Part Names and Functions
① Infrared Remote Receiver
② Zoom Ring
③ Focus Ring
④ Projection Lens
Front
CAUTION
Do not cover the light beam in front of the lens. High
temperature from light beam may damage the lens.
⑤ Lens Cap
(See page 62 for attaching.)
CAUTION
①
⑨
Back
⑦
②③④
⑧
⑤
⑨
Do not turn on a projector with lens cap attached. High
temperature from light beam may damage lens cap and
result in fire hazard.
⑨
⑩⑪
⑫
⑥ Speaker
⑦ Exhaust Vents
CAUTION
Hot air is exhausted from the exhaust vent. Do not put
heat-sensitive objects near this side.
⑬
⑥
⑧ Lamp Cover
⑨ Air Intake Vents
⑩ Terminals and Connectors
⑪ Top Controls and Indicators
⑫ LAN Connection Terminal
⑬ Power Cord Connector
⑭ Filter Covers
⑮ Adjustable Feet
Bottom
⑭
Note:
⑫ LAN Connection Terminal is for the Network function.
Refer to the owner’s manual of “Network Set-up and
Operation”.
⑮
8
Kensington Security Slot
This slot is for a Kensington lock used to deter theft of
the projector.
*Kensington is a registered trademark of ACCO Brands
Corporation.
Part Names and Functions
Rear Terminal
④
⑩
③
⑨
⑧
①
②
⑦
① LAN Connection Terminal
Connect the LAN cable (refer to the owner’s manual
of "Network Set-up and Operation").
② COMPUTER IN 1 / COMPONENT IN
Connect output signal from a computer, RGB scart
21-pin video output or component video output to
this terminal(pp.14,16).
③ COMPUTER IN 2 / MONITOR OUT
– Connect computer output to this terminal (p.14).
– This terminal can be used to output the incoming
analog RGB and Component signal from
COMPUTER IN 1/COMPONENT IN terminal to the
other monitor (pp.14,16).
④ AUDIO OUT (VARIABLE)
Connect an external audio amplifier to this jack
(pp.14-16).
This terminal outputs sound from AUDIO IN terminal
(⑦ or ⑨).
⑤ S-VIDEO IN
Connect the S-VIDEO output signal from video
equipment to this jack (p.15).
⑥
⑤
⑥ CONTROL PORT
When controlling the projector with RS-232 C,
connect the control equipment to this connector
with the serial control cable.
⑦ AUDIO IN
Connect the audio output signal from video
equipment connected to ⑤ or ⑧ to this jack.
For a mono audio signal (a single audio jack),
connect it to the L (MONO) jack (p.15).
⑧ VIDEO IN
Connect the composite video output signal to
this jack (p.15).
⑨ COMPUTER AUDIO IN 1
Connect the audio output (stereo) from a
computer or video equipment connected to ② to
this jack. (pp14, 16).
⑩ COMPUTER AUDIO IN 2 (MIC IN)
Connect the audio output (stereo) from a
computer or video equipment connected to ③ to
this jack. Or connect the MIC to the this jack
(pp14, 16).
9
Part Names and Functions
Top Control
⑨
⑤
⑧
④
⑦
③
②
⑥
①
① SELECT button
–Execute the selected item (p.21).
–Expand or compress the image in the Digital zoom
mode (p.36).
⑦ AUTO SETUP button
Execute the setting of Auto setup (includes Input
search, Auto PC adj. and Auto Keystone functions)
in the setting menu. (pp.23, 47).
② POINT▲▼◄► (VOLUME –/+) buttons
–Select an item or adjust the value in the On-Screen
Menu (p.21).
–Pan the image in the Digital zoom +/- mode (p.36).
–Adjustthevolumelevel(Point◄►buttons)(p.24).
⑧ WARNING indicator
–Lights red when the projector detects an abnormal
condition.
–Blinks red when the internal temperature of the
projector exceeds the operating range (pp.60, 70).
③ INPUT button
Select an input source (pp.27-28, 38-39).
④ ON/STAND–BY button
Turn the projector on or off (pp.18-20).
⑤ POWER indicator
–Lights red when the projector is in stand-by mode.
–Lights green during operations.
–Blinks green in the Power management mode
(p.51).
⑥ MENU button
Open or close the On-Screen Menu (p.21).
10
⑨ LAMP REPLACE indicator
Lights yellow when the projection lamp reaches its
end of life (pp.63, 70).
Part Names and Functions
Remote Control
① ON/STAND-BY button
Turn the projector on or off. (pp.18-20)
② AUTO SET button
Execute the setting of Auto setup (includes Input search, Auto
PC adj. and Auto Keystone functions) in the setting menu.
(pp.23, 47)
③ COMPUTER 1/2 buttons
Select the COMPUTER 1 or COMPUTER 2 input source. (pp.27-28, 39)
②
①
⑤ S-VIDEO button
Select the S-VIDEO input source. (p.38)
③
④
⑤
⑳
⑲
⑥
⑦
⑱
⑧
⑰
⑨
⑯
⑮
⑭
⑩
⑪
⑫
④ VIDEO button
Select the VIDEO input source. (p.38)
⑬
⑥ Point ▲▼◄► buttons
– Select an item or adjust the value in the On-Screen Menu. (p.21)
– Pan the image in the Digital zoom +/- mode. (p.36)
⑦ SCREEN button
Select a screen mode. (pp.26, 35, 44)
⑧ MENU button
Open or close the On-Screen Menu. (p.21)
⑨ FREEZE button
Freeze the picture on the screen. (p.25)
⑩ NO SHOW button
Temporarily turn off the image on the screen. (p.26)
⑪ D.ZOOM ▲▼ buttons
Zoom in and out the images. (pp.25, 36)
⑫ VOLUME +/- buttons
Adjust the volume level. (p.24)
⑬ MUTE button
Mute the sound. (p.24)
⑭ IMAGE button
Select the image mode. (pp.26, 33, 41)
⑮ P-TIMER button
Operate the P-timer function. (pp.26, 52)
⑯ LAMP button
Select a lamp mode. (pp.25, 54)
⑰ INFO. button
Operate the information function. (pp.25, 59)
⑱ KEYSTONE button
Correct keystone distortion. (pp.23, 37, 45)
⑲ SELECT button
– Execute the selected item. (p.21)
– Expand or compress the image in Digital zoom mode. (p.36)
⑳ COMPONENT button
Select the COMPONENT input source. (p.39)
Note:
To ensure safe operation, please observe the following precautions:
– Do not bend, drop, or expose the remote control to moisture or heat.
– For cleaning, use a soft dry cloth. Do not apply benzene, thinner,
spray, or any chemical material.
11
Part Names and Functions
Remote Control Battery Installation
1
Open the battery
compartment lid.
2
Install new batteries
into the compartment.
3
Replace the
compartment lid.
Two AAA size batteries
For correct polarity
(+ and –), be sure
battery terminals are
in contact with pins in
compartment.
To ensure safe operation, please observe the following precautions :
Use two (2) AAA or LR03 type alkaline batteries.
Always replace batteries in sets.
Do not use a new battery with a used battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture or heat.
Do not drop the remote control.
If the battery has leaked on the remote control, carefully wipe the case clean and install new batteries.
Risk of an explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to the instructions or your local disposal rule or guidelines.
Remote Control Operating Range
Point the remote control toward the projector (Infrared
Remote Receiver) when pressing the buttons. Maximum
operating range for the remote control is about 16.4'(5 m)
and 60 degrees in front of the projector.
16.4'
(5 m)
30°
30°
Remote control
Remote Control Code
The 2 different remote control codes (Code 1–Code 2) are
assigned to this projector. Switching the remote control
codes prevents interference from other remote controls
when several projectors or video equipment next to each
other are operated at the same time. Change the remote
control code for the projector first before changing that for
the remote control. See "Remote control" in the Setting
Menu on page 54.
Press and hold the MENU and IMAGE buttons for more
than five seconds to switch between the Code 1 and Code
2. The initial code is set to Code 1.
12
MENU button
IMAGE button
Installation
Positioning the Projector
For projector positioning, see the figures below. The projector should be set perpendicularly to the plane of the
screen.
Note:
•Thebrightnessintheroomhasagreatinfluenceonpicturequality.Itisrecommendedtolimitambient
lighting in order to obtain the best image.
•Allmeasurementsareapproximateandmayvaryfromtheactualsizes.
41.8' (12.7 m)
34.8' (10.6 m)
300
23.2' (7.1 m)
17.4' (5.3 m)
200
250
11.6' (3.5 m)
150
4.6' (1.4 m)
100
40
167
125
83
Screen Size
(W x H) mm
4 : 3 aspect ratio
40"
100"
150"
200"
300"
813 x 610
2032 x 1524
3048 x 2286
4064 x 3048
6096 x 4572
Zoom (max)
4.6' (1.4 m)
11.6' (3.5 m)
17.4' (5.3 m)
23.2' (7.1 m)
34.8' (10.6 m)
Zoom (min)
5.5' (1.7 m)
13.9' (4.2 m)
20.9' (6.4 m)
27.8' (8.5 m)
41.8' (12.7 m)
Adjustable Feet
Projection angle can be adjusted up to 12.0 degrees with
the adjustable feet.
Lift the front of the projector and press the feet lock latches
on both side of the projector.
Release the feet lock latches to lock the adjustable feet and
rotate the adjustable feet to a proper height and tilt.
Keystone distortion can be adjusted automatically with the
Auto setup function or manually by using the remote control
or the menu operation (see pages 23, 37, 45).
Feet Lock Latches
Adjustable Feet
13
Installation
Connecting to a Computer
Cables used for connection
•VGACables(MiniD-sub15pin)*
•AudioCables
(*One cable is supplied; other cables are not supplied with the projector.)
External Audio Equipment
VGA
cable
Audio Input
Audio cable
(stereo)
Monitor Output
This terminal is
switchable. Set up
the terminal as either
Computer input or
Monitor output.
(See Page 51.)
AUDIO OUT
(stereo)
Monitor Input
VGA
cable
Monitor Output
Audio Output
VGA
cable
Audio cable
(stereo)
COMPUTER MONITOR
IN 2
OUT
COMPUTER IN 1 /
COMPONENT IN
COMPUTER 1/
COMPUTER 2
AUDIO IN (PC or MIC)
Note:
•WhentheMICfunctionissettoOff in the Sound menu, the MIC function is disabled. (p 24)
•WhenMIC is set to On in Sound Menu, COMPUTER AUDIO IN 1, COMPUTER AUDIO IN 2 / MIC IN and
AUDIO IN(L/R) terminals can be connected at the same time. At this time, COMPUTER AUDIO IN 2 termianl
as MIC input. (p 24)
•InputsoundtotheCOMPUTERAUDIOIN1,COMPUTERAUDIOIN2/MICINterminalswhenusingthe
COMPUTER IN 2 / MONITOR OUT and the COMPUTER IN 1/ COMPONENT IN terminal as input.
•WhentheAUDIOOUTisplugged-in,theprojector'sbuilt-inspeakerisnotavailable.
•When the cable is of the longer variety, it is advisable to use the COMPUTER IN 1 / COMPONENT IN and
not the COMPUTER IN 2/ MONITOR OUT.
Unplug the power cords of both the projector and external equipment from the AC outlet before connecting cables.
14
Installation
Connecting to Video Equipment
Cables used for connection
•VideoandAudioCable(RCAx3)
•S-VIDEOCable
•AudioCable
(Cables are not supplied with the projector. )
External Audio Equipment
Audio Input
Audio cable
(stereo)
AUDIO OUT (stereo)
Video and Audio Output
(Video) (L) (R)
Video and audio cable
VIDEO AUDIO IN
Note:
When the AUDIO OUT is plugged-in, the projector's builtin speaker is not available.
S-Video Output
S-Video cable
S-VIDEO
Unplug the power cords of
both the projector and external
equipment from the AC outlet
before connecting cables.
15
Installation
Connecting to Component Video Equipment
Cables used for connection
•AudioCables
•Scart-VGACable
•VGACable
•ComponentCable
•Component-VGACable
(Cables are not supplied with this projector.)
External Audio Equipment
Audio Input
Audio Output Monitor Input
RGB Scart
21-pin Output
Component Video Output
(Y, Pb/Cb, Pr/Cr)
Component
cable
Audio
cable
(stereo)
VGA cable
Scart-VGA
cable
Audio cable
(stereo)
ComponentVGA cable
COMPUTER
AUDIO IN 1
COMPUTER IN 2 /
MONITOR OUTPUT
COMPUTER IN 1/ COMPONENT IN
AUDIO OUT
(stereo)
Note:
•When theAUDIO OUT is plugged-in, the projector's
built-in speaker is not available.
•Seepage73fororderingoptionalcables.
16
Unplug the power cords of
both the projector and external
equipment from the AC outlet
before connecting cables.
Installation
Connecting the AC Power Cord
This projector uses nominal input voltages of 100-240 V AC
and it automatically selects the correct input voltage. It is
designed to work with single-phase power systems having a
grounded neutral conductor. To reduce the risk of electrical
shock, do not plug into any other type of power system.
If you are not sure of the type of power being supplied,
consult your authorized dealer or service center.
Connect the projector with all peripheral equipment before
turning the projector on.
Connect the AC power cord
(supplied) to the projector.
CAUTION
The AC outlet must be near this equipment and must be
easily accessible.
Note:
Unplug the AC power cord when the projector is not
in use. When this projector is connected to an outlet
with the AC power cord, it is in Stand-by mode and
consumes a little electric power.
NOTE ON THE POWER CORD
AC power cord must meet requirement of the country where you use the projector.
Confirm the AC plug type with the chart below and proper AC power cord must be used.
If supplied AC power cord does not match your AC outlet, contact your sales dealer.
Projector side
AC outlet side
For the U.S.A. and Canada
For Continental Europe
For the U.K.
Ground
Ground
To power cord
connector on your
projector.
To the AC outlet.
(120 V AC)
To the AC outlet.
(200 - 240 V AC)
To the AC outlet.
(200 - 240 V AC)
17
Basic Operation
Turning On the Projector
1
Complete peripheral connections (with a computer,
VCR, etc.) before turning on the projector.
2
Connect the projector’s AC power cord into an AC
outlet. The POWER indicator lights red. Open the lens
cap (see pages 8, 62).
3
Press the ON/STAND-BY button on the top control or
on the remote control. The POWER indicator lights
green and the cooling fans start to operate. The
preparation display appears on the screen and the
countdown starts.
4
5
After the countdown, the input source that was
selected the last time and the lamp control status icon
(see page 54) appear on the screen.
If there is no signal input when start on the projector,
or the current signal is missed while operating the
projector, the Video/PC selection window will be
displayed on the screen, please move the pointer to
input source desired by pressing the Point ▲▼ buttons
and press the SELECT button. And then follow the
input signal guidance window to correct the signal and
connection.
16
The preparation display will disappear
after 30 seconds.
Selected Input Source and Lamp Control
Video
Lamp control status
(See page 54 for Lamp control status.)
Note:
The Filter warning and Lamp replacement
icons may appear on the screen depending
on the usage state of the projector.
PC Selection
Project Video
If the projector is locked with a PIN code, PIN code
input dialog box will appear. Enter the PIN code as
instructed on the next page.
Project Computer
Cancel
Guidance for PC Input
Video Selection
Note:
•WhentheLogoselectfunctionissettoOff, the logo will
not be shown on the screen (p.48).
•When Countdown off or Off is selected in the Display
function, the countdown will not be shown on the screen
(p.48).
•WhentheInputSearchfunctionissettoOn2, the input
signal will be searched automatically (p.47)
•When Off is selected in the Display function, the Video/
PC selection window and the input signal guidance
window are not shown on the screen. (p.48)
18
ProjectVideo
Video
Project
Project Computer
Cancel
Guidance for Video Input
Basic Operation
Enter a PIN code
Use the Point ▲▼ buttons to enter a number. Press the
Point ► button to fix the number and move the red frame
pointer to the next box. The number changes to “ ”. If you
fixed an incorrect number, use the Point ◄ button to move
the pointer to the number you want to correct, and then
enter the correct number.
Repeat this step to complete entering a four-digit number.
PIN Code Input Dialog Box
After the OK icon disappears,
you can operate the projector.
After entering the four-digit number, move the pointer to Set.
Press the SELECT button so that you can start to operate
the projector.
If you entered an incorrect PIN code, PIN code and the
number (
) will turn red for a moment. Enter the
correct PIN code all over again.
What is PIN code?
PIN (Personal Identification Number) code is a security
code that allows the person who knows it to operate the
projector. Setting a PIN code prevents unauthorized use of
the projector.
A PIN code consists of a four-digit number. Refer to the PIN
code lock function in the Setting Menu on pages 55-56 for
locking operation of the projector with your PIN code.
CAUTION ON HANDLING PIN CODE
If you forget your PIN code, the projector can no
longer be started. Take a special care in setting
a new PIN code; write down the number in a
column on page 76 of this manual and keep it
on hand. Should the PIN code be missing or
forgotten, consult your dealer or service center.
Note:
•IfthePINcodenumberisnotenteredwithinthree
minutes after the PIN code dialog box appears, the
projector will be turned off automatically.
•The“1234”issetastheinitialPINcodeatthefactory.
19
Basic Operation
Turning Off the Projector
1
Press the ON/STAND-BY button on the top control or
on the remote control, and Power off? appears on the
screen.
2
Press the ON/STAND-BY button again to turn off the
projector. The POWER indicator starts to blink red, and
the cooling fans keep running. (You can select the level
of fans’ quietness and speed. See “Fan” on page 56.)
At this time, you can unplug the AC power cord even if
the fans are still running.
3
Power off? disappears after 4 seconds.
When the projector has cooled down enough, the
POWER indicator stops blinking and you can turn on
the projector.
TO MAINTAIN THE LIFE OF THE LAMP, ONCE
YOU TURN THE PROJECTOR ON, WAIT AT
LEAST FIVE MINUTES BEFORE TURNING IT
OFF.
DO NOT OPERATE THE PROJECTOR
CONTINUOUSLY WITHOUT REST.
CONTINUOUS USE MAY RESULT IN
SHORTENING THE LAMP LIFE. TURN OFF THE
PROJECTOR AND LET IT STAND FOR ABOUT
AN HOUR IN EVERY 24 HOURS.
Note:
•When the Direct on function is set to On, the projector
will be turned on automatically by connecting the AC
power cord to an AC outlet (p.51).
•Therunningspeedofcoolingfansischangedaccording
to the temperature inside the projector.
•Donotputtheprojectorinacasebeforetheprojectoris
cooled enough.
•IftheWARNINGindicatorblinksorlightsred,see
“WARNING indicator” on page 60.
•WhilethePOWERindicatorisblinking,thelampisbeing
cooled down and the projector cannot be turned on. Wait
until the POWER indicator stops blinking to turn on the
projector again.
•For assisting the cooling fans' operation, the projector
is equipped with a large capacitor. While the projector
is operating, the capacitor charges electricity. When
disconnecting the AC plug from AC outlet, cooling fans
start to run 1 minute until the capacitor is discharged.
•The projector can be turned on after the POWER
indicator turns red. The waiting time to restart will be
shortened when the normal power-off processing for fan
cooling is completed, compared with the time the AC
power cord is immediately unplugged after the poweroff.
20
Direct OFF Function
You can disconnect the power cord from the
wall outlet or turn off the breaker even during
projection without pressing the ON/STAND-BY
button.
Note:
When using the Direct OFF function, you
can not restart the projector immediately
after the power is disconnected. If the
external power supply is suddenly cut
off, the fans stop immediately. The lamp
remains high temperature and needs to be
cooled.
Basic Operation
How to Operate the On-Screen Menu
The projector can be adjusted or set via the On-Screen
Menu. The menus have a hierarchical structure, with
a main menu that is divided into submenus, which are
further divided into other submenus. For each adjustment
and setting procedure, refer to respective sections in this
manual.
1
Press the MENU button on the top control or the
remote control to display the On-Screen Menu.
2
Use the Point ▲▼ buttons to highlight or select a main
menu item. Press the Point ► or the SELECT button
to access the submenu items. (The selected item is
highlighted in orange.)
