TRANSDUCTION
USER’S MANUAL
Version 1.0
06/12/12
TR-7 INDUSTRIAL PANEL/RACK MOUNT PC
WITH 1" TFT LCD TOUCH SCREEN
WITH INTEL CORE i7 / i5 / i3 PROCESSORS
23-5155 Spectrum Way, Mississauga, ON, Canada L4W 5A1
TEL: 1-800-268-0427, 905-625-1907
F AX: 905-625-0531
Email: sales@transduction.com
TABLE OF CONTENTS
Table of Contents
Important Information .................................................................................................................................. 1
Recommended Use ....................................................................................................................................... 2
Introduction ................................................................................................................................................... 3
Contents ...................................................................................................................................................... 4
TR-7190 Specifications ........................................................................................................................... 5-6
TR-6S2 Backplane ....................................................................................................................................... 6
Touch Screen ........................................................................................................................................ 7-15
TR-999 SBC Introduction ............................................................................................................................. 17
Product Description ................................................................................................................................. 18
TR-999 Specifications ............................................................................................................................... 19
Board Dimensions .................................................................................................................................... 20
Installations ................................................................................................................................................. 21
Installing the CPU ..................................................................................................................................... 22
Installing the Memory .............................................................................................................................. 23
Setting the Jumpers ........................................................................................................................... 24-28
Connectors on TR-999 ........................................................................................................................ 29-37
BIOS Setup ................................................................................................................................................... 39
BIOS Introduction ..................................................................................................................................... 40
BIOS Setup .......................................................................................................................................... 40-41
Advanced Settings .............................................................................................................................. 42-53
Chipset Settings .................................................................................................................................. 54-57
Boot Settings ............................................................................................................................................ 58
Security Settings ....................................................................................................................................... 59
Save & Exit Settings ............................................................................................................................ 60-61
i
TR-7190 User Manual
TABLE OF CONTENTS
Drivers Installation ...................................................................................................................................... 63
Intel Chipset Software Installation Utility ................................................................................................ 64
VGA Drivers Installation ........................................................................................................................... 65
Realtek HD Audio Driver Installation ....................................................................................................... 66
LAN Drivers Installation ...................................................................................................................... 67-68
Intel Management Engine Interface .................................................................................................. 69-70
Appendix ...................................................................................................................................................... 71
I/O Port Address Map .............................................................................................................................. 71
Interrupt Request Line (IRQ) .................................................................................................................... 72
Watchdog Timer Configuration .......................................................................................................... 73-75
TR-7190 Mechanical Drawings ............................................................................................................ 76-91
ii
TR-7190 User Manual
IMPORTANT INFORMATION
The information in this document is subject to change without notice.
All relevant issues have been considered in the preparation of this document.
Should you notice an omission or any questionable item in this document, please
feel free to notify Transduction. Regardless of the foregoing statement,
Transduction assumes no responsibility for any errors that may appear in this
document nor for results obtained by the user as a result of using this product.
Copyright © 2012 Transduction. All rights reserved.
This document is protected by copyright. No part of this document may be
reproduced, copied or translated in any form or means without prior written
permission from Transduction. All other trademarks, brand and product names
are the property of their respective owners.
Return policy
Products returned for repair must be accompanied by a Return Material
Authorization (RMA) number, obtained from Transduction prior to return.
Freight on all returned items must be prepaid by the customer. The customer is
responsible for any loss or damage caused by the carrier in transit. To obtain an
RMA number, call us at 905-625-1907. We will need the following information:
•
Return company address and contract
•
Model name, model number and serial number
•
Description of the failure
Mark the RMA number clearly on the outside of each box, include a failure
report
and return the product to:
Transduction
5155 – 23 Spectrum Way
Mississauga ON Canada L4W 5A1
Attn: RMA Department
1
TR-7190 User Manual
RECOMMENDED USE
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE
THE FOLLOWING WHEN SETTING UP
AND USING THE TR-7ϭϵϬ:
•
•
•
•
•
•
•
•
•
DO NOT OPEN THE MONITOR. There are no user serviceable parts inside
and opening or removing covers may expose you to dangerous shock hazards
or other risks. Refer all servicing to qualified service personnel.
Do not spill any liquids into the cabinet or use your monitor near water.
Do not insert objects of any kind into the cabinet slots, as they may touch
dangerous voltage points, which can be harmful or fatal or may cause electric
shock, fire or equipment failure.
Do not place any heavy objects on the power cord. Damage to the cord may
cause shock or fire.
Do not place this product on a sloping or unstable cart, stand or table, as the
monitor may fall, causing serious damage to the monitor.
When operating the TR-7ϭϵϬ with its AC 125-240V power supply, use a power
supply cord that matches the power supply voltage of the AC power outlet
being used. The power supply cord you use must have been approved by and
comply with the safety standards of your country. (Type H05VV-F should be
used in Europe)
In UK, use a BS-approved power cord with molded plug having a black (5A)
fuse installed for use with this monitor. If a power cord is not supplied with
this monitor, please contact your supplier.
Do not place any objects onto the monitor and do not use outdoors.
The inside of the fluorescent tube located within the LCD monitor contains
mercury. Please follow the bylaws or rules of your municipality to dispose of
the tube properly.
Immediately unplug your unit from the power source and refer servicing to qualified
service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the unit.
• If the unit has been exposed to rain or water.
• If the unit has been dropped or the cabinet damaged.
• If the unit does not operate normally by following operating instructions.
• Do not bend power cord.
• Do not use in high temperatured, humid, dusty, or oily areas.
• If glass is broken, handle with care.
• Do not cover vents on unit.
• If monitor or glass is broken, do not come in contact with the liquid crystal
and handle with care.
• Allow adequate ventilation around the unit so that heat can properly
dissipate. Do not block ventilated openings or place near a radiator or other
heat sources.
• Handle with care when transporting. Save packaging for transporting.
2
TR-7190 User Manual
INTRODUCTION
Introduction
This chapter is designed to give an overview of TR-7190 industrial PC.
The topics covered in this chapter are as follows:
Contents ......................................................................................................... 4
TR-7190 Specifications ............................................................................... 5-6
TR-6S2 Backplane............................................................................... 6
Touch Screen .................................................................................................7-15
3
TR-7190 User Manual
INTRODUCTION
Contents
Your new TR-7ϭϵϬ box* should contain the following:
•
TR-7ϭϵϬ PC/LCD
•
Power Cord
•
User’s Manual
•
CD-ROM with drivers
TR-7190 Panel/RackMount PC
User’s Manual
Driver CD
*Remember to save your original box and packing material to transport or ship the monitor.
