TGAR-1062/2062/1662 Series
IEEE 802.11 a/b/g/n Access Point Router
User Manual
Version 1.0
Feb, 2014
www.oring-networking.com
TGAR-1062/2062/1662 Series User Manual
COPYRIGHT NOTICE
Copyright © 2014 ORing Industrial Networking Corp.
All rights reserved.
No part of this publication may be reproduced in any form without the prior written consent of
ORing Industrial Networking Corp.
TRADEMARKS
is a registered trademark of ORing Industrial Networking Corp.
All other trademarks belong to their respective owners.
REGULATORY COMPLIANCE STATEMENT
Product(s) associated with this publication complies/comply with all applicable regulations.
Please refer to the Technical Specifications section for more details.
WARRANTY
ORing warrants that all ORing products are free from defects in material and workmanship for a
specified warranty period from the invoice date (5 years for most products). ORing will repair or
replace products found by ORing to be defective within this warranty period, with shipment
expenses apportioned by ORing and the distributor. This warranty does not cover product
modifications or repairs done by persons other than ORing-approved personnel, and this
warranty does not apply to ORing products that are misused, abused, improperly installed, or
damaged by accidents.
Please refer to the Technical Specifications section for the actual warranty period(s) of the
product(s) associated with this publication.
DISCLAIMER
Information in this publication is intended to be accurate. ORing shall not be responsible for its
use or infringements on third-parties as a result of its use. There may occasionally be
unintentional errors on this publication. ORing reserves the right to revise the contents of this
publication without notice.
CONTACT INFORMATION
ORing Industrial Networking Corp.
3F., No.542-2, JhongJheng Rd., Sindian District, New Taipei City 23148, Taiwan (R.O.C.)
Tel: +886-2-2218-1066 // Fax: +886-2-2218-1014
Website: www.oring-networking.com
Technical Support
E-mail: support@oring-networking.com
Sales Contact
E-mail: sales@oring-networking.com (Headquarters)
sales@oring-networking.com.cn (China)
ORing Industrial Networking Corp.
1
TGAR-1062/2062/1662 Series User Manual
Tables of Content
Getting Started............................................................................................... 1
1.1
About TGAR-1062/2062/1662 Series...................................................................... 1
1.2
Software Features .................................................................................................. 1
1.3
Hardware Features................................................................................................. 2
2.1
Front Panel ............................................................................................................ 3
2.1.1
Ports and Connectors ......................................................................................... 3
2.1.2
Front Panel LEDs ............................................................................................... 5
2.2
Side Panel.............................................................................................................. 5
2.2
Top Panel ............................................................................................................... 6
2.3
Bottom Panel.......................................................................................................... 7
Hardware Installation .................................................................................... 8
3.1
Wall Mounting Installation ....................................................................................... 8
3.2
Wiring................................................................................................................... 11
3.2.1
Grounding ............................................................................................................ 11
3.2.2
Fault Relay ........................................................................................................... 11
3.2.3
Redundant Power Inputs ...................................................................................... 12
Cables and Antenna .................................................................................... 13
4.1
Ethernet Pin Definition .......................................................................................... 13
4.2
Console Port Pin Definition ................................................................................... 13
4.3
DI/DO ................................................................................................................... 14
4.4
Wireless Antenna ................................................................................................. 14
4.5
Cellular Antenna ................................................................................................... 15
Management ................................................................................................ 16
5.1
Network Connection ............................................................................................. 16
5.2
Configuration ........................................................................................................ 17
5.2.1
Basic Setting .................................................................................................... 17
WAN......................................................................................................................... 18
LAN .......................................................................................................................... 22
DHCP ....................................................................................................................... 22
Wireless AP .............................................................................................................. 24
DDNS ....................................................................................................................... 30
Date & Time ............................................................................................................. 30
5.2.2
Networking Setting ........................................................................................... 31
Wireless Setting – Advanced Setting......................................................................... 31
Wireless Setting – MAC Filter ................................................................................... 33
NAT Setting - Virtual Server ...................................................................................... 34
NAT Setting – DMZ ................................................................................................... 35
NAT Setting – UPnP ................................................................................................. 35
ORing Industrial Networking Corp.
2
TGAR-1062/2062/1662 Series User Manual
Firewall Setting – IP Filter ......................................................................................... 36
Firewall Setting – MAC Filter..................................................................................... 37
Vpn Setting – Open Vpn ........................................................................................... 38
Vpn Setting – PPTP VPN.......................................................................................... 40
Vpn Setting – PPTP Client ........................................................................................ 42
VRRP ....................................................................................................................... 43
Routing Protocol – Routing Setting ........................................................................... 45
5.2.3
System Tools.................................................................................................... 48
Login Setting ............................................................................................................ 48
Router Restart .......................................................................................................... 48
Firmware Upgrade .................................................................................................... 49
Save/Restore Configurations .................................................................................... 49
Miscellaneous........................................................................................................... 50
Event Warning .......................................................................................................... 50
E-mail ....................................................................................................................... 52
DIDO ........................................................................................................................ 54
5.2.4
System Status .................................................................................................. 55
System Info .............................................................................................................. 55
System Log .............................................................................................................. 55
Traffic Statistics ........................................................................................................ 55
Wireless Link List...................................................................................................... 56
Technical Specifications ............................................................................. 57
Compliance ............................................................................................ 62
ORing Industrial Networking Corp.
3
TGAR-1062/2062/1662 Series User Manual
Getting Started
1.1 About TGAR-1062/2062/1662 Series
Designed
for
industrial
and
rolling
stock
wireless
applications with two LAN ports in M12 connectors and
EN50155 compliance, the ORing TGAR-1062/2062/1662
series are IEEE802.11 a/b/g/n routers capable of providing
a fast and effective way to communicate with the Internet
over wired or wireless LANs. Consisting of 3G and 4G
models, the series of devices can be configured to operate
in 3 modes of routing function: dynamic/static IP route,
PPPoE authentication, and cellular modem dial up. Users
can set up WLAN environment to fulfill demands of various applications rapidly by dialing up
cellular modem. With dual Ethernet ports in switch mode, you can use Daisy Chain to reduce
the usage of Ethernet switch ports. The router also provides VPN capabilities which create
encrypted virtual tunnels on the Internet, allowing remote or mobile users to connect to the
network of your office.
1.2
Software Features
 High-speed air connectivity for up to 300Mbps
 High security with support for WEP/WPA/WPA-PSK(TKIP,AES)/
WPA2/WPA2-PSK(TKIP,AES)/802.1X authentication
 Secure management by HTTPs
 Various kinds of WAN connections supported, including dynamic/static IP, PPPoE, and
modem dial up
 Configurable IP tables to prevent unauthorized access
 Supports VPN for secure network connection (Open VPN , PPTP VPN)
 Supports NAT setting (virtual server , port trigger , DMZ , UPnP)
 Supports DHCP forwarding through PPTP
 3.5G HSDPA modem dial up (3G models)
 4G LTE modem dial up (4G models)
 Supports redundant mode (Recovery time < 10ms) and switch mode in M12 connector
(A-coding)
 Wireless connection status monitoring
 Event warning by Syslog, e-mail, SNMP trap, and relay output
ORing Industrial Networking Corp.
1
TGAR-1062/2062/1662 Series User Manual
1.3
Hardware Features
 2 x 10/100/1000 Base-T(X) Ethernet ports in M12 connectors
 2 x WLAN antenna connectors (TGAR-1062/2062 series) or 4 x WLAN antenna connectors
(TGAR-1662 series)
 1 x cellular antenna connectors (TGAR-1062/1662 series) or 2 x cellular antenna
connectors (TGAR-2062 series)
 EN50155 compliance
 Redundant power inputs: 12~48 VDC
 Casing: IP-40
 Dimensions: 125.6mm (W) x 65mm (D) x 196.1mm (H) (4.94 x 2.55 x 7.72 inch)
 Operating temperature: -25 to 70°C
 Storage temperature: -40 to 85°C
 Operating humidity: 5% to 95%, non-condensing
 Wall mounting enabled
ORing Industrial Networking Corp.
