2
© Siemens AG 2015
SITOP compact
2/2
2/3
2/6
Introduction
1-phase, 12 V DC
1-phase, 24 V DC
Siemens KT 10.1 · 2015
© Siemens AG 2015
SITOP compact
Introduction
■ Overview
■ More information
Select the appropriate power supply quickly and easily with the
SITOP Selection Tool:
2
http://www.siemens.com/sitop-selection-tool
The slim power supply unit for control boxes
The single-phase SITOP compact are power supplies for the
lower performance range. Thanks to the extremely space-saving
slim design, they are especially suited to distributed applications in control boxes or in small control cabinets. The series is
characterized by low power losses throughout the entire load
range. The losses are extremely low even during idling, which
means they are perfectly suited for applications that are frequently in stand-by mode. The SITOP PSU100C power supplies
have a wide-range input for AC and DC networks; plug-in terminals facilitate the electrical connection.
To further increase the 24 V availability, the SITOP compact
power supplies can be combined with DC UPS, redundancy
and selectivity modules.
Main product highlights
• 24 V DC/ 0.6 A, 1.3 A, 2.5 A, and 4 A as well as
12 V DC/ 2 A and 6.5 A
• 24 V DC/3.7 A for the supply of NEC class 2 circuits with
limited output power (100 VA)
• 1-phase wide-range input from 85 V to 264 V AC or
110 V to 300 V DC
• Small mounting surface thanks to its slim design
• High efficiency across the entire load range: up to 28 %
energy savings in comparison with similar devices
• Low energy consumption during no-load operation or
stand-by: Energy savings of up to 53 % are possible
• Adjustable output voltage for compensating voltage drops
• Green LED for "Output voltage OK"
• Plug-in connecting terminals for pre-fabricated wiring and fast
electrical connection
• Wide temperature range from –20 to +70 °C
• Comprehensive certifications, such as UL, ATEX or GL
2/2
Siemens KT 10.1 · 2015
© Siemens AG 2015
SITOP compact
1-phase, 12 V DC
■ Overview
The single-phase SITOP compact are power supplies for the
lower performance range. Thanks to the extremely space-saving
slim design, they are especially suited to distributed applications in control boxes or in small control cabinets. The series is
characterized by low power losses throughout the entire load
range. The losses are extremely low even during idling, which
means they are perfectly suited for applications that are
frequently in stand-by mode. The SITOP PSU100C power
supplies have a wide-range input for AC and DC networks;
plug-in terminals facilitate the electrical connection.
Main product highlights
• 12 V DC, 2 A and 6.5 A
• 1-phase wide-range input from 85 V to 264 V AC or
110 V to 300 V DC
• Small mounting surface thanks to its slim design
• High efficiency across the entire load range.
• Low energy consumption during no-load operation or
stand-by
• Adjustable output voltage for compensating voltage drops
• Green LED for "12 V OK"
• Plug-in connecting terminals for pre-fabricated wiring and fast
electrical connection
• Wide temperature range from –20 to +70 °C
• Comprehensive certifications, such as UL, ATEX or GL
■ Technical specifications
Article No.
6EP1321-5BA00
6EP1322-5BA10
Product
SITOP PSU100C
SITOP PSU100C
Power supply, type
12 V/2 A
12 V/6.5 A
Input
1-phase AC or DC
1-phase AC or DC
Rated voltage value Vin rated
100 ... 230 V
100 ... 230 V
Voltage range AC
85 ... 264 V
85 ... 264 V
• for DC
110 ... 300 V
110 ... 300 V
Wide-range input
Yes
Yes
Overvoltage resistance
2.3 × Vin rated, 1.3 ms
2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min.
20 ms; at Vin = 230 V
20 ms; at Vin = 230 V
Rated line frequency
50 ... 60 Hz
50 ... 60 Hz
Rated line range
47 ... 63 Hz
47 ... 63 Hz
• at rated input voltage 100 V
0.63 A
1.6 A
• at rated input voltage 230 V
0.31 A
0.8 A
Switch-on current limiting (+25 °C),
max.
33 A
31 A
I²t, max.
