/n 50GA 5051 0) to ensure that proper contact is being made. The plate islocated at the lower left corner of the right
side conveyance door. Contact is made at two locations- one with the copper plate at lower left of main body near the white supply wire and the other with
transfer contact spring.
2. A transfer arcing/short abnormality. If the phenomenonis generated 5 consecutive times for three cycles the code is generated. Usually the transfer
separation corona assembly shorting generates this code, however, the issue can include the blocks and the actual HV unit itself.
Replace the transfer separation assembly (p/n 50GA-2600). If this fails to resolve the issue, the corona end blocks should be replaced (p/n 50GA 5053 0).
And if the issue still continues, the HV unit should be replaced (p/n 50GA 8401 0).
3. Internal arcing within the main body high voltage connecting plate assembly. C-2703 (C2703) code may also be indicated.
Inspect the main body high voltage connecting plate assembly for signs of arcing. Clean, insulate, or replace the cover plate (p/n 50GA-7380), high voltage
connecting plate S assembly (p/n 50GA-7510), electrode connecting springs A (p/n 26NA 7325 1), contact pedestal 1 (p/n 50GA 7342 0), and high voltage
connecting plate B assembly (p/n 26NA R712 00) as necessary.
4. Poor grounding of the T/S corona.
Ensure thatthe ground plate (p/n 1164 2155 01)is making good contact.Replace the T/Sassemblyif the problem persists (p/n 50GA-2600). Please refer to
attached page from Parts Manual as a reference. To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the
Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
5. The grounding tabs located on the lower left side of the side fuser door could be bent. When closing the side fuser door, check to see if the grounding tabs
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
15
bizhub 360
Image blank or solid color
meet on the adjacent grounding plate. If the tabs are bent they may be pushed up over the plate instead of down onto the plate.
If the grounding tabs do not meet the grounding plate, bend the tabs down slightly. This puts them in the proper position to meet the grounding plate.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
16
bizhub 360
Solution ID
Image delay, advance, shift or skew
TAUS0801870EN*
Solution Usage
Description
Cutting off about a half-inch when copying/printing on all paper sizes.
Solution
CAUSE:Incorrect positioning of the dust proof glass cleaning rod.
SOLUTION: Be sure that the dust proof glass cleaning rod, shown on page 26 in the Field Service (Maintenance) section (see attached), isinstalled correctly
and completely pushed in.
Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Craig Blyther, ASG/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
17
bizhub 360
Solution ID
Image failure other than density/color - magnification, blur
TAUS0802584EN*
Solution Usage
0
Description
When printing 3-D or MaxiCode barcodes from AS/400® or mainframe, the job does not print correctly.
Solution
CAUSE: There are too many variables for the HPT on a HOST system to correctly image a UPS shipping ticket and 3-D MaxiCode barcode.
SOLUTION: Use a LinkCom™ III with the following configuration:
The configuration can be set up using PrintGuide™.
Set up the LinkCom™ III to support IP40 emulation and install the IP40 font set.
Under the IPDS tab select the following settings.
- Postscript
- Edge-to-Edge is on
- Report Margins to system is on
- 37 code page
- IP40 emulation
- 600dpi
- VPA is set to Physical
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/BSE
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
18
bizhub 360
Solution ID
Image too light, dark, uneven or wrong color
TAUS0657269EN*
Solution Usage
3
Description
Uneven density on the edge of copies.
Solution
CAUSE: Failure of the Developing Unit, specifically, the Developing Roller.
SOLUTION: The Developing Roller is not an available part, therefore the entire Developing Unit must be replaced (p/n 50GA -300 1).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
19
bizhub 360
Solution ID
Image voids or deletions
TAUS0808398EN*
Solution Usage
0
Description
Blank copies and the drum will not turn.
Solution
CAUSE: The dumper plate assy. is broken.
SOLUTION: Replace the dumper plate assy. (p/n 50GA-1550).
SPECIAL NOTE: Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0808339EN*
Solution Usage
Description
Cutting off a half inch on all paper sizes, regardless of paper size.
Solution
CAUSE: Incorrect installation of the bluecleaning handle on the charge corona. It was put on the wrong way.
SOLUTION: Reinstall the cleaning handle correctly.
SPECIAL NOTE: Solution contribution by Craig Blyther, ASG/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
20
bizhub 360
Solution ID
Miscellaneous
TAUS0700453EN*
Solution Usage
796
Description
NVRAM Troubleshooting Procedure used to identify NVRAM problems and and information concerning damaged or missing NVRAM/BRU.
Solution
bizhub C250/C252/C300/C350/C351/C450
NVRAM trouble codes (C-D3xx codes) can occur at any time. Mostly these codes happen when updating firmware. A NVRAM Data Restore procedure was
announced a few months ago to address these codes:
Stop, 0, 7, 1, 3, 9, *
What this procedure does is take a good image of the NVRAM off the MFP board (created when you performed the NVRAM Data Backup) and restore it to
the NVRAM. There are approximately 30 registers that can be corrupt, so the above procedure may have to be done as much as 30 times.
WARNING : If a corrupt NVRAM is suspected, DO NOT perform the NVRAM Data Backup. This will take the corrupt NVRAM image and back it up to the
MFP board. If this is done, and the NVRAM is replaced, the corrupt data that was just backed up will be transferred to the new NVRAM. If this is the case,
then the NVRAM and MFP board will have to be replaced as a set.
Known unrecoverable NVRAM symptoms:
1. Stuck on hourglass screen
2. Incorrect meters
3. When performing the NVRAM restore procedure the codes repeat themselves
Note : One thing that has been noticed is these machines seem to be highly susceptible to voltage sags and spikes. It is HIGHLY recommended to install a
quality power line conditioner on these machines.
Known fixes for various codes:
C-D36E and C-E002 – Install Phase 3.01 firmware (H5 or H6 depending on model).
If a corrupt NVRAM is suspected, please try performing a Data Clear. This can be found in the Tech Rep mode.
CAUTION : All programmed addresses will be cleared. Please backup the address data using PageScope Web Connection to backup the data before
performing the Data Clear. If NVRAM replacement is necessary please be aware that the meters may not be transferred and they might be reset to zero. This
is unrecoverable and the correct meters cannot be input.
8020/CF2002/8031/CF3102
Codes C-3C00 through C-3C40 indicate a corrupt BRU.
Codes C-3C50 through C-3C90 indicates a problem with the PWB-C board or the scanner to main body cable.
8050/CF5001/bizhub PRO C500
The NVRAM for the C500 cannot be replaced in the field. The only way to correct a corrupt NVRAM is to send the OACB, NVRAM, and PRCB into Konica
Minolta to be reset.
Known defective NVRAM symptoms:
1. Meters or default adjustment values are extremely high.
2. Adjustments do not hold after powering the machine OFF/ON.
Note : On the Black and White machines verify that the NVRAM is bad by swapping a good NVRAM from another machine in the same product family. This
will save significant time and expense in getting back the machine in working condition.
bizhub 200/250/350
Common symptoms when NVRAM replacement may be necessary:
1. Machine not going to ready state.
2. Not printing to a host name with DHCP.
3. Not scanning to E-mail.
4. On startup, abort code 0x0000999a .
5. Abort code 0x00f00b00 .
6. Not printing.
7. Machine rebooting every few minutes.
8. Screen freezing in Konica Minolta logo.
9. Keep losing machine settings when power OFF.
bizhub 420/500
Common symptoms when NVRAM replacement may be necessary:
Note : First try to flash the machine to the latest firmware before swapping the NVRAM because the firmware fixes many of the following symptoms:
1. Screen freeze in Konica Minolta logo.
2. Fax unit locking up theMFP or not recognized.
3. C-E084 error code.
4. Cannot PING the MFP.
5. C-D203 error code.
6. Display resetting to Japanese.
7. Losing network settings after firmware upgrade.
8. C-E002 error code.
9. Scan to E-mail or FTP.
10. Loss of adjustment data.
11. Total counter is reset.
12. Display TCR adjustment.
13. C-284x error code.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
21
bizhub 360
Miscellaneous
bizhub 600/750
Common symptoms when NVRAM replacement may be necessary:
1. Screen freeze in Konica Minolta logo.
2. Cannot recognize document feeder.
3. Error code SC2203 .
7145/7255
Common symptoms when NVRAM replacement may be necessary:
1. Blank screen.
2. Loss of E-mail addresses.
3. Loss of settings.
4. Error code E56-01 .
Ordering Procedures
Call the SSD Hotline at 800-825-5664, to open a Problem Ticket.
IMPORTANT : All requests for NVRAMs must be approved by the SSD Hotline and a problem ticket generated.If a request is received without an
established problem ticket number the request will be denied.
The NVRAM can be ordered via the Online Technical & Special Program order form located within MyKonicaMinolta.com:
1. Login to MKM.com.
2. Select the Service tab.
3. Select Warranty, Repair, & Special Programs (menu at left side of screen).
4. Click on Warranty Services & Technical/FOC Programs (in center of screen).
5. Select NVRAM/BRU Replacement Program.
Updates/Status
Call Logistics at 201-934-5339.
Notes :
a. Refer to the attached RA formand Bulletin Number 5783 for more detail.The bulletin may be a bit out-of-date concerning actual ordering procedures and
applicable models.
b. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Clinton Marquardt, ESS/SSD and Cesar Jimenez and Ed Bellone, Production Print/SSD
Solution ID
TAUS0701604EN*
Solution Usage
50
Description
NVRAM/BRU replacement form.
Solution
The online NVRAM/BRU Replacement RA/Claim formis referencedin attached Bulletin Number 5783.
Notes :
1. AN SSD TICKET NUMBER MUST BE ASSIGNED IN ORDER TO PLACEA NVRAM/BRU ORDER ONLINE. All requests for NVRAMs must be approved
by the SSD Hotline and a problem ticket generated. If a request is received without an established problem ticket number, the request will be denied.
2. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Ed Bellone, Production Print/SSD
Solution ID
TAUS0800104EN*
Solution Usage
43
Description
VoIP TX/RXsolutions.
Solution
More and more customers changing their PBX systems from analog or ISDN to VoIP-based PBX systems.
Note : A digital-to-analog converter can be usedand will work, but Konica MInolta will not provide any support if there arephone/fax issues.
Due to the general incompatibility of fax and VoIP,certain settings may not work. The problem is not caused by the Fax Unit, butis caused by:
the general design of VoIP using TCP/IP Packets
VoIP PBX systems
the general specification of VoIP and it's
* Codecs
* Coding an decoding timings
* Fax fixed timings
* LAN Packet losses
* Quality of Services
* ITU/RFC Specification implementation
* Bugs
* Interpretation of technical terms within the specifications of the ITU-T and RFC documents.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
22
bizhub 360
Miscellaneous
VoIP is still not supported offically by Konica Minolta, but may work in some instances.
Performing these suggested settings may solve the problem.Follow the operation made step-by-step:
From Service Mode
==> FAX Settings
==> Communication
==> Protocolset "ON" the "V.29 EP Tone" Protocol
and set "OFF" all other faster protocolls.
From Service Mode
==> FAX Settings
==> Communication
==> Others we have set "OFF" the "ECM Function"
From Service Mode
==> FAX Settings
==> Function Parameter
==> Address "0e0012 = 01111000
(Hex 78 = 120 sec)
(T1 Timer for Calling)
From Service Mode
==> FAX Settings
==> Function Parameter
==> Address "0e0013 = 01111000
(Hex 78 = 120 sec).
(T1 Timer for Called)
From Service Mode
==> System 2
==> Software Switch
==> SoftSwitch 21 Bit5=1
00100000
(HEX 20 = over 4.5 sec)
(T4 Waiting time between start Identification)
Notes:
a. Before performing the above mentioned settings it is recommended to upgrade the firmware to the latest version and to check if the FK-502 will have the
latest available version. The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD
Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
b.Expect more communication problems than on anISDN or analog line (approximately 15% more).
Workaround :
If the aforementioned settingsdo not showan acceptable result,offer as alternative:
Unimessage Pro Fax Server Solution where Scan to E-mail with auto prefix-suffix setting is used (depending on the machine Series - prefix-suffix will be
added automatically or can be selected manually).
RightFax Server with "Setup Utility for RightFax" using OpenAPI.
SPECIAL NOTE : Solution contribution by KM Europe (BEU) and Cesar Jimenez, Production Print/SSD.
Solution ID
TAUS0801227EN*
Solution Usage
24
Description
NVRAM replacement.
Solution
For NVRAM replacement, please follow these instructions:
CAUTION : Once a NVRAM is installed in an MFP and the MFP is powered up, the NVRAM is no longer useful for any other MFP. As a general rule,
swapping a NVRAM between different MFPs is not allowed. NEVER replace a NVRAM from a different model or from any model with a different firmware
version.
bizhub C650/C550/C451/C353/C253/C203
To replace a NVRAM;
1. Install new NVRAM in the MFP.
2. Power ON the MFP.
Note : When installing new NVRAM and turning on MFP first time, NVRAM is initialized according to the model/firmware version of the MFP in which the
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
23
bizhub 360
Miscellaneous
NVRAM is installed. While initializing, a hourglass screen is displayed for about 90 seconds. Do not power OFF the MFP while the hourglass screen is
indicated.
3.Make following setting correctly in Service Mode.
System1 => Marketing Area
System2 => HDD
System2 => Option Board Status
System2 => Image Controller Setting
System2 => Software Switch Setting (required for bizhub product only)
* Switch Numbe 10
* Hex Assignment: 02
4.Power OFF/ON the MFP.
5.Do the setup procedure instructed in the Installation Manual.
Please refer to attached documentation for details.
7145/Di451
Please refer to attached documentation fordetails.
bizhub 500/420/360
Please refer to attached documentation fordetails.
7165/7155/Di650/Di551
Please refer to attached documentation fordetails.
7272/7255/Di7210/Di5510
Please refer to attached documentation fordetails.
bizhub 750/600
Please refer to attached documentation fordetails.
Note : To viewa PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0800962EN*
Solution Usage
22
Solution Usage
19
Description
SERVER CONNECT ERROR message and unable to scan to E-mail viaMicrosoft® Exchange Server 2003 and 2007.
Solution
CAUSE: An exception for the printer was not added to the Microsoft® Exchange Server.
SOLUTION: Have theserver Administrator add an exception for the printer to the Exchange exceptions list.
1.Open the Control panel and select Windows Firewall.
2.Select Exceptions and Add Port.
3.Add a name and Port number.
4.Click on Change Scope.
5.Select Custom List and add the TCP/IP address for the exception.
SPECIAL NOTE : Solution contribution byMalcolm Hibbert, Workgroup/SSD and Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0701261EN*
Description
How to set up Scan to SMB in Microsoft® Windows Vista™.
Solution
Microsoft® Windows Vista™ has a Public Folder Sharing function to make the setup easier than the previous OSs. Follow the procedures below.
At the Workstation/PC :
1. Right-click on the Network icon on the desktop.
2. Select Properties.
3. In the Network and Sharing Center, and then under the Sharing and Discovery title, click on Public Folder Sharing.
4. Click on 'Turn on sharing so anyone with network access can open, change, and create files'.
5. Click Apply (Click Continue to the 'Windows needs your permission to Continue' message).
6. Create the folder and set to share. Click on the 'This Computer' icon in the Network and Sharing Center to display the available hard drives or local disk(s).
7.Double-click on the desired disk and create a new folder.
8.Right-click on the new folder and select 'Share…In the File Sharing' dialog box. Make sure the desired user(s) are displayed and/or added as needed. Set
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
24
bizhub 360
Miscellaneous
the permission level to Co-owner to allow writing rights.
9.Click on Share and then (Click 'Continue' to the 'Windows needs your permission to Continue' message).
At the engine (direct input) :
1. Press the Scan button on operation panel.
2. Touch Direct Input tab.
3. Touch Scan to SMB.
4. In the host name field enter theTCP/IP address of the target PC.
5. In the Destination Folder enter the shared folder name.
6. in the User ID field enter the valid workgroup or domain User Name.
7. In the Password field enter the user Password.
8. Press Start.
Note : For more information on Microsoft® Vista™ File and Printer Sharing technologies, go to
http://www.microsoft.com/technet/network/evaluate/vista_fp.mspx
SPECIAL NOTE : Solution contribution by Jim Behrends, Mark D'Attilio and Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0801968EN*
Solution Usage
13
Description
FK-502, Fax Forward function.
Solution
To use the Fax Forward function with an installed FK-502, the incoming fax can be sent to:
Fax
E-Mail
FTP
SMB
Box
To be able to forward a Fax, E-Mail, FTP, SMB or Box, store the recipient into the machine in advance.
Check the functionality of the stored recipient in advance before using it within the Fax forward function.
To store an E-Mail address for Fax forwarding to E-Mail:
1. Enter a One Touch Dial, Fax, FTP or SMB recipient via [Utility/Counter]=> One Touch Registration => Scan => Address Book => E-Mail =>
New.
2. Enter a NAME for the Button.
3. Enter the E-Mail address.
4. Press OK.
5. Press Close 4 times.
Enable the Fax forward function via [Utility/Counter] => Administrator setting => Password => Fax Setting => Function Setting => Fax Forward
=> Select from Address Book => E-Mail => select your preferred address.
Note :
Speed Dial , E-Mail , FTP , SMB and Group is available. Groups may include a Box, but a Box will be ignorred in combination with
forwarding functions.
Known Limitations/Problems :
No sophisticated selective line forwarding if Multi-line is installed. This means, you cannot forward all Fax received on Line 1 to E-Mail Address A and forward
all received Fax on Line2 to Address B.
No Fax forward function to stored "Programs".
No attachment file type selection (TIFF/PDF) for forwarded Fax.
Fax forward to Box and Group at the same time is NOT possible.
Fax Forward to E-mail and FTP/SMB is not possible.
Known Workarounds :
No sophisticated selective line forwarding.
You may use a Fax Server with Installed Unimessage Pro® or RightFax©. The price for a simple Server Hardware (Pentium® 4 desktop) and the
Unimessage Pro® software is nearly the sameas for the Fax Unit (FK-502).
In addition you can sell "Service for UMP" and a "Solution” offering more flexibility and functionality.
RightFax© is more focused on Major Account business and is much more expensive but will provide more functions.
You may use a bizhub 250/350 with FK-503 and Multi-line Kit, because this machine is able to have a sophisticated Fax forwarding function.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
25
bizhub 360
Miscellaneous
If more than one of the above mentioned machines are installed at customer site, each machine can be equipped with a FK-502 and may be used for Fax
forwarding even if there is no Fax Kit needed. But the FK-502 line can be used to forward a Fax to a second address, because the place of the Fax number is
easy to switch within a PBX.
No Fax forwarding to stored programs.
No Workaround available.
No attachment file type selection (TIFF/PDF) for forwarded Fax.
Press the [Utility/counter]=> User Setting => Initial Setting => Current Setting => OK => Close => Close. PDF becomes default for all scans
and attachments (except programmed Program destinations).
Note : The bizhub C353/C253/C203 firmware version 88/E3/G3 is not capable to forward a Fax document with TIFF format. To support this featurei-Option
2/Gx0-J8) is available. This firmware will provides asoft switch to support TIFF/PDF in a different way.
Switch Number: 28
HEX Assignment: 00 Forwarding TX by PDF format [Default]
HEX Assignment: 08 Forwarding TX by TIFF format
Fax forward to a Box and Group membership at the same time is NOT supported
It is a specification limitation that a Group, containing a Box, can be selected, but the Box forward will be ignored.
Fax Forward to E-mail and FTP/SMB within a group is not possible.
SPECIAL NOTE : Solution contribution by KM Europe (BEU) and Ian Lynch/Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0703269EN*
Solution Usage
9
Description
How to set up User Authentication using Active Directory from theMFP and using the driver.
Solution
From theMFP Side:
1. Administrator setting 1,2,3,4,5,6,7,8.
2. System setting.
3. Date/Time setting (also enter correct Time Zone). Use the same time as the server.
EST-Time Zone UTC - 05:00
CST-Time Zone UTC - 06:00
MST-Time Zone UTC - 07:00
PST-Time Zone UTC - 08:00
4. Administrator Setting 1,2,3,4,5,6,7,8.
5. Network setting.
6. TCP/IP settings.
7. FWD to page 3.
8. DNS settings (enter Priority and substitute DNS TCP/IP addresses).
9. Administrator setting.
10. Network settings.
11. Detail settings.
12. Time Adjust settings (NTP Settings - ON, enter TCP/IP address of server).
13. Administrator Mode (1,2,3,4,5,6,7,8).
14. User Authentication/Account track.
15. General settings.
16. ON (External Server).
17. Select Active Directory.
18. Enter the Domain Name.
19. Press Registration.
20. Press OK, OK.
21. Enable Account Track.
22. Choose Account Track Input Method.
23. Choose Account Name & Password.
24. Press OK.
From the computer:
1. Go into the Printers folder or Printers and Faxes.
2. Right-click onthe printer.
3. Select Properties.
4. Select the Option or Configure Tab(may not be available on some models).
5. Make sure that User Authentication is set to ON [Device] (may not be available on some models).
6. Openthe application.
7. Select File.
8. Select Print.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
26
bizhub 360
Miscellaneous
9. Choosethe printer.
10. Select Properties.
11. Select the Setup tab.
12. Choose User Authentication/Account Track.
13. Enable User Authentication.
14. Select Recipient User.
15. Enter the User Login Name and Password (the ones used to login to the Domain).
16. Select OK, OK, OK.
Note : The MFP settings can be performed from the web browser.Time zone and daylight saving settings are critical to allow the MFP to synchronize with
the active directory server.
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD and Jim Behrends, Workgroup/SSD
Solution ID
TAUS0703092EN*
Solution Usage
8
Description
eCopy™ compatible machine models, firmware and TWAIN drivers list.
Solution
Please refer to attached documentation. To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe®
web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Notes :
1. The latest version firmware is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support) by
clicking on 'Download MSDS, Drivers, Firmware and more'.
2. The latest printer drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site
(http://www.kmbs.konicaminolta.us) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD and Bill Hall, Workgroup/SSD
Solution ID
TAUS0703410EN*
Solution Usage
8
Solution Usage
8
Description
ADF control board part numbers are different for the DF-605 and DF-607.
Solution
DF-605 control board (p/n 4344-5206-02) andDF-607 control board (p/n 16EA-9311).
SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/SSD
Solution ID
TAUS0801706EN*
Description
Paper Test requirements.
Solution
For initial test the dealer/branch must supply 1000 sheets of the media paper. Once the paper is received the ticket is transferred to ESS.
If the initial test does not have any issues then a second test can be done. The dealer/branch must supply enough media to cover 1/3 of a PM cycle. There is
a charge involved to cover labor and supplies. The dealer/branch will be notified byESS before the test to communicate the charges.
SPECIAL NOTE : Solution contribution by Cesar Jimenez and Ian Lynch, Production Print/SSD
Solution ID
TAUS0645779EN*
Solution Usage
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
7
October 2009
27
bizhub 360
Miscellaneous
Description
How toperform a Data Capture (Print Capture)on MFPs when printing using the Emperon controller.
Solution
Note : This procedure is used when you are having a printing issue only.
The following must be set up in order to capture the files:
1. Press the utility button and select Administrator Settings.
2. Select Security setting => Security Detail => Print Data Capture must be set to Allow =>
Administrator Settings => Network Setting => FTP setting, FTP Server must be set to ON.
3. In Tech Rep Mode, select System2 and select Data Capture. Select ON.
4. Send print jobs. When finished, enter Command prompt and run FTP client.
5. Issue OPEN ipaddress command and login as the following user
capture
sysadm
6. Type lcd \ command to set the local directory to root of C: drive.
7. Use the ls command to list the files.
8. Type binary to change the transfer mode to binary.The response should be 200 .
9. Type set to I .
10. Use the get command to retrieve the files (i.e., get c741n.cpt). This will transfer the file tolocalC: drive.
11. After complete enter the bye command.
12. Type exit to quit the command prompt.
To delete the jobs on the HDD,select administrator settings => Security Detail => Restrict.
The function will remove the files from the printer.
