Installation & Maintenance Manual
PL42VO
28,000 btu/hr Natural Gas or Propane Gas
PL60VO
47,000 btu/hr Natural Gas or Propane Gas
Outdoor Gas Fireplace
• Theinstallationofthisfireplacemustbedonebyaqualifiedand
certifiedgasapplianceinstaller.
®
C
DANGER
US
CARBON MONOXIDE HAZARD
Thisappliancecanproducecarbon
monoxide,whichhasnoodor.
Usingitinanenclosedspacecan
killyou.
Neverusethisapplianceinan
enclosedspacesuchasacamper,
tent,carorhome.
• Checklocalcodesandreadallinstructionspriortoinstallation.
• Installer:leavethismanualwiththeappliance.
• Consumer:retainthismanualforfuturereference.
DANGER
Ifyousmellgas:
• Shutoffgastotheappliance.
• Extinguishanyopenflame.
• Ifodorcontinues,keepawayfromtheapplianceand
immediatelycallyourgassupplierorfiredepartment.
WARNING
WARNING:ForOutdoorUseOnly.
Donotstoreorusegasoline,orotherflammablevaporsand
liquids,inthevicinityofthisoranyotherappliance.
Apropane-cylindernotconnectedforuseshallnotbe
storedinthevicinityofthisoranyotherappliance.
WARNING
Improperinstallation,adjustment,alteration,serviceor
maintenancecancauseinjuryorpropertydamage.
Readtheinstallation,operating,andmaintenanceinstructions
thoroughlybeforeinstallingorservicingthisequipment.
Page 1
XG0219 - 170829
General Information & Safety
Contents
ConditionsandLimitations......................................................................................................... 3
GettingStarted............................................................................................................................. 4
Gaslineandconnection:..................................................................................................... 4
Electrical:............................................................................................................................. 4
SafeOperatingPractices............................................................................................................. 5
Certification................................................................................................................................. 6
RatingPlateLocation:......................................................................................................... 6
ExpandedRatingPlateLocation:........................................................................................ 6
ApplianceCertification................................................................................................................ 7
Certification......................................................................................................................... 7
InstallationStandards:....................................................................................................... 7
HighAltitudeInstallations:.................................................................................................. 7
OperationalWarnings.................................................................................................................. 7
Dimensions.................................................................................................................................. 8
PL42VODimensions............................................................................................................. 8
ControlBoxDimensions...................................................................................................... 8
LocationConsiderations.............................................................................................................. 9
ExplodedPartView.................................................................................................................... 10
ToolsandSuppliesrequired...................................................................................................... 10
ToolList.............................................................................................................................. 10
SupplyList......................................................................................................................... 10
Gassupplyrequirements.......................................................................................................... 11
ElectricalRequirements............................................................................................................ 11
Framing...................................................................................................................................... 12
In The Wall Installation...................................................................................................... 12
Standalone......................................................................................................................... 12
Clearances................................................................................................................................. 13
Mantels&Surrounds......................................................................................................... 13
ClearanceSpecifications................................................................................................... 13
Finishing..................................................................................................................................... 14
Standalone......................................................................................................................... 14
In The Wall Installation...................................................................................................... 14
Fireplace............................................................................................................................ 14
FireplaceFacing................................................................................................................ 14
MountingtheFireplaceControlBox................................................................................. 15
Wiring................................................................................................................................. 15
WiringInstructions............................................................................................................ 17
WiringInstructions............................................................................................................ 18
LEDStripInstructions........................................................................................................ 19
Gasconnection.......................................................................................................................... 20
Installing&RemovingtheDoor................................................................................................ 21
Removingthedoor............................................................................................................ 21
InstallingtheDoor............................................................................................................. 21
InstallingtheFirestones............................................................................................................ 22
InstallingOptionalMedia.......................................................................................................... 23
InstallingOptionalSpeckledStones................................................................................ 23
InstallingOptionalDriftwoodLogSet............................................................................... 23
InstallingOptionalMedia.......................................................................................................... 24
Page 2
Startupandinitialoperation......................................................................................................25
LEDOperationVerification–Applicableiflightkit(MCLEDVO)isinstalled....................25
InitialFireplaceOperationVerification–Ifgassupplyisconnected...............................25
InitialFireplaceOperationVerification–Ifgassupplynotyetconnected......................25
OptimizingtheFanSpeed.................................................................................................25
OperatingtheFireplace..............................................................................................................26
Remote........................................................................................................................................28
Receiver..............................................................................................................................28
Installation .........................................................................................................................28
GeneralInformation............................................................................................................29
LearningRemotetoReceiver.............................................................................................29
SystemCheck.....................................................................................................................29
RemoteWallClip.................................................................................................................29
RemoteLayout:...................................................................................................................30
Howtooperate:...................................................................................................................30
ChangingtheTemperatureScale:......................................................................................31
ChangingtheChildproofLock:...........................................................................................31
BatteryLife.........................................................................................................................32
Troubleshooting..................................................................................................................32
LEDRemoteControlOperation...................................................................................................33
Programming(CodeClearingandCodeMatching)...........................................................33
Installing&RemovingtheScreen..............................................................................................34
ReplacementScreens:........................................................................................................34
Troubleshootingguide................................................................................................................35
Maintenance/CleaningInstructions.........................................................................................36
AppendixA:Warranty.................................................................................................................37
Amendment.................................................................................................................................38
XG0219 - 170829
General Information & Safety
Montigo products are designed with superior components and materials, and are assembled by trained craftsmen who take great pride in their work.
Every component has been thoroughly inspected by a qualified technician before packaging and shipping to ensure that you, the customer, receive
the quality product you expect from Montigo.
ConditionsandLimitations
Montigo warrants its products against manufacturing defects to the
original homeowner only, provided that the purchase was made through
an authorized Montigo dealer and is subject to the following conditions
and limitations:
• This warranty defines the obligation and liability of Montigo with respect
to the Montigo fireplace and any other warranties expressed or implied
with respect to this product, its components or accessories are
excluded.
• This limited warranty does not cover damages caused by misuse, lack
of maintenance, grease fires, hostile environments, accident, alterations,
abuse or neglect and parts installed from other manufacturers will nullify
this warranty. Discoloration to plastic parts from chemical cleaners or
UV exposure is not covered by this warranty.
• Montigo neither assumes, nor authorizes any third party to assume, on
its behalf, any other liabilities with respect to the sale of this product.
• This limited warranty further does not cover any scratches, dents,
painted finishes, corrosion or discoloring by heat, abrasive and chemical
cleaners, nor chipping on porcelain enamel parts.
• Should deterioration of parts occur to the degree of non-performance
(rusted through or burnt through) within the duration of the warranted
coverage, a replacement part will be provided.
• After the first year, with respect to this Limited Warranty Montigo may, at
its discretion, fully discharge all obligations with respect to this warranty
by refunding to the original warranted purchaser the wholesale price of
any warranted but defective part(s).
• Montigo will not be responsible for: over firing, blow outs caused
by environmental conditions such as strong winds, or inadequate
ventilation,
• Any damages to the fireplace due to weather damage, hail, rough
handling, damaging chemicals or cleaners will not be the responsibility
of Montigo.
• The bill of sale or copy will be required together with a serial number
and a model number when making any warranty claims from Montigo.
• Montigo reserves the right to have its representative inspect any
product or part prior to honoring any warranty claim.
• Montigo shall not be liable for any transportation charges, labor costs,
or export duties.
• Montigo will not be responsible for the installation, labor or any other
costs or expenses related to the re-installation of a warranted part, and
such expenses are not covered by this warranty.
• Notwithstanding any provision contained in this Limited Warranty
Montigo’s responsibility under this warranty is defined as above and it
shall not in any event extend to any incidental, consequential, or indirect
damages.
WARNING
Foroutdooruseonly
Improper installation, adjustment, alteration, service or maintenance
can cause injury or property damage. Read the installation, operating
and maintenance instructions thoroughly before installing or servicing
this gas appliance.
XG0219 - 170829
Page 3
General Information & Safety
GettingStarted
Congratulationsonthepurchaseofa
MontigoFireplace
This product must be installed by a qualified installer.
• Do not install this model inside your home or any other confined space.
Electrical:
• The unit has built in fans to force out all of the heat right above the
glass window. Due to the glass window, this model is less sensitive to
moderate wind conditions.
• See location section for minimum outdoor space requirements.
• Select a location where you would like to install the control box that will
control this fireplace.
• Only burn this model with the glass front installed including the safety
screen protecting you from accidental contact with the hot glass.
• Install a 120 Volt cable from this box to the fireplace as per the electrical
diagram.
• Please unpack the fireplace and count all of the parts before you start
installing.
• Plug the power cable from your control box into a power supply that is
protected by a ground fault Breaker ( GFCI )
• Make sure you inspected this fireplace for possible freight damage as
well as scratches to the front portion of this fireplace. To clean the front
portion use a mild cleaning agent and wipe the stainless steel in the
direction of the grain.
• The toggle switch that is located on the left side of the control box will
start the blowers running.
• Build a structure of your choice around the fireplace with wood, steel
studs or any other conventional building materials.
• Safety switches in the bottom of the fireplace will sense the moving air
stream and activate the gas burner system.
• The electrical installation must comply with applicable standards.
• Select a location that will limit the exposure to strong winds.
• Follow the location section guidelines for installations in smaller spaces
Gaslineandconnection:
• Have a certified gas fitter install a gas line that will supply the required
level of gas to the left side of this fireplace with an accessible gas
service shut off valve. Gas supply as per the rating and pressures
shown in section "Gas Connection"
WARNING
CAUTION
Ensure that all power to the appliance is off at the electrical breaker
or fuse before beginning installation. Ensure gas is turned off at the
shutoff valve before beginning installation.
Page 4
During unpacking and assembly we recommended you wear work
gloves and safety glasses for your protection. Although we make every
effort to make the assembly process as problem free and safe as
possible, it is characteristic of fabricated steel parts that the edges and
corners might be sharp and could cause cuts if handled incorrectly.
XG0219 - 170829
General Information & Safety
SafeOperatingPractices
• Contact with this appliance can cause severe burns.
• Installation and repair must be done by a qualified service person.
The appliance should be inspected before use and at least annually
by a qualified service person. More frequent cleaning may be required
as necessary. It is imperative the control compartment, burners and
circulating air passageways of the appliance be kept clean.
• Clothing or other flammable materials should not be hung from the
appliance, or placed on or near the appliance.
• Any guard or other protective device removed for servicing the
appliance must be replaced prior to operating the appliance.
• Inspect the fuel supply connection for signs of leakage (including the
hose for Propane models) before each use of the appliance.
• Do not operate appliance before reading and understanding operating
instructions. Failure to operate appliance according to operating
instructions could cause fire or injury.
• To extend the life of your appliance, protect and cover it from the
elements when not in use.
• Risk of burns. The appliance should be turned off and cooled before
servicing.
• Inspect the burner before each use, burner must be replaced prior to
the appliance being put into operation if it is evident that the burner is
damaged. Replacement burner shall be one specified by Montigo.
• Do not install damaged, incomplete or substitute components.
• Young children should be carefully supervised when they are in the
area of the appliance. Toddlers, young children and others may
be susceptible to accidental contact burns. A physical barrier is
recommended if there are at risk individuals in the vicinity. To restrict
access to an appliance or stove, install an adjustable safety gate to
keep toddlers, young children and other at risk individuals out of the
vicinity and away from hot surfaces.
• Ensure you have incorporated adequate safety measures to protect
infants/toddlers from touching hot surfaces.
• Under no circumstances should this appliance be modified.
• Keep the packaging material out of reach of children and dispose of the
material in a safe manner. As with all plastic bags, these are not toys
and should be kept away from children and infants.
• Inspect the hose before each use of the appliance, if applicable. Hose
assembly must be replaced prior to the appliance being put into
operation if there is evidence of excessive abrasion or wear or if the
hose is damaged. Replacement hose assembly shall be that specified
by the Montigo.