1.2 A²·s
3 A²·s
Built-in incoming fuse
internal
internal
Protection in the mains power input
(IEC 60898)
Recommended miniature circuit breaker: from 16 A
characteristic B or from 10 A characteristic C
Recommended miniature circuit breaker: from 16 A
characteristic B or from 10 A characteristic C
Input
Input voltage
Input current
Siemens KT 10.1 · 2015
2/3
2
© Siemens AG 2015
SITOP compact
1-phase, 12 V DC
■ Technical specifications (continued)
2
Article No.
6EP1321-5BA00
6EP1322-5BA10
Product
SITOP PSU100C
SITOP PSU100C
Power supply, type
12 V/2 A
12 V/6.5 A
Output
Controlled, isolated DC voltage
Controlled, isolated DC voltage
Rated voltage Vout DC
12 V
12 V
Total tolerance, static ±
3%
3%
Residual ripple peak-peak, max.
200 mV
200 mV
Residual ripple peak-peak, typ.
40 mV
80 mV
Spikes peak-peak, max.
(bandwidth: 20 MHz)
300 mV
300 mV
Spikes peak-peak, typ.
(bandwidth: 20 MHz)
50 mV
80 mV
Adjustment range
10.5 ... 12.9 V
10.5 ... 12.9 V
Product function Output voltage
adjustable
Yes
Yes
Output voltage setting
via potentiometer
via potentiometer
Status display
Green LED for output voltage OK
Green LED for output voltage OK
On/off behavior
Overshoot of Vout approx. 5 %
Overshoot of Vout approx. 1 %
Startup delay, max.
0.6 s
1s
Voltage rise, typ.
10 ms
500 ms
Rated current value Iout rated
2A
6.5 A
Current range
0 ... 2 A
0 ... 6.5 A
• Note
+55 ... +70 °C: Derating 3%/K
+50 ... +70 °C: Derating 3.5%/K
Active power supplied typical
24 W
78 W
Parallel switching for enhanced
performance
Yes; Start-up with single nominal load only
Yes; Start-up with single nominal load only
Numbers of parallel switchable units
for enhanced performance
2
2
Efficiency at Vout rated, Iout rated,
approx.
82 %
86 %
Power loss at Vout rated, Iout rated,
approx.
5.8 W
12.5 W
Active power loss during no-load
operation maximum
0.75 W
0.75 W
Dynamic mains compensation
(Vin rated ±15 %), max.
0.1 %
0.1 %
Dynamic load smoothing
(Iout: 10/90/10 %), Uout ± typ.
3%
3%
Output
Efficiency
Closed-loop control
Load step setting time 10 to 90%, typ. 4 ms
3 ms
Load step setting time 90 to 10%, typ. 3 ms
3 ms
Protection and monitoring
Output overvoltage protection
Yes, according to EN 60950-1
Yes, according to EN 60950-1
Current limitation, typ.
2.4 A
7.2 A
Property of the output Short-circuit proof Yes
Yes
Short-circuit protection
Electronic shutdown, automatic restart
Electronic shutdown, automatic restart
Overload/short-circuit indicator
-
-
Primary/secondary isolation
Yes
Yes
Galvanic isolation
Safety extra-low output voltage Uout acc. to EN 60950-1
and EN 50178
Safety extra-low output voltage Uout acc. to EN 60950-1
and EN 50178
Protection class
Class I
Class I
• maximum
3.5 mA
3.5 mA
• typical
0.4 mA
0.4 mA
Safety
Leakage current
2/4
Siemens KT 10.1 · 2015
© Siemens AG 2015
SITOP compact
1-phase, 12 V DC
■ Technical specifications (continued)
Article No.
