Table of Contents
Table of Contents.............................1
Usage Notice....................................2
Safety Information................................2
Precautions..........................................3
Eye Safety Warnings...........................5
Product Features.................................5
Introduction.......................................6
Package Overview...............................6
Product Overview................................7
Main Unit............................................... 7
Control Panel........................................ 8
Input/Output Connections..................... 9
Remote Control................................... 10
SETUP................................................ 36
SETUP | Audio Settings...................... 38
SETUP | Advanced............................. 39
OPTIONS............................................ 40
OPTIONS | Advanced......................... 42
OPTIONS | Lamp Settings.................. 43
OPTIONS | Optional Filter Settings.... 44
Appendices.....................................45
Troubleshooting.................................45
Replacing the Lamp...........................51
Installing and Cleaning the Dust
Filter...................................................53
Compatibility Modes..........................54
Connecting the Projector...................11
Computer/Video/HDMI/Mac
Compatibility....................................... 54
3D Input Video Compatibility.............. 55
Connect to Computer/Notebook......... 11
Connect to Video Sources.................. 12
RS232 Commands and Protocol
Function List......................................56
Powering the Projector On / Off.........13
RS232 Pin Assignments..................... 56
RS232 Protocol Function List............. 57
Installation...................................... 11
Powering On the Projector.................. 13
Powering off the projector................... 14
Warning Indicator................................ 14
Ceiling Mount Installation...................61
Regulation & Safety Notices..............62
Adjusting the Projected Image...........15
Adjusting the Projector’s Height ........ 15
Adjusting the Projector’s Zoom /
Focus.................................................. 16
Adjusting Projection Image Size......... 16
User Controls.................................18
Control Panel & Remote Control.......18
Control Panel...................................... 18
Remote Control Battery Installation.... 19
Remote Control................................... 20
On-screen Display Menus.................24
How to operate................................... 24
Menu Tree........................................... 25
IMAGE................................................ 27
IMAGE | Advanced............................. 29
IMAGE | Advanced | Signal (RGB) .... 31
DISPLAY............................................. 32
DISPLAY | 3D .................................... 35
1
English
Usage Notice
Safety Information
The lightning flash with arrow head within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Important Safety Instruction
1.Do not block any ventilation openings. To ensure reliable operation of
the projector and to protect from over heating, it is recommended to
install the projector in a location that does not block ventilation. As an
example, do not place the projector on a crowded coffee table, sofa,
bed, etc. Do not put the projector in an enclosure such as a book case
or a cabinet that restricts air flow.
2.Do not use the projector near water or moisture. To reduce the risk
of fire and/or electric shock, do not expose the projector to rain or
moisture.
3.Do not install near heat sources such as radiators, heaters, stoves or
any other apparatus such as amplifiers that emits heat.
4.Clean only with dry cloth.
5.Only use attachments/accessories specified by the manufacturer.
6. Do not use the unit if it has been physically damaged or abused.
Physical damage/abuse would be (but not limited to):
 Unit has been dropped.
 Power supply cord or plug has been damaged.
 Liquid has been spilled on to the projector.
 Projector has been exposed to rain or moisture.
 Something has fallen in the projector or something is loose inside.
Do not attempt to service the unit yourself. Opening or removing covers
may expose you to dangerous voltages or other hazards. Please call
InFocus before you send the unit for repair.
7.Do not let objects or liquids enter the projector. They may touch
dangerous voltage points and short out parts that could result in fire or
electric shock.
8.See projector enclosure for safety related markings.
9.The unit should only be repaired by appropriate service personnel.
English
2
Usage Notice
Precautions
Please follow all warnings, precautions and
maintenance as recommended in this user’s
guide.
▀■ Warning- Do not look into the projector’s lens when the lamp is
on. The bright light may hurt and damage your eyes.
▀■ Warning- To reduce the risk of fire or electric shock, do not
expose this projector to rain or moisture.
▀■ Warning- Please do not open or disassemble the projector as
this may cause electric shock.
▀■ Warning- When replacing the lamp, please allow the unit to
cool down. Follow instructions as described on pages
51-52.
▀■ Warning- This projector will detect the life of the lamp itself.
Please be sure to change the lamp when it shows
warning messages.
▀■ Warning- Reset the “Lamp Reset” function from the on-screen
display “OPTIONS | Lamp Settings” menu after
replacing the lamp module (refer to page 43).
▀■ Warning- When switching the projector off, please ensure
When the lamp
reaches the end
of its life, the projector will not turn
back on until the
lamp module has
been replaced.
To replace the
lamp, follow the
procedures listed
under “Replacing
the Lamp” section
on pages 51-52.
the cooling cycle has been completed before
disconnecting power. Allow 90 seconds for the
projector to cool down.
▀■ Warning- Do not use lens cap when projector is in operation.
▀■ Warning- When the lamp is approaching the end of its lifetime,
the message “Lamp Warning: Lamp life exceeded.”
will show on the screen. Please contact your local
reseller or service center to change the lamp as soon
as possible.
3
English
Usage Notice
Do:
 Turn off and unplug the power plug from the AC outlet before
cleaning the product.
 Use a soft dry cloth with mild detergent to clean the display
housing.
 Disconnect the power plug from AC outlet if the product is
not being used for a long period of time.
Do not:
 Block the slots and openings on the unit provided for
ventilation.
 Use abrasive cleaners, waxes or solvents to clean the unit.
 Use under the following conditions:
- In extremely hot, cold or humid environments.
Ensure that the ambient room temperature is within
5 - 40°C.
Relative Humidity is 5 - 40°C, 80% (Max.),
English
4
non-condensing.
- In areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
Usage Notice
Product Features
▀■ SVGA (800x600) / XGA (1024x768) / WXGA
(1280X800) Native resolution
▀■ HD compatible – 720p and 1080p supported
▀■ BrilliantColorTM Technology
▀■ Kensington Lock
™™ (*) For models with
HDMI Input.
™™ Product features may
vary depending on
model.
▀■ RS232 control
▀■ Rapid shutdown
▀■ Full 3D(*) (See page 55)
▀■ The Product Features shall be configured by the manufacturer as per practical conditions.
5
English
Introduction
Package Overview
Unpack and inspect the box contents to ensure
all parts listed below are in the box. If something
is missing, please contact your nearest customer
service center.
Projector
Power Cord
VGA Cable(*)
VGA
Enter
CR2025
3V
Due to different
applications in
each Country,
some regions
may have
different
accessories.
(*) The accessory depends on
model’s specifications.
English
6
Battery
Documentation :
User’s Manual

Warranty Card

Quick Start Card

WEEE Card

(for EMEA only)
Menu
Zoom
IR Remote Control
Carrying case(*)
Introduction
Product Overview
Main Unit
11
1
2
1
4
3
5
6
10
8
7
9
The interface
is subject to
model’s specifications.
Do not block
projector in/out
air vents.
1. Focus Ring
2. Zoom Lever
3. IR Receiver
4. Control Panel
5. Input / Output Connections
6. KensingtonTM Lock Port
7. Ventilation (inlet)
8. Speaker
9. Lens Cap
10. Tilt-Adjustment Feet
11. Ventilation (outlet)
7
English
Introduction
Control Panel
1
2
3
4
11
5
6
10
9
8
1. Source
2. Keystone Correction
3. Enter
4. Re-Sync
5. Help
6. Four Directional Select Keys
7. Temp LED
8. Power
9. On/Standby LED
10. Lamp LED
11. Menu
English
8
7
Introduction
Input/Output Connections
3
™™ Monitor loop
through only support in VGA2-IN/
YPbPr.
™™ The interface is
subject to model’s
specifications.
8
6
VGA1-IN/YPbPr
RS-232C
USB
AUDIO1-IN
9
5
HDMI
VGA-OUT
VIDEO
AUDIO2-IN
AUDIO-OUT
7
4
VGA2-IN/YPbPr
2
S-VIDEO
1
10
11
12
13
1.
2.
3.
4.
Composite Video Input Connector
S-Video Input Connector
VGA-Out Connector (Monitor Loop-through Output)
VGA2-IN/YPbPr Connector
(PC Analog Signal/Component Video Input/HDTV/YPbPr)
5. VGA1-IN/YPbPr Connector
(PC Analog Signal/Component Video Input/HDTV/YPbPr)
6. HDMI Connector
7. Security Lock Slot
8. Audio2 Input Connector (3.5mm mini jack)
9. Audio Output Connector ( 3.5mm mini jack)
10. Audio1 Input Connector (3.5mm mini jack)
11. RS-232 Connector (9-pin)
12. USB Connector (Connect to PC for Remote Mouse function/USB Service for firmware upgrade)
13. Power Socket
9
English
Introduction
Remote Control
The interface is
subject to model’s
specifications.
11
1
12
2
3
VGA
4
14
5
15
6
6
Enter
16
7
8
9
10
25
20
LT
R
3V
O
C
English
S
™™ Before using the
remote control
for the first time,
remove the transparent insulation
tape. See page
19 for battery
installation.
10
13
Menu
Zoom
17
14
18
1.
2.
3.
4.
5.
6.
7.
Source
Re-Sync
Video and S-Video
HDMI
3D
Volume +/Four Directional Select
Keys
8. Menu
9. AV Mute
10. Mute
11. IR LED Indicator
12. Power On/Off
13. VGA
14. Keystone +/15. Aspect
16. Enter
17. Zoom
18. Brightness Mode
Installation
Connecting the Projector
Connect to Computer/Notebook
Monitor Output
Audio Output
The interface is
subject to model’s
specifications .
VGA1-IN/YPbPr
5
HDMI
VGA2-IN/YPbPr
4
USB
AUDIO1-IN
RS-232C
VGA-OUT
VIDEO
3
molex
6
MOLEX
(*) Optional
accessory
AUDIO-OUT
Due to the
difference in
applications for
each country,
some regions may
have different
accessories.
AUDIO2-IN
1
S-VIDEO
2
7
8
1......................................................................................*Audio Output Cable
2.............................................................................................*VGA Out Cable
3.....................................................................................................VGA Cable
2..................................................................................................*HDMI Cable
5....................................................................................................Power Cord
6....................................................................................................*USB Cable
7................................................................................................*RS232 Cable
8.........................................................................................*Audio Input Cable
11
English
Installation
Connect to Video Sources
Composite Video Output
S-Video Output
1
DVD Player, Set-top Box,
HDTV receiver
2
RS-232C
VGA1-IN/YPbPr
4
USB
HDMI
VGA2-IN/YPbPr
VGA-OUT
AUDIO1-IN
AUDIO-OUT
AUDIO2-IN
VIDEO
S-VIDEO
3
8
Due to the
difference in
applications for
each country,
some regions may
have different
accessories.
5
6
(*) Optional
accessory
The interface is
subject to model’s
specifications .
Audio Output
7
9
DVD Player, Set-top Box,
HDTV receiver
1................................................................................*Composite Video Cable
2.............................................................................................. *S-Video Cable
3..................................................................................................*HDMI Cable
4....................................................................................................Power Cord
5......................................................................................*Audio Output Cable
6.........................................................................................*Audio Input Cable
7...........................................................................................*VGA/RCA Cable
8................................................*15-Pin to 3 RCA Component/HDTV Adaptor
9.............................................................................*3 RCA Component Cable
English
12
Installation
Powering the Projector On / Off
Powering On the Projector
1. Remove the lens cap. 
2. Securely connect the power cord and signal cable. When
connected, the ON/STANDBY LED will turn Amber.

