advertisement
Valet SmartCentre
Video Intercom System
Contents
Installation Manual
Welcome to Valet Inside front cover
Contents 1
Installation Guide Section 2
3
Wiring diagrams and schematics 5-10
System power supply 11
Voltage Chart 12
Installation 13-14
Operating Guide
User Guide Section 15
System operating guide 16
Operation, care instruction 20
20
Product Warranty Inside back cover
1
Valet SmartCentre
Video Intercom System
2
Monitor
14
9
2 3
10 11 12 13
4 5 6
1
7
8
1. LCD Screen
2. On/Off Button
3 Monitor/Answer Button
4. Intercom Button
5. Adjustment: Left/Right
6. Image Capture (if fi tted)
7. Door Release (if fi tted)
8. Speaker
9. Power Indicator
10. Intercom Busy Indicator
11. Talk Volume Indicator
12. Chime Volume Indicator
13. Door Release Indicator
14. Microphone
Dimensions: 180mm (H) x 258mm (W) x 91mm
J5
J8
Rear (Cut-Out) Dimensions
J9
Dimensions: 132mm (H) x 220mm (W) x 91mm (D)
Camera
5
1
4
2
1. Camera
2. Infrared LED
3. Speaker
4. Call Button
5. Microphone
3
3
Valet SmartCentre
Video Intercom System
Cable Confi guration Chart
Please use the chart below to select the correct wiring diagram to support your installation. Please ensure you also use the recommended Valet cable for the appropriate installation. Valet has many years of experience in installations of both Audio and Video. The cable distance can often have a detrimental impact on audio and video quality together with loss of voltage to critical operations.
We recommend the Valet 8 cable. This cable has 8 cores, 2 of which are shielded and should be used for Audio / Video signals to protect both clarity of image and quality of audio. The other cores give much greater fl exibility for your installation and can be doubled up in long cable run distances to ensure correct voltage and correct operation of electric door release signals.
K
L
M
H
I
J
Number of
A
B
C
F
G
D
E
Monitors Cameras Door
Release
1
1
1
Wiring Diagram & System Confi guration
The wiring chart below is for Video Intercom ONLY
1
1
2
No
1
No
Cable
Cores
6
6
6
Cable
Recommended
Valet 8
Valet 8
Valet 8
Cable
Recommended
Valet Cable
Core
To all camera
To all camera
35200009
35200009
To all Monitors/camera 35200009
2
2
1
1
1
1
2
2
2
2
2
2
No
1
2 2
Monitors in System 2 - 8
2
1
2
No
1
3
8
2
2
8
8
8
8
8
6
6
8
8
8
Valet 8
Valet 8
Valet 8
Valet 8
Valet 8
Valet 8
Valet 8
Valet 8
Valet 8
Valet 8
To all Monitors/camera 35200009
To all Monitors/camera 35200009
To all Monitors/camera 35200009
To all Monitors/camera 35200009
To all Monitors/camera 35200009
To all Monitors/camera 35200009
To all Monitors/camera 35200009
To all Monitors/camera 35200009
To all Monitors/camera 35200009
To all Monitors/camera 35200009
If Upgrade Kit to CCTV/TV/Alarm Interface/Image is likely then Valet Smart Wire Composite must be used.
This ensures all Video signals are protected from interference as well as control voltage drop by pairing for certain confi gurations.
Please see Upgrade Kit wiring chart and confi guration guide.
4
Valet SmartCentre
Video Intercom System
Wiring Diagrams and Schematics
• Cable and Connections for Doorbell/Camera
• 1R+ 12V power supply positive for Doorbell/camera.
• 2W: GND power supply ground for Doorbell/camera.
• 3Y: VIDEO image signal transmitting line.
• 4B: AUDIO audio and control lines.
• Cable and Connections for Monitor
• Connection block J5:
Vin, GND: Terminals for Power Supply Input.
GND, VD: Terminals for loop resistor if only one monitor, please short them.
PWR, GND, AU1, VD1, LOCK1+(SDOOR1): Terminals for Power supply/Ground/Audio/Video/Unlock
for the Doorbell/camera1.
• Connection Block J8
PWR, GND, AU2, VD2, LOCK2+( SDOOR2) : Terminals for Power supply/Ground/Audio/Video/Unlock
for the Doorbell/camera2.
•
Connection Block J9
•
Vin, GND, DATA, AUD, VD, GND Output Terminals for additional Monitors.
J5
J8
Rear (Cut-Out) Dimensions
J9
Dimensions: 132mm (H) x 220mm (W) x 91mm (D)
5
Valet SmartCentre
Video Intercom System
SINGLE CAMERA
SINGLE MONITOR
WITH DOOR LATCH
6
2 CAMERAS
SINGLE MONITOR
Valet SmartCentre
Video Intercom System
2 CAMERAS
MULTIPLE MONITORS
2 CAMERAS, 2 LATCHES
MULTIPLE MONITORS
7
Valet SmartCentre
Video Intercom System
SINGLE CAMERA
SINGLE MONITOR
8
2 CAMERAS, 2 LATCHES
SINGLE MONITOR
Valet SmartCentre
Video Intercom System
9
10
Valet SmartCentre
Video Intercom System
Valet SmartCentre
Video Intercom System
System Power Supply
• Multiple Monitor Systems require an upgraded power supply. Please see below the recommended options available from your local Valet Dealer.
• Each Monitor can use a separate single unit power pack or up to 8 monitors can be powered by a
multi-power supply to the Main monitor and then star wired to the other Monitors. Star wiring of a multiple monitor system is the most effective method. A loop confi guration is possible, but you need to establish the formula of voltage drop as each monitor is looped ( effective transmission distance is dramatically reduced in a loop confi guration).
• Please see the recommended Valet Cable to ensure to optimise your cable network
• When fi tting Electronic Door Releases or Latches please ensure you chose a model with it own power
supply. Your Valet SmartCentre Intercom delivers the open / close signal only.
• Valet Power Supply
• P/C 31111111 2 amp 18v DC Single Systems
• P/C 31111111 20 amp 18v DC Multi-systems
11
Valet SmartCentre
Video Intercom System
PLEASE READ AND UNDERSTAND THE FOLLOWING
Before installing the Valet Video System we advise that you consult the table below and take into account the various losses that can occur.
Failure to do this could result in loss of quality and poor performance.
Valet will not be responsible if this information is not strictly adhered too.
Device
Camera
Monitor
Door
Latch
Permissable Cable Length to Voltage drop
Current Cable
Demand Length
AMPS
0.11
0.12
0.16
25.00
0.47
0.26
0.23
Cable
Length
40.00
0.76
0.41
0.37
Cable
Length
75.00
1.42
0.77
0.69
Cable
Size
7/0.2
7/0.2
7/0.2
Cable Cable Permissible
Resistance Parallel Voltage Loss
0.086
0.086
0.086
1
2
3
2
2
2
0.6
0.6
0.6
0.3
0.5
1
1
2.58
1.29
1.29
0.65
0.54
2.15
1.08
4.13
2.06
2.06
1.03
0.86
1.72
3.87
3.87
1.94
1.61
7/0.2
7/0.2
14/0.2
14/0.2
14/0.2
14/0.2
14/0.2
0.086
0.086
0.043
0.043
0.043
0.043
0.043
1
2
1
2
1
2
1
3
3
3
3
3
3
3
Power
Supply
Amps
Permissable Power Cable Length to Voltage Drop Permissible
Amps
2
3
4
5
6
2.00
0.34
0.26
0.40
0.25
0.30
4.00
0.69
0.52
0.80
0.50
0.60
6.00
1.03
0.77
1.20
0.75
0.90
Size
14/0.2
14/0.2
24/0.2
24/0.2
24/0.2
Resistance
0.043
0.043
0.025
0.025
0.025
Parallel
1
2
1
2
2
Voltage Loss
1
1
1
1
1
* Length is calculated to Length / Resistance is Calcuated in Ohms Return (compisite resistance )
Demand No of
AMPS Monitors
0.6
1.2
1.8
2.4
3
3.6
4.2
4.8
1
2
3
4
5
6
7
8
This is a Voltage drop Chart
Maximum Permissable Voltage Drop
Reccomended Cable length for Signal is
Maximum Length
Monitor To Camera 50 Meters
Monitor to Monitor 40 Meters
Composite
Resistance
Value
0.09
0.04
0.03
0.09
0.04
0.04
0.04
0.02
0.04
0.02
0.04
0.02
0.03
0.01
0.01
12
Valet SmartCentre
Video Intercom System
SmartCentre Video Intercom Installation Instructions
Please see the relevant wiring diagram for the Smart Centre System you have chosen and ensure you have the correct cable for that systems requirements.
Single Camera to Single Monitor Installations:
1.1 Determine both SmartCentre Monitor and Doorbell/Camera operating positions and
heights. ( Average height 1.5 to 1.6 Metres ).
1.2 Run the appropriate cable between the two positions allowing at least 350mm excess at
each location.
1.3 Ensure you run cable through the appropriate back boxes if fi tted.
1.4 Unplug the connection terminal from the back of the monitor. ( Terminal J5).
1.5 Ensure power supply is disconnected at this point.
1.6 Connect cables as per the wiring diagram.
1.7 Re-connect terminal to rear of Monitor.
1.8 Remove top and bottom facia trim for mounting points Install the monitor to the wall or
mounting box if fi tted.
