HK2299
Copyright
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may
be reproduced without written consent of the author.
© Copyright 2017
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations
and pending applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
All other product names used in this manual are the properties of their respective owners and are
acknowledged.
Ver.:02
—i—
DLP Projector—User’s Manual
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause
personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
General Safety Information






Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
Note:
As with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015
— ii —
Preface
Projector Installation Notice

Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be
installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease
dramatically, and may lead to other unpredictable damages.
15°
-15°

Allow at least 50 cm clearance around the exhaust vent.
Minimum 500mm
(19.69 inch)
Minimum 500mm
(19.69 inch)
Minimum 500mm
(19.69 inch)

Minimum 100mm
(3.94 inch)
Minimum 500mm
(19.69 inch)



Minimum 300mm
(11.81 inch)
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed operation temperature while the projector is running, and the
air intake and exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable operation temperature range.
–iii –
DLP Projector—User’s Manual
Verify Installation Location

To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper
grounding and equalized ground potential for all of the equipment in the Projector System.

The power code provided with the Projector should be used. In case of any missing item, other
qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use
2-blade power cord.
 Verify if the voltage is stable, grounded properly and there is no electricity leakage.
 Measure total power consumption which should not higher the safety capacity and avoid safety
issue and short circuit.
 Turn on Altitude Mode when located in high altitude areas
 The projector can only be installed upright or inverted.
 When installation the bracket, make sure the weight limit is not exceed and firmly secured.
 Avoid installing near air conditioner duct or subwoofer.
 Avoid installing at high temperature, insufficient cooling and heavy dust locations.
 Keep your product away from fluorescent lamps (> 1 meter) to avoid malfunction
caused by IR interference
 Install the projector above 200cm to avoid damage.

The power cord and signal cable should be connected before power on the projector. During the
projector starting and operating process, DO NOT insert or remove the signal cable or the power
cord to avoid damaging the projector.
Cooling notes
Air outlet
 Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.
 Air outlet location should not be in front of the lens of other projector to avoid causing illusions.
 Keep the outlet at least 100cm away from the inlets of other projectors
 The projector generates a massive amount of heat during use. The internal fan dissipates the heat
of the projector when shutting down, and such process may continue for a certain period. After the
project enters STANDBY MODE status, press the AC power button to turn off the projector and
remove the power cord. DO NOT remove the power cord during the shutdown process, as it may
cause damage to the projector. In the meantime, the delayed heat radiating will also affect the
service life of the projector. The shutdown process may vary depending on the model used.
Whatever the case may be, be sure to disconnect the power cord till after the projector enters the
STANDBY status.
Air inlet
 Make sure there is no object blocking air input within 30 cm.
 Keep the inlet away from other heat sources
 Avoided heavy dust area
— iv —
Preface
Power Safety



Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 28
for clear and safe instructions for this procedure. Before replacing the lamp:


Unplug the power cord.
Allow the lamp to cool for about one hour.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards
to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and
broken shards of the lamp.
Cleaning the Projector


Unplug the power cord before cleaning. See Cleaning the Projector page 32.
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on
page 43.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
–v –
DLP Projector—User’s Manual
Main Features
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Ultra HD 4K (3840 x 2160) resolution for outstanding details and stunning visuals
DLP® DarkChip3™ and BrilliantColor™ technologies for optimal black levels and vibrant colorful
images
2000 ANSI lumens for an amazing brightness
Advanced video processor for fluid video streaming and 12-bit programmable RGB colour
adjustments
High Dynamic Range (HDR10) for enriched brightness and impeccable vibrancy for precise natural
colors
REC 709 for an incredible cinematic like movie experience
Six segment RGBRGB color wheel delivers outstanding reds, greens and blue color reproductions
Fine tune and optimize an image with advanced calibrations, including gamma and color
management settings
Advanced HDMI 2.0 (x3) connectors for high quality digital video signals and quick data transfer
rates
Audio ready with built-in 10 watt speaker and audio out port
Long lasting energy efficient lamps that last up to 4000 hours
Wide 1.5x zoom range and vertical lens shift for greater installation convenience and flexibility
Full functioning remote control and intuitive 9 key menu pad for easy control
Dual infrared sensors for handy remote control from either in front or behind the projector
Anti-theft security features include: Kensington® security slot, security bar, and PIN lock keypad
About this Manual
This manual is intended for end users and describes how to install and operate the DLP projector.
Wherever possible, relevant information—such as an illustration and its description—has been kept on
one page. This printer-friendly format is both for your convenience and to help save paper, thereby
protecting the environment. It is suggested that you only print sections that are relevant to your needs.
— vi —
Preface
Table of Contents
GETTING STARTED ........................................................................................................................................................... 1
PACKING CHECKLIST .............................................................................................................................................1
VIEWS OF PROJECTOR PARTS................................................................................................................................2
Front-right View ...............................................................................................................................................2
Rear view .........................................................................................................................................................3
Rear view—On-screen Display (OSD) buttons ...............................................................................................4
Bottom view .....................................................................................................................................................5
REMOTE CONTROL PARTS .....................................................................................................................................6
REMOTE CONTROL OPERATING RANGE ..................................................................................................................8
PROJECTOR AND REMOTE CONTROL BUTTONS .......................................................................................................8
INSERTING THE REMOTE CONTROL BATTERIES .......................................................................................................9
SETUP AND OPERATION............................................................................................................................................... 10
STARTING AND SHUTTING DOWN THE PROJECTOR ................................................................................................10
ADJUSTING THE PROJECTOR LEVEL .....................................................................................................................12
ADJUSTING THE VERTICAL IMAGE POSITION ...........................................................................................................13
ADJUSTING THE ZOOM AND FOCUS .......................................................................................................................13
ADJUSTING THE VOLUME .....................................................................................................................................14
ON-SCREEN DISPLAY (OSD) MENU SETTINGS ...................................................................................................... 15
OSD MENU CONTROLS .......................................................................................................................................15
Navigating the OSD .......................................................................................................................................15
SETTING THE OSD LANGUAGE .............................................................................................................................16
OSD MENU OVERVIEW........................................................................................................................................17
MAIN MENU.........................................................................................................................................................19
IMAGE SETTINGS .................................................................................................................................................20
COLOR SETTINGS ................................................................................................................................................21
HSG Adjustment ............................................................................................................................................22
LAMP CONTROL...................................................................................................................................................23
SETUP ................................................................................................................................................................24
Menu Settings................................................................................................................................................25
ADVANCED ..........................................................................................................................................................26
INFORMATION MENU ............................................................................................................................................27
MAINTENANCE AND SECURITY .................................................................................................................................. 28
REPLACING THE PROJECTION LAMP .....................................................................................................................28
Resetting the Lamp .......................................................................................................................................31
CLEANING THE PROJECTOR .................................................................................................................................32
Cleaning the Lens..........................................................................................................................................32
Cleaning the Case .........................................................................................................................................32
USING THE PHYSICAL LOCK .................................................................................................................................33
Using the Security Bar ...................................................................................................................................33
TROUBLESHOOTING ...................................................................................................................................................... 34
COMMON PROBLEMS AND SOLUTIONS ...................................................................................................................34
TIPS FOR TROUBLESHOOTING ..............................................................................................................................34
LED ERROR MESSAGES ......................................................................................................................................35
IMAGE PROBLEMS ...............................................................................................................................................35
LAMP PROBLEMS .................................................................................................................................................36
REMOTE CONTROL PROBLEMS.............................................................................................................................36
AUDIO PROBLEMS ...............................................................................................................................................36
HAVING THE PROJECTOR SERVICED .....................................................................................................................36
HDMI Q & A .......................................................................................................................................................37
SPECIFICATIONS ............................................................................................................................................................. 38
SPECIFICATIONS ..................................................................................................................................................38
PROJECTION DISTANCE VS. PROJECTION SIZE ......................................................................................................39
Projection Distance and Size Table ..............................................................................................................39
–vii –
DLP Projector—User’s Manual
TIMING MODE TABLE ...........................................................................................................................................40
PROJECTOR DIMENSIONS ....................................................................................................................................42
REGULATORY COMPLIANCE ....................................................................................................................................... 43
FCC WARNING ...................................................................................................................................................43
CANADA ..............................................................................................................................................................43
SAFETY CERTIFICATIONS .....................................................................................................................................43
APPENDIX I ........................................................................................................................................................................ 44
OP COMMAND.....................................................................................................................................................44
— viii —
DLP Projector—User’s Manual
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
DLP PROJECTOR
OF
F
ON
Day
ht
Nig
ure
Pictode
M
M
t
Exi
u
en
nk
Bla
e
ez
Fre
te
Mu
REMOTE CONTROL
(WITH TWO AAA BATTERIES)
CD-ROM
(THIS USER’S MANUAL)
POWER CORD
HDMI CABLE
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
Caution:
Avoid using the projector in dusty environments.
–1–
DLP Projector—User’s Manual
Views of Projector Parts
Front-right View
ITEM
LABEL
DESCRIPTION
1.
Lamp cover
Removes cover to replace lamp module.
2.
IR receiver
Receive IR signal from remote control.
3.
Lens
Projection Lens.
4.
Focus ring
Focuses the projected image.
5.
Zoom ring
Enlarges the projected image.
6.
LENS SHIFT
For Image vertical shift adjustment.
7.
LAMP LED
Flashing
Error code
8.
TEMP LED
Red
Over Temperature, T1 error
9.
POWER LED
Green
Ready to power on (Standby)
Flashing
Start warm up, Cooling, Error code
SEE PAGE
13
13
35
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
—2—
DLP Projector—User’s Manual
Rear view
1 2
11
ITEM
LABEL
34 5 6 7 8
9
10
DESCRIPTION
SEE PAGE
1.
AUDIO OUT
Connect an AUDIO cable to an audio amplifier.
2.
IR receiver
Receive IR signal from remote control.
3.
USB POWER
(5V/1.5A)
Connect the USB cable for power supply.
4.
MINI USB
Connect the USB cable from a computer.
5.
RS-232C
Connect RS-232 serial port cable for remote control.
6.
HDMI 1
Connect the HDMI cable from a HDMI device.
7.
HDMI 2
Connect the HDMI cable from a HDMI device.
8.
HDMI 3
Connect the HDMI cable from a HDMI device.
9.
Security Bar
For security and authorized usage.
33
10.
AC IN
Connect the POWER cable.
10
11.
Function keys
See Rear view—On-screen Display (OSD) buttons.
4
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
–3–
DLP Projector—User’s Manual
Rear view—On-screen Display (OSD) buttons
1
9
ITEM
1.
2
3
4
DESCRIPTION
MENU
Navigates and changes settings in the OSD
3.
Navigates in the OSD
ENTER
Enter or confirm highlighted OSD menu item
5.
Turns the projector On or Off
6.
Navigates and changes settings in the OSD
7.
AUTO
Optimizes image size, position, and resolution
8.
9.
Navigates in the OSD
SOURCE
Note:
Keystone (
/
SEE PAGE
Opens and exits OSD menus
2.
4.
6
7
8
LABEL
5
Enter the Source menu
/
/
) function is unavailable in this model.
—4—
15
DLP Projector—User’s Manual
Bottom view
235.0mm
50.0mm
70.0mm
1
78.8mm
95.0mm
110.0mm
1
70.0mm
ITEM
LABEL
70.0mm
DESCRIPTION
SEE PAGE
1.
Tilt adjustor
Rotate adjuster lever to adjust angle position.
2.
Ceiling support holes
Contact your dealer for information on mounting the projector on a
ceiling
12
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 8 mm (0.31 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment over a period of 60 seconds.
–5–
DLP Projector—User’s Manual
Remote Control Parts
ON
OFF
30
1
29
3
28
Picture
Mode
27
Menu
Night
Day
5
Exit
7
2
4
6
8
26
9
10
22
20
11
25
12
24
14
23
15
21
16
19
Mute
Freeze
Blank
13
17
18
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency
fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path
between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
—6—
DLP Projector—User’s Manual
ITEM
LABEL
DESCRIPTION
1.
OFF
Turns the projector off.
2.
HDMI 2
Toggles the input sources for display between HDMI sources.
3.
HDMI 3
Toggles the input sources for display between HDMI sources.
4.
Night
Switch the picture mode to Night mode.
5.
Day
Switch the picture mode to Day mode.
6.
7.
SEE PAGE
Navigates and changes settings in the OSD.
EXIT
15
Goes back to previous OSD menu, exits and saves menu settings.
8.
Enters and confirms settings in the OSD.
9.
Navigates and changes settings in the OSD.
10.
Navigates and changes settings in the OSD.
11.
4:3
Displays 4:3 aspect ratio.
12.
16:10
Displays 16:10 aspect ratio.
13.
Native
Displays Native aspect ratio.
14.
2.35:1
Displays 2.35:1 aspect ratio.
15.
Volume
Displays the volume setting bar.
16.
HDR
Turns on the HDR mode.
17.
Blank
Toggles the screen between blank and normal.
18.
Freeze
Freeze/unfreezes the on-screen picture.
19.
Mute
Toggles the built-in speaker between on and off.
20.
Contrast
Displays the contrast setting bar.
21.
Brightness
Displays the brightness setting bar.
22.
Auto (Resync)
Switch again to resync current source.
23.
Source
Displays the source selection bar.
24.
Fill
Displays Fill aspect ratio.
25.
16:9
Displays 16:9 aspect ratio.
26.
15
Navigates and changes settings in the OSD.
27.
Menu
Opens the OSD.
28.
Picture Mode
Navigates and switches to each picture mode settings.
29.
HDMI1
Toggles the input sources for display between HDMI sources.
30.
ON
Turns the projector on.
–7–
15
14
14
15
15
15
DLP Projector—User’s Manual
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the projector. All operations
can be carried out with the remote control; however, the buttons on the projector are limited in use.
—8—
DLP Projector—User’s Manual
Inserting the Remote Control Batteries
1.
Remove the battery compartment
cover by sliding the cover in the
direction of the arrow.
2.
Insert the battery with the positive
side facing up.
3.
Replace the cover.
Caution:
1. Only use AAA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
4. RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
5. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
–9–
DLP Projector—User’s Manual
SETUP AND OPERATION
Starting and Shutting down the Projector
1.
Connect the power cord to the
projector. Connect the other end to
a wall outlet.
The
POWER LED on the
projector light.
2.
Turn on the connected devices.
3.
Ensure the POWER LED not a
flashing. Then press the
POWER
button to turn on the projector.
The projector splash screen displays
and connected devices are
detected.
4.
If more than one input device is
connected, press the SOURCE
button and use ▲▼ to scroll among
devices.
•
HDMI 1: High-Definition Multimedia Interface.
•
HDMI 2: High-Definition Multimedia Interface.
•
HDMI 3: High-Definition Multimedia Interface.
— 10 —
DLP Projector—User’s Manual
5.
When the “Power Off? / Press
Power again” message appears,
press the POWER button. The
projector turns off.
Caution:
Do not unplug the power cord until the power LED stops flashing–indicating the projector has
cooled down.
– 11 –
DLP Projector—User’s Manual
Adjusting the Projector Level
Take note of the following when setting up the projector:



The projector table or stand should be level and sturdy.
Position the projector so that it is perpendicular to the screen.
Ensure the cables are in a safe location. You could trip over them.
To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired
angle has been achieved.
— 12 —
DLP Projector—User’s Manual
Adjusting the vertical image position
The Lens Shift function
can be used to adjust
the position of the
vertically.
The display position can
be shifted upward up to
15% and down to 10%
elevation of the display.
Lens shift adjustable range
15%V
Shift range
15%
Shift to top
1V
10%V
Shift range
Lens shift center position
Adjusting the Zoom and Focus
1.
Use the Image-zoom
control (on the projector
only) to resize the
projected image and
screen size
.
2.
Use the Image-focus
control (on the projector
only) to sharpen the
projected image
.
– 13 –
10%
DLP Projector—User’s Manual
Adjusting the Volume
1.
Press the Volume buttons on the
remote control.
The volume control appears on
the display.
2.
Press the ◄► buttons on the
keypad or remote control to adjust
Volume +/-
3.
Press the MUTE button to turn off
the volume. (This feature is
available only on the remote).
— 14 —
DLP Projector—User’s Manual
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the projector to navigate and make
changes to the OSD. The following illustration shows the corresponding buttons on the projector.
5
5
1
3
2
3
4
5
1
2
4
6
8
9
9
7
1. To enter the OSD, press the
MENU button.
2. There are seven menus. Press
the cursor ▲▼ button to move
through the menus.
3. Press
(Enter) or ► button
into submenu. Press the cursor
▲▼ button to move up and
down in submenu.
4. Select one of the submenu,
Press
(Enter) or ► button
into the selected item. Press
▲▼or ◄► to change values
for settings.
5. Press MENU to close the OSD
or leave a submenu.
– 15 –
8
7
6
DLP Projector—User’s Manual
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button. Press the cursor ▲▼ button to navigate to Setup. Press
(Enter) or ► to enter the Setup submenu.
2. Press the cursor ▲▼ button until MENU Settings is highlighted. Press
enter the MENU Settings submenu.
(Enter) or ► to
3. Press the cursor ▲▼ button to select Language menu. Press
(Enter) to display
language. Press the cursor ▲▼ button until the language you want is highlighted.
4. Press the MENU button twice to close the OSD.
— 16 —
DLP Projector—User’s Manual
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
Main Menu
Source
Sub Menu
Image
Picture Mode
Settings
HDMI 1, HDMI 2, HDMI
3
Movie, Presentation,
Day, Night, User
1.8, 2.0, 2.2, 2.4,
S-curve
0 ~ 100
0 - 100
0 - 100
0 - 100
0 - 10
Off, On
Reset current picture
mode
Warm, Normal, Cold
Gamma
Brightness
Contrast
Saturation
Hue
Sharpness
Freeze
Reset
Color
Color
Temperature
HSG
Red
Green
Blue
Yellow
Cyan
Magenta
White
Reset
Hue, Saturation, Gain
Hue, Saturation, Gain
Hue, Saturation, Gain
Hue, Saturation, Gain
Hue, Saturation, Gain
Hue, Saturation, Gain
Red, Green, Blue
– 17 –
0~199
0~199
0~199
0~199
0~199
0~199
0~199
DLP Projector—User’s Manual
Main Menu
Lamp
Control
Setup
Advanced
Information
Sub Menu
Power Mode
Lamp Hour Reset
Aspect Ratio
High Altitude
Orientation
Settings
Boost, Default
Auto Power Off
Auto Power On
Startup Logo
Blank Screen
Auto Source
Menu Settings
Off, On
Off, On
Off, On
Black, Purple, Blue, White
Off, On
English, Français, Español,
Deutsch, Português, 簡体中文,
繁體中文, 日本語, 한국어
Fill, 4:3, 16:9, 16:10, Native, 2.35:1
Off, On
Front Table, Front Ceiling, Rear
Table, Rear Ceiling
Language
Menu Position
Top Left, Top Right, Bottom Left,
Bottom Right, Center
Time Out
Always, 10 Seconds, 30 Seconds,
60 Seconds
HDR Control
HDR Settings
Model Name
Software Version 1
Software Version 2
Software Version 3
Active Source
Signal Format
Lamp Hours
Reset All
Auto, Off
Normal, Details, User
— 18 —
DLP Projector—User’s Manual
Main Menu
Press the MENU button to open the Main menu.
ITEM
DESCRIPTION
Source
Press
(Enter) to enter and select the source.
Image
Press
(Enter) / ► to enter the Image sub menu. See Image Settings on page 20.
Color
Press
(Enter) / ► to enter the Color sub menu. See Color Settings on page 21.
Lamp Control
Press
(Enter) / ► to enter the Lamp Control sub menu. See Lamp Control on
page 23.
Setup
Press
(Enter) / ► to enter the Setup sub menu. See Setup on page 25.
Advanced
Press
(Enter) / ► to enter the Advanced sub menu. See Advanced on page 24.
Information
Press
(Enter) / ► to enter the Information sub menu. See Information Menu on
page 27.
– 19 –
DLP Projector—User’s Manual
Image Settings
Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Image
menu. Press
(Enter) / ► to enter the Image sub menu. Press ▲▼ button to move up and down
in the Image item. Press
(Enter) / ► to entry item. Press ▲▼ or ◄► to change values for
settings.
ITEM
DESCRIPTION
Picture Mode
Press
(Enter) to enter to set the Picture Mode.
Gamma
Press
(Enter) to enter and adjust the Gamma correction of the display.
Brightness
Press
(Enter) / ► to enter to adjust the display Brightness.
Contrast
Press
(Enter) / ► to enter to adjust the display Contrast.
Saturation
Press
(Enter) / ► to enter to adjust the Saturation.
Hue
Press
(Enter) / ► to enter to adjust the Hue.
Sharpness
Press
(Enter) / ► to enter to adjust the display sharpness level.
Freeze
Press
(Enter) to enter and enable or disable the Freeze.
Reset
Press
(Enter) to reset current picture mode.
— 20 —
DLP Projector—User’s Manual
Color Settings
Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Color
menu. Press
(Enter) / ► to enter the Color sub menu. Press ▲▼ button to move up and down in
the Color item. Press
(Enter) / ► to entry item. Press ▲▼ to change values for settings.