When Power mode
3.
Turn on the lamp by pressing “ ” button either on the top of
(Standby) is set to
the projector or on the remote. The ON/STANDBY LED will
Eco (<0.5W), the
now turn Green. 
VGA output and
Audio pass-through The startup screen will display in approximately 10 seconds.
will be deactivated
The first time you use the projector, you will be asked to
when the projector is
select the preferred language and power saving mode.
in standby.
4. Turn on and connect the source that you want to display
on the screen (computer, notebook, video player, etc). The
projector will detect the source automatically. If not, push
menu button and go to “OPTIONS”.
Make sure that the “Source Lock” has been set to “Off”.
If you connect multiple sources at the same time, press the
“SOURCE” button on the control panel or direct source keys
on the remote control to switch between inputs.
2
Turn on the
projector first and
then select the
signal sources.
1
Power
Lens Cap
13
English
Installation
Powering off the projector
1. Press the “ ” button on the remote control or on the
control panel to turn off the projector.
The following message will be displayed on the screen.
Press the “ ” button again to confirm otherwise the
message will disappear after 15 seconds. When you pressing for the second time, the projector will shut down.
2. The cooling fans continue to operate for about 10 seconds
for cooling cycle and the ON/STANDBY LED will Flash
Green. When the ON/STANDBY LED lights solid Amber,
the projector has entered standby mode.
If you wish to turn the projector back on, you must wait until
the projector has completed the cooling cycle and has entered standby mode. Once in standby mode, simply press “
” button to restart the projector.
3. Disconnect the power cord from the electrical outlet and the
projector.
4. Do not turn on the projector immediately following a power
off procedure.
Warning Indicator
Contact the
nearest service
center if the
projector displays
these symptoms.
See pages
64-65 for more
information.
English
14
When the warning indicators (see below) come on, the
projector will automatically shutdown:
 “LAMP” LED indicator is lit red and if “On/Standby” indicator
flashes amber.
 “TEMP” LED indicator is lit red and if “On/Standby”
indicator flashes amber. This indicates the projector has
overheated. Under normal conditions, the projector can be
switched back on.
 “TEMP” LED indicator flashes red and if “On/Standby”
indicator flashes amber.
Unplug the power cord from the projector, wait for 30 seconds
and try again. If the warning indicator light up again, please
contact your nearest service center for assistance.
Installation
Adjusting the Projected Image
Adjusting the Projector’s Height
The projector is equipped with elevator feet for adjusting
the image height.
1.Locate the adjustable foot you wish to modify on the
underside of the projector.
2. Rotate the adjustable ring clockwise to raise the projector
or counter clockwise to lower it. Repeat with the remaining
feet as needed.
Tilt-Adjustment Feet
Tilt-Adjustment Ring
15
English
Installation
Adjusting the Projector’s Zoom / Focus
You may turn the zoom ring to zoom in or out. To focus the image, rotate the focus ring until the image is clear.
SVGA/XGA series: The projector will focus at distances from
3.94 to 39.36 feet (1.2 to 12.0 meters).
WXGA series: The projector will focus at distances from 3.28
to 32.8 feet (1 to 10 meters).
Zoom Lever
Focus Ring
Adjusting Projection Image Size
SVGA/XGA series: Projection Image Size from 27.5” to
302.8” (0.7 to 7.69 meters).
WXGA series: Projection Image Size from 27.3” to 299.5”
(0.69 to 7.61 meters).
Top View
Screen
Screen (W)
Height
Projection Distance (D)
Screen
Side View
Offset (Hd)
Projection Distance (D)
English
16
Screen (H)
Dia
go
na
Width
l
Installation
SVGA/XGA
Diagonal length
(inch) size of
4:3 Screen
Screen Size W x H
(m)
Projection Distance (D)
(inch)
(m)
Offset (Hd)
(feet)
Width
Height
Width
Height
wide
tele
wide
tele
(m)
(inch)
30.00
0.61
0.46
24.00
18.00
1.19
1.31
3.90
4.30
0.07
2.70
40.00
0.81
0.61
32.00
24.00
1.58
1.75
5.20
5.73
0.09
3.60
60.00
1.22
0.91
48.00
36.00
2.38
2.62
7.80
8.60
0.14
5.40
70.00
1.42
1.07
56.00
42.00
2.77
3.06
9.10
10.03
0.16
6.30
80.00
1.63
1.22
64.00
48.00
3.17
3.50
10.40
11.46
0.18
7.20
90.00
1.83
1.37
72.00
54.00
3.57
3.93
11.70
12.90
0.21
8.10
100.00
2.03
1.52
80.00
60.00
3.96
4.37
13.00
14.33
0.23
9.00
120.00
2.44
1.83
96.00
72.00
4.75
5.24
15.60
17.20
0.27
10.80
150.00
3.05
2.29
120.00
90.00
5.94
6.55
19.50
21.49
0.34
13.50
180.00
3.66
2.74
160.00
120.00
7.92
8.74
25.99
28.66
0.46
18.00
250.00
5.08
3.81
200.00
150.00
9.91
10.92
32.49
35.82
0.57
22.49
300.00
6.10
4.57
240.00
180.00
11.89
13.11
38.99
42.99
0.69
26.99
WXGA
Diagonal length
(inch) size of
16:10 Screen
Screen Size W x H
(m)
Projection Distance (D)
(inch)
(m)
Offset (Hd)
(feet)
Width
Height
Width
Height
wide
tele
wide
tele
(m)
(inch)
30.00
0.65
0.40
25.43
15.90
1.00
1.10
3.26
3.62
0.05
1.99
40.00
0.86
0.54
33.91
21.19
1.33
1.47
4.35
4.83
0.07
2.65
60.00
1.29
0.81
50.87
31.79
1.99
2.21
6.53
7.25
0.10
3.97
70.00
1.51
0.94
59.34
37.09
2.32
2.58
7.62
8.46
0.12
4.64
80.00
1.72
1.08
67.82
42.39
2.65
2.95
8.70
9.66
0.13
5.30
90.00
1.94
1.21
76.30
47.69
2.99
3.31
9.79
10.87
0.15
5.96
100.00
2.15
1.35
84.78
52.99
3.32
3.68
10.88
12.08
0.17
6.62
120.00
2.58
1.62
101.73
63.58
3.98
4.42
13.06
14.50
0.20
7.95
150.00
3.23
2.02
127.17
79.48
4.98
5.52
16.32
18.12
0.25
9.93
180.00
3.88
2.42
152.60
95.38
5.97
6.63
19.58
21.75
0.30
11.92
250.00
5.38
3.37
211.95
132.47
8.29
9.21
27.20
30.20
0.42
16.56
300.00
6.46
4.04
254.33
158.96
9.95
11.05
32.64
36.24
0.50
19.87
This table is for user’s reference only.
17
English
User Controls
Control Panel & Remote Control
Control Panel
Using the Control Panel
English
POWER
Refer to the “Power On/Off the Projector” section on
pages 13-14.
RE-SYNC
Automatically synchronize the projector to the input
source.
ENTER
Confirm your item selection.
SOURCE
Press “SOURCE” to select an input signal.
Menu
Press “Menu” to launch the on-screen display
(OSD) menu. To exit OSD, Press “Menu” again.
Help
Help Menu (only available when OSD menu is not
shown).
Four Directional Select Keys
Use
to select items or make adjustments to your selection.
Keystone
Use
to adjust image distortion caused
by tilting the projector. (±40 degrees)
/
Lamp LED
Indicate the projector’s lamp status.
Temp LED
Indicate the projector’s temperature status.
ON/STANDBY LED
Indicate the projector’s status.
18
User Controls
Remote Control Battery Installation
25
LT
C
R
20
2- L iC E L L 3 V
TS
2. Install new battery into the
compartment. Remove the
old battery and install new
one (CR2025). Ensure that
the side with a “+” is facing
up.
C
R
20
25
O
L
O
M nO
S JAPAN H
1. Press firmly and slide the
battery cover off.
3V
25
20
LT
R
3V
O
C
M
S
3. Put the cover back.
To ensure safe operation, please observe the following precautions :
``
``
``
``
``
Use CR2025 type battery.
Avoid contact with water or liquid.
Do not expose the remote control to moisture or heat.
Do not drop the remote control.
If the battery has leaked in the remote control, carefully wipe
the case clean and install new battery.
`` Risk of an explosion if battery is replaced by an incorrect type.
`` Dispose of used battery according to the instructions.
19
English
User Controls
Remote Control
Using the Remote Control
VGA
Power
Refer to the “Power On/Off the Projector”
section on pages 13-14.
Source
Press “Source” to select an input signal.
Re-Sync
Automatically synchronizes the projector to
the input source.
Video
Press “Video” to choose Composite Video
and S-video source.
HDMI
Press “HDMI” to choose HDMI source. (For
certain model)
3D
Press the “3D” to turn the 3D OSD menu on/
off.
Four Directional
Select Keys
Use
to select items or make
adjustments to your selection.
AV Mute
Momentarily turns off/on the audio and video.
Enter
Confirm your item selection.
Mute
Momentarily turns off/on the audio.
VGA
Press “VGA” to choose VGA sources.
Keystone +/-
Adjust image distortion caused by tilting the
projector.
Aspect
Use this function to choose your desired
aspect ratio.
Menu
Press “Menu” to launch the on-screen display (OSD) menu. To exit OSD, press “Menu”
again.
Volume +/-
Adjust to increase / decrease the volume.
Brightness
Mode
Change the brightness mode: Bright->Eco
->Dynamic. (refer to page 43)
Zoom in on an image.
Enter
Zoom
Menu
The interface
is subject to
model’s specifications.
Zoom
English
20
Press
buttons to alter zoom.
User Controls
Using the HELP button
The HELP function ensures easy setup and operation.
Press the “?” button on the control panel to open the Help
Menu.
21
English
User Controls
Help menu button functions only when no input source
is detected.
Please refer to the
“Troubleshooting”
section on pages
45-50 for more
details.
If input source is detected and help button is pressed, the
following pages will appear to help diagnose any problems.
English
22
User Controls
23
English
User Controls
On-screen Display Menus
The Projector has multilingual On-screen Display menus that
allow you to make image adjustments and change a variety of
settings. The projector will automatically detect the source.
How to operate
1. To open the OSD menu, press “Menu” on the Remote Control or
Projector Keypad.
2 When OSD is displayed, use
keys to select any item in the
main menu. While making a selection on a particular page, press
or “Enter” key to enter sub menu.
3. Use
using
keys to select the desired item and adjust the settings
key.
4. Select the next item to be adjusted in the sub menu and adjust as
described above.
5. Press “Enter” to confirm, and the screen will return to the main
menu.
6. To exit, press “Menu” again. The OSD menu will close and the
projector will automatically save the new settings.
Main Menu
Sub Menu
Settings
English
24
User Controls
Menu Tree
Main Menu
Sub Menu
IMAGE
Display Mode
#1
#1
Settings
Brightness
Contrast
Sharpness
Color
Tint
Advanced
Gamma
BrilliantColorTM
Color Temp.
Color settings
Presentation / Bright / Movie / sRGB /
Blackboard / User / 3D
-50~50
-50~50
1~15
-50~50
-50~50
Film / Video / Graphics / Standard
1~10
Warm / Medium / Cold
Hue / Saturation / Gain
Red / Green / Blue /
Cyan / Magenta /
Yellow
White
Reset
Exit
Red / Green / Blue
Color Space
#3
#2
Signal
Automatic
Phase (VGA)
Frequency (VGA)
H. Position (VGA)
V. Position (VGA)
Exit
AUTO / RGB / YUV
AUTO / RGB (0-255) / RGB (16-235) /
YUV
On / Off
0~31
-5~5
-5~5
-5~5
Exit
Reset
Format
DISPLAY
#4
#5
Edge Mask
Zoom
Image Shift
H
V
V Keystone
3D
#6
#6
3D Mode
3D->2D
3D Format
3D Sync. Invert
Exit
English / Deutsch / Français / Italiano /
Español / Português / Svenska /
Nederlands / Norsk/Dansk / Polski /
Suomi / Ɋɭɫɫɤɢɣ / İȜȜȘȞȚțȐ / Magyar /
ýeština / ̶γέΎϓ / ϲΑέϋ /腎誎襦肫 /
䬨య襦肫 / 螔膩蓳 /䞲ῃ㠊 / ࡷࡎ࡙ /
Türkçe / ViӋt / Bahasa Indonesia / Româ
nå
Language
SETUP
4:3 / 16:9 / Native / AUTO
4:3 / 16:9 or 16:10 / Native / AUTO
0~10
-5~25 (80%~200%)
-100~100
-100~100
-40~40
Off / DLP-Link
3D / L / R
AUTO / SBS / Top and Bottom / Frame
Sequential
On / Off
Projection
Menu Location
#5
#7
Screen Type
Security
Security
Security Timer
Change Password
Exit
16:10 / 16:9
On / Off
Month / Day / Hour
25
English
User Controls
Main Menu
Sub Menu
SETUP
Projector ID
Audio Settings
Advanced
OPTIONS
#7
Input Source
Source Lock
High Altitude
Information Hide
Keypad Lock
Test Pattern
IR Function
Background Color
Advanced
Lamp Settings
Optional Filter Settings
Settings
0~99
Internal Speaker
Mute
Volume
Audio Input
Logo
Closed Captioning
Exit
On / Off
On / Off
0~10
Default / AUDIO1 / AUDIO2
Default / Neutral
Off / CC1 / CC2
#3
Direct Power On
Auto Power Off (min)
Quick Resume
Sleep Timer (min)
Power Mode (Standby)
Exit
Lamp Hours
Lamp Reminder
Brightness Mode
Lamp Reset
Dynamic Dimming
Exit
Optional Filter Installed
Filter Usage Hours
Filter Reminder
Filter Reset
Exit
Reset
VGA1 / VGA2 / Video / S-Video / HDMI
On / Off
On / Off
On / Off
On / Off
None / Grid / White Pattern
On / Off
Black / Red / Blue / Green / White
On / Off
0~180
On / Off
0~990
Active / Eco.
On / Off
Bright / Eco. / Dynamic
Yes / No
On / Off
Yes / No
0~9999
Off / 300hr / 500hr / 800hr / 1000hr
Yes / No
Yes / No
Please note that the on-screen display (OSD) menus vary according to the
signal type selected and the projector model you are using.
(#1) “Color” and “Tint” are only supported in Video mode.
(#2) “Signal” is only supported in Analog VGA (RGB) signal.
(#3) For HDMI Source only.
(#4) For XGA model only.
(#5) For WXGA model only. 16:9 or 16:10 depend on “Screen Type” setting.
(#6) “3D Sync Invert” is only available when 3D is enabled and this mode
3D is for DLP link glass only.
(#7) The function depends on model’s specifications.
English
26
User Controls
IMAGE
Display Mode
There are many factory presets optimized for various types of
images.
Presentation: Good color and brightness from PC input.
Bright: Maximum brightness from PC input.
Movie: For home theater.
sRGB: Standardised accurate color.
Blackboard: This mode should be selected to achieve optimum
color settings when projecting onto a blackboard (green).
User: User’s settings.
3D: Recommend setting for 3D mode enabled. Any further ad-
justments by the user in 3D will be saved in this mode for further
use.
Brightness
Adjust the brightness of the image.
Press the
Press the
Contrast
to darken image.
to lighten the image.
The contrast controls the degree of difference between the lightest
and darkest parts of the picture.
Press the
Press the
to decrease the contrast.
to increase the contrast.
27
English
User Controls
Sharpness
Adjust the sharpness of the image.
Press the
Press the
Color
“Color” and “Tint”
functions are only
supported under
Video mode.
to decrease the sharpness.
to increase the sharpness.
Adjust a video image from black and white to fully saturated color.
Press the
Press the
Tint
to decrease the amount of saturation in the image.
to increase the amount of saturation in the image.
Adjust the color balance of red and green.
English
28
Press the
Press the
to increase the amount of green in the image.
to increase the amount of red in the image.
User Controls
IMAGE | Advanced
Gamma
This allows you to choose a degamma table that has been
fine-tuned to bring out the best image quality for the input.
Film: for home theater.
Video: for video or TV source.
Graphics: for image source.
Standard: for PC or computer source.
BrilliantColor™
This adjustable item utilizes a new color-processing algorithm and
system level enhancements to enable higher brightness while
providing true, more vibrant colors in picture. The range is from
“0” to “10”. If you prefer a stronger enhanced image, adjust toward
the maximum setting. For a smoother, more natural image, adjust
toward the minimum setting.
Color Temp
If set to cold temperature, the image looks more blue. (cold image)
If set to warm temperature, the image looks more red.
(warm image)
Color Settings
Press
into the next menu as below and then use
select item.
29
or
to
English
User Controls
Red/Green/Blue/Cyan/Magenta/Yellow: Use
White: Use
Reset: Choose “Yes” to return the factory default settings for
Hue, Saturation and Gain Colors.
or
or
to select
to select Red, Green and Blue Colors.
color adjustments.
Color Space
™™ (*) For models with
HDMI Input.
Select an appropriate color matrix type from AUTO, RGB,
RGB(0-255)(*), RGB(16-235)(*) or YUV.
Reset
Choose “Yes” to return the display parameters on all menus to the
factory default settings.
English
30
User Controls
IMAGE | Advanced
| Signal (RGB)
“Signal” is only
supported in Analog
VGA (RGB) signal.
Automatic
Automatically selects the signal. If you use this function, the
Phase, frequency items are grayed out, and if Signal is not automatic, the phase, frequency items will appear for user to manually
tune and saved in settings after that for next time projector turns
off and on again.
Phase
Synchronize the signal timing of the display with the graphic card.
If the image appears to be unstable or flickers, use this function to
correct it.
Frequency
Change the display data frequency to match the frequency of
your computer’s graphic card. Use this function only if the image
appears to flicker vertically.
H. Position
Press the
Press the
to move the image left.
to move the image right.
V. Position
Press the
Press the
to move the image down.
to move the image up.
31
English
User Controls
DISPLAY
Format
Use this function to choose your desired aspect ratio.
SVGA/XGA
4:3: This format is for 4×3 input sources.
16:9: This format is for 16×9 input sources, like HDTV and DVD
enhanced for Wide screen TV.
Native: This format displays the original image without any
scaling.
AUTO: Automatically selects the appropriate display format.
Auto
4:3
Wide
Laptop
SDTV
HDTV
English
32
Input resolution
Auto/Scale
(SVGA)
Auto/Scale
(XGA)
H
V
H
V
H
V
640
480
800
600
1024
768
800
600
800
600
1024
768
1024
768
800
600
1024
768
1280
1024
800
600
1024
768
1400
1050
800
600
1024
768
1600
1200
800
600
1024
768
1280
720
800
450
1024
576
1280
768
800
480
1024
614
1280
800
800
500
1024
640
720
576
800
450
1024
576
720
480
800
450
1024
576
1280
720
800
450
1024
576
1920
1080
800
450
1024
576
User Controls
Aspect ratio
(source detected)
Resize image (SVGA)
Resize image (XGA)
4:3
800 x 600 center
1024 x 768 center
16:9
800 x 450 center
1024 x 576 center
No resize image, 1:1 mapping and
centered. This format shows the
original image without scaling.
Native
WXGA
4:3: This format is for 4×3 input sources.
16:9: This format is for 16×9 input sources, like HDTV and DVD
16:9 or 16:10
depend on “Screen
Type” setting.
enhanced for Wide screen TV.
16:10: This format is for 16×10 input sources, like widescreen
laptops.
Native: This format displays the original image without any
scaling.
AUTO: Automatically selects the appropriate display format.
Auto
4:3
Wide
Laptop
SDTV
HDTV
Input resolution
Screen Type = 16:10
Screen Type = 16:9
Auto/Scale
Auto/Scale
H
V
H
V
H
V
640
480
1066
800
960
720
800
600
1066
800
960
720
1024
768
1066
800
960
720
1280
1024
1066
800
960
720
1400
1050
1066
800
960
720
1600
1200
1066
800
960
720
1280
720
1280
720
1280
720
1280
768
1280
768
1200
768
1280
800
1280
800
1152
800
720
576
1280
720
1280
720
720
480
1280
720
1280
720
1280
720
1280
720
1280
720
1920
1080
1280
720
1280
720
33
English
User Controls
16:10 Screen
480i/p
576i/p
1080i/p
720p
4:3
1066 x 800 center
16:10
1280 x 800 center
1:1 mapping
centered.
Native
16:9 Screen
480i/p
576i/p
1:1 mapping (960 x
540) display
1280 x 800
1280 x 720
center
1:1
mapping
centered.
1080i/p
720p
PC
4:3
960 x 720 center
16:9
1280 x 720 center
Native
1:1 mapping
centered.
PC
1:1 mapping (960 x
540) display
1280 x 720
1280 x 720
center
1:1
mapping
centered.
Edge Mask
Each I/O has
different setting of
“Edge Mask”.
Edge mask function removes the noise in a video image. Edge
mask the image to remove video encoding noise on the edge of
video source.
Zoom
“Edge Mask” and
“Zoom” can’t work at
same time.
Press the to reduce the size of an image.
Press the to magnify an image on the projection screen.
Image Shift
Press
into the next menu as below and then use
select item.
H: Use or
V: Use or
V Keystone
or
to
to shift the projected image position horizontally.
to Shift the projected image position vertically.
Press the or to adjust image distortion vertically. If the image
looks trapezoidal, this option can help make the image rectangular.
English
34
User Controls
DISPLAY | 3D
3D Mode
“3D Sync Invert” is
only available when
3D is enabled and
this mode 3D is for
DLP link glass only.
Compatible 3D
source, 3D content
and active shutter
glasses are required
for 3D viewing.
See page 55 for
supported 3D
formats.
Off: Select “Off” to turn 3D settings off for 3D images.
DLP Link: Select “DLP Link” to use optimized settings for DLP
Link 3D images.
3D -> 2D
3D: Display 3D signal.
L (Left): Display the left frame of 3D content.
R (Right): Display the right frame of 3D content.
3D Format
Auto : When a 3D identification signal is detected, the 3D
format is selected automatically.
SBS: Use this mode for “Side-by-side” format 3D content.
Top and Bottom: Use this mode for “Top and Bottom” format 3D
content.
Frame Sequential: Use this mode for “Frame Sequential”
format 3D content.
3D Sync. Invert
Press the “On” to invert left and right frame contents.
Press the “Off” for default frame contents.
35
English
User Controls
SETUP
Language
Choose the multilingual OSD menu. Press or into the sub
menu and then use the
or
key to select your preferred
language. Press “Enter” to finalize the selection.
Projection
Rear-Desktop and
Rear-Ceiling are
to be used with a
translucent screen.

Front-Desktop
This is the default selection. The image is projected straight on
the screen.

Rear-Desktop
When selected, the image will appear reversed.

Front-Ceiling
When selected, the image will turn upside down.

Rear-Ceiling
When selected, the image will appear reversed in upside down
position.
English
36
User Controls
Menu Location
Choose the menu location on the display screen.
Screen Type
“Screen Type” is for
WXGA only.
Choose the screen type from16:10 or 16:9.
Projector ID
ID definition can be set up by menu (range 0-99), and allow user
control an individual projector by RS232. Refer to pages 56-60. for
the complete list of RS232 commands.
37
English
User Controls
SETUP |
Audio Settings
Internal Speaker
Choose the “On” or “Off” to turn on or off the internal speaker.
Mute
Choose the “On” to turn mute on.
Choose the “Off” to turn mute off.
Volume
Press the to decrease the volume.
Press the to increase the volume.
Audio Input
The default audio inputs are on the back panel of the projector.
Use this option to reassign any of the Audio Inputs to the current
image source.
Default: VGA1/VGA2.
Audio1: Video/S-Video.
Audio2: HDMI.
English
38
User Controls
SETUP | Advanced
Logo
Press
to capture an image of the picture currently displayed
on screen. If changes are made they will take effect the next time
the projector is powered on.
Default: The default startup screen.
Neutral: Logo is not displayed on startup screen.
Closed Captioning
Use this function to set the desired startup screen. If changes are
made they will take effect the next time the projector is powered
on.
Off: select “Off” to turn off the closed captioning feature.
CC1:CC1 language: American English.
CC2:CC2 language (depending on the TV channel of the
user):Spanish, French, Portuguese, German, Danish.
39
English
User Controls
OPTIONS
Input Source
Use this option to enable / disable input sources. Press
to enter
the sub menu and select which sources you require. Press “Enter”
to finalize the selection. The projector will not search for inputs that
are not selected.
Source Lock
On: The projector will only search current input connection.
Off: The projector will search for other signals if the current
input signal is lost.
High Altitude
When “On” is selected, the fans will spin faster. This feature is
useful in high altitude areas where the air is thin.
Information Hide

To turn off the keypad lock, press and
hold “Enter” key on
top of the projector
for 5 seconds.
On: Choose “On” to hide the info message.
Off: Choose “Off” to show the “searching” message.
Keypad Lock
When the keypad lock function is “On”, the control panel will be
locked however, the projector can be operated by the remote control. By selecting “Off”, you will be able to reuse the control panel.
Test Pattern
Display a test pattern. There are Grid, White pattern and None.
English
40
User Controls
IR Function(*)
On: Choose “On”, the projector can be operated by the remote
(*) The function depends on model’s
specifications.
control. When you change the setting from “Off” to “On”, it will
display a warning message:
Off: Choose “Off”, you will only be able to use the control panel
keys. When you change the setting from “On” to “Off”, it will
display a warning message:
Background Color
Use this feature to display a “Black”, “Red”, “Blue”, “Green” or
“White”, screen when no signal is available.
Reset
Choose “Yes” to return the display parameters on all menus to the
factory default settings.
41
English
User Controls
OPTIONS |
Advanced
Direct Power On
Choose “On” to activate Direct Power mode. The projector will
automatically power on when AC power is supplied, without
pressing the “ ” key on the projector control panel or on the
remote control.
Auto Power Off (min)

When Power mode
(Standby) is set to Eco (<0.5W), the
VGA output and
Audio pass-through
will be deactivated
when the projector is
in standby.

