High Resolution Inkjet Printer User Manual

Edition: 20170809A04
V1H
High Resolution Inkjet Printer
User Manual
Revision History
Version
Date
Page
Revised Brief Description
Corresponding
software version
1、Added logo source
30、47、 2、Added plugin management
A02
2017/3/9
1.0.0.1745
49、50
3、Added encoder information
4、Added photocell information
1、Updated default source list and
added Cut Edge feature
18、33、 2 、 Initial setting: added modify
A03
2017/5/22
1.0.0.2086
46、48
string feature
3、Updated ink information
4、Updated battery indicator
1、Add Simple Model
2、Adjust the setting of the jet
printing parameters
A04
2017/7/31
3、Parameters->Option: Add Blank
Line No Print
4、Support importing JPG、PNG、
GIF images.
IMPORTANT
To ensure the best printing quality, we recommend to use our specified cartridges and the
corresponding accessories. Any malfunction or poor printing quality caused by improper use of inks
or accessories which are not from Sojet will not be guaranteed.
Safety Precautions
High voltage inside the machine after electricity connection, Maintenance or disassembly by
unqualified or unprofessional person is strictly prohibited, in order to prevent any accidents.
Machine must be reliably grounded by connecting the grounding wire with the machine when install
equipment, wrong grounding will result in machine failure and the machine don’t work normally.
Do not expose ink directly under sunlight or high temperature (35℃ above). The heat of direct sunlight
or high temperature will affect ink’s storage life and printing quality.
If get ink spill on the eyes or skin, please wash your eyes or skin with clean water.
Ink leakage inside printer will cause burnout damage to machine. Switch off the machine and unplug
it from power outlet when ink leakage inside printer. Contact qualified service technician for test and
repair.
Warning Signs
Caution: The sign “
Attention: The sign “
” indicates possible damage to hardware of inkjet printer or data loss.
” indicates important notes helpful for your trouble-free operation
Please read manual carefully before you use our inkjet printers.
Introduction
Thank you for purchasing our high resolution printer. We want you to get helpful information with this
machine, please read the manual to learn more about our machine by the following content:
Important precautions for use of the machine
Introduction of printer: Parts and components of the machine
Setup and Installation Instructions: Instructions for Equipment Setup and Cartridge Installation.
How to use the printer and the check work before/after use of the printer: explanations of general
operation and startup/shutdown.
Operation instructions: explanations on how to new/edit data for printing, and how to adjust
printer settings.
Care
and
Maintenance:
Care
and
maintenance
for
printer
and
cartridge
Troubleshooting: Common failures and solutions
Appendix 1 - Terms and Definitions: Definitions for terms used in this document.
Please read this user manual carefully before using the printer to get full understanding and
knowledge of importance so that you will get full play of our machine, This will also help you to have
a quick reference to related sections when you have some problems during operation.
Note 1: If you cannot solve the problem encountered during operation, please contact us
Note 2: The information contained herein is subject to change without notice. The user manual will be
updated and revised timely if necessary by publish new version
Note 3: Any machine failure or damage caused by user’s negligence, it is no warranty.
Contents
Important Precautions for User ............................................................................................................ 1
Installation and Setup Instructions ...................................................................................................... 2
1.1 Parts List ......................................................................................................................................................................... 2
1.2 Battery Charging ............................................................................................................................................................ 3
1.3 Battery Installation and Removal ................................................................................................................................... 3
1.4 Ink cartridge Installation (42ml) ..................................................................................................................................... 3
1.5 Position Wheel Mechanism Replacement ..................................................................................................................... 4
1.5.1 Dual wheel mechanism removal and installation: ................................................................................................. 4
1.5.2 Four-wheel mechanism removal and installation .................................................................................................. 5
Inkjet Printer Introduction ................................................................................................................... 6
2.1 Printer ............................................................................................................................................................................ 6
2.2 Technical Specifications ................................................................................................................................................. 7
2.2.1 Performance Values ............................................................................................................................................... 7
2.2.2 Features ................................................................................................................................................................. 8
2.2.3 Ink Solutions ........................................................................................................................................................... 8
Printer Operation Instructions ............................................................................................................. 9
3.1 Power On ....................................................................................................................................................................... 9
3.2 Main Interface ................................................................................................................................................................ 9
3.3 How to Upgrade Software.............................................................................................................................................. 9
3.4 How to Import / Export Data, Images, and Set Parameters ....................................................................................... 100
3.4.1 Recover data / Image / Print parameters / System parameters ........................................................................ 100
3.4.2 Backup Data / Images / Print Parameters / System Parameters ....................................................................... 111
Function Introduction ........................................................................................................................ 122
4.1 Message Management---standard model.................................................................................................................. 122
4.1.1 List Function ....................................................................................................................................................... 122
4.1.1.1 Message List ............................................................................................................................................ 122
4.1.1.2 Object List...................................................................................................................................................... 13
4.1.2 Tool bar ................................................................................................................................................................ 14
4.1.3 New Text Message ............................................................................................................................................... 15
4.1.4 Add Date/Time ..................................................................................................................................................... 18
4.1.5 Add Counter ....................................................................................................................................................... 200
4.1.6 Add Shift Object ................................................................................................................................................. 222
4.1.7 Add Local Image Object ....................................................................................................................................... 23
4.1.8 Add Base Image ................................................................................................................................................... 25
4.1.9 Add Device Name Object...................................................................................................................................... 25
4.1.10 Add Scan Print Object......................................................................................................................................... 25
4.1.11 Add Barcode ....................................................................................................................................................... 26
4.1.12 Edit Message ...................................................................................................................................................... 28
4.1.13 Copy/Paste Message .......................................................................................................................................... 28
4.1.14 Delete Message .................................................................................................................................................. 28
4.2 Message Management---Simple Mode ....................................................................................................................... 28
List Function .................................................................................................................................................................. 28
4.2.1 Message List ..................................................................................................................................................... 28
4.2.2 Object List ........................................................................................................................................................ 30
4.2.3 Toolbar ............................................................................................................................................................. 31
4.2.4 New Message ................................................................................................................................................... 32
4.2.4.1 Text object................................................................................................................................................. 32
4.2.4.2 Counter object ........................................................................................................................................... 33
4.2.4 .3 Date/Time object ..................................................................................................................................... 35
4.2.4 .4 Shift object ............................................................................................................................................... 38
4.2.4 .5 Scan print object ...................................................................................................................................... 41
4.2.4 .6 Barcode object ......................................................................................................................................... 42
4.2.4 .7 Logo object ............................................................................................................................................... 44
4.2.5 Edit Message ........................................................................................................................................................ 45
4.2.6 Copy/Paste/delete Message ................................................................................................................................ 45
4.2.7 Delete Message .................................................................................................................................................... 45
4.3 Printing Management .................................................................................................................................................. 45
4.3.1 Start/Stop Printing ............................................................................................................................................... 45
4.3.2 Printing Report Display ........................................................................................................................................ 46
4.3.3 Printing Delay ....................................................................................................................................................... 46
4.3.4 Initial Setting ........................................................................................................................................................ 47
4.3.5 Printing Monitor................................................................................................................................................... 47
4.3.6 Re-print ................................................................................................................................................................ 48
4.4 Printing Parameter ....................................................................................................................................................... 49
4.4.1 Print Setting ......................................................................................................................................................... 49
4.4.2 Printhead Setting ................................................................................................................................................. 49
4.4.3Printing Option ...................................................................................................................................................... 49
4.4.4 Special Printing .................................................................................................................................................... 50
4.5 System setting ............................................................................................................................................................ 500
4.5.1 System management ......................................................................................................................................... 500
4.5.2 User management ............................................................................................................................................. 511
4.5.3 System reset ......................................................................................................................................................... 53
4.5.4 About.................................................................................................................................................................... 55
4.6 Tools ............................................................................................................................................................................. 55
4.6.1 How to manage local images ............................................................................................................................... 55
4.6.2 How to upgrade language/font/typewriting ....................................................................................................... 56
4.6.3 Permission ............................................................................................................................................................ 57
4.6.4 Plugin Management............................................................................................................................................. 58
4.7 Status bar ..................................................................................................................................................................... 58
4.7.1 Cartridge status ................................................................................................................................................... 58
4.7.2 System status ....................................................................................................................................................... 59
4.7.3 Encoder information ............................................................................................................................................ 59
4.7.4 Photocell information........................................................................................................................................... 60
4.7.5 USB Status .......................................................................................................................................................... 600
4.7.6 Battery Indicator ................................................................................................................................................ 600
4.7.7 WI-FI Status ........................................................................................................................................................ 611
4.7.8 Log out ............................................................................................................................................................... 611
4.8 Input Method Introduction ........................................................................................................................................ 611
Appendix 1: Terms and Definition ..................................................................................................... .65
Important Precautions for User
Welcome to use this inkjet printer. In order to protect your personal safety and user rights, ensure correct
installation and operation, and full play of the machine, it is important that you read the precautions carefully.
Important Installation Precautions
 The recommended spacing distance should be 0.5-2.5mm between internal deflector of printer and
printing object.
 Make sure to insert or remove ink cartridge by an angle of 15 degree so as not to damage the cartridge.
 Do not place the printer in a dusty environment and longtime use, if customer can’t change, please clean
the printer dust periodically .
