W52P User Guide
Packaging Contents
The following components are included in your W52P/W52H IP DECT phone
packages
W52P Package
!
!
!
!
!
!
!
!
!
1 Base Station
1 Handset
1 Charge Cradle
2 Power Adapters (one for the
base station is optional)
2 Rechargeable Batteries
1 Ethernet Cable
1 Belt Clip
1 Quick Start Guide
W52P Base Station
W52H Package
!
!
!
!
!
1
1
1
2
1
Handset
Charge Cradle
Power Adapter
Rechargeable Batteries
Belt Clip
!
W52P/W52H Handset
!
Charger Cradle
!
Power Adapter
!
Two Rechargeable Batteries
!
Ethernet Cable
!
Belt Clip
Connect the supplied Ethernet cable between the Internet port on the base station and
the Internet port in your network or the switch/hub device port.
To insert batteries into the handset:
•
Open the battery cover.
•
Insert the batteries in the correct polarity.
•
Close the battery cover.
We Strongly Recommend You Use These
Rechargeable Batteries Only
Setting up the Charger Cradle
1. Connect the DC plug on the power adapter to the DC5V port on the charger
cradle.
2. Connect the other end of the power adapter into an electrical power outlet.
Charging the Handset
To charge the handset:
1. After setting up the handset and charger cradle, place the handset in the charger
cradle.
The original handset included in the W52P package is pre-registered to
the base station. After charging, the handset is ready for use.
Battery Charging Status
The handset batteries take 6 hours to fully charge. Charging status of batteries
is displayed on the top right-hand corner of the LCD screen:
Icon
Charging Status
Fully Charged
75% Charged
50% Charged
Base Station Description
After the base station starts up successfully and the handset is registered to the
base station, all LEDs on the base station illuminate green in sequence.
Hardware component instructions of the W52P base station are:
Item
Paging Key
Registration LED
Network
LED
Power
LED
Description
Locates a misplaced handset.
Toggles the registration mode.
Resets the base station to factory settings.
Indicates the mode of the base station:
Fast flashes green when the base station is in the
paging mode.
Slow flashes green when the base station is in the
registration mode.
Illuminates solid green when there is at least one
handset registered to the base station.
Indicates the network status:
Status Slow flashes green when the network is
unavailable.
Illuminates solid green when the network is
Indicates the power status of the base station:
available.
Slow flashes green when the base station is during
the firmware upgrading process.
Indicator Slow flashes green when the base station is during
the resetting process.
Illuminates solid green when the base station is
powered on.
Handset Description
The main hardware components of the W52P/W52H handset are the LCD
screen and the keypad.
Item
Earpiece
LCD Screen
Soft Keys
Speakerphone
Key
Headset
Connector
Off-hook Key
Keypad
Star Key
Redirect Key
Microphone
⑪
Mute Key
⑫
Pound Key
Description
Outputs audio during the earpiece call.
Shows call information, handset status icons,
prompt messages and so on.
Label automatically to identity their contextsensitive features.
Switches between the earpiece and speakerphone
modes.
Answers an incoming call.
Connects a headset.
Answers an incoming call.
Enters the redial call list.
Places a call.
Provides digits, letters and special characters in
context-sensitive applications.
Enters the star symbol.
Switches the silent mode on or off.
Transfers a call to another party.
Picks up audio during earpiece and hands-free
calls.
Toggles Mute feature on or off.
Enters the pound symbol.
Locks or unlocks the handset keypad.
Switches the input method.
⑬
On-hook
Key/Power key
Long presses in the menu screen to return to the
idle screen.
Long presses to turn the handset on or off when
the handset is idle.
Cancels actions or ends a call.
Rejects an incoming call.
⑭
Message Key
Indicates a new receiving voice mail or a missed
call.
Accesses the voice mail or the missed call list.
⑮
Move the cursor.
Act as shortcuts.
Scroll through the displaying information.
Item
Description
Move the cursor.
Act as shortcuts.
Adjust the ringer volume.
Switch the values.
Handset Registration
You can register up to 5 handsets to one W52P base station.
The original handset included in the W52P package is pre-registered to the base station. After
charging, the handset is ready for use.
To register a handset manually:
1. Long press
on the base station.
The registration LED slow flashes, indicating the base station is in the registration
mode.
2. Press
on the handset to enter the main menu.
3. Select
- >Registration->Register Handset.
The LCD screen displays the Base1-Base4.
4. Press
or
to highlight the desired one, and then press the OK soft key.
The handset begins to search for the base station.
5. Press the OK soft key when the LCD screen displays the RFPI code of the base
station.
6. Enter the system PIN (default: 0000).
7. Press the Done soft key.
The handset plays a warning tone and prompts “Handset Subscribed”, which
indicates the handset is registered successfully.
After successful registration, an internal handset number and handset name
appear on the LCD screen.
You can also enable the registration mode of the base station via web user
interface at the path Status->Handset&VoIP->Registered New Handsets.
To de-register a handset via phone user interface:
1. Press
to enter the main menu.
2. Select
- >Registration->De-reg. Handset.
3. Enter the system PIN (default: 0000).
4. Press the Done soft key.
The LCD screen displays the names of the handsets registered to the same base
station. The name of the handset itself is highlighted and followed by a left arrow.
5. Press
or
to highlight the desired handset name, and then press the OK
soft key.
The LCD screen prompts “De-register Handset”.
6. Press the Yes soft key to de-register the handset or the No soft key to cancel.
To select the base station:
1. Press
to enter the main menu.
2. Select
->Registration->Select Base.
The LCD screen displays all base stations the handset registered to and the
Bestbase option (if the handset is registered to more than one base station). The
radio box of the currently used base station is marked. You can select Bestbase
to search for the base station with the best signal strength.
Adjusting Ringer Volume
You can adjust the ringer volume of your handset according to the noise level
of the surrounding environment. The ringer volume can be adjusted using the
menu or the predefined shortcuts (left and right navigation keys) on the
keypad when the handset is idle. The handset supports 5 different ringer
volume levels. The default level is 3.
To adjust ringer volume using the predefined shortcuts:
1. Press
Press
or
when the handset is idle.
to decrease the ringer volume, or press
to increase the ringer volume.
2. Press the Save soft key to accept the change or the Back soft key to cancel.
Locking/Unlocking Keypad
You can lock the handset keypad to prevent keys from being accidentally
pressed.
To lock the keypad:
1. Long press
when the handset is idle until the LCD screen prompts “Keypad
Locked, Press and hold ‘#’ to unlock!”.
The keypad is locked and the
icon appears on the status line.
You can still answer or reject incoming calls as usual. You can also end the
answered call by pressing
.
To unlock the keypad:
1. Long press
again until the LCD screen prompts “Keypad Unlocked”.
The keypad is unlocked and the
Icon disappears from the idle screen.
Locating a Handset
You can locate a misplaced handset using the base station to which the
handset is registered.
To locate a handset:
1. Press
on the base station.
All handsets registered to this base station will ring simultaneously (Paging) and
display the IP address of the base station on the LCD screen.
This helps you locate your handset easily.
You can press any key on the handset or press
again on the base station to
end paging.
You can also locate handsets via web user interface at the path Status>Handset&VoIP->Paging.
Switching Silent Mode On/Off
If the silent mode is switched on, the handset will not ring when receiving an
incoming call, but you can still see the incoming call information on the LCD
screen. You can switch the silent mode on if you do not want to be disturbed.
To switch the silent mode on:
1. Long press
until the LCD screen prompts “All Ring Tones Off”.
The silent mode is on. The
icon appears on the status line.
To switch the silent mode off:
1. Long press
again until the LCD screen prompts “All Ring Tones On”.
The silent mode is off. The
icon disappears from the status line.
Handset Name
The handset will be assigned a name by default if successfully registered to
the base station. You can personalize the handset name.
To rename the handset:
1. Press
to enter the main menu.
2. Select
- >Handset Name.
3. Edit the current name in the Rename field.
4. Press the Save soft key to accept the change.
Language
The handset supports displaying text in different languages. The handset
supports 12 languages: English, French, Turkish, Portuguese, Spanish, Italian,
Deutsch, Polski, Czech, Swedish, Hebrew and Russian. The default language
of the handset is English. You can change the language according to your
requirement.
To change the language of the handset:
1. Press
to enter the main menu.
2. Select
-
3. Press
or
>Language.
to highlight the desired language and press the Select soft
key.
The LCD screen prompts “Change phone language to xxx?” (xxx is the language
you selected).
4. Press the Yes soft key to accept the change.
Text displayed on the handset will change to the selected language.
Ring Tones
Ring tones are used to indicate incoming calls. You can set different ring
tones to distinguish the incoming lines from each other on your handset. You
can also set a ring tone for an incoming intercom call. When receiving an
incoming call, the handset rings the specified ring tone.
To configure ring tones:
1. Press
to enter the main menu.
2. Select
->Audio->Ring Tones->Melodies.
3. Press
4. Press
or
or
to highlight the Intercom Call option or the desired line.
to select and listen to the desired ring tone.
5. Press the Save soft key to accept the change or the Back soft key to cancel.
To adjust ringer volume using the menu:
1.
Press
to enter the main menu.
2.
Select
->Audio->Ring Tones->Volume.
3.
Press
4.
Press the Save soft key to accept the change or the Back soft key to cancel.
or
to decrease/increase the ringer volume.
Backlight
Handset backlight status in the charging state or out of the charging state can
be configured independently of each other. If enabled, the backlight is always
on. Otherwise, the backlight is turned off after the handset is idle for a period
of time. But the backlight is automatically turned on when an incoming call
arrives, a key is pressed or the status of handset changes. You can disable the
backlight to save power.
To configure the backlight:
1. Press
to enter the main menu.
2. Select
->Display->Display Backlight.
3. Press
or
to select the desired value from the In Charger field.
4. Press
or
to select the desired value from the Out Of Charger field.
5. Press the Save soft key to accept the change or the Back soft key to cancel.
Date and Time
Date and time are displayed on the idle screen of your handset. The handset
obtains the date and time from the Simple Network Time Protocol (SNTP)
server by default. If your handset cannot obtain the date and time from the
SNTP server, you need to configure the date and time manually.
To configure date and time manually:
1. Press
to enter the main menu.
2. Select
->Date & Time.
3. Edit the current values in the Date and Time fields respectively.
4. Press the Save soft key to accept the change.
The date and time displayed on the LCD screen will change accordingly.
To configure the time format:
1. Press
2. Select
3. Press
to enter the main menu.
->Display->Time Format.
or
to highlight the desired time format.
4. Press the Change soft key.
The radio box of the highlighted time format is marked.
The time format displayed on the LCD screen will be changed accordingly.
To configure the date format:
1. Press
to enter the main menu.
2. Select
3. Press
->Display->Date Format.
or
to highlight the desired date format.
4. Press the Change soft key.
The radio box of the selected date format is marked.
The date format displayed on the LCD screen will be changed accordingly.
To configure the DST automatically via web user interface:
1.
Click on Phone->Preference.
2.
Mark the Automatic radio box in the Daylight Saving Time field.
Call History Management
Call history contains call information such as calling/called party
identification, time and date, and call duration. The handset maintains call
history lists of All Calls, Outgoing Calls, Missed Calls and Accepted Calls.
Each call history list can store a list of entries sorted by date and time of the
call, starting with the latest call entry. You can check the detailed information
of an entry in the call history. You can also dial a call, add an entry to the
local directory or blacklist, and delete entries from the call history.
To check the local call history:
1. Press the History soft key when the handset is idle.
The LCD screen displays 4 call history lists: All Calls, Outgoing Calls, Missed
Calls and Accepted Calls.
2. Press
or
to highlight the desired list, and then press the OK soft key.
The LCD screen displays all entries of the selected list.
3. Press
or
to highlight the desired entry, and then press the View soft
key.
The LCD screen displays the detailed information of the entry.
To add an entry to the blacklist from the call history:
You can block the incoming calls from the entry by adding it to the blacklist.
1. Press the History soft key when the handset is idle.
The LCD screen displays 4 call history lists: All Calls, Outgoing Calls, Missed
Calls and Accepted Calls.
2. Press
or
to highlight the desired list, and then press the OK soft key.
The LCD screen displays all entries of the selected list.
3. Press
or
to highlight the desired entry.
4. Press the Options soft key, and select Add To Blacklist.
The LCD screen prompts “Are you sure?”.
5. Press the Yes soft key to add the selected entry to the blacklist or the No soft
key to cancel.
To delete an entry from the call history:
1. Press the History soft key when the handset is idle.
The LCD screen displays 4 call history lists: All Calls, Outgoing Calls, Missed
Calls and Accepted Calls.
2. Press
or
to highlight the desired list, and then press the OK soft key.
The LCD screen displays all entries of the selected list.
3. Press
or
to highlight the desired entry.
4. Press the Options soft key, and select Delete.
The selected entry is deleted successfully.
To delete all entries of a list from the call history:
1. Press the History soft key when the handset is idle.
The LCD screen displays 4 call history lists: All Calls, Outgoing Calls, Missed
Calls and Accepted Calls.
2. Press
or
to highlight the desired list, and then press the OK soft key.
The LCD screen displays all entries of the selected list.
3. Press the Options soft key, and then select Delete All.
The LCD screen prompts “Delete All?”.
4. Press the Yes soft key to delete all entries of the selected list or the No soft key
to cancel.
To place a call from the call history:
1. Press the History soft key when the handset is idle.
The LCD screen displays 4 call history lists: All Calls, Outgoing Calls, Missed
Calls and Accepted Calls.
2. Press
or
to highlight the desired list, and then press the OK soft key.
The LCD screen displays all entries of the selected list.
3. Press
4. Press
or
.
to highlight the desired entry.
Incoming Lines
After the handset is registered to the base station, you can assign one or more
incoming lines for the handset. The handset can only receive incoming calls of
the assigned incoming line(s). You can assign incoming lines to all handsets
registered to the same base station on your handset.
To assign the incoming line to handsets:
1. Press
to enter the main menu.
2. Select
-
>Telephony->Incoming Lines.
3. Enter the system PIN (default: 0000).
4. Press the Done soft key.
The LCD screen displays all handsets registered to the base station. The handset itself
is highlighted and followed by a left arrow.
5. Press
6. Press
or
or
to highlight the desired handset, and then press the OK soft key.
to select Accept from the desired line fields.
7. Press the Save soft key to accept the change.
8. Press the Back soft key to return to the previous screen.
9. Repeat steps 5-8 to assign incoming lines for other handsets.
If a line is assigned to multiple handsets as an incoming line, an incoming call to this
line will cause these handsets to ring simultaneously, but the incoming call can be only
answered by one of them.
Auto Answer
When auto answer feature is enabled, you can simply answer the incoming calls
by picking up the handset from the charger cradle without having to press the offhook key. The auto answer feature works only if the handset is placed in the
charger cradle.
To configure auto answer:
1. Press
to enter the main menu.
2. Select
->Telephony->Auto Answer.
3. Press the Change soft key to check or uncheck the Auto Answer checkbox.
Auto Intercom
Intercom is a useful feature in an office environment to quickly connect with the
operator or the secretary. You can make internal intercom calls and external
intercom calls on the phone. Internal intercom calls are made between handsets
registered to the same base station. External intercom calls can be made by
dialing *96<extension>
The handset can automatically answer an incoming external intercom call and
play warning tone only when there is only one handset subscribed and no call in
progress on the handset.
To automatically answer an incoming internal intercom call, you need to enable
auto intercom feature on the handset. The following configuration types of auto
intercom feature are available for selection:
!
On (Beep On): Auto intercom feature is on. The handset will answer an incoming
internal intercom call automatically and play a warning tone.
!
On (Beep Off): Auto intercom feature is on. The handset will answer an incoming
internal intercom call automatically without a warning tone.
!
Off: Auto intercom feature is off. You need to answer an incoming internal intercom
call by pressing the Accept soft key.
To configure auto intercom:
1. Press
2. Select
to enter the main menu.
->Telephony->Auto Intercom.
The LCD screen displays three configuration types.
3. Press
or
to highlight the desired configuration type.
4. Press the Change soft key.
The radio box of the selected configuration type is marked.
Placing Calls
You can use your handset to place an internal or external call. You can place a
call using the following call modes:
Earpiece mode—pressing the off-hook key to dial out.
!
Speakerphone mode—pressing the speakerphone key to dial out.
!
Headset mode—connecting a headset.
During the call, you can switch the call mode by pressing the corresponding keys
or connecting a headset.
You can cancel the dialing operation by pressing the on-hook key. During the call
conversation, you can press the left and right navigation keys to adjust the volume
of the currently engaged audio devices (earpiece, headset or loudspeaker). The
call duration is displayed on the LCD screen while the call is in progress.
!
Placing Internal Calls
You can make free internal calls between the handsets registered to the same base
station. You can place an internal call to one handset or all handsets registered to
the same base station.
To place an internal call to one handset:
1. Press
to enter the main menu.
2. Select
.
The LCD screen displays all other registered handset names and the All HS option.
3. Press
4. Press
or
,
to highlight the desired handset name.
,
or the OK soft key to dial out.
To place an internal call to all handsets:
1. Press
to enter the main menu.
2. Select
.
The LCD screen displays all registered handset names and the All HS option.
3. Select All HS.
4. Press
,
,
or the OK soft key to dial out.
All other subscribed handsets will ring simultaneously.
Placing External Calls
To place an external call:
You can do one of the following:
-
Enter the desired number using the keypad.
Press
,
or
to dial out.
If there are multiple lines assigned to your handset as outgoing lines, press the Line
soft key to select the desired line and then press
or the Dial soft key to dial out.
If you do not select a line, the handset uses the default outgoing line to dial out.
-
Press
to enter the pre-dialing screen.
Enter the desired number using the keypad.
Press
,
or
to dial out.
If there are multiple lines assigned to your handset as outgoing lines, press the Line
soft key to select the desired line and then press
or the Dial soft key to dial out. If
you do not select a line, the handset uses the default outgoing line to dial out.
To place a new call during an active call:
You can place at most two calls on your handset.
1. Press the Ext.Call soft key.
The active call is placed on hold.
2. Enter the desired number in the Call To field using the keypad.
3. Press
,
or
to dial out.
Answering Calls
You can answer a call in three ways:
!
!
!
Using the earpiece
Using the speakerphone
Using the headset
To answer a call using the earpiece:
1. Press
or the Accept soft key.
To answer a call using the speakerphone mode:
1. Press
.
To answer a call using the headset:
1. With a headset connected, press the Accept soft key.
Answering When in Another Call
If you are during an active call, an incoming call arrives on the handset, do the
following:
1. Press
,
,
or the Accept soft key.
The incoming call is answered, and the original call is placed on hold.
Ending Calls
To end a call:
Do one of the following:
-
Press
-
Place the handset in the charger cradle.
.
Redialing Calls
The redial number list stores the twenty last dialed phone numbers. When the
memory of the redial number list is full, the handset will automatically erase the
oldest dialed number when a new number is dialed. You can redial a call from the
redial number list.
To redial the last dialed number:
1. Press
when the handset is idle.
2. Press
again.
A call to your last dialed number is attempted.
To redial a previously dialed number:
1. Press
when the handset is idle.
The handset displays the dialed phone numbers.
2. Press
or
to highlight the desired entry.
You can press Options->Edit Before Call to edit the phone number or select the
desired line by pressing the Line soft key.
3. Press
again.
You can add local contacts from the redial number list. You can also delete an
entry or all entries from the redial number list.
Call Mute
You can mute the microphone during an active call. When muting the
microphone, you can hear the other party but he or she cannot hear you. For
example, if you do not want the other party to listen to the conservation when you
talk to someone in the room, you can mute the microphone temporarily.
To mute a call:
1. Press
during an active call.
The call is muted, and the
icon is displayed on the LCD screen.
To un-mute a call:
1. Press
The
again.
icon disappears from the LCD screen.
Call Hold/Resume
You can place an active call on hold. At any time, at most one active call can be
in progress on your handset. You can answer or make another call while placing
the original call on hold.
To place a call on hold:
1. Press the Options soft key during a call, and then select Hold.
The call is placed on hold and the
icon is displayed on the LCD screen.
To resume a hold call:
Do one of the following:
-
Press the Resume soft key.
-
Press
.
-
Press
.
Two calls on Hold:
If two calls are placed on hold on the handset, press the Resume soft key to
resume the current call. Press
or the Swap soft key to swap between two
calls.
Call Waiting
You can enable or disable call waiting feature on the handset. If call waiting
feature is enabled, the handset will notify you of a new incoming call during a
call, and present the incoming call information visually on the LCD screen. You
can also enable the handset to play a warning tone when receiving a new
incoming call during a call. If call waiting feature is disabled, the new incoming
call will be automatically rejected by the handset.
To configure call waiting feature:
1. Press
to enter the main menu.
2. Select
->Call Waiting.
3. Press
or
to select the desired value from the Status field.
4. Press
or
to select the desired value from the Tone field.
5. Press the Save soft key to accept the change or the Back soft key to cancel.
6.
To answer a new incoming call during a call:
If call waiting feature is enabled, a new incoming call can be answered during a
call.
1. Press the Accept soft key to answer the new incoming call.
The original call is placed on hold.
Do Not Disturb (DND)
You can activate or deactivate the DND mode on a per-line basis. If DND mode
is activated for a specific line, all incoming calls to the line will be rejected
automatically, and the callers will hear a busy tone.
To activate DND mode for a specific line:
1. Press
to enter the main menu.
2. Select
->Do Not Disturb.
The LCD screen displays the incoming lines currently assigned to the handset.
3. Press
4. Press
or
or
to highlight the desired line, and then press the OK soft key.
to select Enabled from the Status field.
5. Press the OK soft key to accept the change.
The
icon on the status line indicates the DND mode is activated. You can
press the Line soft key when the handset is idle to check the line status. The
icon in the bottom of a line indicates that the DND mode is activated for this line.
The handset will reject all incoming calls to this line, and the LCD screen
displays the
missed call icon followed by the number of missed calls.
Call Forward
You can enable call forward feature on a per-line basis. The handset will forward
incoming calls of the line to another party.
Three forwarding types:
!
!
!
Always Forward: Incoming calls are immediately forwarded.
Busy Forward: Incoming calls are immediately forwarded if the line is busy.
No Answer Forward: Incoming calls are forwarded if not answered after a
period of time.
To enable call forward feature for a specific line:
1. Press
to enter the main menu.
2. Select
->Call Forward.
The LCD screen displays the incoming lines currently assigned to the handset.
3. Press
or
to highlight the desired line, and then press the OK soft key.
4. Press
or
to highlight the desired forwarding type, and then press the OK
soft key.
5. Press
or
to select Enabled from the Status field.
6. Enter the destination number you want to forward incoming calls to in the Target
field.
7. Press or
to select the desired ring time to wait before forwarding from the After
Ring Time field (only available for No Answer Forward).
8. Press the Save soft key to accept the change.
The icon on the status line indicates call forward feature is enabled.
If Always Forward is selected, there is no prompt on the LCD screen when the
line receives an incoming call. The incoming call is logged in the Accepted Calls
list.
Call Transfer
You can transfer a call to another party in one of the following ways:
!
!
!
Blind Transfer: Transfer a call directly to another party without consulting.
Semi-Attended Transfer: Transfer a call when receiving the ring-back.
Attended Transfer: Transfer a call with prior consulting.
To perform a blind transfer:
1. Press the Options soft key during a call, and then select Transfer.
You can also press
directly.
2. Enter the number or select the handset you want to transfer the call to.
3. Press
or the Transfer soft key.
The call is connected to the number or the handset you specified, and the LCD screen
prompts “Call Transferred”.
To perform a semi-attended transfer:
1. Press the Options soft key during a call, and then select Transfer.
You can also press
directly.
2. Do one of the following:
-
Enter the number or select the handset you want to transfer the call to.
Press
-
to dial out.
Press the Directory soft key, and then select the desired contact.
Press
or the Call soft key.
If both the office number and the mobile number of the contact are stored,
select the desired number and press
or the OK soft key to dial out.
3. Press
back.
or the Transfer soft key to complete the transfer when receiving the ring-
The LCD screen prompts “Call Transferred”.
To perform an attended transfer:
1. Press the Options soft key during a call, and then select Transfer.
You can also press
directly.
2. Do one of the following:
-
Enter the number or select the handset you want to transfer the call to.
Press
-
to dial out.
Press the Directory soft key, and then select the desired contact.
Press
or the Call soft key.
If both the office number and the mobile number of the contact are stored,
select the desired number and press
or the OK soft key to dial out.
3. Press
the call.
or the Transfer soft key to complete the transfer after the party answers
The LCD screen prompts “Call Transferred”.
Local Conference
You can use the handset to create a local conference with other parties. The
handset supports up to 3 parties (including yourself) in a conference call. You can
create a conference between an active call and a held call on the handset (on the
same line or different lines).
To set up a local conference call:
1. Place a call to the first party.
2. Press the Options soft key, and then select Conference.
3. Do one of the following:
-
Enter the number of the second party or select the handset you want to add to
the conference.
Press
-
,
,
or the Conf. soft key to dial out.
Press the Directory soft key, and then select the desired contact.
Press
,
,
or the Call soft key.
If both the office number and the mobile number of the contact are stored,
select the desired number and press
,
,
or the OK soft key to dial
out.
4. When the second party answers the call, you can consult with him or her before
adding the call to the conference.
5. Press the Conf. soft key again to join all parties in the conference.
To join two calls in a conference:
1. Place two calls on the handset.
2. Select the desired call and make sure the call is active.
3. Press the Options soft key, and then select Conference.
Two calls are joined in the conference.
Listen To Voicemail
1. Press
to enter the main menu.
2. Select
->Play Message.
The LCD screen displays the lines assigned to the handset as incoming lines and
outgoing lines simultaneously, and the number of voice mails for each line.
To listen to the voice mail via fast access:
1. Long press
when the handset is idle.
The handset automatically dials out the voice mail access code using the line you
selected when configuring fast access for voice mail.
2. Follow the voice prompt from the system server to listen to your voice mails.
You can also listen to the voice mail by pressing to enter the Messages & Calls
screen. Select the desired line and press the Select soft key.