HPE FlexFabric 5800 Switch Series

QuickSpecs
HPE FlexFabric 5800 Switch Series
Overview
HPE FlexFabric 5800 Switch Series
HPE FlexFabric 5800-24G-PoE+ Switch
HPE FlexFabric 5800-24G Switch
HPE FlexFabric 5820X 24XG SFP+ Switch
HPE FlexFabric 5800 48G PoE+ 1-slot Switch
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 1
QuickSpecs
HPE FlexFabric 5800 Switch Series
Overview
HPE FlexFabric 5800 48G 1-slot Switch
HPE FlexFabric 5800 48G POE+ 2-slot Switch
HPE FlexFabric 5800AF 48G Switch
Models
HPE FlexFabric 5800 24G PoE+ Switch
HPE FlexFabric 5800 24G Switch
HPE FlexFabric 5820X 24XG SFP+ Switch
HPE FlexFabric 5800 48G PoE+ 1-slot Switch
HPE FlexFabric 5800 48G 1-slot Switch
HPE FlexFabric 5800 48G POE+ 2-slot Switch
HPE FlexFabric 5800AF 48G Switch
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JC099B
JC100B
JC103B
JC104B
JC105B
JC101B
JG225B
Page 2
QuickSpecs
HPE FlexFabric 5800 Switch Series
Overview
Key features
For enterprise edge, distribution, data center
Cut-through design with low latency
Support for up to 84 ports
OAA module for flexible deployment
Redundant, hot-swappable power supplies, fans
Product overview
The HPE FlexFabric 5800 Switch Series offer an unmatched combination of Gigabit and 10-Gigabit
Ethernet port density, high-availability architecture, and full Layer 2 and Layer 3 dual-stack IPv4 and IPv6
capabilities. In addition to wire-speed line-rate performance on all ports, the switches include patented
Intelligent Resilient Fabric (IRF) technology and Rapid Ring Protection Protocol (RRPP), which allow local
or geographically distributed HPE 5800 switches to be interconnected for higher resiliency and
performance. Available in PoE and non-PoE models as well as 1 RU and 2 RU form factor configurations,
HPE FlexFabric 5800 switches are built on open standards and include an open application architecture
(OAA) module slot that enables flexible deployment options for new services. These versatile switches are
ideal for use in the network core of buildings or departments, or as high-performance switches in the
convergence layer or network edge of enterprise campus networks
Features and benefits
Quality of Service (QoS)
Powerful QoS feature
creates traffic classes based on access control lists (ACLs), IEEE 802.1p precedence, IP, and DSCP
or Type of Service (ToS) precedence; supports filter, redirect, mirror, or remark; supports the following
congestion actions: strict priority (SP) queuing, weighted round robin (WRR), weighted fair queuing
(WFQ), weighted random early discard (WRED), weighted deficit round robin (WDRR), and
SP+WDRR
Integrated network services
with support for open application architecture (OAA) modules, extends and integrates application
capability into the network
Ring Resiliency Protection Protocol (RRPP)
provides fast recovery for ring Ethernet-based topology; provides consistent application performance
for applications such as VoIP
Management
Remote configuration and management
is available through a secure Web browser or a command-line interface (CLI)
IEEE 802.1AB LLDP discovery
advertises and receives management information from adjacent devices on a network, facilitating easy
mapping by network management applications
USB support:
− File copy
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 3
QuickSpecs
HPE FlexFabric 5800 Switch Series
Overview
allows users to copy switch files to and from a USB flash drive
DHCP options:
− DNS Relay and SMTP Redirection
− DHCP: Server (RFC 2131), Client, and Option-82 Relay (RFC 3046)
sFlow
provides scalable, ASIC-based network monitoring and accounting; this allows network operators to
gather a variety of sophisticated network statistics and information for capacity planning and real-time
network monitoring purposes
SNMPv1, v2c, and v3
facilitate centralized discovery, monitoring, and secure management of networking devices
Network Time Protocol (NTP)
synchronizes timekeeping among distributed time servers and clients; keeps consistent timekeeping
among all clock-dependent devices within the network so that the devices can provide diverse
applications based on the consistent time
Connectivity
High-density port connectivity
supports up to 84 1-Gigabit ports per unit (612 per stack)
Auto-MDIX
automatically adjusts for straight-through or crossover cables on all 10/100 ports
Jumbo frames
on Gigabit Ethernet and 10-Gigabit ports, jumbo frames of 9k size allow high-performance remote
backup and disaster-recovery services
IEEE 802.3af Power over Ethernet (PoE)
provides up to 15.4 W per port to IEEE 802.3af-compliant PoE-powered devices such as IP phones,
wireless access points, and security cameras
IEEE 802.3at Power over Ethernet (PoE+) support
simplifies deployment and dramatically reduces installation costs by helping to eliminate the time and
cost involved in supplying local power at each access point location
IPv6 native support
− IPv6 host
enables switches to be managed and deployed at the IPv6 network's edge
− Dual stack (IPv4/IPv6)
transitions from IPv4 to IPv6, supporting connectivity for both protocols
− MLD snooping
forwards IPv6 multicast traffic to the appropriate interface
− IPv6 ACL/QoS
supports ACL and QoS for IPv6 network traffic, preventing traffic flooding
− IPv6 routing
supports IPv6 static routes and IPv6 versions of RIP, OSPF, IS-IS, and BGP routing
protocols
Performance
Hardware-based wire-speed access control lists (ACLs)
feature-rich ACL implementation (TCAM-based) helps provide high levels of security and ease of
administration without impacting network performance
Unique versatile architecture
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 4
QuickSpecs
HPE FlexFabric 5800 Switch Series
Overview
supports the best of both fixed-port and modular configurations
Resiliency and high availability
Data center-optimized design
the HPE 5800AF-48G Switch (JG225B) supports front-to-back/back-to-front airflow for hot/cold aisles,
rear rack mounts, and redundant hot-swappable AC or DC power and fans
Manageability
Full-featured console
provides complete control of the switch with a familiar command-line interface (CLI)
Web interface
allows configuration of the switch from any Web browser on the network
RMON and sFlow
provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events
Multiple configuration files
allow multiple configuration files to be stored to a flash image
Troubleshooting
− Ingress and egress port monitoring
enable network problem solving
− Traceroute and ping
enable testing of network connectivity
− Virtual cable tests
provide visibility to cable problems
Layer 2 switching
GARP VLAN Registration Protocol:
allows automatic learning and dynamic assignment of VLANs
32K MAC addresses
provide access to many Layer 2 devices
4,094 port-based VLANs
provide security between workgroups
IEEE 802.1ad QinQ and Selective QinQ
increase the scalability of an Ethernet network by providing a hierarchical structure; connect multiple
LANs on a high-speed campus or metro network
Gigabit Ethernet port aggregation
allows grouping of ports to increase overall data throughput to a remote device
10 GbE port aggregation
allows grouping of ports to increase overall data throughput to a remote device
Spanning Tree/MSTP, RSTP, and STP Root Guard
prevent network loops
IPFIX/sFlow
allows traffic sampling
Spanning Tree Protocols (STP, MSTP, and RSTP) and STP root guard
helps prevent network loops; up to 32 MSTP instances available
Layer 3 services
Address Resolution Protocol (ARP)
determines the MAC address of another IP host in the same subnet; supports static ARPs; gratuitous
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 5
QuickSpecs
HPE FlexFabric 5800 Switch Series
Overview
ARP allows detection of duplicate IP addresses; proxy ARP allows normal ARP operation between
subnets or when subnets are separated by a Layer 2 network
Dynamic Host Configuration Protocol (DHCP)
simplifies the management of large IP networks and supports client and server; DHCP Relay enables
DHCP operation across subnets
Layer 3 routing
Layer 3 IPv4 routing
provides routing of IPv4 at media speed; supports static routes, RIP and RIPv2, OSPF, IS-IS, and
BGP
RIP and RIPng support
provides complete support of RIP for both IPv4 and IPv6
OSPF and OSPFv3 support
provides complete support of OSPF for both IPv4 and IPv6
IS-IS and IS-ISv6 support
provides complete support of IS-IS for both IPv4 and IPv6
Layer 3 IPv6 routing
provides routing of IPv6 at media speed; supports static routes, RIPng, OSPFv3, IS-ISv6, and BGP4+
Bidirectional Forwarding Detection (BFD)
enables link connectivity monitoring and reduces network convergence time for RIP, OSPF, BGP, ISIS, VRRP, MPLS, and IRF
Virtual Router Redundancy Protocol (VRRP) and VRRP Extended
allow quick failover of router ports
Policy-based routing
makes routing decisions based on policies set by the network administrator
IGMPv1, v2, and v3
allow individual hosts to be registered on a particular VLAN
PIM-SSM, PIM-DM, and PIM-SM (for IPv4 and IPv6)
support IP Multicast address management and inhibition of DoS attacks
Equal-Cost Multipath (ECMP)
enables multiple equal-cost links in a routing environment to increase link redundancy and scale
bandwidth
NEW MPLS support
provides extended support of MPLS, including MPLS VPNs and MPLS Traffic Engineering (MPLS TE)
NEW VPLS support
provides extended support of VPLS for data center to data center communication at Layer 2; provides
support of hierarchical VPLS for scalability
Security
Unicast Reverse Path Forwarding (URPF)
allows normal packets to be forwarded correctly, but discards the attaching packet due to lack of
reverse path route or incorrect inbound interface; prevents source spoofing and distributed attacks;
supports distributed UFPF
Defense-in-depth security
provides integrated and distributed security enforcement that can be managed from a central location,
such as the HPE Intelligent Management Center (IMC)
Advanced processor queuing mechanism
helps prevent denial-of-service (DoS) attacks, while DHCP snooping helps ensure that devices can
only receive an IP address from a legitimate DHCP server on the network
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 6
QuickSpecs
HPE FlexFabric 5800 Switch Series
Overview
IEEE 802.1X-based dynamic delivery of QoS, ACLs, and VLANs
allows complete control over user network access
Guest VLAN
similar to IEEE 802.1X, it provides a browser-based environment to authenticated clients
Port isolation
secures and adds privacy, and prevents malicious attackers from obtaining user information
MAC-based authentication
allows or denies access to the switch based on client MAC address
HTTPS management
provides secure Web management
Multi-Customer Edge (MCE)-Multicast Virtual Routing and Forwarding (MVRF)
provide MPLS Edge router support
Public Key Infrastructure (PKI)