Note : Please refer to attached pages from the Field Service Manual/Service Modeconcerning Data Capture. To viewthe PDF, Adobe Reader® must be
installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Jim Behrends and Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0653347EN*
Solution Usage
7
Solution Usage
7
Description
How to reset the administrator password.
Solution
To reset the administrator password, perform the following:
1. Press the [Utility/Counter] key.
2. Touch [Details].
3. Press [Stop 0,0, Stop 0,1].
4. Press [Stop 0, C].
5. Touch [administrator password].
6. Enter the new password.
SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD
Solution ID
TAUS0657076EN*
Description
Parts required to connect a Hecon® conventional key counter, Hecon® Base 10or legacy Minolta key counter to the main body.
Solution
Please see attached Bulletin Number 5563 for details.
Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0702838EN*
Solution Usage
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
7
October 2009
28
bizhub 360
Miscellaneous
Description
How to create a device printer on an AS/400® system using SCS over LAN.
Solution
To Create a Device Description on AS/400® to print to KMBS printers perform the following:
1. From the Main Menu under Selection or Command, type: CRTDEVPRT <enter>.
2. Change the following to set up the printer (those settings not changed, keep at default):
a. Device Description - (name the printer i.e., KMPrinter)
b. Device Class - *LAN
c. Device Type - 3812
d. Device Model - 1
e. LAN Attach - *IP
f. Port number 9100
g. Font Identifier - 011
h. Form Feed - * Autocut
i. Manufacturer - *HP5si
j. Paper Source (both) - *letter
k. Address - (TCP/IP address of the NIC)
l. User Define Option - *IBMSHRCNN
m. System Driver (hit F4) - *IBMSNMPDRV or *HPPJLDRV if SNMP is disabled in the environment.
Note :Vary ON the device to allow attachment.
SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD
Solution ID
TAUS0649964EN*
Solution Usage
6
Description
Setting the default file type to PDF or TIFF in Scan mode.
Solution
To set the default file type for the Scan mode, perform the following:
1. Before accessing the Setting menu, press [Scan] and change the file type from [TIFF] to[PDF] on the operation touch panel.
2. Select [Utility/Counter] => [User Setting] => [Initial Setting]. Change from [Factory Default] to [Current Setting] and press OK.
3, Return to the basic screen.
Note : This is the basic procedure for default change,not only for the scan file type, but also the copy mode. For more detail, please see attached Copy
Operations User Guide pages. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0657371EN*
Solution Usage
6
Description
Citrix© compatibility.
Solution
Please refer to the attached Citrix© compatibility list for additional information.Some products not listed below arelisted in the attached document.It covers
other MFPs and Controllers like the bizhub C350/C353/C253/C203, the bizhub PRO 1050/920, the bizhub
600/601/750/751/360/361/362/420/421/500/501/162/180/210/222/282, IC-303 and IC-409.
To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
IC-202
Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation™ Server 3.0 environments with the Microsoft® Office, Microsoft®
Excel and Adobe® Acrobat® 6.0 applications loaded. When utilizing the PostScript Visual driver version 1.0.1, the Adobe® PostScript driver version 1.0.0 or
the PCL driver version 1.01 the print controller can be used without restrictions.
IC-203
Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Presentation™ Server 3.0 environments with the Microsoft® Word 2003/Excel 2003 and
Adobe® Acrobat® 6.0 applications loaded. When utilizing the PostScript Visual driver version 2.0.28, the Adobe® PostScript driver version 2.0.28 or the PCL
driver version 2.0.0, the print controller can be used without restrictions.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
29
bizhub 360
Miscellaneous
IC-205
Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation™ Server 3.0 environments with the Microsoft® Office, Microsoft®
Excel and Adobe® Acrobat® 6.0 applications loaded. When utilizing the GDI driver version 1.00 or the PCL driver version 1.00 the print controller can be used
with the following restrictions:
1. Cancelled print jobs may stay in queue when using the GDI driver.
2. The printer icon may disappear when cancelling a print job when using the GDI driver.
3. Print jobs may hang when printing from two or more workstations simultaneously using the GDI driver.
IC-302
Tested withCitrix© Metaframe™ FR3 on Microsoft® Windows 2000 and 2003 Server, using PostScript version 1.1.
Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6. The only restrictions found were that Owner Information functions were
not available.
IC-401
Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation Server™ 3.0 environments with the Microsoft® Word 2003, Excel
2003 and Adobe® Acrobat® 6 applications loaded. Testing has been performed with the PostScript driver version 1.0.
The following restrictions:
1. The mixed media function may not be used.
2. Enabling the "Delete pending print jobs at logout" on the Metaframe™ server does not result in the print jobs being deleted.
3. Print job access codes should not be used.
IC-402
Tested withCitrix© Metaframe™ FR3 on Microsoft® Windows 2000 and 2003 Server, using PostScript version 1.0.
Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6. The following are restrictions that were found:
1. Custom Size setting is not available.
2.Owner Information, Lock Job and Copier store print functions are not available.
3. The client default settings are not saved.
IC-405
Tested withCitrix© Metaframe™ FR3 on Microsoft® Windows 2000 and 2003 Server, using PostScript version 2.0.
Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6. The only restrictions found were thatMedia Mixed function is not
available by network printer.
IC-611
Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation Server™ 3.0 environments with the Microsoft® Office, Microsoft®
Excel and Adobe® Acrobat® 6.0 applications loaded. When utilizing the PostScript Visual driver version 1.0.0.7, the PostScript Adobe® driver version 1.0.0.7
or the PCL driver version 1.0.1 the print controller can be used with the following restrictions:
1. The watermark function will not function when using the PCL driver.
2. The PostScript Visual driver is not available with Microsoft® Windows 2003 Server.
3. Booklet mode may not function when called within Adobe® Acrobat®.
IP-901
Tested withCitrix© Metaframe™ FR3 on Microsoft® Windows 2000 and 2003 Server, using PostScript version 1.1 and 2.1.
Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6. The only restrictions found were that Owner Information functions were
not available.
bizhub C350 Standard Controller
Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation Server™ 3.0 environments with the Microsoft® Word 2003, Excel
2003 and Adobe® Acrobat® 6 applications loaded. Testing has been performed with the PCL driver version 1.0 with the following restriction:
The watermark feature will not be available on a locally installed printer.
bizhub 200/250/350 Standard Controller
Tested in both the Citrix© Metaframe™ XP (FR3) and the Citrix© Metaframe Presentation Server™ 3.0 environments with the Microsoft® Office, Microsoft®
Excel and Adobe® Acrobat® 6.0 applications loaded. When utilizing the PostScript Visual driver version 1.0.1 or the PCL driver version 1.0.2 the print
controller can be used with the following restrictions:
1. The custom paper size setting is not available.
2. The default selections made on client workstations will not be reflected on the printer properties screens.
bizhub C650/C550/C451/C450/C352/C351/C300/C252/C250
Tested withCitrix© Metaframe™.
Applications tested were Microsoft® Word 2003, Excel 2003 and Adobe® Acrobat® 6.No restrictions were found in testing.
Solution ID
TAUS0800508EN*
Solution Usage
6
Description
Where to find paper recommendations for specific models.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
30
bizhub 360
Miscellaneous
Solution
Please refer to the attachedMedia Guides for the products listed. It can also be found on the MyKonicaMinolta.com web site by following the procedure
below:
1. Log into the MyKonicaMinolta.com web site.
2. Click on "Products."
3. Click on "Supported Models Library."
4. Select "Office Systems" in the pull down menu for Category and select the appropriate product.
5. Click on the link for "Support Materials" and scroll to the link for the Media Guide Office Workgroup Products.
Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0801324EN*
Solution Usage
6
Description
Supporting bizhub vCare.
Solution
Initial setup documents for vCare support are attached. The attacheddocuments were sent to all the BSCs. This information is for the BSCs only. It does not
apply to dealers.
Notes :
1. Please be aware that the bizhub C203/C253/C353/C451/C550/C650 support one-way communication.
2. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD
Solution ID
TAUS0648443EN*
Solution Usage
5
Description
How to remove print drivers from Macintosh® OS X, 10.2x, 10.3x, 10.4x, 10.5x.
Solution
Follow the How to remove Macintosh OS X drivers instructions to correctly remove driver files prior to installing a new or updated version of the driver. This
is highly recommended to avoid driver conflict.
Completely deleting\removing the PPD plug-ins for the loading of the driver will NOT overwrite the previous versions.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Bill Ehmke, ASG/SSD and Freddie Burnham/Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0801272EN*
Solution Usage
5
Solution Usage
5
Description
Support for Account track, Secure print, and User authentication from Unix/Linux environments.
Solution
Konica Minolta does not support Account track, Secure print, and User authentication from Unix/Linux environments at this time.
The availability of these options for Unix/Linux environments is being considered for future development.
Please attachticket to this solution and provide the following information;
1. Product model number(s).
2. Now many products placed or being considered for placement.
3.What "flavor" and version of Unix/Linux operating system.
SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS/SSD
Solution ID
TAUS0900739EN*
Description
How to load a 64-bit driver on a 32-bit Server system (Microsoft® Windows 2003 Server/Vista™).
Solution
Please follow this step-by-step procedure and refer to the attached video.
1. Load the 64-bit driver on the client.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
31
bizhub 360
Miscellaneous
2. Load the 32-bit driver on the server and share it out.
Note : If you receive a pop-up indicating “COPY ERROR”, setup cannot copy this file. Example: KOZJA_.PP_. This could possibly be a file path length
limitation. Try reducing this limitation by pulling out the specific driver needed and placing it on the desktop.
3. From the 64-bit client perform the Run command to connect to the 32-bit server (example: \\11.11.5.33) and press enter.
4. Double-click on the shared out printer.
5. Select printer and then properties.
6. Select the Sharing tab and click on the additional drivers box.
7. Select or check-off the 64-bit (x64) driver to be added to the 32-bit server.
8. Select OK and the 64-bit driver should be pushed up to the server.
9. Check the additional drivers of the client and server to confirm that the x86 (32-bit) and x64 are both installed.
Notes :
a.This was tested on like versions of 32-bit and 64-bit drivers.
b.To viewthis procedure, Apple© QuickTime®should be installed.It can be downloaded for free at http://www.apple.com/quicktime/download/ .
SPECIAL NOTE : Solution contribution by Freddie Burnham, Production Print/SSD
Solution ID
TAUS0627763EN*
Solution Usage
4
Description
Vellum paper specifications.
Solution
Vellum paper is outside of the special paper specifications of the machine therefore specific paper specification can not be provided. The paper may run
though the machine, however Konica Minolta does not support a particular brand of vellum paper.
Note : Vellum paper has tendencies to hold a static charge causing the paper to have transfer problems with possible premature wearing of the drum. This
paper, in some cases is coated, and could possibly lead to premature wearing of the fuser rollers or leave marks on the copies.
Solution ID
TAUS0652780EN*
Solution Usage
4
Solution Usage
4
Description
How to access Tech Rep Mode while machine is displaying an error code.
Solution
To enter the Tech. Rep. mode through Trouble reset, perform the following:
1. While powering the machine ON, hold down the Utility/Counter key until Trouble Reset screen appears.
2. Press Stop-0-0 Stop-01.
3. In Tech. Rep. mode, select System 1, then Initialization andthe Utility/Admin setting data will be highlighted.
4.Select on right column, Job Mem Setting Data, Fax Setting data, Network setting data and press Start when it indicates Complete.
5. PressOK.
Note : If it does not complete and indicates Failed, this isstill acceptable. One area was not corrupt and did not reset.
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0656962EN*
Description
Connecting a Hecon® (key counter) device to the mainbody.
Solution
Please seeattachedBulletin Number 5563inregards to Hecon® conventional key counter, Hecon® Base 10 and legacy Minolta key counter support. To
viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0701643EN*
Solution Usage
4
Description
New firmware release for support of eCopy™.
Solution
New firmware has been released for support of eCopy™ functions.
bizhub 360/420/500 and IC-204
Firmware level is Version 31-UL (Base Version: C 31)
bizhub 600/750 and IC-202
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
32
bizhub 360
Miscellaneous
Firmware level is 57AA-1000-GUJ-30-000, Version 30-UJ.
Notes :
1. Please usethe firmwareat the same time as Konica Minolta TWAIN Driver for eCopy™ (NoGUI), Version 2.0.11d.
2.The latest version of firmware, system software or print drivers is available via the Konica Minolta Download Selector. Access the Selector from SSD Web
Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0702178EN*
Solution Usage
4
Description
SC2804 after replacing the toner supply section.
Solution
CAUSE: The Toner SupplyStopper Spring (p/n 50GA32700 ) is not in the proper position.
SOLUTION: Ensure to place the Stopper Spring intoproper position. For proper spring position, please review the pictures attached to this solution.
Solution ID
TAUS0702294EN*
Solution Usage
4
Description
How to configure LDAP access on a Lotus® Notes R5 or R6 server.
Performing a LDAP Search using an Anonymous Connection via Lotus Notes.
(supportedLDAPVersion) not enabled.
Solution
LDAP Production R5/R6 server setup :
1. Edit Notes.ini and add LDAP task. ServerTasks = Router, Replica, Update, Amgr, AdminP, CalConn, Event, Sched, Stats, HTTP, POP3, maps, LDAP.
2. Create a new Configuration document for LDAP to control Anonymous Access.
3. Create a new Configuration doc, call it Allservers in the Group or Server name, then save and close the doc.
4. Now open the Allservers doc. Note that the Basics tab has changed.
5. Select Use these settings as the default for all servers. Note that Group or Server name is now *-Default-. Also there is now an LDAP tab.
6. Click on the fields that you want to be accessible button.
7. Set it to show First Name InternetAddress and LastName only. Do this so only limited info is available.
Notes :
a. If you upgrade a server from a previous release to Lotus® Domino 6, the LDAP service uses the LDAP anonymous access configuration from the previous
release. If you create or edit the domain Configuration Settings documents after updating the directory with the Lotus® Domino 6 PUBNAMES.NTF design,
the list of attributes allowed for anonymous access include the following attributes (attached - ldap1.pdf)not listed in the previous release:
b.The Allservers configuration doc will only affect the servers running LDAP. It will also allow the MFPs to access LDAP without using an authentication
account and password. This is the method that all users are using according to Lotus® Incident 1632724.
c. Please refer to the attached document for more detail.
d. To view the document(s), Microsoft® Word® or Word® Viewer must be installed. Word® Viewer 2003 (11.7MB) can be obtained free from Microsoft® at
the following URL; http://www.microsoft.com/downloads/details.aspx?DisplayLang=en&FamilyID=95e24c87-8732-48d5-8689-ab826e7b8fdf .
e. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0703682EN*
Solution Usage
4
Description
eCopy™ ShareScan OP step-by-step installation instructions.
Solution
Please refer to attached install documentation for the step-by-step procedure and theeCopy™ compatible machine models, firmware and TWAIN drivers list.
To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0900736EN*
Solution Usage
4
Description
How to load a 32-bit driver on a 64-bit operating system.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
33
bizhub 360
Miscellaneous
Solution
Please follow this step-by-step procedure and refer to the attached video.
1. Load the 64-bit driver on the server and share it out.
2. Load a 32-bit driver on a workstation locally.
3. From the workstation perform the Run command to connect to the server (example: \\11.11.5.33) and press enter. This should bring up the server.
4.Navigate to the previously shared out printer on the server.
5. Right-click on the shared out printer and select properties.
6. Select the sharing tab and then click on the Additional Drivers button.
7. Select or check-off the 32-bit driver to be added to the 64-bit system.
8. Select OK and then browse to the folder that houses the 32-bit driver to be installed and select OK. The Additional Drivers window should now have the
32-bitand 64-bit checked off.
9. Check the Additional Drivers of the Server to make sure that the 32-bit has been pushed up (right-click on the shared out printer of the server
=>Properties =>Sharing Tab =>Additional Drivers).
Notes :
a.This was tested on like versions of 32-bit and 64-bit drivers.
b.To viewthis procedure, Apple© QuickTime®should be installed.It can be downloaded for free at http://www.apple.com/quicktime/download/ .
SPECIAL NOTE : Solution contribution by Freddie Burnham, Production Print/SSD
Solution ID
TAUS0651199EN*
Solution Usage
3
Description
Product Configuration Sheet.
Solution
bizhub 360/420/500 Configuration sheet . Options include:
DF-607
FK-502
FS-510/FS-511
HD-505
IC-204
JS-502
LU-201
MK-708
ML-503
MT-501
OT-501/OT-601
PC-202/PC-402
PU-501
RU-502
SC-502
SD-502
SP-501
Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Solution ID
TAUS0651550EN*
Solution Usage
3
Description
Konica Minolta Security White Paper.
Solution
See Security White Paper for details.
Notes :
a.To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
b. More in-depth security information is also availableon the Konica Minolta bizhub security page,
http://kmbs.konicaminolta.us/content/about/bizhubsecurity.html .
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
34
bizhub 360
Miscellaneous
SPECIAL NOTE : Solution contribution by Jim Behrends and Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0654802EN*
Solution Usage
3
Description
How to install Hecon® key counter.
Solution
The key counter connector is located beneath the platen glass on the right hand side of the optics section. The connector wiring must be routed to the
punch-out area at the front/right side cover.
To enable an external key counter, perform the following:
1. Enter the service mode.
2. Press [STOP], [9] on the operation panel to enter the security mode.
3. On the billing setting screen press [Management Function Choice].
4. Choose [Key Counter] to enable the plug-in key counter.
5. Press [Message] and select [Type1], [Type2], or [Type3] to determine which prompt appears on the operation panel.
6. Press [END].
7. Press [Exit].
SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/SSD
Solution ID
TAUS0656793EN*
Solution Usage
3
Solution Usage
3
Description
SMTP authentication tips.
Solution
Refer to the attacheddocument whichprovides details on how to configure the MFP to allow SMTP Authentication for Scan to E-Mail.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Rick Veale, ESS/BSE
Solution ID
TAUS0700396EN*
Description
PostScript printer PPD files for LINUX (CUPS) printing and for OpenOffice application.
Solution
The PostScript printer PPD files for LINUX environments using CUPS (Common UNIX Printing System) and for OpenOffice (Word Processor application) are
available via the Konica Minolta Download Selector:
1. Login in via www.mykonicaminolta.com .
2. Select the "Service"tab locatedat the top of the page.
3. Select the "SSD" link located on the left.
4. Select the "Continue on to the SSD Home Page" link located in the middle of the page.
5. Select the "Download MSDS, Drivers, Firmware and more" link located on the left.
6. Select Product Group, Product, File Type (Drivers) and OS (Linux).
SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS/SSD
Solution ID
TAUS0701555EN*
Solution Usage
3
Description
"Memory full" message when attempting to scan.
Solution
CAUSE: Insufficient storage space.
SOLUTION:Install the optional 40GB Hard Disk Drive, HD-505 (Item #16GA).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
35
bizhub 360
Solution ID
Miscellaneous
TAUS0801813EN*
Solution Usage
3
Solution Usage
3
Solution Usage
2
Solution Usage
2
Solution Usage
2
Description
How to convert a TIFF into a PDF when fax forwarding.
Solution
Solution:
To convert a TIFF into a PDF when fax forwarding, perform the following steps:
1. Press the Fax key.
2. Press Scan Settings.
3. Press File Type and select PDF.
4. Press the Copy button.
5. Press Utility.
6. Press Copier settings
7.Press Default settings.
8. Press Current.
Solution ID
TAUS0807951EN*
Description
How to get the number of the fax line when it is not published.
Solution
CAUSE: No cover Sheet with number or the id on machine is the name of the customer without a number.
SOLUTION: Technician can dial 1 800 444 4444, this number will provided a greeting and state the number you are calling from.
SPECIAL NOTE: Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0656733EN*
Description
Where is the touch panel adjustment located?
Solution
To access to touch screen adjustment, perform the following:
1. Select the Accessibility button.
2. Select #5 Touch Panel Adj.
SPECIAL NOTE: Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0703765EN*
Description
When attempting toload the boot file (for version 20 firmware) the file cannot be seen in the ISW Options menu.
Solution
CAUSE:Missing entry in the ISW initialization file.
SOLUTION: To enable the boot file to be loaded into the ISW utility, perform the following:
1. Using Notepad (or another text editor) open the ”ISWTrns.INI” file from the C:\Program Files\KONICA MINOLTA\ISWTrns folder.
2. In the environment setting, change [EASYTRNS_MENU_DISPLAY] from [FALSE] to [TRUE] and save the file.
3. Restart the ISWTrns tool.
4. In ISW, Select the [EasyTrnsFile (T)] dialog from the Options(O) menu.
5. Browse to the boot file.
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0800087EN*
Description
Fuser driver gears do not fit onto the existing fuser drive panel/G assembly (p/n 50GA15070F).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
36
bizhub 360
Miscellaneous
Solution
CAUSE: The drive panel has been modified and the part number for the fuser gears have been changed.
SOLUTION: Refer to attached Bulletin Number 6123 for the correct part number for the specific fuser drive gear.
Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD
Solution ID
TAUS0808178EN*
Solution Usage
2
Description
How to forward faxes to different destinations for each line with multi-line fax option.
Solution
Due to design constraints, it is not possible to forward received faxes to different destination. Both lines will forward received fax to same forwarding
destination. However, on a limited basis, it is possible to set up fax forwarding to different destinations based on TSI routing. Please refer to the User manual
for the model in question.
SPECIAL NOTE: Solution contribution by Mahen Shukla, ESS/BSE and Ian Lynch, Production Print/SSD
Solution ID
TAUS0808520EN*
Solution Usage
2
Description
Compatibility for Captaris® RightFax®.
Solution
Konica Minolta includes RightFax® compatibility as a standard feature of the MFP firmware of the supported workgroup MFPs, as well as a built-in setup
utility within the MFP PageScope Web Connection.
Konica Minolta also offers the downloadable Setup Utility for RightFax®, which provides another means of configuring the MFPs to communicate with
RightFax®. All that is required is the purchase of one Konica Minolta Connector for Captaris® RightFax® for each MFP, where RightFax® functionality is
needed. Please see attached Marketing Bulletin #08-GB-032 and Guide to the Konica Minolta Connector for Captaris® RightFax® for details. To viewa PDF,
Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Notes :
1.The links in the Guide to the Konica MinoltaConnector for Captaris® RightFax® document are "live".
2. RightFax® is now called Open Text Fax Server®since the company, Open Text©, purchased Captaris®.
Solution ID
TAUS0902606EN*
Solution Usage
2
Description
How to install a printer driver on a Macintosh® running OS 10.6.
Solution
To install a print driver on a Macintosh® running OS 10.6, there are 3possible solutions:
1. Generic : Install the printer normally and select "Generic Postscript Printer" from the "Print Using" menu.
Note : Installing the printer as a generic printer will limit the maximum paper size to legal and only allow duplexforthe finishing feature.
2. Manually install the Macintosh® OS 9 PPD file : Download the applicable OS 9 driver from the Konica Minolta website and unpack the files from the folder.
Install the printer normally and select "Other" from the "Print Using" menu. Navigate to the folder containing the OS 9 PPD file and click "Add". If the
"Installable Options" window appears, set the correct options.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
37
bizhub 360
Miscellaneous
Note : Installing the OS 9 PPD only applies to the models listed in the attached document.
3. Edit the PPD file : See the attached procedureto manually edit the PPD file. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be
downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Note : The above solutions are considered a workaround until an official OS 10.6 printer driver becomes available.
SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD
Solution ID
TAUS0603556EN*
Solution Usage
1
Solution Usage
1
Solution Usage
1
Description
Power consumption data.
Solution
Please see attachedpower consumption data for warm-up, standby, and running modes.
To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE: Solution contribution by Clinton Marquardt, ESS and Chuck Tripp, Production Print/SSD
Solution ID
TAUS0656388EN*
Description
How todisable the Protocol Trace List. The Protocol Trace List continuously prints out.
Solution
To turn off printing the Protocol Trace List, perform the following:
1. Press utilitity.
2. Press check details.
3. Press stop, 0, 0, stop, 0, 1.
4. Press Fax button.
5. Press List output button.
6. Press theOFF selection of the Protocol Trace List output.
Solution ID
TAUS0657704EN*
Description
Bates Stamping availability.
Solution
Bates Stamping is available with the firmware updateto version 20 or above.
