HPE FlexNetwork 5510 HI Switch Series

QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Overview
HPE FlexNetwork 5510 HI Switch Series
Models
HPE FlexNetwork 5510 24G 4SFP+ HI 1-slot Switch
HPE FlexNetwork 5510 48G 4SFP+ HI 1-slot Switch
HPE FlexNetwork 5510 24G PoE+ 4SFP+ HI 1-slot Switch
HPE FlexNetwork 5510 48G PoE+ 4SFP+ HI 1-slot Switch
HPE FlexNetwork 5510 24G SFP 4SFP+ HI 1-slot Switch
JH145A
JH146A
JH147A
JH148A
JH149A
Key features
•
•
•
•
•
Scalable with 10 Gigabit uplinks and 9-chassis IRF with up to 160 GB/s stacking bandwidth
40G QSFP+ ports for uplink or stacking
4 convenient built-in SFP+ 10GbE uplinks provide performance for bandwidth hungry applications
PoE+ for up to 30 Watts of PoE power per port on all ports simultaneously
MACsec support
Product overview
The HPE FlexNetwork 5510 HI Switch Series comprises Gigabit Ethernet switches that deliver outstanding resiliency, security, and
multiservice support capabilities at the edge layer of data center, large campus, and metro Ethernet networks. The switches can also
be used in the core layer of SMB networks.
With Intelligent Resilient Fabric (IRF) support and available dual power supplies, the HPE FlexNetwork 5510 HI Series Switch can
deliver the highest levels of resiliency and manageability. In addition, the PoE+ models provide up to 1440 W of PoE+ power with
the dual power supply configuration.
Designed with four fixed 10GbE ports and supports additional modular uplinks, these switches can provide up to six 10GbE uplink
ports. With complete IPv4/IPv6, OpenFlow, and MPLS/VPLS features, the series provides investment protection with an easy
transition from IPv4 to IPv6 networks.
Features and benefits
Software-defined networking
Page 1
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Overview
•
OpenFlow
supports OpenFlow 1.3 specification to enable SDN by allowing separation of the data (packet forwarding) and control
(routing decision) paths
Quality of Service (QoS)
•
•
•
•
•
Advanced classifier-based QoS
classifies traffic using multiple match criteria based on Layer 2, 3, and 4 information; applies QoS policies such as setting
priority level and rate limit to selected traffic on a per-port or per-VLAN basis
Traffic policing
supports Committed Access Rate (CAR) and line rate
Powerful QoS feature
creates traffic classes based on access control lists (ACLs), IEEE 802.1p precedence, IP, and DSCP or Type of Service
(ToS) precedence; supports filter, redirect, mirror, or remark; supports the following congestion actions: strict priority (SP)
queuing, weighted round robin (WRR), weighted fair queuing (WFQ), weighted random early discard (WRED), weighted
deficit round robin (WDRR), SP+WDRR, and SP+WFQ
Storm restraint
allows limitation of broadcast, multicast, and unknown unicast traffic rate to reduce unwanted broadcast traffic on the
network
Broadcast control
allows limitations of broadcast traffic rate to cut down on unwanted network broadcast traffic
Management
•
•
•
•
•
•
•
•
•
•
•
•
Friendly port names
allows assignment of descriptive names to ports
sFlow (RFC 3176)
provides scalable ASIC-based wirespeed network monitoring and accounting with no impact on network performance; this
allows network operators to gather a variety of sophisticated network statistics and information for capacity planning and
real-time network monitoring purposes
Complete session logging
provides detailed information for problem identification and resolution
Remote configuration and management
enables configuration and management through a CLI located on a remote device
Manager and operator privilege levels
provides read-only (operator) and read/write (manager) access on CLI management interfaces
Management VLAN
segments traffic to and from management interfaces, including CLI/Telnet and SNMP
Command authorization
leverages RADIUS/HWTACACS to link a custom list of CLI commands to an individual network administrator's login; also
provides an audit trail
Remote monitoring (RMON)
uses standard SNMP to monitor essential network functions; supports events, alarm, history, and statistics group plus a
private alarm extension group
Multiple configuration files
stores easily to the flash image
Remote intelligent mirroring
mirrors ingress/egress ACL-selected traffic from a switch port or VLAN to a local or remote switch port anywhere on the
network
In-service software upgrade (ISSU)
enables operators to perform upgrades in the shortest possible amount of time with reduced risk to network operations or
traffic disruptions
Network Management
SNMP v1/v2c/v3, MIB-II with Traps, and RADIUS Authentication Client MIB (RFC 2618); embedded HTML management
tool with secure access
Page 2
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Overview
•
•
•
IPv6 management
provides future-proof networking because the switch is capable of being managed whether the attached network is
running IPv4 or IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6, syslogv6, FTPv6, SNMPv6, DHCPv6, and
RADIUS for IPv6
Troubleshooting
ingress and egress port monitoring enables network problem-solving; virtual cable tests provide visibility into cable
problems
HPE Intelligent Management Center (IMC)
integrates fault management, element configuration, and network monitoring from a central vantage point; built-in
support for third-party devices enables network administrators to centrally manage all network elements with a variety of
automated tasks, including discovery, categorization, baseline configurations, and software images; the software also
provides configuration comparison tools, version tracking, change alerts, and more
Connectivity
•
•
•
•
•
•
•
•
Auto-MDIX
automatically adjusts for straight-through or crossover cables on all 10/100/1000 ports
Packet storm protection
protects against broadcast, multicast, or unicast storms with user-defined thresholds
Ethernet operations, administration and maintenance (OAM)
detects data link layer problems that occurred in the "last mile" using the IEEE 802.3ah OAM standard; monitors the status
of the link between two devices
Flow control
provides back pressure using standard IEEE 802.3x, reducing congestion in heavy traffic situations
Fixed 10GbE ports
provides four fixed SFP+ ports for a 20 GbE connection to the network without the need for additional extension interface
modules
Optional 10GbE or 40GbE ports
deliver, through the use of optional modules, additional 10GbE or 40GbE connections, which are available for uplinks or
high-bandwidth server connections; flexibly support copper, SFP+, or 40GbE QSFP+ connections
Jumbo packet support
supports up to 10000-byte frame size to improve the performance of large data transfers
IEEE 802.3at Power over Ethernet (PoE+)
provides up to 30 W per port that allows support of the latest PoE+-capable devices such as IP phones, wireless access
points, and security cameras, as well as any IEEE 802.3af-compliant end device; eliminates the cost of additional electrical
cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments
Performance
•
•
Hardware-based wirespeed access control lists (ACLs)
help provide high levels of security and ease of administration without impacting network performance with a feature-rich
TCAM-based ACL implementation
Nonblocking architecture
delivers up to 336 Gb/s of wire-speed switching with a nonblocking switching fabric and up to 250 million pps throughput
Resiliency and high availability
•
•
•
Separate data and control paths
separates control from services and keeps service processing isolated; increases security and performance
Device Link Detection Protocol (DLDP)
monitors link connectivity and shuts down ports at both ends if unidirectional traffic is detected, preventing loops in STPbased networks
Intelligent Resilient Fabric (IRF)
creates virtual resilient switching fabrics, where two to nine switches perform as a single L2 switch and L3 router; switches
Page 3
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Overview
•
•
•
•
•
•
do not have to be co-located and can be part of a disaster-recovery system; servers or switches can be attached using
standard LACP for automatic load balancing and high availability; can eliminate need for complex protocols like Spanning
Tree Protocol, Equal-Cost Multipath (ECMP), or VRRP, thereby simplifying network operation
Rapid Ring Protection Protocol (RRPP)
connects multiple switches in a high-performance ring using standard Ethernet technology; traffic can be rerouted around
the ring in less than 50 ms, reducing the impact on traffic and applications
Smart Link
Allows under 100ms failover between links
Virtual Router Redundancy Protocol (VRRP)
allows groups of two routers to dynamically back each other up to create highly available routed environments
IRF Capability
provides single IP address management for a resilient virtual switching fabric of up to nine switches using up to 160 Gb/s
bidirectional using QSFP+ links
Spanning Tree/PVST+, MSTP, RSTP
provides redundant links while preventing network loops
Internal Dual Redundant Power Supply
provides high reliability by keeping network up while delivering up to 1440 Watts of PoE+
Manageability
•
•
•
•
Dual flash images
provides independent primary and secondary operating system files for backup while upgrading