is used to control access
RADIUS/HWTACACS
eases switch management security administration by using a password authentication server
Secure Shell (SSHv2)
encrypts all transmitted data for secure, remote CLI access over IP networks
IP Source Guard
helps prevent IP spoofing attacks; filters packets on a per-port basis, which prevents illegal packets
from being forwarded
Access control lists (ACLs)
helps provide high levels of security and ease of administration; 6k ingress entries and 1k egress
entries (IPv4 and IPv6)
Convergence
Voice VLAN
automatically assigns VLAN and priority for IP phones, simplifying network configuration and
maintenance
Internet Group Management Protocol (IGMP)
is used by IP hosts to establish and maintain multicast groups; supports v1, v2, and v3; utilizes AnySource Multicast (ASM) or Source-Specific Multicast (SSM) to manage IPv4 multicast networks
Protocol Independent Multicast (PIM)
defines modes of Internet multicasting to allow one-to-many and many-to-many transmission of
information; supports PIM Dense Mode (DM), Sparse Mode (SM), and Source-Specific Multicast(SSM)
LLDP-MED (Media Endpoint Discovery)
defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to
configure automatically network devices such as IP phones
Monitor and diagnostics
Port mirroring
enables traffic on a port to be simultaneously sent to a network analyzer for monitoring
OAM (IEEE 802.3ah)
operational, administration and maintenance (OAM) management capabilities detects data link layer
problems that occurred in the "last mile"; monitors the status of the link between the two devices
CFD (IEEE 802.1ag)
connectivity fault detection (CFD) provides a Layer 2 link OAM mechanism used for link connectivity
detection and fault locating
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 7
QuickSpecs
HPE FlexFabric 5800 Switch Series
Overview
Additional information
HPE Intelligent Resilient Fabric (IRF)
− Creates virtual resilient switching fabrics, where two or more switches perform as a single Layer
2 switch and Layer 3 router
− Switches do not have to be co-located and can be part of a disaster-recovery system
− Servers or switches can be attached using standard LACP for automatic load balancing and
high availability
− Simplifies network operation by eliminating the complexity of Spanning Tree Protocol, ECMP, or
VRRP
OAA modules
support wireless network management and high-performance security applications; leverage network
infrastructure investment
Green IT and power
use the latest advances in silicon development, shut off unused ports, and use variable-speed fans to
improve energy efficiency
Higher scalability with IRF
simplifies the architecture of server access networks and reduces cost and complexity; up to nine 5800
Switches can be combined to deliver unmatched scalability of virtualized access layer switches and
flatter, two-tier FlexFabric networks
Warranty and support
Limited Lifetime warranty
See http://www.hpe.com/networking/warrantysummary for warranty and support information
included with your product purchase.
Software releases
to find software for your product, refer to http://www.hpe.com/networking/support; for details on the
software releases available with your product purchase, refer to
http://www.hpe.com/networking/warrantysummary
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 8
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
Build To Order:
BTO is a standalone unit with no integration. BTO products ship standalone are not part of a CTO or RackShippable solution.
Standard Switch Chassis
HPE FlexFabric 5800 24G Switch
24 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U - Height
JC100B
See
Configuration
NOTE:1, 3, 7
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC100B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC100B#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JC100B#B2E
HPE FlexFabric 5800 24G PoE+ Switch
24 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U - Height
JC099B
See
Configuration
NOTE:1, 3, 7
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC099B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC099B#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JC099B#B2E
HPE FlexFabric 5820X 24XG SFP+ Switch
24 100/1000 SFP ports
min=0 \ max=24 SFP Transceivers
1 extended module slot
4 fixed 1000/10000 SFP+ ports
JC103B
See
Configuration
NOTE:1, 4
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 9
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
min=0 \ max=4 SFP+ Transceivers
Must select min 1 Power Supply
1U - Height
HPE FlexFabric 5800 48G 1-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U- Height
JC105B
See
Configuration
NOTE:1, 3, 7
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC105B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC105B#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JC105B#B2E
HPE FlexFabric 5800AF 48G Switch
48 RJ-45 autosensing 10/100/1000 ports
6 fixed 1000/10000 SFP+ ports
min=0 \ max=6 SFP+ Transceivers
Must select min 1 Power Supply
Must select min 2 Fan Trays
1U- Height
JG225B
See
Configuration
NOTE:1
HPE FlexFabric 5800 48G PoE+ 1-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U - Height
JC104B
See
Configuration
NOTE:1, 3, 7
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC104B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC104B#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JC104B#B2E
HPE FlexFabric 5800 48G POE+ 2-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JC101B
See
Page 10
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
2 extended module slot
4 fixed 1000 SFP ports
min=0 \ max=4 SFP Transceivers
Must select min 1 Power Supply
2U - Height
Configuration
NOTE:4
Configuration Rules
Note 1
The following Transceivers install into this switch:
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LRM Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X130 10G SFP+ LC SR Data Center Transceiver
HPE X130 10G SFP+ LC LRM Data Center Transceiver
HPE X130 10G SFP+ LC LR Data Center Transceiver
HPE X130 10G SFP+ LC ER 40km Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
Note 3
Localization required on orders without #B2B, #B2C or #B2E options.
Note 4
The following Transceivers install into this Switch:
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X110 100M SFP LC LH40 Transceiver
HPE X110 100M SFP LC LH80 Transceiver
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X125 1G SFP LC LH70 Transceiver
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JD092B
JD093B
JD094B
JL437A
JL438A
JL439A
JG234A
JD061A
JD062A
JD118B
JD119B
JD063B
JD089B
JD095C
JD096C
JD097C
JH693A
JH694A
JH695A
JG081C
JD061A
JD062A
JD089B
JD118B
JD119B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
JD063B
Page 11
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
Note 7
#B2E is Offered only NA, Mexico, Taiwan, and Japan.
Box Level Integration CTO Models
CTO Solution Sku
HPE FlexFabric 58xx Configure-to-order Switch Solution
SSP trigger sku
JG478A
CTO Base Sku
HPE FlexFabric 5800 24G Switch
24 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U - Height
JC100B
See
Configuration
NOTE:1, 3,
9, 10, 11
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC100B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC100B#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JC100B#B2E
HPE FlexFabric 5800 24G PoE+ Switch
24 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U - Height
JC099B
See
Configuration
NOTE:1, 3,
9, 10, 11
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC099B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC099B#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JC099B#B2E
HPE FlexFabric 5820X 24XG SFP+ Switch
JC103B
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 12
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
24 100/1000 SFP ports
min=0 \ max=24 SFP Transceivers
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Must select min 1 Power Supply
1U - Height
See
Configuration
NOTE:1, 4,
5, 10
HPE FlexFabric 5800 48G 1-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U- Height
JC105B
See
Configuration
NOTE:1, 3,
9, 10, 11
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC105B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC105B#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JC105B#B2E
HPE FlexFabric 5800AF 48G Switch
48 RJ-45 autosensing 10/100/1000 ports
6 fixed 1000/10000 SFP+ ports (min=0 \ max=6 SFP+ Transceivers)
Must select min 1 Power Supply
Must select min 2 Fan Trays
1U - Height
JG225B
See
Configuration
NOTE:1, 8,
10
HPE FlexFabric 5800 48G PoE+ 1-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U - Height
JC104B
See
Configuration
NOTE:1, 3,
9, 10, 11
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC104B#B2B
C15 PDU ROW
C15 PDU Jumper Cord (ROW)
JC104B#B2C
High Volt Switch to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JC104B#B2E
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 13
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
HPE FlexFabric 5800 48G POE+ 2-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
2 extended module slot
4 fixed 1000 SFP ports
min=0 \ max=4 SFP Transceivers
Must select min 1 Power Supply
2U - Height
JC101B
See
Configuration
NOTE:4,
5,10
Configuration Rules
Note 1
The following Transceivers install into this switch: (Use #0D1 or #B01 if switch is
CTO) If Applicable HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LRM Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X130 10G SFP+ LC SR Data Center Transceiver
HPE X130 10G SFP+ LC LRM Data Center Transceiver
HPE X130 10G SFP+ LC LR Data Center Transceiver
HPE X130 10G SFP+ LC ER 40km Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
Note 3
Localization required on orders without #B2B, #B2C or #B2E options.
Note 4
The following Transceivers install into this Switch: (Use #0D1 if switch is CTO) If
Applicable HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X110 100M SFP LC LH40 Transceiver
HPE X110 100M SFP LC LH80 Transceiver
HPE X115 100M SFP LC FX Transceiver
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JD092B
JD093B
JD094B
JL437A
JL438A
JL439A
JG234A
JD061A
JD062A
JD118B
JD119B
JD063B
JD089B
JD095C
JD096C
JD097C
JH693A
JH694A
JH695A
JG081C
JD061A
JD062A
JD089B
JD118B
JD119B
JD090A
JD091A
JD102B
Page 14
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
Note 5
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X125 1G SFP LC LH70 Transceiver
JD120B
JD100A
JD101A
JD063B
If this Switch is selected at least one of these Power Supply with #0D1 is
required:
HPE 5800 300W AC Power Supply
HPE 5800 750W AC Power Supply
JC087A
JC089A
Note 8
If this Switch is selected at least one of these Power Supply with #0D1 is required:
HPE 58x0AF 650W AC Power Supply
JC680A
Note 9
B2E is Offered only in . NA, Mexico, Taiwan, and Japan.
