With Mobile Monitoring Capabilities

Owner’s Manual & Safety Instructions
Save This Manual Keep this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the
back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
18b
With Mobile Monitoring Capabilities
Visit our website at: http://www.harborfreight.com
Email our technical support at: productsupport@harborfreight.com
When unpacking, make sure that the product is intact
and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2017 by Harbor Freight Tools®. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in
any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing
improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
SAFETy
Safety ......................................................... 2
Manual Recording ..................................... 14
Specifications ........................................... 5
Video Motion Detection ............................. 14
Set up - Before Use: ................................. 6
Using Intercom .......................................... 15
Receiver Components and Controls........... 6
Camera Components and Controls ............ 8
Playback and Delete.................................. 16
Remote Viewing via MyCam View™ app .. 17
Viewing Modes .......................................... 10
Maintenance Instructions ....................... 18
Operating Instructions ............................ 12
Troubleshooting ...................................... 18
Receiver Functions .................................... 12
FCC Notice ............................................... 19
Display Functions ...................................... 13
Limited 90 Day warranty ......................... 20
wARNINg SyMBOLS AND DEFINITIONS
SETTINgS
This is the safety alert symbol. It is used to alert you to potential
personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.
OpERATION
Symbology
Double Insulated
V
Volts
~
A
Alternating Current
Amperes
IMpORTANT SAFETy INFORMATION
NETwORk
Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Page 2
For technical questions, please call 1-888-866-5797.
Item 63842
Installation precautions
2. Install only according to these instructions.
Improper installation can create hazards.
3. Do not overreach when installing this product.
keep proper footing and balance at all times.
This enables better control in unexpected situations.
4. Wear ANSI-approved safety goggles
during installation.
5. Keep installation area clean and well lit.
SAFETy
1. Check federal, state and local
surveillance laws before installing video
and/or audio surveillance equipment.
6. Keep children and bystanders out of
the area during installation.
7. Do not install when tired or when under the
influence of alcohol, drugs or medication.
Use precautions
2. Use as intended only.
4. Maintain product labels and nameplates.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
3. Do not modify.
Electrical Safety
1. power Adapter plug must match
the outlet. Never modify the plug in
any way. Unmodified plugs and matching
outlets will reduce risk of electric shock.
2. Do not expose Receiver to rain or wet
conditions. Water entering the Receiver
will increase the risk of electric shock.
3. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the Receiver.
keep cord away from heat, oil, sharp edges
or moving parts. Damaged or entangled
cords increase the risk of electric shock.
SETTINgS
1. This product is not a toy. Do not allow
children to play with or near this item.
Have your Surveillance equipment serviced by a qualified repair person
using only identical replacement parts.
This will ensure that the safety of the equipment is maintained.
Camera Safety warnings
1. To prevent electric shock, do not attempt
to disassemble Cameras. There are
no serviceable parts inside.
2. Use supplied Power Adapters only.
5. Handle Cameras with care. Cameras could be
damaged by improper handling or storage.
NETwORk
3. Do not expose the power Adapters to rain
or wet conditions. Water entering the Power
Adapters will increase the risk of electric shock.
4. Do not abuse the power Adapter cords. Never
use the cords for unplugging the plug from
the outlet. keep cords away from heat, oil,
sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
OpERATION
Service
Item 63842
For technical questions, please call 1-888-866-5797.
Page 3
Receiver Safety warnings
1. Maintain adequate airflow around Receiver.
2. Use supplied Power Adapter only.
SAFETy
3. Do not expose the power Adapter or
Receiver to rain or wet conditions. Water
entering the Power Adapter or Receiver
will increase the risk of electric shock.
4. Do not abuse the power Adapter cord. Never
use the cord for unplugging the plug from the
outlet. keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled
cords increase the risk of electric shock.
5. Maintain labels and nameplates on
the unit. These carry important safety
information. If unreadable or missing, contact
Harbor Freight Tools for a replacement.
6. People with pacemakers should consult their
physician(s) before use. Electromagnetic fields in
close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
7. The warnings, precautions, and instructions
discussed in this instruction manual cannot
cover all possible conditions and situations
that may occur. It must be understood by the
operator that common sense and caution are
factors which cannot be built into this product,
but must be supplied by the operator.
SETTINgS
SAVE THESE INSTRUCTIONS.
grounding
OpERATION
TO pREVENT ELECTRIC SHOCk AND DEATH FROM
INCORRECT gROUNDINg wIRE CONNECTION:
Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
Do not modify the power Adapter plugs provided. Do not use the equipment if the power cord or plug is
damaged. If damaged, have it repaired by a service facility before use. If the plug will not fit the outlet, have
a proper outlet installed by a qualified electrician.
1. The included Power Adapters do
not require grounding.
2. The Power Adapters may be used in
either of the 120 volt outlets shown in the
preceding illustration. (See Figure A.)
Figure A
Extension Cords
NETwORk
Note:
Page 4
Do not use extension cords with the Power Adapters.
For technical questions, please call 1-888-866-5797.
Item 63842
Specifications
Receiver
Recording
Power Rating
Operating Temperature
Camera Capacity
Memory
SAFETy
Audio
7" TFT LCD
GFSK
4 Mbps
800H x 480V RGB
Built-in Microphone
Speaker
Scheduled
Manual
Motion Detection
5VDC / 2A
14° - 104°F
4
SD Card - 256 GB max (not included)
SETTINgS
Screen
Modulation
Data Rate
Resolution
3.6mm
Effective Pixels
1280H x 720V
Night Vision Type
Infrared LEDs with Low Light Sensor
Image Type
Daylight: Color
Infrared: Black & White
Infrared Wavelength
850nm
Audio
Built-in Microphone
Speaker
Wireless Range
150 ft (indoors) 450 ft (outdoors)
Ingress Protection Rating
IP65 - Weather resistant
Night Vision Range
65 ft
Power Rating
9VDC / 600 mA
Operating Temperature
14° - 122°F
Transmission Frequency
2.4 GHz
NETwORk
Lens
OpERATION
Cameras
Item 63842
For technical questions, please call 1-888-866-5797.
Page 5
Set up - Before Use:
Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
SAFETy
Receiver Components and Controls
Back
Intercom
Activation
Volume
Record Button
Motion
Recording
Activation
Speaker
SETTINgS
power
Switch
Memory
Card Slot
5VDC
power Input
OpERATION
Stand
Network Connection
Figure B
NETwORk
Page 6
For technical questions, please call 1-888-866-5797.
Item 63842
Connect power
1. Connect the Power Adapter’s cord
to the back of the Receiver.
SAFETy
2. Plug the Power Adapter into a 120VAC outlet.
3. Turn the Power Switch to the ON position.
120VAC power
Adapter
NETwORk
OpERATION
SETTINgS
Figure C
Item 63842
For technical questions, please call 1-888-866-5797.
Page 7
Camera Components and Controls
Mounting
Bracket
Antenna
SAFETy
Microphone
9VDC power
Adapter
Lens
Infrared
Sensor
SETTINgS
Mounting
Hardware
Speaker
Back of Camera
Antenna
Connector
pair
Button
Figure D
Assembly
Thread the Antenna into the Antenna Connector on the back of the Camera.
OpERATION
Before Mounting
1. When planning mounting location and angle:
a. Verify that installation surface has no hidden
utility lines before drilling or driving screws.
b. Take into consideration the length of the
Camera and Power Adapter’s cords. Route the
cords so as to avoid a tripping hazard.
f. Make sure no strong light will shine
directly into Camera Lens.
g. Make sure location will remain within the
Camera's Operating Temperature.
2. Test each Camera's function in its
intended location before mounting:
c. Do not install where there are thick walls or other
obstructions between the Camera and Receiver.
a. Connect the Power Adapter’s cord
to the Camera’s Power cord.
d. Select a location high enough so that
it is out of reach of children, but still
covers the desired viewing area.
b. Plug the Power Adapter into a 120VAC outlet.
e. Do not install the Camera facing out of a window.
NETwORk
Page 8
c. Verify that there is an image on the Receiver.
Note: If there is no image, pair the Camera to the
Receiver according to pairing on page 11.
For technical questions, please call 1-888-866-5797.
Item 63842
d. Check the Camera's signal strength.
Toggle Joystick to check Camera 1.
3. Low signal adjustment:
a. Adjust the Camera and or/Receiver antenna(s).
Note: Toggle Joystick again to check other Camera(s).
b. Reposition the Camera and/or Receiver.
4. When the mounting location has been chosen:
good
Acceptable
a. Unplug the Power Adapter's
cord from the Camera.
Low
Needs
Adjustment
SAFETy
Excellent
Optimal
b. Using the Base as a template, mark
locations of mounting holes on
mounting surface. (See Figure F)
Figure E
5. Repeat all steps with the other Camera(s).
Mounting to Solid Surface
2. Position Mounting Bracket so that
mounting holes align with pilot holes.
3. Drive Screws through mounting holes in Base
and into pilot holes until the Mounting Bracket
is securely attached to the mounting surface.