3
Use the Point ▲▼ buttons to select the desired
submenu item and press the SELECT button to set or
access the selected item.
4
Use the Point ▲▼◄► buttons to adjust the setting or
switch between each option and press the SELECT
button to activate it and return to the submenu.
5
Press the Point ◄ button to return to the main menu.
Press the MENU button to exit the On-Screen Menu.
Top Control
POINT buttons
(arrowhead)
SELECT button
MENU button
Remote Control
POINT buttons
(arrowhead)
SELECT button
MENU button
On-Screen Menu
Point ► or
SELECT
button
The currently set item is
marked.
The selected item is
highlighted in orange.
Point ◄
button
21
Basic Operation
Menu Bar
For detailed functions of each menu, see “Menu Tree” on pages 68-69.
Main Menu
Sub-Menu
1
2
3
4
5
6
7
8
9
1 Input
Used to select an input source from Computer 1, Computer 2, Video or S-video. (pp.27-28,38-39).
2 PC adjust
Select Auto PC adj., Fine sync, Total dots, Horizontal, Vertical, Current mode, Clamp, Display area H, Display area V,
Reset, Mode free and Store to adjust the parameters to match with the PC input signal format (pp.30-32).
3 Image select
For both of computer and Video sources, used to select an image mode from among Dynamic, Standard, Real, Cinema,
Blackboard(Green), Colorboard and Image 1 - 4 (pp.33, 41).
4 Image adjust
For computer source, used to adjust computer image [Contrast, Brightness, Color temp., White balance (R/G/B),
Sharpness and Gamma] (pp.34-35).
For Video source, used to adjust picture image [Contrast, Brightness, Color, Tint, Color temp., White balance (R/G/B),
Sharpness, Gamma, Noise reduction and Progressive] (pp.42-43).
5 Screen
For computer source, used to adjust size of the image [ Normal, Full, Wide (16:9), Zoom, True, Custom, Custom adj.,
Digital zoom +, Digital zoom -, Keystone, Ceiling, Rear and Reset] (pp.35-37).
For Video source, used to set size of image [Normal, Full, Wide (16:9), Zoom, Custom, Custom adj., Keystone, Ceiling,
Rear and Reset] (pp.44-45).
6 Sound
Used to adjust the volume or mute the sound or set configurations to the MIC functions (p.24).
7 Setting
Used to set the projector’s operating configurations (pp.46-58).
8 Information
Display the input source information: Input, H-sync freq., V-sync freq., Screen, Language, Lamp status, Lamp counter,
Power management, Security, Remote control, SERIAL NO. and Total power savings (p.59).
9 Network
See owner’s manual of “Network Set-up and Operation”.
Guide
The key operation is displayed.
22
Basic Operation
Zoom and Focus Adjustment
Rotate the Zoom Ring to zoom in and out.
Rotate the Focus Ring to adjust the focus of the image.
Focus Ring
Zoom Ring
Auto Setup Function
Auto setup function is provided to automatically execute the setting of Auto setup (includes Input search, Auto
PC adj. and Auto Keystone functions) in the setting menu by just pressing the AUTO SETUP button on the
top control or the AUTO SET button on the remote control. Refer to page 47 for the setting of the Auto setup
function.
Notes:
Top Control
•AutoKeystonecorrectsverticaldistortiononly;itdoes
AUTO SETUP button
not correct horizontal distortion.
•AutoKeystonecannotworkwhenCeilingfeatureisset
to On in the Screen Size Adjustment menu (pp.37, 45).
•Perfect correction of the image distortion cannot be
POINT▲▼ buttons
ensured with the Auto setup function. If the distortion
cannot be corrected properly by pressing the AUTO
SETUP or AUTO SET button, adjust manually by
pressing the KEYSTONE button on the remote control
Remote Control
or selecting Keystone in the Screen Size Adjustment
menu (pp.37, 45).
AUTO SET button
•Fine sync, Total dots, Horizontal and Vertical position
of some computers cannot be fully adjusted with
the Auto PC Adjustment function. When the image
is not provided properly with this operation, manual
adjustments are required (pp.31-32).
POINT ▲▼ buttons
Keystone Correction
If a projected picture still has keystone distortion after
pressing the AUTO SETUP button on the top control or the
AUTO SET button on the remote control, correct the image
manually as follows:
Press the KEYSTONE button on the remote control. The
Keystone dialog box appears. Use the Point ▲▼ buttons to
correct keystone distortion. The keystone adjustment can be
stored (see pages 37, 45).
Reduce the upper width
with the Point ▲ button.
Reduce the lower width
with the Point ▼ button.
KEYSTONE button
•Thewhitearrowsindicatethatthereisno
correction.
•Aredarrowindicatesthedirectionofcorrection.
•Anarrowdisappearsatthemaximumcorrection.
•If you press the KEYSTONE button on the
remote control once more while the keystone
dialog box is being displayed, the keystone
adjustment will be canceled.
•Theadjustablerangeislimiteddependingonthe
input signal.
23
Basic Operation
Sound Adjustment
Direct Operation
Top Control
VOLUME+/buttons
Volume
Press the VOLUME+/– buttons on the top control or on the
remote control to adjust the volume. The volume dialog box
appears on the screen for a few seconds.
Remote Control
Mute
Press the MUTE button on the remote control to select On
to temporarily turn off the sound. To turn the sound back
on, press the MUTE button again to select Off or press the
VOLUME +/– buttons. The Mute function is also effective for
the AUDIO OUT jack.
VOL+ button
MUTE button
VOL- button
Menu Operation
1
2
Press the MENU button to display the On-Screen Menu.
Use the Point ▲▼ buttons to select Sound. Press the
Point ► button or the SELECT button to access the
submenu items.
Approximate level
of the volume.
Volume Dialog Box
Use the Point ▲▼ buttons to select the desired
submenu item and press the SELECT button to access
the selected item.
Volume
Press the Point ► button to turn up the volume; press the
Point◄buttontoturndownthevolume.
Mute
Press the SELECT button to switch the mute function On/
Off. When the sound is turned off, On is displayed. Press
the VOLUME +/– buttons again to turn the sound back on.
Press the MUTE button to set the
Mute function On or Off. The dialog
box disappears after 4 seconds.
Sound Menu
MIC
Use the Point ▲▼ buttons to switch the MIC function
On/Off, and then press the SELECT button. When On is
selected, the synthesis volume (MIC and RCA) is output.
MIC gain
Press the Point ► button to turn up the MIC mixing gain;
PressthePoint◄buttontoturndowntheMICmixinggain.
Standby MIC out
When switch the Standby MIC out function On and in
Standby mode out status, only MIC volume can be output.
Note:
•WhenOff is selected in MIC function, the MIC gain and
Standby MIC out functions are not available.
•OnlytheStandby mode is set to Network, Standby MIC
out can be selected.
•IftheMICfunctionisturnedonwhenconnectingPCaudio
to the COMPUTER AUDIO IN 2 (MIC IN), loud sound may
be output suddenly depending on the setting value of MIC
gain.
24
AUDIO INPUT SELECTION (see pages 14-16)
AUDIO IN
MIC Setup
RCA L/R terminal
COMPUTER
AUDIO IN 1
MIC Off
Video audio
PC 1 audio
PC 2 audio
MIC On
for Video
Video audio
---
MIC
MIC On
for PC 1
---
PC 1 audio
MIC
MIC On
for PC 2
---
PC 2 audio
MIC
COMPUTER
AUDIO IN 2 ( MIC IN)
Basic Operation
Remote Control Operation
Using the remote control for some frequently used operations is advisable. Just pressing one of the buttons
enables you to make the desired operation quickly without calling up the On-Screen Menu.
COMPUTER 1/2, VIDEO, S-VIDEO and
COMPONENT buttons
Press the COMPUTER 1/2, VIDEO, S-VIDEO and
COMPONENT buttons on the remote control to select the
input source. See pages 27-28, 38-39 for details.
FREEZE button
Press the FREEZE button on the remote control to freeze
the picture on the screen, meanwhile, volume is muted. To
cancel the Freeze function, press the FREEZE button again
or press any other button.
Remote Control
COMPUTER 1/2
buttons
S-video
button
VIDEO
button
Fig.1 will appear on the Screen menu while the Freeze
function is working.
FREEZE
button
Fig.1
D.ZOOM
buttons
COMPONENT
button
INFO.
button
LAMP
button
INFO. button
Display the input source information: Input, H-sync freq.,
V-sync freq., Screen, Language, Lamp status, Lamp
counter, Power management, Keylock, PIN code lock
Remote control, SERIAL NO. and Total power savings
(p.59).
D.ZOOM buttons
Note:
See the next page for the description of other
buttons.
Press the D.ZOOM buttons on the remote control to enter to
the Digital zoom +/– mode. See page 36 for details.
LAMP button
Press the LAMP button on the remote control to select the
lamp mode for changing the brightness on the screen.
Auto ..........
Normal ......
Eco 1 .........
Eco 2 .........
Brightness according to the input signal.
Normal brightness
70%-80% of the normal brightness.
50% of the normal brightness.
25
Basic Operation
NO SHOW button
Press the NO SHOW button on the remote control to black
out the image. To restore to normal, press the NO SHOW
button again or press any other button. When the projected
image is captured and is set as User in the Logo selection
(p. 48), the screen changes each time you press the NO
SHOW button as follows.
No show disappears after 4 seconds.
black out → the captured image →normal →
•••••
P-TIMER button
Press the P-TIMER button on the remote control to operate
the Count up/Count down function. See page 52 for details
of Setting for the P-timer function.
To stop the countdown, press the P-TIMER button. To cancel
the P-Timer function, press and hold the P-TIMER button for
a few seconds.
P-timer
002:02
P-Timer display
IMAGE button
SCREEN button
Press the IMAGE button on the remote control to select a
desired image mode of the screen. See pages 33, 41 for
details.
P-TIMER button
NO SHOW button
IMAGE button
SCREEN button
Select the screen size (See pages 35-37, 44-45 for details).
Note:
See the previous page for the description of
other buttons.
26
Computer Input
Input Source Selection (Computer 1: RGB )
Direct Operation
Choose Computer 1(RGB) or Computer 1(Scart) by pressing the INPUT button on the top control or press the
COMPUTER 1 button on the remote control.
Before using INPUT button, correct input source should be selected through Menu operation as described
below.
Top Control
Remote Control
COMPUTER 1 button
Computer 1(RGB)
Computer 1(RGB) /
(Component) / (Scart)
Computer 1(Scart)
Computer 2(RGB)
INPUT button
Video
S-video
Menu Operation
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
then press the Point ► or the SELECT button.
2
Use the Point ▲▼ buttons to select Computer 1 and
then press the Point ► button.
3
Use the Point ▲▼ buttons to select RGB and then
press the SELECT button.
Input Menu
Computer
1
Note:
When the Input Search function is set to On1 or On2 in
the Auto setup function, the input signal will be searched
automatically (p.47).
27
Computer Input
Input Source Selection (Computer 2: RGB)
Direct Operation
Choose Computer 2(RGB) by pressing the INPUT button on the top control or press the COMPUTER 2 button
on the remote control.
Remote Control
Top Control
INPUT button
COMPUTER 2 button
Computer 1(RGB) /
(Component) / (Scart)
Computer 2(RGB)
Computer 2(RGB)
Video
S-video
Menu Operation
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼buttons to select Input and
then press the Point ► or the SELECT button.
2
Use the Point ▲▼ buttons to select Computer 2 and
then press the SELECT button.
3
When Computer 2 is selected, analog RGB input
source will be selected directly.
Note:
•When the Input Search function is set to On1 or On2,
the input signal will be searched automatically (p.47).
•COMPUTER 2 can not be selected when using
the COMPUTER IN 2/ MONITOR OUT terminal as
MONITOR OUT output.
28
Input Menu
Computer Input
Computer System Selection
This projector automatically tunes to various types of computers with its Multi-scan system and Auto PC
Adjustment. If a computer is selected as a signal source, this projector automatically detects the signal format
and tunes to project a proper image without any additional settings.
(Signal formats provided in this projector are shown on page 71.)
One of the following messages may appear when:
Auto
The projector cannot recognize the connected
signal conforming to the provided PC Systems.
Auto is displayed on the System Menu box
and the Auto PC Adjustment function works
to display proper images. If the image is not
projected properly, a manual adjustment is
required (pp.31-32).
-----
There is no signal input from the computer.
Check the connection between your computer
and the projector. (See “Troubleshooting” on
pages 65-66.)
Mode 1
The preset system is manually adjusted in the
PC Adjust Menu. The adjusted data can be
stored in Mode 1–10 (pp.31-32).
SVGA 1
PC Systems provided in this projector is chosen.
The projector chooses a proper system provided
in the projector and displays it.
PC System Menu
The PC System Menu
Selected system is
displayed.
*Mode 1 and SVGA 1 are examples.
Selecting Computer System Manually
Selecting Computer System Manually
PC system can also be selected manually.
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
then press the Point ► or the SELECT button.
2
Use the Point ▲▼ buttons to select System and then
press the Point ► or the SELECT button.
3
Use the Point ▲▼ buttons to select the desired system
and then press the SELECT button.
PC System Menu
Customized Mode
(1–10) set in the
PC Adjust Menu
(pp.31-32).
Systems in this
dialog box
can be selected.
29
Computer Input
Auto PC Adjustment
Auto PC Adjustment function is provided to automatically adjust Fine sync, Total dots, Horizontal and Vertical
to conform to your computer.
Menu Operation
PC adjust Menu
Auto PC adj.
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select PC adjust
and then press the Point ► button.
2
Use the Point ▲▼ buttons to select Auto PC adj. and
then press the SELECT button.
To store adjustment parameters
The adjusted parameters from the Auto PC Adjustment can
be stored in the projector. Once the parameters are stored,
the setting can be done just by selecting a Mode (1–10) in
the PC System Menu (see page 29). See also “Store” on
page 32.
Note:
•Fine sync, Total dots, Horizontal and Vertical position
of some computers cannot be fully adjusted with
the Auto PC Adjustment function. When the image
is not provided properly with this operation, manual
adjustments are required (pp.31-32).
•TheAutoPCAdjustmentcannotbeoperatedwhen480i,
575i, 480p, 575p, 720p,1035i or 1080i is selected in the
PC System Menu (p.29).
30
Use Point ▲▼ buttons to select Auto PC
adj. and press the SELECT button.
Please wait... appears while the Auto PC
adjustment is in process.
Computer Input
Manual PC Adjustment
Some computers employ special signal formats which may not be tuned by Multi-scan system of this projector.
Manual PC Adjustment enables you to precisely adjust several parameters to match those signal formats. The
projector has 10 independent memory areas to store those parameters manually adjusted. It allows you to recall
the setting for a specific computer.
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select PC adjust
and then press the Point ► or the SELECT button.
2
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button to display the
adjustment dialog box. Use the Point ◄► buttons to
adjust the setting value.
PC adjust Menu
Fine sync
Use the Point ◄► buttons to adjust the value, eliminating a
flicker from the image displayed (from 0 to 31).
Total dots
Use the Point ◄► buttons to adjust the number of total dots
in one horizontal period to match your PC image.
Horizontal
Use the Point ◄► buttons to adjust the horizontal picture
position.
Vertical
Use the Point ◄► buttons to adjust the vertical picture
position.
Current mode
Press the SELECT button to show H-sync freq. and V-sync
freq. of the connected computer.
Clamp
Use the Point ◄► buttons to adjust the clamp level. When
the image has dark bars, try this adjustment.
Display area H
Use the Point ◄► buttons to adjust the horizontal area
displayed by this projector.
Display area V
Use the Point ◄► buttons to adjust the vertical area
displayed by this projector.
31
Computer Input
Reset
Mode free
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
Yes. All adjustments will return to their previous figures.
Mode free
To clear the stored data, select Mode free and then press
the Point ► button or the SELECT button. Move the
highlight to the Mode that you want to clear and then press
the SELECT button.
This Mode has stored
parameters.
Store
To store the adjusted data, select Store and then press the
Point ► button or the SELECT button. Move the highlight
to one of the Modes 1 to 10 in which you want to store, and
then press the SELECT button.
Values of Total dots, Horizontal,
Vertical, Display area H and
Display area V.
Store
Vacant
Press MENU button
to close this dialog
box.
Note:
•Display area (H/V) cannot be selected when 480i, 575i,
480p, 575p, 720p, 1035i or 1080i is selected in the PC
System Menu (p.29).
•Wheninputcomputersignaltotheprojector,PC adjust
will become available.
32
Press SELECT button to
store adjusted data
Computer Input
Image Mode Selection
Direct Operation
Remote Control
Select the desired image mode among Dynamic, Standard,
Real, Cinema, Blackboard(Green), Colorboard, Image 1,
Image 2, Image 3 and Image 4 by pressing the IMAGE
button on the remote control.
IMAGE button
Dynamic
Standard
Real
IMAGE button
Cinema
Blackboard(Green)
Colorboard
1
2
Menu Operation
Image 1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Image
select and then press the Point ► or the SELECT
button.
Image 2
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button.
Image 4
Dynamic
For viewing pictures in a bright room.
Image 3
Image select Menu
Standard
Normal picture mode preset on the projector.
Real
Picture mode with improved halftone for graphics.
Cinema
Picture mode adjusted with fine tone.
Blackboard (Green)
For the image projected on a blackboard.
This mode helps enhance the image projected on a
blackboard. This is mainly effective on a green colored
board, not truly effective on a black colored board.
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
Image 1–4
For viewing with the user preset image mode in the Image
Adjust Menu (see pages 34-35). This Image memory is
provided in each computer, component, S-video and video
input source.
33
Computer Input
Image Adjustment
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Image
adjust and then press the Point ► or the SELECT
button.
2
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button to display the
adjustment dialog box. Use the Point◄► buttons to
adjust the setting value.
Contrast
Press the Point ◄ button to decrease the contrast; press the
Point ► button to increase the contrast (from 0 to 63).
Image adjust Menu
Selected Image mode
Brightness
Press the Point ◄ button to decrease the brightness; press
the Point ► button to increase the brightness (from 0 to 63).
Color temp.
Use the Point ◄► buttons to select the desired Color temp.
level (XLow, Low, Mid or High).
White balance (Red/Green/Blue)
Press the Point ◄ button to lighten R/G/B tone; press the
Point ► button to deepen R/G/B tone (from 0 to 63).
Sharpness
Press the Point ◄ button to decrease the sharpness of the
image; press the Point ► button to increase the sharpness
of the image (from 0 to 15).
Gamma
Use the Point ◄► buttons to adjust the gamma value to
obtain a better balance of contrast (from 0 to 15).
Reset
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
Yes. All adjustments will return to their previous figures.
34
Use the Point ◄►
buttons to adjust the
setting value.
Note:
•WhenWhitebalance Red, Green or Blue is
adjusted, Color temp. will change to User.
•WhenBlackboard(Green) or Colorboard
is selected in Image select, Color temp. will
change to Blackboard or Colorboard.
Computer Input
Store
To store the adjusted data, select Store and press the Point
► button or the SELECT button. Use the Point ▲▼ buttons
to select one from Image 1 to 4 and press the SELECT
button.
A confirmation box appears and then select Yes. Stored
data can be called up by selecting an Image (1–4) in the
Image Mode Selection on page 33.
A confirmation box
appears and then
select Yes.
Screen Size Adjustment
This projector has the picture screen resize function, which
enables you to customize the image size.
1
2
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Screen and
then press the Point ►or the SELECT button.
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button .
Screen Menu
Normal
Provide the image to fit the screen size.
Full
Provide the full screen image.
Wide (16:9)
Provide the image at the 16:9 wide screen ratio.
Zoom
Scale the image proportionally to fit the entire screen. Either
side of image may go over the screen.
True
Provide the image in its original size. When the original
image size is larger than the screen size (1024 x 768), the
projector enters to the panning mode automatically. Use the
Point▲▼◄►buttonstopantheimage.Whenadjusted,
the arrows will turn red. When reached to the correction
limits, the arrows will disappear.
Custom
Provide the last stored aspect screen image.
Note:
•Thisprojectorcannotdisplayanyresolutionhigherthan1920x1200.Ifyourcomputer’sscreenresolutionis
higher than it, reset the resolution lower before connecting to the projector.
