Technomate TM-5000 HD Satellite Receiver User manual

& Technomate
|
/ Table of Contents
HD) INTRODUCTION 2
Overview
Main Features
[A] EASY INSTALLATION GUIDE 3
EL) SAFETY INFORMATION 6
2% CHECK POINTS BEFORE USE 8
Accessories
Satellite Dish
<> CONTROLS/FUNCTIONS ?
Front Panel
RearPanel
Remote control
o EQUIPMENT CONNECTION 13
Connection With Antenna/ TV Set/ A/V System
OPERATION 14
Getting Started
System Settings
Edit Channels
EPG (Electronic Programme Guide)
Games
USB Menu (How to download SW from USB)
PVR
System Information
F X Common Interface
Y Disposal of Old Electrical £ Electronic Equipment(Applicable in the European Union
and other European countries with separate collection systems) AM J HOWTO DOWNLOAD SOFTWARE FROM PC 39
This symbol on the product or on its packaging indicates that this product shall not be р
as household waste. Instead it shall be handed over to the applicable collection point for the
BE ccycling of electrical and electronic equipment. By ensuring this product is disposed of 9] TROUBLE SHOOTING 42
correctly, you will help prevent potential negative consequences for the environment and -
human health, cH he EI be caused by map riate waste handling of this
product, The recycling of materials will help to conserve natural resources. = |
For more detailed information about recycling of this product, please contact yourlacal city SPECIFICATIONS 44
office, your household waste disposal service or the shop where you purchased the product. J
—
=
Бо
E
~
о
BH (BRIEF USER'S GUIDE IN FRENCH 46)
www. technomate.
& Technomate & Technomate
FE) INTRODUCTION [)] EASY INSTALLATION GUIDE
9 OVERVIEW PART 1 Using the Preinstalled Satellite 8%: Channel List
This satellite receiver is designed for using both free-to-air and encrypted channel reception depending on model variant .
Enjoy the rich choice of more than 10,000 different channels, broadcasting a large range of culture, sports, cinema, news, The receiver is preinstalled with 25 Satellites and 1500 default Channels and is fully
events, etc. This receiver is a technical masterpiece, assembled with the higfest quality electronic parts. configured. Only motor settings need to be changed '
After turning ON the receiver, select a language. You will be taken to the Viewing
© MAIN FEATURES mode. Press the SAT button on the Remote and select a Satellite. To bring up the
} High-Definition Personal Video Recorder (HD PVR) Channel List, press the OK button on the remote on the desired satelite.
} DVB-S/DVB-S2 Satellite Tuners (MPEG-2, MPEG-4 & H.264) To delete unwanted Satellites- press the MENU button on the remote and go fo
> Output resolution : 576p & 576i, 720p, 1080p & 1080 Installation. Press OK and OK on Satellite Setup. Press OK again and a Satellite
} 1 Smart Card Reader & 1 Common Interfaces (1C1) List will appear. To delete a Satellite, press the BLUE (E) button on the remote.
> HDMI & Component Output (YPbPr) with Upscaler to Improve Picture Qualify
» 10,000 TV & Radio Channels
» MP3 player and JPEG viewer via external HDD or USB flash Drive (memory stick)
> Software 4 Channel List download via USB 2.0
How to Motorise 25 Satellites & 1500 EA NANA NS:
> Less than 7 second channel change The receiver is preinstalled with 25 Satellites and 1500 default Channels, and is also fully
b » Dolby Digital Optical § / PDIF configured, No settings need to be changed.
о N so EN Press the MENU button on the remote. Press OK on Installation. Go to Motorised Setting |
» On-screen display with true fui ARR and press OK. Go to the Third line (DISEGC Motor) and use the Left/Right arrow buttons
» Enhanced 16 Favourite channel groups on the remote fo select USALS. Then go to Position Setting and press OK. Then go fo
P Channel control by : Favourites, Lock, Skip, Move 4 Delete Longitude and Latitude and enter the coordinates of where you live (London's Longitude
> Channel sort by : AN, Alphavet, Transponder & CAS is 000.1 West; Lodon's Latitude is 51.5 North). Press the EXIT button on the remote. |
» Multilingual OSD Menv : English, Spanish, Portuguese, French, Dutch, German, Italian Turkish,
Arabic, Russian, Persian, Greek, Czech, Romanian
» Extended EPG and program reservation on EPG
Go to GOTO and press OK. Wait until the Signal Quality is more than 60% in the progress
bar, When a Satellite is found, then all the selected 25 Satellites are fully configured for
> Teletext 2 Subtitle by OSD and VBI a Motorised system.
p Last Channel mamayy mi-son If the Signal Quality is below 40%, then the settings are incorrect and the Longitude needs
E fo be adjusted, for example: 000.2, 000.3, 000.4,5/6/7/8/9 West or East. The Latitude may
» software 3 channel list upgrade vía RS-232C : PC to STB, STB o PC, STB-STB and USA TD lo + re If you still have nal got a signal, then the external installation
» Parental, Installation & Receiver Lock (dish, efc) needs to be adjusted.
» Zoom function on Pause & Live channel
» Mulfipicture display How to Setup a DISEqC 1.2 Motorised S
E En EE EE RS C/Ku smd satellites LNBs supported : Universal, Single, Press the MENU button on the remote and go to Installation and press OK. Goto
Single 5 4 C band wideband LNBs Motorised Setting and press OK. Press OK again to open the satellite list, Selecta
b AC 100-250V 50/60Hz satellite from the list and press OK. Go to the Third line (DISEQC Motor) and use the
» LNB Short Circuit protection onboard Left/Right buttons on the remote to select DISEQC 1.2, Go to Move and press and
+ 2 Scarts, (CVBS, RGB / Loop-through RGB) & S-Video hold the Left/Right buttons on the remote until you get a Signal Quality of more than
» USB 2.0 Ports: PVR function using extemal HDD, playback MP3, JPEG Photos 4 Software transfer 60%. Goto Save and press OK. Press the RED (E) button on the remote to Scan.
» Lan 10/100Mbps Ethernet To scan extra satellites, repeat the above.
> Blind Search
[XIDOLBY » Manufactured under license from Dolby Laboratories, PART 2 New Installation from start (NO Satellites/ Channels)
DIGITAL PLUS | "Dolby" and the double-D Symbol are trademarks of Dioby Laboratories.
How to do a Factory Reset to Delete the Prei
If you want to start the receiver without the preinstalled Satellites and Channels, press the
MENU button on the remote and go to System Settings and press the OK button, Go to
Factory Reset, press OK and enter 0000. Then select Factory Reset, Press OK and select Yes.
» DISEQC is a trademark ot EUTELSAT | stalled Satellites SG EATEN EE
—
E.
оч
OD IT TES TSE
—— 2 — A
& Technomate
How to Install a New Satellite (Fixed Non-Mt
Press the MENU bution on the remote and press the OK button on Installation. Press OK on
Satellite Setup and OK again to display a Satellite List. To add a Satellite, press the YELLOW
(C__J)button on the remote. Press the EXIT button on the remote to exit the list,
ad SYStem)
When the Quality Bar is at its highest level, press the RED (fad) button on the remote to Scan
the Satellite. To view a channel, press the OK button in the Viewing Mode (clear screen) and
select any channel. To view $ [Scrambled]) channels, a CAM (Decoder) and a viewing card
are required.
(0 180 & LNB EYL) BHED)
Press the MENU button on the remote and press the OK button on Installation. Press OK on
Satellite Setup and OK again to display a Satellite List. Select a Satellite (e.g. Hotbird 13E
and Astra 19.2E) and press the YELLOW button on the remote for each Satellite to Save. Press
the EXIT button on the remote to exit the list.
Go to DISEqC Switching and select a Satellite (e.g. Hotbird 13E as Number | and Astra 19,2E
as Number2). When the Quality Bar is at its highest level for each Satellite press yellow to
save, press the RED (jg ) Button on the remote to Scan. To view a channel, press the OK
button in the Viewing Mode (clear Screen) and select any channel. To view § (Scrambleed)
channels, a CAM (Decoder) and a viewing card are required.
How to Setup a Monoblock or DISEQC Swité!
If the above installation was not successful, change the DiSEqc Switching number, e.g.
Hotbird 13E as Number 2 and Astral 9E as Number 1.
Press the MENU button on the remote and press the OK button on Installation. Press OK on
Satellite Setup and OK again to display a Satellite List, Select a Satellite (e.g. Hotbird 13E
and Astra 19.2E) and press the YELLOW button on the remote for each Satellite to Save.
Press the EXIT button on the remote to exit the list.
Press the EXIT button again, Press OK on Motorised Setting. Press OK again ta display a
Satellite List. Select a Satellite and press OK, Go to the Third line (DISEQC Motor) and use
the Left/Right buttons on the remote to select DISEQC 1.2. Go to Move and press and hold
the Left/Right buttons on the remote until you get a Signal Quality of more than 60%. Go to
o press OK. Press the RED button on the remote to Scan, Repeat the above for more
satellites.
How to Setup a USALS Motorised System™
Press the MENU button on the remote and press the OK button on Installation. Press
OK on Satellite Setup and OK again to display a Satellite List. Select a Satellite (e.g.
Hotbird 13E and Astra 19.2E) and press the YELLOW ([__])button on the remote for
each Satellite to Save. Press the EXIT button on the remote to exit the list.
Press the EXIT button again. Go to Motorised Setting and press OK. Go to the Third
line (DISEQC Motor) and use the Left/Right arrow buttons on the remote to select
USALS. Then go to Position Setting and press OK. Then go to Longitude and Latitude
and enter the coordinates of where you live (London's Longitude is 000.1 West; Lodon's
Latitude is 51.5 North). Press the EXIT button on the remote. Go to GOTO and press
OK. Wait until the Signal Quality is more than 60% in the progress bar. Press the RED
(E) button on the remote ta Scan.
a {4
EZ Technomate
If the Signal Quality is below 60%, then the seftings are incorrect and the Longitude
needs to be adjusted, for example: 000.2, 000.3, 000.4,5/6/7/8/9 West or East.
The Latitude may also need to be adjusted. If you still have not got a signal. then
the external installation (dish, etc) needs to be adjusted.
How to restore default channels — =
Press MENU button on the remote. Go to Factory Reset, then go to Restore default channels.
Press OK button on the remote, and input password and wait.
[twill retrieve defaulf channels.