6EP1321-5BA00
6EP1322-5BA10
Product
SITOP PSU100C
SITOP PSU100C
Power supply, type
12 V/2 A
12 V/6.5 A
CE mark
Yes
Yes
UL/CSA approval
Yes
Yes
UL/cUL (CSA) approval
cULus-Listed (UL 508, CSA C22.2 No. 107.1), File
E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)
cULus-Listed (UL 508, CSA C22.2 No. 107.1), File
E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)
Explosion protection
ATEX (EX) II 3G Ex nA IIC T4; cCSAus (CSA C22.2 No. 213- ATEX (EX) II 3G Ex nA IIC T4; cCSAus (CSA C22.2 No. 213M1987, ANSI/ISA-12.12.01-2007) Class I, Div. 2, Group
M1987, ANSI/ISA-12.12.01-2007) Class I, Div. 2, Group
ABCD, T4
ABCD, T4
Certificate of suitability IECEx
No
No
Certificate of suitability NEC Class 2
No
No
FM approval
-
-
CB approval
Yes
Yes
Marine approval
GL, ABS
GL, ABS
Degree of protection (EN 60529)
IP20
IP20
Emitted interference
EN 55022 Class B
EN 55022 Class B
Supply harmonics limitation
not applicable
EN 61000-3-2
Noise immunity
EN 61000-6-2
EN 61000-6-2
-20 ... +70 °C
-20 ... +70 °C
with natural convection
with natural convection
• during transport
-40 ... +85 °C
-40 ... +85 °C
• during storage
-40 ... +85 °C
-40 ... +85 °C
Humidity class according to
EN 60721
Climate class 3K3, no condensation
Climate class 3K3, no condensation
screw-type terminals
screw-type terminals
2
EMC
Operating data
Ambient temperature
• during operation
- Note
Mechanics
Connection technology
Connections
• Supply input
L, N, PE: Removable screw terminal, each for 1 x 0.5 ... 2.5 mm² L, N, PE: Removable screw terminal, each for 1 x 0.5 ... 2.5 mm²
• Output
+: 1 screw terminal for 0.5 ... 2.5 mm²;
-: 2 screw terminals for 0.5 ... 2.5 mm²
+: 1 screw terminal for 0.5 ... 2.5 mm²;
-: 2 screw terminals for 0.5 ... 2.5 mm²
• Auxiliary
-
-
Width of the enclosure
30 mm
52.5 mm
Height of the enclosure
80 mm
80 mm
Depth of the enclosure
100 mm
100 mm
Weight, approx.
0.12 kg
0.32 kg
Product property of the enclosure
housing for side-by-side mounting
Yes
Yes
Installation
Snaps onto DIN rail EN 60715 35x7.5/15
Snaps onto DIN rail EN 60715 35x7.5/15
Electrical accessories
Removable spring-type terminal 6EP1971-5BA00
Removable spring-type terminal 6EP1971-5BA00
Other information
Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)
Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)
■ Ordering data
SITOP PSU100C 1-phase,
12 V DC/2 A
Article No.
6EP1321-5BA00
Stabilized power supply
Input: 100 ... 230 V AC
Output: 12 V DC/2 A
SITOP PSU100C 1-phase,
12 V DC/6.5 A
■ Accessories
SITOP Power PSU100C
accessories
Article No.
6EP1971-5BA00
Removable spring-loaded terminal,
100 units, for SITOP PSU100C
6EP1322-5BA10
Stabilized power supply
Input: 100 … 230 V AC
Output: 12 V DC/6.5 A
Siemens KT 10.1 · 2015
2/5
© Siemens AG 2015
SITOP compact
1-phase, 24 V DC
■ Overview
The single-phase SITOP compact are power supplies for the
lower performance range. Thanks to the extremely space-saving
slim design, they are especially suited to distributed applications in control boxes or in small control cabinets. The series is
characterized by low power losses throughout the entire load
range. The losses are extremely low even during idling, which
means they are perfectly suited for applications that are
frequently in stand-by mode. The SITOP PSU100C power
supplies have a wide-range input for AC and DC networks;
plug-in terminals facilitate the electrical connection.
2
To further increase the 24 V availability, the SITOP compact
power supplies can be combined with DC UPS, redundancy
and selectivity modules.
Main product highlights
• 24 V DC/ 0.6 A, 1.3 A, 2.5 A and 4 A
• 24 V DC/3.7 A for the supply of NEC class 2 circuits with
limited output power (100 VA)
• 1-phase wide-range input from 85 V to 264 V AC or
110 V to 300 V DC
• Small mounting surface thanks to its slim design
• High efficiency across the entire load range.
• Low energy consumption during no-load operation or
stand-by
• Adjustable output voltage for compensating voltage drops
(starting at 1.3 A)
• Green LED for "24 V OK"
• Plug-in connecting terminals for pre-fabricated wiring and fast
electrical connection
• Wide temperature range from –20 to +70 °C
• Comprehensive certifications, such as UL, ATEX or GL
■ Technical specifications
Article No.
