SB-6355 KIT
HDMI HDBaseT 4K/UHD Tx & Rx Extender KIT up to 330 Feet (100M)
(PoH, Dual LAN, 2-way IR, RS-232, SPDIF, Analog Audio, HDMI)
INSTRUCTION MANUAL
™
RECEIVER
TRANSMITTER
IMPORTANT WARRANTY INFORMATION.
If you remove the HDMI screw posts, you must use the provided HDMI Locking
Post replacement screws to keep the internal HDMI jack secure. Removing
the HDMI screws without installing the HDMI Locking Post replacement
screws will void your warranty.
SAFETY INFORMATION
1. To ensure the best results from this product, please read this manual and all other documentation before operating your equipment.
Retain all documentation for future reference.
2. Follow all instructions printed on unit chassis for proper operation.
3. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid.
4. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and
excessive moisture.
5. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth.
6. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience
receptacles, and the point where they exit from the appliance.
7. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced.
8. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the
means of grounding of a piece of equipment is not defeated.
9. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC
voltage is not covered by any warranty.
10. Turn power off and disconnect unit from AC current before making connections.
11. Never hold a power switch in the “ON” position.
12. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use
the unit near stoves, heat registers, radiators, or other heat producing devices.
13. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal
flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky
environment, the unit should be periodically “blown free” of foreign dust and matter.
14. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to
qualified service personnel. There are no user serviceable parts inside.
15. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to
other devices.
16. Do not drive the inputs with a signal level greater than that required to drive equipment to full output.
17. The equipment power cord should be unplugged from the outlet when left unused for a long period of time.
18. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit,
use only the original factory packing.
19. Service Information Equipment should be serviced by qualified service personnel when:
A. The power supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the equipment.
C. The equipment has been exposed to rain.
D. The equipment does not appear to operate normally, or exhibits a marked change in performance.
E. The equipment has been dropped, or the enclosure damaged.
THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.
TABLE OF CONTENTS
HDBaseT™ with PoH 100M EXTENDER Series
Thank you for purchasing the SB-6355x Kit HDBaseT™ with PoH Transmitter and Receiver. You will find this unit easy to
install and highly reliable but it is essential that you read this manual thoroughly before attempting to use the converters.
CONTENTS
SAFETY PRECAUTIONS
INTRODUCTION ..............................................................1
FEATURES & CONTENTS ............................................... 2
SPECIFICATIONS ........................................................... 3
TRANSMITTER PANELS ................................................ 4
RECEIVER PANELS ....................................................... 6
IR PIN CONFIGURATION ............................................... 8
RS-232 PIN CONFIGURATION ...................................... 10
TYPICAL HDBaseT™ APPLICATION ........................... 12
RACK MOUNTS (OPTIONAL) ....................................... 13
WALL MOUNT APPLICATIONS .................................... 15
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
• Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the
PSU if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
INTRODUCTION
Congratulations on your purchase of one of the most innovative
HDMI 1.4a over CAT cable HDBaseT™ Transmitter/Receivers
with POH (Power Over HDBaseT™) on the market today.
The SB-6355T HDBaseT™ Transmitter can transmit HDMI,
Ethernet, PoH with power (48VDC), IR remote input signals to
the Receiver or output to a destination. The RS-232 I/O signal
interfaces to the SB-6355R HDBaseT™ Receiver via a single
LAN (category) cable for a maximum long distance of 328 feet
(100M). The SB-6355T transmitter uses a single UTP/FTP
(category cable) CAT6, CAT6a or CAT7 via a RJ-45 8P8C female
socket (Supports 568a/b). This product provides higher full HD
HDMI 1.4a resolution and supports 480i/p, 720p,1080i/p or
high full 4K2K-30Hz/24Bpp, 4K2K-60Hz/24Bpp with 4:2:0 pixel
format quality that is identical to the high quality full HDMI 1.4
signal source. The SB-6355T is useful for sending 4K2K HDMI
digital video / multi-channel digital audio, IR remote in or out,
Ethernet, RS-232 in-out, KVM (USB2.0) and 48VDC power over
HDBaseT™ (PoH) to the HDBaseT™ Receiver. Signal control via
a single category cable that transmits between the HDBaseT™
Transmitter and HDBaseT™ Receiver.