Active Transponders
For Technomate Motorized Systems
o.| Satellite Nome | Degree | Frequency | SymbolRate | Polarity
1 PAS 45 IR 45.0 W 11510 26694 H
2 TELESTAR 11 37.5 W 11494 19500 H
3 HISPASAT 30.0 W 1181] 27500 H
4 NSS803-K 21.5 W 11605 40000 H
5 INTEL 901 18.0 W 11673 28571 H
6 TELESTAR 12 15.0 W 11124 18386 H
7 ATLANTIC B1 12.5 W 11132 03255 H
8 EXPRESS 3A 11.0 W 11464 04340 V
9 TELECOM 2D 8.0 W 12747 02894 H
10 NILESAT 101 7.0 W 11747 27500 V
11 | ATLANTICBIRD 3 5.0 W 12543 27500 H
12 THOR 707 -2/3 1.0 W 11229 24500 H
13 SIRIUS 2 5.0 E 11766 27500 H
14 EUTEL W3 7.0 E 11263 27500 H
15 EUTEL WI 10.0 E 11526 30000 V
16 HOTBIRD 13.0 E 10892 27500 H
17 EUTEL W2 16.0 E 11304 30000 у
18 ASTRA | 19.2 E 12692 22000 H
19 ASTRA 3A 235 E 11634 27500 H
20 ARABSAT 2A 26.0 E 11958 27500 H
21 ASTRA 2 28.2 Е 11469 27500 H
22 EUTEL W4 36.0 E 12698 04340 H
23 HALLAS SAT 379.0 E 12524 29000 H
24 TURKSAT IC 42.0 E 12652 22500 H
25 EUROSTAR | 45.0 E 11500 04340 у
Z Technomate
TL, SAFETY INFORMATION _
Be sure to read the user's manual before Do not touch the power cord with wet
starting the operation of the unit. hands as it may cause electric shock.
to touch the inside of the unit due to the no-heat environment.
| Never open the cover. It is very dangerous Place the unit in a well ventilated and
possibility of an electric shock.
When you do not use this unit for a long
time, make sure that the power cord is pulled
out from the outlet. Also do not use a damaged
power cord as it may cause fire or electric shock
A professional installation is required. If
reception is interrupted, contact your
local service centre.
aus
@-Technomate
placement may cause the unit to be
damaged.
Place the unit horizontally. An uneven
the unit. This may damage the unit.
Do not put heavy items such as a TV on |
vase on the unit.
| Do not put water containing items such “|
Do not install the unit :
‘Where itis subject to vibrations.
‘Where it is exposed to direct sunlight.
‘Where there is humidity,
‘Where the temperature is too high or too low.
‘Where there is no ventilation.
Moving the unit to a hot area from a cold
one will cause condensation. Do not operate
the unit for one or two hours or until it has
dried completely.
The mains plug is used as the disconnect The disconnect device shall remain readily
device. operable.
& Technomate
ACCESSORIES
User's manual ; 1
SATELLITE DISH
=
—
a!
р
—
5
E
+
=
ko
A
~~
=
+
>
+
+
=
>
-
Ask your dealer for more information.
2% CHECK POINTS BEFORE USE
Remote control: 1
HDMI cable : 4
If any accessories listed above are
missing, contact the sales
representative where you
purchased this unit.
Your dish should be properly installed and azimuth and elevation must be precisely set up.
This unit is working with DiSEgC 1.2 on a compatible antenna positioner.
Za Technomate
E
7 CONTROLS/ FUNCTIONS
FRONT PANEL
“Technomate
mooiey HIM
DEN > SL FL ан
© 600
1. Standby /Power on indication light :
Red on stand-by mode and no light on power-on mode.
2. Remote command indication light :
By pressing any remote button, this light will flash at the same time.
3. Power:
To switch the receiverin stand-by mode orin power-on mode.
4. CH. (A/V):
To change channel or cursor position on the application screen.
=
=]
-
u
Ce
Ss
E
=
=
-
Ко
Ey
x
=
=
& Technomate
REAR PANEL
X 0004000041004
00040004000
- REMOTE CONTROL
o ©
O
ов
о
<
ee
|
[
0:
0:0:
A
di
р
——
0.0
Ne
-
eceec
e —
vw
—
a
E
x
=
7
ececéese 6
e
e
® ©) —— O vers
04000040004
as (GRE
courdient LAN wep, нм +
No. Name Connector | Function
] LNB INPUT IEC 169-24 female | IF input from LNB to digital tuner
LOOP OUT IEC 169-24 female IF loop-through output
from digital tuner
3 VIDEO RCA cinch Composite video outpul
4 AUDIO L RCA cinch Left audio output
5 AUDIO R RCA cinch Right audio output
6 Y RCA cinch Component video output (Y)
7 Pb RCA cinch Component video output (Pb)
8 Pr RCA cinch Component video output (Pr)
9 VCR/AUX SCART CVBS Video Output
SCART CVBS, RGB Video Input
Audio Output
10 TV SCART SCART CVBS, RGB Video Output
Audio Output
11 RS-232C DB-9 Low speed serial port
12 RF OUT UHF 21-69 IEC 169-2 MALE Output to TV
13 TV ANT IN IEC 169-2 female | Input from terrestrial antenna
14 S/PDIF Fiber Optic Digital audio output(Optic).
| 15 USB USB Receptacle A-Type USB Interface
Ч | 16 LAN RJ-45 10/100Mbps Ethernet
= 17 HDMI HDMI Digital Video/Audio Output
ETechnomate
TM-5000 HD Series
ty
@-Technomate
1. POWER: To turn the receiver On/Off
2. MUTE: To turn the sou
3. TV/RADIO:
To switch between TV and Radio
4. TV/SAT: To switch between the
satellite input and UHF/VHF
antenna input
5. EDIT: To go to Edit Channels Menu.
6. SLEEP: To turn the Unit off after a preset
time.
7. MOSAIC: To display multiple pictures.
8. FREEZE: Press once to pause live TV.
Press again toresume play.
9. ZOOM: Activates the zoom function.
10. UHF: To adjust UHF channe
11. Numeric Keys (0 - 9): To enter
numerical settings(such as channel
numbers) directly.
12. USB: To show the usb menu.
13. RECALL: To go to the previous
channel menu. Used for special
functions in menu mode.
14. MENU: To enter or exit the main menu.
15. EXIT: To exit from the present menu
and to go to the previous menu.
16. UP & DOWN: To change channels in
non-menu mode and move the cursor
up / down in menu mode.
17. LEFT & RIGHT: To change the volume
level in non-menu mode.
18. INFO: To show information about the
current program. Press twice to show
detailed information.
19. SAT: To show Satellite list.
bd
Бо
>
~
=
=
—añ
TU ZE 17172
& Technomate
\ REMOTE CONTROL
O:
©: ©: :0
\
hd
w
pe
2
90666666
>
IL
ETechnomate.
— TM-5000 HO Series ||
UD
ECGECECCOCCOS
С : E
20. PLAY: Play Content.
21. PAUSE: Pause playback.
22. REC: Start recording.
23. FILELIST: To display the filelist.
24. STOP: Stop Playback.
25. RWD: Rewind a file.
26. FWD: Forward a file.
27. SLOW: Playback in slow mode.
28. ADVANCE: Go to live channel.
29. Color Key: To use special functions
in the menu.
30. EPG: To show the TV/Radio program
guide.
31. FAV: To show favorite list in the favorite
group or fo move to the next page.
32. TEXT: To show the teletext contents if
teletext is transmitted. Used for
special functions in menu mode.
33. A-Z: To sort channel list.
34. AUDIO: To show Multi-language audio
track, the stereo-mono mode and
subtitle information. Used for special
functions in menu mode.
35. SUBTITLE: To show the subtitle contents
if subtitle is fransmitted.
36. Color: To control brightness, contrast
color of a picture (when in CVBS mode).
37. POS: To show the DISEQC motor view
control.
38. BOOKMARK: Set the bookmark position.
39. V.FORMAT: To change video output's
resolution.
40. Wide: To select a TV aspect ratio with
Pan Scan or Letter-Box(4:3)
(Full screen or Pillar box(16:9).
41. IP: To go to Set IP Menu.
42. F2: To display the Divx filelist
43. F3~F5: Reserved button for new
function.
& Technomate
áa
{> EQUIPMENT CONNECTION
CONNECTION WITH ANTENNA/ TV SET/ A/V SYSTEM
1. Connect the TV antenna to TV ANTIN.
2. Connect the RF-IN of TV to RF-OUT.
3. Connect the Video and Audio of TV to the Video and Audio.
Connect Red and White connector to Audio R and Audio L, and
Yellow into Video port respectively.
4. Connect the Component Video of your TV fo Component Video for best quality.
Connect the Y, Pb and Pr of your TV to Y, Pb and Prrespectively.
5, Connect your satellite dish.
6. Connect the USB storage device.
== т в — ан — A LE
RFIN ye Gy
SCART
L | Pb a)
Audio
R O
æ
a
U у ~
[à dès
E) = =
: = CC à 27
о © © ©
| © 3.6 6 D (reuvasennite
| (6 4 A \ i
| © © © lo CIAT
Tv me LOG A я U —
=" 1
* Note : In some receivers 1'V scart is at the top or bottom of the rear of the receiver
please follow the Writing of the TV then connect your scart cable for viewing.
fo.
Е
©
=
x
-
s
fy
=
-~
Ss
oy
bo
Lt
—
-
N
Lo
put
=
-
=
-
-
& Technomate
©) OPERATION
к той “2 A A
> GETTING STARTED
Turn your receiver power on and proceed with system setup as follows:
Menu Language Setting —
1. Turn on your TY and receiver.
2. The language selection menu will be
displayed, select a language and
press the OK button on.
1. Press the MENU button on the remote
to display the main menu.
2.Use 4/0 and A/Y button on the
remote to move in the menu.
3. Select Satellite Setup, the
Satellite Setup menu will appear.
& Technomate
4. Select each menu you want to edit/ change
- Satellite: Select any satellite by pressing
</ » buttons on the remote.
- Transponder: Displays the current TP value of the
selected satellite
- LNB Power: Select LNB power ON/OFF/13V/18V
- LNB Type: Selec! your LNB Type Single / Universal /OCS
- LNB Freq: Select LNB oscillator frequency.
- 22KHz: Select ON/ OFF of 0/22 KHz
- DISEgC 1.0: Select DISEgC 1.0 Port
= DISEqC 1.1 : Select DiSEqC 1.1 Рог!
5. Scan: Press Red ( Gi] )button on the remote to begin satellite search.
6. Rename: Press Green ( [Lu] )button on the remote to rename the selected satellite.
7. Auto Navigation: Press Green ( Ea] )button on the remote to begin auto navigation.
8. Save: Press Yellow ([__])button on the remote to save the selected satellite.
9. Delete: Press Blue ( [55] )button on the remote to de select the selected satellite.
Motorized Setting = =
1. Press the MENU button on the remote to
display the main menu.
2.Usethe 4/p and A/Y buttons onthe
remote to move in the menu,
3. Select Motorized Setting, the
Motorized Setting menu will appear.
4. Select each menu you want to edit / change.
- Satellite: Select any satellite by pressing </ P buttons on the remote.
- Transponder: Displays the current TP value of the selected satellite.
- DISEQC Motor: Select DISEQC Motor type OFF/1.2/USALS.
- Save: Press OK button on the remote to save.
5.S8can: Press Red (fal) button on the remote to begin satellite search.