In the Scan Mode, Bates Stamping via Annotation User Box is now available. Multiple Annotation User Boxes (up to 10) can be set up, each containing the
appropriate information required for clients or accounts.
When a document is scanned, the respective Annotation User Box is selected. When the document is printed, it will contain the date, time, text, etc. outlined
in the Annotation User Box.
The user can designate the format of the date and time, the density of the filing numbers, the text for primary and secondary fields and select the print
position of the stamp elements.
Notes :
1.The latest version firmware and system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS
Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
2.Firmware update not required for the bizhub 360 Bates Stamping function. Supported with release version of firmware.
3. The HDD option is also requiredto be able to store scanned jobs to boxwhichallows theBates Stamping function.
Solution ID
TAUS0658074EN*
Solution Usage
1
Description
CS Remote Care/vCare E-mail Setup Instructions.
Solution
Attached are the zipped CSRC E-mail Setup Instructions:
bizhub PRO 1050/1050P/1050e vCare/CS Remote Care E-mail Setup Instructions version 1.8.5
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
38
bizhub 360
Miscellaneous
bizhub 200/250/350/222/282/362 vCare/CS Remote Care E-mail Setup Instructions version 1.3.0
bizhub 360/420/500/600/750 vCare/CS Remote Care E-mail Setup Instructions version 1.2.1
bizhub PRO 920 vCare/CS Remote Care E-mail Setup Instructions version 1.8.2
bizhub C451/C550/C650/C203/C253/C353/C552/C652/361/421/501 vCare/CS Remote Care E-mail (One-Way) Setup Instructions version 1.3.0
bizhub PRO 950 vCare/CS Remote Care E-mail (One-Way) Setup Instructions version 1.3.2
bizhub C200 vCare/CS Remote Care E-mail Setup Instructions version 1.2.0
bizhub C450/C351/C250/C352/C300 CS Remote Care E-mail Setup Instructions version 1.3.8
bizhub C451/C550/C650/C203/C253/C353 vCare/CS Remote Care E-mail (Two-Way) Setup Instructions version 1.0.0
bizhub PRO C500/8050/IP-901/IP-921/IC-405/IC-302 vCare/CS Remote Care E-mail Setup Instructions version 1.8.3
bizhub PRO C6500/C6500P/C5500/C5501/C6501/C65hc/Main body NIC vCare/CS Remote Care E-mail Setup Instructions version 1.4.0
Notes :
1. To open the file WinZip® should be installed. WinZip® can be downloaded from the WinZip® website: http://www.winzip.com/ddchomea.htm . The file can
either be saved to disk or opened. It is recommended to download the ZIP and open from the local computer to view.
2.This vCare documentation can also be found by using the Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert
Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. Please see attached procedure. To view a PDF, Adobe Reader® must be installed.
Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Solution ID
TAUS0700071EN*
Solution Usage
1
Solution Usage
1
Solution Usage
1
Description
C-3501 (C3501) code at start up. Code may be intermittent and C-3801 (C3801) may also be indicated.
Solution
PROBABLE CAUSES:
1. Failed DCPS.
Note : The fuser had already been replaced, but the error code reoccurred.
Replace the DCPS (p/n 50GA 8451 0) and reset the code. To reset the code:
a. Turn ON the main power switch (SW1).
b. With the Utility/Counter key pressed, turn ON the power switch (SW2).
c. Press [Trouble reset] to release a trouble with [OK] displayed.
d. Turn OFF and ON the power switch (SW2).
2. Failed Printer Control Board orDCPS.
Replace the PRCB (p/n 50GA -902 0E) andif the problem persists, replace the DCPS (p/n 50GA 8451 0) and reset the code.
Solution ID
TAUS0702080EN*
Description
Can the TWAIN driver for scanning be utilized on a Microsoft® Windows 2003 Terminal Server?
Solution
TWAIN scanning cannot be performed in a Microsoft® Windows 2003 Terminal Server environment.
Solution ID
TAUS0702159EN*
Description
Tray 1 not lifting paper to indicate paper in the tray.
Solution
CAUSE: Failed Tray Set Sensor (PS8) for Tray 1.
SOLUTION: Replace the Tray Set Sensorfor Tray 1 (p/n 4037090601).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
39
bizhub 360
Solution ID
Miscellaneous
TAUS0702341EN*
Solution Usage
1
Solution Usage
1
Solution Usage
1
Description
J3100 code at start up. Unable to clear.
Solution
CAUSE: The torsion spring and or the actuator in the Turnover Unit are missing or damaged.
SOLUTION: Replace the torsion spring (p/n 4030381901) and or the actuator (p/n 4030381802).
Solution ID
TAUS0702445EN*
Description
How to set up FTP Publishing Services on a Microsoft® Vista™ workstation.
Solution
Please follow the step-by-step procedures as shown in the attacheddocument.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0702529EN*
Description
Howto change the paper type.
Solution
On legacy Konica Minolta copiers, paper type was set directly from the paper select menu or with a dial at the front of the paper cassette. To standardize how
this setting is made on the bizhub copiers, the setting is made in the following way:
1. Select the Utility/Counter key.
2. Select [2] User/Settings.
3. Select [1] System Settings.
4. Select [3] Paper Tray Settings.
5. Select [1] Paper Type.
6. Choose from paper trays 1 through 3 and set the paper type of the tray to either Normal, User, Recycle, Color paper, or Letterhead.
Solution ID
TAUS0702534EN*
Solution Usage
1
Solution Usage
1
Description
How to install a printer using LPR (IP Printing) under Macintosh® OS9.
Solution
Please perform the procedures mentioned in the attached document.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0702779EN*
Description
After ARPing LinkCom™ III, the LAN light still flashes and is not seen in PrintGuide™.
Solution
CAUSE: Incorrect procedure.
SOLUTION: After ARPing the LinkCom™ box, PING the TCP/IP address in order to activate the ARP. The light will go solid and it will be seen in
PrintGuide™.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
40
bizhub 360
Solution ID
Miscellaneous
TAUS0702865EN*
Solution Usage
1
Description
DF-607, misfeeding/jamming.
Solution
CAUSE: RADF feed tires not retracting to the proper position after thepaper feedcover is shut. The wire harness for the paper feed cover has moved out of
place andis putting pressure on the paper feed unit.
SOLUTION: Rewrap the wiring harness so to ensure that there is no pressure placed on the paper feed unit.
Solution ID
TAUS0703842EN*
Solution Usage
1
Description
If a print job is printed to a user box and account track is on,which account ischarged for the job when it is printed?
Solution
The account that is being used at the machine at the time of printing is charged for the print job, not the account that printed the job to the user box.
SPECIAL NOTE : Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0800173EN*
Solution Usage
1
Description
Can previous counter information be added to the counters after replacing the NVRAM?
Solution
It is not possible to addany counter information to the NVRAM if it has been replaced.The old counter information will have to be recorded elsewhereand
possibly stored inthe machine.
SPECIAL NOTE : Solution contribution by Greg Lantowski, Production Print/SSD
Solution ID
TAUS0800335EN*
Solution Usage
1
Solution Usage
1
Description
When the engine runs out of paper and is not addressed it will cause the writer on the AS/400® to stop.
Solution
CAUSE: The writer on the AS/400® times outafter 170 seconds (by default)when MFP runs out of paper.
SOLUTION: The following changes to the device description will cause the writing to ignore the time out and just report the error.
1.Pick one of the devices and end the writer and vary the device off.
2.Select the option that will allow you to 'Change Device Desc'.
3.On the first screen look for the 'Printer error message' parameter and change it to '*INFO'.
4.Page down twice and look for the 'User-defined options' parameter it should read '*IBMSHRCNN'; under thisadd ERRMSGINFO.
5.Start the writer and vary the device on and test.These changes must be done for the other device on the AS/400®.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD
Solution ID
TAUS0800403EN*
Description
How to print SAP R/3barcodes.
Solution
In order to print SAP barcodes, you need to have the barcode fonts installed on the MFP. This means that you need to purchase SAP compatible barcode
fonts and install them onto the HDD of the controller.
Currently the best andeasiestway to print SAP barcodes is to attached a device from Typehaus to the MFP.
This device has been tested and it complete compatible with SAP barcodes. This device is so sophisticated that you need not configure it with an TCP/IP
address, it will assume the TCP/IP address of the MFP and intercept the font call for the barcode and replace the call with the actual barcode fonts. Nothing
else will be required.
To Purchase this device contactTypehaus at: http://typehaus.com . Be sure to mention your affiliation with Konica Minolta.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD
Solution ID
TAUS0800946EN*
Solution Usage
1
Description
How to find/display a MAC address.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
41
bizhub 360
Miscellaneous
Solution
To find the MAC address of a specific device in a Microsoft® Windows environment, such as a main body internal NIC, access the command prompt,PING
the TCP/IP address of the device and then perform the command, arp –a .
The attached procedures are for Microsoft® Windows 98/NT/2000/2003/XP, DOS/Microsoft® Windows 3.11/Microsoft® Windows for Workgroups, Microsoft®
Windows Vista™ and Macintosh® OS X. To viewa PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe®
web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Note : Also attached is the Technitium MAC Address Changer© freeware program. This software is not supported by Konica Minolta and is to be used at
your own risk.
To open the ZIP file, WinZip® should be installed. WinZip® can be downloaded from the WinZip® website: http://www.winzip.com/ddchomea.htm . The file
can either be saved to disk or opened. It is recommended to download the ZIP and open from the local computer to view or run.
SPECIAL NOTE : Solution contribution by Cesar Jimenez and Freddie Burnham, Production Print/SSD
Solution ID
TAUS0900247EN*
Solution Usage
1
Solution Usage
1
Solution Usage
1
Description
How to change staple cartridge in saddle stitcher (SD-502).
Solution
To change staple cartridge in saddle stitcher:
1. Open front door.
2. Lift copy output tray and push down the cartridge holder and pull it out.
3. Press where it says push to unlock cartridgeholder.
4. Take out the empty staple cartridge from holder.
5. Load the new staple cartridge into the holder.
6. Carefully remove the stopper.
7. Insert the staple cartridge and push it up until it locks into place.
8. Return the copy output tray to its original position.
9. Pull the handle of the mis-feed clearing door to open it and then close it.
SPECIAL NOTE : Solution contribution by Raymond Downs, Production Customer Support/SSD
Solution ID
TAUS0901369EN*
Description
How to limit user access to copy, scan, print, user box or fax functions?
Solution
To limit user access, perform the following:
1. Press Utility/Counter key.
2. Touch Administrator Settings.
3. Select User Authentication/Account Track.
4. Touch General settings.
5. Touch User Authentication ON (MFP).
6. Are you sure you want to clear all data is shown, select YES.
7. Select User Authentication Settings.
8. Touch User Registration.
9. Select a number and input the name and password for each user.
10. Select Function Permission and set Restrict or Allow accordingly.
SPECIAL NOTE: Solution contribution by Malcolm Hibbert, Workgroup/SSD
Solution ID
TAUS0901588EN*
Description
Why SIP Fax is not working.
Solution
Attached is information designed to provide a better overview about the SIP Fax Function (FoIP - VoIP) implemented within most of the MFPs. In general,
you should find this feature on machines from 20ppm onwards providing a large graphical LCD and sold after 2001 (no line-based LCDs).
Note : To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
42
bizhub 360
Miscellaneous
SPECIAL NOTE : Solution contribution by KM Europe (BEU)
Solution ID
TAUS0902450EN*
Solution Usage
1
Description
Microsoft® Windows 7 printer drivers included with the OS.
Solution
Please refer to attached document for a list of drivers included with the Microsoft® Windows 7 operating system. To viewthe PDF, Adobe Reader® must be
installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by KMBT (Japan)
Solution ID
TAUS0902479EN*
Solution Usage
1
Description
How to set up Scan to SMB on Microsoft® Windows 2008 Server.
Solution
Please see the attached video for the procedure. The video should be played on Microsoft® Windows Media Player version 9 or later. The latest Media
Player can be downloaded at: http://www.microsoft.com/windows/windowsmedia/default.mspx .
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0629386EN*
Solution Usage
0
Description
ISO 15408 certification information.
Solution
TheMFPsare certified ISO 15408 EAL Level 3. Refer to the following for more detailed information concerning ISO 15408 as well as the attached Security
White Paper and Marketing Bulletin 09-GB-059.
1. ISO 15408 FAQ
2. Trusted Computing Base
3. ISO 15408-3
4. Common Criteria
Notes :
a. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
b. Also, go to Konica Minolta's bizhub security page, http://kmbs.konicaminolta.us/content/about/bizhubsecurity.html , for more in-depth security information.
Solution ID
TAUS0800400EN*
Solution Usage
0
Description
Preventing the write from crashing on the AS/400®.
Solution
In order to prevent the write from crashing on the AS/400® read the following IBM bulletin.
Timeout Settings in the Operating System Printer Device Description
Settings in the printer device configuration in operating system that can cause writers to end are the Inactivity timer and Activation timer.
The recommended setting for Inactivity timer should be set at some value other than *NOMAX so that the connection will be closed during periods of no
activity. Even if not sharing on the network, *NOMAX can cause problems with the writer connection.
The Activation timer should be set to a value large enough to prevent posting of intervention errors due to TCP/IP transmission delays and printer processing
delays. The default setting of 170 seconds is usually large enough to accomplish this unless you send large files to a printer with a slow processor that has a
lot of memory. Increasing the activation time will prevent unwanted intervention errors but that time will have to pass before you will get a desired intervention
error.
Note that intervention errors do not stop the print process. If the Printer Error Message parameter in the Device Description for the writer was set to *INQ ,
then the intervention will require an operator input to retry or to cancel the writer.
(At R370, the Printer Error message is not recognized on ASCII printers. Change the User defined options parameter to ERRMSGINFO ).
If the Printer Error Message parameter was set to *INFO , then the driver will continue to retry until the connection has been established or the TCP/IP has
closed the socket or, in the case of a slow printer processor, the proper response is obtained which is either the printer is on-line or that the printer has
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
43
bizhub 360
Miscellaneous
received all the data. If the connection was eventually successful, the intervention message will be attempted to be removed from the message queue, and
process will continue.
Please set the Printer Error Message to *INFO and the User Defined options to ERRMSGINFO.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD
Solution ID
TAUS0808521EN*
Solution Usage
0
Description
Captaris® RightFax® documentation.
Solution
Please see attached Captaris® RightFax® documentation for reference. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be
downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
The documentation includes:
Guide to the Konica Minolta Connector for Captaris® RightFax®
Setup Utility for Captaris® RightFax® - User's Guide
Operations for Captaris® RightFax® - User's Guide
Captaris® RightFax® Solutions with Konica Minolta white paper
Notes :
1.The links in the Guide to the Konica MinoltaConnector for Captaris® RightFax® documentare "live".
2. RightFax® is now called Open Text Fax Server®since the company, Open Text©, purchased Captaris®.
Solution ID
TAUS0701073EN*
Solution Usage
Description
What other unit is neededwhen installing the FS-511?
Solution
The RU-502 (Relay Unit) is required when installing the FS-511 to the bizhub 360/420/500.
Solution ID
TAUS0701136GE*
Solution Usage
Description
Are Citrix© certified drivers available?
Solution
Citrix© certified drivers are not available.
SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0701331EN*
Solution Usage
Description
What is required to install the two-line fax kit ML-503?
Solution
The ML-503 Fax Multi-Line Kit includes the FK-502 and ML-503.
Notes :
1. Attachedare the configurationsheets for the MFP. They illustrate what options are required when configuring the bizhub 360/420/500 and bizhub
361/421/501.
2. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by John Miller, Workgroup/SSD
Solution ID
TAUS0701343EN*
Solution Usage
Description
The FK-502 and the fax option is not being seen by the copier.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
44
bizhub 360
Miscellaneous
Solution
CAUSE:ADIPSW setting is required for enabling fax support on the bizhub 360/420/500 copiers. There is an isolation switch for the fax option. DIPSW 19, bit
1 will be enabled in the event a service issue with the fax goes not cleared. Set DIPSW 19, bit 1 to the OFF position if the fax option becomes invisible to the
copier.
SOLUTION: Set DipSW 19, bit 1 to the OFF setting by the following procedure:
1. "Service Mode screen" Press [System 2].
2. "System Input screen" Press [DipSW Setting].
3. "Software Switch Setting screen" Press [SW No.].
4. Press the [+]/[–] or numeric keys to enter the DipSW No. In "SW Setting value", 8-bit data of the DipSW number selected is displayed in binary digit and
hexadecimal digit.
5. Press [Bit No.].
6. Press the [+]/[–] or numeric keys to enter the bit number.
7. Press either of [OFF (0)] or [ON (1)] of "Bit Data" to set a value.
8. Press [Set].
9. Repeat steps 3 to 8 to set necessary software DipSW.
10. Press [OK].
Solution ID
TAUS0701441EN*
Solution Usage
Description
What is the maximum monthly copy/print volume?
Solution
The maximum monthly volume is 150,000 copies/prints for the bizhub 360/420 and 175,000 for the bizhub 500.
SPECIAL NOTE : Solution contribution by Mike Galletta, Workgroup/SSD
Solution ID
TAUS0701637EN*
Solution Usage
Description
What is the proceesor speed of the IC-204?
Solution
The processor speed is 400MHz.
SPECIAL NOTE : Solution contribution by Mike Galletta, Workgroup/SSD
Solution ID
TAUS0701638EN*
Solution Usage
Description
What operating systems are supported for printing via the IC-204?
Solution
The IC-204 supports Microsoft® Windows 98SE/ME/NT 4.0 SP6/2000/XP/Server 2003/Vista™, Macintosh® OS 9.2 - Macintosh® OS X 10.5 (PPD files) and
LINUX.
SPECIAL NOTE : Solution contribution by Mike Galletta, Workgroup/SSD
Solution ID
TAUS0701655EN*
Solution Usage
Description
What is the maximum print resolution?
Solution
The maximum print resolution is 600x600 dpi.
SPECIAL NOTE : Solution contribution by Mike Galletta, Workgroup/SSD
Solution ID
TAUS0701656EN*
Solution Usage
Description
What is the maximum size copy that can be made? Will the machine copy 12x18 size paper?
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
45
bizhub 360
Miscellaneous
Solution
The maximum copy size is 11x17. These model machines will not copy 12x18 size paper.
SPECIAL NOTE : Solution contribution by Mike Galletta, Workgroup/SSD
Solution ID
TAUS0702306EN*
Solution Usage
Description
How to increase the fuser temperature by 10 degrees C.
Solution
To increase/decrease the fuser temperature, perform the following:
1. Press the Utility button and select details.
2. Enter the service mode (stop, 0, 0, stop, 0, 1).
3. Select System 2.
4. Select DipSW Settings.
5. Change switch 36, bit 2and switch 36, bit 3 tothe desired setting (see chart below).
6. Cycle power OFF/ON.
Mode
36-3
36-2
Standard
0
0
Standard + 10 °C
0
1
Standard + 5 °C
1
0
Standard – 10 °C
1
1
Note : To viewthe attachedPDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0702313EN*
Solution Usage
Description
How to reset afuser code.
Solution
To reset a fuser code, perform the following:
1. TurnOFF the main power switch.
2. Press and hold the utility button.
3. Turn the main powerON switch while holding down the utility button.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
46
bizhub 360
Miscellaneous
4. When Troublereset button appears, press it and cycle power OFF/ON.
Solution ID
TAUS0702579EN*
Solution Usage
Description
ICP list.
Solution
Please review the attached document.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0702694EN*
Solution Usage
Description
What is the difference between the “Number of Originals” and the “Number of Prints”?
Solution
The service documentation is a little unclear.
The “Number of Originals” corresponds to the number of faces that are produced and the “Number of Prints” isthe quantity of sheets fed.
For example, if a two-sided original isfed and 5 copies are selected,the counters wouldindicate "10"for the amount of originals and "5" for the number of
prints.
Solution ID
TAUS0702889EN*
Solution Usage
Description
Printing to a printer on a Microsoft® Windows XP PC from a Macintosh® OS version 10.3.
Solution
Please perfrom the step-by-step procedures mentioned in the attached PDF.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Cesar Jimenez and Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0703363EN*
Solution Usage
Description
Can PageScope Data Administrator export user boxes to another unit?
Solution
PageScope Data Administrator cannot export user boxes to another unit.
Note : At this present time, there is no application or utility, except for the HDD Backup utility, which takes hours to complete the backup.
SPECIAL NOTE : Solution contribution by Malcolm Hibbert, Workgroup/SSD and Ian Lynch, Production Print/SSD
Solution ID
TAUS0703426EN*
Solution Usage
Description
Can the output capacity be changed when a finisher job tray is not connected?Only400 sheets are output.
Solution
CAUSE: Incorrect settings.
SOLUTION: Service soft switch, DipSW 15, bit 6 can be set to ON. This will change the Stop/non-stop due to overload when not connected to Finisher/job
tray. By default this capacity is set to 400 sheets. When enabled there is no limit.
Note : The output must be monitored since there is no limit when enabled.
To access the DIPSW setting mode, perform the following:
1. "Service Mode screen"; press [System 2].
2. "System Input screen"; press [DipSW Setting].
3. "Software Switch Setting screen"; press [SW No.].
4. Press the [+]/[–] or numeric keys to enter the DipSW No. (DipSW15). In "SW Setting value", 8-bit data of the DipSW number selected is displayed in binary
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
47
bizhub 360
Miscellaneous
digit and hexadecimal digit.
5. Press [Bit No.].
6. Press the [+]/[–] or numeric keys to enter the bit number (Bit 6).
7. Press either[OFF (0)] or [ON (1)] of "Bit Data" to set a value.
8. Press [Set].
9. Repeat steps 3 to 8 to set necessary software DipSW.
10. Press [OK].
SPECIAL NOTE : Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0703635EN*
Solution Usage
Description
Is a connection/adapter harness available for the optional key counter?
Solution
There is a 4- pin female connection. The first pair of wires has a jumper for the set signal. The second pair triggers the counter and is based on a 24V DC
circuit which is standard. This is a standard configuration for most vendors on the market.
Please check withthe external vendor/counter manufacturer before replacing any harness. There maybe an adapter of their own available.
Note : Some vendors require a white four-pin female connection. An adapter is available in this case (p/n 1206K0010).
SPECIAL NOTE : Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0800433EN*
Solution Usage
Description
IsMagneCote® paper or magnetic backed paper supported?
Solution
MagneCote® paperor magnetic backed paper is not supported.
SPECIAL NOTE : Solution contribution by Marge McLea, ProductionCustomer Support/SSD
Solution ID
TAUS0800558EN*
Solution Usage
Description
DF-607, part number for the Upper Mylar.
Solution
Upper Mylar (p/n 4344 PP03 00). It is listed as item 27 on page 4 in the version 3 DF-607PC Parts Manual. It is not listed in previous versions.
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Solution ID
TAUS0800608EN*
Solution Usage
Description
Additional information concerning "Custom Size Settings".
Solution
In the Konica Minolta PCL driver, the "Custom Size Settings" can only be specified from the printer driver setup dialog box, which can be displayed from the
"Printers" window (or "Printers and Faxes" window).
Please refer to attached documentation for clarification. To viewthe PDFs, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free
from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0800611EN*
Solution Usage
Description
Additional information concerning PageScope Web Connection.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
48
bizhub 360
Miscellaneous
Solution
Additional information for bizhub PRO 920/IC-203 and bizhub PRO 1050 series/IC unit:
1. "Done Job List" maximum number.
Maximum is 100 ([Print] and [Scan transmission]). If it exceeds 100, the jobs are deleted from old history.
2. Please note that "Done Job List" is all deleted when the main body poweris turned OFF.
Note : Please refer to attached documentation for clarification. To viewthe PDFs, Adobe Reader® must be installed. Adobe Reader® can be downloaded
for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Additional information for bizhub 360/420/500/IC-204 and bizhub 600/750/IC-202
1. "Job History" maximum number.
Maximum is 100 in all jobs ([Print], [Scan], [Fax TX], [Fax RX] and [HDD/Memory]) total.
2. "Job History" display/non-display setting (after main body poweris cycled OFF/ON).