6EP1331-5BA00
6EP1331-5BA10
6EP1332-5BA00
Product
SITOP PSU100C
SITOP PSU100C
SITOP PSU100C
Power supply, type
24 V/0.6 A
24 V/1.3 A
24 V/2.5 A
Input
1-phase AC or DC
1-phase AC or DC
1-phase AC or DC
Rated voltage value Vin rated
100 ... 230 V
100 ... 230 V
100 ... 230 V
Voltage range AC
85 ... 264 V
85 ... 264 V
85 ... 264 V
• for DC
110 ... 300 V
110 ... 300 V
110 ... 300 V
Wide-range input
Yes
Yes
Yes
Overvoltage resistance
2.3 × Vin rated, 1.3 ms
2.3 × Vin rated, 1.3 ms
2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min.
20 ms; at Vin = 230 V
20 ms; at Vin = 230 V
20 ms; at Vin = 230 V
Rated line frequency
50 ... 60 Hz
50 ... 60 Hz
50 ... 60 Hz
Rated line range
47 ... 63 Hz
47 ... 63 Hz
47 ... 63 Hz
• at rated input voltage 100 V
0.28 A
0.63 A
1.21 A
• at rated input voltage 230 V
0.18 A
0.31 A
0.67 A
Switch-on current limiting (+25 °C),
max.
28 A
34 A
31 A
I²t, max.
0.7 A²·s
1.2 A²·s
2.4 A²·s
Built-in incoming fuse
internal
internal
internal
Protection in the mains power input
(IEC 60898)
Recommended miniature circuit
breaker: from 16 A characteristic B or
from 10 A characteristic C
Recommended miniature circuit
breaker: from 16 A characteristic B or
from 10 A characteristic C
Recommended miniature circuit
breaker: from 16 A characteristic B or
from 10 A characteristic C
Input
Input voltage
Input current
2/6
Siemens KT 10.1 · 2015
© Siemens AG 2015
SITOP compact
1-phase, 24 V DC
■ Technical specifications (continued)
Article No.
6EP1331-5BA00
6EP1331-5BA10
6EP1332-5BA00
Product
SITOP PSU100C
SITOP PSU100C
SITOP PSU100C
Power supply, type
24 V/0.6 A
24 V/1.3 A
24 V/2.5 A
Output
Controlled, isolated DC voltage
Controlled, isolated DC voltage
Controlled, isolated DC voltage
Rated voltage Vout DC
24 V
24 V
24 V
Total tolerance, static ±
3%
3%
3%
Static mains compensation, approx.
0.1 %
0.1 %
0.1 %
Static load balancing, approx.
0.2 %
0.2 %
0.2 %
Residual ripple peak-peak, max.
200 mV
200 mV
200 mV
Residual ripple peak-peak, typ.
40 mV
25 mV
55 mV
Spikes peak-peak, max.
(bandwidth: 20 MHz)
300 mV
300 mV
300 mV
Spikes peak-peak, typ.
(bandwidth: 20 MHz)
20 mV
20 mV
50 mV
Adjustment range
-
22.2 ... 26.4 V
22.2 ... 26.4 V
Product function Output voltage
adjustable
No
Yes
Yes
Output voltage setting
-
via potentiometer
via potentiometer
Status display
Green LED for output voltage OK
Green LED for output voltage OK
Green LED for output voltage OK
On/off behavior
Overshoot of Vout approx. 5 %
Overshoot of Vout approx. 5 %
Overshoot of Vout approx. 1 %
Startup delay, max.
1s
0.6 s
0.7 s
Voltage rise, typ.
25 ms
90 ms
100 ms
Rated current value Iout rated
0.6 A
1.3 A
2.5 A
Current range
0 ... 0.6 A
0 ... 1.3 A
0 ... 2.5 A
• Note
+55 ... +70 °C: Derating 3%/K
+55 ... +70 °C: Derating 3%/K
+55 ... +70 °C: Derating 3,5%/K
Active power supplied typical
14 W
30 W
60 W
• at short-circuit during operation
typical
1A
3.1 A
-
Parallel switching for enhanced
performance
No
Yes; Start-up with single nominal load
only
Yes; Start-up with single nominal load
only
Numbers of parallel switchable units
for enhanced performance
-
2
2
Efficiency at Vout rated, Iout rated,
approx.