•Theimagedatainotherthan1024x768ismodifiedtofitthescreensizeininitialmode.
•True and Digital zoom +/– cannot be selected when 480i, 575i, 480p, 575p, 720p, 1035i or 1080i is
selected in the PC System Menu (p.29).
35
Computer Input
Custom adj.
Adjust the screen scale and position manually with this
function.
Press the Point ► button at Custom and the Custom is
displayedonthescreen,youcanusethePoint▲▼ buttons
to choose the item you want to adjust.
Scale H/V .......... Adjust the Horizontal/Vertical screen
scale.
H&V ................... When set to On, the aspect ratio is
fixed. The Scale V appears dimmed and
becomes unavailable. Adjust Scale H,
then the screen scale is automatically
modified based on the aspect ratio.
Position H/V ..... Adjust the Horizontal/Vertical screen
position.
Common ........... Save the adjusted scale or position to all
the inputs. Press the SELECT button at
Common to display a confirmation box.
To save the scale or position, press the
SELECT button at Yes. When Custom
is selected, the saved scale or position is
used.
Reset ................. Reset all the adjusted values. Press
the SELECT button at Reset to display
a confirmation box. To reset, press the
SELECT button at Yes.
Digital zoom +
Select Digital zoom +. The On-Screen Menu disappears and
D. zoom + appears. Press the SELECT button to expand the
image size. Use the Point ▲▼◄► buttons to pan the image.
The Panning function can work only when the image is larger
than the screen size.
A projected image can be also expanded by pressing the
D.ZOOM ▲ or the SELECT button on the remote control.
Digital zoom –
Select Digital zoom –. The On-Screen Menu disappears
and D. zoom – appears. Press the SELECT button to
compress image size.
The projected image can be also compressed by pressing
the D.ZOOM ▼ or the SELECT button on the remote control.
To exit the Digital zoom +/– mode, press any button except
the D.ZOOM ▲▼ buttons and the SELECT button.
To return to the previous screen size, select a screen size
from the Screen Size Adjustment Menu or select an input
source from the Input Source Selection Menu (see pages
27-28) again, or adjust the screen size with the D.ZOOM
▲▼ buttons.
36
Note:
•When no signal is detected, Normal is
set automatically and the Aspect dialog
box disappears.
•TheadjustablerangeforScale H/V and
Position H/V is limited depending on the
input signal.
Remote Control
POINT ▲▼◄►
buttons
SELECT button
D.ZOOM + button
D.ZOOM - button
Note:
•The minimum compression ratio is
limited depending on the input signal,
when the Keystone function is working
or when the custom is selected for the
screen size.
•True and Digital zoom +/– are disabled
and cannot be displayed when 480i,
575i, 480p 575p, 720p,1035i or 1080i is
selected in the PC System Menu (p.29).
•Digital zoom +/- cannot be selected
when True is selected.
•The minimum compression ratio is
limited at Normal screen size.
Computer Input
Keystone
This function is used to adjust keystone distortion of the
projected image. Use the Point ▲▼ buttons to choose the
item you want to adjust.
Keystone
To correct keystone distortion, press the SELECT button.
Keystone appears on the screen. Use the Point ▲▼
buttons to correct keystone distortion (p.23).
Store
To store or reset the keystone correction, press the
SELECT button.
Store.............Keep the keystone correction even when
the AC power cord is unplugged.
Reset............Release the keystone correction when the
AC power cord is unplugged.
Ceiling
When this function is set to On, the picture will be top/
bottom and left/right reversed. This function is used to
project the image from a ceiling-mounted projector.
Keystone
Ceiling
Rear
Rear
When this function is set to On, the picture will be left/right
reversed. This function is used to project the image from
rear of the screen.
Reset
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
Yes. All adjustments will return to their previous figures.
37
Video Input
Input Source Selection (Video, S-video)
Direct Operation
Top Control
Choose Video or S-video by pressing the INPUT button on
the top control, or the VIDEO button or the S-VIDEO button
on the remote control.
Before using INPUT button, correct input source should be
selected through menu operation as described below.
INPUT button
Computer 1(RGB) /
(Component) / (RGB(Scart))
Computer 2(RGB)
Video
S-video
Remote Control
VIDEO button
Video
S-VIDEO button
S-video
Menu Operation
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
then press the Point ►or the SELECT button.
2
Use the Point ▲▼ buttons to select either Video or
S-video and then press the SELECT button.
Video
When video input signal is connected to the
VIDEO jack, select Video.
S-video
When video input signal is connected to the
S-VIDEO jack, select S-video.
Note:
When the Input Search function is set to On1 or On2 in
the Auto setup function, the input signal will be searched
automatically (p.47).
38
Input Menu
Video Input
Input Source Selection (Component, RGB Scart)
Direct Operation
Choose Computer 1(Component) or Computer 1(Scart) by pressing the INPUT button on the top control or
press the COMPUTER 1 or the COMPONENT button on the remote control.
Before using INPUT button, correct input source should be selected through Menu operation as described
below.
Remote Control
Top Control
INPUT button
COMPUTER 1 button
Computer 1(RGB) /
(Component) / (RGB(Scart))
Computer 1(RGB)
Computer 1(Scart)
Computer 2(RGB)
COMPONENT button
Video
Computer 1
(Component)
Menu Operation
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
then press the Point ► or the SELECT button.
2
Use the Point ▲▼ buttons to select Computer 1 and
then press the Point ► button.
3
Use the Point▲▼ buttons to select Component or
RGB(Scart) and then press the SELECT button.
Component
When the input source is coming from video
equipment connected to the COMPUTER
IN 1/COMPONENT IN terminal with a
Component-VGA Cable, select Component.
RGB (Scart)
When the input source is coming from video
equipment connected to the COMPUTER
IN 1/COMPONENT IN terminal with a ScartVGA Cable, select RGB (Scart).
S-video
Input Menu
Note:
When the Input Search function is set to On1 or On2,
the input signal will be searched automatically (p.47).
39
Video Input
Video System Selection
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Input and
then press the Point ► or the SELECT button.
2
Use the Point ▲▼ buttons to select Video, S-video
or Computer 1(Component) and then press the
SELECT button.
3
Use the Point ▲▼ buttons to select System and then
press the Point ► or SELECT button. Use the Point
▲▼ buttons to select the desired system and then
press the SELECT button.
AV System Menu (Video or S-video)
Video or S-video
Auto
The projector automatically detects an incoming video
system, and adjusts itself to optimize its performance.
When Video System is PAL-M or PAL-N, select the system
manually.
PAL/SECAM/NTSC/NTSC4.43/PAL-M/PAL-N
If the projector cannot reproduce proper video image,
select a specific broadcast signal format from among PAL,
SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N.
Component
Auto
The projector automatically detects an incoming video
signal, and adjusts itself to optimize its performance.
COMPONENT VIDEO SIGNAL FORMAT
If the projector cannot reproduce proper video image, select
a specific component video signal format from among 480i,
575i, 480p, 575p, 720p, 1035i and 1080i.
Note:
The AV System Menu cannot be selected when selecting
RGB (Scart).
40
AV System Menu (Component)
Video Input
Image Mode Selection
Direct Operation
Remote Control
IMAGE button
Dynamic
Select the desired image mode among Dynamic, Standard,
Real, Cinema, Blackboard (Green), Colorboard, Image
1, Image 2, Image 3 and Image 4 by pressing the IMAGE
button on the remote control.
Standard
Real
Menu Operation
Cinema
1
2
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select
Image select and then press the Point ► or the
SELECTbutton.
IMAGE button
Blackboard(Green)
Colorboard
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button .
Image 1
Image 2
Image 3
Image 4
Dynamic
For viewing pictures in a bright room.
Image select Menu
Standard
Normal picture mode preset on the projector.
Real
Picture mode with improved halftone for graphics.
Cinema
Picture mode adjusted with fine tone.
Blackboard (Green)
For the image projected on a blackboard.
This mode helps enhance the image projected on a
blackboard. This is mainly effective on a green colored
board, not truly effective on a black colored board.
Colorboard
At the time of simple projection on the colored wall, you
can get the close color image to the color image projected
on a white screen by selecting the similar color to the wall
color from the preset four colors.
Image 1–4
For viewing with the user preset image mode in the Image
Adjust Menu (see pages 42–43). This Image memory is
provided in each computer, component, S-video and video
input source.
41
Video Input
Image Adjustment
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select the Image
adjust and then press the Point ► or the SELECT
button.
2
Use the Point ▲▼ buttons to select the desired item
and then press the SELECT button to display the
adjustment dialog box. Use the Point ◄► buttons to
adjust the setting value.
Image adjust Menu
Contrast
Press the Point ◄ button to decrease the contrast; press the
Point ► button to increase the contrast (from 0 to 63).
Selected Image mode
Brightness
Press the Point ◄ button to decrease the brightness; press
the Point ► button to increase the brightness (from 0 to 63).
Color
Press the Point ◄ button decrease the intensity of the color;
press the Point ► button increase the intensity of the color
(from 0 to 63).
Tint
Press the Point ◄► buttons to adjust the tint value to get a
proper color balance (from 0 to 63).
Use the Point◄►buttons
to adjust the setting value.
Color temp.
Use the Point ◄► buttons to select the desired Color temp.
level (XLow, Low, Mid or High).
White balance (Red/Green/Blue)
Press the Point ◄ button to lighten R/G/B tone; press the
Point ► button to deepen R/G/B tone (from 0 to 63).
Note:
•WhentheWhite balance Red, Green or Blue is adjusted, the Color temp. level will change to User.
•Tint cannot be selected when the video system is PAL, SECAM, PAL-M or PAL-N (p.40).
•WhenBlackboard(Green)orColorboardisselectedinImageselect,Color temp. will change to Blackboard
or Colorboard.
42
Video Input
Sharpness
Press the Point ◄ button to decrease the sharpness of the
image; press the Point ► button to increase the sharpness
of the image (from 0 to 15).
Gamma
Use the Point ◄► buttons to adjust the gamma value to
obtain a better balance of contrast (from 0 to 15).
Noise reduction
Noise interference on the screen can be reduced. Select
one of the following options to get smoother images.