2
TGAR-1062/2062/1662 Series User Manual
Hardware Overview
2.1 Front Panel
2.1.1 Ports and Connectors
The series is equipped with the following ports and features on the front panel.
Port
Description
10/100/1000 Base-T(X) Ethernet ports
2 x 10/100/1000 Base-T(X) ports supporting
with M12 connectors (D-coding)
auto-negotiation.
Relay output with M12 (A-coding)
1 x relay output to carry capacity of 1A at 24VDC
connector
M23 power connector with redundant
power inputs
DIDO with M12 connector (D-coding)
Dual power inputs for 12~48 VDC
4 x digital input / 4 x digital output
TGAR-1062 Series
ORing Industrial Networking Corp.
3
TGAR-1062/2062/1662 Series User Manual
TGAR-2062 Series
TGAR-1662 Series
ORing Industrial Networking Corp.
4
TGAR-1062/2062/1662 Series User Manual
1. Power status LED
7. Console & Backup unit port
2. LAN port status LED
8. Ethernet LAN ports
3. Fault status LED
9. DI/DO ports
4. WAN status LED
10. Power connector
5. WLAN status LED
11. 2.4/5GHz antenna
6. Relay output port
12. Cellular antenna connector
13. SIM card slot
2.1.2 Front Panel LEDs
LED
Color
Status
Description
PWR1
Green
On
DC power 1 activated.
PWR2
Green
On
DC power 2 activated.
ETH1
Green
On
Port is linked
Blinking
Data transmitted.
On
Port is linked
Blinking
Transmitting data
On
Port is linked
On
WLAN is activated
Blinking
Transmitting data
Green
ETH2
Green
WLAN 1 (2)
Green
WAN1 (2)
Green
On
Modem is connected
Fault
Red
On
Error occurs (power fails or port disconnected)
2.2 Side Panel
1. Antenna connector
2. Reset button
ORing Industrial Networking Corp.
5
TGAR-1062/2062/1662 Series User Manual
Note: to restore the device configurations back to the factory defaults, press the Reset button
for a few seconds. Once the power indicator starts to flash, release the button. The device will
then reboot and return to factory defaults.
2.2 Top Panel
On the top panel sits a SIM card slot and a cellular antenna connector, as show as below.
TGAR-1062/1662 Series
TGAR-2062 Series
ORing Industrial Networking Corp.
6
TGAR-1062/2062/1662 Series User Manual
2.3 Bottom Panel
TGAR-2062 Series
ORing Industrial Networking Corp.
7
TGAR-1062/2062/1662 Series User Manual
Hardware Installation
Elevated Operating Ambient: If installed in a closed environment, make sure the
operating ambient temperature is compatible with the maximum ambient
temperature (Tma) specified by the manufacturer.
Reduced Air Flow: Make sure the amount of air flow required for safe operation of
the equipment is not compromised during installation.
Mechanical Loading: Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading: Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might
have on overcurrent protection and supply wiring. Appropriate consideration of
equipment nameplate ratings should be used when addressing this concern.
3.1 Wall Mounting Installation
TGAR-1062 Series Wall-mount Kit Measurement
ORing Industrial Networking Corp.
8
TGAR-1062/2062/1662 Series User Manual
TGAR-2062 Series Wall-mount Kit Measurement
ORing Industrial Networking Corp.
9
TGAR-1062/2062/1662 Series User Manual
TGAR-1662 Series Wall-mount Kit Measurement
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1: Hold the router upright against the wall
Step 2: Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Step 3: Slide the router downwards and tighten the four screws for added stability.
ORing Industrial Networking Corp.
10
TGAR-1062/2062/1662 Series User Manual
Instead of screwing the screws in all the way, it is advised to leave a space of
about 2mm to allow room for sliding the switch between the wall and the screws.
3.2 Wiring
WARNING
Be sure to switch off the power and make sure the area is not hazardous
before disconnecting modules or wires. The devices may only be connected to
the supply voltage shown on the type plate.
3.2.1
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the ground pin on the power connector to the
grounding surface prior to connecting devices.
3.2.2
Fault Relay
The router uses a M12 A-coded 5-pin male connector on the front panel for relay output. Use
a power cord with an M12 A-coded 5-pin female connector to connect the relay. The relay
contacts will detect user-configured events and form an open circuit when an event is
triggered.
ORing Industrial Networking Corp.
11
TGAR-1062/2062/1662 Series User Manual
3.2.3
Redundant Power Inputs
The device supports two sets of power supplies and uses the M23 5-pin female connector on
the front panel for the dual power inputs.
Step 1: Insert a power cable to the power connector on the device.
Step 2: Rotate the outer ring of the cable connector until a snug fit is achieved. Make sure
the connection is tight
ATTENTION
1. Be sure to disconnect the power cord before installing and/or wiring your
routers.
2. Calculate the maximum possible current in each power wire and
3.
4.
5.
6.
common wire. Observe all electrical codes dictating the maximum
current allowable for each wire size.
If the current goes above the maximum ratings, the wiring could
overheat, causing serious damage to your equipment.
Use separate paths to route wiring for power and devices. If power
wiring and device wiring paths must cross, make sure the wires are
perpendicular at the intersection point.
Do not run signal or communications wiring and power wiring through
the same wire conduit. To avoid interference, wires with different signal
characteristics should be routed separately.
You can use the type of signal transmitted through a wire to determine
which wires should be kept separate. The rule of thumb is that wiring
sharing similar electrical characteristics can be bundled together
7. You should separate input wiring from output wiring
8. It is advised to label the wiring to all devices in the system
ORing Industrial Networking Corp.
12
TGAR-1062/2062/1662 Series User Manual
Cables and Antenna
4.1 Ethernet Pin Definition
The routers have two 10/100/1000 Base-T(X) Ethernet ports. According to the link type, the
AP uses CAT 3, 4, 5, 5e, UTP cables to connect to any other network device (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable specifications.
Cable
Type
Max. Length
Connector
10Base-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ45
100Base-T(X)
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ45
UTP 100 m (328 ft)
RJ45
1000Base-T(X)
Cat
5e,6
PIN
Definition
1
BI_DC+
2
BI_DD+
3
BI_DD-
4
BI_DA-
5
BI_DB+
6
BI_DA+
7
BI_DC-
8
BI_DB-
4.2 Console Port Pin Definition
ORing Industrial Networking Corp.
13
TGAR-1062/2062/1662 Series User Manual
4.3 DI/DO
4.4 Wireless Antenna
The series uses 2.4GHz/5GHz antennas with reversed SMA connectors. You can also use
external RF cables and antennas with the connectors.
ORing Industrial Networking Corp.
14
TGAR-1062/2062/1662 Series User Manual
4.5 Cellular Antenna
The series are packed with one or two 3G and 4G antennas. External RF cables and antennas
can also be used with the connector.
3G Cellular Antenna
4G LTE Antenna
ORing Industrial Networking Corp.
15
TGAR-1062/2062/1662 Series User Manual
Management
5.1 Network Connection
Before installing the router, you need to be able to access the router via a computer equipped
with an Ethernet card or wireless LAN interface. To simplify the connection, it is
recommended to use an Ethernet card to connect to a LAN.
Network Connection of the Router
Before installing the router, you need a computer equipped with an Ethernet card or wireless
LAN interface. To simplify the connection, it is recommended to use an Ethernet card to
connect to a LAN. Follow the steps below to install and connect the router to PCs:
Step 1: Select a power source. The router can be powered by +12~48V DC power input.
Step 2: Connect a computer to the router. Use either a straight-through Ethernet cable or
cross-over cable to connect the ETH1 port of the router to a computer. Once the LED of the
LAN port lights up, which indicates the connection is established, the computer will initiate a
DHCP request to retrieve an IP address from the AP router.
Step 3: Configure the router on a web-based management utility. Open a web browser on
your computer and type http://192.168.10.1 (default gateway IP of the router) in the address
box to access the webpage. A login window will pop up where you can enter the default login
name admin and password admin. For security reasons, we strongly recommend you to
change the password. Click on System Tools > Login Setting after logging in to change the
password.