• This product must be installed by a licensed plumber or gas fitter. See
appendix B for installation within the Commonwealth of Massachusetts
requirements.
• The appliance must be isolated from the gas supply piping system by
closing its individual manual shutoff valve during any pressure testing of
the gas supply piping system at test pressures equal to or less than 1/2
psi (3.5 kPa).
• Do not leave appliance unattended when in use.
• For outdoor use only.
• This unit is not for use with solid fuel.
• Improper installation, adjustment, alteration, service, or maintenance
can cause injury or property damage. Read the installation, operating
and maintenance instructions thoroughly before installing or servicing
this equipment.
• This appliance shall be used ONLY outdoors in a well-ventilated space
and shall NOT be used inside a building, garage, or any other enclosed
area.
XG0219 - 170829
Page 5
General Information & Safety
Certification












  
  
































 










   





LBA1200-V1.0 OutdoorCabanaFireHSI. 07.26.2016


Figure 4 Removal of lower air baffle
XG0219 - 170829
Page 6

A rating plate with additional information can be found secured with
velcro on the inside wall of the base of the firebox. To access the
rating plate, the door and lower air baffle can first be removed for
easier access. (See Door Installation/Removal section for instructions)


The rating plate can be found on the underside of the control box
cover.


FullRatingPlateLocation:


Figure 2 Control box rating plate


RatingPlateLocation:
Figure 1 Rating plate example
Figure 3 Full Rating plate
General Information & Safety
ApplianceCertification
OperationalWarnings
Certification
WARNING! Initial Lighting: When lit for the first time, the appliance
emits a slight odor. This is a normal temporary condition caused
by the “burn-off” of internal paints and lubricants used in the
manufacturing process and does not occur again. Simply run the main
burner on high for up to 8 hours.
Standard: ANSI Z21.97-2014/CSA 2.41-2014
TypeofAppliance: Outdoor Decorative Gas Appliance
Approvals: Approved for use in USA and Canada. Approved for use in the
State of Massachusetts
CertificationAgency: Canadian Standards Association (CSA)
WARNING! You must have clear and easy access to the manual
shut off valve AFTER the appliance is installed and connected to
the gas supply in order to safely turn off the gas to the appliance for
emergencies.
WARNING! Never use this appliance for other than the intended use.
InstallationStandards:
The installations must confirm with the requirements listed in this
document and to local codes. In the absence of local codes, it must
conform to the National Standards listed below. The appliance must be
electrically wired and grounded in accordance with the local codes and in
the absence of local codes must confirm to the National Standards listed
below.
USA: National Fuel Gas Code: ANSI 223.1/NFPA54
WARNING!
• Children and adults should be alerted to the hazards of high surface
temperatures and should stay away from the appliance to avoid
burns or clothing ignition.
• Children should be carefully supervised when they are in the area of
the appliance.
• Maintain 36" clearance from appliance front to any combustible
material.
National Electrical Code: NFPA 70
Canada: Natural Gas and Propane Installation Code CSAB149.1
Canadian Electrical Code CSA 22.1
• Clothing or other flammable materials should not be hung from the
appliance, or placed on or near the appliance.
MODEL
FUEL
ORIFICE
SIZE
MAX.INPUT
Btu/Hr
MINGASINLET
PRESSURES
• Any guard or protective device removed for servicing the appliance
must be replaced prior to operating the appliance.
PL42VONE
Natural Gas
1.45mmx3
28,000
5.5” W.C.
• Installation and repair should be done by a qualified service person.
PL42VOLE
Propane Gas
#64x3
28,000
11.0” W.C.
PL60VONE
Natural Gas
1.45mmx5
47,000
5.5” W.C.
PL60VOLE
Propane Gas
#64x5
47,000
11.0” W.C.
Figure 5 PL42VO, PL60VO Gas Standards
HighAltitudeInstallations:
If the heating value of the Natural Gas or Propane supply is derated to
compensate for the high altitude, the following requirements may not apply.
Please check with your local gas supplier or authority having jurisdiction
and contact your Montigo dealer.
• The appliance should be inspected before each use and at least
annually by a qualified service person. More frequent cleaning
may be required as necessary. It is imperative that the control
compartment, burners and circulating air passageways of the
appliance be kept clean.
NOTE The appliance has been designed with several safety features,
which include a safety valve. If the burner flame is extinguished the
appliance will automatically shut down.
This appliance is also equipped with two air proving switches
which will shut off gas to the burner if the air supply to the unit is
compromised.
USA:This appliance is approved for installations up to an altitude of 2000 ft.
(610 m) above sea level. For installations beyond this level, please contact
your Montigo dealer for high altitude conversion kits.
WARNING! Any modification to the appliance may compromise the
safety of this appliance.
CANADA:This appliance is approved for installations up to an altitude of
4500 ft. (1370m) above sea level. For installations beyond this level, please
contact your Montigo dealer for high altitude conversion kits.
Do not operate the appliance if any part has been under water.
Immediately call a qualified service technician to inspect the appliance
and replace any part of the control system and any gas control, which
has been underwater.
XG0219 - 170829
Page 7
Installation
Dimensions
43 3/4"
1111
July-19-16 9:10:47 AM
41 5/8"
1056
39 3/4"
1011
11 5/8"
294
42"
1067
22 1/4"
565
PROPRIETARY AND CONFIDENTIAL
26 7/8"
681
5 3/4"
146
4 7/8"
124
GAS
3/4"
19
1 1/4"
30
13 1/2"
343
3 1/4"
82
12 3/4"
325
12 1/2"
317
36 3/4"
932
ELECTRICAL
PL42VO Fireplace Dimensions (Tolerance ± ⅛") [3mm]
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
65 5/8"
PL60VODimensions
P42 Vent Free - OD
DATE
NAME
TMC 19/07/2016
REV.
SIZE DWG. NO.
A
P42VFO
A
SHEET 1 OF 2
SCALE 1:34 WEIGHT:
Y:\Products\Residential Products\R&D Projects\P42VFO\Cad Drawings\TMC April 2016 Revision with Rick\P42VFO
PL42VODimensions
63 3/4"
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
13 3/8"
13 3/8"
65 5/8"
13"
63 3/4"
Tuesday, August 29, 2017Tuesday,
9:04:00 AM
August 29, 2017 9:04:00 AM
The fireplace may be installed
in any location that maintains
proper clearances to air
conditioning ducts, electrical
wiring and plumbing. Safety, as
well as efficiency of operation,
should be considered when
selecting the fireplace location.
Select a location that does not
interfere with room traffic, and
has adequate ventilation as
described in the location section.
63 3/8"
13"
63 3/8"
67 5/8"
61 1/4"
29 1/4"
14 1/8"
28 3/8"
61 1/4"
Page 8
RIETARY AND CONFIDENTIAL
PROPRIETARY AND CONFIDENTIAL
28 3/8"
3 1/4"
GAS
4 7/8"
3 1/4"
GAS
4 7/8"
29 1/4"
14 1/8"
63 3/4"
27 1/4"
5 3/4"
27 1/4"
ELECTRICAL
11 1/4"
5 3/4"
PL60VO Fireplace Dimensions (Tolerance ± ⅛") [3mm]
63 3/4"
P6016VFONE
60in CabanaELECTRICAL
Fireplace
11 1/4"
DIM ARE IN INCHES
NAME
DATE
1/8
FRACTIONAL
DRAWN
CF
5/16/2017
.015
X.XX
5/18/2017
.005
X.XXX
CF
CHECKED
1
ANGULAR:
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
XG0219 - 170829
SIZE
B
DWG. NO.
SCALE:
P6016VFONE
P6016VFONE-Overall
60in 1:16
Cabana SHEET:
Fireplace
REV.
B
1 OF 1
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
DIM ARE IN INCHES
1/8
FRACTIONAL
.015
X.XX
.005
X.XXX
1
ANGULAR:
NAME
DATE
DRAWN
CF
5/16/2017
CHECKED
CF
5/18/2017
THIRD ANGLE PROJECTION
SIZE
B
DWG. NO.
P6016VFONE-Overall
REV.
Products\Residential
Y:\Products\Residential
Products\R&D Projects\P6016VONE\CAD
Products\R&D Projects\P6016VONE\CAD
Files\P6016VFONE-Overall
Files\P6016VFONE-Overall
67 5/8"
Installation
ControlBoxDimensions
15
6 16 "
27
8 64 "
53
3 64 "
19
6 64 "
21
64 "
19
64 "
33
5 64 "
USE #8 SCREWS
Use
screws for
FOR MOUNTING
mounting
1
2"
15
3 16 "
15
4 16 "
3
16 " MOUNTING HOLES
Use #8 screws for mounting
USE
#8 SCREWS FOR MOUNTING
OVERALL
DIMENSIONS
Overall
dimentions
MOUNTING
DIMENSIONS
Mounting
dimentions
Control Box Dimensions (Tolerance ± ⅛") [3mm]
XG0219 - 170829
Page 9
Installation
LocationConsiderations
The fireplace is designed for outdoor use up to a temperature of -40
deg F and may be installed as a standalone unit or built into an outside
wall. It may be installed in covered or screened porches that meet these
minimum requirements:
With walls on all sides, but at
least one permanent opening at
ground level and no overhead
cover.
• For covered porches, a minimum of ONE full side and ONE HALF
side (top portion of the wall) must be open to outside ventilation.
• For screened porches, a minimum of TWO full sides must be
screened with > 75% open area screen.
• Minimum Ceiling Height – 36 inches from the top of the fireplace
opening.
• Minimum Distance to Combustibles in the front – 36 inches from the
screen surface
Figure 6
• Mantle and side wall restrictions- see the finishing section
• Clearance from Grade to fireplace opening- 12 inches (for USA). 0
inches for Canada
If this appliance is installed into a wall, you must:
• Provide access to the gas shutoff valve
• Flash the front perimeter of the appliance in accordance with
regional requirements using exterior caulking or appropriate
materials to prevent the penetration of water around the appliance
into the wall. Considerations must be taken to manage the
water that may penetrate through the appliance to prevent water
accumulation and flooding at the bottom of the fireplace enclosure.
The fireplace enclosure has water drainage holes and must be
installed with proper drainage. Montigo encourages you to consult
your Building Envelope Engineer or Waterproofing Consultant for
further recommendations.
Figure 7
Figure 8
Within a partial enclosure which includes an overhead cover and no more
than two sidewalls. These sidewalls may be parallel, as in a breezeway, or
at right angles to each other.
This appliance may be installed on a wood or combustible deck.
Refer to Framing section for framing dimensions and clearances.
Installation MUST comply with local, regional, state and national codes
and regulations. Consult authorities having jurisdiction over restrictions,
installation inspections and permits
A three sided enclosure must
feature 30 percent or more of the
upper area of the enclosure is
permanently open.
Figure 9
Page 10
XG0219 - 170829
Installation
ExplodedPartView
SCREEN
November-15-16 9:37:02 AM
MAIN ASSY
SCREEN
MAIN ASSEMBLY
WINDOW
WINDOW
BURNER TRAY
BURNER TRAY
LED ASSY
VACUUM TUBING
ASSY
PROPRIETARY AND CONFIDENTIAL
BURNER ASSEMBLY
BURNER
ASSY
VACUUM SWITCH
ASSY
FANS
FANS
ToolsandSuppliesrequired
VACUUM SWITCH ASSEMBLY
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
P42 Vent Free - OD
DATE
NAME
TMC 28-Jul-16
REV.
SIZE DWG. NO.
A
SCALE 1:8
A
P42VFO
SHEET 1 OF 2
WEIGHT:
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
The list below is only for guidance, please review the instructions fully before installation.