Multiple configuration files
allow multiple configuration files to be stored to a flash image
Troubleshooting
allows ingress and egress port monitoring, enabling network problem solving; virtual cable tests provide visibility into cable
problems
IPv6 management
future-proofs networking, as the switch is capable of being managed whether the attached network is running IPv4 or
IPv6; supports pingv6, tracertv6, Telnetv6, TFTPv6, DNSv6, and ARPv6
Layer 2 switching
•
•
•
•
•
•
•
•
•
GARP VLAN Registration Protocol
allows automatic learning and dynamic assignment of VLANs
IP multicast snooping and data-driven IGMP
automatically prevents flooding of IP multicast traffic
Internet Group Management Protocol (IGMP) and Multicast Listener Discovery (MLD) protocol snooping
controls and manages the flooding of multicast packets in a Layer 2 network
32K MAC addresses
provide access to many Layer 2 devices
IEEE 802.1ad QinQ and selective QinQ
increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple LANs on a highspeed campus or metro network
10GbE port aggregation
allows grouping of ports to increase overall data throughput to a remote device
Spanning Tree/MSTP, RSTP, and STP root guard
prevent network loops
64 MSTP instances
allow multiple configurations of STP per VLAN group
Isolation at data link layer with private VLANs
provides, through a two-tier VLAN structure, an additional layer of protection, simplifying network configuration while
saving VLAN resources
Page 4
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Overview
•
VLAN support and tagging
supports the IEEE 802.1Q (4094 VLAN IDs)
Layer 3 services
•
•
•
•
•
•
Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous ARP allows detection
of duplicate IP addresses; proxy ARP allows normal ARP operation between subnets or when subnets are separated by a
Layer 2 network
Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks; supports client; DHCP Relay enables DHCP operation across subnets
Loopback interface address
defines an address that can always be reachable, improving diagnostic capability
User Datagram Protocol (UDP) helper function
allows UDP broadcasts to be directed across router interfaces to specific IP unicast or subnet broadcast addresses and
prevents server spoofing for UDP services such as DHCP
Route maps
provide more control during route redistribution; allow filtering and altering of route metrics
DHCP server
centralizes and reduces the cost of the IPv4 address management
Layer 3 routing
•
•
•
•
•
•
•
•
•
IPv4 routing protocols
support static routes, RIP, OSPF, ISIS, and BGP
IPv6 routing protocols
provide routing of IPv6 at wire speed; support static routes, RIPng, OSPFv3, IS-ISv6, and BGP4+ for IPv6
PIM-SSM, PIM-DM, and PIM-SM (for IPv4 and IPv6)
support IP Multicast address management and inhibition of DoS attacks
MPLS support
provides extended support of MPLS, including MPLS VPNs and MPLS Traffic Engineering (MPLS TE)
Virtual Private LAN Service (VPLS)
establishes point-to-multipoint Layer 2 VPNs across a provider network
Bidirectional Forwarding Detection (BFD)
enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, IS-IS, VRRP, MPLS, and
IRF
Policy-based routing
makes routing decisions based on policies set by the network administrator
Equal-Cost Multipath (ECMP)
enables multiple equal-cost links in a routing environment to increase link redundancy and scale bandwidth
IPv6 tunneling
allows a smooth transition from IPv4 to IPv6 by encapsulating IPv6 traffic over an existing IPv4 infrastructure
Security
•
•
•
•
Access control lists (ACLs)
provide IP Layer 2 to Layer 4 traffic filtering; support global ACL, VLAN ACL, port ACL, and IPv6 ACL; up to 3K ingress
ACLs and 1K egress ACLs are supported
IEEE 802.1X
defines an industry-standard method of user authentication using an IEEE 802.1X supplicant on the client in conjunction
with a RADIUS server
MAC-based authentication
client is authenticated with the RADIUS server based on the client's MAC address
Identity-driven security and access control
Page 5
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Overview
−
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Per-user ACLs
permits or denies user access to specific network resources based on user identity and time of day, allowing
multiple types of users on the same network to access specific network services without risking network security
or providing unauthorized access to sensitive data
− Automatic VLAN assignment
automatically assigns users to the appropriate VLAN based on their identities
Port security
allows access only to specified MAC addresses, which can be learned or specified by the administrator
Secure FTP/ SCP
allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a
switch configuration file
STP BPDU port protection
blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks
DHCP protection
blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks
DHCP snooping
helps ensure that DHCP clients receive IP addresses from authorized DHCP servers and maintain a list of DHCP entries
for trusted ports; prevents reception of fake IP addresses and reduces ARP attacks, improving security
DHCPv6 snooping
ensures that DHCPv6 clients obtain IPv6 addresses from authorized DHCPv6 servers and record IP-to-MAC mappings of
DHCPv6 clients
Dynamic ARP protection
blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data
STP root guard
protects the root bridge from malicious attacks or configuration mistakes
Guest VLAN
provides a browser-based environment to authenticated clients that is similar to IEEE 802.1X
Port isolation
secures and adds privacy, and prevents malicious attackers from obtaining user information
Endpoint Admission Defense (EAD)
provides security policies to users accessing a network
RADIUS/HWTACACS
eases switch management security administration by using a password authentication server
Secure management access
delivers secure encryption of all access methods (CLI, GUI, or MIB) through SSHv2, SSL, HTTPS and/or SNMPv3
Unicast Reverse Path Forwarding (URPF)
allows normal packets to be forwarded correctly, but discards the attaching packet due to lack of reverse path route or
incorrect inbound interface; prevents source spoofing and distributed attacks; supports distributed URPF
IP source guard
helps prevent IP spoofing attacks
IPv6 source guard
help prevent IPv6 spoofing attacks using ND Snooping as well as DHCPv6 Snooping
ND Snooping
allows only packets with a legally obtained IPv6 address to pass
Virtual private network (VPN)
•
Generic Routing Encapsulation (GRE)
transports Layer 2 connectivity over a Layer 3 path in a secured way; enables the segregation of traffic from site to site
Convergence
Page 6
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Overview
•
•
•
•
•
•
•
•
•
•
LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to automatically configure
network devices such as IP phones
Internet Group Management Protocol (IGMP)
utilizes Any-Source Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast networks; supports
IGMPv1, v2, and v3
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
facilitates easy mapping using network management applications with LLDP automated device discovery protocol
Multicast Source Discovery Protocol (MSDP)
allows multiple PIM-SM domains to interoperate; is used for inter-domain multicast applications
Multicast VLAN
allows multiple VLANs to receive the same IPv4 or IPv6 multicast traffic, lessening network bandwidth demand by
reducing or eliminating multiple streams to each VLAN
LLDP-CDP compatibility
receives and recognizes CDP packets from Cisco's IP phones for seamless interoperation
IEEE 802.3at Power over Ethernet (PoE+)
provides up to 30 W per port that allows support of the latest PoE+-capable devices such as IP phones, wireless access
points, and security cameras, as well as any IEEE 802.3af-compliant end device; eliminates the cost of additional electrical
cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments
PoE allocations
supports multiple methods (automatic, IEEE 802.3af class, LLDP-MED, or user-specified) to allocate PoE power for more
efficient energy savings
Voice VLAN
automatically assigns VLAN and priority for IP phones, simplifying network configuration and maintenance
IP multicast snooping (data-driven IGMP)
prevents flooding of IP multicast traffic
Additional information
•
•
•
•
Green initiative support
provides support for RoHS and WEEE regulations
Green IT and power
improves energy efficiency through the use of the latest advances in silicon development; shuts off unused ports and
utilizes variable-speed fans, reducing energy costs
Unified Hewlett Packard Enterprise Comware operating system with modular architecture
provides an easy-to-enhance-and-extend feature set, which doesn't require whole-scale changes; all switching, routing,
and security platforms leverage the Comware OS, a common unified modular operating system
Energy Efficient Ethernet (EEE) support
Reduces power consumption in accordance with IEEE 802.3az
Warranty and support
•
•
Limited Lifetime Warranty
See http://www.hpe.com/networking/warrantysummary for warranty and support information included with your
product purchase.