ORing Industrial Networking Corp.
16
TGAR-1062/2062/1662 Series User Manual
After you log in successfully, a Web interface will appear, as shown below. On the left hand
side of the interface is a list of functions where you can configure the settings. The details of
the configurations will be shown on the right screen.
5.2 Configuration
On top of the Home screen shows information about the firmware version, uptime, and WAN
IP address.
Label
Description
Firmware
Shows the current firmware version
Uptime
Shows the elapsed time since the AP router is started
Wan IP
Shows WAN IP address
5.2.1 Basic Setting
This section will guide you through the general settings for the router.
ORing Industrial Networking Corp.
17
TGAR-1062/2062/1662 Series User Manual
WAN
This page allows you to configure WAN settings. Different WAN connection types will have
different settings.
WAN Connection Type as Dynamic/Static IP:
Label
Description
Obtain an IP address
Select this option if you want the IP address of the WAN port to be
automatically
assigned automatically by the DHCP server in your network.
Use the following IP
Select this option if you want to assign an IP address to the WAN
address
port manually. You should set IP Address, Subnet Mask, and
Default Gateway according to IP rules.
Obtain DNS server
Obtains a DNS server address from a DHCP server. If you have
address
chosen to obtain an IP address automatically, this option will be
automatically
selected accordingly.
Use the following
Specifies a DNS server address manually. You can enter two
DNS server
addresses as the primary and secondary options.
addresses
Use Modem/3G as
Enable this option if you want to use Modem/3G as a backup
backup connection
connection when main connection is lost.
ORing Industrial Networking Corp.
18
TGAR-1062/2062/1662 Series User Manual
Enter your account username and password in the corresponding
fields.
Type a website address such as www.google.com in Ping Test
Site to use it to check if the connection is alive or lost.
WAN Connection Type as PPPoE:
Label
Description
User Name /
Enter the username & password provided by your ISP.
Password
Service Name
Enter the service name provided by your ISP
AC Name
Enter the name of the access concentrator provided by your ISP
Specify the IP & DNS
Enter a static IP and DNS address required by other ISPs
provided by ISP
Connection Mode
Auto: connect automatically when the router boots up
Connect on Demand: disconnect the PPP session if the router
ORing Industrial Networking Corp.
19
TGAR-1062/2062/1662 Series User Manual
has had no traffic for a specified amount of time. Fill a number in
the Max Idle Time field.
Manual: connects or disconnects manually via the
Connect/Disconnect buttons at the end of the page
Enable this option if you want to use modem/3G as a backup
connection when main connection is lost.
Use Modem/3G as
Enter your account username and password in the corresponding
backup connection
fields.
Type a website address such as www.google.com in Ping Test
Site to use it to check if the connection is alive or lost.
WAN Connection Type as Modem/3G/4G
Label
Description
APN
Enter the APN value (optional)
User Name
Enter the user name provided by your ISP
Password
Enter the password provided by your ISP
PIN
Enter a PIN code if you want to perform PIN check
Auto Connect
Check to start connections when the router boots up
Reconnect on Failure
Check to allow for reconnection when links fail
UIM Status
Shows the status of SIM card
ORing Industrial Networking Corp.
20
TGAR-1062/2062/1662 Series User Manual
Operations
Click Connect to start modem/3G connections or Disconnect to
shut down connections
Link Status
Shows the status of connections
Modem Status
Shows information about the modem
WAN Connection Type as Wireless Client
Label
Obtain an IP
address
automatically
Description
Select this option if you want the IP address of the WAN port to be
assigned automatically by the DHCP server in your network.
Use the following IP
Select this option if you want to assign an IP address to the WAN
address
port manually. You should set IP Address, Subnet Mask, and
Default Gateway according to IP rules.
Obtain DNS server
Obtains a DNS server address from a DHCP server. If you have
ORing Industrial Networking Corp.
21
TGAR-1062/2062/1662 Series User Manual
address
chosen to obtain an IP address automatically, this option will be
automatically
selected accordingly.
Use the following
Specifies a DNS server address manually. You can enter two
DNS server
addresses as the primary and secondary options.
addresses
Peer AP SSID
Enter the SSID of the AP you want to connect as a client
Site Survey
Click the button to browse available sites if you do not know the
SSID. A list of available sites will be displayed.
Security Type
Select the security type used by the client you want to connect
Use Modem/3G as
Enable this option if you want to use modem/3G as a backup
backup connection
connection when main connection is lost.
Enter your account username and password in the corresponding
fields.
Type a website address such as www.google.com in Ping Test Site
to use it to check if the connection is alive or lost.
LAN
This page allows you to configure the IP settings of the LAN for the router. The LAN IP
address is private to your internal network and is not visible to Internet.
Label
Description
Router Name
Enter the name of your router
IP Address
The IP address of the LAN. The default value is 192.168.10.1
Subnet Mask
The subnet mask of the LAN. The default value is 255.255.255.0
LLDP Protocol
LLDP is a vendor-neutral protocol used by network devices for
advertising their identity, capabilities, and neighbors on a LAN. You
can enable or disable LLDP protocol.
DHCP
DHCP is a network protocol designed to allow devices connected to a network to
communicate with each other using an IP address. The connection works in a
ORing Industrial Networking Corp.
22
TGAR-1062/2062/1662 Series User Manual
client-server model, in which DHCP clients request an IP address from a DHCP server.
The router comes with a built-in DHCP (Dynamic Host Control Protocol) server which assigns
an IP address to a computer (DHCP client) on the LAN automatically. The router can also
serve as a relay agent which will forward DHCP requests from DHCP clients to a DHCP
server on the Internet.
The IP allocation provides one-to-one mapping of MAC address to IP address. When a
computer with a MAC address requesting an IP address from the router, it will be assigned
with the IP address according to the mapping. You can choose one from the client list and
add it to the mapping list.
Label
Description
DHCP Mode
Available options include Built-in DHCP Server and DHCP
Forwarder. Built-in DHCP Server will enable the router to
automatically assign an IP address to a computer on the LAN.
ORing Industrial Networking Corp.
23
TGAR-1062/2062/1662 Series User Manual
DHCP Forwarder will forward DHCP messages to a server on
the Internet to handle DHCP requests. If you choose DHCP
Forwarder, enter a DHCP server IP address.
DHCP Server
Enables or disables the DHCP server function. The default
setting is Enabled.
Starting IP
The starting IP address of the IP range assigned by the DHCP
server
Ending IP
The ending IP address of the IP range assigned by the DHCP
server
Lease Time
The period of time for the IP address to be leased. During the
lease time, the DHCP server cannot assign that IP address to
any other clients. Enter a number in the field. The default setting
is 48 hours.
Local Domain Name
Enter the local domain name of a private network (optional)
DNS Server 1&2
Enter the IP address for the DNS server (optional)
WINS Server
Enter the WINS server (optional)
Starting IP
The starting IP for the DHCP relay range
Ending IP
The ending IP for the DHCP relay range
Subnet Mask
Enter a Subnet mask for the DHCP relay range
List of DHCP Range
for Relay
Shows all IP addresses for the DHCP relay range
Allocate IP Address
By selecting an IP address from the drop-down list and click
Manually
Copy to, you can edit the MAC addresses and IP addresses
already assigned by the router and add it to Static DHCP Client
List.
MAC Address
The MAC addresses of the computer.
IP Address
The IP address to be related to the MAC address.
Static
DHCP
List
Client
Shows the IP addresses locked to specific MAC addresses
Wireless AP
You can set the device to work in AP mode. This is the most common mode for all wireless
APs. In this mode, the AP will act as a central connection point which other wireless clients
can connect to.
ORing Industrial Networking Corp.
24
TGAR-1062/2062/1662 Series User Manual
Label
Description
SSID index
The index of the SSID
SSID (Service Set Identifier) is a unique name that identifies a
SSID
network. All devices on the network must be set with the same
SSID in order to communicate with each other. Fill in a new
SSID in this field if you do not want to use the default value.
Specify a channel to be used. Channel 6 is the default channel.
Channel
You can also select a new number from the dropdown list. All
devices on the network must be set to use the same channel to
communicate on the network.
A WDS master is the central control point for authenticating
wireless clients, caching client key material, distributing MFP
WDS-Master Mode
key material, reporting radio management information to an
upstream network management station, and updating other APs
participating in WDS. You can set the device as the
WDS-master by selecting from the list.
This function prevents devices connected to an AP from
AP Isolation
communicating directly with each other. This function is useful
when many wireless clients request your network frequently.
You can choose the security type for your WLAN connection
from the following options:
Security options
None: no encryption
WEP: WEP (Wired Equivalent Privacy) is a wireless security
protocol for WLAN. WEP will encrypt data transmitted on the
WLAN.
ORing Industrial Networking Corp.
25
TGAR-1062/2062/1662 Series User Manual
WPA/WPA2
Personal:
uses
a
pre-shared
key
for
authentication. This pre-shared key is then dynamically sent
between the AP and clients. Each authorized computer is given
the same pass phrase.
WPA/WPA2 Enterprise: this type includes all of the features of
WPA/WPA2
Personal
plus
support
for 802.1x RADIUS
authentication.
802.1x: authentication through a RADIUS server
When you set security type as WEP, the following fields will appear to allow you to configure
individual settings.
Label
Description
Available values include Open, Shared, and WEPAUTO. When
choosing Open or Shared, all of the clients must select the
Auth Mode
same authentication to associate this AP. If select WEPAUTO,
the clients do not have to use the same Open or Shared
authentication. They can choose any one to authenticate.
WEP Encryption
You can select 64 Bit or 128 Bit.
Available values include ASCII and Hex Key Type. ASCII
(American Standard Code for Information Interchange) is a
Key Type
code for representing English characters as numbers in the
range from 0 to 127. Hex digits uses 0–9 to represent values
zero to nine, and characters A-F to represent values ten to
fifteen.
Default Key Index
Select one of the keys to be the active key
Key 1 to 4
You can input up to four encryption keys.
ORing Industrial Networking Corp.
26
TGAR-1062/2062/1662 Series User Manual
When you set security type as WPA/WPA2-Personal, the following fields will appear to allow
you to configure individual settings.
Label
Description
Available
values
include
WPAPSK,
WPA2PSK,
and
WPAPSK/WPA2PSK mix. WPAPSK and WPA2PSK will
encrypt the link without additional RADIUS server, only an
Auth Mode
access point and client station that supports WPA-PSK is
required. For WPA/WPA2, authentication is achieved via WPA
RADIUS Server. You need a RADIUS or other authentication
server on the network.
Available values include TKIP, AES, and TKIP/AES mix.
Encryption Type
WPA-PSK uses TKIP encryption, and WPA2-PSK uses AES
encryption. TKIP/AES provides the most reliable security, and is
easiest to implement.
Shared Key
Enter a pass phrase in this field. The value must be within 8 to
64 characters
When you set security type as WPA /WPA2 Enterprise, the following screen will appear to
allow you to configure individual settings.
Label
Description
Available
Auth Mode
values
include
WPAPSK,
WPA2PSK,
and
WPAPSK/WPA2PSK mix. WPAPSK and WPA2PSK will
encrypt the link without additional RADIUS server, only an
access point and client station that supports WPA-PSK is
ORing Industrial Networking Corp.
27
TGAR-1062/2062/1662 Series User Manual
required. For WPA/WPA2, authentication is achieved via WPA
RADIUS Server. You need a RADIUS or other authentication
server on the network.
Available values include TKIP, AES, and TKIP/AES mix.
Encryption Type
WPA-PSK uses TKIP encryption, and WPA2-PSK uses AES
encryption. TKIP/AES provides the most reliable security, and is
easiest to implement.
Radius Server IP
Enter the IP address of the RADIUS server
Radius Port
Enter the RADIUS port (default is 1812)
Shared Secret
Enter the RADIUS password or key
When you set security type as 802.1x, the following fields will appear to allow you to configure
individual settings.
Label
Description
WEP Encryption
You can select 64 Bit or 128 Bit.
Available values include ASCII and Hex Key Type. ASCII
(American Standard Code for Information Interchange) is a code for
Key Type
representing English characters as numbers in the range from 0 to
127. Hex digits uses 0–9 to represent values zero to nine, and
characters A-F to represent values ten to fifteen.
Default Key Index
Select one of the keys to be the active key
Key 1 to 4
Input up to four encryption keys
Radius Server IP
Enter the IP address of the RADIUS server
Radius Port
Enter the RADIUS port (default is 1812)
Shared Secret
Enter the RADIUS password or key
RADIUS (Remote Authentication Dial-In User Service) is a widely deployed protocol that
ORing Industrial Networking Corp.
28
TGAR-1062/2062/1662 Series User Manual
enables companies to authenticate and authorize remote users’ access to a system or
service from a central network server.
When you configure the remote access server for RADIUS authentication, the credentials of
the connection request are passed to the RADIUS server for authentication and authorization.
If the request is both authenticated and authorized, the RADIUS server sends an accept
message back to the remote access server and the connection attempt is accepted. If the
request is either not authenticated or not authorized, the RADIUS server sends a reject
message back to the remote access server and the connection attempt is rejected.
The principle of the Radius server is shown in the following pictures:
Client Mode
In this mode, the router functions as a wireless client to connect your wired devices to a
wireless network. This mode provides no access point services but supports 802.1X.
ORing Industrial Networking Corp.
29
TGAR-1062/2062/1662 Series User Manual
Label
Description
Peer AP SSID
Enter the SSID of the AP you want to connect as a client
Peer AP BSSID
Enter the BSSID (Wireless MAC address) to limit client target
Site Survey
You can scan APs on the network using this mode.
Slave Mode
Enables or disables slave mode
Security Type
Select the security type used by the client you want to connect
DDNS
DDNS (Dynamic Domain Name System) allows you to configure a domain name for your IP
address which is dynamically assigned by your ISP. Therefore, you can use a static domain
name that always points to the current dynamic IP address.
Label
Description
DDNS Service
Choose a DDNS service provider from the list
User Name
Enter the user name of your DDNS account
Password
Enter the password of your DDNS account
Domain
Enter the domain name provided by your dynamic DNS service provider
Date & Time
In this page, you can set the date & time of the device. A correct date and time will help the
system log events. You can set up a NTP (Network Time Protocol) client to synchronize date
& time with a NTP server on the Internet.
ORing Industrial Networking Corp.
30
TGAR-1062/2062/1662 Series User Manual
Label
Description
NTP
Enables or disables NTP function
NTP Server 1
The primary NTP server
NTP Server 2
The secondary NTP server
Time Zone
Select the time zone you are located in
Synchronize
Specify the scheduled time for synchronization
Local Date
Set a local date manually
Local Time
Set a local time manually
Get Current Date &
Click to set the time from your browser
Time from Browser
5.2.2 Networking Setting
This section will guide you through various networking settings, including wireless, NAT,
firewall, VPN, VRRP, and routing protocol.
Wireless Setting – Advanced Setting
This page allows you to set up wireless configuration.
Label
Description
Radio Button
Enables or disables wireless function
Beacon Interval
A beacon is a packet sent by a wireless access point to
synchronize wireless devices. The beacon interval value indicates
ORing Industrial Networking Corp.
31
TGAR-1062/2062/1662 Series User Manual
the frequency interval of the beacon. Increasing the beacon
interval reduces the number of beacons and the overhead
associated with them. The default value is 100, but 50 is
recommended when reception is poor.
DTIM Interval
A DTIM interval determines how often a beacon frame includes
a Delivery Traffic Indication message, a message that informs
the clients about the presence of buffered multicast/broadcast
data on the access point. The message is generated within the
periodic beacon at a frequency specified by the DTIM Interval.
When the AP sends a DTIM with a DTIM interval value, the client
hearing the beacons will awake to receive the messages. The
default value is 1, and the value must be between 1 and 255
milliseconds.
Fragmentation
The value specifies the maximum size for a packet before data is
Threshold
fragmented into multiple packets. The value should remain at the
default 2346 (the range is 256 - 2346 bytes). If you experience a
high packet error rate, you may slightly increase the value. Setting
the value too low may result in poor network performance. Only
minor modifications of this value are recommended.