ToolList
SupplyList
• Phillips head screwdriver
• Non-corrosive leak test solution
• Wrenches (5/8”, 1”, and 8mm)
• Control box mounting screws #8
• Voltmeter
• Fireplace mounting screws
• 3/16” Allen key
• 3 Conductor outdoor power cable 18AWG (Live, Neutral, Ground)
(30ft. or as required)
• 1/4" barb x 1/8” MPT fitting, with corresponding deep socket
• Manometer (to measure gas pressures)
XG0219 - 170829
Page 11
Y:\Products\Residential Products\R&D Projects\PL42VO\Cad Drawings\TMC April 2016 Revision with Rick\P42VFO
LED ASSEMBLY
Installation
ElectricalRequirements
EN
Have a certified gas fitter install a gas line that will supply the required
WINDOW
level of gas to the left side of this fireplace with an accessible gas service
BURNER TRAY
shut of valve. (shut off valve supplied)
MAIN ASSY
November-15-16 9:37:02 AM
Gassupplyrequirements
The fireplace is supplied with a waterproof control box which may be
mounted to an outside wall and a 3 foot powercord. A GFCI protected
plug to plugin the control box is required within 3 feet of the control box.
Montigo requires a service shut off valve be located in an accessible
location to isolate the gas supply.
Electrical Requirement for Control Box: 120VAC, 60 Hz, 5 A. GFCI
protected plug required.
Only install gas shut-off valves supplied or approved for use by the
state, province, or other governing body in which the fireplace is being
installed.
30 foot communication cable is supplied with the fireplace to connect
the control box to the fireplace.
Connect incoming gas line to the 1/2"or 3/8" gas inlet port.
LED ASSY
Keep the hose out of pathways where people may trip over it or in areas
where the hose may be subject to accidental damage
GASPRESSURE
3 conductor (Live, Neutral, and Ground) outdoor rated cable must be
supplied by the installer to provide 120VAC power from the control box
to the Fireplace (see figure below).
The optional Fireplace remote control comes in a separate water tight
box and can be mounted to the outside wall close to the fireplace control
box and needs to be wired to the control box using a 3-conductor
outdoor rated cable (supplied).
Pressurerequirementsare:
• Optimum appliance
performance requires proper
input pressures.
• Gas line sizing requirements
will be determined in ANSI
Z221.3 National Fuel Gas
Code in the USA and CAN/
CGA B149 in Canada.
Gas Pressure
Natural Gas
Propane
Minimum inlet
pressure
5.5in. w.c.
11in. w.c.
Manifold pressure
3.5in. w.c.
10in. w.c.
VACUUM TUBING
ASSY
BURNER ASSY
VACUUM SWITCH
ASSY
FANS
Figure 12 Gas connection
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
FigureP42
11 Electrical
Plate location
Vent Free
- OD
Remote
Control Box
DATE
NAME
TMC 28-Jul-16
SIZE DWG. NO.
A
SCALE 1:8
P42VFO
WEIGHT:
On/Off Toggle
Switch and fan
speed switch
REV.
SHEET 1 OF 2
A
Y:\Products\Residential Products\R&D Projects\PL42VO\Cad Drawings\TMC April 2016 Revision with Rick\P42VFO
Flexible gas connectors must not exceed 3 feet in length, unless
allowable within local regulations.
S DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
3 conductor
cable (supplied)
Gas Shut off
Valve (supplied)
3 conductor
cable
(supplied)
Electrical Cover
Plate
Power Outlet
with GFCI
3 conductor outdoor power cable 16AWG
(not supplied)
6 conductor cable 30ft supplied by Montigo
Gas Line
Page 12
Figure 10 Gas and electrical
XG0219 - 170829
Installation
PL42VOFraming
August-15-16 10:47:52 AM
PL42VOInTheWallandCornerInstallation
August-15-16 10:47:52 AM
ZERO CLEARANCE
AT CORNERS ONLY
26 15/16"
Figure 13 In the wall dimensions
REV.
SIZE DWG. NO.
P42VFO WALL INSTALLATION
A
SCALE 1:36 WEIGHT:
SHEET 2 OF 3
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
7"
PROPRIETARY AND CONFIDENTIAL
TypicalInstallationShown
Figure 16 Back
NAME
DATE
15-Aug-16
14 3/4"
SIZE DWG. NO.
A
FRAME
SCALE 1:24 WEIGHT:
REV.
SHEET 2 OF 3
Y REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
42 1/2"
REV.
SIZE DWG. NO.
A
P42VFO WALL INSTALLATION
SCALE 1:32 WEIGHT:
SHEET 3 OF 3
8"
7/
42
Figure 19 Corner dimensions
NOTE: Pre-fabricated stainless
steel enclosure for the PL42VO
is available from Montigo
(Product code: PL42VOBE)
DIM ARE IN INCHES
NAME
DATE
1/8
FRACTIONAL
DRAWN
CF
7/18/20
.015
X.XX
9/18/20
.005
X.XXX
CF
CHECKED
1
ANGULAR:
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
Add dimensions to this sheet
Create new sheet with fireplace
attached to framing
Add note to point to screws
Add view to show
cut-away
for
4
SCREWS
& BOTTOM
4 Screws
TopTOP
& Bottom
3 Screws
LeftLEFT
& Right
SCREWS
& RIGHT
drainiage holes
7
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PER
Frame in the enclosure for the
unit with framing materials.
The framed opening for the
assembled fireplace is 42’’
wide, x 27 1/2’’ high.
A
A
NOTE: When constructing the
framed opening, please ensure
there is access to install the
gas line and electrical when the
unit is installed.
SECTION A-A
Figure 18 Standalone Dimensions
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
DATE
NAME
TMC 15-Aug-16
NOTE: This unit features two
drainage holes on each of the
sides of the unit. Be sure to
plan a drain system for both
in the wall and standalone
installations.
SIZE DWG. NO.
A
STAND ALONE
SCALE 1:14 WEIGHT:
REV.
SHEET 3 OF 3
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
49"
42"
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
NAME
DATE
15-Aug-16
*12" minimum above grade is
required for US installations
SIZE DWG. NO.
A
FRAME
SCALE 1:24 WEIGHT:
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS
26 15/16"
7"
XG0219 - 170829
Figure 17 Standalone Dimensions
*
ings\MANUAL VIEWS\STAND ALONE\FRAME
PROPRIETARY AND CONFIDENTIAL
Figure 15 Front
DATE
NAME
TMC 15-Aug-16
"
16
7/
26 15/16
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PL42VOStandaloneInstallation
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
52"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
15 1/2"
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
62
August-15-16 2:16:01 PM
Figure 14 In the wall dimensions
DRAINAGE
HOLES
DRAINAGE HOLES
(BOTH
SIDES)
(BOTH SIDES)
DATE
NAME
TMC 15-Aug-16
42"
August-15-16 2:16:02 PM
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
PROPRIETARY AND CONFIDENTIAL
42 1/2"
PROPRIETARY AND CONFIDENTIAL
PROPRIETARY AND CONFIDENTIAL
14.750
44 SCREWS
TOP
& BOTTOM
Screws Top
& Bottom
Screws Left
& Right
33 SCREWS
LEFT
& RIGHT
\\pdm\shared$\Products\Residential Products\R&D Projects\PL42VO\Cad Drawings\MANUAL VIEWS\STAND ALONE\STAND ALONE
42.000
14 3/4"
48 1/8"
15 1/2"
49"
\\pdm\shared$\Products\Residential Products\R&D Projects\PL42VO\Cad Drawings\MANUAL VIEWS\WALL\P42VFO WALL INSTALLATION
52"
August-15-16 2:16:02 PM
42"
27.500
\\pdm\shared$\Products\Residential Products\R&D Projects\PL42VO\Cad Drawings\MANUAL VIEWS\STAND ALONE\FRAME
14 3/4"
\\pdm\shared$\Products\Residential Products\R&D Projects\PL42VO\Cad Drawings\MANUAL VIEWS\WALL\P42VFO WALL INSTALLATION
49"
32.500
Add dimensions to this sheet
Create new sheet with fireplace
attached to framing
Add note to point to screws
Add view to show cut-away for
drainiage holes
Page 13
Installation
PL60VOFraming
Thursday, August 31, 2017 9:33:34 AM
PL60VOInTheWallandCornerInstallation
Thursday, August 31, 2017 9:33:34 AM
ZERO CLEARANCE
AT CORNERS ONLY
Figure 21 In the wall dimensions
DIM ARE IN INCHES
NAME
DATE
1/8
FRACTIONAL
DRAWN
CF
7/19/2016
.015
X.XX
8/31/2017
.005
X.XXX
CF
CHECKED
1
ANGULAR:
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
(BOTH
SIDES)
60in
CABANA
(BOTH
SIDES)
CANADIAN HEATING
PRODUCTS
27342 GLOUCESTER WAY,
LANGLEY, BC, V4W 4A1
SIZE
A
DWG. NO.
1:32
SHEET:
6"
/1
15
87
"
66
Figure 20 In the wall dimensions
P6016VFONE WALL INSTALLATION
SCALE:
SCREWSTOP
TOP &
& BOTTOM
BOTTOM
44 SCREWS
LEFT &
& RIGHT
3 SCREWS
SCREWS LEFT
REV.
A
2 OF 3
Wall Installation
60in CABANA
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
DIM ARE IN INCHES
NAME
DATE
1/8
FRACTIONAL
DRAWN
CF
7/19/2016
.015
X.XX
8/31/2017
.005
X.XXX
CF
CHECKED
1
ANGULAR:
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
CANADIAN HEATING
PRODUCTS
THE
A
DWG. NO.
P6016VFONE WALL INSTALLATION
1:32
SCALE:
REV.
A
3 OF 3
SHEET:
Frame in the enclosure for the
unit with framing materials.
The framed opening for the
assembled fireplace is 66’’
wide, x 27 7/8’’ high.
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
PL60VOStandaloneInstallation
Monday, September 18, 2017 3:44:08 PM
Monday, September 18, 2017 3:50:32 PM
NOTE: When constructing the
framed opening, please ensure
there is access to install the
gas line and electrical when the
unit is installed.
Monday, September 18, 2017 3:50:32 PM
Monday, September 18, 2017 3:50:32 PM
TypicalInstallationShown
44 Screws
SCREWS
TOP
& BOTTOM
Top
& Bottom
33 Screws
SCREWS
LEFT
& RIGHT
Left
& Right
A
A
SECTION A-A
PROPRIETARY AND CONFIDENTIAL
Figure 25 Standalone Dimensions
DIM ARE IN INCHES
NAME
DATE
1/8
FRACTIONAL
DRAWN
CF
7/19/2016
.015
X.XX
9/18/2017
.005
X.XXX
CF
CHECKED
1
ANGULAR:
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
NOTE: This unit features two
drainage holes on each of the
sides of the unit. Be sure to
plan a drain system for both
in the wall and standalone
installations.
CANADIAN HEATING
PRODUCTS
27342 GLOUCESTER WAY,
LANGLEY, BC, V4W 4A1
SIZE
DWG. NO.
SCALE:
STAND ALONE 60SLDASM
1:20
SHEET:
REV.
3 OF 3
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
16"
16"
16"
16"
16"
76"
73"
14 3/4"
66"
26 15/16"
7"
42 1/2"
26 15/16"
7"
16"
26 15/16"
7"
16"
16"
42 1/2"
42 1/2"
PROPRIETARY AND CONFIDENTIAL
DIM ARE IN INCHES
NAME
DATE
CANADIAN HEATING
DIM ARE IN INCHES
PRODUCTS
NAME
DATE
CANADIAN HEATING
1/8
FRACTIONAL
27342 GLOUCESTER WAY,
PRODUCTS
DRAWN
CF
7/19/2016
LANGLEY, BC, V4W 4A1
1/8
FRACTIONAL
27342 GLOUCESTER WAY,
.015
X.XX CF
DRAWN
7/19/2016
LANGLEY, BC, V4W 4A1
.015
X.XX
9/18/2017
.005
X.XXX
CF
CHECKED
SIZE
REV.
DWG.
NO.
9/18/2017
.005
X.XXX
CF
CHECKED ANGULAR:
1
SIZE DWG.THIRD
REV.
