311019M,LineLazer 3400, FieldLazer S200 Airless Line Striper

Repair
LineLazer™3400, FieldLazer S200
Airless Line Striper
311019M
EN
- For the application of line striping materials. For professional use
only. Not for use in explosive atmospheres.Important Safety Instructions
Read all warnings and instructions in this
manual and in your gun manual. Save all
instructions.
Models: 248861, 249007, 24M609
3300 psi (22.8 MPa, 228 bar) Maximum Working Pressure
311016
309741
309250
309640
ti24865a
Contents
Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Drive Housing and Connecting Rod . . . . . . . . . . . 8
Pinion Assembly/Clutch Armature/Clamp . . . . . . 9
Clutch Housing . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Pressure Control . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Displacement Pump . . . . . . . . . . . . . . . . . . . . . . . 14
2
Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Parts Drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Pressure Control/Filter Assembly . . . . . . . . . . . . 22
Pressure Control/Filter Assembly . . . . . . . . . . . . 23
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 26
311019M
Warning
Warning
The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclamation point
symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When these symbols
appear in the body of this manual or on warning labels, refer back to these Warnings. Product-specific hazard symbols and
warnings not covered in this section may appear throughout the body of this manual where applicable.
WARNING
FIRE AND EXPLOSION HAZARD
Flammable fumes, such as solvent and paint fumes, in work area can ignite or explode. To help prevent fire
and explosion:
•
If using solvent based material, the LineLazer must only be used outside or in buildings very well ventilated with fresh air.
•
The LineLazer must be separately grounded when being cleaned.
•
The LineLazer uses special, conductive tires for static grounding. No substitutions are allowed. Use only
Graco-supplied replacement wheels and tires.
•
Do not fill fuel tank while engine is running or hot; shut off engine and let it cool. Fuel is flammable and can
ignite or explode if spilled on hot surface.
•
When flammable liquid is sprayed or used for flushing or cleaning, keep sprayer at least 20 feet (6 m)
away from explosive vapors.
•
Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and plastic drop
cloths (potential static arc).
•
Keep work area free of debris, including solvent, rags and gasoline.
•
Do not plug or unplug power cords, or turn power or light switches on or off when flammable fumes are
present.
•
Ground equipment and conductive objects in work area. See Grounding instructions.
•
Use only grounded hoses.
•
Hold gun firmly to side of grounded pail when triggering into pail.
•
If there is static sparking or you feel a shock, stop operation immediately. Do not use equipment until
you identify and correct the problem.
SKIN INJECTION HAZARD
High-pressure fluid from gun, hose leaks, or ruptured components will pierce skin. This may look like just a
cut, but it is a serious injury that can result in amputation. Get immediate surgical treatment.
•
Do not point gun at anyone or at any part of the body.
•
Do not put your hand over the spray tip.
•
Do not stop or deflect leaks with your hand, body, glove, or rag.
•
Do not spray without tip guard and trigger guard installed.
•
Engage trigger lock when not spraying.
•
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.
PRESSURIZED EQUIPMENT HAZARD
Fluid from the gun/dispense valve, leaks, or ruptured components can splash in the eyes or on skin and cause
serious injury.
•
Follow Pressure Relief Procedure in this manual, when you stop spraying and before cleaning, checking, or servicing equipment.
•
Tighten all fluid connections before operating the equipment.
•
Check hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.
MOVING PARTS HAZARD
Moving parts can pinch or amputate fingers and other body parts.
•
Keep clear of moving parts.
•
Do not operate equipment with protective guards or covers removed.
•
Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply.
311019M
3
Warning
WARNING
EQUIPMENT MISUSE HAZARD
Misuse can cause death or serious injury.
•
Do not exceed the maximum working pressure or temperature rating of the lowest rated system component. See Technical Data in all equipment manuals.
•
Use fluids and solvents that are compatible with equipment wetted parts. See Technical Data in all equipment manuals. Read fluid and solvent manufacturer’s warnings.
•
Check equipment daily. Repair or replace worn or damaged parts immediately.
•
Do not alter or modify equipment.
•
Use equipment only for its intended purpose. Call your Graco distributor for information.
•
Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.
•
Do not use hoses to pull equipment.
•
Keep children and animals away from work area.
•
Comply with all applicable safety regulations.
PRESSURIZED ALUMINUM PARTS HAZARD
Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon solvents or fluids containing such solvents in pressurized aluminum equipment. Such use can cause serious chemical reaction and
equipment rupture, and result in death, serious injury, and property damage.
SUCTION HAZARD
Never place hands near the pump fluid inlet when pump is operating or pressurized. Powerful suction could
cause serious injury.
CARBON MONOXIDE HAZARD
Exhaust contains poisonous carbon monoxide, which is colorless and odorless. Breathing carbon monoxide
can cause death. Do not operate in an enclosed area.
TOXIC FLUID OR FUMES HAZARD
Toxic fluids or fumes can cause serious injury or death if splashed in the eyes or on skin, inhaled, or swallowed.
