Advertisement
Advertisement
USER’S GUIDE
MFC-3360C
Version A
If you need to call Customer Service
Please complete the following information for future reference:
Model Number: MFC-3360C
Serial Number:
Date of Purchase:
Place of Purchase:
1
The serial number is on the back of the unit. Retain this User's Guide with your sales receipt as a permanent record of your purchase, in the event of theft, fire or warranty service.
Register your product on-line at http://www.brother.com/registration/
By registering your product with Brother, you will be recorded as the original owner of the product. Your registration with Brother:
may serve as confirmation of the purchase date of your product should you lose your receipt; and
may support an insurance claim by you in the event of product loss covered by insurance.
© 2006 Brother Industries, Ltd.
Approval Information and Compilation and
Publication Notice
THIS EQUIPMENT IS DESIGNED TO WORK WITH A TWO WIRE ANALOGUE PSTN LINE
FITTED WITH THE APPROPRIATE CONNECTOR.
APPROVAL INFORMATION
Brother advises that this product may not function correctly in a country other than where it was originally purchased, and does not offer any warranty in the event that this product is used on public telecommunication lines in another country.
Compilation and Publication Notice
Under the supervision of Brother Industries Ltd., this manual has been compiled and published, covering the latest product descriptions and specifications.
The contents of this manual and the specifications of this product are subject to change without notice.
Brother reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication.
i
ii
EC Declaration of Conformity under the R & TTE
Directive
Table of Contents
Section I General
1
2
3
4
General Information 2
Symbols and conventions used in the documentation .................................... 2
Loading documents and paper 6
Loading paper, envelopes and other media ........................................................11
Loading paper and other media ....................................................................11
Loading envelopes and post cards................................................................ 13
General setup 16
Putting your machine in Power Save mode...................................................16
Bringing your machine out of Power Save mode ..........................................16
Security features 19
Setting and changing the TX Lock password ................................................ 19
iii
Section II Fax
5
6
Sending a fax 22
Cancelling a Broadcast in progress...............................................................23
Sending faxes using multiple settings ...........................................................23
Dual access (Monochrome only) ...................................................................24
Delayed Faxing (Monochrome only)..............................................................25
Delayed Batch Transmission (Monochrome only).........................................26
Checking and cancelling waiting jobs............................................................26
Sending a fax at the end of a conversation ...................................................26
Receiving a Fax 27
F/T Ring Time (Fax/Tel mode only)...............................................................29
Receiving a fax at the end of a conversation.................................................31
iv
7
8
9
Telephone and External devices 32
Fax/Tel mode in Power Save condition ......................................................... 32
Connecting an external TAD (telephone answering device)................................35
Recording an outgoing message (OGM) on an external TAD.......................35
Connecting an external or extension telephone ............................................36
Operation from extension telephones............................................................ 36
Using extension telephones (For U.K. only) .................................................. 37
Using a cordless external telephone .............................................................38
Dialling and storing numbers 39
Storing One-Touch Dial numbers ..................................................................41
Changing One-Touch and Speed-Dial numbers ........................................... 42
Setting up Groups for broadcasting...............................................................42
Combining Quick-Dial numbers..................................................................... 43
Remote fax options 44
Setting a Remote Access Code..................................................................... 45
Using your Remote Access Code..................................................................46
Changing your Fax Forwarding number ........................................................47
v
10 Printing Reports 49
11 Polling 51
Setup to receive polling with a secure code ..................................................51
Setup for polled transmit with secure code....................................................53
Section III Copy
12 Making copies 56
Changing copy speed and quality .................................................................58
Enlarging or reducing the image copied ........................................................58
Sorting copies using the ADF (Monochrome only) ........................................60
Adjusting Brightness, Contrast and Colour....................................................60
Section IV Software
13 Software features 64
vi
Section V Appendixes
A
B
C
Safety and Legal 66
IMPORTANT - For your safety ......................................................................71
EU Directive 2002/96/EC and EN50419........................................................72
Troubleshooting and Routine Maintenance 74
If you are having difficulty with your machine ................................................ 74
Transferring your faxes or Fax Journal report ...............................................81
Cleaning the outside of the machine .............................................................87
Cleaning the machine printer platen.............................................................. 89
Menu and Features 94
vii
viii
D
E
F
Specifications 103
Glossary 112
Index 116
Section I
General
General Information
Loading documents and paper
General setup
Security features
I
2
1
General Information
Using the documentation
Thank you for buying a Brother machine!
Reading the documentation will help you make the most of your machine.
1
Symbols and conventions used in the documentation
The following symbols and conventions are used throughout the documentation.
1
Bold
Italics
Bold typeface identifies specific keys on the machine’s control panel.
Italicized typeface emphasizes an important point or refers you to a related topic.
Courier
New
Text in the Courier New font identifies messages on the
LCD of the machine.
Warnings tell you what to do to prevent possible personal injury.
Electrical Hazard icons alert you to possible electrical shock.
Cautions specify procedures you must follow or avoid to prevent possible damage to the machine or other objects.
Notes tell you how you should respond to a situation that may arise or give tips about how the operation works with other features.
Improper Setup icons alert you to devices and operations that are not compatible with the machine.
Accessing the
Software User’s Guide
1
This User’s Guide does not contain all the information about the machine such as how to use Printer, Scanner and PC Fax. When you are ready to learn detailed information about these operations, read the Software
User’s Guide that is on the CD-ROM.
Viewing Documentation
1
Viewing Documentation
(For Windows
®
)
To view the documentation, from the Start menu, point to Brother, MFC-XXXX (where
XXXX is your model name) from the programs group, and then select
User’s Guide.
If you have not installed the software, you can find the documentation by following the instructions below:
1 a
Turn on your PC. Insert the Brother
CD-ROM into your CD-ROM drive.
b
If the model name screen appears, click your model name.
1
c
If the language screen appears, click your language. The CD-ROM main menu will appear.
General Information
Viewing Documentation
(For Macintosh
®
)
a
Turn on your Macintosh
®
. Insert the
Brother CD-ROM into your CD-ROM drive. The following window will appear.
1
1
Note
If this window does not appear, use
Windows
®
Explorer to run the setup.exe program from the root directory of the
Brother CD-ROM.
d
Click User’s Guide to view the Software
User’s Guide in HTML format.
How to find Scanning instructions
There are several ways you can scan documents. You can find the instructions as follows:
1
Software User’s Guide
Scanning
(For Windows
®
98/98SE/Me/2000
Professional and Windows
®
XP)
ControlCenter3
(For Windows
®
98/98SE/Me/2000
Professional and Windows
®
XP)
PaperPort
®
SE with OCR User’s Guide
Instructions for scanning directly from
ScanSoft
®
PaperPort
®
SE with OCR
User’s Guide. The complete ScanSoft
®
PaperPort
®
SE with OCR User’s Guide can be viewed from the Help selection in the ScanSoft
®
PaperPort
® application.
SE with OCR b
Double-click the Documentation icon.
c
Double-click your language folder.
d
Double-click the Top Page file to view the Software User’s Guide in HTML format.
Software User’s Guide:
Software User’s Guide in HTML format
How to find Scanning instructions
There are several ways you can scan documents. You can find the instructions as follows:
Software User’s Guide
Scanning
(For Mac OS
®
X 10.2.4 or greater)
ControlCenter2
(For Mac OS
®
X 10.2.4 or greater)
Presto!
®
PageManager
®
User’s Guide
Instructions for scanning directly from
Presto!
®
PageManager
®
. The complete
Presto!
®
PageManager
®
User’s Guide can be viewed from the Help selection in the Presto!
®
PageManager
®
application.
1
3
Chapter 1
Control panel overview
MFC-3360C
2 1
1
1
3
4
6 5
1 Power Save
Lets you put the machine into Power Save mode.
2 LCD (liquid crystal display)
Displays messages on the screen to help you set up and use your machine.
3 One-Touch keys
Instantly accesses your stored Quick-Dial numbers.
Shift
When held down, lets you access
One-Touch numbers 6 to 10.
4 Fax keys
Redial/Pause
Redials the last number called. It also inserts a pause when programming quick-dial numbers.
Resolution
Lets you temporarily change the resolution when sending a fax.
Mute
Puts the current phone call on hold.
7 8 9
Tel/R
Use this key to gain access to an outside line, or transfer a call to another extension when the machine is connected to a PBX.
5 Copy key
Copy Options
Lets you temporarily change multiple copy settings when in copy mode.
6 Ink Management
Lets you clean the print head, check the print quality, and check the available ink volume.
7 Dial Pad
Use these keys to dial telephone and fax numbers and as a keyboard for entering information into the machine.
The # key lets you temporarily switch the dialling mode during a telephone call from
Pulse to Tone.
4
11
10
8 Menu keys:
Menu
Lets you access the menu to program your settings into the machine.
a Search/Speed Dial
Lets you look up and dial numbers that are stored in the memory.
Volume keys
d c
In Fax mode, you can press these keys to adjust the ring volume.
d
Press to scroll backward to a menu selection.
a or b
Press to scroll through the menus and options.
Clear/Back
Press to cancel the current setting.
OK
Lets you store your settings in the machine.
9 Start keys:
Colour
Lets you start sending faxes or making copies in full colour. Also lets you start a scanning operation (in colour or mono, depending on the scanning setting in the
ControlCenter software).
Mono
Lets you start sending faxes or making copies in monochrome. Also lets you start a scanning operation (in colour or mono, depending on the scanning setting in the
ControlCenter software).
10 Stop/Exit
Stops an operation or exits from a menu.
11 Mode keys:
Fax
Lets you access Fax mode.
Scan
Lets you access Scan mode.
Copy
Lets you access Copy mode.
General Information
1
5
6
2
Loading documents and paper
2
Loading documents
You can send a fax, make copies, and scan from the ADF (automatic document feeder).
2
Using the ADF
The ADF can hold up to 20 pages and feeds each sheet individually. Use standard
80 g/m
2
(20 lb) paper and always fan the pages before putting them in the ADF.
2
Recommended environment
2
Temperature:
Humidity:
Paper:
20 to 30 ° C (68 to 86° F)
50% to 70%
80 g/m
2
A4 (20 lb LTR)
Document Sizes Supported
Length:
Width:
Weight:
127 to 355.6 mm (5 to 14 in.)
89 to 215.9 mm
(3.5 to 8.5 in.)
64 to 90 g/m
2
(17 to 24 lb)
2
How to load documents
CAUTION
DO NOT pull on the document while it is feeding.
DO NOT use paper that is curled, wrinkled, folded, ripped, stapled, paper clipped, pasted or taped.
DO NOT use cardboard, newspaper or fabric.
2
Make sure documents written with ink are completely dry.
a
Open the document support (1) and the document tray (2) and then pull out the extension (3).
1
2
3 b
Fan the pages well. Make sure you put the documents face down, top edge
first in the ADF until you feel them touch the feed roller. c
Adjust the paper guides (1) to fit the width of your documents.
1
Scanning area
The scannable area depends on the settings in the application you are using. The figures below show the areas you cannot scan on paper.
3 4
1
2
2
Usage Document
Size
Top (1)
Fax
Copy
Scan
Letter
A4
Letter
A4
Letter
A4
Bottom (2)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
Left (3)
Right (4)
4 mm
(0.16 in.)
1 mm
(0.04 in.)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
3 mm
(0.12 in.)
0 mm
(0 in.)
Loading documents and paper
Acceptable paper and other media
2
The print quality can be affected by the type of paper you are using in the machine.
To get the best print quality for the settings you have chosen, always set the Paper Type to match the type of paper you load.
You can use plain paper, inkjet paper (coated paper), glossy paper, transparencies and envelopes.
We recommend testing various paper types before buying large quantities.
For best results, use Brother paper.
When you print on inkjet paper (coated paper), transparencies and glossy paper, be sure to choose the correct media in the
‘Basic’ tab of the printer driver or in the
Paper Type setting of the menu. (See
When you print on Brother photo paper, load the instruction sheet included with the photo paper in the paper tray first, and then put the photo paper on top of the instruction sheet.
When you use transparencies or glossy paper, remove each sheet at once to prevent smudging or paper jams.
Avoid touching the printed surface of the paper immediately after printing; the surface may not be completely dry and may stain your fingers.
2
7
8
Chapter 2
Recommended media
To get the best print quality, we suggest using
Brother paper. (See table below.)
If Brother paper is not available in your country, we recommend testing various papers before purchasing large quantities.
We recommend using ‘3M Transparency
Film’ when you print on transparencies.
2
Brother paper
Paper Type
A4 Plain
A4 Glossy Photo
A4 Inkjet (Matte)
10 x 15 cm Glossy Photo
Item
BP60PA
BP61GLA
BP60MA
BP61GLP
Handling and using media
Store paper in its original packaging, and keep it sealed. Keep the paper flat and away from moisture, direct sunlight and heat.
The coated side of glossy paper is shiny.
Avoid touching the shiny (coated) side.
Load glossy paper with the shiny side facing down.
Avoid touching either side of transparencies because they absorb water and perspiration easily, and this may cause decreased output quality.
Transparencies designed for laser printers/copiers may stain your next document. Use only transparencies recommended for inkjet printing.
2
Improper Setup
DO NOT use the following kinds of paper:
• Damaged, curled, wrinkled, or irregularly shaped paper
1
1
1 2 mm (0.08 in.) or longer
• Extremely shiny or highly textured paper
• Paper already printed on by a printer
• Paper that cannot be arranged uniformly when stacked
• Paper made with a short grain
Paper capacity of the output paper tray
Up to 50 sheets of 20 lb Letter or 80 g/m
2
A4 paper.
Transparencies or glossy paper must be picked up from the output paper tray one page at a time to avoid smudging.
2
Choosing the right media
Paper type and size for each operation
Paper Type Paper Size
Cut Sheet
Cards
Envelopes
Transparencies
Letter
A4
Legal
Executive
JIS B5
A5
A6
Photo
Photo 2L
Index Card
216 × 279 mm (8 1/2 × 11 in.)
210 × 297 mm (8.3 × 11.7 in.)
216 × 356 mm (8 1/2 × 14 in.)
184 × 267 mm (7 1/4 × 10 1/2 in.)
182 × 257 mm (7.2 × 10.1 in.)
148 × 210 mm (5.8 × 8.3 in.)
105 × 148 mm (4.1 × 5.8 in.)
10 × 15 cm (4 × 6 in.)
13 × 18 cm (5 × 7 in.)
127 × 203 mm (5 × 8 in.)
100 × 148 mm (3.9 × 5.8 in.)
148 × 200 mm (5.8 × 7.9 in.)
Post Card 1
Post Card 2
(Double)
C5 Envelope 162 × 229 mm (6.4 × 9 in.)
DL Envelope 110 × 220 mm (4.3 × 8.7 in.)
COM-10
Monarch
105 × 241 mm (4 1/8 × 9 1/2 in.)
98 × 191 mm (3 7/8 × 7 1/2 in.)
JE4 Envelope 105 × 235 mm (4.1 × 9.3 in.)
Letter 216 × 279 mm (8 1/2 × 11 in.)
A4 210 × 297 mm (8.3 × 11.7 in.)
Loading documents and paper
2
2
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Yes
–
Usage
Fax
Yes
Yes
–
–
–
–
–
Yes
Copy Printer
Yes
Yes
Yes
Yes
Yes
–
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
–
–
–
–
–
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
2
9
Chapter 2
Paper weight, thickness and capacity
Paper Type Weight
1
Cut
Sheet
Plain Paper
Index Card
64 to 120 g/m
2
(17 to 32 lb)
Inkjet Paper 64 to 200 g/m
2
(17 to 53 lb)
Glossy Paper Up to 220 g/m 2
(Up to 58 lb)
Cards Photo Card Up to 240 g/m
2
(Up to 64 lb)
Up to 120 g/m
2
(Up to 32 lb)
Post Card
Envelopes
Transparencies
Up to 200 g/m
2
(Up to 53 lb)
75 to 95 g/m
2
(20 to 25 lb)
–
Up to 50 sheets for Legal size paper 80 g/m 2 (20 lb).
Up to 100 sheets of 80 g/m 2 (20 lb) paper.
Thickness No. of sheets
0.08 to 0.15 mm (0.003 to 0.006 in.) 100
0.08 to 0.25 mm (0.003 to 0.01 in.) 20
Up to 0.25 mm (Up to 0.01 in.) 20
Up to 0.28 mm (Up to 0.01 in.)
Up to 0.15 mm (Up to 0.006 in.)
Up to 0.23 mm (Up to 0.01 in.)
Up to 0.52 mm (Up to 0.02 in.)
–
20
30
30
10
10
2
10
Loading paper, envelopes and other media
Loading paper and other media
a
Pull the paper tray completely out of the machine.
If the paper support flap (1) is open, close it. Open the output paper tray cover (2).
2
2
Loading documents and paper b
If you are using Letter, A4 or Legal size paper, press and hold the universal guide release button (1) as you slide out the front of the paper tray to match the paper size you are using.
2
1
1 c
Press and slide the paper side guides (1) and paper length guide (2) to fit the paper size.
1
2
2 d
Fan the stack of paper well to avoid paper jams and misfeeds.
Note
Always make sure that the paper is not curled.
11
Chapter 2 e
Gently put the paper into the paper tray print side down and top edge first.
Check that the paper is flat in the tray.
h
Slowly push the paper tray completely into the machine.
f
Gently adjust the paper side guides with both hands and the paper length guide to fit the paper.
Make sure that the paper guides touch the edges of the paper.
i
While holding the paper tray in place, pull out the paper support (1) until it clicks and unfold the paper support flap (2).
2
Note
Be careful that you do not push the paper in too far; it may lift at the back of the tray and cause feed problems.
g
Close the output paper tray cover (1) and slide it forward.
1
Note
Do not use the paper support flap for
Legal paper.
1
12
Loading envelopes and post cards
2
Loading envelopes
Use envelopes that weigh from 75 to
95 g/m
2
(20 to 25 lb).
Some envelopes need margin settings to be set in the application. Make sure you do a test print first.
2
CAUTION
Do not use any of the following types of envelopes, as they will cause paper feed problems:
1 Envelopes with a baggy construction.
2 Embossed envelopes (those with a raised surface).
3 Envelopes with clasps or staples.
4 Envelopes that are pre-printed on the inside.
Glue Double flap
Occasionally you may experience paper feed problems caused by the thickness, size and flap shape of the envelopes you are using.
Loading documents and paper
How to load envelopes and post cards
2 a
Before loading, press the corners and sides of the envelopes or post cards to make them as flat as possible.
Note
If the envelopes or post cards are ‘doublefeeding,’ put one envelope in the paper tray at a time.
b
Put the envelopes or post cards into the paper tray with the address side down and the leading edge (top of the envelopes) in first. Slide the paper side guides (1) and paper length guide (2) to fit the size of the envelopes or post cards.
1
2
2
13
Chapter 2
If you have problems when printing on envelopes, try the following suggestions:
2 a
Open the envelope flap.
b
Make sure the open flap is either to the side of the envelope or to the back edge of the envelope when printing.
c
Adjust the size and margin in your application.
Removing small prints from the machine
When the machine ejects small paper onto the output paper tray, you may not be able to reach it. Make sure printing has finished, and then pull the tray completely out of the machine.
2
14
Loading documents and paper
Printable Area
The printable area depends on the settings in the application you are using. The figures below show the unprintable areas on cut sheet paper and envelopes. The machine can only print in the shaded areas when the Borderless print feature is available and turned on.
2
2
Cut Sheet Paper
3
1
4
Envelopes
1
3 4
2 2
Cut Sheet
Envelopes
Top (1)
3 mm (0.12 in.)
12 mm (0.47 in.)
Bottom (2)
3 mm (0.12 in.)
24 mm (0.95 in.)
Note
The Borderless feature is not available for envelopes.
Left (3)
3 mm (0.12 in.)
3 mm (0.12 in.)
Right (4)
3 mm (0.12 in.)
3 mm (0.12 in.)
15
16
3
General setup
Power Save mode
When the machine is idle, you can put the machine into Power Save mode by pressing the Power Save key. You can still receive telephone calls in Power Save mode. For further information on receiving faxes in the power save condition, please see the table on
page 16. If you want to do other operations,
you must take the machine out of Power Save mode.
3
Note
If you have connected an external telephone or TAD, it is always available.
Putting your machine in
Power Save mode
3 a
Press and hold down the Power Save key until the LCD shows
Shutting Down
.
The LCD light goes off.
Bringing your machine out of
Power Save mode
3 a
Press Power Save key.
Note
• Even if you have put the machine into
Power Save mode, it will periodically clean the print head to preserve print quality.
• If you unplug the AC power cord, no machine operations will be available.
• You can customize Power Save mode so that, apart from automatic head cleaning, no machine operations are available. (See
Power Save setting on page 16.)
Power Save setting
You can customize the machine's
Power Save key. The default mode is
Fax Receive:On
. Your machine can receive faxes or calls even when the machine is in Power Save mode. If you do not want your machine to receive faxes or calls, turn this setting to Fax Receive:Off. (See
a
Press Menu, 1, 6.
b
Press a or b to choose
Fax Receive:On
, or
Fax Receive:Off
.
Press OK.
c
Press Stop/Exit.
3
1
On/Off setting
Fax Receive:
(factory setting)
Fax Receive:
Off
Receive mode
Fax Only
External
TAD
Fax/Tel
Manual
—
Available operations
Fax Receive
Fax Detect
Fax Forward
Fax Storage
Remote Retrieval
Fax Detect
No machine operations will be available other than cleaning the print head.
2
3
You can receive telephone calls by lifting the handset.
You cannot receive a fax with Mono Start or
Colour Start.
Should be set before you switch off the machine.
3
Mode Timer
The machine has three temporary mode keys on the control panel: Fax, Scan, and Copy.
You can change the amount of time the machine takes after the last Scan or Copy operation before it returns to Fax mode. If you choose Off, the machine stays in the mode you used last.
a
Press Menu, 1, 1.
b
Press a or b to choose 0 Sec,
30 Secs
, 1 Min, 2 Mins, 5 Mins or
Off
.
Press OK.
c
Press Stop/Exit.
Paper settings
Paper Type
To get the best print quality, set the machine for the type of paper you are using.
a
Press Menu, 1, 2.
b
Press a or b to choose Plain Paper,
Inkjet Paper
, Brother Photo,
Other Photo
or Transparency.
Press OK.
c
Press Stop/Exit.
Note
The machine ejects paper with printed surfaces face up onto the paper tray in the front of the machine. When you use transparencies or glossy paper, remove each sheet at once to prevent smudging or paper jams.
3
3
3
General setup
Paper Size
You can use five sizes of paper for printing copies: Letter, Legal, A4, A5, and 10 × 15 cm
(4” × 6” in.) and three sizes for printing faxes:
Letter, Legal and A4. When you change the size of paper you load in the machine, you will need to change the paper size setting at the same time so your machine can fit an incoming fax on the page.
a
Press Menu, 1, 3.
b
Press a or b to choose Letter,
Legal
, A4, A5 or 10x15cm.
Press OK.
c
Press Stop/Exit.
3
3
Volume Settings
Ring Volume
You can choose a range of ring volume levels, from High to Off.
While in Fax mode , press d or c to adjust the volume level. The LCD shows the current setting, and each key press will change the volume to the next level. The machine will keep the new setting until you change it.
You can also change the volume through the menu, by following the instructions below:
3
Setting the Ring Volume from the menu
a
Press Menu, 1, 4, 1.
b
Press a or b to choose Low, Med,
High
or Off.
Press OK.
c
Press Stop/Exit.
3
3
17
Chapter 3
Beeper Volume
When the beeper is on, the machine will beep when you press a key, make a mistake or after you send or receive a fax.
You can choose a range of volume levels, from High to Off.
a
Press Menu, 1, 4, 2.
b
Press a or b to choose Low, Med,
High
or Off
Press OK.
c
Press Stop/Exit.
3
Speaker Volume
You can choose a range of speaker volume levels, from High to Off.
a
Press Menu, 1, 4, 3.
b
Press a or b to choose Low, Med,
High
or Off.
Press OK.
c
Press Stop/Exit.
3
Automatic Daylight
Savings Time
You can set the machine to change automatically for daylight savings time. It will reset itself forward one hour in the Spring and backward one hour in the Autumn. Make sure you have set the correct date and time in the
Date/Time
setting.
a
Press Menu, 1, 5.
b
Press a or b to select On or Off.
Press OK.
c
Press Stop/Exit.
3
LCD display
LCD Contrast
You can adjust the LCD contrast for a sharper and more vivid display. If you are having difficulty reading the LCD, try changing the contrast setting.
a
Press Menu, 1, 7.
b
Press a or b to choose Light or
Dark
.
Press OK.
c
Press Stop/Exit.
3
3
18
4
Security features
4
TX Lock
TX Lock lets you prevent unauthorized access to the machine.
You will not be able to schedule Delayed
Faxes or Polling jobs. However, any pre-scheduled Delayed Faxes will be sent even if you turn on TX Lock so they will not be lost.
While TX Lock is On, the following operations are available:
Receiving faxes
Receiving calls
Fax Forwarding
(If Fax Forwarding was already On.)
Remote retrieval
(If Fax Storage was already On.)
While TX Lock is On, the following operations are NOT available:
Sending faxes
Copying
PC printing
Scanning
4
Note
If you forget the TX Lock password, please call your Brother dealer for service.
Setting and changing the
TX Lock password
4
Note
If you have already set the password, you will not need to set it again.
Setting up the password
a
Press Menu, 2, 0, 1.
b
Enter a 4-digit number for the password.
Press OK.
c
When the LCD shows Verify:, reenter the password.
Press OK.
d
Press Stop/Exit.
4
Changing the TX Lock password
a
Press Menu, 2, 0, 1.
b
Press a or b to choose
Set Password
.
Press OK.
c
Enter a 4-digit number for the current password.
Press OK.
d
Enter a 4-digit number for the new password.
Press OK.
e
When the LCD shows Verify:, re-enter the password.
Press OK.
f
Press Stop/Exit.
4
4
19
Chapter 4
Turning TX Lock on/off
Turning TX Lock on
a
Press Menu, 2, 0, 1.
b
Press a or b to choose Set TX Lock.
Press OK.
c
Enter the registered 4-digit password.
Press OK.
The machine goes offline and the LCD shows TX Lock Mode.
4
Turning TX Lock off
a
Press Menu.
b
Enter the registered 4-digit password.
Press OK.
TX lock is automatically turned off.
4
Note
If you enter the wrong password, the LCD shows Wrong Password and stays offline. The machine will stay in TX Lock mode until the registered password is entered.
4
20
Section II
Fax
Sending a fax
Receiving a Fax
Telephone and External devices
Dialling and storing numbers
Remote fax options
Printing Reports
Polling
II
5
Sending a fax
Entering Fax mode
To enter fax mode, press the key will glow green.
Faxing from the ADF
(Fax), and
5
5 a
Make sure you are in Fax mode .
b
Put the document face down in the ADF.
c
Dial the fax number.
d
Press Mono Start or Colour Start.
The machine starts scanning the document.
Note
• To cancel, press Stop/Exit.
• If the memory is full, the document will be sent in real time.
Colour fax transmission
5
Your machine can send a colour fax to machines that support this feature.
However, colour faxes cannot be stored in the memory. When you send a colour fax, the machine will send it in real time (even if
Real Time TX
is set to Off).
Cancelling a fax in progress
5
If you want to cancel a fax while the machine is scanning, dialling or sending, press
Stop/Exit.
Broadcasting
(Monochrome only)
Broadcasting is when the same fax message is automatically sent to more than one fax number. You can include Groups,
One-Touch, Speed-Dial numbers, and up to
50 manually dialled numbers in the same broadcast.
After the broadcast is finished, a Broadcast
Report will be printed.
5 a
Make sure you are in Fax mode .
b
Load your document.
c
Enter a number. Press OK.
You can use either a One-Touch, a
Speed-Dial, a Group, or a manually entered number.
d
Repeat c until you have entered all the
fax numbers you wish to broadcast to.
e
Press Mono Start.
Note
• If you did not use up any of the numbers for Groups, access codes or credit card numbers, you can ‘broadcast’ faxes to as many as 160 different numbers.
• The available memory will vary depending on the types of jobs in the memory and the number of locations used for broadcasting. If you broadcast to the maximum numbers available, you will not be able to use dual access.
• Enter the long dialling sequence numbers as you would normally, but remember that each One-Touch and Speed-Dial number counts as one number, so the number of locations you can store becomes limited.
• If the memory is full, press Stop/Exit to stop the job. If more than one page has been scanned, press Mono Start to send the portion that is in the memory.
22
5
Cancelling a Broadcast in progress
a
Press Menu, 2, 6.
The LCD will show the fax number being dialled.
b
Press OK.
The LCD will show the job number:
XXXXXXXXX
1.Clear
2.Exit
c
Press 1 to clear.
The LCD will then show the Broadcast job number and 1.Clear
2.Exit
.
d
To cancel the Broadcast, press 1.
e
Press Stop/Exit.
5
Additional sending operations
Sending faxes using multiple settings
5
When you send a fax you can choose any combination of these settings: resolution, contrast, overseas mode and real time transmission.
a
Make sure you are in Fax mode .
b
Load your document.
c
Choose a setting you want to change.
Press OK.
d
Do one of the following:
Next
1.Yes 2.No
Press 1 to change another setting.
Press 2 when you have finished choosing your settings.
e
Send the fax as usual.
5
Sending a fax
Contrast
If your document is very light or very dark, you may want to change the contrast. For most documents the default setting Auto can be used. It automatically chooses the suitable contrast for your document.
Use Light when sending a light document.
Use Dark when sending a dark document.
5 a
Make sure you are in Fax mode .
b
Load your document.
c
Press Menu, 2, 2, 1.
d
Press a or b to choose Auto, Light or Dark.
Press OK.
Note
Even if you choose Light or Dark, the machine will send the fax using the Auto setting in any of the following conditions:
• When you send a colour fax.
• When you choose Photo as the Fax
Resolution.
Changing Fax Resolution
5
The quality of a fax can be improved by changing the fax resolution. Resolution can be changed for the next fax or for all faxes.
5
To change the fax resolution for the next fax
5 a
Make sure you are in Fax mode .
b
Load your document.
c
Press Resolution and then a or b to choose the resolution.
Press OK.
23
Chapter 5
To change the default fax resolution
5 a
Make sure you are in Fax mode .
b
Press Menu, 2, 2, 2.
c
Press a or b to choose the resolution you want.
Press OK.
Note
You can choose four different resolution settings for monochrome faxes and two for colour.
Monochrome
Standard
Fine
S.Fine
Photo
Suitable for most typed documents.
Good for small print and transmits a little slower than
Standard resolution.
Good for small print or artwork and transmits slower than Fine resolution.
Use when the document has varying shades of grey or is a photograph. This has the slowest transmission.
Colour
Standard
Fine
Suitable for most typed documents.
Use when the document is a photograph. The transmission time is slower than Standard resolution.
If you choose S.Fine or Photo and then use the Colour key to send a fax, the machine will send the fax using the Fine setting.
Dual access
(Monochrome only)
You can dial a number and start scanning the fax into memory—even when the machine is sending from memory, receiving faxes or printing PC data. The LCD shows the new job number and available memory.
The number of pages you can scan into the memory will vary depending on the data that is printed on them.
Note
If the Out of Memory message appears while scanning documents, press
Stop/Exit to cancel or Mono Start to send the scanned pages.
Real time transmission
5
When you are sending a fax, the machine will scan the documents into the memory before sending. Then, as soon as the phone line is free, the machine will start dialling and sending.
If the memory is full or you are sending a colour fax, the machine will send the document in real time (even if
Real Time TX
is set to Off).
Sometimes, you may want to send an important document immediately, without waiting for memory transmission. You can set
Real Time TX
to On for all documents or
Next Fax Only
for the next fax only.
5
24
Sending in real time for all faxes
a
Make sure you are in Fax mode .
b
Press Menu, 2, 2, 5.
5.Real Time TX
Realtime TX:On c
Press a or b to choose
Realtime TX:On
(or Realtime TX:Off).
Press OK.
5
Sending in real time for the next fax only
5 a
Make sure you are in Fax mode .
b
Press Menu, 2, 2, 5.
c
Press a or b to choose
Next Fax Only
.
Press OK.
d
Press a or b to choose Next Fax:On
(or Next Fax:Off).
Press OK.
Overseas Mode
If you are having difficulty sending a fax overseas due to possible interference on the phone line, we recommend that you turn on the Overseas mode. After you send a fax using this feature, the feature will turn itself off.
5 a
Make sure you are in Fax mode .
b
Load your document.
c
Press Menu, 2, 2, 7.
d
Press a or b to choose On (or Off).
Press OK.
Sending a fax
Delayed Faxing
(Monochrome only)
During the day you can store up to 50 faxes in the memory to be sent within 24-hours.
These faxes will be sent at the time of day you
5 a
Make sure you are in Fax mode .
b
Load your document.
c
Press Menu, 2, 2, 3.
3.Delayed Fax d
Do one of the following:
Press OK to accept the displayed time.
Enter the time you want the fax to be sent (in 24-hour format).
(For example, enter 19:45 for
7:45 PM.)
Press OK.
1.Doc 2.Memory
e
Do one of the following:
Press 1 to leave the document in the
ADF.
Press 2 to scan the document into the memory.
Note
The number of pages you can scan into the memory depends on the amount of data that is printed on each page.
5
25
Chapter 5
Delayed Batch Transmission
(Monochrome only)
5
Before sending the delayed faxes, your machine will help you economize by sorting all the faxes in the memory by destination and scheduled time. All delayed faxes that are scheduled to be sent at the same time to the same fax number will be sent as one fax to save transmission time.
a
Make sure you are in Fax mode .
b
Press Menu, 2, 2, 4.
c
Press a or b to choose On (or Off).
Press OK.
d
Press Stop/Exit.
Checking and cancelling waiting jobs
You can check which jobs are still waiting in the memory to be sent and cancel a job. (If there are no jobs, the LCD shows
No Jobs Waiting
.) a
Press Menu, 2, 6.
Any waiting jobs appear on the LCD.
b
Press a or b to scroll through the jobs and choose the job you want to cancel.
Press OK.
c
Do one of the following:
Press 1 to cancel the selected job.
Press 2 to exit without cancelling.
d
When you have finished, press
Stop/Exit.
5
Sending a fax manually
Manual transmission lets you hear the dialling, ringing and fax-receiving tones while sending a fax.
a
Make sure you are in Fax mode .
b
Load your document.
c
Pick up the handset of the machine and listen for a dial tone.
d
Dial the fax number you want to call.
e
When you hear the fax tone, press
Mono Start or Colour Start.
f
Replace the handset.
Sending a fax at the end of a conversation
5
At the end of a conversation you can send a fax to the other party before you both hang up.
a
Ask the other party to wait for fax tones
(beeps) and then to press the Start or
Send key before hanging up.
b
Make sure you are in Fax mode . c
Load your document.
d
Press Mono Start and Colour Start.
e
Replace the handset.
Out of Memory message
5
5
If you get an Out of Memory message while scanning the first page of a fax, press
Stop/Exit to cancel the fax.
If you get an Out of Memory message while scanning a subsequent page, you will have the option to press Mono Start to send the pages scanned so far, or to press
Stop/Exit to cancel the operation.
Note
If you get an Out of Memory message while faxing and you do not want to delete your stored faxes to clear the memory, you can send the fax in real time. (See
Real time transmission on page 24.)
26
6
Receiving a Fax
6
Receive modes
You must choose a receive mode depending on the external devices and telephone services you have on your line.
6
Choosing the Receive Mode
By default, your machine will automatically receive any faxes that are sent to it. The diagram below will help you choose the correct mode.
For more detailed information on the receive modes. See page 28.
6
6
Do you want to use the telephone features of your machine (if available) or an external telephone or external telephone answering device connected on the same line as the machine?
Yes
No
Are you using the voice message function of an external telephone answering device?
Fax Only
No
Do you want the machine to answer fax and telephone calls automatically?
No
Manual
Yes
Fax/Tel
External TAD
Yes
6
To choose or change your Receive
Mode
6
The LCD will display the current receive mode.
1 a
Press Menu 0, 1.
b
Press a or b to choose Fax Only,
Fax/Tel
, External TAD or Manual.
Press OK.
c
Press Stop/Exit.
1 Current receive mode
Fax
: Fax Only
27
Chapter 6
Using receive modes
Some receive modes answer automatically
(Fax Only and Fax/Tel). You may want to change the ring delay before using these
modes. (See Ring Delay on page 29.)
6
Fax only
Fax only mode will automatically answer every call. If the call is a fax your machine will receive it.
6
Fax/Tel
Fax/Tel mode helps you automatically manage incoming calls, by recognizing whether they are fax or voice calls and dealing with them in one of the following ways:
Faxes will be automatically received.
Voice calls will start the F/T ring to tell you to pick up the line. The F/T ring is a fast double ring made by your machine.
Also see F/T Ring Time (Fax/Tel mode only) and Ring Delay on page 29.
6
Manual
Manual mode turns off all automatic answering functions unless you are using the
BT Call sign feature.
To receive a fax in manual mode press
Mono Start or Colour Start when you hear fax tones (short repeating beeps). You can also use the Fax Detect feature to receive faxes by lifting a handset on the same line as the machine.
Also see Fax Detect on page 30.
6
External TAD
External TAD mode lets an external answering device manage your incoming calls. Incoming calls will be dealt with in one of the following ways:
Faxes will be automatically received.
Voice callers can record a message on the external TAD.
For more information see Connecting an external TAD (telephone answering
6
28
Receive mode settings
6
Ring Delay
The Ring Delay sets the number of times the machine rings before it answers in Fax Only or Fax/Tel mode. If you have external or extension phones on the same line as the machine or subscribe to the telephone company’s BT Call Sign service, choose the
maximum number of rings. (See Operation
from extension telephones on page 36 and
a
Press Menu, 2, 1, 1.
b
Press a or b to choose how many times the line rings before the machine answers (00-08 UK only).
Press OK.
If you choose 00, the line will not ring at all.
Note
The 00 setting is not available in Ireland.
c
Press Stop/Exit.
6
Receiving a Fax
F/T Ring Time
(Fax/Tel mode only)
If you set the Receive Mode to Fax/Tel, you need to decide how long the machine will signal you with its special pseudo/double-ring when you have a voice call. If it's a fax call, the machine receives the fax.
This pseudo/double-ring happens after the initial ringing from the phone company. Only the machine rings and no other phones on the same line will ring with the special pseudo/double-ring. However, you can still answer the call on any telephone.
a
Press Menu, 2, 1, 2.
b
Press a or b to choose how long the machine will ring to alert you that you have a voice call (20, 30, 40 or 70 seconds).
Press OK.
c
Press Stop/Exit.
Note
Even if the caller hangs up during the pseudo/double-ringing, the machine will continue to ring for the set time.
6
6
29
Chapter 6
Fax Detect
If Fax Detect is On:
The machine receives fax calls automatically, even if you lift the handset of an extension or external phone. When you see Receiving on the LCD or when you hear ‘chirps’ through the handset of an extension phone connected to another wall socket/phone socket, just replace the handset and your machine will do the rest.
6
If Fax Detect is Semi:
The machine will only receive the fax call if you answered it using the machine’s handset.
6
If Fax Detect is Off:
When you hear a fax tone through the handset, you have to press Mono Start or
Colour Start on the machine.
If you are not at your machine, press l 5 1 on
the extension phone. (See Operation from
extension telephones on page 36.)
6
Note
• If this feature is set to On, but your machine does not connect a fax call when you lift an extension or external phone handset, press the fax receive code l 5 1.
At the machine, press Mono Start or
Colour Start.
• If you send faxes from a computer on the same phone line and the machine intercepts them, set Fax Detect to Off.
a
Press Menu, 2, 1, 3.
b
Press a or b to choose On, Semi or
Off
.
Press OK.
c
Press Stop/Exit
6
Additional receiving operations
Printing a reduced incoming fax
6
If you choose On, the machine automatically reduces each page of an incoming fax to fit on one page of A4, Letter or Legal size paper.
The machine calculates the reduction ratio by using the page size of the fax and your Paper
Size setting (Menu, 1, 3).
a
Make sure you are in Fax mode .
b
Press Menu, 2, 1, 5.
5.Auto Reduction c
Use a or b to select On or Off.
Press OK.
d
Press Stop/Exit.
6
30
Receiving faxes into memory
6
As soon as the paper tray becomes empty during fax reception, the screen will display
No Paper Fed
, asking you to put paper in
the paper tray. (See Loading paper and other
media on page 11.) If you are unable to put
paper in the paper tray the following will happen:
If Memory Receive is On:
The machine will carry on receiving the fax, with the remaining pages being stored in memory, if enough memory is available.
Further incoming faxes will also be stored into memory until the memory is full. When the memory is full the machine will stop automatically answering calls. To print the faxes, put fresh paper in the tray.
6
If Memory Receive is Off:
The machine will carry on receiving the fax, with the remaining pages being stored in memory, if enough memory is available. The machine will then stop automatically answering calls until fresh paper is put in the paper tray. To print the last fax you received, put fresh paper in the tray.
6 a
Make sure you are in Fax mode .
b
Press Menu, 2, 1, 6.
c
Use a or b to select On or Off. Press
OK.
d
Press Stop/Exit.
Receiving a Fax
Receiving a fax at the end of a conversation
6
At the end of a conversation you can ask the other party to send you a fax before you both hang up.
a
Ask the other person to place the document in their machine and to press the Start or Send key.
b
When you hear the CNG tones (slowly repeating beeps), press Mono Start or
Colour Start.
c
Replace the handset.
Printing a fax from the memory
If you are using the Fax Storage feature
(Menu, 2, 5, 1), you can still print a fax from the memory when you are at your machine.
a
Press Menu, 2, 5, 3.
5.Remote Fax Opt
3.Print Document b
Press Mono Start.
6
6
31
32
7
Telephone and External devices
7
Voice Operations
Voice calls can be made either with the handset, an extension or external telephone, and by dialling manually or by using Quick-
Dial numbers.
7
Making a telephone call
a
To start a voice call, pick up the handset.
b
When you hear the dial tone, enter a number using the dial pad, One Touch,
Speed-Dial and Search.
c
To hang up, replace the handset.
7
Mute
If you want to put a call on hold, press the
Mute key. To release the call from hold pick up the handset. Picking up an extension handset will not release the call from hold.
7
Tone or pulse
If you have a Pulse dialing service, but need to send Tone signals (for example, for telephone banking), follow the instructions below: a
Pick up the handset.
b
Press # on the machine’s control panel.
Any digits dialled after this will send tone signals.
When you hang up, the machine will return to the Pulse dialling service.
7
Fax/Tel mode
When the machine is in Fax/Tel mode, it will use the F/T Ring Time (pseudo/doubleringing) to alert you to pick up a voice call.
If you are at the machine, you can lift the handset to answer.
If you are at an extension phone, you'll need to lift the handset during the F/T Ring Time and then press # 5 1 between the pseudo/double rings. If no one is on the line, or if someone wants to send you a fax, send the call back to the machine by pressing l 5 1.
7
Fax/Tel mode in Power Save condition
7
When the machine is in Fax/Tel mode and
F/T rings to tell you to pick up a voice call, you can only answer by picking up the machine’s handset .
If you answer before the machine F/T rings, you can also pick up the call at an external or extension phone.
Telephone services
Your machine supports the Caller ID subscriber telephone service that some telephone companies offer.
Features like Voice Mail, Call Waiting, Call
Waiting/Caller ID, answering services, alarm systems or other custom features on one phone line may create problems with the operation of your machine.
7
Caller ID (For U.K. and Ireland only)
7
The Caller ID feature lets you use the Caller
ID subscriber service offered by many local telephone companies. Call your telephone company for details. This service shows the telephone number, or name if it is available, of your caller as the line rings.
After a few rings, the LCD shows the telephone number of your caller (and name, if available). Once you answer a call, the Caller
ID information disappears from the LCD, but the call information stays stored in the Caller
ID memory.
You can see the first 16 characters of the number (or name).
The # Unavailable message means the call originated outside your Caller ID service area.
The # Withheld message means the caller has intentionally blocked transmission of information.
You can print a list of the Caller ID information
received by your machine. (See Printing
Note
Caller ID service varies with different carriers. Call your local telephone company to find out about the kind of service available in your area.
Telephone and External devices
Setting the Caller ID to ON
a
Press Menu, 2, 0, 4.
4.Caller ID b
Press a or b to choose On (or Off).
Press OK.
c
Press Stop/Exit.
7
Viewing Caller ID List
If Caller ID is set to On, your machine stores information for the last thirty calls in the Caller
ID list. You can view or print this list. When the thirty-first call comes in to the machine, it replaces information about the first call.
7 a
Press Menu, 2, 0, 4.
b
Press a or b to choose Display ID.
Press OK.
The Caller ID list will appear on the display. If no ID is stored, the beeper will sound and No Caller ID will appear on the display.
c
Press a or b to scroll through the Caller
ID memory to choose the Caller ID you want to view, and then press OK.
The LCD shows the caller's number or name and the date and time of the call.
d
Do one of the following:
To return to the Caller ID listing, press d.
To finish viewing, press Stop/Exit.
Printing Caller ID List
a
Press Menu, 2, 0, 4.
b
Press a or b to choose
Print Report
.
Press OK.
If no ID is stored, the beeper will sound and No Caller ID will appear on the
LCD.
c
Press Mono Start or Colour Start.
d
After printing has finished, press
Stop/Exit.
7
7
33
Chapter 7
Setting the Phone Line Type
7
If you are connecting the machine to a line that features a PBX or ISDN to send and receive faxes, it is also necessary to change the Phone Line Type accordingly by completing the following steps.
a
Press Menu, 0, 6.
0.Initial Setup
6.Phone Line Set b
Press a or b to select PBX, ISDN (or
Normal
). Press OK.
c
Press Stop/Exit.
PBX and TRANSFER
The machine is initially set to Normal, which lets the machine connect to a standard PSTN
(Public Switched Telephone Network) line.
However, many offices use a central telephone system or Private Branch
Exchange (PBX). Your machine can be connected to most types of PBX. The machine’s recall feature supports timed break recall only (TBR). TBR will work with most
PBX systems allowing you to gain access to an outside line, or transfer calls to another extension. The feature works when Tel/R is pressed.
7
Note
You can program a Tel/R key press as part of a number stored in a Speed-Dial location.
When programming the Speed-Dial number (Menu, 2, 3, 1 or 2, 3, 2) press
Tel/R first (the screen displays “!”) then enter the telephone number. If you do this, you do not need to press Tel/R each time before you dial using a Speed-Dial location.
(See Storing numbers on page 40.)
However, if PBX is not selected in the
Phone Line Type setting, you cannot use the Speed-Dial number that Tel/R press is programmed into.
34
BT Call Sign (For U.K. only)
This machine feature lets you use the BT Call
Sign subscriber service which allows you to have at least two separate telephone numbers on one phone line. Each phone number has its own distinctive ringing pattern, so you know which phone number is ringing. This is one way you can have a separate phone number for your machine.
Your machine has a BT Call Sign compatible distinctive ringing function, allowing you to dedicate a second phone number (on the same phone line) just for receiving faxes.
Note
• You can switch BT Call Sign off temporarily, then turn it back on. When you get a new fax number, make sure you reset this function. This machine will automatically answer incoming calls that use your new fax number.
• When you set the BT Call Sign feature to
ON, the receive mode is set to Manual automatically. Manual mode will not respond to incoming telephone calls, since the number you use for telephone calls will use the normal ring pattern.
To enable the machine to work with BT
Call Sign (With your external phone only)
7 a
Press Menu, 2, 0, 3.
0.Miscellaneous
3.BT Call Sign b
Press a or b to choose On (or Off).
Press OK.
c
Press Stop/Exit.
Note
If you turn off BT Call Sign, the receive mode stays in Manual. You will need to
set receive mode again. (See Choosing
7
Connecting an external
TAD (telephone answering device)
7
You may choose to connect an external answering device. However, when you have an
external TAD on the same telephone line as the machine, the TAD answers all calls and the machine ‘listens’ for fax calling (CNG) tones. If it hears them, the machine takes over the call and receives the fax. If it does not hear CNG tones, the machine lets the TAD continue playing your outgoing message so your caller can leave you a voice message.
The TAD must answer within four rings (the recommended setting is two rings). The machine cannot hear CNG tones until the TAD has answered the call, and with four rings there are only 8 to 10 seconds of CNG tones left for the fax ‘handshake’. Make sure you carefully follow the instructions in this guide for recording your outgoing message. We do not recommend using the toll saver feature on your external answering machine if it exceeds five rings.
Note
• If you do not receive all your faxes, cut the
Ring Delay setting on your external TAD.
• Do not connect a TAD elsewhere on the same phone line.
1
1
1 TAD
When the TAD answers a call, the LCD shows
Ext. Tel in Use.
Improper Setup
Do not connect a TAD elsewhere on the same phone line.
Telephone and External devices
Connections
The external TAD must be connected as shown in the previous illustration.
a
Set your external TAD to one or two rings. (The machine's Ring Delay setting does not apply.) b
Record the outgoing message on your external TAD.
c
Set the TAD to answer calls.
d
Set the Receive Mode to
External TAD
7
Recording an outgoing message (OGM) on an external TAD
Timing is important in recording this message. The message sets up the ways to handle both manual and automatic fax reception.
a
Record 5 seconds of silence at the beginning of your message. (This allows your machine time to listen for the fax
CNG tones of automatic transmissions before they stop.) b
Limit your speaking to 20 seconds.
Note
We recommend beginning your OGM with an initial 5-second silence because the machine cannot hear fax tones over a resonant or loud voice. You may try omitting this pause, but if your machine has trouble receiving, then you must rerecord the OGM to include it.
7
7
35
Chapter 7
Multi-line connections (PBX)
7
We suggest you ask the company who installed your PBX to connect your machine.
If you have a multi line system we suggest you ask the installer to connect the unit to the last line on the system. This prevents the machine being activated each time the system receives telephone calls. If all incoming calls will be answered by a switchboard operator we recommend that you set the Receive Mode to Manual.
We cannot guarantee that your machine will operate properly under all circumstances when connected to a PBX. Any difficulties with sending or receiving faxes should be reported first to the company who handles your PBX.
Note
Make sure the Phone Line Type is set to
PBX. (See Setting the Phone Line
External and extension phones
Connecting an external or extension telephone
You can connect a separate telephone to your machine as shown in the diagram below.
7
1
2
1 Extension telephone
2 External telephone
When you are using an external phone, the
LCD shows Ext. Tel in Use.
Operation from extension telephones
If you answer a fax call on an extension or an external telephone plugged into the correct socket on the machine, you can make your machine take the call by using the Fax
Receive Code. When you press the Fax
Receive Code l 5 1, the machine starts to receive the fax.
If the machine answers a voice call and pseudo/double-rings for you to take over, use the Telephone Answer Code # 5 1 to take the
call at an extension phone. (See F/T Ring
Time (Fax/Tel mode only) on page 29.)
7
7
36
If you answer a call and no one is on the line:
7
You should assume that you're receiving a manual fax.
Press l 5 1 and wait for the chirp or until the
LCD shows Receiving, and then hang up.
Note
You can also use the Fax Detect feature to make your machine automatically take the
call. (See Fax Detect on page 30.)
Using extension telephones
(For U.K. only)
7
Your premises may already be wired with parallel extension telephones, or you may plan to add extension telephones to your line, as well as your machine. While the simplest arrangement is a straightforward parallel connection, there are some problems with this arrangement, the most obvious of which is inadvertent interruption of a facsimile transmission caused by someone picking up an extension telephone to make an outgoing call. Also, fax receive code may not operate reliably in such a simple configuration.
This machine may also be set to make a delayed transmission (i.e. a transmission at a pre-set time). This pre-set job may coincide with someone picking up an extension handset.
These problems can easily be eliminated, if you arrange modification of your extension wiring circuit, such that extension devices are connected ‘downstream’ of your machine in a master/slave configuration (see figure 2 on
page 37). In this configuration the machine
can always detect whether a telephone is in use. Thus it will not attempt to seize the line during that time. This is known as ‘telephone off-hook detection.’
The inadvisable configuration is shown in
figure 1 on page 37, and the recommended
master/slave configuration is shown in figure 2.
Telephone and External devices
This new connection configuration can be arranged by contacting BT, Kingston upon
Hull Telecommunications, your PBX maintainer or a qualified telephone installation company as appropriate. Simply explained, the extension telephone circuit should be terminated on a normal modular plug (BT 431A style), which in turn should be put into the modular socket of the white ‘T’shaped connector provided as part of the line cord assembly.
Inadvisable connection of extension sockets (Fig. 1.)
1 2 1
3
7
FAX
1 Extension socket
2 Master socket
3 Incoming line
Recommended connection of extension sockets (Fig. 2.)
1 1 2
3
7
FAX
1 Extension socket
2 Master socket
3 Incoming line
The fax machine must be plugged into master socket.
Note
These phones are now connected as
external devices (see Connecting an external or extension
telephone on page 36), because they are
connected to the fax machine via the Tconnector.
37
7
Chapter 7
Using a cordless external telephone
Once the base unit of the cordless telephone has been connected to the same telephone
line as the machine (see External and
extension phones on page 36), it is easier to
answer calls during the Ring Delay if you carry the cordless handset around with you.
If you let the machine answer first, you will have to go to the machine so you can press
Tel/R to send the call to the cordless handset.
7
Using remote codes
Fax receive code
If you answer a fax call on an extension or external telephone, you can tell your machine to receive it by dialling the fax receive code l 5 1.
Wait for the chirping sounds then replace the
handset. (See Fax Detect on page 30.) Your
caller will have to press Start to send the fax.
7
Telephone answer code
If you receive a voice call and the machine is in F/T mode, it will start to sound the F/T
(double) ring after the initial ring delay. If you pick up the call on an extension phone you can turn the F/T ring off by pressing # 5 1
(make sure you press this between the rings).
7
Changing the remote codes
If you want to use Remote Activation, you have to turn on the remote codes. The preset
Fax Receive Code is l 5 1. The preset Telephone
Answer Code is # 5 1. If you want to, you can replace them with your own codes.
7 a
Press Menu, 2, 1, 4.
1.Setup Receive
4.Remote Codes b
Press a or b to choose On (or Off).
Press OK.
c
Enter the new Fax Receive Code.
Press OK.
d
Enter the new Telephone Answer Code.
Press OK.
e
Press Stop/Exit.
Note
• If you are always disconnected when accessing your external TAD remotely, try changing the Fax Receive Code and
Telephone Answer Code to another threedigit code using the numbers 0-9, l, #.
• Remote Codes might not work with some telephone systems.
7
38
8
Dialling and storing numbers
How to Dial
Manual dialling
Press all of the digits of the fax number.
8
8
Speed-Dialling
a
Press Search/Speed Dial, the # (hash) key, and then the two digit Speed-Dial number.
8
8
One-Touch Dialling
Press the One-Touch key that stores the number you want to call.
To dial One-Touch numbers 6 to 10, hold down Shift as you press the One-Touch key.
8
Two-digit number
Note
If the LCD shows Not Registered when you enter a One-Touch number or a
Speed-Dial number, a number has not been stored at this location.
8
39
Chapter 8
Search
You can search for names you have stored in the One-Touch and Speed-Dial memories.
Press Search/Speed Dial and the menu keys to search numerically or use the dial pad and then the menu keys to search alphabetically.
8
1
2
1 To search numerically.
2 To search alphabetically, you can use the dial pad to enter the first letter of the name you are looking for.
Fax Redial
If you are sending a fax manually and the line is busy, press Redial/Pause, and then press
Mono Start or Colour Start to try again. If you want to make a second call to the last number dialled, you can save time by pressing Redial/Pause and Mono Start or
Colour Start.
Redial/Pause only works if you dialled from the control panel.
If you are sending a fax automatically and the line is busy, the machine will automatically redial up to three times at five minute intervals.
8
Storing numbers
You can set up your machine to do the following types of easy dialling: One-Touch,
Speed-Dial and Groups for broadcasting faxes. When you dial a Quick-Dial number, the LCD shows the name, if you stored it, or the number.
8
Note
If you lose electrical power, the Quick-Dial numbers that are in the memory will not be lost.
Storing a pause
8
Press Redial/Pause to put a 3.5-second pause between numbers. If you are dialling overseas, you can press Redial/Pause as many times as needed to increase the length of the pause.
40
Storing One-Touch Dial numbers
Your machine has 5 One-Touch keys where you can store 10 fax or phone numbers for automatic dialling. To access numbers 6 to
10, hold down Shift as you press the
One-Touch key.
a
Press Menu, 2, 3, 1.
b
Press the One-Touch key where you want to store a number.
c
Enter the number (up to 20 digits).
Press OK.
d
Do one of the following:
Enter the name using the dial pad
(up to 16 characters). (To help you
Press OK.
To store the number without a name, press OK. e
Do one of the following:
To store another One-Touch
To finish storing One-Touch numbers, press Stop/Exit.