Off ......... Disabled.
L1 .......... Lower reduction
L2 .......... Higher reduction
Progressive
An interlaced video signal can be displayed in progressive
mode. Select one of the following options.
Off ......... Disabled.
L1 .......... For an active picture.
L2 .......... For a still picture.
Film ....... For watching a film. With this function, the
projector reproduces pictures faithful to the
original film quality.
Reset
Store Menu
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
Yes. All adjustments will return to their previous figures.
Store
To store the adjusted data, select Store and press the Point
► button or the SELECT button. Use the Point ▲▼ buttons
to select one from Image 1 to 4 and press the SELECT
button.
A confirmation box appears and then select Yes. Stored
data can be called up by selecting an Image (1–4) in the
Image Mode Selection on page 41.
Note:
Noise reduction and Progressive cannot be selected
when 480p, 575p, 720p, 1035i or 1080i is selected
(p.40).
A confirmation box
appears and then
select Yes.
43
Video Input
Screen Size Adjustment
This projector has the picture screen resize function, which enables you to customize the image size.
1
Press the MENU button to display the On-Screen
Menu. Use the Point ▲▼ buttons to select Screen and
then press the Point ► or the SELECT button.
2
Use the Point ▲▼ buttons select the desired item and
then press the SELECT button.
Screen Menu
Normal
Provide the image to fit the screen size.
Full
Provide the full screen image.
Wide (16:9)
Provide the image at the 16:9 wide screen ratio.
Zoom
Scale the image proportionally to fit the entire screen. Either
side of image may go over the screen.
Custom
Provide the last stored aspect screen image.
Custom adj.
Adjust the screen scale and position manually with this
function.
Press the Point ► button at Custom and the Custom is
displayedonthescreen,youcanusethePoint▲▼ buttons
to choose the item you want to adjust.
Scale H/V .......... Adjust the Horizontal/Vertical screen
scale.
H&V ................... When set to On, the aspect ratio is
fixed. The Scale V appears dimmed and
becomes unavailable. Adjust Scale H,
then the screen scale is automatically
modified based on the aspect ratio.
Position H/V ..... Adjust the Horizontal/Vertical screen
position.
Common ........... Save the adjusted scale or position to all
the inputs. Press the SELECT button at
Common to display a confirmation box.
To save the scale or position, press the
SELECT button at Yes. When Custom
is selected, the saved scale or position is
used.
Reset ................. Reset the all adjusted values. Press
the SELECT button at Reset to display
a confirmation box. To reset, press the
SELECT button at Yes.
44
Note:
•When no signal is detected, Normal is set
automatically and the Aspect dialog box
disappears.
•The adjustable range for Scale H/V and
Position H/V is limited depending on the
input signal.
Video Input
Keystone
This function is used to adjust keystone distortion of the
projected image. Use the Point ▲▼ buttons to choose the
item you want to adjust.
Keystone
To correct keystone distortion, press the SELECT button.
Keystone appears on the screen. Use the Point ▲▼
buttons to correct keystone distortion (p.23).
Store
To store or reset the keystone correction, press the
SELECT button.
Store............Keep the keystone correction even when
the AC power cord is unplugged.
Reset............Release the keystone correction when the
AC power cord is unplugged.
Ceiling
When this function is set to On, the picture will be top/bottom
and left/right reversed. This function is used to project the
image from a ceiling-mounted projector.
Keystone
Ceiling
Rear
Rear
When this function is set to On, the picture will be left/right
reversed. This function is used to project the image from
rear of the screen.
Reset
To reset the adjusted data, select Reset and press the
SELECT button. A confirmation box appears and then select
Yes. All adjustments will return to their previous figures.
45
Setting
Setting
This projector has a Setting menu that allows you to set up
the other various functions described below.
1
2
3
Press the MENU button to display the On-Screen
Menu. Press the Point ▲▼ buttons to select the
Setting and press the Point ► or the SELECT button
to access the submenu items.
Use the Point ▲▼ buttons to select the desired item
and then press the Point ► or the SELECT buttons to
access the selected item.
Use the Point ▲▼ buttons select the desired item and
then press the SELECT button.
Language
The language used in the On-Screen Menu is available in
English, German, French, Italian, Spanish, Portuguese,
Dutch, Swedish, Finnish, Polish, Hungarian, Romanian,
Czech, Russian, Turkish, Kazakh, Vietnamese, Chinese,
Korean, Japanese and Thai.
Menu position
This function is used to change the position of the
On-Screen Menu. Select Menu position and press the
SELECT button.
The Menu position changes each time you press the
SELECT button as follows.
the center
the bottom left
the bottom right
the top
left
the top right
the center .....
46
Setting Menu
Language
Setting
Auto setup
Auto setup
This function enables Input search, Auto Keystone correction
and Auto PC adjustment by pressing the AUTO SETUP button
on the top control or the AUTO SET button on the remote
control. Settings for those functions can be altered as follows:
Input search
This function detects the input signal automatically. When
a signal is found, the search will stop. Use the Point ▲▼
buttons to select one of the following options.
Off ........... Input search will not work.
On1.......... Input search works when.
– Pressing the AUTO SETUP button on the top
control or the AUTO SET button on the remote
control.
On2.......... Input search works under the following situation.
– When turning on the projector by pressing the
ON/STAND-BY button on the top control or the
remote control.
– When pressing the AUTO SETUP button on
the top control or the AUTO SET button on the
remote control.
– When the current input signal is cut off.*
* If the No show or Freeze function is active, cancel it to
activate the Input search. It is also unavailable when
On-Screen menu is displayed.
Auto PC adj.
On. . . . . . . . Enables Auto PC Adjustment when pressing
the AUTO SET button on the remote control or
the AUTO SETUP button on the top control.
Off . . . . . . . Disables Auto PC Adjustment.
Auto Keystone
Auto . . . . . Always works and corrects keystone distortion
according to the projector's tilt.
Manual . . . . Works only when pressing the AUTO SETUP
button on the top control or the AUTO SET
button on the remote control.
Off . . . . . . . Disables Auto Keystone.
Note:
•WhileInput search is set to On1 or On2, the status of
Input and Lamp are displayed every time the signal is
switched.
•Onlythelastselectedinputsourcecanbedetected.
•IftheINPUTbuttononthetopcontrolorthe
COMPUTER 1/2 buttons, VIDEO or S-VIDEO or
COMPONENT button on the remote control is pressed
during Input search is in progress, Input search will stop
and go back to the previous input signal.
•Input search, Auto PC adj. and Auto Keystone cannot
be set Off at the same time.
Note:
•Auto Keystone corrects vertical distortion only,
not correct horizontal distortion.
•The Auto Keystone function cannot work when
the Ceiling feature is set On in the Setting menu
(pp.37, 45).
•Perfect correction of the image distortion cannot
be ensured with the Auto setup function. If the
distortion is not corrected properly by pressing
the AUTO SETUP or AUTO SET button, adjust
manually by pressing the KEYSTONE button on
the remote control or selecting Keystone in the
Setting menu (pp.23, 37, 45).
•Fine sync, Total dots, Horizontal and Vertical
position of some computers cannot be fully
adjusted with the Auto PC Adjustment function.
When the image is not provided properly with
this operation, manual adjustments are required
(pp.31-32).
47
Setting
Background
Select the background screen when no input signal is
detected. Press the Point ▲▼ buttons to switch between
each option.
Blue . . . Project a blue background
User . . . Project an image captured in the Logo setting.
Black . . Project a black background
Display
This function decides whether to display On-Screen Displays.
On ........................... Show all the On-Screen displays.
Use this function when you want
to project images after the lamp
becomes bright enough. The factory
default setting is in this option.
Countdown Off....... Show the input image instead of
the countdown when turning on the
projector. Use this function when you
want to project the image as early as
possible even when the lamp is not
bright enough.
Off ........................... Hide the On-Screen Displays except;
On-Screen Menu
Power off? (p.20)
No signal for Power management
(p.51)
Please wait ...
Arrows for the True function in the
Screen Menu (p.35)
P-Timer
Logo (Logo and Logo PIN code lock settings)
This function allows you to customize the screen logo with
Logo select, Capture, Logo PIN code lock and Logo PIN
code change functions.
Note:
When On is selected in the Logo PIN code lock function,
Logo select and Capture functions cannot be selected.
Logo select
This function decides on the starting-up display from
among following options.
Off ........... Show the countdown display only.
Default .... Show the factory-set logo.
User ........ Show the image you captured.
48
Logo select
Setting
Capture
This function enables you to capture an image being
projected to use it for a starting-up display or interval of
presentations.
Capture
Select Capture and press the SELECT button.
A confirmation box appears and select Yes to capture the
projected image.
After capturing the projected image, go to the Logo select
function and set it to User. Then the captured image will be
displayed the next time you turn on the projector.
To cancel the capture function, select Yes in the "Quit?"
confirmation box.
Note:
•Before capturing an image, select Standard in the
Image select Menu to capture a proper image (pp.33,
41).
•A signal from a computer can be captured up to XGA
(1024 x 768). A signal from video equipment can be
captured except for 720p, 1035i and 1080i.
•When capturing the image that has been adjusted by
the Keystone function, the adjusted data is automatically
reset and the projector captures an image without
keystone correction.
•WhenLogo PIN code lock is set to On, capture cannot
be selected.
•When starting to capture a new image, the previously
stored image is cleared even if you cancel the capturing.
•When there is no captured image or it is interrupted
while capturing an image, User can not be selected, you
can only switch between Default and Off.
Logo PIN code lock
Logo PIN code lock
This function prevents an unauthorized person from
changing the screen logo.
On ........... The screen logo cannot be changed without a
Logo PIN code.
Off ........... The screen logo can be changed freely from
the Logo Menu (p.48).
If you want to change the Logo PIN code lock setting,
press the SELECT button and the Logo PIN code dialog
box appears. Enter a Logo PIN code by following the steps
below. The initial Logo PIN code is set to “4321” at the
factory.
49
Setting
Enter a Logo PIN code
Use the Point ▲▼ buttons to enter a number. Press the
Point ► button to fix the number and move the red frame
pointer to the next box. The number changes to “ ”. If
you fixed an incorrect number, use the Point ◄ button to
move the pointer to the number you want to correct, and
then enter the correct number.