4
TR-7190 User Manual
INTRODUCTION
TR-7190 Specifications
Model TR-7190 Industrial Panel Mount and Rack Mount
Computer with Intel Core 1-series Processor 19”
LCD Touch Screen
Processor
LCD Display
Memory
Drive Bay
Intel Socket LGA1155 for Core i-series, i7, i5 and
i3 processors up to 3.4GHz with 1066/1333MHz
FSB with 62CFM PWM air fan
Resolution - 1280 x 1024 (XGA)
Backlight MTBF 150,000 hours
Brightness - 300cd/m ²
Contrast Ratio - 700:1
Resistive or capacitive touch screen
2 x 240 pin DIMM sockets, up to 16GB DDR3
memory, high temperature version
2 x 3.5” HDD (RAID 1 Ok) or Flash SSD
1 x 5.25” SATA CD-DVD-R/W
Expansion Slots (TR-6S2 Backplane) 3 x PCI, 1 x PCIe x4 and 1 x PCIe x16
Display Intel Graphic Engine interface, DB15 SVGA
connector
Ethernet
Solid State Disk
I/O
Watchdog Timer
2 x Intel 82579V/82583V on board for Dual
Gigabit LAN
High speed flash SATA SSD 64GB ~ 512GB with
bad block auto-correction
2 x Serial RS-232
3 x USB 2.0
2 x RJ-45 LAN
1 x LPT
PS/2 keyboard/mouse connectors
Generates system reset; 256 levels
Cooling 1 x CPU cooling fan connector near CPU socket
1 x system cooling fan connectors for chassis or
power supply cooling
Power
Output rating - 300W
Input Voltage - 100 ~ 240VAC @ 47/63Hz
Optional DC input power - 12V, 24V, 48V, 125V
and 250V
MTBF 80,000 hours
Electrical Safety Approval
System Monitor
Monitor processor temperature, system/CPU
temperature and voltage status, also processor
and system air fans
Operating Temperature
5
0º ~ 50ºC (32º ~ 122ºF) with hard drive
0º ~ 60ºC (32º ~ 140ºF) for 2 hours with SSD
Relative Humidity: 5 ~ 95%
TR-7190 User Manual
INTRODUCTION
Dimensions 17.75” (W) x 15.25” (H) x 6.4” (D) (8.00” (D)
behind front panel)
Rack mount version is 8U high
N.W. 32 lbs, G.W. 37 lbs, CUFT. 6
Chassis Colour Black, OEM colour optional
Warranty 3 years or 10% initial cost for 5 years
Additional Options 9U rack mount version
Rear access Floppy/CD option
Wall mounting bracket
High speed flash SATA SSD 64 ~ 512GB with bad
block auto-correction
SATA RAID 1 option up to 1TB
6 additional USB ports
BNC IRIG A/B time sync option
Safety glass in place of touch screen
TR-6S2 Backplane
VORW3,&0*EDFNSODQHZLWK[3&,[3&,H[[3&,H[DQG[6%&VORWV
6
TR-7190 User Manual
INTRODUCTION
Touch Screen
USB Controller Driver Installation
All Windows drivers are included on the Transduction TR-7ϭϵϬ 5-wire
Touchscreen Drivers CD along with Troubleshooting.
NOTE: For Win XP and 2000 you MUST logon with administrator’s
password.
TouchKit software on the driver CD has the required drivers and the
utility for toggling between left and right mouse buttons and configuration
support. These will all be installed when Setup.exe is run from the CD.
For Windows 2000/XP
When the New Hardware Found message comes up, choose Cancel.
Run the Setup.exe program from the driver CD.
Please note that the touch screen controller in the TR-7190 is USB and
follow the prompts accordingly.
Windows will copy the files to your hard drive and setup will be complete.
(Windows XP will give a warning message about the TouchKit Controller
certification, press Continue anyway.)
Please reboot your computer.
Windows will now find the device automatically and it will be listed in the
Device Manager as: TouchKit USB Controller.
TouchKit Software
There are five property pages:
1. GENERAL: Language selection, add/remove devices, 4-point
Calibration, Draw Test and Advanced
4 pts Cal
Choose to calibrate your screen by touching the blinking
symbol on the panel until you get a beep or it stops blinking
7
TR-7190 User Manual
INTRODUCTION
Draw Test
Test the drawing position in relation to the display screen to verify
panel linearity, calibration capability and drawing line quality.
Advanced
A 25 Point calibration utility for the touch sensor.
Press Clear to clear previous calibration records.
Press 25 pts Cal to do 25 point calibration by touching the
blinking symbol on the panel until you get a beep or it stops
blinking. After calibration, the new record will overwrite the old one.
2. SETTING: Sound, Mouse Mode and Double Click Adjustment
Sound
8
TR-7190 User Manual
INTRODUCTION
No Sound
Choose to make no sound when panel is touched.
Touch Down
Beep will sound when panel is touched.
Lift Up
The system will not make any sound until finger leaves the
touch panel.
Frequency
Sound frequency, drag the cursor from left to right = low to high.
Duration
Sound duration, drag the cursor from left to right = short to long.
Mouse Mode
The Mouse Mode provides users
different operating options.
Mouse Button
Click it to show/hide Touch Tray on the right bottom corner of the
desktop.
Users can choose show or hide Touch Tray from the mouse icon in the
taskbar.
9
TR-7190 User Manual
INTRODUCTION
Change right/left button by clicking the upper small rectangular box of
Touch Tray.
Blue area indicates which button has been selected.
Shutdown utility
Click on shutdown utility in the task bar
Shutdown utility dialog
There are five modes in shutdown utility:
[Standby] to enter standby mode that saves power consumption.
[Shutdown] to turn off PC.
[Reboot] to restart PC.
[Cancel] to escape from the Shutdown utility dialog.
[Exit] to disable the Shutdown utility.
Please note that Windows NT does not support this function.
Mouse Mode
There are three mouse modes:
[Normal Mode]
Provides all the mouse functions, including the dragging function.
[Click on Touch]
Click action is executed as soon as panel is touched.
[Click on Release]
Click action will not be executed until finger leaves the panel.
Option
Touchkit provides an option for advanced Mouse Emulation setting.
When the Option button is pressed, a setting property sheet will pop up.
Support Constant Touch and Support Auto Right Button check boxes
are shown in the property sheet to
enable/disable constant touch and Auto right button support.
10
TR-7190 User Manual
INTRODUCTION
Constant Touch
Enable Constant Touch to force driver to stop reporting touch
points when movement is slight. You will see a stabilized cursor
instead of a chattering cursor when users touch the same point.
Eliminates unwanted noise.
Auto Right Button
Enable Auto Right Button to force driver to report a right click
mouse event to OS when users lift up from a constant touch.
You no longer need to touch the right button in the touchtray to
activate a right click. This makes it easier to right click.
Cursor Visibility
Cursor visibility function allows the cursor to be hidden.
Go to Start / Control Panel / Mouse / Pointers / Scheme, and
choose TouchKit Hide Cursor. Press [Apply] to make the
setting change, and press [OK] to escape the property page.
Double Click Adjustment
11
TR-7190 User Manual
INTRODUCTION
Double Click Speed
Double Click Speed is the double click response time for the
Windows system. Users can adjust the speed for easy double
click by touch panel.
Double Click Area
Each individual touch has its own touch tolerance. If the Double
Click Area is set to <Smaller>, the panel will be very sensitive
about micro-movements when you want to fix on a point. If set
to <Larger>, larger touch point movement is tolerated when you
want to point at a fixed position.
3. EDGE COEFFICIENT: Edge compensation for Top, Bottom, Left,
Right, X Axis and Y Axis
If it is difficult to touch items at the edges of the touch panel, you can
adjust the edges of the screen image.
Top
If you set the Edge to <Smaller>, TouchKit will reduce the
horizontal position of the top edge. If you set the Edge to
<Larger>, TouchKit will extend the horizontal position of the
top edge.
12
TR-7190 User Manual
INTRODUCTION
Bottom
If you set the Edge to <Smaller>, TouchKit will reduce the
horizontal position of the bottom edge. If you set the Edge to
<Larger>, TouchKit will extend the horizontal position of the
bottom edge.
Left
If you set the Edge to <Smaller>, TouchKit will reduce the
vertical position of the left edge. If you set the Edge to <Larger>,
TouchKit will extend the vertical position of the left edge.
Right
If you set the Edge to <Smaller>, TouchKit will reduce the vertical
position of the right edge. If you set the Edge to <Larger>,
TouchKit will extend the vertical position of the right edge.
In some cases, the cursor will be behind the finger when you touch the
panel. If you cannot see the cursor, you can set the X Axis or Y Axis to
move the cursor.
Offset X Axis
If you set the Offset X Axis to <Smaller>, cursor will be moved
one pixel to the left of the X Axis. If you set the Offset X Axis to
<Larger>, cursor will be moved one pixel to the right of the X Axis.
Offset Y Axis
If you set the Offset Y Axis to <Smaller>, cursor will be moved
one pixel above the Y Axis. If you set the Offset Y Axis to <
Larger>, cursor will be moved one pixel below the Y Axis.
13
TR-7190 User Manual
INTRODUCTION
Edge Compensation Switch
Use the +10% and -10% button to adjust. If you press the +10% button,
the top, bottom, left and right edges will extend 10%, and the cursor will
be moved 10 pixels from the X and Y Axis to the right and top. If you
press the -10% button, the top, bottom, left and right edges will contract
10%, and cursor will be moved 10 pixels from the X and Y Axis to the left
and bottom.
