TN-5510A-2GLSX-ODC and TN-5510A-8POE-2GLSX-ODC

TN-5510A-2GLSX-ODC and
TN-5510A-8POE-2GLSX-ODC
Hardware Installation Guide
Moxa ToughNet Switch
First Edition, July 2014
 2014 Moxa Inc. All rights reserved.
Reproduction without permission is prohibited.
P/N: 1802055100060
Overview
The ToughNet TN-5510A-2GLSX-ODC and TN-5510A-8POE-2GLSX-ODC
series M12 managed Ethernet switches are designed for industrial
applications in harsh environments. The TN series switches use M12
connectors to ensure tight, robust connections, and guarantee reliable
operation against environmental disturbances, such as vibration and
shock. The wide 24 to 110 VDC range with dual power inputs (non-PoE
series) increases the reliability of your communications.
The TN-5510A-2GLSX-ODC and TN-5510A-8PoE-2GLSX-ODC switches
provide up to 8 Fast Ethernet M12 ports, and 2 ports on the down side to
provide the Gigabit fiber interface with an embedded 2 km multimode
fiber transceiver. Moreover, the -40 to 75°C operating temperature and
IP54-rated waterproof enclosure allow deployment in harsh
environments. The TN-5510A Ethernet switch is compliant with the
essential sections of EN 50155 (railway applications), making it suitable
for a variety of industrial applications.
Package Checklist
The ToughNet TN-5510A-2GLSX-ODC and TN-5510A-8POE-2GLSX-ODC
switches are shipped with the following items. If any of these items are
missing or damaged, please contact your customer service
representative for assistance.
•
•
•
•
•
•
•
1 Moxa ToughNet switch
M12 to DB9 console port cable
2 protective caps for console and relay output ports
Panel mounting screws
CD-ROM with user’s manual
Hardware installation guide
Warranty card
Features
Anti-Vibration Circular Connectors for Robust Links
•
•
•
•
M12 D-coding 4-pin female connectors for Fast Ethernet
10/100BaseT(X) ports
Fiber-optic ODC connectors with embedded 2 km Gigabit Ethernet
1000BaseLSX
M12 A-coding 5-pin male connectors for console and relay output
M23 6-pin male connector for power input
Dual Power Inputs
•
Supports 24-110 VDC (16.8 to 137.5 VDC)
High Performance Network Switching Technology
•
•
•
•
•
•
IEEE 1588 PTP (Precision Time Protocol) for precise time
synchronization of networks
DHCP Option 82 for IP address assignment with different policies
EtherNet/IP and Modbus/TCP industrial Ethernet protocols supported
Turbo Ring and Turbo Chain (recovery time <20 ms @250 switches),
and STP/RSTP/MSTP for network redundancy
IGMP Snooping and GMRP for filtering multicast traffic from industrial
Ethernet protocols
Port-based VLAN, IEEE802.1Q VLAN, and GVRP protocol to ease
network planning
-2-
•
•
•
•
•
•
•
•
•
•
•
•
•
•
QoS (IEEE 802.1p/1Q and ToS/DiffServ) allows real-time traffic
classification and prioritization
802.3ad, LACP for optimum bandwidth utilization
TACACS+, SNMPv3, IEEE 802.1X, HTTPS, and SSH to enhance
network security
SNMP v1/v2c/v3 for different levels of network management
RMON for efficient network monitoring and proactive capability
Bandwidth management prevents unpredictable network status
Lock port allows access by only authorized MAC addresses
Port mirroring for online debugging
Automatic warning by exception through email, relay output
Automatic recovery of connected device’s IP addresses
Line-swap fast recovery
LLDP for automatic topology discovery in network management
software
Loop protection prevents network loops
Configurable through Web browser, Telnet/serial console, CLI, and
Windows utility
Designed for Industrial-Specific Applications
•
•
•
•
•
Two Gigabit fiber ports to meet high EMI immunity, long-distance,
and bandwidth requirements
Essential compliance with EN 50155
-40 to 75°C operating temperature range
IP54, rugged high-strength case
Panel mounting or DIN rail mounting installation capability
Recommended Optional Accessories
•
•
•
•
•
•
•
CBL-M23(FF6P)Open-BK-100-IP67: 1-meter M23 to 6-pin power
cable with IP67-rated female 6-pin M23 connector
CBL-M12D(MM4P)/RJ45-100 IP67: 1-meter M12-to-RJ45 Cat-5E UTP
Ethernet cable with IP67-rated male 4-pin M12 D-coded connector
CBL-M12(FF5P)/OPEN-100 IP67: 1-meter M12-to-5-pin power cable
with IP67-rated female 5-pin M12 A-coded connector
M12D-4P-IP68: Field-installable M12 D-coded screw-in connector,
male 4-pin, IP68-rated
M12A-5P-IP68: Field-installable M12 A-coded screw-in connector,
female 5-pin, IP68-rated
CAP-M12F-M: Metal cap for M12 female connector
DK-DC50131: DIN rail mounting kit, 50 x 131 mm
-3-
TN-5510A-2GLSX-ODC Panel Layouts
1.
2.
3.
4.
5.
6.
7.
Screw holes for panel mounting kit
Console port
Grounding screw
Relay output port
Power input voltage range indicator
Power input port (male 6-pin shielded M23 connector)
PWR1 LED: for power input 1
-4-
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
PWR2 LED: for power input 2
FAULT LED
MSTR/HEAD LED: for ring master or chain head
CPLR/TAIL LED: for ring coupler or chain tail
TP port’s 10/100 Mbps LED
10/100BaseT(X) port (female 4-pin shielded M12 connector with D
coding)
Waterproof vent
Product label
12 screw holes for DIN rail mounting kit
E2 LED: Down-side E2 Gigabit port’s 1000 Mbps LED
E1 LED: Down-side E1 Gigabit port’s 1000 Mbps LED
Gigabit fiber port E1 (corresponding to port 9 in the TN-5510A User’s
Manual)
Gigabit fiber port E2 (corresponding to port 10 in the TN-5510A
User’s Manual)
ATTENTION
Please DO NOT open or remove vent 15. The warranty will be
invalid if the seal is removed.
All exposed connectors, including 3, 5, 7, and 14, should be
tightly covered by protective caps when they are not in use to
ensure IP54 protection.
-5-
Mounting Dimensions (unit = mm)
TN-5510A-2GLSX-ODC Series
-6-
TN-5510A-8PoE-2GLSX-ODC Series
-7-
Panel/Wall Mounting
STEP 1:
Mounting the TN-5510A to a wall requires 4 screws. Use the ToughNet
switch as a guide to mark the correct positions of the 4 screws.
STEP 2:
Use the 4 screws in the panel mounting kit. If you
would like to use your own screws, make sure the
screw head is between 6.0 mm and 7.0 mm in
diameter and the shaft is less than 4.0 mm in
diameter, as shown at the right.
Do not screw the screws in all the way—leave a
space of about 2 mm to allow room for sliding the ToughNet switch
between the wall and the screws.
NOTE
Before tightening the screws into the wall, make sure the screw
head and shaft size are suitable by inserting the screw through
one of the keyhole-shaped apertures of the ToughNet switch.
STEP 3:
Once the screws are fixed in the wall, hang the ToughNet switch on the 4
screws through the large opening of the keyhole-shaped apertures, and
then slide the switch downwards. Tighten the four screws for added
stability.
NOTE
To provide greater protection from vibration and shock, use
screws with shaft diameter between 6.0 mm and 7.0 mm, and fix
the ToughNet switch onto the wall directly through the large
opening of the keyhole-shaped apertures.
-8-
DIN Rail Mounting (optional)
Use a pair of optional DK-DC50131 DIN
rail mounting kits (must be purchased
separately) to mount the TN-5510A on
a 35 mm DIN rail.
STEP 1:
Use 12 screws (6 screws per plate) to
attach the two DIN rail attachment
plates to the rear panel of the switch.
STEP 2:
If the spring-loaded bracket is locked in place, push the recessed button
to release it. Once released, you should feel some resistance from the
spring as you slide the bracket up and down a few millimeters in each
direction.
STEP 3:
Insert the top of the DIN rail into
the top slot of the DIN rail
attachment plates.