8
Dialling and storing numbers
Storing Speed-Dial numbers
8
You can store up to 100 two-digit Speed-Dial locations with a name. When you dial you will only have to press a few keys (For example:
Search/Speed Dial #, the two-digit number, and Mono Start or Colour Start).
a
Press Menu, 2, 3, 2.
b
Use the dial pad to enter a 2-digit
Speed-Dial location number (00-99).
Press OK.
c
Enter the fax or telephone number (up to
20 digits).
Press OK.
d
Do one of the following:
Enter the name (up to 16 characters) using the dial pad.
Press OK. (To help you enter letters,
see Entering Text on page 102.)
To store the number without a name, press OK.
e
Do one of the following:
To store another Speed-Dial
To finish the setting, press
Stop/Exit.
8
41
Chapter 8
Changing One-Touch and
Speed-Dial numbers
If you try to store a One-Touch or Speed-Dial number where a number has already been stored, the LCD will show the name or number that has been stored there, and will ask you to do one of the following:
Press 1 to change the stored number.
#05:MIKE
1.Change
2.Exit
Press 2 to exit without making a change.
If you chose 1, you will be able to change the stored number and name, or enter a new one.
Follow the instructions below: a
Enter a new number. Press OK.
b
Enter a new name. Press OK.
To change a character, use d or c to position the cursor under the character you want to change, then press
Clear/Back. Re-enter the character.
8
Setting up Groups for broadcasting
If you regularly want to send the same fax message to many fax numbers you can set up a Group. Groups are stored on a
One-Touch key or a Speed-Dial number.
Each group uses up a One-Touch key or a
Speed-Dial location. You can then send the fax message to all the numbers stored in a
Group just by pressing a One-Touch key or entering a Speed-Dial number, and then pressing Mono Start.
Before you can add numbers to a Group, you need to store them as One-Touch or Speed-Dial numbers.
You can have up to six small Groups, or you can assign up to 99 numbers to one large Group.
a
Press Menu, 2, 3, 3.
3.Setup Groups b
Choose an empty location where you want to store the Group in one of the following ways:
Press a One-Touch key. c
Use the dial pad to enter a Group number (1 to 6).
Press OK.
Press Search/Speed Dial and enter a two-digit location.
Press OK.
Setup Group:G01 d
To add One-Touch or Speed-Dial numbers to the Group follow the instructions below:
For example, for One-Touch number
6 press One-Touch key 6.
For example, for Speed-Dial location
09, press Search/Speed Dial, and then press 0 9 on the dial pad.
The LCD will display your chosen
One-Touch numbers with a l, and
Speed-Dial numbers with a # as shown in the illustration.
G01: l06 #09
8
42
e
Press OK when you have finished adding numbers.
f
Use the dial pad to enter a name for the
Group.
Press OK.
g
Press Stop/Exit.
Note
You can easily print a list of all your
Speed-Dial numbers. Numbers that are part of a group will be marked in the
GROUP column. (See How to print a
Combining Quick-Dial numbers
8
You can combine more than one Quick-Dial number when you dial. This feature may be useful if you need to dial an access code for a cheaper rate long distance carrier.
For example, you might have stored ‘555’ on
Speed-Dial #03 and ‘7000’ on Speed-Dial
#02. You can use them both to dial ‘555-7000’ if you press the following keys:
Search/Speed Dial, #03,
Search/Speed Dial, #02, and Mono Start or
Colour Start.
Numbers can be added manually by entering them on the dial pad:
Search/Speed Dial, #03, 7, 0, 0, 1 (on the dial pad), and Mono Start or Colour Start.
This would dial ‘555-7001’. You can also add a pause by pressing the Redial/Pause key.
Dialling and storing numbers
8
43
44
9
Remote fax options
Remote fax options are not available for
colour fax.
You can only use one remote fax option at a time.
Fax Forwarding
The fax forwarding feature lets you automatically forward your received faxes to another machine. If you choose
Backup Print:On
the machine will also print the fax (this is a safety feature in case there is a power failure).
a
Press Menu, 2, 5, 1.
1.Forward/Store b
Press a or b to choose Fax Forward.
Press OK.
The LCD will ask you to enter the fax number you want your faxes to be forwarded to.
c
Enter the forwarding number (up to 20 digits).
Press OK.
d
Press a or b to choose
Backup Print:On
or
Backup Print:Off
.
Press OK.
9
Note
When Fax Forwarding is turned on your machine will only receive monochrome faxes into memory. Colour faxes will not be received, unless the sending machine converts them to monochrome before sending. e
Press Stop/Exit.
Fax Storage
The fax storage feature lets you store your received faxes in the machine’s memory. You can retrieve stored fax messages from a fax machine at another location using the remote
retrieval commands. (See Retrieving fax
messages on page 46.) Your machine will
automatically print a copy of the stored fax.
a
Press Menu, 2, 5, 1.
1.Forward/Store b
Press a or b to choose Fax Storage.
Press OK.
c
Press Stop/Exit.
Note
If Fax Storage is turned on your machine cannot receive a colour fax unless the sending machine converts it to monochrome.
9
9
Changing Remote Fax
Options
9
If received faxes are left in your machine's memory when you change the remote fax options, the LCD will ask you one of the following messages:
Erase All Doc?
1.Yes 2.No
Print All Fax?
1.Yes 2.No
If you press 1, faxes in the memory will be erased or printed before the setting changes. If a backup copy has already been printed it will not be printed again.
If you press 2, faxes in the memory will not be erased or printed and the setting will be unchanged.
Turning off Remote Fax
Options
a
Press Menu, 2, 5, 1.
1.Forward/Store b
Press a or b to choose Off.
Press OK.
c
Press Stop/Exit.
Note
The LCD will give you more options if there are received faxes still in your
machine’s memory. (See Changing
Remote Fax Options on page 45.)
9
Remote fax options
Remote Retrieval
You can call your machine from any touch tone telephone or fax machine, then use the remote access code and remote commands to retrieve fax messages.
9
Setting a Remote Access
Code
The remote access code lets you access the remote retrieval features when you are away from your machine. Before you use the remote access and retrieval features, you have to set up your own code. The factory default code is inactive code (---l).
a
Press Menu, 2, 5, 2.
2.Remote Access b
Enter a three-digit code using numbers
0-9, l, or #.
Press OK. (The preset ‘l’ cannot be changed.) c
Press Stop/Exit.
Note
Do not use the same code as your fax receive code (l 5 1) or telephone answer
code (# 5 1). (See Operation from
extension telephones on page 36.)
You can change your code at any time by entering a new one. If you want to make your
code inactive, press Clear/Back in step b to
restore the inactive setting (---l) and press OK.
9
9
45
Chapter 9
Using your Remote Access
Code
9 a
Dial your fax number from a telephone or another fax machine using touch tone.
b
When your machine answers, enter your remote access code (3 digits followed by l).
c
The machine signals if it has received messages:
1 long beep — Fax messages
No beeps — No messages d
When the machine gives two short beeps, enter a command.
The machine will hang up if you wait longer than 30 seconds to enter a command.
The machine will beep three times if you enter an invalid command.
e
Press 9 0 to stop Remote Access when you have finished.
f
Hang up.
Note
If your machine is set to Manual mode and you want to use the remote retrieval features, wait about 2 minutes after it starts ringing, and then enter the remote access code within 30 seconds.
Retrieving fax messages
a
Dial your fax number.
b
When your machine answers, enter your remote access code (3 digits followed by l). If you hear one long beep, you have messages.
c
When you hear two short beeps, press 9 6 2.
d
Wait for the long beep, use the dial pad to enter the number (up to 20 digits) of the remote fax machine where you want your fax messages forwarded followed by # #.
Note
You cannot use l and # as dial numbers.
However, press # if you want to create a pause.
e
Press 9 0 to reset the machine when you have finished.
f
Hang up after you hear your machine beep. Your machine will call the other fax machine, which will then print your fax messages.
9
46
Changing your Fax
Forwarding number
You can change the default setting of your fax forwarding number from another telephone or fax machine using touch tone.
a
Dial your fax number.
b
When your machine answers, enter your remote access code (3 digits followed by l) at once. If you hear one long beep, you have messages.
c
When you hear two short beeps, press 9 5 4.
d
Wait for the long beep, and then use the dial pad to enter the new number
(up to 20 digits) of the remote fax machine where you want your fax messages forwarded followed by # #.
Note
You cannot use l and # as dial numbers.
However, press # if you want to create a pause.
e
Press 9 0 when you have finished.
f
Hang up after you hear your machine beep.
9
Remote fax options
9
47
Chapter 9
Remote fax commands
Follow the commands below to access features when you are away from the machine. When you call the machine and enter your remote access code (3 digits followed by l), the system will give two short beeps and you must enter a remote command.
9
Remote commands
95 Change the Fax Forwarding or Fax
Storage settings
1 OFF
Operation details
2 Fax Forwarding
4 Fax Forwarding number
6 Fax Storage
You can choose Off after you have retrieved or erased all your messages.
If you hear one long beep, the change has been accepted.
If you hear three short beeps, you cannot change it because something has not been set up (for example, registering a
Fax Forwarding number). You can register your Fax
Forwarding number by entering 4. (See Changing your Fax
Forwarding number on page 47.)
96 Retrieve a fax
2 Retrieve all faxes
3 Erase faxes from the memory
Enter the number of a remote fax machine to receive stored
fax messages. (See Retrieving fax messages on page 46.)
If you hear one long beep, fax messages have been erased from the memory.
97 Check the receiving status
1 Document You can check whether your machine has received any faxes. If yes, you will hear one long beep. If no, you will hear three short beeps.
98 Change the Receive Mode
1 External TAD
2 Fax/Tel
3 Fax Only
90 Exit
If you hear one long beep, your change has been accepted.
Pressing 9 0 will allow you to exit Remote Retrieval. Wait for the long beep, then replace the handset.
48
10
Printing Reports
10
Fax reports
You need to set up the Transmission
Verification Report and Journal Period using the Menu key.
10
Transmission Verification
Report
You can use the Transmission Report as proof that you sent a fax. This report lists the time and date of transmission and whether the transmission was successful (OK). If you choose On or On+Image, the report will print for every fax you send.
If you send a lot of faxes to the same place, you may need more than the job numbers to know which faxes you must send again.
Choosing On+Image or Off+Image will print a section of the fax's first page on the report to help you remember.
When the Verification Report is turned Off or
Off+Image
, the Report will only print if there is a transmission error, with NG in the
RESULT column.
a
Press Menu, 2, 4, 1.
b
Press a or b to choose Off+Image,
On
, On+Image or Off.
Press OK.
c
Press Stop/Exit.
10
Fax Journal (activity report)
10
You can set the machine to print a journal at specific intervals (every 50 faxes, 6, 12 or 24 hours, 2 or 7 days). If you set the interval to
Off
, you can still print the report by following
the steps in How to print a report on page 50.
The default setting is Every 50 Faxes.
a
Press Menu, 2, 4, 2.
b
Press a or b to choose an interval.
Press OK.
(If you choose 7 days, the LCD will ask you to choose the first day for the 7-day countdown.)
6, 12, 24 hours, 2 or 7 days
The machine will print the report at the chosen time and then erase all jobs from its memory. If the machine's memory becomes full with
200 jobs before the time you chose has passed, the machine will print the Journal early and then erase all jobs from the memory. If you want an extra report before it is due to print, you can print it without erasing the jobs from the memory.
Every 50 Faxes
The machine will print the Journal when the machine has stored 50 jobs.
c
Enter the time to start printing in 24-hour format.
Press OK.
(For example: enter 19:45 for 7:45 PM.) d
Press Stop/Exit.
10
49
Chapter 10
Reports
The following reports are available:
1.XMIT Verify
Prints a Transmission Verification Report for your last transmission.
2.Help List
A help list about how to quickly program your machine.
3.Quick-Dial
Lists names and numbers stored in the
One-Touch and Speed-Dial memory, in numerical order.
4.Fax Journal
Lists information about the last incoming and outgoing faxes. (TX: Transmit.)
(RX: Receive.)
5.User Settings
Lists your settings.
How to print a report
a
Press Menu, 4.
b
Do one of the following:
Press a or b to choose the report you want.
Press OK.
Enter the number of the report you want to print. For example, press 2 to print the Help List.
c
Press Mono Start.
10
10
50
11
Polling
11
Polling lets you set up your machine so other people can receive faxes from you, but they pay for the call. It also lets you call somebody else’s fax machine and receive a fax from it, so you pay for the call. The polling feature needs to be set up on both machines for this to work. Not all fax machines support polling.
Polling receive
Polling receive lets you call another fax machine to receive a fax.
Setup for polling receive
a
Make sure you are in Fax mode .
b
Press Menu, 2, 1, 7.
7.Polling RX c
Press a or b to choose Standard.
Press OK.
d
Enter the fax number you are polling.
e
Press Mono Start or Colour Start.
11
11
Setup to receive polling with a secure code
11
Secure Polling restricts who can retrieve the documents you set up to be polled.
Secure Polling only works with Brother fax machines. If you want to retrieve a fax from a secured Brother machine you have to enter the secure code.
a
Make sure you are in Fax mode .
b
Press Menu, 2, 1, 7.
7.Polling RX c
Press a or b to choose Secure.
Press OK.
d
Enter a four-digit secure code.
Press OK.
This is the security code of the fax machine you are polling.
e
Enter the fax number you are polling.
f
Press Mono Startor Colour Start.
11
51
Chapter 11
Setup for delayed polling receive
Delayed polling lets you set the machine to begin polling receive at a later time. You can only set up one delayed polling operation.
11 a
Make sure you are in Fax mode .
b
Press Menu, 2, 1, 7.
7.Polling RX c
Press a or b to choose Timer.
Press OK.
d
Enter the time (in 24-hour format) you want to start polling.
Press OK.
For example, enter 21:45 for 9:45 PM.
e
Enter the fax number you are polling.
f
Press Mono Start or Colour Start.
The machine makes the polling call at the time you entered.
Sequential polling
The machine can request documents from several fax machines in one operation.
11 a
Make sure you are in Fax mode .
b
Press Menu, 2, 1, 7.
7.Polling RX c
Press a or b to choose Standard,
Secure
or Timer.
Press OK.
d
Do one of the following:
If you chose Standard, go to
If you chose Secure, enter a fourdigit number, press OK, go to
If you chose Timer, enter the time
(24-hour format) you want to begin
polling and press OK, go to step e.
e
Specify the destination fax machines, which you wish to poll by using One-
Touch, Speed-Dial, Search, a Group or the dial pad. You must press OK between each location.
f
Press Mono Start or Colour Start.
The machine polls each number or group in turn for a document.
Press Stop/Exit while the machine is dialling to cancel the polling process.
To cancel all sequential polling receive jobs,
see Checking and cancelling waiting
52
Polled transmit
(Monochrome only)
Polled Transmit is when you set up your machine to wait with a document so another fax machine can call and retrieve it.
11
Setup for polled transmit
11 a
Make sure you are in Fax mode .
b
Load your document.
c
Press Menu, 2, 2, 6.
6.Polled TX d
Press a or b to choose Standard.
Press OK.
1.Doc 2.Memory
e
Do one of the following:
Press 1 to leave the documents waiting in the ADF.
If you want to use the ADF before your machine is polled, you must cancel the job.
Press 2 to scan the document into the memory.
f
The LCD shows:
Next
1.Yes 2.No
g
Press 2 and press Mono Start.
Polling
Setup for polled transmit with secure code
11
Secure Polling restricts who can retrieve the documents you set up to be polled.
Secure Polling only works with Brother fax machines. If another person wants to retrieve a fax from your machine they will have to enter the secure code.
a
Make sure you are in Fax mode .
b
Load your document.
c
Press Menu, 2, 2, 6.
6.Polled TX d
Press a or b to choose Secure.
Press OK.
e
Enter a four-digit number.
Press OK.
1.Doc 2.Memory
f
Do one of the following:
Press 1 to leave the documents waiting in the ADF.
If you want to use the ADF before your machine is polled, you must cancel the job.
Press 2 to scan the document into the memory.
g
The LCD shows:
Next
1.Yes 2.No
h
Press 2 and press Mono Start.
11
53
54
Chapter 11
Section III
Copy
Making copies
III
56
12
Making copies
How to copy
Entering Copy mode
Press (Copy) to enter Copy mode.
The default setting is Fax. You can change the number of seconds or minutes that the
machine stays in Copy mode. (See Mode
12
12
The LCD shows the default copy setting:
Making multiple copies
a
Make sure you are in Copy mode .
b
Load your document.
c
Use the dial pad to enter the number of copies (up to 99).
d
Press Mono Start or Colour Start.
Note
To sort your copies, press Copy Options.
(See Sorting copies using the ADF
(Monochrome only) on page 60.)
Stop copying
12
To stop copying, press Stop/Exit.
12
1
1 Copy Ratio
2 Quality
3 No of Copies
2
Making a single copy
3 a
Make sure you are in Copy mode .
b
Load your document.
c
Press Mono Start or Colour Start.
12
12
Making copies
Copy options
When you want to quickly change the copy settings temporarily for the next copy, use the
Copy keys.
12
The machine returns to its default settings
30 seconds after it finishes copying, or if the mode timer returns the machine to Fax mode.
Press Menu selection/
Quality
Options Page
Normal
Fast
Enlarge/
Reduce
Paper Type
Best
50%
/69%/78%/83%/
93%
/97%/100%/
104%
/142%/186%/
198%/200%
/
Custom(25-400%)
Plain Paper
Inkjet Paper
Brother Photo
Other Photo
Transparency
Paper Size Letter
Legal
A4
A5
10(W)x15(H)cm
Brightness
- nnonn +
Stack/Sort Stack
Sort
Page Layout Off(1 in 1)
2 in 1 (P)
No . of
Co pi es
2 in 1 (L)
4 in 1 (P)
4 in 1 (L)
No. of Copies:01
(01 - 99)
Note
You can save the copy settings you use most often by setting them as default. You can find instructions on how to do this in the section for each feature.
12
57
Chapter 12
Changing copy speed and quality
You can choose from a range of quality settings. The default setting is Normal.
To temporarily change the quality settings, follow the instructions below:
12
Press and a or b to choose
Quality
Normal
Normal is the recommended mode for ordinary printouts.
This produces good copy quality with good copy speed.
Fast
Best
Fast copy speed and lowest ink consumption. Use to save time printing documents to be proofread, large documents or many copies.
Use best mode to copy precise images such as photographs. This provides the highest resolution and the slowest speed.
a
Make sure you are in Copy mode .
b
Load your document.
c
Use the dial pad to enter the number of copies (up to 99).
Press Copy Options and a or b to choose Quality.
Press OK.
d
Press a or b to choose Normal, Fast or Best. Press OK.
e
Press Mono Start or Colour Start.
To change the default setting, follow the instructions below: a
Press Menu, 3, 1.
1.Quality
b
Press a or b to choose Normal, Fast or Best. Press OK.
c
Press Stop/Exit.
Enlarging or reducing the image copied
You can select the following enlargement or reduction ratios:
Custom(25-400%)
allows you to enter a ratio from 25% to 400%.