Even if main body power is cycled OFF/ON, "Job History" is not usually deleted. However "Job History" can be set to non-display (data is deleted)by DipSW
24-1.
DipSw 24-1
0: Display
1: Non-display
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0800844EN*
Solution Usage
Description
Problem:
Is the Image Controller (IC-204) required for scanning to SMB?
Solution
Solution:
The Image Controller is NOT required for scanning to SMB.
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0800925EN*
Solution Usage
Description
How to set up FK-502 for transmit only.
Solution
Specify "Manual Reception" in line parameter setting in Admin. Mode. This way, if there is no external phone connected, the fax will not be received by the
MFP.
SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/SSD
Solution ID
TAUS0800971EN*
Solution Usage
Description
HDD Backup Utility User's Guide.
Solution
Main features covered:
Backing up (saving)
Restoring (recovering)
Wizard operations (program in dialog format)
Access limitations through auto protect
Encoding backup data
Please refer to the attached documentation. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the
Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
49
bizhub 360
Solution ID
Miscellaneous
TAUS0801073EN*
Solution Usage
Description
How to change the date and time on the controller.
Solution
To change the date and time on the controller:
1. Utility Counter.
2. Administrator Settings.
3. System Settings.
4. Date and Time.
5. Select whatneeds to be changed (Year, Month, Day, Hour, Minute or Time Zone).
6. Select the C on the control panel.
7. Make the change using the numbered keypad.
8. When all the changes have been made, select OK.
SPECIAL NOTE : Solution contribution by Marge McLea, Production Customer Support/SSD
Solution ID
TAUS0801081EN*
Solution Usage
Description
Serial number and meter reading locations.
Solution
Serial Number: Open paper Tray 1. Located on UPC sticker on main body.
Meter: Open right front door. Meter is below power switch.
Note : Please see attachment as a reference.
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD and Bill Hall, Workgroup/SSD
Solution ID
TAUS0801122EN*
Solution Usage
Description
What are the maximum E-Mail one-touch destinations?
Solution
Maximum E-Mail one-touch destinations:
Model
Destinations (max)
Comments
7272
1008
bizhub 600/750
600
bizhub 500/420/360
1000
2000 w/HDD
bizhub 200/250/350
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
50
bizhub 360
Miscellaneous
549
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0801303EN*
Solution Usage
Description
How to add or change TCP/IP address to printer.
Solution
To add or change TCP/IP address to printer:
1. Utility/Counter.
2. Administrator Setting.
3. Enter Password (12345678).
4. Network Settings.
5. TCP/IP Settings.
6. ON.
7. Fwd Key (at top of screen).
8. Manual.
9. IP Address.
10. Change or add TCP/IP address using key pad.
11. OK/Close/Close.
SPECIAL NOTE : Solution contribution by Marge McLea, Production Customer Support/SSD
Solution ID
TAUS0801335EN*
Solution Usage
Description
After changing toner, the toner door will not close properly.
Solution
CAUSE: Incorrect toner bottle installation.
SOLUTION: Take out the toner bottle and check the housing ring in whichthe toner bottle slides. It has 3 notches that should be in the 12 o'clock position.
Ifnot, spin the ring to the 12 o'clock position. Insert toner bottle with arrow on the bottle at the 12 o'clock position.
SPECIAL NOTE : Solution contribution by Marge McLea, Production Customer Support/SSD
Solution ID
TAUS0801362EN*
Solution Usage
Description
ISIS scan support.
Solution
Driver support for ISIS scanning is not available. Thisappliesto all Konica Minolta devices, B/W MFPsand Color MFPs.
The TWAINscanner I/F standard is supported.Scannerapplications can support the TWAIN driver.
The latestproductssupport OpenAPI whichcan expand scanner functions and connectivity to applications.
Note : ISIS isa scanner interface standard defined by EMC Captiva. Please refer to http://en.wikipedia.org/wiki/ISIS for more details.
SPECIAL NOTE : Solution contribution by KM Europe (BEU).
Solution ID
TAUS0801567EN*
Solution Usage
Description
Office Workgroup and Production Print - Basic Functionality Chart (Marketing Bulletin 08_GB_024).
Solution
Konica Minolta is pleased to announce a new sales tool called the Office Workgroup and Production Print - Basic Functionality Chart (see attachment). This
chart has been developed to give you a broad overview of the basic functionality on all current Office Workgroup MFPs and Production Print Systems.
This ‘at-a-glance’ chart will be helpful to determine product families, standard and optional features, print and scan PPM speeds, copy, print controller, local
and network scanning destinations and lastly fax functionality.
Models associated with the chart are: bizhub 160, 161f, 181, 200, C203, 250, C253, 350, C353, C353P, 360, 421, C451, 501, C550, 600, C650, 750 and
bizhub PRO C5500, C6500, 920, 1050e.
This chart will be associated under Support Materials or individual product pages for each model listed on MyKonicaMinolta.com.
Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
51
bizhub 360
Solution ID
Miscellaneous
TAUS0801690EN*
Solution Usage
Description
Is another MK-708 mount kit required when configuring dual line capability?
Solution
The MK-708 should already be installed if the machine has the FK-502 installed.Another MK-708 is not required, but, for dual line capability, the ML-503 kit
(Item #7640X024)should be installed. Please refer to attached Installation Manuals for additional information. To view a PDF, Adobe Reader® must be
installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Notes :
1. The multi-line kit (ML-503) come with another fax board (FK-502).
2. When the Fax kit is installed in a machine on which CS Remote Care setting is set as “FAX”, the FAX-CSRC function allows the host to access all the data
in the machine by default. Be sure to explain the above as well as FAX-CSRC functions to users before installing the Fax kit and get their consent.
SPECIAL NOTE : Solution contribution by Mike Galletta, Workgroup/SSD
Solution ID
TAUS0801738EN*
Solution Usage
Description
FK-502, subject change for fax forwarding.
Solution
When forwarding to E-mail, the subject format can be selectedasfollows for Image Receiver Software.
Soft Switch number 28 =00 (hex)
FWD:[ @@@ ] :FAX image from [ **** :yyyy/mm/dd]
Note : @@@ represents the sender name registered in the MFP forwarding the fax job. When nothing is registered as the sender,subject of the E-mail
will be blank.
**** represents the information of the fax sender.
SPECIAL NOTE : Solution contribution by Freddie Burnham and Ian Lynch, Production Print/SSD
Solution ID
TAUS0801746EN*
Solution Usage
Description
MSDS information.
Solution
See attachmentfor MSDS information.
Note : To open the file(s) using WinZip®, WinZip® must be installed. WinZip® can be downloaded from the WinZip® website:
http://www.winzip.com/ddchomea.htm .The file can either be saved to disk or opened.It is recommended to download the ZIP and open from the local
computer to view.
To view thezipped PDF(s), Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Solution ID
TAUS0801949EN*
Solution Usage
Description
When scanning to FTP, can the machine print out a confirmation report?
Solution
The machine cannot print out a confirmation report for scan to FTP.
SPECIAL NOTE : Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0801975EN*
Solution Usage
Description
How to default the machine back to 1:1 duplex mode. It is currently defaulted to 1:2.
Solution
CAUSE: Improper machine programming. This kind of issue can happen after flashing a machine or accidentally caused by the end user.
SOLUTION: Please reset the control panel back to factory defaults:
1.Press the Utility key.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
52
bizhub 360
Miscellaneous
2.Touch User Setting.
3.Touch Initial Setting.
4.Touch Factory default.
5.Touch OK and exit the mode.
SPECIAL NOTE : Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0802054EN*
Solution Usage
Description
SP-501 installation instructions.
Solution
Please refer to the attached SP-501 (Stamp Unit) Installation Manual. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be
downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Solution ID
TAUS0802099EN*
Solution Usage
Description
When the dual line kit (ML-503)is installed, can each line be set to send a different header automatically?
Solution
When the dual line kit is installed each line cannot be set to send a different header automatically. If the header needs to be changed it must be selected at
the time of the transmission.
SPECIAL NOTE : Solution contribution by Dave Bruni, Workgroup/SSD
Solution ID
TAUS0802165EN*
Solution Usage
Description
How to change the staple cartridge.
Solution
To change the staple cartridge:
1. Open front door.
2. Below FN5 and FN6 you will see a white and green gear.
3. Turn the green gear counterclockwise and that will move the staple unit to the front of the machine.
4. When the staple unit is all the way to the front, pull the green tab to the cartridge unit and it will release it.
5. Pull it out and replace the cartridge unit with a new one.
Refer to the attached PDF for illustrated instructios for the FS-510, FS-511, and SD-502.
Note: To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
SPECIAL NOTE: Solution contribution by Marge McLea, Production Customer Support/SSD
Solution ID
TAUS0802271EN*
Solution Usage
Description
Is a local interface available for the bizhub 360/420/500 series?
Solution
Printing is supported only via Ethernet (network) connection on these models.
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0802510EN*
Solution Usage
Description
How toprint the TX report.
Solution
To print the TX report, follow these steps:
Press the Administrator Settings key.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
53
bizhub 360
Miscellaneous
Enter the password (12345678).
Select Fax Settings.
Select Report Settings.
Check TX Report Results (if set to ON, it will print after every transmission).
Also, please refer to the attached file.To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web
site at: http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE: Solution contribution by Marge McLea, Production Customer Support/SSD
Solution ID
TAUS0802560EN*
Solution Usage
Description
How to reprogram the total counters now that the NVRAM has been replaced. The counters do not match the machine actual counts.
Solution
The counters can not be reprogrammed. Please track the counts from the current count onward.
SPECIAL NOTE : Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0808228EN*
Solution Usage
Description
How to enable/disable Tray 1.
Solution
To enable/disable Tray 1, perform the following:
1. Press the Utility/Counter key.
2. Touch [Details] on the touchscreen.
3. Press Stop-0-0-Stop-0-1.
4. Touch [System 1] on the touchscreen.
5. Touch [Trouble Isolation] on the touchscreen. Tray 1 will be displayed on the touchscreen.
6. Touch [SET] or [UNSET] on the touchscreen.
7. Touch [END] on the touchscreen.
8. Touch [Exit] on the touchscreen.
SPECIAL NOTE : Solution contribution by Ted Young, Production Print/SSD
Solution ID
TAUS0808229EN*
Solution Usage
Description
How to enable/disable the HDD.
Solution
To enable/disable the HDD, perform the following:
1. Press the Utility/Counter key.
2. Touch [Details] on the touchscreen.
3. Press Stop-0-0-Stop-0-1.
4. Touch [System 1] on the touchscreen.
5. Touch [Trouble Isolation] on the touchscreen.
6. Touch [2] on the touchscreen. HDD will be displayed on the touchscreen.
7. Touch [SET] or [UNSET] on the touchscreen.
8. Touch [END] on the touchscreen.
9. Touch [Exit] on the touchscreen.
SPECIAL NOTE : Solution contribution by Ted Young, Production Print/SSD
Solution ID
TAUS0808640EN*
Solution Usage
Description
Location of hole punch scraps box.“Remove Punch Scraps” message may be indicated (PU-501).
Solution
Open the finisher (FS-510/FS-511)door and remove and empty the scraps box (dust box). Please refer to attached instructions. To viewthe PDF, Adobe
Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Marge McLea, Production Customer Support/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
54
bizhub 360
Solution ID
Miscellaneous
TAUS0900083EN*
Solution Usage
Description
How to default the opening scan size of a scanned document from Adobe® Acrobat® 7/8/9.
Solution
To default the opening scan size of a scanned document via Adobe® Acrobat® 7/8/9 perform the following:
1.Open a PDF.
2.Select Edit and then Preferences (see attached photo).
3.Click on Page Display => Magnification. Zoom to Scroll and select the desired opening size.
SPECIAL NOTE : Solution contribution by Mark D'Attilio/Ian Lynch/Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0900084EN*
Solution Usage
Description
Problem:
This Mode can not be set with offset.
The bypass has been selected and it is currently configured for envelop printing.
The finisher is defaulted for offset sorting.
Solution
Cause:
Incompatible machine functions.
Solution:
Disable the offset option for the finisher.
Select the finishing button at the ready screen.
Touch the offset button to unselect it.
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0900311EN*
Solution Usage
Description
How to pre-program a 9 for the PBX system.
Solution
Topre-program a 9 for the PBX system, perform the following:
1. Enter the Admin Mode
2. Select Fax Setting.
3. Touch PBX CN Set.
4. Touch PBX CN Mode Set to ON.
5. Press the "C" key and enter 9 and press OK.
6. Press close three times to exit.
SPECIAL NOTE: Solution contribution by Malcolm Hibbert, Workgroup/SSD
Solution ID
TAUS0900368EN*
Solution Usage
Description
How to set the machine to accept another copy job while the previous job is printing, without having to use the next job reservation feature.
Solution
To enable the user to reserve a copy job without using next job reservation, perform the following:
1. Press the Utility key.
2. Select User Setting.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
55
bizhub 360
Miscellaneous
3. Select Display Setting.
4. Select Copy Screen.
5. Set Copy Operating Screen to OFF.
6. Exit the User Setting mode.
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0901085EN*
Solution Usage
Description
What load check mode can be used to turn the toner bottle?
Solution
Please use code 56 with multi code 1 to turn the toner bottle clock wise. Please use code 56 with multi code 2 to turn the toner bottle counter clock wise.
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0901278EN*
Solution Usage
Description
Why is the TX Stamp not applied to the original when a fax is sent, the operation of the stamp has been confirmed in state confirmation?
Solution
The TX Stamp will not be applied to the original when a fax is sent if mixed original has been selected. Please unset mixed original detection prior to
choosing the stamp function.
SPECIAL NOTE: Solution contribution by Dave Bruni, Workgroup/SSD
Solution ID
TAUS0901466EN*
Solution Usage
Description
What is the recommended MD5 checker?
Solution
Therecommended MD5 checker is HkSFV (download attached file).
HkSFV uses CRC-32 and MD5 technology to validate the integrity of files that you have downloaded or moved through a potentially unstable medium (burnt
to CD, transferred over the Internet/LAN). HkSFV can verify your files in seconds and is compatible with Win-SFV and md5sum.
HkSFV is the simple, easy and most automatic application to create or check SFV and MD5 files.
What is an SFV?
An SFV file is a tiny list of files and CRCs, which allow you to check to see if the files you have downloaded are exactly what you are expecting. The CRC
algorithm used in SFV files allows you to see if the file you have has been changed, even a single byte, since the SFV file was created.
What is an MD5?
MD5 did not exist until somewhat recently, as md5sum is a popular UNIX format similar to SFV and UNIX does not use file extensions the way Microsoft®
Windows-based systems do. MD5 uses the md5 algorithm to computechecksums, rather than the CRC-32method used by SFV. The md5 algorithm is almost
as fast as CRC-32, but it is much more accurate at detecting changes in files.
Some key features of HkSFV:
Easy installation and automatic uninstallation (leaves no trace in the registry, even goes one step further than most programs and restores previous file
associations when you remove it)
One-click creation and checking of SFVs and MD5s
Flawless & smooth upgrading to new versions (simply install the new version)
Automatic association with SFV files, and an option to fix file association when other programs steal it
Handles SFV and MD5 files from any other program invisibly (including files created on *NIX)
Database/cache of previously checked files
Batch SFV and MD5 checking - queue up and check many SFVs and MD5s in one pass, specify a directory and check all the SFVs and MD5s in that
directory (including subdirectories, if you want)
Automatically find renamed files while checking SFV or MD5 files
Enqueue SFVs or MD5s during file verification
Recursive directory support during creation and verification
Supports creation of .bad and .missing files, or deleting failed files
Drag-and-drop SFV or MD5 file or directory to create/check SFV or MD5
SPECIAL NOTE : Solution contribution by Gregg Gallant, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
56
bizhub 360
Solution ID
Miscellaneous
TAUS0901575EN*
Solution Usage
Description
How to print booklets for MicroSoft Publisher 2003 onto legal size paper using a Windows driver.
Solution
To print booklets from MicroSoft Publisher 2003 perform the following:
In Publisher before creating the document:
1. Select File > page setup and under the layout tab select Full Page.
2. Under the Printer and Paper tab select a page size of 5.5 X 8.5 and save.
3. This will create a booklet that does not scale. If the booklet was already created image size may need to be adjusted on each page.
When printing perform the following:
1. Select File > Print and then select the printer properties.
2. On the basic tab select the paper size as 8.5 by 14.
3. On the layout tab select booklet.
4. On the finishing tab select center staple and fold.
5. Click OK and print.
SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD
Solution ID
TAUS0901684EN*
Solution Usage
Description
Konica Minolta universal PostScript/PCL printer drivers.
Solution
The first versions of the universal PostScript/PCL printer drivers are available. Theseprinter drivers offer customers the benefit of a simplified management for
IT administrators and a powerful print driver for user utilizing multiple printers.
The concept is to offer a single universal PostScript/PCL printer driver that is available for Konica Minolta MFPs and printers and that is also compatible with
other brands of PCL/PostScript printers. This creates a common user interface across all printers and automatically detects printers on the network for easy
configuration.
Please refer to attached Marketing Bulletin #09-GB-017 for more detail. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be
downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Solution ID
TAUS0902269EN*
Solution Usage
Description
How to setup the machine to use and recognize both A4 and 8.5 X 11 from both the platen and document feeder.
Solution
To setup a machine to use recognize A4 and letter originals perform the following:
1.Enter the Service mode.
2.Select System 1.
3.Select Original Size Detection.
4.Change Original Glass Original Size Detect from "Inch Series" to "Full Size."
5.Change Original ADF Original Size Detect from "Inch Series to Full Size."
6.In Admin Mode go to copier settings and set both Platen AMS and ADF AMS to on.
7.Have the copier defaulted to Auto paper.
8.If the ADF does not properly recognize the sizes perform the ADF original size adjustment in service mode.
SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD
Solution ID
TAUS0902314EN*
Solution Usage
Description
How to format the HDD.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
57
bizhub 360
Miscellaneous
Solution
To format the HDD, perform the following:
1. Press the Utility/Counter key.
2. Touch [3 Administrator Settings] on the touchscreen.
3. Input the Administrator Password (default password is 12345678).
4. Touch [OK] on the touchscreen.
5. Touch [9 Security Settings] on the touchscreen (or [0 Security Settings] for bizhub 360/420/500).
6. Touch [6 HDD Settings] on the touchscreen.
7. Touch [5 Format HDD] on the touchscreen.
8. Touch [Yes] on the touchscreen.
9. Touch [OK] on the touchscreen.
10. Press the Reset key to return to the normal screen.
CAUTION : Please be aware that the following datais deleted/erased when the hard disk is formatted.
Program address
Address Book
Authentication method settings
User authentication settings
Account track settings
User boxes
User box settings
Documents in user boxes
Secure print user box settings
Bulletin board user box settings
Note : Please refer to attached documentation for more detail. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for
free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Ted Young, Production Print/SSD
Solution ID
TAUS0902480EN*
Solution Usage
Description
How to set up Scan to FTP on Microsoft® Windows 2008 Server.
Solution
Please see the attached video for the procedure. The video should be played on Microsoft® Windows Media Player version 9 or later. The latest Media
Player can be downloaded at: http://www.microsoft.com/windows/windowsmedia/default.mspx .
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0902510EN*
Solution Usage
Description
What can cause the machine to display a C-1118 code?
Solution
The machine may display a C-1118 code if the one-way gearsin the exit section have failed. Please replace the one-way gears (p/n 4349-1633-01) and (p/n
4349-1611-01) to correct the code.
SPECIAL NOTE: Solution contribution by Dave Bruni, Workgroup/SSD
Solution ID
TAUS0902637EN*
Solution Usage
Description
Paper Feed Cabinet motor and board change.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
58
bizhub 360
Miscellaneous
Solution
Due to a change in suppliers, the motor used in the models listedhas been changed. In order to keep the performance the same as with the older motors, the
related PWB was also changed.
PC-101
PC-102
PC-103
PC-104
PC-201
PC-202
PC-203
PC-204
PC-206
PC-402
PC-403
PC-405
PC-407
PF-122
PF-124
PF-210
Note :Original and modifiedparts are not to be mixed. Boards and motors must be replaced as a set (both must be either original style or modified style).
Please see attached Bulletin Niumber 6703 for additional information and part numbers. To viewthe PDF, Adobe Reader® must be installed. Adobe Reader®
can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
59
bizhub 360
Solution ID
Original jam, no-feed, multi-feed, folding, tearing, skewing, curling
TAUS0802436EN*
Solution Usage
Description
DF-607, J-6501 that may clear by lifting and closing the document feeder.
Solution
PROBABLE CAUSES:
1.The DF-607 may be misaligned.
Adjust postion of DF-607 using the alignment screws on the hinges.
2.PS6 is misaligned or has failed.
Adjust position/replace PS6 (p/n 4344 5167 02).
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Solution ID
TAUS0901876EN*
Solution Usage
Description
PC402, intermittent J-1305 codes.
Solution
CAUSE: The 1-way clutch for the tray 3 feed rollers is dirty or has failed.
SOLUTION: Clean the 1-way clutch for the tray 3 feed rollers (p/n 4030 3034 01). If necessary, replace the tray 3 1-way clutch.
SPECIAL NOTE: Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0902155EN*
Solution Usage
Description
J-7221 code when stapling or sorting.
Solution
CAUSE: Finisher exit roller one way gear has failed.
SOLUTION: Replace the finisher exit roller one way gear (p/n 4349 1633 01).
SPECIAL NOTE: Solution contribution by Tom Kelly, Workgroup/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
60
bizhub 360
Solution ID
Paper Conveyance jams, no-feed, folding, tearing, skewing, curling
TAUS0700176EN*
Solution Usage
12
Description
J-3000 jam code. May occur onlywhen duplexing.
Solution
PROBABLE CAUSES:
1.Shorted Toner Solenoid (SD5).
Note : CL1 fails and CL2operates properly.
Check for a short at SD5 (p/n 26NA 8251 3).If along screw was substituted for ashort oneit could contact thewindings of the solenoid.Replace SD5 as
necessary along with PRCB (p/n 50GA -902 0E)
2. Failed main board.
Checkthe following:
a. PS1 in IO mode (p/n 13QA 8552 1)
b. CL1 (p/n 57AA 8203 0) and CL2(p/n 50GA 8202 0) in IO mode
IftheCL1 fails and CL2checks OK,check the Main Control Board for missing 24V DCon connector CN22-B5.Check for an open ICP4. If no voltage or a very
low voltage is present, and ICP4 is OPEN,replace the Main CB (p/n 50GA -902 0E) after checking for short at the toner solenoid (p/n 26NA 8251 3).
3. Failed CL7 and or CL8.
Please replace the ADU clutches, CL7 and CL8 (p/n 50GA 8203 0).
Note : Both clutcheshave the same part number.
4. Guide sheet in the multi-bypass tray malformed or damaged.
Please replace the guide sheet in the multi-bypass tray with the modified guide sheet. For more information please see the attached Parts Modification
Notices. To viewa PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE: Solution provided by Jeff Rings, Mason City Business Systems and David Silverstein/James Behrends, Workgroup/SSD
Solution ID
TAUS0801765EN*
Solution Usage
8
Solution Usage
6
Description
FS-xxx, first page not aligned properly/not stapled in stapled sets.
Solution
CAUSE:Static build-up onalignment plate which causes the first page to stick.
SOLUTION:Wipe affected are with anti-static compound (Brillianize®, Pledge®, dryer sheet, etc.).
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Solution ID
TAUS0703395EN*
Description
Intermittent jamming/misfeeding from paper cassette(s).
Solution
CAUSE: Paper cassettemoves forward due tomachine vibration. The cassette holder is worn/weak and t he "holding power" hasdecreasedover time.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
61
bizhub 360
Paper Conveyance jams, no-feed, folding, tearing, skewing, curling
SOLUTION: The shape of holder has been changed, strengthening the power of cassette hold and by installing a Stop Ring (p/n 4348620600).
Install thecassette holdercountermeasure to preventthe cassette from unlockingas explained inattached Bulletin Number 6217.To viewa PDF, Adobe
Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Solution ID
TAUS0800187EN*
Solution Usage
2
Description
Jamming in registration area when duplexing (various J-codes may be indicated).
Solution
CAUSE: ADUloop clutch failure. If there is repeated jamming in the registration area, often when duplexing, the clutch (CL3) in the vertical conveyance
(behind the bypass feed area)may bethe cause.
SOLUTION: Please replaceCL3 (p/n 50GA 8202 0).
SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/BSE
Solution ID
TAUS0901175EN*
Solution Usage
1
Solution Usage
0
Description
How to display the jam counters?
Solution
To display the jam counter perform the following:
1. Enter the Service mode.
2. Select Counter.
3. Touch Jam.
4. Scroll through 1 of 16 pages to find the jam codes.
SPECIAL NOTE: Solution contribution by Malcolm Hibbert, Workgroup/SSD
Solution ID
TAUS0802648EN*
Description
"Now Warming" displays if the machine is turned on with the right door open. When the door is then closed "Warming Up" stays on the screen. The fuser is
warm. If all doors are closed at startup, C-6702 appears, but before this code shows up, the machine asks to close the covers, and then goes into the C-6702
code.
Solution
CAUSE: 2000 sheet LCT connections wires in connector are loose.
SOLUTION: Resolder connector wires or replace harness (p/n 4348 6801 02).
SPECIAL NOTE: Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0802037EN*
Solution Usage
Description
Fuser jams.
Solution
CAUSE: Rocking Collar (p/n 1200210502) becomes loose or dislodges.
SOLUTION: Replace the current part with the modified Separate Rocking Collar (p/n 1134304101). Please refer to attached Bulletin Number 6429 for details.
To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
62
bizhub 360
Solution ID
Paper Conveyance jams, no-feed, folding, tearing, skewing, curling
TAUS0802846EN*
Solution Usage
Description
Paper skews when feeding from the PC-402.
Solution
CAUSE: The latches on the PC-402 door might be worn.
SOLUTION: Replace the latches for the PC-402 door. The part numbers are 15EK 1212 0 and 15EK 1213 0.
SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD
Solution ID
TAUS0808283EN*
Solution Usage
Description
PROBLEM:
Stacker tray is not rising to the exit area while making copies/prints and removing stack (FS-511).
Solution
CAUSE:
This a product limitation
SOLUTION:
Advise customer not to remove the stack until a message states to remove itor when thejob finishes.
SPECIAL NOTE: Solution contribution by Don St. Onge, Workgroup/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
63
bizhub 360
Solution ID
Software/Driver related
TAUS0607358EN*
Solution Usage
22
Description
The entire print job is stapled instead of each set when printing multiple stapled sets from Microsoft® Word.
Solution
CAUSE:The Collate option in the Microsoft® Word dialog box is selected.
SOLUTION:When printing and stapling multiple sets, the Collate option in the Microsoft® Word dialog box must be deselected. Please refer to attached
example. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution byMark D'Attilio and Ed Bellone, Production Print/SSD
Solution ID
TAUS0701860EN*
Solution Usage
13
Description
HTTP 400 - Bad Request error. Unable to view the printer web browser (PageScope Web Connection).
Solution
CAUSE: The reason for the error:
1. A bad request.The browser sent a request that the server could not understand.
2. An attempt to communicatewith plain HTTP to an SSL-enabled server port. Instead, use the HTTPS scheme to access the URL.
3.The request could not be understood by the server due to malformed syntax. The client SHOULD NOT repeat the request without modifications.
Note : The first digit of the status code specifies one of five classes of response.
1xx Informational
2xx Success
3xx Redirection
4xx Client Error
5xx Server Error
SOLUTION: The error can be eliminated by:
1. Checking for any enabled Pop-up blockers and reconfiguring them.
2. Checking for Internet security software that may be blocking Web access and disabling the service. Example: Norton© Internet Security.
3. Installing Microsoft® .NET Framework 1.1 Service Pack 1. Microsoft® has confirmed that this is a problem inMicrosoft® products that are listed in the
"Applies to" section. This problem was first corrected in.NET Framework 1.1 Service Pack 1. Please refer to Microsoft® Article ID: 826437 - FIX: "HTTP 400 Bad request" error message in the .NET Framework 1.1 .
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0801511EN*
Solution Usage
11
Description
TCP socket error occurs when using PageScope Web Connection if latest Adobe® Flash Player (Version 9.0.124.0) is installed. This problem does not occur
on Adobe® Flash Player(Version 9.0.115.0). "Socket connection error" message is displayed in the top center of the screen. Please see attached Web
sample.
Solution
CAUSE: Firmware bug.
SOLUTION: Konica Minolta Japan will be releasingfirmware to correct this issue. Please read the Release Notes to determine ifexisting firmwaremeets your
needs. It will be noted if the firmwarecorrects the issue.
Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/BSE and Cesar Jimenez, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
64
bizhub 360
Solution ID
Software/Driver related
TAUS0701650EN*
Solution Usage
5
Description
Unable to print from Adobe® Acrobat® 8 with the Visual PostScript driver.
Solution
CAUSE:An abnormality with the Visual PostScript driver.
SOLUTION:Visual PostScript drivers areavailable that correct this issue.
Microsoft® Windows NT4/2K/XP/2K3 (32-bit)
bizhub Pro 1050 Visual PostScript driver version 3.2.0.0
bizhub Pro 920 Visual PostScript driver version 2.8.0.0
bizhub 750/600 Visual PostScript driver version 3.1.0.0
bizhub 500/420/360 Visual PostScript driver version 3.1.0.0
Microsoft® Windows XP Pro/2K3 (64-bit)
bizhub Pro 1050 Visual PostScript driver version 3.2.0.0
bizhub Pro 920 Visual PostScript driver version 2.8.0.0
bizhub 750/600 Visual PostScript driver version 3.1.0.0
bizhub 500/420/360 Visual PostScript driver version 3.1.0.0
Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (
http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
SPECIAL NOTE : Solution contribution by Tony Pizzoferrato, ESS/SSD
Solution ID
TAUS0800366EN*
Solution Usage
5
Description
When printing from Microsoft® Publisher andperforming a mail merge, thecopiesare all stapled together.
Solution
CAUSE: This is a known anomaly with Microsoft® applications.
SOLUTION: Please read the attached Microsoft® articleregarding a resolution for the problem with Microsoft® Publisher 2000 and 2003. To viewthe PDF,
Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Mark D'Attilio, Production Print/SSD
Solution ID
TAUS0802710EN*
Solution Usage
3
Description
Error code 2039when performing CSRC (CS Remote Care). TX/RX test is not sent to Lotus ® Domino™ email server.
Solution
CAUSE: The engine will not complete the TX/RX test if the ‘Short name’ field is not populated, becausethe engine will not receive proper POP3 response
from email server.
SOLUTION: Enter a name in the ‘Short name’ field. It is recommend to usethe hostname (the portion to the left of '@' in the engine’s email address). The
attached file is ascreenshot showing the Lotus® Domino™ ‘Short name’ field.
Note: To view the PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
SPECIAL NOTE: Solution contribution by Rick Veale, ESS/BSE
Solution ID
TAUS0701267EN*
Solution Usage
2
Description
When loading ISWTrns on Microsoft® Vista™, USB is not available under Settings.
Solution
CAUSE: Earlier ISWTrns version is being used.
SOLUTION: The USB feature is available in ISWTrns utility version 3.74E and newer.
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
65
bizhub 360
Solution ID
Software/Driver related
TAUS0800367EN*
Solution Usage
2
Solution Usage
2
Description
When duplexing from Microsoft® Publisher 2007 there is a manual duplexing wizard that is opening. This is forcing manual duplexing.
Solution
CAUSE: Duplexing is being selected in the wrong location.
SOLUTION: Select duplexing under the Properties and select Single-sided in the initial print dialog window.
SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD
Solution ID
TAUS0900989EN*
Description
How to obtain spool files from an AS/400 for analysis by the lab.
Solution
Because of the complexityand types of issues betweenMFPs and the AS/400, the Lab may occasionally require that a spool file be provided so that the exact
issue can be re-created by the lab. There aretwo methods to follow, depending upon the OS version on the AS/400.
Follow these steps to obtain the spool file.
1. Obtain the version of the OS/400 that is installed the AS/400 by issuing the following command:
GO LICPGM
(The user will need appropriate rights in order to do this.)
2. When the Work with Licensed Programs menu is displayed, type option 10 to display installed licensed programs.
3. After the list is displayed (it may take awhile), press F11 to display the release version. This will appearunder the Installed Release column.
4. Use theattached instructions to obtain the spool file.
If the OS version is V5R4M0 or higher, then use instructions called
Backing up Spool files System i V5R4Mx.pdf
If the OS version is lower then V5R4M0, then use instructions called:
Instructions to copy spool files off AS400 V5 using FTP-final.pdf
5. After thefiles are obtained,attach them to the SSD ticket.
SPECIAL NOTE: Solution contribution by Paul Santangelo, ESS/BSE
Solution ID
TAUS0902460EN*
Solution Usage
2
Description
How to perform a Mail Merge using Microsoft® Word 2007.
Solution
The attached documentation outlines procedures to:
divide Mail Merge into separate jobs based on name or address
separate a file that has already been merged into Microsoft® Word 2007. In other words, you only have a Word file with all the variable data incorporated. No
need to add recipients from a spreadsheet.
Notes :
1.The instructions are for both scenarios using Microsoft® Word 2007 and attached are the files used in the instructions.
2. To view the DOC file, Microsoft® Word® or Word® Viewer must be installed. Word® Viewer 2003 (11.7MB) can be obtained free from Microsoft® at the
following URL; http://www.microsoft.com/downloads/details.aspx?DisplayLang=en&FamilyID=95e24c87-8732-48d5-8689-ab826e7b8fdf .
3. To view the XLS file, Microsoft® Excel® or Excel® Viewer must be installed. Excel® Viewer 2003 (9.9MB) can be obtained free from Microsoft® at the
following URL; http://www.microsoft.com/downloads/details.aspx?FamilyID=c8378bf4-996c-4569-b547-75edbd03aaf0&displaylang=EN .
4. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
66
bizhub 360
Solution ID
Software/Driver related
TAUS0702369EN*
Solution Usage
1
Description
"Destination device is not supported." message when attempting to connectto the MFP. Thecontrollerfirmware of the bizhub750/600/500/420/360 is later than
version 30.
Solution
CAUSE:TheHDD TWAIN driver requires updating.
SOLUTION: Update tothespecial HDD TWAIN driver ver.3.1.0.2 (15MB) .
Notes :
1. Please refer to the attached ReadMe, Program Release Information and Users Guide.
2. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
3. The latestTWAIN drivers are also available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (
http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0702714EN*
Solution Usage
1
Description
When a PDF is output from Adobe® Acrobat® 8, it generates a PostScript error.
Solution
CAUSE: Bugin theKonica MinoltaVisual PostScript driver when settings are as follows:
- Visual PostScript driver: “Path through - Off”
- Adobe® Acrobat® 8: ”Choose Paper Source by PDF page size”
SOLUTION: Please use the special Konica MinoltaVisual PostScript driver (32-bit or 64-bit as needed), version 3.1.0.0.
Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (
http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0703335EN*
Solution Usage
1
Description
Why, when printing to HDD using PCL driver, doesa warning message appears before storing the job?
Solution
To eliminate the popup window update the PCL driver. Pleaserefer tothe following.
Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from the KMBS public site (
http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
bizhub C450
1. Release version and download file name
Following program version is explained in this file.
[Release version]
Product name
Program name
Based version
Release version
Language
Installation type
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
67
bizhub 360
Software/Driver related
Note
C450
KONICA MINOLTA C450 PCL Driver
03.02.02.00
03.02.02.02
English
Add type
Windows 2000/XP/Server2003
[Download file name]
c450_pcl_win2k_xp_2k3_v03020202_en_add.exe
PRI_DLBT0703015EN.doc (this file)
2. Where changed
This program is released for the following purpose.
This driver is released for the following purpose.
And, please install this special driver only to the PC of a necessary customer.
When selected “Save in User Box” and “Save in User Box and Print” in Output Method, the confirmation dialog for setting doesn’t show.
3. Restrictions
None
4. Programs to be applied at the same time
There is no program to be applied with this KONICA MINOLTA C450 PCL Driver.
However, using with latest version program is recommended.
5. How to install
5.1. How to update the driver
Open the Printer folder by selecting [Start] => [Settings] => [Printer], and please select the [Add Printer] icon.
5.2. How to check version
Open the properties of printer driver, and check the version in the order of Setup ->Version tab.
bizhub C252/C252P
1. Release version and download file name
Following program version is explained in this file.
[Release version]
Product name
Program name
Based version
Release version
Language
Installation type
Note
C252
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
68
bizhub 360
Software/Driver related
KONICA MINOLTA C252/C252P PCL Driver
03.02.01.00
03.02.01.08
English
Add type
Windows 2000/XP/Server2003
[Download file name]
c252_pcl_win2k_xp_2k3_v03020108_en_add.exe
PRI_DLBT0703014EN.doc (this file)
2. Where changed
This program is released for the following purpose.
This driver is released for the following purpose.
And, please install this special driver only to the PC of a necessary customer.
When selected “Save in User Box” and “Save in User Box and Print” in Output Method, the confirmation dialog for setting doesn’t show.
3. Restrictions
None
4. Programs to be applied at the same time
There is no program to be applied with this KONICA MINOLTA C252/C252P PCL Driver.
However, using with latest version program is recommended.
5. How to install
5.1. How to update the driver
Open the Printer folder by selecting [Start] => [Settings] => [Printer], and please select the [Add Printer] icon.
5.2. How to check version
Open the properties of printer driver, and check the version in the order of Setup ->Version tab.
bizhub 500/420/360
1. Release version and download file name
Following program version is explained in this file.
[Release version]
Product name
Program name
Based version
Release version
Language
Installation type
Note
ic204
KONICA MINOLTA
500/420/360 PCL Driver
03.01.00.00
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
69
bizhub 360
Software/Driver related
03.01.00.06
English
Add type
Windows 2000/XP/Server2003
[Download file name]
ic204_pcl_win2k_xp_2k3_v03010006_en_add.exe
PRI_DLBT0703017EN.doc (this file)
2. Where changed
This program is released for the following purpose.
This driver is released for the following purpose.
And, please install this special driver only to the PC of a necessary customer.
When selected “Save in User Box” and “Save in User Box and Print” in Output Method, the confirmation dialog for setting doesn’t show.
3. Restrictions
None
4. Programs to be applied at the same time
There is no program to be applied with this KONICA MINOLTA 500/420/360 PCL Driver.
However, using with latest version program is recommended.
5. How to install
5.1. How to update the driver
Open the Printer folder by selecting [Start] => [Settings] => [Printer], and please select the [Add Printer] icon.
5.2. How to check version
Open the properties of printer driver, and check the version in the order of Setup ->Version tab.
SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/SSD
Solution ID
TAUS0655341EN*
Solution Usage
0
Description
In Microsoft® Publisher 2002/2003, publications/records are not individually collated and stapled when duplexing and using the Mail Merge feature.
Solution
CAUSE: Registry edit required.
WARNING : In Microsoft® Windows, system configuration information is centrally located in the registry. While this simplifies the administration of a
computer or network, one incorrect edit to the registry can disable the operating system. The following list provides some best practices for using the registry
and Registry Editor safely:
Before making changes to the registry, make a backup copy.
Back up the registry by using a program such as Backup. After making changes to the registry, create an Automated System Recovery (ASR) disk. For
troubleshooting purposes, keep a list of the changes you make to the registry. For more information, see System State data.
Do not replace the Microsoft® Windows registry with the registry of another version of the Microsoft® Windows or Microsoft® Windows NT-type operating
systems.
Use reliable tools and programs other than Registry Editor to edit the registry.
Incorrectly editing the registry may severely damage the system. Use tools and programs that provide safer methods for editing the registry.
Never leave Registry Editor running unattended.
Konica Minolta is not responsible for any system errors that may result from using a registry editor incorrectly.
SOLUTION: Microsoft® Publisher can be enabled to individually collate, staple and duplex publications/records when using the Mail Merge feature of
Publisher through a registry edit. This can be done either manually or by a script.
To manually edit the registry
Open the Registry Editor by clicking Start, click Run, type regedit , and then click OK. Go to:
1. HKEY_CURRENT_USER\Software\Microsoft\Office\ \Publisher\Printing
2. Right-click on the Printing folder, select New => String Value.
2. Create new "string value" called: NumberOfRecordsPerBatch
3. Double-click and set the Value Data to 1 . Instead of grouping records together into groups of 10to send to the printer (Publisher default), the records are
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
70
bizhub 360
Software/Driver related
now sent in groups of 1 (i.e., each document is sent separately).
Note : A value for this size setting can be set between 0 and 99999.
To update the registry "automatically" from a script
1. Download the scriptfrom http://ed.mvps.org/20031Rec.reg and save the REG file to the Desktop (script is also attached in case the URL cannot be
accessed).
2. Double-click on the icon, and then click on Yes to the question, "Are you sure you want to add the information in C:DOCUME~1\administrator account
\Desktop\20031Rec.reg to the registry?"
3. The new value will be added to the registry.
Note :Refer to Windows registry information for advanced users ( http://support.microsoft.com/kb/256986 ) for additional registry editinformation.
Solution ID
TAUS0802060EN*
Solution Usage
0
Description
When printing AS/400® forms, the print does not line up with the form.
Solution
CAUSE:The AS/400® is rasterizing the forms based on an HP® LaserJet 5si (this is by design).The margins are not set correctly and produces the offset.
SOLUTION:Create or obtain a new WSCST (Workstation Customization Object)with the following keyword in it.
DATASTREAM=HPPCL5
Replace the line with the following:
DATASTREAM=HPPCL5I
Thiswill tell HPT to image the form instead of rasterize it.
Recompile the WSCST, end the writer, vary the device description OFF/ON and start the writer.
When the job is sent, the form should be inline with the text.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/BSE
Solution ID
TAUS0702713EN*
Solution Usage
Description
When printing from Adobe® Acrobat® 8, the print stops at page 45 and next page or later is not printed.
Solution
CAUSE: Bugin theKonica MinoltaVisual PostScript driver.
SOLUTION: Please use the special Konica MinoltaVisual PostScript driver (32-bit or 64-bit as needed), version 3.1.0.0.
Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (
http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0702715EN*
Solution Usage
Description
When printing from Adobe® Acrobat® 8, the image of the last page is rotated by 180 degrees.
Solution
CAUSE: Bugin theKonica MinoltaVisual PostScript driver.
SOLUTION: Please use the special Konica MinoltaVisual PostScript driver (32-bit or 64-bit as needed), version 3.1.0.0.
Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (
http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0702717EN*
Solution Usage
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
71
bizhub 360
Software/Driver related
Description
A PDF cannot be output from Adobe® Acrobat® 8.
Solution
CAUSE: Bugin theKonica MinoltaVisual PostScript driver.
SOLUTION: Please use the special Konica MinoltaVisual PostScript driver (32-bit or 64-bit as needed), version 3.1.0.0.
Note : The latest print drivers are available via the Konica Minolta Download Selector. Access the Selector from theKMBS public site (
http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers,
Firmware and more'.
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0800566EN*
Solution Usage
Description
When printing from special application, prints a blank page at the end of the print job.
Solution
CAUSE: The application may have added margins that cause the blank spacethus creating an extra page.
SOLUTION: To prevent this:
1. Access the UTILITY on the machine.
2. Select User Settings.
3. Select Printer Settings.
4. Select PCL Settings. The display willindicate MODE 1, MODE 2, MODE 3 and ON or OFF(default).
5. Select ON and MODE 3.
6. Exit to basic screen.
7. PowerOFF machine, wait 5 seconds, thenpower ON.
8. Send test job.
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0801431EN*
Solution Usage
Description
When too many users simultaneously attempt to perform PageScope Box Operator functions while accessing the same MFP, it is possible that the
PageScope Box Operator (PSBO)application may lock up intermittently. The PSBO application and/or the MFP may need to be restarted in order to resume
using the PSBO application.
Solution
CAUSE: It is possible for multiple users to connect to the same MFP simultaneously through PSBO. However, only one document can be downloaded at a
time from the same device, either through PSBO or PageScope Web Connection (PSWC). As a result, if two or more users attempt to download a document
in a box by PSWC or PSBO simultaneously from the same MFP, the second user will have to wait until the previous download is completed.
SOLUTION:If the lockup issue occurs, the number of simultaneous connections from PSBO to the same MFP will need to be reduced. It is possible that this
specification may be changed for future models.
SPECIAL NOTE : Solution contribution by Mark Kemp, ESS/SSD
Solution ID
TAUS0801980EN*
Solution Usage
Description
"Device can not print in accordance w/guidelines pick another printer" message when trying to print postage from Stamps.Com.
Solution
CAUSE: Driver incompatibility.
SOLUTION: Stamps.com states that they will not work with Konica Minoltadrivers.The only thing they will do is print labels, and you have to purchase the
labels from Stamps.com.
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
72
bizhub 360
Solution ID
Software/Driver related
TAUS0802412EN*
Solution Usage
Description
Slow printing issue when utilizing Macintosh® OS 10.4.x.
Solution
CAUSE: Issue with the CUPS daemon configuration file on Macintosh® OS 10.4.x. being corrupt.
SOLUTION: The old CUPS daemon configuration file must be deleted and a new one created. Please see the attached document for instruction on how to
remove and re-create the daemon configuration file.
SPECIAL NOTE : Solution contribution by Tim Blevins - KMBS/Cleveland
Solution ID
TAUS0808509EN*
Solution Usage
Description
When printing from an AS/400, the job reprints and an asterisk is displayed by jobname on the user console.
Solution
CAUSE:When an AS/400 is set up to perform remote printing, it uses the LPR protocol. When printing multiple copies in this configuration, the AS/400sends
a control file that contains multiple entries for each job that is sent.When the MFP receives this file, it drops the connection immediately;the AS/400,
confused,resends the same page each time.
SOLUTION:Install the latest firmware for each model, whichshould correct thisissue. Ifit does not, then use the following firmware for specific models to
correct the issue and report back tothe Hotline.
bizhub 200/250/350/40P: 200_250_350_4040-0100-G3V-80-002.ZIP
bizhub 360: 360us_m0g1300d1.exe
bizhub 420: 420us_m0g1300d1.exe
bizhub 500: 500us_m0g1300d1.exe
bizhub 361: 361us_m1g1300c5.exe
bizhub 421: 421us_m1g1300c5.exe
bizhub 501: 501us_m1g1300c5.exe
bizhub 600/750: 600_750_us_m1g3000da.exe
bizhub PRO 1050: 1050_p131cpf0p.exe
bizhub C451: C451_A00K0Y0-F000-GC2-R4.EXE
bizhub C550: C550_A00J0Y0-F000-GC2-R4.EXE
bizhub C650: C650_A00H0Y0-F000-GC2-R4.EXE
bizhub C203: C203_A02E0Y0-F000-GE2-R4.EXE
bizhub C253: C253_AO2E0Y0-F000-GD2-R4.EXE
bizhub C353: C353_A02E0Y0-F000-GC2-R4.EXE
bizhub C353P: C353P_A02EY0-F000-GW1-72.EXE
Note:The firmware is available for download via the Konica Minolta Download Selector..
1. Login in via www.mykonicaminolta.com
2. Select the "Service" tab located at the top of the page.
3. Select the "SSD (DNA, Drivers, MSDS)" link located to the left.
4. Select the "Continue on to the SSD Home Page" link located in the middle of the page.
5. Select the "Download MSDS, Drivers, Firmware and more" link located to the left.
6. These files are located under "Specials".
SPECIAL NOTE: Solution contribution by Paul Santangelo, ESS/BSE
Solution ID
TAUS0900976EN*
Solution Usage
Description
After NVRAM replacement the MFP does not ask to enter Equitrac© code.
Solution
CAUSE: Equitrac© device has been unset.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
73
bizhub 360
Software/Driver related
SOLUTION: Reenable the Equitrac© device:
1. Enter the Service mode.
2. Press [STOP], [9] on the operation panel to enter the Security mode.
3. On the Billing setting screen press [Management Function Choice].
4. Choose [Key Counter Only] to enable the Equitrac©.
5. Press [END].
6. Press [Exit].
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Solution ID
TAUS0901089EN*
Solution Usage
Description
Microsoft® Word does not return to the default printer when closed and reopened.