 Printer only can use original battery and charger provided by manufacturer. Do not open or place in a fire,
and not allow metal contact or electrode short circuit, avoid placing in excessive heat (over 60 degrees
Celsius), humid or corrosive environments.
Important Operation Precautions
 Do not poke or impact the touch screen sharply.
 The built-in photocell can’t be covered, or the printer doesn’t print.
 Use Non-woven to wipe the nozzle plate when the print is not clear or dots are missing.
 When printing position is changed, please set the printing delay to achieve best printing result.
 Do not insert or remove ink cartridge while the machine is in printing process so as not to cause damage
to the cartridge.
 Do not use compressed air for cleaning the touch screen. High pressure of the compressed air will
damage the touch screen.
 Do not use compressed air for direct or indirect cleaning of the ink cartridge. High pressure of the
compressed air will damage the nozzle plate.
Note: It is necessary for some cartridges to be removed from machine after operation stop. Turn off the
machine and remove the cartridge from printer. Wipe the print head clean with Non- woven cloth; lock the
print head with the special cap to avoid the nozzles blocking (Contact our after-sale service for more about
cartridges)
1
Installation and Setup Instructions
This chapter illustrates product parts list and installation of equipment and ink cartridge.
Packing Pictures
Outer box
1.1 Parts List
Please check everything with packing list to make sure all required parts in the package when you receive
the products.
SN
Part Name
QTY
Photo
Handheld printer
1
1
2
USB disk
3
Battery
4
Charger
1
1
1
5
Wrist Strap
1
2
Note
1.2 Battery Charging
Battery charging:
Battery charging finished:
Insert battery into
Remove battery from charger.
charger.
Green indicator light:
Battery not inserted or
Red indicator light:
battery fully charged.
Battery is on charge.
1.3 Battery Installation and Removal
Battery installation:
insert the battery into
Battery removal:
handle and hear
Press the two lock
“click” indicates the
catches on battery,
battery is well fixed.
remove battery from
printer.
1.4 Ink cartridge Installation (42ml)
Cartridge removal:
Insert cartridge to
Remove cartridge from
printer by an angle of 15
printer by an angle of
degree. Press vertical
15 degree.
when insert right
position, then hear
"click”, that means the
cartridge already is
fixed well.
3
1.5 Position Wheel Mechanism Replacement
1.5.1 Dual wheel mechanism removal and installation:
Installation:
As shown vertically
inward install the dual
wheel mechanism, and
lock the screws.
Removal: Take off fixed
screws, vertically outward
pull the dual wheel
mechanism.
Well-installed dual wheel mechanism:
4
1.5.2 Four-wheel mechanism removal and installation
Installation:
As shown vertically inward
install the four-wheel
mechanism, and lock the
screws.
Removal: Take off fixed
screws, vertically outward pull
the four-wheel mechanism.
Well -installed four-wheel mechanism:
5
Inkjet Printer Introduction
2.1 Printer
5”touch screen
Four-wheel
mechanism
Switch
Handle
Battery lock
catch
Battery
Reinstallation
button
USB port
Indicator light
Power switch
Wristband
fixed point
6
2.2 Technical Specifications
2.2.1 Performance Values
Items
Technical source
Specifications
Note
HP TIJ2.5 Thermal Ink Jet technology;
(H*W*D): 218*52*152mm;
Dimension
(H*W*D): 218*79*152mm (four-wheel mechanism
included )
Weight
0.74kg
Power input
AC90V-240V, 50-60HZ
Specified
Battery
charger
Quantity
Two standard large capacity rechargeable
batteries.
Capacity
Darongliang
3 section 2200mAh battery module
Charging time
approximately 1.5H
Voltage
for full. The light is
11.1-12.6V
red when in charging
Battery
Lifetime
Approximately 300 cycles.
the indicator light is
yellow once power is
Print height
Print speed and
Standby time
Approximately 7H.
Working time
Approximately 4H.
1-12.7mm
Standard 300DPI
resolution
Print content
Barcode, alphabetic, numeric, Chinese, image, date, shift
group, counter, scanner
Ports
USB2.0 port
Interface
5inch Capacitive touch screen with 1280*720 resolution
7
full
Automatically identify ink types and optimum printing
parameters
Ink management
Guarantee genuine original HP ink;
Automatically measure the status of ink usage
Product Certification
CE, FCC
Environment
Working environment: -10℃--55℃; 10%-85%RH
requirement
Storage environment: -25℃--80℃; 10%-90%RH
2.2.2 Features
Items
Languages
Font
Barcode
Specification
Chinese, English, French, German, Spanish, Portuguese,
Russian, Korean and Japanese
Default font is Arial bold ; allow users to load whatever fonts
they need
Code128, Code39, EAN8, EAN13, EAN128, UPCA, UPCE,
INT25, PDF417, DATAMATRIX, QR、ITF14、Code93
Date format
Variety of date formats available
Multi-management
Customized different users and rights
2.2.3 Ink Solutions
 Support 42ml cartridge of HP TIJ2.5 technology;
 Support ink of various colors: black, red, green, yellow and blue;
 Support porous, semi-porous and non-porous substrates.
8
Note
Printer Operation Instructions
3.1 Power on
Make sure the power is on before use printer, press the power switch, then enter the main interface.
If the printer screen is not light after turn on, it may be low battery, please charge it with specified
charger.
3.2 Main Interface
 Printing: List, start/stop print, print delay, print initial value, printing monitor, re-print.
 Parameters: Print setting, printhead setting, print options, special print.
 Message: List, new message, edit message, delete message, copy/paste message.
 Setting: Setting management, user management, system reset ,about.
 Tools: Image management, upgrade management, backup recovery, authority registration and plugin
management.
 Status bar: Status of ink, equipment, encoder, photocell, USB, WI-FI, power and log off.
3.3 How to Upgrade Software
If you want to upgrade software, please do as below steps:
 First copy the installation package to the U disk path【Inkjet/Upgrade/Application/ 】.
 Insert the U disk into USB port of device, when the USB icon display green in the status bar,
dedicates that U disk has been identified by the device.
9
 Click【Tools】>【Upgrade】>【Software】, click the button
【Upgrade】 to enter the list of upgrade
package.
 Find your required upgrade installation package in the list, click the
in the upper right corner,
then you can upgrade.
 After upgrade successfully, the device will restart automatically, you can check whether the software
version is what you need by 【Setting】>【About】
Tips:
 Different printer only can be upgraded with corresponding install package, please take care in case of
wrong upgrade.
 If installation package is not in the right specified path, click the button
to enter the other
folders, select the right upgrade package to upgrade. Please refer to how to upgrade language, fonts and
input method.
3.4 How to Import / Export Data, Images, and Set Parameters
3.4.1 Data recovery/ Image / Print parameters / System parameters
 Save the backup file under the U disk path (Inkjet/backup/), insert U disk, and click【Tools】>
【Backup】
 Select required recovery backup file from drop down list.
 Check recovery method, you can only choose one corresponding method, If you don’t choose, it
won’t recover corresponding type.
Clear
Message
Clear all original
data, only keep
restoration data.
Replace
If restored data is with
the same file name as
original data, then
restored data replace
the original data and
the file name
unchanged
10
Addition
If restored data is with the same
file name as original data, only
add non-duplicate files, the
data with same file name
excluded
Delete all original
images, only keep
restored images
Image
If restored image is
with the same file
name as original then
restored image replace
the original and the
file name unchanged
Parameter
Restored parameters
replace original
parameters
Setting
Restored parameters
replace original
parameters
 Click
If restored image is with the
same file name as original,
only add non-duplicate files,
the image with same file name
excluded
【Recovery】to perform recovery operation. After recovery successfully, the device will
reboot automatically, then the content of device will correspond with original file.
Tips:
 Save recovery file under the path: Inkjet/Backup/
 It is impossible to recover for File name exceeds 30 characters or contain symbols “\/:*?"<>|”
 Data import via function of【Message】, please refer Data Management for details.
 Images import via【Tools】>【Image】, please refer How to manage local images for details.
3.4.2 Backup Data / Images / Print Parameters / System Parameters
 Insert U disk, click【Tools】>【Backup】
 Click required backup option, multi-optional available (backup will be failure if not select any
options,)
 Backup name is available for 30 characters limit, English, numbers, symbols ( Except“\/:*?"<>|”)
and Chinese, the backup name cannot be empty.
 Click
【Backup】 and backup finish, save path under :
Inkjet/Backup/
Tips:
 Backup files through export function of data list, please refer to Data Management for details
 Backup images through image management, please refer to How to manage local images for details
11
Function Use Introduction
4.1 Message Management-Standard Mode
4.1.1 List Function
4.1.1.1 Message List
Click【Message】>【List】, unfold the message list; Click【List】again to hide the list.
 List mode switch: Display message in the default way of list, click
display mode; Click
【List】, and switch to icon
【Icon】, can switch back to list display mode; Select message, click
【Edit】,
and enter message edit interface.
 Expand list width: If the message name is long, and the list display incomplete, click
button, the list width will be expanded, then can display complete message name; Click
【Unfold】
【Recovery】
again, then return back to normal width.
 Search message: Click
【Search】, then popup search input box, enter keywords to match
searching, then list will show exact message; After clear input box, list will display all messages.
