EPSON EB-435W/430/425W/420 User'

User’s Guide
Notations Used in This Guide
• Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
• General information indications
Attention
a
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
s
Indicates a page where detailed information regarding a topic can be found.
g
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
section of the "Appendices".
s "Glossary" p.129
[Name]
Menu Name
Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Indicates Configuration menu items.
Example:
Select Brightness from Image.
Image - Brightness
Contents
3
Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2
Connecting External Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting a LAN Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installing the Optional Wireless LAN Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Introduction
Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enabling projection from a short distance . . . . . . . . . . . . . . . . . . . . . . . .
Easy writing on a whiteboard or blackboard using the pattern function . . . .
Connecting with a USB cable and projecting (USB Display) . . . . . . . . . . . .
Connecting to a network and projecting images from the computer's screen
.....................................................
Enhanced security functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enlarge and project your files with the Document Camera . . . . . . . . . . . . .
Easy connection to a computer with Quick Wireless . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
7
7
7
7
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
7
7
7
7
7
Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front/Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Remote control operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. 8
. 9
10
11
12
15
15
Preparing the Projector
Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Installation Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Basic Usage
Projecting images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
From Installation to Projection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Automatically Detect Input Signals and Change the Projected Image (Source Search)
... ....... ......... ... ....... ......... ... ....... ..........
Switching to the Target Image Using the Remote Control . . . . . . . . . . . . . . . . . .
Projecting with USB Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
System requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Uninstalling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28
29
30
30
30
31
32
Adjusting Projected Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Correcting Keystone Distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
H/V-Keystone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Quick Corner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Image Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Image Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Horizontal Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correcting the Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . . .
Setting Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the Aspect Ratio of the Projected Image . . . . . . . . . . . . . . . . . . .
Changing methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing the aspect mode (EB-435W/EB-425W only) . . . . . . . . . . . . . . .
Changing the aspect mode (EB-430/EB-420 only) . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
34
34
35
37
37
37
38
38
38
39
40
40
40
41
Connecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Connecting a Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting Image Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting USB Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Connecting a microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
18
19
22
23
Useful Functions
Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . . . . . . . . . . . . . 44
Contents
Freezing the Image (Freeze) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Pointer Function (Pointer) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Enlarging Part of the Image (E-Zoom) . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse)
Saving a User's Logo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Saving User Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
. .. .. .
......
......
. . . . .
. . ... .
......
.
.
.
.
.
.
44
45
46
47
48
50
Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Managing Users (Password Protect) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Kinds of Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting Password Protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Entering the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Restricting Operation (Control Panel Lock) . . . . . . . . . . . . . . . . . . . . . . .
Anti-Theft Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the wire lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
52
52
52
53
54
55
55
Configuration Menu
Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
List of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Configuration Menu Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Image Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Extended Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Network Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Notes on operating the Network menu . . . . . . . . . . . . . . . . . . . . . .
Soft keyboard operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Security menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wired LAN menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mail menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Others menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reset menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
58
59
60
61
63
64
66
67
67
68
68
70
71
72
73
74
Info Menu (Display Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Reset Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Troubleshooting
Using the Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Reading the Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
When the Indicators Provide No Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems Relating to Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No images appear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Moving images are not displayed (only the moving image portion turns black)
...... .. ..... ...... ..... .. ...... ..... ....... ...... ....
Projection stops automatically . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The message "Not supported" is displayed. . . . . . . . . . . . . . . . . . . . . . . . .
The message "No Signal" is displayed. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . .
Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . .
The image is truncated (large) or small, or the aspect is not suitable . . . . . . .
Image colors are not right . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Images appear dark . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Problems when Projection Starts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Other Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . .
No sound can be heard from the microphone . . . . . . . . . . . . . . . . . . . . . .
The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I want to change the language for messages and menus . . . . . . . . . . . . . . .
Mail is not received even if an error occurs with the projector . . . . . . . . . . .
.
.
.
.
.
.
.
.
79
82
83
83
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
84
84
84
84
85
85
86
87
87
88
88
89
89
89
90
90
90
About Event ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Contents
5
Maintenance
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Cleaning the Projector's Surface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Cleaning the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Replacing Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lamp replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to replace the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resetting the lamp hours . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing the Air Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Air filter replacement period . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
How to replace the air filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
96
96
96
99
99
99
99
Appendix
Slideshow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Projecting Without a Computer (Slideshow) . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications for files that can be projected using Slideshow . . . . . . . . . . . . .
Slideshow examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slideshow operating methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting the selected image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Projecting image files in a folder in sequence (Slideshow) . . . . . . . . . . . . . . .
Image file display settings and Slideshow operation settings . . . . . . . . . . . . .
103
103
103
103
105
106
107
Monitoring and Controlling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
About EasyMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing Settings Using a Web Browser (Web Control) . . . . . . . . . . . . . . . . . . .
Projector setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Web Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Displaying the Web Remote screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Mail Notification Function to Report Problems . . . . . . . . . . . . . . . . . .
Reading Error Notification Mail . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Management Using SNMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
108
108
108
109
109
111
111
111
ESC/VP21 Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Command list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cable layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About PJLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
About Crestron RoomView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating a projector from your computer . . . . . . . . . . . . . . . . . . . . . . . . .
®
112
112
112
113
114
114
Optional Accessories and Consumables . . . . . . . . . . . . . . . . . . . . 118
Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . 119
Projection Distance (For EB-430/EB-420) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Projection Distance (For EB-435W/EB-425W) . . . . . . . . . . . . . . . . . . . . . . . . . . 120
Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122
Supported Resolutions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Computer signals (analog RGB) . . . . . . . . . . . . . . . . . . . . . . . . .
Component Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Composite video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input signal from the HDMI port . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
122
122
122
122
122
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Projector General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
About Notations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
General Notice: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
Introduction
This chapter explains the projector's features and the part names.
Projector Features
Projection Functions
Enabling projection from a short distance
You can project large images from a short distance without having to move
the projector away from the screen.
s "Screen Size and Projection Distance" p.119
Easy writing on a whiteboard or blackboard using the pattern
function
You can project ruled lines and grid patterns. This is useful when drawing
diagrams on a whiteboard or blackboard.
7
Enhanced security functions
• Password Protect to restrict and manage users
By setting a password you can restrict who can use the projector.
s "Managing Users (Password Protect)" p.52
• Control Panel Lock restricts button operation on the control panel
You can use this to prevent people changing projector settings without
permission at events, in schools, and so on.
s "Restricting Operation (Control Panel Lock)" p.54
• Equipped with various anti-theft devices
The projector is equipped with the following types of anti-theft security
devices.
• Security slot
• Security cable installation point
s Settings - Pattern p.63
s "Anti-Theft Lock" p.55
Connecting with a USB cable and projecting (USB Display)
By simply connecting a commercially available USB cable, you can project
images from a computer's screen without a computer cable.
Optional Functions
s "Projecting with USB Display" p.30
Enlarge and project your files with the Document Camera
Connecting to a network and projecting images from the
computer's screen
You can connect the projector to a computer on a network and project the
computer's screen using the supplied EasyMP Network Projection
(application software).
sEasyMP Network Projection Operation Guide
You can project paper documents and objects using the optional Document
Camera. Image focus is automatically adjusted using the auto focus
function. You can also enlarge images using digital zoom.
s "Optional Accessories" p.118
Easy connection to a computer with Quick Wireless
By simply connecting the optional Quick Wireless Connection USB Key to
a computer, you can project the computer's screen. (Windows computers
only)
s "Optional Accessories" p.118
Part Names and Functions
8
Name
Front/Top
Function
D Air intake vent
(air filter)
Takes in air to cool the projector internally.
s "Cleaning the Air Filter" p.94
s "Replacing the Air Filter" p.99
E Focus ring
Adjusts the image focus.
s "Correcting the Focus" p.38
F Control panel
Operates the projector.
s "Control Panel" p.11
G Lamp cover
Open when replacing the projector's lamp.
s "Replacing the Lamp" p.96
H Air exhaust vent
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands
near the air exhaust vent, and do not place objects
that may become warped or damaged by heat near
the vent.
Name
Function
A Remote receiver
Receives signals from the remote control.
B Foot adjust lever
Press the foot lever to extend and retract the front foot.
s "Adjusting the Image Position" p.37
C Front adjustable foot
When setup on a surface such as a desk, extend the foot to
adjust the position of the image.
s "Adjusting the Image Position" p.37
I Indicators
Indicates the projector's status.
s "Reading the Indicators" p.79
J Lens cover
Attach the cover when not using the projector to prevent
the lens from getting dirty or being damaged.
Part Names and Functions
9
Name
Rear
Name
Function
A HDMI port
Inputs video signals from HDMI compatible video
equipment and computers. This projector is compatible
with HDCPg.
s "Connecting Equipment" p.18
B Video port
Inputs composite video signals from video sources.
C RS-232C port
When controlling the projector from a computer, connect
it to the computer with an RS-232C cable. This port is for
control use and should not normally be used.
s "ESC/VP21 Commands" p.112
D Monitor Out port
Outputs analog RGB signals input from the Computer1
port to an external monitor. You cannot output signals
input from other ports or component video signals.
E Audio1 port
Inputs audio from equipment connected to the
Computer1 port.
F Audio Out port
Outputs audio from the currently projected image or the
Mic port to an external speaker.
Function
G Mic port
Inputs audio from the microphone.
s "Connecting a microphone" p.23
H Power inlet
Connects the power cable to the projector.
s "From Installation to Projection" p.28
I Security slot
The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
s "Anti-Theft Lock" p.55
J Wireless LAN unit
installation section
Install the optional Wireless LAN unit here. Remove the
stopper when installing.
s "Installing the Optional Wireless LAN Unit" p.26
K Speaker
Outputs audio.
L LAN port
Connects a LAN cable to connect to a network.
M USB(TypeA) port
• Connects a USB memory device or a digital camera, and
projects images as a Slideshow.
s "Projecting Without a Computer (Slideshow)"
p.103
• Connects the optional Document Camera.
N USB(TypeB) port
• Connects the projector to a computer via a
commercially available USB cable, and projects the
images on the computer.
s "Projecting with USB Display" p.30
• Connects the projector to a computer via the
commercially available USB cable to use the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.47
O Computer2 port
Inputs image signals from a computer and component
video signals from other video sources.
P Audio2 port
Inputs audio from equipment connected to the
Computer2 port.
Q Computer1 port
Inputs image signals from a computer and component
video signals from other video sources.
Part Names and Functions
Name
10
Function
R Audio-L/R port
Inputs audio from equipment connected to the S-Video
port or the Video port.
S S-Video port
For S-video signals from video sources.
Base
Name
Function
A Ceiling mount fixing
points (three points)
Attach the optional Ceiling Mount here when suspending
the projector from a ceiling.
s "Installing the Projector" p.17
s "Optional Accessories" p.118
B Wall mount plate
fixing points (five
points)
Attach the optional wall mount plate here when
suspending the projector from a wall.
s "Optional Accessories" p.118
Part Names and Functions
Name
11
Function
C Rear feet
When setup on a surface such as a desk, turn to extend and
retract to adjust the horizontal tilt.
s "Adjusting the Horizontal Tilt" p.37
D Security cable
installation point
Pass a commercially available wire lock through here and
lock it in place.
s "Installing the wire lock" p.55
E Front adjustable foot
When setup on a surface such as a desk, extend the foot to
adjust the position of the image.
s "Adjusting the Image Position" p.37
Control Panel
Name
Function
A [t] button
Turns the projector power on or off.
s "From Installation to Projection" p.28
B [Source Search]
button
Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.29
C [
• When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
• If pressed while projecting analog RGB signals from
Computer1 port or Computer2 port, you can
automatically optimize Tracking, Sync., and Position.
] button
Part Names and Functions
Name
12
Function
D [w][v] button
• Displays the Keystone screen allowing you to correct
keystone distortion in vertical and horizontal
directions.
s "H/V-Keystone" p.34
• If pressed when the Configuration menu or the Help
screen is displayed, these buttons select menu items and
setting values.
s "Using the Configuration Menu" p.57
s "Using the Help" p.78
E [Help] button
Displays and closes the help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.78
F [Esc] button
• Stops the current function.
• If pressed when the Configuration menu is displayed, it
moves to the previous menu level.
s "Using the Configuration Menu" p.57
G [Tele]/[Wide] buttons
• Adjusts the size of the projection screen. Press the [Tele]
button to reduce the size of the projection screen and
press the [Wide] button to increase the size of the
projection screen.
• Corrects keystone distortion in the horizontal direction
when the Keystone screen is displayed.
s "H/V-Keystone" p.34
• If pressed when the Configuration menu or the Help
screen is displayed, these buttons select menu items and
setting values.
s "Using the Configuration Menu" p.57
s "Using the Help" p.78
H [Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.57
Remote Control
Part Names and Functions
Name
13
Function
A [t] button
Turns the projector power on or off.
s "From Installation to Projection" p.28
B [Computer] button
Each time you press the button, the input changes between
images from the Computer1 port and the Computer2
port.
C [Video] button
Each time the button is pressed, the image cycles through
the S-Video, Video, and HDMI ports.
D Numeric buttons
• Enter the Password.
s "Setting Password Protect" p.52
• Use this button to enter numbers in Network settings
from the Configuration menu.
E [Auto] button
If pressed while projecting analog RGB signals from
Computer1 port or Computer2 port, you can
automatically optimize Tracking, Sync., and Position.
F [Aspect] button
Each time the button is pressed, the aspect mode changes.
s "Changing the Aspect Ratio of the Projected Image"
p.40
G [Num] button
Hold down this button and press the numeric buttons to
enter passwords and numbers.
s "Setting Password Protect" p.52
H [Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.57
Name
I [
][
][ ][ ]
button
Function
• When the Configuration menu or Help screen is
displayed, pressing these buttons selects menu items
and setting values.
s "Using the Configuration Menu" p.57
• When projecting a Slideshow, pressing these buttons
displays the previous/next image, rotates the image, and
so on.
s "Slideshow operating methods" p.103
• During Wireless Mouse function, the mouse pointer
moves in the direction of the button that was pushed.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.47
J [User] button
Select any frequently used item from the seven available
Configuration menu items, and assign it to this button. By
pressing the [User] button, the assigned menu item
selection/adjustment screen is displayed, allowing you to
make one-touch settings/adjustments.
s "Settings Menu" p.63
Power Consumption is assigned as the default setting.
K [Page] buttons
[[][]]
Changes pages in files such as PowerPoint files when using
the following projection methods.
• When using the Wireless Mouse function
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.47
• When using USB Display
s "Projecting with USB Display" p.30
• When connecting to a network
When projecting images using Slideshow, pressing these
buttons displays the previous/next image file.
L [A/V Mute] button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.44
Part Names and Functions
Name
14
Function
Name
Function
M [E-Zoom] buttons
[z][x]
Enlarges or reduces the image without changing the
projection size.
s "Enlarging Part of the Image (E-Zoom)" p.46
U [Color Mode] button
Each time the button is pressed, the color mode changes.
s "Selecting the Projection Quality (Selecting Color
Mode)" p.38
N Strap hole
Allows you to attach a commercially available strap to the
remote control.
V [LAN] button
O [Help] button
Displays and closes the help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.78
Changes to the images projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to
that image.
W [USB] button
Each time the button is pressed, it cycles through the
following images:
• USB Display
• Images from the device connected to the USB(TypeA)
port
X [Source Search]
button
Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.29
Y Remote control lightemitting area
Outputs remote control signals.
P [Freeze] button
Pauses or resumes image playback.
s "Freezing the Image (Freeze)" p.44
Q [Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.38
R [Pointer] button
Displays the on-screen pointer.
s "Pointer Function (Pointer)" p.45
S [
• When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
s "Using the Configuration Menu" p.57
• Acts as a mouse's left button when using the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.47
] button
T [Esc] button
• Stops the current function.
• If pressed when the Configuration menu is displayed, it
moves to the previous level.
s "Using the Configuration Menu" p.57
• Acts as a mouse's right button when using the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.47
Part Names and Functions
15
Replacing the remote control batteries
If the remote control becomes unresponsive or inoperable after it has been
used for some time, the batteries may have reached the end of their service
life. When this happens, replace them with new batteries. Obtain two AA
size manganese or alkaline batteries. You cannot use other batteries except
for the AA size manganese or alkaline.
Caution
Check the positions of the (+) and (-) marks inside the battery holder to
ensure the batteries are inserted the correct way.
c
Reattach the battery cover.
Press the battery cover until it clicks into place.
Attention
Make sure you read the following manual before handling the batteries.
s Safety Instructions
a
Remove the battery cover.
While pushing the battery cover catch, lift the cover up.
Remote control operating range
b
Replace the old batteries with new batteries.
Preparing the Projector
This chapter explains how to install the projector and connect projection sources.
Installing the Projector
17
Installation Methods
Warning
The projector supports the following four different projection methods.
Install the projector according to the conditions of the installation location.
• Project images from in front of
the screen. (Front projection)
• Project images from behind a
translucent screen. (Rear projec‐
tion)
• Suspend the projector from a
wall or ceiling and project im‐
ages from in front of a screen.
(Front/Ceiling projection)
• Suspend the projector from the
ceiling and project images from
behind a translucent screen.