12
Press and a or b to choose
Enlarge/Reduce
Custom(25-400%)
200%
198% 10x15cm iA4
186% 10x15cm iLTR
142% A5 iA4
104% EXE iLTR
100%
97% LTR iA4
93% A4 iLTR
83% LGL iA4
78% LGL iLTR
69% A4 iA5
50%
To enlarge or reduce the next copy follow the instructions below: a
Make sure you are in Copy mode .
b
Load your document.
c
Use the dial pad to enter the number of copies (up to 99).
d
Press Copy Options and a or b to choose Enlarge/Reduce.
Press OK.
58
e
Do one of the following:
Use a or b to choose the enlargement or reduction ratio you want.
Press OK.
Use a or b to choose
Custom(25-400%)
. Press OK. Use the dial pad to enter an enlargement or reduction ratio from 25% to 400%.
(For example, press 5 3 to enter
53%
.)
Press OK.
f
Press Mono Start or Colour Start.
Note
Page Layout Options 2 in 1(P), 2 in 1(L),
4 in 1(P) or 4 in 1(L) are not available with Enlarge/Reduce.
Making N in 1 copies
12
The N in 1 copy feature can help you save paper by letting you copy two or four pages onto one printed page.
Important
Please make sure paper size is set to
Letter or A4.
You cannot use the Enlarge/Reduce setting with the N in 1.
N in 1 colour copies are not available.
(P) means Portrait and (L) means
Landscape.
12 a
Make sure you are in Copy mode .
b
Load your document.
c
Use the dial pad to enter the number of copies (up to 99).
d
Press Copy Options and a or b to select Page Layout.
Press OK.
Making copies e
Press a or b to select Off(1 in 1),
2 in 1 (P)
, 2 in 1 (L),
4 in 1 (P)
, or 4 in 1 (L).
Press OK.
f
Press Mono Start to scan the document.
Note
If photo paper is selected as the paper type setting for N in 1 copies, the images will be printed as if plain paper had been selected.
Place your document face down in the direction shown below:
2 in 1 (P)
2 in 1 (L)
4 in 1 (P)
4 in 1 (L)
12
59
Chapter 12
Sorting copies using the ADF
(Monochrome only)
12
You can sort multiple copies. Pages will be stacked in the order 1 2 3, 1 2 3, 1 2 3, and so on.
a
Make sure you are in Copy mode .
b
Load your document.
c
Use the dial pad to enter the number of copies (up to 99).
d
Press or Copy Options and a or b to select Stack/Sort.
Press OK.
e
Press a or b to select Sort.
Press OK.
f
Press Mono Start.
Adjusting Brightness,
Contrast and Colour
Brightness
To temporarily change the brightness setting, follow the instructions below:
12 a
Make sure you are in Copy mode . b
Load your document.
c
Use the dial pad to enter the number of copies (up to 99).
d
Press Copy Options and a or b to select Brightness.
Press OK.
nnonn+ e e
Press a or b to make the copy lighter or darker.
Press OK.
f
Press Mono Start or Colour Start.
To change the default setting follow the instructions below: a
Press Menu, 3, 2.
b
Press a or b to make the copy lighter or darker.
Press OK.
c
Press Stop/Exit.
12
60
Contrast
Adjust the contrast to help an image look sharper and more vivid.
To change the default setting follow the instructions below: a
Press Menu, 3, 3.
3.Contrast
b
Press a or b to change the contrast.
Press OK.
c
Press Stop/Exit.
12
Colour saturation
The colour saturation can only be changed through the default setting.
12 a
Press Menu, 3, 4.
4.Color Adjust b
Press a or b to select 1.Red,
2.Green
or 3.Blue.
Press OK.
c
Press a or b to change the colour saturation.
Press OK.
d
Do one of the following:
Return to b to select the next colour.
Press Stop/Exit.
Making copies
Paper options
Paper type
If you are copying on special paper, be sure to select the type of paper you are using so you will get the best print quality.
12 a
Make sure you are in Copy mode . b
Load your document.
c
Use the dial pad to enter the number of copies (up to 99).
d
Press Copy Options and a or b to select Paper Type.
Press OK.
e
Press a or b to select the type of paper you are using (Plain Paper,
Inkjet Paper
, Brother Photo,
Other Photo
or Transparency).
Press OK.
f
Press Mono Start or Colour Start.
Note
To change the default paper type setting
12
12
61
Chapter 12
Paper size
If copying on paper other than A4 size, you will need to change the paper size setting.
You can copy on Letter, Legal, A4, A5 or
Photo Card 10(W) × 15(H)cm paper.
12 a
Make sure you are in Copy mode .
b
Load your document.
c
Use the dial pad to enter the number of copies (up to 99).
d
Press Copy Options and a or b to select Paper Size.
Press OK.
e
Press a or b to select the size of paper you are using Letter, Legal, A4, A5 or 10(W) x 15(H)cm.
Press OK.
f
Press Mono Start or Colour Start.
Note
To change the default paper type setting
62
Section IV
Software
Software features
IV
64
13
Software features
The CD-ROM includes the Software User’s
Guide for features available when connected to a computer (for example, printing and scanning). The guide has easy to use links that, when clicked, will take you directly to a particular section.
You can find information on these features:
Printing
Scanning
ControlCenter3 (for Windows
®
)
ControlCenter2 (for Macintosh
®
)
Remote Setup
Faxing from your computer
How to read the HTML User’s Guide
This is a quick reference for using the HTML
User’s Guide.
13
(For Windows
®
)
Note
If you have not installed the software, see
Viewing Documentation on page 2.
a
From the Start menu, point to Brother,
MFC-3360C from the programs group, then click User’s Guide.
b
Click SOFTWARE USER’S GUIDE from the top menu.
c
Click the heading you would like to read from the list at the left of the window.
(For Macintosh
®
) a
Make sure your Macintosh
®
is turned on. Insert the Brother CD-ROM into your
CD-ROM drive. b
Double-click your Documentation icon.
c
Double-click your language folder and then double-click the top page of the
HTML file.
d
Click SOFTWARE USER’S GUIDE in the top menu, and then click the heading you would like to read from the list at the left of the window.
13
Section V
Appendixes
Safety and Legal
Troubleshooting and Routine Maintenance
Menu and Features
Specifications
Glossary
V
66
A
Safety and Legal
Choosing a location
Put your machine on a flat, stable surface that is free of vibration and shocks, such as a desk. Put the machine near a telephone socket and a standard grounded electrical socket. Choose a location where the temperature remains between 10 ° and 35° C (50° F and 95° F).
A
CAUTION
• Avoid placing your machine in a high-traffic area.
• Avoid placing your machine on a carpet.
• DO NOT put the machine near heaters, air conditioners, refrigerators, medical equipment, chemicals or water.
• DO NOT expose the machine to direct sunlight, excessive heat, moisture, or dust.
• DO NOT connect your machine to electrical sockets controlled by wall switches or automatic timers.
• Disruption of power can wipe out information in the machine's memory.
• DO NOT connect your machine to electrical sockets on the same circuit as large appliances or other equipment that might disrupt the power supply.
• Avoid interference sources, such as other cordless telephone systems or speakers.
A
Safety and Legal
To use the machine safely
Please keep these instructions for later reference and read them before attempting any maintenance.
WARNING
A
There are high voltage electrodes inside the machine. Before you clean the inside of the machine, make sure you have unplugged the telephone line cord first and then the power cord from the electrical socket. Doing this will prevent an electrical shock.
DO NOT handle the plug with wet hands. Doing this may cause an electrical shock.
DO NOT pull in the middle of the AC power cord. Doing this might cause an electrical shock.
67
68
DO NOT put your hands on the edge of the machine under the panel cover or touch the document feed rollers. Doing this may cause injury.
DO NOT put your hands on the edge of the paper tray under the output paper tray cover. Doing this may cause injury.
DO NOT touch the paper feed roller. Doing this may cause injury.
Safety and Legal
DO NOT touch the area shaded in the illustration. Doing this may cause injury.
When moving the machine you must lift it from the base, by placing a hand at each side of the unit as shown in the illustration.
If the machine becomes hot, releases smoke or generates any strong smells, immediately unplug the machine from the electrical socket. Call your Brother dealer.
If metal objects, water or other liquids get inside the machine, immediately unplug the machine from the electrical socket. Call your Brother dealer.
69
WARNING
• Use caution when installing or modifying telephone lines. Never touch telephone wires or terminals that are not insulated unless the telephone line has been unplugged at the wall socket. Never install telephone wiring during a lightning storm. Never install a telephone wall socket in a wet location.
• This product must be installed near an electrical socket that is easily accessible. In case of an emergency, you must unplug the power cord from the electrical socket to shut off the power completely.
• Always make sure the plug is fully inserted.
WARNING
IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to people, including the following:
1 DO NOT use this product near water, for example, near a bath tub, wash bowl, kitchen sink or washing machine, in a wet basement or near a swimming pool.
2 Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
3 DO NOT use this product to report a gas leak in the vicinity of the leak.
Important safety instructions
1 Read all of these instructions.
2 Save them for later reference.
3 Follow all warnings and instructions marked on the product.
4 Unplug this product from the wall socket before cleaning the inside of the machine. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.
5 Do not use this product near water.
6 Do not place this product on an unstable cart, stand, or table. The product may fall, causing serious damage to the product.
7 Slots and openings in the cabinet and the back or bottom are provided for ventilation. To ensure reliable operation of the product and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heater. This product should never be placed in a built-in installation unless adequate ventilation is provided.
8 This product should be operated from the type of power source indicated on the label. If you are not sure of the type of power available, call your dealer or local power company.
A
70
Safety and Legal
9 Use only the power cord supplied with this machine.
10 This product is equipped with a 3-wire grounded plug, a plug having a third (grounded) pin.
This plug will only fit into a grounded power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, call your electrician to replace your obsolete outlet. Do not defeat the purpose of the grounded plug.
11 Do not allow anything to rest on the power cord. Do not place this product where people can walk on the cord.
12 Do not place anything in front of the machine that will block received faxes. Do not place anything in the path of received faxes.
13 Wait until pages have exited the machine before picking them up.
14 Unplug this product from the power socket and refer all servicing to Brother Authorized Service
Personnel under the following conditions:
When the power cord is damaged or frayed.
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate normally when the operating instructions are followed, adjust only those controls that are covered by the operating instructions. Incorrect adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation.
If the product has been dropped or the casing has been damaged.
If the product exhibits a distinct change in performance, indicating a need for service.
15 To protect your product against power surges, we recommend the use of a power protection device (Surge Protector).
16 To reduce the risk of fire, electric shock and injury to people, note the following:
Do not use this product near appliances that use water, a swimming pool, or in a wet basement.
Do not use the machine during an electrical storm (there is the remote possibility of an electrical shock) or to report a gas leak in the vicinity of the leak.
IMPORTANT - For your safety
To ensure safe operation, the supplied three-pin plug must be inserted only into a standard threepin electrical socket that is effectively grounded through the normal household wiring.
The fact that the equipment operates satisfactorily does not imply that the power is grounded and that the installation is completely safe. For your safety, if in any doubt about the effective grounding of the power, consult a qualified electrician.
A
Important - Wiring information (for UK only)
If you need to replace the plug fuse, fit a fuse that is approved by ASTA to BS1362 with the same rating as the original fuse.
A
Always replace the fuse cover. Never use a plug that does not have a cover.
71
Warning - This machine must be earthed
The wires in the mains lead are coloured in line with the following code:
Green and Yellow: Earth
Blue: Neutral
Brown: Live
If in any doubt, call a qualified electrician.
EU Directive 2002/96/EC and EN50419
European
Union Only
This equipment is marked with the above recycling symbol. It means that at the end of the life of the equipment, you must dispose of it separately at an appropriate collection point, and not place it in the normal domestic unsorted waste stream. This will benefit the environment for all.
(European Union only)
Legal limitations for copying
It is an offence to make reproductions of certain items or documents with the intent to commit fraud
This memorandum is intended to be guide rather than a complete list.
We suggest you check with relevant legal authorities if in doubt about a particular item or document.
The following are examples of documents which should not be copied:
Money
Bonds or other certificates of indebtedness
Certificates of Deposit
Armed Forces Service or Draft papers.
Passports
Postage Stamps (cancelled or uncancelled)
Immigration Papers
Welfare documents
A
72
A
A
Safety and Legal
Cheques or Drafts drawn by Governmental Agencies
Identification Documents, badges or insignias
Licences and Certificates of Title to motor vehicles
Copyrighted works cannot be copied. Sections of a copyrighted work can be copied for ‘fair dealing.’ Multiple copies would indicate improper use.
Works of art should be considered the equivalent of copyrighted works.
Licenses and Certificates of Title to motor vehicles may not be copied under certain state/provincial laws.
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
Multi-Function Link is a registered trademark of Brother International Corporation.
© 2006 Brother Industries, Ltd. All rights reserved.
Windows and Microsoft are registered trademarks of Microsoft in the U.S. and other countries.
Macintosh and TrueType are registered trademarks of Apple Computer, Inc.
PaperPort is a registered trademark of ScanSoft, Inc.
Presto! PageManager is a registered trademark of NewSoft Technology Corporation.
Each company whose software title is mentioned in this manual has a Software License
Agreement specific to its proprietary programs.
All other brand and product names mentioned in this User's Guide and the Software User's
Guide are registered trademarks of their respective companies.
A
73
B
Troubleshooting and Routine
Maintenance
B
Troubleshooting
If you think there is a problem with your machine, check the chart below and follow the troubleshooting tips.
Most problems can be easily resolved by yourself. If you need additional help, the Brother
Solutions Center offers the latest FAQs and troubleshooting tips. Visit us at http://solutions.brother.com.
If you are having difficulty with your machine
Printing
Difficulty
No printout
Poor printing quality
Suggestions
Check the interface cable on both the machine and your computer. (See the Quick
Setup Guide.)
Make sure the machine is plugged in and not in Power Save mode.
One or more ink cartridges are empty. (See Replacing the ink
Check to see if the LCD is showing an error message. (See Error
Check that the correct printer driver has been installed and chosen.
Make sure the machine is online. Click Start and then Printers and Faxes. Rightclick and choose ‘Brother MFC-XXXX’ (where XXXX is your model name), and make sure that ‘Use Printer Offline’ is unchecked.
Check the print quality. (See Checking the print quality on page 90.)
Make sure the Printer Driver or Paper Type setting in the menu matches the type of paper you are using. (See Printing for Windows
®
or Printing and Faxing for
Macintosh
®
in the Software User's Guide on the CD-ROM and Paper
Make sure that your ink cartridges are fresh. The following may cause ink to clog:
The expiration date written on the cartridge package has passed. (Cartridges stay usable for up to two years if kept in their original packaging.)
The ink cartridge was in your machine over six months.
White horizontal lines appear in text or graphics.
The ink cartridge may not have been stored properly before use.
Try using the recommended types of paper. (See Acceptable paper and other
The recommended environment for your machine is between 20 ° C to 33° C
(68 ° F to 91° F).
Clean the print head. (See Cleaning the print head on page 90.)
Try using the recommended types of paper. (See Acceptable paper and other
The machine prints blank pages.
Clean the print head. (See Cleaning the print head on page 90.)
Characters and lines are stacked.
Check the printing alignment. (See Checking the printing alignment on page 91.)
B
B
74
Troubleshooting and Routine Maintenance
Printing (Continued)
Difficulty Suggestions
Printed text or images are skewed.
Make sure the paper is loaded properly in the paper tray and the paper side guide
is adjusted correctly. (See Loading paper and other media on page 11.)
Make sure the Lower Jam Clear Cover is set properly.
Smudged stain at the top centre of the printed page.
Printing appears dirty or ink seems to run.
Stains appear on the reverse side or at the bottom of the page.
Make sure the paper is not too thick or curled. (See Acceptable paper and other
Make sure you are using the proper types of paper. (See Acceptable paper and
other media on page 7.) Don't handle the paper until the ink is dry.
Make sure the printer platen is not dirty with ink. (See Cleaning the machine printer
Make sure you are using the paper support flap. (See Loading paper and other
Check Reverse Order in the Basic tab of the printer driver.
The machine prints dense lines on the page.
The printouts are wrinkled.
Cannot perform ‘2 in 1 or 4 in 1’ printing.
Print speed is too slow.
In the printer driver Basic tab, click the Settings, and uncheck the
Bi-Directional Printing.
Check that the paper size setting in the application and in the printer driver are the same.
Try changing the printer driver setting. The highest resolution needs longer data processing, sending and printing time. Try the other quality settings in the printer driver Basic tab. Also, click the Settings tab, and make sure you uncheck
Colour Enhancement.
Set the borderless feature off. Borderless printing is slower than normal printing.
(See Printing for Windows
®
or Printing and Faxing for Macintosh
®
in the Software
User's Guide on the CD-ROM.)
Machine feeds multiple pages
Printed pages are not stacked neatly.
Printed pages double-feed and cause a paper jam.
Make sure the paper is loaded properly in the paper tray. (See Loading paper and
Check that more than two types of paper are not loaded in the paper tray at any one time.
Make sure you are using the paper support flap. (See Loading paper and other
Close the output paper tray cover and slide it forward, then push the paper tray firmly back into the machine. While holding the paper tray in place, pull out the paper support until it clicks and unfold the paper support flap. (See the illustrations
in Loading paper and other media on page 12.)
Try setting the Display setting to ‘256 colours.
’ Machine does not print from Paint
Brush.
Machine does not print from Adobe
Illustrator.
Try to reduce the print resolution. (See Printing for Windows
®
or Printing and
Faxing for Macintosh ® in the Software User's Guide on the CD-ROM.)
The machine cannot print full pages of a document.
Reduce the printing resolution. (See Printing for Windows
®
or Printing and Faxing for Macintosh
®
in the Software User's Guide on the CD-ROM.)
Out of Memory
message occurs.
Reduce the complexity of your document and try again. Reduce the graphic quality or the number of font sizes within your application software.
75
Printing Received Faxes
Difficulty
Condensed print and white streaks across the page or the top and bottom of sentences are cut off.
Suggestions
You probably had a bad connection, with static or interference on the telephone line. Ask the other party to send the fax again.
Vertical black lines when receiving. The sender's scanner may be dirty. Ask the sender to make a copy to see if the problem is with the sending machine. Try receiving from another fax machine.
Received colour fax prints only in black and white.
Replace the colour ink cartridges that are empty or nearly empty, and then ask the
other person to send the colour fax again. (See Replacing the ink
Left and Right margins are cut off or a single page is printed on two pages.
Turn on Auto Reduction. (See Printing a reduced incoming fax on page 30.)
Phone Line or Connections
Difficulty
Dialling does not work. (No dial tone)
The machine does not answer when called.
Suggestions
Check that the machine is plugged in and switched on.
Check all line cord connections.
Change Tone/Pulse setting. (See Quick Setup Guide.)
Lift the external phone’s handset, (or the machine’s handset if available), and then dial the number to send a manual fax. Wait to hear fax receiving tone before pressing Mono Start or Colour Start.
Make sure the machine is in the correct receiving mode for your setup. (See
Receive modes on page 27.) Check for a dial tone. If possible, call your machine
to hear it answer. If there is still no answer, check the telephone line cord connection. If there is no ringing when you call your machine, ask your telephone company to check the line.