Message management: Click
【Manage】, popup message management options; Click
again, and hide message management options.
12
【Manage】
Import message: Insert U disk, after device identify U disk, click 【Import】, and then
message of U disk: Inkjet/msg will be imported into list automatically; When the import message name
same with device, it will popup reminder, and choose whether to continue import according to reminder.
needed imported message, click【Export】, then the
Export message: Insert U disk, check
selected message will be exported to U disk patch: Inkjet/msg
Rename: Select file, then click 【Rename】, popup keyboard to edit message name, and take
effect after save.
Select all: Click【All】, select all messages in the list automatically, switch button to 【None】;
【None】, selected messages will be canceled, then button switch back to【All】.
Click
Tips: Device maximum can save 500 messages, it can’t continue add or import data after the
message reach maximum.
4.1.1.2
Object List
【Message】>【List】,select message, click【Edit Message 】 or 【New Message 】, then messages
list change to object list, display all objects of this message.
 Switch Source List: Click
【Switch】,switch to source list, click【Switch】again, then can switch
to object list.
 Object Arrangement: Click
【Arrange】, popup object alignment way, move up and down
options.
Sort Keypad Description:
SN.
Icon
Description
SN.
13
Icon
Description
1
Align selected objects to the
5
Align selected objects at the
left
2
top
Align
selected
objects
to
6
Align selected objects up and
centered right and left
3
down
Align selected objects to the
7
Align selected objects at the
right
4
Align
bottom
selected
objects
at
8
Align selected objects at
vertical distribution
 Object Management: Click
Copy
transverse distribution
【Manage】, selectable object editing shortcuts.
objects
to
the
Rename objects
clipboard
Copy /paste or cut objects
Delete Objects
Select all Objects
Select none
 Expanded List Width: If the object name is long, the list will show incompletely, if only click
【Unfold】, the list will be expanded, and display completely; Click
【Recover】again, then can recover
to normal.
 Switch List Display Way: Display object in the way of default list, click
【List】, switch to icon
【Icon】again, can switch back to list display way; Select object, clip
display way; Click
【Edit
object】,then can enter object editing interface.
Source List
Enter Switch source list of object list according to above steps. Details refer to Object list
4.1.2 Toolbar
There are only three kinds buttons【Zoom Out】【Zoom in】【Self-adaptive】in the toolbar of message
management preview and object edit; Except these three kinds button in the toolbar of new and edit message
interface, there are【Cancel】【Recover】【Copy】【Paste】【Delete】buttons.
Click
【Tools】, expand various shortcuts.
Cancel
Copy
Delete
Paste
Recovery
Zoom Out
Zoom in
14
Self-adaptive
【Undo】: Click once, can undo operation of step forward for one time, maximum can undo 5 steps
operation.
【Recover】: After perform one undo command, click Restore key can restore content of
revocation.
【Copy】: Click object/source in the preview interface, click 【Copy】 to clipboard.
【Paste】: Paste copy or cut object/source to the preview interface.
【Delete】: Click object/source in the preview interface, Click 【Delete】, then will delete from the
interface.
【Zoom in】: Enlarge 20% canvas size for every time clip.
【Zoom out】: Zoom out 20% canvas size for every time clip.
【Adaptive screen】: Display canvas size in 1:1 ratio.
 Click
 Click
【Tools】again, the toolbar will be hidden
every time, the preview interface will add one line canvas, multi-line data can be built to
maximum 16 lines.
 Click
every time, the preview interface will reduce one line canvas.
4.1.3 New Text Message
New Text Source
【Message】>【New】>【New source】>【Text】
 Enter text content: Maximum can input 100 characters, you can input Chinese, English, numbers,
symbols and third-party language.
 Source name: Maximum 30 characters, you can input Chinese, English, numbers, symbols, and
third-party language; Empty name and rename with added source are not allowed.
 After setting content name, click
【Return】, save text source, return to new data interface.
New Text Objects
【New object】>【Text】
 The default display text content (EXAMPLE TEXT)
15
Added
source list
Built
source list
Built Source List: Display the newly built source of this data, 【Default-Text】【Default-Counter】
【Default-Shift】
【Default-Date time】 are fixed “source” which can be added directly; The list shows up to 50 sources which can
drop-down slider to view.
【New】, popup source type, and enter new create interface after selection, it will display
New Source: Click
in【Built Source List】after saving, and can use directly.
Edit Source: Select the source which you want to modify in the【Built Source List】, click
【Edit source】,
popup corresponding source setting interface.
Add the “Source” to the object: Select the “source” which want to add in the built source list, click side
【Add】,then will add automatically to the preview interface and added list.
Note: Maximum can add 50 “sources”.
Added Source List: Display current source of object which has been added in order.
Adjust the sources order of object: Select “source” of list, click
【Prev.】
【Next】to adjust order.
Delete “source” of object: Select source which need to be deleted in the added source list first, then click side
button
【Delete】, a key to delete.
 Click
【Shortcut】, switch to quick input interface. You can input Chinese, English, numbers,
symbols, and third-party language, 100 characters limited. (Note: If you have already added the source
in 【Routine】 interface, then the input is invalid.)
 Character
Font: Select the font.
Size: Set the font size.
Font effect:
Bold,
Italic,
Add under horizontal line,
16
Add font with horizontal
line
Cut Edge: Set whether the objet with white lace.
 Paragraph
Spacing: Distance between words, you can enter 0-100, one decimal place
Leading: The distance between two lines. Input range is limited depending on the canvas
Text Alignment Way:
Align multiple lines to the left
Align Multiple lines centering
Align multiple lines to the right
Align multiple lines left and
right justification
 Location
X axis coordinates: Input range -10-3000mm, you can click
buttons to adjust slightly.
Y axis coordinates: Input range according to canvas amount limited, also can click
buttons to
adjust slightly.
Width: You can enter 10% to 300%, the greater value, the larger width font.
Height: You can enter 10% to 300%, the greater value, the higher font.
Lock scale: The proportion of font height and width. After select this function, when modify the font width or
height, the font will be proportionally adjusted.
Tips: If the data location beyond the canvas, it will turn yellow,
after saving only the content within the canvas can be printed.
 Rotation
Rotation: Input range 0-359, also can click
buttons to adjust.
Mirror: There are None, Horizontal mirror, Vertical mirror three options, click the drop-down button to
expand
Gradation: Printing darkness can be set within 10-100%.
17
 Name
It can be set to Chinese, English, numbers and symbols; cannot exceed 30 characters, empty and rename with added
object are not allowed.
 Finally click
Return to save the text object, return to new data interface of previous level.
Save Data
 After create text object, return to new interface, click
again, then enter to data name setting
interface, you can input Chinese, English, numbers, symbols, third-party language, data name no more than
30 characters; Empty and rename with added data are not allowed.
 After entering data name, click
in the upper right corner, the system will prompt data save
successfully, then return to main interface! Click
, won’t save, and then return to data interface.
Error data content (data red), the system will prompt an error, you can save after normal
modify.
4.1.4 Add Date/Time
Create Date/Time source (production date, expiry date)
【Message】>【New】>【New source】>【Date Time】
 Select format: select format from the menu, system has 5 default formats, user can define totally 45
types. The default ones cannot be deleted or modified, default formats include: YYYYMMDD,
YYYY/MM/DD, MM/DD/YYYY, HH:mm, Julian day.
Add new format: if user wants to add a new format or modify an exist one, click
management list.
18
, popup date format
Format List: Display the default formats and newly added formats.
New: Click the new pop-up the date format setting keyboard, can choose a custom date format.
Format name enter no more than 30 characters, and cannot be input (" \ / : *? "< > |"), and can't be
empty, otherwise cannot be saved.
Icons description:
Description
SN
1
4-digit Year
10
2
Last 3-digital Year
11
Minute
3
Last 2-digital Year
12
Second
4
Last 1-digital Year
13
the day of the week
5
Month 01-12
14
6
abbreviated month
15
AM/PM
7
Month name
16
Week of Year
8
Day
17
Name of weekday
18
Day of the year
SN
Icon
9
Hour in 24-hour
time system
Icon
Description
Hour in 12 hour
system
Abbreviation of the
weekday
Edit: Choose date from the format list, and click "edit" popup the Settings interface, can modify and then save. The
default format cannot be modified!
Select all: All formats in the list was chosen; Click the switch again change to all don't choose, all not to choose.
Delete: Select the data format can be deleted. The default format cannot be deleted
Closing date format management: Click on close, out of date format management interface and save existing format.
19
 Expiry date: If only want to add a production date, user may need to set the expiry day to 0; expiry
time can switch from day, week, month, year, value within 0-999.
 Calendar type: Gregorian/ Hirji
 Pre-zero: 4 choices: 2015/01/01, 2015/_1/_1, 2015/1_/1_, 2015/1/1
 Source name: maximum 30 characters, Chinese and English characters, numbers, symbols, name
cannot be blank or overlapped, or cannot be saved.
 Zero Setting:
 【New source】>【Date Time】>【Other】
 First enable the Zero Setting.
 Input the time (hour: 0-23; minute: 0-59)
 Then click the switch button again to get off this setting.
 Day Light Saving:
【New source】>【Date Time】>【Other】
 User can select from OFF, Europe or America.
 Click
to save and return.