(Rear/Ceiling projection)
• A special method of installation is required when suspending the projector
from a wall or ceiling. If it is not installed correctly, it could fall causing an
accident and injury.
• If you use adhesives on the wall mount plate fixing points or the ceiling
mount fixing points to prevent the screws from loosening, or if you use
things such as lubricants or oils on the projector, the projector case may
crack causing it to fall from its mount. This could cause serious injury to
anyone under the mount and could damage the projector.
When installing or adjusting the mount, do not use adhesives to prevent the
screws from loosening and do not use lubricant or oil and so on.
Attention
• Do not use the projector on its side. This may cause malfunctions to occur.
• Do not cover the projector's air intake vent or air exhaust vent. If either of
the vents are covered, the internal temperature could rise and cause a fire.
a
• When installing the projector on a wall or on the ceiling, make sure
you use the correct tools for the installation method.
s "Optional Accessories" p.118
• You can change the setting as follows by pressing down the [A/V
Mute] button on the remote control for about five seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
• Set Rear or Rear/Ceiling from the configuration menu.
s Extended - Projection p.64
Connecting Equipment
18
The port name, location, and connector orientation differ depending on the source being connected.
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
A B When using the supplied computer cable
Connect the computer's display output port to the projector's Computer1 or Computer2 port.
You can output audio from the projector's speaker by connecting the computer's audio output port to the projector's Audio1 or Audio2 port using a commercially available
audio cable.
When
using a commercially available USB cable
C
Connect the computer's USB port to the projector's USB(TypeB) port.
You can send the audio with the projected image.
When using a commercially available HDMI cable
D
Connect the computer's HDMI port to the projector's HDMI port.
You can send the audio with the projected image.
a
You can switch the audio input by using Audio Input.
s Extended - Operation - Audio Input p.64
Connecting Equipment
a
19
You can use the commercially available USB cable to connect the projector to a computer to project images from the computer.This function is called USB
Display.
s "Projecting with USB Display" p.30
Connecting Image Sources
To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.
A
When using a commercially available video cable
B
Connect the video output port on the image source to the projector's Video port using a commercially available video cable.
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available
audio cable.
When using a commercially available S-video cable
Connecting Equipment
20
Connect the video output port on the image source to the projector's S-Video port using a commercially available video cable.
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available
audio cable.
C D When using the optional component video cable
s "Optional Accessories and Consumables" p.118
Connect the component output port on the image source to the projector's Computer1 or Computer2 port.
You can output audio from the projector's speaker by connecting the image source's audio output port to the projector's Audio1 or Audio2 port using a commercially available
audio cable.
When using a commercially available HDMI cable
E
Connect the HDMI port on the image source to the projector's HDMI port using a commercially available HDMI cable.
You can send the audio with the projected image.
a
You can switch the audio input by using Audio Input.
s Extended - Operation - Audio Input p.64
Connecting Equipment
Attention
• If the input source is on when you connect it to the projector, it could cause a malfunction.
• If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.
21
Connecting Equipment
a
22
• If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.
• When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".
Connecting USB Devices
You can connect devices such as USB memory, the optional Document Camera, and USB compatible hard disks and digital cameras.
Using the USB cable supplied with the USB device, connect the USB device to the USB(TypeA) port on the projector.
When the USB device is connected, you can project image files on the USB memory or digital camera using Slideshow.
s "Slideshow" p.103
If the Document Camera is connected while projecting images from another input port, press the [USB] button on the remote control, or the [Source Search]
button on the control panel, to switch to images from the Document Camera.
s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.29
a
While projecting images from a USB device, if you want to connect an audio output device, connect it to the Audio2 port.
Connecting Equipment
23
Attention
•
•
•
•
If you use a USB hub, operation may not be performed correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.
When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.
Connect a digital camera or hard disk to the projector using a USB cable supplied with or specified for use with the device.
Use a USB cable less than 3 m in length. If the cable exceeds 3 m, Slideshow may not function correctly.
Removing USB devices
After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from
the projector.
Connecting a microphone
You can output microphone audio from the projector's speaker by connecting a commercially available dynamic microphone.
a
• Plug-in-power is not supported.
• Adjust Mic Input Level if the microphone audio is difficult to hear, or if it is too loud resulting in a crackling sound.
s Settings - Mic Input Level p.63
• Make the following settings to output audio from a microphone when the projector is turned off.
Set Standby Mode to Communication On. s Extended - Standby Mode p.64
Set Standby Microphone to On. s Extended - Standby Microphone p.64
Connecting Equipment
24
Connecting External Equipment
You can output images and audio by connecting an external monitor or speaker.
A When outputting images to an external monitor
Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.
B When outputting audio to an external speaker
Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.
a
• If you set Standby Mode to Communication On, you can output images to an external monitor even if the projector is in standby mode.
s Extended - Standby Mode p.64
• Only analog RGB signals from the Computer1 port can be output to an external monitor. You cannot output signals input from other ports or component video
signals.
• Setting gauges for functions such as Keystone, Configuration menu, or Help screens are not output to the external monitor.
• When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external
output.
Connecting a LAN Cable
Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN
cable.
Connecting Equipment
a
To prevent malfunctions, use a category 5 shielded LAN cable.
25
Connecting Equipment
Installing the Optional Wireless LAN Unit
a
Remove the stopper fixing screw, and then remove the wireless
LAN unit's stopper.
b
Install the Wireless LAN unit.
c
To avoid losing the wireless LAN unit, secure the stopper using the
stopper fixing screw.
26
Basic Usage
This chapter explains how to project and adjust images.
Projecting images
From Installation to Projection
This section explains the procedure for connecting the projector to a
computer with the computer cable and projecting images.
28
e
f
Turn on the computer.
Change the computer's screen output.
When using a laptop computer, you need to change the screen
output from the computer.
Hold down the Fn key (function key), and press the b key.
a
The method for changing differs depending on the computer
being used. See the documentation supplied with the computer.
If the image is not projected, you can change the projected image using one
of the following methods.
• Press the [Source Search] button on the control panel or the remote
control.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.29
• Press the button for the target port on the remote control.
s "Switching to the Target Image Using the Remote Control" p.30
a
After projecting the image, adjust the image if necessary.
s "Correcting Keystone Distortion" p.34
s "Correcting the Focus" p.38
a
b
c
d
Remove the lens cover.
Connect the projector to an electrical outlet with the power cable.
Connect the projector to the computer with the computer cable.
Turn on the projector.
Projecting images
29
Automatically Detect Input Signals and Change
the Projected Image (Source Search)
Press the [Source Search] button to project images from the port currently
receiving an image.
Because only images from ports receiving an image are projected, you can
quickly project the image you want.
Using Remote Control
Computer1
LAN
Computer2
USB
Using the Control Panel
S-Video
Video
USB Display
HDMI
When two or more image sources are connected, press the [Source Search]
button until the target image is projected.
When your video equipment is connected, start playback before beginning
this operation.
a
The following screen is displayed while no image signals are input.
Projecting images
30
Switching to the Target Image Using the Remote
Control
You can change directly to the target image by pressing the following
buttons on the remote control.
Projecting with USB Display
You can use the commercially available USB cable to connect the projector
to a computer to project images from the computer.
You can send the computer's audio with the projected image.
Remote control
System requirements
For Windows
OS
A Each time the button is pressed, it cycles through the following images:
• Computer1 port
• Computer2 port
B Each time the button is pressed, it cycles through the following images:
• S-Video port
• Video port
• HDMI port
C Changes to the images projected with EasyMP Network Projection. When
projecting using the optional Quick Wireless Connection USB Key, this
button switches to that image.
D Each time the button is pressed, it cycles through the following images:
• USB Display
• Images from the device connected to the USB(TypeA) port
Windows 2000*1
Windows XP*2
Professional 32 bit, Home Edition 32
bit, Tablet PC Edition 32 bit
Windows Vista
Ultimate 32 bit, Enterprise 32 bit,
Business 32 bit, Home Premium 32
bit, Home Basic 32 bit
Windows 7
Ultimate 32/64 bit, Enterprise 32/64
bit, Professional 32/64 bit, Home
Premium 32/64 bit, Home Basic 32
bit, Starter 32 bit
CPU
Mobile Pentium III 1.2 GHz or faster
Recommended: Pentium M 1.6 GHz or faster
Amount of
Memory
256 MB or more
Recommended: 512 MB or more
Hard Disk
Free Space
20 MB or more
Display
Resolution of no less than 640x480 and no higher than
1600x1200.
Display color of 16-bit color or greater
*1 Service Pack 4 only
*2 Except for Service Pack 1
Projecting images
31
Connecting for the first time
For Mac OS
OS
Mac OS X 10.5.1 or later
Mac OS X 10.6.x
CPU
Power PC G4 1GHz or faster
Recommended: Core Duo 1.83GHz or faster
Amount of
Memory
512 MB or more
Hard Disk
Free Space
20 MB or more
Display
Resolution of no less than 640x480 and no higher than
1680x1200.
Display color of 16-bit color or greater
The first time you connect the projector and the computer using the USB
cable, the driver needs to be installed. The procedure is different for
Windows and Mac OS.
a
• You do not need to install the driver the next time you connect.
• When inputting images from multiple sources, change the input
source to USB Display.
• If you use a USB hub, operation may not be performed correctly.
Connect the USB cable directly to the projector.
For Windows
a
Connect the computer's USB port to the projector's USB(TypeB)
port using a commercially available USB cable.
a
For Windows 2000 or Windows XP, a message asking you if
you want to restart your computer may be displayed.Select
No.
For Windows 2000
Double-click Computer, EPSON PJ_UD, and then
EMP_UDSE.EXE.
For Windows XP
Driver installation starts automatically.
For Windows Vista/Windows 7
When the dialog box is displayed, click Run EMP_UDSE.exe.
b
When the License Agreement screen is displayed, click Agree.
Projecting images
c
d
Computer images are projected.
It may take a while for computer images to be projected. Until the
computer images are projected, leave the equipment as is and do not
disconnect the USB cable or turn off the power of the projector.
Disconnect the USB cable when you are finished.
When disconnecting the USB cable, there is no need to use Safely
Remove Hardware.
a
• If it is not installed automatically, double-click My Computer
- EPSON_PJ_UD - EMP_UDSE.EXE on your computer.
32
d
When the License Agreement screen is displayed, click Agree.
Enter the administrator authority password and start the installation.
When the installation is complete, the USB Display icon is displayed
in the Dock and menu bar.
e
Computer images are projected.
f
When you have finished, select Disconnect from the menu bar or
from the USB Display icon on the Dock. You can then disconnect
the USB cable.
• If nothing is projected for some reason, click All Programs EPSON Projector - Epson USB Display - Epson USB
Display Vx.xx on your computer.
It may take a while for computer images to be projected. Until the
computer images are projected, leave the equipment as is and do not
disconnect the USB cable or turn off the power of the projector.
a
• When using a computer running Windows 2000 under user
authority, a Windows error message is displayed and you may
not be able to use the software. In this case, try updating
Windows to the latest version, restart, and then try to connect
again.
For more details, contact your local dealer or the nearest
address provided in the following document.
s Epson Projector Contact List
• If the USB Display setup folder is not displayed automatically
in the Finder, double-click EPSON PJ_UD - USB Display
Installer on your computer.
• If nothing is projected for some reason, click the USB
Display icon in the Dock.
• If there is no USB Display icon in the Dock, double-click
USB Display from the Applications folder.
• If you select Exit from the USB Display icon menu on the
Dock, USB Display does not start automatically when you
connect the USB cable.
For Mac OS
a
b
c
Connect the computer's USB port to the projector's USB(TypeB)
port using a commercially available USB cable.
Uninstalling
The Setup folder of USB Display is displayed in the Finder.
For Windows 2000
Double-click the USB Display Installer icon.
a
b
c
d
Follow the on-screen instructions to install.
Click Start, select Settings, and then click Control Panel.
Double-click Add/Remove Programs.
Click Change or Remove Programs.
Select Epson USB Display and click Change/Remove.
Projecting images
For Windows XP
a
b
c
Click Start, and then click Control Panel.
Double-click Add or Remove Programs.
Select Epson USB Display and click Remove.
For Windows Vista/Windows 7
a
b
c
Click Start, and then click Control Panel.
Click Uninstall a program under Programs.
Select Epson USB Display and click Uninstall.
For Mac OS
a
b
Open the Applications folder, double-click USB Display, and then
double-click Tool.
Run USB Display UnInstaller.
33
Adjusting Projected Images
Correcting Keystone Distortion
You can correct keystone distortion using one of the following methods.
• H/V-Keystone
Manually correct distortion in the horizontal and vertical directions
independently.
34
H/V-Keystone
Manually correct distortion in the horizontal and vertical directions
independently. H/V-Keystone correction is ideal for fine-tuning keystone
distortion.
You can use H/V-Keystone to correct the projected image under the
following conditions.
Correction angle: approx 15˚ right and left/approx. 15˚ up and down
a
Press the [
] or [
] buttons on the control panel during
projection to display the Keystone screen.
b
Press the following buttons to correct keystone distortion.
• Quick Corner
Manually correct the four corners independently.
a
Press the [w] or [v] buttons to correct vertical distortion.
When you correct keystone distortion, the projected image may be
reduced.
Press the [Tele] or [Wide] buttons to correct horizontal distortion.
Adjusting Projected Images
a
35
You can set H/V-Keystone from the Configuration menu.
s Settings - Keystone - H/V-Keystone p.63
Quick Corner
c
Select Quick Corner, and then press the [
d
Using the [
] button.
This allows you to manually correct each of the four corners of the
projected image separately.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.57
Using Remote Control
Using the Control Panel
], [
control, or the [
], [ ], and [ ] buttons on the remote
], [
], [Wide], and [Tele] buttons on the
control panel, select the corner to correct, and then press the [
button.
b
Select Keystone from Settings.
]
Adjusting Projected Images
e
Using the [
], [
], [ ], and [ ] buttons on the remote
control, or the [
], [
], [Wide], and [Tele] buttons on the
control panel, correct the position of the corner.
When you press the [
displayed.
] button, the screen shown in step 4 is
If the message "Cannot adjust any further." is displayed while
adjusting, you cannot adjust the shape any further in the direction
indicated by the gray triangle.
36
f
Repeat procedures 4 and 5 as needed to adjust any remaining
corners.
g
When you are done, press the [Esc] button to exit the correction
menu.
Because Keystone was changed to Quick Corner, the corner
selection screen from step 4 is displayed when you press the [
]
] buttons on the control panel next time. Change Keystone
and [
to H/V-Keystone if you want to perform horizontal and vertical
correction using the [
] and [
] buttons on the control panel.
s Settings - Keystone - H/V-Keystone p.63
Adjusting Projected Images
a
If the [Esc] button is held down for about two seconds while
the corner selection screen from step 4 is displayed, the
following screen is displayed.
Reset Quick Corner: Resets the result of Quick Corner
corrections.
Switch to H/V-Keystone: Switches the correction method to
H/V-Keystone.
s "Settings Menu" p.63
Adjusting the Image Size
Press the [Wide] and [Tele] buttons on the control panel to adjust the size
of the projected image.
a
37
Adjusting the Image Position
Press the foot lever to extend and retract the front foot. You can adjust the
position of the image by tilting the projector up to 10 degrees.
a
The larger the angle of tilt, the harder it becomes to focus. Install the
projector so that it only needs to be tilted at a small angle.
Adjusting the Horizontal Tilt
Extend and retract the rear feet to adjust the projector's horizontal tilt.
You can also make adjustments from the configuration menu.
s Settings - Zoom p.63
A Extend the rear foot.
Adjusting Projected Images
B Retract the rear foot.
38
• Adjust the volume from the Configuration menu.
s Settings - Volume p.63
Caution
Correcting the Focus
You can correct the focus using the focus ring.
Do not start when the volume is set too high.
A sudden increase in volume may cause loss of hearing. Always lower the
volume before powering off, so that you can power on and then gradually
increase the volume.
Selecting the Projection Quality (Selecting Color
Mode)
Adjusting the Volume
You can easily obtain the optimum image quality simply by selecting the
setting that best corresponds to your surroundings when projecting. The
brightness of the image varies depending on the mode selected.
Mode
Application
You can adjust the volume using one of the following methods.
Dynamic
• Press the [Volume] buttons on the remote control to adjust the volume.
[a] Decreases the volume.
[b] Increases the volume.
Ideal for use in a bright room. This is the brightest
mode, and reproduces shadow tones well.
Presentation
Ideal for making presentations using color materials
in a bright room.
Theatre
Ideal for watching films in a dark room. Gives
images a natural tone.
Photo*1
Ideal for projecting still pictures, such as photos, in
a bright room. The images are vivid and brought
into contrast.
Sports *2
Ideal for watching TV programmes in a bright
room. The images are vivid and brought to life.
sRGB
Ideal for images that conform to the sRGBg color
standard.
Remote control
Adjusting Projected Images
Mode
Blackboard
Whiteboard
39
Application
Even if you are projecting onto a blackboard
(greenboard), this setting gives your images a
natural tint, just like when projecting onto a screen.
a
Press the [Menu] button.
s "Using the Configuration Menu" p.57
Using Remote Control
Using the Control Panel
Ideal for making presentations using a whiteboard.
*1 This selection is only available when the input signal is RGB or when the
source is USB Display, USB, or LAN.
*2 This can be selected when inputting component video signals, S-video signals,
or composite video signals.
Each time you press the [Color Mode] button, the Color Mode name is
displayed on the screen and the Color Mode changes.
Remote control
a
b
Select Auto Iris from Image.
c
Select On.
You can set Color Mode from the Configuration menu.
s Image - Color Mode p.60
Setting Auto Iris
By automatically setting the luminance according to the brightness of the
displayed image, it lets you enjoy deep and rich images.
d
The setting is stored for each Color Mode.
Press the [Menu] button to finish making settings.
a
Auto Iris can only be set when the Color Mode is set to
Dynamic or Theatre.
Adjusting Projected Images
40
Changing the Aspect Ratio of the Projected Image
You can change the Aspect Ratiog of the projected image to suit the type,
the ratio of height and width, and the resolution of the input signals.
Available Aspect Modes vary depending on the image signal currently being
projected.
Changing methods
Each time you press the [Aspect] button, the Aspect Mode name is
displayed on the screen and the aspect ratio changes.
Remote control
A
B
C
D
E
a
Normal or Auto
16:9
Full
Zoom
Native
Projecting images from a computer
You can set the aspect ratio from the Configuration menu.
s Signal - Aspect p.61
The following shows projection examples for each aspect mode.
Aspect mode
Input Signal
XGA 1024X768(4:3)
Changing the aspect mode (EB-435W/EB-425W only)
Projecting images from video equipment or from the HDMI port
Each time the [Aspect] button on the remote control is pressed, the aspect
mode changes in the order Normal or Auto, 16:9, Full, Zoom, and
Native.
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
Normal
WXGA 1280X800(16:10)
Adjusting Projected Images
Aspect mode
41
Input Signal
XGA 1024X768(4:3)
Changing the aspect mode (EB-430/EB-420 only)
WXGA 1280X800(16:10)
Projecting images from video equipment
16:9
Each time the [Aspect] button on the remote control is pressed, the aspect
mode changes in the order 4:3 and 16:9.
When inputting a 720p/1080i signal and the aspect mode is set to 4:3, a 4:3
zoom is applied (the right and left sides of the image are cut off).
Full
Example: 720p signal input (resolution: 1280x720, aspect ratio: 16:9)
Zoom
A 4:3
B 16:9
Native
Projecting images from the HDMI port
Each time the [Aspect] button on the remote control is pressed, the aspect
mode changes in the order Auto, 4:3, and 16:9.
a
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
If parts of the image are missing, set the Resolution setting to Wide
or Normal from the Configuration menu, according to the size of the
computer panel.
s Signal - Resolution p.61
A Auto
Adjusting Projected Images
42
B 4:3
C 16:9
Projecting images from a computer
Each time the [Aspect] button on the remote control is pressed, the aspect
mode changes in the order Normal, 4:3, and 16:9.
The following shows projection examples for each aspect mode.
Aspect mode
Input Signal
XGA 1024X768(4:3)
WXGA 1280X800(16:10)
Normal
4:3
16:9
a
If parts of the image are missing, set the Resolution setting to Wide
or Normal from the Configuration menu, according to the size of the
computer panel.
s Signal - Resolution p.61
Useful Functions
This chapter explains useful functions for giving presentations and so on, and the security functions.
Projection Functions
Hiding the Image and Sound Temporarily (A/V
Mute)
You can use this when you want to focus the audience's attention on what
you are saying, or if you do not want to show details such as when you are
changing between files during presentations from a computer.
44
a
• If you use this function when projecting moving images, the images
and sound continue to be played back by the source, and you cannot
return to the point where A/V Mute was activated.
• Microphone audio is still output even when A/V Mute is turned
on.
• You can select the screen displayed when the [A/V Mute] button is
pressed from the Configuration menu.
s Extended - Display - A/V Mute p.64
• The lamp is still lit during A/V Mute, so the lamp hours continue to
accumulate.
Freezing the Image (Freeze)
Each time you press the [A/V Mute] button, A/V Mute turns on or off.
Remote control
When Freeze is activated on moving images, the frozen image continues to
project on the screen, so you can project a moving image one frame at a
time like a still photo. Also, you can perform operations such as changing
between files during presentations from a computer without projecting any
images if the Freeze function is activated beforehand.
Each time you press the [Freeze] button, Freeze turns on or off.
Remote control
Projection Functions
a
• Audio does not stop.
• For moving images, the images continue to play back while the
screen is frozen, so it is not possible to resume projection from the
point where the screen was frozen.
• If the [Freeze] button is pressed while the Configuration menu or
the Help screen is displayed, the menu or the Help screen that is
displayed is closed.
• Freeze still works while E-Zoom is being used.
Pointer Function (Pointer)
This allows you to move a pointer icon on the projected image, and helps
you draw attention to the area you are talking about.
a
Display the Pointer.
Each time you press the [Pointer] button, the pointer appears or
disappears.
Remote control
45
b
Move the Pointer icon (
).
Remote control
When any pair of adjacent [
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
a
You can select the shape of the pointer icon from the
Configuration menu.
s Settings - Pointer Shape p.63
Projection Functions
46
Enlarging Part of the Image (E-Zoom)
b
This is useful when you want to expand images to see them in greater
detail, such as graphs and tables.
a
Move the Cross (
) to the area of the image that you want to
enlarge.
Remote control
When any pair of adjacent [
Start E-Zoom.
Press the [z] button to display the Cross (
Remote control
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
).
c
Enlarge.
Remote control
[z] button: Expands the area each time
it is pressed. You can expand quickly by
holding the button down.
[x] button: Reduces images that have
been enlarged.
[Esc] button: Cancels E-Zoom.
a
• The enlargement ratio appears on the screen. The selected
area can be enlarged to between 1 to 4 times in 25
incremental steps.
• During enlarged projection, press the [
[ ] buttons to scroll the image.
], [
], [ ], and
Projection Functions
47
Using the Remote Control to Operate the Mouse
Pointer (Wireless Mouse)
Once the connection has been made, the mouse pointer can be operated as
follows.
Moving the mouse pointer
When the USB port of a computer and the USB(TypeB) port on the
projector are connected with a commercially available USB cable, you can
use the remote control to control the computer's mouse pointer.
[
][
][ ][ ] buttons:
Moves the mouse pointer.
Mouse clicks
[ ] button: Left click. Press quickly twice to
double-click.
[Esc] button: Right click.
This is available when projecting images from a computer connected to the
Computer1, Computer2, or HDMI ports.This is also available when
projecting in USB Display.
The following operating systems are compatible with Wireless Mouse.
Windows
OS
Windows
Windows
Windows
Windows
Windows
Windows
Windows
Mac OS
98
98SE
Me
2000
XP
Vista
7
Mac
Mac
Mac
Mac
OS
OS
OS
OS
Drag and drop
X
X
X
X
While holding down the [
10.3.x
10.4.x
10.5.x
10.6.x
It may not be possible to use the Wireless Mouse function under some versions of
the operating systems.
the [
], [
] button, press
], [ ], and [ ] buttons.
Release the [ ] button to drop at the
desired location.
Page Up/Down
[[] button: Moves to the previous page.
[]] button: Moves to the next page.
Projection Functions
a
• When any pair of adjacent [
48
], [
], [ ], or [ ] buttons are
pressed at the same time, the pointer can be moved diagonally.
• If the mouse button settings are set to reverse on the computer, the
operation of the remote control buttons will also be reversed.
• The Wireless Mouse function does not operate under the following
conditions.
- When the configuration menu or a Help screen is displayed
- When operating functions other than the Wireless Mouse function
(such as adjusting the volume).
However, when using the E-Zoom or Pointer function, the page up
or down function is available.
Saving a User's Logo
You can save the image that is currently being projected as a User's Logo.
You can use the registered user's logo as a display when projection starts or
no image signal is being input.
s Extended - Display p.64
a
a
Once a User Logo has been saved, the logo cannot be returned to the
factory default.
Project the image you want to save as the User's Logo, and then
press the [Menu] button.
s "Using the Configuration Menu" p.57
Using Remote Control
b
Select User's Logo from Extended.
Using the Control Panel
Projection Functions
49
d
Move the box to select the part of the image to use as the User's
Logo.
You can perform the same operations from the projector's control
panel.
Remote control
a
• When User's Logo Protect from Password Protect is set to
On, a message is displayed and the User's Logo cannot be
changed. You can make changes after setting User's Logo
Protect to Off.
s "Managing Users (Password Protect)" p.52
• If User's Logo is selected when Keystone, E-Zoom, Aspect, or
Adjust Zoom is being performed, the function currently being
performed is cancelled.
c
When the message "Choose this image as the User's Logo?" is
displayed, select Yes.
a
When you press the [ ] button on the remote control or the
control panel, the screen size may change depending on the
signal to match the actual resolution of the image signal.
a
e
You can save at 400x300 dots in size.
When you press the [ ] button and the message "Select this
image?" is displayed, select Yes.
Projection Functions
f
Select the zoom factor from the zoom setting screen.
50
a
a
When a User Pattern is saved, the previous User Pattern is erased.
Project the image you want to use as the User Pattern, and then
press the [Menu] button.
s "Using the Configuration Menu" p.57
Using Remote Control
g
When the message "Save this image as the User's Logo?" is
displayed, select Yes.
The image is saved. After the image has been saved, the message
"Completed." is displayed.
a
• When a User's Logo is saved, the previous User's Logo is
erased.
• It takes a while to save. Do not operate the projector or any
connected equipment while it is saving, otherwise
malfunctions may occur.
b
Select Pattern from Settings.
c
Select User Pattern.
Saving User Pattern
There are four types of patterns registered to the projector, such as ruled
lines and grid patterns.
s Settings - Pattern - Pattern Type p.63
You can also save the image that is currently being projected as a User
Pattern.
Using the Control Panel
Projection Functions
a
If User Pattern is selected when Keystone, E-Zoom, Aspect, or
Adjust Zoom is being performed, the function currently being
performed is cancelled.
d
When "Do you want to use the currently projected image as the
User Pattern?" is displayed, select Yes.
e
When you press the [ ] button, the message "Do you want to use
the currently projected image as the User Pattern?" is displayed.
Then, select Yes.
The image is saved. After the image has been saved, the message
"The User Pattern setting is complete." is displayed.
a
• Once a User Pattern has been saved, User Pattern cannot be
returned to the factory default.
• It takes a while to save a User Pattern. Do not operate the
projector or any connected equipment while it is saving,
otherwise malfunctions may occur.
51
Security Functions
The projector has the following enhanced security functions.
• Password Protect
You can limit who can use the projector.
• Control Panel Lock
You can prevent people changing the settings on the projector without
permission.
s "Restricting Operation (Control Panel Lock)" p.54
• Anti-Theft Lock
The projector is equipped with the following anti-theft security device.
s "Anti-Theft Lock" p.55
52
• User's Logo Protect
Even if someone tries to change the User's Logo set by the owner of the
projector, it cannot be changed. When User's Logo Protect is set to On,
the following setting changes for the User's Logo are prohibited.
• Capturing a User's Logo
• Setting Display Background, Startup Screen, or A/V Mute from
Display
s Extended - Display p.64
• Network Protect
When Network Protect is set to On, changing the settings for Network is
prohibited.
s "Network Menu" p.66
Managing Users (Password Protect)
When Password Protect is activated, people who do not know the password
cannot use the projector to project images even if the projector power is on.
Furthermore, the user's logo that is displayed when you turn on the
projector cannot be changed. This acts as an anti-theft device as the
projector cannot be used even if it is stolen. At the time of purchase,
Password Protect is not activated.
Setting Password Protect
Use the following procedure to set Password Protect.
a
During projection, hold down the [Freeze] button for about five
seconds.
The Password Protect setting menu is displayed.
Remote control
Kinds of Password Protect
The following three kinds of Password Protect settings can be made
according to how the projector is being used.
• Power On Protect
When Power On Protect is On, you need to enter a preset password after
the projector is plugged in and turned on (this also applies to Direct
Power On). If the correct password is not entered, projection does not
start.
Security Functions
a
53
• If Password Protect is already activated, you must enter the
password.
If the password is entered correctly, the Password Protect
setting menu is displayed.
s "Entering the Password" p.53
(3)
While holding down the [Num] button, enter a four digit number using
the numeric buttons. The number entered is displayed as "* * * *". When
you enter the fourth digit, the confirmation screen is displayed.
Remote control
• When the password is set, stick the supplied password protect
sticker in a visible position on the projector as a further theft
deterrent.
b
Select the type of Password Protect you want to set, and then
press the [ ] button.
(4)
Re-enter the password.
"Password accepted." is displayed.
If you enter the password incorrectly, a message is displayed prompting
you to re-enter the password.
Entering the Password
When the password entry screen is displayed, enter the password using the
numeric buttons on the remote control.
While holding down the [Num] button, enter the password by pressing the
numeric buttons.
c
Select On, and then press the [
d
Set the password.
] button.
Press the [Esc] button, the screen displayed in step 2 is displayed
again.
(1)
Select Password, and then press the [
(2)
When the message "Change the password?" is displayed, select Yes and
then press the [ ] button. The default password is set to "0000". Change
this to your own desired Password. If you select No, the screen displayed
in step 2 is displayed again.
] button.
Security Functions
When you enter the correct password, Password Protect is temporarily
released.
Attention
• If an incorrect password is entered three times in succession, the message
"The projector's operation will be locked." is displayed for approximately five
minutes, and then the projector switches to standby mode. If this happens,
disconnect the power plug from the electrical outlet and then reinsert it and
turn the projector's power back on. The projector displays the password entry
screen again so that you can enter the correct password.
54
This is useful at events or shows when you want to deactivate all buttons
during projection or at schools when you want to limit button operation.
The projector can still be operated using the remote control.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.57
Using Remote Control
Using the Control Panel
• If you have forgotten the password, make a note of the "Request Code:
xxxxx" number that appears on the screen and contact the nearest address
provided in the Epson Projector Contact List.
s Epson Projector Contact List
• If you continue to repeat the above operation and input the wrong Password
thirty times in succession, the following message is displayed and the
projector does not accept any more Password entries. "The projector's
operation will be locked. Contact Epson as described in your documentation."
s Epson Projector Contact List
b
Select Control Panel Lock from Settings.
c
Select either Full Lock or Partial Lock according to your purpose.
Restricting Operation (Control Panel Lock)
Do one of the following to lock the operation buttons on the control
panel.
• Full Lock
All of the buttons on the control panel are locked. You cannot perform
any operations from the control panel, including turning the power on or
off.
• Partial Lock
All of the buttons on the control panel, except for the [t] button, are
locked.
Security Functions
55
Anti-Theft Lock
The projector is equipped with the following types of anti-theft security
devices.
d
Select Yes when the confirmation message is displayed.
The control panel buttons are locked according to the setting you
chose.
a
You can release the control panel lock by one of the following
two methods.
• Select Off from Control Panel Lock.
s Settings - Control Panel Lock p.63
• Press and hold down the [ ] button on the control panel for
about seven seconds, a message is displayed and the lock is
released.
• Security slot
The security slot is compatible with the Microsaver Security System
manufactured by Kensington.
See the following for more details on the Microsaver Security System.
s http://www.kensington.com/
• Security cable installation point
A commercially available theft-prevention wire lock can be passed
through the installation point to secure the projector to a desk or pillar.
Installing the wire lock
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking instructions.
Configuration Menu
This chapter explains how to use the Configuration menu and its functions.
Using the Configuration Menu
This section explains how to use the Configuration menu.
Although steps are explained using the remote control as an example, you
can perform the same operations from the control panel. Check the guide
under the menu for the available buttons and their operations.
a
b
57
c
Select a submenu item.
d
Change settings.
e
Press the [Menu] button to finish making settings.
Display the Configuration menu screen.
Select a top menu item.
List of Functions
58
Top Menu Name
Configuration Menu Table
Submenu Name
Video Signal
Auto, NTSC, NTSC4.43, PAL,
M-PAL, N-PAL, PAL60, and
SECAM
Aspect
Normal, Auto, 4:3, 16:9, Full,
Zoom, and Native
Overscan
Auto, Off, 4%, and 8%
Keystone
H/V-Keystone and Quick Corner
Zoom
0 (Wide) to 40 (Tele)
Settable items vary depending on the model being used and the image
signal and source being projected.
Top Menu Name
Image menu
s p.60
Signal menu
s p.61
Submenu Name
Color Mode
Items or Setting Values
Dynamic, Presentation, Theatre,
Photo, Sports, sRGB, Blackboard,
and Whiteboard
Settings menu
s p.63
Items or Setting Values
Brightness
-24 - 24
Contrast
-24 - 24
Control Panel Lock
Full Lock, Partial Lock, and Off
Color Saturation
-32 - 32
Pointer Shape
Pointer 1, Pointer 2, Pointer 3
Tint
-32 - 32
Power Consumption
Normal and ECO
Sharpness
-5 - 5
Volume
0 - 20
Abs. Color Temp.