Software releases
to find software for your product, refer to http://www.hpe.com/networking/support; for details on the software releases
available with your product purchase, refer to http://www.hpe.com/networking/warrantysummary
Page 7
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Configuration
Build To Order: BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or RackShippable solution.
Switch Chassis
HPE FlexNetwork 5510 24G 4SFP+ HI 1-slot Switch
• 24 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH145A
See Configuration
NOTE: 2
HPE FlexNetwork 5510 48G 4SFP+ HI 1-slot Switch
• 48 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH146A
See Configuration
NOTE: 2
HPE FlexNetwork 5510 24G PoE+ 4SFP+ HI 1-slot Switch
• 24 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH147A
See Configuration
NOTE: 2
HPE FlexNetwork 5510 48G PoE+ 4SFP+ HI 1-slot Switch
• 48 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH148A
See Configuration
NOTE: 2
HPE FlexNetwork 5510 24G SFP 4SFP+ HI 1-slot Switch
• 16 SFP fixed Gigabit Ethernet SFP ports (min=0 \ max=16 SFP Transceivers)
• 8 RJ-45/ SFP fixed combo ports (min=0 \ max=8 SFP Transceivers)
• 4 fixed SFP+ ports (min=0 \ max=4 SFP+ Transceivers)
• 1 open module slots, or a combination
• Must select min 1 power supply
• 1U - Height
JH149A
See Configuration
NOTE: 1,2
Configuration Rules:
Page 8
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Configuration
Note 1
Note 2
Remarks:
The following Transceivers install into this Switch: (SFP Ports)
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC BX 10-U Transceiver
HPE X120 1G SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP LC LH100 Transceiver
JD102B
JD120B
JD100A
JD101A
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD103A
The following Transceivers install into this Switch: (SFP+ Ports)
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC BX 10-U Transceiver
HPE X120 1G SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD092B
JD094B
JG081C
JH693A
JH694A
JH695A
Iris note - If the below cables are selected for the JH146A and JH148A, then 4 RJ
45 ports are disabled:
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper
JG329A
Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper
JG330A
Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper
JG331A
Splitter Cable
Box Level Integration CTO Models
CTO Solution SKU
HPE FlexNetwork 55xx Configure-to-order Switch Solution
• SSP trigger SKU
JG506A
CTO Switch Chassis
HPE FlexNetwork 5510 24G 4SFP+ HI 1-slot Switch
JH145A
Page 9
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Configuration
•
•
•
•
•
•
24 RJ-45 autosensing 10/100/1000 ports
4 fixed Gigabit Ethernet SFP+ ports
(min=0 \ max=4 SFP/SFP+ Transceivers)
1 port expansion module slots
Must select min 1 power supply
1U - Height
See Configuration
NOTE: 2, 10
HPE FlexNetwork 5510 48G 4SFP+ HI 1-slot Switch
• 48 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH146A
See Configuration
NOTE: 2, 10
HPE FlexNetwork 5510 24G PoE+ 4SFP+ HI 1-slot Switch
• 24 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH147A
See Configuration
NOTE: 2, 10
HPE FlexNetwork 5510 48G PoE+ 4SFP+ HI 1-slot Switch
• 48 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH148A
See Configuration
NOTE: 2, 10
HPE FlexNetwork 5510 24G SFP 4SFP+ HI 1-slot Switch
• 16 SFP fixed Gigabit Ethernet SFP ports (min=0 \ max=16 SFP Transceivers)
• 8 RJ-45/ SFP fixed combo ports (min=0 \ max=8 SFP Transceivers)
• 4 fixed SFP+ ports (min=0 \ max=4 SFP+ Transceivers)
• 1 open module slots, or a combination
• Must select min 1 power supply
• 1U - Height
JH149A
See Configuration
NOTE: 1, 2, 10
Configuration Rules:
Note 1
The following Transceivers install into this Switch: (SFP Ports)
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC BX 10-U Transceiver
JD102B
JD120B
JD100A
JD101A
JD118B
JD119B
JD089B
JD098B
Page 10
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Configuration
Note 2
HPE X120 1G SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP LC LH100 Transceiver
JD099B
JD062A
JD061A
JD063B
JD103A
The following Transceivers install into this Switch: (SFP+ Ports)
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC BX 10-U Transceiver
HPE X120 1G SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
JH693A
JH694A
JH695A
Note 10
If the Switch Chassis is to be Factory Integrated (CTO), Then the #0D1 is required
on the Switch Chassis and integrated to the JG506A - HPE 55xx CTO Switch
Solution. (Min 1/Max 1 Switch per SSP)
Remarks:
Iris note - If the below cables are selected for the JH146A and JH148A, then 4 RJ
45 ports are disabled:
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper
JG329A
Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper
JG330A
Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper
JG331A
Splitter Cable
Rack Level Integration CTO Models
Switch Chassis
HPE FlexNetwork 5510 24G 4SFP+ HI 1-slot Switch
• 24 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH145A
See Configuration
NOTE: 2, 10
Page 11
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Configuration
HPE FlexNetwork 5510 48G 4SFP+ HI 1-slot Switch
• 48 RJ-45 autosensing 10/100/1000 ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH146A
See Configuration
NOTE: 2, 3, 10
HPE FlexNetwork 5510 24G PoE+ 4SFP+ HI 1-slot Switch
• 24 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH147A
See Configuration
NOTE: 2, 10
HPE FlexNetwork 5510 48G PoE+ 4SFP+ HI 1-slot Switch
• 48 RJ-45 autosensing 10/100/1000 PoE+ ports
• 4 fixed Gigabit Ethernet SFP+ ports
• (min=0 \ max=4 SFP/SFP+ Transceivers)
• 1 port expansion module slots
• Must select min 1 power supply
• 1U - Height
JH148A
See Configuration
NOTE: 2, 10
HPE FlexNetwork 5510 24G SFP 4SFP+ HI 1-slot Switch
• 16 SFP fixed Gigabit Ethernet SFP ports (min=0 \ max=16 SFP Transceivers)
• 8 RJ-45/ SFP fixed combo ports (min=0 \ max=8 SFP Transceivers)
• 4 fixed SFP+ ports (min=0 \ max=4 SFP+ Transceivers)
• 1 open module slots, or a combination
• Must select min 1 power supply
• 1U - Height
JH149A
See Configuration
NOTE: 1, 2, 10
Configuration Rules:
Note 1
Note 2
The following Transceivers install into this Switch: (SFP Ports)
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC BX 10-U Transceiver
HPE X120 1G SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP LC LH100 Transceiver
JD102B
JD120B
JD100A
JD101A
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD103A
The following Transceivers install into this Switch: (SFP+ Ports)
Page 12
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Configuration
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC BX 10-U Transceiver
HPE X120 1G SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
JD118B
JD119B
JD089B
JD098B
JD099B
JD062A
JD061A
JD063B
JD092B
JD094B
JD095C
JD096C
JD097C
JG081C
JH693A
JH694A
JH695A
Note 3
If this Switch is integrated into an SGI 8600 Rack(Q2P32A), then Min 2 // Max 2 of
the following PSUs must be selected(No Mixing)
HPE X361 150W 48-60VDC to 12VDC Power Supply
JD366B
HPE X361 150W 100-240VAC to 12VDC Power Supply
JD362B
Note 10
If HPE CTO Switch Chassis is selected for Rack Level Integration, Then the Switch
needs to integrate (with #0D1) to the Rack.