STEP 4:
The DIN rail attachment plates will
snap into position, as shown in the
figure below.
To remove the Moxa ToughNet Switch from the DIN rail, use a
screwdriver to pull down the bottom parts of the two spring-loaded
brackets until they are fixed in the “locked” position, and then reverse
Steps 3 and 4 above.
-9-
Wiring Requirements
WARNING
Turn the power off before disconnecting modules or wires. The
correct power supply voltage is listed on the product label. Check
the voltage of your power source to make sure you are using the
correct voltage. Do NOT use a voltage greater than what is
specified on the product label.
These devices must be supplied by a SELV source as defined in
the Low Voltage Directive 2006/95/EC and 2004/108/EC.
ATTENTION
Safety First!
Observe all electrical codes dictating the maximum current
allowable for each wire size. If the current goes above the
maximum ratings, the wiring could overheat, causing serious
damage to your equipment.
ATTENTION
Safety First!
Be sure to disconnect the power cord before installing and/or
wiring your Moxa switch.
This device has UL 508 approval. Use copper conductors only,
60/75°C, and tighten to 4.5 pound-inches. For use in pollution
degree 2 environments.
Please read and follow these guidelines:
•
Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
NOTE
•
•
•
Do not run signal or communications wiring and power wiring
through the same wire conduit. To avoid interference, wires with
different signal characteristics should be routed separately.
You can use the type of signal transmitted through a wire to
determine which wires should be kept separate. The rule of thumb is
that wiring that shares similar electrical characteristics can be
bundled together.
Keep input wiring and output wiring separated.
It is strongly advised that you label wiring for all devices in the system
when necessary.
- 10 -
Grounding the ToughNet Switch
Grounding and wire routing help limit the effects of noise due to
electromagnetic interference (EMI). Run the ground connection from the
grounding screw to the grounding surface prior to connecting devices.
ATTENTION
This product is intended to be mounted to a well-grounded
mounting surface such as a metal panel.
Connecting the Power Supplies
In non-PoE switches, the ToughNet TN-5510A series switches support
two sets of power input—power input 1 and power input 2. The M23 6-pin
male connector on the TN-5510A non-PoE switches’ front panel is used for
the dual power inputs.
Pinouts for the power input port on the TN-5510A (non-PoE
series)
Pinouts for the power input port on the TN-5510A-PoE series
- 11 -
Pinouts for the power input port on the TN-5510A
Pin
1
2
3
4
5
Description
PWR1 Live / DC +
Usage
Connect “PWR1 Live / DC +” to the positive
(+) terminal when using a DC power source.
PWR1 Neutral / DC - Connect “PWR1 Neutral / DC –“ to the
negative (-) terminal when using a DC power
source.
Chassis Ground
Connect the “Chassis Ground” to the
equipment ground bus for DC inputs.
PWR2 Neutral / DC - Connect “PWR2 Neutral / DC –” to the
negative (-) terminal when using a DC power
source.
PWR2 Live / DC +
Connect “PWR2 Live / DC +” to the positive
(+) terminal when using a DC power source.
STEP 1:
Plug your power cord’s M23 connector into the power input port of the
TN-5510A switch.
STEP 2:
Screw the nut on your power cord connector to the power input connector
on the switch to ensure a tight connection.
ATTENTION
Before connecting the TN-5510A to the power input, make sure
the power source voltage is stable.
Connecting the Relay Outputs
Each TN-5510A switch has two sets of relay outputs—relay output 1 and
relay output 2. The M12 A-coded 5-pin male connector on the TN-5510A’s
front panel is used for the two relay outputs. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay contacts from
the switch. You may purchase an M12 power cable from Moxa. The model
number of the cable, which must be purchased separately, is CBL-M12
(FF5P)/OPEN-100 IP67.
Pinouts for the relay output port on TN-5510A
N.C.: Not connected
FAULT:
The two sets of relay contacts of the M12 A-coded 5-pin male connector
are used to detect user-configured events. The two wires attached to the
fault contacts form an open circuit when a user-configured event is
triggered. If a user-configured event does not occur, the fault circuit
remains closed.