5000K to 10000K
Mic Input Level
0 - 5
Color Adjustment
Red: -16 to 16
Green: -16 to 16
Blue: -16 to 16
Remote Receiver
Front/Rear, Front, Rear and Off
User Button
Power Consumption, Info,
Progressive,Test Pattern,
Resolution, Mic Input Level, and
Pattern Display
Pattern
Pattern Display, Pattern Type,
User Pattern, and Test Pattern
Display
Messages, Display Background,
Startup Screen, and A/V Mute
Auto Iris
On and Off
Auto Setup
On and Off
Resolution
Auto, Wide, and Normal
Tracking
-
Sync.
-
Position
Up, Down, Left, and Right
User's Logo
-
Progressive
Off, Video, and Film/Auto
Projection
Noise Reduction
Off, NR1, and NR2
Front, Front/Ceiling, Rear, and
Rear/Ceiling
HDMI Video Range
Auto, Normal, and Expanded
Operation
Input Signal
Auto, RGB, and Component
Direct Power On, Sleep Mode,
Sleep Mode Timer, High
Altitude Mode, and Audio Input
Standby Mode
Communication On and
Communication Off
Extended menu
s p.64
List of Functions
Top Menu Name
Info menu
s p.74
Reset menu
s p.75
59
Submenu Name
Items or Setting Values
Top Menu Name
On and Off
Wireless LAN Sys.
802.11b/g and 802.11b/g/n
Language
15 or 35 languages*1
SSID Auto Setting
On and Off
Lamp Hours
-
SSID
-
Source
-
IP Settings
Input Signal
-
DHCP, IP Address, Subnet Mask,
and Gateway Address
Resolution
-
SSID Display
On and Off
Video Signal
-
IP Address Display
On and Off
Refresh Rate
-
Security
No, WEP, WPA-PSK, and WPA2PSK
Sync Info
-
WEP Encryption
128Bit and 64Bit
Status
-
Format
ASCII and HEX
Serial Number
-
Key ID
1, 2, 3, 4
Event ID
-
Reset All
-
Reset Lamp Hours
-
Security menu
s p.70
Encryption Key 1, En‐ cryption Key 2, Encryp‐
tion Key 3, and Encryp‐
tion Key 4
Wired LAN menu
s p.71
Network menu
Basic menu
s p.68
Wireless LAN menu
s p.68
Items or Setting Values
Standby Microphone
*1 The number of supported languages differs depending on the region where the
projector is used.
Top Menu Name
Submenu Name
Submenu Name
Items or Setting Values
Mail menu
s p.72
Authentication Type
Open and Shared
PSK
-
IP Settings
DHCP, IP Address, Subnet Mask,
and Gateway Address
IP Address Display
On and Off
Mail Notification
On and Off
SMTP Server
-
Projector Name
-
PJLink Password
-
Web Control Password
-
Port Number
Projector Keyword
On and Off
Wireless LAN Power
On and Off
Address 1 Setting, Ad‐ dress 2 Setting, and Ad‐
dress 3 Setting
Connection Mode
Quick and Advanced
Channel
1ch, 6ch, and 11ch
Others menu
s p.73
SNMP
On and Off
List of Functions
Top Menu Name
60
Submenu Name
Items or Setting Values
Trap IP Address 1 and
Trap IP Address 2
-
Priority Gateway
Wired LAN and Wireless LAN
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.29
AMX Device Discovery On and Off
Crestron RoomView
On and Off
Bonjour
On and Off
Image Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
Sub-menu
Function
Color Mode
You can select the quality of the image to suit your surroundings.
s "Selecting the Projection Quality (Selecting Color Mode)"
p.38
Brightness
You can adjust the image brightness.
Contrast
You can adjust the difference between light and dark in the
images.
Color Saturation
You can adjust the color saturation for the images.
Tint
You can adjust the image tint.
Sharpness
You can adjust the image sharpness.
Abs. Color Temp.
(This item cannot be selected if Color Mode is set to sRGBg.)
You can adjust the overall tint of the image.You can adjust tints in
10 stages from 5000 K to 10000 K. The image is tinted blue when a
high value is selected and tinted red when a low value is selected.
List of Functions
Sub-menu
61
Function
Color Adjustment
(This item cannot be selected if Color Mode is set to sRGBg.)
You can adjust the color strength for Red, Green, and Blue
individually.
Auto Iris
(This item can be set only if Color Mode is set to Dynamic or
Theatre.)
Set to On to adjust the iris to obtain the optimum light for images
being projected.
The setting is stored for each Color Mode.
s "Setting Auto Iris" p.39
Reset
Signal Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
You cannot make settings on the Signal menu when the source is USB
Display, USB, or LAN.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.29
You can reset all adjustment values for the Image menu to their
default settings. See the following to return all menu items to
their default settings.
s "Reset Menu" p.75
Sub-menu
Function
Auto Setup
Set to On to automatically adjust Tracking, Sync., and Position to
the optimum state when the input signal changes.
Resolution
Set to Auto to automatically identify the resolution of the input
signal. If images are not projected correctly when set to Auto, for
example if some of the image is missing, adjust to Wide for wide
screens, or set to Normal for 4:3 or 5:4 screens depending on the
connected computer.
Tracking
You can adjust computer images when vertical stripes appear in
the images.
List of Functions
Sub-menu
62
Function
Sync.
You can adjust computer images when flickering, fuzziness, or
interference appear in the images.
Position
You can adjust the display position up, down, left, and right when
a part of the image is missing so that all of the image is projected.
Progressive
Interlaceg (i) signal is converted to Progressiveg (p). (IP
conversion)
Off: Ideal for images with a large amount of movement.
Video: Ideal for general video images.
Film/Auto: This is ideal for movie films, computer graphics, and
animation.
Noise Reduction
(This cannot be set when a digital RGB signal is input, or when an
interlace signal is being displayed when Progressive is set to
Off.)
Smoothes out rough images. There are two modes. Select your
favorite setting. It is recommended that this is set to Off when
viewing image sources in which noise is very low, such as for
DVDs.
HDMI Video
Range
When the projector's HDMI port is connected to a DVD player,
the projector's video range is set according to the DVD player's
video range setting.
Input Signal
You can select the input signal from the Computer1 port or the
Computer2 port.
If set to Auto, the input signal is set automatically according to
the connected equipment.
If colors do not appear correctly when set to Auto, select the
appropriate signal according to the connected equipment.
Video Signal
You can select the input signal from the S-Video port or the
Video port. If set to Auto, video signals are recognized
automatically. If interference appears in the image or a problem
occurs such as no image is being projected when set to Auto,
select the appropriate signal according to the connected
equipment.
Aspect
You can set the aspect ratiog for projected images.
s "Changing the Aspect Ratio of the Projected Image" p.40
Sub-menu
Function
Overscan
Changes the output image ratio (the range of the projected
image). You can set the cropping range to Off, 4%, or 8%. When
the source is HDMI, Auto is available. When Auto is selected, it
automatically changes to Off or 8% according to the input signal.
Reset
You can reset all adjustment values on the Signal menu to their
default settings, except for Input Signal.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.75
List of Functions
63
Sub-menu
Settings Menu
Pointer Shape
Function
You can select the shape of the pointer.
Pointer 1:
Pointer 2:
Pointer 3:
s "Pointer Function (Pointer)" p.45
Sub-menu
Function
Keystone
You can correct keystone distortion.
• When H/V-Keystone is selected:
Adjust V-Keystone and H-Keystone to correct horizontal
and vertical keystone distortion.
• When Quick Corner is selected:
Select and correct the four corners of the projected image.
s "Quick Corner" p.35
Zoom
Adjusts the projected image size.
Control Panel
Lock
You can use this to restrict operation of the projector's control
panel.
s "Restricting Operation (Control Panel Lock)" p.54
Power Consumption
You can set the lamp brightness to one of two settings.
Select ECO if the images being projected are too bright, such as
when projecting images in a dark room or onto a small screen.
When ECO is selected, the amount of electricity consumed and
the lamp's operating life are changed as follows, and fan rotation
noise during projection is reduced.
Electrical consumption: about 16 to 26% decrease, lamp life:
about 1.2 to 1.5 times longer
Volume
You can adjust the volume. Setting values are saved for each
source.
Mic Input Level
Adjust this if the microphone input level is low and the
microphone audio output from the projector's speaker is difficult
to hear, or if the input level is too high, resulting in a crackling
sound in the audio from the microphone.When Mic Input Level
is turned down to 0, no microphone audio is output from the
speaker.
When the microphone input level is raised, the audio from the
connected device becomes quieter. When the microphone input
level is lowered, the audio from the connected device becomes
louder.
Remote Receiver
You can limit the reception of the operation signal from the
remote control.
When set to Off, you cannot perform any operations from the
remote control. If you want to make operations from the remote
control, hold down the [Menu] button on the remote control for
at least 15 seconds to reset the setting to its default value.
List of Functions
64
Sub-menu
Function
User Button
You can select the item assigned from the Configuration menu
with the remote control's [User] button. By pressing the [User]
button the assigned menu item selection/adjustment screen is
displayed, allowing you to make one-touch settings/
adjustments. You can assign one of the following items to
the [User] button.
Power Consumption, Info, Progressive,Test Pattern,
Resolution, Mic Input Level, and Pattern Display
Pattern
Pattern Display: Display a pattern.
Pattern Type: You can select from Patterns 1 to 4 or User
Pattern. Patterns 1 to 4 display projection lines such as ruled lines
or a grid.
Pattern 1:
Pattern 2:
Pattern 3:
Pattern 4:
User Pattern: Captures a user pattern.
s "Saving User Pattern" p.50
Test Pattern: When the projector is set up, a test pattern is
displayed so that you can adjust the projection status without
connecting equipment. While the test pattern is displayed, zoom,
focus adjustments, and keystone correction can be performed.
To cancel the Test Pattern, press the [Esc] button on the remote
control or the control panel.
Attention
If a pattern is displayed for a long time, a residual
image may be visible in projected images.
Sub-menu
Reset
Function
You can reset all adjustment values in the Settings menu to their
default settings, except for Zoom and User Button.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.75
Extended Menu
List of Functions
Sub-menu
65
Function
Display
You can make settings related to the projector's display.
Messages: When set to Off, the following items will not be
displayed.
Item names when the Source, Color Mode, or Aspect Ratio
is changed, messages when no signal is being input, and
warnings such as High Temp Warning.
Display Background*1: You can set the screen status for
when no image signal is available to Black, Blue, or
Logo.
Startup Screen*1: Set to On to display the User's Logo
when projection starts.
A/V Mute*1: You can set the screen displayed when the
remote control's [A/V Mute] button is pressed to Black,
Blue, or Logo.
User's Logo *1
You can change the user's logo that is displayed as a
background during Display Background, A/V Mute, and so
on.
s "Saving a User's Logo" p.48
Projection
Select from one of the following projection methods
depending on how the projector is installed.
Front, Front/Ceiling, Rear, and Rear/Ceiling
You can change the setting as follows by pressing down
the [A/V Mute] button on the remote control for about five
seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
s "Installation Methods" p.17
Sub-menu
Function
Operation
Direct Power On: Set to On to turn on the projector
simply by plugging it in.
When the power cable is plugged in, note that the projector
turns on automatically in cases such as a power outage
being restored.
Sleep Mode: When this is set to On, the power is turned
off automatically when no image signal is input and no
operation is performed within a certain amount of time.
Sleep Mode Timer: When Sleep Mode is set to On, you
can set the time before the projector automatically turns off
within a range of 1 to 30 minutes.
High Altitude Mode: Set this to On when using the
projector at an altitude of 1500 m or above.
Audio Input: When set to Auto, audio for the image
currently being projected is output.If anything other than
Auto is selected, audio for the selected audio input port is
output.When the input source is HDMI, USB Display, or
LAN, the audio for the image currently being projected is
output regardless of the Audio Input setting.
Standby Mode
If you set Communication On, you can perform the
following operations even if the projector is in standby
mode.
• Monitoring and controlling the projector over the
network.
s "Monitoring and Controlling" p.108
• Outputting analog RGB signals from the Computer1 port
to an external monitor.
• Outputting audio from the microphone to the projector's
speaker.
(Only when the Standby Microphone is set to On.)
s "Connecting Image Sources" p.19
Standby Microphone
(This item is settable only when Standby Mode set to
Communication On.)
When set to On, you can output audio from the
microphone from the projector's speaker even if the
projector is in standby mode.
List of Functions
Sub-menu
66
Function
Language
You can set the language for messages and menus.
Reset
You can reset the adjustment values for Display*1 and
Operation*2 from the Extended menu to their default
settings.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.75
*1 When User's Logo Protect is set to On in Password Protect, settings related
to user's logo cannot be changed. You can make changes after setting User's
Logo Protect to Off.
s "Managing Users (Password Protect)" p.52
*2 Except for High Altitude Mode.
Sub-menu
Function
Net. Info. - Wireless LAN
Displays the following network setting status information.
• Connection Mode
• Antenna Level
• Projector Name
• SSID
• DHCP
• IP Address
• Subnet Mask
• Gateway Address
• MAC Address
• Region Code*
Net. Info. Wired LAN
Displays the following network setting status information.
• Projector Name
• DHCP
• IP Address
• Subnet Mask
• Gateway Address
• MAC Address
Network Configuration
The following menus are available for setting network items.
Basic, Wireless LAN, Security, Wired LAN, Mail, Others,
Reset, and Setup complete
Network Menu
When Network Protect is set to On in Password Protect, a message is
displayed and the network settings cannot be changed. Turn Network
Protect Off and then configure the network.
s "Setting Password Protect" p.52
*
Displays available region information for the Wireless LAN unit being used.
For more details, contact your local dealer or the nearest address provided in
the Epson Projector Contact List.
s Epson Projector Contact List
a
By using a Web browser of a computer connected to the projector on
a network, you can set functions and control the projector. This
function is called Web Control. You can easily enter text using a
keyboard to make settings for Web Control such as Security settings.
s "Changing Settings Using a Web Browser (Web Control)"
p.108
List of Functions
67
Notes on operating the Network menu
Selecting from the top menu and sub menus, and changing selected items is
the same as making operations from the Configuration menu.
When done, make sure you go to the Setup complete menu, and select one
of Yes, No, or Cancel. When you select Yes or No, you return to the
Configuration menu.
• Each time the CAPS key is selected and the [
sets and changes between upper case and lower
• Each time the SYM1/2 key is selected and the [
sets and changes the symbol keys for the section
Yes: Saves the settings and exits the Network menu.
No: Does not save the settings and exits the Network menu.
Cancel: Continues displaying the Network menu.
Soft keyboard operations
The Network menu contains items that require input of alphanumerics
during setup. In this case, the following software keyboard is displayed.Use
the [
], [
], [ ], and [ ] buttons on the remote control or the [
],
], [Wide], and [Tele] buttons on the control panel to move the cursor
[
to the desired key, and then press the [ ] button to enter the
alphanumeric character. Enter figures by holding down the [Num] button
on the remote control, and pressing the numeric buttons. After inputting,
press Finish on the keyboard to confirm your input. Press Cancel on the
keyboard to cancel your input.
] button is pressed, it
case letters.
] button is pressed, it
enclosed by the frame.
List of Functions
68
Basic menu
Sub-menu
Projector Keyword
Function
When set to On, you have to enter the keyword when you try to
connect the projector to a computer via a network. As a result,
you can prevent presentations from being interrupted by
connections from other computers.
Normally this should be set to On.
s EasyMP Network Projection Operation Guide
Wireless LAN menu
Sub-menu
Function
Projector Name
Displays the projector name used to identify the projector when
connected to a network.
When editing, you can enter up to 16 single-byte alphanumeric
characters.
PJLink Password
Set a password to use when you access the projector using
compatible PJLink software.
You can enter up to 32 single-byte alphanumeric characters.
Web Control
Password
Set a password to use when making settings and controlling the
projector using Web Control. Enter no more than eight singlebyte alphanumeric characters. Web Control is a computer
function that allows you to set up and control the projector by
using the Web browser on a computer connected on a Network.
s "Changing Settings Using a Web Browser (Web Control)"
p.108
Sub-menu
Wireless LAN
Power
Function
Turn On when connecting the projector to the computer over
wireless LAN.
If you do not want to connect via wireless LAN, turn it Off to
prevent unauthorized access by others.
This is set to On by default.
List of Functions
Sub-menu
69
Function
Connection
Mode
Set the connection mode when using EasyMP Network
Projection to connect the projector and computer.
This is set to Quick by default.
See the following manual for details on Connection Mode.
s EasyMP Network Projection Operation Guide
Channel
(This can only be set if Connection Mode is set to Quick.)
Select the frequency band used by the wireless LAN from 1ch,
6ch, or 11ch.
This is set to 11ch by default.
Wireless LAN
Sys.
Set the Wireless LAN Sys. to either 802.11b/g or 802.11b/g/n.
The default value is 802.11b/g/n.
SSID Auto Setting
(This can only be set if Connection Mode is set to Quick.)
Set to On to speed up the projector search.
Set to Off when connecting to multiple projectors at the same
time.
This is set to On by default.
SSID
(This can be set only if SSID Auto Setting is set to Off.)