Choose the Default button to restore the default settings.
4. MONITORS: Multiple Monitors, Split Monitor
Multiple Monitors
To configure the mapping relationship between the
monitors and the touch panels, select the monitor
page as below.
Set the check box (Use Multiple Monitors) to enable multiple monitors
mapping. Unchecking this box will disable multiple-monitor configuration,
and all of the touch panel controllers will be mapped to the primary
monitor. The gray shadow area is the monitor mapped to the selected
controller/panel. The button [Mapping] is used to find the mapping
relationships between the monitors and touch panel controllers. Press
[Mapping] and the software will guide you to touch the corresponding
monitor to obtain the mapping relationship.
14
TR-7190 User Manual
INTRODUCTION
After completing monitor mapping, Press [Apply] to apply the mapping
relationship.
Split Monitors
To use the Split Monitor function, you need to select which controller you
want to launch this function, then check the Multiple Monitors box and
Split Monitor at the same time as shown below. Press the [Split Monitor]
button to set up the active area.
It shows the current resolution of the display and you can set the active
area by inputting the value or use the default button [Upper Half],
[Left Half] or [Quarter]. The default value of panel resolution should be
full screen as Left: 0, Right: 0, Top: 0 and Bottom: 0.
5. ABOUT: General information about TouchKit.
Uninstalling TouchKit
To uninstall, use the TouchKit/Uninstall from the Programs menu on the
Start button.
15
TR-7190 User Manual
This page is intentionally left blank.
16
TR-7190 User Manual
TR-999 SBC INTRODUCTION
TR-999 SBC Introduction
This chapter describes the TR-7001 single board computer, TR-999.
The topics covered in this chapter are as follows:
Product Description ...................................................................................... 18
TR-999 Specifications .................................................................................. 19
Board Dimensions ......................................................................................... 20
17
TR-7190 User Manual
TR-999 SBC INTRODUCTION
TR-999 SBC Introduction
Product Description
The TR-999 PICMG 1.3 SHB Express CPU Card is based on the latest
Intel® Q67 chipset. The platform supports 3rd generation Intel® Core
processor family with LGA1155 packing and features an integrated
dual-channel DDR3 memory controller as well as a graphics core.
The latest Intel® processors provide advanced performance in both
computing and graphics quality. This meets the requirement of
customers in the gaming, POS, digital signage and server market
segment.
The Q67 platform is made with 32-nanometer technology that supports
Intel’s first processor architecture to unite the CPU and the graphics core
on the transistor level. The TR-999 SHB board utilizes the dramatic
increase in performance provided this Intel’s latest cutting-edge
technology. Dimensions of the board are 338mm x 126mm.
75FEATURES:







18
Supports Intel® 3rd Generation Core i7/i5/i3 QC/DC desktop
processors
Two DDR3 DIMM, 1066/1333MHz, Max. 16GB memory
Dual Intel® PCI-Express Gigabit LAN
Integrated Graphics for CRT, DVI-I, LVDS displays
2x SATA 2.0, 2x SATA 3.0, 9x USB 2.0,
2x COM, Watchdog timer
2x SATA 2.0, 4x USB 2.0 for PICMG 1.3 backplane
1x PCI-E (x16), 1x PCI-E (x4), 4x PCI for PICMG 1.3
backplane
TR-7190 User Manual
TR-999 SBC INTRODUCTION
75Specifications
Product Name
Form Factor
CPU Type
TR-999
PICMG 1.3 SHB Express full size CPU card
- Intel® Sandy Bridge 32nm QC/DC DT processor w/ IMC & Gfx
- LGA package[37.5 mm x 37.5mm](TDP: QC= 95W/65W ; DC = 65W)
**Sandy Bridge-DT is NOT socket compatible with Clarkdale/Lynnfield
Up to 3.1GHz
CPU Speed
Up to 8MB
Cache
CPU Socket
LGA1155 (Socket H2)
Intel® Q67 PCH
Chipset
27 x 27 mm package size
AMI BIOS, support ACPI Function
BIOS
Intel® CoreTM i7/i5/i3 DT processor integrated memory controller
Memory
DDR3 1066/1333 MHz (Non-ECC)
DIMM x 2, Max. 16GB
- Intel® 3rd generation CoreTM i7/i5/i3 mobile processor integrated Gfx
VGA
 VGA
 DVI-D X 1 (thru Level shifter ASM1442)
 LVDS : 24-bit dual channel (Chrontel CH7308 via SDVO)
1. Intel® Q67 Gigabit MAC + PHY :Intel® 82579V GbE x1
LAN
2. Intel® 82583V PCI-e Gigabit LAN controller x1
USB
Intel® Q67 built-in USB 2.0 host controller, support 14 ports
10 ports on SHB, 4 ports to the backplane [Connector C]
Intel® Q67 PCH built-in SATA controller, supports total 6 ports
Serial ATA
2 x SATA (3.0) 6Gbps+ 4 x SATA (2.0) 3Gbps ports
[2 x SATA 2.0 ports to the backplane Connector C]
Intel® Q67 built-in high definition audio w/ Realtek ALC662 Codec
Audio
Winbond W83627DHG-P
LPC I/O
COM1 (RS232 only), COM2 (RS232/422/485)
Hardware Monitor (2 thermal inputs, 4 voltage monitor inputs & 3 Fan headers)
4 Pin PWM _Fan x 1+3 Pin DC_Fan x2
4 in & 4 out
Digital IO
Supports PS/2 Keyboard/Mouse connector [KB 1st priority]
KB/Mouse
Expansion Slots Mini PCI-express socket x1@solder side [Full-sized]; [Support USB client]
PS/2 Connector x1 for keyboard/mouse
Edge
DB15 for VGA, 2x RJ45 for LAN 1 & 2, 1x USB 2.0
Connectors
1x PCIe (16x) [Connector A & B]
Interface
4x PCIe (1x) or 1x PCIe (4x) [Connector A]
4x PCI masters [Connector D]
2x DF13 for 24-bit LVDS
Onboard
1x 4-pin box header for brightness control
Header/
1x DF11-20-pin header for DVI
Connector
2x13 pins box-header x1 for Printer
2x DF11-10-pin box-header for COM1/ COM2
4x 8-pin header for USB1-8
1x 12-pin header for Audio (Line-Out, Line-In & Mic)
1x 10-pin header Digital I/O
1x 4-pin header for CPU fan (PWM smart fan)
1x 3-pin x2 header for system fan (DC-fan)
6x SATA (Black connectors x4 for SATA2; Blue connectors x2 for SATA 3)
1x 10-pin header Front panel
Watchdog Timer Yes (256 segments, 0, 1, 2…255 sec/min)
ATX
System
Voltage
LAN Wakeup
Others
338mm x 126mm
Board Size
19
TR-7190 User Manual
TR-999 SBC INTRODUCTION
[
Board Dimensions
20
TR-7190 User Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the TR-999 in order to set up a workable system. The
topics covered are:
Installing the CPU ................................................................................. 22
Installing the Memory ........................................................................... 23
Setting the Jumpers................................................................................ 24-28
Connectors on TR-999.......................................................................... 29-37
21
TR-7001 User Manual
TR-7190
INSTALLATIONS
Installing the CPU
The TR-999 board supports an LGA1155 Socket (shown below) for
Intel Sandy Bridge processors.
To install the CPU, unlock first t he socket by pressi ng t he l ever
sideways, then lift it up to a 90-degree. Then, position the CPU above the
socket such that the CP U corner aligns with the gold triangle matching
the socket corner with a small triangle. Carefully insert the CPU into the
socket and push down the lever to secure the CPU. Then, install the heat
sink and fan.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
22
TR-7190 User Manual
INSTALLATIONS
Installing the Memory
The TR-999 board supports two DDR3 memory socket for a maximum
total memory of 16GB in DDR3 DIMM memory type.
Installing and Removing Memory Modules
To install the DDR3 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR3 module so that the key of the DDR3 module aligned
with that on the memory slot.
2. Gently push the DDR3 module in an upright position until the clips of
the slot close to hold the DDR3 module in place when the DDR3
module touches the bottom of the slot.
3. To remove the DDR3 module, press the clips with both hands.
Lock
Lock
23
DDR3 Module
Lock
Lock
TR-7190 User Manual
INSTALLATIONS
Setting the Jumpers
Jumpers are used on TR-999 to select various settings and features
according to your needs and applications. Contact Transduction if you
have doubts about the best configuration for your needs. The following
lists the connectors on TR-999 and their respective functions.
Jumper Locations on TR-999................................................................. 25
JP1, JP2, JP3: RS232/RS422/RS485 (COM2) Selection....................... 26
JP4: COM2 RS232 RI/+5V/+12V Power Setting.................................. 26
JP5: COM1 RS232 RI/+5V/+12V Power Setting.................................. 26
JP7: ME TLS DISABLE/ENABLE (Factory use only)......................... 26
JP8: Flash Descriptor Security Override (Factory use only) ................. 27
JP9: LVDS Panel Power Select ............................................................. 27
JP10: Backlight Adjust .......................................................................... 27
JP11: PWM voltage setting(Factory use only) ...................................... 27
JP12: SRTC RST#(Factory use only) .................................................... 27
JP13: Backlight Enable.......................................................................... 28
JP14: ATX or AT (Emulation) Mode Selection .................................... 28
JBAT1: Clear CMOS Contents.............................................................. 28
24
TR-7190 User Manual
INSTALLATIONS
Jumper Locations on TR-999
25
TR-7190 User Manual
INSTALLATIONS
JP1, JP2, JP3: RS232/RS422/RS485 (COM2) Selection
COM2
Function
Jumper
Setting
(Pin closed)
RS-232
RS-422
RS-485
JP1:
1-2
JP1:
3-4
JP1:
5-6
JP2
3-5&4-6
JP2:
1-3&2-4
JP2:
1-3&2-4
JP3:
3-5&4-6
JP3:
1-3&2-4
JP3:
1-3 & 2-4
JP4: COM2 RS232 RI/+5V/+12V Power Setting
JP4
Setting
Function
Pin 1-2
+12V
Short/Closed
Pin 3-4
RI
Short/Closed
Pin 5-6
+5V
Short/Closed
Note: The suggested setting is RI, with maximum current lower than 1A.
JP5: COM1 RS232 RI/+5V/+12V Power Setting
JP5
Setting
Function
Pin 1-2
+12V
Short/Closed
Pin 3-4
RI
Short/Closed
Pin 5-6
+5V
Short/Closed
Note: The suggested setting is RI, with maximum current lower than 1A.
JP7: ME TLS DISABLE/ENABLE (Factory use only)
ME TLS Disable/Enable
JP7
Disabled
Open
(Default)
Close
26
Enabled
TR-7190 User Manual
INSTALLATIONS
JP8: Flash Descriptor Security Override (Factory use only)
JP8
Open
Flash Descriptor
Security Override
Disabled
(Default)
Close
Enabled
JP9: LVDS Panel Power Select
JP9
Setting
Panel Voltage
Pin 1-2
Short/Closed
3.3V (default)
Pin 2-3
Short/Closed
5V
JP10: Backlight Adjust
JP10
Setting
Panel Voltage
OPEN
3.3V (default)
CLOSE
5V
JP11: PWM voltage setting(Factory use only)
JP12: SRTC RST#(Factory use only)
JP12
Setting
Pin 1-2
Short/Closed
(Default)
Pin 2-3
Short/Closed
27
Function
Normal
Clear ME
TR-7190 User Manual
INSTALLATIONS
JP13: Backlight Enable
JP13
Setting
Panel Voltage
OPEN
3.3V (default)
CLOSE
5V
JP14: ATX or AT (Emulation) Mode Selection
JP14
Setting
AT (Emulation)
ATX
1-2: AT (Emulation), for SYS PWR_ON. Automatic power on comes
after a 200ms delay.
2-3: ATX Mode, SYS PWR_ON for manual control
JBAT1: Clear CMOS Contents
JBAT1
28
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
TR-7190 User Manual
INSTALLATIONS
Connectors on TR-999
Connector Locations on TR-999 ......................................................... 30
CN1: ATX 12V Power Connector ...................................................... 31
CN2.CN4: SATA 3.0 Connectors(Blue) ............................................. 31
CN6: DB-15 VGA Connector ............................................................. 31
CN7: USB2.0 Connector ..................................................................... 31
CN8: Gigabit LAN (Intel 82579V) ..................................................... 31
CN9: Gigabit LAN (Intel 82583V) ..................................................... 31
CN10: PS/2 Keyboard and Mouse Connector..................................... 31
J2: Front Panel Function...................................................................... 32
J8: SPI Flash (Factory use only).......................................................... 33
J9: Digital I/O Port .............................................................................. 33
J10: Parallel Port.................................................................................. 33
J11: USB 2/3 Ports .............................................................................. 34
J12: USB 6/7 Ports .............................................................................. 34
J13: USB 4/5 Ports .............................................................................. 34
J14: USB 8/9 Ports .............................................................................. 34
J15: DVI-D Port .................................................................................. 35
J17: Mini PCIE Connector .................................................................. 35
J18: LCD Backlight Control................................................................ 35
J19: External PS/2 Keyboard Port ....................................................... 35
J20: External PS/2 Mouse Port............................................................ 36
J21, J22: LVDS Connector (2nd channel, 1st channel)....................... 36
J23: External Audio Connector ........................................................... 37
CPU_FAN0: CPU Fan0 Power Connector.......................................... 37
CPU_FAN1: CPU Fan1 Power Connector.......................................... 37
SYS_FAN1: System Fan1 Power Connector ...................................... 37
29
TR-7190 User Manual
INSTALLATIONS
Connector Locations on TR-999
30
TR-7190 User Manual
INSTALLATIONS
CN1: ATX 12V Power Connector
This connector supplies the CPU operating voltage.
Pin #
Signal Name
1 Ground
2 Ground
3 +12V
4 +12V
CN2.CN4: SATA 3.0 Connectors(Blue)
CN3.CN5: SATA 2.0 Connectors(Black)
CN6: DB-15 VGA Connector
Signal Name Pin #
Red 1
Blue 3
GND 5
GND 7
VCC 9
N.C. 11
HSYNC 13
DDCCLK 15
Pin # Signal Name
2
Green
4
N.C.
6
GND
8
GND
10
GND
12
DDCDATA
14
VSYNC
CN7: USB2.0 Connector
CN8: Gigabit LAN (Intel 82579V)
CN9: Gigabit LAN (Intel 82583V)
This RJ45 LAN connector features for LAN wakeup.
CN10: PS/2 Keyboard and Mouse Connector
CN10 uses a Y-cable with dual D-connectors.
Pin #
Signal Name
1 Key
board Data
2M
ouse Data
3 Ground
4 Vcc
5 Key
board Clock
6M
ouse Clock
31
TR-7190 User Manual
INSTALLATIONS
J2: Front Panel Function
Signal Name
Speaker out
No connect
Pin #
+5V
No connect
No connect
1
34
5
78
9 10
11 12
No connect
15 16
GND
PWR_SW 13
RST 17
HDD LED -
Pin #
Signal Name
2
PWR LED +
6
14
18
20
19
No connect
GND
NC
GND
GND
PWR_SW
No connect
GND
HDD LED +
J3: DDR3 DIMM Socket Channel B
J7: DDR3 DIMM Socket Channel A
J5: COM2 Serial Port(RS232/422/485)
Please refer to JP1, JP2, JP3: RS232/422/485 (COM2) Selection
Pin #
RS-232
1 DCD
2 RX
3 TX
4 DTR
5 Ground
6 DSR
7 RTS
8 CTS
9 RI
10 NC
32
Signal Name
R2-422
RS-485
TXTX+
RX+
RXGround
RTSRTS+
CTS+
CTSNC
DATADATA+
NC
NC
Ground
NC
NC
NC
NC
NC
TR-7190 User Manual
INSTALLATIONS
J6: COM1 Serial Port(RS232)
J8: SPI Flash (Factory use only)
J9: Digital I/O Port
Signal Name
GND 1
OUT3 3
OUT2 5
IN3 7
IN2 9
Pin
Pin
2
4
6
8
10
Signal Name
VCC
OUT1
OUT0
IN1
IN0
J10: Parallel Port
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy 11
Paper empty
Select 13
33
Pin #
1
2
3
4
5
6
7
8
9
10
12
Pin #
14
15
16
17
18
19
20
21
22
23
24
25
26
Signal Name
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
TR-7190 User Manual
INSTALLATIONS
J11: USB 2/3 Ports
The following table shows the pin outs of the USB2.0 pin header.
Signal Name
Vcc 1
USB2- 3
USB2+ 5
Ground 7
Pin
Pin
2
4
6
8
Signal Name
Ground
USB3+
USB3Vcc
J12: USB 6/7 Ports
The following table shows the pin outs of the USB2.0 pin header
Signal Name
Vcc 1
USB6- 3
USB6+ 5
Ground 7
Pin
Pin
2
4
6
8
Signal Name
Ground
USB7+
USB7Vcc
J13: USB 4/5 Ports
The following table shows the pin outs of the USB2.0 pin header
Signal Name
Vcc 1
USB4- 3
USB4+ 5
Ground 7
Pin
Pin
2
4
6
8
Signal Name
Ground
USB5+
USB5Vcc
J14: USB 8/9 Ports
The following table shows the pin outs of the USB2.0 pin header
Signal Name
Vcc 1
USB8- 3
USB8+ 5
Ground 7
34
Pin
Pin
2
4
6
8
Signal Name
Ground
USB9+
USB9Vcc
TR-7190 User Manual
INSTALLATIONS
J15: DVI-D Port
J15 is a 20-pin header that is used to connect to the optional DVI-D
cable.
The following table shows the pin outs of the DVI-D pin header.
Signal Name Pin #
TDC1#_B 2
Ground 4
TLC#_B 6
5V 8
N.C. 10
TDC2#_B 12
Ground 14
TDC0#_B 16
N.C. 18
SC_DDC_B 20
Pin # Signal Name
1
TDC1_B
3
Ground
5
TLC_B
7
Ground
9
HPDET_B
11
TDC2_B
13
Ground
15
TDC0_B
17 N.C
.
19
SD_DDC_B
J17: Mini PCIE Connector
J18: LCD Backlight Control
Pin #
Signal Name
1 +12V
2B
acklight Enable
3B
acklight Adj
4 GND
J19: External PS/2 Keyboard Port
The following table shows the pin outs of the PS/2 keyboard pin header.
Pin #
1 KB
2 KB
3 N.C
4 Ground
5 Vcc
35
J19
clock
data
.
TR-7190 User Manual
INSTALLATIONS
J20: External PS/2 Mouse Port
The following table shows the pin outs of the PS/2 mouse pin header.
Pin #
1M
2 N.C
3 GND.
4M
5 Vcc
J20
ouse data
ouse clock
J21, J22: LVDS Connector (2nd channel, 1st channel)
The LVDS connectors, DF13 20-pi n mating connectors, are composed
of the 2nd channel (J21) and 1st channel (J22) to support 18-bit or 24bit
J22: first channel
Signal Name Pin # Pin # Signal Name
TX0- 2
1
TX0+
Ground 4
3 Ground
TX1- 6
5
TX1+
*5V/3.3V 8
7
Ground
TX3- 10
9
TX3+
TX2- 12
11
TX2+
Ground 14
13 Ground
TXC1- 16
15
TXC1+
*5V/3.3V 18
17
BKL_EN
+12V 20
19 +12V
*JP9 can be used to set 3.3V or 5V.
J21: Second channel
Signal Name Pin #
TX4- 2
Ground 4
TX5- 6
*5V/3.3V 8
TX7- 10
TX6- 12
Ground 14
TXC2- 16
*5V/3.3V 18
+12V 20
Pin # Signal Name
1
TX4+
3 Ground
5
TX5+
7
Ground
9
TX7+
11
TX6+
13 Ground
15
TXC2+
17
BKL_EN
19 +12V
*JP9 can be used to set 3.3V or 5V.
36
TR-7190 User Manual
INSTALLATIONS
J23: External Audio Connector
J23 is a 12-pin header that is used to connect to the optional audio cable.
Signal Name
LINE OUT_L
JD_FRONT 3
LINE IN_L
JD LINE IN
MIC-L 9
JD MIC1
Pin #
1
5
7
11
Pin #
2
4
6
8
10
12
Signal Name
LINE OUT_R
Ground
LINE IN R
Ground
MIC-R
Ground
CPU_FAN0: CPU Fan0 Power Connector
Pin #
Signal Name
1 Ground
2 +12V
3 Ro
tation detection
4C
ontrol
Note: CPU_FAN0 for PWM FAN mode
[
CPU_FAN1: CPU Fan1 Power Connector
Pin #
Signal Name
1 Ground
2 +12V
3 Ro
tation detection
Note: CPU_FAN0 for DC FAN mode
SYS_FAN1: System Fan1 Power Connector
Pin #
Signal Name
1 Ground
2 +12V
3 NC
Note: SYS_FAN1 for DC FAN mode
37
TR-7190 User Manual
INSTALLATIONS
This page is intentionally left blank.
38
TR-7190 User Manual
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the AMI BIOS
that comes with the board. The topics covered in this chapter are as
follows:
BIOS Introduction ........................................................................................ 40
BIOS Setup .................................................................................................... 40-41
Advanced Settings ........................................................................................ 42-43
Chipset Settings ............................................................................................ 54-57
Boot Settings ................................................................................................. 58
Security Settings ........................................................................................... 59
Save & Exit Settings .................................................................................... 60-61
39
TR-7190 User Manual
BIOS SETUP
BIOS Introduction
The BIOS (Basic Input/Output Sy stem) i nstalled i n y our com puter
system’s ROM supports Intel proce ssors. The BIOS provides critical
low-level support for a standard device such as disk drives, serial ports
and parallel ports. It also password protection as well as special support
for detailed fine-tuning of the chipset controlling the entire system.
BIOS Setup
The BIOS provides a Setu p u tility p rogram fo r sp ecifying th e system
configurations and set tings. The B IOS R OM of t he sy stem st ores t he
Setup utility. When you turn on the computer, the BIOS is immediately
activated. Pressing the <Del> key im mediately allows you to enter the
Setup utility. If you are a little b it late p ressing the <Del> k ey, POST
(Power On Self Test) will continue with its test routines, thus preventing
you from invoking the Setup. If you still wish to enter Setup, restart the
system by pressi ng t he ”R eset” but ton or simultaneously pressing the
<Ctrl>, <Alt> an d <Delete> keys. You can also restart by turning the
system Off and back On again. The following message will ap pear on
the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
40
TR-7190 User Manual
BIOS SETUP
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both AMI and your system manufacturer
to provide the absolute maximum performance and
reliability. Changing the defaults could cause the system to
become unstable and crash in some cases.
System Language
Choose the system default language.
System Date
Set the Date. Use Tab to switch between Data elements.
System Time
Set the Time. Use Tab to switch between Data elements.
41
TR-7190 User Manual
BIOS SETUP
Advanced Settings
This section allows you t o confi gure and i mprove y our sy stem and
allows you to set up some system features according to your preference.
Aptio Setup Utility
Advanced
Main
Chipset
Legacy OpROM Support
Launch PXE OpROM
Launch Storage OpROM
Settings
up event setting
► CPU Configuration
► SATA Configuration
► Shutdown Temperature Configuration
► PCI IRQ Configuration
► Intel IGD SWSCI OpRegion
► USB Configuration
► Super IO Configuration
► H/W Monitor
Boot
Security
Save & Exit
Disabled
Enabled
► ACPI
► Wake
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Launch PXE OpROM
Enable or Disable Boot Option for Legacy Network Devices.
Launch Storage OpROM
Enable or Di sable Boot Option for Legacy Mass Storage Devices with
Option ROM.
42
TR-7190 User Manual
BIOS SETUP
ACPI Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Enable ACPI Auto Configuration
Disabled
Enable Hibernation
ACPI Sleep State
Lock Legacy Resources
Enabled
S1 (CPU stop clock)
Disabled
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Enabled ACPI Auto Configuration
Enables or Disables BIOS ACPI Auto Configuration.
Enable Hibernation
Enables o r Disab les System ab ility to Hib ernate (OS/S4 Sleep State).
This option may be not effective with some OS.
ACPI Sleep State
Select th e h ighest ACPI sleep state th e system will enter, when the
SUSPEND button is pressed.
Lock Legacy Resources
Enabled or Disabled Lock of Legacy Resources.
43
TR-7190 User Manual
BIOS SETUP
Wake up event settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Wake system with Fixed Time
Wake up hour
Wake up minute
Wake up second
Disabled
0
0
0
Wake on Ring
Wake on PCI PME
Wake on PCIE Wake Event
Disabled
Disabled
Disabled
Security
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Wake system with Fixed Time
Enables or Disables System wake on alarm event. W hen enabled,
System will wake on the hr::min:: sec specified.
Wake on Ring
The options are Disabled and Enabled.
Wake on PCI PME
The options are Disabled and Enabled.
Wake on PCIE PME Wake Event
The options are Disabled and Enabled.
44
TR-7190 User Manual
BIOS SETUP
CPU Configuration
This section shows the CPU configuration parameters.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
CPU Configuration
Intel® Core ™ i5-2400 CPU @ 3.10GHz
Processor Stepping
Microcode Revision
Processor Speed
Processor Cores
Intel HT Technology
EMT64
206a7
d
3100 MHz
4
Not Supported
Supported
Hyper-threading
Active Processor Cores
Limit CPUID Maximum
Execute Disable Bit
Hardware Prefetcher
Adjacent Cache Line Prefetch
Intel Virtualization Technology
Power Technology
Local x2APIC
Enabled
All
Disabled
Enabled
Enabled
Enabled
Disabled
Energy Efficient
Disabled
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Hyper-threading
Enabled for Windows XP and Linux (OS optimized for
Hyper-Threading Technology) and Disabled for other OS (OS not
optimized for Hyper-Threading Technology). When Disabled, only one
thread per enabled core is enabled.
Active Processor Cores
Number of cores to enable in each processor package.
Limit CPUID Maximum
Disabled for Windows XP.
Execute Disable Bit
XD can prevent certain classes of malicious buffer overfl ow at tacks
when com bined wi th a support ing OS (W indows Server 2003 SP1,
Windows XP SP2, SuSE Linux 9.2, Re33dHat Enterprise 3 Update 3.)
Hardware Prefetcher
To turn on/off the MLC streamer prefetcher.
45
TR-7190 User Manual
BIOS SETUP
Adjacent Cache Line Prefetch
To turn on/off prefetching of adjacent cache lines.
Intel Virtualization Technology
When enabled, a VMM can utilize the additional hardware capabilities
provided by Vanderpool Technology.
Power Technology
Enable the power management features.
Local x2APIC
Enable Local x2APIC. Some OSes do not support this.
SATA Configuration
SATA Devices Configuration.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
SATA Configuration
SATA Mode
Serial-ATA Controller 0
Serial-ATA Controller 1
IDE Mode
Compatibled
Enhanced
SATA Port0
SATA Port1
SATA Port2
SATA Port3
SATA Port4
SATA Port5
Not Present
Not Present
Not Present
Not Present
Not Present
Not Present
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
SATA Mode
(1) IDE Mode.
(2) AHCI Mode.
(3) RAID Mode.
Serial-ATA Controller
Enable / Disable Serial ATA Controller.
46
TR-7190 User Manual
BIOS SETUP
Shutdown Temperature Configuration
Aptio Setup Utility
Main
Advanced
Chipset
APCI Shutdown Temperature
Boot
Disabled
Security
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
ACPI Shutdown Temperature
The default setting is Disabled.
.
47
TR-7190 User Manual
BIOS SETUP
PCI IRQ Configuration
Aptio Setup Utility
Advanced
Main
Chipset
Boot
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
IRQ10
IRQ11
IRQ12
Security
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
PCI/ISA
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Intel IGD SWSCI OpRegion
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Intel IGD SWSCI OpRegion Configuration
DVMT Mode Select
DVMT/FIXED Memory
IGD - Boot Type
LCD Panel Type
Panel Scaling
DVMT Mode
256MB
VBIOS Default
1024x768 LVDS
Auto
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
DVMT Mode Select
Select DVMT Mode used by Internal Graphics Device.
DVMT/FIXED Memory
Select DVM T/FIXED M ode M emory si ze used by Internal Graphics
Device. Options are 128MB, 256MB and Maximum.
IGD - Boot Type
Select the Video Device that will be activated during POST. This has no
effect if external graphics present.
Note: When using the DVI port only, choose EFP option.
48
TR-7190 User Manual
BIOS SETUP
LCD Panel Type
Select LCD Panel used by Internal
appropriate setup item.
Graphics Device by sel ecting t he
Panel Scaling
Select t he LC D panel scal ing opt ion used by t he Int ernal Graphi cs
Device.
49
TR-7190 User Manual
BIOS SETUP
USB Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
USB Configuration
→ ← Select
USB Devices:
2 Hubs
Legacy USB Support
EHCI Hand-off
Port 60/64 Emulation
Enabled
Disabled
Enabled
USB hardware delays and time-outs:
USB Transfer time-out
Device reset tine-out
Device power-up delay
20 sec
20 sec
AUTO
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Legacy USB Support
Enables Legacy USB support.
AUTO option disables legacy support if no USB devices are connected.
DISABLE option will keep USB devices available only for EFI
applications.
50
TR-7190 User Manual
BIOS SETUP
EHCI Hand-off
Enabled/Disabled. This is a workaround for OSes without EHCI
hand-off support. The EHCI ownership change should be claimed by
EHCI driver.
Port 64/60 Emulation
Enables I/O port 60h/64h emulation support. This should be enabled for
the complete USB keyboard legacy support for non-USB aware OSes.
USB Transfer time-out
The time-out value for Control, Bulk, and Interrupt transfers.
Device reset tine-out
USB mass Storage device start Unit command time-out.
Device power-up delay
Maximum time the device will take before it properly reports itself to the
Host Controller. ‘Auto’ uses default value: for a Root port it is 100ms, for
a Hub port the delay is taken from Hub descriptor.
51
TR-7190 User Manual
BIOS SETUP
Super IO Configuration
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Super IO Configuration
Super IO Chip
► Serial Port 0 Configuration
► Serial Port 1 Configuration
► Parallel Port Configuration
Restore AC Power Loss
Power On Function
LCD Backlight Control
Winbond W83627DHG
Always off
None
1(Max)
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Serial Port Configuration
Set Parameters of Serial Ports. User can Enable/Disable the serial port
and Select an optimal settings for the Super IO Device.
Restore AC Power Loss
Always on
Always off (default)
Power On function
None (default)
Mouse Left
Mouse Right
Any key
LCD Backlight Control
1(Max) (default)
2
3
4
5
6
7
8(Min)
52
TR-7190 User Manual
BIOS SETUP
H/W Monitor
Aptio Setup Utility
Main
Advanced
Chipset
CPU Smart Fan Control
SYSTIN temperature
CPUTIN temperature
SYS FAN Speed
CPU FAN0 Speed
CPU FAN1 Speed
CPUVCORE
VCC12
3VCC
DDR 1.5V
VCC5
3VSB
Boot
[Disabled]
+39 C
+38 C
N/A
N/A
N/A
+ 1.184V
+12.355V
+3.456 V
+1.520 V
+5.171 V
+3.456 V
Security
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Temperatures/Voltages
These fields are the param eters of t he hardware m onitoring funct ion
feature of the m otherboard. The va lues are read-only values
as
monitored by the system and show the PC health status.
CPU Smart Fan Control
Disabled (default)
55 C
60 C
65 C
70 C
53
TR-7190 User Manual
BIOS SETUP
Chipset Settings
This section allows you t o confi gure and i mprove y our sy stem and
allows you to set up some system features according to your preference.
Aptio Setup Utility
Advanced
Main
► North
► South
Chipset
Boot
Security
Bridge
Bridge
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
North Bridge
This item shows the North Bridge Parameters.
South Bridge
This item shows the South Bridge Parameters.
54
TR-7190 User Manual
BIOS SETUP
North Bridge
This section allows you to configure the North Bridge Chipset.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Memory Information
Total Memory
4096 MB (DDR3 1066)
Memory SlotA
Memory SlotB
2048 MB (DDR3 1066)
2048 MB (DDR3 1066)
Low MMIO Align
1024M
DMI Gen2
Enabled
VT-d
Disabled
Initiate Graphic Adapter
IGD Memory
Render Standby
IGD Multi-Monitor
PEG/IGD
64M
Enabled
Disabled
PCI Express Port
PEG Force Gen1
Detect Non-Compliance
Auto
Disabled
Disabled
→ ←
Select Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Low MMIO Align
Low MMIO resources align at 64MB/1024MB.
VT-d
VT-d Enable/Disable.
Initiate Graphic Adapter
Select which graphics controller to use as the primary boot device.
Options are IGD, PCI/IGD, PCI/PEG, PEG/IGD, PEG/PCI and SG.
IGD Memory
IGD Share Memory Size. Options are Disable, 32M, 64M and 128M.
Render Standby
Enabled/Disabled Render standby by Internal Graphics Device.
IGD Multi-Monitor
Enabled/Disabled IGD Multi-Monitor by Internal Graphics Device.
55
TR-7190 User Manual
BIOS SETUP
PCI Express Port
Options are Disabled, Enabled and Auto.
PEG Force Gen1
PCI Express Port Force Gen1. Options are Disabled and Enabled.
Detect Non-Compliance
Detect Non-Compliance PCI Express Device in PEG.
SB Chipset Configuration
This section allows you to configure the South Bridge Chipset.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
SB Chipset Configuration
GbE Controller
Wake on LAN from S5
Enabled
Enabled
Audio Configuration
Azalia HD Audio
Enabled
High Precision Event Timer Configuration
High Precision Timer
Enabled
PCI Express Ports Configuration
USB Configuration
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
GbE Controller
This is constantly enabled.
Wake on LAN from S5
Wake on LAN from S5 help.
Audio Configuration
The Audio Configuration settings Enable/Disable the Azalia HD Audio
and the Azalia internal HDMI codec.
High Precision Event Timer Configuration
Enable/or Disable the High Precision Event Timer.
56
TR-7190 User Manual
BIOS SETUP
PCI Express Ports Configuration
Enable or Disable the PCI Express Ports in the Chipset.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
PCI Express Ports Configuration
PCI Express Port 1
PCI Express Port 2
PCI Express Port 3
PCI Express Port 4
PCI Express Port 5
PCI Express Port 6
PCI Express Port 7
PCI Express Port 8
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
PCIe Sub Decode
Disabled
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
USB Configuration
Enable/Disable All USB Devices, USB 2.0 (EHCI) Support and RMH
Support. The setting of AUTO on RMH Support Enable RMH support
on Ibex Peak B0 Stepping.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
USB Configuration
57
All USB Devices
Enabled
EHCI Controller 1
EHCI Controller 2
Enabled
Enabled
USB Port 0
USB Port 1
USB Port 2
USB Port 3
USB Port 4
USB Port 5
USB Port 6
USB Port 7
USB Port 8
USB Port 9
USB Port 10
USB Port 11
USB Port 12
USB Port 13
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
TR-7190 User Manual
BIOS SETUP
Boot Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Boot Configuration
Setup Prompt Timeout
Bootup NumLock State
1
On
Quiet Boot
Fast Boot
Disabled
Disabled
CSM16 Module Version
07.64
GateA20 Active
Option ROM Messages
Interrupt 19 Canture
Security
Upon Request
Force BIOS
Disabled
Boot Option Priorities
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Hard Drive BBS Priorities
Setup Prompt Timeout
Number of seconds to wait for setup activation key.
65535(0xFFFF) means indefinite waiting.
Bootup NumLock State
Select the keyboard NumLock state.
Quiet Boot
Enables/Disables Quiet Boot option.
Fast Boot
Enables/Disables boot with initialization of a minimal set of devices required
to launch active boot option. Has no effect for BBS boot options.
GateA20 Active
UPON REQUEST – GA20 can be disabled using BIOS services.
ALWAYS – do not allow disabling GA20; this option is useful when anyRT
code is executed above 1MB.
Option ROM Messages
Set display mode for Option ROM. Options are Force BIOS and Keep
Current.
Interrupt 19 Capture
Enable: Allows Option ROMs to trap Int 19.
Boot Option Priorities
Sets the system boot order.
58
TR-7190 User Manual
BIOS SETUP
Security Settings
This section allows you t o confi gure and i mprove y our sy stem and
allows you to set up some system features according to your preference.
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save & Exit
Password Description
If ONLY the Administrator’s password is set, then
this only limits access to Setup and is only asked
for when entering Setup.
If ONLY the User’s password is set, then this is a
power on password and must be entered to boot
or enter Setup. In Setup the User will have
Administrator rights
Administrator Password
User Password
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Administrator Password
Set Setup Administrator Password.
User Password
Set User Password.
59
TR-7190 User Manual
BIOS SETUP
Save & Exit Settings
Aptio Setup Utility
Main
Advanced
Chipset
Boot
Security
Save Changes and Exit
Discard Changes and Exit
Save Changes and Reset
Discard Changes and Reset
Save Options
Save Changes
Discard Changes
Restore Defaults
Save as User Defaults
Restore User Defaults
Save & Exit
→ ← Select
Screen
↑↓ Select Item
Enter: Select
+- Change Field
F1: General Help
F2: Previous Values
F3: Optimized Default
F4: Save ESC: Exit
Boot Override
Launch EFI Shell from filesystem device
Save Changes and Exit
Exit system setup after saving the changes.
Discard Changes and Exit
Exit system setup without saving any changes.
Save Changes and Reset
Reset the system after saving the changes.
Discard Changes and Reset
Reset system setup without saving any changes.
Save Changes
Save Changes done so far to any of the setup options.
Discard Changes
Discard Changes done so far to any of the setup options.
Restore Defaults
Restore/Load Defaults values for all the setup options.
60
TR-7190 User Manual
BIOS SETUP
Save as User Defaults
Save the changes done so far as User Defaults.
Restore User Defaults
Restore the User Defaults to all the setup options.
Boot Override
Pressing ENTER causes the system to enter the OS.
Launch EFI Shell from filesystem device
Attempts to Launch EFI Shell application (Shellx64.efi) from one of the
available filesystem devices.
61
TR-7190 User Manual
BIOS SETUP
This page is intentionally left blank.
62
TR-7190 User Manual
DRIVERS INSTALLATION
Drivers Installation
This chapter describes the installation procedures for software and
drivers. The software and drivers are included with the motherboard. If
you find the items missing, please contact the vendor where you made
the purchase. The contents of this section include the following:
Intel Chipset Software Installation Utility........................................... 64
VGA Drivers Installation .................................................................... 65
Realtek HD Audio Driver Installation................................................. 66
LAN Drivers Installation ..................................................................... 67-68
Intel® Management Engine Interface ................................................. 69-70
IMPORTANT NOTE:
After installing your Windows operating system, you must install first
the Intel Chipset Software Installation Utility before proceeding with the
drivers installation.
63
TR-7190 User Manual
DRIVERS INSTALLATION
Intel Chipset Software Installation Utility
The Intel Chipset Drivers should be installed first before the software
drivers to enable Plug & Play INF support for Intel chipset components.
Follow the instructions below to complete the installation.
1. Insert the CD that comes with the board. Click Intel and then Intel(R)
QM67/Q67 Chipset Drivers.
2. Click Intel(R) Chipset Software Installation Utility.
3. When th e W elcome screen to th e In tel® Ch ipset Dev ice So ftware
appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
5. On the Readme File Information screen, click Next to continue the
installation.
6. The Set up process i s now com plete. C lick Finish to restart th e
computer and for changes to take effect.
64
TR-7190 User Manual
DRIVERS INSTALLATION
VGA Drivers Installation
NOTE: Before installing the Intel(R) Q67 Chipset Family Graphics
Driver, the Microsoft .NET Framework 3.5 SPI should be first
installed.
1. Insert the CD that comes with the board. Click Intel and then Intel(R)
QM67/Q67 Chipset Drivers.
2. Click Intel(R) Q67 Chipset Family Graphics Driver.
3. When the Welcome screen appears, click Next to continue.
4. C lick Yes to to ag ree with th e licen se agreem ent and continue the
installation.
5. On the Readme File Information screen, click Next to continue the
installation of the Intel® Graphics Media Accelerator Driver.
6. On Setup Progress screen, click Next to continue.
7. Setup complete. Click Finish to restart the computer and for changes
to take effect.
TR-7190 User Manual
DRIVERS INSTALLATION
Realtek HD Audio Driver Installation
Follow the steps below to install the Realtek HD Audio Drivers.
1. Insert the CD that comes with the board. Click Intel and then Intel(R)
QM67/Q67 Chipset Drivers.
2. Click Realtek High Definition Audio Driver.
3. On the Welcome to the InstallShield Wizard screen, click Yes to
proceed with and complete the installation process.
66
TR-7190 User Manual
DRIVERS INSTALLATION
LAN Drivers Installation
1. Insert the CD that comes with the board. Click Intel and then Intel(R)
QM67/Q67 Chipset Drivers.
2. Click Intel(R) PRO LAN Network Driver.
3. When the W elcome screen appears, click Next. On the next screen,
click Yes to to agree with the license agreement.
4. Click the checkbox for Drivers in the Setup Options screen to select
it and click Next to continue.
67
TR-7190 User Manual
DRIVERS INSTALLATION
5. The wi zard is ready to begin installation. Click Install to begin the
installation.
6. When InstallShield Wizard is complete, click Finish.
68
TR-7190 User Manual
DRIVERS INSTALLATION
Intel® Management Engine Interface
REMARKS: The Intel iAMT 7.0 Drivers need install, but
Management Engine Function not support.
Follow the steps below to install the Intel Management Engine.
1. Insert the CD that comes with the board. Click Intel and then Intel(R)
AMT 7.0 Drivers.
2. When the Welcome screen to th e InstallShield W izard for Intel®
Management Engine Components, click Next. On the next screen, click
Yes to to agree with the license agreement.
69
TR-7190 User Manual
DRIVERS INSTALLATION
2. W hen the Setup Progress screen appears, click
Next. Then, click
Finish when the setup progress has been successfully installed.
70
TR-7190 User Manual
APPENDIX
Appendix
A. I/O Port Address Map
Each peri pheral devi ce i n t he sy stem i s assigned a set of I/O port
addresses which also becomes the identity of the device. The following
table lists the I/O port addresses used.
Address
000h - 01Fh
020h - 03Fh
040h - 05Fh
060h - 06Fh
070h - 07Fh
080h - 09Fh
0A0h - 0BFh
0C0h - 0DFh
0F0h
0F1h
1F0h - 1F7h
2F8h - 2FFh
2B0h- 2DFh
360h - 36Fh
3F8h - 3FFh
71
Device Description
DMA Controller #1
Interrupt Controller #1
Timer
Keyboard Controller
Real Time Clock, NMI
DMA Page Register
Interrupt Controller #2
DMA Controller #2
Clear Math Coprocessor Busy Signal
Reset Math Coprocessor
IDE Interface
Serial Port #2(COM2)
Graphics adapter Controller
Network Ports
Serial Port #1(COM1)
TR-7190 User Manual
APPENDIX
B. Interrupt Request Lines (IRQ)
Peripheral devices use i nterrupt request l ines t o not ify C PU for t he
service required. The following table shows the IRQ used by the devices
on board.
Level
Function
IRQ0
System Timer Output
IRQ1 Key
board
IRQ3
Serial Port #2
IRQ4
Serial Port #1
IRQ8
Real Time Clock
IRQ14 Prim
ary IDE
IRQ15 Secondary
IDE
72
TR-7190 User Manual
APPENDIX
C. Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sorts of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user
will restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#include <dos.h>
#include <conio.h>
#include <stdio.h>
#include <stdlib.h>
#include "W627DHG.H"
//--------------------------------------------------------------------------int main (void);
void WDTInitial(void);
void WDTEnable(unsigned char);
void WDTDisable(void);
//--------------------------------------------------------------------------int main (void)
{
char SIO;
abort.\n");
SIO = Init_W627DHG();
if (SIO == 0)
{
printf("Can not detect Winbond 83627DHG, program
}
return(1);
WDTInitial();
WDTEnable(10);
WDTDisable();
return 0;
}
//--------------------------------------------------------------------------void WDTInitial(void)
{
unsigned char bBuf;
bBuf = Get_W627DHG_Reg(0x2D);
bBuf &= (~0x01);
Set_W627DHG_Reg(0x2D, bBuf);
74
//Enable WDTO
TR-7190 User Manual
APPENDIX
//--------------------------------------------------------------------------void WDTEnable(unsigned char NewInterval)
{
unsigned char bBuf;
Set_W627DHG_LD(0x08);
Set_W627DHG_Reg(0x30, 0x01);
bBuf = Get_W627DHG_Reg(0xF5);
bBuf &= (~0x08);
Set_W627DHG_Reg(0xF5, bBuf);
//enable timer
//count mode is second
Set_W627DHG_Reg(0xF6, NewInterval);
//set timer
}
//--------------------------------------------------------------------------void WDTDisable(void)
{
Set_W627DHG_LD(0x08);
Set_W627DHG_Reg(0xF6, 0x00);
//clear
watchdog timer
Set_W627DHG_Reg(0x30, 0x00);
//watchdog
disabled
}
//--------------------------------------------------------------------------//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#ifndef __W627DHG_H
#define __W627DHG_H
1
//--------------------------------------------------------------------------#define
W627DHG_INDEX_PORT
(W627DHG_BASE)
#define
W627DHG_DATA_PORT
(W627DHG_BASE+1)
//--------------------------------------------------------------------------#define
W627DHG_REG_LD
0x07
//--------------------------------------------------------------------------#define W627DHG_UNLOCK
0x87
#define
W627DHG_LOCK
0xAA
//--------------------------------------------------------------------------unsigned int Init_W627DHG(void);
void Set_W627DHG_LD( unsigned char);
void Set_W627DHG_Reg( unsigned char, unsigned char);
unsigned char Get_W627DHG_Reg( unsigned char);
//--------------------------------------------------------------------------#endif
//__W627DHG_H
//--------------------------------------------------------------------------//
// THIS CODE AND INFORMATION IS PROVIDED "AS IS" WITHOUT WARRANTY OF ANY
// KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR
// PURPOSE.
//
//--------------------------------------------------------------------------#include "W627DHG.H"
#include <dos.h>
//--------------------------------------------------------------------------unsigned int W627DHG_BASE;
void Unlock_W627DHG (void);
void Lock_W627DHG (void);
//--------------------------------------------------------------------------unsigned int Init_W627DHG(void)
{
unsigned int result;
unsigned char ucDid;
W627DHG_BASE = 0x4E;
result = W627DHG_BASE;
ucDid = Get_W627DHG_Reg(0x20);
74
TR-7190 User Manual
75
TR-7190 User Manual
APPENDIX
D. TR-7190 Mechanical Drawings
This page is left blank.
76
TR-7190 User Manual