Remarks:
No Rail Kit required
Iris note - If the below cables are selected for the JH146A and JH148A, then 4 RJ
45 ports are disabled:
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper
JG329A
Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper
JG330A
Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper
JG331A
Splitter Cable
Enter the following menu selections as integrated to the CTO Model X above if order is factory built.
Modules
System (std 0 // max 1) User Selection (min 0 // max 1)
HPE FlexNetwork 5130/5510 10GBASE-T 2p Module
• No Transceivers
JH156A
HPE FlexNetwork 5130/5510 10GbE SFP+ 2p Module
• min=0 \ max=2 SFP+ Transceivers
JH157A
See Configuration
NOTE: 1
HPE FlexNetwork 5510 2-port QSFP+ Module
JH155A
Page 13
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Configuration
•
min=0 \ max=2 QSFP+ Transceivers
See Configuration
NOTE: 2
Configuration Rules:
Note 1
Note 2
The following Transceivers install into this Module (SFP+ Ports)
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X130 10G SFP+ LC LH80 tunable Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HPE X130 10G SFP+ LC LRM Transceiver
HPE X130 10G SFP+ LC LH 80km Transceiver
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
JD092B
JD094B
JL250A
JD095C
JD096C
JD097C
JG081C
JD093B
JG915A
JH693A
JH694A
JH695A
The following 40G Transceivers install into this Module: (Use #0D1 or #B01 if switch is CTO)
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
JG661A
HPE X140 40G QSFP+ MPO SR4 Transceiver
JG325B
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
JG709A
HPE X140 40G QSFP+ LC BiDi 100m MM Transceiver
JL251A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
JG326A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
JG327A
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
JG328A
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper
JG329A
Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper
JG330A
Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper
JG331A
Splitter Cable
HPE X140 40G QSFP+ MPO SR4 Campus-Transceiver
JH679A
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Campus-Transceiver
JH681A
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Campus-Transceiver
JH677A
HPE X140 40G QSFP+ LC BiDi 100m MM Campus-Transceiver
JH678A
HPE X240 40G QSFP+ to QSFP+ 1m Direct Attach Copper Campus-Cable
JH697A
HPE X240 40G QSFP+ to QSFP+ 3m Direct Attach Copper Campus-Cable
JH698A
HPE X240 40G QSFP+ to QSFP+ 5m Direct Attach Copper Campus-Cable
JH699A
HPE X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Campus-Cable
JH700A
Transceivers
SFP Transceivers
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
JD118B
JD119B
JD063B
JD062A
Page 14
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Configuration
HPE X120 1G SFP LC LH100 Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC BX 10-U Transceiver
HPE X120 1G SFP LC BX 10-D Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
JD103A
JD061A
JD089B
JD098B
JD099B
JD100A
JD102B
JD120B
JD101A
SFP+ Transceivers
HPE X130 10G SFP+ LC ER 40km Transceiver
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LRM Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X130 10G SFP+ LC LH 80km Transceiver
HPE X130 10G SFP+ LC LH80 tunable Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
JG234A
JD092B
JD093B
JD094B
JG915A
JL250A
JD095C
JD096C
JD097C
JG081C
JH693A
JH694A
JH695A
QSFP+ Transceivers
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Transceiver
HPE X140 40G QSFP+ MPO SR4 Transceiver
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Transceiver
HPE X140 40G QSFP+ LC BiDi 100m MM Transceiver
HPE FlexNetwork X240 40G QSFP+ QSFP+ 1m Direct Attach Copper Cable
HPE FlexNetwork X240 40G QSFP+ QSFP+ 3m Direct Attach Copper Cable
HPE FlexNetwork X240 40G QSFP+ QSFP+ 5m Direct Attach Copper Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Splitter Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
HPE X140 40G QSFP+ MPO SR4 Campus-Transceiver
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Campus-Transceiver
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Campus-Transceiver
HPE X140 40G QSFP+ LC BiDi 100m MM Campus-Transceiver
HPE X240 40G QSFP+ to QSFP+ 1m Direct Attach Copper Campus-Cable
HPE X240 40G QSFP+ to QSFP+ 3m Direct Attach Copper Campus-Cable
HPE X240 40G QSFP+ to QSFP+ 5m Direct Attach Copper Campus-Cable
HPE X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Campus-Cable
JG661A
JG325B
JG709A
JL251A
JG326A
JG327A
JG328A
JG329A
JG330A
JG331A
JH679A
JH681A
JH677A
JH678A
JH697A
JH698A
JH699A
JH700A
Cables
Console Cables
Page 15
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Configuration
(std 0 // max 99) User Selection (min 0 // max 99) per switch
Aruba X2C2 RJ45 to DB9 Console Cable
JL448A
Multi-Mode Cables
(std 0 // max 99) User Selection (min 0 // max 99) per switch
HPE LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 1.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 2.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 5.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 15.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 30.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 50.0m 1-Pack Fiber Optic Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
AJ833A
AJ834A
AJ835A
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
Internal Power Supplies
System (std 0 // max 2) User Selection (min 1 // max 2) per switch enclosure
HPE X361 150W 48-60VDC to 12VDC Power Supply
JD366B
See Configuration
NOTE: 1
HPE X361 150W 100-240VAC to 12VDC Power Supply
• includes 1 x c13, 910w
JD362B
See Configuration
NOTE: 1, 3, 4
PDU Cable NA/MEX/TW/JP
• C13 PDU Jumper Cord (NA/MEX/TW/JP)
JD362B#B2B
PDU Cable ROW
• C13 PDU Jumper Cord (ROW)
JD362B#B2C
High Volt Switch to Wall Power Cord
• HPE 2.3M C13 to NEMA L6-20P Power Cord(J9936A)
JD362B#B2E
No Power Cord
• No Localized Power Cord Selected
JD362B#AC3
HPE X362 720W 100-240VAC to 56VDC PoE Power Supply
• includes 1 x c13, 720w
PDU Cable NA/MEX/TW/JP
JG544A
See Configuration
NOTE: 2, 3, 4
JG544A#B2B
Page 16
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Configuration
•
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
• C15 PDU Jumper Cord (ROW)
JG544A#B2C
High Volt Switch to Wall Power Cord
• NEMA L6-20P Cord (NA/MEX/JP/TW)
JG544A#B2E
HPE X362 1110W 115-240VAC to 56VDC PoE Power Supply
• includes 1 x c13, 1100w
JG545A
See Configuration
NOTE: 2, 3, 4
PDU Cable NA/MEX/TW/JP
• C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG545A#B2B
PDU Cable ROW
• C15 PDU Jumper Cord (ROW)
JG545A#B2C
High Volt Switch to Wall Power Cord
• NEMA L6-20P Cord (NA/MEX/JP/TW)
JG545A#B2E
Configuration Rules:
Note 1
This power supply is only supported on JH145A, JH146A, and JH149A
Note 2
This power supply is only supported on JH147A and JH148A,
Note 3
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU
Power Cord). (See Localization Menu)
Note 4
When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the
Defaulted Power Cable option on the Switches/Routers.
Remarks:
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America,
Mexico, Taiwan, and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack
Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson
Default for BTO and Box Level CTO)
High Volt Switch/Router/Power Supply to Wall Power Cord - #B2E Option.
(Offered only in North America, Mexico, Taiwan, and Japan)
NOTE* DC Power Supply does not require Localization (CLIC Rule does not require
looking for Localization)
NOTE* Mixing of power supplies is supported
Page 17
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Technical Specifications
HPE FlexNetwork 5510 24G 4SFP+ HI 1-slot Switch (JH145A)
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
I/O ports and slots
100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Media Type: Auto-MDIX;
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports or 2 40GbE ports, with optional
module
Additional ports and slots 1 dual-personality (RJ-45 or mini USB) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
Power supplies
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Fan tray
17.32(w) x 14.17(d) x 1.72(h) in (44.00 x 36.00 x 4.37 cm) (1U
Physical characteristics Dimensions
height)
16.53 lb (7.5 kg) shipping weight
Weight
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Memory and processor
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
IPv6 Ready Certified
Performance
1000 Mb Latency
< 5 μs
10 Gbps Latency
< 3 μs
up to 214 Mpps
Throughput
Routing/Switching capacity 288 Gbps
32768 entries (IPv4), 16384 entries (IPv6)
Routing table size
32768 entries
MAC address table size
32°F to 113°F (0°C to 45°C)
Environment
Operating temperature
Operating relative humidity 10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
temperature
5% to 95%, noncondensing
Nonoperating/Storage
relative humidity
Low-speed fan: 52.8 dB, High-speed fan: 66.7 dB; ISO 7779
Acoustic
50/60 H
Electrical characteristics Frequency
Maximum heat dissipation 365 BTU/hr (385.08 kJ/hr), Ranges from 167 BTU/hr to 392 BTU/hr,
depending on power supply configuration
100 - 240 VAC, rated (90 - 264 VAC, max)
Voltage
-48 to -60 VDC, rated (-36 to -72 VDC, max)
(depending on power supply chosen)
107 W
Maximum power rating
55 W
Idle power
Notes
Idle power is the actual power consumption of the device with no
ports connected.
Maximum power rating and maximum heat dissipation are the worstcase theoretical maximum numbers provided for planning the
Page 18
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
Safety
Emissions
Immunity
Management
Services
infrastructure with fully loaded PoE (if equipped), 100% traffic, all
ports plugged in, and all modules populated.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser ProductsPart 2; IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS
Compliance; AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.42009; EN 61000-3-3:2008; VCCI V-3/2012.04; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN
61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; CISPR 22:2008
Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI
V-3/2013.04 Class A
EN 55024
Generic
EN300 386
ESD
IMC - Intelligent Management Center; Command-line interface; SNMP manager
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexNetwork 5510 48G 4SFP+ HI 1-slot Switch (JH146A)
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
I/O ports and slots
100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Media Type: Auto-MDIX; Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports or 2 40GbE ports, with optional
module
Additional ports and slots 1 dual-personality (RJ-45 or mini USB) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
Power supplies
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Fan tray
17.32(w) x 14.17(d) x 1.72(h) in (44.0 x 36.0 x 4.37 cm) (1U height)
Physical characteristics Dimensions
16.53 lb (7.5 kg)
Weight
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Memory and processor
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
IPv6 Ready Certified
Performance
1000 Mb Latency
< 5 μs
10 Gbps Latency
< 3 μs
up to 250 Mpps
Throughput
Routing/Switching capacity 336 Gbps
32768 entries (IPv4), 16384 entries (IPv6)
Routing table size
32768 entries
MAC address table size
32°F to 113°F (0°C to 45°C)
Environment
Operating temperature
Operating relative humidity 10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
temperature
Page 19
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
Electrical characteristics
Safety
Emissions
Immunity
Management
Services
Nonoperating/Storage
relative humidity
Acoustic
Frequency
Maximum heat dissipation
5% to 95%, noncondensing
Low-speed fan: 49.9 dB, High-speed fan: 64.8 dB; ISO 7779
50/60 Hz
238 BTU/hr (686.81 kJ/hr), Ranges from 201 BTU/hr to 443 BTU/hr,
depending on power supply configuration
100 - 240 VAC, rated (90 - 264 VAC, max)
Voltage
-48 to -60 VDC, rated (-36 to -72 VDC, max)
(depending on power supply chosen)
150 W
Maximum power rating
70 W
Idle power
Notes
Idle power is the actual power consumption of the device with no
ports connected.
Maximum power rating and maximum heat dissipation are the
worst-case theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all
ports plugged in, and all modules populated.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser ProductsPart 2; IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS
Compliance; AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.42009; EN 61000-3-3:2008; VCCI V-3/2012.04; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN
61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; CISPR 22:2008
Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI
V-3/2013.04
Class A
EN 55024
Generic
EN300 386
ESD
IMC - Intelligent Management Center; Command-line interface; SNMP manager
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexNetwork 5510 24G PoE+ 4SFP+ HI 1-slot Switch (JH147A)
24 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
I/O ports and slots
100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Media Type: Auto-MDIX;
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only; Ports 1 - 8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports or 2 40GbE ports, with optional
module
Additional ports and slots 1 dual-personality (RJ-45 or mini USB) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
Power supplies
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Fan tray
17.32(w) x 18.11(d) x 1.72(h) in (43.99 x 46 x 4.37 cm) (1U height)
Physical characteristics Dimensions
27.56 lb (12.5 kg) shipping weight
Weight
Page 20
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
Memory and processor
Mounting and enclosure
Performance
Environment
Electrical characteristics
Safety
Emissions
Immunity
Management
Services
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
IPv6 Ready Certified
1000 Mb Latency
< 5 μs
10 Gbps Latency
< 3 μs
up to 214 Mpps
Throughput
Routing/Switching capacity 288 Gbps
32768 entries (IPv4), 16384 entries (IPv6)
Routing table size
32768 entries
MAC address table size
32°F to 113°F (0°C to 45°C)
Operating temperature
Operating relative humidity 10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
temperature
5% to 95%, noncondensing
Nonoperating/Storage
relative humidity
Low-speed fan: 57.6 dB, High-speed fan: 66.9 dB; ISO 7779
Acoustic
50/60 Hz
Frequency
Maximum heat dissipation 2217 BTU/hr (3599.66 kJ/hr), Ranges from 228 BTU/hr to 3412
BTU/hr, depending on power supply configuration
100 - 240 VAC, rated (90 - 264 VAC, max)
Voltage
650 W
Maximum power rating
67 W
Idle power
740 W PoE+
PoE power
Notes
Idle power is the actual power consumption of the device with no
ports connected.
Maximum power rating and maximum heat dissipation are the
worst-case theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all
ports plugged in, and all modules populated.
PoE+ power range is from 450W to 740W. PoE+ power is the power
supplied by the internal power supply(ies). It is dependent on the
type and quantity of power supplies. Device supports 1 or 2 internal
modular power supplies.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser ProductsPart 2; IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS
Compliance; AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.42009; EN 61000-3-3:2008; VCCI V-3/2012.04; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN
61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; CISPR 22:2008
Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI
V-3/2013.04 Class A
EN 55024
Generic
EN300 386
ESD
IMC - Intelligent Management Center; Command-line interface; SNMP manager
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
Page 21
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Technical Specifications
HPE FlexNetwork 5510 48G PoE+ 4SFP+ HI 1-slot Switch (JH148A)
48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type
I/O ports and slots
100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASETX: half or full; 1000BASE-T: full only; Ports 1 - 8 support MACSec
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports or 2 40GbE ports, with optional
module
Additional ports and slots 1 dual-personality (RJ-45 or mini USB) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
Power supplies
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Fan tray
17.32(w) x 18.11(d) x 1.72(h) in (43.99 x 46 x 4.37 cm) (1U height)
Physical characteristics Dimensions
27.56 lb (12.5 kg) shipping weight
Weight
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Memory and processor
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
IPv6 Ready Certified
Performance
1000 Mb Latency
< 5 μs
10 Gbps Latency
< 3 μs
up to 250 Mpps
Throughput
Routing/Switching capacity 336 Gbps
32768 entries (IPv4), 16384 entries (IPv6)
Routing table size
32768 entries
MAC address table size
32°F to 113°F (0°C to 45°C)
Environment
Operating temperature
Operating relative humidity 10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
temperature
5% to 95%, noncondensing
Nonoperating/Storage
relative humidity
Low-speed fan: 57.6 dB, High-speed fan: 66.9 dB; ISO 7779
Acoustic
50/60 Hz
Electrical characteristics Frequency
Maximum heat dissipation 2286 BTU/hr (2411.73 kJ/hr), Heat dissipation ranges from 256
BTU/hr to 6142 BTU/hr, depending on power supply configuration
100 - 240 VAC, rated (90 - 264 VAC, max)
Voltage
670 W
Maximum power rating
75 W
Idle power
1440 W PoE+
PoE power
Notes
Idle power is the actual power consumption of the device with no
ports connected.
Maximum power rating and maximum heat dissipation are the
worst-case theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all
ports plugged in, and all modules populated.
PoE+ power range is from 450W to 1440W. PoE+ power is the
power supplied by the internal power supply(ies). It is dependent on
the type and quantity of power supplies.
Page 22
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
Safety
Emissions
Immunity
Management
Services
Device supports 1 or 2 internal modular power supplies.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser ProductsPart 2; IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS
Compliance; AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.42009; EN 61000-3-3:2008; VCCI V-3/2012.04; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN
61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; CISPR 22:2008
Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI
V-3/2013.04 Class A
EN 55024
Generic
EN300 386
ESD
IMC - Intelligent Management Center; Command-line interface; SNMP manager
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexNetwork 5510 24G SFP 4SFP+ HI 1-slot Switch (JH149A)
16 fixed Gigabit Ethernet SFP ports; Ports 1 - 8 support MACSec
I/O ports and slots
8 Combo GbE (SFP and RJ45) dual-personality 1000 Mbps port, IEEE 802.3ab Type 1000BASE-T);
Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only
4 SFP+ 10GbE ports
1 port expansion module slot
Supports a maximum of 6 SFP+ ports or 2 1/10GBASE-T ports or 2 40GbE ports, with optional
module
Additional ports and slots 1 dual-personality (RJ-45 or mini USB) serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
Power supplies
1 minimum power supply required (ordered separately)
Airflow direction is Front (port side) to Back (power cord side)
Fan tray
17.32(w) x 14.17(d) x 1.72(h) in (43.99 x 35.99 x 4.37 cm) (1U
Physical characteristics Dimensions
height)
16.53 lb (7.5 kg) shipping weight
Weight
2 GB SDRAM; Packet buffer size: 4 MB, 512 MB flash
Memory and processor
Mounting and enclosure Mounts in an EIA standard 19-inch telco rack or equipment cabinet (hardware included)
IPv6 Ready Certified
Performance
1000 Mb Latency
< 5 μs
10 Gbps Latency
< 3 μs
up to 214 Mpps
Throughput
Routing/Switching capacity 288 Gbps
32768 entries (IPv4), 16384 entries (IPv6)
Routing table size
32768 entries
MAC address table size
32°F to 113°F (0°C to 45°C)
Environment
Operating temperature
Operating relative humidity 10% to 90%, noncondensing
-40°F to 158°F (-40°C to 70°C)
Nonoperating/Storage
temperature
Page 23
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
Electrical characteristics
Safety
Emissions
Immunity
Management
Services
Nonoperating/Storage
relative humidity
Acoustic
Frequency
Maximum heat dissipation
5% to 95%, noncondensing
Low-speed fan: 50.5 dB, High-speed fan: 66.9 dB; ISO 7779
50/60 Hz
409 BTU/hr (431.49 kJ/hr), Heat dissipation ranges from 163 BTU/hr
to 498 BTU/hr, depending on power supply configuration
100 - 240 VAC, rated (90 - 264 VAC, max)
Voltage
-48 to -60 VDC, rated (-36 to -72 VDC, max)
(depending on power supply chosen)
120 W
Maximum power rating
48 W
Idle power
Notes
Idle power is the actual power consumption of the device with no
ports connected.
Maximum power rating and maximum heat dissipation are the
worst-case theoretical maximum numbers provided for planning the
infrastructure with fully loaded PoE (if equipped), 100% traffic, all
ports plugged in, and all modules populated.
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of Laser ProductsPart 2; IEC 60950-1; EN 60950-1; CAN/CSA-C22.2 No. 60950-1; FDA 21 CFR Subchapter J; ROHS
Compliance; AS/NZS 60950-1; GB 4943; EAC (EurAsian Conformity Certification)
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A; EN 61000-4-11:2004; ANSI C63.42009; EN 61000-3-3:2008; VCCI V-3/2012.04; EN 61000-3-2:2006+A1:2009+A2:2009 ; EN
61000-4-3:2006; EN 61000-4-4:2012; EN 61000-4-5:2006; EN 61000-4-6:2009; CISPR 22:2008
Class A; EN 55022:2010 Class A; EN 61000-4-29: 2000; CISPR 24:2010; EN 300 386 V1.6.1; VCCI
V-3/2013.04 Class A
EN 55024
Generic
EN300 386
ESD
IMC - Intelligent Management Center; Command-line interface; SNMP manager
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for
details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
Standards and protocols (applies to all products in series)
BGP
RFC 1657 Definitions of Managed Objects for BGPv4
RFC 1771 BGPv4
RFC 2385 BGP Session Protection via TCP MD5
RFC 2858 BGP-4 Multi-Protocol Extensions
Device Management
RFC 1155 Structure and Mgmt Information (SMIv1)
RFC 1157 SNMPv1/v2c
RFC 1305 NTPv3
RFC 2573 (SNMPv3 Applications)
RFC 2578-2580 SMIv2
RFC 2819 (RMON groups Alarm, Event, History and Statistics only)
RFC 3416 (SNMP Protocol Operations v2)
RFC 3417 (SNMP Transport Mappings)
HTML and telnet management
Multiple Configuration Files
SNMP v3 and RMON RFC support
Page 24
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
SSHv1/SSHv2 Secure Shell
TACACS/TACACS+
Web UI
General Protocols
IEEE 802.1ad Q-in-Q
IEEE 802.1ak Multiple Registration Protocol (MRP) and Multiple VLAN Registration Protocol (MVRP)
IEEE 802.1AX-2008 Link Aggregation
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q (GVRP)
IEEE 802.1Q VLANs
IEEE 802.1s Multiple Spanning Trees
IEEE 802.1v VLAN classification by Protocol and Port
IEEE 802.1w Rapid Reconfiguration of Spanning Tree
IEEE 802.1X PAE
IEEE 802.3 Type 10BASE-T
IEEE 802.3ab 1000BASE-T
IEEE 802.3ac (VLAN Tagging Extension)
IEEE 802.3ad Link Aggregation (LAG)
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at Power over Ethernet Plus
IEEE 802.3az Energy Efficient Ethernet
IEEE 802.3i 10BASE-T
IEEE 802.3u 100BASE-X
IEEE 802.3x Flow Control
IEEE 802.3z 1000BASE-X
RFC 768 UDP
RFC 783 TFTP Protocol (revision 2)
RFC 791 IP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 855 Telnet Option Specification
RFC 894 IP over Ethernet
RFC 925 Multi-LAN Address Resolution
RFC 950 Internet Standard Subnetting Procedure
RFC 951 BOOTP
RFC 959 - File Transfer Protocol (FTP)
RFC 1027 Proxy ARP
RFC 1042 IP Datagrams
RFC 1058 RIPv1
RFC 1071 Computing the Internet Checksum
RFC 1122 Requirements for Internet Hosts - Communication Layers
RFC 1123 Requirements for Internet Hosts
RFC 1141 Incremental updating of the Internet checksum
RFC 1166 - IP Addresses
RFC 1191 Path MTU discovery