Note 10
If the Switch Chassis is to be Box Level Factory Integrated (CTO), Then the #0D1 is required
on the Switch Chassis and integrated to the JG478A - HPE FlexFabric 58xx Configure-to-order
Switch Solution. (Min 1/Max 1 Switch per SSP)
Note 11
If this Switch is selected, Then a Minimum of 1 factory integrated accessory, OR Factory
Service, must be ordered and integrated to CTO chassis. See Menu below, option must have a
#0D1 to be integrated to the CTO Chassis.
Rack Level Integration CTO Models
Standard Switch Chassis
HPE FlexFabric 5800 24G Switch
24 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U - Height
JC100B
See
Configuration
NOTE:1, 3, 10
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC100B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC100B#B2C
HPE FlexFabric 5800 24G PoE+ Switch
24 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
JC099B
See
Configuration
NOTE:1, 3, 10
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 15
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
1U - Height
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC099B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC099B#B2C
HPE FlexFabric 5820X 24XG SFP+ Switch
24 100/1000 SFP ports
min=0 \ max=24 SFP Transceivers
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Must select min 1 Power Supply
1U - Height
JC103B
See
Configuration
NOTE:1, 4, 10
HPE FlexFabric 5800 48G 1-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U- Height
JC105B
See
Configuration
NOTE:1, 3, 10
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC105B#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC105B#B2C
HPE FlexFabric 5800AF 48G Switch
48 RJ-45 autosensing 10/100/1000 ports
6 fixed 1000/10000 SFP+ ports (min=0 \ max=6 SFP+ Transceivers)
Must select min 1 Power Supply
Must select min 2 Fan Trays
1U - Height
JG225B
See
Configuration
NOTE:1, 10
HPE FlexFabric 5800 48G PoE+ 1-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
min=0 \ max=4 SFP+ Transceivers
Power Supply included
1U - Height
JC104B
See
Configuration
NOTE:1, 3, 10
PDU Cable NA/MEX/TW/JP
JC104B#B2B
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 16
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
C15 PDU Jumper Cord (NA/MEX/TW/JP)
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC104B#B2C
HPE FlexFabric 5800 48G POE+ 2-slot Switch
48 RJ-45 autosensing 10/100/1000 ports
2 extended module slot
4 fixed 1000 SFP ports
min=0 \ max=4 SFP Transceivers
Must select min 1 Power Supply
2U - Height
JC101B
See
Configuration
NOTE:4, 10
Configuration Rules:
Note 1
The following Transceivers install into this switch:
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LRM Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X130 10G SFP+ LC SR Data Center Transceiver
HPE X130 10G SFP+ LC LRM Data Center Transceiver
HPE X130 10G SFP+ LC LR Data Center Transceiver
HPE X130 10G SFP+ LC ER 40km Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JD092B
JD093B
JD094B
JL437A
JL438A
JL439A
JG234A
JD061A
JD062A
JD118B
JD119B
JD063B
JD089B
JD095C
JD096C
JD097C
JH693A
JH694A
JH695A
JG081C
Note 3
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) .
(See Localization Menu)
REMARK: When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the
Defaulted Power Cable option on the Switches/Routers.
Note 4
The following Transceivers install into this Switch:
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JD061A
JD062A
Page 17
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X110 100M SFP LC LH40 Transceiver
HPE X110 100M SFP LC LH80 Transceiver
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X125 1G SFP LC LH70 Transceiver
Note 10
JD089B
JD118B
JD119B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
JD063B
If HPE CTO Switch Chassis is selected for Rack Level Integration, Then the Switch needs to
integrate (with #0D1) to the HPE Rack.
Enter the following menu selections as integrated to the CTO Model X server above if order is
factory built.
Modules
Ethernet Modules
(JC101x, JG242x, Switch Only ) System (std 0 // max 2) User Selection (min 0 // max 2) per
chassis
(JC100x, JC099x, JC103x, JC105x, JC104x, JG254x, JG255x, JG256x, JG257x, JG258x, Switch Only )
System (std 0 // max 1) User Selection (min 0 // max 1) per chassis
HPE 5800 16-port SFP Module
min=0 \ max=16 SFP Transceivers
JC095A
See
Configuration
NOTE:2
HPE 5800 4-port 10GbE SFP+ Module
min=0 \ max=4 SFP and SFP + Transceivers
JC091A
See
Configuration
NOTE:1
HPE 5800 2-port 10GbE SFP+ Module
min=0 \ max=2 SFP and SFP + Transceivers
JC092B
See
Configuration
NOTE:1
HPE 5800 16-port Gig-T Module
No Transceivers
JC094A
Configuration Rules:
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 18
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
Note 1
Note 2
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
If Applicable HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LRM Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X130 10G SFP+ LC SR Data Center Transceiver
HPE X130 10G SFP+ LC LRM Data Center Transceiver
HPE X130 10G SFP+ LC LR Data Center Transceiver
HPE X130 10G SFP+ LC ER 40km Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JD092B
JD093B
JD094B
JL437A
JL438A
JL439A
JG234A
JD061A
JD062A
JD118B
JD119B
JD063B
JD089B
JD095C
JD096C
JD097C
JH693A
JH694A
JH695A
JG081C
The following Transceivers install into this Module: (Use #0D1 if switch is CTO)
If Applicable HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X110 100M SFP LC LH40 Transceiver
HPE X110 100M SFP LC LH80 Transceiver
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X125 1G SFP LC LH70 Transceiver
JD061A
JD062A
JD089B
JD118B
JD119B
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
JD063B
Access Control Modules
(JC101x and JG242x Switch Only ) System (std 0 // max 1) User Selection (min 0 // max 1)
per chassis
HPE 5820 VPN Firewall Module
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JD255A
Page 19
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
No Transceivers
See
Configuration
NOTE:1
Configuration Rules:
Note 1
This Module install to the following switches only:
JC101x - HPE 5800-48G Switch with 2 Slots
PoE Modules
(JC101x and JG242x Switch Only ) System (std 0 // max 1) User Selection (min 0 // max 1)
per chassis
HPE 5800 PoE Module
No Transceivers
JC097B
Transceivers
SFP+ Transceivers
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LRM Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X130 10G SFP+ LC SR Data Center Transceiver
HPE X130 10G SFP+ LC LRM Data Center Transceiver
HPE X130 10G SFP+ LC LR Data Center Transceiver
HPE X130 10G SFP+ LC ER 40km Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Campus-Cable
HPE X240 10G SFP+ to SFP+ 3m Direct Attach Copper Campus-Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
JD092B
JD093B
JD094B
JL437A
JL438A
JL439A
JG234A
JD095C
JD096C
JD097C
JH693A
JH694A
JH695A
JG081C
SFP Transceivers
HPE X110 100M SFP LC LH40 Transceiver
HPE X110 100M SFP LC LH80 Transceiver
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X120 1G SFP RJ45 T Transceiver
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JD090A
JD091A
JD102B
JD120B
JD100A
JD101A
JD062A
JD089B
Page 20
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X125 1G SFP LC LH70 Transceiver
JD118B
JD119B
JD061A
JD063B
Internal Power Supplies
(JC103x and JG256x Only) System (std 0 // max 2) User Selection (min 1 // max 2) per
switch
(JC101x and JG242x Only) System (std 0 // max 2) User Selection (min 1 // max 2) per
switch
(JG225B only) System (std 0 // max 2) User Selection (min 1 // max 2) per switch
HPE 5500 150WAC Power Supply
JD362A
See
Configuration
NOTE:1, 2, 3
PDU Cable NA/MEX/TW/JP
C13 PDU Jumper Cord (NA/MEX/TW/JP)
JD362A#B2B
PDU Cable ROW
C13 PDU Jumper Cord (ROW)
JD362A#B2C
HPE X361 150W 100-240VAC to 12VDC Power Supply
includes 1 x c13, 910w
JD362B
See
Configuration
NOTE:1, 2, 3
PDU Cable NA/MEX/TW/JP
C13 PDU Jumper Cord (NA/MEX/TW/JP)
JD362B#B2B
PDU Cable ROW
C13 PDU Jumper Cord (ROW)
JD362B#B2C
High Volt Switch to Wall Power Cord
HPE 2.3M C13 to NEMA L6-20P Power Cord (J9936A)
JD362B#B2E
No Power Cord
No Localized Power Cord Selected
JD362B#AC3
HPE FlexNetwork 5500 150WDC Power Supply
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JD366A
Page 21
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
See
Configuration
NOTE:1, 3
HPE X361 150W 48-60VDC to 12VDC Power Supply
JD366B
See
Configuration
NOTE:1, 3
HPE 5800 300W AC Power Supply
JC087A
See
Configuration
NOTE:1, 2, 4
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC087A#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC087A#B2C
HPE 5800 300W DC Power Supply
JC090A
See
Configuration
NOTE:1, 4
HPE 5800 750W AC Power Supply
JC089A
See
Configuration
NOTE:1, 2, 4
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC089A#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JC089A#B2C
HPE 58x0AF 650W AC Power Supply
includes 1 x c13, 650w
JC680A
See
Configuration
NOTE:1, 2, 6
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JC680A#B2B
JC680A#B2C
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 22
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
HPE A58x0AF Back (Power Side) to Front (Port Side) Airflow 300W AC Power Supply
includes 1 x c13, 300w
JG900A
See
Configuration
NOTE:1, 2, 6
PDU Cable NA/MEX/TW/JP
C15 PDU Jumper Cord (NA/MEX/TW/JP)
JG900A#B2B
PDU Cable ROW
C15 PDU Jumper Cord (ROW)
JG900A#B2C
High Volt Switch/Router to Wall Power Cord
NEMA L6-20P Cord (NA/MEX/JP/TW)
JG900A#B2E
HPE A58x0AF Back (Power Side) to Front (Port Side) Airflow 300W DC Power Supply
JG901A
See
Configuration
NOTE:1, 6, 7
HPE FlexFabric Switch 650W 48V Hot Plug NEBS-compliant DC Power Supply
JH336A
See
Configuration
NOTE:1, 6
Configuration Rules:
Note 1
If 2 power supplies are selected then they must be the same Sku number.