•
Read MSDS’s to know the specific hazards of the fluids you are using.
•
Store hazardous fluid in approved containers, and dispose of it according to applicable guidelines.
BURN HAZARD
Equipment surfaces and fluid that’s heated can become very hot during operation. To avoid severe burns, do
not touch hot fluid or equipment. Wait until equipment/fluid has cooled completely.
PERSONAL PROTECTIVE EQUIPMENT
You must wear appropriate protective equipment when operating, servicing, or when in the operating area of
the equipment to help protect you from serious injury, including eye injury, inhalation of toxic fumes, burns,
and hearing loss. This equipment includes but is not limited to:
•
Protective eyewear
•
Clothing and respirator as recommended by the fluid and solvent manufacturer
•
Gloves
•
Hearing protection
RECOIL HAZARD
Brace yourself; gun may recoil when triggered and cause you to fall, which could cause serious injury.
CALIFORNIA PROPOSITION 65
The engine exhaust from this product contains a chemical known to the State of California to cause
cancer, birth defects or other reproductive harm.
This product contains a chemical known to the State of California to cause cancer, birth defects or other
reproductive harm. Wash hands after handling.
4
311019M
Maintenance
Maintenance
Pressure Relief Procedure
Follow the Pressure Relief Procedure whenever
you see this symbol.
DAILY: Check level of TSL in displacement pump packing
nut. Fill nut, if necessary. Keep TSL in nut to help prevent
fluid buildup on piston rod and premature wear of packings
and pump corrosion.AFTER THE FIRST 20 HOURS OF
OPERATION:
Drain engine oil and refill with clean oil. Reference Honda
Engines Owner's Manual for correct oil viscosity.
This equipment stays pressurized until pressure is
manually relieved. To help prevent serious injury from
pressurized fluid, such as skin injection, splashing
fluid and moving parts, follow the Pressure Relief Procedure when you stop spraying and before cleaning,
checking, or servicing the equipment.
1.
Engage trigger lock.
2.
Close the bleed-type master air valve.
3.
Disengage the trigger lock.
4.
Hold a metal part of the gun firmly to a grounded metal
pail. Trigger the gun to relieve pressure.
5.
Engage the trigger lock.
6.
Open all fluid drain valves in the system, having a
waste container ready to catch drainage. Leave drain
valve(s) open until you are ready to spray again.
7.
If you suspect the spray tip or hose is clogged or that
pressure has not been fully relieved:
a.
VERY SLOWLY loosen tip guard retaining nut or
hose end coupling to relieve pressure gradually.
b.
Loosen nut or coupling completely.
c.
Clear hose or tip obstruction.
WEEKLY: Remove engine air filter cover and clean element. Replace element, if necessary. If operating in an
unusually dusty environment: check filter daily and replace,
if necessary.
Replacement elements can be purchased from your local
HONDA dealer.
AFTER EACH 100 HOURS OF OPERATION:
Change engine oil. Reference Honda Engines Owner's
Manual for correct oil viscosity.
SPARK PLUG: Use only BPR6ES (NGK) or W20EPR-U
(NIPPONDENSO) plug. Gap plug to 0.028 to 0.031 in. (0.7
to 0.8 mm). Use spark plug wrench when installing and
removing plug.
Front Wheel Alignment:
Align front wheel as follows:
1.
Fig. Loosen cap screw (90).
NOTICE
For detailed engine maintenance and specifications,
refer to separate Honda Engines Owner's Manual,
supplied.
ti6392a
DAILY: Check engine oil level and fill as necessary.
DAILY: Check hose for wear and damage.
DAILY: Check gun safety for proper operation.
90
FIG. 1
2.
Position front wheel left or right, as necessary, to
straighten alignment.
3.
Tighten cap screw (90). Push striper and let striper roll
with hands off of striper. Note: If striper rolls straight or
veers right or left. Repeat steps 1 and 2 until striper
rolls straight.
DAILY: Check pressure drain valve for proper operation.
DAILY: Check and fill the gas tank.
311019M
5
Troubleshooting
Troubleshooting
Problem
Engine will not start
Engine operates, but displacement
pump does not operate
Cause
Engine switch is OFF
Engine is out of gasoline
Solution
Turn engine switch ON
Refill gas tank. Honda Engines
Owner's Manual.
Engine oil level is low
Check oil level. Replenish oil, if necessary. Honda Engines Owner's Manual.
Spark plug is disconnected or dam- Connect spark plug cable or replace
aged
spark plug
Cold engine
Use choke
Fuel shutoff lever is OFF
Move lever to ON position
Oil is seeping into combustion
Remove spark plug. Pull starter 3 to 4
chamber
times. Clean or replace spark plug.
Start engine. Keep sprayer upright to
avoid oil seepage
Pump switch is OFF
Turn pump switch ON
Pressure setting too low
Turn pressure adjusting knob clockwise to increase pressure.
Fluid filter (104) is dirty
Clean filter. Page 22.
Clean tip or tip filter. Manual 309741.