NO. ANGLE PROJECTION
FRAME60
1
ANGULAR:
THIRD ANGLE
PROJECTION
UNLESS
OTHERWISE SPECIFIED
FRAME60
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
SCALE:
SHEET:
1:24
2
OF 3
ALL BENDS ARE 90
SCALE:
SHEET:
1:24
2 OF 3 DATE HEATING PRODUCTS IS PROHIBITED.
E INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR DIM
AS AARE
WHOLE
WITHOUT THE WRITTEN PERMISSION
IN INCHES
NAME OF CANADIAN
NG IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
1/8
FRACTIONAL
DRAWN
CF
7/19/2016
.015
X.XX
9/18/2017
.005
X.XXX
CF
CHECKED
SIZE DWG. NO.
1
ANGULAR:
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
SCALE:
SHEET:
1:24
Page 14
Figure 24 Standalone Dimensions
*12" minimum above grade is
required for US installations
*
CANADIAN HEATING
PRODUCTS
27342 GLOUCESTER WAY,
LANGLEY, BC, V4W 4A1
FRAME60
REV.
2 OF 3
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
Y:\Products\Residential Products\R&D Projects\P6016VONE\CAD Files\Manual Drawings\
STAND ALONE 60
16"
76"
Y:\Products\Residential Products\R&D Projects\P6016VONE\CAD Files\Manual Drawings\
STAND ALONE 60
66"
66"
Figure76"23 Back
14 3/4"
14 3/4"
Y:\Products\Residential Products\R&D Projects\P6016VONE\CAD Files\Manual Drawings\
STAND ALONE 60
Figure
22 Front
73"
"
SIZE
B
DWG.
SCALE:
INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANA
27342 GLOUCESTER WAY,
LANGLEY, BC, V4W 4A1
SIZE
DIM ARE IN INCHES
NAME
DATE
1/8
FRACTIONAL
DRAWN
CF
7/18/2016
.015
X.XX
9/18/2017
.005
X.XXX
CF
CHECKED
1
ANGULAR:
THIRD ANGLE PROJECTION
UNLESS OTHERWISE SPECIFIED
ALL BENDS ARE 90
Y:\Products\Residential Products\R&D Projects\P6016VONE\CAD Files\Manual Drawings\
STAND ALONE 60
DRAINAGE
HOLES
Wall
Installation HOLES
DRAINAGE
PROPRIETARY AND CONFIDENTIAL
14.750
PROPRIETARY AND CONFIDENTIAL
PROPRIETARY AND CONFIDENTIAL
66.000
Y:\Products\Residential Products\R&D Projects\P6016VONE\CAD Files\Manual Drawings\
P6016VFONE WALL INSTALLATION
14.750
Y:\Products\Residential Products\R&D Projects\P6016VONE\CAD Files\Manual Drawings\
P6016VFONE WALL INSTALLATION
65 1/2"
27.880
32.880
XG0219 - 170829
Installation
Clearances
Combustible mantels and mouldings may be safely installed over the top
and on the front of the fireplace provided that they do not project beyond
shaded area shown.
NOTE: National Canadian Gas Association mantel test requirements are
for fire hazard prevention to combustible materials.
Please be aware; temperatures over the mantel will rise above normal
room temperature and walls above fireplace may be hot to touch.
Mantels&Surrounds
Allowable Sidewall Clearances
Side wall clearances are 6" as shown.
17
16
15
Combustible construction
allowed in shaded area
14
Wall
board
Wall
Board
13
Combustible facing material
Vertical Height (In.)
12
11
10
9
opening
WindowWindow
Opening
8
7
6
5
4
6"
152
6"
152
45°
3
2
1
Combustible header
12 11 10 9
8
7
6
5
4
3
2
1
Horizontal Run (In.)
notAlowable
allowable
Not allowable
Not
Sidewall
Sidewall
Allowable
allowable
Area area
Figure 26 Sidewall Clearance
Combustible facing material
Figure 21.a Combustible mantles and facings. (Not to scale)
ClearanceSpecifications
• Full combustible construction allowed including combustible facing
material
• 6” minimum clearance to perpendicular wall
CAUTION
We recommend careful consideration be given to the effects of
elevated mantel temperatures which may be in excess of product
design, for example; candles, plastic or pictures. This can cause
melting, deformation, discolouration or premature failure of T.V. radio,
and other electronic components.
• Minimum clearance to ceiling (from fireplace opening): 36”
• Distance to combustible material in front: 36”
XG0219 - 170829
Page 15
Installation
Finishing
Wall
board/Finishing material
WALL
BOARD/FINISHING
MTL
PROPRIETARY AND CONFIDENTIAL
Fireplace
P42VFO
12"
MIN
Framing
FRAMING
*
Drainage
holes
DRAINAGE
HOLES
(both sides)
(BOTH
SIDES)
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
DATE
NAME
TMC 15-Aug-16
SIZE DWG. NO.
STAND ALONE
A
SCALE 1:18 WEIGHT:
REV.
SHEET 1 OF 3
\\pdm\shared$\Products\Residential Products\R&D Projects\PL42VO\Cad Drawings\MANUAL VIEWS\STAND ALONE\STAND ALONE
August-15-16 2:16:01 PM
Standalone
FireplaceFacing
When sizing the finish material
for your fireplace, it is important
to remember the following:
THE OPENING MUST NOT BE
OBSTRUCTED IN ANY WAY - to
do so restricts the air supply for
the control compartments and
heat exchanger it also prevents
access for servicing controls.
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
Figure 28 Standalone Finishing
In The Wall Installation
Fireplace
P42VFO
August-15-16 10:47:52 AM
Framing
FRAMING
12" MIN *
Finishing
material
FINISHING
MATERIAL
PROPRIETARY AND CONFIDENTIAL
Figure 27 In the wall finishing
DIMENSIONS ARE IN INCHES
TOLERANCES:
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
DATE
NAME
TMC 15-Aug-16
SIZE DWG. NO.
A
REV.
P42VFO WALL INSTALLATION
SCALE 1:17 WEIGHT:
SHEET 1 OF 3
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
\\pdm\shared$\Products\Residential Products\R&D Projects\PL42VO\Cad Drawings\MANUAL VIEWS\WALL\P42VFO WALL INSTALLATION
Wall
board
WALL
BOARD
FLOORING
Flooring
Page 16
Decorative facing must not
extend past the fireplace
opening, because it will interfere
with the access to retainers
for removal of glass door and
restrict airflow into the unit.
*12" minimum above grade is for
US installations only
XG0219 - 170829
Installation
ControlBoxInstall
MountingtheFireplaceControlBox
Wiring
Install the Fireplace Control Box in an accessible location within 3' of
the fireplace. The location should be where maintenance, adjustments
and service may be made easily.
A qualified electrician must install the wiring. The unit is supplied
with an external electrical control box pre-wired by the factory. The
control box is connected to the fireplace with a control cable that will
communicate with the fireplace. The control box should be located
where it can be accessed when the fireplace has been finished in.
Mount the control box with 4 #8 screws (not supplied) and seal with
an outdoor rated sealant.
USE #8
SCREWS FOR
MOUNTING
Use #8 screws for
mounting
Use #8 screws for
mounting
Installations in Canada must be electrically grounded in accordance
with CSA C22.1 Canadian Electrical Code Part 1 and/or Local Codes.
Installations in the USA must be electrically grounded in accordance
with local codes or, in the absence of local codes, with the National
Electrical Code, ANSI/NFPA 70.
Note: If any of the original wire supplied with the appliance is replaced,
it must be with the same it's equivalent.
Connect a 3-Conductor outdoor rated cable from the control box wire
marked "to blowers in fireplace" to the 3 wires on the right side of the
fireplace.
Figure 29 Control box mounting
CAUTION
Ensure the wires are properly isolated from metal parts or control
system will be damaged.
The control box must be mounted in the orientation shown above with
the wires descending from the bottom to minimize the potential for
water ingress.
Figure 30 Wires to Blowers
XG0219 - 170829
Page 17
Installation
WiringConnection
Control Box
24VDC
Red
Fast/Slow
SW
Black
Brown
110V
LED
PWR
SUPPLY
24V
Black
+ LED
CONTROLLER
White
+
R G B
Black
Red
Green
Blue
Red
Black
White
Stripe
Speed
control
On/Off
SW
Plug
Brown
White
Red
Remote
Black
Black
Green
White
Blue
Multiple
Connection
Options
Gas Valve
M
M
LED Lighting
Flue Gas Combustion
SW
SW
Fireplace
Red
Black
White
White
(3 IN PL60VO UNITS)
Red
Fireplace Blowers
Black
120VAC
3 foot
Power Cord
to control box
White
Red
Yellow
Tie together Red
and Black
for use
without a remote
Off
Remote
On
Red
PWR
to flue switch
Yellow
Gas Valve
Without Remote
With Optional Remote
Figure 34 Wiring schematic
Page 18
XG0219 - 170829
Installation
RemoteReceiverInstallation(OptionalAccessory)
WiringInstructions
A qualified electrician must install the remote control system.
Turn off all power and gas to fireplace.
NOTE: the control box is supplied with 3 feet of 3 conductor cable.
WARNING
This remote control system must be installed exactly as outlined
in these instructions. Read all instructions completely before
attempting installation. Follow instructions carefully during
installation. Any modifications of this remote control or any of its
components will void the warranty and may pose a fire hazard.
PART No.
1
2
3
4
DESCRIPTION
USE #8
SCREWS
FOR for
Use
#8 screws
1
HW2212
1"x2.75" MATED HOOK/LOOP
4 4VELCRO,
"
MOUNTING
mounting
EC1458
JUNCTION BOX 9100 NO TERM 125x167x82mm
RX5010- ON/OFF 110V RECEIVER FOR TOUCHSCREEN REMOTE
RECEIVER
EC1462
NYLON STRAIN RELIEF CONNECTOR, 1/2"
QTY.
Figure 37 Feeding the wire through the control box
3. Feed the wire into the control box side.
REV.
1
August-18-16 11:16:59 AM
ITEM No.
Loosenreliefconnectornutsbefore
feedingwirethrough
1
1
1
19
2 32 "
MOUNTING
MOUNTING
DIMENSIONS
DIMENSIONS
(Shown
w/o receiver)
(SHOWN w/o RECEIVER)
Figure 41 Mounting Dimensions
Figure 38 Connecting the wires
Figure 42 Receiver installed in box
PROPRIETARY AND CONFIDENTIAL
1. Attach the remote control box within 3 feet of main control box.
REMOTE CONTROL
(the remote receiver is attached with velcro and may have to P42
beELECTRICAL
BOX
removed to access mounting screw slots.
DIMENSIONS ARE IN INCHES
TOLERANCES:
NAME
DRAWN BY
FRACTIONAL 1/32"
.015"
TWO PLACE DECIMAL
CHECKED BY
THREE PLACE DECIMAL .005"
MATERIAL
ALL BENDS ARE ASSUMED
TO BE 90 UNLESS NOTED
FINISH
OTHERWISE.
Figure 39 Connecting the wires
4. Connect the wires shown above from the remote receiver to the wires
from the control box. Black to black, red to red, and white to white.
DATE
18/08/2016
SIZE DWG. NO.
A
SCALE 1:2
ECA102
WEIGHT:
REV.
SHEET 1 OF 3
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN HEATING PRODUCTS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF CANADIAN HEATING PRODUCTS IS PROHIBITED.
Figure 35 Receiver wires
Figure 36 Receiver wires
2. Locate the wire running from the remote receiver and remove the
wire nuts at the ends of the wires.
XG0219 - 170829
Figure 40 Securing the wire
5. After the wires are connected, tighten the strain relief connector
nuts.
Page 19
Installation
LEDRemoteReceiverInstallation(OptionalAccessory)
WiringInstructions
A qualified electrician must install the remote control system.
Turn off all power and gas to fireplace.
WARNING
This remote control system must be installed exactly as outlined
in these instructions. Read all instructions completely before
attempting installation. Follow instructions carefully during
installation. Any modifications of this remote control or any of its
components will void the warranty and may pose a fire hazard.