82 %
86 %
87 %
Power loss at Vout rated, Iout rated,
approx.
2.6 W
4.5 W
9W
Active power loss during no-load
operation maximum
0.75 W
0.75 W
0.75 W
Dynamic mains compensation
(Vin rated ±15 %), max.
0.1 %
0.1 %
0.1 %
Dynamic load smoothing
(Iout: 10/90/10 %), Uout ± typ.
3%
3%
3%
Load step setting time 10 to 90%, typ. 3 ms
5 ms
4 ms
Load step setting time 90 to 10%, typ. 3 ms
5 ms
4 ms
2
Output
Short-term overload current
Efficiency
Closed-loop control
Protection and monitoring
Output overvoltage protection
Yes, according to EN 60950-1
Yes, according to EN 60950-1
Yes, according to EN 60950-1
Current limitation, typ.
0.7 A
1.4 A
3A
Property of the output Short-circuit
proof
Yes
Yes
Yes
Short-circuit protection
Electronic shutdown, automatic restart Electronic shutdown, automatic restart Electronic shutdown, automatic restart
Overload/short-circuit indicator
-
-
-
Siemens KT 10.1 · 2015
2/7
© Siemens AG 2015
SITOP compact
1-phase, 24 V DC
■ Technical specifications (continued)
2
Article No.
6EP1331-5BA00
6EP1331-5BA10
6EP1332-5BA00
Product
SITOP PSU100C
SITOP PSU100C
SITOP PSU100C
Power supply, type
24 V/0.6 A
24 V/1.3 A
24 V/2.5 A
Primary/secondary isolation
Yes
Yes
Yes
Galvanic isolation
Safety extra-low output voltage Uout
acc. to EN 60950-1 and EN 50178
Safety extra-low output voltage Uout
acc. to EN 60950-1 and EN 50178
Safety extra-low output voltage Uout
acc. to EN 60950-1 and EN 50178
Protection class
Class I
Class I
Class I
• maximum
3.5 mA
3.5 mA
3.5 mA
• typical
0.4 mA
0.4 mA
0.4 mA
CE mark
Yes
Yes
Yes
UL/CSA approval
Yes
Yes
Yes
UL/cUL (CSA) approval
cULus-Listed (UL 508, CSA C22.2 No.
107.1), File E197259; cURus-Recognized (UL 60950, CSA C22.2 No.
60950), File E151273, NEC class 2
(acc. to UL 1310)
cULus-Listed (UL 508, CSA C22.2 No.
107.1), File E197259; cURus-Recognized (UL 60950, CSA C22.2 No.
60950), File E151273, NEC class 2
(acc. to UL 1310)
cULus-Listed (UL 508, CSA C22.2 No.
107.1), File E197259; cURus-Recognized (UL 60950, CSA C22.2 No.
60950), File E151273, NEC class 2
(acc. to UL 1310)
Explosion protection
ATEX (EX) II 3G Ex nA IIC T4; cCSAus
(CSA C22.2 No. 213-M1987, ANSI/ISA12.12.01-2007) Class I, Div. 2, Group
ABCD, T4
ATEX (EX) II 3G Ex nA IIC T4; cCSAus
(CSA C22.2 No. 213-M1987, ANSI/ISA12.12.01-2007) Class I, Div. 2, Group
ABCD, T4
ATEX (EX) II 3G Ex nA IIC T4; cCSAus
(CSA C22.2 No. 213-M1987, ANSI/ISA12.12.01-2007) Class I, Div. 2, Group
ABCD, T4
Certificate of suitability IECEx
No
No
No
Certificate of suitability NEC Class 2
Yes
Yes
Yes
FM approval
-
-
-
CB approval
Yes
Yes
Yes
Marine approval
GL, ABS
GL, ABS
GL, ABS
Degree of protection (EN 60529)
IP20
IP20
IP20
Emitted interference
EN 55022 Class B
EN 55022 Class B
EN 55022 Class B
Supply harmonics limitation
not applicable
not applicable
not applicable
Noise immunity
EN 61000-6-2
EN 61000-6-2
EN 61000-6-2
-20 ... +70 °C
-20 ... +70 °C
-20 ... +70 °C
with natural convection
with natural convection
with natural convection
• during transport
-40 ... +85 °C
-40 ... +85 °C
-40 ... +85 °C
• during storage
-40 ... +85 °C
-40 ... +85 °C
-40 ... +85 °C
Climate class 3K3, no condensation
Climate class 3K3, no condensation
screw-type terminals
screw-type terminals
screw-type terminals
• Supply input
L, N, PE: Removable screw terminal,
each for 1 x 0.5 ... 2.5 mm²
L, N, PE: Removable screw terminal,
each for 1 x 0.5 ... 2.5 mm²
L, N, PE: Removable screw terminal,
each for 1 x 0.5 ... 2.5 mm²
• Output
+: 1 screw terminal for 0.5 ... 2.5 mm²; +: 1 screw terminal for 0.5 ... 2.5 mm²; +: 1 screw terminal for 0.5 ... 2.5 mm²;
-: 2 screw terminals for 0.5 ... 2.5 mm² -: 2 screw terminals for 0.5 ... 2.5 mm² -: 2 screw terminals for 0.5 ... 2.5 mm²
• Auxiliary
-
-
-
Width of the enclosure
22.5 mm
30 mm
45 mm
Height of the enclosure
80 mm
80 mm
80 mm
Depth of the enclosure
100 mm
100 mm
100 mm
Weight, approx.
0.12 kg
0.17 kg
0.22 kg
Product property of the enclosure
housing for side-by-side mounting
Yes
Yes
Yes
Installation
Snaps onto DIN rail EN 60715 35x7.5/15 Snaps onto DIN rail EN 60715 35x7.5/15 Snaps onto DIN rail EN 60715 35x7.5/15
Electrical accessories
Removable spring-type terminal
6EP1971-5BA00
Removable spring-type terminal
6EP1971-5BA00
Removable spring-type terminal
6EP1971-5BA00
Other information
Specifications at rated input voltage
and ambient temperature +25 °C
(unless otherwise specified)
Specifications at rated input voltage
and ambient temperature +25 °C
(unless otherwise specified)
Specifications at rated input voltage
and ambient temperature +25 °C
(unless otherwise specified)
Safety
Leakage current
EMC
Operating data
Ambient temperature
• during operation
- Note
Humidity class according to EN 60721 Climate class 3K3, no condensation
Mechanics
Connection technology
Connections
2/8
Siemens KT 10.1 · 2015
© Siemens AG 2015
SITOP compact
1-phase, 24 V DC
■ Technical specifications (continued)
Article No.
6EP1332-5BA20
6EP1332-5BA10
Product
SITOP PSU100C
SITOP PSU100C
Power supply, type
24 V/3.7 A
24 V/4 A
Input
1-phase AC or DC
1-phase AC or DC
Rated voltage value Vin rated
100 ... 230 V
100 ... 230 V
Voltage range AC
85 ... 264 V
85 ... 264 V
• for DC
110 ... 300 V
110 ... 300 V
Wide-range input
Yes
Yes
Overvoltage resistance
2.3 × Vin rated, 1.3 ms
2.3 × Vin rated, 1.3 ms
Mains buffering at Iout rated, min.
20 ms; at Vin = 230 V
20 ms; at Vin = 230 V
Rated line frequency
50 ... 60 Hz
50 ... 60 Hz
Rated line range
47 ... 63 Hz
47 ... 63 Hz
• at rated input voltage 100 V
1.88 A
2.25 A
• at rated input voltage 230 V
0.95 A
1.15 A
Switch-on current limiting (+25 °C),
max.
30 A
34 A
I²t, max.
3 A²·s
3 A²·s
Built-in incoming fuse
internal
internal
Protection in the mains power input
(IEC 60898)
Recommended miniature circuit breaker: from 16 A
characteristic B or from 10 A characteristic C
Recommended miniature circuit breaker: from 16 A
characteristic B or from 10 A characteristic C
Output
Controlled, isolated DC voltage
Controlled, isolated DC voltage
Rated voltage Vout DC
24 V
24 V
Total tolerance, static ±
3%
3%
Residual ripple peak-peak, max.
200 mV
200 mV
Residual ripple peak-peak, typ.
90 mV
80 mV
Spikes peak-peak, max.
(bandwidth: 20 MHz)
300 mV
300 mV
Spikes peak-peak, typ.
(bandwidth: 20 MHz)
60 mV
80 mV
Adjustment range
-
22.2 ... 26.4 V
Product function Output voltage
adjustable
No
Yes
Output voltage setting
-
via potentiometer
Status display
Green LED for output voltage OK
Green LED for output voltage OK
On/off behavior
Overshoot of Vout approx. 1 %
Overshoot of Vout approx. 1 %
Startup delay, max.
1.5 s
1.5 s
Voltage rise, typ.
500 ms
400 ms
Rated current value Iout rated
3.7 A
4A
Current range
0 ... 3.7 A
0 ... 4 A
• Note
+55 ... +70 °C: Derating 3,5%/K
+55 ... +70 °C: Derating 3,5%/K
Active power supplied typical
89 W
96 W
Parallel switching for enhanced
performance
No
Yes; Start-up with single nominal load only
Numbers of parallel switchable units
for enhanced performance
-
2
2
Input
Input voltage
Input current
Output
Siemens KT 10.1 · 2015
2/9
© Siemens AG 2015
SITOP compact
1-phase, 24 V DC
■ Technical specifications (continued)
2
Article No.
6EP1332-5BA20
6EP1332-5BA10
Product
SITOP PSU100C
SITOP PSU100C
Power supply, type
24 V/3.7 A
24 V/4 A
Efficiency at Vout rated, Iout rated,
approx.
87 %
88 %
Power loss at Vout rated, Iout rated,
approx.
14 W
13 W
Active power loss during no-load
operation maximum
0.75 W
0.75 W
Dynamic mains compensation
(Vin rated ±15 %), max.
0.1 %
0.1 %
Dynamic load smoothing
(Iout: 10/90/10 %), Uout ± typ.
3%
3%
Efficiency
Closed-loop control
Load step setting time 10 to 90%, typ. 4 ms
4 ms
Load step setting time 90 to 10%, typ. 4 ms
4 ms
Protection and monitoring
Output overvoltage protection
Yes, according to EN 60950-1
Yes, according to EN 60950-1
Current limitation, typ.
4A
4.8 A
Property of the output Short-circuit
proof
Yes
Yes
Short-circuit protection
Electronic shutdown, automatic restart
Electronic shutdown, automatic restart
Overload/short-circuit indicator
-
-
Primary/secondary isolation
Yes
Yes
Galvanic isolation
Safety extra-low output voltage Uout acc. to EN 60950-1
and EN 50178
Safety extra-low output voltage Uout acc. to EN 60950-1
and EN 50178
Protection class
Class I
Class I
• maximum
3.5 mA
3.5 mA
• typical
0.4 mA
0.4 mA
CE mark
Yes
Yes
UL/CSA approval
Yes
Yes
UL/cUL (CSA) approval
cULus-Listed (UL 508, CSA C22.2 No. 107.1), File
E197259; cURus-Recognized (UL 60950, CSA C22.2
No. 60950), File E151273, NEC class 2 (acc. to UL 1310)
cULus-Listed (UL 508, CSA C22.2 No. 107.1), File
E197259; cCSAus (CSA C22.2 No. 60950-1, UL 60950-1)
Explosion protection
ATEX (EX) II 3G Ex nA IIC T4; cCSAus (CSA C22.2
No. 213-M1987, ANSI/ISA-12.12.01-2007) Class I, Div. 2,
Group ABCD, T4
ATEX (EX) II 3G Ex nA IIC T4; cCSAus (CSA C22.2
No. 213-M1987, ANSI/ISA-12.12.01-2007) Class I, Div. 2,
Group ABCD, T4
Certificate of suitability IECEx
No
No
Certificate of suitability NEC Class 2
Yes
No
FM approval
-
-
CB approval
Yes
Yes
Marine approval
GL, ABS
GL, ABS
Degree of protection (EN 60529)
IP20
IP20
Safety
Leakage current
2/10
Siemens KT 10.1 · 2015
© Siemens AG 2015
SITOP compact
1-phase, 24 V DC
■ Technical specifications (continued)
Article No.
6EP1332-5BA20
6EP1332-5BA10
Product
SITOP PSU100C
SITOP PSU100C
Power supply, type
24 V/3.7 A
24 V/4 A
Emitted interference
EN 55022 Class B
EN 55022 Class B
Supply harmonics limitation
EN 61000-3-2
EN 61000-3-2
Noise immunity
EN 61000-6-2
EN 61000-6-2
-20 ... +70 °C
-20 ... +70 °C
with natural convection
with natural convection
• during transport
-40 ... +85 °C
-40 ... +85 °C
• during storage
-40 ... +85 °C
-40 ... +85 °C
Humidity class according to
EN 60721
Climate class 3K3, no condensation
Climate class 3K3, no condensation
screw-type terminals
screw-type terminals
• Supply input
L, N, PE: Removable screw terminal, each for
1 x 0.5 ... 2.5 mm²
L, N, PE: Removable screw terminal, each for
1 x 0.5 ... 2.5 mm²
• Output
+: 1 screw terminal for 0.5 ... 2.5 mm²;
-: 2 screw terminals for 0.5 ... 2.5 mm²
+: 1 screw terminal for 0.5 ... 2.5 mm²;
-: 2 screw terminals for 0.5 ... 2.5 mm²
• Auxiliary
-
-
Width of the enclosure
52.5 mm
52.5 mm
Height of the enclosure
80 mm
80 mm
Depth of the enclosure
100 mm
100 mm
Weight, approx.
0.32 kg
0.32 kg
Product property of the enclosure
housing for side-by-side mounting
Yes
Yes
Installation
Snaps onto DIN rail EN 60715 35x7.5/15
Snaps onto DIN rail EN 60715 35x7.5/15
Electrical accessories
Removable spring-type terminal 6EP1971-5BA00
Removable spring-type terminal 6EP1971-5BA00
Other information
Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)
Specifications at rated input voltage and ambient temperature +25 °C (unless otherwise specified)
2
EMC
Operating data
Ambient temperature
• during operation
- Note
Mechanics
Connection technology
Connections
Siemens KT 10.1 · 2015
2/11
© Siemens AG 2015
SITOP compact
1-phase, 24 V DC
■ Ordering data
2
SITOP PSU100C 1-phase,
24 V DC/0.6 A
Article No.
6EP1331-5BA00
Stabilized power supply
Input: 100 … 230 V AC
Output: 24V DC/0.6 A
SITOP PSU100C 1-phase,
24 V DC/1.3 A
6EP1331-5BA10
6EP1332-5BA00
6EP1332-5BA20
Stabilized power supply
Input: 100 … 230 V AC
(110 … 300 V AC)
Output: 24 V DC/3.7 A
limited output power NEC Class 2
SITOP PSU100C 1-phase,
24 V DC/4 A
6EP1962-2BA00
Input/output: 24 V DC/NEC Class 2
suitable for decoupling two SITOP
power supplies output power limited
< 100 VA
6EP1964-2BA00
Input/output: 24 V DC/10 A
suitable for decoupling two SITOP
power supplies with a maximum of
5 A output current
4-channel selectivity module
Input: 24 V DC
Output: 24 V DC/3A per each channel
output current adjustable 0.5 … 3 A
• With common alarm signal
6EP1961-2BA11
• With single-channel signaling
6EP1961-2BA31
SITOP Power PSU100C
accessories
6EP1332-5BA10
Stabilized power supply
Input: 120 … 230 V AC
Output: 24 V DC/4 A
2/12
Article No.
SITOP PSE200U 3 A
selectivity module
Stabilized power supply
Input: 100 … 230 V AC
Output: 24 V DC/2.5 A
SITOP PSU100C 1-phase,
24 V DC/3.7 A
SITOP PSE202U
redundancy module
SITOP PSE202U
redundancy module
Stabilized power supply
Input: 120 … 230 V AC
Output: 24 V DC/1.3 A
SITOP PSU100C 1-phase,
24 V DC/2.5 A
■ Accessories
Siemens KT 10.1 · 2015
Removable spring-loaded terminal,
100 units, for SITOP PSU100C
6EP1971-5BA00