Air velocity, Air flow, Type K/J thermometer
Real time data logger, 16000 Data logger no., RS232
ANEMOMETER
Model : DAF2005MDL
TABLE OF CONTENTS
1. FEATURES................................................................ 1
2. SPECIFICATIONS...................................................... 2
3. FRONT PANEL DESCRIPTION.....................................6
4. GENERAL MEASURING PROCEDURE........................... 8
4-1 Air velocity/Air temperature measurement.............8
4-2 Air flow ( CMM, CFM ) measurement..................... 9
4-3 Thermocouple ( Type K/J ) Thermometer
measurement......................................................10
4-4 Data Hold............................................................11
4-5 Data Record (Max., Min. reading)......................... 11
4-6 Data Logger........................................................ 12
5. ADVANCED ADJUSTMENT PROCEDURE.......................14
5-1 Check Memory Space...........................................15
5-2 Clear Memory......................................................15
5-3 Date/Time Setting................................................15
5-4 Sample Time Setting............................................16
5-5 Auto Power Off Default Setting.............................16
5-6 Temp. Unit Default Setting................................... 16
5-7 Air Velocity Unit Default Setting............................ 17
5-8 Air Flow Unit Default Setting.................................17
5-9 Area Size ( Air Flow ) Default Setting.................... 17
5-10 Escape from the SETTING function..................... 18
6. HOW TO SEND THE DATA OUT FROM THE METER......18
7. RS232 PC SERIAL INTERFACE....................................21
8. BATTERY REPLACEMENT........................................... 23
9. SYSTEM RESET......................................................... 23
10. OPTIONAL ACCESSORIES........................................ 24
1. FEATURES
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Air velocity : m/S, Ft/min, Km/h, Knots, Mile/h,
Air flow : CMM ( m^3/min. ) and CFM ( ft^3/min. ).
Air temperature ( ℃, ℉ )
Type K/ Type J thermocouple thermometer.
Real time data logger, build in clock ( hour-min.-sec.,
year-month-date ).
Auto or manual data record, 16,000 Data logger no.
Wide sampling time adjustment range from two
seconds to 8 hours 59 minutes 59 seconds.
RS232 computer interface.
Can default auto power off or manual power off.
Can default the air velocity, air flow, Temp. unit.
Air flow measurement can set the area dimension.
Multi function with easy operation
Low-friction ball vane wheels make sure high accuracy
in high & low velocities.
Metal vane, high reliability.
Large LCD with multiple display.
Data hold, record max. and min. reading.
Microcomputer circuit provides special function & offer
high accuracy.
Air Temp. used thermistor sensor, fast response time.
Power by UM3 ( 1.5 V ) x 4 batteries or DC 9V adapter.
RS232 PC serial interface.
Separate probe, easy for operation of different
measurement environment.
Wide applications: use this anemometer to check air
conditioning & heating systems, measure air velocities,
wind temperature...etc.
1
2. SPECIFICATIONS
2-1 General Specifications
Circuit
Display
Measurement
Unit
Custom one-chip of microprocessor LSI
circuit.
LCD size : 58 mm x 34 mm.
Air velocity:
m/S (meters per second)
Km/h ( kilometers per hour )
Ft/min ( feet per minute )
Knots ( nautical miles per hour )
Mile/h ( miles per hour )
Air flow:
CMM ( m^3/min., cube meter per min. )
CFM ( m^3/min., cube feet per min. )
Air temperature:
℃, ℉
Type K/ Type J thermometer.
℃, ℉
Sampling Time Manual Push the data logger button
of Data Logger
once will save data one time.
Sensor
Structure
Auto
@ Set the sampling time to
0 second
2 sec to 8 hour 59 min. 59 sec.
Air velocity & Air flow :
Conventional twisted van arm and low
friction ball bearing design, vane use
metal material.
Air temperature :
Thermistor.
Type K/ Type J thermometer.
Thermocouple
2
Temperature
Compensation
Data Hold
Memory Recall
Sampling Time
of display
Power off
Data Output
Operating
Temperature
Operating
Humidity
Power Supply
Automatic temp. compensation for the
Type K/J thermometer.
Freeze the display reading.
Maximum & Minimum value.
Approx. 1 second.
Auto shut off saves battery life or
manual off by push button.
RS 232 PC serial interface.
0 to 50 ℃.
Less than 80% R.H.
DC 1,5 V battery ( UM3 ) x 4 PCs,
* main instrument ( Heavy duty type ).
DC 9V adapter input.
Power Supply
@ AC/DC power adapter is optional.
DC 3V silver battery.
* clock module
Type : CR2032.
Power Current Approx. DC 21.5 mA
@ Main instrument.
DC 27.5 mA.
Weight
Dimension
@ Main instrument. + Anemometer probe.
515 g/ 1.13 LB. @ Battery is included.
Main instrument :
203 x 76 x 38 mm
Anemometer sensor head :
Accessories
Included
Round, 72 mm Dia.
Instruction manual......................1
Anemometer probe..................... 1
DC 3V silver battery, CR2032.......1
Carrying case..............................1
3
PC
PC
PC
PC
Optional
Accessories
Type K thermocouple probe.
AC to DC 9V adapter.
RS232 cable, UPCB-02.
Data Acquisition software,SW-U801-WIN.
Data Logger software, SW-DL2005.
2-2 Electrical Specifications (23± 5 ℃)
Air velocity
Measurement
m/S
Km/h
Mile/h
Knots
Ft/min
Range
Resolution Accuracy
0.4 - 30.0 m/S
0.1 m/S
± ( 2%+0.2 m/S)
1.4 - 108.0 Km/h 0.1 Km/h ± ( 2%+0.8 Km/h)
0.9 - 67.0 Mile/h 0.1 Mile/h ± ( 2%+0.4 Mile/h)
0.8 - 58.3 Knots
0.1 Knots ± ( 2%+0.4 Knots)
80 - 5910 Ft/min 1 Ft/min ± ( 2%+40 Ft/min)
Air flow
Measurement Range
Resolution Area
CMM (m^3/min.) 0 to 54,000 m^3/min.
0.001-1
0.001-30.0 m^3/min.
CFM (ft^3min.).
0.01-100
0.01-322.91 ft^3/min.
0 to 1,908,300 ft^3/min.
Air temperature
Measuring Range
Resolution
Accuracy
0 ℃ to 50 ℃/32 ℉ to 122 ℉
0.1 ℃
/0.1 ℉
± 0.8 ℃/1.5 ℉
4
Type K/J thermometer
Sensor
Type
Type K
Type J
Reso- Range
lution
0.1 ℃ -50.0 to 1300.0 ℃
-50.1 to -100.0 ℃
0.1 ℉ -58.0 to 2372.0 ℉
-58.1 to -148.0 ℉
0.1 ℃ -100.0 to 1100.0 ℃
-50.1 to -100.0 ℃
0.1 ℉ -58.0 to 2012.0 ℉
-58.1 to -148.0 ℉
Accuracy
±
±
±
±
±
±
±
±
(
(
(
(
(
(
(
(
0.2
0.2
0.2
0.2
0.2
0.2
0.2
0.2
%
%
%
%
%
%
%
%
+
+
+
+
+
+
+
+
0.5 ℃
1℃)
1℉)
1.8 ℉
0.5 ℃
1℃)
1℉)
1.8 ℉
)
)
)
)
@ Above specification tests under the environment RF
Field Strength less than 3 V/M & frequency less than
30 MHz only.
5
3. FRONT PANEL DESCRIPTION
6
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
3-12
3-13
3-14
3-15
3-16
3-17
3-18
3-19
3-20
3-21
Display
Power Button
HOLD Button ( ESC Button )
REC Button ( Enter Button )
▲ Up Button
Function Button ( ▼ Down Button )
Send Button ( Clock Button )
SET Button ( Logger Button )
Stand
Battery Compartment/Cover
Tripod Fix Nut
LCD Brightness Adjust VR
System Reset Switch
RS-232 Output Terminal
DC 9V Power Adapter Input Socket
Type K/J Probe Input Socket
Probe Input Socket
Probe Lock Switch ( System On/Off Switch )
Probe Plug
Probe head ( Anemometer vane & Temperature )
Probe handle
7
4. GENERAL MEASURING
PROCEDURE
The meter default value are following :
* The air velocity unit is m/S.
* The temperature unit is ℃.
* The air flow unit is CMM.
* The air flow area is meter^2 ( meter square ).
* The sampling time of data logger function is
2 seconds.