Figure 47 Connecting the LED receiver
3. Connect the white power connector from the LED receiver to the
connector from the control box.
Figure 43 Removal of wire nut
Figure 44 Removal of wire nut
1. The remote receiver is installed in the main control box. To start,
remove the wire nut from the wire feeding into the control box.
Figure 48 Wiring the LED receiver
4. Connect the wires from the remote receiver to their respective
terminals in the LED receiver (BK-Black R-Red G-Green BL-Blue)
Figure 45 Attaching the receiver
Figure 46 Attaching the receiver
2. Place a Velcro strip (provided) on the bottom of the control box to
fasten the receiver in place, with the other strip on the bottom of the
receiver. Then place the receiver into the box.
Page 20
XG0219 - 170829
Installation
LEDStripInstallation(OptionalAccessory)
LEDStripInstructions
Power to the unit MUST be disconnected before installing
For instructions on how to remove the door please see the door
install/removal section.
Figure 52 Loosening air baffle bolts
4. Loosen the 3 bolts securing the baffle to the back of the firebox.
Figure 49 Removing the media tray
1. Unscrew the 4 screws securing the media tray to the burner.
Figure 50 Removing the pilot cover
2. Remove the pilot cover from the burner tray.
Figure 51 Firebox with tray removed
3. The tray can now be removed from the firebox.
XG0219 - 170829
Figure 53 Adding LED air baffle
5. Place LED air baffle resting on the existing air baffle.
Figure 54 Installing LED air baffle
6. Install the LED strip baffle onto the bolts and tighten.
Figure 55 Connecting power
Figure 56 connected power
7. Connect the white power connector from the LED strip to the
connector in the right side of the firebox.
Page 21
Installation
Gasconnection
11 5/8"
294
FUELCONVERSION
GAS CONNECTION
• Verify that your fireplace is compatible with your available gas type.
(Natural Gas or Propane shown by "N" or "L" in your model number
and rating plate.
• The fireplace is supplied with a 1/2 FPT gas shutoff valve
• If gas type is not compatible, contact your local Montigo dealer as
this fireplace is NOT field convertible.
• Purge all air out of gas line.
• Connect incoming gas line to the 1/2" gas inlet pipe.
GASPRESSURE
• Check appliance connection, valve and valve train under normal
operating pressure with a commercially available leak check
solution.
• Optimum appliance performance requires proper input pressures.
• DO NOT USE A FLAME OF ANY KIND TO TEST FOR LEAKS.
13 1/2"
343
• Gas line sizing requirements will be determined in ANSI Z221.3
National Fuel Gas Code in the USA and CAN/CGA B149 in Canada.
3 1/4"
82
Pressurerequirementsare:
Gas Pressure
Natural Gas
Propane
Minimum inlet pressure
5.5in. w.c.
11in. w.c.
Manifold pressure
3.5in. w.c.
10in. w.c.
4 7/8"
124
• To check pressures, control valves have a provision to remove a
1/8” N.PT. plug to be fitted with a hose barb.
• Montigo requires a service shut off valve be located in an accessible
location to isolate the gas supply.
• Only install gas shut-off valves approved for use by the state,
province, or other governing body in which the fireplace is being
installed.
NOTE:
After gas line is connected, each appliance connection, valve
and valve train must be checked while under normal operating
pressure with either a liquid solution, or leak detection device,
to locate any source of leak. Tighten any areas where bubbling
appears or leak is detected until bubbling stops completely or
leak is no longer detected. DO NOT use a flame of any kind
to test for leaks.
PROPRIETARY AND CONFIDENTIAL
GAS
• The manifold outlet pressure is set from the factory to the
appropriate pressure but should be verified.
5 3/4"
146
NOTICE
Flexible gas connectors must not exceed 3 feet in length, unless
allowable within local regulations.
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF CANADIAN
WARNING
When pressure testing the fireplace, Gas line, and input system
follow the appropriate local codes or your area. DO NOT connect
the fireplace to pressures in excess of 1/2lb. This will damage the
gas control valve.
WARNING
When installing the fireplace - gas lines, fittings, accessories or
any other objects CANNOT impede the proper movement of the
fans or door.
Page 22
XG0219 - 170829
Installation
Installingthelouvres
Step 1:
Remove the protective coating from the louvers. Phillips-head stainless
steel screws are provided for installation.
Figure 57 Removing the left side screw
Step 2:
Position the top louver, as shown in this image, and attach using the
screws provided.
Figure 58 Removing the left side screw
Step 3:
Position the bottom louver and affix using the remaining screws.
Note: this louver must be uninstalled to remove the door
Figure 59 Removing the left side screw
XG0219 - 170829
Page 23
Installation
Installing&RemovingtheDoor
Removingthedoor
The doors are removed in a few simple steps. Follow these instructions
below.
Step 1:
Remove the Lower
louvre below the door
by removing screws as
shown.
Step 4:
Tilt the bottom of the door
upward to release the door
tab from the firebox slot.
Figure 62 Lifting the base of the door
Figure 64 Removing the left side screw
Step 2:
Step 5:
Remove the inner screw
on the lower left side below
the door. Placeonehand
underneathwhileunscrewing
thedoortocatchthescrew.
Figure 60 Removing the left side screw
Lift slightly and pull the
door forward to complete
the removal of the door.
Figure 63 Completing removal of the door
InstallingtheDoor
To install the door, simply follow the door removal instructions and reverse
order.
Step 3:
Remove the inner screw in
the same location on the
right side.
WARNING
When installing the fireplace - gas lines, fittings, accessories or
any other objects CANNOT impede the proper movement of the
door or other moving parts.
Figure 61 Removing the right side screw
Page 24
XG0219 - 170829
Installation
InstallingtheFirestones
The unit is supplied with firestones, 6lbs for PL42VO, 9lbs for the PL60VO
(order code HW1106). Remove the door as shown in the previous
Instruction. Follow these instructions to ensure all parts are removed or
replaced as required. Once the glass door is removed place the firestones
randomly across the pan and the burners as described.
Note: Only cover the burner with one layer of media
WARNING
Firestones or another approved media must be installed before
operating the fireplace.
Figure 67 DO NOT place ANY firestones on top of the pilot
cover).
WARNING: This appliance is intended for use only with the included
Montigo burners and accessories. Never install or add any additional or
alternative media, rock wool or other material in this appliance. The use
of additional or alternative materials may pose potential safety hazards,
damage to the appliance, and void manufacturer’s warranty.
Figure 65 Installation of the firestones. (Ensure ONLY one
layer of firestones cover the burner surface).
Figure 66 Spreading the firestones evenly and make sure
there are no firestones covering the pilot.
XG0219 - 170829
Page 25
Installation
InstallingOptionalMedia
InstallingOptionalSpeckledStones
InstallingOptionalDriftwoodLogSet(PL42VO)
[RR150SS for PL42VO, RR300SS for PL60VO]
[LGS59]
Once the glass door has been removed, place the speckled stones evenly
across the pan and burner see figure 55. Ensure stones do not overlap too
much as this will effect the flame pattern, see Figure 55. DO NOT cover
the pilot with stones, see Figure 56. Ensure numbers are facing down.
The PL42VO has the option of installing a driftwood log set. Once the
firestones or speckled stones have been installed the log set can be
installed.
Ensure logs are securely placed and will not tip or fall. Remove media
where logs touch the burner tray to ensure a more secure position.
Driftwood logset MUST be installed with Firestone, Fireglass or Speckled
Stone media as a base.
Figure 68 Evenly placed speckled stones
1
2
3
4
5
6
Figure 70 LGS59
Step 1. Place Log 2 in the front left corner of the burner tray. Ensure log
does not cover pilot. See Figure 58.
2
Figure 69 Ensure the stones DO NOT cover the pilot.
WARNING: This appliance is intended for use only with the included
Montigo burners and accessories.
Never install or add any additional or alternative media, rock wool or other
material in this appliance.
The use of additional or alternative materials may pose potential safety
hazards, damage to the appliance, and void manufacturer’s warranty.
Figure 71
Step 2. Place Log 5 to the right of log 2 at the back of the media tray.
Figure 59.
2
5
Figure 72
Page 26
XG0219 - 170829
Installation
InstallingOptionalMedia
Step 5. Place Log 4 at the rear of the firebox, parallel to the media tray.See
Figure 62.
Step 3. Place Log 3 resting diagonally against log 5, with the thinner end
pointing into the top left corner of the firebox. See Figure 60.
3
6
5
2
4
Figure 75
Figure 73
Step 4. Log 6 is placed in the center of the media tray with the curved end
pointing out of the fireplace. See Figure 61.
3
Step 6. Log 1 is placed at the right end of the media tray, parallel to the
right side wall of the firebox. See Figure 63.
6
6
4
Figure 74
5
2
1
Figure 76
3
4
6
1
Figure 77 Completed Installation
XG0219 - 170829
Page 27
Installation
InstallingOptionalMedia
InstallingOptionalDriftwoodLogSet(PL60VO)
[LGS59 x2]
Step 3. Place Log 1 resting diagonally against the front of the media tray.
See Figure 76.d
The PL60VO has the option of installing a driftwood log set. Once the
firestones or speckled stones have been installed the log set can be
installed.
1
Ensure logs are securely placed and will not tip or fall. Remove media
where logs touch the burner tray to ensure a more secure position.
Driftwood logset MUST be installed with Firestone, Fireglass or Speckled
Stone media as a base.
Figure 76.d
Step 4. Log 1 is placed in the back center of the media tray. See Figure
76.e
1
2
1
3
4
5
6
Figure 76.a LGS59x2
Step 1. Place Log 6 in the left back corner of the burner tray. Ensure log
does not cover pilot. See Figure 76.b
6
Figure 76.e
Step 5. Place Log 2 resting diagonally against log 1, with the thinner end
pointing into the top right corner of the firebox. See Figure 76.f
2
2
Figure 76.f
Figure 76.b
Step 2. Place Log 5 to the right of log 6 at the back of the media tray.
Figure 76.c
Step 6. Log 4 is placed in the back of the media tray between logs 2 and
5. See Figure 76.g
4
2
55
Figure 76.c
Page 28
Figure 76.g
XG0219 - 170829
Installation
Step 7. Place Log 3 resting diagonally against log 4, with the thinner end
pointing into the back of the firebox. See Figure 76 .h
Step 11. Place Log 4 resting diagonally against the top right corner of the
firebox. See Figure 76 .l
4
3
Figure 76 .h
Figure 76 .l
Step 8. Log 2 is placed in the center-front of the media tray in front of log
2. See Figure 76 .i
Step 12. Log 6 is rested diagonally on log 4. See Figure 76 .m
2
Figure 76 .i
6
Figure 76 .m
Step 9. Place Log 5 parellel to the right of log 1 . See Figure 76 .j
5
Figure 76 .j
Step 10. Log 3 is placed in front of log 5, resting agaist the front of the
media tray. See Figure 76 .k
3
Figure 76 .k
XG0219 - 170829
Page 29
Operation
Startupandinitialoperation
LEDOperationVerification–
Applicableiflightkit(MCLEDVO)isinstalled
InitialFireplaceOperationVerification–
Ifgassupplynotyetconnected
• Install 2 AAA batteries into LED remote
• Check that the door glass is clean. Clean if required.
• Turn on main power to fireplace control box
• Check that the visible surfaces inside the fireplace and on the door
frame are free of smudges. Clean if required prior to initial lighting.
• Fireplace ON/OFF switch does not need to be turned on to operate
LED lights.
• Using the LED remote, turn lights OFF then ON
• Using the LED remote, switch between blue, red and green. When
each color is selected, verify all LEDs display the same color.
• Turn off the LEDs
• Ensure the fan speed control toggle switch is set to the SLOW position
• Turn the fireplace on using the control box ON/OFF switch. If the fireplace
remote option is installed, also turn on using the fireplace remote.
• The fans will turn on and the hot surface igniter start to glow. If the
igniter doesn’t glow within 1 min, refer to Troubleshooting.
