Electronics Line iconnect User manual
PDF
Download
Document
Advertisement
Advertisement
SR L AD ID UR EG User Manual AR GS For quick installation information please refer to the iConnect Quick Start Installation Guide provided on our website: www.electronics-line.com Function Press… Additional Information ARM OR PART PERIMETER Hold down this key until “Instant Arming OK?” is displayed. Then Press √. [USER CODE] + FIRE ALARM + MEDICAL ALARM + MENU MODE then [USER CODE] CHECK TROUBLE CONDITIONS Use this key scroll the system trouble list AR GLOBAL CHIME RECORD MESSAGE ID UR Use the menu navigation keys (/) until the required menu item is displayed then press √. Alternatively, enter the shortcut (e.g. 21 for Bypass Zones). Pressing also silences any trouble tones that may be sounded by the system. then [HA/PGM UNIT #] then [HA/PGM UNIT #] GS SERVICE CALL Press these keys together and hold them down to generate an alarm. EG SWITCH HA/PGM UNIT OFF Instant arming cancels the entry delay after Part or Perimeter arming. This feature can be enabled by your installer. Entering your user code also silences the siren in the event of an alarm. PANIC ALARM SWITCH HA/PGM UNIT ON The default Master code is 1234. AD DISARM If One-Key Arming is disabled on the Control System, enter your user code when arming. OR FULL INSTANT ARM SR L Quick Reference Guide Enter the HA module number in two digits (e.g. 03, or 30/31 for PGM). Hold down this key until “Service Call Dialing” is displayed. The number dialed for the service call is programmed by your installer. then Use the menu navigation keys (/) to choose enable or disable, then press √. then After recording a message, “Message Waiting” is displayed until the message is played back. PLAY MESSAGE Press… Additional Information then The Message Center is an optional feature that is included with certain versions Control of iConnect System. Telecontrol Commands Function Function DISARM FULL ARM SIREN CANCEL HA/PGM UNIT XX ON* then HA/PGM UNIT XX OFF* then EXTEND CALL DISCONNECT for PGM XX=30/31 UR EG GS AR Press… AD 2-WAY AUDIO ID * Press… SR L Function -3- then SR L Table of Contents Quick Reference Guide ..................................................................................................................... 2 Table of Contents .............................................................................................................................. 4 Introduction and Overview ...................................................................................................... 6 1.1. Documentation Conventions .............................................................................................. 6 1.2. Security System Components ............................................................................................ 7 1.3. System Monitoring ............................................................................................................. 8 1.4. Home Automation .............................................................................................................. 8 1.5. Self-Monitoring ................................................................................................................... 8 1.6. Telecontrol ......................................................................................................................... 8 1.7. Vocal Message Annunciation ............................................................................................. 9 1.8. Web Access ....................................................................................................................... 9 2. The User Interface .................................................................................................................. 10 2.1. Front Panel ...................................................................................................................... 10 2.2. Alarm Sounding Patterns ................................................................................................. 12 2.3. Keyfobs ............................................................................................................................ 12 2.4. Wireless Keypads ............................................................................................................ 12 3. Arming and Disarming ........................................................................................................... 15 3.1. Arming Modes .................................................................................................................. 15 3.2. Arming the System ........................................................................................................... 15 3.3. Disarming the System ...................................................................................................... 17 3.4. Arm Status Indication and Other System Status Indication .............................................. 17 3.5. Arming and System Tones ............................................................................................... 18 3.6. Remote Arming and Disarming ........................................................................................ 19 4. Web User Application ............................................................................................................ 21 4.1. Logging In ........................................................................................................................ 21 4.2. The Main Page ................................................................................................................. 22 4.3. Arming and Disarming via the Web Application................................................................ 23 4.4. Web Application Settings ................................................................................................. 24 4.5. Event Log History ............................................................................................................. 28 4.6. Home Automation ............................................................................................................ 28 4.7. Video Verification ............................................................................................................. 28 5. Panic Alarms .......................................................................................................................... 29 5.1. Keypad Alarms ................................................................................................................. 29 5.2. Keyfob Panic Alarm.......................................................................................................... 29 5.3. Medical/Panic Alarm ........................................................................................................ 29 6. Home Automation and PGM .................................................................................................. 30 6.1. Keypad Control ................................................................................................................ 30 6.2. Keyfob Control ................................................................................................................. 30 6.3. Telephone Control ............................................................................................................ 31 6.4. SMS Control ..................................................................................................................... 31 6.5. Scheduling (not relevant to PGM)..................................................................................... 32 7. Telecontrol .............................................................................................................................. 33 7.1. Calling your Home............................................................................................................ 33 7.2. Service Call ...................................................................................................................... 35 7.3. Two-Way Audio after an Alarm ........................................................................................ 35 7.4. Two-Way Audio Follow-Me............................................................................................... 35 7.5. Simplex Mode .................................................................................................................. 35 AR GS EG UR ID AD 1. -4- Advanced System Operation ................................................................................................. 36 8.1. Cancel Report .................................................................................................................. 37 8.2. Zone Bypassing/Unbypassing .......................................................................................... 37 8.3. User Codes ...................................................................................................................... 37 8.4. Follow-Me ........................................................................................................................ 40 8.5. Event Log ......................................................................................................................... 40 8.6. Service Menu ................................................................................................................... 41 SR L 8. Appendix A: Menu Structure ........................................................................................................... 47 AR GS EG UR ID AD Appendix B: Glossary...................................................................................................................... 48 -5- Introduction and Overview SR L 1. 1.1. AD This user manual explains all you need to know about your iConnect security system and provides step-by-step instructions for all the system’s user functions. In addition to the explanation you will receive from your installer, we urge you to read this manual so that you can take full advantage of your system’s features. Keep this manual in an accessible location for future reference. system has many features in order to suit a wide range of applications. The iConnect This manual outlines all of these features but it is likely that there are options that are not relevant to your system. If you have any questions regarding the availability of the features described in the manual, please ask your installer. Documentation Conventions In order to simplify the procedures that appear in the rest of this manual, the following conventions are used: Description… Use the arrow buttons to scroll through the options and press √. From the Event Log Menu, select Clear Log. Enter the main menu by pressing √ and entering your user code. Using the arrow buttons, navigate until you reach Event Log and press √. Using the arrow buttons, navigate until you reach Clear Log and press √. [#5] The same as above only this time you are navigating through three menu levels. The shortcut to a specific menu item from the main menu. In this case, this is the shortcut for Set Date. These appear in the procedures as an additional aid to menu navigation. EG [7012] UR From the Service menu, select Set Time/Date, Set Date. ID Item… Select… A shortcut to a specific item in a sub-menu. For example, [#5] is the shortcut to Bell enable disable in the submenu that is opened once you have selected the detector you want to program. GS √ , buttons AR 5. Interface Test Indicate buttons that appear on the keypad ( , ) The text that actually appears on the LCD display (italics). Note Important caution, please pay attention. -6- 1.2. Security System Components SR L Your security system is made up of a Control System, various detectors and a number of optional peripheral devices. This section explains the role of each component in your system. Control System AD The Control System is the brain of the system. It communicates with all the devices connected to the system. For example, in the event of a burglary, a detector sends a signal to the Control System indicating that it has sensed motion on the premises. On receiving this signal, the Control System makes the decision to report the alarm to your monitoring service and activate the siren. Detectors Keyfobs UR ID Detectors are the devices that protect your home, alerting the Control System when there is a breach in security. Magnetic contacts protect your doors and windows while motion detectors with built-in video modules are able to detect an intruder moving across its field of view and snap an image as proof of intrusion. Additionally, smoke, carbon monoxide, gas leak and flood detectors can be installed to provide an early warning in the event of a fire, the presence of dangerous gases or the potential for flooding. EG Keyfobs are hand-held transmitters that are used to operate the system. Various keyfobs are available providing a number of functions. For example, arming/disarming the system, sending medical and panic alarms and various home automation functions. Keypads GS The keypads enable you to communicate with the Control System in order to perform a number of different functions. The main function you can perform using a keypad is to arm the system when leaving your home and to disarm on your return. AR Sirens and Strobes While the Control System includes a built-in internal siren, it is possible that you also have an external siren and strobes installed. The sirens are sounded and the strobes are activated during certain alarm conditions serving to warn you and ward off intruders. -7- System Monitoring SR L 1.3. AD When an event occurs within the system, the Control System sends a message to your monitoring service describing the exact nature of the event. This enables the monitoring service to take the required action. System monitoring can implement either regular telephone or cellular communication. A detector detects. The Control System is alerted. An alarm is generated and the monitoring service is notified. 1.4. Home Automation ID Remember that no security system can prevent emergencies. This system is only intended to alert you in case of an emergency and should not take the place of prudent security practices or life and property insurance. 1.5. UR An optional expansion module can provide you with the ability to control up to 16 individual electrical appliances or lights using the front panel keypad, wireless keypads or keyfobs. Additionally, each appliance can be programmed to be turned on and off automatically according to various schedules and system status conditions. Self-Monitoring 1.6. EG In addition to the ability to report to a monitoring service, the system can also send you and other users notification when an event occurs. This may be in the form of vocal messages played over the telephone or, if your system supports cellular communication, you can receive information on system status via SMS. If an alarm occurs on the premises, you are informed no matter where you are in the world. Telecontrol AR GS The iConnect offers a range of “Telecontrol” features that provide remote access via the telephone. These features include remote arming/disarming, HA on/off, PGM output activation/deactivation, siren cancel and Two-Way audio via the Control System’s builtin microphone and speaker -- see Telecontrol. The Two-Way Audio features allow you to contact your home directly in the event of an alarm or simply to check the premises when you are away. Using your cellular phone, you can also send commands to the appliances controlled by the Home Automation feature using SMS and receive confirmation when the command is received. -8- 1.7. Vocal Message Annunciation 1.8. SR L Vocal message annunciation is an optional feature that, if enabled in programming, causes the system to play short messages that indicate system status. Web Access AR GS EG UR ID AD The Web Application provides an interface to your security system from your Internet browser. Via the Web you can perform a wide range of tasks such as arm/disarm, zone bypass, user code management and home automation control. Additionally, you can set up the contacts whom you wish to be alerted (by email or text message) when selected events occur. The application also allows you to check your home at any time either by viewing a history of recent events that have occurred or by viewing streaming video from cameras installed on the premises. For further information, see Web User Application -9- The User Interface SR L 2. 2.1. AD There are several methods you can use to operate the system. Apart from the keypad on the front panel, your system may include a number of peripheral devices such as keypads and keyfobs. This chapter provides a brief introduction to each of the devices you can use to operate the system. It is important that you familiarize yourself with these devices before reading the following chapters that shall describe system operation in further detail. The front panel is the main user interface that provides you with all the functions you Control System is available with the need to control your security system. iConnect LCD front panel configuration. Front Panel ID LCD Front Panel display and LEDs inform you of system arming status, power failures, and system trouble conditions. Its alphanumeric keypad enables you to enter your user code when arming and disarming, and to silence the siren in the event of an alarm. UR LCD Display Alphanumeric Keypad GS Home Automation/ PGM Keys Menu Navigation Keys EG Arming Keys System Status indicators Arming Keys AR Three arming keys are available: Full, Part, and Perimeter. These keys arm the system using one of the three arming methods. One-key Arming is an option that is programmed by your installer. If this option is disabled, you must also enter a user code when arming. -10- Service Call Button SR L The Service Call button enables you to contact the monitoring service and talk to an operator. To initiate a service call, press and hold down the Service Call key seconds. Vocal Message Recording and Playback for a few LCD front panel allows you to record a short message that may be played back later by another user -- see Service Menu, Message Center. AD PGM and Home Automation On/Off Keys Pressing one of the Home Automation keys ( ON, OFF) followed by the unit number (01-16, or 30, 31 for PGM) enables you to control lights and appliances in your home, activate and deactivate the PGM output. System Status LEDs ID Pressing both Home Automation keys simultaneously generates an SOS panic alarm. The System Status indicators provide essential information on the status of the system such as arm, disarm, alarm and power failure conditions. It means… UR If the OK LED is… Off Both AC and Battery power are disconnected. On – Green System Power status is OK and there is no System Trouble. On – Yellow Open Zone. Check that the windows and doors are closed and no movement is detected by the detectors within the protected area). System Trouble. EG Flashing Green Battery low from the Control System or transmitters. Flashing Yellow (fast) AC loss. Intermittent On/Off – Yellow System Trouble in addition to AC loss/Low Battery. GS Flashing Yellow (slow) If the Arm Status LED is… Off It means… The system is disarmed. The system is armed. Flashing Red An alarm has occurred. Alarm indication is cleared the next time you arm the system or view the relevant event in the event log. AR On – Green Alarm indication is not displayed after a silent panic alarm. -11- System Trouble Indication 2.2. SR L In the event that the system detects a trouble condition, “System Trouble” appears on the display. To identify