Enter a Logo PIN code
Logo PIN code
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to
Set. Press the SELECT button so that you can start to
operate the projector.
If you entered an incorrect Logo PIN code, Logo PIN
code and the number (
) will turn red for a
moment. Enter the correct Logo PIN code all over again.
Change the Logo PIN code lock setting
Use the Point ▲▼ buttons to switch On or Off, and then
press the SELECT button to make a choice.
Logo PIN code change
Logo PIN code change
Logo PIN code can be changed to your desired fourdigit number. Press the SELECT button to select Logo
PIN code change. Current logo PIN code dialog box
appears, use the Point ▲▼ buttons to enter the current
code. The New Logo PIN code input dialog box appears.
Set a new Logo PIN code, confirmation box appears,
choose Yes to set the new Logo PIN code.
Be sure to note the new Logo PIN code and keep it on
hand. If you lost the number, you could no longer change
the Logo PIN code setting.
CAUTION:
WHEN YOU HAVE CHANGED THE LOGO PIN CODE,
WRITE DOWN THE NEW PIN CODE IN COLUMN OF
THE LOGO PIN CODE NO. MEMO ON PAGE 76, AND
KEEP IT SECURELY. SHOULD THE LOGO PIN CODE
BE LOST OR FORGOTTEN, THE LOGO PIN CODE
SETTING CAN NO LONGER BE CHANGED.
50
Setting
Terminal
The COMPUTER IN 2/MONITOR OUT terminal on the back
of the projector is switchable for computer input or monitor
output. (See page 9) Select Computer 2 or Monitor Out
with the Point ▲▼buttons.
Computer 2 . . computer input
Monitor Out . . monitor out
Terminal function is not available when Computer 2 is
selected to the input source. Change the input source to the
others (Computer 1, Video or S-video) so that the Terminal
function will be available. (pp.25, 27, 38, 39)
Power management
Power management
For reducing power consumption as well as maintaining
the lamp life, the Power management function turns off the
projection lamp when the projector is not operated for a
certain period.
Time left before Lamp is off.
Select one of the following options:
Ready .................. When the lamp has been fully cooled
down, the POWER indicator changes
to green blinking. In this condition, the
projection lamp will be turned on if the
input signal is reconnected or any button
on the top control or remote control is
pressed.
Shut down .......... When the lamp has been fully cooled
down, the power will be turned off.
Off ....................... Power management function is off.
Timer ................... If the input signal is interrupted and
no button is pressed for more than
30 seconds, the timer display with No
signal appears. It starts the countdown
until the lamp is turned off. Use the Point
▲▼ buttons to set the Timer(1~30min.).
Note:
Factory default is Ready: 5 Min.
Direct on
When this function is set to On, the projector will be
automatically turned on just by connecting the AC power
cord to a wall outlet.
Note:
Be sure to turn off the projector properly (see “Turning
Off the Projector” on page 20). If the projector is turned
off in the incorrect sequence, the Direct on function does
not work properly.
51
Setting
Standby mode
This function is available when operating the projector via
network.
Eco ............ Select Eco when you do not use the projector
via network. The projector’s network function
will stop when turning off the projector.
Network .... Supply the power to the network function even
after turning off the projector. You can turn on/
off the projector via network, modify network
environment, and receive an e-mail about
projector status while the projector is powered
off.
Refer to the owner’s manual of “Network Set-up and
Operation”.
Note:
•FactorydefaultisNetwork.
•When selecting Network, the cooling fans may be running
depending on the temperature inside the projector even if
the projector is turned off.
X: disabled
O: enabled
*1
Serial command
Network
Monitor Out
Audio Out
Direct on
*2
*1 When Eco is selected, it is only possible to
turn on the projector while using the
RS-232C serial port.
*2 When switch the Standby MIC out function
On and in Standby mode status, only MIC
volume can be output.
P-timer
0
P-timer display
P-timer
This function allows you to change the setting of the
P-timer and execute it.
Select one of the following options:
Count up ... The P-timer display 000:00 appears on
the screen and the count starts
(000:00–180:00)
Count down .. The time set in the Timer setting appears
on the screen and the countdown starts.
Timer ......... Use the Point ▲▼ buttons to set the
Timer (1–180 Min). Timer is available in
Count down only. Factory default velue is
10 Min.
Start .......... It executes the count up or count down
function. Press the SELECT button at
Start and the indication changes into
Stop. To stop Count up or Count down,
press the SELECT button at Stop on
the screen menu, then the indication
changes into Restart. Press the SELECT
button at Restart to resume Count up or
Count down.
Reset ......... Reset the P-timer values.
Press the SELECT button at Reset to
return to the following value;
Count up ... "000:00"
Count down ... Timer that you set
Exit ............ To exit the P-timer operation.
52
Stop or Cancel the P-timer via Remote Control
To stop the P-timer function, press the P-TIMER
button.
To cancel the P-timer, press and hold the P-TIMER
button for a few seconds.
Setting
Closed caption
Closed Caption
Closed caption is a function that displays the audio portion
of a TV program as text on the screen. If the input signal
contains closed captions, you can turn on the feature and
switch the channels. Press the Point ▲▼ buttons to select
Off, CC1, CC2, CC3 or CC4.
If the closed caption is not clear, you can change the text
from Color to White.
Note:
The Closed caption is available only under the situation
below.
•WhentheinputsignalisNTSCofcompositeand S-video, and the system is set according to the signal
or set on Auto.
•ThesystemmustbesetonNTSC or Auto in Video
System Selection. (p.40)
•TheiconofClosedcaptionisdisplayedingraywhileit
is not available.
•The Closed caption is unavailable when On-Screen
menu and P-Timer are displayed.
Press the Point ▲▼ buttons to
select Off, CC1, CC2, CC3 or CC4,
and then Press SELECT button.
53
Setting
Lamp life control
Lamp control
Lamp control
This function allows you to change brightness of the screen.
Auto ..........
Normal ......
Eco 1 .........
Eco 2 .........
Brightness according to the input signal.
Normal brightness
70%-80% of the normal brightness.
50% of the normal brightness.
Lamp life control
Select the lamp operation when the total lighting time of a
lamp exceeds the recommended total hours of use.
Mode 1 .............. The lamp can be turned on even after
exceeding the recommended total
hours of use.
Mode 2 .............. The lamp can be turned on even after
exceeding the recommended total
hours of use. But the projector turns off
automatically after 3 minutes.
Note:
•Lamp mode cannot be changed for a while after turning
on the projector. Lamp needs some time to stabilize
after the power is turned on. Stored lamp mode will be
active after the lamp is stabilized.
•IfMode 2 has been selected and the projection lamp
exceeds the recommended total hours of use, the
replacement icon will be displayed at the time of poweron. Then the projector will turn off after 3 minutes.
Lamp replacement icon
•TheLampreplacementiconwillnotappearwhenthe
Display function is set to Off (p.48), during Freeze
(p.25) or No show (p.26).
Remote control
This projector provides two different remote control codes:
the factory-set initial code (Code 1) and the secondary code
(Code 2). This switching function prevents remote control
interference when operating several projectors or video
equipment at the same time.
When operating the projector in "Code 2", both the projector
and the remote control must be switched to "Code 2".
Remote control
To change the code for the projector:
Select either "Code 1" or "Code 2" in this Setting Menu.
To change the code for the remote control:
Press and hold both the MENU and IMAGE buttons
together for 5 seconds or more. After changing the code,
make sure the remote control operates properly.
Note:
•Whendifferentcodesaresetontheprojectorandontheremotecontrol,anyoperationcannotbemade.In
that case, switch the code on the remote control to fit the code on the projector.
•Ifthebatteriesareremovedfromtheremotecontrolforalongperiodoftime,theremotecontrolcodewillbereset.
54
Setting
Security (Key lock and PIN code lock)
Key lock
This function allows you to use the Key lock and PIN code
lock function to set the security for the projector operation.
Key lock
This function locks the top control and remote control
buttons to prevent operation by unauthorized persons.
Select Key lock and then press the SELECT button,
and select the desired item by pressing the Point
▲▼buttons.
..... Unlocked.
..... Lock the operation of the top control. To
unlock, use the remote control.
..... Lock the operation of the remote control.
To unlock, use the top control.
If the top control accidentally becomes locked and you do
not have the remote control nearby or there is something
wrong with your remote control, contact the dealer where
you purchased the projector or the service center.
PIN code lock
This function prevents the projector from being operated
by unauthorized persons and provides the following
setting options for security.
Off ........... Unlocked.
On1 ......... Enter the PIN code every time turning on
the projector.
On2 ......... Enter the PIN code to operate the projector
once the power cord is disconnected; as
long as the AC power cord is connected,
the projector can be operated without a
PIN code.
Whenever you change the PIN code lock setting or the
PIN code (the four-digit number), you are required to
enter the PIN code. The “1234” is set as the initial PIN
code at the factory.
PIN code lock
If you want to change the PIN code lock setting, Press
the SELECT button and the PIN code dialog box
appears.
When the projector is locked with the PIN code, the
Security icon appears on the guide.
55
Setting
Enter a PIN code
Use the Point ▲▼ buttons to enter a number. Press the
Point ► button to fix the number and move the red frame
pointer to the next box. The number changes to “ ”. If
you fixed an incorrect number, use the Point ◄ button to
move the pointer to the number you want to correct, and
then enter the correct number.
Enter a PIN code
Repeat this step to complete entering a four-digit number.
After entering the four-digit number, move the pointer to
“Set.” Press the SELECT button so that you can change
the following PIN code lock setting.
If you entered an incorrect PIN code, PIN code and the
number (
) will turn red for a moment. Enter the
correct PIN code all over again.
Change the PIN code lock setting
Use the Point ▲▼ buttons to select Off, On1, or On2,
and then press the SELECT button to make a choice.
PIN code change
The PIN code can be changed to your desired fourdigit number. Press the SELECT button to select PIN
code change. The Current PIN code input dialog box
appears, use the Point ▲▼ buttons to enter the current
code. The New PIN code input dialog box appears. Set
a new PIN code.
CAUTION:
WHEN YOU HAVE CHANGED THE PIN CODE, WRITE
DOWN THE NEW PIN CODE IN COLUMN OF THE
PIN CODE NO. MEMO ON PAGE 76, AND KEEP IT
SECURELY. IF YOU FORGET YOUR PIN CODE, THE
PROJECTOR CAN NO LONGER BE STARTED.
Fan
This function provides the following options in the cooling
fans’ operation when the projector is turned off (p.20).
L1 ...... Normal operation
L2 ...... Slower and lower-sound than the normal
operation (L1), but it takes more time to cool the
projector down.
56
Change the PIN code
Setting
Fan control
Choose the running speed of cooling fans from the following
options according to the ground elevation under which you
use the projector.
Off................ Normal speed. Set this function to Off when
using the projector in non-high altitude
environment.
On 1............. Faster than Off mode. Select this mode
when using the projector in high altitudes
(about 1,200 meters or more above the sea
level) where the fans have less cooling effect.
On 2............. Faster than On 1 mode. Select this mode
when using the projector in higher altitudes
than above where the fans have lesser cooling
effect.
Note:
• The fan noise becomes louder in On 1 and On2.
• Failure to set the running speed of cooling fans properly
may affect the projector life.
Video delay control
When you want to make a digital processing of a projected
image faster, set this function.
UsethePoint▲▼buttons,selectanitemofOfforOn.
Note:
Noise reduction and Progressive can not be selected
when Video delay control function is set to On.
Filter counter
This function is used to set a frequency for the filter
replacement.
UsethePoint▲▼buttonstoselectFiltercounterandthen
pressthePoint►ortheSELECTbuttontoaccessthe
submenu items.
Filter counter...........Show the total accumulated time
of the filter use timer setting.
Timer........................To set a timer, when the projector
reaches the time, the Filter warning
icon (Fig.1) appears on the screen
and the total accumulated time
turns red, indicating that the filter
replacement is necessary.
Filter counter reset... After replacing the filters, be sure
to reset the timer. The Filter warning
icon will not turn off until the filter
counter is reset. For details about
resetting the timer, refer to
“Resetting the Filter Counter” on
page 61.
Fig.1 Filter warning icon
Filter counter
Press the SELECT button to select Timer,
and then use the Point ▲▼buttons to set
the timer. Select from (Off/1000H/ 2000H/
3000H/4000H/5000H/6000H) depending on
the use environment.
Filter warning icon appears on the screen at a set time.
(Off/1000H/2000H/3000H/4000H/5000H/6000H).
Note:
•This icon also appears at turning on.
• The Filter warning icon (Fig.1) will not appear when the Display function is set to Off (p.48), during
Freeze(p.25), or No show (p.26).
57
Setting
Total power savings
This function displays the saved amount of power and the
exhausted CO2 of the projector.
Total power savings
UsethePoint▲▼buttonstoselectTotalpowersavings
and then pressthePoint►ortheSELECTbuttontoaccess
the submenu items.
Total power savings......Show the total accumulated
power savnings of the projector
and display the total amount of
CO2 exhausted from the
projector.
Reset...............................Reset the figures of the total
power savnings and the
exhausted CO2.
Warning log
This function records anomalous operations while the
projector is in operation and use it when diagnosing faults.
Up to 10 warning logs are displayed with the latest warning
message at the top of the list, followed by previous warning
messages in chronological order.
Note:
When the Factory default function is executed, all the
warning log records will be deleted.
Factory default
This function returns all setting values except for the PIN
code lock, Logo PIN code lock, User logo, Filter counter
and Total power savings to the factory default settings.
58
Factory default
Information
Input Source Information Display
The Information Menu is used for checking the status of the image signal being projected and the operation of the projector.
Direct Operation
Press the INFO. button on the remote control to display the
Information Menu.
Remote Control
Menu Operation
Press the Point ▲▼ buttons to select the Information. The
Information Menu is displayed.
INFO. button
See below for displayed information.
Input
The selected input source is displayed.
Information Menu
H-sync freq.
The horizontal frequency of the input signal is displayed in
KHz, or - - - - KHz when no signal.
V-sync freq.
The vertical frequency of the input signal is displayed in Hz,
or - - - - Hz when no signal. Numbers of Hz doubles when
during Interlace.
Screen
The selected screen size is displayed.
Language
The selected language is displayed.
Lamp status
The selected lamp mode is displayed.
Lamp counter
The cumulative lamp operating time is displayed.
Power management
Off, Ready, Shut down or Timer is displayed.
Key lock
The selected Key lock icon is displayed.
PIN code lock
Off or On 1 or On 2 is displayed.
Remote control
The selected remote code is displayed.
SERIAL NO.
The serial number of the projector is displayed. The serial
number is used to service the projector.
Total power savings
The saved amount of power and the exhausted CO2 are
displayed.
59
Maintenance and Cleaning
WARNING indicator
The WARNING indicator shows the state of the function which protects the projector. Check the state of the
WARNING indicator and the POWER indicator to take proper maintenance.
The projector is shut down and the WARNING
indicator is blinking red.
Top Control
When the temperature inside the projector reaches a
certain level, the projector will be automatically shut down to
protect the inside of the projector. The POWER indicator is
blinking while the projector is being cooled down. When the
projector has cooled down enough (to its normal operating
temperature), it can be turned on again by pressing the ON/
STAND-BY button.
WARNING blinking
red
Note:
The WARNING indicator continues to blink even after
the temperature inside the projector returns to normal.
When the projector is turned on again, the WARNING
indicator stops blinking.
Then check the matters below:
– Did you provide appropriate space for the projector to be
ventilated? Check the installing condition to see if the air
vents of the projector are not blocked.
– Has the projector been installed near an Air-Conditioning/
Heating Duct or Vent? Move the installation of the
projector away from the duct or vent.
– Is the filter clean? Replace the filters with new ones.
The projector is shut down and the WARNING
indicator lights red.
When the projector detects an abnormal condition, it is
automatically shut down to protect the inside of the projector
and the WARNING indicator lights red. In this case, unplug
the AC power cord and reconnect it, and then turn the
projector on once again to verify operation. If the projector
cannot be turned on and the WARNING indicator still lights
red, unplug the AC power cord and contact the service
center.
CAUTION
DO NOT LEAVE THE PROJECTOR WITH THE
AC POWER CORD CONNECTED UNDER AN
ABNORMAL CONDITION. IT MAY RESULT IN
FIRE OR ELECTRIC SHOCK.
60
Top Control
WARNING emit a
red light
Maintenance and Cleaning
Replacing the Filters
Filter prevents dust from accumulating on the optical elements inside the projector. Should the filter become
clogged with dust particles, it will reduce cooling fans’ effectiveness and may result in internal heat buildup
and adversely affect the life of the projector. If a “Filter warning” icon appears on the screen, replace the filters
immediately. Replace the filters by following the steps below.
1
Turn off the projector and unplug the AC power cord
from the AC outlet.
2
Turn over the projector and pull out the filter cover
(bottom); pull up the handle and take out the whole
filter (bottom.)
Press up the latches and pull out the filter cover (side);
pull out the handle and take out the side filter.
3
Put new filters back into the position. Make sure that
the filters are fully inserted to the projector.
4
Connect the AC power cord to the projector and turn
on the projector.
CAUTION
–Do not operate the projector with the filters
removed. Dust may accumulate on the optical
elements degrading picture quality.
–Do not put anything into the air vents. Doing so
may result in malfunction of the projector.
–Do not wash the filters with water or any other
liquid matter. Otherwise the filters may be
damaged.
Filter cover (bottom)
Handle (pull up)
Filter cover (side)
Latches (press up)
Handle (pull out)
Filter counter
RECOMMENDATION
We recommend avoiding dusty/smoky environments
when you operate the projector. Usage in these
environments may cause poor image quality.
When using the projector under dusty or smoky conditions,
dust may accumulate on a lens, LCD panels, or optical
elements inside the projector degrading the quality of a
projected image. When the symptoms above are noticed,
contact your authorized dealer or service center for proper
cleaning.
Resetting the Filter Counter
Be sure to reset the Filter counter after replacing the filters.
1
Press the MENU button to display the On-Screen Menu.
Use the Point▲▼ buttons to select the Setting Menu
and then press the Point ► or the SELECT button.
2
Use the Point ▲▼buttons select Filter counter and
then press the Point ►or the SELECT button. Use the
Point ▲▼ buttons to select Filter counter reset and
then press the SELECT button. The Filter counter
Reset? appears. Select Yes to continue.
3
Another confirmation dialog box appears, select Yes to
reset the Filter counter.
The Filter counter
Reset? appears.
Select Yes, then
another confirmation
box appears.
Select Yes again
to reset the Filter
counter.
61
Maintenance and Cleaning
Attaching the Lens Cap
When moving this projector or while not using it over an
extended period of time, replace the lens cap.
Attach the lens cap according to the following procedures.
1
Thread the string through the hole on the lens cap and
then tie a knot in the string to secure it in place.
2
To pass the other end of the string into the hole on the
top of the projector and pull at it.
Cleaning the Projection Lens
Unplug the AC power cord before cleaning.
Gently wipe the projection lens with a cleaning cloth that
contains a small amount of non-abrasive camera lens
cleaner, or use a lens cleaning paper or commercially
available air blower to clean the lens.
Avoid using an excessive amount of cleaner. Abrasive
cleaners, solvents, or other harsh chemicals might scratch
the surface of the lens.
Cleaning the Projector Cabinet
Unplug the AC power cord before cleaning.
Gently wipe the projector body with a soft dry cleaning cloth.
When the cabinet is heavily soiled, use a small amount of
mild detergent and finish with a soft dry cleaning cloth. Avoid
using an excessive amount of cleaner. Abrasive cleaners,
solvents, or other harsh chemicals might scratch the surface
of the cabinet.
When the projector is not in use, put the projector in
an appropriate carrying case to protect it from dust and
scratches.
CAUTION
Do not use any flammable solvents or air sprays on the
projector and in its vicinity. The explosion or fire hazard may
occur even after the AC power cord is unplugged because
the temperature inside the projector is extremely high due to
the lamps. In addition, there is a risk that the internal parts
may be damaged not only by the flammable air spray but
also by the cold air.
62