DISCLAIMERS
The information in this manual has been carefully checked and
is believed to be accurate. We assume no responsibility for any
infringements of patents or other rights of third parties which may
result from its use.
We assume no responsibility for any inaccuracies that may be
contained in this document. We make no commitment to update
or to keep current the information contained in this document.
We reserve the right to make improvements to this document
and/or product at any time and without notice.
COPYRIGHT NOTICE
No part of this document may be reproduced, transmitted,
transcribed, stored in a retrieval system, or any of its part translated
into any language or computer file, in any form or by any means
— electronic, mechanical, magnetic, optical, chemical, manual,
or otherwise — without express written permission and consent.
LOOK A PUPPY!!
NOW READ THIS!!
© Copyright 2017. All Rights Reserved.
Version 2.3 SEPT 2017
6355TR-20150623-002
IMPORTANT WARRANTY INFORMATION.
If you remove the HDMI screw posts, you must
use the provided HDMI Locking Post replacement
screws to keep the internal HDMI jack secure.
Removing the HDMI screws without installing
the HDMI Locking Post replacement screws will
void your warranty.
TRADEMARK ACKNOWLEDGMENTS
All products or service names mentioned in this document may
be trademarks of the companies with which they are associated.
1
FEATURES & CONTENTS
FEATURES
• HDBaseT™ HDMI / DVI extender over CATx (UTP/STP) cable
• Compatible with HDMI 2.0 and HDCP 2.2 compliant
• Supports 5Play™ feature over a single LAN cable. Transmits HDMI, Digital Audio, Bi-directional IR (CIR), 100Base-Tx Ethernet, USB
2.0, RS-232 I/O, SPDIF I/O and 13W PoH
• Application NxK AV matrixes, AV receivers, HD projectors, Single wire TVs and Two-box TVx, KVM (Keyboard, Video, Mouse)
extension, digital signage displays
• HDMI 1080p@60 video V1.4a 3D and Ultra HD 4K2K video, CEC / HDCP compliant
• Supports link speeds up to a max 10.2Gbit/s Video, TMDS format, Deep Color Signal 340MHz, Full HD 1080p@60Hz@24/36/48bit/pixels
• Supports 1080p TV’s at 24/30/60/100/200/240Hz and above as well as Blu-rays at 24FPS
• Supports Digital Audio 7.1 LPCM 192KHz, 24bits, full HD Dolby TrueHD and DTS-HD Master
• Uncompressed HD audio formats
• Transfers Bi-directional infrared control signals together with the HDMI signal
• Supports HDMI CEC between your connected source and display gear
• LED indicators show the POWER/POH/LINK/HDCP status
• Supports external Bi-Directional SPDIF in/out and available for multichannel audio
• Supports stereo audio I/O with PCM 2CH
• Supports Super Audio CD (DSD), CEC commands protocol table
• Extends long distances: 4K2K 30MHz/328 feet (100M) or 1080p 148.5MHz/429 feet (150M)
• Surface mounting bracket included, Other mounting brackets available as a separate option
• Power Input Tx & Rx 48VDC (12.48W), Rx 12VDC (4.8W) with low power consumption (4K load 500mA)
• Power supply universal power switch 50/60Hz,100~240VAC
PACKAGE CONTENTS
Check that you have the following components:
•
•
•
•
•
•
•
•
•
SB-6355x HDBaseT™ Extender console
SB-100 IR Extender Receiver Set
SB-101 IR Extender Transmitter Set
SB-100C IR Extender Receiver Cable (6.5ft (2M))
SB-101C IR Extender Transmitter Cable (6.5ft (2M))
HDMI Locking Post Replacement Screws
1 in Wall mount bracket (Part # WM-1INCH-L80MM)
Users Guide
AC Adaptor:
• Transmitter: 48VDC/1A (universal power switch 50/60Hz,100~240VAC)
• Receiver: 12VDC/1A (universal power switch 50/60Hz,100~240VAC)
• Optional: CAT6 Category cable (328 ft (100M), (P/N: UTP6-100)
2
SPECIFICATIONS
SPECIFICATIONS
• Type of Extender: HDBaseT™ 5Play™ over a single LAN category UTP/STP Cable
• Transmit Signals: HD Video/Audio, 100Base-TX Ethernet, USB (KVM), SPDIF input, SPDIF output, RS-232 i/o, IR input, IR output
and POH (48VDC)
• HDMl Supported: HDMI 1.4 and HDMI 2.0
• HDCP Supported: HDCP 1.X, 2.2 compliant
• Video Supported: Ultra HD (4K2K@30Hz) with YCbCr 4:4:4 and 4K2K@30Hz YCbCr 4:2:0, format up to 1080p@60Hz@48b/pixel
and deep color, 3D
• Video Bandwidth: 10.2Gbps (340MHz)
• Audio I/O Supports: Multi Audio Formats 5.1/7.1, MAT(MLP), Dolby Digital, Dolby TrueHD, Dolby Digital, DTS, DTS-HD Master,
(PCM-2CH)
• Extra S/PDIF I/O: External Bi-Directional SPDIF in/out, Dolby Digital, DTS, Dolby TrueHD, DTS HD-Master Audio, Dolby Pro Logic
Iiz 7.1 & 9.1, and more
• Ethernet Supported: 100bps BaseTx
• KVM Supported: USB 2.0
• IR Infrared Frequency: 38KHz
• Power Over HDBaseT™: 48VDC (100W power using PoH)
• Category Cable Supported: CAT6, CAT6a, CAT7 UTP/STP cable
• Scan Rate Accepted: Supports HDMI full HD resolutions; Frequency 24Hz to 240Hz
• Controls: IR in, IR out, RS-232 I/O, USB (Host), (2) USB (Device) and (2) LAN series interfaces
• Transfer Distance: Up to 10.2GHz/297MHz, 328 feet (100M)/4K2K / Up to 4GHz/148.5MHz, 492 feet (150M)/1080p
• HDMI I/O Connectors: HDMI Type A-SMD 19pin female type
• HDBaseT™ I/O Connectors: HDBaseT™ RJ-45, 8p8c female socket
• PoH Supported: Transmitter (48VDC) to Receiver
• Temperature: Operating Temperature 32°F - 100°F (0°C - 38°C)
• Chassis Material/Color: Metal (think 1mm) / Black
• Dimensions (LxWxH): 8.26 x 4.45 x 1.06 in (210x113x27mm)
• Rack Mount (19 inch): #1U high 19 inch installed Unit / #5U high 19 inch installed for a total of 10 pcs. rack mount
• Weight: Transmitter: 0.70 kgs/1.54 lb / Receiver: 0.58 kgs/1.27 lb
• Safety Approvals: CE, FCC, VCCI & REACH
• Power Consumption:
•Transmitter: 4K Full load
•w/ PoH: Max 300mA (48VDC, 12.48W)
•w/o PoH: Max 400mA (12VDC, 4.8W)
•Receiver: 4K Full load
•w/o PoH: Extra power Max 500mA (12VDC, 6.0W)
• Transmitter Power Supply: Power Input +48VDC, 1A (Universal type 50/60Hz, 100~240VAC)
• Receiver Power Supply: Extra Power Input +12VDC, 1A (Universal type 50/60Hz, 100~240VAC) (Uses extra power when HDBaseT™
Transmitter is w/o PoH)
As product improvements are continuous, specifications are subject to change and without notice.
3
TRANSMITTER FRONT PANEL
FRONT PANEL
1. POWER ON SWITCH: The power switch turns the unit on and off. The LED will illuminate blue to indicate that the switcher is ON and
is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last
configuration will be evoked.
2. POH LED DISPLAY: Power over HDBaseT™ on and off status via LED show out.
3. LINK LED DISPLAY: HDBaseT™ link status LED illuminates blue to indicate that the HDBaseT™ is present on that input.
4. HDCP LED DISPLAY: HDCP status via LED show out.
5. FIRMWARE UPDATE: Firmware update connection via the OD3.5mm jack port.
6. DISTANCE SELECT SWITCH: Select extender distance for 4K2K - 328 ft (100M) or 1080p - 492 ft (150M).
7. USB HOST: Setup the USB port as HOST.
8. USB DEVICE: Setup the USB port as DEVICE.
9. SELECT HOST OR DEVICE SWITCH: Switch to select the USB as HOST or DEVICE.
4
TRANSMITTER BACK PANEL
BACK PANEL
1. POWER INPUT: DC48V, 1A, (Din-4pins Male Plug).
6. HDMI INPUT: HDMI Input signal. If you remove the HDMI screw
2. RS-232 I/O: Sends RS-232 via a HDBaseT™ CATx cable.
7/8. AUDIO INPUT: Extra Stereo Audio Input signal.
3. SPDIF OUTPUT: Receives the SPDIF signal from the HDBaseT™
9/10. LAN I/O: LAN controls I/O.
4. SPDIF INPUT: Sends the SPDIF signal to the HDBaseT™ Receiver
11. IR OUTPUT: Receives Bi-directional IR signal from the HDBaseT™
5. HDBaseT™ OUTPUT (Transmitter): HDBaseT™ sends HDMI the
12. IR INPUT: Sends Bi-directional IR signal to the HDBaseT™
posts, you must use the provided HDMI Locking Post
replacement screws to keep the internal HDMI jack
secure. Removing the HDMI screws without installing
the HDMI Locking Post replacement screws will void
your warranty.
Receiver via a HDBaseT™ CATx cable.
via a HDBaseT™ CATx cable.
Receiver to control the source device.
source signal to the Receiver via a HDBaseT™ RJ45 connector.
Receiver to control the destination device.
5
RECEIVER FRONT PANEL
FRONT PANEL
1. POWER LED DISPLAY: The power switch turns the unit on and off. The LED will illuminate red to indicate that the switcher is ON and
is receiving power. The switcher will remember that last state during a power cycle. When power is removed and resorted, the last
configuration will be evoked.
2. POH LED DISPLAY: Power over HDBaseT™ on and off status via LED show out.
3. LINK LED DISPLAY: HDBaseT™ link status LED illuminates blue to indicate that HDBaseT™ is present on that input.
4. HDCP LED DISPLAY: HDCP status via LED show out.
5. FIRMWARE UPDATE: Firmware update connection via the OD3.5mm jack port.
6. DISTANCE SELECT SWITCH: Select extender distances for 4K2K - 328 ft (100M) or 1080p - 492 ft (150M).
7. USB HOST: Setup the USB port as HOST.
8. USB DEVICE: Setup the USB port as DEVICE.
9. SELECT HOST OR DEVICE SWITCH: Switch to select the USB as HOST or DEVICE.
6
RECEIVER BACK PANEL
BACK PANEL
1. POWER INPUT (Extra): DC12V, 1A, (Male Plug). Extra power
6. HDMI OUTPUT: HDMI Output signal to destination. If you remove
2. RS-232 I/O: Sends RS-232 via a HDBaseT™ CATx cable.
7. AUDIO OUTPUT: Extra Stereo Audio output signal.
3. SPDIF INPUT: Sends the SPDIF signal to the HDBaseT™ Receiver
8./9. LAN I/O: LAN controls I/O.
4. SPDIF OUTPUT: Receives the SPDIF signal from the HDBaseT™
11. IR INPUT: Sends Bi-directional IR signal to the HDBaseT™
5. HDBaseT™ INPUT: (From Transmitter) HDBaseT™ sends the
12. IR OUTPUT: Receives Bi-directional IR signal from the HDBaseT™
offered when Transmitter POH is absent.
the HDMI screw posts, you must use the provided
HDMI Locking Post replacement screws to keep
the internal HDMI jack secure. Removing the HDMI
screws without installing the HDMI Locking Post
replacement screws will void your warranty.
via a HDBaseT™ CATx cable.
Receiver via a HDBaseT™ CATx cable.
Transmitter to control the destination device.
HDMI source signal from the Transmitter via the
HDBaseT™ RJ-45 connector.
Receiver to control the source device.
7
IR PIN CONFIGURATION - TRANSMITTER
IR EXTENDER
REAR
PANEL
IR EXTENDER
PORT - Switcher
TRANSMITTER
1. SB-100
IR 300M
Receiver
IR EXT. In
Cable (3C)
Distance: Max.300M
IR Receiver (SB-100)
IR PN#: SB-XXXX
R oHS /95/E C
IR E XT. in
RS - 232
IR EXT .
DC 12V
3
4
4
R S -232
INP UT
-1
4
UT
3
4
3
IR
UT
-4
S WIT
UT
2
R IX
IN P
I MAT
1
SW
1
HDM
2
C HE
-3
R
3
OFF
-2
UT
IN P
ER
2
P OW
IN P
2
ON
1
1
IN P
IR Rx
ANI-100
SB-100 IR Receiver Set
Control Switch SB-XXXX
SB-100 Maximum Distance ~ 984 feet (300M)
The SB-100 IR Receiver is required when using the port “ALL in” Jack.
2. SB-100C IR 2M Receiver
Switcher IR EXT. In
Cable (2C)
Distance: Max.(2M)
IR Receiver cable 6ft (2M)
IR PN#: SB-XXXX
R oHS /95/E C
IR E XT. in
RS - 232
IR EXT .
INP UT
DC 12V
4
3
UT
4
-2
3
R
-3
C HE
3
IR
UT
-4
IN P
S WIT
UT
R IX
IN P
2
1
SB-100C Maximum Distance ~ 6 feet (2M)
I MAT
2
1
SB-100C IR Receiver Cable
SW
ANI-100
HDM
ER
2
IN P
P OW
UT
2
ON
1
1
IR Rx
IN P
OFF
-1
3
4
4
R S -232
IR Receiver (SB-100C)
Control Switch SB-XXXX
The SB-100C
IR Receiver
will not function
the port
“ALL in”
Jack. active.
Note: When you plug the external
IR extender
into the switcher,
the fronton
panel
IR receiver
remains
IR EXTENDER PACKAGE
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
HOW TO SETUP THE IR EXTENDER RECEIVER COMPONENTS
Pin configuration for IR 984 feet (300M) Extender Receiver such as SB-100 compatible
Tip: Signal
Tip
Ring :VCC
Sleeve: GND
SB-100 IR Receiver Set
Ring
Sleeve
Ring
VCC (Ring)
GND (Sleeve)
Sleeve
Tip (center)
Signal (center)
SB-100 Receiver and SB-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)
Pin configuration for IR Receiver 6 feet (2M) cable such as SB-100C compatible
IR Receiver cable 6ft (2M)
Tip: Signal
Tip
Ring: NC
Sleeve: GND
SB-100C IR Receiver Cable
Ring
Ring
Sleeve
GND (Sleeve)
Sleeve
Tip (center)
Signal (center)
SB-100 Receiver and SB-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.
The frequency range of the IR emitter and receivers is 38khz.
8
IR PIN CONFIGURATION - RECEIVER
IR EXTENDER
REAR
PANEL
IR EXTENDER
PORT - Switcher
RECEIVER
1. SB-100
IR 300M
Receiver
IR EXT. In
Cable (3C)
Distance: Max.300M
IR Receiver (SB-100)
IR PN#: SB-XXXX
R oHS /95/E C
IR E XT. in
RS - 232
IR EXT .
DC 12V
3
4
4
R S -232
INP UT
-1
4
UT
3
4
3
IR
UT
-4
S WIT
UT
2
R IX
IN P
I MAT
1
SW
1
HDM
2
C HE
-3
R
3
OFF
-2
UT
IN P
ER
2
P OW
IN P
2
ON
1
1
IN P
IR Rx
ANI-100
SB-100 IR Receiver Set
Control Switch SB-XXXX
SB-100 Maximum Distance ~ 984 feet (300M)
The SB-100 IR Receiver is required when using the port “ALL in” Jack.
2. SB-100C IR 2M Receiver
Switcher IR EXT. In
Cable (2C)
Distance: Max.(2M)
IR Receiver cable 6ft (2M)
IR PN#: SB-XXXX
R oHS /95/E C
IR E XT. in
RS - 232
IR EXT .
INP UT
DC 12V
4
3
UT
4
-2
3
R
-3
C HE
3
IR
UT
-4
IN P
S WIT
UT
R IX
IN P
2
1
SB-100C Maximum Distance ~ 6 feet (2M)
I MAT
2
1
SB-100C IR Receiver Cable
SW
ANI-100
HDM
ER
2
IN P
P OW
UT
2
ON
1
1
IR Rx
IN P
OFF
-1
3
4
4
R S -232
IR Receiver (SB-100C)
Control Switch SB-XXXX
The SB-100C
IR Receiver
will not function
the port
“ALL in”
Jack. active.
Note: When you plug the external
IR extender
into the switcher,
the fronton
panel
IR receiver
remains
IR EXTENDER PACKAGE
*** When you plug the External IR extender into the switcher, the front panel IR receiver remains active. ***
HOW TO SETUP THE IR EXTENDER RECEIVER COMPONENTS
Pin configuration for IR 984 feet (300M) Extender Receiver such as SB-100 compatible
Tip: Signal
Tip
Ring :VCC
Sleeve: GND
SB-100 IR Receiver Set
Ring
Sleeve
Ring
VCC (Ring)
GND (Sleeve)
Sleeve
Tip (center)
Signal (center)
SB-100 Receiver and SB-101 Transmitter The DISTANCE maximum ~ 984 feet (300M)
Pin configuration for IR Receiver 6 feet (2M) cable such as SB-100C compatible
IR Receiver cable 6ft (2M)
Tip: Signal
Tip
Ring: NC
Sleeve: GND
SB-100C IR Receiver Cable
Ring
Ring
Sleeve
GND (Sleeve)
Sleeve
Tip (center)
Signal (center)
SB-100 Receiver and SB-101C Transmitter The DISTANCE maximum ~ 984 feet (300M)
Note: The External IR jack has voltage on the “Ring” portion of a 3-conductor plug. You must use a 3-conductor plug (aka: stereo plug).
Using a 2-conductor plug will short out the power supply. Always make connections with the switcher power off.
The frequency range of the IR emitter and receivers is 38khz.
9
RS-232 PIN CONFIGURATION - TRANSMITTER
HDBASET™ EXTENDER - TRANSMITTER RS-232 PIN CONFIGURATION
Note: When you plug the external IR extender into the switcher, the front panel IR receiver remains active.
HDBASET™ EXTENDER - TRANSMITTER FIRMWARE UPDATE OD3.5MM JACK PIN CONFIGURATION
10
RS-232 PIN CONFIGURATION - RECEIVER
HDBASET™ EXTENDER - RECEIVER RS-232 PIN CONFIGURATION
Note: When you plug the external IR extender into the switcher, the front panel IR receiver remains active.
HDBASET™ EXTENDER - RECEIVER FIRMWARE UPDATE OD3.5MM JACK PIN CONFIGURATION
11
2. The Total distance 328 feet (100M) via a CATX (CAT5e, CAT6, CAT6a, CAT7) category cable.
Samples Connection:
1. Using HDBaseT™ Transmitter and Receiver to extend the 4K HDMI signals and control bi-directional IR in/out, RS-232 I/O, Ethernet I/O, SPDIF Audio in/out or KVM
(USB2.0 series interface).
INSTALLING DIAGRAM
TYPICAL HDBaseT™ TRANSMITTER/RECEIVER APPLICATION
12
19 INCH RACK MOUNT APPLICATIONS
1U RACK MOUNT (OPTIONAL)
SB-6077: Complete 19 inch 1U rack mount
Install Application: SB-6355T/SB-6355R 19 INCH 4U-01P RACK MOUNT
Parts No.: MEER60770013000
Model No.: #1U-01p-L210MM-COV
SB-6355T/SB-6355R 1U Ear mount pairs
Parts No.: MEER6300ER1102
Application Diagram: #1U 19 inch - (1) Unit (HxL) (27x210mm)
13
19 INCH RACK MOUNT APPLICATIONS
5U RACK MOUNT (OPTIONAL)
SB-6078: Complete 19 inch 5U rack mount
Install Application: SB-6355T/SB-6355R 19 INCH 5U-10P RACK MOUNT
Parts No.: MEER6078001300
Model No.: #5U-10p-L210MM-COV
SB-6355T/SB-6355R 5U Ear mount pairs
Parts No.: MEER6078ER11000
Model No.: #5U-10p-L210MM-EAR
SB-6355T/SB-6355R 5U Rack mount ear pairs
Parts No.: MEER1616HA10000
Application Diagram: #5U 19 inch - (10) Unit (HxL) (27x210mm)
14
WALL MOUNT APPLICATIONS
WALL MOUNT: (OPTIONAL)
SB-6355T/SB-6355R: Wall mount accessories
Model No.: #WM-1INCH-L210MM
Install Application: SB-6355T/SB-6355R WALL MOUNT
Parts No.: MEER6300ER11000
Application Diagram: #1 inch HIGH - (1) Unit (HxL) (27x210mm)
15
THIS PAGE IS INTENTIONALLY LEFT BLANK.
LIMITED WARRANTY
PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED
BY, THROUGH OR UNDER SHINYBOWUSA, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your
agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to SHINYBOWUSA,
Inc. at the return address set forth on the Product’s packing label at your expense. SHINYBOWUSA, Inc. may modify these Terms and Conditions at anytime,
without notice to you.
RESTRICTIONS ON USE OF THE PRODUCT
It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product.
You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any
warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be
borne by you and you agree to indemnify and hold harmless SHINYBOWUSA, Inc. from and against any such damage.
The Product is protected by certain intellectual property rights owned by or licensed to SHINYBOWUSA. Any intellectual property rights pertaining to the Product
are licensed to you by SHINYBOWUSA, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “SHINYBOWUSA”) for your
personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product.
The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by SHINYBOWUSA for your personal use only.
SHINYBOWUSA does not transfer either the title or the intellectual property rights to the Product and SHINYBOWUSA retains full and complete title to the
intellectual property rights therein. All trademarks and logos are owned by SHINYBOWUSA or its licensors and providers of the Product, and you may not copy or
use them in any manner without the prior written consent of SHINYBOWUSA, which consent may be withheld at the sole discretion of SHINYBOWUSA.
The functionality and usability of the Product is controlled by SHINYBOWUSA, Inc. from its offices within the State of Texas, United States of America. SHINYBOWUSA
makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided
with respect thereto. You are advised that the Product may be subject to U.S. export controls.
DISCLAIMERS AND LIMITATION OF LIABILITY
SHINYBOWUSA may change or modify the Product at any time, from time to time.
THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. SHINYBOWUSA DOES NOT WARRANT
OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY,
OR OTHERWISE.
SHINYBOWUSA has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should
not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical
inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product.
TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, SHINYBOWUSA DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
SHINYBOWUSA DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT.
SHINYBOWUSA DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO
THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS.
SHINYBOWUSA WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU
NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT SHINYBOWUSA) ASSUME THE ENTIRE COST
OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING
BY SHINYBOWUSA.
UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL SHINYBOWUSA BE LIABLE FOR ANY SPECIAL OR
CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS,
EVEN IF SHINYBOWUSA OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL
SHINYBOWUSA’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE)
EXCEED THE AMOUNT YOU PAID TO SHINYBOWUSA, IF ANY, FOR THE PRODUCT.
END OF DOCUMENT
17
122 Rose Ln. Suite 303 |
Frisco, Texas 75034
1-877-SHINY-USA
1-877-744-6987
1-972-377-2508
sales@shinybowusa.com
www.shinybowusa.com