OptimizingtheFanSpeed
Adjust the fan to optimal operational speed by performing the
following steps. This will ensure the quietest operation possible at
slow speed.
Figure 79 Remote Front
Figure 80 Remote Back
InitialFireplaceOperationVerification–
Ifgassupplyisconnected
• Check that the door glass is clean. Clean if required.
• Check that the visible surfaces inside the fireplace and on the door
frame are free of smudges. Clean if required prior to initial lighting.
• Ensure the fan speed control toggle switch is set to the SLOW
position
Step1:
Ensure the fan speed control toggle switch is set to the
SLOW position
Step2:
Decrease the fan speed to the minimum speed using the
dial in the control box
Step3:
Turn the fireplace ON/OFF switch to the ON position. If the
fireplace remote option is installed, also turn on using the
fireplace remote.
Step4:
Slowly increase the fan speed in small increments until the
hot surface igniter starts to glow.
Note: It is very important that if while adjusting the fan speed you
would like to decrease it, you must begin again at step 2 to ensure
correct fan speed set-up.
Increase
speed
• Refer to lighting instructions for information on how to light the
appliance.
• Turn the fireplace on using the control box ON/OFF switch. If the
fireplace remote option is installed, also turn on using the fireplace
remote. The following sequence of events should take place:
• The igniter will attempt to light the pilot. The Igniter will glow for
30 seconds, pause for 30 seconds. This cycle will occur twice
before the system enters a lockout mode. After 5 minutes the
system will attempt to light again.
• The pilot will light.
Decrease
speed
Figure 78 Setting fan speed
• The igniter will stop glowing.
• The Burner will light
• If driftwood logs have been installed, check the logs for carboning
and reposition if necessary.
• Refer to Troubleshooting if you encounter any issue during the
ignition sequence.
Page 30
NOTICE
Fan speed optimization must be performed only when fireplace is cold
XG0219 - 170829
Operation
OperatingtheFireplace
The unit is controlled using the ON/OFF switch at the side of the
control box or by using the optional remote control (RXM5010VO).
When placed in the ON position the fans will initialize, the igniter will
start to glow and the pilot will light, followed by the main burner.
OperatingtheAccentLights
The accent lighting is operated by the LED remote control. See LED
Remote Control Operation section for detailed instructions.
When placed in the OFF position the flame and fans will turn off.
If the fireplace does not light after two attempts it will go into a safety
lock-out mode. After five minutes the fireplace will attempt to light
again. If the fireplace will not light, turn the fireplace off, turn off all the
electrical power to the appliance, locate the gas shut off valve and turn
the gas off. Call your service technician or local Montigo dealer. Never
attempttolightthepilotbyhand.
Thisfireplaceincludesascreenbarrierwhichhelpspreventinjuryfrom
burns.Neveroperatethisappliancewithoutthescreenattached.Children
andotheratriskindividualsshouldbemonitoredatalltimes.
ON
Off
Color ring
Indicating light
Model: 5010
Speed+
Brightness+
Mode+
INSTALLATION AND OPERATING INSTRUCTIONS
OperationSuggestions
Brightness-
Mode-
Speed-
YOU
CANNOT
READwhile
OR UNDERSTAND THESE INSTALLATION
• If on a windy day the fireplaceIF
flame
goes
out unexpectedly
the fan is set at high speed, toggle switch to slow speed. The flameATTEMPT TO INSTALL OR OPERATE
should relight.
INSTRUCTIONS DO NOT
INTRODUCTION
• If on a calm day you prefer warmth spread farther from the fireplace,
switch may be set to high speed.
This SKYTECH remote control system was developed to provide a safe, reliable, and user-friendly remote control system
system operates on radio frequenci
security codes that are programme
transmitter at the factory; the remote receiver’s code must be matched to that of the transmitter prior to initial use.
• If on a cold morning the fireplace doesn’t light on slow speed,
heating
appliances.
The
system
can then
be operated
from the transmitter. The
switch
to high
speed until the
fireplace
is warm,
switch backmanually
to
a 20-foot
low
speed. range using non-directional signals. The system operates one of 1,048,576
CAUTION
The transmitter operates on 4 AAA-size 1.5V batteries. It is recommended t
Follow
all warnings
and instructions
when
using thelife
appliance
ALKALINE batteries
always
be used
for longer
battery
and maximum op
performance. IMPORTANT: New or fully charged batteries are essential fo
operation of the multi-function transmitter. Insert 4 AAA-size 1.5 V batteries
battery compartment on the back of the transmitter, positioning the (+) and (
batteries as indicated on the casing. When the batteries are inserted, the sc
(with similar numbers) will display.
ON
OFF
BATTERY
COMPARTMENT
BATTERY
Note: On initial start up if a LOW battery icon appears on
the screen, check the position of the batteries.
COMPARTMENT
FRONT
XG0219 - 170829
1
BACK
O
O
Page 31
5
6
8
Note: Due to the sensitive temperature-monitoring
components in the transmitter, it may be necessary to
allow the transmitter to stabilize to room temperature
before accurate room temperatures are displayed on
the screen. If the transmitter is activated from a
severe cold condition, it can take up to fifteen minutes
for accurate temperature readings to appear.
Operation
FOR YOUR SAFETY
- READ BEFORE
LIGHTING:
WARNING If the information in these instructions are not followed
exactly, a fire or explosion may result causing property damage,
personal injury or death.
WARNING / CAUTION: Hot while in operation. Do not touch.
Severe burns may result. Keep children, clothing, furniture,
gasoline and other liquids having flammable vapors away.
See installation and operating instructions accompanying this appliance.
A. This appliance has a pilot which is lit automatically. Do
not attempt to light the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area
for gas. Be sure to smell next to the floor because some
gas is heavier than air and will settle on the floor.
What To Do If You Smell Gas:
■ Do not try to light the appliance.
■ Do not touch any electrical switch. Do not use any
phone in your building.
■ Immediately call your gas supplier from a
neighbour's phone. Follow the gas suppliers
instructions.
■
If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control
knob. Never use tools. If the knob will not push in or turn
by hand, don't try to repair it. Call a qualified service
technician. Force or attempt to repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system, and any gas control which has been
under water.
LIGHTING INSTRUCTIONS:
1.
STOP! Read the safety information above on this label.
2.
Turn the fireplace "OFF" using the wall switch or remote
control.
3.
Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on
this label. If you don't smell gas, go to the next step.
4.
Turn the fireplace "ON" using the wall switch or remote
control.
NOTE: This unit is equipped with an ignition system
that lights the pilot burner automatically. Do not
attempt to light the pilot by hand.
5.
Once the predetermined airflow is established in the
firebox. The hot surface igniter will start to glow. The pilot
will light up, followed by the main burner. The fireplace
will then start up.
NOTE: If the igniter does not glow, even after 3 minutes
have passed, follow the instructions "To Turn Off
Gas To Appliance" and call your service
technician or Montigo dealer.
TO TURN OFF GAS TO APPLIANCE:
Page 32
1.
Turn the fireplace off using the wall switch or remote
control.
2.
Turn off all electrical power to the appliance.
3.
Locate the gas shut off valve for the appliance and
turn off.
P/N LB1214-081216
This unit is equipped with advanced safety
controls. The fireplace will not turn on until all
of the safety conditions are met.
XG0219 - 170829
0
M
0
SETTING F / C SCALE
INSTALLATION AN
ON
IF YOU CANNOT READ OR UNDE
ATTEM
The factory
setting
Operation
hold the ON butto
for (5) seconds. F
INTRODUCTION
OFF
Remote(RXM5010VO)
This SKYTECH remote control system was developed to p
heating appliances. The system can be operated manuall
a 20-foot range using non-directional signals. The system
transmitter at the factory; the remote receiver’s code must
The remote operates on 4-AAA batteries that are included with this
kit. Install the AAA Batteries supplied with the unit into the battery
compartment. It is recommended to use ALKALINE batteries with this
product. Be sure the batteries are installed with the (+) and (-) ends
facing in the correct direction.
CHILDPROOF “LOCK-OUT”
The transmit
ALKALINEfea
b
This remote control includes a CHILDPROOF “LOCK-OUT”
“LOCK-OUT” operation of the appliance from theperformance
TRANSMITTE
operation of
SETTING “LOCK-OUT”
battery comp
batteries as
ON
(with similar
When the batteries are installed, the temperature indicator should
have a value and the ON and OFF buttons should appear on the
screen. If they do not appear, check the orientation of the batteries
and change if necessary.
1.
OFF
Note: Due to the sensitive temperature-monitoring components in the
transmitter, it may be necessary to allow the remote to stabilize to
room temperature before accurate room temperatures are displayed
on the screen. If the remote is activated from a severe cold condition,
it can take up to fifteen minutes for accurate temperature readings to
appear.
ON
2.
BATTERY
BATTERY
COMPARTMENT
COMPARTMENT
Note: Due t
components
allow the tran
NOTE:
If the
app
before
accur
will not cancel the
the screen.
operation of the T
severe cold c
for accurate
OFF
Receiver
FRONT
When plugged into a standard 110-120 VAC receptacle, the remote
receiver operates on commands from the transmitter or from the slide
switch on the face of the receiver.
Figure 81 Remote
1
8
6
RECEIVER
ON
REMOTE RECEIVER
REMOTE
RECEIVER
2
ANTENNA
ANTENNA
• OFF: will disable the remote receiver.
7
VALVE
VALVE
• It is suggested that the slide switch be placed in the OFF position if
you will be away from your home for an extended period of time.
Installation
LEARN
LEARN
OFF
4
3
• The remote receiver can be placed close to the electrical control
box.
DryCONTACT
Contact
DRY
spade
(2)
SPADE
(2)1/4"
1/4”
female
CONNECTORS
Connectors
OFF
REMOTE
REMOTE
ON
ON
TO 120VAC
120VAC INPUT
To
input
SLIDE
Slide
SWITCH
Switch
Protection from extreme heat is very important. The remote receiver
should be kept away from temperatures exceeding 130ºF. Extreme
heat can cause damage, which is not covered under warranty.
• Before installation, make sure you turn the slide switch to OFF. After
installation, make sure you turn the slide switch to REMOTE.
BACK
5
• ON: will manually turn on the fireplace.
• REMOTE: will allow use of handheld transmitter. If the system does
not respond to the transmitter on initial use, check the battery
positions in the remote. If that does not work, see the SECURITY
CODE section.
To activate the “LO
screen
together,
Note:
On inf
To the
disengage
the
screen,
together, for 5 sec
will return to its no
1.
2.
3.
4.
5.
6.
7.
8.
When plu
operates
of theBA
rec
appliance
ON
relayOFF
in it
current
p
FLA
output si
RO
F
LOC
This RF
501
0
to contro
OPERATION FUNCTIONS
Figure 82 Remote Receiver
1.
Touch anyplace on th
_________________________________________________
ON
Skytech 5010
OFF
XG0219 - 170829
2.
3.
seconds.
Touch the ON button
Touch the OFF button
Page 33
_____________________________________________
Operation
Remote(RXM5010VO)
GeneralInformation
The system can be operated manually from the receiver using the slider
switch.
• Please read all instructions carefully
• We strongly recommend that all electrical service work be performed
by a qualified electrical contractor.
• Check to ensure that all components required for installation are
included in your package.
LearningRemotetoReceiver
This transmitter has one of 65,536 unique security codes. It may be
necessary to program the remote receiver to “learn” the security code
of the transmitter upon initial use, if batteries are replaced, or if using a
replacement transmitter.
NOTE: This receiver can hold up to 3 transmitter codes. This is for the
times when a second hand held transmitter or a wall transmitter is
required.
• Make sure the receiver’s slide switch is in the REMOTE position.
• Press and release the LEARN button on the receiver.
SystemCheck
• Slide the 3-position button on the remote receiver to the ON position.
The fireplace will go through the start cycle and the hot surface igniter
will glow after the pre purge time and ignite the pilot. NOTE: If the
remote does not communicate with the receiver, go to the section:
Learning Transmitter to Receiver.
• After the pilot flame is lit, the main gas valve should open and the
main gas flame should ignite.