The value of sleep
timer will be reset to
zero after the projector power off.
Sets the countdown timer interval. The countdown timer will start,
when there is no signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Sleep Timer (min)
Sets the countdown timer interval. The countdown timer will start,
with or without a signal being sent to the projector. The projector
will automatically power off when the countdown has finished (in
minutes).
Quick Resume
On: If the projector is accidentally turned off, this feature allows
the projector to be instantly powered on again, if selected
within a period of 100 seconds.
Off: The fan will start cooling the system immediately when user
turns off the projector.
Power Mode (Standby)
Eco.: Choose “Eco.” to save power dissipation further < 0.5W.
Active: Choose “Active” to return to normal standby and the
VGA out port will be enabled.
English
42
User Controls
OPTIONS |
Lamp Settings
Lamp Hours
Display the projection time.
Lamp Reminder
Choose this function to show or to hide the warning message
when the changing lamp message is displayed.
The message will appear 30 hours before suggested replacement
of lamp.
Brightness Mode

When ambient temperature is over 40°C
in operating, the
projector will switch
to Eco automatically.
BRIGHT: Choose “BRIGHT” to increase the brightness.
Eco.: Choose “Eco.” to dim the projector lamp which will lower
power consumption and extend the lamp life.
`` Dynamic: Choose “Dynamic” to dim the lamp power which
will be based on brightness level of the content and
adjust lamp power consumption between 100% and
30% dynamically. The lamp life will be extended.
Lamp Reset
Reset the lamp hour counter after replacing the lamp.
43
English
User Controls
OPTIONS |
Optional Filter
Settings
Optional Filter Installed
Select “Yes” to display warning message after 500 hours of use.
Select “No” to turn off warning message.
The default setting for Filter is “No”. After assembling filter, please
turn on the projector then press “Menu”, go to “OPTIONS -> Optional Filter Settings -> Optional Filter Installed” and select “Yes”.
Filter Usage Hours
Display the filter time.
Filter Reminder
Choose this function to show or hide the warning massage when
the changing filter message is displayed. (Factory default setting:
500 hours)
Filter Reset
Reset the dust filter counter after replacing or cleaning the dust
filter.
English
44
Appendices
Troubleshooting
If you experience a problem with your projector,
please refer to the following information. If a
problem persists, please contact your local
reseller or service center.
No image appears on-screen
Ensure all the cables and power connections are correctly and
securely connected as described in the “Installation” section.
Ensure all the pins of connectors are not bent or broken.
Check if the projection lamp has been securely installed. Please
refer to the “Replacing the lamp” section.
Make sure you have removed the lens cap and the projector is
switched on.
Ensure that the “AV Mute” feature is not turned on.
Partial, scrolling or incorrectly displayed image
 Press “Re-SYNC” on the remote control or control panel.
If you are using a PC:
For Windows 95, 98, 2000, XP, Windows 7:
1. Open the “My Computer” icon, the “Control Panel” folder, and
then double click on the “Display” icon.
2. Select the “Settings” tab.
3. Verify that your display resolution setting is lower than or equal
to UXGA (1600 × 1200).
4. Click on the “Advanced Properties” button.
If the projector is still not projecting the whole image, you will also
need to change the monitor display you are using. Refer to the
following steps.
5. Verify the resolution setting is lower than or equal to UXGA
(1600 × 1200).
6. Select the “Change” button under the “Monitor” tab.
45
English
Appendices
7. Click on “Show all devices”. Next, select “Standard monitor
types” under the SP box; choose the resolution mode you need
under the “Models” box.
8. Verify that the resolution setting of the monitor display is lower
than or equal to UXGA (1600 × 1200).
If you are using a Notebook:
1. First, follow the steps above to adjust resolution of the
computer.
2. Press the appropriate keys listed below for your notebook
manufacturer to send signal out from notebook to projector.
Example: [Fn]+[F4]
Acer  [Fn]+[F5]
Asus  [Fn]+[F8]
Dell  [Fn]+[F8]
Gateway  [Fn]+[F4]
IBM/Lenovo 
HP/Compaq 
NEC 
Toshiba 
[Fn]+[F7]
[Fn]+[F4]
[Fn]+[F3]
[Fn]+[F5]
Mac Apple:
System Preference  Display  Arrangement  Mirror
display
If you experience difficulty changing resolutions or your monitor
freezes, restart all equipment including the projector.
The screen of the Notebook or PowerBook computer is not
displaying your presentation
If you are using a Notebook PC
Some Notebook PCs may deactivate their own screens when a
second display device is in use. Each has a different way to be
reactivated. Refer to your computer’s manual for detailed
information.
Image is unstable or flickering
Use “Phase” to correct it. See page 31 for more information.
Change the monitor color setting on your computer.
Image has vertical flickering bar
Use “Frequency” to make an adjustment. See page 31 for more
information.
Check
and re-configure the display mode of your graphic card to

make it compatible with the projector.
English
46
Appendices
Image is out of focus
Make sure the Lens cap is removed.
Adjust the Focus Ring on the projector lens.
Make sure the projection screen is between the required distance.
See pages 16-17.
The image is stretched when displaying 16:9 DVD title
When you play anamorphic DVD or 16:9 DVD, the projector will
show the best image when the projector display mode is set to
16:9 in the OSD.
If you play 4:3 format DVD titles, please change the format to 4:3
in the projector OSD.
If the image is still stretched, you will also need to adjust the
aspect ratio by referring to the following:
 Please setup the display format as 16:9 (wide) aspect ratio type
on your DVD player.
Image is too small or too large
Adjust the Zoom Ring on the top of the projector.
Move the projector closer to or further from the screen.
Press “Menu” button on the remote control, go to “Display 
Format” and try the different settings.
Use of Keystone
is not recommended.
Image has slanted sides
If possible, reposition the projector so that it is horizontally
centered on the screen and below the bottom of the screen.
Press
“Keystone +/-” button on the remote control until the sides

are vertical.
Use “Display  V Keystone” from the OSD to make an adjustment.
Image is reversed
Select “SETUP  Projection” from the OSD and adjust the
projection direction.
47
English
Appendices
The projector stops responding to all controls
If possible, turn off the projector, then unplug the power cord and
wait at least 60 seconds before reconnecting power.
Check
that “Keypad Lock” is not activated by trying to control the