RTS Threshold
The RTS (Request to Send) Threshold is the amount of time a
wireless device, attempting to send, will wait for a recipient to
acknowledge that it is ready. Normally, the AP sends a RTS frame
to a station and negotiates the sending of data. After receiving the
RTS, the station responds with a CTS (Clear to Send) frame to
acknowledge the right to begin transmission. To ensure
communication, the maximum value should be used, which is the
default value 2347 (the range is 0-2347 bytes). If a network
packet is smaller than the preset RTS threshold size, the
RTS/CTS mechanism will not be enabled.
Wireless Mode
You can select 802.11 b, b/g, or b/g/n mode.
Preamble
Available values include Long and Short, with Long as the
default value. If all clients and access points in your wireless
network support short preamble, then enabling it can boost
overall throughput. However, if any wireless device does not
support short preamble, then it will not be able to communicate
with your network. If you are not sure whether your radio supports
the short RF preamble, you must disable this feature.
ORing Industrial Networking Corp.
32
TGAR-1062/2062/1662 Series User Manual
Label
Description
Roaming
Select Disabled to disable X-Roaming protocol or select
X-roaming to enable X-Roaming protocol
Scan Channel
Select All to scan all supported channels or Manual to scan only
selected channels specified in Channel Select.
Channel Select
Assign the value roaming channels
Sensitivity
Configures signal sensitivity
Scan Interval
Configures scan interval
Wireless Setting – MAC Filter
This page allows you to set up MAC filters to allow or deny wireless clients to connect to the
router. You can manually add a MAC address or select a MAC address from the Associated
Clients list currently associated with the router.
ORing Industrial Networking Corp.
33
TGAR-1062/2062/1662 Series User Manual
Label
Description
MAC Filter
Select Enabled or Disabled to activate or deactivate MAC filters
Options
Select one of the options to allow or deny the MAC address in
the list
Associated Clients
Shows the wireless MAC addresses associated with the router
MAC Filter Table
You can edit up to MAC addresses in these fields
Apply
Click to activate the configurations
NAT Setting - Virtual Server
This page allows you to set up virtual server setting. A virtual server allows Internet users to
access services on your LAN. This is a useful function if you host services online such as FTP,
Web or game servers. A public port must be defined for the virtual server on your router in
order to redirect traffic to an internal LAN IP address and LAN port. Any PC used as a virtual
server must have a static or reserved IP address.
Label
Description
Virtual Server
Select Enabled or Disabled to activate or deactivate virtual
server
Description
Enter the description of the entry. Acceptable characters are 0-9,
a-z, and A-Z. A null value is allowed.
Public IP
Enter a public IP allowed to access the virtual service. If not
specified, choose All.
Public Port
The port number to be used to access the virtual service on the
ORing Industrial Networking Corp.
34
TGAR-1062/2062/1662 Series User Manual
WAN (Wide Area Network)
Protocol
The protocol used for the virtual service
Local IP
The IP address of the computer that will provide virtual service
Local Port
The port number of the service used by the private IP computer
Enable Now
Enables the virtual server entry after adding it
Virtual server list
Click Edit to edit the virtual service entry and Del to delete the
entry.
NAT Setting – DMZ
DMZ (Demilitarized Zone) allows a computer to be exposed to the Internet without passing
through the security settings and therefore is unsecured. This feature is useful for special
purposes such as gaming.
To use this function, you need to set an internal computer as the DMZ host by entering its IP
address. Adding a client to the DMZ may expose your local network to a variety of security
risks, so use this function carefully.
Label
Description
DMZ
Enables or disables DMZ
Description
Enter a description for the DMZ host entry
DMZ Host IP
Enter the IP address of the computer to act as the DMZ host
NAT Setting – UPnP
The UPnP (Universal Plug and Play) feature allows Internet devices to access local host
resources or devices as needed. UPnP-enabled devices can be automatically discovered by
the UPnP service application on the LAN.
ORing Industrial Networking Corp.
35
TGAR-1062/2062/1662 Series User Manual
Label
Description
UPnP
Enable or disable UPnP.
Enable NAT-PMP
NAT-PMP allows a computer in a private network (behind a NAT
router) to automatically configure the router to allow parties
outside the private network to contact with each other. NAT-PMP
operates with UDP. It essentially automates the process of port
forwarding. Check the box to enable NAT-PMP.
UPnP List
This table lists the current auto port forwarding information.
Application: The application that generates this port forwarding.
Ext Port: The port opened on WAN
Protocol: The protocol type
Int Port: The port redirected to the local computer
IP Address: The IP address of local computer to be redirected to
Firewall Setting – IP Filter
IP filters enable you to control the forwarding of incoming and outgoing data between your
LAN and the Internet and within your LAN. This control is implemented via IP filter rules which
are defined to block attempts by certain computers on your LAN to access certain types of
data or Internet locations. You can also block incoming access to computers on your LAN.
ORing Industrial Networking Corp.
36
TGAR-1062/2062/1662 Series User Manual
Label
Description
IP Filter
Enables or disables the IP Filter
Description
Enter description for the entry.
Rule
Configures the rules to be applied to the IP filter. Available options
include DROP, ACCEPT, and REJECT.
Direction
Specifies the direction of data flow to be filtered
IP Address
Enter the IP address of the source and destination computer
Protocol
Configures the protocol to be filtered
Enable Now
Click Yes to enable the entry after adding it
IP filter list
Shows the information of all IP filters. Click Edit to edit the entry
or Del to delete the entry.
Firewall Setting – MAC Filter
This page enables you to deny or allow LAN computers to access the Internet based on their
MAC addresses.
Label
Description
MAC Filter
Enables or disables the MAC Filter
Description
Enter description for the entry
Rule
Configures the rules to be applied to the MAC filter. Available
options include DROP, ACCEPT, and REJECT.
MAC Address
Enter the MAC address to be filtered
Enable Now
Click Yes to enable the entry after adding it
IP filter list
Shows the information of all MAC filters. Click Edit to edit the
entry or Del to delete the entry.
ORing Industrial Networking Corp.
37
TGAR-1062/2062/1662 Series User Manual
Vpn Setting – Open Vpn
A VPN is a method of linking two locations as if they are on a local private network to facilitate
data transmission and ensure data security. The links between the locations are known as
tunnels. VPN can achieve confidentiality, authentication, and integrity of data by utilizing
encapsulation protocols, encryption algorithms, and hashing algorithms.
Open VPN enables you to easily set up a virtual private network over an encrypted
connection. It is a full-function SSL VPN solution which accommodates a wide range of
configurations including remote access, site-to-site VPNs, WiFi security, and enterprise-level
remote access with load balancing, failover, and fine-grained access control features.
To set up your router as an Open VPN server, you need to install openvpn client software for
your
Windows-based
PC.
You
can
download
it
from
http://openvpn.net/download.html#stablel. The software version must match the current
version of Openvpn used by IGAR-2062+-3G/4G which is version 2.0.9.
Connection to Open VPN Server
When you enable Open VPN Client, you need two routers to create site-to-site VPN
connections. The server IP and client IP address should be within the same network domain.
ORing Industrial Networking Corp.
38
TGAR-1062/2062/1662 Series User Manual
Open VPN Server and Client Connection
ORing Industrial Networking Corp.
39
TGAR-1062/2062/1662 Series User Manual
Label
Description
Open VPN Server
Enables or disables the function of Open VPN server
Tunnel Protocol
Select UDP or TCP protocol depending on your needs. TCP is more
reliable than UDP, but UDP performs better than TCP. It is
recommended to use UDP if the distance between VPN server and
client is short; otherwise, use TCP.
Port
The number of the port (default is 1194).
LZO Compression
Enables or disables the function of LZO Compression
Keys Setting
Select Auto to use preset certificates or Manual to use your
certificates. Please install openvpn client software to generate your
certificates and paste them here. For more information, please visit
openvpn website.
Open VPN Client
Enables or disables the function of Open VPN client.