Enter an SSIDg. When an SSID is provided for the wireless LAN
system in which the projector participates, enter the SSID.
You can enter up to 32 single-byte alphanumeric characters.
Sub-menu
Function
IP Settings
(This can be set only if Connection Mode is set to Advanced.)
You can make network settings.
DHCP: Set to On to make network settings using DHCPg. If this
is set to On, you cannot set any more addresses.
IP Address: You can input the IP addressg assigned to the
projector. You can enter a number from 0 to 255 in each field of
the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Mask: You can input the subnet maskg for the projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address: You can input the IP address for the gateway
for the projector. You can enter a number from 0 to 255 in each
field of the address. However, the following Gateway addressesg
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
SSID Display
To prevent the SSIDg from being displayed on the LAN Standby
screen, set this to Off.
IP Address Display
To prevent the IP addressg from being displayed on the LAN
Standby screen, set this to Off.
List of Functions
70
Security menu
Sub-menu
Security
Sub-menu
Function
Encryption Key
1/Encryption Key
2/Encryption Key
3/Encryption Key
4
You can enter the key used for WEP encryption. Enter the key in
single-byte characters following instructions from the network
administrator for the network in which the projector
participates. The type of character and the number that can be
entered differ according to the WEP Encryption and Format
settings.
128Bit - ASCII: Single-byte alphanumerics, 13 characters.
64Bit - ASCII: Single-byte alphanumerics, 5 characters.
128Bit - HEX: 0 to 9 and A to F, 26 characters.
64Bit - HEX: 0 to 9 and A to F, 10 characters.
Authentication
Type
Set the WEP authentication type.
Open: Uses open system authentication.
Shared: Uses shared key authentication.
PSK
(This can only be set when WPA-PSK or WPA2-PSK are
selected from Security.)
You can enter a Pre-Shared Key (encrypted key) in single-byte
alphanumeric characters. Enter at least 8 and up to 32 characters.
Function
Select the security type from the items that are displayed.
When setting security, follow the instructions from the
administrator of the network system you are about to access.
WEP Encryption
You can set the encryption method for WEP encryption.
128Bit: Uses 128 (104) bit encoding.
64Bit: Uses 64 (40) bit encoding.
Format
You can set the input method for the WEP encryption key to
ASCII or HEX.
Key ID
You can select the WEP encryption ID key.
Type of security
When the optional wireless LAN unit is installed and being used in
Advanced connection mode, it is strongly recommended that you set
security. Select one of the following security methods.
• WEP
Data is encrypted with a code key (WEP key). This mechanism prevents
communication unless the encryption keys for the access point and the
projector match.
List of Functions
• WPA
This is an encryption standard that improves security which is a weak
point of WEP. Although there are multiple kinds of WPA encryption
methods, this projector uses TKIP and AES.
WPA also includes user authentication functions. WPA authentication
provides two methods: using an authentication server, or authenticating
between a computer and an access point without using a server. This
projector supports the latter method, without a server.
a
For setting details, follow the directions from the network
administrator of your network.
71
Wired LAN menu
List of Functions
Sub-menu
IP Settings
IP Address Display
72
Function
You can make settings related to the following addresses.
DHCPg: Set to On to configure the network using DHCP. If this
is set to On, you cannot set any more addresses.
IP Addressg: You can input the IP address assigned to the
projector. You can input a number from 0 to 255 in each field of
the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Maskg: You can input the subnet mask for the projector.
You can input a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Addressg: You can input the IP address for the gateway
for the projector. You can input a number from 0 to 255 in each
field of the address. However, the following gateway addresses
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
To prevent the IP address from being displayed on Network Info
in the Network menu and on the LAN Standby screen, set this to
Off.
s "Using the Mail Notification Function to Report Problems" p.111
Sub-menu
Function
Mail Notification
Set to On to send an email to the preset addresses when a problem
or warning occurs with a projector.
SMTP Server
You can input the IP addressg for the SMTP server for the
projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Port Number
You can input the port number for the SMTP server. The default
value is 25. You can input numbers between 1 to 65535.
Mail menu
When this is set, you receive an email notification if a problem or warning
occurs in the projector.
List of Functions
73
Sub-menu
Function
Address 1 Setting/Address 2
Setting/Address
3 Setting
You can input the email address of the destination to send the
notification email to. You can register up to three destinations.
You can enter up to 32 single-byte alphanumeric characters for
the email addresses.
The address for destination 1 is the mail notification sender's
address.
You can select the problems or warnings to be notified about by
email. When the selected problem or warning occurs in the
projector, an email is sent to the specified destination address
notifying that a problem or warning has occurred. You can select
multiple items from the displayed items.
Others menu
Sub-menu
Function
SNMP
Set to On to monitor the projector using SNMP.
To monitor the projector, you need to install the SNMP manager
program on your computer. SNMP should be managed by a
network administrator.
The default value is Off.
Trap IP Address
1/Trap IP Address 2
You can register up to two IP addresses for the SNMP trap
notification destination. You can enter a number from 0 to 255 in
each field of the address. However, the following IP addresses
cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x
is a number from 0 to 255)
Priority Gateway
You can set the priority gateway to a Wired LAN or Wireless
LAN.
List of Functions
74
Reset menu
Sub-menu
Function
AMX Device Discovery
When the projector is connected to a network, set this to On to
allow the projector to be detected by AMX Device
Discoveryg.Set this to Off if you are not connected to an
environment controlled with a controller from AMX or AMX
Device Discovery.
Crestron RoomView
Set this to On only when monitoring or controlling the projector
over the network using Crestron RoomView . Otherwise, set
this to Off.
s "About Crestron RoomView " p.114
When this is set to On, the following functions are not available.
• Web control
• Message Broadcasting (EasyMP Monitor Plug-in)
Resets all of the network settings.
®
®
Bonjour
Set this to On when connecting to the network using Bonjour.
See Apple's Web site for more information on the Bonjour
service.
http://www.apple.com/
Sub-menu
Reset network
settings.
Function
To reset all of the Network settings, select Yes.
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status
of the projector. Items that can be displayed vary depending on the source
currently being projected. Depending on the model used, some input
sources are not supported.
List of Functions
75
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.29
Sub-menu
Function
Status
This information is about errors that have occurred with
the projector.
It may be needed if service is required.
Serial Number
Displays the projector's serial number.
Event ID
Displays the application error log.
s "About Event ID" p.92
*
The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours
and above is displayed as "10H", "11H", and so on.
Reset Menu
Sub-menu
Function
Lamp Hours
You can display the cumulative lamp operating time*.
When it reaches the lamp warning time, the characters are
displayed in yellow.
Source
You can display the source name for the connected
equipment currently being projected.
Input Signal
You can display the content of Input Signal set in the
Signal menu according to the source.
Resolution
You can display the resolution.
Video Signal
You can display the settings for Video Signal in the Signal
menu.
Refresh Rate
You can display the refresh rateg.
Sync Info
You can display the image signal Information.
It may be needed if service is required.
Sub-menu
Reset All
Function
You can reset all items in the Configuration menu to their default
settings.
The following items are not reset to their defaults: Input Signal,
Zoom, User's Logo, all items for Network menus, Lamp Hours,
Language, and Password.
List of Functions
Sub-menu
Reset Lamp
Hours
76
Function
Clears the cumulative lamp hours use time. Reset this when you
replace the lamp.
Troubleshooting
This chapter describes how to identify problems and what to do if a problem is found.
Using the Help
78
If a problem occurs with the projector, the Help screen is displayed to assist
you by pressing the Help button. You can solve problems by answering the
questions.
a
c
Confirm the selection.
Using Remote Control
Using the Control Panel
Press the [Help] button.
The Help screen is displayed.
Using Remote Control
Using the Control Panel
Questions and solutions are displayed as shown on the screen below.
Press the [Help] button to exit the Help.
b
Select a menu item.
a
Using Remote Control
Using the Control Panel
See the following if the Help function does not provide a
solution to the problem.
s "Problem Solving" p.79
Problem Solving
79
If you are having a problem with the projector, first check the projector's indicators and see "Reading the Indicators".
See the following if the indicators do not show clearly what the problem might be.
s "When the Indicators Provide No Help" p.82
Reading the Indicators
The projector is provided with the following three indicators that indicate the operating status of the projector.
A Power indicator
Indicates the operating status.
Standby condition
When the [t] button is pressed in this condition, projection starts.
Preparing for network monitoring or cool down in progress
All buttons are disabled while the indicator is flashing.
Warming up
Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
The [t] button is disabled during warm-up.
Projecting
B Lamp indicator
C Temp indicator
Indicates the projection lamp status.
Indicates the internal temperature status.
See the following table for the status of indicators and how to resolve the problems.
Problem Solving
80
If all indicators are off, the power cable is not connected correctly or the power is not being supplied.
Sometimes, when the power cable is unplugged, the t indicator remains lit for a short period, but this is not a fault.
: Lit
Status
Cause
: Flashing
: Off
: Varies according to the projector status
Remedy or Status
Internal Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
Fan Error
Sensor Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
High Temp Error
(overheating)
The lamp turns off automatically and projection stops. Wait for approximately five minutes. After approximately five minutes the projector
switches to standby mode, so check the following two points.
• Check that the air filter and air exhaust vent are not blocked, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.94,"Replacing the Air Filter" p.99
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s "Extended Menu" p.64
Lamp Error
Lamp Failure
Check the following two points.
• Take out the lamp and check whether it is cracked.
s "Replacing the Lamp" p.96
• Clean the air filter.
s "Cleaning the Air Filter" p.94
Problem Solving
Status
81
Cause
Remedy or Status
If it is not cracked: Reinstall the lamp and turn on the power.
If the error continues: Replace the lamp with a new one and then turn on the power.
If the error continues: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest
address provided in the Epson Projector Contact List.
s Epson Projector Contact List
If it is cracked: Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be projected until
the lamp is replaced.)
s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s "Extended Menu" p.64
Auto Iris Error
Power Err.
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
High Temp Warning
(This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)
• Check that the air filter and air exhaust vent are not blocked, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.94, "Replacing the Air Filter" p.99
Replace Lamp
a
Replace it with a new lamp.
s "Replacing the Lamp" p.96
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may blow increases. Replace it with a new
lamp as soon as possible.
• See the following if the projector is not operating properly, even though the indicators are all showing normal.
s "When the Indicators Provide No Help" p.82
• If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or
the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
82
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a
solution, refer to the pages given for each problem.
Problems Relating to Images
sp.83
• No images appear
Projection does not start, the projection area is completely black,
or the projection area is completely blue.
sp.84
• Moving images are not displayed
Moving images played back from a computer appear black and
the images are not projected.
• Projection stops automatically
sp.84
• The message "Not supported" is displayed
sp.84
• The message "No Signal" is displayed
sp.84
• Images are fuzzy, out of focus, or distorted
sp.85
• Interference or distortion appear in images
sp.85
• The image is truncated (large) or small, or the aspect ratio is not
suitable
Only part of the image is displayed, or the height and width
ratios of the image are not correct.
sp.86
sp.87
• Image colors are not right
The whole image appears purplish or greenish, images are black
& white, or colors appear dull.
• Images appear dark
sp.87
Problems when Projection Starts
• The projector does not turn on
sp.88
Other Problems
• No sound can be heard or the sound is faint
sp.89
• No sound can be heard from the microphone
sp.89
• The remote control does not work
sp.90
• I want to change the language for messages and menus
sp.90
• Mail is not received even if an error occurs with the projector
sp.90
Problem Solving
83
Problems Relating to Images
No images appear
Check
Remedy
Did you press the [t] button?
Press the [t] button to turn the power on.
Are all of the indicators off?
The power cable is not connected correctly or power is not being supplied.
Connect the projector's power cable correctly.
s "From Installation to Projection" p.28
Check the breaker and so on to ensure power is being supplied.
Is A/V Mute active?
Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.44
Is the lens cover attached?
Remove the lens cover.
Are the Configuration menu settings correct?
Reset all of the settings.
s Reset - Reset All p.75
Is the image to be projected completely black?
(Only when projecting computer images)
Some input images, such as screen savers, may be completely black.
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.61
Is the USB cable connected correctly?
(Only when projecting USB Display)
Check that the USB cable is connected correctly. Reconnect it if it is not connected or not connected properly.
Is Windows Media Center displayed in full screen?
When Windows Media Center is displayed at full screen, you cannot project using USB Display or network connection.
(Only when projecting using USB Display or network connection) Reduce the screen size.
Is an application using the Windows DirectX function displayed? Applications using the Windows DirectX function may not display images correctly.
(Only when projecting using USB Display or network connection)
Problem Solving
84
Moving images are not displayed (only the moving image portion turns black)
Check
Is the computer's image signal being output to the LCD and the
monitor?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)
Remedy
Change the image signal from the computer to external output only. Check your computer's documentation, or contact
the computer's manufacturer.
Projection stops automatically
Check
Is Sleep Mode set to On?
Remedy
Press the [t] button to turn the power on. If you do not want to use Sleep Mode, change the setting to Off.
sExtended - Operation - Sleep Mode p.64
The message "Not supported" is displayed.
Check
Remedy
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.61
Do the image signal resolution and refresh rate correspond to the
mode?
(Only when projecting computer images)
See the documentation supplied with the computer for how to change the image signal resolution and refresh rate output
from the computer.
s "Supported Monitor Displays" p.122
The message "No Signal" is displayed.
Check
Remedy
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.
s "From Installation to Projection" p.28
Is the correct port selected?
Change the image by pressing the [Source Search] button on the remote control or the control panel.
s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.29
Problem Solving
85
Check
Remedy
Is the power of the connected computer or video equipment turned Turn the power on for the equipment.
on?
Are the image signals being output to the projector?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)
If the image signals are only being output to the computer's LCD monitor or accessory monitor, change the output so
that the image signals are also output externally. For some computer models, when the image signals are output
externally, they no longer appear on the LCD monitor or accessory monitor.
If the connection is made while the power of the projector or computer is already turned on, the Fn key (Function key)
that changes the computer's image signal to external output may not work. Turn the projector and computer off and then
back on again.
s "From Installation to Projection" p.28
s Computer's documentation
Images are fuzzy, out of focus, or distorted
Check
Remedy
Is the focus adjusted correctly?
Turn the focus ring to adjust the focus.
s "Correcting the Focus" p.38
Is the projector at the correct distance?
Is it projecting outside of the recommended projection distance range?
Setup within the recommended range.
s "Screen Size and Projection Distance" p.119
Is the Keystone adjustment value too large?
Lower the projection angle to reduce the amount of Keystone correction.
s "Adjusting the Image Position" p.37
Has condensation formed on the lens?
If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature
changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the
projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and
wait for the condensation to disappear.
Interference or distortion appear in images
Check
Is the image signal format setting correct?
(Only when projecting images from a video source)
Remedy
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.61
Problem Solving
86
Check
Remedy
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.
s "Connecting Equipment" p.18
Is an extension cable being used?
If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to
check if the cables you are using may be causing the problem.
Is the correct resolution selected?
(Only when projecting computer images)
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.122
s Computer's documentation
Are the Sync.g and Trackingg settings adjusted correctly?
(Only when projecting computer images)
Press the [Auto] button on the remote control or the [ ] button on the control panel to perform automatic adjustment.
If the images are not adjusted correctly even after performing automatic adjustment, you can also make adjustments
from the Configuration menu.
s Signal - Tracking, Sync. p.61
Is Transfer layered window selected?
(Only when projecting USB Display)
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then clear the
Transfer layered window checkbox.
The image is truncated (large) or small, or the aspect is not suitable
Check
Remedy
Is a wide-panel computer image being projected?
(Only when projecting computer images)
Change the setting according to the signal for the connected equipment.
s Signal - Resolution p.61
Is the image still being enlarged by E-Zoom?
Press the [Esc] button on the remote control to cancel E-Zoom.
s "Enlarging Part of the Image (E-Zoom)" p.46
Is the display position adjusted correctly?
(Only when projecting analog RGB signals input from the Computer1 or Computer2 port)
Press the [Auto] button on the remote control or the [
] button on the control panel to adjust the position.
You can also adjust the position from the Configuration menu.
s Signal - Position p.61
Is the computer set for dual display?
(Only when projecting computer images)
If dual display is activated in the Display Properties of the computer's Control Panel, only about half of the image on the
computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting.
s Computer video driver documentation
Problem Solving
87
Check
Is the correct resolution selected?
(Only when projecting computer images)
Remedy
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.122
s Computer's documentation
Image colors are not right
Check
Remedy
Do the input signal settings match the signals from the connected
device?
Change the following settings according to the signal for the connected equipment.
• When the image is from a device connected to the Computer1 or Computer2 port.
s Signal - Input Signal p.61
• When the image is from a device connected to the Video or S-Video port.
s Signal - Video Signal p.61
Is the image Brightness adjusted correctly?
Adjust the Brightness setting from the Configuration menu.
s Image - Brightness p.60
Are the cables connected correctly?
Check that all the cables required for projection are securely connected.
s "Connecting Equipment" p.18
Is the contrastg adjusted correctly?
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.60
Is color adjustment set to an appropriate value?