Receiving Faxes
Difficulty
Cannot receive a fax
Suggestions
Check all line cord connections.
Make sure the machine is in the correct receiving mode for your setup. (See
If you connect your machine to PBX or ISDN, set the menu setting of Phone Line
Type to your phone type. (See Setting the Phone Line Type on page 34.)
76
Troubleshooting and Routine Maintenance
Sending Faxes
Difficulty
Cannot send a fax
Suggestions
Check all line cord connections.
Make sure that the Fax
key is illuminated. (See Entering Fax
Ask the other party to check that the receiving machine has paper.
Print the Transmission Verification Report and check for an error. (See
Make sure the panel cover is completely closed.
Transmission Verification Report says ‘Result:NG’ or
‘Result:ERROR’.
There is probably temporary noise or static on the line. Try sending the fax again.
If you send a PC FAX message and get ‘Result:NG’ on the Transmission
Verification Report, your machine may be out of memory. If the problem continues, ask the telephone company to check your phone line.
If you often get transmission errors due to possible interference on the phone line,
try changing the menu setting of Compatibility to Basic. (See Phone line
If you connect your machine to PBX or ISDN, set the menu setting of Phone Line
Type to your phone type. (See Setting the Phone Line Type on page 34.)
Poor fax send quality.
Try changing your resolution to Fine or S.Fine. Make a copy to check your machine's scanner operation. If the copy quality is not good, clean the scanner.
(See Cleaning the scanner on page 88.)
Vertical black lines when sending.
If the copy you made shows the same problem, clean the scanner. (See Cleaning
Handling Incoming Calls
Difficulty
The machine ‘Hears’ a voice as a
CNG Tone.
Suggestions
If Fax Detect is set to on, your machine is more sensitive to sounds. It may mistakenly interpret certain voices or music on the line as a fax machine calling and respond with fax receiving tones. Deactivate the machine by pressing
Stop/Exit. Try avoiding this problem by turning Fax Detect to off. (See Fax
Sending a fax call to the machine.
If you answered at the machine, press Mono Start and hang up at once. If you answered on an external or extension phone, press your Fax Receive Code
(default setting is l 51). When your machine answers, hang up.
Custom features on a single line.
If you have Call Waiting, Call Waiting/Caller ID, an alarm system or other custom feature on a single phone line with your machine, it may create a problem sending or receiving faxes.
For example: If you subscribe to Call Waiting or some other custom service and its signal comes through the line while your machine is sending or receiving a fax, the signal can temporarily interrupt or disrupt the faxes. Brother's ECM feature should help overcome this problem. This condition is related to the telephone system industry and is common to all devices that send and receive information on a single, shared line with custom features. If avoiding a slight interruption is crucial to your business, a separate phone line with no custom features is recommended.
77
Menu Setting Difficulty
Difficulty
The machine beeps when you try to access the Setup Receive menu.
Suggestions
If the Fax key is not illuminated, press it to turn on Fax mode. The Setup
Receive setting is available only when the machine is in Fax mode.
Copying Difficulty
Difficulty
Cannot make a copy
Suggestions
Make sure that the Copy
key is illuminated. (See Entering Copy
Make sure the panel cover is completely closed.
Vertical streaks appear on copies
If you see vertical streaks on copies, clean the scanner. (See Cleaning the
Scanning Difficulty
Difficulty
Cannot scan
TWAIN/WIA errors appear while scanning.
Suggestions
Make sure the panel cover is completely closed.
Make sure the Brother TWAIN/WIA driver is chosen as the primary source. In
PaperPort® SE with OCR, click File, Scan and choose the Brother TWAIN/WIA driver.
Software Difficulty
Difficulty
Cannot install software or print
‘Device Busy’
Suggestions
Run the Repair MFL-Pro Suite program on the CD-ROM. This program will repair and reinstall the software.
Make sure the machine is not showing an error message on the LCD.
78
Troubleshooting and Routine Maintenance
Error messages
As with any sophisticated office product, errors may occur. If this happens, your machine identifies the error and shows an error message. The most common error messages are shown below.
You can correct most errors by yourself. If you need more help, the Brother Solutions Center offers latest FAQs and troubleshooting tips.
Visit us at http://solutions.brother.com.
B
Error Message
BT Call Sign
On
(For UK only)
Change Unable XX
Clean Unable XX
Comm.Error
Cause
BT Call Sign is set to ON. You cannot change the Receive Mode from Manual to another mode.
The machine has a mechanical problem.
—OR—
A foreign objects such as a clip or ripped paper is in the machine.
Poor phone line quality caused a communication error.
Cover Open
Close all covers
The Upper Jam Clear Cover is not closed completely.
The ink cartridge cover is not closed completely.
Data Remaining
Print data is left in the machine's memory.
Print data is left in the machine's memory. The USB cable was unplugged while the computer was sending the data to the machine.
Disconnected
The other person or other person's fax machine stopped the call.
Document Jam
The document was not inserted or fed properly, or the document scanned from the ADF was too long.
The panel cover is open.
High Temperature
The print head is too warm.
Action
Set BT Call Sign to OFF. (See BT Call Sign (For
Open the Upper Clear Jam Cover and remove any foreign objects inside the machine. If the
error message continues, see Transferring your
faxes or Fax Journal report on page 81 before
disconnecting the machine so you will not lose any important messages. Then, disconnect the machine from the power for several minutes and then reconnect it.
Try sending the fax again or try connecting the machine to another telephone line. If the problem continues, call the telephone company and ask them to check your phone line.
Open the Upper Jam Clear Cover and then close it again.
Firmly close the ink cartridge cover until it clicks.
Re-start printing from your computer.
Press Stop/Exit. The machine will cancel the job and clear it from the memory. Try to print again.
Try to send or receive again.
Close the panel cover and press Stop/Exit.
Allow the machine to cool down.
79
Error Message Cause
Init Unable XX
The machine has a mechanical problem.
—OR—
A foreign objects such as a clip or ripped paper is in the machine.
Ink Empty XX
One or more of the ink cartridges is empty. The machine will stop all print operations. While memory is available, black and white faxes will be stored in the memory. If a sending machine has a colour fax, the machine's ‘handshake’ will ask that the fax be sent as black and white. If the sending machine has the ability to convert it, the colour fax will be stored in the memory as a black and white fax.
Low Temperature
The print head is too cold.
Near Empty XX
One or more of the ink cartridges are running out of ink. If a sending machine has a colour fax, the machine's ‘handshake’ will ask that the fax be sent as black and white.
If the sending machine has the ability to convert it, the colour fax will be received into memory as a black and white fax.
No Caller ID
(U.K. and Ireland only)
There is no incoming call history.
You did not receive calls or you have not subscribed to the Caller ID service from your telephone company.
No Cartridge
An ink cartridge is not installed properly.
Action
Open the Upper Jam Clear Cover and remove any foreign objects inside the machine. If the
error message continues, see Transferring your
faxes or Fax Journal report on page 81 before
disconnecting the machine so you will not lose any important messages. Then, disconnect the machine from the power for several minutes and then reconnect it.
Replace the ink cartridges. (See Replacing the
Allow the machine to warm up.
Order a new ink cartridge.
If you want to use the Caller ID feature call your
telephone company. (See Caller ID (For U.K. and
No Paper Fed
The machine is out of paper or paper is not properly loaded in the paper tray.
Take out the ink cartridge and put it in again
seating it properly. (See Replacing the ink
Do one of the following:
Refill the paper in the paper tray, and then press Mono Start or Colour Start.
Remove the paper and load it again and then press Mono Start or Colour Start.
See Printer jam or paper jam on page 83.
The paper is jammed in the machine.
No Response/Busy
The number you dialed does not answer or is busy.
Verify the number and try again.
80
Troubleshooting and Routine Maintenance
Error Message
Out of Memory
Paper Jam
Cause
Not Registered
You tried to access a Speed Dial number that is not programmed.
The machine's memory is full.
Print Unable XX
Scan Unable XX
The machine has a mechanical problem.
—OR—
A foreign objects such as a clip or ripped paper is in the machine.
Wrong Paper Size
Paper is jammed in the machine.
Paper is not the correct size.
Action
Set up the Speed Dial number. (See Storing
Speed-Dial numbers on page 41.)
Fax sending or copy operation in progress
Press Stop/Exit and wait until the other operations in progress finish and then try again.
Clear the data from the memory. To gain extra memory, you can turn off Fax Storage.
Print the faxes that are in the memory. (See
Printing a fax from the memory on page 31.)
Printing operation in progress
Reduce print resolution. (For details, see
Printing for Windows
®
or Printing and Faxing for
Macintosh
®
in the Software User's Guide on the
CD-ROM.)
Open the upper and lower jam clear covers (at the back of the machine) and remove the
jammed paper. (See Printer jam or paper
Open the upper jam clear cover and remove any foreign objects inside the machine.
If the error message continues, see Transferring
your faxes or Fax Journal report on page 81
before disconnecting the machine so you will not lose any important messages. Then, disconnect the machine from the power for several minutes and then reconnect it.
Load the correct size of paper (Letter, Legal or
A4), and then press Mono Start or Colour Start.
Transferring your faxes or Fax
Journal report
B
If the LCD shows:
Change Unable XX
Clean Unable XX
Init Unable XX
Print Unable XX
Scan Unable XX we recommend transferring your faxes to
another fax machine. (See Transferring faxes
to another fax machine on page 82.)
You can also transfer the Fax Journal report to see if there are any faxes you need to
transfer. (See Transferring Fax Journal report
to another fax machine on page 82.)
Note
If there is an error message on the machine's LCD, after the faxes have been transferred, disconnect the machine from the power source for several minutes, and then reconnect it.
81
Transferring faxes to another fax machine
If you have not set up your Station ID, you cannot enter fax transfer mode.
B a
Press Stop/Exit to interrupt the error temporarily.
b
Press Menu, 9, 0, 1.
c
Do one of the following:
If the LCD shows No Data, there are no faxes left in the machine's memory.
Press Stop/Exit.
If the LCD shows Enter Fax No., enter the fax number to which faxes will be forwarded. d
Press Mono Start.
Transferring Fax Journal report to another fax machine
If you have not set up your Station ID, you cannot enter fax transfer mode.
B a
Press Menu 9, 0, 2.
b
Enter the fax number to which the Fax
Journal report will be forwarded.
c
Press Mono Start.
Document jam
Documents can jam if they are not inserted or fed properly, or if they are too long. Follow the steps below to clear a document jam.
B
Document is jammed inside the front of the machine
B a
Take out any paper from the ADF that is not jammed.
b
Pull the jammed document (1) out toward the front of the machine.
1 c
Press Stop/Exit.
Document is jammed inside the panel cover
B a
Take out any paper from the ADF that is not jammed.
b
Open the panel cover.
c
Pull the jammed document out.
d
Close the panel cover.
e
Press Stop/Exit.
82
Printer jam or paper jam
Take out the jammed paper depending on where it is jammed in the machine. Open and close the Upper Jam Clear Cover to clear the error.
a
Pull the paper tray (1) out of the machine.
B
Troubleshooting and Routine Maintenance c
Remove the Lower Jam Clear Cover (1) from the back of the machine. Pull the jammed paper out of the machine.
1
1 b
Pull out the jammed paper (1).
1 d
Put the Lower Jam Clear Cover back on.
Make sure the cover is set properly.
If you cannot remove the jammed paper from the front side, or the error message still appears on the LCD after you remove the jammed paper, please go to the next step.
83
e
Open the Upper Jam Clear Cover (1).
Make sure that there is no jammed paper left in the corners of the machine.
1
Dial Tone detection
When you send a fax automatically, by default your machine will wait for a fixed amount of time before it starts to dial the number. By changing the Dial Tone setting to
Detection
you can make your machine dial as soon as it detects a dial tone. This setting can save a small amount of time when sending a fax to many different numbers. If you change the setting and start having problems with dialling you should change back to the default No Detection setting.
a
Press Menu, 0, 5.
b
Press a or b to choose Detection or
No Detection
.
Press OK.
c
Press Stop/Exit.
B
Note
If the paper is jammed under the print head, unplug the machine from the power source, and then move the print head to take out the paper.
f
Close the Upper Jam Clear Cover.
g
Push the paper tray firmly back into the machine. While holding the paper tray in place, pull out the paper support until it clicks and unfold the paper support flap.
(See the illustrations in Loading paper
84
Phone line interference
If you are having problems sending or receiving a fax due to possible interference on the phone line, we recommend that you adjust the Equalization for compatibility to reduce the modem speed for fax operations.
a
Press Menu, 2, 0, 2.
b
Press a or b to choose Normal,
Basic
(or High).
Basic
cuts the modem speed to
9,600 bps. Unless interference is a recurring problem on your phone line, you may prefer to use it only when needed.
Normal
sets the modem speed at
14,400 bps.
High
ssets the modern speed at
33,600 bps. (Default)
Press OK.
c
Press Stop/Exit.
Note
When you change the compatibility to
Basic
, the ECM feature is only available for colour fax sending.
B
Troubleshooting and Routine Maintenance
Routine maintenance
B
Replacing the ink cartridges
B
Your machine is equipped with an ink dot counter. The ink dot counter automatically monitors the level of ink in each of the 4 cartridges. When the machine detects an ink cartridge is running out of ink, the machine will tell you with a message on the LCD.
The LCD will tell you which ink cartridge is low or needs replacing. Be sure to follow the LCD prompts to replace the ink cartridges in the correct order.
Even though the machine tells you that an ink cartridge is empty, there will be a small amount of ink left in the ink cartridge. It is necessary to keep some ink in the ink cartridge to prevent air from drying out and damaging the print head assembly.
a
Open the ink cartridge cover.
If one or more ink cartridges are empty, for example Black, the LCD shows
Ink Empty Black
and
Replace Ink
.
b
Pull the lock release lever and take out the ink cartridge for the colour shown on the LCD.
85
e
Each colour has its own correct position.
Insert the ink cartridge in the direction of the arrow on the label.
c
Open the new ink cartridge bag for the colour shown on the LCD, and then take out the ink cartridge.
d
Remove the protective yellow cap (1).
1
M brother
XXXX f
Lift the lock release lever and gently push it until it clicks, and then close the ink cartridge cover.
Improper Setup
DO NOT touch the area shown in the illustration below.
86
Note
If the protective yellow cap comes off when you open the bag, the cartridge will not be damaged.
g
If you replaced an ink cartridge, the LCD may ask you to verify that it was a brand new one. (For example,
Did You Change Blck?
) For each new cartridge you installed, press 1
(Yes) to automatically reset the ink dot counter for that colour. If the ink cartridge you installed is not a brand new one, be sure to press 2 (No).
If you wait until the LCD shows
Near Empty XX
or Ink Empty XX, the machine will automatically reset the ink dot counter.
Note
If the LCD shows No Cartridge after you install the ink cartridges, check that the ink cartridges are installed properly.
Troubleshooting and Routine Maintenance
WARNING
If ink gets in your eyes, wash them out with water at once and call a doctor if you are concerned.
CAUTION
DO NOT take out ink cartridges if you do not need to replace them. If you do so, it may reduce the ink quantity and the machine will not know the quantity of ink left in the cartridge.
DO NOT touch the cartridge insertion slots.
If you do so, the ink may stain your skin.
If ink stains your skin or clothing, wash with soap or detergent at once.
If you mix the colours by installing an ink cartridge in the wrong position, clean the print head several times after correcting the cartridge installation.
Once you open an ink cartridge, install it in the machine and use it up within six months of installation. Use unopened ink cartridges by the expiration date written on the cartridge package.
DO NOT dismantle or tamper with the ink cartridge; this can cause the ink to leak out of the cartridge.
Brother multifunction machines are designed to work with ink of a particular specification and will work to a level of optimum performance when used with genuine Brother Branded ink cartridges.
Brother cannot guarantee this optimum performance if ink or ink cartridges of other specifications are used. Brother does not therefore recommend the use of cartridges other than genuine Brother Branded cartridges or the refilling of empty cartridges with this machine or the refilling of empty cartridges with ink from other sources. If damage is caused to the print head or other parts of this machine as a result of using incompatible products with this machine, any repairs required as a result may not be covered by the warranty.
Cleaning the outside of the machine
B
CAUTION
Use neutral detergents. Cleaning with volatile liquids such as thinner or benzine will damage the outside surface of the machine.
DO NOT use cleaning materials that contain ammonia.
DO NOT use isopropyl alcohol to remove dirt from the control panel. It may crack the panel.
87
Clean the outside of the machine as follows: a
Pull the paper tray (1) completely out of the machine.
B d
Lift the output paper tray cover and wipe the inside and outside of the paper tray with a soft cloth to remove dust.
1 b
Wipe the outside of the machine with a soft cloth to remove dust.
e
Close the output paper tray cover and put the paper tray firmly back in the machine.
Cleaning the scanner
a
Unplug the machine, open the panel cover (1). Clean the white bar (2) and the glass strip (3) with isopropyl alcohol on a soft lint-free cloth.
1
B c
Remove anything that is stuck inside the paper tray.
2
3
88
Cleaning the machine printer platen
B
WARNING
Unplug the machine from the AC power outlet before cleaning the printer platen (1).
a
Clean the machine printer platen (1) and the area around it, wiping off any scattered ink with a soft, dry, lint-free cloth.
Troubleshooting and Routine Maintenance
Cleaning the paper pick-up roller
B a
Pull the paper tray completely out of the machine.
b
Unplug the machine from the electrical socket and remove the Lower Jam Clear
Cover (1).
1
1 c
Clean the Paper Pick-up Roller (1) with isopropyl alcohol on a cotton swab.
1 d
Put the Lower Jam Clear Cover back on.
Make sure the cover is set properly.
e
Put the paper tray firmly back in the machine.
f
Re-connect the power cord.
89
Cleaning the print head
To ensure good print quality, the machine will regularly clean the print head. You can start the cleaning process manually if needed.
Clean the print head and ink cartridges if you get a horizontal line in the text or graphics on your printed pages. You can clean Black only, three colours at a time
(Yellow/Cyan/Magenta), or all four colours at once.
Cleaning the print head consumes ink.
Cleaning too often uses ink unnecessarily.
B
CAUTION
DO NOT touch the print head. Touching the print head may cause permanent damage and may void the print head's warranty.
a
Press Ink Management.
b
Press a or b to choose Cleaning.
Press OK.
c
Press a or b to choose Black, Color or All.
Press OK.
The machine cleans the print head.
When cleaning is finished, the machine will go back to standby mode automatically.
Note
If you clean the print head at least five times and the print has not improved, call your Brother dealer for service.
Checking the print quality
If faded or streaked colours and text appear on your output, some of the nozzles may be clogged. You can check this by printing the
Print Quality Check Sheet and looking at the nozzle check pattern.
a
Press Ink Management.
b
Press a or b to choose Test Print.
Press OK.
c
Press a or b to choose
Print Quality
.
Press OK.
d
Press Colour Start.
The machine begins printing the Print
Quality Check Sheet.
e
Check the quality of the four colour blocks on the sheet.
Is Quality OK?
1.Yes 2.No
f
Do one of the following:
If all lines are clear and visible, press
1 to choose Yes.
Press Stop/Exit.
If you can see missing short lines as shown below, press 2 to choose No.
B
OK Poor g
The LCD asks you if the print quality is
OK for black and three colours.
Black OK?
1.Yes 2.No
Press 1 (Yes) or 2 (No).
90
h
The LCD asks you if you want to start cleaning.
Start Cleaning?
1.Yes 2.No
Press 1 (Yes).
The machine starts cleaning the print head.
i
After cleaning is finished, press
Colour Start.
The machine starts printing the Print
Quality Check Sheet again and then
j
Press Stop/Exit.
If you repeat this procedure at least five times and the print quality is still poor, replace the ink cartridge for the clogged colour.
After replacing the ink cartridge, check the print quality. If the problem still exists, repeat the cleaning and test print procedures at least five times for the new ink cartridge. If ink is still missing, call your Brother dealer.
CAUTION
DO NOT touch the print head. Touching the print head may cause permanent damage and may void the print head's warranty.
Note
i
When a print head nozzle is clogged the printed sample looks like this.
After the print head nozzle is cleaned, the horizontal lines are gone.
Troubleshooting and Routine Maintenance
Checking the printing alignment
You may need to adjust the printing alignment after transporting the machine if your printed text becomes blurred or images become faded.
a
Press Ink Management.
b
Press a or b to choose Test Print.
Press OK.
c
Press a or b to choose Alignment.
Press OK.
d
Press Mono Start or Colour Start.
The machine starts printing the
Alignment Check Sheet.
Is Alignment OK?
1.Yes 2.No
e
Check the 600 dpi and 1200 dpi test prints to see if number 5 most closely matches number 0.
If the number 5 sample of both the
600 dpi and 1200 dpi are the best matches, press 1 (Yes) to finish
Alignment Check, and go to step h.
If another test print number is a better match for either 600 dpi or
1200 dpi, press 2 (No) to choose it.
f
For 600 dpi, press the number of the test print that most closely matches the number 0 sample (1-8).
600dpi Adjust
Select Best # 5 g
For 1200 dpi, press the number of the test print that most closely matches the number 0 sample (1-8).
1200dpi Adjust
Select Best # 5 h
Press Stop/Exit.
B
91
Checking the ink volume
You can check the ink that is left in the cartridge.
a
Press Ink Management.
b
Press a or b to choose Ink Volume.
Press OK.
The LCD shows the ink volume.
Ink Volume e
BK:nnnonnn+ e c
Press a or b to choose the colour you want to check. d
Press Stop/Exit.
Note
You can check the ink volume from your computer. (See Printing for Windows
®
or
Printing and Faxing for Macintosh
®
in the
Software User's Guide on the CD-ROM.)
B
Machine Information
B
Checking the serial number
You can see the machine’s serial number on the LCD.
a
Press Menu, 5, 1.
1.Serial No.
b
Press OK.
XXXXXXXXX c
Press Stop/Exit.
B
Packing and shipping the machine
B
When you transport the machine, use the packing materials that came with your machine. If you do not pack the machine properly, you could void your warranty.
CAUTION
It is important to allow the machine to ‘park’ the print head after a print job. Listen carefully to the machine before unplugging it to make sure that all mechanical noise has stopped. Not allowing the machine to finish this parking process may lead to print problems and possible damage to the print head.
a
Open the ink cartridge cover.
b
Pull the lock release levers down and take out all the ink cartridges.
c
Install the yellow protective part, lift each lock release lever and push it until it clicks, and then close the ink cartridge cover.
92
Troubleshooting and Routine Maintenance
CAUTION
If you are not able to find the yellow protective part, DO not remove the ink cartridges before shipping. It is essential that the machine be shipped with either the yellow protective part or the ink cartridges in position. Shipping without them will cause damage to your machine and may void your warranty.
d
Unplug the machine from the telephone wall socket and take the telephone line cord out of the machine.
e
Unplug the machine from the electrical socket.
f
Unplug the interface cable from the machine, if it is connected.
g
If your machine has a handset, remove it and the handset curled cord.
h
Wrap the machine in the bag and put it in the original carton with the original packing material.
i
Pack the printed materials and additional parts in the original carton as shown below. Do NOT pack the used ink cartridges in the carton.
j
Close the carton and tape it shut.
93
94
C
Menu and Features
On-screen programming
Your machine is designed to be easy to use with LCD on-screen programming using the menu keys. User-friendly programming helps you take full advantage of all the menu selections your machine has to offer.
Since your programming is done on the LCD, we have created step-by-step on-screen instructions to help you program your machine. All you need to do is follow the instructions as they guide you through the menu selections and programming options.
C
Menu table
You can program your machine by using the
menu table that begins on page 96. These
pages list the menu selections and options.
Press Menu followed by the menu numbers to program your machine.
For example, to set beeper volume to Low.
a
Press Menu, 1, 4, 2.
b
Press a or b to choose Low.
c
Press OK.
C
Memory storage
Even if there is a power failure, you will not lose your menu settings because they are stored permanently. Temporary settings
(such as Contrast, Overseas mode, and so on) will be lost. You may have to reset the date and time.
C
C
Menu keys
Access the menu
Go to the next menu level
Accept an option
Go back to the previous menu level.
Delete an incorrect letter when you need to enter text into the machine.
Scroll through the current menu level.
Go back to the previous menu level.
Exit the menu.
C
Menu and Features
To access the menu mode: a
Press Menu.
b
Choose an option.
Press 1 for General Setup menu.
Press 2 for Fax menu.
Press 3 for Copy menu.
Press 0 for Initial Setup.
You can scroll more quickly through each menu level by pressing a or b for the direction you want.
c
Press OK when that option appears on the LCD.
The LCD will then show the next menu level.
d
Press a or b to scroll to your next menu selection.
e
Press OK.
When you finish setting an option, the
LCD shows Accepted.
95
Menu Table
The menu table will help you understand the menu selections and options that are found in the machine's programs. The factory settings are shown in Bold with an asterisk.
C
Choose & OK Choose & OK to accept to exit
Main Menu
1.General
Setup
Submenu Menu Selections
1.Mode Timer
—
2.Paper Type
3.Paper Size
—
—
Options
0 Sec
30 Sec
*
1 Min
2 Mins
5 Mins
Off
Plain Paper
*
Inkjet Paper
Brother Photo
Other Photo
Transparency
Letter
Legal
A4
*
A5
10x15cm
Descriptions
Sets the time to return to
Fax mode.
Page
Sets the type of paper in the paper tray.
Sets the size of the paper in the paper tray.
96
Menu and Features
Main Menu
1.General
Setup
(Continued)
2.Fax
Submenu
4.Volume
5.Auto Daylight
6.P.Save Setting
7.LCD Contrast
1.Setup Receive
(In Fax mode only)
Menu Selections
1.Ring
2.Beeper
3.Speaker
—
—
—
1.Ring Delay
05
06
07
08
2.F/T Ring Time 20
Sec
30
Sec*
3.Fax Detect
40
Sec
70
Sec
On
*
Semi
Off
Options
Off
Low
Med
*
High
Off
Low
*
Med
Descriptions
Adjusts the ring volume.
Adjusts the volume level of the beeper.
Page
01
02
*
03
04
High
Off
Low
Med
*
High
On
*
Off
Light
Dark
*
(Example for the
UK)
00
Adjusts the speaker volume.
Fax Receive:On
*
Fax Receive:Off
Changes for Daylight
Savings Time automatically.
Customizes the
Power Save key not to receive faxes in power save mode.
Adjusts the contrast of the
LCD.
Sets the number of rings before the machine answers in Fax Only or
Fax/Tel mode.
Sets the pseudo/doublering time in Fax/Tel mode.
Receives fax messages without pressing Start.
97
Main Menu
2.Fax
(Continued)
Submenu
1.Setup Receive
(Continued)
(In Fax mode only)
Menu Selections
4.Remote Codes On
* (l51, #51)
5.Auto Reduction
Options
Off
On
*
Off
6.Memory Receive On
*
Off
7.Polling RX
3.Delayed Fax
Standard
2.Setup Send
(In Fax mode only)
1.Contrast
Secure
Timer
Auto
*
Light
Dark
2.Fax Resolution Standard
*
Fine
S.Fine
Photo
—
Descriptions
Allows you to answer all calls at an extension or external phone and use codes to turn the machine on or off. You can personalize these codes.
Cuts the size of incoming faxes.
Page
Automatically stores any incoming faxes in its memory if it runs out of paper.
Sets up your machine to poll another fax machine.
Changes the lightness or darkness of faxes you send.
Sets the default resolution for outgoing faxes.
4.Batch TX
5.Real Time TX Next Fax Only
Off
*
6.Polled TX
On
Standard
Secure
7.Overseas Mode
On
Off
On
Off
*
*
Set the time of day in
24-hour format that the delayed faxes will be sent.
Combines delayed faxes to the same fax number at the same time of day into one transmission.
Sends a fax without using the memory.
Sets up the document on your machine to be retrieved by another fax machine.
If you are having problems sending faxes overseas, set this to on.
98
Menu and Features
Main Menu
2.Fax
(Continued)
Submenu
3.Set
Quick-Dial
Menu Selections
2.Speed-Dial
3.Setup Groups
Options
1.One-Touch Dial
—
—
—
4.Report Setting 1.XMIT Report On
On+Image
Off
*
Off+Image
2.Journal Period Off
Every 50 Faxes
*
Every 6 Hours
Every 12 Hours
Every 24 Hours
5.Remote Fax
Opt
Every 2 Days
Every 7 Days
1.Forward/Store Off
*
Fax Forward
Fax Storage
6.Remaining
Jobs
0.Miscellaneous
2.Remote Access
3.Print Document
—
1.TX Lock
---l
—
—
—
Sets the machine to forward fax messages or to store incoming faxes in the memory so you can retrieve them while you are away from your machine.
You must set your own code for Remote Retrieval.
Prints incoming faxes stored in the memory.
Checks which jobs are in the memory and lets you cancel chosen jobs.
Prohibits most operations other than receiving faxes.
Adjusts the equalization for transmission problems.
2.Compatibility
High
*
Normal
Basic
Off
*
3.BT Call Sign
(U.K. only)
4.Caller ID
(U.K. and Ireland only)
On
Display ID
*
Print Report
Descriptions
Stores One-Touch Dial numbers, so you can dial by pressing only a few keys (and Start).
Stores Speed-Dial numbers, so you can dial by pressing only a few keys (and Start).
Sets up a Group number for Broadcasting.
Sets initial setup for
Transmission Verification
Report and Fax Journal.
Page
Uses with BT Call Sign.
View or print a list of the last 30 Caller IDs stored in the memory.
99
Main Menu
3.Copy
4.Print Reports
Submenu
1.Quality
2.Brightness
3.Contrast
4.Color Adjust
1.XMIT Verify
Menu Selections
—
—
—
1.Red
2.Green
3.Blue
—
Options
Best
Fast
Normal
*
nnnno +
nnnon +
nnonn +*
nonnn +
onnnn +
nnnno +
nnnon +
nnonn +*
nonnn +
onnnn +
R:-
nnnno +
R:-
nnnon +
R:-
nnonn +*
R:-
nonnn +
R:-
onnnn +
G:-
nnnno +
G:-
nnnon +
G:-
nnonn +*
G:-
nonnn +
G:-
onnnn +
B:-
nnnno +
B:-
nnnon +
B:-
nnonn +*
B:-
nonnn +
B:-
onnnn +
—
2.Help List
3.Quick-Dial
—
—
—
—
Descriptions
Chooses the Copy resolution for your type of document.
Page
Adjusts the brightness for copies.
Adjusts the contrast for copies.
Adjusts the amount of Red in copies.
Adjusts the amount of
Green in copies.
Adjusts the amount of Blue in copies.
Prints a Transmission
Verification Report for your last transmission.
Prints the Help List so you can see at-a-glance how to quickly program your machine.
Lists name and numbers stored in the One-Touch and Speed-Dial memory, in numerical order.
100
Menu and Features
Main Menu
4.Print Reports
(Continued)
Submenu Menu Selections
4.Fax Journal
—
5.Machine
Info.
0.Initial Setup
5.User Settings
1.Serial No.
1.Receive Mode
2.Date/Time
3.Station ID
4.Tone/Pulse
5.Dial Tone
6.Phone Line
Set
—
—
—
—
—
—
—
—
Options
—
—
—
Fax Only
*
Fax/Tel
External TAD
Manual
—
Descriptions
Lists information about the last incoming and outgoing faxes. (TX means
Transmit.) (RX means
Receive.)
Lists your settings.
Lets you check the serial number of your machine.
Choose the receive mode that best suits your needs.
Page
Fax:
Name:
Tone
*
Pulse
Detection
No Detection
*
Normal
*
PBX
ISDN
Puts the date and time on the LCD and in headings of faxes you send.
Set your name and fax number to appear on each page you fax.
Choose the dialling mode.
See
Quick
Setup
Guide
Turns Dial Tone Detection on or off.
Select the phone line type. 34
101
Entering Text
When you are setting certain menu selections, such as the Station ID, you may need to enter text into the machine. Most dial pads have three or four letters printed on keys. The keys for 0, # and l do not have printed letters because they are used for special characters.
By pressing the correct dial pads repeatedly, you can access the character you want.
C
Press
Key
2
5
6
3
4
7
8
9 one time
A
J
M
D
G
P
T
W two times
B
K
N
E
H
Q
U
X three times
C
L
O
F
I
R
V
Y four times
2
5
6
3
4
S
8
Z
Putting spaces
To enter a space in a fax number, press c once between numbers. To enter a space in a name, press c twice between characters.
C
Making corrections
If you entered an incorrect letter and want to change it, press d to move the cursor under the incorrect character. Then press
Clear/Back. Re-enter the correct character.
You can also back up and insert letters.
C
Repeating letters
If you need to enter a letter that is on the same key as the letter before, press c to move the cursor to the right before you press the key again.
C
Special characters and symbols
Press l, # or 0, and then press d or c to move the cursor under the special character or symbol you want. Then press OK to choose it.
C
Press l for
Press # for
Press 0 for
(space) ! " # $ % & ' ( ) l
+ , - . / m
: ; < = > ? @ [ ] ^ _
Ä Ë Ö Ü À Ç È É 0
102
D
Specifications
General
Memory Capacity
ADF (automatic document feeder)
Paper Tray
Printer Type
Print Method
LCD (Liquid Crystal
Display)
Power Source
Power Consumption
16 MB
Up to 20 pages
Temperature: 20 ° C - 30° C (68° F - 86° F)
Humidity: 50% - 70%
Paper: [80 g/m
2
(20 lb)] A4 size
100 Sheets [80 g/m
2
(20 lb)]
Ink Jet
Mono:
Colour:
16 characters × 1 line
Piezo with 94 × 1 nozzles
Piezo with 94 × 3 nozzles
AC 220 to 240V 50/60Hz
Power Save Mode:
Standby:
Operating:
Average 4 W
Average 6 W
Average 26 W
D
D
103
Dimensions
325 mm
(12.8 in.)
214 mm
(8.4 in.)
Weight
407 mm (16.0 in.)
6.0 kg (13.2 lb)
292 mm (11.5 in.)
490 mm (19.3 in.)
Noise Operating:
Temperature Operating:
Humidity
Best Print Quality:
Operating:
Best Print Quality:
1 This depends on printing conditions.
10 to 35 ° C (50° F to 95° F)
20 to 33 ° C (68° F to 91° F)
20 to 80% (without condensation)
20 to 80% (without condensation)
104
Specifications
Print media
Paper Input
Paper Output
Paper Tray
Paper type:
Plain paper, inkjet paper (coated paper), glossy paper
, transparencies
Paper size:
Letter, Legal, Executive, A4, A5, A6, JIS B5, envelopes
(commercial No.10, DL, C5, Monarch, JE4), Photo Card,
Index card and Post card
.
For more details, see Paper weight, thickness and
Maximum paper tray capacity: Up to 100 sheets of
80 g/m
2
(20 lb) plain paper
Up to 50 sheets of 80 g/m
2
(20 lb) plain paper (face up print
delivery to the output paper tray)
1
2
3
Use only transparencies recommended for inkjet printing.
For glossy paper or transparencies, we recommend removing printed pages from the output paper tray immediately after they exit the machine to avoid smudging.
See Paper type and size for each operation on page 9.
D
105
Fax
Compatibility
Coding System
Modem Speed
Document Size
Scanning Width
Printing Width
Grey Scale
Polling Types
Contrast Control
Resolution
Speed-Dial
One-Touch
Broadcasting
Automatic Redial
Auto Answer
Communication Source
Memory Transmission
Out of Paper Reception
ITU-T Group 3
MH/MR/MMR/JPEG
Automatic Fallback
33,600 bps
ADF Width: 89 mm to 215.9 mm (3.5 in. to 8.5 in.)
ADF Height: 127 mm to 355.6 mm (5 in. to 14 in.)
208 mm (8.2 in.)
204 mm (8.03 in.)
256 levels
Standard, Secure, Timer Sequential: (Monochrome only)
Automatic/Light/Dark
(manual setting)
Horizontal 8 dot/mm (203 dot/in.)
Vertical
Standard
3.85 line/mm (98 line/in.) (Mono)
7.7 line/mm (196 line/in.) (Colour)
Fine
7.7 line/mm (196 line/in.) (Mono/Colour)
Photo
7.7 line/mm (196 line/in.) (Mono)
Superfine
15.4 line/mm (392 line/in.) (Mono)
100 stations
10 stations
160 stations
3 times at 5 minute intervals
0, 1, 2, 3, 4, 5, 6, 7 or 8 rings
(1, 2, 3 or 4 rings - Ireland only)
Public switched telephone network.
Up to 200
pages
Up to 200
pages
1
2
‘Pages’ refers to the ‘Brother Standard Chart No. 1’ (a typical business letter, Standard resolution, MMR code).
Specifications and printed materials are subject to change without prior notice.
‘Pages’ refers to the ‘ITU-T Test Chart #1’ (a typical business letter, Standard resolution, MMR code). Specifications and printed materials are subject to change without prior notice.
D
106
Specifications
Copy
Colour/Monochrome
Document Size
Copy Speed
Multiple Copies
Enlarge/Reduce
Resolution
Yes/Yes
ADF Width: 89 mm to 215.9 mm (3.5 in. to 8.5 in.)
ADF Height: 127 mm to 355.6 mm (5 in. to 14 in.)
Mono: Up to 18 pages/minute (A4 paper)
Colour: Up to 16 pages/minute (A4 paper)
Stacks up to 99 pages
Sorts up to 99 pages (Monochrome only)
25% to 400% (in increments of 1%)
(Monochrome)
Scans up to 600 ×1200 dpi
Prints up to 1200 ×1200 dpi
(Colour)
Scans up to 600 ×1200 dpi
Prints up to 600 ×1200 dpi
1
Based on Brother standard pattern. (Fast mode/Stack Copy) Copy speeds vary with the complexity of the document.