the problem, scroll through the trouble list by pressing. Scrolling the trouble list also silences system trouble tones that may be sounded if enabled in programming. When the trouble condition is restored, it is removed from the system trouble list. For detailed information on system messages, see Arm Status Indication and ¡Error! No se encuentra el origen de la referencia.. Alarm Sounding Patterns The following table summarizes various alarms sounded by the control system. Alarm Sounding Pattern Description ON (continuously) Fire ON - ON - ON, 1.5-second pause, ON - ON – ON...... Gas ON - ON - ON - ON (short bursts), 5 second pause, ON - ON - ON ON...... AD Alarm Burglary ON (continuously) – only applicable for Medical alarm from zone Flood 4 rapid tones sounded once per minute (same as Trouble tones) Environmental 4 rapid tones sounded once per minute (same as Trouble tones) Keyfobs UR 2.3. ID Medical The iConnect supports two types of keyfob transmitter (EL-4714, EL-4711M/P). The functions of the buttons on each keyfob are shown below. Full Arm EG Disarm EL-4711M/P EL-4714 2.4. Medical/Panic Emergency Part Arm or Home Automation/PGM GS Perimeter Arm or Home Automation/PGM Wireless Keypads AR The system supports up to four Wireless Keypads. The Wireless Keypad (EL-4727) is an intelligent two-way wireless keypad with LCD display. Apart from serving as an additional arming station, the Wireless Keypad provides memo recording options, control over up to 16 home automation devices, and panic alarm function. You can arm and disarm the system using the Smartkey (if supported). -12- AD SR L 1. Speaker 2. LCD Display 3. Arming Keys 4. Keypad 5. Microphone (optional) 6. System Status LEDs ID EL-4727 Numeric Keypad UR The numeric keypad allows you to arm or disarm the system by entering a user code. Arming Keys Panic Alarm EG Three arming keys (Full, Part and Perimeter) allow you to arm the system using one of the three arming methods – see Arming and Disarming. One-key Arming is an option that is programmed by your installer. If this option is disabled, you must also enter a user code when arming. Simultaneously pressing the Full and Perimeter buttons generates a panic alarm. PGM/Home Automation On/Off Keys GS Pressing one of the Home Automation keys followed by the unit number (01-16) enables you to control lights and appliances in your home. To generate a panic alarm, press both Home Automation keys simultaneously and hold them down Cancel AR The Cancel key clears the keypad in the event that you pressed a key by mistake. For example, when entering your code you enter a wrong digit; the system waits for you to enter all four digits before it decides that the code is incorrect. Pressing the Cancel key causes the keypad to disregard what was previously entered enabling you to start again. -13- LEDs ) indicate arming and power status of the system: SR L Two status LEDs (OK and If the OK LED is… It means… Off The system is disconnected from all power sources. On - Green The keypad is powered by AC and the battery is not low. Flashing Yellow (slow) Local backup battery low. Flashing Yellow (fast) Wireless Keypad AC loss. If the It means… LED is… The system is disarmed. On - Green The system is armed. Flashing Red An alarm has occurred. This alarm indication is reset when the system is armed using any of the three arming methods. AD Off AR GS EG UR ID Alarm indication is not displayed after a silent panic alarm. -14- Arming and Disarming SR L 3. Arming can be defined as activating the system. When the system is armed, it monitors the zones that are protected by the detectors. If a detector detects an intrusion, the system generates an alarm. 3.1. Arming Modes Perimeter Arming Perimeter arming enables you to activate the perimeter zones (the windows and doors of your home) enabling you to move freely within the protected area. ID Part Arming Part arming enables you to arm a section of your home while remaining on a different part of the premises. UR Full Arming Full arming activates the entire system. This arming method is used when you intend to leave your home, leaving the premises empty. AD Three arming modes are available: Full, Part and Perimeter. These modes enable you to arm your system accordingly to suit different circumstances. Certain detectors, such as smoke, carbon monoxide, gas and flood detectors, are always active regardless of system status. Arming the System EG 3.2. Before arming the system, check that all doors and windows are secured so that the system is ready for arming. If the One-key Arming option is disabled in programming, you must enter your user code when arming the system from a keypad. GS Arming with the Front Panel or Wireless Keypad To arm the system using the front panel or Wireless Keypad: Press one of the three arming keys; the exit delay begins to count down. At the end of the exit delay, the system is armed. If the One-key Arming option is disabled in programming, you must enter your user code when arming the system from a Wireless Keypad, or place a registered smartkey (if supported) against the center of the smartkey reader. AR • -15- Arming with the Keyfob • SR L To arm the system using the keyfob: Press the relevant button on your keyfob (see Keyfobs); the exit delay begins to count down. At the end of the exit delay, the system is armed. Forced Arming AD Forced arming enables you to arm when the system is not ready. For example, if a door protected by a magnetic contact is open, you may arm the system on condition that the door will be closed by the end of the Exit delay. If the door is still open after the exit delay expires, an alarm is generated. Forced arming is available only if the option is enabled in programming. Forced arming may be enabled for specific zones or for the entire system. Instant Arming ID Instant arming is a feature that allows you to cancel the entry delay after Part or Perimeter arming the system. For this feature to function, it must be enabled in programming by your installer. Supervised Arm UR To instantly arm the system. 1. Check if the system is ready to arm. 2. Press the Part or Perimeter arming key on the keypad and enter your user code if One-Key Arming is disabled. 3. Press and hold down on your keypad until the message Instant Arming, OK? is displayed 4. Press √; the entry delay for the current arming period is canceled. EG Supervised Arm is an optional feature designed to supervise intrusion detector activity before you arm the system. If supervised arm is enabled in programming and the system has not received a transmission from a detector for a certain amount of time, all arming methods that include that detector shall not be available. GS In this case, press to check which detector is causing the “System Not Ready” condition. AR To make the required arming method available, activate the detector. If activating the detector does not help, there may be a problem with the detector. You can bypass the faulty detector’s zone to allow system arming until the problem is remedied – see Zone Bypassing/Unbypassing. -16- 3.3. Disarming the System SR L When you enter the premises, the entry delay begins to count down. You must disarm the system within the entry delay time to prevent the system from triggering an alarm. To disarm the system using a keypad: Enter your user code. • To disarm the system using a keyfob: To disarm the System using a Smartkey (if supported): AD Press the disarm button – see Keyfobs • Place a registered smartkey against the center of the smartkey reader of the Wireless Keypad. When the smartkey is read, the keypad will sound a beep – the system is disarmed. 3.4. Arm Status Indication and Other System Status Indication ID • UR The system’s arm status is displayed on the front panel only. The following table explains the various arm status descriptions that appear on the LCD display. Status Means… DISARMED The system is disarmed. FULL ARMED PERIMETER ARMED FULL ARMING PART ARMING The system is in the process of arming (displayed during exit delay). GS PERIMETER ARMING The system has been armed using the displayed arming method. EG PART ARMED DISARMED 12:22:11 PART ARMED INST PERIM ARMED INST PART ARMING INST AR PERI ARMING INST The system has been armed using the displayed arming method with the Instant arm feature activated. The system is in the process of arming with the Instant arm feature activated. The system may be programmed to display arm status at all times or only for the first two minutes or 30 seconds after you arm or disarm the system according to the system's configuration as programmed by the installer. -17- Status Means… ZONES IN ALARM Zones have been violated. SR L In addition to arm status, the system displays further status messages on the front panel’s display. The following table explains common status indication messages that may prevent you from arming your system. The system has been tampered with. SYSTEM NOT READY The system is not ready to arm, check that all doors and windows are closed. KEYPAD LOCKED Five unsuccessful attempts were made to enter a user code; the keypad is locked for 30 minutes. If this message appears, it is still possible to arm/disarm the system using a keyfob. Arming is possible using a keypad if one key arming is enabled. SYSTEM TROUBLE A trouble condition has been detected, press for further details. 3.5. Arming and System Tones FULL ARMING 7 TO EXIT ID System tones are the chimes that the system sounds to indicate entry/exit delay, arming and disarming, system troubles and so on. Various options are available that determine the pattern of these tones. AD TAMPER ALARM UR System tones may be sounded by either the external wireless siren or the Control System’s built-in siren. The following table is a summary of the tones sounded by the control system. Tones Exit Delay/ Entry Delay 4 tones or continuous tones. The exit/entry delay is counting down. The tones quicken when there are 13 seconds remaining and quicken again when there are 5 seconds remaining. The number of tones sounded during each delay is programmed by your installer. Chime 2-tone sequence (similar to a doorbell – high to low). A detector that has been programmed to chime by your installer has been activated – see Service Menu, Global Chime. AR Disarm GS Arm Description EG Status Home Automation 3-tone sequence (low to high) sounded twice The system has been armed using any of the arming methods. Arm tones are optional and are programmed by the installer. 3-tone sequence (high to low). The system has been disarmed. Disarm tones are optional and are programmed by the installer. Rapid 2-tone sequence An automated device has been turned On or Off using a wireless keypad or keyfob. This audible indication is programmed by your installer. -18- Tones Description System Trouble 4 rapid tones sounded once per minute. A trouble condition has been detected, press for further details. For Fire Trouble Tones, there is a programmable option to repeat the tones every 3½ hours until the problem has been taken care of. Note: System trouble tones are not sounded from 10:00pm to 7:00am 3.6. SR L Status Remote Arming and Disarming Remote Arming/Disarming via SMS AD You can arm and disarm the system remotely by sending the SMS commands from a cellular phone to the cellular communications module. Each SMS command contains the following elements: SMS Command Descriptor (up to 43 characters of free text) # (separates the descriptor from the actual command) User Code Command (120=Disarm, 121=Full Arm, 122=Part Arm, 123=Perimeter Arm, 124=Full + Perimeter Arm, 125=Part + Perimeter Arm, 200 = Arm Status) ID • • • • UR The following example shows the format of an SMS command for disarming the system: SMS Command Descriptor D I S A R User Code M # 1 2 3 Command 4 1 2 0 Arm Status Reply EG While the SMS Command Descriptor is optional, you must start the SMS command with the # symbol for the system to accept the command. On receiving an Arm Status request message, the system returns a status message to the sender. This message includes the system status and the descriptor of the user or the device used to arm/disarm the system. GS The following example shows an Arm Status reply where the system has been fully armed by a user named Mark. F U L L A R M E D - M A R K SMS Confirmation Message AR After an SMS command is executed by the system, if programmed by your installer, a confirmation message may be returned to your mobile phone. The following example shows the confirmation message you receive for the sample command from the previous section. D I S A R M E -19- D Remote Arming/Disarming via the Telephone Remote Arming/Disarming via WUAPP and WAP SR L Using the Telecontrol feature, you can “Full” arm and disarm the system via the telephone. For further information on the Telecontrol features, see Telecontrol. AR GS EG UR ID AD You can arm and disarm the system remotely using the WUAPP (Web User Application) and WAP – see Web User Application. -20- Web User Application SR L 4. The Web User Application provides a full interface to your system from a local or remote PC. Via the Web you can perform a wide range of tasks such as arm/disarm, zone bypass, user code management and home automation control. You can also access the Web User Application from your cellular phone or PDA using the WAP portal. 4.1. Logging In UR ID AD This application is usually part of the service provider’s Web site and requires the end user to log in to gain access to the page. To enter the Web Application, on your browser enter the Web page address supplied by your WEB service provider and press Go. You will see the Login Page. EG To login to the Web Application, enter your user name and password supplied by your WEB service provider, and the pass code which is your User Code, then click the Enter button. AR GS For your system security reasons, you must change the password immediately at first login. You can change your password on the Change Password page that is accessible from the Settings menu. Your new password should be no less than six characters and must start with a letter. -21- 4.2. The Main Page Home Menu Bar AD Workspace SR L After logging in, your system’s home page is displayed. The following diagram shows the home page and explains the main elements of the web application’s interface. ID Status Bar Menu Bar EG UR When using the Smartphone application service, the main page looks the following way: GS The Menu Bar includes the Main Menu; arm/disarm options list and the Log Off button. The Main Menu offers links to various pages in the Web Application. Use the Logoff button on the right side menu to properly close the session. The following options are available from the Main Menu: Home – pressing the Home button allows the user to return to the Main page at any time • Settings – offers various options including user code and contact management, event log viewing and zone bypass. • • History – enables you to view the system’s event log AR • Video – provides access to view streaming video from IP cameras -22- Automation – allows you to control and schedule automated lights and appliances in your home • Help – offers online explanations on how to use the Web Application plus FAQ and customer support options. SR L • Status Bar AD The Status bar displays information on your system’s status and the name of the user currently logged in. Above the status bar, the time when the system status display was last updated is shown. This information is displayed according to the local time at the control system. When logging into the WUApp with a GPRS Control System, the system status refreshes automatically, and can be refreshed manually as well. To refresh the current system status, click the Refresh Status button on the right-hand side of the Status bar. Workspace ID The workspace offers additional links to the following pages of the application: Users and Codes, History, Alerts, Change Password, Video. When you choose a page, either from the Main Menu, or from the workspace, the page is displayed in the workspace. For example, if you choose Arm/Disarm from the Main Menu, System Operation area and System Status area are displayed in the workspace (see the figure below). Home Button Arming and Disarming via the Web Application GS EG 4.3. UR On the main menu, there is Home button. Press the Home button to return to the Main page at any time. AR You can arm and disarm the system using the Arm/Disarm drop-down box (upper-right part of the page) or using the buttons in the System Operation Area. It is important to note that when you are using the Web application, the system is armed with the programmed delay. -23- The Web Application allows you to arm and disarm your system via the Web Application using any of the available arming methods: • On the Status Bar below on the page you can see the current status of the system (in our example it is Disarmed and System Ready, which means that the system and all the detectors are working properly and there are no events to report). It is possible to check if there were alarms in the system. 4.4. SR L • Web Application Settings UR ID AD System Users and Codes AR GS EG In this area you can add, delete, or change users and the User Codes for your system (for example, add codes for family members). 1. On The Main Page menu, click Settings. 2. Click System Users and Codes, the following page appears: -24- Web Interface Users and Codes SR L The Web Interface Users and Codes page provides a useful tool for managing your system’s users. From this page you can add, edit and delete users as required. You can even issue temporary (limited) codes to guests that will expire after 24 hours. ID AD On The Main Page menu, click Settings, then Web Interface Users and Codes, the following page appears: Change Password AR GS EG UR Click Settings then Change Password to change the password you use to login to the Web Application. -25- Zone Bypass AD SR L On The Main Page menu, click Settings then Zone Bypass to bypass certain zones in your home that you don't want to receive event messages from. Select the checkboxes for the zones you want to bypass. ID Change Appearance AR GS EG UR On The Main Page menu, click Settings then Change Appearance to change the color scheme of your account. -26- Alerts ID AD SR L The Alerts page allows you to enter the details of contacts you wish to be informed when events occur in your system. For example, you can enter your own email address and/or cellular phone number so that you will receive email or SMS notification in the event of an alarm. 1. On The Main Page menu, click the Alerts area. The following page appears: Press Add new to add email addresses or cellular telephone numbers for the alert messages 3. 4. 5. 6. In the Contact Name field, enter the name of the contact to receive alerts. In the Email Address field, enter the email address for email alerts. In the Cellular Phone # field, enter the cellular phone number for SMS alerts. To start receiving the events messages, in the area below, select the checkboxes according to the event type and message type you prefer (email or SMS). Test the alerts you have programmed by clicking the Test button on the Alerts page near the newly added alert. GS AR 7. EG UR 2. -27- 4.5. Event Log History SR L The History page enables you to view the system’s event log. The events are arranged in a table that offers the advantage of allowing you to view a large number of events at once. In addition to viewing the event log, you may also save the log to a file (HTML, PDF or RTF) or print the log. For further details on how to use the Web Application, refer to the Help menu included in the application. To view the system’s event log: On The Main Page menu, click History, the following page appears: 4.6. UR ID AD • Home Automation EG The Web Application allows you to control and schedule automated lights and appliances in your home. The application offers a comprehensive interface that enables you to view the settings for all of your automated devices at once. Additionally, you can add, edit or delete devices from the comfort of your PC. Discuss this capability with your security service provider to determine if it is applicable to your system. Video Verification GS 4.7. Using the 2-way wireless video verification PIR detectors installed in your home, the Web Application enables you to view live video images over the Web in order to check your home and family while you are away. AR Discuss this capability with your security service provider to determine if it is applicable to your system. -28- Panic Alarms SR L 5. Panic alarms enable you to send a message to the monitoring service in the event of an emergency. There are various types of panic alarm and several methods you can use to generate them. 5.1. Keypad Alarms To activate an SOS Panic alarm from the front panel or wireless LDC keypad: Press and hold down the Home Automation On and Off keys simultaneously AD • • Press and hold down keys 1 and 3 simultaneously. ID To activate a Fire alarm from the front panel keypad or wireless LCD keypad: To activate a Medical alarm from the front panel keypad or wireless LCD keypad: 5.2. Press and hold down keys 4 and 6 simultaneously. UR • Keyfob Panic Alarm • Press the lower two buttons simultaneously Medical/Panic Alarm GS 5.3. EG To activate a Panic alarm using the four-button keyfob (EL-4717): The one-button keyfob (EL-4711M/P) is designed to send a message to your monitoring service in the event of a medical or panic emergency. AR The transmitter is water-resistant and can be worn around the neck as a pendant. -29- Home Automation and PGM SR L 6. Home Automation is an optional feature that requires an add-on expansion module. Home Automation enables you to control up to 16 individual lights and appliances around the home, in this section; we shall refer to these lights and appliances as HA units and PGM output. The PGM is a programmable output that is triggered according to specific system status conditions, or by remote command sent via PSTN, GSM, Ethernet, keyfob, keypad, or Remote Programmer. AD HA units and the PGM programmable output can be controlled (using the keypad and keyfobs, remotely by telephone or SMS) or programmed to react to specific system status conditions. For example, an HA unit can be programmed to switch on when the system is armed or when a specific zone is triggered. Additionally, the Randomize feature is designed to switch lights on and off at night when the system is armed. This gives potential intruders the impression that the house is occupied. 6.1. ID Scheduling options enable you to program On and Off times for each HA unit. This feature is found in the main menu. For further information on how to navigate the menu, refer to Advanced System Operation. Keypad Control UR Two keys on the keypad enable you to send On and Off commands to HA units, activate and deactivate the PGM output. How HA/PGM units react to the On command is determined by the installer in programming. The HA/PGM unit can be programmed to switch on until the Off command is received or automatically switch itself off after a pre-programmed amount of time. To turn HA/PGM units on using the keypad: . Press the On key Enter the two-digit HA/PGM unit number (01-16, or 30, 31 for PGM); the chosen HA/PGM unit switches on. EG 1. 2. To turn HA/PGM units on using the keypad: 6.2. Press the Off key . Enter the two-digit HA/PGM unit number (01-16, or 30, 31 for PGM); the chosen HA/PGM unit switches off. GS 1. 2. Keyfob Control AR You can control two separate HA units, using the four-button keyfob. This option can be programmed by the installer. For further information on keyfob button assignments refer to Keyfobs. -30- 6.3. Telephone Control 6.4. SR L Using the Telecontrol feature, you can control HA units and PGM output remotely via the telephone. For further information on the Telecontrol features, see Telecontrol. SMS Control If your system supports cellular communication, you can control HA units and PGM remotely via your mobile phone using a number of SMS commands. The SMS commands are designed to be entered as templates on your mobile phone. Each SMS command contains the following elements: AD SMS Command Descriptor (up to 43 characters long) # (separates the descriptor from the actual command) User Code Command (0=Off, 1=On) HA Unit Number (01-16, or 30, 31 for PGM) ID • • • • • The following example shows the format of an SMS command to switch on a water boiler controlled by HA unit 08. SMS Command Descriptor O I L E R User Code O N # 1 2 3 UR B On 4 1 Unit 0 8 Do not include the symbol ‘#’ in the descriptor as the system regards any text after this symbol as part of the command. The SMS Command Descriptor is optional but you must still enter the ‘#’ before the user code. SMS Confirmation Message Format EG After an SMS command is executed by the system, if programmed by your installer, a confirmation message may be returned to your mobile phone. This message includes the HA unit’s descriptor and the command that was sent. The following example shows the confirmation message you receive for the sample command from the previous section. O I L E AR GS B -31- R - O N 6.5. Scheduling (not relevant to PGM) SR L The Scheduling feature allows you to set an On and Off time for each HA unit. At these times the system automatically switches the HA unit on and off. You can also choose the days of the week that the schedule is active. On Time AD To edit an HA unit’s “On” Time: 1. From the main menu, select HA Schedules [8]. 2. Select an HA unit. 3. From the HA unit’s sub-menu, select On Time. 4. Enter a time (HH:MM). 5. Press √ when the desired setting is displayed. Off Time ID To edit an HA unit’s “Off” Time: 1. From the main menu, select HA Schedules [8]. 2. Select an HA unit. 3. From the HA unit’s sub-menu, select Off Time. 4. Enter a time (HH:MM). 5. Press √ when the desired setting is displayed. UR Weekly Schedule Press… 1 2 3 Press… To toggle… Sunday 5 Thursday Monday 6 Friday Tuesday 7 Saturday Wednesday Press √ when the desired setting is displayed. AR 5. To toggle… GS 4 EG To program the days of the week that the schedule is active: 1. From the main menu, select HA Schedules [8]. 2. Select an HA unit. 3. From the HA unit’s sub-menu, select Schedule. 4. Use keys 1 to 7 to toggle the days on and off. -32- Telecontrol SR L 7. The iConnect Control System offers a range of Telecontrol features that provide remote access via the telephone. These features include Two-Way Audio, remote arming/disarming and siren cancel. Two-Way Audio 7.1. AD You may use the Two-Way Audio features to check your home in the event of an alarm or as an alternative means of communicating with members of your family. For example, you may wish to call an elderly person who has difficulty reaching the phone. Using its Two-Way Audio features, the Control System automatically picks up the call and you can communicate via its built-in microphone and speaker. Calling your Home ID You may call your home at any time in order to contact your family, operate your system or check your home while you are away. This feature is available for either regular telephone communication or cellular communication. Making a Call using a Regular Telephone UR When your security system shares a telephone line with other devices (e.g. telephone handsets, an answering machine or fax), it is important that the Control System distinguish between calls so that it knows when to pick up the relevant call. For this purpose the iConnect employs a double call method. EG To make a call to the Control System using the double call method: 1. Dial your telephone number. 2. Wait for two or three rings then hang-up. 3. Wait at least five seconds and dial the number again; on the second ring, the Control System picks up and sounds two tones. Making a Cellular Call to the System AR GS If your system supports cellular communication, it has its own individual telephone number. Therefore, the double call method is not necessary and you may call the Control System directly. -33- Call Procedure SR L To prevent unauthorized attempts to call your Control System, you must enter a user code when calling your home – see User Codes, Code 29. To call your home: 1. Call the Control System either using the double call method or directly (see above); when the Control System picks up, two tones are sounded. 2. Enter the Telecontrol code (Code 29) on your telephone within 15 seconds. Do not enter your user code until you hear the two tones. Any digits entered before the tones are sounded are disregarded by the system. A tone is sounded to indicate that the system is ready to receive commands. The following commands are available: • Press “2” for Two-Way Audio. AD 3. If the TWA mode is defined as “Simplex” (see Simplex Mode), the audio channel opens in Listen mode (microphone active/speaker mute). To switch to speak mode, press “1” on your telephone. To switch back to Listen mode, press “0” on your telephone. ID During the TWA session, you can adjust the speaker volume using the arrow buttons. Press “3” to fully arm the system. • Press "4XX" to turn HA unit #XX ON. • Press "430" to activate PGM output (Unit 30, 31) • Press "5XX" to turn HA unit #XX OFF. • Press "530" to deactivate PGM output (Unit 30, 31) UR • • Press “6” to disarm the system. • Press “9” to cancel the siren. 5. The duration of the call is an option programmed by your installer. Ten seconds before the end of the call, two short tones are sounded. To extend the call, press “7” on your telephone. To disconnect before the end of the call, press “” then “#” on your telephone. GS 4. EG The commands “3” (Full Arm), “4” (HA/PGM On), “5” (HA/PGM Off), “6” (Disarm) and “9” (Bell Cancel) can also be executed at any time during a Two-Way Audio session. Error beeps (three tones) are sounded in case of a wrong command. To clear the last command, press “” or “#”. Siren Muting AR The siren is muted during Two-Way Audio communication. At the end of the call, the siren is re-activated (if the Siren Cut-Off has not yet expired). You can cancel the reactivation of the siren by pressing “9” on your telephone during the call. -34- 7.2. Service Call To make a Service Call: • Press and hold down the Service Call key SR L The Service Call feature enables you to call the monitoring service by pressing one key. for a few seconds. If using Simplex mode, the call is connected in Listen mode – see Simplex Mode. 7.3. Two-Way Audio after an Alarm 7.4. Two-Way Audio Follow-Me AD In the event of Burglary, Fire and Emergency alarms, the Control System is able to report the events and then stay on the line. This allows the monitoring service to verify the alarm or provide assistance in the event of an emergency. ID This feature causes the Control System to call you in the event of an alarm so that you may check your family and home. When the Control System calls, you will hear two short tones when you pick up the phone. Press "2" on your telephone to answer the call. UR If you press “9” to answer the call, the Control System simultaneously cancels the siren when you answer the call. If using Simplex mode, the call is connected in Listen mode – see Simplex Mode. 7.5. Simplex Mode EG It is possible that the Two-Way Audio features on your system are programmed to operate in “Simplex” mode. Simplex mode means that one party may speak while the other party listens. If using Simplex mode, the call is connected in Listen mode. In Listen mode, the microphone on the Control System is turned on so that you can listen in. If you want to switch to Speak mode, press “1” on your telephone. AR GS In Speak mode, the microphone is turned off and the speaker is turned on so that you can speak to the person on the other end of the line. If you want to switch back to Listen mode, press “0” on your telephone. -35- Advanced System Operation SR L 8. Besides the basic functions described in the previous chapters, you can access additional functions via the menu. This chapter describes these functions and the menu navigation procedure. Menu Navigation Using the LCD keypad on the front panel, you can navigate through the menus using the menu navigation keys (/) and make simple yes/no decisions using the √ and Χ keys. AD The availability of menu items depends on the user code that you used to enter Menu mode. Some menu items are limited to the Master code only (User 1). Certain menu items, such as system programming functions, are not intended for the user and can only be accessed by the installer. The following example explains the procedure for Event Log viewing (Master code access only). Press √ to enter Menu mode. Enter the Master code; the first menu item in the main menu, Cancel Report is displayed. 3. Press until 6. Event Log is displayed. 4. Press √ to enter the Event Log menu; 1. View Log is displayed. 5. Press √ to choose the displayed item. Press Χ if you do not want to choose the displayed item. Pressing Χ also takes you back to the previous menu level. UR ID 1. 2. Menu mode automatically terminates two minutes after the last keystroke. EG Throughout this chapter, we have tried to include all of the system functions using a similar structure and order as they appear in the menu. The above procedure provides a detailed explanation of menu navigation. However, in order to simplify the procedures that appear in the rest of this chapter, the following conventions are used: This… Means… Enter the main menu by pressing √and entering your user code. Using the arrow keys, navigate until you reach Bypass Zones and press √. Using the arrow keys, navigate until you reach Unbypass All and press √. Select… Use the arrow keys to scroll through the options and press √. [61] The shortcut to a specific menu item from the main menu. In this case, this is the shortcut for View Log. These appear in the procedures as an additional aid to menu navigation. AR GS From the Bypass Zones menu, select Unbypass All. -36- 8.1. Cancel Report To cancel report: • 8.2. SR L The Cancel Report function enables you to prevent the system from reporting in the event of a false alarm. From the main menu, select Cancel Report [1]; all pending messages to the monitoring service are canceled. Zone Bypassing/Unbypassing AD When a zone is bypassed, its detector is ignored by the system and does not generate an alarm when triggered. ID To bypass or unbypass a zone: 1. From the Bypass Zones menu, select Bypass/Unbyp. [21]. 2. Using the arrow keys, scroll to the zone you want to bypass or unbypass. 3. Press √ to change the bypass status. 4. Press Χ; Save Changes? is displayed. 5. Press √ to confirm the changed bypass status. UR To unbypass all zones: 1. From the Bypass Zones menu, select Unbypass All [22]. 2. Press √; all zones are unbypassed All bypassed zones will be automatically unbypassed when the system is disarmed. A fire zone cannot be bypassed. 8.3. User Codes EG The iConnect supports a variety of individual user codes. Each of these codes is four digits long. Most system functions require you to enter a valid user code. The ability to perform a function is defined by your user code’s authorization level. These authorization levels are pre-defined for each code as explained below. GS Code 1: Master Code The Master code is the highest user authorization level. With the Master code, you can edit all other user codes. Additionally, the Master code grants access to the Event Log, the Service menu and Home Automation Schedule programming. AR The default Master code is 1234. Change this code immediately after the system has been installed. Codes 2-19: Controlled Codes When you use a controlled user code for arming and disarming, the system notifies the monitoring service. -37- Codes 20-25: Non-controlled Codes SR L Non-controlled codes do not cause the system to send Arm/Disarm reports to the monitoring service. The system sends a Disarm report only if you use this code to disarm the system after an alarm occurrence. Codes 26-27: Limited Codes A Limited code enables you to issue a code that is valid for one day only. This code automatically expires 24 hours after it has been programmed. Code 28: Duress Code AD The Duress code is designed for situations where you are being forced to operate the system. This user code grants access to the selected operation, while sending a Duress event message to the monitoring service. Code 29: Telecontrol Code Editing User Codes UR ID The Telecontrol code is designed to enable the user to perform a number of tasks via their telephone using DTMF commands. Using this code, the user can call their system to arm and disarm, turn on and off HA units, activate and deactivate the PGM output, cancel the siren or establish Two-Way Audio communication. This code can only be used for this specific purpose and does not grant access to any additional system functions such as disarming. User code editing is a feature that is available exclusively to the Master code. To maintain a high level of security, keep all user codes confidential. EG To edit a user code: 1. From the main menu select, User Codes [4]. 2. Select the code you want to edit; 3. From the code’s sub-menu, select Edit Code; the 4-digit code is displayed with the cursor flashing on the first digit. 4. Edit the code. 5. Press √; the new code is stored in the memory. AR GS If you enter a code that is identical to an existing user code, the Control System sounds an error tone and the new code is not accepted. 0000 is not a valid user code as this value is used to delete a user code. -38- Deleting User Codes SR L As an additional security measure, make certain that you delete any extra codes that are no longer required. AD To delete a user code: 1. From the main menu select, User Codes [4]. 2. Select the code you want to delete; 3. From the code’s sub-menu, select Edit Code; the 4-digit code is displayed with the cursor flashing on the first digit. 4. Enter 0000. 5. Press √; the code is deleted. The Master code cannot be deleted. User Code Descriptors Using the alphanumeric keypad on the front panel, you can edit the 16-character user code descriptors and enter the name or title of the users to whom the code is allocated. ID To enter text, press a key repeatedly to scroll through the characters that appear on the key. For example, press 6MNO to enter M, N, O, or 6 respectively. You can also use the 1 and 0 keys to enter symbols. After you enter text, the cursor automatically moves to the next character. During descriptor editing, use the left SOS button UR before the current character. Use the Right SOS button character. AR GS EG To edit a user code descriptor: 1. From the main menu, select User Codes [4]. 2. Select a code. 3. From the code’s sub-menu, select Descriptor. 4. Edit the descriptor using the alphanumeric keypad. 5. Press √ when you have finished editing. -39- to enter a space button to delete the current 8.4. Follow-Me SR L The Follow-Me feature is designed to notify the user that certain events have occurred. The events that are sent to the Follow-Me telephone number are those events that the user is authorized to view in the event log; events that can be viewed only by the installer are not sent to the Follow-Me number – see Two-Way Audio Follow-Me. If using the TWA Follow-Me feature, the audio channel is opened after alarm events only. AD To edit the Follow-me number: 1. From the main menu, select Telephone # [5]. 2. Enter a telephone number for Follow-Me communication. If using the SMS Follow-Me feature, this number must be for a cellular phone with the capability to receive SMS messages. You may only access Follow-me programming if the protocol for Account 3 is programmed as SMS or TWA Follow-me. 8.5. Event Log ID The event log records events that have occurred within your security system. When the log is full, the oldest events are automatically erased and are replaced by new events. 2. 3. 4. UR To view the event log: 1. From the Event Log menu, select View Log [61]; the most recent event is displayed. Press the left SOS button to display the Time/Date stamp or the default descriptor on the second row of the display. Use the arrow keys to scroll through the events. When you have finished viewing, press Χ to exit the log. EG The event log displays the following information for each event: The event – a brief description of the event that occurred. GS Zone descriptor – exactly where the event occurred. Time/date stamp – the exact time the event occurred. Report details – a single character indicating whether the event was reported to the central station. The options available are R: Report Sent, F: Report Failed or N: No Report. Default descriptor – in this case the number of the zone. AR The above example shows the event log entry for a Fire alarm in the Kitchen (Zone 4) on November 14th 2008. The report was successfully reported to the central station. -40- 8.6. Service Menu Set Time & Date To set the time: 1. From the Service menu, select Set Time/Date, Set Time [7011]. 2. Enter the current time. 3. Press √; the time is modified. SR L The Service menu includes various functions that enable you to test your system effectively. You can gain access to the Service menu using the Master code. AD To set the date: 1. From the Service menu, select Set Time/Date, Set Date [7012]. 2. Enter the current date. 3. Press √; the date is modified. The format of the time and date is defined by your installer in programming. If you are setting the time in 12hr format, use the ID Message Center key to toggle between AM and PM. UR The Message Center is designed to allow you to record a short message that may be played back later by another user. After a message is recorded, Message Waiting is displayed on the LCD until the message is played back. To play back a recorded message: • From the Service menu, select Messages, Play Message [7021]. EG To record a message: 1. From the Service menu, select Messages, Record Message [7022]. 2. Press √ to start recording the message. 3. Record your message. The message may be up to twenty seconds long. 4. Press √ to stop recording; the message is automatically played back and OK? is displayed. 5. Press √ to save your recording. GS To delete a message: 1. From the Service menu, select Messages, Delete Message [7023]; OK? is displayed. 2. Press √; the message is deleted. The Record and Play options can also be accessed via a convenient shortcut without needing to enter a valid user code. AR To access the Record Message option from Standby mode, press then Χ. To access the Play Message option from Standby mode, press then √. -41- Siren Tests • SR L To test the external wireless siren: From the Service menu, select Test and then WL Siren Test [7031]; the wireless siren is sounded briefly. To test the built-in siren: • From the Service menu, select Test and then Siren Test [7032]; the built-in siren is sounded briefly. Interface Test AD The Interface test enables you to check if the speaker, LEDs and LCD are functioning correctly. To test the system interface: • From the Service menu, select Test and then Interface Test [7033]; a short sequence of chimes are sounded from the speaker, all LEDs flash and the LCD is tested on all connected LCD keypads. ID Walk Test Walk Test mode enables you to test all the detectors registered to your system without triggering an alarm. Snapshot Test EG UR To initiate Walk Test mode: 1. From the Service menu, select Test and then Walk Test [7034]; a list of registered detectors appears. 2. Trigger each detector; when the system receives a successful transmission from a detector, the detector is removed from the list. 3. When all the detectors are removed from the list, End Walk Test is displayed. 4. Press Χ to exit Walk Test mode. The Snapshot Test enables you to check if the video verification detector cameras are functioning correctly AR GS To initiate the Snapshot Test: 1. From the Service menu, select Test and then Snapshot Test [7035]; a list of registered detectors appears. 2. Select a detector from the list and press √; a snapshot of the monitored area in taken and the results can be viewed in the Web User Application. 3. Repeat the test for each installed detector. 4. Press Χ to exit Snapshot Test mode. -42- Transmitters SR L The Transmitters menu offers a number of testing utilities, TX List, TX Test, RF Link and ENV. RSSI. The TX List comprises all registered transmitters and their last reported status. UR ID The TX list displays the following information for each transmitter: AD To view the TX list: 1. From the Service menu, select Transmitters, TX List [7041]; the first transmitter on the list is displayed. 2. Using the arrow buttons, scroll through the transmitter list. 3. When you have finished viewing, press Χ to exit the list. Means… OK The transmitter is functioning correctly TA Tamper condition Notify BT Battery low your OS The transmitter is out of synchronization installer NA EG This… The transmitter is inactive to display the transmitter’s default descriptor. AR GS Press The left SOS button -43- The second utility, TX Test enables you to identify transmitters. To initiate TX Test mode: 1. From the Service menu, select Transmitters, TX Test [7042]. 2. Activate a transmitter; the transmitter’s details are displayed. 3. When you have finished, press Χ to exit TX Test mode. Tones 1 1 Tone 2 2 – Tones 3 3 Tones 4 4 Tones AD Signal Strength SR L In TX Test mode, each time a transmission is received, a chime is sounded and the activated transmitter is displayed. The third utility, RF Link enables you to measure the RF noise levels between a selected transmitter and the system’s receiver. UR ID To view the Environment RF Link level reading: 1. From the Service menu, select RF Link Test [7043]; the first transmitter on the list is displayed. 2. Using the arrow buttons, scroll through the list and select a transmitter. 3. Press √ and activate the selected transmitter, e.g. press keyfob button. The RF noise levels of the selected transmitter and the system’s receiver are displayed. EG The fourth utility, Environmental RSSI enables you to measure the RF noise level of the systems environment. The Control System will start measuring the RSSI level every second, and it will display the result on the LCD. RSSI level can jump momentarily when a detector is activated. It doesn’t mean that the receiver is noisy. To view the Environment RSSI level reading: From the Service menu, select ENV. RSSI [7044]; the RF noise of the system's environment is displayed. AR GS • -44- Audio Volume Meaning 1 Increase microphone sensitivity 4 Reduce microphone sensitivity 3 Increase speaker volume 6 Reduce speaker volume AD 4. Reading Press √; the new settings are stored in the memory. GSM Signal Strength You can measure the GSM signal strength. To view the GSM signal strength reading: ID From the Service menu, select GSM Signal [706]; the signal strength of the cellular network is displayed. Reading Meaning 8-9 Reception is good 5-7 Reception is acceptable Less than 5 Display Version UR • SR L To adjust the sensitivity of the microphone and the volume of the speaker: 1. Establish a two-way audio connection. 2. From the Service menu, select Audio Volume [705]. 3. Adjust the setting according to the following table. Reception is unacceptable To display the system’s software and hardware versions: From the Service menu, select Version [707]; the software (SW) and (HW) versions are displayed. EG • Enable Programming GS The Enable Programming command allows a user to limit access to system programming. It means that the installer or Remote Programmer can access the system only after a user with Master code provides authorization using the Enable Programming command. To enable this feature, contact your installer. To grant access to the installer or Remote Programmer: From the Service menu, select Enable Prog. [708]; a 30-minute time window is opened during which the Installer Code is valid or RP communication may be established. AR • -45- Global Chime To enable or disable Global Chime: 1. From the Service menu, select Global Chime [709]. 2. Select either Enable or Disable. 3. Press √ when the desired setting is displayed. SR L Each detector can be programmed by your installer to cause the system to chime when activated. This feature is active only when the system is disarmed. For example, the system can be programmed to sound a chime each time the front door is opened or closed. The Global Chime option enables you to turn this feature on and off. AD Global Chime can also be accessed via a convenient shortcut without needing to enter a valid user code. To access the Global Chime option from Standby mode, press then . Remote Firmware Update The Remote Firmware Update command enables a user with Master code authorization to initiate the update from a remote PC using WEB communication. To initiate Remote Firmware Update: From the Programming menu, select Service, Remote Software Update [710]; a 24-hours time window is opened during which the Remote Firmware Update may be performed. IP Display UR • ID Note: to enable this feature, contact your installer. When using Ethernet connection, you can view the LAN IP address of the Control System, i.e. the address that your home router has assigned to the Control System. To display the IP Address: EG From the Programming menu, select Service, IP Display [711]; the LAN IP address of the Control System is displayed. AR GS • -46- AR GS EG UR ID AD SR L Appendix A: Menu Structure Legend: Installer code required -47- Master code required SR L Appendix B: Glossary 24hr Zone A detector which is always active regardless of whether the system is armed or disarmed. Armed The state during which the security system is activated. In most cases, when the system is armed, triggering a detector generates an alarm. Arming Keys The three keys on the front panel or keypad that activates one of the system’s arming options. Bypassed Zone A detector which is ignored by the system. No alarm is generated from a bypassed zone even if triggered when the system is armed. AD A B C A key on the Wireless Keypad that causes the system to disregard any partially entered code or command that may have mistakenly been entered. Cancel Report An operation that clears all communication buffers and stops the transmission of any pending messages to the monitoring service. Code Controlled Code Delay A feature that provides audible annunciation when specific detector s are activated. See User Code A user code that causes the system to notify the monitoring service when used to arm or disarm. D The exit/entry delay times that allow the user to arm or disarm the system without generating an alarm. Custom labels programmed for each user code, zone, keyfob, keypad etc. GS Descriptor UR Chime Monitoring and control via a cellular network. EG Cellular Communication ID Cancel Key The state during which the security system is deactivated. During disarm only detectors that are defined as 24hr, Panic, Medical, Fire, Gas, Flood and Environmental are capable of generating an alarm. Duress Code A user code that generates a silent alarm to indicate that the user is being forced to operate the system. AR Disarmed Entry Delay E See Delay Event Log A browsable record of events that have occurred within the system. Exit Delay See Delay -48- F A feature that enables users to receive notification to their telephone that an event has occurred in the system. Forced Arming Arming before the system is ready. If the system is not secured by the time that the exit delay expires, an alarm is generated. Front Panel The main interface located on the front of the Control System consisting of an LCD keypad. Full Arming An arming method that activates the entire system when the premises are vacated. SR L Follow-me G A feature that enables/disables the Chime feature for the entire system – see Chime. AD Global Chime H Home Automation Units (abbr.). The lights and appliances in the home that are controlled by the optional Home Automation feature. Home Automation An optional feature that enables the user to control electrical appliances and lights via the Control System. Instant Arm An arming method that cancels the entry delay after the system has been Part or Perimeter armed. Keyfob Handheld wireless transmitters used to remotely control the system. LAN IP Address The address that your home router has assigned to the Control System. UR I ID HA Units K Limited Code A user code that automatically expires 24 hours after it is programmed. See Event Log M GS Log EG L The only user code with the ability to program other user codes. The Master code also has exclusive access to specific system functions. Medical Emergency A type of alarm that informs the monitoring service that the user is in need of medical assistance. Message Center An optional feature that enables users to record messages to be played back by other users. AR Master Code -49- N A user code that does not cause the system to notify the monitoring service when used to arm or disarm. The system only reports if the code is used to disarm after an alarm. SR L Non-Controlled Code O One-Key Arming Arming the system without the need for a valid user code. P A user initiated event that alerts the monitoring service in the event of an emergency. Part Arming An arming method that is designed to activate a certain section of the premises. Perimeter Arming An arming method that is designed to activate the detectors protecting the doors and windows while enabling residents to move freely on the premises. PGM Programmable output that is triggered according to specific system status conditions, or by remote command sent via PSTN, GSM, Ethernet, keyfob, keypad, or Remote Programmer. R ID AD Panic Alarm The state in which all zones are closed and the system is ready to be armed. Remote Firmware Update Control System's firmware update from a remote PC using WEB communication. Restore The restoral of a trouble condition to its normal state. For example, if AC power is reconnected, an AC Loss Restore event code is sent to the central station. RSSI Received Signal Strength Indication (abbr.) RF noise of the system's receiver. S A Home Automation feature that switches HA units on and off automatically according to pre-set times. The devices installed around the home that alert the panel in the event of an alarm. GS Detectors EG Scheduling UR Ready A feature that enables the user to contact the monitoring service and talk to an operator via the Control System. SMS Command An SMS message sent to the Control System that causes the system to perform a specific function. Smartkey An RF ID device used to arm and disarm the system by placing it against the Wireless Keypad. AR Service Call SMS Confirmation An SMS message sent to the user confirming that the SMS command has been performed. System Status LEDs Luminous indicators on the front panel that provide information on the arm and power status of the system. -50- T Tones Trouble Tones TWA TX A feature that provides remote access via the telephone including remote arming/disarming, siren cancel and Two-Way audio. SR L Telecontrol Chimes sounded by the Control System’s internal or external siren. Tones sounded by the system to indicate a trouble condition. Two-Way Audio (abbr.) Transmitter (abbr.) A service feature that lists all the system’s registered transmitters, their last recorded status and signal strength. TX Test A service feature that displays the source of the last received transmission. AD TX List U Unbypass The restoral of a bypassed zone to its original state. User Code A four-digit code that grants access to certain system functions such as arming and disarming the system. A user code that enables Two-Way Audio communication. W ID User TWA Code A mode that enables detectors to be tested without generating an alarm. Web Remote Programmer Software that enable installers or service providers to operate and program the system from a PC either on-site or from a remote location. Wireless Keypad Intelligent two-way wireless keypad with large LCD display that serves as an additional user interface of the Control System. UR Walk Test Zone A protected area within the security system. See Bypassed Zone AR GS Zone Bypassing EG Z -51- Electronics Line 3000 Ltd. Limited Warranty EG UR ID AD SR L EL and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 24 months from the date of production. Because Seller does not install or connect the product and because the product may be used in conjunction with products not manufactured by the Seller, Seller cannot guarantee the performance of the security system which uses this product. Sellers' obligation and liability under this warranty is expressly limited to repairing and replacing, at Sellers option, within a reasonable time after the date of delivery, any product not meeting the specifications. Seller makes no other warranty, expressed or implied, and makes no warranty of merchantability or of fitness for any particular purpose. In no case shall seller be liable for any consequential or incidental damages for breach of this or any other warranty, expressed or implied, or upon any other basis of liability whatsoever. Sellers obligation under this warranty shall not include any transportation charges or costs of installation or any liability for direct, indirect, or not be compromised or circumvented; that the product will prevent any persona; injury or property loss by intruder, robbery, fire or otherwise; or that the product will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of intruder, robbery or fire without warning, but is not insurance or a guaranty that such will not occur or that there will be no personal injury or property loss as a result. Consequently seller shall have no liability for any personal injury, property damage or loss based on a claim that the product fails to give warning. However, if seller is held liable, whether directly or indirectly, for any loss or damage arising from under this limited warranty or otherwise, regardless of cause or origin, sellers maximum liability shall not exceed the purchase price of the product, which shall be complete and exclusive remedy against seller. No employee or representative of Seller is authorized to change this warranty in any way or grant any other warranty. WARNING: This product should be tested at least once a week. CAUTION: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to local regulations. Contacting Electronics Line 3000 Ltd. GS International Headquarters: Electronics Line 3000 Ltd. 14 Hachoma St., 75655 Rishon Le Zion, Israel Tel: (+972-3) 963-7777 Fax: (+972-3) 961-6584 All rights reserved. AR No part of this document may be reproduced in any form without prior written permission from the publisher. Electronics Line 3000 Ltd. 02/2012 5IN1772 -52- ">

Public link updated
The public link to your chat has been updated.
Advertisement