4-1 Air velocity /Air Temp. measurement
1) Install the " Probe Plug " ( 3-19, Fig. 1 ) into the
" Probe Input Socket " ( 3-17, Fig. 1 ).
Attention :
After install the " Probe Plug ", should slide
Probe Lock Switch " ( 3-18, Fig. 1 ) to the On
position ( right position ).
2)Power on the meter by pressing the " Power Button "
( 3-2, Fig. 1 ).
3) Select measuring function by pressing " Function
Button " ( 3-6, Fig. 1 ) until the display show the
air velocity unit.
@ Air velocity measurement, the display unit
will show m/S ( or Ft/min, Km/h, Knots, Mile/h ).
@ The Air velocity unit adjustment, please refer
Chapter 5-7.
8
4) Hold the " Vane Probe Handle " ( 3-21, fig. 1 ) by hand
& let the " Vane Probe Head " ( 3-20, Fig. 1 ) face
against the measuring air flow source, then the
Display ( 3-1, Fig. 1 ) will show air velocity directly. At
the same time, the display will show the air
temperature value. @ The Temp. unit adjustment,
please refer Chapter 5-6.
Measuring Consideration :
The yellow dot mark on the sensor head
indicates the direction that " need to face
against the air flow.
4-2 Air flow ( CMM, CFM ) measurement
1) Install the " Probe Plug " ( 3-19, Fig. 1 ) into the
" Probe Input Socket " ( 3-17, Fig. 1 ).
Attention :
After install the " Probe Plug ", should slide
Probe Lock Switch " ( 3-18, Fig. 1 ) to the On
position ( right position )
2)Power on the meter by pressing the " Power Button "
( 3-2, Fig. 1 ).
3) Select measuring function by pressing " Function
Button " ( 3-6, Fig. 1 ) until the display show the
air flow unit ( CMM or CFM ).
@ Air flow measurement, the display unit
will show CMM ( or CFM ).
@ CMM : cube meter per minute.
CFM : cube feet per minute.
@ The air flow unit adjustment, please refer Chapter 5-8.
9
4)The display's bottom left side will show area size in
Meter^2 ( or Ft^2 ) when make the air flow
measurement.
@ Meter^2 : Meter square, Ft^2 : Feet square.
@ The adjusting procedures of area size, please refer
Chapter 5-9.
5) Hold the " Vane Probe Handle " ( 3-21, fig. 1 ) by hand &
let the " Vane Probe Head " ( 3-20, Fig. 1 ) is opposite to
the measuring air flow source, then the Display ( 3-1,
Fig. 1 ) will show air flow value.
Measuring Consideration :
The yellow dot mark on the sensor head
indicates the direction that " need to face
against the air flow.
4-3 Thermocouple ( Type K/J ) Thermometer
measurement
1)Not install the anemometer " Probe Plug " ( 3-19,
Fig. 1 ) into the " Probe Input Socket " ( 3-17, Fig. 1 )
Attention :
After take away the anemometer " Probe
Plug " , then should slide Probe Lock
Switch " ( 3-18, Fig. 1 ) to the On position
( right position )
2)Plug the Thermocouple Temp. Probe ( Type K Temp.
probe pr Type J Temp. probe, optional ) into " Type
K/J Probe Input Socket " ( 3-16, Fig. 1 )
10
3)Power on the meter by pressing the " Power Button "
( 3-2, Fig. 1 ).
4) For the Type K Probe, press the " Function Button "
( 3-6, Fig. 1 ) to let the bottom right LCD show the
" K type " indicator
For the Type J Probe, press the " Function Button "
( 3-6, Fig. 1 ) to let the bottom right LCD show the
" J type " indicator
4-4 Data Hold
During the measurement, press the " Hold Button " ( 3-3,
Fig. 1 ) once will hold the measured value & the LCD will
display a " HOLD " symbol.
* Press the " Hold Button " once again will release the data
hold function.
4-5 Data Record ( Max., Min. reading )
* The data record function records the maximum and
minimum readings. Press the " REC Button " ( 3-4, Fig.
1 ) once to start the Data Record function and there
will be a " REC. " symbol on the display.
* With the " REC. " symbol on the display :
a) Press the " REC Button " ( 3-4, Fig. 1 ) once, the "
REC. MAX. " symbol along with the maximum value
will appear on the display.
If intend to delete the maximum value, just press
the " Hold Button " ( 3-3, Fig. 1 ) once, then the
display will show the " REC. " symbol only & execute
the memory function continuously.