ITEM
DESCRIPTION
Color Temperature
Press
(Enter) to enter to set the Color Temperature.
HSG
Press
(Enter) / ► to enter the HSG (Hue/Saturation/Gain) sub menu.
See SG Adjustment on page 22
– 21 –
DLP Projector—User’s Manual
HSG Adjustment
Press the
(Enter) / ► button to enter the HSG Adjustment sub menu. Press ▲▼ button to move
up and down in the HSG item. Press
(Enter) / ► to entry item. Press ▲▼ to change values for
settings.
ITEM
DESCRIPTION
Red
Select to enter the Red Color Manager.
Press
(Enter) / ► to enter and to adjust the Hue, Saturation, and Gain.
Green
Select to enter the Green Color Manager.
Press
(Enter) / ►to enter and to adjust the Hue, Saturation, and Gain.
Blue
Select to enter the Blue Color Manager.
Press
(Enter) / ► to enter and to adjust the Hue, Saturation, and Gain.
Yellow
Select to enter the Yellow Color Manager.
Press
(Enter) / ► to enter and to adjust the Hue, Saturation, and Gain.
Cyan
Select to enter the Cyan Color Manager.
Press
(Enter) / ► to enter and to adjust the Hue, Saturation, and Gain.
Magenta
Select to enter the Magenta Color Manager.
Press
(Enter) / ► to enter and to adjust the Hue, Saturation, and Gain.
White
Select to enter the White Color Manager.
Press
(Enter) / ► to enter and to adjust the Red, Green, and Blue.
Reset
Press
(Enter) to execute and HSG will be reset to default values
— 22 —
DLP Projector—User’s Manual
Lamp Control
Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Lamp
Control menu. Press
(Enter) / ► to enter the Lamp Control sub menu. Press ▲▼ button to
move up and down in the Lamp Control item. Press
(Enter) / ► to entry item. Press ▲▼ to
change values for settings.
ITEM
DESCRIPTION
Power Mode
Press
(Enter) to enter and select the Power mode for higher brightness or lower
brightness to save lamp life.
Lamp Hour Reset
After replacing the lamp, this item should be reset. See page 31 for more information
on Resetting the Lamp.
– 23 –
DLP Projector—User’s Manual
Setup
Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the Setup
menu. Press
(Enter) / ► to enter the Setup sub menu. Press ▲▼ button to move up and down
in the Setup item. Press
(Enter) / ► to entry item. Press ▲▼ to change values for settings.
ITEM
DESCRIPTION
Aspect Ratio
Press
(Enter) to enter and adjust the video aspect ratio.
High Altitude
Press
(Enter) to enter and select the High Altitude mode On or Off.
Note: Recommend selecting high speed when the altitude of the environment is
higher than 1500m ( 4921ft ).
Orientation
Press
Auto Power Off
Press
(Enter) to enter to set the Auto Power Off timer. The projector automatically
turns off if no input source is detected after the preset period of time.
Auto Power On
Press
(Enter) to enter and enable or disable automatic power On when AC power
is supplied.
Startup Logo
Press
(Enter) to enter and enable or disable Startup Logo
Blank Screen
Press
(Enter) to select different color to blank the screen.
Auto Source
Press
(Enter) to enter and enable or disable automatic source detection.
Menu Settings
Press
(Enter) / ► to enter the Menu Settings sub menu. See Menu Settings on
page 29.
(Enter) to enter and select different projection style for projector.
— 24 —
DLP Projector—User’s Manual
Menu Settings
Press the
(Enter) / ► button to enter the Menu Settings sub menu. Press ▲▼ button to move up
and down in the Menu Settings item. Press
(Enter) / ► to entry item. Press ▲▼ to change
values for settings.
ITEM
DESCRIPTION
Language
Press
(Enter) to enter to select a different localization Menu.
Menu Position
Press
(Enter) to enter to select a different OSD location.
Time Out
Press
(Enter) to enter to select OSD timeout delay.
– 25 –
DLP Projector—User’s Manual
Advanced
Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the
Advanced menu. Press
(Enter) / ► to enter the Advanced sub menu. Press ▲▼ button to
move up and down in the Advanced item. Press
(Enter) / ► to entry item. Press ▲▼ to change
values for settings.
ITEM
DESCRIPTION
HDR Control
Press
(Enter) to enter and enable or disable HDR Control.
HDR Settings
Press
(Enter) to enter and select the HDR effect settings.
— 26 —
DLP Projector—User’s Manual
Information Menu
Press the MENU button to open the OSD menu. Press the cursor ▲▼ button to move to the
Information menu. Press
(Enter) / ► to enter the Information sub menu. Press ▲▼ button to
move up and down in the Information item.
ITEM
DESCRIPTION
Model Name
Displays the activated input source.
Software Version 1
Showing system software version.
Software Version 2
Showing system software version.
Software Version 3
Showing system software version.
Active Source
Displays the activated source.
Signal Format
Showing the Timing of the Projector.
Lamp Hours
Displays the number of hours the lamp has been in use.
Reset All
Press
(Enter) to reset all settings to default values.
Note:
Status displayed in this menu is for viewing only and cannot be edited.
– 27 –
DLP Projector—User’s Manual
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local
authority.
Warning:
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to
do so could result in a severe burn.
Caution:
In rare cases the lamp bulb may burn out during normal operation and cause glass dust or shards
to be discharged outward from the rear exhaust vent.
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.