1.9 Power up when Doorbell/Camera is fi tted.
13
14
Valet SmartCentre
Video Intercom System
1 Single Doorbell/Camera:
2.1 Please take a moment to select the most suitable Doorbell/Camera position.
2.2 Please consider both daytime, night time and likely weather condition impact. Direct sunlight on the
camera and direct contact with rain should be avoided. Your Valet Dealer can assist you with
Weathershields for exposed positions.
2.3 Determine Camera Position: Please ensure you run cable through the camera mounting plate or back
box if fi tted. ( Average Height 1.5 to 1.6 metres ).
2.4 Both Surface Mount and Flush Mount Doorbell/Cameras require fi tting of each cameras mounting plate
or back box. Please check locating screws in top and bottom of Cameras.
2.5 The fl ush mount Camera requires a hole 75mm D x 50mm W at the desired location for the rear
camera housing and lens position adjuster. The Surface Mount Doorbell/Camera has an internal back
box that requires mounting on the wall.
2.6 Please ensure you run the cable through the mounting plate or back box
2.7 Connect your cable to the Doorbell/Camera following the wiring diagram .
2.8 Affi x the Doorbell/Camera onto its mounting plate or back box and secure with locator screws supplied.
Power up Intercom system when all connections are complete.
Valet SmartCentre
Video Intercom System
15
16
Valet SmartCentre
Video Intercom System
System Operating Guide
Please Note: The system must be set for the correct combination of monitors.
Each monitor is set as default to “MAIN”. Using system settings, set-up multiple monitor systems as one “MAIN” monitor and the additional monitors as “SUB”.
You must defi ne a primary Monitor as “MAIN” and additional Monitors as “SUB”.
When adjusting the set up of multiple monitor systems please set up ONE monitor at a time.
If two monitors are adjusted at the same time they may shut down for a short period and go into recovery mode, from which the setting may be lost and will need to be re-entered.
If power is lost or switched off, all system settings will be saved in memory. By entering set-up mode (press and hold Button 6) the power out time will remain in the display. However, the time and date clock will still run in the background.
Exit set-up mode and re-enter set-up mode and the current time will be displayed.
1. System Settings
At standby mode, press and hold “Photo Button” for 2 seconds to get into the set-up
SYSTEM SETTINGS
TIME 10-20-5 12:50:27
CHIME TIME 30S
CHIME VOL HIGH
TALK VOL HIGH
CHAR ADD ENABLE
INTERCOM SUB
TAKE PHOTO ENABLE
• 1
• 2 st
line: Day/Mth/Yr & Time for system nd
• 3 rd line: Chime DurationTime
line: Chime Volume (High/Low/Mute)
• 4
• 5 th
line: Talk Volume (High/Low) th line: CharacterAdd:Enable/Disable=
“DOOR1/DOOR2” on monitor screen )
• 6
• 7 th line: Main/Sub Multiple Monitor set up.
• HOLD button 6 on MAIN or SUB for 3 secs th
line: Photo Image Enable (optional)
Valet SmartCentre
Video Intercom System
1 Date and Time Set Up
The curser fl ashes at the fi rst character of Day, press “ ” (BUTTON 5) to change value, press
BUTTON 6 to move to the next value until both day/mth/yr and 24 hour clock is set.
Pressing BUTTON 6 will continue your progress through system settings until Intercom/Main menu.
Use BUTTON 5 to select Main or Sub.
At this point , hold BUTTON 6 for 3 secs, screen will then display the current setting mode of the photo image function, keep pressing this button to enable or disable the photo function ( only operates if
Image memory option is fi tted.
Press “On/Off” button 2 to “SAVE” system settings. Self turn off after 5 seconds.
The system settings will be recorded to memory when power is off.
2 Adjusting Chime Duration
The chime duration is preset at 30 seconds. If you wish to adjust this time:
The curser fl ashes at the fi rst character of Day, keep pressing BUTTON 6 to move to the chime duration setting.
Then press “ ” to adjust the chime time. The chime duration setting is from 10 – 90 seconds.
3 Adjusting Chime Volume
In standby mode, press “answer” BUTTON 3 for 2 seconds, the blue screen will show the defaulted
chime mode. Then press “ ”to adjust the chime volume to high, low or mute. E.g. fi gure below:
When the mute function is on, a red LED will light up on the monitor and the screen displays the word
“mute”. If you are called by other
CHIME VOL LOW
TALK VOL LOW
CHIME VOL HIGH
TALK VOL LOW
CHIME VOL MUTE
TALK VOL LOW
monitors or your visitors press
“call” button or Doorbell/Camera, function still works when the
mute function activated. Press “hang up” BUTTON 2 to turn off the screen, or it will be turned off
automatically after 5 seconds without pressing any button.
this monitor will remain mute.