- 12 -
RS-232 Connection
The TN switch has one RS-232 (M12 5-pin) console port, located on the
front panel. Use an M12-to-DB9 console cable to connect the TN switch’s
console port to your PC’s COM port. You may than use a console terminal
program, such as Moxa PComm Terminal Emulator to access the TN
switch’s configuration utility.
M12 Console Port Pinouts
Connecting the Data Lines
10/100BaseT(X) Ethernet Port Connection
All TN-5510A models have 8 10/100BaseT(X) Ethernet ports (4-pin
shielded M12 connector with D coding). The 10/100BaseTX ports located
on the TN-5510A’s front panel are used to connect to Ethernet-enabled
devices. Most users configure these ports for Auto MDI/MDI-X mode, in
which case the port’s pinouts are adjusted automatically depending on
the type of Ethernet cable used (straight-through or cross-over), and the
type of device (NIC-type or HUB/Switch-type) connected to the port.
In what follows, we give pinouts for both MDI (NIC-type) ports and MDI-X
(HUB/Switch-type) ports. We also give cable wiring diagrams for
straight-through and cross-over Ethernet cables.
Pinouts for the 10/100BaseT(X) Ports on the TN-5510A
Pinouts for the 1000BaseLSX Q-ODCR Gigabit Fiber port
Mating Sequence
Push plug slightly into
connector socket
Rotate to find keying
position
Unmated – push
connector to mate
- 13 -
Mated – connector snaps Pull coupling ring to
in and is fully strain
unmate
relieved
M12 (4-pin, M) to M12 (4-pin, M) Cross-Over Cable Wiring
M12 (4-pin, M) to M12 (4-pin, M) Straight-Trough Cable Wiring
M12 (4-pin, M) to RJ45 (8-pin) Cross-Over Cable Wiring
M12 (4-pin, M) to RJ45 (8-pin) Straight-Trough Cable Wiring
ATTENTION
The protective cover must be fixed properly to ensure IP54
protection. Use a torque wrench set to a torque of 4 kgf-m when
tightening the screws. Note that applying a larger torque may
damage the plastic protective cover.
- 14 -
LED Indicators
Several LED indicators are located on the ToughNet switch’s front panel.
The function of each LED is described in the following table.
LED
Color
State
Description
System LEDs
Power is being supplied to power input
ON
PWR1.
PWR1
AMBER
Power is not being supplied to power input
OFF
PWR1
Power is being supplied to power input
ON
PWR2.
PWR2
AMBER
Power is not being supplied to power input
OFF
PWR2.
When the corresponding PORT alarm is
enabled, and a user-configured event is
ON
triggered.
FAULT
RED
When the corresponding PORT alarm is
enabled and a user-configured event is not
OFF
triggered, or when the corresponding PORT
alarm is disabled.
When the TN switch is either the Master of
ON
this Turbo Ring, or the Head of this Turbo
Chain.
When the TN switch is Ring Master of this
MSTR/
Turbo Ring and the Turbo Ring is broken, or
GREEN Blinking
HEAD
it is Chain Head of this Turbo Chain and the
Turbo Chain is broken.
When the TN switch is neither the Master of
OFF
this Turbo Ring, nor the Head of this Turbo
Chain.
When the TN switch enables the coupling
function to form a back-up path in this
ON
Turbo Ring, or it is the Tail of this Turbo
Chain.
CPLR/
GREEN
TAIL
Blinking When the Turbo Chain is down.
When the TN switch disables the coupling
OFF
function of Turbo Ring, or it is not the Tail of
the Turbo Chain.
Ports LEDs
ON
TP port’s 10 Mbps link is active.
AMBER Blinking Data is being transmitted at 10 Mbps.
TP
Off
TP port’s 10 Mbps link is inactive.
(10/
On
TP port’s 100 Mbps link is active.
100M)
GREEN Blinking Data is being transmitted at 100 Mbps.
off
TP port’s 100 Mbps link is inactive.
On
TP port’s 1000 Mbps link is active.
E1/E2
GREEN Blinking Data is being transmitted at 1000 Mbps.
(1000M)
Off
TP port’s 1000 Mbps link is inactive.