Always keep your face away from the exhaust vent so that you do not suffer from the gas and
broken shards of the lamp.
When removing the lamp from a ceiling-mounted projector, make sure that no one is under the
projector. Glass fragments could fall if the lamp has been burned out.
IF A LAMP EXPLODES
If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come
out of the exhaust vent. The gas contains toxic mercury.
Open windows and doors for ventilation.
If you inhale the gas or the shards of the broken lamp enter your eyes or mouth, consult the doctor
immediately.
1.
Loosen the two screws on
the lamp compartment
cover.
— 28 —
DLP Projector—User’s Manual
2.
Remove the lamp
compartment cover.
3.
Remove the three screws
from the lamp module.
4.
Lift the module handle up.
5.
Pull firmly on the module
handle to remove the lamp
module.
– 29 –
DLP Projector—User’s Manual
6.
Reverse steps 1 to 5 to
install the new lamp
module.
While installing, align the
lamp module with the
connector and ensure it is
level to avoid damage.
Note:
The lamp module must sit
securely in place and the
lamp connector must be
connected properly before
tightening the screws.
— 30 —
DLP Projector—User’s Manual
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
1.
Press the MENU button to open
the OSD menu.
2.
Press the cursor ▼▲button to
move to the Lamp Control menu.
(Enter) / ► to enter the
Press
Lamp Control sub menu.
3.
Press the cursor ▼▲ button to
move down to Lamp Hour Reset.
4.
Press
(Enter) to adjust the
settings.
5.
Press the MENU button to get
back to Lamp Control.
– 31 –
DLP Projector—User’s Manual
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the
projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to
the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and
then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
— 32 —
DLP Projector—User’s Manual
Using the Physical Lock
Using the Security Bar
In addition to the password protection function and the Kensington lock, the Security Bar helps
protect the projector from unauthorized removal. See the following picture.
– 33 –
DLP Projector—User’s Manual
TROUBLESHOOTING
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose
connection. Check the following before proceeding to the problem-specific solutions.
•
•
•
•
•
•
Use some other electrical device to confirm that the electrical outlet is working.
Ensure the projector is turned on.
Ensure all connections are securely attached.
Ensure the attached device is turned on.
Ensure a connected PC is not in suspending mode.
Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when
calling for technical support or for passing on to service personnel.
— 34 —
DLP Projector—User’s Manual
LED Error Messages
ERROR CODE MESSAGES
POWER LED
GREEN
TEMP LED
RED
LAMP LED
RED
Standby
ON
OFF
OFF
Start warm up
Flashing(Green)
OFF
OFF
Lamp Ready
Green
OFF
OFF
Cooling
Flashing(Green)
OFF
OFF
1W MCU detects scaler stops working
2 blinks
OFF
OFF
(initial fail)
Over Temperature
OFF
ON
OFF
Thermal Break Sensor error
4 blinks
OFF
OFF
Lamp strike fail / ballast connector open
5 blinks
OFF
OFF
Lamp voltage too low
5 blinks
OFF
7 blinks
Ballast fail
5 blinks
OFF
8 blinks
Ballast communication fail
5 blinks
OFF
10 blinks
Ballast over temp
5 blinks
OFF
1 blinks
Lamp fail
5 blinks
OFF
5 blinks
Fan 1 error
6 blinks
OFF
1 blinks
Fan 2 error
6 blinks
OFF
2 blinks
Fan 3 error
6 blinks
OFF
3 blinks
Fan 4 error
6 blinks
OFF
4 blinks
Fan 5 error
6 blinks
OFF
5 blinks
Case Open
7 blinks
OFF
OFF
DMD error
8 blinks
OFF
OFF
T1 error
OFF
ON
1 blinks
Color wheel error
9 blinks
OFF
OFF
ASIC not ready
8 blinks
OFF
1 blinks
Lamp Blower stops(Not running.)
5 blinks
OFF
6 blinks
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting
the projector. If the Power or Lamp LEDs are still blinking or any other situation that isn't listed in the chart
above, please contact your service center.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto button on the remote control.
3. Ensure the projector-to-screen distance is within the specified range.
4. Check that the projector lens is clean.
Problem: The image is reversed
Check the Orientation setting on the Setup menu of the OSD.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Image menu of the OSD.
– 35 –
DLP Projector—User’s Manual
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the Color and Image menu of the
OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is on.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Power LED
is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the battery.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Test the source audio output with other speakers.
5. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in
the original carton. Include a description of the problem and a checklist of the steps you took when
trying to fix the problem: The information may be useful to service personnel. For servicing, return the
projector to the place you purchased it.
— 36 —
DLP Projector—User’s Manual
HDMI Q & A
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI
cable?
Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or HighSpeed cables.
˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or
up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.
˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz
or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable
and can successfully handle 1080p signals including those at increased color depths and/or
increased refresh rates from the Source. High-Speed cables are also able to accommodate
higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).
Q. How do I run HDMI cables longer than 10 meters?
There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective
distance from the typical 10 meter range to much longer lengths. These companies
manufacture a variety of solutions that include active cables (active electronics built into
cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and
fiber solutions.
Q. How can I tell if a cable is an HDMI certified cable?
All HDMI products are required to be certified by the manufacturer as part of the HDMI
Compliance Test Specification. However, there may be instances where cables bearing the
HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively
investigates these instances to ensure that the HDMI trademark is properly used in the
market. We recommend that consumers buy their cables from a reputable source and a
company that is trusted.
For more detail information check http://www.hdmi.org/learningcenter/faq.aspx#49
– 37 –
DLP Projector—User’s Manual
SPECIFICATIONS
Specifications
Model
HK2299
Display Type
0.66" TRP UHD
Resolution
3840 x 2160
Projection Distance
1.2 ~ 10 m
Projection Screen Size
Projection Lens
26.0" ~ 324.9"
Manual Focus/Manual Zoom
Throw Ratio
1.39~2.09
Projection Methods
Front, Rear, Desktop/Ceiling (Rear, Front)
Data Compatibility
VGA, SVGA, XGA, WXGA, SXGA, SXGA+, UXGA, WUXGA, Mac
SDTV/EDTV/ HDTV
480i, 480p, 720p, 1080i, 1080p, UHD
Safety Certification
UL/CUL, FCC, CB/CE, CCC, PCT, PSB, KC+KCC, SASO
Operation Temperature
5° ~ 40°C
Environmental Storage
Condition
-10° ~ 60°C, 5% to 95% (No condensation)
Dimensions
Ac Input
Power Consumption
427.2 mm (W) x 379.7 mm (D) x 172.1 mm (H)
AC Universal 100-240V
450W (Normal), <0.5W (Standby)
Lamp
310W
Audio Speaker
7W x1 (10W peak)
Input Terminals
HDMI x 3
Output Terminals
PC Audio jack(3.5mm) x 1
RS-232C
Control Terminals
USB (Type mini B) - service only
USB (type A) support DC 5V
Security
Security Bar
Note: For questions regarding product specifications, please contact your local distributor.
— 38 —
DLP Projector—User’s Manual
Projection Distance vs. Projection Size
Projection Distance and Size Table
HK2288
IMAGE
DIAGONAL
IMAGE WIDTH
PROJECTION
DISTANCE
FROM
IMAGE HEIGHT
PROJECTION
DISTANCE
TO
OFFSET-A
(INCH)
(INCH)
(CM)
(INCH)
(CM)
(INCH)
(CM)
(INCH)
(CM)
(MM)
60
52.3
132.8
29.4
74.7
72.7
184.6
109.3
277.6
0.0
70
61.0
155.0
34.3
87.2
84.8
215.4
127.5
323.9
0.0
72
62.8
159.4
35.3
89.7
87.2
221.5
131.1
333.1
0.0
80
69.7
177.1
39.2
99.6
96.9
246.2
145.7
370.1
0.0
84
73.2
186.0
41.2
104.6
101.8
258.5
153.0
388.6
0.0
90
78.4
199.2
44.1
112.1
109.0
276.9
163.9
416.4
0.0
96
83.7
212.5
47.1
119.6
116.3
295.4
174.9
444.2
0.0
100
87.2
221.4
49.0
124.5
121.1
307.7
182.2
462.7
0.0
120
104.6
265.6
58.8
149.5
145.4
369.2
218.6
555.2
0.0
135
117.7
298.9
66.2
168.1
163.5
415.4
245.9
624.6
0.0
150
130.7
332.1
73.5
186.8
181.7
461.6
273.2
694.0
0.0
200
174.3
442.7
98.1
249.1
242.3
615.4
364.3
925.3
0.0
– 39 –
DLP Projector—User’s Manual
Timing Mode Table
Signal Format
PC
Apple Mac
SDTV
EDTV
HDMI1 /HDMI2 /HDMI3
Resolution
Frame Rate HZ
640x480
59.94
○
-
-
-
640x480
640x480
800x600
800x600
800x600
848x480
848x480
1024*768
1024*768
1024*768
1280x720
1280x1024
1280x1024
1280x1024
1600x1200
1920x1080
1680x1050
1920x1200 RB
1920x1200 RB
1400X1050
1366 x 768
1440 x 900
1280 x 768
1280 x 800
1280 x 960
640x480
832x624
480i
1440x480i
1440x576i
576i
480p
576p
74.99
85
60.32
75
85.06
47.95
59.94
60
75
85
47.95
60.02
75.02
85.02
60
47.95
59.94
50
60
60
60
60
60
60
60
66.59
74.54
59.94
60
50
50
59.94
50
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
○
-
-
-
-
-
-
-
○
○
○
○
— 40 —
RGB
8-bit YUV 10-bit YUV 12-bit YUV
○
○
○
○
-
-
-
-
○
○
○
○
○
○
○
○
DLP Projector—User’s Manual
Signal Format
HDTV
PsF formats
Resolution
Frame Rate HZ
1035i
1080i
1080i
1080i
720p
720p
720p
1080p
1080p
1080p
1080p
1080p
1080p
1080p
1080p
2K
4K
4K
1080sf
1080sf
60
50
59.94
60
50
59.94
60
23.98
24
25
29.97
30
50
59.94
60
24/25/30/50/60
24/25/30
50/60
30
25
HDMI1 /HDMI2 /HDMI3
RGB
8-bit YUV 10-bit YUV 12-bit YUV
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○(8 Bits)
○
○(4:2:2)
○(4:2:2)
-
-
-
-
-
-
-
-
O:Frequency supported
—:Frequency not supported
3840x2160 did not supported 3D function and timing.