Tip or tip filter is clogged
Displacement pump piston rod is
Repair pump. Manual 309250.
stuck due to dried paint
Connecting rod is worn or damaged Replace connecting rod. Page 8.
Drive housing is worn or damaged Replace drive housing. Page 8.
Check wiring connections. Page 11, 12.
Electrical power is not energizing
clutch field
Reference pressure control repair. Page 13.
Reference wiring diagram. Page 23.
With pump switch ON and pressure turned to
MAXIMUM, use a test light to check for power
between clutch test points on control board.
Remove clutch wires from control
board and measure resistance across
clutch coil. At 70° F, the resistance
must be between 1.2 +0.2; if not,
replace pinion housing.
Clutch is worn, damaged, or incorrectly positioned
Pinion assembly is worn or damaged
6
Have pressure control checked by authorized
Graco dealer
Adjust or replace clutch. Page 9.
Repair or replace pinion assembly. Page 9.
311019M
Troubleshooting
Problem
Pump output is low
Cause
Solution
Strainer (56) is clogged
Clean strainer.
Piston ball (206) is not seating
Service piston ball. Manual 309250.
Piston packings are worn or damaged
Replace packings. Manual 309250.
O-ring (227) in pump is worn or damaged Replace o-ring. Manual 309250.
Intake valve ball is not seating properly Clean intake valve. Manual 309250.
Intake valve ball is packed with material Clean intake valve. Manual 309250.
Engine speed is too low
Increase throttle setting. Manual 311016.
Clutch is worn or damaged
Adjust or replace clutch. Page 9.
Pressure setting is too low
Increase pressure. Manual 311016.
Fluid filter (104), tip filter or tip is
clogged or dirty
Clean filter. Manual 311016 or 309741.
Large pressure drop in hose with
heavy materials
Use larger diameter hose and/or
reduce overall length of hose. Use of
more than 100 ft of 1/4 in. hose significantly reduces performance of sprayer.
Use 3/8 in. hose for optimum performance (50 ft minimum).
Excessive paint leakage into throat Throat packing nut is loose
packing nut
Fluid is spitting from gun
Pump is difficult to prime
Remove throat packing nut spacer.
Tighten throat packing nut just enough
to stop leakage.
Throat packings are worn or damaged
Replace packings. Manual 309250.
Displacement rod is worn or damaged
Replace rod. Manual 309250.
Air in pump or hose
Check and tighten all fluid connections.
Reprime pump. Manual 311016.
Tip is partially clogged
Clear tip. Manual 309639.
Fluid supply is low or empty
Refill fluid supply. Prime pump. Manual
311016. Check fluid supply often to
prevent running pump dry.
Air in pump or hose
Check and tighten all fluid connections.
Reduce engine speed and cycle pump
as slowly as possible during priming.
Intake valve is leaking
Clean intake valve. Be sure ball seat is
not nicked or worn and that ball seats
well. Reassemble valve.
Pump packings are worn
Replace pump packings. Manual 309250.
Paint is too thick
Thin the paint according to the supplier's recommendations
Engine speed is too high
Decrease throttle setting before priming pump. Manual 311016.
Clutch squeaks each time clutch
engages
Clutch surfaces are not matched to each Clutch surfaces need to wear into each
other when new and may cause noise
other. Noise will dissipate after a day of
run time.
High engine speed at no load
Misadjusted throttle setting
Reset throttle to 3300 engine rpm at no
load
Worn engine governor
Replace or service engine governor
311019M
7
Drive Housing and Connecting Rod
Drive Housing and Connecting Rod
Removal
7.
8.
9.
1.
Relieve pressure, page 5.
2.
FIG. 2. Remove screws (32) and front cover (52).
3.
Remove pump. Refer to Displacement Pump, Removal,
page 14.
4.
Install screws (34) in drive housing. Torque evenly to note
3 value in Fig. 1.
Install pump. Refer to Displacement Pump, Installation,
page 14
Install front cover (52) with two screws (32).
44
49
43
Remove four screws (34) from drive housing (43).
46
34
D
2.
3.
4.
5.
6.
31
141
33
27
Evenly lubricate inside of bronze bearing (C) in drive
housing (43) with high-quality motor oil. Liberally pack top
roller bearing (E), lower bearing (D) inside connecting rod
(29) with bearing grease.
Assemble connecting rod (29) to drive housing (43).
Rotate connecting rod to lowest position.
Apply grease to washers 46, 49 and 48. Install in order
shown in FIG. 3.
Lubricate gears with 0.26 pint of 110293 grease (supplied
with drive housing). Pack grease evenly around gears.
Clean mating surfaces of pinion and drive housings.
Align connecting rod with crank (47) and carefully align
locating pins in drive housing (43) with holes in pinion
housing (44). Push drive housing onto pinion housing or
tap into place with plastic mallet.
136
57
1
Oil
Pack
with bearing grease 110293
2
3 Torque to 130 - 150 in-lb (14 - 16.9 N.m)
FIG. 2
1
46
49
DO NOT use drive housing screws (34) to align or seat
bearing housing with drive housing. Align these parts with
locating pins, to avoid premature bearing wear.
2
48
NOTICE
8
140
118
Inspect crank (47) and connecting rod (29) for excessive
wear and replace parts as needed.
32
E
29
28
Pull connecting rod (29) and lightly tap lower rear of drive
housing (43) with plastic mallet to loosen from pinion
housing (44). Pull drive housing and connecting rod
assembly off pinion housing.
Installation
1.
52
48
Thrust washers may stick to grease inside of drive housing.
Do not lose or misplace.
6.
107
32
47
NOTICE
5.
34
ti24871a
1
47
ti5990a
2
Steel
Copper
FIG. 3
311019M
Pinion Assembly/Clutch Armature/Clamp
Pinion Assembly/Clutch Armature/Clamp
Pinion Assembly/Clutch Armature Removal
42
35
E
Pinion Assembly
If pinion assembly (44) is not removed from clutch housing
(45), do 1. through 3. Otherwise, start at 4.
1.
2.
3.
4.
Relieve pressure, page 5.
Remove drive housing; page 8.
FIG. 11. Disconnect clutch (+) and clutch (–) connectors
from wire harness located under sprayer cart.
FIG. 4. Remove four screws (18) and pinion assembly (44).
ti5531a
ti5987b
FIG. 5
18
7.
8.
44
45
FIG. 6. Remove retaining ring (44d).
Turn pinion assembly over and tap pinion shaft (44c) out
with plastic mallet.
44d
44c
44e
ti5530a
18
ti5532a
FIG. 4
FIG. 6
5.
Clutch Armature
6.
FIG. 5. Place pinion assembly (44) on bench with rotor
side up.
Remove four screws (42) and lock washers (35). Install
two screws in threaded holes (E) in rotor. Alternately
tighten screws until rotor comes off.
9.
FIG. 7. Use an impact wrench or wedge something
between clutch armature (39) and clutch housing to hold
engine shaft during removal.
10. Remove four screws (36) and lock washers (35).
11. Remove armature (39).
39
35
36
ti5533a
FIG. 7
311019M
9
Pinion Assembly/Clutch Armature/Clamp
Installation
Clutch Armature
1.
2.
3.
FIG. 8. Lay two stacks of two dimes on smooth bench
surface.
Lay armature (39) on two stacks of dimes.
Press center of hub down to bench surface.
39
0.12 +.01 in. (3.0 +.25 mm)
ti5534a
dimes
4.
5.
Install armature (39) on engine drive shaft.
Install four screws (36) and lock washers (35) with torque
of 125 in-lb.
Pinion Assembly
6. FIG. 6. Install o-ring (44e).
7. Tap pinion shaft (44c) in with plastic mallet.
8. Install retaining ring (44d) with beveled side facing up.
9. FIG. 5. Place pinion assembly on bench with rotor side up.
10. Apply locktite to screws. Install four screws (42) and lock
washers (35). Alternately torque screws to 125 in-lb until
rotor is secure. Use threaded holes to hold rotor.
11. FIG. 4. Install pinion assembly (44) with four screws (18).
12. Connect clutch (+) and clutch (–) connectors to wire
harness.
FIG. 8
Clamp Removal
1.
Do Engine Removal.
1 Face of clutch housing
2 1.550 ±.010 in. (39.37±.25 mm)
2.
3.
4.
5.
Drain gasoline from tank according to Honda manual.
FIG. 9. Tip engine on side so gas tank is down and air
cleaner is up.
FIG. 10. Loosen two screws (36) on clamp (38),
Push screwdriver into slot in clamp (38) and remove
clamp.
3 Torque to 125 ±.10 in-lb (14 ±1.1 N·m)
4 Chamfer this side
1 45
2
37
ti6199a
37
FIG. 9
B
4
Clamp Installation
1.
2.
3.
10
FIG. 10 Install engine shaft key (37)
Tap clamp (38) onto engine shaft (A). Maintain dimension
shown note 2. Chamfer must face engine.
Check dimension: Place rigid, straight steel bar (B) across
face of clutch housing (45). Use accurate measuring
device to measure distance between bar and face of
clamp. Adjust clamp as necessary. Torque two screws
(36) to 125 ±10 in-lb (14 ±1.1 N·m)
36 3
A
ti5988a
FIG. 10
311019M
Clutch Housing
Clutch Housing
Removal
45
1.
2.
3.
4.
Remove clamp. Do Clamp Removal, page 10.
FIG. 11. Remove four screws (51) and lock washers (50)
which hold clutch housing (45) to engine.
Remove screw (145) from under mounting plate.
Pull off clutch housing (45).
51
50
Installation
1.
2.
3.
FIG. 11. Push on clutch housing (45).
Install four capscrews (51) and lock washers (56) and
secure clutch housing (45) to engine. Torque to 200 in-lb
(22.6 N·m).