- 15 -
Specifications
Technology
Standards
Protocols
MIB
Flow Control
Switch Properties
Priority Queues
Max. Number of
Available VLANs
VLAN ID Range
IGMP Groups
Interface
Fast Ethernet
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X)
IEEE 802.3ab for 1000BaseT(X)
IEEE 802.3x for Flow Control
IEEE 802.1D for Spanning Tree Protocol
IEEE 802.1w for Rapid STP
IEEE 802.1s for Multiple Spanning Tree Protocol
IEEE 802.1Q for VLAN Tagging
IEEE 802.1p for Class of Service
IEEE 802.1X for Authentication
IEEE 802.3ad for Port Trunk with LACP
IGMP v1/v2 device, GMRP, GVRP, SNMP
v1/v2C/v3, DHCP Server/Client, DHCP Option
66/67/82, BootP, TFTP, SNTP, SMTP, RARP,
RMON, HTTP, HTTPS, Telnet, SSH, Syslog, LLDP,
IEEE 1588 PTP, IPv6, NTP Server/Client,
EtherNet/IP, Modbus/TCP
MIB-II, Ethernet-like MIB, P-BRIDGE MIB,
Q-BRIDGE MIB, Bridge MIB, RSTP MIB, RMON
MIB Group 1, 2, 3, 9
IEEE802.3x flow control, back pressure flow
control
4
64
VID 1 to 4094
256
Front cabling, M12 connector, 10/100BaseT(X)
auto negotiation speed, F/H duplex mode, and
auto MDI/MDI-X connection
Gigabit Ethernet
Down cabling, M12 connector, 1000BaseLSX
Console Port
M12 A-coding 5-pin male connector
System LED Indicators PWR1, PWR2, FAULT, MSTR/HEAD, CPLR/TAIL
Port LED Indicators
10/100M (Fast Ethernet port), 1000M (Gigabit
Ethernet port)
Alarm Contact
Two relay outputs in one M12 A-coding 5-pin
male connector with current carrying capacity of
1 A @ 30 VDC
Power Requirements
Input Voltage
WV: 24–110 VDC (16.8 to 137.5 VDC)
Input Current
TN-5510A-2GLSX-ODC Series: 0.45 A
TN-5510A-8PoE-2GLSX-ODC Series: TBD
Connection
M23, 6-pin male connector
Overload Current
Present
Protection
Reverse Polarity
Present
Protection
- 16 -
Physical Characteristics
Housing
Metal, IP54 protection (with protective caps on
unused ports)
Dimensions (W × H × D) TN-5510A-2GLSX-ODC Series:
185 x 204.3 x 76.0 mm (7.28 x 8.04 x 2.99 in)
TN-5510A-8PoE-2GLSX-ODC Series:
185 x 204.3 x 115 mm (7.28 x 8.04 x 4.53 in)
Weight
TN-5510A-2GLSX-ODC Series: 1,805 g
TN-5510A-8PoE-2GLSX-ODC Series: 2,690 g
Installation
Panel mounting, DIN-Rail mounting
(with optional kit)
Environmental Limits
Operating Temperature -40 to 75°C (-40 to 167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
Operating Humidity
5 to 95% (non-condensing)
Regulatory Approvals
Safety
UL/cUL 508 (pending)
Rail Traffic
EN50155, EN50121-3-2, EN50121-4
EMI
FCC Part 15, CISPR (EN55022) class A
EMS
EN61000-4-2 (ESD), level 3
EN61000-4-3 (RS), exceeds level 3
EN61000-4-4 (EFT), level 3
EN61000-4-5 (Surge), level 3
EN61000-4-6 (CS), level 3
EN61000-4-8
Shock
IEC61373
Freefall
IEC60068-2-32
Vibration
IEC61373
Note: Please check Moxa’s website for the most up-to-date certification
status.
Warranty
5 years
Details: See www.moxa.com/warranty
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax: 1-714-528-6778
Moxa China (Shanghai office):
Toll-free: 800-820-5036
Tel:
+86-21-5258-9955
Fax: +86-21-5258-5505
Moxa Europe:
Tel:
+49-89-3 70 03 99-0
Fax: +49-89-3 70 03 99-99
Moxa Asia-Pacific:
Tel:
+886-2-8919-1230
Fax: +886-2-8919-1231
- 17 -