4. Remove protective film from the Lens.
5. Loosen thumbscrews, adjust Camera as needed,
then tighten thumbscrews. (See Figure F)
Mounting to Hollow Surface
2. Tap Anchors into the holes until they are
almost flush with mounting surface.
3. Position Mounting Bracket so that Mounting
Holes align with anchor holes.
4. Drive Screws through mounting holes in Base
and into anchor holes until the Mounting Bracket
is securely attached to the mounting surface.
5. Remove protective film from the Lens.
6. Loosen thumbscrews, adjust Camera as needed,
then tighten thumbscrews. (See Figure F)
OpERATION
1. Using a drill bit slightly smaller than the
Anchors, drill holes in the marked locations.
SETTINgS
1. Using a drill bit slightly smaller than the Screws,
drill pilot holes into the marked locations.
Mounting
Holes
Mounting Base
Bracket
Figure F
1. Connect the Power Adapter’s cord
to the Camera’s Power cord.
Item 63842
NETwORk
Connect power
2. Plug the Power Adapter into a 120VAC outlet.
For technical questions, please call 1-888-866-5797.
Page 9
Viewing Modes
SAFETy
• Quad/Sequence Viewing - Automatic cycling
between Cameras.
Touch
to toggle between Quad mode (up
to 4 channels) and Auto Sequence mode.
• Single Camera - View one Camera at a time.
Touch
to switch between Cameras.
• Zoom - Push the
button on the
front of the Receiver to zoom in during
Single Camera Viewing Mode only.
Set Up
Menus
• Touch
to view Menus.
• Toggle the Joystick
Left/Right
to navigate through Menus.
• Click Ok (press Joystick) to
access highlighted Menu.
• Toggle Joystick again to navigate within Menus.
SETTINgS
• Touch
at any time to cancel an action
and/or go to the previous screen.
Menu > Settings
1. Touch
then select Settings.
2. Date & Time: Set date and time, then click
the Joystick to save and press
to exit.
Note: Time is in 24 hour format.
3. Default Settings: To return all Settings
to factory default settings. Select yes
or No, then click the Joystick.
OpERATION
4. Format Memory: Select yes or
No, then click the Joystick.
NOTICE: pressing Ok while yes is selected
will erase all files from the Micro SD Card.
5. Time Zone: Toggle Joystick Up/
Down to select your time zone
6. Firmware Upgrade: Select From SD
Card or From Server in order to install
an upgrade from either source.
7. Network: Here you can set your Network
Setting, review Network Information,
and reset your Password.
• Network Setting
a. If assigned a Static IP address, click Static Ip.
b. To set your IP Address, Subnet Mask, and
Default Getaway, click on each setting while
it is highlighted in green. A box will appear
over each number that is ready to be set.
c. Toggle Up/Down to set the correct numbers
for each setting, then click the Joystick once
to move on. When finished, select Ok.
Menu > Detect
1. Touch
then toggle right to select Detect.
2. Select Camera, then touch Ok.
3. Select Sensitivity Settings, then click the Joystick.
4. Repeat steps for other Cameras.
Menu > Alert
Toggle Left/Right to adjust receiver volume to your liking.
NETwORk
Menu > Record
1. Insert an SD card to enable recording.
A red chip will display to indicate the
card is functioning properly.
2. Touch
then select Record.
3. Motion Record:
Page 10
a. Duration: Select the amount of time to record
after motion has been detected, then Click Ok.
4. Schedule Record:
Note: Date and time must be set before setting up
Scheduled Recording. See Date & Time on page 10.
For technical questions, please call 1-888-866-5797.
Item 63842
b. Enter Start Time and End Time for the
desired camera, then click Save.
Note: Time is in 24 hour format.
c. Repeat steps for other days.
Note: For manual recording, see
Manual Recording on page 14.
a. Select yes to overwrite previously
recorded files when the SD card is full.
Note: After selecting yes,
will display
while in Auto Sequence mode.
b. Select No to keep all files.
SAFETy
a. Select a day to schedule, then click the Joystick.
Note: After selecting No, when the SD
card is full, the Receiver will stop recording
and the FULL indicator will display.
5. File Overwrite:
Menu > Camera
1. Touch
then toggle right to select Camera.
2. Use this menu to select between pairing,
Camera On/Off, Brightness, and Resolution.
Camera > pairing
1. Before installing Camera(s):
a. Connect the Power Adapter’s cord
to the Camera’s Power cord.
b. Plug the Power Adapter into a 120VAC outlet.
c. Determine which Channel is available to use.
d. Touch
SETTINgS
When adding Cameras, they will need to be programmed manually (paired) to work with the Receiver.
e. Select the Channel.
f. When prompted, press the Pair Button
on the back of the Camera.
2. Install Camera(s) according to
Mounting on page 9.
then select Camera > pairing.
Camera > Camera On/Off
then toggle right to select Camera.
2. Toggle Joystick up and down to select a Camera.
3. To turn the Camera off, toggle Right to select OFF.
4. To turn the Camera on, toggle Left to select On.
5. Repeat steps for other Cameras.
Camera > Brightness
To control the brightness of each Camera.
1. In the Camera menu, Toggle Down
to select Brightness.
2. When a camera is highlighted in green, Toggle
Right to increase brightness. Toggle Left to
decrease brightness, then click Joystick.
OpERATION
1. Touch
3. Repeat steps for other Cameras.
Camera > Resolution
NETwORk
Toggle Up/Down between cameras. When
the desired camera is highlighted in green,
Toggle Left/Right to select either VgA or HD
for that camera. Repeat for each camera.
Item 63842
For technical questions, please call 1-888-866-5797.
Page 11
Operating Instructions
Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this
manual including all text under subheadings therein before set up or use of this product.
SAFETy
Receiver Functions
SETTINgS
OpERATION
Icons
Menu
Channel Select
Quad/Sequence Viewing
Scan Mode
Joystick
• Scroll Up/Down/Left/
Right through menus
• Click to access
functions
Zoom
Delete File
• Delete the
highlighted file in
Playback mode
Figure g
NETwORk
Page 12
For technical questions, please call 1-888-866-5797.
Item 63842
Display Functions
cam1
Excellent Camera Signal
11 : 5 9 : 10
2 017 / 0 6 / 0 7
11 : 5 9 : 10
SETTINgS
2 017 / 0 6 / 0 7
SAFETy
REC
Date and Time Stamp
Time is in 24 hour format.
Overwrite Indicator
Good Camera Signal
• When Overwrite is set to Yes
• When visible, upgrade
is available.
No Camera Signal
• Out of Range
cam1
• Use path:
Menu>Settings>Firmware
Upgrade>From Server
• No Camera Plugged In
Current Camera Number
New File Indicator
OpERATION
Firmware Upgrade
Low Camera Signal
Volume off
Intercom Activated
Recording in Progress
NETwORk
REC
Figure H
Item 63842
For technical questions, please call 1-888-866-5797.
Page 13
Video Motion Detection
Note: Video Motion Detection overrides
Scheduled and Manual Recording.
SAFETy
To record all Cameras, touch
to set viewing Mode to 4 Camera.
To record the Camera that has been activated, set viewing Mode to Camera Sequence.
1. Touch
to open the Menus screen
and toggle right to select Detect.
2. Toggle Up/Down to select the desired
camera for Motion Detection.
3. Select Sensitivity Settings for Motion Detection
recording. Choose between High, Medium, Low
and Off. Press
to return to viewing mode.
4. When motion has been detected, recording will
begin.
REC will begin flashing.
Note: Recording will occur for the duration
specified in Recording Set up.
5. Touch
again to deactivate motion detection.
SETTINgS
OpERATION
NETwORk
Page 14
For technical questions, please call 1-888-866-5797.
Item 63842
Using Intercom
Allows audio communication between the Receiver and the Cameras.
Note: The Camera volume cannot be adjusted.
Touch
to increase volume.
Touch
to decrease volume.
Note:
SAFETy
Setting Receiver Volume
indicates Receiver volume is off.
Speaking through Intercom
1. Go to Single Camera mode for the individual
camera you wish to speak through.
2. Touch and hold the
Intercom Icon and speak in
a normal voice within 12 inches from the Receiver.
NETwORk
OpERATION
SETTINgS
3. Release the Icon to listen.
Item 63842
For technical questions, please call 1-888-866-5797.
Page 15
playback Files on Receiver
When there is a new recording, NEw will display and
To view Recordings:
SAFETy
1. In Live View Mode, click the Joystick
to view the Recording File List.
Note: Folders are organized by date, oldest to newest.
2. Select a date, then click the Joystick. Recordings
are organized by time, oldest to newest.
3. Select a recording, then click Joystick
to view the recording.
will flash.
a. Toggle Down then back Up to stop and go
back to the beginning of the recording.
Note: While stopped, Toggle Right
to view the next recording.
b. Toggle Up to pause and also to resume playback.
c. Toggle Left to rewind.
d. Toggle Right to fast forward.
playback Files on Other Device
1. Remove the SD card from the Receiver.
3. Follow device's instructions to view files.
SETTINgS
2. Insert SD card into device's card slot.
Delete Files
IMpORTANT: DO NOT DELETE FILES
USINg A COMpUTER. ONLy DELETE
FILES USINg THE SySTEM.
2. Select file to delete.
1. In Live View Mode,click the Joystick
to access Recording File List.
4. Select yes or No, then touch Ok.
3. Press and release X on the front of the Receiver.
OpERATION
NETwORk
Page 16
For technical questions, please call 1-888-866-5797.
Item 63842
TO CONNECT ON AN IpHONE OR IpAD:
TO CONNECT ON AN ANDROID:
1. Connect the included Ethernet cable from the
Ethernet port on the LCD receiver to your wireless
router. The network icon will turn green.
1. Connect the included Ethernet cable from the
Ethernet port on the LCD receiver to your wireless
router. The network icon will turn green.
Note: You may need to turn the
receiver off and on again.
Note: You may need to turn the
receiver off and on again.
2. Download the MyCam View app from the
App Store. Once installed, launch the app.
2. Download the MyCam View app from the Google
Play Store. Once installed, launch the app.
3. Press the Add Device icon.
3. Press Click here to add device.
4. At the Add Device screen (see Figure K),
add a device manually by pressing Add
OR by pressing QRCode to scan the QR
code on the back of the receiver.
4. Enter device information on the
next screen (see Figure L).
SETTINgS
• UID - Enter the UID printed below the
QR code OR press Scan to scan the
QR code on the back of the receiver.
• Name - Create a personalized
name for the system.
Figure I
5. Enter the following information on the next screen:
SAFETy
Remote Viewing Via MyCam View App
• password - Enter the password
(Default: 000000).
• Name - Create a personalized
name for the system.
• password - Enter the device
password (Default: 000000).
6. Press Save. The system status will
read Online in your device list.
Figure J
5. Press OK. The system status will
read Online in your device list.
OpERATION
• UID - Enter the UID printed below the
QR code on the back of the receiver. If
you tapped QRCode in Step 4, this
field will populate automatically.
6. Tap the name of the system and you will be
asked to enter a new, secure password.
NETwORk
7. Tap the name of the system and you will be
asked to enter a new, secure password.
Item 63842
For technical questions, please call 1-888-866-5797.
Page 17
Maintenance Instructions
procedures not specifically explained in this manual must be performed only by a qualified
technician.
SAFETy
Camera Maintenance
TO pREVENT SERIOUS INJURy FROM ELECTRIC SHOCk:
Unplug the power Adapter from its electrical outlet
before inspection, maintenance, or cleaning.
1. pERIODICALLy, inspect the general
condition of the Camera. Check for:
• loose hardware,
• damaged cord/electrical wiring,
SETTINgS
• cracked or broken parts, and
2. pERIODICALLy, wipe external surfaces
of Camera with clean cloth.
3. Maintain area surrounding Camera,
making sure obstacles don’t interfere with
visibility, such as overgrown bushes.
• any other condition that may
affect its safe operation.
Troubleshooting
problem
possible Causes
Likely Solutions
OpERATION
Receiver does not
display image.
1. Camera disconnected.
2. Camera out of range of Receiver.
1. Check power to Camera.
2. Relocate Camera and/or Receiver.
Picture is white.
Camera pointing at strong light source.
Reposition Camera.
Picture is choppy.
1. Obstructions between
Camera and Receiver.
2. Frame rate too low.
1. Remove obstructions between
Camera and Receiver.
2. Increase frame rate.
SD card error.
Turn Receiver off, remove and reinsert
SD card, then turn receiver back on.
Note: If "Err" still appears, reformat
the card or use a different one.
"Err" appears
on the screen.
NETwORk
Page 18
For technical questions, please call 1-888-866-5797.
Item 63842
NOTE: this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try and correct the interference by one or more of the following measures:
SAFETy
FCC NOTICE:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NETwORk
OpERATION
SETTINgS
The antenna used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or
operated in conjunction with any other antenna or transmitter.
Item 63842
For technical questions, please call 1-888-866-5797.
Page 19
Limited 90 Day warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability
standards, and warrants to the original purchaser that this product is free from defects in materials and
workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage
due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities,
criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event
be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential
damages arising from the use of our product. To the extent that this product is used with software other than
what is provided, we shall in no event be liable for any damage to your computer or loss of data. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of
exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges
prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may
elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will
return repaired products at our expense, but if we determine there is no defect, or that the defect resulted
from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • pO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Download PDF