Install screw (145) from beneath mounting plate. Torque
to 26 ft-lb (35.2 N·m).
145
ti6322a
FIG. 11
Engine
Removal
NOTE: All service to the engine must be performed by
an authorized HONDA dealer.
1.
2.
3.
4.
Remove Pinion Assembly/Clutch Armature/Clamp and
Clutch Housing, as instructed on pages 9, 10 and 11.
FIG. 12. Disconnect all necessary wiring.
FIG. 13. Remove two locknuts (111) and screws (110)
from base of engine.
Lift engine carefully and place on work bench.
110
clutch wires
ti6323a
pink
(from engine)
111
FIG. 13
ground
green/yellow
Installation
1.
2.
ti6390a
FIG. 12
311019M
3.
4.
5.
Lift engine carefully and place on cart.
FIG. 13. Install two screws (110) in base of engine and
secure with locknuts (111). Torque to 20 ft-lb (27.12 N·m).
FIG. 12. Connect all necessary wiring.
Install Pinion Assembly/Clutch Armature/Clamp and
Clutch Housing, as instructed on pages 9 and 10 and 11.
Set engine to 3300 rpm.
11
Pressure Control
Pressure Control
On/Off Switch
Installation
Removal
1.
2.
3.
1.
2.
3.
4.
Install new ON/OFF switch (62d) so tabs of switch snap
into place on inside of cover.
Connect ON/OFF switch connector (B) to PC board.
Close cover (62a) and secure with two screws (108).
Relieve pressure, page 5.
FIG. 14. Remove two screws (108) and open cover (62a).
Disconnect ON/OFF switch connector from PC board.
Press in on two retaining tabs on each side of ON/OFF
switch (62d) and remove switch from cover.
62d
62c
62b
62a
62e
pink
(from engine)
ground
green/yellow
clutch (-)
(black)
clutch (+)
(red)
62g
62f
155
62b
66
108
ti6389a
FIG. 14
12
311019M
Pressure Control
Control Board
Removal
5.
•
Clutch wires
Remove four screws (62f) and control board (62e).
Installation
1.
2.
3.
4.
Relieve pressure, page 5.
FIG. 14. Remove two screws (108) and open cover (62a)
Disconnect engine and ground wires from wire harness (66).
Disconnect at control board (62e):
•
Lead from potentiometer (62b)
•
Lead from transducer (155)
•
Lead from ON/OFF switch (62d)
1.
2.
3.
4.
FIG. 14. Install control board (62e) with four screws (62f).
Connect at control board (62e):
•
Clutch wires
•
Lead from ON/OFF switch (62d)
•
Lead from transducer (155)
•
Lead from potentiometer (62b)
Connect engine and ground wires.
Close cover (62a) and secure with two screws (108).
Pressure Control Transducer
Removal
Installation
1.
2.
1.
2.
3.
4.
5.
Relieve pressure, page 5.
FIG. 14. Remove two screws (108) and open cover (62a)
Disconnect transducer (155) lead from control
board (62e).
Pull transducer connector through strain relief
bushing (151).
Remove transducer and o-ring (99) from filter housing (67).
3.
4.
FIG. 14. Install o-ring (99) and transducer (155) in filter
housing (67). Torque to 35 - 45 ft-lb.
Install transducer connector and strain relief bushing in
control housing.
Connect lead (E) to control board (62e).
Close cover (62a) and secure with two screws (108).
Pressure Adjust Potentiometer
Removal
Installation
1.
2.
1.
2.
3.
4.
5.
Relieve pressure, page 5.
Fig. 13.Remove two screws (108) and open cover (62a).
Disconnect potentiometer (62b) lead from control board
(62e).
Loosen set screws on potentiometer knob (62c) and
remove knob, shaft nut, lock washer and potentiometer
(62b).
Remove spacer (62g) from potentiometer.
311019M
3.
4.
Install spacer (62g) on potentiometer (62b).
FIG. 14. Install potentiometer, shaft nut, lock washer and
potentiometer knob (62c).
a.Turn potentiometer shaft clockwise to internal stop.
Assemble potentiometer knob (62c) to strike pin on
cover (62a).
b.After adjustment of step a., tighten both set screws in
knob 1/4 to 3/8 turn after contact with shaft.
Connect potentiometer (62b) lead to control board (62e).
Close cover (62a) and secure with two screws (108).
13
Displacement Pump
Displacement Pump
Removal
6.
1.
Flush pump.
2.
3.
Relieve pressure, page 5.
FIG. 16. Stop pump with piston rod (201) in its lowest
position.
FIG. 15. Loosen two screws (32) and remove pump rod
cover (107).
4.
FIG. 17. Loosen jam nut by hitting firmly with a hammer.
Unscrew pump.
ti5545a
32
FIG. 17
107
Repair
ti6468a
See manual 309250 for pump repair instructions.
FIG. 15
5.
FIG. 16. Remove hose (118) and suction hose (57). Use
screwdriver; push retaining spring up; push out pin (31).