Adjust the Color Adjustment setting from the Configuration menu.
s Image - Color Adjustment p.60
Are the color saturation and tint adjusted correctly?
(Only when projecting images from a video source)
Adjust the Color Saturation and Tint settings from the Configuration menu.
s Image - Color Saturation, Tint p.60
Images appear dark
Check
Is the image brightness set correctly?
Remedy
Adjust the Brightness and Power Consumption settings from the Configuration menu.
s Image - Brightness p.60
s Settings - Power Consumption p.63
Problem Solving
88
Check
Remedy
Is the contrastg adjusted correctly?
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.60
Is it time to replace the lamp?
When the lamp is nearly ready for replacement, the images become darker and the color quality declines. Replace the
lamp with a new one.
s "Replacing the Lamp" p.96
Problems when Projection Starts
The projector does not turn on
Check
Remedy
Did you press the [t] button?
Press the [t] button to turn the power on.
Are all of the indicators off?
The power cable is not connected correctly or power is not being supplied.
Disconnect and then reconnect the power cable.
s "From Installation to Projection" p.28
Check the breaker and so on to ensure power is being supplied.
Do the indicators turn on and off when the power cable is touched? There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If this
does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Is the Control Panel Lock set to Full Lock?
Press the [t] button on the remote control. If you do not want to use Control Panel Lock, change the setting to Off.
s Settings - Control Panel Lock p.63
Is the remote receiver set correctly?
Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver p.63
Problem Solving
89
Other Problems
No sound can be heard or the sound is faint
Check
Remedy
Check that the audio/video cable is securely attached to both the
projector and audio source.
Disconnect the cable from the audio input port, and then reconnect the cable.
Is the volume adjusted to the minimum setting?
Adjust the volume so that sound can be heard.
s Settings - Volume p.63
s "Adjusting the Volume" p.38
Is the Mic Input Level set at the maximum?
Lower the Mic Input Level.
s Settings - Mic Input Level p.63
Is A/V Mute active?
Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.44
Is the audio cable's specification "No resistance"?
When using a commercially available audio cable, make sure it is labeled "No resistance".
Is it connected with an HDMI cable?
If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.
Is Output audio from the projector selected?
(Only when projecting USB Display)
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then select
Output audio from the projector.
Is the correct audio input selected?
Check the Audio Input from the configuration menu.
s Extended - Operation - Audio Input p.64
No sound can be heard from the microphone
Check
Remedy
Is the microphone connected correctly?
Disconnect the cable from the Mic port, and then reconnect the cable.
s "Connecting External Equipment" p.24
Is the microphone input volume turned down too low?
Adjust the microphone input volume so that sound can be heard.
s Settings - Mic Input Level p.63
Problem Solving
90
The remote control does not work
Check
Remedy
Is the remote control light-emitting area pointing towards the
remote receiver on the projector during operation?
Point the remote control towards the remote receiver during operation.
s "Remote control operating range" p.15
Is the remote control too far from the projector?
The operating range for the remote control is about 6 m.
s "Remote control operating range" p.15
Is direct sunlight or strong light from fluorescent lamps shining onto Set the projector up in a location where strong light does not shine onto the remote receiver. Or set the remote receiver to
the remote receiver?
Off from Remote Receiver in the Configuration menu.
s Settings - Remote Receiver p.63
Is the correct setting for the Remote Receiver selected?
Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver p.63
Are the batteries dead or have the batteries been inserted in the
wrong direction?
Insert new batteries in the correct direction.
s "Replacing the remote control batteries" p.15
I want to change the language for messages and menus
Check
Change the language setting.
Remedy
Adjust the Language setting from the Configuration menu.
s Extended - Language p.64
Mail is not received even if an error occurs with the projector
Check
Remedy
Is Standby Mode set to Communication On?
To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode from
the Configuration menu.
s Extended - Standby Mode p.64
Did a fatal abnormality occur and the projector come to a sudden
stop?
When the projector comes to a sudden stop, email cannot be sent.
If the abnormal state continues, contact your local dealer or the nearest address provided in the Epson Projector Contact
List.
s Epson Projector Contact List
Problem Solving
91
Check
Is power being supplied to the projector?
Remedy
Check that your electrical outlet or power source is functioning correctly.
Is the Mail Notification function set correctly in the Configuration An error notification email is sent according to the Mail settings in the Configuration menu. Check if it is set correctly.
menu?
s"Mail menu" p.72
About Event ID
92
Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local
dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Event ID
Cause
Remedy
0432
0435
Failed to startup EasyMP Network Projection.
Restart the projector.
0434
0482
0484
0485
Network communication is unstable.
Check the network communication status, and reconnect after waiting for a
while.
0433
Cannot play transferred images.
Restart EasyMP Network Projection.
0481
Communication was disconnected from the computer.
0483
04FE
EasyMP Network Projection ended unexpectedly.
Check the network communication status, and then restart the projector.
0479
04FF
A system error occurred in the projector.
Restart the projector.
0891
Cannot find an access point with the same SSID.
Set the computer, the access point, and the projector to the same SSID.
0892
The WPA/WPA2 authentication type does not match.
0893
The WEP/TKIP/AES encryption type does not match.
Check that the wireless LAN security settings are correct.
s Security p.70
0894
Communication was disconnected because the projector connected to an
unauthorized access point.
Contact your network administrator for more information.
0898
Failed to acquire DHCP.
Check that the DHCP server is operating correctly. If you are not using DHCP,
turn off the DHCP setting.
s Wireless LAN - IP Settings p.68
0899
Other communication errors
If restarting the projector or EasyMP Network Projection does not solve the
problem, contact your local dealer or the nearest address provided in the Epson
Projector Contact List.
s Epson Projector Contact List
Maintenance
This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.
Cleaning
You should clean the projector if it becomes dirty or if the quality of
projected images starts to deteriorate.
Attention
94
Attention
Do not rub the lens with harsh materials or subject the lens to shocks, as it
can easily become damaged.
Turn off the projector's power before cleaning.
Cleaning the Air Filter
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water containing
a small amount of neutral detergent, and then firmly wring the cloth dry
before using it to wipe the projector's surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the
projector's surface. The quality of the case may change or become discolored.
Cleaning the Lens
Use a commercially available cloth for cleaning glasses to gently wipe the
lens.
Warning
Do not use sprays that contain flammable gas to remove dirt and dust from the
lens. The projector may catch fire because of the high temperature of the lamp
inside the projector.
Clean the air filter and the air intake vent when the following message is
displayed.
"The projector is overheating. Make sure nothing is blocking the air vent,
and clean or replace the air filter."
Attention
• Dust collecting on the air filter may cause the internal temperature of the
projector to rise, leading to a malfunction or early deterioration of optical
parts. Clean the air filter immediately when the message is displayed.
• Do not rinse the air filter in water. Do not use detergents or solvents.
Cleaning
a
95
• If a message is frequently displayed, even after cleaning, it is time to
replace the air filter. Replace it with a new air filter.
s "Replacing the Air Filter" p.99
• It is recommended that you clean these parts at least once every
three months. Clean them more often than this if using the projector
in a particularly dusty environment.
Replacing Consumables
This section explains how to replace the lamp and the air filter.
Replacing the Lamp
Lamp replacement period
It is time to replace the lamp when:
• The following message is displayed.
"It is time to replace your lamp. Please contact your Epson projector
reseller or visit www.epson.com to purchase."
96
Attention
• The lamp replacement message is set to appear after the following time
periods in order to maintain the initial brightness and quality of the projected
images.
EB-435W/EB-430
When Power Consumption is set to Normal: About 3900 hours
When Power Consumption is set to ECO: About 5900 hours
EB-425W/EB-420
When Power Consumption is set to Normal: About 4900 hours
When Power Consumption is set to ECO: About 5900 hours
s Settings - Power Consumption p.63
• If you continue to use the lamp after the replacement period has passed, the
possibility that the lamp may blow increases. When the lamp replacement
message is displayed, replace the lamp with a new one as soon as possible,
even if it is still working.
• Do not repeatedly turn off the power and immediately back on. Turning the
power on and off frequently may shorten the lamp's operating life.
The message is displayed for 30 seconds.
• Depending on the individual characteristics of the lamp and the way it has
been used, the lamp may become darker or stop working before the message
is displayed. You should always have a spare lamp unit ready in case it is
needed.
• The lamp indicator flashes orange.
How to replace the lamp
The lamp can be replaced even when the projector is suspended from a wall
or ceiling.
• The projected image gets darker or starts to deteriorate.
Replacing Consumables
97
Warning
• When replacing the lamp because it has stopped working, there is a
possibility that the lamp may be cracked.When replacing the lamp of a
projector that has been installed on a wall or ceiling, assume that the lamp is
cracked and stand to the side of the lamp cover, not underneath it. Also,
remove the lamp cover gently.
• Never disassemble or modify a lamp. If a modified or disassembled lamp is
installed in the projector and used, it could cause a fire, electric shock, or an
accident.
Caution
Wait until the lamp has cooled down sufficiently before removing the lamp
cover. If the lamp is still hot, burns or other injuries may result. It takes
approximately one hour after the power has been turned off for the lamp to
sufficiently cool down.
a
After you turn off the projector's power and the confirmation
buzzer beeps twice, disconnect the power cable.
b
Wait until the lamp has sufficiently cooled down, and then remove
the lamp cover at the top of the projector.
Loosen the lamp cover fixing screw with the screwdriver supplied
with the new lamp unit or a Phillips (+) screwdriver. Then slide the
lamp cover straight forward and lift to remove it.
c
Loosen the two lamp fixing screws.
Replacing Consumables
d
Remove the old lamp by pulling the handle.
If the lamp is cracked, replace it with a new lamp, or contact your
local dealer for further advice.
s Epson Projector Contact List
98
e
Install the new lamp.
Insert the new lamp along the guide rail in the correct direction so
that it fits in place, push in firmly, and once it is fully inserted
tighten the two screws.
Replacing Consumables
99
Attention
• Make sure you install the lamp securely. If the lamp cover is removed, the
power turns off automatically as a safety precaution. If the lamp or the lamp
cover is not installed correctly, the power does not turn on.
• This product includes a lamp component that contains mercury (Hg). Please
consult your local regulations regarding disposal or recycling. Do not dispose
of it with normal waste.
Resetting the lamp hours
The projector records how long the lamp is on and a message and indicator
notify you when it is time to replace the lamp. After replacing the lamp,
make sure you reset the lamp hours from the Configuration menu.
s "Reset Menu" p.75
f
Attach the lamp cover.
a
Only reset the lamp hours after the lamp has been replaced. Otherwise,
the lamp replacement period will not be indicated correctly.
Replacing the Air Filter
Air filter replacement period
If the message is displayed frequently even though the air filter has been
cleaned, replace the air filter.
How to replace the air filter
The air filter can be replaced even when the projector is suspended from a
wall or ceiling.
Replacing Consumables
a
After you turn off the projector's power and the confirmation
buzzer beeps twice, disconnect the power cable.
b
Open the air filter cover.
c
100
d
Install the new air filter.
e
Close the air filter cover.
Press the tabs on the air filter cover and open the cover.
Remove the air filter.
Grip the tab in the center of the air filter, and pull the air filter
straight out.
Replacing Consumables
a
Dispose of used air filters properly in accordance with your local
regulations.
Material of the frame part: Polypropylene
Material of the filter part: Polypropylene
101
Appendix
Slideshow
103
Projecting Without a Computer (Slideshow)
By connecting a USB storage device such as a USB memory or a USB hard
disk to the projector, you can project the files stored on the device without
using a computer. This function is called Slideshow.
a
• You may not be able to use USB storage devices that incorporate
security functions.
• You cannot correct keystone distortion while projecting a Slideshow,
] and [
] buttons on the control
even if you press the [
panel.
a
• When connecting and using a USB-compatible hard disk, make sure
you connect the AC adaptor supplied with the hard disk.
• The projector does not support some file systems, so use media that
has been formatted in Windows.
• Format the media in FAT16/32.
Slideshow examples
Projecting images stored on USB storage
Specifications for files that can be projected using Slideshow
Type
File Type (Extension)
Notes
Image
.jpg
The following cannot be projected.
- CMYK color mode format
- Progressive format
- Images with a resolution greater than 8192x8192
Due to the characteristics of JPEG files, images may
not be projected clearly if the compression ratio is
too high.
.bmp
Cannot project images with a resolution greater
than 1280x800.
.gif
• Cannot project images with a resolution greater
than 1280x800.
• Cannot project animated GIFs.
.png
Cannot project images with a resolution greater
than 1280x800.
s "Projecting the selected image" p.105
s "Projecting image files in a folder in sequence (Slideshow)" p.106
Slideshow operating methods
Although the following steps are explained based on the remote control,
you can perform the same operations from the control panel.
Starting Slideshow
a
Change the source to USB.
s "Switching to the Target Image Using the Remote Control"
p.30
Slideshow
b
104
Connect the USB storage device or digital camera to the projector.
s "Connecting USB Devices" p.22
Slideshow starts and the file list screen is displayed.
a
• JPEG files are displayed as thumbnails (file contents are displayed
as small images).
[
• Other files or folders are displayed as icons as shown in the
following table.
Icon
*
File
Icon
• You can also insert a memory card into a USB card reader and then
connect the reader to the projector. However, some commercially
available USB card readers may not be compatible with the
projector.
• If the following screen (Select Drive screen) is displayed, press the
], [
], [ ], and [ ] buttons to select the drive you want to
use, and then press the [
] button.
File
JPEG files*
BMP files
GIF files
PNG files
When it cannot be displayed as a thumbnail, it is displayed as an icon.
• To display the Select Drive screen, position the cursor on Select
Drive at the top of the file list screen, and then press the [ ]
button.
Projecting images
a
Use the [
], [
], [ ], and [ ] buttons to select the file or
folder you want to project.
Slideshow
105
b
a
Press the [
] button.
Stopping Slideshow
To close Slideshow, disconnect the USB device from the USB port on the
projector. For devices such as digital cameras or hard disks, turn off the
device and then remove it from the projector.
] button.
The selected image is displayed.
When a folder is selected, the files in the selected folder are
displayed. To return to the previous screen, position the cursor on
Back to Top and press the [ ] button.
Projecting the selected image
Attention
Do not disconnect the USB storage device while it is being accessed.
Slideshow may not operate correctly.
Rotating images
You can rotate the played images in 90˚ increments. The rotating function
is also available during Slideshow.
a
Start Slideshow.
The file list screen is displayed.
s "Starting Slideshow" p.103
a
] or [
If not all of the files and folders are displayed on the current
screen, press the []] button on the remote control, or position
the cursor on Next Page at the bottom of the screen and press
the [ ] button.
To return to the previous screen, press the [[] button on the
remote control, or position the cursor on Previous Page at the
top of the screen and press the [ ] button.
b
While projecting, press the [
Play images, or run Slideshow.
Slideshow
b
106
Press the [
], [
], [ ], and [ ] buttons to select the image file
you want to project.
Projecting image files in a folder in sequence (Slideshow)
You can project the image files in a folder in sequence, one at a time. This
function is called Slideshow. Use the following procedure to run
Slideshow.
a
a
To change files automatically when you run Slideshow, set Screen
Switching Time from Option in Slideshow to anything other than No.
The default setting is 3 seconds.
Start Slideshow.
The file list screen is displayed.
s "Starting Slideshow" p.103
c
Press the [
] button.
b
Use the [
c
Select Slideshow at the bottom right of the file list screen, and
then press the [ ] button.
The image is displayed.
], [
], [ ], and [ ] buttons to position the cursor
over the folder for the Slideshow that you want to run, and then
press the [ ] button.
Slideshow starts, and the image files in the folder are automatically
projected in sequence, one at a time.
a
d
Press the [ ][ ] buttons to move to the next or previous
image file.
Press the [Esc] button to return to the file list screen.
When the last file is projected, the file list is displayed again
automatically. If you set Continuous Play to On in the Option
window, projection starts again from the beginning when it reaches
the end.
s "Image file display settings and Slideshow operation settings"
p.107
You can proceed to the next screen, return to the previous screen, or
stop playback while projecting a Slideshow.
Slideshow
a
107
If Screen Switching Time on the Option screen is set to No, files do
not change automatically when you select Play Slideshow. Press the
[ ] button, the [
] button, or the []] button to continue to the next
file.
You can use the following functions when projecting an image file with
Slideshow.
• Freeze
s "Freezing the Image (Freeze)" p.44
• A/V Mute
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.44
• E-Zoom
s "Enlarging Part of the Image (E-Zoom)" p.46
Image file display settings and Slideshow operation settings
You can set the file display order and Slideshow operations on the Option
screen.
a
b
Press the [
], [
], [ ] and [ ] buttons to position the cursor
over the folder where you want to set display conditions, and then
press the [Esc] button. Select Option from the submenu displayed,
then press the [ ] button.
When the following Option screen is displayed, set each of the
items.
Enable settings by positioning the cursor on the target item and
pressing the [ ] button.
The following table shows the details for each item.
c
Display Order
You can select to display the files in Name Order or Date
Order.
Sort Order
You can select to sort the files In Ascending or In
Descending order.
Continuous
Play
You can set whether to repeat the Slideshow.
Screen Switching Time
You can set the time for a single file to be displayed in Play
Slideshow. You can set a time between No (0) to 60
Seconds. When you set No, auto play is disabled.
Effect
You can set the screen effects when changing slides.
When you have finished making settings, use the [
], [
], [ ],
and [ ] buttons to position the cursor over OK, and then press
the [
] button.
The settings are applied.
If you do not want to apply the settings, position the cursor on
Cancel, and then press the [ ] button.
Monitoring and Controlling
About EasyMP Monitor
EasyMP Monitor lets you carry out operations such as checking the status
of multiple Epson projectors that are connected to a network at a computer
monitor, and controlling the projectors from the computer.
You can download EasyMP Monitor from the following Web site.
http://www.epson.com
The following provides brief descriptions of the monitoring and control
functions that can be carried out using EasyMP Monitor.
• Registering projectors for monitoring and control
Projectors on the network can be searched for automatically, and you can
then select which projectors you want to register from the projectors that
are detected.
You can register target projectors by entering their IP addresses.
• Registered projectors can also be assigned to groups so that they can
be monitored and controlled in groups.
• Monitoring the status of registered projectors
You can check the power status (ON/OFF) for projectors and problems or
warnings that require attention by using the icons.
You can select groups of projectors or a single projector and then check
the cumulative lamp operating time or information such as input sources,
problems, and warnings for the projectors.
• Controlling registered projectors
Projectors can be selected in groups or as single projectors, and you can
then carry out operations for the selected projectors such as turning the
power on and off and switching their input sources.
You can use Web Control functions to change the settings in the
projector's configuration menu.
If there are certain control actions which are carried out regularly at
particular times or on particular days, you can use Timer Settings to
register timer settings.
108
• Mail Notification settings
You can set e-mail addresses to which notifications are sent if a status
that requires attention, such as a problem, occurs with a registered
projector.
• Sending messages to registered projectors
You can use the Message Broadcasting plugin for EasyMP Monitor to
send JPEG files to registered projectors.
Download the Message Broadcasting plugin from the Web site address
provided at the beginning of this chapter.
Changing Settings Using a Web Browser (Web
Control)
By using the Web browser of a computer connected to the projector on a
network, you can set the projector's functions and control the projector.
This function allows you to perform setup and control operations remotely.
In addition, since you can use the computer's keyboard, entering characters
required for the setup is easier.
Use Microsoft Internet Explorer 6.0 or later as the Web browser. If using a
Mac OS, use Safari or Firefox.
a
If you set Standby Mode to Communication On, you can use a Web
browser to make settings and perform control even if the projector is
in standby mode (when the power is off).
s Extended - Standby Mode p.64
Projector setup
In a Web browser, you can set items that are usually set in the projector's
Configuration menu. The settings are reflected in the Configuration menu.
There are also items that can only be set in a Web browser.
Monitoring and Controlling
Items in the Configuration menu that cannot be set by a Web browser
• Settings menu - Keystone - Quick Corner
• Settings menu - Pointer Shape
• Settings menu - Pattern
• Settings menu - User Button
• Extended menu - User's Logo
• Extended menu - Language
• Extended menu - Operation - High Altitude Mode
• Reset menu - Reset All and Reset Lamp Hours
The settings for items on each menu are the same as the projector's
Configuration menu.
s "Configuration Menu" p.56
Items that can only be set with a Web browser
• SNMP Community Name
• Monitor Password
109
b
Enter the IP address of the projector in the address input box of
the Web browser, and press the Enter key on the computer's
keyboard.
The Web Control screen is displayed.
When Web Control Password is set in the Network menu from the
projector's Configuration menu, the password entry screen is
displayed.
Displaying the Web Remote screen
The Web Remote function allows you to perform projector remote control
operations with a Web browser.
a
b
Display the Web Control screen.
c
The Web Remote screen is displayed.
Click Web Remote.
Displaying the Web Control screen
Use the following procedure to display the Web Control screen.
Make sure the computer and projector are connected to the network. Use
Advanced when connecting via a Wireless LAN.
a
a
If your Web browser is set up to connect via a proxy server, the Web
Control screen cannot be displayed. To display Web Control, you need
to make settings so that a proxy server is not used for a connection.
Start a Web browser on the computer.
Monitoring and Controlling
110
Name
F [Page] buttons
[Up] [Down]
Function
Changes pages in files such as PowerPoint files when using
the following projection methods.
• When using the Wireless Mouse function
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.47
• When using USB Display
s "Projecting with USB Display" p.30
• When connecting to a network
When projecting images using Slideshow, pressing these
buttons displays the previous/next image file.
Name
G [Source Search]
button
Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.29
H [LAN] button
Changes to the images projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to
that image.
s "Switching to the Target Image Using the Remote
Control" p.30
I [USB] button
Each time the button is pressed, it cycles through the
following images:
• USB Display
• Images from the device connected to the USB(TypeA)
port
s "Switching to the Target Image Using the Remote
Control" p.30
J [Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.38
Function
A [t] button
Turns the projector power on or off.
s "From Installation to Projection" p.28
B [Computer] button
Each time you press the button, the input changes between
images from the Computer1 port and the Computer2
port.
C [Video] button
Each time the button is pressed, the image cycles through
Video, S-Video, and HDMI ports.
D [Freeze] button
Pauses or resumes image playback.
s "Freezing the Image (Freeze)" p.44
E [A/V Mute] button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.44
Monitoring and Controlling
Using the Mail Notification Function to Report
Problems
When you set Mail Notification, notification messages are sent to the preset
email addresses when a problem or warning occurs with a projector. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Mail - Mail Notification p.72
a
• Up to a maximum of three notification destinations (addresses) can
be registered, and notification messages can be sent to all three
destinations at once.
• If a projector develops a critical problem and suddenly stops
working, it may not be able to send a message notifying an operator
of the problem.
• Controlling is possible if Standby Mode is set to Communication
On, even if the projector is in standby state (when the power is
off).
s Extended - Standby Mode p.64
111
• Internal error
• Fan related error
• Sensor error
• Lamp timer failure
• Lamp out
• Internal temperature error
• High-speed cooling in progress
• Lamp replacement notification
• No-signal
No Signal is input to the projector. Check the connection status or check
that the power for the signal source is turned on.
• Auto Iris Error
• Power Err. (Ballast)
See the following to deal with problems or warnings.
s "Reading the Indicators" p.79
Reading Error Notification Mail
When the Mail Notification function is set to On and a problem or warning
occurs in the projector, the following email will be sent.
Subject: EPSON Projector
Line 1: The name of the projector where the problem occurred
Line 2: The IP address set for the projector where the problem has
occurred.
Line 3 and on: Details of the problem
The details of the problem are listed line by line. The main message
contents are listed below.
Management Using SNMP
By setting SNMP to On in the Configuration menu, notification messages
are sent to the specified computer when a problem or warning occurs. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Others - SNMP p.73
Monitoring and Controlling
a
112
Item
• SNMP should be managed by a network administrator or someone
who is familiar with the network.
• To use the SNMP function to monitor the projector, you need to
install the SNMP manager program on your computer.
• The managing function using SNMP cannot be used via wireless
LAN in Quick connection mode.
• Up to two destination IP addresses can be saved.
ESC/VP21 Commands
You can control the projector from an external device using ESC/VP21.
A/V Mute ON/OFF
When the power ON command is transmitted to the projector, the power
turns on and it enters warm-up mode. When the projector's power has
turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and
returns a ":", and then accepts the next command.
SOURCE 21
Component
SOURCE 24
HDMI
SOURCE 30
Video
SOURCE 41
S-Video
SOURCE 42
USB Display
SOURCE 51
USB
SOURCE 52
LAN
SOURCE 53
On
MUTE ON
Off
MUTE OFF
For more details, contact your local dealer or the nearest address provided
in the Epson Projector Contact List.
s Epson Projector Contact List
If the command being processed terminates abnormally, an error message is
output and a ":" is returned.
Cable layouts
The main contents are listed below.
Serial connection
Item
Signal selection
RGB
Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
Command list
Power ON/OFF
Command
Command
On
PWR ON
Off
PWR OFF
Computer1
Computer2
Auto
SOURCE 1F
RGB
SOURCE 11
Component
SOURCE 14
Auto
SOURCE 2F
• Connector shape: D-Sub 9-pin (male)
Monitoring and Controlling
113
• Projector input port name: RS-232C
<At the projector>
<At the computer>
About PJLink
PJLink Class1 was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for
controlling network-compatible projector's as part of their efforts to
standardize projector control protocols.
The projector complies with the PJLink Class1 standard established by the
JBMIA.
See the following for more information on network settings related to
PJLink.
s "Network Menu" p.66
<At the projector>
(PC serial cable)
<At the computer>
It complies with all commands except for the following commands defined
by PJLink Class1, and agreement was confirmed by the PJLink standard
adaptability verification.
URL:http://pjlink.jbmia.or.jp/english/
• Non-compatible commands
Function
Signal Name
Function
GND
Signal wire ground
TD
Transmit data
RD
Receive data
Mute settings
PJLink Command
Image muting set
AVMT 11
Audio muting set
AVMT 21
• Input names defined by PJLink and corresponding projector sources
Source
Communications protocol
•
•
•
•
•
Default baud rate setting: 9600 bps
Data length: 8 bit
Parity: None
Stop-bit: 1 bit
Flow control: None
PJLink Command
Computer1
INPT 11
Computer2
INPT 12
Video
INPT 21
S-Video
INPT 22
HDMI
INPT 32
USB
INPT 41
Monitoring and Controlling
114
Source
PJLink Command
LAN
INPT 52
USB Display
INPT 53
• Monitoring and control with application software
You can use Crestron RoomView Express or Crestron RoomView
Server Edition provided by Creston to monitor devices in the system, to
communicate with the help desk, and to send emergency messages. See
the following Web site for details.
http://www.crestron.com/getroomview
®
®
• Manufacturer name displayed for "Manufacture name information query"
®
EPSON
This manual describes how to perform operations on your computer using
a Web browser.
• Model name displayed for "Product name information query"
EB-420/CS500XN/PowerLite 420
EB-425W/CS500WN/PowerLite 425W
EB-435W/CS520WN/PowerLite 435W
EB-430/CS510XN/PowerLite 430
a
®
About Crestron RoomView
®
Crestron RoomView is an integrated control system provided by
Crestron . It can be used to monitor and control multiple devices
connected on a network.
®
• You can only enter single-byte alphanumeric characters and symbols.
• The following functions cannot be used while using Crestron
RoomView .
s "Changing Settings Using a Web Browser (Web Control)"
p.108
Message Broadcasting (EasyMP Monitor plug-in)
®
• Controlling is possible if Standby Mode is set to Communication
On, even if the projector is in standby state (when the power is
off).
s Extended - Standby Mode p.64
The projector supports the control protocol, and can therefore be used in a
system built with Crestron RoomView .
®
Visit the Crestron
®
®
Web site for details on Crestron RoomView .
http://www.crestron.com
Operating a projector from your computer
Displaying the operation window
®
The following provides an overview of Crestron RoomView .
Check the following before carrying out any operations.
• Remote operation using a Web browser
You can operate a projector from your computer just like using a remote
control.
• Make sure the computer and projector are connected to the network.
When communicating with a wireless LAN, connect in Advanced
connection mode.
s "Wireless LAN menu" p.68
• Set Crestron RoomView to On from the Network menu.
s Network - Others - Crestron RoomView p.73
Monitoring and Controlling
a
b
115
Start a Web browser on the computer.
Enter the IP address of the projector in the address field of the
Web browser, and press the Enter key on the keyboard.
Button
Function
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.44
A/V Mute
The operation window is displayed.
B Switch to the image from the selected input source. To display input sources that
are not shown on the screen, click (a) or (b) to scroll up or down.
You can change the source name if necessary.
Using the operation window
C You can perform the following operations when you click the buttons. To display
buttons that are not shown on the screen, click (c) or (d) to scroll left or right.
Button
Function
Freeze
Pauses or resumes image playback.
s "Freezing the Image (Freeze)" p.44
Contrast
You can adjust the difference between light and dark in
the images.
Brightness
You can adjust the image brightness.
Color
You can adjust the color saturation for the images.
Sharpness
You can adjust the image sharpness.
Zoom
Click the [z] button to enlarge the image without
changing the projection size. Click the [x] button to
reduce an image that was enlarged with the [z] button.
Click the [ ], [ ], [ ], or [ ] button to change the
position of an enlarged image.
s "Enlarging Part of the Image (E-Zoom)" p.46
A You can perform the following operations when you click the buttons.
Button
Function
Power
Turns the projector power on or off.
Vol-/Vol+
Adjusts the volume.
D [
], [
], [
], or [
] buttons have the same effects as [
][
][ ][ ]
buttons on the remote control. You can perform the following operations when
you click the other buttons.
Monitoring and Controlling
Button
116
Function
OK
Performs the same operation as the [
remote control.
s "Remote Control" p.12
Menu
Displays and closes the Configuration menu.
Auto
If clicked while projecting analog RGB signals from
Computer1 port or Computer2 port, automatically
optimizes the image by adjusting the Tracking, Sync.,
and Position.
Search
Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.29
Esc
Performs the same operation as the [Esc] button on the
remote control.
s "Remote Control" p.12
] button on the
E You can perform the following operations when you click the tabs.
Tab
®
B Projector
The following items can be set.
Item
Function
Contact IT Help
Displays the Help Desk window. Used to send messages
to, and receive messages from, the administrator using
Crestron RoomView Express.
Info
Displays information on the projector that is currently
connected.
Tools
A Crestron Control
Make settings for Crestron central controllers.
Projector Name
Enter a name to differentiate the projector that is
currently connected from other projectors on the
network. (The name can contain up to 15 single-byte
alphanumeric characters.)
Location
Enter an installation location name for the projector
that is currently connected on the network. (The name
can contain up to 32 single-byte alphanumeric
characters and symbols.)
Assigned To
Enter a user name for the projector. (The name can
contain up to 32 single-byte alphanumeric characters
and symbols.)
®
Changes settings in the projector that is currently
connected. See the next section.
Using the tools window
The following window is displayed when you click the Tools tab on the
operation window. You can use this window to change settings in the
projector that is currently connected.
Function
Monitoring and Controlling
Item
117
Function
DHCP
Select the Enabled check box to use DHCP. You cannot
enter an IP address if DHCP is enabled.
IP Address
Enter the IP address to assign to the currently connected
projector.
Subnet Mask
Enter a subnet mask for the currently connected
projector.
Default Gateway
Enter the gateway address for the currently connected
projector.
Send
Click this button to confirm the changes made to the
Projector.
C Admin Password
Select the Enabled check box to require a password to open the Tools window.
The following items can be set.
Item
Function
New Password
Enter the new password when changing the password to
open the Tools window. (The name can contain up to 26
single-byte alphanumeric characters.)
Confirm
Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send
Click this button to confirm the changes made to the
Admin Password.
D User Password
Select the Enabled check box to require a password to open the operation window
on the computer.
The following items can be set.
Item
Function
New Password
Enter the new password when changing the password to
open the operation window. (The name can contain up
to 26 single-byte alphanumeric characters.)
Confirm
Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send
Click this button to confirm the changes made to the
User Password.
Optional Accessories and Consumables
The following optional accessories and consumables are available. Please
purchase these products as and when needed.The following list of optional
accessories and consumables is current as of: August 2011. Details of
accessories are subject to change without notice.
118
Ceiling mount* ELPMB23
Use when installing the projector on a ceiling.
Ceiling pipe (450 mm) * ELPFP13
Ceiling pipe (700 mm) * ELPFP14
Use when installing the projector on a high ceiling.
Optional Accessories
Document Camera ELPDC06/ELPDC11
Special expertise is required to suspend the projector. Contact your local dealer
or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
*
Use when projecting images such as books, OHP documents, or slides.
Computer cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
This is the same as the computer cable supplied with the projector.
Computer cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
These are extension cables for when the computer cable supplied with the
projector is too short.
Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male^3)
Use to connect a Component Videog source.
Wireless LAN unit ELPAP07
Use when connecting the projector to a computer wirelessly and projecting.
Quick Wireless Connection USB Key ELPAP08
Use when you want to quickly establish one-to-one connection between the
projector and a computer with Windows installed.
Wall mount * ELPMB27
Use this arm type fitting when installing the projector on a wall.
Interactive Unit ELPIU03
Use when operating the computer screen on the projection surface.
Consumables
Lamp unit (for EB-425W/EB-420) ELPLP60
Lamp unit (for EB-435W/EB-430) ELPLP61
Use as a replacement for a used lamp.
Air filter ELPAF36
Use as a replacement for a used air filter.
Screen Size and Projection Distance
119
Unit: cm
Projection Distance (For EB-430/EB-420)
4:3 Screen Size
*
A
B
Minimum (Wide) to Maximum
(Tele)
Minimum
(Wide)
50"
100x76
55 - 75
6
60"
120x91
66 - 90
8
70"
140x105
78 - 106
9
80"
160x120
89 - 122
10
90"
180x135
101*
12
100"
200x150
112*
13
108"
219x165
122*
14
Project using Wide (maximum zoom).
Unit: cm
16:9 Screen Size
A Projection distance
B Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a wall or ceiling)
C Center of lens
*
A
B
Minimum (Wide) to Maximum
(Tele)
Minimum
(Wide)
50"
110x62
60 - 82
17
60"
130x75
72 - 99
21
70"
150x87
85 - 116
24
80"
180x100
98*
28
90"
200x110
110*
31
99"
219x123
121*
34
Project using Wide (maximum zoom).
Screen Size and Projection Distance
120
Unit: cm
Projection Distance (For EB-435W/EB-425W)
4:3 Screen Size
*
A
B
Minimum (Wide) to Maximum
(Tele)
Minimum
(Wide)
50"
100x76
58 - 79
9
60"
120x91
70 - 96
11
70"
140x105
82 - 112
13
80"
160x120
94*
14
90"
180x135
107*
16
102"
207x155
121*
18
Project using Wide (maximum zoom).
Unit: cm
16:9 Screen Size
A Projection distance
B Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a wall or ceiling)
C Center of lens
*
A
B
Minimum (Wide) to Maximum
(Tele)
Minimum
(Wide)
60"
130x75
63 - 87
14
70"
150x87
74 -101
16
80"
180x100
85 - 116
19
90"
200x110
97*
21
100"
220x120
108*
23
113"
250x141
122*
26
Project using Wide (maximum zoom).
Unit: cm
16:10 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
Minimum
(Wide)
55"
115x72
56 - 77
9
60"
130x81
61 - 84
9
Screen Size and Projection Distance
16:10 Screen Size
*
121
A
B
Minimum (Wide) to Maximum
(Tele)
Minimum
(Wide)
70"
150x94
72 - 99
11
80"
170x110
83 - 113
13
90"
190x120
94*
14
100"
220x130
105*
16
116"
251x157
122*
18
Project using Wide (maximum zoom).
Supported Monitor Displays
122
Component Video
Supported Resolutions
Computer signals (analog RGB)
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (480i)
60
720x480
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (576i)
50
720x576
VGA
60/72/75/85
640x480
SDTV (480p)
60
720x480
SVGA
56/60/72/75/85
800x600
SDTV (576p)
50
720x576
XGA
60/70/75/85
1024x768
HDTV (720p)
50/60
1280x720
WXGA
60
1280x768
HDTV (1080i)
50/60
1920x1080
60
1360x768
60/75/85
1280x800
WXGA+
60/75/85
1440x900
SXGA
70/75/85
1152x864
Signal
Refresh Rate (Hz)
Resolution (dots)
60/75/85
1280x1024
TV (NTSC)
60
720x480
60/75/85
1280x960
TV (SECAM)
50
720x576
60/75
1400x1050
TV (PAL)
50/60
720x576
60
1680x1050
UXGA
60
1600x1200
MAC13”
67
640x480
MAC16”
75
832x624
MAC19”
75
1024x768
59
1024x768
75
1152x870
SXGA+
WSXGA+*1,
MAC21”
2
*1 EB-435W/EB-425W only
*2 Only compatible when Wide is selected as the Resolution from the
Configuration menu.
Images may also be projected when signals other than the above are input.
However, some functions may be limited.
Composite video
Input signal from the HDMI port
Signal
Refresh Rate (Hz)
Resolution (dots)
VGA
60
640x480
SVGA
60
800x600
XGA
60
1024x768
WXGA
60
1280x800
60
1280x960
60
1280x1024
SXGA+
60
1400x1050
UXGA
60
1600x1200
SXGA
Supported Monitor Displays
123
Signal
Refresh Rate (Hz)
Resolution (dots)
SDTV (480i/480p)
60
720x480
SDTV (576i/576p)
50
720x576
HDTV (720p)
50/60
1280x720
HDTV (1080i)
50/60
1920x1080
HDTV (1080p)
24/30/50/60
1920x1080
Specifications
124
Projector General Specifications
EB-435W
Product name
EB-430
EB-425W
345 (W) x 105 (H) x 277 (D) mm (not including raised section)
Dimensions
0.59" Wide
LCD panel size
0.55"
0.59" Wide
1,024,000
WXGA (1280 (W)x 800 (H)
dots)x 3
Resolution
786,432
XGA (1024 (W) x 768 (H)
dots)x 3
1,024,000
WXGA (1280 (W)x 800 (H)
dots)x 3
Focus adjustment
Manual
Zoom adjustment
Digital (1-1.35)
UHE lamp, 230 W Model No.: ELPLP61
Lamp
786,432
XGA (1024 (W) x 768 (H)
dots)x 3
UHE lamp, 200 W Model No.: ELPLP60
16 W
Max. audio output
1
Speaker
100 to 240V AC ±10%, 50/60 Hz 3.4 to 1.5 A
100 to 240V AC ±10%, 50/60 Hz 3.0 to 1.3 A
100 to 120 V area
Operating: 332 W
Standby power consumption (Communication On): 6.8 W
Standby power consumption (Communication Off): 0.28 W
Operating: 294 W
Standby power consumption (Communication On): 6.2 W
Standby power consumption (Communication Off): 0.29 W
220 to 240 V area
Operating: 316 W
Standby power consumption (Communication On): 7.3 W
Standby power consumption (Communication Off): 0.37 W
Operating: 283 W
Standby power consumption (Communication On): 6.8 W
Standby power consumption (Communication Off): 0.39 W
Power supply
Altitude 0 to 2,286 m
Operating altitude
Operating temperature
+5 to +35°C (No condensation)
Storage temperature
-10 to +60°C (No condensation)
Approx. 3.9 kg
Mass
Connectors
0.55"
Polysilicon TFT active matrix
Display method
Power consumption
EB-420
Approx. 3.9 kg
Approx. 3.8 kg
Approx. 3.8 kg
Computer1 port
1
Mini D-Sub15-pin (female)
Computer2 port
1
Mini D-Sub15-pin (female)
Specifications
125
Video port
1
RCA pin jack
S-Video port
1
Mini DIN 4-pin
Audio1 port
1
Stereo mini pin jack
Audio2 port
1
Stereo mini pin jack
Audio-L/R port
1
RCA pin jack x 2 (L-R)
Mic port
1
Stereo mini pin jack
Audio Out port
1
Stereo mini pin jack
Monitor Out port
1
Mini D-Sub15-pin (female)
HDMI port
1
HDMI (Audio is only supported by PCM)
USB(TypeA) port *
1
USB connector (Type A)
USB(TypeB) port *
1
USB connector (Type B)
USB port
(dedicated Wireless LAN unit)
1
USB connector (Type A)
LAN port
1
RJ-45
RS-232C port
1
Mini D-Sub 9-pin (male)
* Supports USB 2.0. However, the operation of all USB compatible devices is not guaranteed.
Specifications
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Angle of tilt
If you use the projector tilted at an angle of more than 15˚ it could be damaged and cause an accident.
126
Specifications
127
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit tested
and found to be compliant with the standards. Records maintained continue
to reflect the equipment being produced can be expected to be within the
variation accepted, due to quantity production and testing on a statistical
basis as required by 47CFR 2.909. Operation is subject to the following two
conditions : (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesired operation.
Trade Name:
EPSON
Type of Product:
LCD Projector
Model:
H447C/H448C/H449C/H469C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television
reception. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause interference to radio
and television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this
device and may cause interference levels which exceed the limits established
by the FCC for this equipment. It is the responsibility of the user to obtain
and use a shielded equipment interface cable with this device. If this
equipment has more than one interface connector, do not leave cables
connected to unused interfaces. Changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate the
equipment.
Appearance
A
B
128
Center of lens
Measurements from the center of the lens to the wall mount plate fixing points or
the ceiling mount fixing points.
Units: mm
Glossary
129
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
AMX Device Discovery
AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.
Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).
See the AMX Web site for more details.
URL http://www.amx.com/
Aspect Ratio
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
Component Video
A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or
Pr).
Composite video
A method that combines the video signal into a luminance component and a color component for transmission down a single cable.
Contrast
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to
make them appear softer. Adjusting this particular property of an image is called "contrast adjustment".
DHCP
An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP addressg to equipment connected to a network.
Gateway Address
This is a server (router) for communicating across a network (subnet) divided according to subnet maskg.
HDCP
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting
digital signals sent over DVI and HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital images protected by
HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption.
HDTV
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
• Vertical resolution of 720p or 1080i or greater (p = Progressiveg, i = Interlaceg)
• Screen aspect ratiog of 16:9
Interlace
Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.
Images are more likely to flicker because one frame is displayed every other line.
IP Address
A number to identify a computer connected to a network.
Progressive
Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount
of flicker in images decreases because the volume of information has doubled compared with an interlace system.
SDTV
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTVg HighDefinition Television.
SNMP
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and
computers connected to a TCP/IP network.
Glossary
130
sRGB
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by
computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source
to sRGB.
SSID
SSID is identification data for connecting to another device on a wireless LAN. Wireless communication is possible between devices that correspond
to SSID.
Subnet Mask
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
SVGA
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
S-Video
A method that separates the video signal into a luminance component (Y) and a color component (C).
SXGA
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
Sync.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called
Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
Tracking
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If tracking is not carried
out correctly, wide vertical stripes appear in the signal.
Trap IP Address
This is the IP addressg for the destination computer used for error notification in SNMP.
VGA
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
XGA
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
General Notes
131
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by the
purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising
from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
About Notations
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
Microsoft
®
®
®
®
®
®
®
®
®
®
®
®
®
®
Windows 98 operating system
Windows Me operating system
Windows 2000 operating system
Windows XP Professional operating system
Windows XP Home Edition operating system
Windows Vista operating system
Windows 7 operating system
In this guide, the operating systems above are referred to as "Windows 98",
"Windows Me", "Windows 2000", "Windows XP", "Windows Vista", and
"Windows 7". Furthermore, the collective term Windows may be used to
refer to Windows 98, Windows Me, Windows 2000, Windows XP,
Windows Vista, and Windows 7, and multiple versions of Windows may be
referred to as, for example, Windows 98/Me/2000/XP/Vista, with the
Windows notation omitted.
Mac
Mac
Mac
Mac
OS
OS
OS
OS
X
X
X
X
10.3.x
10.4.x
10.5.x
10.6.x
In this guide, the operating systems above are referred to as "Mac OS X
10.3.9", "Mac OS X 10.4.x", "Mac OS X 10.5.x", and "Mac OS X 10.6.x".
Furthermore, the collective term "Mac OS" is used to refer to them.
General Notice:
IBM, DOS/V, and XGA are trademarks or registered trademarks of International
Business Machines Corp.
Macintosh, Mac, Mac OS, and iMac are trademarks of Apple Inc.
Microsoft, Windows, Windows NT, Windows Vista, PowerPoint, and Windows logo
are trademarks or registered trademarks of Microsoft Corporation in the United States
and/or other countries.
WPA and WPA2 are registered trademarks of Wi-Fi Alliance.
HDMI and High-Definition Multimedia Interface are the trademarks or registered
™
™
trademarks of HDMI Licensing LLC.
PJLink trademark is a trademark applied for registration or is already registered in
Japan, the United States of America and other countries and areas.
Other product names used herein are also for identification purposes only and may be
trademarks of their respective owners. Epson disclaims any and all rights in those
marks.
©SEIKO EPSON CORPORATION 2011. All rights reserved.
Index
132
A
A/V Mute ...................................................... 44
Abs. Color Temp. ........................................ 60
Air exhaust vent ............................................. 8
Air filter replacement period ..................... 99
Aspect ...................................................... 40, 62
Auto Iris .................................................. 39, 61
Auto Setup .................................................... 61
Crestron RoomView ................................. 114
Cross .............................................................. 46
Direct Power On .......................................... 65
Display ........................................................... 65
Display Background .................................... 65
Display Order ............................................. 107
Display settings .......................................... 107
Distance ...................................................... 119
Document Camera .................................... 118
Dynamic ........................................................ 38
I
Image menu .................................................. 60
Indicators ...................................................... 79
Info menu ..................................................... 74
Input Signal ............................................ 62, 75
IP Address ..................................................... 72
E
C
Ceiling ..................................................... 17, 65
Ceiling mount fixing points ....................... 10
Cleaning ........................................................ 94
Cleaning the air filter and air intake vent
.......................................................................... 94
Cleaning the projector's surface ................ 94
Color Adjustment ........................................ 61
Color Mode ............................................ 38, 60
Color Saturation .......................................... 60
Computer port ............................................... 9
Configuration menu .................................... 57
Connection mode ........................................ 69
Consumables .............................................. 118
Continuous ................................................. 107
Contrast ........................................................ 60
Control panel ............................................... 11
Control Panel Lock ............................... 54, 63
H/V-Keystone .............................................. 34
HDMI port ...................................................... 9
HDMI Video Range .................................... 62
Help function ............................................... 78
High Altitude Mode .................................... 65
How to replace the air filter ........................ 99
How to replace the lamp ............................. 96
D
B
Basic menu .................................................... 68
Blackboard .................................................... 39
Brightness ..................................................... 60
H
EasyMP Monitor ....................................... 108
Email address ............................................... 73
ESC/VP21 ................................................... 112
Extended menu ............................................ 64
E-Zoom ......................................................... 46
K
Keystone ........................................................ 63
L
F
Focus ring ....................................................... 8
Foot adjust lever ............................................. 8
Freeze ............................................................. 44
Front ........................................................ 17, 65
Front adjustable foot ..................................... 8
Full Lock ....................................................... 54
G
Gateway Address ................................... 69, 72
Lamp cover ..................................................... 8
Lamp Hours .................................................. 75
Lamp indicator ............................................. 79
Lamp replacement period .......................... 96
Language ....................................................... 66
M
Mail Notification ................................. 72, 111
Mail Notification menu .............................. 72
Message Broadcasting ............................... 108
Messages ....................................................... 65
Mic Input Level ............................................ 63
Index
133
Progressive .................................................... 62
Projection ...................................................... 65
Projector Keyword ....................................... 68
Projector Name ............................................ 68
Projector setup ........................................... 108
Monitor displays ........................................ 122
Mouse pointer .............................................. 47
N
Network Configuration ..............................
Network information ..................................
Network menu .............................................
Noise Reduction ...........................................
66
66
66
62
O
Sleep Mode ................................................... 65
Slideshow ............................................ 103, 106
SMTP Server ................................................. 72
SNMP .......................................................... 111
Soft keyboard ................................................ 67
Source ............................................................ 75
Source Search ......................................... 11, 29
Specifications ............................................. 124
Sports ............................................................. 38
sRGB .............................................................. 38
SSID ............................................................... 69
Standby Microphone ................................... 65
Standby Mode .............................................. 65
Startup Screen .............................................. 65
Storage temperature .................................. 124
Subnet Mask ........................................... 69, 72
Supported monitor displays ..................... 122
S-Video port ................................................. 10
Sync Info ....................................................... 75
Sync. ............................................................... 62
Q
Quick Corner ............................................... 63
R
Operating temperature ............................. 124
Operation ...................................................... 65
Optional accessories .................................. 118
Overheating .................................................. 80
Reading mail ............................................... 111
Rear .......................................................... 17, 65
Rear feet ........................................................ 11
Rear screen .................................................... 17
Refresh Rate .................................................. 75
Remote control ............................................ 12
Remote receiver ............................................. 8
Replacing batteries ....................................... 15
Reset All ........................................................ 75
Reset Lamp Hours ....................................... 76
Reset menu ............................................. 74, 75
Resetting the lamp operating time ............ 99
Resolution ..................................................... 75
Rotating images ......................................... 105
P
Part names and functions ............................. 8
Password protect .......................................... 52
Password protect sticker ............................. 53
Pattern ........................................................... 64
Photo ............................................................. 38
PJLink .......................................................... 113
PJLink Password .......................................... 68
Pointer ........................................................... 45
Pointer Shape ............................................... 63
Port Number ................................................ 72
Position ......................................................... 62
Power Consumption ................................... 63
Power indicator ............................................ 79
Power inlet ...................................................... 9
Power On Protect ........................................ 52
Presentation ......................................... 38, 103
Problem solving ........................................... 79
T
Temp indicator ............................................
Theatre ..........................................................
Tint ................................................................
Tracking ........................................................
S
Screen size ................................................... 119
Screen switching time ............................... 107
Security menu .............................................. 70
Select Drive ................................................. 104
Settings menu ............................................... 63
Sharpness ...................................................... 60
Signal menu .................................................. 61
79
38
60
61
U
USB(TypeA) port ........................................... 9
USB(TypeB) port ........................................... 9
User Button .................................................. 64
User Pattern .................................................. 50
User's Logo ................................................... 48
Index
User's Logo Protect ...................................... 52
V
Video port ....................................................... 9
Video Signal ........................................... 62, 75
Volume .......................................................... 63
W
Web browser .............................................. 108
Web Control ............................................... 109
Web Control Password ............................... 68
Web Remote ............................................... 109
Whiteboard ................................................... 39
Wired LAN menu ........................................ 71
Wireless LAN menu .................................... 68
Wireless LAN Power ................................... 68
Wireless LAN system .................................. 69
Wireless mouse function ............................ 47
Z
Zoom ............................................................. 63
134