HP ProLiant BL460c Generation 5 (G5) Server Blade

QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Overview
1.
2.
3.
4.
HP ProLiant BL460c G5 Server Blade
Access Panel
5. Eight (8) PC2-5300, Fully Buffered DIMMs (DDR2-667)
Memory Slots
Up to two Quad-Core Intel® Xeon® 5000 Sequence
6. HP Smart Array E200i Controller with optional batteryprocessors
backed write cache (standard BTO models)
Small form factor (SFF) hot-plug drive bays (standard BTO
7. Two Mezzanine slots
models)
Local I/O connector
8. Internal USB Connector (standard BTO models)
What's New
Support for Hot Plug SAS Enterprise 300GB 3G SAS 10K SFF DP ENT Hard Drive
At A Glance
This document covers the HP ProLiant BL460c G5 server blade only. For more information on HP BladeSystems c-Class
Infrastructure and HP BladeSystem c-Class Interconnect Components, please see the following QuickSpecs:
HP BladeSystem c-Class Enclosures QuickSpecs:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_div/12810_div.html
HP BladeSystem c-Class Interconnect Components QuickSpecs:
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 1
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Overview
http://h18000.www1.hp.com/products/quickspecs/12524_div/12524_div.html
The HP ProLiant BL460c G5 provides greater 2P x86 server blade density without compromise and maximum power-efficiency with
flexibility and choice.
HP ProLiant BL460c G5 server blade includes:
Processor:
Up to two Quad-Core Intel® Xeon® 5400 Series processors
Supports up to 2 Quad-3.00 GHz 1333MHz-2x6 MB Level 2 cache memory
Intel 5000P chipset supporting up to a 1333 MHz Front Side Bus
Memory:
Up to 32GB Low Power(LP) memory, supported by (8) slots of PC2-5300 Fully Buffered DIMMs at 667 MHz
Supporting only low-power memory
Advanced ECC memory support
Supporting memory interleaving (2x1); memory mirroring and online spare capacity.
Storage Controller:
Integrated HP Smart Array E200i RAID controller with 64 MB cache (with optional battery-backed write-cache) with an
upgrade to 128 MB cache in standard BTO models. Supports RAID 0,1 in standard BTO models
Internal Drive Support:
Up to 2 small form factor (SFF) SAS or SATA hot plug hard disk drives in standard BTO models
Network Controller:
Two (2) embedded NC373i Multifunction Gigabit Server Adapters with iSCSI boot, TCP/IP offload engine, and
optional accelerated iSCSI
One (1) additional embedded 10/100 network adapter dedicated to iLO 2 management
NOTE: The Gigabit Ethernet adapters transmit from the server at 2000 Mbps only, full duplex per port. For more
information, see the "Network Controller" item in Standards Features section.
Mezzanine Support:
Two (2) additional I/O expansion slots via mezzanine card.
Supports up to two (2) mezzanine cards
Dual-Port Fibre Channel Mezzanine (4-Gb) options for SAN connectivity (Choice of Emulex or QLogic).
Wide variety of 10GbE and 1GbE network adapter options for additional network ports
QLogic QMH4062 Gigabit Ethernet iSCSI initiator
4X DDR InfiniBand (IB) Mezzanine (20 Gb/s) options for low latency server interconnectivity (based on Mellanox
technology
Internal USB Support:
One (1) internal USB 2.0 connector for security key devices and USB drive keys in standard BTO models
VMware ESX Server 3i and Citrix XenServer virtualization technology:
Integrated Hypervisors: (Optional)
VMware ESX Server 3i virtualization technology
Citrix XenServer virtualization technology
Form Factor:
HP ProLiant BL460c G5 server blade plugs vertically into the BladeSystem c3000 and c7000 enclosures
Management:
HP Integrated Lights-Out 2 (iLO 2) Standard Blade Edition with virtual KVM graphical remote console, with the option
to upgrade to the iLO Advanced for BladeSystem. iLO Advanced for BladeSystem is a no installation upgrade offering
automatic video footage of the events leading up to the server event (like bluescreens), automatic video footage of the
server blade's last boot sequence, on-demand video record and playback for training videos, team collaboration
features for up to four users on a single iLO session, and much more. Learn more at: www.hp.com/go/iLO.
Operating Systems:
Supports Windows, Linux, Netware, and Solaris Operating Systems
Enclosures:
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 2
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Overview
HP offers three different c-Class server blade enclosures to meet your individual needs:
The HP BladeSystem c7000 rack enclosure is 10U high and holds up to 16 ProLiant BL460c G5 servers plugged
vertically.
The HP BladeSystem c3000 rack enclosure is 6U high and holds up to 8 HP ProLiant BL460c G5 servers
plugged horizontally.
The HP BladeSystem c3000 tower enclosure is designed with casters for sites without racks and holds up to 8 HP
ProLiant BL460c G5 servers plugged vertically.
Server blades, storage blades, interconnect modules, power supplies, fans, and redundant Onboard Administrator
modules are all designed to fit into the c3000 and c7000 enclosures.
For additional enclosure information, please see: http://h18004.www1.hp.com/products/blades/components/enclosures/cclass/index.html.
Warranty:
This product is covered by a global limited warranty and supported by HP Services and a worldwide network of HP
Authorized Channel Partners. Hardware diagnostic support and repair is available for three years from date of
purchase. Support for software and initial setup is available for 90 days from date of purchase. Enhancements to
warranty services are available through HP Care Pack services or customized service agreements. Certain restrictions
and exclusions apply. SATA hard drives have a one year warranty. SAS drives have a 3 year warranty.
NOTE: Server warranty includes 3 year Parts, 3 year Labor, 3-year on-site support. Warranty repairs may be
accomplished through the use of Customer Self Repair (CSR) parts. These parts fall into two categories: 1) Mandatory
CSR parts are designed for easy replacement. A travel and labor charge will result when customers decline to replace a
Mandatory CSR part; 2) Optional CSR parts are also designed for easy replacement but may involve added complexity.
Customers may choose to have HP replace Optional CSR parts at no charge. Additional information regarding
worldwide limited warranty and technical support is available at:
http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 3
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
Processor
Quad-Core Processor Option Kits
Quad-Core Intel® Xeon® Processor E5450 (3.0 GHz, 1333 FSB, 80W)
Quad-Core Intel® Xeon® Processor L5430 (2.66 GHz, 1333 FSB, 50W)
NOTE: Intel 5400 Series processors are 64-bit and support Intel VT. Intel.
NOTE: For the Intel 5400 Series, the letter preceding the model number indicates the
performance/wattage of the processor. "X" denotes High Performance/Wattage; "E" denotes Enterprise
Performance/Wattage (Mainstream); and "L" denotes Lower Wattage.
Upgradeability
Upgradeable to 2 processors
Cache Memory
2 x 6 MB shared L2 cache (5400 Series)
Chipset
Intel® 5000P Chipset
Memory
Type
Standard
Maximum
Network Controller
Two (2) embedded NC373i Multifunction Gigabit Server Adapters with iSCSI boot, TCP/IP offload
engine, and optional accelerated iSCSI
One (1) additional 10/100 NIC dedicated to iLO 2 Management
NOTE: The Gigabit Ethernet adapters transmit from the server at 2000 Mbps, full duplex per port only.