31
ti6467a
201
118
57
FIG. 16
14
311019M
Displacement Pump
Installation
NOTICE
If pin works loose, parts could break off due to force of
pumping action. Parts could project through the air
and result in serious injury or property damage. Make
sure pin and retaining spring are properly installed.
NOTICE
ti6111a
If the pump jam nut loosens during operation, the
threads of the bearing housing and drive train will be
damaged. Tighten jam nut as specified.
ti6110a
1.
Fig. FIG. 18. Pull piston rod out distance shown. Screw in
pump until holes in connecting rod and piston rod align.
ti5544a
FIG. 19
ti5546a
4.
FIG. 20. Fill packing nut with Graco TSL until fluid flows
onto the top of seal. Install pump rod cover (107).
ti5543a
1
ti5546b
FIG. 18
2.
3.
FIG. 12. Push pin (31) into hole. Push retaining ring spring
into groove all the way around connecting rod.
FIG. 19. Screw jam nut down onto pump until nut stops.
Screw pump up into drive housing until top threads of
pump are flush with drive housing face (FIG. 20). Back off
pump and jam nut to align pump outlet to side. Tighten jam
nut by hand, then tap 1/8 to 1/4 turn with a 20 oz
(maximum) hammer to approximately 75 ±5 ft-lb (102
N·m). Connect hose (118) suction hose (57).
311019M
1
Drive housing face
FIG. 20
15
Parts Drawing
Parts Drawing
130
74
55
94
108
19
149
143
53
151
59
184
147
148 ref
18
54
66
129
148
9
132
97
85
84
83
144
81
1
82
15
115
60
114
16
110
89
93
9
64
137
111
9
86
150
3
5
64
93
131
11
8
14
7
10
153
158
115
ti24872a
93
64
74
91
112
90
4
6
65
2
65
ti6242c
16
311019M
Parts List
Parts List
Ref.
No.
1
2
3
4
5
6
7
8
9
10
11
14
15
16
18
19
53
54
55
59
60
64
65
66
74
81
82
83
84
85
86
Part No.
287630
119542
119543
15F127
119532
15E780
15E773
15E792
101566
114682
108471
287682
108879
206994
249080
24U241
194310
115077
116139
15E992
15E993
119563
15E996
15E995
241445
195134
198891
198931
113961
114808
119569
311019M
Description
FRAME, LL
WHEEL, small
WHEEL, large
FORK, painted
BEARING, flanged
PIN, fork
DISK, adjuster
PIN, lever
NUT, lock
SPRING, compression
KNOB, pronged
LEVER, caster, includes 26
ENGINE, gasoline, 4.0 hp
FLUID, TSL, 8 oz
HOSE, coupled, 1/4 in. x 50 ft, nickel
KIT, pail cover
LEVER, actuator
PAIL, plastic
GRIP, handle
CABLE, gun
ROD, brake
WASHER, belleville
SPACER, wheel
HARNESS, wiring, control
CABLE, caster
SPACER, ball, guide
BRACKET, mounting
BEARING
SCREW, cap, hex hd
CAP, vinyl
BUSHING, strain relief
Qty
.
1
1
2
1
2
1
1
1
7
1
1
1
1
1
2
1
2
1
1
4
2
1
1
1
1
1
1
1
1
Ref.
No.
89
90
91
93
94
97
108
110
111
112
114
115
129
130
131
132
137
143
144
147
148
149
150
151
153
158
184
Part No.
15E955
100057
113665
119554
248912
116935
116719
110837
110838
118866
110963
111040
101550
278723
15C871
100731
119579
15F549
16N451
194126
112798
237686
15F638
15F637
15F928
111025
114802
119771
Description
HOLDER, bucket
SCREW, cap, hex hd
SCREW, cap, hex hd
NUT, lock, nylon, thin pattern
BAR, handle, LL
SCREW, cap, flnghd
SCREW, 8-32 hex washer head
SCREW, flange, hex
NUT, lock
WASHER, flat, extra thick
SCREW, cap, flng hd
NUT, lock, insert, nylock, 5/16 in.
SCREW, cap, sch
GASKET, pail
CAP, leg
WASHER
CONDUCTOR, ground
LABEL, identification
LABEL, BRAND, HANDLE
(Model 24M609)
LABEL, warning
SCREW, thread forming, hex hd
WIRE, ground assembly w/ clamp
LABEL, GMAX warning fire & skin
LABEL, GMAX warning skin inject
BUSHING, strain relief
GASKET, polypropylene (Wagner)
STOP, wire
STRAP, cover (Model 249007)
Qty
.
2
1
1
4
1
2
2
2
2
1
2
3
2
1
2
2
1
1
1
1
1
1
1
1
1
1
1
1
 Replacement Danger and Warning labels, tags, and
cards are available at no cost.
17
Parts Drawing
Parts Drawing
140
139
35
75
57
68
44
130
47
52
35
39
37
ti24873a
46
48
56
32
49
41
36
40
36
34
42
107
35
38
51
50
145
45
35
32
146
34
29
142
28
31
27
33
30
141
118
57
136
18
311019M
Parts Drawing
Parts List
Ref
No.