6. Auto Navigation: Press Green (fa) button the remote to begin auto navigation.
—ûs
& Technomate & Technomate
1. Select DISEQC 1.2 on DISEQC Motor, the the DISEQC 1.2 menu will appear.
al - Satellite: Select any satellite by pressing 4/P buttons. |. Select DISEgC 1.2 or USALS in the
- Transponder: Displays the current TP value of the selected satellite. M zed Setit
- DISEgC Motor: Select DISEQC 1.2 otorized Setting menu.
- Move: Move the dish position to west/east by pressing </P buttons. а
- Move Fine: Move the dish position 1 step at a time to west/ east 2.1n the viewing mode, Press POS button
by pressing </» buttons. on the remote to display DISEqC Motor
- Motor Control : Control motor by press OK button on the remote. vi
nirol.
- Recalculate : Recalculate the position of all other saved satellites ew Control
relative to the known position.
- Rese! System : Reset the position of all saved satellites.
- Goto Reference: Move the dish to the 0 position. 3. Press </P buttons on the remote to
- Delete Limit: Delete east and west limit, .
- Enable Limit : Enable the saved east and west limit. move DISEgC Motor to get the best signal.
- Set East Limit: Edit 8. Save east limit by pressing 4/» or OK buttons.
- Set West Limit: Edit 8. Save west limit by pressing </» or OK buttons,
- Со To: Go to the position of the saved satellite.
- Save: Save the current setting of DISEQC 1.2 system.
DISEqC Motor View Control
2. Scan: Press Red (fl) button on the remote to begin satellite search. Auto Navigation
3. Auto Navigation: Press Green (Ea) button on the remote to begin auto navigation.
All the available channels/satellites can be searched in this menu. Select the
USALS System Setup | = satellite and save before Auto Search.
1. Select USALS on DISEQC Motor, the USALS menu will appear.
- Satellite: Select any satellite by pressing €4/» buttons.
- Transponder: Displays the current TP value of the selected satellite.
- DISEgC Motor: Select DISEgC Motor USALS.
- Move: Move the dish position fo West/East by pressing 4/» buttons.
- Motor Control : Control motor by press OK button on the remote.
- Goto Reference: Goto reference by pressing OK button.
Delete Limit: Delete limit by pressing OK button.
- Enable Limit : Enable the saved east and west límit.
- Set East Limit: Edit & Save east limit by pressing </» or OK buttons.
Set West Limit: Edit & Save west limit by pressing 4/» or OK buttons.
- Sat Degree: Displays the current degree of the selected satellite.
Edit degree by pressing </P buttons and numeric buttons,
- Position Setting: Select position setting by pressing OK button.
-Golo Reference: Move the dish to the O position.
-Antenna Longitude: Edit antenna longitude by pressing </P
buttons and numeric buttons.
-Antenna Latitude: Edit antenna latitude by pressing « / »
buttons and numeric buttons.
- Go To: Save the current setting of USALS System.
1. Press the MENU button on the remote to display
the main menu,
2. Use the 4/P anda/Y buttons to move in
the menu.
3. Select Auto Navigation, Auto Navigation
menu will appear.
4, Select the satellites you want to search by pressing the OK button on the remote.
You can select more satellites by pressing the </P button and OK button on the
remote.
- Search Type: Select the type of channel search you want by pressing </P buttons
ontheremote.
‘All: To search all the Free To Air and scrambled channels, TV & Radio channels.
2. Scan; Press Red (lal) button on the remote to begin satellite search. -Free: To search Free To Air channels only.
3. Auto Navigation: Press Green (fl) button the remote to begin auto navigation ‘TV: To search TV channels only.
‚ - Network Search: Select Network Search ON/ OFF to find more transponders through
* Note: When you change each parameter, you need to know exact parameter of the LNB to modify L.O(local oscillator) frequency. NIT Search
-@
Z Technomate
- Scan: Begin channel search of the selected
satellite.
5. Auto Navigation: Press Red ( a] )button
on the remote.
6. Auto Navigation Blind Search:
Press Green (gal) button on the remote to
begin channel search of all of the satellite
in the satellite list.
* Note: Make sure that the signal level of the selected satellites is high by the signal quality bar. If the signal quality is lower
than 50%, go back to Satellite Setup and check LNB, DiSEqC Switching, etc.
Blind Search EZ
Provides easier and thorough channel search option to users
1. Press the MENU button on the remote to display
the main menu.
LES 7 т
ETE
po +.
PE
2. Use the </> and A/V buttons to move in
the menu.
3. Select Blind Search, the Blind Search menu
will appear.
A. Select the satellites you want to search by
pressing OK button on the remote.
You can select more satellites by pressing «< /»
bution and then the OK button on the remote.
- Satellite List: Select satellite that you want to search,
- TP : Select TP Frequency.
- Polarization : Select ALL / Vertical / Horizontal
- Mode : ALL / FREE / ТУ
- Scan: Begin channel search of the selected
satellite.
5. Auto Navigation Blind Search:
Press Red (m) button on the remote to
begin blind search of all of the satellite in
the satellite list. ;
Advance Search В
Te edit and search channels on newly launched satellites or not
preprogrammed satellites in the list.
18—
Z Technomate
1. Press the MENU button to display the
main menu.
2.Use </> and A/Y buttons to move
inthe menu.
3. Select Advance Search, the
Advance Search menu will appear.
4. Select each menu you want to edit/ change.
- Satellite: Select asatellite by pressing </P buttons on the remote,
- Transponder: Displays the current Transponder list of the selected satellite.
- Symbol Rate: Displays the current symbol rate list of the selected transponder.
- Polarization: Select Horizontal/ Vertical.
- Search Type: Select All Channel/ FTA Only/ TV Only.
- Network Search: Select Network Search ON/ OFF.
5. Scan: Press Red ( a] )button on the remote to begin satellite search.
6. Add TP: Press Green ( E] )button on the remote to add new transponders by
using numeric buttons 0-9 and </P» buttons on the remote.
7. Delete TP: Press Yellow ([_]))button on the remote to delete transponders.
PID Search
Edit the information of the current transponder PID/ Audio PID/ PCR PID and search
the satellite.
1. Press the MENU button on the remote to display
the main menu.
2.Use 4/p and A/Y buttons on the remote to
move in the menu.
3. Select PID Search, then the PID Search menu
will be displayed.
- Satellite: Select a transponder which you want to
search.
- Transponder: Displays the Transponders of the selected satellite.
- Symbol Rate: Displays the current symbol rate list of the selected transponder.
- Polarization: Select Vertical/ Horizontal.
- Video PID/ Audio PID/ PCR PID: Select and edit by using numeric buttons 0-9 and
4/» buttons on the remote.
& Technomate
4. Scan: Press Red (fa) button on the remote to begin PID Search.
5. Add TP: Press Green (fi) button on the remote to edit transponder by using
numeric buttons 0~9 and 4/» buttons on the remote.
* Note: Setup is now completed. If you cannot see the programme after finishing these procedures, please contact
your local dealer.
> Fast Scan
1. For Provider choose either Canal Digitaal or TV Viaanderen.
2. For CHs Renumber select ON/OFF
3, Press the Red (fal) Button.
Channel Selection
bp If you know the channel number, enter the
channel number by using numeric buttons
on the remote and wait 2 seconds until the
channel changes.
de TE
bp If you know the channel name, press OK
bufton on the remote, then the channel list
will be displayed. Select the channel you
want to watch by using 4/Y, OK buttons on DA jur |
the remote. == вы у
"
Ë
Е |3
т
1. Inthe right side of screen, detailed information of the selected channel is
| displayed, (Satellite Name, TP and Channel Name)
| 2. You can navigate between channels with these buttons.
- A/V : Moves up/ down
- 4/P or @/@ : Moves page up / page down,
- RED( E): Displays all channels in current satellite.
- GREEN ( [E] ): Displays channels sorted by alphabetical order,
-YELLOW([ _]): Displays channels sorted by transponder.
- BLUE ( ): Displays channels sorted by FTA/ FTA + Scrambled/ CAS.
3. Yon the selection bar is positioned on the channel you want to see, press OK on the
remote.
Other Functions of the Remote Cc
> Volume Control
|. While you are watching a program me. press </P» buttons on the remote to control
volume.
2. Press the MUTE button to turn off the sound of the program me.
Press MUTE button again to turn the sound On.
» Channel Information
Display the information of a program by pressing the INFO button on the remote.
6. Delete TP: Press Yellow ([__])button on the remote to delete the selected transponder.
& Technomate
p TV/ SAT Switching
Changes the signal reception path to RF modulator.
- ТУ Моде: ТУ ANT INPUT signal will show.
- VCR Mode: VCR SCART INPUT signal will be shown.
-SAT Mode: Satellite signal will be out through RF,
» TV/ RADIO Switching
Switch TV channel to Radio channel or vice versa.
» RECALL
Return to the previous channel/menu.
> Audio
Press Audio buttons on the remote, then the subtitle and audio related menu
will be displayed.
- Audio Mode: Stereo — Mono-Left — Mono- Right.
- Audio Track: All tracks available in this program.
- Audio Level : Select between, High -> Medium -> Low
* Note: These subtitle and audio parameters are available only when the receiving channel supports these functions,
> Teletext
Teletext Service is a text data service from a service provider.
It is available only if the channel broadcasts this service.
> SUBTITLE
You can press select the subtitle language of current channel.
> SAT
Press the SAT button on the remote and select a satellite in the Satellite List.
» FAV
Press FAV button on the remote to display a favorite channel list in the favorite group.
[e] té E
E] MÍ
vs pes pen
RE a
mes"
Mr | —
——. a. A «а -
» Multi-Picture Display
Press the MOSAIC button on the remote to display
multi picture mode. You canselect the numbers of
multi pictures. e.g. 1x2, 2x2, 2x3, 3x3.
> COLOR Adjustment
Press the COLOR button on the remote to select Colour
Adjustment menu.
By using the </P buttons on the remote, you can adjust
the brightness, contrast and the colour of picture.
» FREEZE
You can press this key to freeze the video. Press it
again to resume the video.
—ar
& Technomate & Technomate
> ZOOM
You can press fo zoom in the video.
1. Press the PAUSE button and press ZOOM button
You can zoom in sections of Freezed Video.
2. While watching a program, press.
You can zoom in sections of playing video.
3. To cancel the freeze status,
please release the zoom status.
» SLEEP
You can set the receiver to turn off after a few minutes.
Press the SLEEP button fo set a Sleep timer.
- Wake Up Channel: You can set wake up channel by pressing the OK button on the remote.
- Sleep Mode: You can set the cycle of the sleep mode: Off/Once/Daily.
- Sleep Time: You can set asleep time by pressing any NUMERIC button.
- Automatic Stand by : Selects auto standby time (OFF/After 1-8Hour)
After making your selection press (sk) to confirm
- Timer Lead Time : Press (9%) to set the Timer Lead In And Lead Out Time.
A/V Output Setting
This sub-menu allows you to set the audio/video output setting.
- Audio Language: Default audio language of the channels.
- Subtitle Language: Default language of subtitle.
- Use Recall list : Store previous channels. If you press recall key
on RCU then you will show recall list.