Note 2
Localization (Wall Power Cord) required on orders without #B2B, #B2C (PDU Power Cord) .
(See Localization Menu)
REMARK: When Switches/Routers are Factory Racked, Then #B2B, or #B2C should be the
Defaulted Power Cable option on the Switches/Routers.
Note 3
This power supply only supported on JC103x and JG256x Only.
Note 4
This power supply only supported on JC101x and JG242x Only.
Note 6
This power supply only supported on JG225B Only.
Note 7
Watson Only - Add "(NEBS)" after the description on the PS table.
Remarks:
Drop down under power supply should offer the following options and results:
Switch/Router/Power Supply to PDU Power Cord - #B2B in North America, Mexico, Taiwan,
and Japan or #B2C ROW. (Watson Default B2B or B2C for Rack Level CTO)
Switch/Router/Power Supply to Wall Power Cord - Localized Option (Watson Default for BTO
and Box Level CTO)
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 23
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
NOTE* Switch JG225B should default selection of Power Supply as JC680A but allow
selection of JG900A, JG901A, and JC681A.
Switch Options
Fan Trays
(JG225B only) System (std 0 // max 2) User Selection (min 2 // max 2) per switch
HPE 58x0AF Back (Power Side) to Front (Port Side) Airflow Fan Tray
JC682A
See
Configuration
NOTE:1
HPE 58x0AF Front (Port Side) to Back (Power Side) Airflow Fan Tray
JC683A
See
Configuration
NOTE:1
Configuration Rules:
Note 1
Fan Trays cannot be mixed in the same switch enclosure
Remark:
Watson Blue Text:
If there is any empty space below the switch in a rack when using Back to Front Fan Trays,
JC682A, the rack will receive an Air Plenum kit that takes up 1U of additional space in the rack.
The Air Plenum kit is not required on fully configured racks. This only applies for CTO Rack
Level Integration. The Air Plenum Kit is a non-saleable SKU, and is brought in automatically for
CTO Factory Rack Level Integration.
Fan Options
HPE 5800 2RU Spare Fan Assembly
HPE 5800 1RU Spare Fan Assembly
JC096A
See
Configuration
NOTE:1
JC098A
See
Configuration
NOTE:2
Configuration Rules:
Note 1
This Spare Fan is only supported on switches JC101B and JG242B.
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 24
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
Note 2
This Spare Fan is only supported on switches JC099B, JC100B, JC103B, JC104B, JC105B,
JG254B, JG255B, JG256B, JG257B and JG258B.
Opacity Shield Kit
System (std 0 // max 1) User Selection (min 0 // max 1)
HPE 5800 24G/48G PoE Opacity Shield Kit
Supported on JG254B, JG257B
JG560A
See
Configuration
NOTE:1
HPE 58xx 2-slot Switch Opacity Shield Kit
Supported on JG242B
JG561A
See
Configuration
NOTE:1
HPE 5800 24G SFP Opacity Shield Kit
Supported on JG256B
JG562A
See
Configuration
NOTE:1
HPE 5800 24G/48G Opacity Shield Kit
Supported on JG255B, JG258B
JG563A
See
Configuration
NOTE:1
Configuration Rules:
Note 1
If selected with a CTO Switch Solution, Quantity 1 of JG585A#B01 must also be
ordered.
Tamper Evidence Labels
System (std 0 // max 1) User Selection (min 0 // max 1)
HPE 12mm x 60mm Tamper Evidence (30) Labels
Supported on JG254B, JG257B, JG242B, JG256B, JG255B, JG258B
JG585A
See
Configuration
NOTE:1
Configuration Rules:
Note 1
If selected with a CTO Switch Solution, Quantity 1 of JG560A#B01,
JG561A#B01, JG562A#B01 or JG563A#B01 must also be ordered.
Remarks Each JG560A, JG561A, JG562A or JG563A would use 1 of JG585A.
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 25
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
License
HPE WX5000 32 Access Point License Upgrade
JD463A
See
Configuration
NOTE:1
Configuration Rules:
Note 1
If this license is selected, Then one of these modules should be selected or be
on site:
HPE 5800 Access Controller Module for 32-64 Access Points
HPE 5800 Access Controller Module for 64-256 Access Points
JD443A
JD441A
External Redundant Power Supplies
HPE RPS 800 Redundant Power Supply
Height = 1U
includes 1 x c13
JD183A
See
Configuration
NOTE:2, 4
HPE RPS1600 Redundant Power System
Height = 1U
includes 1 x c13, 1600w and Power Supply port
JG136A
See
Configuration
NOTE:2, 3, 5
HPE RPS1600 1600W AC Power Supply
Installs into JG136A only
JG137A
See
Configuration
NOTE:1, 3
Configuration Rules:
Note 1
If this power supply is selected, The JG136A - HPE RPS1600 Redundant Power System must
be on order or onsite.
Note 2
Localization required.
Note 3
Each switch will only support 1 JG136A and 1 JG137A Power supply systems.
Note 4
This power supply only supported on switches JC105B and JC100B.
Note 5
This power supply only supported on switches JC099B, JC101B, JC103B, JC104B.
Options for the HPE RPS 800 and 1600 External RPS Power Supplies
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 26
QuickSpecs
HPE FlexFabric 5800 Switch Series
Configuration
HPE X290 1000 A JD5 2m RPS Cable
JD187A
See
Configuration
NOTE:3
HPE X290 1000 A JD5 NonPoE 2m RPS Cable
JD188A
See
Configuration
NOTE:2
HPE X290 1000 B JD5 2m RPS Cable
JD189A
See
Configuration
NOTE:4
HPE X290 500/800 1m RPS Cable
JD190A
See
Configuration
NOTE:1
Configuration Rules:
Note 1
This Cable is only supported on switches JC105B and JC100B when used with the RPS 800
(JD183A)
Note 2
This Cable is only supported on switch JC103B when used with the RPS 1600 (JG136A)
Note 3
This Cable is only supported on switches JC099B, JC101B, JC104B, and when used with the
RPS 1600 (JG136A).
Note 4
This Cable is only supported on switches JC101B (Running On Non-PoE mode), JC103B when
used with the RPS 1600 (JG136A)
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 27
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
HPE FlexFabric 5800 24G PoE+ Switch (JC099B)
Ports
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only
1 extended module slot
4 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
Physical
Dimensions
17.3(w) x 16.8(d) x 1.71(h) in (43.94 x 42.67 x 4.34 cm) (1U
height)
characteristics
Weight
17.64 lb (8 kg)
Memory and
2048 MB SDRAM; Packet buffer size: 4 MB, 512 MB flash
processor
Performance
Latency
4.02 µs (Store and Forward) (64-byte packets)
Throughput
up to 155 Mpps
Routing/Switching 208 Gbps
capacity
Routing table size 16000 entries
MAC address table 32000 entries
size
Environment
Operating
32°F to 113°F (0°C to 45°C)
temperature
Operating relative 10% to 90%
humidity
Acoustic
Low-speed fan: 47.5 dB, High-speed fan: 52.4 dB
Electrical
Maximum heat
2968 BTU/hr (3131.24 kJ/hr)
characteristics
dissipation
Voltage
100 - 120 / 200 - 240 VAC, rated
Frequency
50/60 Hz
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR;
GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance
Emissions
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR22 Class A; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
Immunity
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 28
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Management
Services
Power frequency
IEC 61000-4-8; EN 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11; IEC 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP
Manager; Telnet; HTTPS; RMON1; FTP
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services
for details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexFabric 5800 24G Switch (JC100B)
Ports
24 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only
1 extended module slot
4 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
Physical
Dimensions
17.32(w) x 14.35(d) x 1.72(h) in (44.0 x 36.45 x 4.36 cm) (1U
height)
characteristics
Weight
13.23 lb (6 kg)
Memory and
2048 MB SDRAM; Packet buffer size: 4 MB, 512 MB flash
processor
Performance
Latency
4.02 µs (Store and Forward) (64-byte packets)
Throughput
up to 155 Mpps
Routing/Switching 208 Gbps
capacity
Routing table size 16000 entries
MAC address table 32000 entries
size
Environment
Operating
32°F to 113°F (0°C to 45°C)
temperature
Operating relative 10% to 90%
humidity
Acoustic
Low-speed fan: 42.3 dB, High-speed fan: 52.9 dB
Electrical
Maximum heat
358 BTU/hr (377.69 kJ/hr)
characteristics
dissipation
Voltage
100 - 120 - 240 VAC, rated
Frequency
50/60 Hz
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 29
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Safety
Emissions
Immunity
Management
Services
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR;
GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR22 Class A; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency
IEC 61000-4-8; EN 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11; IEC 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP
Manager; Telnet; HTTPS; RMON1; FTP
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services
for details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexFabric 5820X 24XG SFP+ Switch (JC103B)
Ports
24 SFP fixed Gigabit Ethernet SFP ports
1 extended module slot
4 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
Power supplies
2 power supply slots
1 minimum power supplies required (ordered separately)
Physical
Dimensions
17.32(w) x 16.81(d) x 1.72(h) in (44.0 x 42.7 x 4.36 cm) (1U
height)
characteristics
Weight
18.74 lb (8.5 kg)
Memory and
2048 MB SDRAM; Packet buffer size: 8 MB, 512 MB flash
processor
Performance
Latency
4.02 µs (Store and Forward) (64-byte packets)
Throughput
up to 155 Mpps
Routing/Switching 208 Gbps
capacity
Routing table size 16000 entries
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 30
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Environment
Electrical
characteristics
Safety
Emissions
Immunity
Management
Notes
Services
MAC address table 32000 entries
size
Operating
32°F to 113°F (0°C to 45°C)
temperature
Operating relative 10% to 90%
humidity
Acoustic
Low-speed fan: 49.6 dB, High-speed fan: 58.1 dB
Maximum heat
498 BTU/hr (525.39 kJ/hr)
dissipation
Voltage
100 - 120 / 200 - 240 VAC, rated
DC voltage
-48 VDC to -60 VDC
Frequency
50/60 Hz
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR;
GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR22 Class A; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency
IEC 61000-4-8; EN 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11; IEC 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP
Manager; Telnet; HTTPS; RMON1; FTP
The customer must order a power supply, as the device does not come with a PSU.
