Ursalink UR72 Industrial Cellular Router Quick Start Guide

UR72 & UR75
Industrial Cellular Router
Quick Start Guide
1
Ursalink Technology Co., Ltd.
Welcome
Thank you for choosing Ursalink UR72/UR75 industrial cellular router.
This guide describes how to install the UR72/UR75 and how to log in the Web GUI to configure the device.
Once you complete the installation, refer to the Ursalink UR72/UR75 User Guide for instructions on how to
perform configurations on the device.
Related Documents
This Start Guide only explains the installation of Ursalink UR72 & UR75 router. For more functionality and
advanced settings, please refer to the relevant documents as below.
Document
Ursalink UR72/UR75 Datasheet
Ursalink UR72/UR75 User Guide
Description
Datasheet for the Ursalink UR72/UR75 industrial cellular router.
Users could refer to the guide for instruction on how to log in the
web GUI, and how to configure all the settings.
The related documents are available on Ursalink website: http://www.ursalink.com.
Declaration of Conformity
UR72 & UR75 are in conformity with the essential requirements and other relevant provisions of the CE, FCC,
and RoHS.
For assistance, please contact
Ursalink technical support:
Email: support@ursalink.com
Tel: 86-592-5023060
Fax: 86-592-5023065
www.ursalink.com
1
Ursalink UR72 & UR75 Quick Start Guide
1. Packing List
Before you begin to install the UR72/UR75 router, please check the package contents to verify that you have
received the items below.
1.1 Package Contents
1 × UR72 Router
or
1 × UR75 Router
1 × Ethernet Cable
1 × Power Adapter
2 × SIM Card Slots
1 × DIN Rail Kit (Default)
1 × 2-Pin Pluggable
Terminal
1 × 10-Pin Pluggable
Terminal
1 × Warranty Card
1 × Quick Start Guide
2 × Magnetic Mount
2 × Stubby Cellular
Cellular Antennas (Default) Antennas (Optional)
2 × Stubby Wi-Fi
Antennas (Optional)
2 × Rack Mount Kits
(Optional)
1 × Wall Mounting Bracket
(Optional)
If any of the above items is missing or damaged, please contact your Ursalink sales
representative.
www.ursalink.com
2
Ursalink UR72 & UR75 Quick Start Guide
2. Hardware Introduction
2.1 Overview
A. Front Panel
UR72 Front Panel
1
2
3
4
5
6
7
8
9
UR75 Front Panel
1
2
3
4
5
6
7
8
9
www.ursalink.com
Main Cellular Antenna Connector
Reset Button
LED Indicator Area
POWER: Power Indicator
STATUS: Status Indicator
WLAN: Wi-Fi Indicator
VPN: VPN Indicator
SIM 1: SIM 1 Status Indicator
SIM 2: SIM 2 Status Indicator
: Signal Strength Indicator
Ethernet Port Indicator
Orange for data transmission;
Green for network rate
AUX Cellular Antenna
WLAN 2: Wi-Fi Antenna Connector 2
Serial Port & I/O
GPS: GPS Antenna Connector
WLAN 1: Wi-Fi Antenna Connector 1
Main Cellular Antenna Connector
Reset Button
LED Indicator Area
POWER: Power Indicator
STATUS: Status Indicator
WLAN: Wi-Fi Indicator
VPN: VPN Indicator
SIM 1: SIM 1 Status Indicator
SIM 2: SIM 2 Status Indicator
: Signal Strength Indicator
Ethernet Port Indicator
Orange for data transmission;
Green for network rate
AUX Cellular Antenna
WLAN 2: Wi-Fi Antenna Connector 2
Serial Port & I/O
GPS: GPS Antenna Connector
WLAN 1: Wi-Fi Antenna Connector 1
3
Ursalink UR72 & UR75 Quick Start Guide
B. Left Side Panel
SIM Card Slot
Power Connector
Grounding Stud
1
2
3
2.2 Dimensions (mm)
2.3 Pinouts
www.ursalink.com
PIN
1
2
3
4
5
6
7
8
9
RS232
TXD
RXD
----GND
---------
RS485
----A
B
-----------
DI
--------GND
IN1
IN2
-----
DO
--------------OUT1
OUT2
10
---
---
---
COM
Description
Transmit Data
Receive Data
Data +
Data Ground
Digital Input1
Digital Input2
Digital Output1
Digital Output2
Common
Ground
4
Ursalink UR72 & UR75 Quick Start Guide
PIN
11
12
Description
Positive
Negative
2.4 LED Indicators
LED
Indication
POWER
Power Status
STATUS
System Status
VPN
VPN Status
WLAN (Wi-Fi)
WLAN Status
Status
On
Off
Green Light
Red Light
Green Light
Off
Green Light
Off
Off
SIM1/SIM2
SIM Card Status
Green Light
Off
Signal Strength Signal 1/2/3
Green Light
Description
The power is switched on
The power is switched off
Static: Start-up
Blinking slowly: the system is running properly
The system goes wrong
VPN is connected
VPN is disconnected
Static: Wi-Fi is enabled
Blinking slowly: sending or receiving data via Wi-Fi
Wi-Fi is disabled
SIM1 or SIM2 is registering or fails to register (or
there are no SIM cards inserted)
Blinking slowly: SIM1 or SIM2 has been registered
and is ready for dial-up
Blinking rapidly: SIM1 or SIM2 has been registered
and is dialing up now
Static: SIM1 or SIM2 has been registered and dialed
up successfully
No signal
Static/Off/Off: weak signals with 1-10 ASU (please
check if the antenna is installed correctly, or move the
antenna to a suitable location to get better signal)
Static/Static/Off: normal signals with 11-20 ASU
(average signal strength)
Static/Static/Static: strong signals with 21-31 ASU
(signal is good)
2.5 Reset Button
www.ursalink.com
5
Ursalink UR72 & UR75 Quick Start Guide
Function
Reboot
Reset
Description
STATUS LED
Blinking
Static Green
Blinking
Static Green →
Rapidly Blinking
Off → Blinking
Action
Press and hold the reset button for about 5-15 seconds.
Release the button and wait for system to reboot.
Press and hold the reset button for more than 15 seconds.
Release the button and wait.
The router is now reset to factory defaults.
2.6 Ethernet Port Indicator
Indicator
Link Indicator (Orange)
Rate
Indicator (Green)
www.ursalink.com
Status
On
Blinking
Off
On
Off
Description
Connected
Transmitting data
Disconnected
1000 Mbps mode
100 Mbps mode
6
Ursalink UR72 & UR75 Quick Start Guide
3. Hardware Installation
Environmental Requirements
- Power Input: 9-48 VDC
- Power Consumption: Typical 2.6W (Max 4.5 W) for UR72
Typical 3.0 W (Max 5.5 W) for UR75
- Operating Temperature: -20°C to 70°C (4°F -158°F)
- Relative Humidity: 0% to 95% (non-condensing) at 25°C/77°F
3.1 SIM Card/Micro SD Card/SSD Installation
3.1.1 SIM Card Installation
A. Push the yellow button on the left panel of the
slot router, and then you will see the SIM card
slot popping out directly.
B. Put SIM card onto the slot then insert the
back into the hole.
3.1.2 Micro SD Card Installation
A. Unscrew the cover on the left panel
of the router and then take it off.
www.ursalink.com
B. Insert Micro SD card.
7
Ursalink UR72 & UR75 Quick Start Guide
C. Close the cover and screw it back to the router.
3.1.3 SSD Installation
Before installing SSD, please turn off the power.
A. Unscrew the enclosure, and then remove the cover.
B. Unscrew the main-board, find the interface on the rear side of the main-board and then insert SSD.
www.ursalink.com
8
Ursalink UR72 & UR75 Quick Start Guide
C. Screw the main-board on the cabinet and close the cover.
3.2 Rotate the Antenna into the Antenna Connector
The external antenna should be installed vertically always on a site with a good cellular signal.
3.3 Connect the Router to a Computer.
Please connect PC to any port among GE 1/1-GE 1/4 of UR75 router, or to GE 1 of UR72 router directly.
3.4 Mount the Router
The router can be placed on a desktop or mounted to a wall or a DIN rail.
3.4.1 Wall Mounting (Measured in mm)
Use 2 pcs of M3 × 6 flat head Phillips screws to fix the wall mounting kit to the router, and then use 2 pcs of
M3 drywall screws to mount the router associated with the wall mounting kit on the wall.
www.ursalink.com
9
Ursalink UR72 & UR75 Quick Start Guide
Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.
3.4.2 DIN Rail Mounting (Measured in mm)
Use 2 pcs of M3 × 6 flat head Phillips screws to fix the DIN rail to the router, and then hang the DIN rail on
the mounting bracket. It is necessary to choose a standard bracket.
Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.
3.5 Power Supply Installation
A. Take out the terminal from the router and unscrew the bolt on terminal.
B. Screw down the bolt after inserting power cable into the terminal.
Connecting the Power Cable
Color
Red
Yellow
Polarity
+
-
If you insert wires into the reverse holes, the router will not start and you must switch the wires
into the correct holes.
3.6 Protective Grounding Installation
A. Remove the grounding nut.
B. Connect the grounding ring of the cabinet’s grounding wire onto the grounding stud and screw up the
www.ursalink.com
10
Ursalink UR72 & UR75 Quick Start Guide
grounding nut.
The router must be grounded when deployed. According to operating environment, the ground wire
should be connected with grounding stud of router.
www.ursalink.com
11
Ursalink UR72 & UR75 Quick Start Guide
Getting Started
4. PC Configuration for Web GUI Accessing to Router
Please connect PC to any port among GE 1/1-GE 1/4 of UR75 router, or to GE 1 of UR72 router directly. PC
can obtain an IP address, or you can configure a static IP address manually. The following steps are based on
Windows 10 operating system for your reference.
(Note: As remote access is disabled by default, you can't access to the router's Web GUI if you connect PC to
GE 0 of the router. But it will function properly if you enable it on the Web GUI.)
① Click “Search Box” to search “Control Panel” on the
Windows 10 taskbar.
③ Click “Ethernet” (May have different names).
www.ursalink.com
② Click “Control Panel” to open it, and then click
“View network status and tasks”.
④ Click “Properties”.
12
Ursalink UR72 & UR75 Quick Start Guide
⑤ Double Click “Internet
Protocol Version 4
(TCP/IPv4)” to configure IP
address and DNS server.
⑥ Method 1: click “Obtain an IP
address automatically”;
Method 2: click “Use the
following IP address” to assign a
static IP manually within the
same subnet of the router.
(Note: Remember to click “OK” to finish configuration.)
www.ursalink.com
13
Ursalink UR72 & UR75 Quick Start Guide
5. Access to Web GUI of Router for Cellular Connection
This chapter explains how to log in UR72/UR75 router’s Web GUI, and connect the router to cellular
network.
Ursalink router provides Web-based configuration interface for management. If this is the first time you
configure the router, please use the default settings below:
IP Address: 192.168.1.1
Username: admin
Password: password
5.1 To Log in the Router
Make sure your PC is connected to the same network as the router as per Section 4.
A. Start a Web browser on your PC (Chrome and IE are recommended), type in the IP address, and press
Enter on your keyboard.
B. Enter the username and password, click “Login”.
If you enter the username or password incorrectly more than 5 times, the login page will be locked
for 10 minutes.
C. When you log in with the default username and password, you will be asked to modify the password. It’s
suggested that you change the password for the sake of security. Click “Cancel” button if you want to modify
it later.
www.ursalink.com
14
Ursalink UR72 & UR75 Quick Start Guide
D. After you log in the Web GUI, you can view system information and perform configuration on the router.
5.2 Configure the Cellular Connection
Take inserting SIM card into SIM1 slot as an example; please refer to the following detailed operations.
A. Click “Network” → “Interface” → “Cellular” → “Cellular Setting” to configure the cellular info.
B. Enable SIM1.
C. Choose relevant network type. “Auto”, “4G First”, “4G Only”, “3G First”, “3G Only”, “2G First” and “2G
Only” are optional.
D. Click “Save” and “Apply” for configuration to take effect.
www.ursalink.com
15
Ursalink UR72 & UR75 Quick Start Guide
If you select “Auto”, the router will obtain ISP information from SIM card to set APN, Username, and
Password automatically. This option will only be taken effect when the SIM card is issued from a well-known
ISP.
If you select “4G First” or “4G Only”, you can click “Save” to finish the configuration directly.
If you select “3G First”, “3G Only”, “2G First” or “2G Only”, you should manually configure APN, Username,
Password, and Access Number.
UR72 & UR75 routers have two cellular interfaces, named SIM1 & SIM2. Only one cellular interface is active
at one time. If both cellular interfaces are enabled, SIM1 interface takes precedence by default.
5.3 Check the Cellular Connection Status
5.3.1 Check the Cellular Connection Ctatus by Web GUI of Router
Click “Status” → “Cellular” to view the status of the cellular connection. If it shows “Connected”, it means
SIM1 has dialed up successfully.
www.ursalink.com
16
Ursalink UR72 & UR75 Quick Start Guide
5.3.2 Check the Cellular Connection Status by Hardware
On the other hand, you can check the status of SIM1 indicator. If it keeps on green light statically, it means
SIM1 has dialed up successfully.
5.4 Check out if Network Works Properly by Browser on PC
Open your preferred browser on PC, then type any available web address into address bar and see if it is
able to visit Internet via UR72/UR75 router.
[END]
www.ursalink.com
17
Download PDF