However, the broadcasting
4 Adjusting Talk Volume
In standby mode, press “answer” BUTTON 3 for 2 seconds, the blue screen will display the current
talk volume. Keep pressing this button to adjust the talk volume. E.g fi g. below:
CHIME VOL HIGH
TALK VOL LOW
CHIME VOL HIGH
TALK VOL LOW
In this mode, with the current setting fl ashing, press BUTTON 6 to move adjustment from chime to the
talk setting. The defaulted talk volume is ”HIGH”. Press “ “ to adjust. If talk volume “LOW’ is
selected, a green light is displayed. Press BUTTON 2 to save and turn off the screen, or it will turn
off automatically after 5 seconds without pressing any buttons.
17
Valet SmartCentre
Video Intercom System
5 Brightness/Contrast/Colour
In standby mode press BUTTON 3 to display an image, press either adjustment ” “ button to adjust
the Brightness/Contrast/Color for the image.
In monitoring mode, keep pressing ” “ button back or forwards to adjust Brightness.
Press BUTTON 6 to move between Brightness Contrast & Colour Settings.
6 Call & Unlock function
When visitors press the Doorbell/Camera, the visitors image will show on the Monitor screen.
Press BUTTON 3 to stop the chime. You now have 60 seconds talk time (Set as default).
You can now talk to your visitor and determine if you wish to operate the door release if
fi tted BUTTON 7. The unlock signal will be sent to the electronic door release continually as
long as you press and hold the “Unlock” key. The shortest unlocking time is 1sec.
The Green /Red indicator lights will be on when the door is unlocked. Green Light for
the Doorbell/Camera1. Red light for the Doorbell/Camera2.
Door release button only operates during answering mode ie For security reasons it cannot
be operated at any other time ( accidental pressing).
If nobody answers the visitor, the system will stop chiming after preset time
(see system setting). A photo image of the Visitor can be saved in memory if you have chosen the
image store option.
If you wish to transfer the visitor to another person or to another area then the visitor audio video
image can be transferred to another monitor by the procedure below:
Press “call” BUTTON 4 on the monitor, all other monitors in the system will receive your call message,
eg. “Visitor for John”, John then presses the answer BUTTON 3 in the nearest monitor to see and talk
with the visitor.
7 Monitoring function : View Outside from Doorbell/Camera at any time
Pressing “Monitor” BUTTON 3 on any monitor will view the outside images from the Doorbell/Camera.
Green & Red lights will display for Camera 1 or 2 respectively.
The monitoring time is preset at 30sec.
8 Intercom function
In standby mode, a single press of BUTTON 4 from any monitor will call the other monitors.
Extension monitors will chime until any monitor answers by pressing button 3.
9 Broadcasting function to other monitors
At standby mode, press and hold “call” BUTTON 4 of any monitor to activate the broadcasting
function, while held down talk to all other monitors.
18
Valet SmartCentre
Video Intercom System
10 Photo function if fi tted
Description:
If after 10 seconds, there is no answer from the Monitor/Monitors the photo function will take
an image of the visitor and store it for later viewing. The date / time is also stored. Up to 8 images
can be stored. As new images are stored old images are deleted.
Operations:
In standby mode, press BUTTON 6 to view images from Doorbell/Camera. Image mode will return to
standby mode after 30 seconds.
19
20
Valet SmartCentre
Video Intercom System
Warranty and Care Instructions
1. Valet recommends an Authorised Valet Dealer should be used to install this Video Intercom System.
Please see your conditions of warranty. Call 1800-050-333 for your nearest Authorised Valet dealer and
installer.
2. Please ensure you use the recommended cable for the equipment set out in this guide.
3. Do not use cleaning agents or solvents on the Screens of these products. Use a moist damp cloth
and gently wipe lens surfaces outwards.
4 Image distortion may occur if your equipment is mounted too close to magnetic fi eld e.g. Microwaves,
TV, Audio equipment or speakers.
5 The Doorbell/Camera should be fi tted with an approved weather shield if the position chosen is in
direct sunlight, or in contact with rain, snow or irrigation sprinkler systems.
Technical Specifi cations:
The Valet Smart Centre Video Intercom may work with cable and products not recommended or known to Valet. However, Valet warrants its product to work as per its specifi cation if the recommended cable is used and the wiring instructions are followed.
Monitor
Display screen 5 inch TFT
Resolution > 400 TV lines
Scan frequency 15,625Hz (H)×50Hz(V)
Power voltage DC 18V
Video input 75 ohms 1Vp-p CCIR standard
Power consumption 1.5w 12 w
Wiring mode See Charts
Dimension 258mm(W)×180mm(H)×91mm(D)
Doorbell/Camera
Camera 1/3 inch colour
Resolution 380 TV lines or <380 TV lines
Video output 75 ohms 1Vp-p CCIR standard
View angle 78-degree wide-angle camera
Min illumination 0 Lux
Night vision light 6 infrared LED
Power voltage DC 12v
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project