projector with the remote control.
Blurry double image
Press “3D Format” button and switch to “Off” to avoid normal 2D
image is blurry double image.
Two images, side-by-side format
Press “3D Format” button and switch to “SBS” for input signal is
HDMI 1.3 2D 1080i side-by-side.
Image does not display in 3D
Check if the battery of 3D glasses is drained.
Check if the 3D glasses is turned on.
When the input signal is HDMI 1.3 2D (1080i side-by-side half),
press “3D Format” button and switch to “SBS”.
Lamp burns out or makes a popping sound
When the lamp reaches its end of life, it will burn out and may
make a loud popping sound. If this happens, the projector will not
turn on until the lamp module has been replaced. To replace the
lamp, follow the procedures in the “Replacing the Lamp” section on
pages 51-52.
English
48
Appendices
LED lighting message
Message
Standby State
(Input power cord)
Power on (Warming)
Lamp lighting
Steady light 
No light 
ON/STANDBY
LED
Temp-LED
Lamp-LED
(Green/Amber)
(Red)
(Red)
Amber
Flashing
Green
Green
Power off (Cooling)
Flashing
Green
Error (Over Temp.)
Flashing
Amber
Error (Fan fail)
Flashing
Amber
Error (Lamp fail)
Flashing
Amber
Flashing
49
English
Appendices
On Screen Messages
Temperature warning:
Fan failed:
Lamp warning:
Out of display range:
If the remote control does not work
Check the operating angle of the remote control is within ±20°
both horizontally and vertically of one of the IR receivers on the
projector.
Make sure there are not any obstructions between the remote
control and the projector. Move to within 7 m (±0°) of the projector.
 Make sure the batteries are inserted correctly.
 Replace batteries if they are exhausted.
English
50
Appendices
Replacing the Lamp
The projector automatically detects the lamp life. When the
lamp life is nearing the end of use, you will receive a warning
message.
When you see this message, please contact your local reseller
or service center to change the lamp as soon as possible.
Make sure the projector has been cooled down for at least 30
minutes before changing the lamp.
Warning: If ceiling mounted, please use caution when
opening the lamp access panel. It is recommended to wear
safety glasses if changing the bulb when ceiling mounted.
“Caution must be used to prevent any loose parts from falling out of projector.”
Warning: Lamp compartment may be hot! Allow it to cool
down before changing the lamp!
Warning: To reduce the risk of personal injury, do not drop
the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
51
English
Appendices
2
The screws on the
lamp cover and the
lamp cannot be
removed.
5
The projector
cannot be turned
on if the lamp
cover has not been
placed back on the
projector.
Do not touch the
glass area of the
lamp. Hand oil can
cause the lamp to
shatter. Use a dry
cloth to clean the
lamp module if it
was accidentally
touched.
6
3
4
1
7
Lamp Replacement Procedure:
1.Switch off the power to the projector by pressing the “ ” button.
2.Allow the projector to cool down for at least 30 minutes.
3.Disconnect the power cord.
4.Unscrew the one screw on the cover. 1
5.Lift up and remove the cover. 2
6.Lift up the lamp handle. 3
7.Press on the both sides then lift up and remove the lamp cord. 4
8.Unscrew the one screw on the lamp module. 5
9.Lift up the lamp handle 6 and remove the lamp module slowly and carefully.
7
To replace the lamp module, reverse the previous steps.
10. Turn on the projector and reset the lamp timer.
Lamp Reset: (i) Press “Menu”  (ii) Select “OPTIONS”  (iii) Select
“Lamp Settings”  (iv) Select “Lamp Reset”  (v) Select “Yes”.
English
52
Appendices
Installing and Cleaning the Dust
Filter
Installing the Dust Filter
Procedure:
Dust filters are
only required/supplied in selected
regions with excessive dust.
1. Install two filters.
2. Turn on the projector then press “Menu”, go to “OPTIONS -> Optional Filter Settings -> Optional Filter Installed” and select “Yes”.
1
Cleaning the Dust Filter
We recommends cleaning the dust filter every three
months; clean it more often if the projector is used in a
dusty environment.
Procedure:
1.
2.
3.
4.
5.
6.
Switch off the power to the projector by pressing the “ ” button.
Disconnect the power cord.
Remove the dust filter slowly and carefully.
Clean or replace the dust filter.
To install the dust filter, reverse the previous steps.
Reset the dust filter counter after replacing or cleaning the dust
filter. Press “Menu”, go to “OPTIONS -> Optional Filter Settings ->
Filter Reset”
Turn on the projector, then press “Menu”, “OPTIONS -> Optional
Filter Settings -> Optional Filter Installed” and select “No” when
you pull out the dust filter and would not install it again.
1
2
53
English
Appendices
Compatibility Modes
 Computer/Video/HDMI/Mac Compatibility
™™ For widescreen
resolution (WXGA),
the compatibility
support is dependent on Notebook/
PC models.
™™ Please note that using resolutions other
than native 800 x
600 (SVGA model),
1024 x 768 (XGA
model), 1280 x 800
(WXGA model) may
result in some loss
of image clarity.
™™ (*1) 1920 x1200
@60Hz only support
RB (reduced blanking).
™™ (*2) 3D timing for
True 3D projector.
™™ (*3) is not supported
HDMI input signal
for Mac.
™™ (*4) Proscene and
Data Projector >
4,000 Lumens only,
Native resolution
must support.
™™ (*5) Window 8
standard timing.
™™ 120Hz input signals
may be dependent
on graphics cards
support.
Signal
Resolution
Refresh Rate
(Hz)
Video
Analog
HDMI
Mac
NTSC
720 x 480
60
O
-
-
-
PAL/SECAM
720 x 576
50
O
-
-
-
640 x 480
60
-
O
O
O
640 x 480
67
-
O
-
-
640 x 480
72.8
-
O
-
O
640 x 480
85
-
O
-
O
800 x 600
56.3
-
O
-
-
800 x 600
60.3 (*2)
-
O
O
O
800 x 600
72.2
-
O
O
O
800 x 600
85.1
-
O
O
O
800 x 600
120 (*2)
-
O
O
-
1024 x 768
48
-
O
O
1024 x 768
50
-
O (*4)
O (*4)
VGA
SVGA
XGA
WSVGA
HDTV (720p)
WXGA
SXGA
SXGA+
English
54
1024 x 768
60
-
O
O
O
1024 x 768
70.1
-
O
O
O
1024 x 768
75
-
O
O
O
1024 x 768
85
-
O
O
O
1024 x 768
120 (*2)
-
O
O
-
1024 x 600
60
-
-
O
-
1280 x 720
50
O
O
O
-
1280 x 720
60 (*2)
O
O
O
O
1280 x 720
120 (*2)
-
O
O
-
1280 x 768
60
-
O
O
O (*3)
1280 x 768
75
-
O
O
O
1280 x 768
85
-
O
O
O (*3)
1280 x 800
48
-
O
O (*4)
1280 x 800
50
-
1280 x 800
60
-
O
O
1366 x 768
60 (*5)
-
O
O
-
1280 x 1024
60
-
O
O
O
1280 x 1024
75
-
O
O
O
1280 x 1024
85
-
O
O
-
1400 x 1050
60
-
O
O
-
(*2)
O
(*4)
O
O
Appendices
Signal
UXGA
HDTV (1080p)
HDTV (1080i)
WUXGA (*1)
Resolution
Refresh Rate
(Hz)
Video
Analog
HDMI
Mac
1600 x1200
60
-
O
O
-
1920 x 1080
24
O
O
O
-
1920 x 1080
30
-
-
O
-
1920 x 1080
50
O
O
O
-
1920 x 1080
60
O
O
O
O
1920 x 1080
50
O
-
O
-
1920 x 1080
60
O
-
O
-
1920 x 1200
50
-
O (*4)
O (*4)
-
1920 x 1200
60
-
O
O
O
SDTV (576i)
720 x 576
50
O
-
O
-
SDTV (576p)
720 x 576
50
O
-
O
-
SDTV (480i)
720 x 480
60
O
-
O
-
SDTV (480p)
720 x 480
60
O
-
O
-
 3D Input Video Compatibility
Input Timing
HDMI 1.4a 3D
Input
Input
Resolution
1280 x 720p @ 50Hz
Top-and-Bottom
1280 x 720p @ 60Hz
Top-and-Bottom
1280 x 720p @ 50Hz
Frame packing
1280 x 720p @ 60Hz
Frame packing
1920 x 1080i @ 50 Hz
Side-by-Side (Half)
1920 x 1080i @ 60 Hz
Side-by-Side (Half)
1920 x 1080p @ 24 Hz
Top-and-Bottom
1920 x 1080p @ 24 Hz
Frame packing
1920 x 1080i @ 50Hz
1920 x 1080i @ 60Hz
1280 x 720p @ 50Hz
Side-by-Side (Half)
While 3D Format is
“SBS”
Top-and-Bottom
While 3D Format is
“Top and Bottom”
HQFS
While 3D Format is
“Frame sequential”
1280 x 720p @ 60Hz
HDMI 1.3 3D
Content
1920 x 1080i @ 50Hz
1920 x 1080i @ 60Hz
1280 x 720p @ 50Hz
1280 x 720p @ 60Hz
480i
55
English
Appendices
RS232 Commands and Protocol
Function List
RS232 Pin Assignments
9
5
Pin no.
English
56
8
4
7
3
6
2
1
Spec.
(from projector side)
1
N/A
2
RXD
3
TXD
4
N/A
5
GND
6
N/A
7
N/A
8
N/A
9
N/A
Appendices
RS232 Protocol Function List
XX=00-99, projector's ID,
Baud Rate : 9600
XX=00 is for all projectors
Data Bits: 8
1. There is a <CR> after Parity: None
Optoma
Command Table.
all ASCIIV1
commands.
Stop Bits: 1
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------Baud Rate : 9600
Note : There is a <CR> after all ASCII commands
Flow Control : None
8
0D is the HEX code for <CR> in ASCII code
2. Data
0DBits:
is the
HEX code
Parity: None
UART16550 FIFO: Disable
Stop
1
for Bits:
<CR>
in ASCII
Flow Control : None
Projector Return (Pass): P
code. FIFO: Disable
UART16550
Projector Return (Pass): P
Projector Return (Fail): F
Projector Return (Fail): F
XX=01ˀ99, projector's ID, XX=00 is for all projectors
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to projector
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX00 1
7E 30 30 30 30 20 31 0D
Power ON
~XX00 0
7E 30 30 30 30 20 30 0D
Power OFF
(0/2 for backward compatible)
~XX00 1 ~nnnn
7E 30 30 30 30 20 31 20 a 0D Power ON with Password
~nnnn = ~0000 (a=7E 30 30 30 30) ~9999 (a=7E 39 39 39 39)
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ---------------------------------~XX01 1
7E 30 30 30 31 20 31 0D
Resync
~XX02 1
7E 30 30 30 32 20 31 0D
AV Mute
On
~XX02 0
7E 30 30 30 32 20 30 0D
Off (0/2 for backward compatible)
~XX03 1
7E 30 30 30 33 20 31 0D
Mute
On
~XX03 0
7E 30 30 30 33 20 30 0D
Off (0/2 for backward compatible)
~XX04 1
7E 30 30 30 34 20 31 0D
Freeze
~XX04 0
7E 30 30 30 34 20 30 0D
Unfreeze
(0/2 for backward compatible)
~XX05 1
7E 30 30 30 35 20 31 0D
Zoom Plus
~XX06 1
7E 30 30 30 36 20 31 0D
Zoom Minus
~XX12 1
7E 30 30 31 32 20 31 0D
Direct Source Commands
HDMI
~XX12 5
7E 30 30 31 32 20 35 0D
VGA1
~XX12 6
7E 30 30 31 32 20 36 0D
VGA 2
~XX12 8
7E 30 30 31 32 20 38 0D
VGA1 Component
~XX12 9
7E 30 30 31 32 20 39 0D
S-Video
~XX12 10
7E 30 30 31 32 20 31 30 0D
Video
~XX12 13
7E 30 30 31 32 20 31 33 0D
VGA 2 Component
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ---------------------------------~XX20 1
7E 30 30 32 30 20 31 0D
Display Mode
Presentation
~XX20 2
7E 30 30 32 30 20 32 0D
Bright
~XX20 3
7E 30 30 32 30 20 33 0D
Movie
~XX20 4
7E 30 30 32 30 20 34 0D
sRGB
~XX20 5
7E 30 30 32 30 20 35 0D
User
~XX20 7
7E 30 30 32 30 20 37 0D
Blackboard
~XX20 9
7E 30 30 32 30 20 39 0D
3D
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ---------------------------------~XX21 n
7E 30 30 32 31 20 a 0D
Brightness
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX22 n
7E 30 30 32 32 20 a 0D
Contrast
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX23 n
7E 30 30 32 33 20 a 0D
Sharpness
n = 1 (a=31) ~ 15 (a=31 35)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX24 n
7E 30 30 32 34 20 a 0D
Color Settings/White
Red
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX25 n
7E 30 30 32 35 20 a 0D
Green
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX26 n
7E 30 30 32 36 20 a 0D
Blue
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX33 1
7E 30 30 33 33 20 31 0D
Reset
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ---------------------------------n = 1 (a=30) ~ 10 (a=31 30)
~XX34 n
7E 30 30 33 34 20 a 0D
BrilliantColorTM
~XX35 1
7E 30 30 33 35 20 31 0D
Gamma
Film
~XX35 2
7E 30 30 33 35 20 32 0D
Video
~XX35 3
7E 30 30 33 35 20 33 0D
Graphics
~XX35 4
7E 30 30 33 35 20 34 0D
Standard
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ---------------------------------~XX36 1
7E 30 30 33 36 20 31 0D
Color Temp.
Warm
~XX36 2
7E 30 30 33 36 20 32 0D
Medium
~XX36 3
7E 30 30 33 36 20 33 0D
Cold
~XX37 1
7E 30 30 33 37 20 31 0D
Color Space
Auto
~XX37 2
7E 30 30 33 37 20 32 0D
RGB\RGB(0-255)
~XX37 3
7E 30 30 33 37 20 33 0D
YUV
~XX37 4
7E 30 30 33 37 20 34 0D
RGB(16-235)
~XX73 n
7E 30 30 37 33 20 a 0D
Signal
Frequency
n = -5 (a=2D 35) ~ 5 (a=35) By signal
~XX91 n
7E 30 30 39 31 20 a 0D
Automatic
n = 0 disable; n = 1 enable
~XX74 n
7E 30 30 37 34 20 a 0D
Phase
n = 0 (a=30) ~ 31 (a=33 31) By signal
~XX75 n
7E 30 30 37 35 20 a 0D
H. Position
n = -5 (a=2D 35) ~ 5 (a=35) By timing
~XX76 n
7E 30 30 37 36 20 a 0D
V. Position
n = -5 (a=2D 35) ~ 5 (a=35) By timing
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- ----------------------------------
57
English
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX45 n
7E 30 30 34 34 20 a 0D
Color (Saturation)
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
~XX44 n
7E 30 30 34 35 20 a 0D
Tint
n = -50 (a=2D 35 30) ~ 50 (a=35 30)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX60 1
7E 30 30 36 30 20 31 0D
Format
4:3
~XX60 2
7E 30 30 36 30 20 32 0D
16:9
~XX60 3
7E 30 30 36 30 20 33 0D
16:10(WXGA)
~XX60 6
7E 30 30 36 30 20 36 0D
Native
~XX60 7
7E 30 30 36 30 20 37 0D
Auto
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX61 n
7E 30 30 36 31 20 a 0D
Edge mask
n = 0 (a=30) ~ 10 (a=31 30)
~XX62 n
7E 30 30 36 32 20 a 0D
Zoom
n = -5 (a=2D 35) ~ 25 (a=32 35)
~XX63 n
7E 30 30 36 33 20 a 0D
H Image Shift
n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30)
~XX64 n
7E 30 30 36 34 20 a 0D
V Image Shift
n = -100 (a=2D 31 30 30) ~ 100 (a=31 30 30)
~XX66 n
7E 30 30 36 36 20 a 0D
V Keystone
n = -40 (a=2D 34 30) ~ 40 (a=34 30)
~XX230 0
7E 30 30 32 33 30 20 30 0D
3D Mode
OFF
~XX230 1
7E 30 30 32 33 30 20 31 0D
3D Mode
DLP-Link
~XX400 0
7E 30 30 34 30 30 20 30 0D
3DШ2D
3D
~XX400 1
7E 30 30 34 30 30 20 31 0D
L
~XX400 2
7E 30 30 34 30 30 20 32 0D
R
~XX405 0
7E 30 30 34 30 35 20 30 0D
3D Format
Auto
~XX405 1
7E 30 30 34 30 35 20 31 0D
SBS
~XX405 2
7E 30 30 34 30 35 20 32 0D
Top and Bottom
~XX405 3
7E 30 30 34 30 35 20 33 0D
Frame sequential
~XX231 0
7E 30 30 32 33 31 20 30 0D
3D Sync Invert
On
~XX231 1
7E 30 30 32 33 31 20 31 0D
3D Sync Invert
Off
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX70 1
7E 30 30 37 30 20 31 0D
Language
English
~XX70 2
7E 30 30 37 30 20 32 0D
German
~XX70 3
7E 30 30 37 30 20 33 0D
French
~XX70 4
7E 30 30 37 30 20 34 0D
Italian
~XX70 5
7E 30 30 37 30 20 35 0D
Spanish
~XX70 6
7E 30 30 37 30 20 36 0D
Portuguese
~XX70 7
7E 30 30 37 30 20 37 0D
Polish
~XX70 8
7E 30 30 37 30 20 38 0D
Dutch
~XX70 9
7E 30 30 37 30 20 39 0D
Swedish
~XX70 10
7E 30 30 37 30 20 31 30 0D
Norwegian/Danish
~XX70 11
7E 30 30 37 30 20 31 31 0D
Finnish
~XX70 12
7E 30 30 37 30 20 31 32 0D
Greek
~XX70 13
7E 30 30 37 30 20 31 33 0D
Traditional Chinese
~XX70 14
7E 30 30 37 30 20 31 34 0D
Simplified Chinese
~XX70 15
7E 30 30 37 30 20 31 35 0D
Japanese
~XX70 16
7E 30 30 37 30 20 31 36 0D
Korean
~XX70 17
7E 30 30 37 30 20 31 37 0D
Russian
~XX70 18
7E 30 30 37 30 20 31 38 0D
Hungarian
~XX70 19
7E 30 30 37 30 20 31 39 0D
Czechoslovak
~XX70 20
7E 30 30 37 30 20 32 30 0D
Arabic
~XX70 21
7E 30 30 37 30 20 32 31 0D
Thai
~XX70 22
7E 30 30 37 30 20 32 32 0D
Turkish
~XX70 23
7E 30 30 37 30 20 32 33 0D
Farsi
~XX70 25
7E 30 30 37 30 20 32 33 0D
Vietnamese
~XX70 26
7E 30 30 37 30 20 32 33 0D
Indonesian
~XX70 27
7E 30 30 37 30 20 32 33 0D
Romanian
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX71 1
7E 30 30 37 31 20 31 0D
Projection
Front-Desktop
~XX71 2
7E 30 30 37 31 20 32 0D
Rear-Desktop
~XX71 3
7E 30 30 37 31 20 33 0D
Front-Ceiling
~XX71 4
7E 30 30 37 31 20 34 0D
Rear-Ceiling
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX72 1
7E 30 30 37 32 20 31 0D
Menu Location
Top Left
~XX72 2
7E 30 30 37 32 20 32 0D
Top Right
~XX72 3
7E 30 30 37 32 20 33 0D
Centre
~XX72 4
7E 30 30 37 32 20 34 0D
Bottom Left
~XX72 5
7E 30 30 37 32 20 35 0D
Bottom Right
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------(WXGA only)
~XX90 1
7E 30 30 39 31 20 31 0D
Screen Type
16:10
~XX90 0
7E 30 30 39 31 20 30 0D
16:9
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX77 n
7E 30 30 37 37 20 aabbcc 0D Security
Security Timer
Month/Day/Hour
n = mm/dd/hh
mm= 00 (aa=30 30) ~ 12 (aa=31 32)
dd = 00 (bb=30 30) ~ 30 (bb=33 30)
hh= 00 (cc=30 30) ~ 24 (cc=32 34)
~XX78 1
7E 30 30 37 38 20 31 0D
Security Settings
Enable
~XX78 0 ~nnnn
7E 30 30 37 38 20 32 20 a 0D
Disable(0/2 for backward compatible)
~nnnn = ~0000 (a=7E 30 30 30 30) ~9999 (a=7E 39 39 39 39)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX79 n
7E 30 30 37 39 20 a 0D
Projector ID
n = 00 (a=30 30) ~ 99 (a=39 39)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX80 1
7E 30 30 38 30 20 31 0D
Mute
On
~XX80 0
7E 30 30 38 30 20 30 0D
Off (0/2 for backward compatible)
~XX310 0
7E 30 33 31 30 20 30 0D
Internal Speaker
Off
~XX310 1
7E 30 33 31 30 20 31 0D
On
~XX81 n
7E 30 30 38 31 20 a 0D
Volume (Audio)
n = 0 (a=30) ~ 10 (a=31 30)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX82 1
7E 30 30 38 32 20 31 0D
Logo
Default
~XX82 3
7E 30 30 38 32 20 33 0D
Neutral
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
English
58
2
Appendices
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX88 0
7E 30 30 38 38 20 30 0D
Closed Captioning
Off
~XX88 1
7E 30 30 38 38 20 31 0D
cc1
~XX88 2
7E 30 30 38 38 20 32 0D
cc2
~XX89 0
7E 30 30 38 39 20 30 0D
Audio Input
Default
~XX89 1
7E 30 30 38 39 20 31 0D
Audio1
~XX89 3
7E 30 30 38 39 20 33 0D
Audio2(SVGA2, SVGA3, XGA1, XGA2, WXGA)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX100 1
7E 30 30 31 30 30 20 31 0D
Source Lock
On
~XX100 0
7E 30 30 31 30 30 20 30 0D
Off (0/2 for backward compatible)
~XX101 1
7E 30 30 31 30 31 20 31 0D
High Altitude
On
~XX101 0
7E 30 30 31 30 31 20 30 0D
Off (0/2 for backward compatible)
~XX102 1
7E 30 30 31 30 32 20 31 0D
Information Hide
On
~XX102 0
7E 30 30 31 30 32 20 30 0D
Off (0/2 for backward compatible)
~XX103 1
7E 30 30 31 30 33 20 31 0D
Keypad Lock
On
~XX103 0
7E 30 30 31 30 33 20 30 0D
Off (0/2 for backward compatible)
~XX195 0
7E 30 30 31 39 35 20 30 0D
Test Pattern
None
~XX195 1
7E 30 30 31 39 35 20 31 0D
Grid
~XX195 2
7E 30 30 31 39 35 20 32 0D
White Pattern
~XX11 0
7E 30 30 31 31 20 30 0D
IR Function
Off
~XX11 1
7E 30 30 31 31 20 31 0D
On
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX104 1
7E 30 30 31 30 34 20 31 0D
Background Color
Blue
~XX104 2
7E 30 30 31 30 34 20 32 0D
Black
~XX104 3
7E 30 30 31 30 34 20 33 0D
Red
~XX104 4
7E 30 30 31 30 34 20 34 0D
Green
~XX104 5
7E 30 30 31 30 34 20 35 0D
White
~XX105 1
7E 30 30 31 30 35 20 31 0D
Advanced
Direct Power On
On
~XX105 0
7E 30 30 31 30 35 20 30 0D
Off (0/2 for backward compatible)
~XX106 n
7E 30 30 31 30 36 20 a 0D
Auto Power Off (min) n = 0 (a=30) ~ 180 (a=31 38 30)
~XX107 n
7E 30 30 31 30 37 20 a 0D
Sleep Timer (min)
n = 0 (a=30) ~ 990 (a=39 39 39)
~XX115 1
7E 30 30 31 31 35 20 31 0D
Quick Resume
On
~XX115 0
7E 30 30 31 31 35 20 30 0D
Off (0/2 for backward compatible)
~XX114 1
7E 30 30 31 31 34 20 31 0D
Power Mode(Standby) Eco.(<=0.5W)
~XX114 0
7E 30 30 31 31 34 20 30 0D
Active (0/2 for backward compatible)
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX109 1
7E 30 30 31 30 39 20 31 0D
Lamp Reminder
On
~XX109 0
7E 30 30 31 30 39 20 30 0D
Off (0/2 for backward compatible)
~XX110 1
7E 30 30 31 31 30 20 31 0D
Brightness Mode
Bright
~XX110 2
7E 30 30 31 31 30 20 32 0D
Eco
~XX110 4
7E 30 30 31 31 30 20 34 0D
Dynamic
~XX111 1
7E 30 30 31 31 31 20 31 0D
Lamp Reset
Yes
~XX111 0
7E 30 30 31 31 31 20 30 0D
No (0/2 for backward compatible)
~XX322 0
7E 30 30 33 32 32 20 30 0D
Filter Reminder
Off
~XX322 1
7E 30 30 33 32 32 20 31 0D
300 hr
~XX322 2
7E 30 30 33 32 32 20 32 0D
500 hr
~XX322 3
7E 30 30 33 32 32 20 33 0D
800 hr
~XX322 4
7E 30 30 33 32 32 20 34 0D
1000 hr
~XX323 1
7E 30 30 33 32 33 20 31 0D
Filter Reset
Yes
~XX323 0
7E 30 30 33 32 33 20 30 0D
No
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX112 1
7E 30 30 31 31 32 20 31 0D
Reset
Yes
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX99 1
7E 30 30 39 39 20 31 0D
RS232 Alert Reset
Reset System Alert
~XX210 n
7E 30 30 32 30 30 20 n 0D
Display message on the OSD
n: 1-30 characters
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND to emulate Remote
-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX140 10
7E 30 30 31 34 30 20 31 30 0D
Up
~XX140 11
7E 30 30 31 34 30 20 31 31 0D
Left
~XX140 12
7E 30 30 31 34 30 20 31 32 0D
Enter (for projection MENU)
~XX140 13
7E 30 30 31 34 30 20 31 33 0D
Right
~XX140 14
7E 30 30 31 34 30 20 31 34 0D
Down
~XX140 15
7E 30 30 31 34 30 20 31 35 0D
Keystone +
~XX140 16
7E 30 30 31 34 30 20 31 36 0D
Keystone –
~XX140 17
7E 30 30 31 34 30 20 31 37 0D
Volume –
~XX140 18
7E 30 30 31 34 30 20 31 38 0D
Volume +
~XX140 19
7E 30 30 31 34 30 20 31 39 0D
Brightness
~XX140 20
7E 30 30 31 34 30 20 32 30 0D
Menu
~XX140 21
7E 30 30 31 34 30 20 32 31 0D
Zoom
~XX140 28
7E 30 30 31 34 30 20 32 38 0D
Contrast
~XX140 47
7E 30 30 31 34 30 20 34 37 0D
Source
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------SEND from projector automatically
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Projector Return
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------System status
INFOn
n : 0/1/2/3/4/6/7/8 = Standby/Warming/Cooling/Out of Range/
Lamp fail/Fan Lock/Over Temperature/Lamp Hours Running Out
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
3
59
English
Appendices
READ from projector
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------232 ASCII Code HEX Code
Function
Projector Return
Description
--------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------~XX121 1
7E 30 30 31 32 31 20 31 0D
Input Source Commands
OKn
n: 0/1/2/3/4/5= None/VGA1/VGA2/Video/S-Video/HDMI
~XX122 1
7E 30 30 31 32 32 20 31 0D
Sofware Version
OKdddd
dddd: FW version
~XX123 1
7E 30 30 31 32 33 20 31 0D
Display Mode
OKn
n: 0/1/2/3/4/5/6/7
None/Presentation/Bright/Movie/sRGB/User/Blackboard/3D
~XX124 1
7E 30 30 31 32 34 20 31 0D
Power State
OKn
n : 0/1 = Off/On
~XX125 1
7E 30 30 31 32 35 20 31 0D
Brightness
OKn
~XX126 1
7E 30 30 31 32 36 20 31 0D
Contrast
OKn
~XX127 1
7E 30 30 31 32 37 20 31 0D
Aspect Ratio
OKn
n : 0/1/2/3 = 4:3/16:9/Native/AUTO (SVGA/XGA)
n: 0/1/2/3 = 4:3/16:9 or 16:10/Native/AUTO (WXGA)
*16:9 or 16:10 depend on Screen Type setting
~XX128 1
7E 30 30 31 32 38 20 31 0D
Color Temperature
OKn
n : 0/1/2 = Warm/Medium/Cold
~XX129 1
7E 30 30 31 32 39 20 31 0D
Projection Mode
OKn
n : 0/1/2/3 = Front-Desktop/Rear-Desktop/Front-Ceiling/Rear-Ceiling
~XX150 1
7E 30 30 31 35 30 20 31 0D
Information
OKabbbbccdddde
a : 0/1 = Off/On
bbbb: Lamp Hour
cc: source
00/01/02/03/04/05/= None/VGA1/VGA2/Video/S-Video/HDMI
dddd: FW version
e : Display mode 0/1/2/3/4/5/6/7
None/Presentation/Bright/Movie/sRGB/User/Blackboard/3D
~XX151 1
7E 30 30 31 35 31 20 31 0D
Model name
OKn
n:1/2/3= SVGA/ XGA/ WXGA
~XX108 1
7E 30 30 31 30 38 20 31 0D
Lamp Hours
OKbbbb
bbbb: Lamp Hour
~XX108 2
7E 30 30 31 30 38 20 31 0D
Cumulative Lamp Hours
OKbbbbb
bbbbb: (5 digits) Total Lamp Hours
~XX321 1
7E 30 30 33 32 31 20 31 0D
Filter Usage Hours
OKbbbb
bbbb: Filter Usage Hours
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
English
60
4
Appendices
Ceiling Mount Installation
1. To prevent damage to your projector, please use the
InFocus ceiling mount.
2. If you wish to use a third party ceiling mount kit, please
ensure the screws used to attach a mount to the projector
meet the following specifications:
Screw type: M4*3
Minimum screw length: 10mm
Please note that
damage resulting
from incorrect
installation will void
the warranty.
47.95
39.88
13.50
Lens
127.45
186.65
314.10
55.00
82.30
63.90
85.00
77.30
223.50
Warning:
1. If you buy a ceiling
mount from another
company, please
be sure to use the
correct screw size.
Screw size will vary
depending on the
thickness of the
mounting plate.
2. Be sure to keep
at least 10 cm gap
between the ceiling
and the bottom of the
projector.
3. Avoid installing the
projector near a heat
source.
127.45
8.00
Unit: mm
61
English
Appendices
Regulation & Safety Notices
This appendix lists the general notices of your projector.
FCC notice
This device has been tested and found to comply with the
limits for a Class B digital device pursuant to Part 15 of the
FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This device generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this device does cause
harmful interference to radio or television reception, which can
be determined by turning the device off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/television
technician for help.
Notice: Shielded cables
All connections to other computing devices must be
made using shielded cables to maintain compliance with
FCC regulations.
Caution
Changes or modifications not expressly approved by the
manufacturer could void the user’s authority, which is
granted by the Federal Communications Commission, to
operate this projector.
English
62
Appendices
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions:
1.This device may not cause harmful interference and
2.This device must accept any interference received,
including interference that may cause undesired
operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian
ICES-003.
Remarque à l’intention des utilisateurs
canadiens
Cet appareil numerique de la classe B est conforme a la
norme NMB-003 du Canada.
Declaration of Conformity for EU
countries
• EMC Directive 2004/108/EC (including amendments)
• Low Voltage Directive 2006/95/EC
• R & TTE Directive 1999/5/EC (if product has RF function)
Disposal instructions
Do not throw this electronic device into the
trash when discarding. To minimize pollution
and ensure utmost protection of the global
environment, please recycle it.
63
English