Server IP
Enter the Open VPN server IP address
Tunnel Protocol
Select UDP or TCP protocol depending on your needs. TCP is more
reliable than UDP, but UDP performs better than TCP. It is
recommended to use UDP if the distance between VPN server and
client is short; otherwise, use TCP.
Port
The number of the port (default is 1194).
LZO Compression
Enables or disables the LZO Compression
Keys Setting
Select Auto to use preset certificates or Manual to use your
certificates. Please install openvpn client software to generate your
certificates and paste them here. For more information, please visit
openvpn website.
Vpn Setting – PPTP VPN
PPTP (Point to Point Tunneling Protocol) VPN allows PCs connected to the router through
WAN ports to act as PCs in the same LAN.
ORing Industrial Networking Corp.
40
TGAR-1062/2062/1662 Series User Manual
To create a PPTP connection to the router, you must create a new network connection on
your Windows PC by right clicking Network > Property > Create a new connection >
Connect to my work space (VPN) > Use VPN to Internet, and then enter the user name
and password set in the page.
After setting up a new connection, you can make configurations in the following page.
Label
Description
PPTP Server
Enables or disables PPTP VPN server
Server IP
Enter the server IP address. The default value is the IP address
of the connected LAN port.
ORing Industrial Networking Corp.
41
TGAR-1062/2062/1662 Series User Manual
Client IP
Enter the IP address range in the form of 192.168.10.xx-xx. The
connected client will be assigned with an IP address.
CHAP-Secrets
Enter the username and password pairs in the form of user *
pass *. Multiple username and password pairs are allowed.
Vpn Setting – PPTP Client
If a router wants to link to the routers in different networks, you should enable PPTP client in
the following page.
ORing Industrial Networking Corp.
42
TGAR-1062/2062/1662 Series User Manual
Label
Description
PPTP Client
Enables or disables PPTP client
Server IP/Hostname
Enter the server IP address or hostname
Username/Password
Enter the username and password assigned by PPTP server
Choose the rules to be applied
Reconnect on failure: prompts automatic reconnection when the link
fails.
Require-chap: check to use chap authentication on your PPTP
server
Options
Require-mschap: check to use mschap authentication on your PPTP
server
Require-mschap-v2: check to use mschap-v2 authentication on your
PPTP server
Require MPPE: check to use MPPE (Microsoft Point-to-Point
Encryption) encryption on data transmitted through PPP
(Point-to-Point Protocol) and VPN links.
Operations
Link Status
Click Connect to link to the server or Disconnect to disconnect from
the server
Show the status of the link
VRRP
A VRRP (Virtual Router Redundancy Protocol) is a computer networking protocol aimed to
eliminate the single point of failure by automatically assigning available IP routers to
participating hosts. Using a virtual router ID (VRID) address and virtual router IP (VRIP)
address to represent itself, a virtual router consists of two or more physical routers, including
one master router and one or more backup routers. All routers in the virtual router group
share the same VRID and VRIP. The master router provides primary routing and the backup
routers monitor the status of the master router and become active if the master router fails.
ORing Industrial Networking Corp.
43
TGAR-1062/2062/1662 Series User Manual
Label
Description
VRRP Protocol
Enables or disables VRRP function
VRRP Instance State
Specifies the router to act as the master or backup router
Virtual Router ID
A VRID consists of one master router and one or more backup
routers. The master router is the router that owns the IP
address you associate with the VRID. Configure the VRID on
the router that owns the default gateway interface. The other
router in the VRID does not own the IP address associated
with VRID but provides the backup path if the Master router
becomes unavailable.
Virtual Router IP
An IP address associated with the VRID from which other
hosts can obtain network service. The VRIP is managed by the
VRRP instances belonging to a VRID.
ORing Industrial Networking Corp.
44
TGAR-1062/2062/1662 Series User Manual
Priority
The priority value used by the VRRP router when selecting the
master virtual router.
Authentication Password
Enter the password for authentication
Routing Protocol – Routing Setting
This page shows the information of the routing table. You can configure static and dynamic
routing settings in this page.
Static Routing
When RIPv1 & v2 is Disabled, the router will operate in static routing mode, which means
routers forward packets using either route information from route table entries that you
manually configure or the route information that is calculated using dynamic routing
algorithms.
ORing Industrial Networking Corp.
45
TGAR-1062/2062/1662 Series User Manual
Dynamic Routing
Dynamic routing lets routing tables in routers change as the routes change. If the best path to
a destination cannot be used, dynamic routing protocols change routing tables when
necessary to keep your network traffic moving. Dynamic routing protocols include RIP, OSPF,
and BGP; however, the IGAR-2062 only supports RIP (Routing Information Protocol).
Do not choose Disable in the RIPv1 & v2 list if you want to enable Dynamic Routing. After
clicking Apply, more information will be displayed in Current Routing Table.
ORing Industrial Networking Corp.
46
TGAR-1062/2062/1662 Series User Manual
Label
Description
Current Routing
Shows all routing information, including static and dynamic routing
Table
(if enabled)
Static Route Entry
Fills in corresponding information to add new entries to the static
routing tablet
Mode
Choose Gateway Mode if you want PCs in the LAN to visit external
network, otherwise choose Router Mode
RIPv1 &v2
Choose Disable to disable dynamic routing or other options to
configure the interfaces for dynamic routing
Telnet Setting
This option is only available when dynamic routing is enabled. It
allows you to make detailed configurations via simple comments.
Routing Topography
ORing Industrial Networking Corp.
47
TGAR-1062/2062/1662 Series User Manual
5.2.3 System Tools
Login Setting
You can change login name and password in page. The default login name and password are
both admin.
Label
Description
Old Name
Type in current login name
Old Password
Type in current password
New Name
Enter a new login name. Acceptable characters contain '0-9',
'a-z', 'A-Z' and the length must be 1 to 15 characters. An empty
name is not acceptable.
New Password
Enter a new login password. Acceptable characters contain
'0-9', 'a-z', 'A-Z' and the length must be 0 to 15 characters.
Confirm New Password
Retype the new password to confirm it.
Web Protocol
Choose a web management page protocol from HTTP and
HTTPS. HTTPS (HTTP over SSL) encrypts data sent and
received over the Web. Choose HTTPS if you want a secure
connection.
Port
Choose a web management page port number. For HTTP,
default port is 80. For HTTPS, default port is 443.
Router Restart
This page allows you to configure restart settings for the router.
ORing Industrial Networking Corp.
48
TGAR-1062/2062/1662 Series User Manual
Label
Description
Restart Now
Click to restart the router via warm reset
Scheduling
Enable: check to activate the setting
Restart at: specify the time for resetting the router. You can configure the
action to be performed periodically.
Firmware Upgrade
ORing launches new firmware constantly to enhance router performance and functions. To
upgrade firmware, download new firmware from ORing’s website to your PC and install it via
Web upgrade. Make sure the firmware file matches the model of your router. It will take
several minutes to upload and update the firmware. After upgrade completes successfully,
reboot the router.
During firmware upgrading, do not turn off the power of the router or press the
reset button.
Save/Restore Configurations
This page allows you to save configurations or return settings to previous status. You can
download the configuration file from the Web. Note: users using old versions of Internet
Explorer may have to click on the warning on top of the browser and choose Download File.
ORing Industrial Networking Corp.
49
TGAR-1062/2062/1662 Series User Manual
Label
Description
Save
Click to save existing configurations as a file for future usage.
Select File
You can restore configurations to previous status by installing a
previous configuration file. To do this, choose Web Restore or
Tftp Restore. If you choose Web Restore, you need to choose a
file and click Web Restore. If you selet Tftp Restore, fill in a Tftp
server IP address and the file name before clicking Tftp Restore.
Restore Factory
Click to reset the router to the factory settings. The router will
Default Setting
reboot to validate the default settings.
Miscellaneous
This page enables you to run ping test which will send out ping packets to test if a computer is
on the Internet or if the WAN connection is OK. Enter a domain name or IP address in the
destination box and click Ping to test.
Event Warning
When an error occurs, the router will notify you through system log, e-mail, SNMP, and relay.
