591217C DW60 installA4 NZAU.indd

DISHWASHER
DW60 models
INSTALLATION GUIDE
NZ AU
591217C
12.17
1
!
SAFETY AND WARNINGS
!
IMPORTANT SAFETY INSTRUCTIONS
WARNING!
Electrical shock hazard
Before installing the dishwasher, remove the house fuse or open the circuit
breaker.
This appliance must be earthed. In the event of a malfunction or breakdown,
earthing will reduce the risk of electric shock by providing a path of least
resistance for electric current. This appliance is equipped with a cord having
an equipment-earthing conductor and an earthing plug. The plug must be
plugged into an appropriate outlet that is installed and earthed in accordance
with all local codes and ordinances.
WARNING- Improper connection of the equipment-earthing conductor can
result in a risk of electric shock. Check with a qualified electrician or service
representative if you are in doubt as to whether the appliance is properly
earthed.
Do not modify the power supply plug provided with the appliance - if it will
not fit the outlet, have a proper outlet installed by a qualified electrician. Do
not use an extension cord, adapter plug or multiple outlet box.
Failure to follow this advice may result in electrical shock or death.
WARNING!
Cut Hazard
Take care - panel edges are sharp.
Failure to use caution could result in injury or cuts.
●
●
●
●
●
●
●
●
●
●
●
●
●
IMPORTANT SAFETY INSTRUCTIONS
●
●
●
●
●
●
●
●
●
●
Installation of this dishwasher requires basic mechanical and electrical skills.
Be sure to leave these Instructions with the Customer.
Installation must comply with your local building and electricity regulations.
At the completion of the dishwasher installation, the Installer must perform the Final
Checklist.
Remove all packaging materials supplied with the dishwasher.
This dishwasher is manufactured for indoor use only.
Ensure all water connections are turned OFF. It is the responsibility of the plumber and
electrician to ensure that each installation complies with all Codes and Regulations.
The dishwasher MUST be installed to allow for future removal from the enclosure if service
is required.
The switched power outlet must be outside the dishwasher cavity, so that it is accessible
after installation.
Care should be taken when the appliance is installed or removed to reduce the likelihood
of damage to the power supply cord and hoses.
●
If the dishwasher is to be relocated from one installation to another it must be kept
upright to avoid damage from water spillage.
Make sure only new hoses are used for connection (supplied with the dishwasher). Old
hoses should not be reused.
Failure to install the dishwasher correctly could invalidate any warranty or liability claims.
If the power supply cord is damaged, it must be replaced by a dealer or Authorised
Repairer or a similar qualified trades person in order to avoid a hazard.
Ensure the dishwasher is placed between cabinetry. Failure to do so may result in an
unstable product, which may cause damage or injury.
Do not operate this appliance if it is damaged, malfunctioning, partially disassembled or
has missing or broken parts, including a damaged power supply cord or plug.
Do not store or use petrol, or other flammable vapours and liquids in the vicinity of the
dishwasher.
Connect to a properly rated, protected and sized power supply circuit to avoid electrical
overload.
Make sure that the power supply cord is located so that it will not be stepped on, tripped
over or otherwise subject to damage or stress.
Do not install or store the dishwasher where it will be exposed to temperatures below
freezing or exposed to weather.
Do not use an extension cord or a portable electrical outlet device (e.g. multi-socket
outlet box) to connect the dishwasher to the power supply.
This appliance must be earthed. In the event of a malfunction or breakdown, earthing
will reduce the risk of electric shock by providing a path of least resistance for electric
current.
This appliance is equipped with a cord having an equipment-earthing conductor and a
earthing plug. The plug must be plugged into an appropriate outlet that is installed and
earthed in accordance with all local codes and ordinances.
EARTHING INSTRUCTIONS - This appliance must be connected to a earthed metal,
permanent wiring system, or an equipment-earthing conductor must be run with the
circuit conductors and connected to the equipment-earthing terminal or lead on the
appliance.
IMPORTANT!
SAVE THESE INSTRUCTIONS
1
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our
website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
2
3
PARTS SUPPLIED
TECHNICAL DATA
Technical data
Check the electrical data on the rating label (located on the left-hand side of the
dishwasher’s stainless steel inner door). Should the data on the rating label be different
to those specified below, consider those on the rating label as correct.
Drain hose
support (1)
Inlet hose (1)
Rubber washer
for inlet hose (2)
(comes already
fitted)
DW60FC1 models
DW60FC2
DW60FC4
DW60FC6 models
Capacity
14 place settings
15 place settings
Mains water
pressure
0.03-1 MPa
(= 0.3-10 bar)
0.03-1 MPa
(= 0.3-10 bar)
Power voltage
230-240 V (50 Hz)
220-240 V (50Hz)
Maximum current
intensity
10 A
10 A
Total absorbed
power
1900-2050 W
1720-2050 W
Colour
White
DW60FC1W1
DW60FC2W1 DW60FC4W1
DW60FC6W1
Stainless Steel
DW60FC1X1
DW60FC2X1 DW60FC4X1
DW60FC6X1
Anti-flood protection
Installation and
User Instructions
This dishwasher has anti-flood protection, which will stop the water flowing in the event
of a leak within the machine.
4
PRIOR TO INSTALLATION
Unpacking and handling
●
●
●
●
●
Check packaging and dishwasher for signs of transport damage. If the dishwasher is in any way damaged, do not install it. Contact the dealer the dishwasher was purchased from.
Disposal of packaging: some of the packaging is recyclable. Check the symbols and labels and recycle if possible.
Never lift the dishwasher from the door handle or the top panel. Doing so may cause damage.
Always be careful with the hoses and power cord at the back of the dishwasher. Careful handling will prevent damage and malfunction from squashing, kinking or cuts.
While installing the dishwasher, check the drain hose is not restricted or kinked.
Connections and services
●
●
●
●
Check that the power cord is long enough to reach the outlet. If it isn’t, it must be replaced by a Fisher & Paykel authorised technician. Extension cords or multi-outlet power boards should not
be used to connect the dishwasher to the power supply.
Check that the hoses are long enough to reach the services. If a hose needs extending, ensure that the extension hose is new and of equal quality and diameter to the one already fitted. Note:
the drain hose should not be longer than 4 m, as a longer drain hose will cause reduced performance.
The dishwasher should not be connected to a water system where the temperature exceeds 60oC, or where there is no temperature control, e.g. wetback system, unless the system is fitted with a
suitable tempering valve.
The dishwasher must not be connected to an undersink high-pressure “push-through” type hot water system, as damage to the system will result.
2
5
PRODUCT DIMENSIONS
C
Top panel (removable)
PRODUCT DIMENSIONS
MM
A Overall height of product
with top panel in place
with top panel removed*
A
850 - 870**
820 - 840**
B Overall width of product
597
C Overall depth of product
600
D
595
Depth of open door (measured from front of kickstrip)
CABINETRY DIMENSIONS
MM
E Inside height of cavity
PLAN
with top panel in place
with top panel removed*
PROFILE
B
855 - 875**
825 - 845**
F Minimum inside width of cavity
600
G
605
Minimum inside depth of cavity
* The top panel may be removed to suit underbench cavity height. See instructions opposite.
**Depending on feet height adjustment.
C
E
FRONT
F
G
D
ISO
3
6
CAVITY PREPARATION
IMPORTANT!
Preparing the product and cabinetry
To prevent possible steam damage to the cabinetry, ensure
that any bare wood surrounding the dishwasher is sealed
with an oil-based paint or moisture-proof polyurethane.
The top panel may be removed to
suit underbench cavity height. See
the illustrations below.
1
IMPORTANT!
The power outlet
must be located in a
cabinet adjacent to the
dishwasher cavity.
5
Unscrew the top
panel at the rear
either side
6
Dia. 50mm
3
2
Slide forward (2)
20-30mm, then lift off (3)
●
●
4
Services can be located
either side of the
dishwasher.
Ensure that any services
hole has a minimum
diameter of 50mm.
Levelling and positioning the dishwasher
●
●
●
●
Before sliding the dishwasher into position, adjust the feet with a spanner (4) to ensure
that the dishwasher is level and the required height (5). Take care when pushing the
product into the cavity that you do not bend the feet.
Do not lift the dishwasher from the door handle or top panel.
As you push product in, pull through hoses and cord, ensuring they don’t get kinked or
twisted (6).
We recommend that you adjust the feet so that the dishwasher sits securely under the
bench top so that it doesn’t tip.
4
PLUMBING AND DRAINAGE OPTIONS. DETERMINE WHICH IS MORE SUITABLE.
Dishwasher and Ø 38 mm Standpipe
Dishwasher using drain hose joiner
onto sink trap/waste tee
2
1
3
1
step 8
min. 750 mm
38 mm
step 8
min. radius
200 mm
750 - 882.5 mm
min.
120mm
min. 500 mm
2
If space is limited
for fixing, push
hose through drain
hose support
to required height
750-882.5 mm
If space is limited
for fixing, push
hose through drain
hose support
to required height
Installer to provide
drain hose joiner to suit
min. 15mm waste tee
750-882.5 mm
7
min. radius
200 mm
Ensure drain hose is routed
straight to joiner. Remove excess
drain hose material if necessary.
Do not shorten the inlet hose.
5
IMPORTANT!
Do not connect the drain hoses
to a Waste Disposal Unit, as this
type of connection may lead to a
blockage in the drain hoses.
8
9
CONNECT INLET HOSE TO COLD WATER
PLUG PRODUCT IN
min.
10mm
3/4” BSP connector
180o
No leaks!
Ensure the supplied
rubber washer is
fitted inside the
coupling.
2
1
Tighten coupling
with spanner.
Electrical connection
Plumbing -- Water inlet connection
●
●
IMPORTANT!
●
The appliance should be connected to the water main using the new water inlet hose supplied.
Old hoses should not be used.
Do not shorten the inlet hose.
●
1 Take note of water connection requirements.
●
The dishwasher has a single valve water connection.
●
We recommend a cold water connection for best performance and energy efficiency.
●
The incoming water temperature should not exceed 25oC.