However, within a Linux environment, the speed can be reduced or "throttled" using a feature available
within the Linux operating system; see the white paper at:
http://h71028.www7.hp.com/ERC/downloads/4AA1-5513ENW.pdf for more information.
PC2-5300 Fully Buffered DIMMs at 667 MHz
2 GB LP (2 x 1 GB)
32 GB LP (8 x 4 GB)
NOTE: This model only supports low power memory
Memory must be installed in pairs.
Once the adapter signal reaches the interconnect within the blade enclosure and communicates outside
the blade enclosure to the LAN, the blade interconnect uplink types and settings determine the cable
media, speed, duplex mode, and auto negotiation mode. Interconnects are available with Ethernet
uplinks supporting 10/100/1000T, 10/100/1000 SFP, 1000 SX fiber, and 10Gb KX-4.
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 4
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
Multifunction Networking The embedded multifunction NC373i adapters combine standard Gigabit Ethernet networking, TCP/IP
offload engine (TOE), iSCSI boot and optional accelerated iSCSI into a single adapter.
TOE moves the processing of data in the TCP protocol stack from the server CPU to the network
card, freeing CPU cycles for other activities. With TOE, network communications are improved,
and server efficiency is increased. The NC373i offers TOE for Microsoft® Windows 2000 and
2003 environments.
The iSCSI network boot (iSCSI boot) allows the BL460c G5 to boot from a remote operating
system (OS) image located on a storage area network (SAN). The BL460c G5 uses an iSCSI
firmware image (iSCSI boot option ROM) making the remote disk drive appear as a local,
bootable C: drive. The BL460c G5 is configured to connect to and boot from the iSCSI target disk
on the network and download the OS image from the iSCSI target disk. The iSCSI boot option
ROM is supplied by HP at no cost. The additional cost and mezzanine slot usage of an add-in
iSCSI HBA card is not required. Additionally, the HP iSCSI boot solution includes scripts to
significantly simplify the installation process.
I/O Expansion Slots
Two I/O expansion mezzanine slots (one x8 and one x4)
Integrated Manageability Integrated Lights-Out 2 (iLO 2) Standard Blade Edition (integrated on motherboard)
Storage Controller
HP Smart Array E200i
Controller
64 MB memory module supports RAID 0,1
Available upgrades: 128 MB with Battery-backed write cache
Maximum Internal
Storage
Hot Plug SAS
Hot Plug SATA
600GB
500GB
Graphics
Integrated ATI RN-50 1600x1280x64K 16M color (32 MB DDR1 memory)
Graphics Resolution
Supported
Resolution Color Depths
DA - 13166
2 x 300GB Serial SCSI
2 x 250GB Serial ATA
1600 x 1280, 64K, 256, 16
1280 x 1024, 16.7M, 64k, 256, 16
1024 x 768, 16.7M, 64k, 256,16
800 x 600, 16,7M, 64k, 256, 16
640 x 480, 16,7M, 64k, 256, 16
Worldwide — Version 3 — December 15, 2008
Page 5
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
Fibre Channel Support
Two optional Fibre Channel HBAs are supported by the HP ProLiant BL460c G5. Both mezzanine circuit
boards connect directly to the server blade system board. These Fibre Channel HBAs are available via
option kits and must be ordered separately.
Two option kits
Emulex LPe1105-HP 4Gb FC HBA for HP c-Class BladeSystem (403621-B21)
Based on the same field-proven ASIC, firmware, and driver technology as Emulex's renowned
LPe1150 HBA, the Emulex LPe1105-HP is fully driver compatible with all Emulex HBAs
QLogic QMH2462 4Gb FC HBA for HP c-Class BladeSystem (403619-B21)
Uses common drivers which means that customers can standardize on one QLogic driver whether
they are using the QMH2462 or other 4Gb and 2Gb HBAs powered by QLogic
Emulex and QLogic Fibre Channel HBAs feature:
Optimal performance utilizing PCI Express
4/2/1Gb/s auto negotiating speeds
Dual-ports for redundant path connections
Up to two FC HBAs per server blade providing redundant FC HBA support
Optimized for HP StorageWorks and supported by third party SAN vendors
Support for Microsoft® Windows® and Linux operating systems environments
Compatible SAN
HP ProLiant BL460c G5 server blades are optimized for HP StorageWorks MSA, EVA and XP
HP ProLiant 460c G5 server blades are compatible with select 3rd party SANs (please see blade storage
page for more details: http://h18000.www1.hp.com/products/servers/proliant-bl/c-class/storage.html
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 6
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
Insight Control
Environment for
BladeSystem
Management Suite
Insight Control Environment for BladeSystem delivers foundation management for HP BladeSystem
lifecycles, including hardware resource deployment, health monitoring, software version control,
performance monitoring, vulnerability, scanning and patch management and power management.
HP Control Insight Environment for BladeSystem installs and licenses the following components by
default using a wizard-based integrated installer:
HP Systems Insight Manager
HP iLO Select Pack
HP Insight Power Manager
HP ProLiant Essentials Rapid Deployment Pack
HP ProLiant Essentials Performance Management Pack
HP ProLiant Essentials Vulnerability and Patch Management Pack
HP ProLiant Essentials Virtual Machine Management Pack
Additional ProLiant Essentials software and management tools included on the Insight Control
Management kit can be installed manually.
HP Server Migration Pack - Universal Edition
NOTE: HP Server Migration Pack - Universal Edition is licensed separately from the Insight
Control Environment Suite.
HP Open Service Event Manager
HP Instant Support Enterprise Edition
NOTE: HP Server Migration Pack - Universal Edition can be installed from the SMP-Universal CD
included in the Insight Control Management media kit.
NOTE: Insight Control Environment for BladeSystem can be installed from the Insight Control
Management DVD, which can be delivered with HP BladeSystem c-Class enclosures with a choice of
licensing options. Licensing options include a free 30 day evaluation license for 8 servers (default option
for every enclosure order), a full purchased license for 8 blade servers or a full purchased license for 16
blade servers). For additional information on HP c-Class Infrastructure please visit HP BladeSystem cClass Enclosures QuickSpecs:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_div/12810_div.html
NOTE: For additional product and licensing information about Insight Control Environment for
BladeSystem, HP Systems Insight Manager and Essentials software refer to:
http://www.hp.com/servers/proliantessentials.
HP Insight Control Environment for Linux (ICE-Linux) provides comprehensive discovery, imaging &
deployment, monitoring, and management for Linux-based ProLiant server platforms. Built on the
industry-leading HP Systems Insight Manager framework, this solution integrates open source technology
with experience leveraged from HP's Linux products in HP ICLE and HP XC Clusters, while providing
paths to the future with developing management technologies.
iLO Power Management Pack for BladeSystem is energy-efficient management software that delivers
centralized control, reliable security, and energy savings for your BladeSystem infrastructure. iPMP
combines the total control of iLO 2 Advanced in the area of remote management with the energy
monitoring and control of the Insight Power Manager to deliver a robust solution capable of full remote
control and power management of ProLiant servers through a unified interface within HP Systems Insight
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 7
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
Manager.
HP Insight Control management suites and most HP ProLiant Essentials include one year of 24 x 7 HP
Software Technical Support and Update Service ensuring rapid access to HP support staff and proactive
delivery of software updates. From more information about this service, please visit:
http://www.hp.com/services/insight.
Server Management
Stand Alone Software
Product - ProLiant
Essentials
HP Systems Insight
Manager
HP Systems Insight Manager (HP SIM) provides a unified, secure and
extensible standards-based environment to centrally manage servers, storage
and other infrastructure devices, (both HP and non-HP) across multiple
operating system platforms.
iLO Advanced Pack
Upgrades the iLO 2 processor with comprehensive remote control including
Virtual KVM remote graphical console, enhanced console sharing and
replay, virtual media (floppy, CD/DVD, USB key), virtual folders, and
enterprise security (directory services and two-factor authentication).
iLO Advanced for
Upgrades the iLO 2 processor with enhanced console sharing and replay,
BladeSystem
virtual media (floppy, CD/DVD, USB key), virtual folders, historical power
reporting, power capping and enterprise security (directory services and twofactor authentication) for servers managed using remote consoles available
in iLO 2 Standard Blade Edition.
ProLiant Essentials Rapid Rapid Deployment Pack (RDP) extends HP Systems Insight Manager with a
Deployment Pack
complete deployment solution for HP ProLiant blade servers. RDP provides a
central location to configure server hardware, deploy Windows, Linux and
VMware ESX operating environments and install HP ProLiant Support Pack
drivers using images and scripted profiles.
Insight Power Manager
Upgrades the single-server remote management capabilities of iLO
(IPM)
Select/Advanced to include centralized reporting and policy-based
management of power consumption and thermal output provided by the
Insight Power Manager. IPM unifies all of this functionality within a single
user interface - HP Systems Insight Manager.
HP Insight Dynamics - VSE Introducing HP Insight Dynamics - VSE, the world's first software integrated by
design to let IT professionals analyze and optimize their virtual & physical
environments in the same way. It combines the best of the industry-leading
HP infrastructure management portfolio-including HP Systems Insight
Manager, HP Insight Control and HP Virtual Server Environment-into one
integrated offering for HP BladeSystem, ProLiant and Integrity servers.
NOTE: For more information, visit: http://www.hp.com/go/insightdynamics
ProLiant Essentials Server Upgrading, replacing, or virtualizing your existing server? Effortlessly
Migration Pack - Universal transition to new virtual or physical HP ProLiant servers or BladeSystem with
Edition
automated, accurate and affordable migration of OS, application and data.
SMP Universal automates the manual processes required for migrating
servers between physical or virtual platforms, whether migrating to VMware
or Microsoft virtual machines. SMP Universal allows all of the following
migrations:
physical to ProLiant
physical to virtual
virtual to virtual
virtual to ProLiant
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 8
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
NOTE: For more information, visit: http://www.hp.com/go/migrate.
ProLiant Essentials
Performance Management Pack (offered exclusively through the Insight
Performance Management Control suites) - a performance management solution that identifies and
Pack
explains hardware performance bottlenecks on ProLiant servers and attached
options enabling users to better utilize their valuable resources
The Vulnerability and
Vulnerability and Patch Management Pack (offered exclusively through the
Patch Management Pack Insight Control suites) - identifies and remediates software security
vulnerabilities due to missing patches as well operating system configurations
that can be exploited by viruses, worms, and other blended threats.
Virtual Machine
Virtual Machine Management Pack - provides central management and
Management Pack
control of virtual machines from Microsoft and VMware. Integrated approach
provides the ability to manage both physical and virtual resources from a
single management console.
NOTE: Flexible and volume quantity license kits are available for ProLiant
Essentials Value Packs. Refer to: http://www.hp.com/go/proliantessentials or
the various ProLiant Essentials Value Pack product QuickSpecs for more
information.
Core Infrastructure
Management
SmartStart
Insight Management
Agents
SmartStart is a tool that simplifies server setup, providing a rapid way to
deploy reliable and consistent server configurations. For more information,
please visit the SmartStart Web site at:
http://www.hp.com/servers/smartstart.
SmartStart version supported (minimum): SmartStart 7.60
The Insight Management Agents should be installed on all HP servers to
present system instrumentation, health and configuration information into HP
Systems Insight Manager and the HP System Management Homepage. The
HP System Management Homepage aggregates systems data from Insight
Management Agents and other HP management tools, providing a
consolidated browser-based interface for managing individual servers.
Insight Management Agents and The HP System Management Homepage
are included on ProLiant Support Packs, and can also be installed using the
server profiles provided with the ProLiant Essentials Rapid Deployment Pack.
Subscriber's Choice
ProLiant Support Packs
and ROMPaq, software
DA - 13166
For additional information about the Management Agents and the HP System
Management Homepage please visit the management Web site at:
http://www.hp.com/servers/manage.
Subscriber's Choice Driver and Support Alerts/Notifications is a web-based
email subscription service that provides software and driver change
notifications for ProLiant products. Sign up at:
http://www.hp.com/go/subscriberschoice
and customize your profile to receive various new alerts as they become
available, on a weekly or monthly basis.
The latest software, drivers, and firmware fully optimized and tested for your
ProLiant server and options, available through ProLiant Support Packs the
ProLiant Essentials Rapid Deployment Pack, SmartStart or downloaded from
software and drivers download pages website at:
http://www.hp.com/go/support.
Worldwide — Version 3 — December 15, 2008
Page 9
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
HP Serviceguard for Linux HP Serviceguard for Linux is a high availability clustering solution designed to protect applications and
(SGLX)
services from a wide variety of software and hardware failures, monitoring the health of each server
(node) and quickly responding to failures such as those that affect system processes, system memory,
LAN media and adapters, and application processes.
The following is a quick summary of HP Serviceguard for Linux features and support. For the most recent
list of Linux distributions & kernels, servers and storage supported with Serviceguard for Linux, see the
Serviceguard for Linux Datasheet, available at: http://www.hp.com/go/sglx/info.
Supported Linux Distributions:
Red Hat EL 4
Red Hat EL 5
SUSE SLES10
Supported Server Platforms
HP Integrity BladeSystem to Superdome
HP ProLiant BladeSystem p-Class & c-Class
HP ProLiant DL
HP ProLiant ML
IBM System x
Dell PowerEdge
Sun x64
Fujitsu Siemens PRIMERGY
Supported Virtual Machines
SG/LX in HP Integrity Virtual Machines guests
SG/LX in VMware ESX guests
SG/LX in Red Hat and SUSE Xen hosts (DOM0)
Application Integration Toolkits
HP Serivceguard for Linux Oracle Database Toolkit
HP Serviceguard Extension for SAP on Linux (SGeSAP/LX)
Free Application Integration Toolkits:
Apache
MySQL
NFS
PostgreSQL
Samba
Tomcat
Sendmail
Disaster Tolerant Solutions
HP Serviceguard for Linux Extended Distance Cluster (XDC) extends cluster distances up to
100 km, utilizes software RAID mirroring for data replication and is storage array
independent
HP StorageWorks XP/EVA Cluster Extension Software for Linux (CLX) works seamlessly with
HP Serviceguard for Linux, HP StorageWorks Continuous Access, and HP Disk Arrays to
automate failover and failback between sites
Software updates are distributed by HP Services to customers with support contracts
NOTE: The above is not a complete list of all HP Serviceguard for Linux product numbers. For a detailed
list of supported configuration/certification options for HP Serviceguard for Linux, please refer to the HP
Serviceguard for Linux Configuration & Ordering Guide available at: http://www.hp.com/go/sglx/info.
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 10
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
OS Support
Microsoft Windows Server 2003 R2
Microsoft Windows Server 2008
Microsoft Windows Small Business Server 2003 R2
Red Hat Enterprise Linux
SUSE Linux Enterprise Server
Sun Solaris for x64/x86-based Systems
VMware
NOTE: For more information on HP's Certified and Supported ProLiant Servers for OS and Virtualization
Software and latest listing of software drivers available for your server, please visit our Support Matrix at:
http://www.hp.com/go/supportos.
Integrated Manageability iLO 2 Advanced for BladeSystem (integrated on motherboard)
Graphical Remote Console
New iLO Text Console
Measure, regulate, and cap server power consumption
Automatically captured video footage of last boot sequence
Automatically captured video footage of last fault sequence (such as blue screen)
On-Demand video recording for training or quality assurance needs
Global team collaboration for up to four remote users
Virtual media and folders (no ISO or floppy image needed)
LDAP integration
MS Terminal Services Pass-through
Remote Serial Console
Virtual Power Button Control
Plus all capabilities of iLO 2 Standard Blade Edition
Integrated Lights-Out 2 Standard Blade Edition (iLO 2)
Graphical Remote Console
Virtual media (single server, browser based access only)
Remote Serial Console
OS independent hardware health status
NOTE: For more information on HP Integrated Lights-Out, visit: www.hp.com/go/iLO.
Availability
Dual-Port Fibre Channel Mezzanine Card for redundant SAN connection
Two (2) embedded Gigabit Ethernet adapters for redundant LAN connections Two (2) hot-plug
SAS/SATA hard drive bays and integrated RAID (HP Smart Array E200i) controller on every BTO
model server blade (Battery-backed write cache is optional.)
Redundant ROM on each server blade
Advanced ECC Memory - can correct a multi-bit error (up to 4 bits) that occurs within one
memory chip
Memory Mirroring
Memory Online Spare Capacity
Network adapter teaming (network fault tolerance, transmit load balancing, switch-assisted load
balancing)
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 11
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
Industry Standard
Compliance
Security
Factory Express Portfolio
for Servers and Storage
ACPI 2.0 Compliant
PCI 2.2 Compliant
WOL Support
Microsoft® Logo certifications
USB 2.0 Support
One (1) internal USB 2.0 connector for security key devices and USB drive keys on every BTO
model server blade Power-on password
Administrator's password
Integrated Lights-Out 2 has 12 customizable user accounts and SSL encryption
Integrated Lights-Out 2 can be disabled via a Global Setting
HP Factory Express offers configuration, customization, integration and deployment services for HP
servers and storage products. Customers can choose how their factory solutions are built, tested,
integrated, shipped and deployed.
Factory Express offers service packages for simple configuration, racking, installation, complex
configuration and design services as well as individual factory services, such as image loading, asset
tagging, and custom packaging. HP products supported through Factory Express include a wide array of
servers and storage: HP Integrity, HP ProLiant, HP ProLiant Server Blades, HP BladeSystem, HP 9000
servers as well as the MSAxxxx, VA7xxx, EVA, XP, rackable tape libraries and configurable network
switches.
For more information on Factory Express services on your specific server model please contact your sales
representative or go to: http://www.hp.com/go/factory-express.
HP Enterprise
Configurator
The HP e-Configure Enterprise Configurator now provides factory default racking for our HP hardware
portfolio. This approach is aligned with our strategic direction to meet the needs and expectations of our
valued customers. If you require "custom" rack configuration, please contact HP's Customer Business
Center or an Authorized Partner for assistance.
NOTE: This feature is not supported in the NEW Drive-less model which is available through CTO for
those who do not utilize internal hard disk drives and attach to SAN.
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 12
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Standard Features
Service and Support
HP Care Pack services provide total care and support expertise with committed response designed to
meet your IT and business needs.
The HP Care Pack service for HP ProLiant BL c-Class server blades, cover the server blade and all HP
branded hardware options qualified for the server, purchased at the same time or afterwards, internal to
the server.
To fully capitalize on your HP BladeSystem servers' capabilities requires a service partner who thoroughly
understands your server technology and systems environment. HP Services, an industry leader in
provision of multi vender support solutions provides a range of support services designed to meet the
varying needs of business. Whether an SMB or large global corporation HP has a HP BladeSystem server
support offer to help you speedily deploy and maximize system uptime.
Recommended Service - Simplify ProLiant solution implementation, maintenance and management.
Support Service - 4-Hour Response Coverage, 3-Year, 24 x 7, Same Business Day
Deployment Service - Installation and Start Up for HP BladeSystem Infrastructure
Enhanced Service - Optimize service level to increase IT performance and availability
Support Service - HP Proactive BladeSystem Service, 1-Year
Deployment Service - Enhanced Network Installation and Start-up for HP BladeSystem Switches
Installation & Start-Up service for HP BladeSystem Infrastructure plus HP BladeSystem Enhanced Network
Installation and Start-UP as per the Customer Description and/or Data Sheet. To be delivered on a
scheduled basis 8am-5pm, M-F, excluding HP holidays.
For a complete listing of service offerings and information visit:
http://www.hp.com/services/bladesystemservices
http://www.hp.com/go/proliant/carepack
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 13
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Models
Quad-Core Models
HP BL460c G5 E5450
2G LP (1P)
501713-B21
HP BL460c G5 L5430
2G LP (1P)
492310-B21
Processor(s)
One of the following
depending on model
Cache Memory
Memory
Network Adapter
Storage Controller
Hard Drives
Internal Storage
Optical Drive
Form Factor
DA - 13166
(1) Quad-Core Intel® Xeon® Processor E5450 (3.0 GHz, 1333 FSB, 80W)
(1) Quad-Core Intel® Xeon® Processor L5430 (2.66 GHz, 1333 FSB, 50W)
2 x 6 MB Level 2 cache (5400 Series)
2 GB (2 x 1 GB) PC2-5300, FBD DDR2-667, Low Power
Two (2) embedded NC373i Multifunction Gigabit Server Adapters plus one
(1) additional 10/100 network adapter dedicated to iLO 2 Management
HP Smart Array E200i Controller with 64MB (optional battery-backed write
cache)
No drives included; (2) SFF SAS/SATA drive bays
SAS: 600GB
SATA: 500GB
None
Up to 8 half-height blades supported in HP BladeSystem c3000 Enclosure
Up to 16 half-height blades supported in HP BladeSystem c7000 Enclosure
Worldwide — Version 3 — December 15, 2008
Page 14
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Configuration Information - Factory Integrated Models
NOTE: This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are
ordered, HP recommends the use of an HP approved configurator. Contact your local sales representative for information on CTO
product offerings and requirements.
NOTE: HP does not allow factory integration of options into standard models listed above.
Configure-to-order server blades must start with a CTO Blade.
NOTE: This product offering does not support HP Factory Express Server Configuration Level 1.
NOTE: FIO indicates that this option is a Factory Installable Option.
Step 1: Base Server Blade Configuration (Select a configurable Blade)
Models
HP ProLiant BL460c G5 CTO Blade
Configurable Model ships with:
Two (2) embedded NC373i Multifunction Gigabit Server Adapters, Hard Disk Drive
Backplane with USB connector, plus one (1) additional 10/100 NIC dedicated to iLO
2 Management
Integrated Lights-Out 2 Standard Blade Edition
501715-B21
Step 2: Choose Required Options (one of the following from each list unless otherwise
noted):
Processors
Memory
For single processor configuration choose:
Quad-Core Processor Option Kits
Quad-Core Intel® Xeon® processor E5450 (3.00 GHz, 1333 FSB, 80 W) Option
Kit, FIO Base
NOTE: If 2 processors are desired, select one 459489-L21 and one 459489-B21.
Quad-Core Intel® Xeon® processor L5430 (2.66 GHz, 1333 FSB, 50 W) Option Kit,
FIO Base
NOTE: If 2 processors are desired, select one 493764-L21 and one 493764-B21.
2 GB FBD PC2-5300 (2 x 1 GB LP) Kit
4 GB FBD PC2-5300 (2 x 2 GB LP) Kit
8 GB FBD PC2-5300 (2 x 4 GB LP) Kit
NOTE: Memory Option Kits described as LP include Low Power DIMMs. For more
information on ProLiant Energy Efficient Features, see:
http://h18004.www1.hp.com/products/servers/platforms/energyefficient/
NOTE: Must be installed in pairs
DA - 13166
Worldwide — Version 3 — December 15, 2008
459489-L21
493764-L21
461826-B21
461828-B21
466440-B21
Page 15
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Configuration Information - Factory Integrated Models
Step 3: Choose Additional Factory Integratable Options (one of the following from each list
unless otherwise noted):
VMware ESX Server 3i
integrated hypervisor
Citrix XenServer
integrated hypervisor
Controller Cache
VMware ESX Server 3i 2P integrated hypervisor, FIO
VMware ESX Server 3i VI3 Enterprise 2P integrated hypervisor, FIO
NOTE: For additional information and option kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12307_div/12307_div.html
(Worldwide)
Integrated XenServer HP Select Edition 2P/4P
Integrated XenServer HP Enterprise Edition 2P/4P
NOTE: For additional information and option kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/13018_div/13018_div.html
(Worldwide)
464668-B21
464669-B21
64 MB Cache - FIO Only
NOTE: Integrated HP Smart Array E200i RAID controller supporting RAID 0/1
Controller cache module selection is required for all blades that support hard disk
drives. Select either the standard 64 MB module above or the optional 128 MB
module below.
128 MB Battery-Backed Cache Enabler
NOTE: Supports the HP Smart Array E200i Controller.
405102-B21
464673-B21
464674-B21
351580-B21
Step 4: Choose Additional Options for Factory Integration
NOTE: For additional options, including server blade enclosures interconnect options and power subsystem options; please see the
options section below; or the following QuickSpecs:
HP BladeSystem c-Class Enclosures QuickSpecs:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_div/12810_div.html
and HP BladeSystem c-Class Interconnect Components QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12524_div/12524_div.html.
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 16
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Options
Ethernet Mezzanine
Options
HP NC325m PCI Express Quad Port 1Gb Server Adapter for c-Class BladeSystem
NOTE: If the NC325m is installed in mezzanine slot 1 of a half-height server,
connectivity will be provided on 2 of the 4 ports.
HP NC326m PCI Express Dual Port 1Gb Server Adapter for c-Class BladeSystem
HP NC360m Dual Port 1GbE BL-c Adapter
HP NC364m Quad Port 1GbE BL-c Adapter
NOTE: If the NC364m is installed in mezzanine slot 1 of a half-height server,
connectivity will be provided on only 2 of the 4 ports.
HP NC373m PCI Express Dual Port Multifunction Gigabit Server Adapter for c-Class
BladeSystem
HP NC382m Dual Port 1GbE Multifunction BL-c Adapter
NOTE: The Gigabit Ethernet adapters above transmit from the server at 2000 Mbps,
full duplex per port only. For more information, see the "Network Controller" segment
in the Standards Features section.
HP NC512m Dual Port 10GbE Multifunction BL-c Adapter
NOTE: The NC512m is supported in type II x8 PCI Express mezzanine slots;
maximum two adapters per server. For more information, see the Mezzanine Slot
Compatibility matrix within the HP NC512m Dual Port 10GbE Multifunction BL-c
Adapter QuickSpecs:
http://h18004.www1.hp.com/products/servers/networking/nc512m/index.html.
NOTE: A minimum of 2 GB of server memory is required per NC512m and supports
a maximum of 32 GB for Windows and 64 GB for Linux.
NOTE: The NC512m adapter transmits from the server only at 20 Gbps, full duplex
per port.
HP NC532m Dual Port 10GbE BL-c Adapter
NOTE: The NC532m network adapter card is required for each server blade
connecting to a 10Gb interconnect in bays 3-8 (HP BladeSystem c7000 Enclosure) or
bays 3-4 (HP BladeSystem c3000 Enclosure).
NOTE: The NC532m requires a minimum of 2 GB of server memory.
NOTE: The NC532m will downspeed to 1Gb if paired with a 1Gb interconnect.
QLogic QMH4062 1Gb E iSCSI Adapter for HP BladeSystem c-Class
416585-B21
406771-B21
445978-B21
447883-B21
406770-B21
453246-B21
440910-B21
467799-B21
488074-B21
Fiber Channel Mezzanine Emulex LPe1105 FC Dual Channel 4Gb, PCI-E-to-Fibre Channel Host Bus Adapter
Options
QLogic QMH2462 4Gb FC HBA for HP c-Class BladeSystem
403621-B21
403619-B21
HP InfiniBand Mezzanine HP 4X DDR IB Dual Port Mezzanine HCA for HP BladeSystem c-Class
Options
HP 4X DDR IB Mezzanine HCA for HP BladeSystem c-Class
448262-B21
410533-B21
HP StorageWorks SB40c HP StorageWorks SB40c Storage Blade
Storage Blade
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12587_div/12587_div.html
(Worldwide)
411243-B21
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 17
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Options
HP PCI Expansion Blade
HP PCI Expansion Blade
NOTE: Ships with one pre-installed PCI-X connect board. Also includes one PCIe
connect board which requires installation.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12753_div/12753_div.html
HP c-Class Tape Blades
HP StorageWorks SB920c Tape Blade
NOTE: LTO-3 Ultrium technology.
HP StorageWorks Ultrium 448c Tape Blade
NOTE: LTO-2 Ultrium technology.
448018-B21
AJ401A
440947-B21
NOTE: The HP PCI Express Mezzanine Pass-Thru Card for HP BladeSystem (431643B21) is required when installing a tape blade adjacent to a full-height server blade.
NOTE: Please see the QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12729_div/12729_div.html
HP Insight Control
Environment for
BladeSystem
Management Suite
NOTE: Electronic licensing options are available for Insight Control suites software
products. Please see the appropriate Insight Control QuickSpecs for additional
information.
Insight Control Environment for BladeSystem
HP Insight Control Environment for BladeSystem, No Media 1-Server License including
1 year of 24x7 Technical Support and Updates
NOTE: Customer will receive a printed license entitlement certificate via physical
shipment. The license entitlement certificate must be redeemed online or via fax in
order to obtain the license activation key(s). Includes one year of 24 x 7 HP Software
Technical Support and Update Service.
HP Insight Control Management Software Media Kit
NOTE: Insight Control Management DVD media without licenses. Contains Insight
Manager and Essentials software products and components licensed by Insight
Control Management suites. Uses an integrated installer to perform quick and
accurate software installation and updates.
NOTE: For additional License Kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12631_div/12631_div.html
HP Insight Control Environment for Linux
HP Insight Control Linux Edition, No Media, 1-Server License including 1 year of 24x7
Technical Support and Updates
NOTE: This part number can be used to purchase one (1) license with a single
activation key. Customer will receive a printed license entitlement certificate via
physical shipment. The license entitlement certificate must be redeemed online or via
fax in order to obtain the license activation key(s). Includes one year of 24 x 7 HP
Software Technical Support and Update Service. One certificate is shipped for each
license.
HP Insight Control Linux Edition Media Only Kit
NOTE: This optional Media pack CD contains the ISO image for HP Insight Control
Environment for Linux, HP System Insight Manager, and an integrated installer. Servers
must be acquired separately.
This Media pack is optional because the latest ISO image and latest updates may be
DA - 13166
Worldwide — Version 3 — December 15, 2008
453484-B21
436222-B21
464423-B21
464422-B21
Page 18
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Options
downloaded at no cost from: http://www.hp.com/go/ice-linux (click on Download
button).
NOTE: For additional License Kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/13019_div/13019_div.html
HP iLO Power Management Pack for BladeSystems
HP iLO Power Management Pack for BladeSystem, No Media, 1-Server License
including 1 year of 24x7 Technical Support and Updates
NOTE: This option kit includes 1 license for iLO Select and Insight Power Manager.
Customer will receive a printed license entitlement certificate via physical shipment.
The license entitlement certificate must be redeemed online or via fax in order to
obtain the license activation key(s). Includes one year of 24 x 7 HP Software Technical
Support and Update Service.
NOTE: For additional License Kits please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12632_div/12632_div.html
Server Management
Stand Alone Software
Product - ProLiant
Essentials
NOTE: Electronic licensing options are available for Insight Control suites and select
ProLiant Essentials software products. Please see the appropriate Insight Control and
ProLiant Essentials QuickSpecs for additional information.
Deploy
Rapid Deployment Pack
ProLiant Essentials Rapid Deployment Pack No Media 1-Server License including 1
year of 24x7 Technical Support and Updates
NOTE: This license allows 1 server to be deployed and managed via RDP. Customer
will receive a printed license entitlement certificate via physical shipment. The license
entitlement certificate must be redeemed online or via fax in order to obtain the
license activation key(s). Includes one year of 24 x 7 HP Software Technical Support
and Update Service.
NOTE: For additional License Kits- please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/11053_div/11053_div.html
HP Server Migration Pack - Universal Edition
HP Server Migration Pack - Universal Edition, No Media, Physical / Virtual to ProLiant
Single Migration License, including 1 year of 24x7 Technical Support
NOTE: This license allows 1 physical to ProLiant or virtual to ProLiant migration.
Customer will receive a printed license entitlement certificate and documentation via
physical shipment. The license entitlement certificate must be redeemed online or via
fax in order to obtain the license activation key(s). Includes one year of 24 x 7 HP
Software Technical Support Service.
HP Server Migration Pack - Universal Edition, No Media, Physical / Virtual to Virtual
Single Migration License, including 1 year of 24x7 Technical Support
NOTE: This license allows 1 physical to virtual or virtual to virtual migration.
Customer will receive a printed license entitlement certificate and documentation via
physical shipment. The license entitlement certificate must be redeemed online or via
fax in order to obtain the license activation key(s). Includes one year of 24 x 7 HP
Software Technical Support Service.
HP Server Migration Pack - Universal Edition, No Media, 1-Year Unlimited Migration
License, including 1 year of 24x7 Technical Support
NOTE: This license allows unlimited migrations (physical to ProLiant, physical to
virtual, virtual to virtual, and virtual to ProLiant) for one year. Customer will receive a
DA - 13166
Worldwide — Version 3 — December 15, 2008
442937-B21
452151-B21
460750-B21
460753-B21
460756-B21
Page 19
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Options
printed license entitlement certificate and documentation via physical shipment. The
license entitlement certificate must be redeemed online or via fax in order to obtain
the license activation key(s). Includes one year of 24 x 7 HP Software Technical
Support Service.
NOTE: For additional License Kits please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12855_div/12855_div.html
Monitor
HP Insight Dynamics-Virtual Server Environment
HP Insight Dynamics-VSE without Insight Control Environment, 1-server license
including 1 year of 24x7 Technical Support and Updates
NOTE: This license supports HP ProLiant ML/DL and c-Class Blade servers. Customer
will receive via email a receipt and link to a license entitlement certificate.
HP Insight Dynamics-VSE with Insight Control Environment, 1-server license including
1 year of 24x7 Technical Support and Updates
NOTE: This license supports HP ProLiant c-Class Blade servers. Customer will receive
a printed license entitlement certificate via physical shipment.
NOTE: For additional license kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/13050_div/13050_div.html
Control
HP iLO Advanced Pack for BladeSystem
HP ProLiant Essentials Integrated Lights-Out Advanced for BladeSystem, No Media, 1Server License, including 1 year of 24x7 Technical Support and Updates
NOTE: For additional License Kits, please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12362_div/12362_div.html
Featuring: Sophisticated remote control and security features for HP BladeSystem
servers and ProLiant ML/DL servers.
NOTE: For additional License Kits please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12362_div/12362_div.html
Optimize
HP Insight Power Manager (IPM)
HP Insight Power Manager, No Media, 1-Server License, including 1 year of 24x7
Technical Support and Updates
NOTE: Customers purchasing this upgrade must already have an iLO Advanced or
Select license on each managed server. Customer will receive a printed license
entitlement certificate via physical shipment. The license entitlement certificate must be
redeemed online or via fax in order to obtain the license activation key(s). Includes
one year of 24 x 7 HP Software Technical Support and Update Service.
NOTE: For additional License Kits please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12623_div/12623_div.html
ProLiant Essentials Virtual Machine Management Pack
ProLiant Essentials Virtual Machine Management Pack, No Media, 1-Server License,
including 1 year of 24x7 Technical Support and Updates
NOTE: Customer will receive a printed license entitlement certificate via physical
shipment. The license entitlement certificate must be redeemed online or via fax in
order to obtain the license activation key(s). Includes one year of 24 x 7 HP Software
Technical Support and Update Service.
NOTE: For additional License Kits please see the QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/12328_div/12328_div.html
DA - 13166
Worldwide — Version 3 — December 15, 2008
483531-B21
483534-B21
512488-B21
452677-B21
452153-B21
Page 20
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Options
NOTE: Flexible and volume quantity license kits are available for ProLiant Essentials
Value Packs. Refer to: http://www.hp.com/servers/proliantessentials or the various
ProLiant Essentials Value Pack product QuickSpecs for more information.
Processors
Memory
Hard Drives
Quad-Core Process Option Kits
Quad-Core Intel® Xeon® processor E5450 (3.00GHz 1333 FSB, 80 W)
Quad-Core Intel® Xeon® processor L5430 (2.66 GHz, 1333 FSB, 80 W)
459489-B21
493764-B21
2 GB FBD PC2-5300 2 x 1 GB Low Power Kit
4 GB FBD PC2-5300 2 x 2 GB Low Power Kit
461826-B21
461828-B21
8 GB FBD PC2-5300 2 x 4 GB Low Power Kit
NOTE: Memory Option Kits described as LP include Low Power DIMMs. For more
information on ProLiant Energy Efficient Features, see:
http://h18004.www1.hp.com/products/servers/platforms/energyefficient/
NOTE: Must be installed in pairs.
466440-B21
SAS Hot Plug SFF Enterprise (ENT) Drives
HP 300GB 3G SAS 10K SFF DP HDD
HP 146GB 3G SAS 10K SFF DP HDD
HP 146GB 3G SAS 10K SFF SP HDD
HP 72GB 3G SAS 15K SFF DP HDD
HP 72GB 3G SAS 15K SFF SP HDD
HP 72GB 3G SAS 10K SFF DP HDD
HP 72GB 3G SAS 10K SFF SP HDD
HP 36GB 3G SAS 15K SFF DP HDD
HP 36GB 3G SAS 15K SFF SP HDD
NOTE: SAS drives have a 3 year warranty.
NOTE: Please see QuickSpecs for Technical Specifications and additional
information:
http://h18000.www1.hp.com/products/quickspecs/12244_div/12244_div.html
(Worldwide)
NOTE: The hard drive options are not required when configuring a Drive-less Model.
SATA SFF Hot Plug Entry (ETY) Drives
HP 250GB 3G SATA 5.4K SFF ETY HDD
HP 120GB 1.5G SATA 5.4K SFF ETY HDD
NOTE: SATA drives have a 1 year warranty. Please see the QuickSpecs for Technical
Specifications and additional information:
http://h18000.www1.hp.com/products/quickspecs/13021_div/13021_div.html
(Worldwide)
DA - 13166
Worldwide — Version 3 — December 15, 2008
492620-B21
418367-B21
431958-B21
418371-B21
431935-B21
384842-B21
375861-B21
418369-B21
431933-B21
460355-B21
458924-B21
Page 21
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Options
Controller Cache
128MB Battery-Backed Cache Enabler
NOTE: Supports the HP Smart Array E200i Controller.
NOTE: This option is not required when configuring a Drive-less Model.
High Availability Cluster
Options
HP Serviceguard for Linux
HP Serviceguard Linux for HP ProLiant/x86 Servers
Licensed per physical server
Includes media and One Year 24x7 Software Support & Updates
HP Serviceguard Linux Oracle Database Toolkit for HP ProLiant/x86 Servers
Licensed per cluster
Includes media and One Year 24x7 Software Support & Updates
USB Options
351580-B21
463831-B21
463833-B21
HP Serviceguard Extension for SAP on Linux for HP ProLiant/x86 Servers
Licensed per physical server
Includes media and One Year 24x7 Software Support & Updates
HP Serviceguard Linux Extended Distance Cluster (XDC) for HP ProLiant/x86 Servers
Licensed per physical server
Includes media and One Year 24x7 Software Support & Updates
NOTE: The above is not a complete list of all HP Serviceguard for Linux product
numbers. For a detailed list of supported configuration/certification options for HP
Serviceguard for Linux, please refer to the HP Serviceguard for Linux Configuration &
Ordering Guide available at: http://www.hp.com/go/sglx/info.
NOTE: HP Serviceguard for Linux products running on x86 platforms now include one
year of 24 x 7 Software Technical Support and Updates. Please see the Support
Information section of the HP Serviceguard for Linux QuickSpecs for details.
NOTE: For additional information including a complete list of Product Numbers for
HP Serviceguard for Linux, please see the following QuickSpecs at:
http://h18000.www1.hp.com/products/quickspecs/11518_div/11518_div.html
(Worldwide)
463834-B21
HP USB 2-Button Optical Scroll Mouse (Carbonite/Silver)
HP 1GB USB 2.0 Floppy Drive Key
HP 256MB USB 2.0 Floppy Drive Key
Multibay II 9.5mm DVD Drive
2004 Standard Keyboard USB
1.44MB External USB Floppy Drive
DC172B
442085-B21
442084-B21
PA849A
DT528A#xxx
DC141B
DA - 13166
Worldwide — Version 3 — December 15, 2008
463835-B21
Page 22
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Options
Service and Support
Offerings
(HP Care Pack Services)
NOTE: The HP Care Pack service part numbers below for ProLiant BL c-Class server
blades, cover the server blade and all HP branded hardware options qualified for the
server, purchased at the same time or afterwards, internal to the server.
Hardware Services On-site Service
4-Hour On-site Service, 5-Day x 13-Hour Coverage, 3 Years, Electronic
4-Hour On-site Service, 7-Day x 24-Hour Coverage, 3 Years, Electronic
6-Hour Call to Repair, On-site Service, 7-Day x 24-Hour Coverage, 3 Years,
Electronic
Support Plus 24
Onsite HW support 24x7, 4hr response and Microsoft O/S SW Tech support offsite,
onsite at HP's discretion, 24x7 2hr response time incl. HP holidays, Electronic
DA - 13166
Worldwide — Version 3 — December 15, 2008
UK065E
UK066E
UK067E
UE473E
Page 23
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Memory
NOTE: Memory configurations listed do not apply to "Factory Integrated Models".
DIMM installation guidelines:
1.
2.
3.
4.
5.
All DIMMs must be PC2-5300 Fully Buffered DIMMs at 667 MHz.
Both DIMM slots in a memory bank must be populated.
Banks must be populated in sequential alphabetic order, starting with bank A.
Both DIMMs in a memory bank must be identical. Install identical DIMMs as pairs only, starting with DIMM socket 1, bank A.
Multiple advanced memory protection (AMP) modes are supported, based on FBDIMM population and RBSU selection. The
server blade defaults to Advanced ECC
HP ProLiant BL460c G5 Server Blade (1P Model)
Standard Memory
2048 MB (2 x 1024 MB) of PC2-5300, FBD DDR2-667 ECC DIMMs
Standard Memory Plus Optional Memory
Up to 26624 MB (depending on model) of PC2-5300, FBD DDR2-667 ECC DIMMs. Memory is available with the installation of
optional PC2-5300, FBD DDR2-667 DIMM memory expansion kits.
Standard Memory Replaced with Optional Memory
Up to 32768 MB of PC2-5300, FBD DDR2 FBD-667 ECC DIMMs. Memory is available with removal of standard and the
installation of optional PC2-5300, FBD DDR2-667 DIMM memory expansion kits.
Memory
Slot
1A
2C
3A
4C
5B
6D
7B
8D
Standard
2048 MB 1024 MB
Empty
1024 MB
Empty
Empty
Empty
Empty
Empty
Optional 26624 MB 1024 MB 4096 MB 1024 MB 4096 MB 4096 MB 4096 MB 4096 MB 4096 MB
Maximum 32768 MB
4096 MB 4096 MB 4096 MB 4096 MB 4096 MB 4096 MB 4096 MB 4096 MB
Following are memory options available from HP:
2 GB FBD PC2-5300 (2 x 1 GB LP) Kit
4 GB FBD PC2-5300 (2 x 2 GB LP) Kit
8 GB FBD PC2-5300 (2 x 4 GB LP) Kit
DA - 13166
461826-B21
461828-B21
466440-B21
Worldwide — Version 3 — December 15, 2008
Page 24
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Storage
1-2
2 x SFF SAS or SATA Hot Plug Hard Drives
Hard Drives
SAS Hot Plug SFF Enterprise (ENT) Drives
Position
Quantity
Supported
Supported
Controller
300GB 3G SAS 10K
2
1-2
HP Smart Array E200i Controller
146GB 3G SAS 10K
72GB 3G SAS 15K
72GB 3G SAS 10K
36GB 3G 15K SAS
SATA SFF Hot Plug Entry (ETY) Drives
Position
Quantity
Supported
Supported
Controller
250GB 3G SATA 5.4K
2
1-2
HP Smart Array E200i Controller
120GB 1.5 G SATA 5.4K NOTE: This option is not supported or available within the Drive-less CTO Model.
External Storage
Quantity
Position
Supported
Host Controller or Adapter
Supported
XP Disk Array Systems
Please see the XP
External
Please see the XP Disk Array Systems Quick Specs for the latest list
Disk Array
of supported HBAs
Systems
QuickSpecs
below to
determine
configuration
requirements
HP StorageWorks XP10000 Disk Array:
http://h18006.www1.hp.com/products/storageworks/xp10000/index.html (Worldwide)
Enterprise Virtual Array
Please see the XP
External
Please see the XP Disk Array Systems Quick Specs for the latest list
Systems
Disk Array
of supported HBAs
Systems
QuickSpecs
below to
determine
configuration
requirements
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 25
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Storage
HP StorageWorks Enterprise Virtual Array Family:
http://h18006.www1.hp.com/products/quickspecs/12408_div/12408_div.html (Worldwide)
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 26
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Technical Specifications
System Unit
Dimensions (H x W x D)
(with bezel)
Weight
(approximate)
Power Specifications
7.154 x 2.19 x 20.058 in (18.17 x 5.56 x 50.95 cm)
Maximum
14.20 lb (6.44 kg)
(all hard drives and
processors installed)
Minimum
10.75 lb (4.87 kg)
(one hard drive and
processor installed)
For power specifications including Input Requirements, BTU Rating, and
Power Supply Output, please see the HP BladeSystem c-Class Enclosures
QuickSpecs located at URL:
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/
12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_div/
12810_div.html
To review typical system power ratings use the HP BladeSystem Power Sizer
which is available via the online tool located at URL:
http://www.hp.com/go/bladesystem/powercalculator
System Inlet Temperature Operating
10° to 35°C (50° to 95°F) at sea level with an
altitude derating of 1.0°C per every 305 m
(1.8°F per every 1000 ft) above sea level to a
maximum of 3050 m (10,000 ft), no direct
sustained sunlight. Maximum rate of change is
10°C/hr (18°F/hr). The upper limit may be
limited by the type and number of options
installed.
Relative Humidity
(non-condensing)
Altitude
Acoustic Noise
DA - 13166
System performance may be reduced if operating
with a fan fault or above 30°C (86°F).
Non-operating
-30° to 60°C (-22° to 140°F). Maximum rate of
change is 20°C/hr (36°F/hr).
Operating
10 to 90% relative humidity (Rh), 28°C (82.4°F)
maximum wet bulb temperature, noncondensing.
Non-operating
5 to 95% relative humidity (Rh), 38.7°C
(101.7°F) maximum wet bulb temperature, noncondensing.
Operating
3050 m (10,000 ft). This value may be limited by
the type and number of options installed.
Maximum allowable altitude change rate is 457
m/min (1500 ft/min).
Non-operating
9144 m (30,000 ft). Maximum allowable
altitude change rate is 457 m/min (1500 ft/min).
For acoustic noise specifications, please see the HP BladeSystem c-Class
Enclosures QuickSpecs located at URL:
Worldwide — Version 3 — December 15, 2008
Page 27
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Technical Specifications
HP BladeSystem c3000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12790_div/
12790_div.html
HP BladeSystem c7000 Enclosure QuickSpecs:
http://h18000.www1.hp.com/products/quickspecs/12810_div/
12810_div.html
HP Smart Array E200i
Controller
Disk Drive and Enclosure 3G SAS (Serial Attached SCSI)
Interface
1.5G SATA (Serial Advanced Technology Attachment)
DDR-1/266 MHz provides up to 4.2 GB/s maximum bandwidth.
Cache Memory Speed
x4 2.5G PCIe provides 2GB/s maximum bandwidth.
Server Interface
x2 3G SAS provides 600MB/s maximum bandwidth.
SAS Speed
40-bit 64 MB or 128 MB cache: ECC protection, battery-backed, and
Cache Memory
transportable
Logical Drives Supported Up to 32 logical volumes
Maximum Logical Drive 144GB (2 x 72GB)
Capacity
Host Memory Addressing 64-bit, supporting greater than 4GB server memory space
RAID 5 (Distributed Data Guarding) requires 128MB BBWC option
RAID Support
RAID1, 1+0 (Striping & Mirroring)
RAID 0 (Striping)
Upgradeable Firmware
Upgradeable Firmware
Embedded NC373i
Multifunction Gigabit
Server Adapter
Network Processor
Data Transfer Method
Network Transfer Rate
IEEE Compliance
Standard Features
DA - 13166
Broadcom 5708S
Four lane (x4) PCI Express
2000 Mb/s full duplex (theoretical maximum value)
NOTE: The Gigabit Ethernet adapters above transmit from the server at
2000 Mbps, full duplex per port only. For more information, see the
"Network Controller" segment in the Standards Features section.
802.1p, 802.1Q, 802.3, 802.3ad, and 802.3x
TCP/IP offload engine (TOE) for Microsoft Windows 2003
iSCSI Boot for Linux
Optional accelerated iSCSI
9K jumbo frames
TCP/IP checksum offload (TCO)
Large send offload (LSO)
Interrupt coalescence
Dual address cycles (DAC)
Wake-on-LAN (WOL)
Pre-boot execution environment (PXE)
ProLiant Teaming including Network Fault Tolerance, Transmit Load
Balancing, and Switch-Assisted Load Balancing
IPv6 packet transmit and receive (excluding all offload capabilities);
IPv6 aware SNMPv1 agents for Microsoft Windows
Worldwide — Version 3 — December 15, 2008
Page 28
QuickSpecs
HP ProLiant BL460c Generation 5 (G5) Server Blade
Technical Specifications
Environment-friendly
Products and Approach
End-of-life Management
and Recycling
Hewlett-Packard offers end-of-life HP product return, trade-in, and recycling
programs in many geographic areas. For trade-in information, please go to:
http://www.hp.com/go/green. To recycle your product, please go to:
http://www.hp.com/go/green or contact your nearest HP sales office.
Products returned to HP will be recycled, recovered or disposed of in a
responsible manner.
The EU WEEE directive (2002/95/EC) requires manufacturers to provide
treatment information for each product type for use by treatment facilities.
This information (product disassembly instructions) is posted on the Hewlett
Packard web site at: http://www.hp.com/go/green. These instructions may
be used by recyclers and other WEEE treatment facilities as well as HP OEM
customers who integrate and re-sell HP equipment.
© Copyright 2008 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
Microsoft and Windows NT are US registered trademarks of Microsoft Corporation. Intel, the Intel logo, Xeon and Xeon Inside are
trademarks of Intel Corporation in the U.S. and other countries.
The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and
services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
For hard drives, 1GB = 1 billion bytes. Actual formatted capacity is less.
DA - 13166
Worldwide — Version 3 — December 15, 2008
Page 29