• Slide the button to OFF. The main gas flame and pilot flame should
both extinguish.
The power vent will turn off after 3 minutes post purge.
• Slide the button to REMOTE, then press the ON button on the
transmitter to change the system to on.
RemoteWallClip
The remote can be mounted on a wall using the remote wall clip included.
• Wood - Drill 1/8’’ pilot holes and install with screws provided.
• Plaster/Wallboard - Drill 1/4’’ holes, then install with the screws
provided.
• When you hear the “Beep”, press and hold the ON or OFF button for
about 2 seconds on the transmitter.
• You will then hear a series of rapid beeps that indicate that your new
transmitter has been accepted by the receiver.
• If you press the LEARN button on the receiver and you hear no
beeps, the receiver is unable to retain any more transmitter codes
(make sure the transmitter battery is properly installed and fully
charged).
• To delete all of the transmitter codes on your receiver, press and
hold the LEARN button for 10 seconds. Then you will hear a series
of three long beeps, indicating that the receiver’s memory has been
cleared.
Figure 83 Remote Wall Clip
Page 34
XG0219 - 170829
1
INTRODUCTION
ATTEMPT TO INSTALL OR
6 OPERATE
8
ON
2
OFF
3
This SKYTECH remote control system was developed to provide a safe,
reliable, and user-frie
Operation
heating appliances. The system can be operated manually from the transmitter.7 The system
a 20-foot range using non-directional signals. The system operates one of 1,048,576 security
transmitter at the factory; the remote receiver’s code must be matched to that of the transmitte
Remote(RXM5010VO)
RemoteLayout:
1. Battery Icon - Battery power is low. Replace batteries within two
weeks.
2. ON - Indicates the appliance is ON - Flame Icon
3. OFF - Indicates the ON
appliance is OFF - NO Flame Icon.
4. Flame - Indicates burner/valve is in operation.
The transmitter operates on 4 AAA-size 1.5V bat
ALKALINE batteries always be used for longer b
4
Howtooperate:
performance.
IMPORTANT: New or fully charge
Touch
anywhere on of
the screen
and the screen's blue back
light will light
operation
the multi-function
transmitter.
Insert
and stay lit for five seconds. Touch the ON button on the LCD screen to
battery
compartment
on the
of the
turn
the appliance
ON. Touch the OFF button
on theback
LCD screen
to turntransmitt
thebatteries
appliance OFF.as indicated on the casing. When the b
(with similar numbers) will display.
OPERATION FUNCTIONS
5. ROOM - Indicates current room temperature
OFF
6. °F indicates degrees Fahrenheit (°C indicates degrees Celsius).
BATTERY
COMPARTMENT
7. LOCK - Child lock out
8. RF SIGNAL - Appears when RF signal is being transmitted.
Note: On initial start up if a LOW battery icon ap
the screen, check the position of the batteries.
Note: Due to the sensitive temperature-monitori
components in the transmitter, it may
1.be necessa
Touch
ON
allow the transmitter to stabilize to room tempera
secon
before accurate room temperatures 2.
are displaye
Touch
OFF
the screen. If the transmitter
is activated
from
a
3.
Touch
severe cold condition, it can take up to fifteen min
for accurate temperature readings to appear.
ON
OFF
FRONT
BACK
5
1
6
_________________________________
8
ON
ON
Figure 85 How to operate
Skytech
5010
2
1.
2.
3.
4.
5.
6.
7.
8.
7
OFF
OFF
3
4
BATTERY ICON - Battery power is low
ON- Indicates the appliance is ON – Fla
OFF- Indicates the appliance is OFF – N
FLAME – Indicates burner/valve in ope
ROOM – Indicates CURRENT room tem
0
F indicates degrees Fahrenheit (ºC ind
LOCK – Child lock out.
RF SIGNAL ICON –Appears when the
Figure 84 Remote Layout
OPERATION FUNCTIONS
XG0219 - 170829
Page 35
ON
1.
Touch anyplace on the screen and the screens blue back
seconds.
0
0
SETTING F / C SCALE
Operation
ON
Remote(RXM5010VO)
T
h
f
OFF
ChangingtheTemperatureScale:
ChangingtheChildproofLock:
The factory temperature setting is Fahrenheit.
The remote control includes a childproof lock-out feature.
To change the setting to Celsius, simultaneously press and hold the ON
button and FLAME ICON on the LCD screen for five seconds.
To activate the childproof lock, simultaneously press and hold the ON and
OFF icons on the LCD screen for five seconds. The lock icon will appear
on the LCD screen.
Repeat the procedure above to change back to Fahrenheit.
0
Repeat the procedure above to disenge the childproof lock. The lock icon
will disappear and the system will return to normal operation.
0
CHILDPROOF “LOCK-OUT”
SETTING F / C SCALE
Note: the childproof lock prevents the transmission of the RF signal from
the remote. Engaging the childproof lock while the appliance is operating
This remote control includes a CHILDPROOF
will not turn the burner off.
“LOCK-OUT” operation of the appliance from t
SETTING “LOCK-OUT”
ON
ON
0
The factory setting for temperature is F. To change
hold the ON button and the FLAME ICON on the tran
1. to chanT
for (5) seconds. Follow this same procedure
s
ON
ON
2.
T
t
w
OFF
OFF
OFF
OFF
N
w
o
This remote control includes a CHILDPROOF “LOCK-OUT” feature that allows the user to
“LOCK-OUT” operation of the appliance from the TRANSMITTER when it is in the “LOCK OUT” m
CHILDPROOF
Figure 86 Changing “LOCK-OUT”
the Temperature Scale
SETTING “LOCK-OUT”
Figure 87 Changing the Childproof Lock
1.
ON
2.
RECEIVER
To activate the “LOCK-OUT” feature, press and hold
screen together, for 5REMOTE
seconds.
The lock icon will ap
RECEIVER
To disengage
the “LOCK-OUT”, press and hold the O
ANTENNA
together, for 5 seconds. The lock icon will disappear
will return to its normal operating condition.
VALVE
Page 36
OFF
LEARN
Dry Contact
(2) 1/4” female
Connectors
XG0219 - 170829
NOTE: If the appliance is already operating in the O
will not cancel the operating
MODE. Engaging the “L
OFF
REMOTE
ON
operation of the TRANSMITTER
Operation
Remote(RXM5010VO)
BatteryLife
Troubleshooting
Life expectancy is based on usage.
• Annually.
If you encounter problems with your fireplace system, the problem may be
with the fireplace itself or it could be with the remote control. Review the
fireplace manual to make sure all connections are properly made. Then
check the operation of this remote in the following manner:
• When operating range becomes reduced.
1.
Be sure the transmitter's batteries are properly installed and that the
battery output is 5.0 V or more.
2.
Ensure the receiver is connected to a 110-120 VAC power source.
3.
Check to make sure the transmitter is communicating with the
receiver
Check and replace all batteries:
• When transmissions are not received by the remote receiver.
• If the hand held transmitter batteries measure less than 5.0
volts.
• If the receiver beeps when the MODE button is depressed on
the transmitter they are communicating.
WARNING
• If the receiver does not beep when the MODE/SET button is
depressed on the transmitter, you will need to teach the receiver
the code of the transmitter. This is done by pressing and
releasing the LEARN button on the receiver and depressing the
MODE/SET button on the transmitter. A change in the beeping
pattern at the receiver indicates the transmitter's code has been
programmed into the receiver.
BatteryOperatedDevice
Read the battery instructions before installing them into the system.
Do not expose any battery, or its holder, or a device in which
batteries are involved, to a working temperature of the device to
which the batteries are connected is reported to be greater than
54C / 129F. In bad cases, overheating can cause hydrogen gas
and danger of explosion.
NOTICE
4.
Make sure the transmitter is within 15 to 20 feet of the receiver.
5.
Positioning of the receiver is important. If the receiver is enclosed in
a metal surround the operation of the receiver may be affected as
noted below. Reposition the receiver to improve operating range. It is
suggested that a heat shield be installed to protect the receiver from
extreme heat. If the receiver is enclosed in a metal surround this can:
• Cause the RF signal to get lost and interrupt communication
with the receiver.
• Cause the working distance to be shorter than normal.
Please note leaving batteries installed in the remote for an
extended period when not in use may cause the batteries to drain
and/or corrode.
Note: A receiver located in an area where ambient temperature inside the
case exceeds 130°F will trigger the THERMO-SAFETY feature requiring
repositioning of the receiver to stop the warning beeps and reset the
receiver's operation.
FCCREQUIREMENTS
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE
FOR ANY RADIO OR TV INTERFERENCE CAUSED
BY UNAUTHORIZED MODIFICATIONS TO THE
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE
USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
XG0219 - 170829
Page 37
Operation
LEDRemoteControlOperation(MCLEDVO-01)
This system is a high-performance RGB LED touch remote controller,
adopting the most advanced PWM control technology, controlling
all RGB LED products with five lines and three circuits( common
anode),allowing 640 thousand colors and 12 automatic changing modes
to choose from.
Also, It has a memory function(that is to say, the previous settings will
be resumed when power is on again). It is widely used in LED RGB strip
light, LED modules and so on. With the technology of the 2.4G high
frequency wireless remote control, it has the characteristics of low power
consumption, long distance transmission, and strong anti-interference
ability ,high speed telecommunications, etc.
ON
Off
Indicating light
Color ring
Speed+
Mode+
Brightness+
Brightness-
Mode-
Speed-
Mode
Brightness
state
Speed
state
1
Static white color
Adjustable
Unadjustable
2
White color gradual changes
Adjustable
Adjustable
3
All colors gradual change
Adjustable
Adjustable
4
Red/green/ blue three colors
gradual change
Adjustable
Adjustable
5
Seven colors jump to change
Adjustable
Adjustable
6
Three colors jump to change
Adjustable
Adjustable
7
Red/ green jumps to change
Adjustable
Adjustable
8
Red/blue jumps to change
Adjustable
Adjustable
9
Blue/green jumps to change
Adjustable
Adjustable
10
White color frequently blinks
Adjustable
Adjustable
11
White color glitters
Adjustable
Adjustable
12
Red color frequently blinks
Adjustable
Adjustable
13
Red color glitters
Adjustable
Adjustable
14
Green color frequently blinks
Adjustable
Adjustable
15
Green color glitters
Adjustable
Adjustable
16
Blue color frequently blinks
Adjustable
Adjustable
17
Blue color glitters
Adjustable
Adjustable
18
Yellow color frequently blinks
Adjustable
Adjustable
19
Yellow color glitters
Adjustable
Adjustable
#
20
Figure 88 Remote functions
Item
Circulation mode
Figure 90 Remote modes
Parameters
Programming(CodeClearingandCodeMatching)
Working Voltage
AAA*2pcs(3V)
Radio Frequency
2400-2483.5MHz
CodeMatching:Confirm it is correctly connected between power supply,
LED controller and LED load.
Modulate Method
GFSK
Transmit Power
6db
Standby Power Consumption
10uA
Remote Distance
20-30m
Dimension
110×52×30mm
Figure 89 Remote parameters
Page 38
Switch off the power, then switch on again, and press S+ button once
(within 3 seconds) the moment you see the light on the power supply.
The LED light blinks twice slowly when it is done.
CodeClearing:Confirm it is correctly connected between power supply,
LED controller and LED load.
Switch off the power, then switch on again, and long press S+ button
(within 3 seconds) the moment you see the light on the power supply.
The LED light quickly blinks nine times when it is done.