2 Take note of the permitted water pressure extremes.
●
Lowest: 0.3 bar = 3 N/cm2 = 30kPa
●
Where pressure is below 1 bar, contact a qualified plumber.
●
Highest: 10 bar = 100 N/cm2 = 1MPa
●
Where pressure is above 10 bar, a pressure reduction valve must be installed. Contact a qualified
plumber.
3 Connect the water inlet hose to an accessible water tap with a 3/4” BSP connector. Ensure that
there is no kink in the inlet hose that could restrict the flow of water. A 90o bend requires a
minimum height of 200mm for a kink-free curve.
●
Ensure incoming water is clear. If the water pipes have not been used for a long period of time,
let the water run to make sure it is clear with no impurities. Not doing so may result in the water
inlet hose getting blocked and damaging the appliance.
●
If required, use a filter insert to filter out deposits from the piping. The filter insert is
available from your Authorised Service Centre or Customer Care.
4 Tighten the hose coupling a further half turn after seal contact.
5 Check that the connection does not leak.
●
The dishwasher must not be connected to the electrical supply while installation
is being carried out. Ensure all domestic wiring is properly earthed.
Check the rating label (located on the left-hand side of the dishwasher’s stainless
steel inner door) and ensure that the voltage and frequency values for the
current in the house correspond to those on the rating label.
Insert the plug into a properly earthed power outlet that has a disconnection
switch.
IMPORTANT!
●
●
●
The earthing of the appliance is a safety requirement mandated by law.
If the power cord is not long enough to reach the outlet or the outlet to which
the appliance must be connected is not appropriate for the plug, the entire
dishwasher power cord must be replaced. This should only be done by a Fisher
& Paykel authorised technician. Do not modify or cut the plug. Do not use an
adaptor, extension cord, or multi-outlet power board to connect the dishwasher
to the power supply, as these could cause overheating and create a fire hazard.
The outlet into which the dishwasher is plugged must remain easily accessible
(e.g. in an adjacent cabinet) even when the appliance is installed. This is to
ensure that the dishwasher can be disconnected from the power supply for safe
cleaning and maintenance.
6
!0
●
●
TROUBLESHOOTING
Excessive water remaining above the filter plate, after the rinse cycle (This can be displayed as an A20 fault)
Check for a kinked drain hose, blocked waste connection, highloop not properly installed, drain hose not routed correctly or spray arms not in place.
No water supply (This is displayed as an A10 fault)
Check water is connected and turned on.
●
The dishwasher is beeping continuously
There is a fault. See section ‘How to attend to a fault’ in the User guide for further information and instructions.
●
Water around water supply and drainage connections
Check connections, existing plumbing and hoses for leaks. Check rubber washer and hose clamp are correctly fitted.
●
If product is tipping
The product is not secure under the benchtop. Ensure the product is level and placed between cabinetry. Adjust the feet so that the dishwasher sits securely under the benchtop.
●
If a problem occurs, consult the ‘Troubleshooting’ section of the User guide.
●
If after checking these points you still need assistance, please refer to the Service & Warranty book for warranty details and your nearest Authorised Service Centre, or contact us through our
website, listed below.
7
!1
FINAL CHECKLIST
TO BE COMPLETED BY THE INSTALLER
Check all parts are installed.
Check that the door opens and closes freely without resistance to adjacent
cabinetry.
Ensure that all panels and parts thereof are secure and final electrical tests have been
conducted in accordance with local electrical regulations.
Check that the electrical outlet is accessible and located in an adjacent cupboard.
Check that the dishwasher is level. If necessary, adjust the levelling feet slightly. To ensure
optimum performance, the dishwasher should not be inclined more than 1o. Check with a
spirit level.
Ensure inlet hose to water supply has supplied rubber washer fitted, and that it’s
tightened a further half turn after seal contact.
Ensure any knockouts or plugs in drain connection have been drilled out and drain
connection has been made.
Check the operation of the dishwasher:
to turn the dishwasher on.
1 Press
2 Select the Rinse programme:
●
Press
to scroll through the wash programmes to get to Rinse.
3 Press
to start the Rinse programme. Can you hear the dishwasher filling?
4 When the Rinse programme is over (approx. 20 minutes), check that the water has
drained.
If a fault code appears, see the ‘Fault codes’ section of the User guide for advice.
The drain hose joiner must not support the weight of excess hose material. Keep drain
hose as fully extended as possible to prevent sagging. Any excess length of drain hose
should be kept on the dishwasher side of the highloop.
If connecting the drain hose to the sink trap, ensure the Highloop is a minimum 150mm
higher than the drain hose joiner.
Ensure any packaging or tape securing the racks is removed from the dishwasher.
Complete and keep for safe reference:
Model
Serial No.
Purchase Date
Purchaser
Dealer Address
Installer’s Name
Installer’s Signature
Installation Company
Installation Date
8
9
10
FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2017. All rights reserved.
The product specifications in this booklet apply to the specific products
and models described at the date of issue. Under our policy of continuous
product improvement, these specifications may change at any time. You
should therefore check with your Dealer to ensure this booklet correctly
describes the product currently available.
NZ AU
591217C
12.17
Download PDF