At least one JD362A/JD362B or JD366A/JD366B is required.
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services
for details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexFabric 5800 48G PoE+ 1-slot Switch (JC104B)
Ports
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASEDA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 31
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Physical
characteristics
Memory and
processor
Performance
Environment
Electrical
characteristics
Safety
Emissions
Immunity
T/100BASE-TX: half or full; 1000BASE-T: full only
1 extended module slot
4 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
Dimensions
17.32(w) x 16.81(d) x 1.72(h) in (44.0 x 42.7 x 4.36 cm) (1U
height)
Weight
18.74 lb (8.5 kg)
2048 MB SDRAM; Packet buffer size: 8 MB, 512 MB flash
Latency
4.02 µs (Store and Forward) (64-byte packets)
Throughput
up to 190 Mpps
Routing/Switching 256 Gbps
capacity
Routing table size 16000 entries
MAC address table 32000 entries
size
Operating
32°F to 113°F (0°C to 45°C)
temperature
Operating relative 10% to 90%
humidity
Acoustic
Low-speed fan: 50.5 dB, High-speed fan: 57.9 dB
Maximum heat
3320 BTU/hr (3502.6 kJ/hr)
dissipation
Voltage
100 - 120 / 200 - 240 VAC, rated
Frequency
50/60 Hz
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR;
GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR22 Class A; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency
IEC 61000-4-8; EN 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11; IEC 61000-4-11
interruptions
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 32
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Management
Services
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP
Manager; Telnet; HTTPS; RMON1; FTP
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services
for details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexFabric 5800 48G 1-slot Switch (JC105B)
Ports
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only
1 extended module slot
4 fixed 1000/10000 SFP+ ports
1 RJ-45 serial console port
Physical
Dimensions
17.32(w) x 14.45(d) x 1.72(h) in (44.0 x 36.7 x 4.36 cm) (1U
height)
characteristics
Weight
14.33 lb (6.5 kg)
Memory and
2048 MB SDRAM; Packet buffer size: 8 MB, 512 MB flash
processor
Performance
Latency
4.02 µs (Store and Forward) (64-byte packets)
Throughput
up to 190 Mpps
Routing/Switching 256 Gbps
capacity
Routing table size 16000 entries
MAC address table 32000 entries
size
Environment
Operating
32°F to 113°F (0°C to 45°C)
temperature
Operating relative 10% to 90%
humidity
Acoustic
Low-speed fan: 45.3 dB, High-speed fan: 56.5 dB
Electrical
Maximum heat
557 BTU/hr (587.64 kJ/hr)
characteristics
dissipation
Voltage
100 - 120 / 200 - 240 VAC, rated
Frequency
50/60 Hz
Safety
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR;
GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance
Emissions
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR22 Class A; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 33
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Immunity
Management
Services
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency
IEC 61000-4-8; EN 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11; IEC 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP
Manager; Telnet; HTTPS; RMON1; FTP
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services
for details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexFabric 5800 48G POE+ 2-slot Switch (JC101B)
Ports
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only
2 extended module slots
1 open module slot
4 SFP fixed Gigabit Ethernet SFP ports
1 RJ-45 serial console port
Power supplies
2 power supply slots
1 minimum power supplies required (ordered separately)
Physical
Dimensions
17.32(w) x 18.31(d) x 3.39(h) in (44.0 x 46.5 x 8.61 cm) (2U
height)
characteristics
Weight
39.7 lb (18.0 kg)
Memory and
2048 MB SDRAM; Packet buffer size: 8 MB, 512 MB flash
processor
Performance
Latency
4.02 µs (Store and Forward) (64-byte packets)
Throughput
up to 211 Mpps
Routing/Switching 284 Gbps
capacity
Routing table size 16000 entries
MAC address table 32000 entries
size
Environment
Operating
32°F to 113°F (0°C to 45°C)
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 34
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Electrical
characteristics
Safety
Emissions
Immunity
Management
Notes
Services
temperature
Operating relative
humidity
Acoustic
Maximum heat
dissipation
Voltage
DC Voltage
10% to 90%
Low-speed fan: 54 dB, High-speed fan: 58.5 dB
6278 BTU/hr (6623.29 kJ/hr)
100 - 120 / 200 - 240 VAC, rated
300 W DC: -48 VDC to -60 VDC; 750 W DC: -54 VDC to -57
VDC
Frequency
50/60 Hz
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR;
GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR22 Class A; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency
IEC 61000-4-8; EN 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11; IEC 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP
Manager; Telnet; HTTPS; RMON1; FTP
Customer must order power supply, as the device does not come with a PSU. At
least one JC087A/JC090A/JC089A is required.
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services
for details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
HPE FlexFabric 5800AF 48G Switch (JG225B)
Ports
48 RJ-45 autosensing 10/100/1000 ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u
Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T); Duplex: 10BASET/100BASE-TX: half or full; 1000BASE-T: full only
6 fixed 1000/10000 SFP+ ports
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 35
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Power supplies
Fan tray
Physical
characteristics
Memory and
processor
Performance
Environment
Electrical
characteristics
Safety
Emissions
Immunity
1 RJ-45 serial console port
1 RJ-45 out-of-band management port
1 USB 2.0
2 power supply slots
1 minimum power supply required (ordered separately)
2 fan tray slots
The customer must order fan trays, as fan trays are not included with the switch. This
system requires two same-direction airflow fan trays to function properly. The system
should not be operated with only one fan tray for more than 24 hours. The system
should not be operated without a fan tray more than two minutes. The system should
not be operated outside of the temperature range of 32°F (0°C) to 113°F (45°C).
Failure to comply with these operating requirements may void the product warranty.
Dimensions
17.32(w) x 25.98(d) x 1.72(h) in (43.99 x 65.99 x 4.37 cm) (1U
height)
Weight
22.05 lb (10 kg), Fully loaded
2048 MB flash; Packet buffer size: 8 MB, 512 MB SDRAM
Latency
< 5 µs (64-byte packets)
Throughput
up to 161 Mpps
Routing/Switching 216 Gbps
capacity
Routing table size 16000 entries
MAC address table 32000 entries
size
Operating
32°F to 113°F (0°C to 45°C)
temperature
Operating relative 10% to 90%
humidity
Acoustic
Low-speed fan: 60.1 dB, High-speed fan: 69.9 dB
Maximum heat
426 BTU/hr (449.43 kJ/hr)
dissipation
Voltage
100 - 120 / 200 - 240 VAC, rated
DC Voltage
650W DC: -36 VDC to -72 VDC
Frequency
50/60 Hz
UL 60950-1; EN 60825-1 Safety of Laser Products-Part 1; EN 60825-2 Safety of
Laser Products-Part 2; IEC 60950-1; CAN/CSA-C22.2 No. 60950-1; Anatel; ULAR;
GOST; EN 60950-1/A11; FDA 21 CFR Subchapter J; NOM; ROHS Compliance
VCCI Class A; EN 55022 Class A; ICES-003 Class A; ANSI C63.4 2003; AS/NZS
CISPR22 Class A; EN 61000-3-2:2006; EN 61000-3-3:1995 +A1:2001+A2:2005;
EMC Directive 2004/108/EC; FCC (CFR 47, Part 15) Class A
Generic
ETSI EN 300 386 V1.3.3
EN
EN 55024:1998+ A1:2001 + A2:2003
ESD
EN 61000-4-2; IEC 61000-4-2
Radiated
EN 61000-4-3; IEC 61000-4-3
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 36
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
Management
Notes
EFT/Burst
EN 61000-4-4; IEC 61000-4-4
Surge
EN 61000-4-5; IEC 61000-4-5
Conducted
EN 61000-4-6; IEC 61000-4-6
Power frequency
IEC 61000-4-8; EN 61000-4-8
magnetic field
Voltage dips and
EN 61000-4-11; IEC 61000-4-11
interruptions
Harmonics
EN 61000-3-2, IEC 61000-3-2
Flicker
EN 61000-3-3, IEC 61000-3-3
IMC - Intelligent Management Center; command-line interface; Web browser; SNMP
Manager; Telnet; HTTPS; RMON1; FTP
The customer must order a power supply, as the device does not come with a PSU.
At least one JC680A or JC681A is required.
Services
Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services
for details on the service-level descriptions and product numbers. For details about services and
response times in your area, please contact your local Hewlett Packard Enterprise sales office.