XG0219 - 170829
Operation
LEDRemoteControlOperation(MCLEDVO-02)
Mode
Brightness
state
Speed
state
1
RGB Change
Adjustable
Adjustable
2
Color Change
Adjustable
Adjustable
3
White Flash
Adjustable
Adjustable
4
RGB Fade
Adjustable
Adjustable
5
Color Fade
Adjustable
Adjustable
6
RG Fade
Adjustable
Adjustable
7
RB Fade
Adjustable
Adjustable
8
GB Fade
Adjustable
Adjustable
9
White Fade
Adjustable
Adjustable
10
All Mode Cycle
Adjustable
Adjustable
#
Color Circle
Pause
On/Off
Brightness +/-
Mode +/Speed +/-
Figure 93 Remote modes
Figure 91 Remote functions
Item
Parameters
Input voltage
DC12V-24V
Output
max 3A x 3CH
Power
max 108W (12V)/216W (24V)
Working Temp
-30°C to 55°C
Dimensions
L135xW30xH20 (mm)
Weight (N.W.):
248g
Remote Working Voltage/
Frequency
3V / 433.92MHz
Remote Working Distance/Temp
40-50m / -20°C to 55°C
Remote Dimensions/Weight
L106xW156xH9 (mm) / 40g
Programming(CodeMatching)
LearningIDMethod:The remote and receiver have been paired in the
factory. If deleted, you can pair the two as follows. To LEARN, Press
red ID learning button on the receiver until the running light is on. Now
press any key on the remote. To CLEAR, press ID learning button on the
receiver for 5s.
Figure 92 Remote parameters
XG0219 - 170829
Page 39
Maintenance
Installing&RemovingtheScreen(Forcleaningoutsideofglass)
Note: Do not operate fireplace without screen in place.
Step 1:
Step 3:
Remove the door/screen
from the firebox ( see door
removal instructions on
previous page )
Pull the screen upwards to
remove it from the door.
Figure 94
Figure 96
ReplacementScreens:
For replacement part order numbers, please refer to section
"Replacement Parts:"
Step 2:
Remove the screws, from
the top and bottom.
Figure 95
Page 40
XG0219 - 170829
Maintenance
Troubleshootingguide
Problem
PossibleCauses
Solution
No power to the control box or the power
from the control box is not connected to
the fireplace.
When the wall switch on the
control box is in the on position
the fans are not running.
Fan Dial could be turned down.
Test the power outlet for a full 110 Volts of power. Make sure
that the power from the control box is connected to the PPO
box of the fireplace.
The fans are running but the
glow plug is not glowing red.
Fans are running too slow or air intake
under the door is restricted.
Turn the fan speed to a higher speed that will power up the
smart valve.
The glow plug is glowing but the
pilot is not burning.
No gas to the fireplace, or air blocking the
gas from reaching the burner.
Check the gas valve and make sure it is in the on position
make sure that the air has been bled out of the gas supply
line.
Remove the power supply plug and test for voltage when
fans are running at full speed.
Fans are running at maximum
speed and glow plug is not
glowing.
If you measured 24 or more volts on the plug, replace gas
valve.
No power to the valve
Water may have penetrated the gas valve.
Losing the main burner flame on
a windy day
The wind is too strong to overcome the
blowers from the fireplace
If the unit does not light at maximum fan speed in high-wind
conditions, toggle the fan speed to low
Figure 97
If your fireplace still does not operate correctly, consult your local Montigo dealer.
All service and repairs must be performed by a qualified Technician.
All spare parts, optional fans, media, and optional trim finishes are available from your local Montigo dealer.
Visit www.montigo.com to locate your nearest dealer.
XG0219 - 170829
Page 41
Maintenance
Maintenance/CleaningInstructions
WARNING! Media may have sharp edges, wear safety glasses
and gloves when handling. Do not change or substitute the media
material provided with this appliance. If replacing, use only approved
replacement media available from your local montigo authorized
dealer/distributor.
WARNING! To avoid the possibility of burns, maintenance should be
done only when the appliance is cool. Avoid unprotected contact with
hot surfaces. Ensure burner is turned off. Turn gas off at source and
disconnect the power to the appliance before servicing.
MAINTENANCE/CLEANINGINSTRUCTIONS
WARNING! Hose: Check for abrasions, melting, cuts, and cracks in
the hose. If any of these conditions exist, do not use the appliance.
Have the part replaced by your Montigo dealer or qualified gas
installer.
WARNING! If the gas control is exposed to water in any way, DO NOT
try to use the appliance. The gas control must be replaced.
Note:Stainless steel tends to oxidize or stain in the presence of
chlorides and sulfides, particularly in coastal areas and other harsh
environments, such as the warm, highly humid atmosphere around
pools and hot tubs. These stains could be perceived as rust, but
can be easily removed or prevented. To provide stain prevention and
removal, wash all stainless steel surfaces every 3-4 weeks or as often
as required with fresh water and/or stainless steel cleaner.
Page 42
XG0219 - 170829
Appendix
AppendixA:Warranty
TheWarranty
LimitationsOnLiability
The Companies warrants the Montigo Gas Appliance to be free from
defects in materials and workmanship at the time of manufacture. On
the Montigo fireplace, there is a ten-year warranty on the firebox and
its components, a five-year warranty on the main burner and pilot
burner, and a one-year warranty on the gas control valve, fibre logs
and all electrical components. The Glass, plated / painted finishes,
and refractory lining are exempt from the warranty.
It is expressly agreed and understood that The Companies sole
obligation, and purchaser's exclusive remedy under this Warranty,
under any other warranty, expressed or implied, or in contract, tort
or otherwise, shall be limited to replacement, repair, or refund, as
specified above.
RemedyAndExclusions
The coverage of this Warranty is limited to all components of the Gas
Appliance manufactured by The Companies.
This Warranty only covers Montigo Gas Appliances installed in the
United States or Canada.
If the components of the Gas Appliance covered by this Warranty
are found to be defective within the time frame stated (see The
Companies right of investigation outlined below). The Companies
will, at its option, replace or repair defective components of the Gas
Appliance manufactured by The Companies at no charge, and will
also pay for reasonable labour costs incurred in replacing or repairing
components. If repair or replacement is not commercially practical,
The Companies will, at its option, refund the purchase price of the
Montigo Gas Appliance.
This Warranty covers only parts and labour as provided above. In no
case shall The Companies be responsible for materials, components,
or construction which are not manufactured or supplied by The
Companies, or for the labour necessary to install, repair or remove
such materials, components or construction. All replacement or repair
components will be shipped F.O.B. the nearest The Companies factory.
In no event shall The Companies be responsible for any incidental or
consequential damages caused by defects in its products, whether
such damage occurs or is discovered before or after replacement or
repair, and whether or not such damage is caused by The Companies
negligence. Some states do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitation or
exclusion may not apply to you. The duration of any implied warranty
with respect to this Montigo Gas Appliance is limited to the duration
of the foregoing warranty. Some states do not allow limitation on how
long an implied warranty lasts, so the above may not apply to you.
InvestigationOfClaimsAgainstWarranty
The Companies reserves the right to investigate any and all claims
against this Warranty and to decide upon method of settlement.
The Companies Are Not Responsible For Work Done Without Written
Consent
The Companies shall in no event be responsible for any warranty work
done without first obtaining The Companies written consent.
Dealers Have No Authority To Alter This Warranty
The Companies employees and dealers have no authority to make any
warranties nor to authorize any remedies in addition to or inconsistent
with those stated above.
QualificationsToTheWarranty
HowToRegisterAClaimAgainstWarranty
The Gas Appliance Warranty outlined above is further subject to the
following qualifications:
In order for any claim under this Warranty to be valid, The Companies
must be notified of the claimed defect in writing or by telephone, as
soon as reasonably possible after the defect is discovered. Claims
against this Warranty in writing should include the date of installation,
and a description of the defect.
(1) The Gas Appliance must be installed in accordance with The
Companies installation instructions and local building codes.
The Warranty on this Montigo Gas Appliance covers only the
component parts manufactured by The Companies. The use
of components manufactured by others with this Montigo Gas
Appliance could create serious safety hazards, may result in the
denial of certification by recognized national safety agencies,
and could be in violation of local building codes. This warranty
does not cover any damages occurring from the use of any
components not manufactured or supplied by The Companies
(2) The Montigo Gas Appliance must be subjected to normal use.
The Gas Appliances are designed to burn gas only. Burning
conventional fireplace fuels such as wood, coal or any other
solid fuel will cause damage to the Gas Appliance, will produce
excessive temperatures and will result in a fire hazard.
XG0219 - 170829
OtherRights
This Warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
NOTE: The Companies as stated above refer to - Canadian Heating
Products Inc. and/or Montigo Del Ray Corp.
Canadian Heating Products Inc. and/or Montigo DelRay Corp.
reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors,
styles and products.
Page 43
Appendix
AppendixB:Amendment
(Gas Fireplace / Equipment sold in the State of Massachusetts)
5.08: Modifications to NFPA-54, Chapter 10
(1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as
follows:
Existing chimneys shall be permitted to have their use continued
when a gas conversion burner is installed, and shall be equipped
with a manually reset device that will automatically shut off the gas
to the burner in the event of a sustained back-draft.
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment
installed in every dwelling, building or structure used in whole
or in part for residential purposes, including those owned
or operated by the Commonwealth and where the side wall
exhaust vent termination is less than seven (7) feet above
finished grade in the area of the venting, including but not
limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the
time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gas fitter shall observe that a
hard wired carbon monoxide detector with an alarm and battery
back-up is installed on the floor level where the gas equipment is
to be installed. In addition, the installing plumber or gas fitter shall
observe that a battery operated or hard wired carbon monoxide
detector with an alarm is installed on each additional level of the
dwelling, building or structure served by the side wall horizontal
vented gas fueled equipment. It shall be the responsibility of
the property owner to secure the services of qualified licensed
professionals for the installation of hard wired carbon monoxide
detectors
a. In the event that the side wall horizontally vented gas fueled
equipment is installed in a crawl space or an attic, the hard
wired carbon monoxide detector with alarm and battery backup may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not
be met at the time of completion of installation, the owner
shall have a period of thirty (30) days to comply with the above
requirements; provided, however, that during said thirty (30)
day period, a battery operated carbon monoxide detector with
an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon
monoxide detector as required in accordance with the above
provisions shall comply with NFPA 720 and be ANSI/UL 2042
listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be
permanently mounted to the exterior of the building at a minimum
height of eight (8) feet above grade directly in line with the exhaust
vent terminal for the horizontally vented gas fueled heating
appliance or equipment. The sign shall read, in print size no less
than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW.
KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall
horizontally vented gas fueled equipment shall not approve the
installation unless, upon inspection, the inspector observes carbon
monoxide detectors and signage installed in accordance with the
provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248
CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not
Required To Be Vented” in the most current edition of NFPA 54 as
adopted by the Board; and
2. Product Approved side wall horizontally vented gas fueled
equipment installed in a room or structure separate from the
dwelling, building or structure used in whole or in part for
residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT
VENTING SYSTEM PROVIDED. When the manufacturer
of Product Approved side wall horizontally vented gas
equipment provides a venting system design or venting system
components with the equipment, the instructions provided
by the manufacturer for installation of the equipment and the
venting system shall include:
1. Detailed instructions for the installation of the venting system
design or the venting system components; and
2. A complete parts list for the venting system design or venting
system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT
VENTING SYSTEM NOT PROVIDED. When the manufacturer
of a Product Approved side wall horizontally vented gas fueled
equipment does not provide the parts for venting the flue
gases, but identifies “special venting systems”, the following
requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall
be included with the appliance or equipment installation
instructions; and
2. The “special venting systems” shall be Product Approved by
the Board, and the instructions for that system shall include a
parts list and detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved
side wall horizontally vented gas fueled equipment, all venting
instructions, all parts lists for venting instructions, and/or all
venting design instructions shall remain with the appliance or
equipment at the completion of the installation.
(3) After NFPA-54 section 10.10.4.2 add a new section 10.10.4.3 as
follows:
When more than four gas appliances are to be vented through a
common gas vent or common horizontal vent manifold, a plan of
the proposed vent installation shall be submitted to the Inspector
and the serving gas supplier for review and approval.
Extraction from: Massachusetts Rules and Regulations
5.00: Amendments To 2002 Edition Of ANSI Z223.1-NFPA-54
Page 44
XG0219 - 170829
Notes
XG0219 - 170829
Page 45
PL42VO
PL60VO
Ventless Outdoor Fireplace
XG0219 - 170829