ORing Industrial Networking Corp.
50
TGAR-1062/2062/1662 Series User Manual
System Log
Label
Description
Syslog Server IP
Enter the IP address of a remote server if you want the logs to be
stored remotely. Leave it blank will disable remote syslog.
Syslog Server Port
Specifies the port to be logged remotely. Default port is 514.
ORing Industrial Networking Corp.
51
TGAR-1062/2062/1662 Series User Manual
E-mail
Label
Description
SMTP Server
Enter a backup host to be used when the primary host is
unavailable.
Server Port
Specifies the port where MTA can be contacted via SMTP server
E-mail Address 1-4
Enter the mail address that will receive notifications
ORing Industrial Networking Corp.
52
TGAR-1062/2062/1662 Series User Manual
SNMP
ORing Industrial Networking Corp.
53
TGAR-1062/2062/1662 Series User Manual
Label
Description
SNMP Agent
SNMP (Simple Network Management Protocol) Agent is a service
program that runs on the access point. The agent provides management
information to the NMS by keeping track of various operational aspects
of the AP system. You can enable or disable the function.
SNMP Trap
Enter the IP address of the SNMP server which will send out traps
Server 1-4
generated by the AP.
Community
Community is a password to establish trust between managers and
agents. Normally, public is used for read-write community.
SysLocation
Specifies sysLocation string
SysContact
Specifies sysContact string
Relay
DIDO
ORing Industrial Networking Corp.
54
TGAR-1062/2062/1662 Series User Manual
5.2.4 System Status
System Info
This page displays the detailed information of the router including model name, description,
firmware version, WAN, LAN and wireless settings.
System Log
The router will constantly log events and activities and provide the files for you to review. You
can click Refresh to renew the page or Clear Logs to clear all or certain log entries.
Traffic Statistics
This page displays network traffic statistics for packets both received and transmitted through
Ethernet ports and wireless connections.
ORing Industrial Networking Corp.
55
TGAR-1062/2062/1662 Series User Manual
Wireless Link List
This page displays the Mac address of all wireless clients connected.
ORing Industrial Networking Corp.
56
TGAR-1062/2062/1662 Series User Manual
Technical Specifications
ORing WLAN Access
Point Model
TGAR-1062-M12-3G
TGAR-1062-M12-4G
TGAR-2062-M12-3G
TGAR-2062-M12-3G
Physical Ports
10/100/1000Base-T(X) Ports in
M12
Auto
MDI/MDIX
2
(8-pin
A-coding)
DIDO
port
in
M12
(5-pin
2 (DI x 4 and DO x 4)
A-coding)
RS-232 Console port in M12
115200, 8 ,N ,1
(5-pin A-coding)
Relay
port
in
M12
(5-pin
1A@24VDC
A-coding)
SIM Card Slot
1
1
2
2
WLAN interface
Antenna Connector
Radio Frequency Type
2 x reverse SMA-type antenna connector
DSSS, OFDM
IEEE802.11a : OFDM with BPSK, QPSK, QAM, 64QAM
Modulation
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11n : BPSK, QPSK, 16-QAM, 64-QAM
America / FCC :
Frequency Band
2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz ( 9 channels )
Europe CE / ETSI : 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz (4 channels)
IEEE802.11b: 1 / 2 / 5.5 / 11 Mbps
Transmission Rate
IEEE802.11a/g: 6 / 9 / 12 / 18 / 24 / 36 / 48 / 54 Mbps
IEEE801.11n: up to 300Mbps
802.11a: 12dBm ± 1.5dBm
802.11b: 18dBm ± 1.5dBm
802.11g: 15dBm ± 1.5dBm
Transmit Power
802.11gn HT20: 13dBm ± 1.5dBm@150Mbps
802.11gn HT40: 12dBm ± 1.5dBm@300Mbps
802.11an HT20: 12dBm ± 1.5dBm@150Mbps
802.11an HT40: 12dBm ± 1.5dBm@300Mbps
802.11a: -68dBm ± 2dBm@54Mbps
802.11b: -85dBm ± 2dBm@11Mbps
802.11g: -68dBm ± 2dBm@54Mbps
Receiver Sensitivity
802.11gn HT20: -68dBm ± 2dBm@150Mbps
802.11gn HT40: -68dBm ± 2dBm@300Mbps
802.11an HT20: -68dBm ± 2dBm@150Mbps
802.11an HT40: -68dBm ± 2dBm@300Mbps
WEP: (64-bit ,128-bit key supported)
WPA/WPA2 :802.11i(WEP and AES encryption)
Encryption Security
WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security
SSID broadcast disable
Cellular Interface
Cellular Standard
Antenna Connector
GSM / GPRS/ EGPRS/
GSM / GPRS/ EGPRS/
GSM / GPRS/ EGPRS/
GSM / GPRS/ EGPRS/ EDGE /
EDGE
EDGE / WCDMA / HSDPA
EDGE / WCDMA / HSDPA
WCDMA / HSDPA / HSUPA
HSDPA / HSUPA
/ HSUPA /HSPA+ /LTE
/ HSUPA
/HSPA+ /LTE
1 x RP-SMA Female
1 x SMA Female
2 x RP-SMA Female
2 x SMA Female
/
WCDMA
ORing Industrial Networking Corp.
/
57
TGAR-1062/2062/1662 Series User Manual
America(US)
LTE:
700/1700/2100/
America(US)
MHz
LTE:
UMTS/HSDPA/HSUPA/H
700/1700/2100/ MHz
SPA+/DC-HSPA+:
Dual-band :
HSUPA
+/DC-HSPA+:
800/850/1900/2100
Dual-band :
MHz
1900/2100 MHz
GSM/GPRS/EDGE:
MHz
Quad-band :
GSM/GPRS/EDGE:
HSUPA
GSM/GPRS/EDGE
1900/2100 MHz
Band Option
UMTS/HSDPA/HSUPA/HSPA
800/850/1900/2100
850/900/1800/1900
Quad-band :
850/900/1800/1900
850/900/1800/1900
GSM/GPRS/EDGE
MHz
MHz
MHz
Europe(EU)
Europe(EU)
850/900/1800/1900 MHz
LTE:
LTE:
WCDMA/HSDPA
WCDMA/HSDPA
850/900/1900/2100
800/900/1800/2100/2600
850/900/1900/2100 MHz
800/900/1800/2100/2
600 MHz
MHz
MHz
UMTS/HSDPA/HSUPA/HSPA
UMTS/HSDPA/HSUPA/H
+/DC-HSPA+:
SPA+/DC-HSPA+:
900/2100 MHz
900/2100 MHz
GSM/GPRS/EDGE:
GSM/GPRS/EDGE:
900/1800/1900 MHz
900/1800/1900
MHz
Protocol Support
Protocol
ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, PPPoE, STP (IEEE 802.1D)
LED indicators
Power Indicator
10/100/1000Base-T(X)
Indicator
2 x LEDs, Green for Power on
2 x LEDs, Green for port Link/Act
WLAN LED
1 x LED, Green for WLAN Link/Act
WAN LED
1 x LED, Green for Cellular modem Link/ Act
Fault Indicator
1 x LED, Red for Ethernet link down or power down indicator
2 x LEDs, Green for functioning normal
Fault contact
Relay
Relay output to carry capacity of 3A at 24VDC
Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power
Dual Power Inputs. 12~48 VDC on M23 connector (24 VDC Typ.)
Power Consumption (Typ.)
9 Watts
Overload Current Protection
Present
Reverse Polarity Protection
Present
9.5 Watts
13 Watts
15 Watts
Physical Characteristic
Enclosure
IP-40
Dimension (W x D x H)
125.6(W) x 65(D) x 196.1(H) mm (4.94 x 2.55 x 7.72 inch.)
Weight (g)
985g
968g
1030g
1030g
Environmental
Storage Temperature
-40 to 85oC (-40 to 185oF)
Operating Temperature
-25 to 70oC (-13 to 158oF)
Operating Humidity
5% to 95% Non-condensing
Regulatory approvals
EMI
EMS
FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2)
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),
EN61000-4-8, EN61000-4-11
ORing Industrial Networking Corp.