- SCART : Select the SCART output.[CVBS/RGB)
- Screen Format : Select the screen format. (16:9 / 4:3)
-To cancel a Sleep Timer, press the SLEEP button until - Display Format : Select the TV aspect ratio
you set the time as "0 min". : (Letter Box/Pan Scan, Full Screen/Pillar Box)
(Disable, 10, 20, 30, 60, 100, 120 Minutes) - RF Type : Select among supported PAL standards.
» V.FORMAT (PAL B/G, PAL |, PAL D/K).
Press the V.FORMAT button to change - RF Channel : Set the RF channel to which to display
the video resolution : 1080p > 1080i > 720p > 576p > 576i the audio and video signals on your TV set (21 to 69); if you
Select 40, they will be displayed at channel 40 on your TV sel,
» WIDE - Video Format : Select the Scanning type (Interaced, Progressive)
Press the WIDE button to change the TV's Aspect Ratio : - Digital Audio : Select the Audio output type (DOLBY SPDIF/PCM/DOLBY HDMI)
- 43 : Pan-Scan or Letter-Box - Radio Backpicture : Set the radio backpicture to On/Off
- 16:9 : Full-Screen or Pillar-Box :
> SYSTEM SETTINGS LA
EN CO TEN NA a TN
me Setting _— OSD transparency, Information and volume timeout. a
This sub-menu allows you to set yourlocal time, - Menu Language: Select the desired language of the menu. yr
wake Up time, wake up channel and sleep time. - Transparency: Select OSD transparency of the menu. (1% ~ 100%)
“GMT Usage: If you turn it ON. local time is determined - Information Timeout: Select the display duration of the information ~~ ==
by adjusting the differences from GMT banner 1sec/ 2sec /3sec /5sec /10 sec. -
р"
(Greenwich Meantime}, according la - Volume Timeout: Select the display duration of the volume box ;
your location. 1 sec /2sec / 3 sec / 5sec / 10 sec. —
- Current Date: Ií GMT Usage is ON, this date is determined - Moving Display Message: Turn the DISEgC moving message ON/ OFF.
by GMT.If GMT Usage is OFF. you can modify Front Display Setting 5
this by pressing the OK button on the remote.
This sub-menu allows you to set the Standby Mode.
venue mma!
Current Cute “” wo ok j
Cien Thee .. = 3
.
1
|
a
If you set OFF, the receiver doesn'i refer fo
adjusting current date and current time.
- Current Time: If GMT Usage is ON, this time is determined by GMT.
IF GMT Usage is OFF, you can modify this by pressing any NUMERIC button.
- Local Offset: IF GMT Usage is ON, the Local time is GMT time + Local Offset.
- Standby Mode: Select the standby Mode.
(Normal / Power Saving)
- Use Recall list : Store previous channels. If you press
- Wake Up Mode: You can set the cycle of the wake up mode Off/Once/Dally. ;
2 y E à recall key on RCU then you will show recall list.
- Wake Up Time: You can set wake up time by pressing any NUMERIC button,
— ma —@
& Technomate
This sub-menu allows you to change the password option to access or lock menu
entry and to change password.
- Receiver Lock: If you turn it ON, you will be asked to
enter PIN code when power on.
- Remote/ Ch/ Install Lock: If you turn it ON, you will be
asked to enter PIN code when you go to Installation/
Edit Channels and When you use Function keys on
the remote.
- Lock Channel Confirm: If you turn it ON, you will be asked
to enter PIN code when you switch to a locked channel.
ET aay EU
- Age Limit: Prevents children or unauthorized people from
— р | watching the specific programs.
pmo de ~ [Free / 8 above / 12 above / 15 above / 18 above)
- Current Password: Enter current password to change
password,
- New Password: Enfer the new password you want fo
change.
A * Note : The default password is 0000.
Factory Reset DS
This sub-menu allows you to restore the factory setting
if the users encounters a problem after changing any
settings.
- Delete Radio Channels : Erase all radio channels.
- Delete Scramble Channels: Erase all scramble channels.
- Delete All Channels: Erase all channels and restore default setting. -
- Factory Reset : Erase all channels and restore factory
default setting.
- Save As Default Channel : Change the factory channels.
- Restore Default Channels : Restores 25 satellites and
approx 1,500 channels pre-tuned.
IP Setting E |
If the Network supports DHCP, IP settings can be allocated automatically.
If the Network does not support DHCP, the Addresses must enter manually (Stafic IP).
- DHCP Usage: On/Off to receive IP settings automatically
@-Technomate
- IP Address: Here enter the IP address
- Subnet Mask: Here enter Subnet Mask Number from your Network
- Gateway: Here enter IP address of Gateway (e.g. router)
- DNS: Here Enter IP address of main DNS Server
- Mac Address: Mac Address display
- Firmware update: Support download from a LAN.
1) BLUE button, appear input target IP address.
2) button to connect after input a target IP.
3) Choose a update software and (OK)button for downloading.
* Note : Have to run PC tool before connect PC.
Data Transfer —
This sub-menu allows you to transfer the software of
areceiverto anotherreceiver of the same model.
- Software: Transfer the firmware of a receiver to another receiver,
- Channel Data:
Transfer the channel data of a receiver to another receiver.
-All: Transfer all data (Firmware + Channel Data) to another
receiver.
> EDIT CHANNELS
E NN E <
This sub-menu allows you to set up favorite name and favorite lists.
You can choose TV or Radio channels by pressing
the TV/RADIO button. Support is for 16 favorite groups.
I. Press the MENU button on the remote to display
the main menu.
2.Use </> and 4/V button on the remote to
move in the menu.
3. Select Set Favorites, Select Favorite Group will
appear.
4. Select a favorite group by pressing the 4/Y
and OK buttons on the remote. The TV/ Radio
channel list will appear.
If you want to edit the favorite group name,
press the RED (fg) button on the remote. A
virtual keyboard will appear.
(Y
& Technomate
5. Set favorite channels by pressing the 4/Y
and OK buttons on the remote. The selected
channels will have a heart symbol to the right.
Press the OK button on the remote again
to remove the channel from a favorite group.
6. Press the EXIT button on the remote to return to
the previous menu.
Rename CH/ Edit PIDs BE
This sub-menu allows you fo rename the channels and input user PID.
You can switch between TV or Radio channels by préssing the
TV/RADIO button on the remote. :
|. Select Rename CH/ Edit Pids, the Rename CH/
Edit PIDs menu will appear.
2. Press the OK button on the channel that you
want to edit.
3. Press the OK button on Edit Name to rename a
channel. À virtual keyboard will appear.
Rename a channel by using the </P,4/Y, and
OK buttons on the remote. Press the EXIT button on
the remote to exit.
4. You can edit a PID by using NUMERIC buttons ds
ontheremote. HAC
Wie wm
*Note: The VIDEO PID, AUDIO PID and PCR PID are very important
for optimal satellite signal reception.
This sub-menu allows you to move a channel
in the list. You can switch between TV or Radio
channels by pressing the TV/RADIO button.
|. Press the OK button on Move Channels, the
Move Channels menu will appear.
2. Press the OK button to select the channel that
you want to move, then arrow buttons will appear.
@ Technomate
3. Use any NUMERIC buttons on the remote to move the selected channel or
press 4/Y, OK buttons to move a channel.
4, Press the EXIT button on the remote to return to the previous menu.
Lock Channels —
This sub-menu allows you to lock channels.
Once the channelis locked, every time you
want to watch the channel, you will have to
enter the password.
* Note: If you set Lock Channel Confirm OFF, you will not be
asked to enter a password even if a channel is locked.
|. Press the OK button on Lock Channels, the Lock Channels menu will appear.
2. Press the OK button to select the channel that you want to lock. A lock symbol
will appear next to the channel's name.
3. Press the OK button again to unlock a channel. The lock symbol will disappear.
4, Press the EXIT button on the remote to return to the previous menu.
Skip Channels В
This sub-menu allows you to skip channels.
Once a channel is skipped, every time you fry to change the channel using A/V
in the viewing mode, this channel will be skipped.
* Note: If you try to change the channel using NUMERIC buttons in viewing mode, you can watch this channel.
1. Press the OK button on Skip Channels, the
Skip Channels menu will appear.
2. Press the OK button on the remote to select
the channel that you want to skip. À skip symbol
will appear.
3. Press the OK button on the remote again to
cancel skip. The skip symbol will disappear.
4. Press the EXIT button on the remote to return to
the previous menu.
@ Technomate
This sub-menu allows you to delete channels.
* Note: If you delete a channel, you cannot watch this channel until you do a channel search again.
|. Press the OK button on Delete Channels, the
Delete Channels menu will appear.
2. Press the OK button to select the channel that
you want to delete. A symbol will appear.
3. Press the OK button again to cancel delete.
The delete symbol will disappear.
4. Press the INFO button to delete all channels in
the current list. You will be asked to enter a password.
5. Press the EXIT button and select yes to delete and return to the previous menu.
Add Channels ВЕ
1. Select the satellite and save in the Satellite setup before Add Channels.
- Satellite: Select a transponder which you want to search.
и — dm chnomab
pew воен! - Channel Name: Press OK button on the Channel Name
ue that you want to edit.
- Channel Type: Select TV/Radio.
- Video PID/Audio PID/PCR PID: Select and edit by using
numeric buttons 0-9 and ?/? Buttons on the remote.
- Video Type: Select video type MPEG 1/2 / H.264.
- Audio Type: Select audio type MPEG1/2 / HE-AAC
/ AC3 / MPEG4 / AAC / DD+.
2. Press Yellow ([___])buttons on the remote to add channel.
- Transponder: Display the Transponders of the selected satellite.
& Technomate
> EPG (ELECTRONIC PROGRAMME GUIDE)
EPG (Electronic Programme Guide) =
This sub-menu allows you to view the electronic programme guide (if available).
|, Press the EPG button on the remote, the EPG menu ———— |
will appear.
2.Press the </P to gotothe previous/next EPG.
3. Press the </> or @ /® buttons to change the
channel.
4. Press the OK button on right side of screen (Program
List) and the selected programme will be reserved pe amr —
in the Timer menu. Repeat for more programmes. =
5. Press the REC button on right side of screen(Program List) and the selected
program will be reserved(Record ON) in the Timer menu.
Repeat for more programs.
6. Press the TV/ Radio button on the remote to view TV/RADIO channel list.
7. Press the SAT/FAV button on the remote ti view the SAT/FAV list,
8. Press the RED (ag) )bufton on the remote, the Timer menu will appear.
7.Press the INFO [button on fhe remote to EPG mode switching.
Timer > :
This sub-menu allows you to set the on/off time of your receiver,
1. Press the RED (Ea button in the EPG menu,
the Timer menu will appear.
2. Press the A/¥ buttons fo move fo other menus.
' 1 4 | " | n 7 "
aie er mt == E | wef
> A
(vos OE a =I 3, Press the </» buttons to change the selection.
dre TT Dewees
о “. om zb |
Г ов, E riada ее —
- Timer No. 1-8: Select the timer that you want to modify.
a.
- State: Select the timer: Off/Once/Daily/Weekly.
- Date: Press the OK button to select the date. A virtual calendar will appear.
- Start Time: Enter the time by using the NUMERIC buttons on the remote for your receiver to turn On,
- End Time: Enter the time by using the NUMERIC buttons on the remote for your receiver to turn OFF.
- Channel: To view the channel list, press OK button on the remote.
- Record: To record program. (Off/On, This function is available when a USB device is connected)
- Power Off © Turn the receiver off when the timer finishes your receiver power-off.
—e
>
&@ Technomate & Technomate
GAMES
LE |
Li м 5. Press the RED ( a) )button to undo previous move.
_—— = x You can only undo a step once at a time.
ce e |. Press the OK button on Tetris, the game will
load. 6. Press the GREEN button to restart the game.
La 4 2. Select a skill by using the A/¥ buttons on the 7.Pressthe YELLOW ([__))/BLUE( EJ) buttons to
po. “ remote. jump to the previous/ next level.
Ma. You can jump between completed levels.
3. Press the OK button to start a game or press CTE CTE Tape
the EXIT button to return to the previous menu. 8. Press the EXIT button to quit a game.
sus Mu I в’ Ter
4, Press the OK button to rotate the block.
SE = енто wi 5. Press the </» button to move the block.
lar 6. Press the Y button to drop the block.
=, у. 1. Press the OK button on Snake, the game will
Po x 7. In the top right window, you can see the load. NC +
"a. next block.
2. You can select a skill using the A/¥ buttons pie я r
8. Press the EXIT button to quit a game. on the remote. Pr Mo /
| „у |
— — = 3. Press the OK button to start a game or press the Ng
EXIT button the remote to return to the previous |
menu. mel messes»
Sokoban & |
| : ыы 4, Press the 4/Y or 4/» buttons to move.
To play Sokoban, you have to push the balls into their correct positions. The balls can
only be pushed, not pulled. You have to be careful not to push them into a corner
where you cannot get them out again. You can only push one ball at a time.
5.1f the snake takes BLUE blocks on the screen.
the length will increase.
I. Press the OK button on Sokoban, the 6. If the snake takes RED blocks on the screen, +
Game will load. a... ima |
== the length will decrease.
а ” , r Te
2.5elect a skill by using the 4/Y buttons onthe E. Ay 7.1f the snake takes BLACK blocks, the game wil v Ny
remote. )
end. Е ааа ис
3. Press the OK button to start a game or press oe Ln | | =
the EXIT button to return to the previous menu. 8. Press the EXIT button to quit a game. — — L
"uy Seil! a tour
4. Press the 4/Y or </> buttons to move.
www.technomate.
& Technomate
- USB Menu (How to download SW from USB)
This sub-menu allows you to playback MP3 (music) and JPEG (picture) files and
fo download software and channel lists by connecting your USB memory stick
(USB flash drive) to the USB port on the receiver.
1. MP3 Menu
-Select the MP3 file you want to listen to by using the A/¥ & OK buttons in the file list.
- Press the EXIT button to hide the file list, You can then select an option using
4/» & OK buttons.
- Use the VOL+/VOL- buttons to adjust the volume.
- Press OK button on CSP. The MP3 file list will be displayed.
- Press OK button on (mag. The MP3 file information will be displayed.
* FILELIST : Open/Close the MP3 file list.
* INFO : Displays MP3 file information,
* YELLOW ({___) ) : Choose:Hard Disk or USB device.
2. JPG Menu e
- Use the 4/Y buttons on select a picture. |
- Press OK button to display the picture.
* EXIT : hides jpg file list
* RED( Pal) : Selects drive letter
* GREEN( al) : Slideshow
* YELLOW([__]): Set the time interval between the slides, (slideshow)
* BLUE( fa) : Rotate the picture.
3. Data transfer Menu (How to download SW from USB) /Download/Upload
- Select the software or channel list you want to
download by using the 4/V buttons in the list
- Press the OK button to start the software downloade
* YELLOW ([_]) : Choose-Hard Disk or USB device
* RED( aa) : Upload the current CNDF
(compressed dish and channel data file).
&@ Technomate
* Warning : Do not turn off your receiver whilst downloading.
4. Timer Manager
This sub-menu allows you to set the on/off time of your receiver.
Press the OK button to select the timer.
Press the </P buttons to change the selection.
- Timer No. 1-32 : Select the timer that you
wantto modify.
- State : Select the timer: Off/Once/Daily/ om iD
Weekly. в. TVR
- Date : Press the OK button to select the date. EE Reka mr
A virtual calendar will appear. ce ba VS
Use EPG / FAV to change month. UT a F— ФО
- Start Time : Enter the time by using the Де ado ms
NUMERIC buttons on the remote for your
receiver to turn on.
- End Time : Enter the time by using the
NUMERIC buttons on the remote for your
receiver to turn off,
- Channel : To view the channel list, press OK button on the remote.
- Record : To record program. (Off/On, This function is available when USB
device is connected)
5. Disk Manager
- Default Disk : Set the PVR disk.
- Disk Information : Choose the hard disk drive.
You can view the information of selected drive,
(File system, total size, used size, free size) cn ES
A U mara)
- Chek Disk : Choose the Hard Disk or USB device. = re ère
You can check the USB device.
res 47 166 Hytme
- Format Disk : You can format the USB vdevice.
Pur . -
* Note : The receiver supports FAT15 and
FAT32(Recommended) of USB device,
but NTFS file system is not supported.
If USB device is formatted by NTFS,
Please change file system to
FAT32(Recommended) by PC.
see www.technomate.com/support for details
- Testing USB Speed : You can test your USB device for supporting PYR functions.
- Timeshift Rec Time : You can change default timeshift recording time.
- Auto Timeshift : Set automatic timeshift On/Off.
-
—
-
I~
~
-
-—
be À
SS
оо
pu
я
os
-
=
--
=
-
®
-
-
с
„я
=
=
& Technomate
PVR Mode via External HDD or USB
File List —
P File Playback
1. Press the FILELIST button to open the file list, Select
the file you want to playback
by using UP/DOWN & OK buttons.
2. Press the OK button. On the left side of screen,
detailed information about the
selected file will be displayed. (Recorded Date/Time,
Used size, Total Size)
- For Full Screen, press the OK button once more
and then following time-bar will appear.
P Edit Menu
Enter the password. Press the YELLOW button.
A popup menu will appear.
Select the file that you want to edit, and
set its parameters as desired.
1. Normal Mode : Press the OK button on file that you
want to see a preview.
2. Lock Mode : Press the OK button on the file that
you want to lock/unlock.
3. Delete Mode : Press the OK button on the file that
you want to delete.
4. Rename Mode : Press the OK button on the file that
you want to rename.
- RED : Choose from : File Mode <-> Dir Mode
- GREEN : Displays all sorted files. Choose from :
Sort by name <-> Sort by time
* IF you sel "Channel Lock to OFF (refer to security
_ setting), you will not be asked to enter a password,
even if the channel is locked.
Trick Mode a"
You can operate the trick mode while you are playing the recording files.
These functions are available in playback mode, time-shift mode or recording mode
Powerfully,
a... MAI |
-—
a ВО ня re E“
» PLAYBACK ) La =
This button will display a time-banner. A FE а,
If you want to open the playlist while playing oa LCE RTT
v kE TC © 0.040 113s
the file. press the PLAY button on the remote. py nr : |
sa AY 11.300 a 01720 10)
In This Mode, press the INFO button to show LF FOI ETN BTR
the trick-operation. „а E PELO
> PAUSE r ————— -
This button will pause the file until you playback
again (press the PLAY button or PAUSE button to
resume watching).
g "ne — 9 (15.0
6. NO usar Lp ire
ns En JETT МСТ 5 ma
#8 Technomate
p ADVANCE
If Time-Shift mode is enabled, press the ADVANCE
7.350 « 1.200 158 button to go to the real time live broadcast.
1 er: TINO
1 ER UAT EE)
wad BS EN I ST RR A
SM Lui ALEA EE
——
ПИ Нл Я?
(UNO ee
> FF (Fast Forward)
When playing the file, press the FF button to forward
the program (adjust the playing speed).
- Choose from : x2, x4 and x8, x8 and x32
D RWD (Rewind)
When playing the file, press the RWD button to rewind
the program (adjust the playing speed).
- Choose from : x2, x4 and x8, x8 and x32
» Slow (1/2x, 1/4x)
NT ME: $). y, |. _— =
NT TET TINE When playing the file, press the SLOW button to slow
en RATE the speed of the playback (adjust the playing speed)
ENE... 0740 0034 1650
AE 139 - 105%
iia dd E
q Ea — 9 90,
A EA NOW MUA. ly
> Jump
- Go to a desired position of the file by using the
LEFT/RIGHT buttons.
- If you press this key continuously, you can go fo
the desired position faster.
> Bookmark
To create a bookmard/chapter at a specific
time/place of the file.
- RED : Press the RED button and a red triangle will
appear at that position.
If you want to delete the bookmarked position,
press the RED button once more and the red triangle
will disappear.
- GREEN : Press the GREEN button to go/jump to the
previous bookmark position.
Playback will start from this point.
- YELLOW : Press the YELLOW button to return to the
next bookmark position.
Playback will start from this point.
JE
* Note : The maximum number of bookmarks is 20 for each file.
> File Edit
- BLUE : Press this button and edit (copy, cut) the file.
Press 'OK???' button to select edit start position and
one more 'OK???' button to select
edit end position. Select cut or copy.
ша НЕСЛО
po
=
t
-
x
Rd
[3
~~
<
=
=
>
EN
bd
о
~
v
—
=
=
-
=
&@ Technomate &@ Technomate
Time Shift
Instant Recording |
|. To pause and resume live TV channel,
press the PASUSE button. The default time
for Time-Shift is 30 minutes.
1. You can record the current channel you are
watching instantly by using REC button.
If you then press the PLAY button, a time-banner
will be displayed.
2. To resume live TV channel, press the PLAY button.
“ 30500
AE dear 4
3. The trick-mode operations are available,
To retum to the live broadcast,
press the ADVANCE button.
2. Press the REC button once more. The following E
picture shows that you can select an item when
you record the current channel.
- Channel : Displays the current channel
- Name : Displays the current recording name
- Duration : You can change the duration of
arecording's time by using the LEFT/RIGHT button.
Current recorded time will appear.
termo ET
LT * 4 _00 38 (30.01) »
* Note] ; DO NOT REMOVE the USB device while
recording a program.
Record Stop В Press ((&2)) button to display divx file list.
Las Press ‘& button to play the selected file.
Cs)
1. Press the STOP button on the remote to stop
the recording then Record Stop will be displayed. Вата
а tue ff
AIO [TR TANT
Ш Jo TITY SRE
2. Select the recording file by OK / STOP button.
Ne you sue?
3. Press EXIT button then selected recording is stopped. SYSTEM INFORMATION
You can check your receiver's current
information, such as the receiver brite aero;
ACE 104
model name, software version, hardware dei ae
Timer Recording в : WEST Le
== version, manufacturing date, etc. EME EE ao :
, - : 5 ь : I SAL (RY (E У
This function is available when USB device is connected. You can choose a channel A ТО Ч
to record from the Program Guide menu by using the REC button. *Note: This Informática la necessary when you want to downlesd -
(Refer to Electric Program Guide, Timer) a new software or you need to repair the receiver. =
& Technomate
COMMON INTERFACE
To watch scrambled channels. you will need a Conditional Access Module (CAM)
and a Smart card which is specific to that CAM from the service provider (broadcaster).
* Note: Without a CAM and a smart card, you can watch only Free-to-Air programmes.
1. Insert a CAM into the CAM slot in the receiver
and a Smart card into the CAM.
2. The message: CAM Initializing will appear.
3. Once the message has disappeared, you can
select the channel to watch.
Status of the CAM
|. Go to Common Interface. Press OK on the CAM
to see further information of the CAM.
2. Proceed with further instructions displayed on
the screen, then you can check further details
depending on the CAM in use.
* Note: Further detailed information is not mentioned in this manual
since the information depends on the type of CAM being used.
* Warning: Do not turn off your receiver whilst downloading
* Warning : Turn off the receiver from rear connect Rs232 then turn
on the receiver avoiding this can damage RS232 port
* CONDITIONAL ACCESS SYSTEM
Card Initializing = В
To Enjoy CONAX CAS7 scrambled channels,
you will need a Smart Card from the service provider (program distributor).
If you are subscribing to services from more than one service provider, you will need
a Smart Card from each one.
Since a Smart Card is connected to a single service provider,
a limited range of channels will be available via it.
* Note : Without the Smart Card, you can watch only Free-To-Air programs.
E
@ Technomate
1. Insert the Smart Card into the receiver's slot designed for it.
2. The message ‘Smart Card Initializing’ will appear on
the screen.
3. After the message ‘Smart Card Initializing’ has disappeared,
you will be able to watch the channels offered by the service
provider.
The Status of the Smart Card ——
1. You can access detailed information about the Smart Card
using the / keys in the Main Menu to select 'CA' and
pressing A/V.
2. Proceed with further instructions displayed on the screen
to check more detailed information depending on the Smart
Card in use.
* Note : Futher detailed information is not mentioned in this
manual since the information depends on the Smart Card in use.
7," HOWTO DOWNLOAD SOFTWARE FROM PC TO RECEIVER
1,Connect the null model cable to the RS-232C conn-
IETS —— |
ection on the back of the receiver and to your PC
: Е) Tecimomato 5000 Series Downloader
2. Download the latest version of the TM Loader from
the Technomate web site (www.technomate.com) 200 E - |
and then unzip. FREE [e
3. Download the latest software (.STB) for yourreceiver | Zhen]
Ensure that the model number of the software is the ra anon ||
same as the receiver you have and then unzip. —_—
4, Click on Browse in the TM Loader. x
5.Select the file from where you saved it when you os
downloaded it from the Technomate website. 8 rechnoma 5000 Senes Downloader
6. Turn ON the satellite receiver.
7.Click on Connect on TM Loader and then click
Start to begin the software download
8. The downloading status is displayed.
9. Once it displays 100% Finished (wait until it has
completed erasing), the software download has
finished.
@ Technomate
Li ——- -.
10. When it completes the writing of the new software, (PB Tochnomato 5000 Soriss Downloader
disconnect the cable between the receiver and the PC.
A Factory Reset is required. 5
TO
11.Goto System Information on the main menu and ===]
make sure that you have correct software version. E
orto amie | oe |
ren Modem Cable Diagram>—
— Rs$-232C Cable
BB rechnomato 5000 Senas Downloader
эн!
a =} meme | Cove |
| НЕО OdOWNIDEN Als
If you want to download/ upload Channels, Click on Channels in the TM loader,
then select Download/ Upload
* Downloading Channels PC to TM-5000 Series
1. Click on Download, and then Click on Browse in the TM Loader.
2.Select the file from where you savedit.
3. Turn on the satellite receiver.
4. Click on Connectin the TM Loader and then click on Start to begin downloading
Channels PC to TM-5000 Series.
5. Once it displays 100% finished, the Channel downloading has finished.
* Uploading Channels TM-5000 Series to PC
1. Click on Upload, and then Click on Browse in the TM Loader.
2,Selectihe file and folder where you want to save in your PC.
3. Turn on the satellite receiver.
4. Click on Connect in the TM Loader and then click on Start to begin uploading
Channels TM-5000 Series to PC.
5. Onceit displays 100% finished, the Channel uploading has finished..
*You can upload/ download default channels maximum 1,500 TV & Radio channels.
If you want to add more than 1500 channels, you will have to da a channel search/scan.
Z Technomate
MO rn Ii | IA ~ epi Af") mr \ чт CAT par |) ое
HOWTO DOWNLC AU! AUF WAKE: 45) USE TO) Eee
1. Connect the USB HDD or USB device to the USB port
in the receiver.
2. Press the MENU button on the remote to enter the Data
Transfer menu.
3. In the main menu, press OK button on Data Transfer
in the USB menu.
4. Select the software or channel list you want to download
by using the 4/Y buttons in list, then download window wil
be displayed.
5. Press OK button to start the software download.
6. Press Red (fl) button on the remote to select the drive. ex) C:/, D:/, E:/, F:/
7. Press Yellow ([__)) button on the remote to upload the current channel list to
the USB HDD or USB device.
* Warning: Do not turn off your receiver whilst downloading
—#
& Technomate
below.
LED on front panel
does not turn ON
YI TROUBLE SHOOTING
There may be various reasons for the abnormal operation of a set-top box. If it
does not work properly, check il according to the procedures shown in the table
[Problem | Possible Causes
Suggested Remedy
A/C power cord
disconnected.
Connect power cord properly into
the power socket.
No picture or sound
Wrong connection of the
video/audio output fo TV
input terminal,
Wrong connection of
satellite dish/antenna
cable.
Satellite dish/natenna is
aimed a the wrong
direction.
No signal or weak signal,
Wrong setting of channel
information In MENU screen.
Connect power cord properly Into
the power socket.
Connect the dish/antenna cable
correctiy.
Check the cable connections, LNB
and other equipment connected
between the LNB and the receiver of
adjust the dish/antenna,
As above, Type the setting value correctly.
Black-and-white
screen or V-Hold
Your TV mode Is different
from satellite broadcasting
mode.
Use TV of the same mode.
Use the NITSC/PAL converter
connected to a receiver and a TV.
Remote
controller does not
work
Battery exhausted.
Fluorescent light interfering
with the remote controller.
Remote controller
Is Incorrectly aimed.
Remote type is not
properly selected.
Change the batteries.
Switch off the light.
Alm the remote control at the receiver.
Go fo password and press 0000
then go to the bottom of page and
change the remote type to type 1
ortype 2.
- The receiver is on but | cannot get any Menu on the screen?
How can | find out what software version | have?
@-Technomate
1) Checkif the scart or the RF lead is connected,
2) Check the A/V settings on your television is correct,
3) Scart cable or RF cable could be faulty therefore replace if in doubt,
How do | tune the RF output of the receiver to my television?
Yourreceiver's RF output has been Defaulted to PAL | and channel
frequency 40, Apply the tuning setup application of your television.
| get the message 'no signal’ displayed?
1)Checkif the LNB cable is inserted into the IF INPUT.
2)Check if the LNB setup menu is correctly set.
3) Your satellite Dish may be out of alignment or your LNB may be faulty.
4)Go to Easy intallatin guide and start fresh,
5) contact your dealer / installer.
| cannot access a particular channel | require?
You need to check the following :
1)Checkif you have the correct transponder.
Go to advance search , Turn on the Network Search,
press red button to tune.
2)Make sure you have correct PID numbers.
b) if above dose not help go to
www.lyngsat.com
www.kingofsat.net/en/prefs.php
Please contact your Supplier for further assistance.
Press Menu on the remote.Go to sytem information press ok,
Full information is displayed
| have lost my personal Lock Code setting, what do | do?
For security reasons, please contact your dealer,
@ Technomate
SPECIFICATIONS
INB/Tunerinpul
Demodulator
System resource
Video decoder
DVB
MPEG Audio MPEG 1 layer I/II,
MPEG 2 layer ||,
Remote control
Power supply
Rear panel
connectors
HDMI
LAN
RF modulalor PAL Connector
G/1/K TV Type channel number
Physical ad
..
5
Lo
A
_
=
x
11
Joint Stereo
Audio out
/ Video | Audio out
1
IEC169-2
IEC) 69-2
RJ-45
IEC 169-
—
x 54
1.8
Disposal of Old Electrical & Electronic Equipment{Applicable in the Evropeon Union ond other
Evropean Countries with separate collection systems)
This symbol on the product ar an its packaging Indicatas that (his product shall net be treated os
household waste. Instead It shall be handed over lo the applicable collection point for the
recycling of electrical and electronic equipnent, By ensuring this product is disposed of correctly,
you will help prevent potential negative conséauences for the environmen! anda human health,
which could otherwise be caused by inappropirate waste handling of Ihis product. The recycling
of materials will help to conserve natural resources.
For more delalled information about recycling of His product. please contact your local city
office. vour household waste disposal service or lhe shop whare you nurchased tha nroduct
=
—
~~
-
A)
E
~~
had
>
=
E
=
-
-
=
=
—
-~
-
~
..
=
>
ZZ Technomate
Z Technomate
Your Digital Partner for Life
»
YO) INTRODUCTION | a8
User's Manual EL) CONSIGNES ELEMENTAIRES DE SECURITE 48
TM-5402HD Cl+ Super + BAA a :
E) (CONTRÔLES/FUNCTIONS 50
ic -——
же Es | № OPERATION 54
)1010101010101010101010 emma <= = 3
010101010101010107 0 d Ч a
[o à | EE o ерЕса 21 EN CAS DE PROBLEME 65
“Technomate
CIDOLOY Sm ll!
ЗЕЕ ета CH
pelle Ema]
DIGITAL
-á и
E TALLIN os ‘7
[ | TT ares я SL PLE ah a X J
E
ou
~
—
.*
~
—
-.
A
~
ve
=
Pong
>
=
~
о
~~
ES
*
-
>.
-
P=
>
р
i& Technomate
97) INTRODUCTION
Nous vous remercions de nous avoir fait confiance pour l'acquisition de votre
Terminal Numérique. Nous espérons qu'il vous donnera entière satisfaction durant
de nombreuses années.
Ce produit étant un appareil de haute technologie, il est nécessaire d'en prendre
soin et de respecter |es consignes élémentaires de sécurité que nous vous
communiquons ci-dessous.
5 CONSIGNES ELEMENTAIRES DE SECURITE
Y Avant de commencer toute opération, bien lire le manuel.
v Ne pas toucher le câble d'alimentation avec les mains humides, il pourrait causer
un choc électrique.
v Ne jamais ouvrir le récepteur. Ne pas toucher l'intérieur du récepteur, ceci peut
causer un choc électrique.
v Laisser libres tous les orifices de ventilation du récepteur.
Vv Ne surchargez pas une prise murale, un cordon prolongateur ou un adaptateur
car cela pourrait entraîner un incendie ou un choc électrique.
V L'installation par un personnel qualifié est recommandée. Si la réception est
interrompue, contactez votre centre de service local.
V Installez le récepteur horizontalement. Une installation non conforme peut
endommacer le système.
v Ne pas déposer un objet lourd comme une télévision sur le récepteur.
Cela peut endommager le récepteur.
V Le récepteur ne doit pas être exposé à des gouttes ou à des éclaboussures.
V Aucun objet contenant du liquide, comme une vase, ne doit être placé sur
I'appareil.
& Technomate
Y Ne pas installez le récepteur :
* А Un endroit sujet à des vibrations.
» A la lumière du soleil directe,
» A l'humidité.
» A Une température trop haute ou trop basse.
» ou il ny a aucune ventilation.
v Déplacer le récepteur d'un endroit chaud à un endroit froid provoquera de la
condensation. N'allumez pas le récepteur durant une ou deux heures, jusqu'à
qu'il soit complètement sec.
227% POINTS DE CONTRÔLE AVANT L'EMPLOI
® Accessoires
» Manuel d'utilisation
» Télécommande
» Piles (type AAA)
Si certains accessoires énumérés ci-dessus sont perdus, entrez en contact avec
votre représentant afin d'en obtenir de nouveaux.
® Antenne parabolique
Votre antenne devrait être installée et orientée correctement et l'élévation doit
être ajustée avec précision.
Ce récepteur est conçu pour être compatible avec DISEaC 1.2.
Demandez à votre revendeur pour plus d'informations.
—49
& Technomate & Technomate
BN ю
%” CONTROLES/FUNCTIONS © Panneau Arrière
® Panneau Frontal
| #400940 008908
9400890400040
SPOF O veran
as
65.
VAT
oe 00 сто НЙ,
+0090 109409 |
Ells EE JC = A A
LANA USE HDMI > =) AE I san осо |
A ——l" ——
= Technomate &) €) © o © © 7 a)
mooy HDMI
A eros Ma TM-5402HD Cl+ я
e No, Name Connector Function |
] LNB INPUT IEC 169-24 female
| 2 LOOP OUT IEC 169-24 female
€) e) 4 €) 3 VIDEO RCA cinch Sorite vidéo composite
4 AUDIO L RCA cinch Sortie audio L
1. Mise en veille / Mode fonctionnement 5 AUDIOR RCA cinch Sorfie audio R
Voyant rouge = mode veille 6 Y RCA cinch
Pas de voyant = mode fonctionnement. 7 Pb RCA cinch
2. Témoin de la télécommande = infrarouge 8 Pr RCA cinch
; ; 9 VCR/AUX SCART
3. Mise en veille SCART
Appuyez sur ce bouton pour alterner entre les modes fonctionnement et veille. 10 IV SCART SCART Sortie CVBS. RGB Sortie audio
4 CH. (A/V)
Permet de naviguer dans les services vers le haut et vers le bas. I RS-232C DB-7
12 RF OUT UHF 21-69 IEC 169-2 MALE Sortie antenne terrestre a
raccorder au téléviseur
13 TV ANTIN IEC 169-2 female Entrée d'antenne terrestre
14 S/PDIF Fiber Optic Sortie audio digitale
15 USB USB Receptacle A-Type USB Interface
16 LAN RJ-45 10/100Mbps Ethemet
17 HDMI HDMI Digital Video/Audio Output
—{51)
& Technomate
® Télécommande ® Télécommande
© © ©
я = A
1. POWER: To turn the receiver On/Off
2. MUTE: To turn the sou
20. PLAY: Play Content.
21. PAUSE: Pause playback.
3. TV/RADIO: 1 22. REC: Start recording.
to len between TY sng Radio O 23. FILELIST: To display the filelist.
4. TV/SAT: To switch between the 24. STOP: Stop Playback.
satellite input and UHF/VHF :
25. RWD: Rewind a file.
antenna input
26. FWD: Forward a file.
27, SLOW: Playback in slow mode.
28. ADVANCE: Go to live channel.
29. Color Key: To use special functions
of
0
ha
©
Of
©
A
o:
©
®
©!
©!
©:
00
ое:
O:
@:0:
5. EDIT: To go to Edit Channels Menu.
de
т,
6. SLEEP: To tum the unit off after a preset
time.
ED ES ED 7. MOSAIC: To display multiple pictures. in the menu.
| a 30. EPG: To show the TV/Radio program
2B ID
EZ E E | 8. FREEZE: Press once to pause live TV. guide.
Ea TB в TEE 31. FAV: To show favorite list in the favorite
> >>
rein Y 9. ZOOM: Activates the zoom function. group or to move to the next page.
© M 32. TEXT: To show the teletext contents if
=
=F
10. UHF: To adjust UHF channe teletext is transmitted. Used for
eceee cc
EC EOGEGC[COE
E ;
11. Numeric Keys (0 - 9): To enter
numerical settings(such as channel
numbers) directly.
12. USB: To show the usb menu.
13. RECALL To go to the previous
channel menu. Used for special
functions in menu mode.
14. MENU: To enter or exit the main menu.
15. EXIT: To exit from the present menu
and to go to the previous menu.
curent program. Press twice to show
detailed information.
19. SAT: To show Satellite list.
>
-
seee
EEE
7 special functions in menu mode.
33. A-Z: To sort channel list.
7 34. AUDIO: To show Multi-language audio
track, the stereo-mono mode and
1
E subtitle information. Used for special
functions in menu mode.
&) 35. SUBTITLE: To show the subtitle contents
if subtitle is transmitted.
"e
— 36. Color: To control brightness, contrast
&) color of a picture (when in CVBS mode).
37. POS: To show the DISEgC motor view
e control.
38. BOOKMARK: Set the bookmark position.
&
ao 16. UP & DOWN: To change channels in E - EE A 5
св o non-menu mode and move the cursor $ 7 Technomate. E) 39. V.FORMAT: To change video output's
y up / down in menu mode. E | TM-S000HD Series [| resolution.
EITechnomate 17. LEFT & RIGHT: To change the volume 5 | If ‚ №7 40. Wide: ie said Ei ere da
TM-5000 HD Seri level in non-menu mode. A $ (Full screen or Pillar box(] 6:9) 4
18. INFO: To show information about the E :
41. IP: To go to Set IP Menu.
42. F2: To display the Divx filelist
43. F3-F5: Reserved button for new
function.
es
р
-—
<
SQ
-
=
-.
=
a
bad
=
po
a
=
v
A
с
=
>
Ed
& Technomate
Ne am
44 EQUIPMENT CONNEXION
— — —— — - - — — —— — — —— — — — — —— ——
® Raccordement avec le système A/V/ antenne / TV set
|. Raccordez TV ant IN de l'appareil à l'antenne TV.
2, Raccordez RF out de l'appareil au RF-IN de la TV.
3. Raccordez vidéo et Audio de l'appareil au TV et Vidéo de la TV.
Raccordez le connecteur rouge et blanc à audio R et audio L, et le jaune dans
le port vidéo respectivement.
4, Raccordez votre antenne satellite.
| OPERATION
+
© Démarrage
Démarrez le récepteur en appuyant sur Power et procédez à l'installation du
système comme suit :
Installation du menu lang
1. Allumez votre récepteur et TV,
2. Le menu langage apparaitra.
Sélectionnez la langue et appuyez sur la touche OK de la télécommande
pour proceder.
———
Installation Satellite =
1. Appuyez sur la touche menu de la télécommande pour faire apparaître le menu
2. Utilisez les touches 4/» el 4/Y de lo télécommande pour se déplacer dans le
menu.
3. Sélectionnez Satellite Setup = installation satellite, alors le menu installation satellite
s'affichera à l'écran.
& Technomate
линии
Installation Satellite =—
st
4, Sélectionnez chaque menu que vous voulez éditer / changer.
Satellite : sélectionnez le satellite souhaité à l'aide des touches 4/» de la
télécommande.
« Degré de l'antenne:
« LNB Power : A l'aide des touches sélectionnez sur ON/OFF/13V/18V.
« LNB Type : Sélectionnez votre type de LNB sur soit Single/Universal/OCS.
« Fréquence LNB :
« 22KHz : Sélectionnez sur ON/OFF ou 0/22 KHz.
« Diseac:
5. Scan : appuyez sur la touche rouge de lo télécommande pour commencer les
recherches satellite.
6, Rename= renommer : Appuyez sur |a touche verte de la télécommande pour
renommer le satellite sélectionné.
7, Save= sauvegarder : Appuyez sur la touche jaune de lo télécommande pour
sauvegarder.
8, Delete= supprimer ; Appuyez sur la touche bleue de la télécommande pour
supprimer le satellite sélectionné.
Installation motorisée
Appuyez sur la touche MENU de la télécommande pour afficher le menu principal
]. Appuyez sur la touche MENU de la télécommande pour afficher le menu principal
2. Utilisez les touches 4/» et A/Y de la télécommande pour déplacer dans le menu.
3. Sélectionnez installation motorisée, la fenêtre suivante apparaîtra.
4. Sélectionnez chaque menu que vous voulez éditer ou changer.
Satellite : Sélectionnez le satellite souhaité à l'aide des touches 4/» de la
télécommande.
« Transpondeur : Montre la valeur courante de transpondeur du satellite choisi,
DISEqC Motor : À l'aide des touches, sélectionnez OFF 1.2 USALS.
- Sauvegarder : appuyez sur la touche OK de la télécommande pour sauvegarder.
5. Appuyez sur la touche rouge de la télécommande pour commencer les recherches.
6. Appuyez sur la touche verte de la télécommande pour renommer les satellites.
—{s5
& Technomate
1. Appuyez sur la touche menu pour faire
apparaitre le menu principal.
2. Utilisez les touches </b et 4/Y pour
sélectionnez dans le menu.
3. Sélectionnez recherche avancée,
ensuite la fenêtre suivante apparaîtra.
4. Sélectionnez chaque menu que vous
voulez éditer ou changer.
« Satellite : A |'aide des touches «< /» de la télécommande sélectionnez le
satellite souhaité.
* Transpondeur : Montre la liste courante de transpondeur du satellite choisi.
+ Symbole rate : Montre la liste courante de symbole rate du satellite choisi.
« Polarisation : Sélectionnez Horizontal ou Verticale
« Type de recherche : Sélectionnez toutes les chaines ou seulement FTA ou
seulement TV
» Recherche Network : Sélectionnez Network recherche sur ON ou OFF.
5. Scan : Appuyez sur la touche rouge de la télécommande pour commencer les
recherches satellite.
6. Add TP : Appuyez sur la touche « verte » de la télécommande pour ajouter un
nouveau transpondeur à l'aide des touches numériques 0-9 et les
touches 4/» de la télécommande.
7. Delete TP : Appuyez sur la touche jaune de la télécommande pour supprimer le
transpondeur,
& Technomate
Recherche PID р I
1. Appuyez sur la touche MENU de la
télécommande pour afficher le menu
principal.
2. Utilisez les touches de la télécommande
pour déplacer dans le menu.
3. Sélectionnez PID recherche. ensuite la
fenêtre suivante apparaîtra.
« Satellite : sélectionnez un transpondeur dans lequel vous souhaitez faire des
recherches.
« Transpondeur : il montre le transpondeur d'un satellite sélectionné.
* Symbol Rate : il montre la liste courante de symbole rate du satellite choisi
- Polarisation : sélectionnez Vertical ou Horizontal.
- Video PID / Audio PID / PCR PID : sélectionnez et éditez à l'aide des touches
numériques 0-9 de la télécommande.
« Add TP : appuyez sur la touche verte de la télécommande pour éditer le
transpondeur à l'aide des touches numériques 0-9 et des touches
4/b de la télécommande.
* Delete TP : appuyez sur la touche jaune de la télécommande pour supprimer le
transpondeur sélectionné.
& Technomate @ Technomate
Sélection de programme =
Vous pouvez changer le programme courant par un autre programme.
p Controle du volume
» Dans le cas où vous voulez sélectionnez
une chaîne au hasard sans savoir le
nom de celle-ci, vous pouvez naviguer
entre les chaînes jusqu'à ce que vous
trouviez ce que vous souhaitez.
|. Lorsque vous regardez un programme, à l'aide des touches 4/> vous
pouvez contrôler le volume.
2. Lorsque c'est nécessaire, appuyez sur la touche Mute pour couper le son.
Appuyez à nouveau sur la touche mute pour remettre le son.
» Si vous connaissez le numéro de chaîne
souhaitée, entrez le numéro et
attendez 2 secondes jusqu'à ce que la
chaîne change.
>» Information
L'information à propos d'un programme apparaîtra en utilisant la touche INFO
de la télécommande.
b Si vous connaissez le nom de la chaîne
souhaitée, appuyez sur OK et la liste de chaîne apparaîtra.
|. Dans l'écran droit, l'information détaillée de la chaîne sélectionnée apparaîtra.
2. Vous pouvez naviguer entre les chaînes avec ces touches:
» A/V : Déplacer vers le haut et vers le bas
- 4/p : Déplacer de page en page
* Rouge : Affichera toutes les chaînes
Vert : Affichera toutes les sortes de chaînes par ordre alphabétique
» Jaune : Affichera toutes les chaînes par franspondeur
+ Bleu : Affichera
3. Lorsque la chaine souhaitée est sur surbrillance, appuyez sur OK pour confirmer,
& Technomate
® EDIT CHANNELS
Installation des chaines favorites —
Ce sous-menu vous permet d'installer le nom préféré et les listes préférées comme
vous le souhaitez.
En utilisant la touche TV/Radio, vous pouvez alterner entre les modes TV et Radio.
Il soutient 16 groupes favoris.
1. Appuyez sur la touche OK de pour
installation favorite, ensuite « select
Favorite Group » = « sélection de groupe
favoris » apparaîtra.
2. Sélectionnez un groupe favoris en
utilisant les touches 4/» et OK de lo
télécommande, la liste de chaînes TV
Radio apparaîtra, Si vous voulez changer
le nom du groupe favoris, appuyez sur la
touche Rouge et le tableau s'affichera.
3, Réglez les chaînes préférées en utilisant les touches 4/p et OK de la télécommande.
Appuyez à nouveau sur |a touche Ok de la télécommande pour enlever le groupe
favoris.
4, Appuyez sur la touche Exit de la télécommande pour retourner au menu principal.
Z Technomate
COMETE
Ce sous-menu vous permet de renommer les chaînes et entrer l'utilisateur РО.
En utilisant la touche TV/Radio, vous pouvez alterner entre les modes Tv / Radio.
Vous pouvez changer la liste de chaîne en utilisant les touches SAT/FAV de la
télécommande.
1. Appuyez sur la touche OK pour renommer
Ch / Edit Pids, le menu suivant apparaîtra.
2. Appuyez sur la touche Ok pour la chaîne
que vous voulez éditer.
3. Appuyez sur la touche OK pour renommer
une chaîne, le tableau suivant s'affichera.
Renommer une chaîne en utilisant les
touches A/Y et 4/p, OK de la
télécommande. Appuyez sur la touche Exit
de la télécommande pour quitter.
4. Vous pouvez éditer en utilisant les touches numériques de télécommande.
Déplacer les chaînes
Vous pouvez changer la liste de chaînes en utilisant |a touche GROUP
|. appuyez sur Ok pour déplacer les chaînes.
Le menu suivant apparaîtra.
2. appuyez sur Ok pour sélectionnez la chaîne
que vous voulez changer.
3. Appuyez sur les touches numériques pour
№. déplacer la chaine sélectionnée ou
appuyez sur les touches & / №, ОК роиг
déplacer une chaine.
4. Appuyez sur la touche Exit de la télécommande pour retourner au menu précédent.
Gi
& Technomate & Technomate
|
Ce sous-menu vous permet de verrouiller les chaínes. Une fois que la chaîne est Ce sous-menu vous permet de supprimer les chaínes. En utilisant les touches TV/Radio,
verrouillée, lorsque vous essayez de la regarder ; vous devez entrer le mot de passe. vous pouvez alterner entre les modes TV/Radio.
En utilisant les touches TV/Radio vous pouvez alterner entre les modes TV ou Radio. Vous pouvez changer le groupe de liste de chaine a I'aide de la touche GROUP.
En utilisant les touches SAT/FAV vous pouvez changer la liste de chaine. & Node : Attention ! St vous repérémer vue chaîne, vous ne pourrez la regarder que à vois Ia
* Note : si vous placez sur OFF la chaîne qui est verrouillée, alors vous ne devez plus entrer le recherchez à nouveau.
mot de passe même si une chaîne est verrouillée.
1. Appuyez sur OK pour « Suppression de
1. Appuyez sur la touche OK pour la chaîne chaîne ». Le menu suivant s'affichera.
verrouillée. Le menu suivant apparaîtra.
2. Appuyez sur la touche OK pour
sélectionner la chaîne que vous souhaitez
supprimer. L'icône « suppression » s'affichera.
2. Appuyez sur la touche Ok pour
sélectionner la chaîne que vous voulez
verrouiller.
L'icóne « verrouillé » s'affichera.
rar | re
x у wt bv тая Pe
21 Ram na |“
Da e
y "le ka _
) y.
3. Appuyez à nouveau sur la touche OK pour
confirmer.
L'icône « suppression » disparaîtra.
3. Appuyez à nouveau sur la touche OK
pour déverrouiller une chaîne, L'icône
« verrouillé » disparaîtra. 4. Appuyez sur la touche INFO pour supprimer toutes les chaînes de la liste courante.
Vous serez invité à entrerle mot de passe.
4. Appuyez sur la touche Exit = quitter de la télécommande pour revenir au menu
précédent. 5. Appuyez sur la touche Exit = Quitter pour revenir au menu précédent.
& Technomate
® EPG (Electronic Program Guide)
EPG (le guide électronique des prog
Ce sous-menu vous permet de visualiser le guide électronique des programmes
si il est disponible.
|. Appuyez sur la touche EPG de la
télécommande, le menu Guide
Eléctronique des programmes s'affichera.
2. Appuyez sur 4/» pour voir le guide
électronique des programmes précédent
ou suivant.
3. Appuyez sur les touches 4/> ou »M/ «
pour vous faire passer verticalement
d'une chaîne à l'autre.
4. Appuyez sur la touche Ok sur côté droit de l'écran (liste de programme) et le
programme sélectionné sera réservé dans le menu Timer. Vous pouvez sélectionner
autant de programmes que vous souhaitez.
5. Sélectionnez Programme TV/Radio à l'aide des touches TV/Radio de la
télécommande.
6. Sélectionnez SAT, liste Favori à l'aide des touches SAT, FAV de la télécommande.
7. Appuyez sur la touche Rouge de la télécommande, le menu Timer s'affichera.
ETT tira F r=
Ce sous-menu vous permet de programmer la mise en veille de votre récepteur.
1. Appuyez sur la touche rouge dans le menu guide, le menu Timer s'affichera.
2. Appuyez sur les touches </» pour déplacer á d'autre menu.
3. Appuyez sur les touches 4 /» pour changer la sélection.
= me
@ Technomate
® Interface commune
CAM (modules d'accés conditionne
Pour regarder les chaînes cryptées, vous avez besoin de modules d'accès
conditionnel (CAM) et/ou une carte à puce d'abonnement.
* Note : sans le module d'accès conditionnel et/ou la carte à puce, vous ne pouvez regarder
que les services libre d'accès.
1. Insérez le module d'accès conditionnel dans l'une de fente du récepteur et
une carte Smart dans le module.
2. Le message de « CAM Initializing » s'affichera à l'écran.
3. Après ce message, vous pouvez sélectionner la chaîne souhaitée.
Yl ENCASDEPROBLEME |
Y
pates, = a — и M
SOLUTION |
| a La — ————
Pas d'affichange sur le Vérifiez que le cáble d'alimentation. Branchez le cáble
panneau avant d'alimentation correctement.
Aucune image Vérifiez que le port de sortie vidéo est correctement
Aucun son branché à la TV.
Vérifiez la position du parabole.
Vérifiez la connexion du parabole.
Vérifiez le signal (aucun signal ou mauvais signal).
La télécommande ne Vérifiez et remplacez les batteries.
fonctionne plus
— {65
“Technomate
mioouwy HOImI
DIG TAL PLUS mr tai ad AA TM-5402HD Cl +
TM-5200 D USB Super® ra TM-5402HD CI+ Super
TM-5300 D+ USB Super® » FTA with Smart Card Reader
TM-5600 CIUSB Super? » | Common Interface
TM-5400 C1+ USB Super+ » 1 Common Interface with Smart Card Reader
& Technomate : копент НИ # Technomate x a al
e A Пера Ра В - 7299 E =3 Ey еси» ВЕ / `` TV-5300 HD COMAD Sreper т
RTE йе] | (I LR ACE
TM-6800HD Super+ USB PVR Ready TM-6900HD COMBO Super*+ USB PVR Ready
2 Technomate Z& Technomate
Your Digital Partner for Life Your Digital Partner for Life
@ Technomate
Digital Satellite Receiver Your Digital Partner for Life
User's Manual
TM-5402HD Cl+ Super +
a —
“Technomate
Z& Technomate
Dalia Fey
Your Digital Partner for Life y во с Е MSAD OF
| upper de
Technomate Ltd Tel: +44 (0)20 8884 0701
Unit 11 NobelRoad Fay:444(0)20 88840275
Edmonton
London www.technomate.com
N18 3BH [email protected]
United Kingdom [email protected] od
pelaje] E: | aa
apt dpi opa A TNA ie
">