Standards and
protocols
(applies to all
products in series)
General protocols
IEEE 802.1ag Service Layer OAM
IEEE 802.1D MAC Bridges
IEEE 802.1p Priority
IEEE 802.1Q VLANs
IEEE 802.1s (MSTP)
IEEE 802.1v VLAN classification by
Protocol and Port
IEEE 802.1w Rapid Reconfiguration of
Spanning Tree
IEEE 802.1X PAE
IEEE 802.3ad Link Aggregation Control
Protocol (LACP)
IEEE 802.3ae 10-Gigabit Ethernet
IEEE 802.3af Power over Ethernet
IEEE 802.3at
IEEE 802.3x Flow Control
RFC 768 UDP
RFC 792 ICMP
RFC 793 TCP
RFC 826 ARP
RFC 854 TELNET
RFC 925 Multi-LAN Address Resolution
RFC 951 BOOTP
RFC 1058 RIPv1
RFC 1350 TFTP Protocol (revision 2)
RFC 1519 CIDR
RFC 1542 BOOTP Extensions
RFC 1812 IPv4 Routing
RFC 2131 DHCP
RFC 2236 IGMP Snooping
RFC 4022 MIB for TCP
RFC 4251 SSHv6 Architecture
RFC 4252 SSHv6 Authentication
RFC 4253 SSHv6 Transport Layer
RFC 4254 SSHv6 Connection
RFC 4293 MIB for IP
RFC 4419 Key Exchange for SSH
RFC 4443 ICMPv6
RFC 4541 IGMP & MLD Snooping Switch
RFC 4861 IPv6 Neighbor Discovery
RFC 4862 IPv6 Stateless Address Autoconfiguration
MIBs
IEEE 8021-PAE-MIB
IEEE 8023-LAG-MIB
RFC 1213 MIB II
RFC 1493 Bridge MIB
RFC 1657 BGP-4 MIB
RFC 1724 RIPv2 MIB
RFC 1850 OSPFv2 MIB
RFC 2011 SNMPv2 MIB for IP
RFC 2013 SNMPv2 MIB for UDP
RFC 2233 Interface MIB
RFC 2273 SNMP-NOTIFICATION-MIB
RFC 2452 IPV6-TCP-MIB
RFC 2454 IPV6-UDP-MIB
RFC 2465 IPv6 MIB
RFC 2466 ICMPv6 MIB
RFC 2571 SNMP Framework MIB
RFC 2572 SNMP-MPD MIB
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 37
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
RFC 2370 OSPF Opaque LSA Option
RFC 2385 TCP MD5 Authentication for
BGPv4
RFC 2453 RIPv2
RFC 2475 Architecture for Differentiated
Services
RFC 2597 Assured Forwarding PHB
Group
RFC 3046 DHCP Relay Agent Information
Option
RFC 3209 RSVP-TE Extensions to RSVP
for LSP Tunnels
RFC 3576 Ext to RADIUS (CoA only)
RFC 3584 Coexistence between Version
1 and Version 2 of the Internet-standard
Network Management Framework
RFC 3623 Graceful OSPF Restart
RFC 3768 VRRP
RFC 4090 Fast Reroute Extensions to
RSVP-TE for LSP Tunnels
RFC 4291 IP Version 6 Addressing
Architecture
RFC 4675 RADIUS VLAN & Priority
RFC 4762 Virtual Private LAN Service
(VPLS) Using Label Distribution Protocol
(LDP) Signaling
802.1r - GARP Proprietary Attribute
Registration Protocol (GPRP)
IP multicast
RFC 2934 Protocol Independent Multicast
MIB for IPv4
RFC 3376 IGMPv3 (host joins only)
RFC 3618 Multicast Source Discovery
Protocol (MSDP)
RFC 3973 Draft 2 PIM Dense Mode
RFC 4601 PIM Sparse Mode
IPv6
RFC 2080 RIPng for IPv6
RFC 2460 IPv6 Specification
RFC 2710 Multicast Listener Discovery
(MLD) for
IPv6
RFC 2740 OSPFv3 for IPv6
RFC 2925 Remote Operations MIB (Ping
only)
RFC 3019 MLDv1 MIB
RFC 3162 RADIUS and IPv6
RFC 3315 DHCPv6 (client and relay)
RFC 3315 DHCPv6 (client only)
RFC 2573 SNMP-Notification MIB
RFC 2618 RADIUS Client MIB
RFC 2620 RADIUS Accounting MIB
RFC 2665 Ethernet-Like-MIB
RFC 2674 802.1p and IEEE 802.1Q
Bridge MIB
RFC 2688 MAU-MIB
RFC 2787 VRRP MIB
RFC 2819 RMON MIB
RFC 2925 Ping MIB
RFC 3414 SNMP-User based-SM MIB
RFC 3415 SNMP-View based-ACM MIB
RFC 3418 MIB for SNMPv3
RFC 3621 Power Ethernet MIB
RFC 3826 AES for SNMP's USM MIB
RFC 4133 Entity MIB (Version 3)
LLDP-EXT-DOT1-MIB
LLDP-EXT-DOT3-MIB
LLDP-MIB
Network management
IEEE 802.1AB Link Layer Discovery
Protocol (LLDP)
RFC 2819 Four groups of RMON: 1
(statistics), 2
(history), 3 (alarm) and 9 (events)
RFC 3176 sFlow
ANSI/TIA-1057 LLDP Media Endpoint
Discovery
(LLDP-MED)
SNMPv1/v2c/v3
OSPF
RFC 2328 OSPFv2
RFC 3101 OSPF NSSA
Security
IEEE 802.1X Port Based Network Access
Control
RFC 1492 TACACS+
RFC 2865 RADIUS (client only)
RFC 2866 RADIUS Accounting
Access Control Lists (ACLs)
Secure Sockets Layer (SSL)
SSHv2 Secure Shell
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 38
QuickSpecs
HPE FlexFabric 5800 Switch Series
Technical Specifications
RFC 3810 MLDv2 (host joins only)
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 39
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessories
HPE FlexFabric 5800 Switch Series accessories
Transceivers
HPE X125 1G SFP LC LH40 1310nm Transceiver
HPE X120 1G SFP LC LH40 1550nm Transceiver
HPE X125 1G SFP LC LH70 Transceiver
HPE X120 1G SFP LC SX Transceiver
HPE X120 1G SFP LC LX Transceiver
HPE X120 1G SFP RJ45 T Transceiver
HPE X115 100M SFP LC BX 10-U Transceiver
HPE X115 100M SFP LC BX 10-D Transceiver
HPE X115 100M SFP LC FX Transceiver
HPE X110 100M SFP LC LX Transceiver
HPE X130 10G SFP+ LC SR Transceiver
HPE X130 10G SFP+ LC LRM Transceiver
HPE X130 10G SFP+ LC LR Transceiver
HPE X130 10G SFP+ LC ER 40km Transceiver
HPE FlexNetwork X240 10G SFP+ to SFP+ 0.65m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 1.2m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 3m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ to SFP+ 5m Direct Attach Copper Cable
HPE FlexNetwork X240 10G SFP+ SFP+ 7m Direct Attach Copper Cable
JD061A
JD062A
JD063B
JD118B
JD119B
JD089B
JD100A
JD101A
JD102B
JD120B
JD092B
JD093B
JD094B
JG234A
JD095C
JD096C
JD097C
JG081C
JC784C
Cables
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 1m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 2m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 5m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 15m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 30m Cable
HPE Premier Flex LC/LC Multi-mode OM4 2 fiber 50m Cable
QK732A
QK733A
QK734A
QK735A
QK736A
QK737A
Power Supply
HPE RPS 800 Redundant Power Supply
HPE RPS1600 Redundant Power System
HPE RPS1600 1600W AC Power Supply
JD183A
JG136A
JG137A
HPE FlexFabric 5800 24G PoE+ Switch (JC099B )
HPE 5800 4-port 10GbE SFP+ Module
HPE 5800 2-port 10GbE SFP+ Module
HPE 5800 16-port Gig-T Module
HPE 5800 16-port SFP Module
HPE 5800 1RU Spare Fan Assembly
JC091A
JC092B
JC094A
JC095A
JC098A
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 40
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessories
HPE FlexFabric 5800 24G Switch (JC100B)
HPE 5800 4-port 10GbE SFP+ Module
HPE 5800 2-port 10GbE SFP+ Module
HPE 5800 16-port Gig-T Module
HPE 5800 16-port SFP Module
HPE 5800 1RU Spare Fan Assembly
JC091A
JC092B
JC094A
JC095A
JC098A
HPE FlexFabric 5800 48G POE+ 2-slot Switch (JC101B)
HPE 5800 4-port 10GbE SFP+ Module
HPE 5800 2-port 10GbE SFP+ Module
HPE 5800 16-port Gig-T Module
HPE 5800 16-port SFP Module
HPE 5800 300W AC Power Supply
HPE 5800 750W AC Power Supply
HPE 5800 300W DC Power Supply
HPE 5800 PoE Module
HPE 5800 2RU Spare Fan Assembly
JC091A
JC092B
JC094A
JC095A
JC087A
JC089A
JC090A
JC097B
JC096A
HPE FlexFabric 5820X 24XG SFP+ Switch (JC103B)
HPE 5800 4-port 10GbE SFP+ Module
HPE 5800 2-port 10GbE SFP+ Module
HPE 5800 16-port Gig-T Module
HPE 5800 16-port SFP Module
HPE FlexNetwork 5500 150WDC Power Supply
HPE X361 150W 100-240VAC to 12VDC Power Supply
HPE X361 150W 48-60VDC to 12VDC Power Supply
HPE 5800 1RU Spare Fan Assembly
JC091A
JC092B
JC094A
JC095A
JD366A
JD362B
JD366B
JC098A
HPE FlexFabric 5800 48G PoE+ 1-slot Switch (JC104B)
HPE 5800 4-port 10GbE SFP+ Module
HPE 5800 2-port 10GbE SFP+ Module
HPE 5800 16-port Gig-T Module
HPE 5800 16-port SFP Module
HPE 5800 1RU Spare Fan Assembly
JC091A
JC092B
JC094A
JC095A
JC098A
HPE FlexFabric 5800 48G 1-slot Switch (JC105B)
HPE 5800 4-port 10GbE SFP+ Module
HPE 5800 2-port 10GbE SFP+ Module
HPE 5800 16-port Gig-T Module
HPE 5800 16-port SFP Module
HPE 5800 1RU Spare Fan Assembly
JC091A
JC092B
JC094A
JC095A
JC098A
HPE FlexFabric 5800AF 48G Switch (JG225B)
HPE 58x0AF 650W AC Power Supply
HPE 58x0AF 650W DC Power Supply
JC680A
JC681A
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 41
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessories
HPE 58x0AF Back (Power Side) to Front (Port Side) Airflow Fan Tray
HPE 58x0AF Front (Port Side) to Back (Power Side) Airflow Fan Tray
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
JC682A
JC683A
Page 42
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
NOTE: Details are not available for all accessories. The following specifications were available at the time
of publication.