58
TGAR-1062/2062/1662 Series User Manual
Shock
IEC60068-2-27, EN61373
Free Fall
IEC60068-2-32
Vibration
IEC60068-2-6, EN61373
Rail Traffic
EN50155
Cooling
EN60068-2-1
Dry Heat
EN60068-2-2
Safety
EN60950-1
Warranty
5 years
ORing WLAN Access Point
Model
TGAR-1662-M12-3G
TGAR-1662-M12-4G
Physical Ports
10/100/1000Base-T(X) Ports in M12
2
Auto MDI/MDIX (8-pin A-coding)
DIDO port in M12 (5-pin A-coding)
2 (DI x 4 and DO x 4)
RS-232 Console port in M12
115200, 8 ,N ,1
(5-pin A-coding)
Relay port in M12 (5-pin A-coding)
1A@24VDC
SIM Card Slot
1
WLAN interface
Antenna Connector
Radio Frequency Type
4 x reverse SMA-type antenna connector
DSSS, OFDM
IEEE802.11a : OFDM with BPSK, QPSK, QAM, 64QAM
Modulation
IEEE802.11b: CCK, DQPSK, DBPSK
IEEE802.11g: OFDM with BPSK, QPSK, 16QAM, 64QAM
IEEE802.11n : BPSK, QPSK, 16-QAM, 64-QAM
America / FCC :
Frequency Band
2.412~2.462 GHz (11 channels)
5.180~5.240 GHz & 5.745~5.825 GHz ( 9 channels )
Europe CE / ETSI : 2.412~2.472 Ghz (13 channels)
5.180~5.240 GHz (4 channels)
IEEE802.11b: 1 / 2 / 5.5 / 11 Mbps
Transmission Rate
IEEE802.11a/g: 6 / 9 / 12 / 18 / 24 / 36 / 48 / 54 Mbps
IEEE801.11n: up to 300Mbps
802.11a: 12dBm ± 1.5dBm
802.11b: 18dBm ± 1.5dBm
802.11g: 15dBm ± 1.5dBm
Transmit Power
802.11gn HT20: 13dBm ± 1.5dBm@150Mbps
802.11gn HT40: 12dBm ± 1.5dBm@300Mbps
802.11an HT20: 12dBm ± 1.5dBm@150Mbps
802.11an HT40: 12dBm ± 1.5dBm@300Mbps
802.11a: -68dBm ± 2dBm@54Mbps
802.11b: -85dBm ± 2dBm@11Mbps
802.11g: -68dBm ± 2dBm@54Mbps
Receiver Sensitivity
802.11gn HT20: -68dBm ± 2dBm@150Mbps
802.11gn HT40: -68dBm ± 2dBm@300Mbps
802.11an HT20: -68dBm ± 2dBm@150Mbps
802.11an HT40: -68dBm ± 2dBm@300Mbps
WEP: (64-bit ,128-bit key supported)
WPA/WPA2 :802.11i(WEP and AES encryption)
Encryption Security
WPAPSK (256-bit key pre-shared key supported)
802.1X Authentication supported
TKIP encryption
Wireless Security
SSID broadcast disable
ORing Industrial Networking Corp.
59
TGAR-1062/2062/1662 Series User Manual
Cellular Interface
Cellular Standard
Antenna Connector
GSM / GPRS/ EGPRS/ EDGE / WCDMA /
GSM / GPRS/ EGPRS/ EDGE / WCDMA / HSDPA / HSUPA /HSPA+
HSDPA / HSUPA
/LTE
1 x Reverse SMA Female
1 x SMA Female
America(US)
LTE:
700/1700/2100/ MHz
UMTS/HSDPA/HSUPA/HSPA+/DC-HSPA+:
Dual-band : HSUPA 1900/2100 MHz
Quad-band :
Band Option
GSM/GPRS/EDGE
850/900/1800/1900
MHz
800/850/1900/2100 MHz
GSM/GPRS/EDGE:
850/900/1800/1900 MHz
Europe(EU)
LTE:
800/900/1800/2100/2600 MHz
WCDMA/HSDPA 850/900/1900/2100 MHz
UMTS/HSDPA/HSUPA/HSPA+/DC-HSPA+:
900/2100 MHz
GSM/GPRS/EDGE:
900/1800/1900 MHz
Protocol Support
Protocol
ARP,BOOTP, DHCP, DNS, HTTP, IP, ICMP, SNTP, TCP, UDP, RADIUS, SNMP, PPPoE, STP (IEEE 802.1D)
LED indicators
Power Indicator
2 x LEDs, Green for Power on
10/100/1000Base-T(X) Indicator
2 x LEDs, Green for port Link/Act
WLAN LED
2 x LED, Green for WLAN Link/Act
WAN LED
1 x LED, Green for Cellular modem Link/ Act
Fault Indicator
1 x LED, Red for Ethernet link down or power down indicator
Fault contact
Relay
Relay output to carry capacity of 1A at 24VDC
Power
Redundant Input Power
Dual Power Inputs. 12~48 VDC on M23 connector (24 VDC Typ.)
Power Consumption (Typ.)
13 Watts
Overload Current Protection
Present
Reverse Polarity Protection
Present
14 Watts
Physical Characteristic
Enclosure
IP-40
Dimension (W x D x H)
125.6(W) x 65(D) x 196.1(H) mm (4.94 x 2.55 x 7.72 inch.)
Weight (g)
1030g
Environmental
Storage Temperature
-40 to 85oC (-40 to 185oF)
Operating Temperature
-25 to 70oC (-13 to 158oF)
Operating Humidity
5% to 95% Non-condensing
Regulatory approvals
EMI
FCC Part 15, CISPR (EN55022) class A, EN50155 (EN50121-3-2)
EN61000-4-2 (ESD), EN61000-4-3 (RS), EN61000-4-4 (EFT), EN61000-4-5 (Surge), EN61000-4-6 (CS),
EMS
EN61000-4-8, EN61000-4-11
Shock
IEC60068-2-27, EN61373
Free Fall
IEC60068-2-32
Vibration
IEC60068-2-6, EN61373
Rail Traffic
EN50155
Cooling
EN60068-2-1
ORing Industrial Networking Corp.
60
TGAR-1062/2062/1662 Series User Manual
Dry Heat
EN60068-2-2
Safety
EN60950-1
Warranty
5 years
ORing Industrial Networking Corp.
61
TGAR-1062/2062/1662 Series User Manual
Compliance
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference and (2) this device must accept any
interference received, including interference that may cause undesired operation.
RF exposure warning: The equipment complies with RF exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
You are cautioned that changes or modifications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment. This device
should be operated with minimum distance 20cm between the device and all persons.
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Industry Canada - Class B This digital apparatus does not exceed the Class B limits for radio
noise emissions from digital apparatus as set out in the interference-causing equipment
standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.
Cet appareil numérique respecte les limites de bruits radioélectriques applicables aux
appareils numériques de Classe B prescrites dans la norme sur le matérial brouilleur:
“Appareils Numériques,” NMB-003 édictée par l’Industrie.
ORing Industrial Networking Corp.
62
TGAR-1062/2062/1662 Series User Manual
Operation is subject to the following two conditions: (1) this device may not cause interference,
and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer
d'interférences,et (2) cet appareil doit accepter toute interférence, y compris celles
susceptibles de provoquer fonctionnement du dispositif.
To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
permitted for successful communication.
Afin de réduire les interférences radio potentielles pour les autres utilisateurs, le type
d'antenne et son gain doivent être choisie que la puissance isotrope rayonnée équivalente
(PIRE) est pas plus que celle premise pour une communication réussie
RF exposure warning: The equipment complies with RF exposure limits set forth for an
uncontrolled environment. The antenna(s) used for this transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter.
Avertissement d'exposition RF: L'équipement est conforme aux limites d'exposition aux RF
établies pour un incontrôlés environnement. L'antenne (s) utilisée pour ce transmetteur ne
doit pas être co-localisés ou fonctionner en conjonction avec toute autre antenne ou
transmetteur.
ORing Industrial Networking Corp.
63