Solution
CAUSE: Microsoft® Outlook is open and is using Microsoft® Word asthe default program for editing messages.
SOLUTION: To change the default mail message editing program perform the following:
1. Go into Microsoft® Outlook and select Tools from the tool bar.
2. Scroll down to Options.
3. Click on the Mail Format Tab.
4.Make sure the Use Microsoft Office Word 2003 to edit e-mail messages checkbox is selected.
Note : In versions before Microsoft® Outlook 2003, the text reads Use Microsoft Word to edit e-mail messages . In Microsoft® Outlook 2007, there is no
longer an Outlook editor. The default is Microsoft® Word and cannot be changed.
5. Close the dialog.
SPECIAL NOTE : Solution contribution by Jim Behrends, Production Print/SSD
Solution ID
TAUS0901351EN*
Solution Usage
Description
How is the fax stamp and its settings enabled?
Solution
The fax stamp and its settings are enabledby performing the following:
1. Enter the service mode.
2. Select system 2.
3. Select DIPsw settings.
4. Change SW 37 bit 1 to a 1.
5. Press Set.
6. Cycle machine power.
SPECIAL NOTE: Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0902084EN*
Solution Usage
Description
How to push driver properties down to clients from a Netware server.
Solution
Bcause of the nature of how drivers are installed in the NDPS database, driver properties can not be saved.
Novellacknowledged this limitation; inNetware 6.5 and above there is a function called the Driver Profile.Use the following instructions to allow driver
properties to be downloaded from the client when the printer driver is downloaded from the NDPS database.
Before creating the profile, the following items must be installed on the Netware 6.5 server:
1.SP5 or above, including all patches.
2.iPrint version 4.2.8 or higher.
3.TheiPrint LIB files must be updated.
These files can be found at http://www.novell.com
To install:
1.In Novell iManager, click iPrint > Print driver profile.
2.Browse to and select the print manager where you want the driver profile stored and made available to the printers on that manager
3.Select an operation and click OK (create, delete, modify)
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
74
bizhub 360
Software/Driver related
After creating a printer driver profile associate it with a printer:
1.In Novell iManager, click iPrint > Manage printer.
2.Browse to and select the printer you want to modify.
3.Click drivers > printer_driver_operating_system.
4.Select the printer driver from the list of available printers.
5.Select the profile you want associated with this driver from the list of available driver profiles for the selected driver
6.Select OK to save the changes.
Note:If you experience winsock 11004 issues when creating the driver profile, update the local HOSTS file on the workstation with the IP address of the server
and its DNS entry.
SPECIAL NOTE: Solution contribution by Paul Santangelo, ESS/BSE
Solution ID
TAUS0902136EN*
Solution Usage
Description
While upgrading the firmware on a MPI LinkCom™ III print server using Microsoft® Windows Vista™, the update may fail.
Solution
CAUSE: Anomalywhen attempting firmware install using Microsoft® Windows Vista™.
SOLUTION:The only known solution is to use Microsoft® Windows XP and recycle the print serverbefore performing the upgrade again.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
75
bizhub 360
Solution ID
Warm-up, wrong display, incorrect operation, lock-up
TAUS0657486EN*
Solution Usage
61
Description
C2403 (C-2403).
Solution
PROBABLE CAUSES:
bizhub 360/420/500/361/421/501
1. Damaged wires on the TCRS sensor.
Note : C2303 (C-2303) may also be indicated with "Toner recharging" message.
Replace the TCRS sensor (p/n 26NA 8804 1).
2. The toner supply motor failed.
To test the motor:
a. Enter the Service mode.
b.Select State/Confirmation, then Load Check.
c.Enter code 56, multi-code 001 and press the print key. Verify the toner supply motor turns smoothly in a clockwise direction.
d.Press stop.
e.Enter multi-code 002 and press the print key. Verify the toner supply motor turns smoothly in the counterclockwise direction.
If the motor hesitates in either direction, replace the toner supply motor (p/n 26NA 8006 1).
SPECIAL NOTE : Solution contribution by Mike Galletta and John Miller, Workgroup/SSD
bizhub 360/420/500
1. When an empty toner bottle is rotated while removing it from the machine, the alignment tab goes out of home position. Then, when a new bottle is
inserted, it does not rotate correctly.
A modification is available. Please refer to attached Bulletin Number 5775 and follow the procedures outlined. To view the PDF, Adobe Reader® must be
installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
Note : To reset C-2403 after replacing the toner bottle, perform the following:
a. Power OFF the main switch (SW2, inside front door).
b. Slide the toner bottle cradle and remove spent toner bottle.
c. Prepare new toner bottle per instructions and place toner bottle in the cradle (line up the two notches at the rear so the cartridge is laying level in the
cradle).
d. Turn bottle completely around and line up the arrow at the 12 o'clock position clockwise or counterclockwise and push cradle in and lock toner door.
e. The power should be re-enabled to ON while holding the Utility key; the Konica Minolta blue screen within 6 minutes, then the white screen with Trouble
Reset. Touch and OK will appear.
f. Power OFF/ON and should go to Ready. This procedure may have to be redone several times.
2. Toner bottle is not turning.
Ensure that the toner bottle does not have any manufacturing defects. Also ensure that the pressure spring inside the pressure assembly (p/n 26TA-3332) is
applying sufficient pressure when locked into place.
3. Excessive pressure from the Toner Bottle Door.
Remove the pressure springs (Toner Supply Unit (TSU), item #7 - see attached) located in toner door.
4. The toner bottle position sensor (PS28) may have shifted when the drive section on the back of the machine was removed or installed. As a result, PS28
cannot detect rotation of the toner bottle.
Install a new mounting plate (p/n 50GA33161E) and stopper seal (p/n 4470402481) for PS28. These parts prevent PS28 from becoming dislodged. Complete
details are in attached Bulletin Number 6078.
5. Contact between parts around the bottle guide section.
Please install the Toner supply auxiliary cover countermeasure as explained in the attached Parts Modification Notice.
6. If toner bottle is not installed correctly and the customer forces it then it may cause tearing of the drive tabs on the toner bottle. This will cause the bottle
not find the home position generating this error.
Please ensure that the toner bottle is inserted correctly. Refer to Bulletin 5471 for details on a modification to the toner guide assembly.
7. Even though the correct procedure was used per Bulletin Number 5471 , there still may be burrson theflange tips at neck of the toner bottle.Also,PS4
and PS28 may not be sensing properly.
Verify the correct operation of PS4 and PS28. Check for burrson theflange tips at neck of the toner bottle. Use Scotch-Brite™ to remove the burrs on the
toner bottle.
Note : The service documentation does not include a procedure for checking PS4 (Toner Bottle Sensor) and the PS28 (Toner Bottle Position Sensor). To
check:
a. Enter the State Confirm mode=>'Service Mode screen'; press [State Confirmation].
b.'State Confirmation screen'; press [Sensor check].
c. 'Sensor Check screen'; press [Check Code] and, when entering the sensor check code in 3-digit format through the copy count setting button, a state
(ON/OFF) or value is displayed in the Result area.
d. For the multi-mode, press [Multi Code] and enter a three-digit multi-code through the copy count setting key. When conducting the sensor check of other
signal sources, repeat stepscand d.
IMPORTANT : Code 57, multi-mode 2, which is not listed in the bizhub 420/500 Service Manual, is used to monitor the output signals ofPS4 (Toner Bottle
Sensor), and multi-mode 3 for monitoring the output signal ofPS28 (Toner Bottle Position Sensor). These sensors are located at the rear of the hopper
assembly at the 11 o’clock position forPS28 and at the 12 o’clock position forPS4. The state of these sensors will switch from 0 to 1 if the bottle is moved.
8. Excessive toner misting due to openings in Toner supply holding main body (p/n 26NA32311E).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
76
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
Clean the partthoroughly with alcohol.Applya coveringlike electrical tape to cover the openings as shown in the attached file.
CAUTION :Do not cover the opening from which the toner is added to the developer.
SPECIAL NOTE : Solution contribution byVal Kenney, Southern Region DSMandPaul Speicher,Charlotte Copy Data.
9. Certain parts involved with the toner bottle become misaligned during the process of changing toner bottles. When the toner bottle is replaced, the toner
bottle index part could rotate out of position. Subsequently, a customer would install a new toner bottle while the index part was out of home position.
A boss has been added to the toner supply guide part assembly, and a corresponding notch has been made in the toner supply index part. Replacing these
two parts will eliminate accidental rotation of the index part as a cause of this error code. Replace these parts as a set. Please refer to attached Bulletin
Number 6496 for more detail.
bizhub 361/421/501
CAUSE:If the tray is pulled outwhen a toner bottle is being removed, the toner supply index part may turn from thecorrect position.
Atoner supply guide tray is pushed downwhen removing, and also the bottle ispulled outwithout drawing the tray out completely.
SOLUTION: Please mark the positionshown theattached filewith a whitemarking pen. If the white mark andthe arrow of index part has a gap, please fix the
position and reload.
Note :To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by KMBT (Japan).
Solution ID
TAUS0700056EN*
Solution Usage
24
Description
C-6701 (C6701) or C-6702 (C6702) at power up. TheMFP scans to home position and the exposure lamp lights. If code is indicated during copy cycle, copies
may be all black.
Solution
PROBABLE CAUSES:
1.Failed Overall Control Board (OACB).
Check ICP3 on the OACB. If it is OPEN, checkfor shorts andreplace the Overall CB (p/n50GA -930 4M for bizhub 360/420/500 and p/n A0R5 H010 06 for
bizhub 361/421/501 ).
2.A communication issue between the CCD and OACB. Thisissue usually appears shortly after replacing or removing the OACB (Overall Control Board).
Please check the flat cable between the CCD and OACB. Make sure it is undamaged and connected properly. Replace the CCD cable (p/n 50GA 9050 0)if
reseating it has no effect on the service code.
3. During start up the CCD sensor is not initializing properly. Light from the exposure lamp is not being reflected by the white patch located under the platen
glass to the CCD sensor via the optics.
Make sure the optics is intact and positioned properly. Make sure the platen glass is also placed properly. The CCD also should be connected properly and
positioned properly. Be sure the cover for the CCD assembly is mounted correctly. Replace the CCD (p/n 50GA -626 1) if the optics and exposure system are
functioning properly.
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD; Jim Arnott -Perry Corporation and Phillip Britt, Albin Business Centers
Solution ID
TAUS0654285EN*
Solution Usage
23
Description
C-E082 (CE082). C-E084 (CE084) may also be indicated.
Solution
PROBABLE CAUSES:
1.Possible failed parameter memory board assembly or firmware bug ( bizhub 360/420/500 ).
Please upgrade the firmware to minimum level 14.0. The latest version firmware or system software is available via the Konica Minolta Download Selector.
Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
If the problem still persists,a call MUST be placed to the SSD Hotline at 800-825-5664 to determine if the NVRAM has failed. A large number of suspected
NVRAM failures turn out to have different root causes.SSD/ESS will assist in determining such situations.
If the NVRAMhas failed:
acquirea Problem Ticket number
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
77
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
go to www.mykonicaminolta.com ;select Service tab=> Warranty, Repair & Special Programs => RA Form. Fill outthe RA Form.
This is absolutely imperative to comply with ISO standards upon the return of the core. SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/SSD
2. The OACB firmware has become corrupt or the OACB has failed.
Note : This may occur at power up orwhen scanning.Possibly can be cleared bypowering MFPOFF/ON but will reoccur.
Reflash the firmware to the OACB andif this does not resolve the problem, replace the OACB (p/n 50GA -930 3Kfor bizhub 360; p/n 50GA-930 1H for bizhub
420/500 and p/n A0R5 H010 06 for bizhub 361/421/501). The latest version firmware or system software is available via the Konica Minolta Download
Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD and Chuck Tripp, Production Print/SSD
Solution ID
TAUS0657589EN*
Solution Usage
19
Description
C-3201 (C3201) indicated.
Solution
bizhub 420/500
CAUSE: A motor speed abnormality of the Fusing Motor (M11). When M11 is ON, an EM error signal is detected 30 times in succession within a specified
period of time. Bad connection between the Fusing Motor (M11) and the Printer Control Board (PRCB).
SOLUTION: Check to make sure the connections between the Fusing Motor (M11) and the Printer Control Board (PRCB) are made correctly by unplugging
and reseating them. Try switching the Fusing Motor (M11) and the Drum Motor (M1) since these motors are exactly the same. If the service code is
unchanged, replace the Printer Control Board (p/n 50GA-9020E). If the service code changes to a C-2202, replace the Fusing Motor (p/n 27LA-80030).
SPECIAL NOTE : Solution contribution by Ken Walker, Workgroup/SSD
bizhub 360/420/500
CAUSE: Inadequate lubrication of the fixing (fusing) unit gears, whichprevents the fixing motor from turning at the proper speed.
SOLUTION: Remove the fixing unit, disassemble the input gear assembly, and clean the factory lubricant from gear bores and shaft. Reassemble after
applying a suitable high temperature grease.
SPECIAL NOTE : Solution contributed by Raymond Berger, OASYS, Inc., SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
bizhub C250/C252/C300/C352
Jams at fuser; paper not crumpled, just stops. Jam history indicates 3201 jams.
PROBABLE CAUSES:
1.Fusing Drive Motor failure to turn.
Check connections on the Fusing Drive Motor and make sure it is working properly.Check Fusing Unit for proper connection.Change the bizhub C250
PWB-MFP(p/n 4038012106)or the bizhubC300/C352 PWB-PRCB (p/n 9J06012106).FlashMFP with current firmware.
Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
2. The FS-514 finisher exit motor (M4)has failed.
Replace the finisher exit motor(p/n 9J08 M102 00).
SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD and Cesar Jimenez, Production Print/SSD
bizhub C250/C250P/C252/C252P
CAUSE: Jam is incorrectly detected due to malformed (by heat) fuser actuator.
SOLUTION: Replace the Fusing Unit witha modified Fusing Unit (Lot Number for modified Fusing Unit: 071129)orinstall the modified
heat-resistantActuator(p/n 4038-5728-03) into theexisting Fusing Unit. Current Fusing Unit part numbers - 4038 R773 00 forbizhub C252/C252Pand 4038
0754 00 for bizhub C250/C250P.
SPECIAL NOTE : Solution contribution by KMBT (Japan).
bizhub C351/C450/C450P
CAUSE: Material may have entangled in the exit rollers causing too much friction. This in turn causes the fuser drive motor to run slower than normal.
SOLUTION: Open the right side door and verify the exit rollers (p/n 4025 5901 02) rotate smoothly. If there is too much friction, remove the exit rollers and
check for any foreign material.
SPECIAL NOTE : Solution contribution by Gary Scimeca, Production Print/SSD
bizhub C203/C253/C353
PROBABLE CAUSES:
1. Failed DCPU and/or fuser motor (M5).
Check for 24V DC at DCPU CN10, pin 1. Replace DCPU if no 24V DC present at DCPU CN10, pin 1 (p/n A02E M400 01). If deemed necessary, replace
fuser motor M5 (p/n A02E M100 00).
2. Failed PRCB (PWB-MC).
Replace PRCB (p/n A02EH00106).
3.Binding fusing unit or possible failed fusing motor.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
78
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
Prior to replacing the fusing motor (M5), please perform the following:
a. Confirm that the fusing motor CN79 is firmly seated.
b. Remove the fusing unit and ensure that the fuser rollers turn freely and are not restricting the rotation of the fusing motor.
c. Inspect and reseat CN34 on the PRCB which is the interface connector for the fusing motor (M5).
d. Replace the fusing motor (p/n A02E M100 00) as necessary.
SPECIAL NOTE : Solution contribution by Mike McCarthy and Ted Young, Production Print/SSD
Solution ID
TAUS0801518EN*
Solution Usage
15
Description
No MFP operation.The LCD panel is lit blue and the data light on the control panel is lit solid. TheOACB (Overall Control Board) was just replaced.
Solution
CAUSE: A blue screen and solid data light indicate the Image firmware on the OACB has been cleared or become corrupt. New OACBs do not come with
Image Firmware installed and will also produce the same issue.
SOLUTION: To repair this issue the Image ROM must be re-installed. In most cases the firmware will need to be updated with ISW and a parallel connection.
USB will not work. Send the “Control All” firmware choice in ISW to theMFP after poweringON. As soon as the data light is illuminated, send the file to the
MFP. The data light should blink indicating the update is taking place. Please make sure not to disturb theMFP in any way as long as the data light is blinking.
After approximately 10 to 20 minutes the data light will stop flashing, the document handler will bump and cycle andthe MFPwill power up with the panel.
Please be patient. If theMFP is stopped in the middle of this update or if the data light fails to light solid, the OACB Overall Control Boardhas failedand should
be replaced.
Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
SPECIAL NOTE : Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0652777EN*
Solution Usage
12
Description
C-C183 (CC183).
Solution
After replacing Overall System Control Board
CAUSE: When replacing theOverallControl Board, the "new" board does not have system code loaded.
SOLUTION: Flash the OverallControl Board with current firmware.The latest version firmware or system software is available via the Konica Minolta Download
Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
After flashing the firmware
CAUSE: The machine was flashed with firmware for another model.The model setting in ISW on the computerwas accidentally setto the wrong model.
SOLUTION:To re-flash:
1.PowerOFF the machine, hold the Utility/counter key and power up the machine. Keep holding the key for at least 15 seconds.
2. Wait for the Trouble Reset screen. Do not run the Trouble Reset. Enter STOP, 0, 0, STOP, 0, 1. Thisaccesses the Service Mode.
3. Set up ISW and useversion 20 firmware.
4. First send the boot file. The boot file will erase the flash ROM.
5. Next sendversion 20 firmware.
6.Onceversion 20 firmware is uploaded, the machine should boot like normal and the code should be gone.
7.Continue upgrading to the latest version firmware. The latest version firmware or system software is available via the Konica Minolta Download Selector.
Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
After replacing the Printer Control Board (PRCB)
CAUSE: When replacing the Printer Control Board, the "new" board may have system code loaded because of board return or board repair.
SOLUTION: Flash the Printer Control Board with the current firmware. The latest version firmware or system software is available via the Konica Minolta
Download Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
Note : In the case of the bizhub 420 and bizhub 500 it may be necessary to re-load the firmware, starting with special version 13-C2 if the machine displays
a blue screen after attempting to flash it with the current firmware.
To re-flash, starting with v. 13-C2:
1. Power ON the machine.
2.Using ISW, send v. 13-C2 firmware to the machine. Wait for the machine display to return.
3. Using ISW send the boot file for version 20. The boot file will erase the flashROM.
4. Next send version 20 firmware.
5. Then load version 30 firmware.
6. Finally, load the current version of firmware.
SPECIAL NOTE : Solution contribution by Ken Walker, David Silversteinand Bill Hall, Workgroup/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
79
bizhub 360
Solution ID
Warm-up, wrong display, incorrect operation, lock-up
TAUS0703844EN*
Solution Usage
12
Description
C2801 (C-2801) code possibly accompanied by agray background on copies.
Solution
PROBABLE CAUSES:
1. The HVPS has failed.
Replace the HVPS (p/n 50GA84010).
SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD
2.A TCR output abnormality; the TCR output is in excess of 3.0V DC. This is usually due to a severe undertoning or a failed TCR sensor. It is possible to run
the Toner Auto Condition mode under the Service Mode =>Image Adjust Mode. Running this setting will automatically add toner to the developer if
depleted. If the Auto Toner Condition mode fails to correct the issue, the developer and the TCR sensor should be replaced.
Replace thedeveloper and TCR sensor (p/n 26NA-8804-1).Be sure to reference the attached Field Service Manual pagesand perform all adjustments
associated with developer replacement.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
SPECIAL NOTE : Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0801161EN*
Solution Usage
9
Solution Usage
8
Solution Usage
7
Description
CE002 (C-E002) code after flashing the machine firmware.
Solution
CAUSE: The firmware has been upgraded from an earlier version and now the HDD (HD-505/HD-509) has to be "versioned up".
SOLUTION: Please version up the HDD.
1.Enter the Service mode.
2.Select State confirmation.
3.Select Memory/HDD Condition.
4.Select HDD Version Up and hit start.
5.Power cycle the machine from the main power switch when indicated and the code should be gone.
SPECIAL NOTE : Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0701100EN*
Description
C6001 code at start up.
Solution
CAUSE: Ribbon cable going into the CCDto the OACB has become disconnected.
SOLUTION: Reseat the ribbon cable into the connectorsfor the CCD and the OACB.
SPECIAL NOTE: Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0701061EN*
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
80
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
Description
FS-510, C-1102 code after installation of the OT-601.
Solution
CAUSE: The OT-601 was not installed correctly at setup.
SOLUTION: Verify that step 7 of the attached InstallationManual has been performed. Make sure that the Short Connector, supplied with the OT-601, is
plugged into the empty finisher connector as shown in the OT-601 Installation Manual.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0808252EN*
Solution Usage
7
Solution Usage
6
Description
Problem:
The machine has a blue screen and the data light is NOT lit.
Solution
Cause:
The OACB has failed.
Solution:
Please replaced the OACB (p/n 50GA-930 4M).
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0653520EN*
Description
Scan to E-mail and Scan to SMB not listed or not available in the address book or for Direct Input after updating the main body firmware orafter changing
Vendor Mode.
Solution
CAUSE: E-mail and SMB functionality is not enabled.
SOLUTION: To enable SMB and E-mail scanning, perform the following:
1. While in Copy mode, press the Utility button.
2. Press Administrator Setting and enter the default passcode (12345678).
3. Select 5) Network Setting.
4. Select 6) SMB Setting.
5. Edit Scan Setting to ON.
6. Select 9) E-mail Setting.
7. Edit E-mail TX (SMTP) to ON.
8. Enter the Host Address of the SMTP server and exit out of mode.
SPECIAL NOTE: Solution contribution by Chuck Tripp, Production Print/SSD, SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD
Solution ID
TAUS0701815EN*
Solution Usage
6
Description
PROBLEM: J1100or J1200 codeswhile jamming from Tray 1or Tray 2.
Solution
PROBABLE CAUSES:
1.Paper feed drive motor M9 has failed.
To verify the paper feed drive motor M9 has failed, check for 24V DC at PRCB CN32 pins 1 & 2. If24V DC is not detected, replace the paper feed drive
motor M9 (p/n 27LA80030).
3. Check for 5v on pin B11. If not present, measure DCPS CN20-1, CN20-2, CN20-6 for 24v. If one missing, replace the DCPS (p/n 50GA84510).
2. On occasion, when paper is fed from Tray 1 only, the paper may hit a main body guide after leaving the paper feed unit, resulting in a paper jam (J1100).
The position of the paper feed unit guide plate may shift downward, permitting paper to run into the main body
guide.
Install two collars between the upper and lower reinforcement plates to prevent the parts from shifting in affected machines.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
81
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
Please refer to attached Bulletin Number 6524 for serial number information and collar installation procedure. To viewthe PDF, Adobe Reader® must be
installed. Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
3. Failed PS1 (J1100 only).
CheckPS1 in State confirm, sensor check 16, multicode 5. Paper present =1 (ON) which is the default and no paper =0 (OFF). If no change, replace PS1 (p/n
13QA 8552 1).
SPECIAL NOTE: Solution contribution by John Miller, Workgroup/SSD
Solution ID
TAUS0800855EN*
Solution Usage
6
Description
Backlight of the operational control panel display is lit, but the display is blank.
Solution
CAUSE:Failed System control board (OACB).
SOLUTION: Replace the System CB (p/n 50GA -930 4O for bizhub 360/420/500 and p/n A0R5 H010 06 for bizhub 361/421/501 ) as necessary.
SPECIAL NOTE : Solution contribution by Gerald Koehl of Braden Business Solutions and Micheal Johnson, KMBS/SF
Solution ID
TAUS0703714EN*
Solution Usage
5
Description
Power up machine andbasic copy screenis in Japanese.
Solution
CAUSE: New replacement NVRAM was installed and NVRAM was left in Market area that it was tested prior to shipping.
SOLUTION: To change:
1. Access the Utility/Counter then touch the top button on left side (details).
2. Then do Stop 00 Stop 01 and selectthird button on left column (System 1); then on right sidefirst columnfirst button (Market area); then select top rowthird
button, the middle button (U.S.). Nowscreen is in English.
3. Select Serial Number and input all serial numbersneeded.
4. Run the TCR adjustment as well.
Note : The top one is necessary but the others are optional.
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0703855EN*
Solution Usage
5
Solution Usage
5
Description
How to enable network settings when no Network settings button is available in the Administrator settings.
Solution
CAUSE: The network settings have become corupt.
SOLUTION: Reinitialize the Network settings data. To reinitialize the Network settings data, perform the following.
1. Enter the Service mode.
2. Select System 1.
3. Select Initialization.
4. Select Network Settings Data and press start.
SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0807903EN*
Description
When copying from the glass, the user must click "finish" before output begins.
Solution
CAUSE: The machine is set for "sort" mode.
SOLUTION: Change the machine to "group" mode. To do this,touch the "finishing" button, then select "group" and touch "OK".
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
82
bizhub 360
Solution ID
Warm-up, wrong display, incorrect operation, lock-up
TAUS0657177EN*
Solution Usage
4
Solution Usage
4
Solution Usage
4
Description
FS-510, C1104(C-1104) at power up.
Solution
CAUSE: Failed finisher control board.
SOLUTION: Replace the finsher control board (p/n 4349 0120 04).
SPECIAL NOTE : Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0703864EN*
Description
PC-402,407; C-0206 (C0206) atpower up.
Solution
CAUSE: Pinched PC-402/407 wiring harness causing the PC-402/407 control board to fail.
SOLUTION: Replace both the wiring harness (p/n 4348 6805 02) and the PC-402/407 control board (p/n 4348 0110 02).
SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0800860EN*
Description
When in the Fax/Scan mode the Direct Input tab is not displayed on the touchscreen.
Solution
PROBABLE CAUSES:
1.Manual Destination is set to Restrict.
Perform thefollowing to set Manual Destination to Allow:
a.Access Administrator Mode.
b.Select Security Settings on the touchscreen.
c.Select Security Details on the touchscreen.
d.Set Manual Destination to Allow.
Note : Please updatebizhub C451/C550/C650firmware to version GCL-E3 or greater. The latest version firmware or system software is available via the
Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and
more'.
2. Account track is enabled and the user currently logged in is restricted.
Perform thefollowing to change the user's permissions:
a. Enter Admin mode.
b. Select User Authentication Settings.
c. Select User Registration and locate the user whose permissions will be edited.
d. Select Edit
e. Select the Function Permission buttonand set Manual Destination Input to Allow.
SPECIAL NOTE : Solution contribution by Ian Lynch and Gary Scimeca, Production Print/SSD
Solution ID
TAUS0651694EN*
Solution Usage
3
Description
CLOSE > SECTION PROPERLY message with an illustration of the document feeder raised when an original is placed in the document feeder.
Solution
CAUSE: The magnet on the bottom, right, front of the document feeder is not properly aligned with the reed switch which is under the cover.
SOLUTION: Loosen the screws below the right hinge of the document feeder to align it. The document feeder manual lists this adjustment to correct
document skew so ensure that the documents do not skew after changing this adjustment. The specification for maximum skew is 3mm.
SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD
Solution ID
TAUS0801066EN*
Solution Usage
3
Description
"Insert plug-in key counter" message after key counter is installed and enabled in billing management.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
83
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
Solution
CAUSE: The wrong connector has been used to connect counter to main body.
SOLUTION: HECON® device may arrive withtwo connector types. Switch connectors. If this does not resolve issue, contact HECON® for assitance in
obtaining correct connector for specific device.
HECON® Copy Control Products are now handled exclusively bythe worldwidedistributor, High Tech Accessory Items, and bythe Canadian distributor,
Densigraphix Kopi. Information on HECON® Copy Control Products can be found on their web sites below.
Worldwide
High Tech Accessory Items
P.O. Box 7654
Rocky Mount, NC 27804
Phone: 800-541-9079
Phone: 252-937-4991
Fax: 252-937-3847
Sales: sales@hightech-ai.com
Support: support@hightech-ai.com
Web Site: www.hightech-ai.com
In Canada
Densigraphix Kopi Inc.
370 Britannia Road East, Suite 6
Mississauga, Ontario L4Z 1X9
Phone: 888-364-6273
Fax: 800-563-3192
Sales: sales@densi.com
Support: service@densi.com
Web Site: www.densi.com
SPECIAL NOTE : Solution contribution by Chuck Tripp, Production Print/SSD
Solution ID
TAUS0801838EN*
Solution Usage
3
Description
C-6101 (C6101) service code on start up. The code can be cleared by powering OFF/ON but returns. Also, the scanner unit does not initialize and the
exposure lamp does not light.
Solution
PROBABLE CAUSES:
1.The SDB (Scanner Drive Board) has failed.
Note :If the scanner is moved manually to the middle of the scanner and power is applied, the scanner never moves.
Please check that the scanner can manually be moved without binding, and if it does, replace the SCB (p/n 50GA-905 0). In some conditions the PRCB
(Printer Control Board) can also fail. If replacement of the SDB fails to resolve the issue of C-6101, then replace the PRCB (p/n 50GA 902 0E).
2. A loose screw (or similar item) isjammedon the front side of the opticscausing the optics to bind so that it is unabletoreturn home.
Remove the screw (or similar item) binding the scanner.
SPECIAL NOTE : Solution contribution by Ken Walker, Bill Hall and Mike Galletta, Workgroup/SSD and Greg Lantowski, Production Print/SSD
Solution ID
TAUS0802445EN*
Solution Usage
3
Description
When printingtheMFP will hesitate and the output is slow.
Solution
CAUSE: Incorrect settings.
SOLUTION: Perform the following setting:
1. Admin Settings.
2. Output Settings.
3. Print/Fax Output Settings.
4. Select Page Print (Batch printing should be the default).
SPECIAL NOTE : Solution contribution by Craig Blyther, ASG/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
84
bizhub 360
Solution ID
Warm-up, wrong display, incorrect operation, lock-up
TAUS0901524EN*
Solution Usage
3
Description
Code C-2403 still occurs intermittently after all code-related mnoidifications have been made.
Solution
CAUSE: Toner gets into PS28 sensor PS28 and eventually blocks the sensor and causes failure.
SOLUTION: If all modifications have been completed on the toner hopper and the code still occurs intermittantly, replace the rotation sensor PS28 (p/n
9335130061). Periodic cleaning is recommended to prevent the code from reoccuring.
SPECIAL NOTE: Solution contribution by Felix Burgen, ESS/SSD
Solution ID
TAUS0657460EN*
Solution Usage
2
Description
DF-607, the ADF original size adjustment runs properly but the machine shows A4 when 8.5x11 paper 11-inch lead edge is placed in the ADF.
Solution
CAUSE: Incorrect settings.
SOLUTION: To allow the paper size to be displayed correctly:
1. Enter the Service Mode.
2. Select System 1.
3. Select Original Size Detection.
4. Select ADF Original Size Detection.
5. Change the setting to Inch Size.
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0703610EN*
Solution Usage
2
Solution Usage
2
Description
FS-511, "Finisher full remove documents" message after 400 pages are exited to the tray during copying/printing.
Solution
CAUSE: Soft switch 15, bit 6 is set to 0 (off) -stop at 400 sheets.
SOLUTION: Change soft switch 15, bit 6 to1 (on) -not stop.
SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0800452EN*
Description
When using Vendor mode, copy jobs print out but print jobs do not.
Solution
CAUSE: Incorrect setings.
SOLUTION: Afterenabling Vendor mode,set the security settings for the function of Vendor mode. To Access the settings, use the following instructions.
"Administrator Settings" => "Security Settings" => "Function Management Settings" => "Usage Settings".
The functions of Scan, Print and Fax, as well as the settings of ON, OFF and Disabledwill be presented. Set the corresponding function (fax, print) to OFF so
that Vendor mode will ignore that function. In other words, set Print to OFF so that print jobs will be output by the MFP.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD
Solution ID
TAUS0800976EN*
Solution Usage
2
Description
The machine distorts the copies whenmultiple originals arefed through the document feeder. The problem does not occur when copying from the glass.
Solution
CAUSE: Problem with OACB (Overall Control Board).
SOLUTION: Re-flash the machine. If the problem is not resolved, replace the OACB (p/n 50GA -930 4M ) and flash the machine again.
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
85
bizhub 360
Solution ID
Warm-up, wrong display, incorrect operation, lock-up
TAUS0802011EN*
Solution Usage
2
Description
There is no duplexing selection available on the operation panel for 1:2 or 2:2.
Solution
CAUSE: Machine settings are corrupt. MFP failed to reset to default settings.
SOLUTION: To correct:
1. Access Tech Rep mode, go to State Confirm and Load check.
2. Run code 93-0.
3. Press Start. This stores the NVRAM settings that should contain the defaults.
4. Go back to System 2, Dipswitch settings, and set DIPSW31-0 to OFF, unlocking advanced output settings.
5. Go back to State Confirm, Load check and run 92-0 in the Output mode. This resets the NVRAM/Parameter Memory board to initial state.
6. Go back to System 1.
7. Reset the Marketing destination for U.S.
8. Go to Load check and run code 96-0 in the Output mode. This restores settings from 93-0 to the NVRAM.
9. Go to System 2, Dipswitch settings, and set DIPSW 31-0 to ON, locking new settings in place.
10. Back out to the basic screen and the duplex buttons should be selectable.
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0808299EN*
Solution Usage
2
Description
The Save Document key is missing under User Box menu. Flashing firmware and replacing System Control Boards all failed to resolve issue.
Solution
Cause:
The copier has been mistakenly set in one of the vending modes.
Solution:
Enter the service mode and press the "STOP" and then the"9" Key from the touch key pad. Select the Management Function choice and then make sure the
mode is set to "Unset". Power OFF and then ON the copier. The Save Document Key should have returned.
Note:
If the vending mode is enabled, it should be noted that there are limitations in function based on the modes used. To verify simply disable vending to see if
function returns.
SPECIAL NOTE: Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0808413EN*
Solution Usage
2
Solution Usage
2
Description
Copies jam when duplexing.
Solution
CAUSE: Actuator came out/installed incorrectly. Customer could have reinstalled it backwards.
SOLUTION: Remove actuator (p/n 4030 3818 02) and torsion spring (p/n 4030 3819 01) and snap it back in correctly.
SPECIAL NOTE: Solution contribution by John Miller, Workgroup/SSD
Solution ID
TAUS0900110EN*
Description
C-2402 (C2402) code at power up after reseating and cleaning the drum carriage.
Solution
CAUSE: The erase lamp (EL) connector on the drum carriage is disconnected.
SOLUTION: Reconnect the erase lamp (EL) in the drum carriage.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
86
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
SPECIAL NOTE : Solution contribution by Mark D'Attilio and Ian Lynch, Production Print/SSD
Solution ID
TAUS0900206EN*
Solution Usage
2
Solution Usage
1
Description
The machine displays "Enter serial number."
Solution
CAUSE: Missing data in the Service mode.
SOLUTION: To resolve this problem, perform the following:
1. Enter the Service mode.
2. Select System 1.
3. Select Serial Number.
4. Select Printer (body).
5. Enter the correct serial number of the machine and press OK.
6. Press End, then exit the Service mode.
SPECIAL NOTE : Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0701186EN*
Description
Error code C0000 (C-0000).
Solution
PROBABLE CAUSES:
1. Pinched or damaged wiring between OACB and the LDB or INDEXB.
Inspect wiring from connectors 50 and 51 of OACB. If damaged wiring is found replace wiring harness (p/n 50GA 9020 0).
2.Failed or corruptNVRAM.
Please replace the NVRAM (p/n 50GA-9111). Follow the procedure in attached Bulletin Number5783.To viewthe PDF, Adobe Reader® must be installed.
Adobe Reader® can be downloaded for free from the Adobe® web site at: http://www.adobe.com/products/acrobat/readstep2.html .
3. There is no firmware on the PRCB.
Note : This usually occurs after replacing the Printer Control Board (PRCB).
Install firmware on the PRCB.The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from
SSD Web Support (CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
SPECIAL NOTE : Solution contribution by Jim Behrends and Chuck Tripp, Production Print/SSD
Solution ID
TAUS0800377EN*
Solution Usage
1
Description
Option setting for the HDD enabled in the service mode, yet in State Confirmation, Memory HDD Check, and Management list, the option for HDD is
unavailable.
Solution
CAUSE: Incorrect configuration.
SOLUTION:Enter the Service mode, select System 2, DIPSW Settings and set DIPSW 19, bit 3 fromON to OFF. Reformat the HDDin the State Confirmation
Memory and HDD adjust mode.
SPECIAL NOTE : Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0801123EN*
Solution Usage
1
Description
C-8200 (C8200) code only in the morning.
Solution
CAUSE: Failing NVRAM.
Note : If firmware was update recently and then the problem started.
SOLUTION: Replace NVRAM from known working machine. If it does not register anerror in the morning, open a ticket and state that a test was
conductedwhich had positive results.
Provide all information in the ticket: serial number, meter reading and firmware version; also if it was just updated.
Then contact the SSD Hotline or checkany web submissionsto see if SSD approved a replacement NVRAM. If approval has been provide, thenprovide the
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
87
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
ticket number to the parts person so they can order via the Logistics site via KMBS web.
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0801457EN*
Solution Usage
1
Description
When printing from AS/400®, the writer fails when printer runs out of paper.
Solution
CAUSE:The writer on the AS/400® will stop the print job when it receives a paper out signal, if the paper out signal is not cleared by adding more paper then
the network connection to the printer is terminated by the MFP.
SOLUTION:Increasing the Network timeout on the MFP corrects the issue.To set the Network timeout use the following procedure:
Most MFPs:
1. Press the utility button and go into Administrator settings => enter the password.
2. Go to Printer settings and then Network timeout set it to 300 seconds.
bizhub PRO 1050:
1. Press Machine button on the LCD, then the Controller button => Interface setting and then Network Timeout.
2.Set 300 seconds and press the SET button.
bizhub PRO 920:
1. Press the utility button and then the controller button on the LCD.
2.Select the Interface setting => Network setting.
3. Enter 300 seconds and press the SET button.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS/SSD
Solution ID
TAUS0801919EN*
Solution Usage
1
Solution Usage
1
Solution Usage
1
Description
When replacing FRUs, it is necessary to reset the counter for that particular FRU. In some firmware versions, the button is missing.
Solution
CAUSE:The dipswitch that controls the button is set toOFF during firmware updates.
SOLUTION:Pleaseset dipswitch11-7 to ON.
SPECIAL NOTE : Solution contribution by Paul Santangelo, ESS
Solution ID
TAUS0801954EN*
Description
Intermittently getting fax TX deleted due to error: Protocol error.
Solution
CAUSE: Incorrect type of connection to phone line. A 4-conductor wire was used to connect the machine to the phone jack.
SOLUTION: Use a 2-wire line to connect the machine to the phone jack.
SPECIAL NOTE : Solution contribution by Bill Berkhahn -Central Office Systems.
Solution ID
TAUS0802356EN*
Description
J97-02 codewhen attempting to duplex.
Solution
CAUSE: The ADU wiring harness is worn.
SOLUTION:Replace the ADU wiring harness (p/n 50GA90171).
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
88
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
SPECIAL NOTE : Solution contribution by Tom Kelly, Workgroup/SSD
Solution ID
TAUS0802699EN*
Solution Usage
1
Solution Usage
1
Solution Usage
1
Description
How to change Sleep/Power Save/Low Power mode.
Solution
Use this procedure to set the sleep, low power and power save mode.
1. Press the Utility/Counter key.
2. Select Administrator Settings.
3. Enter the Password (12345678).
4. SelectSystem Settings.
5. Select Power Save Settings.
6. Press“C” on the key pad.
7.Use the key pad to change settings.
8. Press OK and back out of the menu.
SPECIAL NOTE: Solution contribution by Marge McLea, Production Customer Support/SSD
Solution ID
TAUS0808028EN*
Description
The machine has a C670 code. The CCD assembly has been replaced.
Solution
Cause:
Defective OACB.
Solution:
Please re-flash the machine. If the problem is not resolved replace the OACB (p/n 50GA -930 4M).
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0808140EN*
Description
PROBLEM:
The copier is indicating a C3502 code on start up.
Solution
CAUSE:
This issue is caused by an over temperature condition of the lower fusing roller. This may be due to a failed thermister TH2, Failed PRCB, or DCPS.
SOLUTION:
To resolve the code proceed through the following steps:
Begin by cleaning the TH2 sensor and then clearing the code. To clear the code, hold the utility key down while powering on the copier.
Select the trouble reset screen.
After selecting trouble reset, select STOP, 0, STOP, 0,1 and enter the service mode.
Select System 2
Select DIPSW settings and set DIPSW3, bit 1 from a 1 to a 0.
Power OFF and then ON the copier.
If the code should return after reseting it, replace the TH2 (p/n 50GA-5440).
If the issue still is unresolved replace the PRCB (p/n 50GA-9020E).
Finally if the issue still is unresolved the DCPS (p/n 50GA-8451 01) should be replaced.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
89
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
SPECIAL NOTE: Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0808287EN*
Solution Usage
1
Solution Usage
1
Solution Usage
1
Solution Usage
1
Description
Problem:
The machine is printing blank copies and the drum rotation has been checked in the load mode.
Solution
Cause:
The drum may not spin under normal load and yet it will spin in load mode.
Solution:
Please try replacing the Drum Coupling Plate (p/n 50GA-1550).
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0808621EN*
Description
C-0206 at power up.
Solution
Cause:
Opens in the harness connected to the PWB-H in the PC-402 or PC-407.
Solution:
Please check the harness for any damage.
Replace the PWB-H harness assembly as needed (p/n 4479 0105 03)
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0900250EN*
Description
DF-607/DF-613, matching paper size is not available.
Solution
CAUSE: Incorrect settings.
SOLUTION: To program for matching paper size:
1. Enter Service Mode.
2. Touch ADF.
3. Select Original Size Adj.
4. Set the original scale to max. Set to A3 mark on scale and press Start. OK should be displayed.
5. Set the original scan to min. Set to B6 mark on scale and press Start. OK should be displayed.
6. Press End and exit.
Note : There are two marks on top of the paper tray itself that should be used for the adjustment.
SPECIAL NOTE : Solution contribution by Malcolm Hibbert, Workgroup/SSD
Solution ID
TAUS0900259EN*
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
90
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
Description
C-2701 is displayed at power on.The suggestions in the Service Manual have not resolved the problem.
Solution
CAUSE:If thecomponents cited in the Service Manual (Charging corona, High voltage unit, and Printer control board) have not resolved the problem the
cause could be poor contact with the drum unit.
SOLUTION:Check drum unit contacts and clean if necessary.
SPECIAL NOTE : Solution contribution by Kevin Fortner, Novacopy.
Solution ID
TAUS0900309EN*
Solution Usage
1
Solution Usage
1
Description
Problem:
CD202 after flashing the machine firmware.
Solution
Cause:
Loose connection.
Solution:
Please reseat the memory board on the OACB CN35.
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0901283EN*
Description
Intermittently from glass, copies are flipping 90 degrees.
Solution
Cause: DIPSW settings have been set incorrectly. This causes the output to flip 90 degrees.
Solution: Please set and verify the copiers current DIPSW setting under the Service mode, System 2, Soft Switch Setting mode. Check DIPSW 22-6 (Image
rotation) which should be set to 1 (not rotate). Also checked DIPSW 25-6 (image rotation when stapling) which should be set at 0 (not rotate).
SPECIAL NOTE: Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0901305EN*
Solution Usage
1
Solution Usage
1
Description
Constant J-3100 code while copying (simplex/duplex), also the copies output are wavy.
Solution
Cause: Fixing Idling Gear B 15T failure.
Solution: Replace the Fixing Idling Gear B 15T Gear (P/N: 50GA54700)
Contributor name: Jonah Mattox, GLOBAL IMAGING SYSTEMS, INC.
Solution ID
TAUS0901871EN*
Description
Legal (8.5 X 14) paper is not recognized from any tray. Tray reads as "???".
Solution
CAUSE: Machine's marketing area has erroneous data.
SOLUTION: Set the Marketing area in service mode to Europe then back to US to set the marketing area correctly.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
91
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD
Solution ID
TAUS0701185EN*
Solution Usage
0
Solution Usage
0
Description
C-D202 (CD202).
Solution
CAUSE: Insufficient memory.
SOLUTION: Please install 128MB memory (p/n U226-0250) in the slot.
SPECIAL NOTE : Solution contribution by Malcolm Hibbert, Workgroup/SSD
Solution ID
TAUS0703351EN*
Description
C-0206 code is intermittently displayed.
Solution
CAUSE: Paper lift motor (M5)(p/n 4348075201)is not driving when paper runs out of the primary paper tray.
SOLUTION: Recommend adding a stack of paper to be shifted and one sheet in feed. Make several copies and see if the code comes back and if the paper
is shifted properly. If the paper is not shifted, the PCCB (p/n 4348-0110-02) has failed and needs to be replaced.
SPECIAL NOTE: Solution contribution by Ken Walker, Workgroup/SSD, SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD
Solution ID
TAUS0800881EN*
Solution Usage
0
Solution Usage
0
Description
Unable to PING after replacing the OACB,moving the IC-204 from original board and also the NVRAM.
Solution
CAUSE: Loose connections on the OACB (p/n 50GA 9303) and IC-204 or the NVRAM.
SOLUTION: Remove power from wall and reseat all of the OACBconnectors including the NVRAM and the IC-204 chip.
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0802192EN*
Description
In the Job List screen the "Increase Priority" button is not available.
Solution
CAUSE: Key counter is installed.
SOLUTION: According to specifications, this function is not compatible with key counters.
Note : If no key counter is installed, verify that the Administrator Setting/System Setting/Restrict User Access/Restrict Access to Job Settings/Changing Job
Priority is set to "Allow."
SPECIAL NOTE: Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0808278EN*
Solution Usage
0
Description
PROBLEM:
MFP locking up, unable to delete job injob list.
Solution
CAUSE:
Corrupt or damaged OACB.
SOLUTION:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
92
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
Replace OACB (p/n 50GA-9303K).
SPECIAL NOTE: Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0703057EN*
Solution Usage
Description
With a Jamex© Vending System attached to the MFP, print jobs do not print and this is even occurring when the unit is in Vending mode (coins inserted).
Solution
CAUSE: When theMFP is in the vending mode the printing functionsare disabled by default. Pass-through Printing must be enabled.
SOLUTION: To enable Pass-through Printing:
1.Enter the Service mode.
2.System 2 mode.
3.Select the Soft Switch Setting Mode and change DipSW 22, bit number 3 to ON.
SPECIAL NOTE : Solution contribution by Cesar Jimenez, Production Print/SSD
Solution ID
TAUS0703312EN*
Solution Usage
Description
When direct input to scan to E-mail is restricted the "Check Connection" button during LDAP setup disappears.
Solution
CAUSE: Firmware upgrade required or incorrect settings.
SOLUTION:Make sure the firmware is at 31_GUP level or greater.
Set the LDAP server settings before restricting the direct input to scan to E-mail.The "Check Connection" button is available when the the direct input is not
restricted.
Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
SPECIAL NOTE : Solution contribution by Mahen Shukla, ESS/SSD
Solution ID
TAUS0703350EN*
Solution Usage
Description
No power. Fan motors and LEDs are not working at all.
Solution
CAUSE: DCPS1 failed.
SOLUTION: Please check that there is supply voltage of 120V AC being supplied to theMFP via the power cord. If there is and there are no fans or board
LEDs the DCPS should be replaced (p/n 50GA84510).
SPECIAL NOTE : Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0800110EN*
Solution Usage
Description
When creating a scan to E-mail one-touch button, able to see it on admin in the web, but not showing up on the scan button at machine.
Solution
CAUSE: The scan to E-mail setting is restricted.
SOLUTION: Access the Admin mode on machine =>go to Network => select E-mail Setting, then E-mail TX =>select Scan to E-mail then highlight
Allow.
SPECIAL NOTE : Solution contribution by Don St. Onge, Workgroup/SSD
Solution ID
TAUS0808086EN*
Solution Usage
Description
Unable to see controller after installing the IC-204 controller option. Is there a DIPSW or other setting that needs to be set to enable the print controller?
Solution
Cause:
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
93
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
There are no settings that need to be set to enable the print controler IC-204. However, if the serial number for the main body or if the marketing are is
improperly set under the service mode, System 1 setting mode then the controler will njot be indicated.
Solution:
Please verify the correct serial number has been added and the marketing area for the main body is set for US. This is done under the Service mode, System
1 setting Mode, Serial number & Marketing area setting modes.
Note: If the settings keep changing to Japan marketing area or the serial number clears, the NVRAM may need to be replaced.
SPECIAL NOTE: Solution contribution by Ken Walker, Workgroup/SSD
Solution ID
TAUS0808254EN*
Solution Usage
Description
Problem:
User authentication will not turn off. The customer has decided not to use it and it will not turn off.
Solution
Cause:
File corruption on the HDD.
Solution:
Please format the HDD. Do a Physical and then a Logical format.
Enter service mode.
Select State Confirmation.
Select Memory/HDD Adjustment.
Select HDD format.
Select All and hit yes.
SPECIAL NOTE: Solution contribution by David Silverstein, Workgroup/SSD
Solution ID
TAUS0900261EN*
Solution Usage
Description
"Insert plug-in counter" indication when the function is already enabled.
Solution
CAUSE: Incorrect configuration.
SOLUTION: To correct:
1. Remove the top, right-side cover on the scanner unit.
2. Find the 4-pin connector and remove the loopback connector.
3. Insert the correct harness to the connector for the specified device.
SPECIAL NOTE : Solution contribution by Malcolm Hibbert, Workgroup/SSD
Solution ID
TAUS0900742EN*
Solution Usage
Description
Image Shift does not function when using Page Scope Direct Print
Solution
CAUSE: This functionality is within specificaton.
SOLUTION:Image shift is not designed tofunction under PageScope Direct Print (PSDP).
SPECIAL NOTE: Solution contribution by Craig Blyther, ASG/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
94
bizhub 360
Solution ID
Warm-up, wrong display, incorrect operation, lock-up
TAUS0900897EN*
Solution Usage
Description
Image Shift is not functioning when using PageScope Direct Print.
Solution
CAUSE: Machine limitation based on firmware.
SOLUTION: No update to the firmware is planned. The firmware is outdated, therefore the Image Shift function via PageScope Direct Print (PSDP) does not
work and the firmware is unable to be modified.
SPECIAL NOTE : Solution contribution by Craig Blyther, ASG/SSD
Solution ID
TAUS0901151EN*
Solution Usage
Description
Printing does not work. The machine responds to PING and the IC-204 chip has been replaced. The Authentication and Copier Setting buttons do not appear
in the administrator mode. User Authentication/Account Track is not enabled and there is no key counter.
Solution
CAUSE: Incorrect billing setting mode.
SOLUTION: Enter the service mode and then press Stop-9. Select Management Function Choice and then select Unset. Exit the service mode.
SPECIAL NOTE: Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0901359EN*
Solution Usage
Description
The web page doesn't display.
Solution
CAUSE: The logic is scrambled and must be re-initialized.
SOLUTION:
1. Enter Service Mode.
2. Touch Initialization.
3. Touch System 1.
4. Touch Network Setting Data.
5. Press the Start key and exit the Service Mode when the procedure is completed.
6. Power cycle the unit.
SPECIAL NOTE: Solution contribution by Malcolm Hibbert, Workgroup/SSD, SPECIAL NOTE: Solution contribution by Bill Hall, Workgroup/SSD
Solution ID
TAUS0901600EN*
Solution Usage
Description
Why can’t the Vendor 1 key be selected in Service Mode?
Solution
The Vendor 1 key can't be selected in Service Mode if Account Track has been turned on. When Account Track has been turned on, none of the selections
under Management Function Choice in Service Mode can be made. Please turn Account Track Off to allow the selections under Management Function
Choice to be made available.
SPECIAL NOTE: Solution contribution by Dave Bruni, Workgroup/SSD
Solution ID
TAUS0901865EN*
Solution Usage
Description
When trying to carry out the ADF Density Adjustment why does the Start key stay amber?
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
95
bizhub 360
Warm-up, wrong display, incorrect operation, lock-up
Solution
The Start key may stay amber when trying to carry out the ADF Density Adjustment if the ADF Original Size Detection is not set to Full Size. The ADF
Original Size Detection can be changed using the following steps:
1) Enter Service Mode
2) Select System 1
3) Select Original Size Detection
4) Choose ADF Orig Size Detection
5) Select Full Size
The ADF Density Adjustment can now be carried out. Upon completion of the adjustment please go back in and set the ADF Original Size Detection to its
prior setting.
SPECIAL NOTE: Solution contribution by Dave Bruni, Workgroup/SSD
Solution ID
TAUS0902194EN*
Solution Usage
Description
After replacing the HDD, the MFP won't recognize even after setting the HDD in service mode. Unable to see any functions for the HDD. Option status may
show HDD installed.
Solution
CAUSE: Incorrect setting.
SOLUTION: Go into service mode under DipSW 19-3 and make sure that it is selected to "0".
SPECIAL NOTE: Solution contribution by John Miller, Workgroup/SSD
Solution ID
TAUS0902514EN*
Solution Usage
Description
Copy sets are limited when copying.
Solution
CAUSE: Incorrect dipSW settings.
SOLUTION: Set dipSW [9-0 to 9-3] to 0 for each setting to enable unlimited copy sets when copying.
SPECIAL NOTE: Solution contribution by Jim Behrends, Workgroup/SSD
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
96
bizhub 360
Solution ID
TAUS0701872EN*
Solution Usage
9
Description
When a large job (in excess of 50 pages) is being scanned and a print job is sent, as the document is in scan process, the machine may lock up. Immediate
recovery can be achieved by powering the machine OFF/ON.
Solution
CAUSE: Firmware upgrade required.
SOLUTION: Upgrade the firmwareto minimum version 31_GUP (34.38MB).
Note : The latest version firmware or system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
Solution ID
TAUS0701984EN*
Solution Usage
8
Solution Usage
6
Description
Possible error codes during TCR adjustment.
Solution
The following errors mightbeindicated on the displayduring the TCR adjustment:
Error
Cause
Action
Error 3
When the output ripple voltage of the TDS(Toner Density Sensor) is less than 0.5V at the end of TCR adjustment.
TCR sensor abnormality -> Replace TCR sensor
Printer control board abnormality -> Replace board
Error 4
When the output ripple voltage of the TCR sensor is less than 0.02V
Connector contact failure -> Check connection
TCR sensor abnormality -> Replace TCR sensor
Printer control board abnormality -> Replace board
Error 5
When the TCR adjustment voltage is out of from 6.2V to 7.6V
TCR sensor adjustment failure -> Replace TCR sensor
Error 6
A/D conversion error of TCSB(Toner sensor control board) output signal
Dirt of IDC sensor -> Clean up the IDC sensor
Printer control board abnormality -> Replace board
SPECIAL NOTE : Solution contribution byKonica Minolta Europe.
Solution ID
TAUS0700426EN*
Description
Some gray half-tones/shading are not rendered as expected.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
97
bizhub 360
Solution
CAUSE: The Gamma setting for density is a specification limit.
SOLUTION:A possible work-around includes the following adjustments:
1. Laser Diameter Adjustment.
2. Toner Density Adjustment.
If the above adjustments do not provide suffficient improvement, new firmware is available on the SSD Download Selector Search Page.
bizhub 750/600
DLBT0701047EN00
bizhub 500
DLBT0701060EN00
bizhub 420
DLBT0701061EN00
bizhub 360
DLBT0701062EN00
Notes :
1. Refer the Service Manual for the adjustment procedures.
2. Try the Laser Diameter adjustmentfirst, and if the customer is still not satisfied, try the Toner Density adjustment.
3. The above-referenced DLBTs are attached.
4. To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0702322EN*
Solution Usage
6
Description
After installing the print driver (PCL or PostScript) on Microsoft® Windows Vista™, the User Authentication/Account Track selection is unavailable.
Solution
To enable User Authentication/Account Track in the print driver, perform the following:
1. Enter the Printer Properties of the driver.
2. Select the Configure tab.
3. Under Device Option, select the desired mode (User Authenticationor Account Track).
4. Enable the option in the drop down below Device Option.
5. Select Apply.
6. Verify that User Authentication/Account Track is available.
Solution ID
TAUS0701326EN*
Solution Usage
4
Description
J13, J16-01, or various J30 codesduring nonsor t copying or printing
Solution
CAUSE: Finisher timing is off, caused by grease applied to the one-way gears (p/n 14GR77170 and 14GR45810) located behind the finisher jam removal
knob FN6.
SOLUTION: Clean the gears with alcohol, or replace them.
Solution ID
TAUS0701765EN*
Solution Usage
4
Solution Usage
3
Description
Is the System Control Board (OACB) the same for all these models?
Solution
The System Control Board (p/n 50GA-9303K) is the same for the listed models.
Solution ID
TAUS0701952EN*
Description
Cannot connect to the network after installing a new NVRAM chip.
Solution
CAUSE: Setting needs to be changed.
SOLUTION: To activate the network after installing a new NVRAM chip, perform the following:
1.Disable the network (Admin. Mode/Network Settings/Network Settings/Off)and power the machineOFF with the main switch.
2.Power ONthe machine and enable the network.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
98
bizhub 360
Solution ID
TAUS0702483EN*
Solution Usage
3
Description
Setting SNMP v1/v2c “read/write community” names through PageScope Net Care.
Solution
Changing the read and/or write SNMP "community names" can be implemented as a security measure through PageScope Net Care. Please see attached
document for instructions.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0702659EN*
Solution Usage
3
Description
In the event that an issue arises that requires immediate action by the technician, certain NVRAMs may be exchanged/swapped between units due to their
compatibility with other models.
Solution
The following groupings of main bodies are compatible for NVRAM exchange with others within their group only in emergency situations or for
troubleshooting purposes :
7145/7222/7228/7235
bizhub 200/250/350
bizhub 360/420/500
bizhub 600/750
7155/7165/7085
7210/7255/7272/bizhub PRO 920/bizhub PRO 1050
C250/C252/C300/C351/C352/C450
C451/C550/C650
IMPORTANT : A new NVRAM should be obtained as soon as possible for the machine requiring one.
Notes :
1. The bizhub C350 NVRAM may only be used between other bizhub C350s.
2. CAUTION : The bizhub PRO C500/8050 NVRAMs may not be exchanged between units due to the serialization of the NVRAM.
SPECIAL NOTE : Solution contribution by Ed Bellone, Production Print/SSD
Solution ID
TAUS0800977EN*
Solution Usage
3
Description
Font Management Utility.
Solution
The latest Font Management Utility can be downloaded viathe Konica Minolta Download Selector. Access the Selector from SSD Web Support (CS Expert
Support) by clicking on 'Download MSDS, Drivers, Firmware and more'. Pleaserefer to the attached ReadMe prior to installation.
The attached Font Management Utility User's Guide covers the following:
Selecting and adding devices
Add/Delete Mode
Add Collectively Mode
Delete Collectively Mode
Font/form list settings file
Saving lists as files
Note : To viewthe PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html .
Solution ID
TAUS0634060EN*
Solution Usage
2
Description
List of equipment that is no longer being supported.
Solution
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
99
bizhub 360
Please see attached Product & Technical Support Bulletins 1792 and 2443 andMarketing Bulletin#07-GB-016.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0701113EN*
Solution Usage
2
Description
Procedure for upgrading to Phase 3.0, version 30 firmware and above.
Solution
Before upgrading to Phase 3.0, the machine must be at Phase 2.0, version 20 or higher. Once at version 20, machines can be upgraded directly to the
highest level with no interim steps.
Note : The latest version firmware and system software is available via the Konica Minolta Download Selector. Access the Selector from SSD Web Support
(CS Expert Support) by clicking on 'Download MSDS, Drivers, Firmware and more'.
Solution ID
TAUS0701471EN*
Solution Usage
2
Solution Usage
2
Solution Usage
2
Description
Who to contact for parts and technical supportconcerning Jamex™ products.
Solution
Support is provided by Jamex™ by calling 800-289-6550. Refer to attached Marketing Bulletin #04-GB-016 for more detail.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0701809EN*
Description
Data light remains lit.
Solution
CAUSE: The HDD option is set to installed, when HDD is not installed.
SOLUTION: Verify that there is no HDD physically installed. Check option setting. Enter Tech Rep mode and select:
1. System 2.
2. Option.
3. HDD confirm Not Installed.
Solution ID
TAUS0701964EN*
Description
When searching solutions by models,referenced links for the documentsare notaccessible.
Solution
CAUSE: This is a search of the printed database. The links are locatedwithin the solution in the database.
SOLUTION: Copy the solution ID number into the Knowledgebase look-up Keyword field and select Search to access the solution complete with active links
to attached documents.
Note : If there is an actual 'dead' link within the solution, please send an E-mail to cses@kmbs.konicaminolta.us with the solution ID number and please
identify the link.
Solution ID
TAUS0702545EN*
Solution Usage
2
Solution Usage
1
Description
Part number for the 128MB SODIMM on the OACB.
Solution
The 128MB SODIMM on the OACB (p/n U226-0250).
Solution ID
TAUS0651562EN*
Description
Microsoft®-certified printer drivers - PCL, PostScript, PostScript (P)and PostScript (V).
Solution
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
100
bizhub 360
The Konica Minolta Microsoft®-certified printer driverscan bedownloaded fromthe Konica Minolta Download Selector. Access the Selector from theKMBS
public site ( http://www.kmbs.konicaminolta.us ) Support & Drivers tab or from SSD Web Support (CS Expert Support) by clicking on 'Download MSDS,
Drivers, Firmware and more'.
These drivers will be shown as a WHQL ( W indows H ardware Q uality L abs)Download.
Access the Download Selector and type WHQL in [Find downloads:],then click on Search->.
Solution ID
TAUS0654011EN*
Solution Usage
1
Solution Usage
1
Solution Usage
1
Description
After making copy settings they revert to initial settings when the original is placed on the document feeder (ADF).
Solution
CAUSE: Incorrect user setting.
SOLUTION: To correct the setting, perform the following:
1. Press the Utility/Counter key.
2. Select User Setting.
3. Select Reset Setting.
4. Select Job Reset.
5. Select When original is set on ADF.
6. Change setting to Do not reset.
7. Exit.
Solution ID
TAUS0700244EN*
Description
How to determine what version of Sun Java™ is installed on a Microsoft® Windows workstation.
Solution
To determine what version of Sun Java™ is installed, perform the following:
1. From a command prompt type:java -version
2. Press Enter.
3. The version of Sun Java™ will be indicated. If the command is not recognized then Sun Java™ is not installed.
Solution ID
TAUS0702303EN*
Description
Constant jamming from trays 1 and 2. Operation panel also indicates "Please load paper" and "Tray does have paper". Machine can be reset by opening and
closing the paper feed trays.
Solution
CAUSE: Bent paper feed sensor and lift motor assembly at the frame mount right side of the unit next to the paper lift motor.
SOLUTION: Carefully re-form mounting plate to bring sensors and contacts into position.
Solution ID
TAUS0702496EN*
Solution Usage
1
Solution Usage
1
Description
DF-607, J-6101 and a grinding noise. No feed from ADF.
Solution
CAUSE: The rear gear on the undersideof the ADFcover is not aligned with the drive gear. The gear mounting plate is damaged.
SOLUTION: Re-form the gear mounting plate.
Solution ID
TAUS0702538EN*
Description
FS-508/FS-510, elevatordrives down (or crashes down) to the bottom of the finisher when using the MT-501 or SD-502.
Solution
CAUSE:Damagedworm gear and gearon thedrive section of the elevator lift. The worm gear (Pulley 29T - p/n 4611 4609 01) cannot drive the gear ( Gear
16/42T - p/n 4349 2053 01) to lift up the elevator. The reasonfor the damageis little or no grease between the cog of the gears and between the shaft and
the worm gear (see attached photo - Pulley Failure).
SOLUTION:Replace the damaged gear(s). Please apply additional lubrication to these areaswhen installing theMT-501 or SD-502. Recommended g rease
type is MOLYKOTE® EM-50L (p/n 4478 7801 01) . Attached is the MOLYKOTE® EM-50L MSDS and Product Information sheet.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
101
bizhub 360
Notes :
1. The grease can probably be purchased locally or via the Internet if not in parts stock.
2. For reference, pleasesee the attached pages from the FS-508/FS-510 Parts Guide Manual.
3.To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
SPECIAL NOTE : Solution contribution byKMBT (Japan).
Solution ID
TAUS0702737EN*
Solution Usage
1
Solution Usage
1
Solution Usage
0
Description
The Scan key no longer responds. The control panel has been replaced and the machine has been re-flashed.
Solution
CAUSE: SCB failure.
SOLUTION: Replace the System Control Board (p/n 50GA-9303K).
Solution ID
TAUS0702888EN*
Description
How to print to a printer on a Microsoft® Windows XP PC from a Macintosh® running OS version 10.4.x.
Solution
Please perfrom the step-by-step procedure mentioned in the attached document.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0700750EN*
Description
Why is the image rotated 180 degrees when the staple mode is selectedor on the first job, after reloading paper in the 1st or 2nd cassette?
Solution
Firmware requires updating. Please install version 30 or later firmware.
To prevent the image from being rotated 180 degrees when using the staple mode set DipSwitch 25-6 to 1 (ON). This DipSwitch setting was made available
with version 30firmware.The DipSwitch can be changed using the following steps:
1. Enter the Service Mode.
2. Select System 2.
3. Select Dip Switch Setting.
4. For Switch Number, enter 25.
5. For Bit Number, enter 6.
6. Choose ON.
7. Touch Set.
8. Touch OK.
Note : As a workaround, change the "Original Direction Setting" under the "Combine Original Mode" to the same direction in the cassette tray then set the
machine settings to Current Setting.
Solution ID
TAUS0701645EN*
Solution Usage
0
Description
"Please wait" message when any button is pressed in the Service Mode.
Solution
CAUSE: Trouble reset is necessary.
SOLUTION: Reset the machine and enter the Service Mode by performing the following:
1.Power the machine OFF.
2. Press and continue to hold the Utility/Counter button.
3.Power the machine ON. The Utility/Counter button can be released when the Konica Minolta logo appears.
4.Press the Trouble Reset button when it appears.
5. Press Stop - 0 - 0 - Stop - 0 - 1 to enter the Service Mode. Individual buttons in the Service Mode should now function properly.
Solution ID
TAUS0655608EN*
Solution Usage
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
102
bizhub 360
Description
Are Konica Minolta MFPs compatible with Category 6 cable standard?
Solution
Konica Minolta MFPs are fully compatible with Category 6 cable standard.
Category 6 cable is a cable standard for Gigabit Ethernet and other network protocols that is backward compatible with the Category 5/5e and Category 3
cable standards.
Cat-6 features more stringent specifications for crosstalk and system noise. The cable standard is suitable for 10BASE-T/100BASE-TX and 1000BASE-T
(Gigabit Ethernet) connections and it provides performance of up to 250MHz.
Solution ID
TAUS0700664EN*
Solution Usage
Description
Unable to access MFP with Phase 3 firmware using PageScope Data Administrator.
Solution
CAUSE: Early version of PageScope Data Administrator is installed.
SOLUTION:Install version 3.03 or later.
Solution ID
TAUS0700985EN*
Solution Usage
Description
IC-204 User's Guide.
Solution
Refer to the attached PDF (13MB).
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0700986EN*
Solution Usage
Description
User's Guides for the bizhub 360.
Solution
Refer to the attached PDFs Box Operations (5.55MB)
FK-502 Facsimile Operations (13MB)
Network Fax Operations (8.83MB)
Network Scanner Operations (12.4MB)
Enlarge Display Operations (2.11MB)
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0700987EN*
Solution Usage
Description
The bizhub 500/420/360 Troubleshooting Guide.
Solution
Refer to the attached PDF.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0701357EN*
Solution Usage
Description
Offset does not work with the FS110.
Solution
CAUSE:Vendor mode is enabled.
SOLUTION: Disable Vendor mode.
Note: Offset does not work withM ailbins and Saddle Stitch.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
103
bizhub 360
Solution ID
TAUS0701724EN*
Solution Usage
Description
How to enter Tech. Rep mode.
Solution
To enter Tech. Rep mode, perform the following:
1. Press Utility/Counter.
2. Select [Details].
3. Press Stop 00, Stop 01.
4. Enter the 8-digit service code (default 00000000) and press [END].
Solution ID
TAUS0701738EN*
Solution Usage
Description
How to adjust the sensitivity for the LCD?
Solution
To adjust the sensitivity on the LCD, perform the following:
1. Press the [Accessibility] button on the control panel.
2. Touch the [Touch Panel Adj.] on the LCD.
3. Using a fine point pen or pencil touch the crosshairs.
Solution ID
TAUS0701739EN*
Solution Usage
Description
How to change the file name for Scan to E-mail and SMB from the control panel?
Solution
To change the scan file name, peform the following:
1. Press [Scan] button.
2. Touch [Address Book].
3. Select the destination button.
4. Press [Scan Setting] to change scanner setting and press OK.
5. Press the [Mode Check].
6. Touch [E-mail Setting] in lower left hand corner.
7. Touch [Filename] button.
8. Press the delete key until the default file name is erase.
9. Enter the new file name and press OK.
10. Press [Start] to scan the document.
Solution ID
TAUS0702146EN*
Solution Usage
Description
How to perform Print Screens (screen shots) from a Microsoft® Windows OS and Macintosh® OS.
Solution
Please see the attacheddocument for detailed information.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0702289EN*
Solution Usage
Description
When faxing, the communication error list prints from the 8.5x14 tray by default.
Solution
CAUSE:Incorrect settings.
SOLUTION: Perform the following steps:
1. Press Utility.
2. Press User settings.
3. Press System settings.
4. Press Paper tray settings.
5. Press Print list and select the paper size/trayfrom whichthe reportshould feed.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
104
bizhub 360
Solution ID
TAUS0702623EN*
Solution Usage
Description
How to get the platen to scan 11x17 and ignore the size detection.
Solution
To get the platen to scan 11x17 and ignore the size detection, perform the following:
1. Please select the Application tab.
2. Touch the Image Adjust button.
3. Touch the Standard Size button.
4. Select 11x17.
5. Go back to thecopymenu and select Zoom.
6. Select 11x17 => Letter.
7. Go back to the copy menu.
8. Select paper and select the desired paper tray.
9. Make a test copy. It should work without cutting anything off.
Note : The machine will now scan the platen the full size of 11x17 and reduce it to fit on letter paper. The size detection sensors will be ignored.
Solution ID
TAUS0702741EN*
Solution Usage
Description
Does theFK-502 support U.S. Air Force AFI 33-202, Volume 1, Facsimile Class 1 protocol requirement?
Solution
The FK-502 specificationdoes not support the U.S. Air Force AFI 33-202, Volume 1, Facsimile Class 1 protocol requirement.
Solution ID
TAUS0702890EN*
Solution Usage
Description
Printing to a Windows Samba shared printer from a Macintosh®.
Solution
Please perfrom the step-by-step procedure mentioned in the attached document.
Note : To view a PDF, Adobe Reader® must be installed. Adobe Reader® can be downloaded for free from the Adobe® web site at:
http://www.adobe.com/products/acrobat/readstep2.html
Solution ID
TAUS0703002EN*
Solution Usage
Description
How to set Fax Forward to default to PDF.
Solution
To set Fax Forward to default to PDF:
1. Select the FAX button.
2.Select the Scan Setting on the LCD.
3. Select the File Type as PDF.
The followingmakes the setting permanent:
1. Select the Utility button.
2.Select User Setting.
3.Select Initial Setting.
4.If the setting is set for Factory, change it to Current.
Copyright 2009, Konica Minolta Business Solutions U.S.A., Inc.
October 2009
105
Download PDF