HPE X125 1G SFP LC
LH40 1310nm
Transceiver (JD061A)
A small form-factor
pluggable SFP Gigabit
LH40 transceiver that
provides a full duplex
Gigabit solution up to
40km on a single-mode
fiber.
Ports
Connectivity
Physical
characteristics
Electrical
characteristics
Cabling
1 LC 1000Base-LH port (no IEEE standard exists for 1550 nm
optics)
Connector type
LC
Wavelength
1310 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x
1.52 x 1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption 0.8 W
typical
Power consumption 1.0 W
maximum
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
Services
HPE X120 1G SFP LC
LH40 1550nm
Transceiver (JD062A)
A small form-factor
pluggable (SFP) Gigabit
LH40 transceiver that
provides a full-duplex
Gigabit solution up to 40
km on a single mode
fiber.
Ports
Connectivity
Physical
characteristics
Electrical
characteristics
Cabling
40km distance
Fiber type
Single Mode
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm
optics)
Connector type
LC
Wavelength
1550 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x
1.52 x 1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption 0.8 W
typical
Power consumption 1.0 W
maximum
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 43
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
Services
HPE X125 1G SFP LC
LH70 Transceiver
(JD063B)
Ports
Connectivity
A small form-factor
pluggable (SFP) Gigabit Physical
LH70 transceiver that
characteristics
provides a full-duplex
Gigabit solution up to
70km on a single-mode
fiber.
Electrical
characteristics
Cabling
40km distance
Fiber type
Single Mode
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
1 LC 1000BASE-LH port (no IEEE standard exists for 1550 nm
optics)
Connector type
LC
Wavelength
1550 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x
1.52 x 1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption 0.8 W
typical
Power consumption 1.0 W
maximum
Cable type:
Single-mode fiber optic, complying with ITU-T G.652;
Maximum distance:
70km
Services
Fiber type
Single Mode
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 44
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
HPE X120 1G SFP LC
SX Transceiver
(JD118B)
Ports
Connectivity
A small form-factor
pluggable (SFP) Gigabit
SX transceiver that
provides a full-duplex
Gigabit solution up to
550m on a Multimode
fiber.
Physical
characteristics
Electrical
characteristics
Cabling
Services
HPE X120 1G SFP LC
LX Transceiver
(JD119B)
Ports
Connectivity
A small form-factor
pluggable (SFP) Gigabig
LX transceiver that
provides a full duplex
Gigabit solution up to
550m on MMF or 10Km
on SMF
Physical
characteristics
Electrical
characteristics
Cabling
1 LC 1000BASE-SX port
Connector type
LC
Wavelength
850 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x
1.52 x 1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption 0.8 W
typical
Power consumption 1.0 W
maximum
Maximum distance:
FDDI Grade distance = 220m
OM1 = 275m
OM2 = 500m
OM3 = Not Specified by standard
Cable length
up to 550m
Fiber type
Multi Mode
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
1 SFP 1000BASE-LX port (IEEE 802.3z Type 1000BASE-LX)
Connector type
LC
Wavelength
1300 nm
Dimensions
2.17(d) x 0.6(w) x 0.46(h) in. (5.51 x
1.52 x 1.17 cm)
Full configuration
0.04 lb. (0.02 kg)
weight
Power consumption 0.8 W
typical
Power consumption 1.0 W
maximum
Cable type:
Either single mode or multimode;
Maximum distance:
550m for Multimode
10km for Singlemode
Fiber type
Both
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 45
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
Services
HPE X120 1G SFP RJ45 Ports
T Transceiver (JD089B) Connectivity
A small form factor
pluggable (SFP) Gigabit
1000Base-T transceiver
that provides a full
duplex Gigabit solution
up to 100m on a Cat-5+
cable.
Physical
characteristics
Electrical
characteristics
Cabling
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
1 RJ-45 1000BASE-T port (IEEE 802.3ab Type 1000BASE-T)
Connector type
RJ-45
Dimensions
2.71(d) x 0.54(w) x 0.55(h) in. (6.88 x
1.37 x 1.4 cm)
Full configuration
0.07 lb. (0.03 kg)
weight
Power consumption 0.8 W
typical
Power consumption 1.0 W
maximum
Cable type:
1000BASE-T: Category 5 (5E or better recommended), 100 Ù
differential 4-pair unshielded twisted pair (UTP) or shielded twisted pair
(STP) balanced, complying with IEEE 802.3ab 1000BASE-T;
Maximum distance:
100m
Services
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 46
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
HPE Premier Flex
Notes
LC/LC Multi-mode OM4
2 fiber 1m Cable
(QK732A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
Core Diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
Bandwidth: 3000 MHz-km @ 850nm (Laser)
Jacket Color: Blue
Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH)
thermoplastic
Boot Color: White
Outer Jacket Print: HPE PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m
added for lengths >30m
Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Services
HPE Premier Flex
Notes
LC/LC Multi-mode OM4
2 fiber 2m Cable
(QK733A)
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
Bandwidth: 3000 MHz-km @ 850nm (Laser)
Jacket Color: Blue
Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH)
thermoplastic
Boot Color: White
Outer Jacket Print: HPE PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m
added for lengths >30m
Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Services
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 47
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
HPE Premier Flex
Notes
LC/LC Multi-mode OM4
2 fiber 5m Cable
(QK734A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
Bandwidth: 3000 MHz-km @ 850nm (Laser)
Jacket Color: Blue
Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH)
thermoplastic
Boot Color: White
Outer Jacket Print: HPE PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m
added for lengths >30m
Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Services
HPE Premier Flex
Notes
LC/LC Multi-mode OM4
2 fiber 15m Cable
(QK735A)
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
Bandwidth: 3000 MHz-km @ 850nm (Laser)
Jacket Color: Blue
Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH)
thermoplastic
Boot Color: White
Outer Jacket Print: HPE PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m
added for lengths >30m
Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Services
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 48
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
HPE Premier Flex
Notes
LC/LC Multi-mode OM4
2 fiber 30m Cable
(QK736A)
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
Bandwidth: 3000 MHz-km @ 850nm (Laser)
Jacket Color: Blue
Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH)
thermoplastic
Boot Color: White
Outer Jacket Print: HPE PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m
added for lengths >30m
Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Services
HPE Premier Flex
Notes
LC/LC Multi-mode OM4
2 fiber 50m Cable
(QK737A)
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
Cable Specs: Graded-index, "bendable" fiber optic multimode OM3+
50/125um duplex cable and Ethernet assembly with LC duplex
connectors on each end.
Core diameter: 50um ±3um, Cladding diameter: 125um ±2um; Coating
diameter: 245 ± 10um
Bandwidth: 3000 MHz-km @ 850nm (Laser)
Jacket Color: Blue
Jacket Material: Riser Grade - Low Smoke Zero Halogen (LSZH)
thermoplastic
Boot Color: White
Outer Jacket Print: HPE PremierFlex OM3+ Fiber Optic Cable,
50/125um, Type OFNR (UL), LSZH, cUL, OFN FT4, ROHS. Cable also
has a longitudinal white stripe that runs the entire length of the cable.
Insertion Loss: Less than 0.5dB @ 850nm with LED source, 0.003dB/m
added for lengths >30m
Maximum Cable Attenuation: 3.0 dB/km @ 850nm, 1.0 dB/km @
1310nm @ 23°C as tested in accordance with EIA 455-45
Services
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please
contact your local Hewlett Packard Enterprise sales office.
HPE RPS1600
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 49
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
Ports
Redundant Power
System (JG136A)
Physical
characteristics
Environment
Electrical
characteristics
Safety
8 redundant power supply ports
Restrictions: two -56V/25A DC(PoE); six -56V/8A DC(non-PoE)
Dimensions
15.63(d) x 17.32(w) x 1.74(h) in. (39.7
x 44 x 4.42 cm)
Weight
14.11 lb. (6.4 kg)
Full configuration
16.75 lb. (7.6 kg)
weight
Operating temperature 14°F to 122°F (-10°C to 50°C)
Operating relative
5% to 95%
humidity
Nonoperating/Storage -40°F to 158°F (-40°C to 70°C)
temperature
Nonoperating/Storage 5% to 95%
relative humidity
Altitude
up to 13,123 ft. (4 km)
Acoustic
Pressure: 53 dB; ISO 7779, ISO 9296
Voltage
100-120/200-240 VAC
Current
30/60 A
Idle power
38 W
Maximum power rating 3550 W
RPS power
3200 W
PoE power
2800 W
RPS
-55 V
PoE
-55 V
Frequency
50/60 Hz
Notes
Idle power is the actual power
consumption of the device with no
ports connected.
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers
provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports
plugged in, and all modules
populated.
With one RPS1600 Power Supply,
the PRS1600 Redundant Power
System can provide 1600W power
output; With two PRS1600 Power
Supplies, the output power is 3200W.
CE Labeled; UL 60950-1; IEC 60950-1; ICES-003; FCC Part 15, Subpart
B; EU RoHS Compliant; EN 60950-1/A11; C-Tick; VCCI Class A; ROHS
Compliance; EN 300386
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 50
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
Services
HPE RPS1600 1600W Physical
AC Power Supply
characteristics
(JG137A)
Environment
Electrical
characteristics
Services
Standards and
protocols
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please contact
your local Hewlett Packard Enterprise sales office.
Dimensions
Weight
Operating temperature
Operating relative
humidity
Nonoperating/Storage
temperature
Nonoperating/Storage
relative humidity
Voltage
Current
Maximum power rating
Frequency
Notes
8.19(d) x 4.96(w) x 1.63(h) in. (20.8 x
12.6 x 4.15 cm)
3.02 lb. (1.37 kg)
14°F to 122°F (-10°C to 50°C)
5% to 95%
-40°F to 158°F (-40°C to 70°C)
5% to 95%
100-120/200-240 VAC
15/30 A
1600 W
50/60 Hz
Maximum power rating and maximum
heat dissipation are the worst-case
theoretical maximum numbers
provided for planning the
infrastructure with fully loaded PoE (if
equipped), 100% traffic, all ports
plugged in, and all modules
populated.
Refer to the Hewlett Packard Enterprise website at
http://www.hpe.com/networking/services for details on the
service-level descriptions and product numbers. For details
about services and response times in your area, please contact
your local Hewlett Packard Enterprise sales office.
IPv6
RFC 1981 IPv6 Path MTU Discovery
RFC 2460 IPv6 Specification
RFC 2465 Management Information Base
for IP
Version 6: Textual Conventions and
General
Group(partially support, only "IPv6
Interface
Statistics table")
RFC 2405 The ESP DES-CBC Cipher
Algorithm With
Explicit IV
RFC 2406 IP Encapsulating Security
Payload (ESP)
RFC 2410 The NULL Encryption
Algorithm and Its
Use With IPsec
RFC 2411 IP Security Document
Roadmap
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 51
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
RFC 3484 Default Address Selection for
IPv6
RFC 3513 IPv6 Addressing Architecture
RFC 3587 IPv6 Global Unicast Address
Format
RFC 4007 IPv6 Scoped Address
Architecture
RFC 4862 IPv6 Stateless Address Autoconfiguration
Security
RFC 1321 The MD5 Message-Digest
Algorithm
RFC 1334 PPP Authentication Protocols
(PAP)
RFC 1994 PPP Challenge Handshake
Authentication
Protocol (CHAP)
RFC 2104 Keyed-Hashing for Message
Authentication
RFC 2138 RADIUS Authentication
RFC 2618 RADIUS Authentication Client
MIB
RFC 2620 RADIUS Accounting Client
MIB
RFC 2716 PPP EAP TLS Authentication
Protocol
RFC 2865 RADIUS Authentication
RFC 2866 RADIUS Accounting
RFC 2867 RADIUS Accounting
Modifications for
Tunnel Protocol Support
RFC 2868 RADIUS Attributes for Tunnel
Protocol
Support
RFC 2869 RADIUS Extensions
draft-grant-tacacs-02 (TACACS)
RFC 2451 The ESP CBC-Mode Cipher
Algorithms
RFC 2473 Generic Packet Tunneling in
IPv6
Specification
RFC 2529 Transmission of IPv6 over IPv4
Domains
without Explicit Tunnels
RFC 2661 Layer Two Tunneling Protocol
"L2TP"
RFC 2784 Generic Routing Encapsulation
(GRE)
RFC 2868 RADIUS Attributes for Tunnel
Protocol
Support
RFC 2893 Transition Mechanisms for
IPv6 Hosts
and Routers
RFC 3602 The AES-CBC Cipher
Algorithm and Its
Use with IPsec
RFC 4214 Intra-Site Automatic Tunnel
Addressing
Protocol (ISATAP)
IKEv1
RFC 2407 The Internet IP Security
Domain of
Interpretation for ISAKMP
RFC 2408 Internet Security Association
and Key
Management Protocol (ISAKMP).
RFC 2409 The Internet Key Exchange
(IKE)
RFC 2412 The OAKLEY Key
Determination Protocol
RFC 3526 More Modular Exponential
(MODP)
Diffie-Hellman groups for Internet Key
VPN
RFC 1701 Generic Routing Encapsulation Exchange
(IKE)
(GRE)
RFC 1702 Generic Routing Encapsulation RFC 3706 A Traffic-Based Method of
Detecting
over IPv4
Dead Internet Key Exchange (IKE) Peers
networks.
RFC 1828 IP Authentication using Keyed
PKI
MD5
RFC 1829 The ESP DES-CBC Transform RFC 2510 Internet X.509 Public Key
Infrastructure
RFC 1853 IP in IP Tunneling
Certificate Management Protocols
RFC 2085 HMAC-MD5 IP Authentication
RFC 2511 Internet X.509 Certificate
with
Request
Replay Prevention
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 52
QuickSpecs
HPE FlexFabric 5800 Switch Series
Accessory Product Details
RFC 2401 Security Architecture for the
Internet
Protocol
RFC 2402 IP Authentication Header
RFC 2403 The Use of HMAC-MD5-96
within ESP
and AH
RFC 2404 The Use of HMAC-SHA-1-96
within ESP
and AH
Message Format
RFC 3279 Algorithms and Identifiers for
the Internet
X.509 Public Key Infrastructure Certificate
and
Certificate Revocation List (CRL) Profile
RFC 3280 Internet X.509 Public Key
Infrastructure
Certificate and Certificate Revocation List
(CRL)
Profile
draft-nourse-scep-06:
PKCS#1
PKCS#10
PKCS#12
PKCS#7
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 53
QuickSpecs
HPE FlexFabric 5800 Switch Series
Summary of Changes
Date
18-Apr-2017
Version History
From Version 36 to
37
Action
Added
03-Oct-2016
From Version 35 to
36
From Version 34 to
35
From Version 33 to
34
Added
Changed
Changed
From Version 32 to
33
From Version 31 to
32
From Version 30 to
31
From Version 29 to
30
From Version 28 to
29
Changed
Product description updated. Document name
changed to HPE FlexFabric 5800 Switch
Series.
SKUs descriptions updated on the document
Changed
Overview and Technical Specifications updated
Added
Added new DC power supply: JH336A
Changed
Changed
Images changed to real photos.
Configuration menu updated.
SKUs deleted from Transceivers: JD098B,
JD099B
A to B Product Roll on the Switch Series ,
Technical Specifications updated
Accessories Section updated
Warranty and support updated
Changed
Switch Options were revised in Configuration.
Changed
Notes section for Box Level Integration CTO
Models were revised in Configuration.
Transceivers and Modules were revised.
19-Aug-2016
06-June-2016
22-Apr-2016
01-Dec-2015
12-Oct-2015
12-Jun-2015
20- Apr-2015
Changed
Deleted
Changed
01-Dec-2014
10-Jun-2014
15-Apr-2014
19-Mar-2014
16-Jan-2014
17-Dec-2013
11-Nov-2013
15-Oct-2013
19-Aug-2013
05-Jul-2013
27-Jun-2013
From Version 27 to
28
From Version 26 to
27
From Version 25 to
26
From Version 24 to
25
From Version 23 to
24
From Version 21 to
23
From Version 19 to
21
From Version 18 to
19
From Version 17 to
18
From Version 16 to
17
From Version 15 to
16
Changed
Removed
Description of Change:
Transceivers added on the Configuration
section: JH693A; JH694A; JH695A; JL437A;
JL438A; JL439A
SKUs added: JD362B, JD366B
Overview and Technical Specifications updated
Minor changes made on Configuration section
Changed
HPE X240 10G SFP+ 7m DAC Cable was
removed from Configuration.
Configuration was revised and Configuration AF Models was removed
Configuration - AF Models notes and
transceivers were revised.
Configuration was revised.
Changed
Configuration was revised.
Added
Accessories: Added two options.
Changed
Features and benefits and Standards and
protocols were revised
HPE 5800 Access Controller Modules for 64256 and 32-64 Access Points were removed
Changed
Changed
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 54
QuickSpecs
HPE FlexFabric 5800 Switch Series
Summary of Changes
10-Jun-2013
From Version 14 to
15
Changed
24-Apr-2013
From Version 13 to
14
From Version 12 to
13
From Version 11 to
12
From Version 10 to
11
gust 20, 2012From Version 9 to
10
From Version 8 to
9
Added
Configuration Rules was revised throughout
Configuration and Configuration - AF Models
was added.
Overview: Added Images.
Changed
Updated the Configuration section.
Added
Overview: Added Build to Order section to the
Features and benefits section.
Updated the Features and Benefits,
Introduction and Accessories sections.
Updated Accessories and Features and
Benefits.
From Version 7 to
8
From Version 6 to
7
From Version 4 to
6
From Version 3 to
4
From Version 2 to
3
From Version 1 to
2
Changed
10-Apr-2013
25-Mar-2013
24-Aug-2012
20-Aug-2012
14-May-2012
20-Apr-2012
16-Nov-2011
26-Sep-2011
24-May-2011
17-Mar-2011
01-Feb-2011
Changed
Changed
Changed
Added
Features and Benefits, Accessories, and the
weight and dimensions for each spec were
revised.
Features and Benefits and Accessories were
revised.
Updated the Connectivity section of Features
and Benefits.
New models were added.
Changed
Accessories were revised.
Changed
Monitors and Diagnostics was revised.
Changed
Models and Accessories were revised.
Changed
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 55
QuickSpecs
HPE FlexFabric 5800 Switch Series
Summary of Changes
Sign up for updates
© Copyright 2017 Hewlett Packard Enterprise Development LP. The information
contained herein is subject to change without notice. The only warranties for Hewlett
Packard Enterprise products and services are set forth in the express warranty
statements accompanying such products and services. Nothing herein should be
construed as constituting an additional warranty. Hewlett Packard Enterprise shall not
be liable for technical or editorial errors or omissions contained herein.
To learn more, visit: http://www.hpe.com/networking
c04111584 - 13807 - Worldwide - V37 - 18-April-2017
DA - 13807 Worldwide QuickSpecs — Version 37 — 4-18-2017
Page 56