– 41 –
DLP Projector—User’s Manual
Projector Dimensions
— 42 —
172.1mm(6.78")
152.5mm(6.0")
379.7mm(14.95")
427.2mm(16.82")
DLP Projector—User’s Manual
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
UL/CUL, FCC, CB/CE, CCC, PCT, PSB, KC+KCC, NOM, SASO
– 43 –
DLP Projector—User’s Manual
APPENDIX I
OP Command
The RS-232 Commands use only ASCII characters which can be entered using a typical terminal emulator
like Windows HyperTerminal with the following setting:
RS232 Setting
Baud rate:
9600
Parity check:
None
Data bit:
8
Stop bit:
1
Flow Control
None
Note: that each input character will be echoed on the terminal by system and there is no need to set the
local echo “ON” with the terminal setting.
Note: that “Unknown Command” is echoed on the terminal by system when system state is stand by and
low power mode is “ON” if the input command is other than “op power.on [CR]”/ “op status [CR]”.
System Operation commands.
The Operation commands tell the projector what to do. All commands start with 2 letters: “op” for operations commands, and a space [SP] then following a control command then finally the value wants to read,
set, increase or decrease. All commands must end with a carriage return (ASCII hex 0D), shown as [CR]
below. The syntax for operations commands is as follows:
op[SP]<operation command>[SP]<Setting Value>[CR]
For all but Execute functions the response from the projector will be the command and “= <value>” where
<value> is the current value or “NA” if the value is not available. For Execute functions the response will
be the same command. All responses will be in CAPS. Please refer to the following table for command
list and examples:
System Operation command:
Operation
Commands
Values
Set
= <value>
Makes the unit take that value.
Get
?
Asks what the current value is.
Execute
(none)
Performs an action such as a reset.
Get operations command example:
Input: op brightness ? [CR]
System Response: OP BRIGHTNESS = 50
Set operations command example:
Input: op brightness = 100 [CR]
System Response: OP BRIGHTNESS = 100
Execute command example:
Input: op pict.reset [CR]
System Response: OP PICT.RESET
— 44 —
DLP Projector—User’s Manual
Operation
Commands Values
source
=?
pict.mode
=?
brightness
contrast
=?
=?
gamma
=?
saturation
hue
sharpness
=?
=?
= ?
freeze
= ?
pict.reset
(execute)
color.temp
= ?
hsg.hue.r
hsg.hue.g
hsg.hue.b
hsg.hue.c
hsg.hue.m
hsg.hue.y
hsg.sat.r
hsg.sat.g
hsg.sat.b
hsg.sat.c
hsg.sat.m
hsg.sat.y
hsg.gain.r
hsg.gain.g
hsg.gain.b
hsg.gain.c
hsg.gain.m
hsg.gain.y
hsg.white.r
hsg.white.g
hsg.white.b
hsg.reset
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
=?
(execute)
lamp.mode
=?
lamp.hour.reset
0 = HDMI1
1 = HDMI2
2 = HDMI3
0 = Movie
1 = Presentation
2 = Day
3 = Night
4 = User
0 - 100
0 - 100
0 = 1.8
1 = 2.0
2 = 2.2
3 = 2.4
4 = S-curve
0 - 100
0 - 100
0 - 10
0 = Off
1 = On
Notes
Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Reset current picture mode parameters
to default value.
0 = Warm
1 = Normal
2 = Cold
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 - 199
0 = Boost
1 = Default
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note1,Note4
Note2,Note4
Note4
Clear User Lamp Hours
(Include Boost/Default hours)
(Not includes System Total Hours).
(execute)
– 45 –
DLP Projector—User’s Manual
Operation
Commands Values
aspect.ratio
=?
high.altitude
=?
orientation
=?
auto.poweroff
=?
auto.poweron
=?
auto.source
=?
startup.logo
=?
blank.screen
=?
menu.settings.lang
=?
menu.settings.menupos = ?
menu.settings.timer
=?
hdr.control
=?
hdr.settings
=?
model.name
sw.version1
sw.version2
sw.version3
act.source
signal
lamp.hours
reset.all
?
?
?
?
?
?
?
(execute)
0 = Fill
1 = 4:3
2 = 16:9
3 = 16:10
4 = Native
5 = 2.35:1
1 = On
0 = Off
0 = Front Table
1 = Front Ceiling
2 = Rear Table
3 = Rear Ceiling
0 = Off
1 = On
0 = Off
1 = On
0 = Off
1 = On
0 = Off
1 = On
0 = Black
1 = Purple
2 = Blue
3 = White
0 = English
1 = French
2 = Spanish
3 = German
4 = Portuguese
5 = Chinese Simplified
6 = Chinese Traditional
7 = Japanese
8 = Korean
0 = Top Left
1 = Top Right
2 = Bottom Left
3 = Bottom Right
4 = Center
0 = Always On
1 = 10 Seconds
2 = 30 Seconds
3 = 60 Seconds
0 = Auto
1 = Off
0 = Normal
1 = Details
2 = User
<string>
<string>
<string>
<string>
<string>
<number>
— 46 —
Notes
Note1,Note4
Note4
Note4
Note4
Note4
Note4
Note4
Note3,Note4
Note4
Note4
Note1,Note4
Note1,Note4
Note4
Note4
Note4
Note4
Note4
Note1,Note4
Note4
Note4
DLP Projector—User’s Manual
Operation
Commands Values
Notes
power.on
power.off
(execute)
(execute)
Note4
power
=?
0 = Off
1 = On
Note4
Note1:Not support when no input source.
Note2:Not support in 3 min after system power on.
Note3:Not support when input source is locked and image presents.(But Still adjustable.)
Note4:Not support when system has already powered on and splash logo finished.
– 47 –
Download PDF