D
107
Scanner
1
2
Colour/Monochrome
TWAIN Compliant
WIA Compliant
Colour Depth
Resolution
Scanning Speed
Document Size
Scanning Width
Grey Scale
Yes/Yes
Yes (Windows
®
98/98SE/Me/2000 Professional/
XP
/Windows
®
XP Professional x64 Edition)
Mac OS
®
X 10.2.4 or greater
Yes (Windows
®
)
36 bit colour Processing (Input)
24 bit colour Processing (Output)
(Actual Input: 30 bit colour/Actual Output: 24 bit colour)
Up to 2400 × 2400 dpi (interpolated)
Up to 600 × 1200 dpi (optical)
Colour: up to 9.03 sec.
Mono: up to 4.05 sec.
(A4 size in 100 × 100 dpi)
ADF Width: 89 mm to 215.9 mm (3.5 in. to 8.5 in.)
ADF Height: 127 mm to 355.6 mm (5 in. to 14 in.)
210 mm (8.26 in.)
256 levels
Windows ® XP in this User’s Guide includes Windows ® XP Home Edition, Windows ® XP Professional, and
Windows
®
XP Professional x64 Edition.
Maximum 1200 × 1200 dpi scanning when using the WIA Driver for Windows ®
XP.
D
108
Specifications
Printer
Printer Driver
Resolution
Print Speed
Printing Width
Windows
®
98/98SE/Me/2000 Professional and XP
Windows
®
XP Professional x64 Edition driver supporting
Brother Native Compression mode and bi-directional capability
For Mac OS
®
X 10.2.4 or greater: Brother Ink Driver
Up to 1200 × 6000 dpi
1200 × 2400 dpi
1200 × 1200 dpi
600 × 600 dpi
600 × 300 dpi
600 × 150 dpi
Mono: Up to 25 pages/minute (A4 paper)
Colour: Up to 20 pages/minute (A4 paper)
204 mm (210 mm)
1
2
3
4
5
Disk-Based Fonts
Borderless
35 TrueType
Letter, A4, A6, Photo Card, Index Card, Post Card
Windows
®
XP in this User’s Guide includes Windows
®
XP Home Edition, Windows
XP Professional x64 Edition.
®
XP Professional, and Windows
®
Output image quality varies based on many factors including, but not limited to input image resolution and quality and print media.
Based on Brother standard pattern. A4 size in draft mode.
When you set the Borderless feature to On.
See Paper type and size for each operation on page 9.
Interface
D
USB A USB 2.0 interface cable that is no longer than 6 feet
(2.0 m).
1
2
Your machine has a full-speed USB 2.0 interface. This interface is compatible with USB 2.0; however, the maximum data transfer rate will be 12 Mbits/s. The machine can also be connected to a computer that has a USB 1.1 interface.
Third party USB ports are not supported for Macintosh ® .
D
109
Computer requirements
Computer Platform
& Operating System
Version
Windows
Operating
Systems
Me
2000
Professional
Minimum System Requirements
Supported
PC
Software
Functions
98, 98SE Printing,
PC-FAX Send
Scanning
PC
Interface
USB
Processor
Minimum
Speed
Intel
®
Pentium or equivalent
®
II
Minimum
RAM
64 MB
Recommended
RAM
256 MB
Available Hard
Disk Space for
Drivers for
Applications
32 MB 128 MB 120 MB 130 MB
XP Home 128 MB 256 MB 170 MB 220 MB
XP Professional
XP Professional x64 Edition
AMD Opteron™
AMD Athlon™64
256 MB 512 MB 170 MB 220 MB
Intel
®
Xeon™ with Intel
®
EM64T
Apple
®
Macintosh
®
Operating
Systems
1
2
3
OS
X 10.2.4 or greater
Printing,
PC-FAX Send
Scanning
Microsoft
®
Internet Explorer 5 or greater.
Third party USB ports are not supported.
PC Fax supports black and white faxing only.
USB
Intel
®
Pentium
®
4 with Intel
®
EM64T
Power PC
G3/G4/G5, Intel
®
Core™ Solo/Duo.
350MHz
128 MB 256 MB 80 MB 200 MB
For the latest driver updates, access the Brother Solutions Center at http://solutions.brother.com
D
110
Specifications
Consumable items
Ink
Service Life of Ink
Cartridge
Replacement
Consumables
The machine uses individual Black, Yellow, Cyan and Magenta ink cartridges that are separate from the print head assembly.
Black - Approximately 500 pages at 5% coverage Yellow, Cyan and
Magenta - Approximately 400 pages at 5% coverage
The first time you install a set of ink cartridge the machine will use an amount of ink to fill the ink delivery tubes for high quality print outs. This process will only happen once. With all following ink cartridge you can print the specified number of pages.
The above figures assume continuous printing at a resolution of
600 x 600 dpi in normal mode after installing new ink cartridge.
The number of pages a cartridge will print may change depending on how often you use the machine and how many pages you print with each use.
The machine will automatically and periodically clean the print head assembly, a process that uses a small amount of ink.
When the machine identifies a cartridge as empty there may be a small amount of ink left in it. This is necessary to prevent air from drying out and damaging the print head assembly.
<Black> LC1000BK, <Yellow> LC1000Y, <Cyan> LC1000C,
<Magenta>LC1000M
D
111
E
Glossary
This is a comprehensive list of features and terms that appear in Brother manuals. Availability of these features depends on the model you purchased.
ADF (automatic document feeder)
The document can be placed in the ADF and scanned one page at a time automatically.
Auto Reduction
Reduces the size of incoming faxes.
Automatic fax transmission
Sending a fax without picking up the handset of an external phone.
Automatic Redial
A feature that enables your machine to redial the last fax number after five minutes if the fax did not go through because the line was busy.
Backup Print
Your machine prints a copy of every fax that is received and stored in memory.This is a safety feature so you will not lose messages during a power failure.
Batch Transmission
(Black and white faxes only) As a cost saving feature, all delayed faxes to the same fax number can be sent as one transmission.
Beeper Volume
Volume setting for the beep when you press a key or make an error.
Brightness
Changing the Brightness makes the whole image lighter or darker.
Broadcasting
The ability to send the same fax message to more than one location.
Caller ID
A service purchased from the telephone company that lets you see the number (or name) of the party calling you.
Cancel Job
Cancels a programmed job, like Delayed
Fax or Polling.
CNG tones
The special tones (beeps) sent by fax machines during automatic transmission to tell the receiving machine that a fax machine is calling.
Coding method
Method of coding the information contained in the document. All fax machines must use a minimum standard of Modified Huffman (MH). Your machine is capable of greater compression methods, Modified Read (MR), Modified
Modified Read (MMR) and JPEG, if the receiving machine has the same capability.
Communication error (Comm. Error)
An error during fax sending or receiving, usually caused by line noise or static.
Compatibility group
The ability of one fax unit to communicate with another. Compatibility is assured between ITU-T Groups.
Contrast
Setting to compensate for dark or light documents, by making faxes or copies of dark documents lighter and light documents darker.
Delayed Fax
Sends your fax later at a specified time.
Dual Access
Your machine can scan outgoing faxes or scheduled jobs into memory at the same time it is sending a fax from memory or receiving or printing an incoming fax.
E
112
ECM (Error Correction Mode)
Detects errors during fax transmission and resends the pages of the fax that had an error.
Extension phone
A telephone using the same line as your fax but plugged into a separate wall socket.
External phone
A TAD (telephone answering device) or telephone that is connected to your machine.
F/T Ring Time
The length of time that the Brother machine rings (when the Receive Mode setting is Fax/Tel) to notify you to pick up a voice call that it answered.
Fax Detect
Enables your machine to respond to CNG tones if you interrupt a fax call by answering it.
Fax Forwarding
Sends a fax received into the memory to another pre-programmed fax number.
Fax Journal
Lists information about the last 200 incoming and outgoing faxes. TX means
Transmit. RX means Receive.
Fax Receive Code
Press this code (l 5 1) when you answer a fax call on an extension or external phone.
Fax Storage
You can store received faxes in the memory.
Fax tones
The signals sent by sending and receiving fax machines while communicating information.
Fax/Tel
You can receive faxes and telephone calls. Do not use this mode if you are using a telephone answering device
(TAD).
Glossary
Fine resolution
Resolution is 203 × 196 dpi. It is used for small print and graphs.
Grey scale
The shades of grey available for copying, scanning and faxing photographs.
Group number
A combination of One-Touch and
Speed-Dial numbers that are stored on a
One-Touch key or a Speed-Dial location for Broadcasting.
Help list
A printout of the complete Menu table that you can use to program your machine when you do not have the User's Guide with you.
Journal Period
The pre-programmed time period between automatically printed Fax
Journal Reports. You can print the Fax
Journal on demand without interrupting the cycle.
LCD (liquid crystal display)
The display screen on the machine that shows interactive messages during
On-Screen Programming and shows the date and time when the machine is idle.
Manual fax
On some models you can dial a fax number and listen to the receiving fax machine answer your call before you press Mono Start or Colour Start to begin sending the fax.
Menu mode
Programming mode for changing your machine's settings.
OCR (optical character recognition)
The bundled (ScanSoft
®
Paperport
®
SE with OCR or Presto!
®
PageManager) software application converts an image of text to text you can edit.
113
One-Touch
Keys on the machine’s control panel where you can store numbers for easy dialing. You can store a second number on each key if you press Shift and the
One-Touch Key together.
Out of Paper Reception
Receives faxes into the machine's memory when the machine is out of paper.
Overseas Mode
Makes temporary changes to the fax tones to accommodate noise and static on overseas phone lines.
Pause
Allows you to place a 3.5 second delay in the dialling sequence stored on
One-Touch and Speed-Dial numbers.
Press Redial/Pause as many times as needed for longer pauses.
Polling
The process of a fax machine calling another fax machine to retrieve waiting a fax.
Pulse
A form of rotary dialling on a telephone line.
Quick Dial List
A listing of names and numbers stored in
One-Touch and Speed-Dial memory, in numerical order.
Real Time Transmission
When memory is full, you can send faxes in real time.
Remaining jobs
You can check which jobs are waiting in memory and cancel jobs individually.
Remote Access Code
Your own four-digit code (---l) that allows you to call and access your machine from a remote location.
Remote Retrieval Access
The ability to access your machine remotely from a touch tone phone.
114
Resolution
The number of vertical and horizontal lines per inch. See: Standard, Fine, Super Fine and Photo.
Ring Delay
The number of rings before the machine answers in Fax Only and Fax/Tel modes.
Ring Volume
Volume setting for the machine's ring.
Scanning
The process of sending an electronic image of a paper document into your computer.
Search
An electronic, alphabetical listing of stored
One-Touch, Speed-Dial and Group numbers.
Speed-Dial
A pre-programmed number for easy dialling. You must press
Search/Speed Dial, #, the two digit code, and Mono Start or Colour Start to start the dialling process.
Standard resolution
203 × 97 dpi. It is used for regular size text and quickest transmission.
Station ID
The stored information that appears on the top of faxed pages. It includes the sender's name and fax number.
Super Fine resolution
392 × 203 dpi. Best for very small print and line art.
TAD (telephone answering device)
You can connect an external TAD to your machine.
Telephone Answer Code
(For Fax/Tel mode only)
When the machine answers a voice call, it pseudo/double-rings. You can pick up at an extension phone by pressing this code
(# 5 1).
Temporary settings
You can choose certain options for each fax transmission and copy without changing the default settings.
Tone
A form of dialling on the telephone line used for Touch Tone telephones.
Transmission
The process of sending faxes over the phone lines from your machine to the receiving fax machine.
User Settings
A printed report that shows the current settings of the machine.
Xmit Report (Transmission Verification
Report)
A listing for each fax sent, that shows its date, time and number.
Glossary
115
F
Index
A
ADF (automatic document feeder)
Answering machine (TAD)
connecting
.............................................35
Apple
®
Macintosh
®
See Software User's Guide on the
CD-ROM.
..................................................
Automatic fax receive
.............................................27
Fax Detect
..........................................30
B
Broadcasting
............................................22
setting up Groups for
............................42
C
Caller ID
...................................................33
print list
..................................................33
view list
.................................................33
Canceling jobs awaiting redial
...............................26
Cleaning paper pick-up roller
...............................89
print head
..............................................90
printer platen
.........................................89
scanner
.................................................88
Connecting external TAD
.........................................35
external telephone
................................36
Consumable items
.................................111
Control panel overview
..............................4
ControlCenter
See Software User's Guide on the
CD-ROM.
..................................................
Copy color adjustment
....................................61
enlarge/reduce
......................................58
enter Copy mode
..................................56
keys
.......................................................57
multiple
..................................................56
paper
.....................................................61
quality
....................................................58
single
.....................................................56
sort
........................................................60
116 temporary settings
................................ 57
using ADF
............................................. 56
Copy Options key (copying) paper size
............................................. 62
paper type
............................................ 61
Custom telephone features on a single line
............................................. 77
D
Dialing a pause
................................................. 40
Groups
.................................................. 22
manual
.................................................. 39
One-Touch
........................................... 39
Speed-Dial
............................................ 39
Dual Access
............................................ 24
E
Envelopes
......................................9
Error messages on LCD
Change Unable
.................................... 79
Clean Unable
........................................ 79
Comm. Error
......................................... 79
Init. Unable
........................................... 79
Ink Empty
............................................. 80
Near Empty
.......................................... 80
No Paper Fed
....................................... 80
Not Registered
..................................... 39
Out of Memory
...................................... 81
Print Unable
.......................................... 79
Scan Unable
......................................... 79
Extension telephone, using
External telephone, connecting
F
Fax codes changing
........................................ 38 ,
Fax Receive Code
......................... 36 ,
Remote Access Code
Telephone Answer Code
Fax Detect
................................................30
Fax Forwarding changing remotely
......................... 47 ,
programming a number
turning off
..............................................45
turning on
..............................................44
Fax Storage
.............................................44
turning off
..............................................45
turning on
..............................................44
Fax, from PC
See Software User's Guide on the
CD-ROM.
..................................................
Fax, stand-alone receiving
...............................................27
at end of conversation
difficulties
.................................... 74 ,
F/T Ring Time, setting
Fax Forwarding
..................................48
from extension phone
phone line interference
Receive Mode, choosing
reducing to fit on paper
retrieving from a remote site
Ring Delay, setting
.............................29
sending
.......................................... 22 ,
at end of conversation
Broadcasting
......................................22
canceling from memory
contrast
..............................................23
delayed batch transmission
delayed fax
........................................25
enter Fax mode
..................................22
from memory (Dual Access)
manual
...............................................26
overseas
............................................25
phone line interference
Real Time Transmission
Resolution
..........................................23
Fax/Tel mode answering at extension phones
,
double-ringing (voice calls)
F/T Ring Time
...................................... 29
Fax Receive Code
,
Ring Delay
............................................ 29
Telephone Answer Code
,
G
Gray scale
..................................... 106
Groups for Broadcasting
I
H
HELP
LCD messages
..................................... 94
using menu keys
............................... 95
Menu Table
.......................................... 94
Ink cartridges checking ink volume
............................. 92
ink dot counter
...................................... 85
replacing
............................................... 85
J
Jacks
EXT external telephone
............................. 35
TAD (answering machine)
Jams document
............................................. 82
paper
.................................................... 82
L
LCD (liquid crystal display)
,
Contrast
................................................ 18
Help List
............................................... 50
117
M
Macintosh
®
See Software User's Guide on the
CD-ROM.
..................................................
Maintenance, routine
...............................85
Manual dialing
....................................................39
receive
..................................................27
transmission
..........................................26
Memory Storage
......................................94
Menu Table
..............................................94
Mode, entering
Copy
......................................................56
Fax
........................................................22
Scan
........................................................5
Multi-line connections (PBX)
O
One-Touch changing
...............................................42
setting up
..............................................41
using
.....................................................39
Out of Memory message
P
Packing and shipping the machine
Paper
................................................ 7
capacity
.................................................10
document size
.........................................6
loading
........................................... 11
size
................................................... 9
type
.................................................. 9
PaperPort
®
SE with OCR
See Software User's Guide on the
CD-ROM.
..................................................
Phone line connections
...........................................35
difficulties
..............................................76
multi-line (PBX)
.....................................36
Phone line interference
............................85
Photo paper
.................................... 7 ,
Power failure
............................................94
Print area
...................................................... 15
checking alignment
............................... 90
difficulties
........................................ 74 ,
drivers
................................................. 109
improving quality
.................................. 90
paper jams
............................................ 83
reports
.................................................. 50
resolution
............................................ 109
specifications
...................................... 109
Printing
See Software User's Guide on the
CD-ROM.
..................................................
Programming your machine
Q
Quick-Dial
Broadcasting
........................................ 22
using Groups
..................................... 22
Group dial changing
............................................ 42
setting up Groups for Broadcasting
One-Touch changing
............................................ 42
setting up
........................................... 41
using
.................................................. 39
Search
.................................................. 40
Speed-Dial changing
............................................ 42
setting up by location
using
.................................................. 39
R
Receive Mode
......................................... 27
External TAD
........................................ 27
Fax Only
............................................... 27
Fax/Tel
................................................. 27
Manual
.................................................. 27
Redial/Pause
........................................... 40
Reducing copies
................................................... 58
incoming faxes
..................................... 30
Remote Retrieval
..................................... 45
access code
................................... 45 ,
commands
............................................ 48
getting your faxes
................................. 46
118
Remote Setup
See Software User's Guide on the
CD-ROM.
..................................................
Reports
....................................................49
Caller ID List
.........................................33
Fax Journal
...........................................50
Journal Period
....................................49
Help List
................................................50
how to print
...........................................50
Quick-Dial List
.......................................50
Transmission Verification
User Settings
........................................50
Resolution copy
....................................................107
fax
.......................................................106
.....................................................109
scan
....................................................108
setting for next fax
................................23
Ring Delay, setting
...................................29
S
Safety Instructions
...................................70
Scanning
See Software User's Guide on the
CD-ROM.
..................................................
Serial Number
how to find ...............See inside front cover
Shipping the machine
..............................92
Speed-Dial changing
...............................................42
setting up
..............................................41
using
.....................................................39
T
TAD (telephone answering device), external
............................................. 27 ,
connecting
............................................35
receive mode
........................................27
recording OGM
.....................................35
Temporary copy settings
Text, entering
.........................................102
special characters
...............................102
Transferring your faxes or Fax Journal
Transparencies
............................... 7
Troubleshooting
....................................... 74
checking ink volume
............................. 92
document jam
....................................... 82
error messages on LCD
if you are having difficulty copying
.............................................. 78
document jam
.................................... 82
incoming calls
.................................... 77
phone line or connections
printing
.............................................. 74
printing receiving faxes
receiving faxes
.................................. 76
scanning
............................................ 78
sending faxes
.................................... 77
software
............................................. 78
paper jam
............................................. 83
print quality
........................................... 90
TX Lock
................................................... 20
V
Volume, setting beeper
.................................................. 18
ring
....................................................... 17
speaker
................................................ 18
W
Windows
®
See Software User's Guide on the
CD-ROM.
.................................................
119
Visit us on the World Wide Web http://www.brother.com
This machine is approved for use in the country of purchase only. Local Brother companies or their dealers will only support machines purchased in their own countries.
UK/IRE/GEN
Advertisement