11
b)Press the " REC Button " ( 3-4, Fig. 1 ) again, the
" REC. MIN. " symbol along with the minimum value
will appear on the display.
If intend to delete the minimum value, just press
the " Hold Button " ( 3-3, Fig. 1 ) once, then
the display will show the " REC. " symbol only &
execute the memory function continuously.
c) To exit the memory record function, just press the
" REC " button for 2 seconds at least. The display will
revert to the current reading.
4-6 Data Logger
The data logger function can save 16,000 measuring
data with the clock time ( Real time data logger, build
in clock ( hour-min.-sec., year-month-date ).
The data logger procedures are as following :
a) If push the Logger Button " ( 3-8, Fig. 1 ) once will
show the sampling time value on the bottom left
display then disappeared.
b)Press the " REC Button " ( 3-4, Fig. 1 ) once to
start the Data Record function and there will be a
" REC. " symbol on the display.
c) Auto Data Logger ( Sampling time set from
2 seconds to 8 hours 59 minutes 59 seconds )
Press the " Logger Button " ( 3-8, Fig. 1 ) once to start
the Auto Data Logger function, at the same the
bottom right display will show the indicator "
Recording.... ", now the Data Logger function is
executed. The upper display will show DATA "
indicator along with " REC " marker.
12
d)Manual Data Logger ( Sampling time set to 0
second )
Press the " Logger Button " ( 3-8, Fig. 1 ) once will
save the data one time into the memory, at the same
time the bottom right display will show the indicator
" Recording.... " a while. Now the Data logger function is
executed. The upper display will show " DATA "
indicator along with " REC " marker.
e) Memory full
Under execute the data logger, if the bottom right
display show the " Full ", it indicate the memory data
already over 16,000 no. and the memory is full.
f) During the Data Logger function is executed, press the "
Logger Button " ( 3-8, Fig. 1 ) once will stop to execute
the data logger function, the " DATA " indicator
will be disappeared.
If press the " Logger Button " ( 3-8, Fig. 1 ) once again
will continuous the Data Logger function.
Remark :
1) If intend to change the data logger sampling time,
please refer chapter 5-4.
2) If intend to know the space of balance data numbers
into the memory IC, please refer chapter 5-1.
3) If intend to clear the saving data from the memory
please refer chapter 5-2.
13
5. ADVANCED ADJUSTMENT
PROCEDURES
When execute the following Advanced
Adjustment Procedures should cancel the " Hold
function " and the " Record function " first. The
display will not show the " HOLD " and the " REC "
marker.
a. Press the " SET Button " ( 3-8, Fig. 1 ) at least two
seconds until the lower display show
XXXXX
Memory Space
* If push the " ESC Button " ( 3-3, Fig. 1 ) will escape
the selecting function and return to the normal
measuring display.
b. One by one to press the " Set Button " ( 3-8, Fig. 1 )
once a while to select the ten main function, at the
same time lower display will show on the lower
display will show on the lower display as :
Memory Space
Clear Memory
Date/Time Set
Sample Time
Auto Power Off
Temp. Unit
Default Vel.
Default FLOW
Area
ESC→Finish
14
c. When make Advanced Adjustment Procedure
will use the following key buttons :
ESC Button ( 3-3, Fig. 1 ), Enter Button ( 3-4, Fig. 1 )
▲ Up Button ( 3-5, Fig. 1 ), ▼ Down Button ( 3-6, Fig. 1 )
SET Button ( 3-8, Fig. 1 ), SEND Button ( 3-7, Fig. 1 )
5-1 Check Memory Space
To check the balance data numbers that exist into the
memory ( allow memorize data no. ).
XXXXX
Memory Space
@ XXXXX is the balance data numbers, for example
XXXXX=15417.
5-2 Clear Memory
* To delete the existing save data numbers from the
memory.
* Push ENTER Button once, then push ENTER Button
to confirm.
* Press the ESC Button once to quite and return to
the main measurement manual.
5-3 Date/Time Setting
* Use ▲ Up Button, ▼ Down Button and
Enter ( →) Button to select the expect Date
( year-month-date ) and the time (HOUR-MIN.-SEC.).
* After finish the Date/Time adjustment,
Push the " Enter Button " , then press the " ESC Button "
will quite and save the clock data into the memory.
15
5-4 Sample Time Setting
* Use ▲ Up Button, ▼ Down Button and Enter ( →)
Button to select the expect Sample Time ( HOUR-MIN.-SEC.).
* After finish the Sample Time adjustment,
Push the " Enter Button " , then press the " ESC Button "
will quite and save the clock data into the memory.
5-5 Auto Power Off Default Setting
* Use ▲ Up Button, ▼ Down Button to select " 1 " or
" 0 ".
1 = Auto power On.
0 = Auto power Off.
* After finish the Auto Power Off adjustment,
push the " Enter Button " , then press the " ESC Button "
will quite and return to the normal measurement
display.
5-6 Temp. Unit Default Setting
* Use ▲ Up Button, ▼ Down Button to select " 1 " or
" 0 ".
1=℉
0=℃
* After finish the Temperature unit adjustment,
push the " Enter Button " , then press the " ESC Button "
will quite and return to the normal measurement
display.
16
5-7 Air Velocity Unit Default Setting
* Use ▲ Up Button, ▼ Down Button to select the
default Air Velocity unit as :
m/S, Ft/min, Km/h, Knots, Mile/h,
* After finish the Air Velocity unit adjustment,
push the " Enter Button " , then press the " ESC Button "
will quite and return to the normal measurement
display.
5-8 Air Flow Unit Default Setting
* Use ▲ Up Button, ▼ Down Button to select the
default Air Flow unit as : CMM or CFM
CMM : cube meter per minute.
CFM : cube feet per minute.
* After finish the Air Flow unit adjustment, push the "
Enter Button " first, then press the " ESC Button " again
will quite and return to the normal measurement display.
5-9 Area Size ( Air Flow ) Default Setting
* Use ▲ Up Button, ▼ Down Button and the SEND ( → )
to select the desired area value.
@ If the 5-8 select the CMM, the area unit is
Meter^2 ( Meter square ) and the adjust range
is limited to 0.001 to 30.000 Meter square.
@ If the 5-8 select the CFM, the area unit is
Feet^2 ( Feet square ) and the adjust range
is limited to 0.01 to 322.92 Feet square.
* After finish the Area Size adjustment, push the
" Enter Button " first, then press the " ESC Button " again
will quite and return to the normal measurement display.
17
5-10 Escape from the SETTING function
Press the " ESC Button " once a while will quite and
return to the normal measurement display.
6. HOW TO SEND THE DATA OUT
FROM THE METER
1)If intend to send the data out from the meter, it
should cancel the " Hold function " and the " Record
function " first. The display will not show the " HOLD "
and the " REC " marker.
2)Press the " SEND Button " ( 3-7, Fig. 1 ) at least 2
seconds until the bottom right display show " Transmit
mode ", then release the button.
LCD display will show the fowling screen
alternately.
0.3
m/S
1
Block no.
1
←
→
Transmit mode
The first
data of
each block
m/S
xx:xx:xx Transmit mode
Start time
of each
block
Start data
address of
each block
Use ▲ Up Button, ▼ Down Button to select the
different data memory block no. ( 1 to 250 ).
18
The meter can save 16,000 data max. , those
data will saved into 250 memory block max.
* One " Memory Block " means :
The data that save into one routine Data Logger
procedures ( Push " REC " button , following push
the " Logger " button to save the data, the display
will show the " REC " and " DATA " . After save the
data push the " Logger " button, following push
the " REC " button, will exist the Data Logger
function. The " REC " and " DATA " indicator of LCD
will be disappeared ). Please refer Chapter 4-6,
page 12.
Block 1
↓
Block 2
↓
..................
..................
↓
Block 250
Data 1
to
Data X
Data X+1
to
Data Y
Data Z
to
Data 16,000
19
3) Until the desired Memory Block no. be selected.
Push the " Send Button " ( 3-7, Fig. 1 ) once, the
data in the Memory Block will send out.
During the data send out, the bottom right display will
show the " Sending Data ! " indicator. When data
already send out completely, the bottom right display
will show the Transmit mode " indicator again.
5) Push the " ESC Button " ( 3-3, Fig. 1 ) will exist
the data sending function and return to the normal
display.
Remarks :
@ If intend up load the data to the computer,
then should connect the RS232 cable
( optional, model : UPCB-02) and apply the
Data Logger software ( optional, Model :
SW-DL2005 ).
@ When sending the data, each time just can
send one Memory Block data out. for example
block 1 data, block 2 data... or block 250 data.
20
7. RS232 PC SERIAL INTERFACE
The instrument has RS232 PC serial interface via a 3.5
mm terminal ( 3-14, Fig. 1 ).
The data output is a 16 digit stream which can be
utilized for user's specific application.
A RS232 lead with the following connection will be
required to link the instrument with the PC serial port.
Meter
PC
(9W 'D" Connector)
(3.5 mm jack plug)
Center Pin........................Pin 4
Ground/shield.....................Pin 2
Pin 5
2.2 K
resister
The 16 digits data stream will be displayed in the
following format :
D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0
21
Each digit indicates the following status :
D0
End Word = 0D
D1 & D8 Display reading, D1 = LSD, D8 = MSD
For example :
If the display reading is 1234, then D8 to
D1 is : 00001234
D9
Decimal Point(DP), position from right to the
left
0 = No DP, 1= 1 DP, 2 = 2 DP, 3 = 3 DP
D10
Polarity
0 = Positive 1 = Negative
D11 &
Annunciator for Display
D12
℃ = 01
Knot = 09
mile/h = 12
℉ = 02
Km/h = 10
CMM = 84
m/S = 08
ft/min = 11
CFM = 85
D13
When send the upper display data = 1
When send the lower display data = 2
D14
4
D15
Start Word = 02
RS232 setting
Baud rate
9600
Parity
No parity
Data bit no.
8 Data bits
Stop bit
1 Stop bit
22
8. BATTERY REPLACEMENT
1) The time to change the UM3 ( 1.5 V ) x 4 PCs
When the left corner of LCD display show "
", it
is necessary to replace the batteries ( UM3/1.5 V x 4 PCs ).
The time to change the CR2032 ( 3V silver battery )
When the clock is not accurate or power off the meter
then on, the clock time is disappeared or garbled, it is
necessary to replace the battery ( CR2032 )
2)Slide the " Battery Cover " ( 3-10, Fig. 1 ) away from the
instrument and remove the battery.
3)Replace with batteries ( UM3/1.5 V x 4 PCs or CR2032 )
and reinstate the cover.
4)Make sure the battery cover is secured after changing
the battery.
9. SYSTEM RESET
If the meter happen the troubles such as :
CPU system is hold ( for example, the key button can
not be operated... ).
Then make the system RESET will fix the problem.
The system RESET procedures will be either following
method :
23
1)Slide the " Probe Lock Switch/System On/Off
Switch " from the On to Off, then On again.
2)Or during the Power On, used a pin tool to push
the " System Reset Switch " ( 3-13, Fig. 1 ) once
a while.
10. OPTIONAL ACCESSORIES
RS232 cable
UPCB-02
Data Logger
software
SW-DL2005
Data Acquisition
software
SW-U801-WIN
* Isolated RS232 cable.
* Used to connect the meter to
the computer
* Software the used to download
the data logger ( data recorder )
from the meter to computer.
* The SW-U801-WIN is a multi
displays ( 1/2/4/6/8 displays )
powerful application software,
provides the functions of data
logging system, text display,
angular display, chart display,
data recorder high/low limit, data
query, text report, chart report..
.xxx.mdb data file can be
retrieved for EXCEL, ACESS..,
wide intelligent applications.
24
Thermocouple
Probe
(Type K) TP-01
Thermocouple
Probe
(Type K), TP-02A
Thermocouple
Probe
(Type K), TP-03
Surface Probe
(Type K), TP-04
* Measure Rage: -40 ℃ to 250 ℃,
-40 ℉ to 482 ℉.
* Max. short-tern operating
Temperature: 300 ℃ (572 ℉).
* It is an ultra fast response
naked-bead thermocouple
suitable for many general purpose
application.
* Measure Range: -50 ℃ to 900 ℃,
-50 ℉ to 1650 ℉.
* Dimension:10cm tube, 3.2mm Dia.
* Measure Range: -50 ℃ to 1200 ℃,
-50 ℉ to 2200 ℉.
* Dimension: 10cm tube, 8mm Dia.
* Measure Range: -50 ℃ to 400 ℃,
-50 ℉ to 752 ℉.
* Size :
Temp. sensing head - 15 mm Dia.
Probe length - 120 mm.
25
0501-DAF2005MDL