27
28
29
30
31
32
33†
34
35*
36*
37
38
39*
40*
41*
42*
43
44
45
46
47
48
49
Part No.
246428
196750
287053
195150
196762
117501
115099
119426
105510
108803
183401
193680
101682
287483
287376
15E535
116074
287484
180131
107434
311019M
Description
Qty
PUMP, displacement, st
1
SPRING, retaining
1
ROD, connecting
1
NUT, jam, pump
1
PIN, straight
1
SCREW, mach, hex washer head
4
WASHER
1
SCREW, mach, hex washer hd
8
WASHER, lock, spring (hi-collar)
10
SCREW, hex, socket head
6
KEY, parallel
1
COLLAR, shaft
1
ARMATURE, clutch, 4 in.
1
HUB, armature
1
ROTOR, clutch, 4 in.
1
SCREW, cap, sch
4
HOUSING, drive, includes 32, 34
1
HOUSING, pinion
1
HOUSING, clutch, machine
1
WASHER, thrust
1
CRANK, GMAX 3000, includes 46,
1
48, 49
BEARING, thrust
1
BEARING, thrust
1
Ref
No.
50
51
52
56
57
68
75
107
118
136†
139
140
141
142
145
146
Part No.
100214
108842
287487
246385
287683
114958
249232
15B589
249149
117559
196180
16X071
196181
15F538
16N450
112395
290228
Description
Qty
WASHER, lock
4
SCREW, cap, hex hd
4
COVER, front, painted, includes 32
1
STRAINER, 7/8-14 unf
1
HOSE, suction, includes 33, 56,
1
130, 136
STRAP, tie
5
HOSE, cpld, 1/4 in. X 3 ft
1
COVER, pump rod
1
HOSE, coupled, 1/4 X 22.25 in.
1
O-RING
2
BUSHING
1
TUBE, drain
1
FITTING, nipple
2
LABEL, identification
1
LABEL, PUMP (Model 24M609)
1
SCREW, cap, flnghd
1
LABEL, caution
1
 Replacement Danger and Warning labels, tags, and
cards are available at no cost
* Included in Clutch Replacement Kit 241109
† Included in Suction Hose Kit 249356
19
Parts Drawing
Parts Drawing and List - Pinion Housing
Ref No. 44: Pinion Housing
No.
44
44a
44b
44c*
44d*
Part No.
287376
287482
105489
287485
113094
Description
PINION HOUSING
KIT, repair, coil
PIN
PINION SHAFT
RETAINING RING, large
Qty
1
1
2
1
1
* May be ordered separately
44
44d
44c
44e
44b
44a
ti5539a
20
311019M
Parts Drawing
Gun Arm Parts
77
23
24
72
73
20f
20e
20a
25
20f
20
18 Ref
20g
20f
17
156
20d
21
Ref
17
20
20a
20b
20c
20d
20e
20f
20g
Part
248157
287570
287569
15F214
15F209
24Y991
15F211
102040
24Y991
311019M
Description
GUN, Flex, basic
HOLDER, gun
HOLDER, gun
LEVER, actuator
STUD, pull trigger
KIT, pivot
STUD, cable
NUT, lock
KIT, pivot
ti6241b
Qty
1
1
1
1
1
1
1
4
1
Ref
21
23
24
25
59
70
72
73
77
156
Part
243161
287566
15F212
15F213
15E992
119648
224052
119647
188135
LL5319
20b
20c
Description
Qty
GUARD, RAC 5
1
KIT, clamp
1
ARM, holder, gun
1
BRACKET, cable
1
CABLE, gun
1
SCREW, mach, trusshd, cross recess 1
BRACKET, support gun
1
SCREW, cap, socket, flthd
2
GUIDE, cable
1
TIP, spray, striping
1
21
Pressure Control/Filter Assembly
Pressure Control/Filter Assembly
62d
62c
62h
62b
62a
63
62e
pink
(from engine)
105
ground
(green/yellow)
104
clutch (-)
(black)
62f
clutch (+)
(red)
155
103
62g
62b
87
13
87
155 Ref
18 Ref
106
101
99
152
102
67
98
141
106
118 Ref
ti6239b
100 75 Ref
183
ti6389a
182
106 Ref
181
22
311019M
Pressure Control/Filter Assembly
Pressure Control/Filter Assembly
Ref
13
62
62a
62b
62c
62d
62e
62f
62g
62h
63*
67*
87
98*
99*
Part
Description
Qty
15E748 BRACKET, manifold
1
CONTROL, assy
15E991 COVER, control box
1
256219 POTENTIOMETER
1
116167 KNOB, potentiometer
1
116752 SWITCH, rocker
1
287486 BOARD, control,
1
113045 SCREW, sems, mach, phillips, truss 4
198650 SPACER, shaft
1
15F540 LABEL, instructions
1
287285 CAP, manifold, includes 103, 105
1
15H561 MANIFOLD, filter
1
111801 SCREW, cap, hex hd
4
15C780 HANDLE
1
111457 O-RING
1
Ref
100*
101*
102*
103*
104*
105*
106
141
152*
155*
181
182
183
Part
15C972
224807
239914
117285
244067
15C766
196177
196181
101748
15F782
196178
102814
241339
Description
Qty
PIN, grooved
1
BASE, valve
1
VALVE, drain
1
O-RING
1
FILTER, fluid
1
TUBE, diffusion
1
ADAPTER, nipple
2
FITTING, nipple
1
PIPE, plug, sst
1
HARNESS, transducer, line striper
1
NIPPLE, 3/8 x 3/8 in.