RFC 1213 Management Information Base for Network Management of TCP/IP-based internets
RFC 1256 - ICMP Router Discovery Protocol (IRDP)
RFC 1305 NTPv3
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
Page 25
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
RFC 1533 DHCP Options and BOOTP Vendor Extensions
RFC 1542 BOOTP Extensions
RFC 1591 DNS (client only)
RFC 1643 - Definitions of Managed Objects for the Ethernet-like Interface Types
RFC 1723 RIP v2
RFC 1812 IPv4 Routing
RFC 1866 Hypertext Markup Language - 2.0
RFC 1887 An Architecture for IPv6 Unicast Address Allocation
RFC 1901 - Introduction to Community-based SNMPv2
RFC 1902-1907 - SNMPv2
RFC 2131 DHCP
RFC 2236 IGMP Snooping
RFC 2338 VRRP
RFC 2375 IPv6 Multicast Address Assignments
RFC 2462 IPv6 Stateless Address Autoconfiguration
RFC 2474 Definition of the Differentiated Services Field (DS Field) in the IPv4 and IPv6 Headers
RFC 2475 Architecture for Differentiated Services
RFC 2597 Assured Forwarding PHB Group
RFC 2616 Hypertext Transfer Protocol -- HTTP/1.1
RFC 2644 Directed Broadcast Control
RFC 2665 Definitions of Managed Objects for the Ethernet-like Interface Types
RFC 2668 Definitions of Managed Objects for IEEE 802.3 Medium Attachment Units (MAUs)
RFC 2711 IPv6 Router Alert Option
RFC 2784 Generic Routing Encapsulation (GRE)
RFC 2865 Remote Authentication Dial In User Service (RADIUS)
RFC 2866 RADIUS Accounting
RFC 2868 RADIUS Attributes for Tunnel Protocol Support
RFC 3046 - DHCP Relay Agent Information Option
RFC 3209 RSVP-TE Extensions to RSVP for LSP Tunnels
RFC 3246 Expedited Forwarding PHB
RFC 3410 Applicability Statements for SNMP
RFC 3414 User-based Security Model (USM) for version 3 of the Simple Network Management
Protocol (SNMPv3)
RFC 3415 View-based Access Control Model (VACM) for the Simple Network Management Protocol
(SNMP)
RFC 3416 Protocol Operations for SNMP
RFC 3417 Transport Mappings for the Simple Network Management Protocol (SNMP)
RFC 3418 Management Information Base (MIB) for the Simple Network Management Protocol
(SNMP)
RFC 3484 Default Address Selection for Internet Protocol version 6 (IPv6)
RFC 3493 Basic Socket Interface Extensions for IPv6
RFC 3542 Advanced Sockets Application Program Interface (API) for IPv6
RFC 3576 Ext to RADIUS (CoA only)
RFC 3580 - IEEE 802.1X Remote Authentication Dial In User Service (RADIUS) Usage Guidelines
RFC 3587 IPv6 Global Unicast Address Format
RFC 3596 DNS Extensions to Support IP Version 6
RFC 3623 Graceful OSPF Restart
RFC 3704 Unicast Reverse Path Forwarding (URPF)
RFC 3768 Virtual Router Redundancy Protocol (VRRP)
RFC 3810 Multicast Listener Discovery Version 2 (MLDv2) for IPv6
RFC 4090 Fast Reroute Extensions to RSVP-TE for LSP Tunnels
RFC 4113 Management Information Base for the User Datagram Protocol (UDP)
RFC 4213 Basic IPv6 Transition Mechanisms
RFC 4250 The Secure Shell (SSH) Protocol Assigned Numbers
RFC 4251 The Secure Shell (SSH) Protocol Architecture
Page 26
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
RFC 4252 The Secure Shell (SSH) Authentication Protocol
RFC 4253 The Secure Shell (SSH) Transport Layer Protocol
RFC 4254 The Secure Shell (SSH) Connection Protocol
RFC 4291 IP Version 6 Addressing Architecture
RFC 4443 Internet Control Message Protocol (ICMPv6) for the Internet Protocol Version 6 (IPv6)
Specification
RFC 4541 Considerations for Internet Group Management Protocol (IGMP) and Multicast Listener
Discovery (MLD) Snooping Switches
RFC 4575 A Session Initiation Protocol (SIP) Event Package for Conference State
RFC 4594 Configuration Guidelines for DiffServ Service Classes
RFC 4675 RADIUS VLAN & Priority
RFC 4750 OSPF Version 2 Management Information Base
RFC 4762 Virtual Private LAN Service (VPLS) Using Label Distribution Protocol (LDP) Signaling
RFC 5095 Deprecation of Type 0 Routing Headers in IPv6
802.1r - GARP Proprietary Attribute Registration Protocol (GPRP)
IP Multicast
RFC 1112 IGMPv1
RFC 2236 IGMPv2
RFC 2710 Multicast Listener Discovery (MLD) for IPv6
RFC 2858 Multiprotocol Extensions for BGP-4
RFC 3376 IGMPv3
RFC 3569 An Overview of Source-Specific Multicast (SSM)
RFC 3618 Multicast Source Discovery Protocol (MSDP)
RFC 3973 PIM Dense Mode
RFC 4601 PIM Sparse Mode
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2460 IPv6 Specification
RFC 2461 IPv6 Neighbor Discovery
RFC 2463 ICMPv6
RFC 2464 Transmission of IPv6 over Ethernet Networks
RFC 2545 Use of BGP-4 Multiprotocol Extensions for IPv6 Inter-Domain Routing
RFC 3162 RADIUS and IPv6
RFC 3306 Unicast-Prefix-based IPv6 Multicast Addresses
RFC 3307 IPv6 Multicast Address Allocation
RFC 3315 DHCPv6 (client and relay)
RFC 3484 Default Address Selection for IPv6
RFC 3736 Stateless Dynamic Host Configuration Protocol (DHCP) Service for IPv6
RFC 4291 IP Version 6 Addressing Architecture
RFC 4293 MIB for IP
RFC 4443 ICMPv6
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Auto-configuration
RFC 6724 Default Address Selection for Internet Protocol Version 6 (IPv6)
MIBs
RFC 1212 Concise MIB Definitions
RFC 1213 MIB II
RFC 1215 A Convention for Defining Traps for use with the SNMP
RFC 1493 Bridge MIB
RFC 1757 Remote Network Monitoring MIB
RFC 2096 IP Forwarding Table MIB
RFC 2233 Interface MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
Page 27
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Technical Specifications
RFC 2573 SNMP-Notification MIB
RFC 2573 SNMP-Target MIB
RFC 2574 SNMP USM MIB
RFC 2618 RADIUS Authentication Client MIB
RFC 2620 RADIUS Accounting Client MIB
RFC 2665 Ethernet-Like-MIB
RFC 2668 802.3 MAU MIB
RFC 2674 Definitions of Managed Objects for Bridges with Traffic Classes, Multicast Filtering, and
Virtual Extensions
RFC 2737 Entity MIB (Version 2)
RFC 2819 RMON MIB
RFC 2863 The Interfaces Group MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB
MPLS
RFC 2961 RSVP Refresh Overhead Reduction Extensions
RFC 3031 Multiprotocol Label Switching Architecture
RFC 3032 MPLS Label Stack Encoding
RFC 3036 LDP Specification
RFC 4762 Virtual Private LAN Service (VPLS) Using Label Distribution Protocol (LDP) Signaling
Network Management
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
RFC 1215 Convention for defining traps for use with the SNMP
RFC 2579 Textual Conventions for SMIv2
RFC 2580 Conformance Statements for SMIv2
RFC 2818 HTTP over TLS
RFC 2819 Four groups of RMON: 1 (statistics), 2 (history), 3 (alarm) and 9 (events)
RFC 6398 IP Router Alert Considerations and Usage
ANSI/TIA-1057 LLDP Media Endpoint Discovery (LLDP-MED)
SNMPv1/v2c/v3
OSPF
RFC 1587 OSPF NSSA
RFC 1850 OSPFv2 Management Information Base (MIB), traps
RFC 2328 OSPFv2
RFC 2370 OSPF Opaque LSA Option
QoS/CoS
RFC 2474 DS Field in the IPv4 and IPv6 Headers
RFC 3260 New Terminology and Clarifications for DiffServ
Security
IEEE 802.1X Port Based Network Access Control
RFC 1492 TACACS+
RFC 2138 RADIUS Authentication
RFC 2139 RADIUS Accounting
RFC 2865 RADIUS Authentication
RFC 2866 RADIUS Accounting
RFC 3260 New Terminology and Clarifications for DiffServ
RFC 4716 SSH Public Key File Format
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
Page 28
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Accessories
HPE FlexNetwork 5510 HI Switch Series accessories
Modules
HPE FlexNetwork 5510 2-port QSFP+ Module
HPE FlexNetwork 5130/5510 10GBASE-T 2p Module 1
HPE FlexNetwork 5130/5510 10GbE SFP+ 2p Module 1
JH155A
JH156A
JH157A
Transceivers
HPE X115 100M SFP LC BX 10-U Transceiver 2
HPE X115 100M SFP LC BX 10-D Transceiver 2
HPE X115 100M SFP LC FX Transceiver 2
HPE X110 100M SFP LC LX Transceiver 2
HPE X125 1G SFP LC LH40 1310nm Transceiver 3
HPE X120 1G SFP LC LH40 1550nm Transceiver 3
HPE X125 1G SFP LC LH70 Transceiver 3
HPE X120 1G SFP RJ45 T Transceiver 3
HPE X120 1G SFP LC BX 10-U Transceiver 3
HPE X120 1G SFP LC BX 10-D Transceiver 3
HPE X120 1G SFP LC LH100 Transceiver 3
HPE X120 1G SFP LC SX Transceiver 3
HPE X120 1G SFP LC LX Transceiver 3
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HPE X130 10G SFP+ LC ER 40km Transceiver 4
HPE X130 10G SFP+ LC LH 80km Transceiver 4
HPE X130 10G SFP+ LC LRM Transceiver 4
HPE X140 40G QSFP+ MPO SR4 Campus-Transceiver
HPE X240 40G QSFP+ to QSFP+ 1m Direct Attach Copper Campus-Cable
HPE X240 40G QSFP+ to QSFP+ 3m Direct Attach Copper Campus-Cable
HPE X240 40G QSFP+ to QSFP+ 5m Direct Attach Copper Campus-Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 1m Direct Attach Copper Splitter Cable
HPE X240 40G QSFP+ to 4x10G SFP+ 3m Direct Attach Copper Campus-Cable
HPE FlexNetwork X240 40G QSFP+ to 4x10G SFP+ 5m Direct Attach Copper Splitter Cable
HPE X140 40G QSFP+ LC LR4 SM 10km 1310nm Campus-Transceiver
HPE X140 40G QSFP+ MPO MM 850nm CSR4 300m Campus-Transceiver
HPE X130 10G SFP+ LC LH80 tunable Transceiver
HPE X140 40G QSFP+ LC BiDi 100m MM Campus-Transceiver
JD100A
JD101A
JD102B
JD120B
JD061A
JD062A
JD063B
JD089B
JD098B
JD099B
JD103A
JD118B
JD119B
JD092B
JD094B
JH693A
JH694A
JH695A
JG081C
JG234A
JG915A
JD093B
JH679A
JH697A
JH698A
JH699A
JG329A
JH700A
JG331A
JH677A
JH681A
JL250A
JH678A
Cables
Aruba X2C2 RJ45 to DB9 Console Cable
HPE LC to LC Multi-mode OM3 2-Fiber 0.5m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 1.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 2.0m 1-Pack Fiber Optic Cable
JL448A
AJ833A
AJ834A
AJ835A
Page 29
QuickSpecs
HPE FlexNetwork 5510 HI Switch Series
Accessories
HPE LC to LC Multi-mode OM3 2-Fiber 5.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 15.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 30.0m 1-Pack Fiber Optic Cable
HPE LC to LC Multi-mode OM3 2-Fiber 50.0m 1-Pack Fiber Optic Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
AJ836A
AJ837A
AJ838A
AJ839A
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
HPE FlexNetwork 5510 24G 4SFP+ HI 1-slot Switch (JH145A)
HPE X361 150W 100-240VAC to 12VDC Power Supply 5
HPE X361 150W 48-60VDC to 12VDC Power Supply 5
JD362B
JD366B
HPE FlexNetwork 5510 48G 4SFP+ HI 1-slot Switch (JH146A)
HPE X361 150W 100-240VAC to 12VDC Power Supply 5
HPE X361 150W 48-60VDC to 12VDC Power Supply 5
JD362B
JD366B
HPE FlexNetwork 5510 24G PoE+ 4SFP+ HI 1-slot Switch (JH147A)
HPE X362 720W 100-240VAC to 56VDC PoE Power Supply 5
HPE X362 1110W 115-240VAC to 56VDC PoE Power Supply 5
JG544A
JG545A
HPE FlexNetwork 5510 48G PoE+ 4SFP+ HI 1-slot Switch (JH148A)
HPE X362 720W 100-240VAC to 56VDC PoE Power Supply 5
HPE X362 1110W 115-240VAC to 56VDC PoE Power Supply 5
JG544A
JG545A
HPE FlexNetwork 5510 24G SFP 4SFP+ HI 1-slot Switch (JH149A)
HPE X361 150W 100-240VAC to 12VDC Power Supply 5
HPE X361 150W 48-60VDC to 12VDC Power Supply 5
JD362B
JD366B
Module supports MACsec
Supported only on JH149A (HPE 5510 24G SFP 4SFP+ HI 1-Slot Switch) and only in 1G downlink configuration
3
Transceiver cannot be used on optional module JH157A (HPE 5130/5510 10GbE SFP+ 2-port Module)
4
Supported only on optional module JH157A
5
Products covered by 1 year warranty. See details at www.hpe.com/networking/warrantyquickref
1
2
Page 30
HPE FlexNetwork 5510 HI Switch Series
QuickSpecs
Summary of Changes
Date
18-Dec-2017
Action
Changed
Description of Change
Configuration section updated
Changed
Configuration section updated
Added
SKU added: JL448A
09-Jan-2017
Version History
From Version 12 to
13
From Version 11 to
12
From Version 10 to
11
From Version 9 to 10
Added
03-Oct-2016
19-Aug-2016
From Version 8 to 9
From Version 7 to 8
Added
Changed
01-Aug-2016
From Version 6 to 7
20-May-2016
08-Apr-2016
From Version 5 to 6
From Version 4 to 5
Added
Changed
Changed
Changed
16-Feb-2016
08-Jan-2016
11-Dec-2015
From Version 3 to 4
From Version 2 to 3
From Version 1 to 2
Changed
Changed
Changed
SKUs added: JH677A, JH678A, JH679A, JH680A, JH681A,
JH693A, JH694A, JH695A, JH696A, JH697A, JH698A,
JH699A, JH700A
SKUs added: JD362B, JD366B
Updates made on Standards and protocols, Configuration and
Accessories
SKU added: JL250A
Updates made on Technical Specifications
Updates made on Technical Specifications and Accessories
Changes made on Configuration section, SKUs descriptions
updated
Configuration and Standards and protocols updated
Accessories section updated
Transceivers updated.
04-Dec-2017
03-Jul-2017
Sign up for updates
© Copyright 2017 Hewlett Packard Enterprise Development LP. The information contained herein is
subject to change without notice. The only warranties for Hewlett Packard Enterprise products and
services are set forth in the express warranty statements accompanying such products and services.
Nothing herein should be construed as constituting an additional warranty. Hewlett Packard Enterprise
shall not be liable for technical or editorial errors or omissions contained herein.
To learn more, visit: http://www.hpe.com/networking
c04843027 - 15440 - Worldwide - V13 - 18-December-2017
Page 31