Create Text object and add date time source.
How to create a Text object and add date time source into it, please refer to Create Text Object
Save Message
Please refer to Save Message
4.1.5 Add Counter
Add counter source
 【Message】>【New】>【New Source】>【Counter】
 Click
【Edit】
Initial Value: begin value of the counter, range from -999999999999~+999999999999
Maximum Value: Maximum value, range from -999999999999~+999999999999
Repeat Value: range 0~9999
Step Value: for example: step value set to 3, counter will be 1, 4, 7, 11…
Carry System: User can select different carry systems, if need to add a new one, click
20
【Edit】
 System List: Show the default and new built system. It can display a maximum of 5 (including the default base)
 New: Click “new” popup the system editing interface. Enter into the system name and content, click save to save the
system to the list.
 Edit: Selected the system, click “edit” popup the editing interface, click “save” to save the changes. The default system
cannot be edited.
 Select All: All system in the list was chosen; Click the switch again change to all don't choose, all not to choose.
 Delete: Select the newly systems can be deleted. The default system cannot be deleted
 Closing system management: Click on close, out of management interface and save existing system.
Counter Source name: maximum 30 characters, Chinese and English characters, numbers, symbols, name cannot
be blank or overlapped.
 Click
【Other】
Carry Source: Click the pull-down menu to check the added counter.
Set the counter which the carry is based on (e.g there are counter 1 and counter 2, set the carry source of counter 2
to be counter 1, then only after counter 1 reached to the maximum value, counter 2 will carry over.)
Current Value: Set the current value of the counter, value should be within the begin value and maximum value.
Repeat Index Value: Set the current repeat index value, only settable while repeat value is not 0, repeat index
value range is 0-repeat value.
Pre-zero: Pre-zero setting of counter, four options: 0001, ___1, 1___, 1.
Alarm: Whether to give an alarm while counter reach the maximum value. User can switch this option on or off.
Add Counter Source into Text
Please refer to Create Text Object
Save Message
Please refer to Save Message
21
4.1.6 Add Shift Object
Add Shift Source
 【Message】>【New】>【New Source】>【Shift】
 From the pull-down menu, user can check the already existed shifts, if need to create a new one or
modify any of them, click
【Edit】
Shift List: Show the default and new built shift.
New: Building new shift
Shift
content list
 【Interval】: According to the selected time interval, 24 hours a day is divided into the corresponding number of
shifts. For example, the time interval is set to 4H, the system automatically generates 6 shifts (default A-F), and shows
in the left list.
 【Start Time】: Time of first shift. For example, set the interval to 4H, the starting time is set to 8:00, then the
first shift A start time is 8:00, shift B start time is 12:00, shift C start time is 16:00, and so on.
 【Set】: Select the time interval and the start time, click the button【Set】, will generate the default shifts
automatically, and shows in the left list.
22
 【Add】:If need to add another shift, you can input the 【Shift name】 and the 【Time】, click
【Add】,
the new shift will be added to the list on the left side.
 【Shift content list】: Show the current team all content; Maximum user can add 48 shifts.
 【Delete】: If need to delete any shift, select that one in the list, click
 【Delete all】:If need to delete all exist shifts, click
【Delete】
【Delete All】
【Modify Shift Content】: select the shift from the list on the left, then edit its content on the right side,【Add】
will change to【Modify】,click【Modify】to save
 【Shift name】: Maximum 30 characters, can be Chinese, English letters, numbers or symbols (no special
symbols).
 【Save shift】: Click
to save.
Edit: Selected the shift from the 【shift list】, click “edit” popup the editing interface, click “save” to
save the changes. The default shift cannot be edited.
Select All: All shifts in the list was chosen; Click the switch again change to all don't choose, all not
to choose.
Delete: Select the newly shifts can be deleted. The default shift cannot be deleted
Closing Shift Management: Click on close, out of management interface and save existing shifts.
 Shift Source Name
Maximum 30 characters, Chinese or English characters, numbers, symbols, name cannot be blank or
overlapped, or will not be saved.
 Click
【Return】to save the source and go back to previous menu.
Add Shift Source into Text
Please refer to Create Text Object
Save Message
Please refer to Save Message
4.1.7 Add Local Image Object
Add Local Image
 【Message】>【New】>【New Source】>【Local Image】
23
 Select the image from the list.
 Set the name of the local image source: Maximum 30 characters, Chinese or English characters,
numbers, symbols, name cannot be blank or overlapped.
 At last, click
【Return】to save.
Add Local Image in New Logo Object
 【New】>【New Object】>【Logo】
 Click
, select the logo type, types including Local image or Base image.
 Click
【Local Image】, the images in the selected type will be displayed in the list.
 Select the image from the list and set the name of the local image source, click
 Select a source in the image source list, click
 Click
【Return】to save.
to edit.
to set the logo’s specifications.
Width ratio: range from 10-300, the width of the picture will be adjusted automatically.
Height ratio: range from 10-300, the height of the picture will be adjusted automatically.
Lock Percentage: After selected, the height and width of the picture will be adjusted with the same proportion.
 Click
, user can do the position setting on X/Y axis.
X axis: Range -10-3000mm, adjust by
Y axis: Range depends on the canvas size, also can be adjusted by
 Click
.
to rotate the image.
Rotate: rotation angel from 0-359, user may click
to adjust as well.
Mirror: three options: none, Horizontal, Vertical.
Gradation: Printing darkness can be set within 10-100%.
 Click
to name the logo: Maximum 30 characters, Chinese or English characters, numbers,
symbols, name cannot be blank or overlapped.
 Click
to save and return to upper menu.
Save Message
Please refer to Save Message
24
4.1.8 Add Base Image
【Message】>【New】>【New Source】>【Base Image】
【Type】: Four base images: Straight line, Rectangle, Circle and Ellipse. Select one of the base images,
will be displayed in real-time in the left preview box.
【Edit】: According to the selected base image, display the corresponding settings.
Straight line: Length: 1-3000mm. Line Width: 0.1-2mm.
Rectangle: Width: 1-3000mm. Height: 1-12.7mm
Circle: Diameter: 1-12.7mm
Ellipse: Long axis: the lateral diameter of the ellipse, 1-3000mm. Short axis: the vertical diameter of
the ellipse, 1-12.7mm
【Other】: Settings of Rectangle or Circle or Ellipse
Chamfering: The range is 0-999, enter 0 is right angle, enter 999 is semicircle (Settings of Rectangle)
Fill/Stroke: Click the button to switch the Stroke and Fill. Set to Stroke, only show graphic borders.
Set to Fill, shows black graphic, line width setting is not available.
Line Width: the range is 0.1-2mm
【Name】Maximum 30 characters, Chinese or English characters, numbers, symbols, name cannot be
blank or overlapped.
 Click
【Return】to save.
Add base image into logo object and save message please refer to Create Local image object.
4.1.9 Add Device Name Object
Create Device Name Source
【Message】>【New】>【New Source】>【Device Name】
 Generated the device name source directly, the default device information is INKJET. In the【System
Management】 >【Set up Management】modify equipment information, after save the source content updates
automatically.
 In each message can build only one device source.
Add Device Name Source into Text Object
Please refer to Create Text Object
Save Message
Please refer to Save Message
4.1.10 Add Scan Print Object
Create Scan Print Source
25
【Message】>【New】>【New Source】>【Scan print】
 【Edit】:
Preview: The contents of the MSG preview, cannot be print out. Can enter any characters except the
newline.
【Other】:
【Auto Sleep】: Make the device into the low power state. Default value is 1s, the range is 1-60s.
【Read Time】: Default value is 3s, the range is 0-3600s.
【Error Info】: Need to turn on the right switch before use. Only support for input in English.
Name: Maximum 30 characters.
 Click
【Return】to save scan source.
Add Scan Print Source into New Text Object
Please refer to Create Text Object
Save Message
Please refer to Save Message
Print Scan Message
Click start to print, shake the printer the scan light will on, after scan the barcode, light will be off, push
the red button, the message will be printed. If not recognize the barcode, printer will scan for several times,
if no sense for 10s, scan light will be off as well.
Note: One message can only contain one piece scan print source, user can set the scan cache numbers,
the scan message can only print once.
4.1.11 Add Barcode
Create Barcode Object
【Message】>【New】>【New object】>【Barcode】
26

【Shortcut】: Can add Text/Counter/Shift/Data Time/Dynamic Text/ Database Text/Device
Info/line break into barcode object. (Tip: Add scan source and scan the illegal value, the scan source will
change to 00000 in the bar code)
Note: Refer to above create text object about add “source”.
 Click
【type】to select the required barcode type.
 Click【Genre】, user can select 1Dbarcode, 2D barcode.
 User will see the barcode types required.
 Barcode Settings
Note: 1D and 2D barcodes have different settings, user need to select barcode genre firstly.
Barcode type
1D Barcode
Settings
Width: Totally 1-16 levels to choose from.
Height: Within the canvas size,1-12.7mm
Font: Select barcode text font
Font Size: Select barcode text font size.
Text Display: User can switch from on or off.
Cut Edge: Select barcode whether with white lace
Blank Level: 0-4 grades to switch.
2D Barcode
Width: Totally 1-16 levels to choose from.
Error Correction Level: QR code, 1-4 grades;
PDF417, 1-7 grades.
Blank Level: 0-4 grades to switch.
Size:
QR,
DATAMATRIX
specifications.
 Location, Rotation, Name please refer to Create Text Object
Save Message
Please refer to Save Message
27
bar
code
size
4.1.12 Edit Message
 Click【Message】from the main interface, then click【List】to see all the messages added.
 Select the message, and click【Edit】
【New Object】: Please refer to Add New Message
【Edit Object】: select the object need to edit in the list, click【Edit object】
【New Source】: Please refer to Add New Message
【Edit Source】: Select source in【Source list】, click【Edit Source】.
 After editing, click return, choose save or not.
Tips:When the MSG with dynamic source (Counter, Device Info, Date Time, Scan, Shift) has
print records, edit this MSG and save it, will prompt to 【Save】【Not Save】【Save As】【Cancel】options.
Select 【Save As】to retain the original MSG, and create a new MSG. Select 【Save】, the original MSG will
be covered, the print records is cleared and cannot be reprinted.
4.1.13 Copy/Paste Message
Select the message in list, click
【Copy】, and then click any position in the list, click
【Paste】,
the message will be copied and named as the original one with “C1” at the end. For example, if original
message is MSG001, the copied one will be named as “MSG001C1”.
 Can do multiple choice, copy and paste them at the same time.
 If copied several times, only the last copied message(s) will be pasted.
4.1.14 Delete Message
Select the message(s) in the list, click 【Delete】, yes to delete or no to cancel.
4.2 Message Management-Simple Mode
List Function
4.2.1 Message List
Click【Message】>【List】, unfold the message list; Click【List】again to hide the list.
28
 List mode switching: Display message in the default way of list, click
display mode; Click
【List】, and switch to icon
【Icon】, can switch back to list display mode; Select message, click
【Edit】,
and enter message editing interface.
 Expand list width: If the message name is long, and the list display incompletely, click
button, the list width will be expanded, then can display completely message name; Click
【Unfold】
【Recovery】
again, then return back to normal width.
 Search message: Click
【Search】, then popup search input box, enter keywords to match
searching, then list will show exactly message; After clear input box, list will display all messages.
 Message management: Click
【Manage】, popup message management options; Click
【Manage】again, and hide message management options.
Import message: Insert U disk, after device identify U disk, click 【Import】, and then
message of U disk: Inkjet/msg will be imported into list automatically; When the import message name
same with device, it will popup reminder, and choose whether to continue import according to reminder.
needed imported message, click【Export】, then the
Export message: Insert U disk, check
selected message will be exported to U disk patch: Inkjet/msg
Rename: Select file, then click 【Rename】, popup keyboard to edit message name, and take
29
effect after save.
Select all: Click【All】, select all messages in the list automatically, switch button to 【None】;
【None】, selected messages will be canceled, then button switch back to【All】.
Click
Tips: Device maximum can save 500 messages, it can’t continue add or import data after the
message reach maximum.
4.2.2 Object List
【Message】>【List】,select message, click【Edit Message 】 or 【New Message 】, then messages
list change to object list, display all objects of this message.
 Object Arrangement: Click
【Arrange】, popup object alignment way, move up and down
options.
Sort Keypad Description:
SN.
1
Icon
Description
SN.
Align selected objects to the
5
left
2
Arrange
selected
objects
6
Align selected objects to the
Arrange
selected
objects
Arrange
selected
objects
7
Arrange
selected
objects
align bottom
selected
objects
vertical distribution
 Object Management: Click
Arrange
align center up and down
right
4
Description
align to top
centered around aligned
3
Icon
8
Arrange selected objects
transverse distribution
【Manage】, selectable object editing shortcuts.
30
Copy
objects
to
the
Rename objects
clipboard
Copy-paste or cut objects
Delete Objects
Select all Objects
Select none
 Expanded List Width: If the object name is long, the list will show incompletely, if only click
【Unfold】, the list will be expanded, and display completely; Click
【Recover】again, then can recover
to normal.
 Switch List Display Way: Display object in the way of default list, click
【List】, switch to icon
【Icon】again, can switch back to list display way; Select object, clip
display way; Click
【Edit
object】,then can enter object editing interface.
4.2.3 Toolbar
In the process of create and edit message, we can use shortcut function of toolbar to edit object and
source.
Click
【Tools】, expand various shortcuts.
cancel
Copy
Recovery
Delete
Paste
Zoom Out
Zoom in
Self-adaptive
【Undo】: Click once, can undo operation of step forward for one time, maximum can undo 5 steps
operation.
【Recover】: After perform one cancel command, click Restore key can restore content of
revocation.
【Copy】: Click object/source in the preview interface, click 【Copy】 to clipboard.
【Paste】: Paste copy or cut object/source to the preview interface.
【Delete】: Click object/source in the preview interface, Click 【Delete】, then will delete from the
interface.
【Zoom in】: Enlarge doubled canvas size in the standard state.
【Zoom out】: Click Zoom out in the enlarge canvas, then will restore to standard state canvas.
31
【Adaptive screen】: Display canvas size in 1:1 ratio.
 Click
【Tools】again, the toolbar will be hided.
 Click
every time, the preview interface will add one line canvas, multi-line data can be built to
maximum 16 lines.
 Click
every time, the preview interface will reduce one line canvas.
4.2.4 New Message
【Message】>【New】>【New object】
 Select object enter to the setting interface (text, counter, date time, shift, scan, barcode, local picture)
 After setting parameters, click
【return】to save the object
 Selected object in the object list , click 【Edit object】to modified object ,click
 Click again
to save.
to save message and return to the message management interface.
4.2.4.1 Text object
【Message】>【New】>【New object】>【Text】
 【Input】: Default text content : EXAMPLE TEXT, can enter Chinese, English, numbers, symbols,
other language, 100 characters.
【Character】:
Font: Select the font.
Size: Set the font size.
Font effect:
Bold,
Italic,
Add under horizontal line,
Add font with horizontal
line
Cut Edge: Set whether the objet with white lace.
 【Location】
X axis coordinates: Input range -10-3000mm, you can click
buttons to adjust slightly.
Y axis coordinates: Input range according to canvas amount limited, also can click
adjust slightly.
Width: You can enter 10% to 300%, the greater value, the larger width font.
Height: You can enter 10% to 300%, the greater value, the higher font.
32
buttons to
Lock scale: The proportion of font height and width. After select this function, when modify the font width or
height, the font will be proportionally adjusted.
Tips: If the data location beyond the canvas, it will turn yellow,
after saving only the content within the canvas can be printed.
 【Rotation】
Rotation: Input range 0-359, also can click
buttons to adjust.
Mirror: There are None, Horizontal mirror, Vertical mirror three options, click the drop-down button to
expand
Gradation: Printing darkness can be set within 10-100%.
 【Paragraph】
Spacing: Distance between words, you can enter 0-100, one decimal place
Leading: The distance between two lines. Input range is limited depending on the canvas
Text Alignment Way:
Align multiple lines to the left
Align Multiple lines centering
Align multiple lines to the right
Align multiple lines left and
right justification
 【Name】
It can be set to Chinese, English, numbers and symbols; cannot exceed 30 characters, empty and rename with added
object are not allowed.
4.2.4.2 Counter object
 【Message】>【New】>【New object】>【Counter】
 【Input】: Input contents represents the counter.
 【Routine】:
Initial Value: begin value of the counter, range from -999999999999~+999999999999
Maximum Value: Maximum value, range from -999999999999~+999999999999
Repeat Value: range 0~9999
Step Value: for example: step value set to 3, counter will be 1, 4, 7,11…
33
Carry System: User can select different carry systems, if need to add a new one, click
【Edit】
 System List: Show the default and new built system. It can display a maximum of 5 (including the default base)
 New: Click “new” popup the system editing interface. Enter into the system name and content, click save to save the
system to the list.
 Edit: Selected the system, click “edit” popup the editing interface, click “save” to save the changes. The default system
cannot be edited.
 Select All: All system in the list was chosen; Click the switch again change to all don't choose, all not to choose.
 Delete: Select the newly systems can be deleted. The default system cannot be deleted
 Closing system management: Click on close, out of management interface and save existing system.
 【Advance】:
Carry Source: Click the pull-down menu to check the added counter.
Set the counter which the carry is based on (e.g there are counter 1 and counter 2, set the carry source of counter 2
to be counter 1, then only after counter 1 reached to the maximum value, counter 2 will carry over.)
Current Value: Set the current value of the counter, value should be within the begin value and maximum value.
Repeat Index Value: Set the current repeat index value, only settable while repeat value is not 0, repeat index
value range is 0-repeat value.
Pre-zero: Pre-zero setting of counter, four options: 0001, ___1, 1___, 1.
Alarm: Whether to give an alarm while counter reach the maximum value. User can switch this option on or off.
 【Character】:
Font: Select the font.
Size: Set the font size.
Font effect:
Bold,
Italic,
Add under horizontal line,
line
Cut Edge: Set the objet with/without white edge
34
Add font with horizontal
 【Location】
X axis coordinates: Input range -10-3000mm, you can click
buttons to adjust slightly.
Y axis coordinates: Input range according to canvas amount limited, also can click
buttons to
adjust slightly.
Width: You can enter 10% to 300%, the greater value, the larger width font.
Height: You can enter 10% to 300%, the greater value, the higher font.
Lock scale: The proportion of font height and width. After select this function, when modify the font width or
height, the font will be proportionally adjusted.
Tips: If the data location beyond the canvas, it will turn yellow,
after saving only the content within the canvas can be printed.
 【Rotation】
Rotation: Input range 0-359, also can click
buttons to adjust.
Mirror: There are None, Horizontal mirror, Vertical mirror three options, click the drop-down button to
expand
Gradation: Printing darkness can be set within 10-100%.
 【Paragraph】
Spacing: Distance between words, you can enter 0-100, one decimal place
Leading: The distance between two lines. Input range is limited depending on the canvas
Text Alignment Way:
Align multiple lines to the left
Align multiple lines centering
Align multiple lines to the right
Align multiple lines left and
right justification
 【Name】
You can set Chinese, English, numbers and symbols; not exceed 30 characters, empty and rename with added object
not allowed.
4.2.4.3 Date/Time object
35
 【Message】>【New】>【New object】>【Date/Time】
 【Input】: Input contents represents the date object.
 【Routine】:
Format: select format from the menu, system has 5 default formats, user can define totally 45 types.
The default ones cannot be deleted or modified, default formats include: YYYYMMDD, YYYY/MM/DD,
MM/DD/YYYY, HH:mm, Julian day.
Add new format: if user want to add a new format or modify an exist one, click
,【Edit】 out of date format
management list.
Format List: Display the default formats and newly added formats.
New: Click the new pop-up the date format setting keyboard, can choose a custom date format.
Format name enter no more than 30 characters, and cannot be input (" \ / : *? "< > |"), and can't be
empty, otherwise cannot be saved.
Icons description:
Description
SN
1
4-digit Year
10
2
Last 3-digital Year
11
Minute
3
Last 2-digital Year
12
Second
4
Last 1-digital Year
13
the day of the week
5
Month 01-12
14
6
abbreviated month
15
SN
Icon
36
Icon
Description
Hour in 12 hour
system
Abbreviation of the
weekday
AM/PM
7
Month name
16
Week of Year
8
Day
17
Name of weekday
18
Day of the year
Hour in 24-hour
9
time system
Edit: Choose date from the format list, and click "edit" popup the Settings interface, can modify and then save. The
default format cannot be modified!
Select all: All formats in the list was chosen; Click the switch again change to all don't choose, all not to choose.
Delete: Select the data format can be deleted. The default format cannot be deleted
Closing date format management: Click on close, out of date format management interface and save existing format.
Expiry date: If only want to add a production date, user may need to set the expiry day to 0; expiry
time can switch from day, week, month, year, value within 0-999.
Calendar type: Gregorian/ Hirji
Pre-zero: 4 choices: 2015/01/01, 2015/_1/_1, 2015/1_/1_, 2015/1/1\
 【Date/Time】:
Zero Setting: Enable the Zero Setting, Input the time (hour: 0-23; minute: 0-59)
Day Time Saving: User can select from OFF, Europe or America.
 【Character】:
Font: Select the font.
Size: Set the font size.
Font effect:
Bold,
Italic,
Add under horizontal line,
Add font with horizontal
line
Cut Edge: Set whether the objet with white lace.
 【Location】
X axis coordinates: Input range -10-3000mm, you can click
buttons to adjust slightly.
Y axis coordinates: Input range according to canvas amount limited, also can click
buttons to
adjust slightly.
Width: You can enter 10% to 300%, the greater value, the larger width font.
Height: You can enter 10% to 300%, the greater value, the higher font.
Lock scale: The proportion of font height and width. After select this function, when modify the font width or
37
height, the font will be proportionally adjusted.
Tips: If the data location beyond the canvas, it will turn yellow,
after saving only the content within the canvas can be printed.
 【Rotation】
Rotation: Input range 0-359, also can click
buttons to adjust.
Mirror: There are None, Horizontal mirror, Vertical mirror three options, click the drop-down button to
expand
Gradation: Printing darkness can be set within 10-100%.
 【Paragraph】
Spacing: Distance between words, you can enter 0-100, one decimal place
Leading: The distance between two lines. Input range is limited depending on the canvas
Text Alignment Way:
Align multiple lines to the left
Multiple lines align centered
Align multiple lines to the right
Align multiple lines around
 【Name】
It can be set to Chinese, English, numbers and symbols; cannot exceed 30 characters, empty and rename with added
object are not allowed.
4.2.4.4 Shift object
 【Message】>【New】>【New object】>【shift】
 【Input】: Input contents represents the shift object.
 【Routine】:
Shift: From the pull-down menu, user can check the already existed shifts, if need to create a new one
or modify any of them, click
【Edit】
38
Shift List: Show the default and new built shift.
New: Building new shift
Shift
content list
 【Interval】: According to the selected time interval, 24 hours a day is divided into the corresponding number of
shifts. For example, the time interval is set to 4H, the system automatically generates 6 shifts (default A-F), and shows
in the left list.
 【Start Time】: Time of first shift. For example, set the interval to 4H, the starting time is set to 8:00, then the
first shift A start time is 8:00, shift B start time is 12:00, shift C start time is 16:00, and so on.
 【Set】: Select the time interval and the start time, click the button【Set】, will generate the default shifts
automatically, and shows in the left list.
 【add】:If need to add another shift, you can input the 【shift name】 and the 【time】, click
the new shift will be added to the list on the left side.
 【shift content list】: Show the current team all content; Maximum user can add 48 shifts.
 【delete】: If need to delete any shift, select that one in the list, click
 【delete all】:If need to delete all exist shifts, click
39
【Delete All】
【Delete】
【Add】,
【Modify Shift Content】: select the shift from the list on the left, then edit its content on the right side,【Add】
will change to【Modify】,click【Modify】to save
 【shift name】: Maximum 30 characters, can be Chinese, English letters, numbers or symbols (no special
symbols).
 【Save shift】: Click
to save.
Edit: Selected the shift from the 【shift list】, click “edit” popup the editing interface, click “save” to
save the changes. The default shift cannot be edited.
Select All: All shifts in the list was chosen; Click the switch again change to all don't choose, all not
to choose.
Delete: Select the newly shifts can be deleted. The default shift cannot be deleted
Closing Shift Management: Click on close, out of management interface and save existing shifts.
 【Character】:
Font: Select the font.
Size: Set the font size.
Font effect:
Bold,
Italic,
Add under horizontal line,
Add font with horizontal
line
Cut Edge: Set whether the objet with white lace.
 【Location】
X axis coordinates: Input range -10-3000mm, you can click
buttons to adjust slightly.
Y axis coordinates: Input range according to canvas amount limited, also can click
buttons to
adjust slightly.
Width: You can enter 10% to 300%, the greater value, the larger width font.
Height: You can enter 10% to 300%, the greater value, the higher font.
Lock scale: The proportion of font height and width. After select this function, when modify the font width or
height, the font will be proportionally adjusted.
Tips: If the data location beyond the canvas, it will turn yellow,
after saving only the content within the canvas can be printed.
 【Rotation】
Rotation: Input range 0-359, also can click
buttons to adjust.
40
Mirror: There are None, Horizontal mirror, Vertical mirror three options, click the drop-down button to
expand
Gradation: Printing darkness can be set within 10-100%.
 【Paragraph】
Spacing: Distance between words, you can enter 0-100, one decimal place
Leading: The distance between two lines. Input range is limited depending on the canvas
Text Alignment Way:
Align multiple lines to the left
Multiple lines align centered
Align multiple lines to the right
Align multiple lines around
 【Name】
It can be set to Chinese, English, numbers and symbols; cannot exceed 30 characters, empty and rename with added
object are not allowed.
4.2.4.5 Scan print object
 【Message】>【New】>【New object】>【scan print】
 【Input】: Input contents represents the scan object.
 【Routine】:
Auto Sleep: Make the device into the low power state. Default value is 1s, the range is 1-60s.
Read Time: Default value is 3s, the range is 0-3600s.
Error Info: Need to turn on the right switch before use. Only support for input in English.
 【Character】:
Font: Select the font.
Size: Set the font size.
Font effect:
Bold,
Italic,
Add under horizontal line,
line
Cut Edge: Set whether the objet with white lace.
 【Location】
41
Add font with horizontal
X axis coordinates: Input range -10-3000mm, you can click
buttons to adjust slightly.
Y axis coordinates: Input range according to canvas amount limited, also can click
buttons to
adjust slightly.
Width: You can enter 10% to 300%, the greater value, the larger width font.
Height: You can enter 10% to 300%, the greater value, the higher font.
Lock scale: The proportion of font height and width. After select this function, when modify the font width or
height, the font will be proportionally adjusted.
Tips: If the data location beyond the canvas, it will turn yellow,
after saving only the content within the canvas can be printed.
 【Rotation】
Rotation: Input range 0-359, also can click
buttons to adjust.
Mirror: There are None, Horizontal mirror, Vertical mirror three options, click the drop-down button to
expand
Gradation: Printing darkness can be set within 10-100%.
 【Paragraph】
Spacing: Distance between words, you can enter 0-100, one decimal place
Leading: The distance between two lines. Input range is limited depending on the canvas
Text Alignment Way:
Align multiple lines to the left
Multiple lines align centered
Align multiple lines to the right
Align multiple lines around
 【Name】
It can be set to Chinese, English, numbers and symbols; cannot exceed 30 characters, empty and rename with added
object are not allowed.
4.2.4.6 Barcode object
【Message】>【New】>【New object】>【Barcode】
【Input】: Enter barcode text content.
42
【Type】:
Genre: Select 1Dbarcode, 2D barcode.
Type: Select barcode type.
【Specification】:
Note: 1D and 2D barcodes have different settings, user need to select barcode
genre firstly.
Barcode type
1D Barcode
Settings
Width: Totally 1-16 levels to choose from.
Height: Within the canvas size,1-12.7mm
Font: Select barcode text font
Font Size: Select barcode text font size.
Text Display: User can switch from on or off.
Cut Edge: Select barcode whether with white lace
Blank Level: 0-4 grades to switch.
2D Barcode
Width: Totally 1-16 levels to choose from.
Error Correction Level: QR code, 1-4 grades;
PDF417, 1-7 grades.
Blank Level: 0-4 grades to switch.
Size:
QR/DATAMATRIX
bar
code
size
specifications.
 【Location】
X axis coordinates: Input range -10-3000mm, you can click
buttons to adjust slightly.
Y axis coordinates: Input range according to canvas amount limited, also can click
buttons to
adjust slightly.
Width: You can enter 10% to 300%, the greater value, the larger width font.
Height: You can enter 10% to 300%, the greater value, the higher font.
Lock scale: The proportion of barcode height and width. After select this function, when modify the font width or
height, the font will be proportionally adjusted.
Tips: If the data location beyond the canvas, it will turn yellow,
after saving only the content within the canvas can be printed.
43
 【Rotation】
Rotation: Input range 0-359, also can click
buttons to adjust.
Mirror: There are None, Horizontal mirror, Vertical mirror three options, click the drop-down button to
expand
Gradation: Printing darkness can be set within 10-100%.
 【Name】
It can be set to Chinese, English, numbers and symbols; cannot exceed 30 characters, empty and rename with added
object are not allowed.
4.2.4.7 Logo object
【Message】>【New】>【New object】>【Logo】
【Routine】: Select from the picture list
【Location】
X axis coordinates: Input range -10-3000mm, you can click
buttons to adjust slightly.
Y axis coordinates: Input range according to canvas amount limited, also can click
buttons to
adjust slightly.
 【Rotation】
Rotation: Input range 0-359, also can click
buttons to adjust.
Mirror: There are None, Horizontal mirror, Vertical mirror three options, click the drop-down button to
expand
Gradation: Printing darkness can be set within 10-100%.
 【Specification】
Width: You can enter 10% to 300%, the greater value, the larger width pic
Height: You can enter 10% to 300%, the greater value, the higher pic.
Lock scale: The proportion of pic height and width. After select this function, when modify the font width or
height, the font will be proportionally adjusted.
 【Name】
It can be set to Chinese, English, numbers and symbols; cannot exceed 30 characters, empty and rename with added
object are not allowed.
44
4.2.5 Edit Message
 Click【Message】from the main interface, then click【List】to see all the messages added.
 Select the message, and click【Edit】
 After editing, click return, choose save or not.
Tips:When the MSG with dynamic source (Counter, Device Info, Date Time, Scan, Shift) has
print records, edit this MSG and save it, will prompt to 【Save】【Not Save】【Save As】【Cancel】options.
Select 【Save As】to retain the original MSG, and create a new MSG. Select 【Save】, the original MSG will
be covered, the print records is cleared and cannot be reprinted.
4.2.6 Copy/Paste Message
Select the message in list, click
【Copy】, and then click any position in the list, click
【Paste】,
the message will be copied and named as the original one with “C1” at the end. For example, if original
message is MSG001, the copied one will be named as “MSG001C1”.
 Can do multiple choice, copy and paste them at the same time.
 If copied several times, only the last copied message(s) will be pasted.
4.2.7 Delete Message
Select the message(s) in the list, click 【Delete】, yes to delete or no to cancel.
4.3 Printing Management
4.3.1 Start/Stop Printing
【Print】>【List】, refer to List Function
45
 Select the message, and click
【Start】
 After start printing, printing report will pop up, 【Start】button change to【Stop】, then after get the
sensor signal, message will be printed.
 Click【Stop】, printing report will disappear, button will go back to【Start】.
4.3.2 Printing Report Display
 While printing is on, user will see the below information from the printing report:
Left: Message name, counter, system time.
Middle: Dynamic source content in printing (only when counter, shift included in the message).
Right: Scan content, next printing content (only display while printing scanning information.)
 Report content changes according to real time printing status.
 Click the top arrow will hide the report, click again will display.
4.3.3 Printing Delay
Printing Delay: It is the distance from the point when photocell senses the printing object to the point
when printing starts. User can adjust the value to alter the print position on printing object.
【Print】>【Delay】
 Value within 0-1000mm, down to the first decimal point. Click
previous menu, or click
to quit without saving.
 Setting modification will be valid from next printing message.
 Delay value also can be set after printing started.
46
, save the setting and go back to
4.3.4 Initial Setting
Note: This function only valid while message contains counter /text source. After printing started,
this setting is not settable.
【Print】>【Initial】
 Set the current value, index value of counter.
Current Value: the value will be printed after start printing, value need to be within the begin value and end
value.
System: User can choose the system in the pull-down menu.
Repeat Index Value: The next printing is the Nth time of the repeat value. The repeat value of counter source
need to be nonzero.
 Set the text source, can modify the text content, the next printing content will be changed after saving
the settings.
 After setting the current value, click
to save, valid from next printing, or click
【Cancel】
to exit.
4.3.5 Printing Monitor
After start printing of a message which contains dynamic source (counter , scan, shift, date time, device
info), click【Monitor】 to check printing data and coming data.
47
 Dynamic source information will be displayed by sequence, user may pull down the menu to check if
data quantity more than 5pcs.
 The display sequence can be manually selected: click
 Click
【Pull down】, select the data.
【Off】, will close the monitor.
 Monitor information has a real time updating.
 The print monitor list display is determined by the print cache. For example, if print cache is set to 10,
the list of monitor shows 10 records.
4.3.6 Re-print
Tips: Reprint is invalid if the message without dynamic source (counter, scan, shift, date time,
device info).
Reprint function is available only when the message with the dynamic source is printed at least once.
 【Message】>【Reprint】
 Start/Stop printing, click
 Long press the button
【Reprint】to reprint the last message.
【Reprint】, go to the reprint interface.
 Select the records you want to reprint in the list, click
48
【Reprint】, can print the selected records.
 Select the record in the list, click
【Preview】button, can preview the selected record.
4.4 Print Parameter
4.4.1 Print Setting
Print Direction: set the printing direction of the printhead: L To R (from left to right), and R To L
(from right to left).
Mirror: three options: None, Horizontal and Vertical.
DPI:
Printing resolution, range from 50-600.
4.4.2 Printhead Setting
Nozzle switch: Two lines of nozzles of each printhead (left, right); user can select to use
left/right/double nozzle(s). (Note: use single channel will save half ink drops, so the darkness will be
lighter).
Pre-purge: When Pre-purge function is ON, printer will spray a little ink at optioned level during
idle period in printing process to keep nozzle plate warm and moist so as to eliminate dried ink phenomenon.
Five levels to choose from: Close, Low, Middle, High, and Custom.
 Default setting is Close.
 While setting is low, middle or high, pre-purge parameters will be set automatically according to the ink type.
 While setting is Custom, user can set the interval from 1 to 3600. For example, input 10 seconds, after start the
printing and before sensor signal, every 10 seconds printer will spit some ink drops to make nozzles wet.
4.4.3 Printing Option
Output Counter: numbers already printed. After being modified, counter will run based on the
new value.
49
Counter Reset: Every time user print a message which contains a counter, system will ask if to reset
the counter after this printing, if select “Yes”, then from next printing counter will run from the minimum
value, if select “No”, counter will continue from current value.
Print Cache: Message quantity saved in system memory, value can be1-20, if set to 1, will print
by real time.
Blank Line No Print: Message contains empty lines, open the blank line no print function, No
printing blank line.
4.4.4 Special Printing
Continuous printing: Continuous printing numbers, range from 0-9999, 0 means OFF, 9999
means unlimited; If set value to N(within 1-9998), then after get one sensor signal, N pieces messages will
be printed.
Printing Interval: The distance from the beginning of the first message to the beginning of the
second message. Default value is 0mm, range from 0-9999.99mm.
4.5 System setting
4.5.1 System management
System time:
Year
2001-2999
Month
Day
Hour
Min
Second
1-12
1-31
0-23
0-59
0-59
Unit: 【mm or inch】click the icon to select unit.
Language: 【English and others】. Click the icon to select language.
 Default language: English How to upgrade other language, please refer to How to upgrade language, fonts and input
method
 After switching language, printer will restart automatically.
Device name: Allow 30 characters. When message contains device name source, the message will
change after the device name is changed.
Screensavers: System default 3 min, 5 options for changeover: 1 min, 3 min, 5 min, 30 min,
50
OFF. If screen saver is optioned OFF, screen enters standby status if inactive for the set time. Screen
becomes active when there’s alarm or error.
Screen brightness: User can set the brightness from 10-100%, default is 30%.
Message Mode: Select message management mode, standard mode or simple mode.
4.5.2 User management
It allows administrator to assign rights of operation.
Open user management feature
【System】>【User management】
 Default status is closed, click the icon and it will jump out a page to input the password. The default
password is 888888.Click “√”to open and click “×”to close.
Create new user
 After opening user management feature, click
to create new user.
Create user info
 User name: No more than 30 characters, cannot be empty.
 Password: No more than 16 digits.
 Confirm password: Should be the same as previous one.
51
Create new user Rights
 Click
to get into new user rights setting page.
 It has 6 rights for new users.
Items
Print
Features available
Start/stop printing, Printing delay, Initial, Printing Monitor, and Reprint
Direction, Mirror, Nozzle, DPI, Output, Pre-purge, Counter reset,
Parameter
Cache, Special、Blank line no print
Message
New message, Edit message, Copy, Paste, Delete
Setting
Setting, User control, About
Tools
Image, Upgrade, Backup /Restore, Permission, and Plugin Management
【Print】: All
Operator
【Setting】: User control and About
【Print】: All; 【Parameter】: All, 【Message】: All;
Technician
【Setting】: User control and About.
Tips:
 Select multiple options is available, repeat select will delete selected option.
【System reset】feature in【System】is only allowed to be modified by administrator.
【User control】 by new user can only do its own password change, cannot do anything else.
 Click
【Operator】, can select its rights(See operator power list above)
 Click
【Technician】, can select its rights(See technician power list above)
52
 Click
【All】, can select all rights.
 Click
【None】, cancel all rights.
 After setting new user info and rights, please click “√”to save.
 After saving, new user info will be displayed in the list.
Edit user info and rights
Open user management, select the user info you want to edit (Administrator not included), click
and do the edit and save.
Change user password
Open user management, select the user info you want to edit and click
to change password.
Tip: After logging user management, it can only change current user password.
Delete user info
Open the user management, select user info and click
to delete user info.
Tip: Cannot delete Administrator.
Close user management
Open user management, it will jump out a page requiring to input password, after inputting correct
administrator password, and click“√”,the icon will turn grey to close user management.
Log in /Log out
 Open user management, click
, it will jump out a page. Inputting the correct user name and
password to log in.
 Open the user management, every time opening the printer, it requires to log in first.
4.5.3 System Reset
If required to restore back to factory setting, you can do system reset.
【System】>【System Reset】
53
 Click
, all options are selected automatically.
 Click
, all selected options are deleted.
 After selected, click
【Reset】, it will jump out a page requiring to input administrator password.
Then the printer will restart automatically.
Items can be reset:
Module
Items
Parameters
Message
Message list
Clear
Image
Image list
Clear
Printing direction
R To L
Mirror
None
Nozzle switch
Left nozzle
DPI
300
Production counter
0
Spit function
Closed
Counter reset
Closed
Printing buffer
20
Blank Line No Print
Closed
Continuous printing
0
Printing gap
1
System time
Default time
Unit
mm
Device name
INKJET
Screensavers
3mins
Screen brightness
30
Message Mode
Standard Mode
User control
Closed
Language
Language management
English
Font
Font management
default
Input
Input management
English
Printing parameters
System parameter
54
4.5.4 About
【System】>【About】
Display company name, website, company logo, software version, hardware version, device SN, and
customer code.
4.6 Tools
4.6.1 How to manage local images
【Tools】>【Image】
Preview image
Select images and it will show images for preview.
Import images
 Insert USB with images, click
to import images.
 If pixels are more than 150*10000, it will import failure.
 100 images maximum.
55
 Import picture format: bmp/jpg/png/gif
Export images
Insert USB and click
to export images, the default path is(Inkjet/Logo/ )
Delete images
Select images and click
to delete images.
All selected
Click
to select all.
Cancel selection
Click
to cancel selection.
4.6.2 How to upgrade language/font/typewriting
【Tools】>【Upgrade】
Upgrade language
 Insert USB with language file (File stores in USB under: Inkjet\Upgrade\Language)
 Click
to select language, the list shows the upgraded language, the default is only English.
 Click
【upgrade】 to select language from USB and after upgrade, the printer will restart.
 Can upgrade 3 different languages. Click 【Delete】 to delete language.
Upgrade font
 Insert USB with font file (File stores in USB under: Inkjet\Upgrade\Font)
 Click
【Font】 to select font, the list shows the upgraded font, default is the base.
56
 Click
【Upgrade】to select font from USB to upgrade and after upgrade, the printer will restart.
 Can upgrade 3 fonts, click【Delete】to delete font
Upgrade Input method
 Insert USB with font file (File stores in USB under: Inkjet\Upgrade\Keyboard\)
 Click
【Input】 to select input method, the list shows the upgraded input method, the default is
English.
 Click
【Upgrade】to select input method from USB to upgrade and after upgrade, the printer
will restart.
 Can upgrade 3 input methods, click【Delete】to delete.
4.6.3 Permission
Some features need to be registered before use.
【Tools】>【Permission】
Register
Insert USB with registration file, click
to select file to do registration.
Precaution:
 Can register more features in one printer.
 If registration code is expired, the registration icon will disappear and you need to do registration
again.
Select All
57
 Click
【Select All】, all features in the list are checked, can be deleted.
Delete registration
 Click
to delete registration.
4.6.4 Plugin Management
 Insert USB with plug-in file, click
【Add】to select file to add plugin, after add plugin
successfully, shows in the list.
 Click
【Select All】, all plugins in the list are checked.
 Click
【Delete】to delete the selectable plugin in the list.
4.7 Status bar
4.7.1 Cartridge status
Click
to display cartridge status.
58
Cartridge icon color
Grey: No cartridge
Green: Normal
Orange: Ink ran up to 95%--warning
Red: Empty cartridge or error cartridge
Display cartridge info
Ink status, Cartridge SN, Client Code, Ink type, Volume, Used percentage, Data points
Clean printhead
Click
to clean printhead when it is not printing.
4.7.2 System status
Click
to display system status
System status color
Green: Normal
Red: System time reset, FPGA error, etc.
Display system info
System status, MSG name, Direction, Print nozzle switch, DPI, Output, Pre-purge, Print cache, Times
(Continuous printing), Interval, and Mirror.
4.7.3 Encoder information
Displays encoder connection status, when encoder is connected, click
59
icon, encoder signal test
interface appears.
4.7.4 Photocell information
Displays photocell connection status, when photocell is connected, click
icon, encoder signal test
interface appears.
Currents Status: Press the print switch, the current status shows OPEN, release the print switch, the
current status shows OFF.
4.7.5 USB Status
 After USB inserted, click
to display USB status.
USB info: USB volume, USB space occupied, USB space remained.
4.7.6 Battery Indicator
60
Green: The remaining power is 20%-100%
Yellow: The remaining power is 10%-20%
Red: Low battery, it means the battery is less than 10%
Precaution: when battery is low, please recharge ASAP.
4.7.8 WI-FI Status
Display WI-FI connection status as unconnected
 Click
(gray) and normally connected
(green).
Wi-Fi interface appears (Default is turn off, and the list is empty).
 Turn on WLAN, scan Wi-Fi device automatically and display the scan results in the list.
 Clip the switch and turn on, the system will search the network automatically, and display in the list;
You also can manually click【Search】button to find the network.
 Click a Wi-Fi device, pop-up password input box, enter the correct password to connect to the wireless
network. (Note: Click a no password WI-FI can be connected automatically.)
4.7.8 Log out
Please refer to Log in /Log out.
4.8 Input Method Introduction
On the keyboard, user can input capital letter, lowercase letter, numbers, common symbols, Chinese,
Spanish.
Lowercase letter: default keyboard is lowercase letters, displayed as below:
61
Capital letter: shift by
Numbers: shift by
Symbols: click
to shift to symbols; click
shift to Chinese symbols.
62
Chinese: Click
to shift from Chinese and English; Chinese typing only workable
while system language is Chinese.
Spanish: Change the system language to Spanish, long-press a,e, i, o, u, n, system will pop-up the
corresponding symbols.
【Cancel】close keyboard, quit without save
【Enter】close keyboard and save
63
【Delete】delete the type, long-press will delete all the content in the input box.
【Newline】input in next line.
64
Appendix 1: Terms and Definition
SN
1
Term
Print delay
Description
To adjust the distance from the time
when photocell detected the object till
printing.
2
Initial value
Initial value from printing
3
Time change
Users can set day switch time
4
5
Pre-purge
Printhead
cleaning
Nozzle switch
To avoid printhead clogged
To clean printhead
Switch nozzle to get better print result.
Continuous
printing
Screen saver
time
Multi-printing during the time from
photocell begins and ends
To shut down screen to save electricity
power.
6
7
8
65
Remark
If set delay distance as 30mm,
then it will start to print after
30mm later when photocell
detect the object
For example, if set initial
value as 9, the first print value
is 9
When set day switch as
“08:00” July 10, then the
time is 07:59 July 09 for all
printing before /on“07:59”
To avoid printhead clogged
To clean printhead
Switch nozzle to get better
print result.
For example, if set screen
saver time as 0.5H, if no more
operation within 0.5H, the
screen will be shut down.
Download PDF