1
GAUGE, pressure fluid
1
KIT, gauge, 3/8 in., includes 181, 182 1
* Included in Filter Repair Kit 287685
DRIVE
HOUSING
PINON
HOUSING
Pressure Control
Wiring Diagram
TO ENGINE
CLUTCH B
CLUTCH A
TO GROUND
CONTROL BOARD
ti5542b
ON/OFF SWITCH
TRANSDUCER
POTENTIOMETER
311019M
23
Technical Data
Technical Data
Honda GX120 Engine
ANSI Power Rating @ 3600 rpm
4.0 Horsepower
(2.9 kW)
3300 psi
(227 bar, 22.7 MPa)
Maximum working pressure
Noise Level
Sound power
100 dBa
per ISO 3744
86 dBa
measured at 3.1 feet (1 m)
Sound pressure
Vibration Level
* Left hand
3.89 m/sec2
* Right hand
4.94 m/sec2
*Vibration measured per ISO 5349
Based on 8 hr daily exposure
0.75 gpm (2.84 liter/min)
1 gun with 0. 027 in. tip
12 mesh (893 micron)
stainless steel screen, reusable
60 mesh (250 micron)
stainless steel screen, reusable
1¼-12 unf-2b
¼ npsm from fluid filter
PTFE, Nylon, polyurethane, UHMW polyethylene, FKM,
acetal, leather, tungsten carbide, nickel-plated carbon
steel, stainless steel, chrome plating
Maximum delivery rating
Maximum tip size
Inlet paint strainer
Outlet paint filter
Pump inlet size
Fluid outlet size
Wetted parts
Dimensions
Sprayer
248861
249007
24M609
24
Weight lb (kg)
150 (68)
150 (68)
150 (68)
Height in. (cm)
40.5 (103)
40.5 (103)
40.5 (103)
Width in. (cm)
32 (81)
32 (81)
32 (81)
Length in. (cm)
61.5 (156)
61.5 (156)
61.5 (156)
311019M
Notes
Notes
311019M
25
Graco Standard Warranty
Graco warrants all equipment referenced in this document which is manufactured by Graco and bearing its name to be free from defects in
material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty
published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by
Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written
recommendations.
This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty
installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of
non-Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with
structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance
of structures, accessories, equipment or materials not supplied by Graco.
This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of
the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned
to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will
be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation.
Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy
(including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or
consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale.
GRACO MAKES NO WARRANTY, AND DISCLAIMS ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, IN CONNECTION WITH ACCESSORIES, EQUIPMENT, MATERIALS OR COMPONENTS SOLD BUT NOT
MANUFACTURED BY GRACO. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to
the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these
warranties.
In no event will Graco be liable for indirect, incidental, special or consequential damages resulting from Graco supplying equipment hereunder, or
the furnishing, performance, or use of any products or other goods sold hereto, whether due to a breach of contract, breach of warranty, the
negligence of Graco, or otherwise.
FOR GRACO CANADA CUSTOMERS
The Parties acknowledge that they have required that the present document, as well as all documents, notices and legal proceedings entered into,
given or instituted pursuant hereto or relating directly or indirectly hereto, be drawn up in English. Les parties reconnaissent avoir convenu que la
rédaction du présente document sera en Anglais, ainsi que tous documents, avis et procédures judiciaires exécutés, donnés ou intentés, à la suite
de ou en rapport, directement ou indirectement, avec les procédures concernées.
ADDITIONAL WARRANTY COVERAGE
Graco does provide extended warranty and wear warranty for products described in the Graco Contractor Equipment Warranty Program.
Graco Information
For the latest information about Graco products, visit www.graco.com.
For patent information, see www.graco.com/patents.
TO PLACE AN ORDER, contact your Graco distributor or call 1-800-690-2894 to identify the nearest distributor.
All written and visual data contained in this document reflects the latest product information available at the time of publication.
Graco reserves the right to make changes at any time without notice.
For patent information, see www.graco.com/patents
Original instructions. This manual contains English. MM 311019
Graco Headquarters: Minneapolis
International Offices: Belgium, China, Japan, Korea
GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA
Copyright 2005, Graco Inc. All Graco manufacturing locations are registered to ISO 9001.
www.graco.com
Revised M, October 2015