CloudControl™
CloudControl™
SETUP GUIDE - HOW TO CONNECT YOUR SPA TO THE INTERNET
CONTROL YOUR SPA
In Your Backyard • In Your House • In Your Office • Any Wi-Fi Hotspot • Any 3G/4G Data Network
CloudControl
TM
TM
instructions for installing the app
1
What You Need
On a
Android ™
Device
A smart device
(Android™, iPhone® or iPad®)
After downloading the bwa™ app
an icon should appear on your smart
device main screen just like below.
Bullfrog Spas
Scan QR Code
To Go Directly To
Google Play
Wireless Internet Connection
(3G, 4G, or Wi-Fi hot spots)
Finished Installation
2
Download App
Bullfrog Spas
Open Google
Play Store
3
On a
iPhone ®
or iPad ®
Search for
“CloudControl”
“Bullfrog Spas”
Download the App
Bullfrog Spas
Scan QR Code
To Go Directly To
The App Store
Bullfrog Spas
Note: If you don’t see the icon on
your main screen, repeat step 2 again.
Open The
App Store
Search for
“CloudControl”
“Bullfrog
Spas”
For additional information please visit the “Info” page within the app after download or visit bullfrogspas.com/cloudcontrol.
0713BPWI-FI_42238
0713BPWI-FI_42238
©2013 Balboa Water Group. Single
Source
Solution.
rightsSingle
reserved.
©2013
Balboa
Water All
Group.
Source Solution. All rights reserved.
1382 Bell Avenue | Tustin, CA 1382
92780Bell |Avenue
p 714.384.0384
www.balboawater.com
| Tustin, CA| 92780
| p 714.384.0384 | www.balboawater.com
Balboa has the right to change technical
datahas
without
notice.
iPhonetechnical
and iPad data
are registered
trademark of Apple Inc. Android is a trademark of Google Inc.
Balboa
the right
to change
without notice.
Download the App
CloudControlTM
TM
instructions for installing the module
1
Package Contents
2
Connecting The Wi-Fi Module
Make sure the clip is
in the correct position
You will hear a CLICK
once connected.
STOP
1-2-3 Easy Installation Guide
bwa™ Welcome Kit
Make sure your spa
is turned OFF before
you continue
Y-Splitter (25657)
SYSTEM
SIDE VIEW
Note: Black Wi-Fi cable.
bwa™ Wi-Fi Module (50350)
After the Wi-Fi wire module is inserted,
gently pull on the wire to make sure the clip
is securely in place and will not come loose.
3
Finished Installation Overview
Note: Place the
Wi-Fi module
away from any
metal tub
supports.
For additional information on installing the module please visit your Authorized Bullfrog Spas Dealer.
0713BPWI-FI_42238
©2013 Balboa Water Group. Single Source Solution. All rights reserved.
1382 Bell Avenue| Tustin, CA 92780 | p 714.384.0384 | www.balboawater.com
Balboa has the right to change technical data without notice.
WARNING!
If you do not see the Wi-Fi
connector from your system.
Please contact an electrician
or your local spa technician to
connect the Wi-Fi connector
for you. DO NOT OPEN THE
SPA SYSTEM AND ATTEMPT
TO CONNECT THE WI-FI
CONNECTOR YOURSELF.
The high electrical voltage
may harm or kill you.
TABLE OF CONTENTS
1. Control Your Hot Tub From Your Smartphone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Getting Ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3. CloudControl™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
4. Helpful Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5. Frequently Asked Questions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6. Wireless Troubleshooting Issues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
7. Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 - 25
Control Your Hot Tub From Your Smartphone
CloudControl™ , is an app for your smart device (Android™ or iPhone®) that allows you to access your hot tub via a direct connection anywhere
in the local proximity of your tub, anywhere in your house that you can connect to your local
Wi-Fi network, or anywhere in the World you have an Internet connection to your smart device via 3G, 4G, or Wi-Fi hot spots*.
With the CloudControl, you can ensure that your hot tub will be ready whenever you want to take a dip. Instead of going outside and pressing buttons on the topside panel, the app lets you start the tub and change settings from your smartphone or tablet.
The app provides full interface control so you can set the temperature, turn pumps on and off and even set filtration cycles.
You can access your tub from the
comfort of inside your home, your
office before you leave work, or on your way
back from your get-a-way holiday.
You can set your own mood and
personal settings, so your tub is set
to how you like when you arrive.
* Check with your carrier for Internet charges as the CloudControl app transmits data to & from a server and depending on your data plan, you may experience additional monthly data
charges.
5
Getting Ready
You’re just several easy steps away from connecting
your tub to your home network and the Internet.
Before you begin, you might want to record some information for your records and to help troubleshoot your
setup if needed.
STOP!
Before you continue on you need to know your wireless name, password and encryption.
If you don’t please contact your adminstrator, the
person(s) who helped setup your home wireless
router, or check your equipment manuals. You will
also need to make sure you have wireless internet
connection at your tub.
Equipment Configuration
______________________________________________________
BP System Serial Number (Located on your spa system)
______________________________________________________
Wi-Fi Module S/N (Located on your CloudControl™ module)
______________________________________________________
Smart Device (Is your smart device an iPhone, iPad, Galaxy 4S,..etc?)
______________________________________________________
Smart Device OS (What is your smart phone operating system?)
______________________________________________________
Wi-Fi Router Manufacturer
______________________________________________________
Internet Provider (Time Warner, DSL, Dish, etc)
______________________________________________________
Cellular Data Provider (Is your smart phone data 3G or 4G?)
______________________________________________________
Local / Home Network SSID (What is your home wireless network name?)
______________________________________________________
Key (Password) (What is your home wireless password)
______________________________________________________
Encryption (None, WEP, WPA) (What is your home wireless security.)
6
Make sure you are near your tub. Go to your Wi-Fi set-
Step 1
Download the Bullfrog Spas-CloudControl app to your
smart device from either the Google® Play or the iTunes®
store. Once you have it loaded on your phone you are
ready to
tings screen and look for the BWG SPA network (it will
be named similar to BWGSpa_12345). In our example
it is BWGSpa_0E608F and connect to it. No password is
needed.
connect to your hot tub.
Scan the QR code below to take you directly to
the the download page.
Google® Play Store
iTune® App Store
Step 2
Make sure your device’s Wi-Fi is turned on.
(Check with your device instructions on how to
access your Wi-Fi settings).
For this example we are using an Android™ device, iOS®
would be similar.
7
Step 3
Once you are connected to the BWG Spa network, start
the CloudControl app and follow the prompts on the
screen. (Your start screen maybe different.)
FROM YOUR START
SCREEN
WAIT UNTIL YOU
ARE CONNECTED
CLOUDCONTROL APP
MAIN SCREEN
When connected, you
will be taken to the
main app screen.
You are now directly connected
to your hot tub and can control
all the hot tub functions via the
CloudControl™ app.
CloudContr...
Press the CloudControl app button.
8
Connect to the spa.
If you do not have a home Internet network, you can stop
The easiest way to check if you can see your home Internet net-
here. If you do not have a home Internet network,
work from your tub, is to try and connect to it with your smart
you will be able to control your tub while you are in
device next to the tub. Open a browser window and
the near proximity of 65 feet or 20 meters.
connect to the Internet (or any other app that connects
The detailed operation of the CloudControl app is ex-
to the Internet).
plained in the app user guide which can be found here:
While standing at your tub, if you can connect your smart device
http://www.bullfrogspas.com/cloudcontrol
to the Internet through your home network, then the tub Cloud-
If you have a home Internet network the next step
is to connect your tub to it.
Before you connect to your home Internet network you
must be able to see your home network from
your tub.
Control Wi-Fi module should be able to connect to your home
network also.
If you cannot connect to the Internet through your
home network, you may need to move your router
or add a repeater or some other signal booster so you can see
your network at your tub.
It is not possible to connect to the spa via “the cloud” without a
third “device” such as a network router, or device used as a hot
spot. If no third device exists the CloudControl module operates
in local direct connect mode only.
9
You can also try moving the Wi-Fi module to a
You are now ready to connect your tub to your local / home net-
different spot where you do have coverage in
work. Press the Settings button.
your yard.
Or hang it on the outside of the tub instead
of under the skirt of the tub.
Once you can see your home network you are ready.
On the next screen, you will select the Advanced button to set
Step 4
Setting up your Local / Home Wi-Fi is a one-time process.
Once connected, you will not need to change your settings
again unless your network SSID changes.
10
up your Wi-Fi network settings
Cloud Control
SETTINGS SCREEN
ADVANCED SETTINGS
The Settings screen allows you
to select the temperature of
the spa, change the
temperature between
Fº & Cº, set time of day,
filter cycles and more.
Now select the Wi-Fi
Settings button, to select your
home network and enter your
password.
On the Wi-Fi screen you can use
the drop down menu to
select your network SSID or you
can enter it in the SSID box.
If you have a router that supports
WPS provisioning, select that
box and press the WPS button on
your home router.
For Android™ setup continue on
to the next page, for iOS® setup
skip to Page 14.
You will also need to choose the
type of password
encryption you are using: Open,
WEP, or WPA.
Not all routers support the WPS
function. Check your router’s
instructions for more details.
Press the Advanced button
to setup your Wi-Fi.
THE WI-FI SCREEN
Note: CloudControl™ clouds currently
only
support Open, WEP, and WPA.
11
Cloud Control
ENTER PASSWORD SCREEN
Select the Key text box to
enter your password if you
have one. Type it in using
the keyboard.
Use the back/return
key when finished entering
your password. (Android™
use back key).
12
CONFIRM SCREEN
Now you will save the password
to the hot tub and the tub will
be ready to connect to your
network.
Press the Save Button.
WI-FI LINK SCREEN
You will be asked to confirm
that you want to update your
password to the spa.
You may need to connect to
your home network after you
save the password.
The BWG Spa network will
now disconnect and you will
be controlling your tub via
your home network.
Exit the app and make sure you
are connected to your home
network.
Cloud Control
YOUR SMARTPHONE
WI-FI SCREEN
CLOUDCONTROL WEP
SETUP
CLOUDCONTROL WSP
SETUP
If you have your home
network setup to automatically
connect, the CloudControl
app will re-connect.
Restart the app and connect
to the tub which will now be
connected to your local/ home
network.
iOS setup is similar to
Android except you will need
to type in your SSID and Key (Password) using your keyboard.
If you have a router that supports WPS provisioning, select
that button and press the WPS
button on your home router.
You may need to manually
connect to your local/ home
network.
You can now control your tub
anywhere you can connect to
your local / home network.
To continue the setup, go
to Page 14.
You will also need to choose
the type of password encryption
you are using: Open, WEP,
or WPA.
Not all routers support
the WPS function. Check
your router’s instructions
for more details.
Note: CloudControl™ clouds currently only
support Open, WEP, and WPA.
13
Cloud Control
CLOUDCONTROL™ WEP
SETUP
Type in the Service Set
Identifier (SSID) this is
the name of your
wireless network.
Then select the Key text box
to enter your password if you
have one. Type it in using the
keyboard.
Now you will save the SSID &
password to the hot tub and
the tub will be ready to connect to your network.
The BWG Spa network will
now disconnect and you will
be controlling your tub via
your local/home network.
14
You may need to go to your
settings and connect to your
local / home network after you
save the password and restart
the app.
Exit the app and make sure you
are connected to your home
network.
Cloud Control
CONTROLS MENU
If you have your home
network setup to automatically
connect, the CloudControl app
will re-connect.
Restart the app and connect
to the tub which will now be
connected to your local / home
network.
You may need to manually
connect to your local/home
network.
You can now control your tub
anywhere you can connect to
your local / home network.
You should now be
connected to your
local/home network.
You can now turn on your
pumps & lights by pressing the
Controls button.
On Android™, use the
back/return key to return
to the main app screen.
15
Cloud Control
On iOS devices, you will see
a Back Button that you will
use for navigating between
screens.
16
You can now turn on your
pumps & lights by pressing the
Controls button.
The equipment for your tub will
automatically show up on this
screen. You can turn the devices
on/off by pressing the buttons.
If you want to control your
tub away from your local /
home network, make sure
you have an Internet connection on your device (3G / 4G /
Hotspot).
Start the app and press the
Connect button. Now you can
control your tube via
the Internet and can
control your tub via your
local/home network.
When connected via the Internet a small cloud icon will appear under the Controls button
letting you know that you are
remotely connected.
Operate your spa by going to
the Controls screen.
Cloud Control
Depending on your coverage
and data speed, the response
time for acknowledging a
device press may vary. You will
know the app is waiting by the
small spinning dots.
17
Helpful Tips
Here are some tips that will help you get your CloudControl app
installed and operational so you can…
Control your spa anytime, anywhere, anyplace…
Make sure the Wi-Fi Module was installed properly
Power off the tub. The tub must be powered off for the Wi-Fi module to
initialize properly.
Plug the Wi-Fi module into a spare panel jack within your Control System. If you do not have a spare panel jack, use the y-adaptor cable (#
25657). Remove the panel connector and replace it with the y-adaptor.
Then plug the panel & Wi-Fi module into the y-adaptor cable. Power the
tub back on.
Make sure the Wi-Fi Module can connect to your home network
Before you connect to your home network you must
be able to see your home network from your tub.
The easiest way to check if you can see your home network from
your tub is to try and connect to it with your smart device next to
the tub. Open a browser window and connect to the Internet (or
any other app that connects to the Internet).
While standing at your tub, if you can connect your smart device
to the Internet through your home network, then the tub CloudControl Wi-Fi module can connect to your home network too.
If you cannot connect to the Internet through your
home network, you may need to move your router
or add a repeater or some other signal booster so
you can see your network at your tub.
You can also try moving the Wi-Fi module to a different
spot where you do have coverage in your yard.
Or hang it on the outside of the tub instead of under the
skirt of the tub.
Once you can see your home network you are ready.
18
Some other things we have seen and learned during initial setup and some
ways for you to confirm things are working properly:
1. Make sure you have connected the new Wi-Fi module to the tub with the
power off. The Wi-Fi module talks to the spa upon power up to get the
spa configurations. If you did not do this, power down the spa and then
restart it.
2. Upon first startup, the Wi-Fi module is initialized and will show BWG_
SPAXXXX on your Android™ or iPhone® device. Once this
occurs, keep in mind that:
a. This is talking to the tub via direct connect and can reach about
65 feet or 20 meters.
b. You should now test all the functions of the app in this
mode to determine they are all operational.
We suggest you check the control functions via this mode 1st before going
on.
If you can control all the functions via this direct connect, you should now
be able to connect the spa to your local home network.
3. Go to the Settings, Advanced, Wi-Fi settings and connect to
your local home network.
a. M
ake sure you select the proper password & encryption
(Open, WEP, WPA)
b. If you don’t, it looks like the Wi-Fi module connects to the new network, but since the password is wrong it will not connect – you will
know this because in couple of minutes the BWG_SPAXXXX will show
back up in your Wi-Fi settings
4. Once you connect the app to the local Wi-Fi network, you should reconnect your phone to the same network using your phone settings.
You will now be able to control the tub from anywhere that you can connect to your local / home network.
Restart the app. You should be communicating to the spa via your local
network. Check to see if all the controls function as they did in direct connect mode.
If they do you are all set up.
Once connected to the local network, the Wi-Fi module will always look for
that network only.
Now you are ready to test the Internet cloud function. You can do this 1 of
2 ways –
1. Disconnect your device from the local Wi-Fi network that the spa is on.
2. Reconnect to another Wi-Fi hot spot (network like STARBUCKS®) that has
Internet access or via the device’s cellular data connection.
Restart the app and connect. Since you are not on the local network, the
app will attempt to connect via the Internet cloud.
a. If successful, you will see a little cloud and you should be able to
control the spa functions
b. D
epending on your connection speeds, it may take up to 5 seconds
for a function to acknowledge you pressed a device icon (i.e. If you
press the light icon, you should see little spinning dots while the app
talks via the Internet to the spa and
the spa sends back a message that it changed the light)
You will now be able to control the tub anywhere you can connect to the
Internet.
19
Frequently Asked Questions (FAQ)
Q. When I connect via the local home router with one (1) device, then I try to connect with another smart device at the same
time, the next device connects via the cloud. Why?
A. There is only one (1) local router port available for connection. So if you have more than one (1) device trying to connect via the
local router, the others connect via the cloud.
Q. Sometimes when trying to connect to the spa via local home router, I get connected via the cloud instead. Why?
A. This can happen when another device was already connected via the local router and did not disconnect. This seems to happen more often
with Android devices, but it can occur with iOS devices also. You should kill the app on the Android or iOS to make sure it drops the local connection properly; otherwise the local router connection is taken by the previous running version of the app. This is just how apps sit in the
background in Android devices. For iOS devices, make sure you are out of the app.
Q. I am able to connect to my new wifi module directly (same as the previous version) no problem. I then change the wifi settings to connect
to my home network, no problem. It then instructs me on my iPhone to connect to my home network to connect to my spa. This is where I
am running into trouble. Once I change back to my home network on my iPhone and try to connect to my spa it keeps telling me “connection
failed.” Why?
A. This maybe due to two different things:
1. You may have mistyped your password, SSID or set your encryption wrong. The CloudControl module tries to connect to the router using
the information you entered. It will keep trying for 3-5 minutes. If after that time it cannot connect, the CloudControl module will show
up again as networks on your Wi-Fi settings screen. If it does, repeat the process to connect to the router making sure you type the SSID
& password correctly and select the proper encryption (Open, WEP, WPA).
2. You do not have local Wi-Fi coverage or very weak signal from your wireless router at your tub. If you cannot connect to the internet using iPhone and your local wireless router, the CloudControl module cannot connect to your home router either. You will need to add a
repeater or network extender to make sure you have local Wi-Fi coverage at your tub.
If you like to read more FAQ please visit. www.balboawater.com/bwa-faq
20
Wireless Troubleshooting Issues
Check the wires and wireless network adapter
Checking that all your wires are plugged in at the router and from the plug is one of the first things you should do – provided of course
that you have access to them. Verify that the power cord is connected and that all the lights of the router and cable/DSL modem are on.
Low Signal Strength
There are a number of factors that can cause the signal of your access point to deteriorate and the performance of your network to fall under par.
Practically any appliance that operates on the same frequency level (2.4 GHz) as 802.11b or 802.11g can cause interference with your wireless network. Be sure to keep cordless phones, microwaves and other electrical equipment at least 1m away from the access point. This will ensure you get
the best signal from your router.
Installing a repeater for a performance boost
If you’re looking for a boost you can always choose to install a repeater. The job of a repeater is to receive the signal, regenerate it and rebroadcast it
therefore extending the range of your wireless network. This would sit somewhere between your Access Point and your
wireless client.
Positioning the wireless router
You’ll want to put your wireless router somewhere where it will receive the strongest signal with the least amount of interference.
For the best results, follow these tips:
• P
osition your wireless router in a central location. Place the router as close to the center of your home as possible to increase the strength of the
wireless signal throughout your home.
• P
osition the wireless router off of the floor and away from walls and metal objects, such as metal file cabinets. The fewer physical
obstructions between your computer and the router’s signal, the more likely that you’ll be using the router’s full signal strength.
• R
educe interference. 802.11g networking equipment uses a 2.4 gigahertz (GHz) radio frequency. This is the same frequency as most
microwaves and many cordless phones. If you turn on the microwave or get a call on a cordless phone, your wireless signal might be temporarily
interrupted. You can avoid most of these issues by using a cordless phone with a higher frequency, such as 5.8 GHz.
21
Wireless Troubleshooting Issues Continues
Know Your Wireless Security
SSID (Service Set Identifier)
All wireless devices in your network must specify a password or SSID. Our agents strongly recommend a unique, obscure
combination of letters and numbers that you can recall easily.
WEP Security (Wired Equivalent Privacy)
A security protocol for wireless networks designed to provide the same security as a wired network, WEP encrypts data as it’s
transmitted radio waves.
WPA Security (Wireless Protected Access)
A security protocol designed with stronger data encryption and user authentication, WPA is relatively new and more secure than WEP.
Here Are Some Reasons Why You Can’t Get A Signal From Your Router
1. Distance Between the Router and Connection Points
Solutions: The easiest solution would be to move the router to an area where it is unobstructed or move the devices closer to the router when in
use. However, it is also possible to increase the range of Wi-Fi signals with Wi - Fi boosters, Wi - Fi repeaters, or by upgrading the router antenna.
2. ISP Speed
Solutions: First, determine the speed of the ISP provider. If it’s not very fast, then it may be time to upgrade to a better plan or a
faster router. Also, it may be wise to give the ISP a call to see if any configurations have changed. If the problem is an unreliable ISP,
it may be time to switch companies.
3. Walls and Other Interference
Solutions. Moving the wireless router to a different area can definitely help prevent the signals from being blocked or interfered
with by walls or other devices. Additional signal boosters or repeaters can help extend the Wi-Fi range, but it may be better to look
at different Wi - Fi directional antennas to aim the router directly at devices, windows, thinner walls, or doors to allow the signal to move
through the home unencumbered.
22
Wireless Troubleshooting Issues Continues
4. Number of Devices Online
Solutions: If there are just too many people using the Internet at the same time, an additional Internet connection may be needed.
It’s also possible to limit the number of devices connected to the Internet at the same time. In many cases, there may be outsiders
accessing the router and slowing down speeds. A strong Wi-Fi password should be installed at all times.
5. Outdated Wireless Router
Solutions: Outdated routers simply need to be replaced with newer wireless routers that comply with current Wi-Fi standards.
Damaged routers can be repaired; however, in many cases, buying a new router will save the user time and effort.
23
CloudControl™ Prior Wi-Fi Module Support
The iOS® app version is backward compatible with prior WiFi modules and will continue to operate as it has.
The iPhone®, iOS®, iPod® touch and iPad® are a
registered trademarks of Apple Inc.
Prior Wi-Fi modules only support local direct
connections and cannot be linked into a home
network. They only work in the local proximity of
your backyard spa.
The iPhone®, iOS®, iPod® touch and iPad® are a
trademarks of Apple Inc., registered in the U.S. and other
countries.
The Android™ app is not compatible with prior Wi-Fi modules as it does not support adhoc connections.
bwa™, BALBOA WATER GROUP and the Stylized Balboa
Logo are registered trademarks or applications applied for
in the US Patent & Trademark Office. All Rights reserved. All
other product or service names are the property of their
respective owners
System Requirements
The bwa™ Wi-Fi Module supports all BP systems.
http://www.balboawatergroup.com/bwa
24
Trademark & Patent Notices
Android is a trademark of Google Inc.
Products are covered under one of more of the following US Patents: 5332944, 5361215, 5550753, 5559720,
5,883,459, 6282370, 6590188, 7030343, 7, 417, 834 B2 & Canadian Pat 2342614 plus others. Other patents both foreign
and domestic applied for and pending.
Regulatory Compliance Information
United States
Contains FCC ID: W7OMRF24WG0MAMB
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the
instructions, may cause
harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
To satisfy FCC RF Exposure requirements for mobile and base
station transmission devices, a separation distance
of 20 cm or more should be maintained between the
antenna of this device and persons during operation.
To ensure compliance, operation at closer than this
distance is not recommended. The antenna(s) used for this
transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canada
Contains IC: 7693A-24WG0MAMB
This device complies with Industry Canada license-exempt
RSS standard(s). Operation is subject to the following
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any
interference received, including interference that
may cause undesired operation of this device.
Le présent appareil est conforme aus CNR d’Industrie Canada
applicablaes aux appareils radio exempts de licence.
• Increase the separation between the equipment and receiver.
25
Regulatory Compliance Information
L’exploitation est autorisée aux deux conditions
suivantes: (1) l’appareil ne doit pas produire de brouillage, et (2)
l’utilsateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.
The product must be disposed of separately in
accordance with the local waste disposal legislation
in force.
Europe
Environmental ratings:
The MRF24WB0MA/MB module conforms to the emission standards below.
Humidity: Up to 85% non-condensing
Test standards ETSI EN 300 328 V1.7.1 (2006-010)
Storage temp.: -30˚C (-22˚F) to + 85˚C (185 ˚F)
• Maximum Transmit Power
Specifications are subject to change without prior
notification.
• Maximum EIRP Spectral Density
• Frequency Range
• Transmitter Spurious Emissions
• Receiver Spurious Emissions
The modules are fully compliant with:
• Radiated Emissions EN 55022
• Electrostatic Discharge EN 61000-4-2
• Radiated Immunity EN 61000-4-3
• EN 60950-1
• CE-Mark
• RoHS
26
Specifications
Operating temp.: -20˚C (-4˚F) to +60˚C (140˚F)
Intellectual Property Advisement
All Intellectual property, as defined below, owned by or which
is otherwise the property of Balboa Water Group or its respective suppliers relating to the Balboa Water Group BP Spa Control Systems, including but not limited to, accessories, parts, or
software relating to the “System”, is proprietary to Balboa Water
Group and protected under federal laws, state laws, and international treaty provisions. Intellectual Property includes, but is
not limited to, inventions (patentable or unpatentable), patents, trade secrets, copyrights, software, computer programs,
and related documentation, and other works of authorship.
You may not infringe or otherwise violate the rights secured
by the Intellectual Property. Moreover, you agree that you will
not (and will not attempt to) modify, prepare derivative works
of, reverse engineer, decompile, disassemble, or otherwise
attempt to create source code from the software. No title to or
ownership in the Intellectual Property is transferred to you. All
applicable rights of the Intellectual Property shall remain with
Balboa Water Group and its suppliers.
27
668 W 14600 S, Bluffdale, UT 84065
Phone: 801.307.3517
www.bullfrogspas.com
In Partnership with:
BALBOA WATER GROUP
w w w.balboawater.com
Corporate Office, Tustin, California
Electronic Manufacturing
1382 Bell Avenue
Tustin, California 92780
P 714.384.0384
F 714.384.0385
Valencia, California
Whirlpool Spa and Bath Manufacturing
28545 Livingston Avenue
Valencia, California 91355
P 714.384.0384
F 714.384.0385
Melbourne, Australia
Australian Sales Division
P 1.800 137 879
F 1.800 0703 233
Varde, Denmark
European Sales Division
Roustvej 50
DK-6800 Varde, Denmark
P +45.75.22.46.88
F +45.75.22.52.45
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement