Instruction Manual Popcorn Topping Dispenser

Instruction Manual Popcorn Topping Dispenser
Instruction Manual
Popcorn Topping Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Pedestal Assembly for
Models without Remote.
Rack Assembly shown for
Single Pedestal Models.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
© 2017 Gold Medal Products Co.
Part No. 39140
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
SAFETY PRECAUTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
WARNING
ALWAYS wear safety glasses when servicing this equipment.
010_010914
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
WARNING
Read and understand operator’s manual and all other safety instructions
before using this equipment. To order copies of the operator’s manual go to
gmpopcorn.com or write to Gold Medal Products Co., 10700 Medallion Drive,
Cincinnati, OH 45241 USA 1-(800)-543-0862
022_060215
Page 2
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
SAFETY PRECAUTIONS (continued)
WARNING
DO NOT allow direct contact of this equipment by the public when used in
food service locations. Only personnel trained and experienced in the
equipment operation may operate this equipment.
Carefully read all instructions before operation.
012_010914
WARNING
This machine is NOT to be operated by minors.
007_010914
Note: Improvements are always being made to Gold Medal’s equipment. This information
may not be the latest available for your purposes. It is critical that you call Gold Medal’s
Technical Service Department at 1-800-543-0862 for any questions about your
machine operations, replacement parts, or any service questions. (Gold Medal
Products Co. does not assume any liability for injury due to careless handling and/or
reckless operation of this equipment.) General images may be used in manual for
reference only.
Page 3
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
INSTALLATION INSTRUCTIONS
Inspection of Shipment
After unpacking, check thoroughly for any damage which may have occurred in transit. Claims
should be filed immediately with the transportation company. The warranty does not cover
damage that occurs in transit, or damage caused by abuse, or consequential damage due to the
operation of this machine, since it is beyond our control (reference warranty in back of manual).
Manual
Read and understand the operator’s manual and all other safety instructions before using this
equipment. To order copies of the operator’s manual go to gmpopcorn.com or write to Gold
Medal Products Co., 10700 Medallion Drive, Cincinnati, OH 45241 USA 1-(800)-543-0862.
Model Description
Model Series 2396 is a pedestal style topping dispenser with an LED lighted sign. Model includes
an open rack assembly which will accept 2 boxes of topping. The pedestal(s) mounts to a counter
top; the open rack is installed under the counter in an enclosed area for the heater to maintain
product temperature (countertop and cabinet to be provided by customer). The forced air
heating system controls the temperature of the cabinet to 120-130°F. The foil heater in the
pedestal assures dispense temperature of 110-130°F. This series has no heated line capability.
See below for individual model descriptions.
2396-00-100: Single Pedestal Topping Dispenser, with one open rack assembly.
2396-00-101: Single Pedestal Topping Dispenser, with one open rack assembly; unit
features an ADA Remote Switch.
2396-00-110: Double Pedestal Topping Dispenser, with one open rack assembly which
feeds both pedestals.
2396-00-111: Double Pedestal Topping Dispenser, with one open rack assembly which
feeds both pedestals; unit features two ADA Remote Switches.
2396-00-140: Double Pedestal Topping Dispenser, with one open rack assembly which
feeds both pedestals (has 5 ft. long tubing to pedestal).
Items Included with this Unit
Drip Pan
(4) Washers for
Pedestal Mounting
Drip Pan
Insert
(4) Wing Nuts for
Pedestal Mounting
Items shown are included for each pedestal.
Page 4
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Setup
This unit has been tested at the factory.
1. Remove all packaging and tape prior to installation.
2. The pedestal and rack assembly must be installed in a sturdy, level cabinet (provided
by the customer). Follow all instructions in the Electrical Requirement and Unit
Installation sections of this manual to complete installation of this unit.
3. After setup, the unit should be cleaned prior to use (see Care and Cleaning section of
this manual).
Control Box
6 Prong
Receptacle
Power Cord
Pedestal
Power Cord
Discharge Oil Line(s)
(connects to the pedestal)
Universal Bag Connector(s)
(connects to the topping bag)
Single pedestal model shown for general reference.
Page 5
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Electrical Requirements
The following power supply must be provided:
2396-00-100, 2396-00-101: 120 V~, 324 W, 60 Hz
2396-00-110, 2396-00-111, 2396-00-140: 120 V~, 390 W, 60 Hz
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
A certified electrician must furnish sufficient power for proper machine operation and install any
supplied receptacle. We recommend this equipment be on a dedicated and protected circuit.
Failure to wire properly will void the warranty and may result in damage to the machine. It is Gold
Medal Products Co.’s recommendation that this machine be plugged directly into a wall outlet. The
use of extension cords is not recommended due to safety concerns, and may cause sacrificed
and/or reduced performance. Make sure cord is located to prevent a trip hazard or unit upset.
Before You Plug In Machine
1. Make sure all machine switches are OFF before plugging equipment into receptacle.
2. Make sure wall outlet can accept the grounded plugs (where applicable) on the power
supply cord.
3. The wall outlet must have the proper polarity. If in doubt, have a competent
electrician inspect the outlet and correct if necessary.
4. DO NOT use a grounded to un-grounded receptacle adapter (where applicable).
5. Install unit in a level position.
CAUTION
If the supply cord is damaged, it must be replaced by Gold Medal Products Co.,
its service agent or similarly qualified persons in order to avoid a hazard.
039_080614
Page 6
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Unit Installation
Follow the instructions below to install the Topping Dispenser.
1. The bottom portion of the Topping Dispenser (the rack assembly) needs to be placed
in an area under the counter that can be enclosed on all sides in order for the heater to
properly maintain product temperature (cabinet to be provided by customer). Limit
the width of the cabinet to 3 feet, to ensure adequate cabinet temperature. Access will
be required to the front of this area allowing sufficient clearance to clean and maintain
the pump, and to add or remove boxes of topping.
2. The countertop will require preparation by drilling the mounting holes for the
pedestal, and by cutting the rectangular holes for the power cable and oil tube, drip
pan, and remote switch (if equipped). See Countertop Cutout Dimensions on next page
for reference. If your counter is thicker than the provided mounting studs attached to
the pedestal, then counter bore the underside of the countertop to allow for the washers
and wing nuts.
3. Set the pedestal onto the countertop and secure it in place with the wing nuts and
washers provided.
4. Set the rack assembly into the opening under the counter.
5. Attach the heated discharge oil-line tubing from the base to the aluminum tube on the
pedestal with the hose clamp provided (dual pedestal units will have 2 lines).
6. Plug the power cord from the pedestal(s) into the 6-prong receptacle on the side of the
control box (located on top of the rack assembly).
7. Plug the power cord from the rack assembly into a proper outlet (see Electrical
Requirements section).
8. If model is a dual pedestal unit, turn the power on and test the connections. Press the
dispense button and check to see that the correct pump is running to feed product to
the correct pedestal. If not, turn the power off and switch the six-prong plugs to the
opposite receptacles.
9. The unit is now ready to load boxes of topping, see Topping Installation section.
Page 7
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Countertop Cutout Dimensions
This section shows the placement, hole size and cutout dimensions to mount the pedestal(s),
drip pan, and ADA Remote (if equipped).
Single and Dual
Pedestal
15.500
4.625
3.219
1.297
2.688
2.594
1.609
3.094
8.750
PEDESTAL
MOUNTING
DRIP PAN
CUT-OUT
SPACED TO SUIT
n.375 THRU FOR
1/4-20 BOLTS (4)
3.219
1.297
2.688
2.594
1.609
3.094
PEDESTAL
MOUNTING
DRIP PAN
CUT-OUT
Models with ADA
Remote Switch
3.219
2.688
2.594
1.297
1.609
3.094
DRIP PAN
CUT-OUT
PEDESTAL
MOUNTING
8.750
EDGE OF COUNTER
n.375 THRU FOR
2.688
n .188 (4)
1.594
LOCATE FROM EDGE OF
COUNTER TO MEET 48"
ADA REACH LIMIT
.188
ADA
SWITCH
CUT-OUT
4.938
.188
1/4-20 BOLTS (4)
3.219
1.875" MIN
6.875" MAX
Dimensions for Single
Pedestal Model with
ADA Remote Switch
shown; space
accordingly for Dual
Pedestal Models with
ADA Remote Switches.
15.500
4.625
CABLE CONNECTING REMOTE SWITCH
TO PEDESTAL IS 20" LONG
Page 8
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Topping Installation
Use maximum of (2) 35 pound boxes of topping for this unit.
IMPORTANT: DO NOT attempt to operate this system with a bag which has been
removed from the box.
This product is not intended for use with volatile food products
(i.e. real butter).
1. Load two boxes of pre-heated topping onto the rack. Gold Medal’s Backroom Warmer
(Item No. 2262) may be purchased for pre-heating the topping.
Mount the box in the rack so the topping bag nozzle is located towards the bottom of
the box to permit a free flow of the topping from the bag.
2. Remove the cardboard cutout on the box to expose the bag nozzle, and then remove
the cap from the bag nozzle.
3. Attach the Universal Bag Connector (from the rack assembly) to the bag nozzle as
shown below. Once oil is connected, the unit is ready for use.
Steps to Attach the Universal Bag Connector
Universal Bag
Connector
Plunger OUT in
open position
Bag Nozzle
Step 1: Pull the Universal Bag Connector’s plunger out until it clicks into the open position.
Step 2: Grasp the Bag Nozzle
and slide the Bag Connector
on from the side.
Step 3: With the hose connector
in place, press plunger forward
to lock.
Page 9
Step 4: Connector shown
with plunger fully forward
in lock position.
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
OPERATING INSTRUCTIONS
Controls and Their Functions
HEAT SWITCH
Three position rocker switch.
• “Center” position is OFF.
• “Up” position is HEAT ONLY. This activates the display light, the heater/blower that
will maintain cabinet temperature, and activates the foil heater in the pedestal.
• “Down” position is PUMP & HEAT. This activates the display light, the heater/blower,
the foil heater in the pedestal, and provides power to the pump(s).
PUSH BUTTON PUMP SWITCH
There are two Push Button (PB) Pump Switches on a pedestal. One is located on the top of
the pedestal and the other is at the base of the pedestal. Press and hold button to dispense
butter flavored topping. Release button to stop dispensing topping.
ADA REMOTE - PUSH BUTTON PUMP SWITCH (for Model 2396-00-101 and 111 Only)
Press and hold the Remote PB Pump Switch to dispense butter flavored topping. Release
button to stop dispensing topping. (Dual Pedestal Models have an ADA Remote Switch for
each pedestal.)
RED PILOT LIGHT
Pilot Light located on the control box of the rack assembly. When lit, the red light signals
the pump is active. (Dual Pedestal Models have a Pilot Light for each pedestal.)
1 AMP FUSE
The 1 AMP Fuse protects the oil dispense unit from an overload condition. (Dual Pedestal
Models have a fuse for each pump.)
PB Pump
Switch
Red Pilot Light
Heat
Switch
1 AMP
Fuse
PB Pump
Switch
ADA Remote - PB Pump Switch
(Models 2396-00-101 and 111 Only)
Page 10
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Operating the Topping Dispenser
1. To Pump and Heat Topping - Turn the Heat Switch (located on control box) to the
PUMP & HEAT position to activate the display light, the heater/blower (to maintain
cabinet temperature), the foil heater in the pedestal, and provide power to the
pump(s).
2. To dispense topping - Press and hold either of the “Red” PB Pump Switches located
on the pedestal (or remote, if equipped). If this is the first time the unit has been used,
it may take a few seconds to completely fill the tube and dispense topping.
3. To use Heat Only -Turn the Heat Switch (located on control box) to the HEAT ONLY
position to activate the display light, the heater/blower (to maintain cabinet
temperature), and the foil heater in the pedestal.
On the HEAT ONLY setting the pump is de-activated.
Page 11
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Care and Cleaning
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
DO NOT immerse in water. DO NOT clean appliance with a water jet.
Always unplug the equipment before cleaning or servicing.
025_111616
WARNING
To avoid burns, DO NOT touch heated surfaces.
DO NOT place or leave objects in contact with heated surfaces.
009_092414
Good sanitation practice demands that all food preparation equipment be cleaned regularly (only
use non-toxic, food grade cleaners). A clean looking, well-kept machine is one of the best ways of
advertising your product.
Follow the directions below to clean and sanitize the unit each day after use.
1. Turn machine OFF, unplug the unit and allow it to cool before attempting to clean.
2. The exterior surfaces can be cleaned by wiping oil spills with a clean dry towel, then
wipe with another clean towel dampened with mild soap and warm water.
3. Wipe the stainless steel parts with a clean cloth and cleaner designed for stainless
steel, such as Gold Medal Watchdog Stainless Cleaner (Item No. 2088).
DO NOT use oven cleaners or abrasive materials as they will damage parts of machine.
4. Where applicable, drip pan/drip pan insert may be taken to the sink to clean with mild
soap and warm water. Allow to dry, then reassembly.
5. Clean plastic panels with glass cleaner. Gold Medal Watchdog Glass Cleaner (Item No.
2588) is recommended.
Ammonia cleaners will damage plastic panels. Use only non-ammonia cleaners, such
as Gold Medal Watchdog Glass Cleaner (Item No. 2588).
Sanitizing the Tubing and Pump
Items Needed: (2) Empty Pails
(1) Cleaning Bracket (Item No. 12594)
Gold Medal Chlor-Tech Sanitizer (Item No. 1109)
Measure Cup (for priming unit)
1. Make sure Topping Dispenser has cooled completely before attempting to clean.
2. Fill a clean, empty pail half-full with hot water and Gold Medal Chlor-Tech Sanitizer
(reference instructions on sanitizer container for appropriate amount).
Page 12
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
3. Disconnect Universal Bag Connector from topping bag, and connect it to cleaning
bracket as shown below. Make sure the quick disconnect is engaged.
Step 2:
Step 1:
Step 3:
Plunger OUT in
open position.
Cleaning
Bracket
Slide Connector
onto Bracket
Push Plunger IN to
lock onto bracket.
Plunger ENGAGED on pin.
4. Place hose with cleaning bracket into pail of sanitizing solution.
5. Place an empty pail under dispensing spout to receive cleaning solution pumped
through unit.
6. Use the “Red” PB Pump Switch (located on the pedestal, or remote, if equipped) to
dispense solution until tubes are clean and free of topping.
7. When pumping is complete, discard dirty solution, clean the pail, and refill with clean
hot water.
8. Remove hose with bracket from solution pail and place it in the hot water.
9. Place the empty pail under spout.
10. Use PB Switch to dispense hot water until tubes are clean and free of sanitizer.
11. When cleansing is complete, remove pail from dispenser.
12. Remove hose with bracket from hot water, disconnect bracket, and wipe hose and bag
connector dry.
13. Reconnect dispenser to bag of topping.
14. Purge and prime the system – hold a measuring cup (or medium sized container)
under dispenser spout; press the PB Switch to dispense topping until all water has
been expelled and tubes are primed with topping. After cleaning, always discard the
topping dispensed in priming.
15. Sanitize cleaning items for next use.
Page 13
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
MAINTENANCE INSTRUCTIONS
DANGER
Machine must be properly grounded to prevent electrical shock to personnel.
Failure to do so could result in serious injury, or death.
DO NOT immerse any part of this equipment in water.
DO NOT use excessive water when cleaning.
Keep cord and plug off the ground and away from moisture.
Always unplug the equipment before cleaning or servicing.
Make sure all machine switches are in the OFF position before plugging the
equipment into the receptacle.
008_051514
DANGER
Improper installation, adjustment, alteration, service, or maintenance can
cause property damage, injury, or death. Any alterations to this equipment
will void the warranty and may cause a dangerous condition. This appliance
is not intended to be operated by means of an external timer or separate
remote-control system. NEVER make alterations to this equipment. Read the
Installation, Operating, and Maintenance Instructions thoroughly before
installing, servicing, or operating this equipment.
014_020416
WARNING
No user serviceable parts inside. Refer servicing to qualified service
personnel.
011_051514
CAUTION
THE FOLLOWING SECTIONS OF THIS MANUAL ARE INTENDED ONLY
FOR QUALIFIED SERVICE PERSONNEL WHO ARE FAMILIAR WITH
ELECTRICAL EQUIPMENT. THESE ARE NOT INTENDED FOR THE
OPERATOR.
027_010914
Page 14
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
ORDERING SPARE PARTS
1. Identify the needed part by checking it against the photos, illustrations, and/or
parts list. (General images may be used in manual for reference only.)
2. Use only approved replacement parts when servicing this unit.
3. When ordering, please include part number, part name, and quantity needed.
4. Please include your model number, serial number, and date of manufacture (located
on the machine nameplate/data plate) with your order.
5. Address all parts orders to:
Parts Department
Gold Medal Products Co.
10700 Medallion Drive
Cincinnati, Ohio 45241-4807
Or, place orders by phone or online:
Phone: (800) 543-0862
(513) 769-7676
Fax:
(800) 542-1496
(513) 769-8500
E-mail: info@gmpopcorn.com
Web Page: gmpopcorn.com
Page 15
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Rack Assembly - Exterior View
239 6- 00 -1 00
1
2, 3
6
7, 8
9, 10
4
11
5
12, 13, 14
18, 19
17
16
15*
*CAUTION: If supply
cord is damaged, it
must be replaced by
Gold Medal Products
Co., its service agent,
or similarly qualified
persons in order to
avoid a hazard.
See Tubing and
Connectors Section
Single Pedestal Rack Assembly shown for reference
Item
Part Description
2396-00-100
2396-00-110
Part Number
2396-00-101
2396-00-111
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15*
16
17
18
19
COMPLETE RACK ASSEMBLY
CONTROL BOX
CONTROL BOX COVER
8-32 X 3/8 SLT. HWH M/S (screws to hold cover)
B.I.B. BUTTER PUMP
RETAINING STRAP
RED PILOT LIGHT
3 POSITION ROCKER SWITCH
SWITCH LABEL
FUSE HOLDER
1 AMP FUSE
SOCKET ASSEMBLY
6-32 X 3/8 PHIL PAN M/S (fastens socket assy.)
#6 INT. TOOTH L/W 410SS (fastens socket assy.)
6-32 M/S NUT 18-8 (fastens socket assy.)
LEAD-IN CORD 15 AMP PLUG
R 31-2 STRAIN RELIEF
HEAT DEFLECTOR
8-32 X 1/4 HX HD WHIZLOCK
ACORN NUT #8-32
77461
79375
79377
42044
79888
38998
41033
39410
39413
74636
79341
100299
39000
39001
14221
22038
41735
38995
42045
47702
79375
79377
42044
79888
38998
41033
39410
39413
74636
79341
100299
39000
39001
14221
22038
41735
38995
42045
47702
Page 16
2396-00-140
79375
79377
42044
79888
38998
41033
39410
39413
74636
79341
100299
39000
39001
14221
22038
41735
38995
42045
47702
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Tubing and Connectors
1
1
4
5
2
3
Item
1
2
3
4
5
Part Description
FOOD TUBING (replacement tubing is sold by
the foot)
SINGLE WIRE HOSE CLAMP
UNIVERSAL BAG CONNECTOR
IN LINE STRAINER
HOSE CLAMP
Page 17
Part Number
91375
75110
79100G
79269
67843
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Rack Assembly - Control Box Interior – Parts Breakdown
1
2
3
4, 5, 6
7
8
9
10
11, 12
13
14
15
16
General image of dual pedestal model shown for reference.
Page 18
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Rack Assembly - Control Box Interior – Parts List
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Part Description
120 VOLT 60 CY BLOWER
250 WATT 120 VOLT HEAT ELEMENT
EXHAUST BLOWER PLUG AND CORD
8-32 X 2 PH PAN M/S 18-8
#8 INT. TOOTH L/W 410SS
HEX NUT #8-32 STAINLESS
B.I.B. BUTTER PUMP
PILOT LIGHT-125V RED
3 POSITION ROCKER SWITCH
150 OHM RESISTOR AND DIODE ASSY
6-32 X 3/8 PHIL PAN M/S
6-32 M/S NUT 18-8
THERMOSTAT 135F
FUSE HOLDER
1 AMP FUSE
SOCKET ASSEMBLY
Page 19
Part Number
All Models
48018
38824
47199
39012
12132
89129
79888
41033
39410
55443
39000
14221
38990
74636
79341
100299
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Pedestal Exterior – Parts Breakdown
239 6- 00 -1 00
1
Light Cover
Assembly
2
3
4
5
6
7
15
8
9
10
16
Model 2396-00-100
Front View
Model 2396-00-100
Rear View
11
12
13
14
19
7
20
17
18
16
21
22
Pedestal and Remote Switch View
(Models 2396-00-101 and 111 Only)
Page 20
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Pedestal Exterior – Parts List
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Part Number
2396-00-100
2396-00-101
2396-00-110
2396-00-111
2396-00-140
Part Description
COMPLETE PEDESTAL
LIGHT COVER ASSEMBLY
(includes 2 screws, butter bracket, light cover)
SCREW #8 HEX WASHER HEAD
BUTTER BRACKET
LIGHT COVER
END CAP
PUSH DECAL
MOMENTARY SWITCH
NO DRIP SPOUT
DISPENSER LABEL
STRAIGHT CORD GRIP
SR 31-2 STRAIN RELIEF
PLUG WIRE HARNESS
FLAT WASHER 1/4 STAINLESS
1/4-20 ST STL WING NUT
PEDESTIAL BACK PLATE
SCREW #8-32X3/8 PAN HD PH
MOLDED RECEPTACLE
REMOTE SWITCH ASSEMBLY (complete assy.)
DECAL
SWITCH BOX
SWITCH BOX BASE
MOLDED PLUG
Page 21
77460
103160
103160
47771
103158
103159
69202
103081
38971
38566
39142
55234
41735
100301
87261
12466
38872
74141
47771
103158
103159
69202
103081
38971
38566
39142
55234
41735
100301
87261
12466
38872
74141
41712
39154
39181
39152
39153
47726
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Top Pedestal – Interior View
Power Supply is
located on back of
Support Plate.
1
2
3
8
9
10 11
4
5
LED Support Plate
6, 7
12, 13
View under LED Support Plate
Item
1
2
3
4
5
6
7
8
9
10
11
12
13
Part Description
6 1W LED STRIP
SCREW #8 HEX WASHER HEAD
LED SUPPORT PLATE 2499
TOP PEDISTAL PLATE 2499
POWER SUPPLY 24VDC 20W
6-32 X 1/2 SL PAN HD M/S
6-32 HEX NUT ZINC PLATED
BUSHING, SNAP .875 IN
MOMENTARY SWITCH
NO DRIP SPOUT
1/2 FLAT WASHER, S.S.
SPOUT (Aluminum Dispense Tube)
FOIL HEAT ELEMENT 8W 120V
Page 22
Part Number
All Models
55379
47771
69167
69168
55394
47516
38005
45396
38971
38566
12627
103082
38970
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Safety Labels
4
1
2
3
5
6
Unit Labels
7
Power Cord Label
Item
1
2
3
4
5
6
7
Part Description
HOSE CONNECT LABEL
WARNING LABEL MAX FUSE 1A
LBL CAUTION DISCONNECT PR
SERVICE LABEL
LBL WARN DISCONNECT POWER
LABEL SAFE OPERATING INST
WARNING LABEL CORD
Part Number
All Models
79388
79343
87149
87935
74119
47010
68720
Accessories
1
2
Item
1
2
Part Description
DRIP PAN
PAN INSERT WELDMENT
Page 23
Part Number
All Models
69148
69201
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
Wiring Diagram
All Models
Page 24
gmpopcorn.com
Popcorn Topping
Dispenser
Model Series 2396-00-100 (101, 110, 111, and 140)
WARRANTY
WARRANTY
+
Gold Medal Products Co. warrants to the original purchaser each item of its manufacture to
be free of defects in workmanship and material under normal use and service. Gold Medal
Products Co.’s obligation under this warranty is limited solely to repairing or replacing parts,
f.o.b. Cincinnati, Ohio, which in its judgment are defective in workmanship or material and
which are returned, freight prepaid, to its Cincinnati, Ohio factory or other designated point.
Except for “Perishable Parts” on specific machines, the above warranty applies for a period
of two (2) years from the date of original sale to the original purchaser of equipment when
recommended operating instructions and maintenance procedures have been followed. These
are packed with the machine. Parts warranty is two (2) years, labor is six (6) months.
THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR
IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART,
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY. THERE ARE
NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE
HEREOF. In no event shall Gold Medal Products Co. be liable for special, incidental or
consequential damages. No claim under this warranty will be honored if the equipment covered
has been misused, neglected, damaged in transit, or has been tampered with or changed in any
way. No claim under this warranty shall be honored in the event that components in the unit at
the time of the claim were not supplied or approved by Gold Medal Products Co. This warranty
is effective only when electrical items have been properly attached to city utility lines only at
proper voltages. This warranty is not transferable without the written consent of Gold Medal
Products Co.
The term “Original Purchaser” as used in this warranty shall be deemed to mean that person,
firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS CO.,
or their authorized distributor for the equipment.
THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL
PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS CO. AT 1-800-543-0862 TO
DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM,
AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR
REPLACEMENT OF PARTS.
NOTE: This equipment is manufactured and sold for commercial use only.
10700 Medallion Drive, Cincinnati, Ohio 45241-4807 USA
gmpopcorn.com
Phone: (800) 543-0862
(513) 769-7676
Fax: (800) 542-1496
(513) 769-8500
© 2017 – The text, descriptions, graphics, layout, and other material in this publication are the exclusive property of
Gold Medal Products Co. and shall not be used, copied, reproduced, or published in any fashion, including website
display, without its express written consent.
Page 25
gmpopcorn.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising