Samsung | 460P | Samsung 460P User Manual

Install Pro grams
SyncMaster 460Pn/460P
Notational
Failure to follow directions noted by this symbol could result in bodily harm or damage to
equipment.
Prohibited
Important to read and understand at all times
Do not disassemble
Disconnect the plug from the outlet
Do not touch
Grounding to prevent an electric shock
Power
When not used for an extended period of time, set your computer to DPMS.
If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug.
z
This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands.
z
This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle.
z
An improper ground may cause electric shock or equipment damage.
Insert the power plug firmly so that it does not come loose.
z
A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects upon them,
which could cause damage.
z
This may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet.
z
This may cause fire.
Installation
Be sure to contact an authorized Service Center, when installing your monitor in a
location with the heavy dust, high or low temperatures, high humidity, chemical
substance and where it operates for 24 hours such as the airport, the train station or
etc.
Failure to do so may cause a serious damage to your monitor.
Put your monitor in a location with low humidity and a minimum of dust.
z
Failure to do so may cause an electric shock or fire inside the monitor.
Do not drop the monitor when moving it.
z
This may cause damage to the product or human body.
Install the monitor base in a showcase or shelf so that the end of the base
does not protrude from the showcase or shelf.
z
Dropping the product may cause damage to the product or personal injury.
Do not place the product on an unstable or small surface area.
z
Place the product on an even, stable surface, as the product may fall and
cause harm to someone walking by, specifically children.
Do not place the product on the floor.
z
Someone, specifically children could trip over it.
Keep any flammable objects such as candles, insecticides or cigarettes
away from the product.
z
Otherwise, this may cause a fire.
Keep any heating devices away from the power cable.
z
A melted coating may lead to electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a
bookshelf, closet, etc.
z
Any increase in internal temperature may cause fire.
Set down the monitor carefully.
z
The monitor could be damaged or broken.
Do not place the monitor face down.
z
The TFT-LCD surface may be damaged.
Installing a wall bracket must be done by a qualified professional.
z
z
Installation by unqualified personnel may result in injury.
Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall (more
than 10cm/4inch ) for ventilation purposes.
z
Poor ventilation may cause an increase in the internal temperature of the
product, resulting in a shortened component life and degraded performance.
Clean
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a
slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor.
z
This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly
with a dry cloth.
z
A dirty connector may cause an electric shock or fire.
Make sure to unplug the power cord before cleaning the product.
z
Otherwise, this may cause electric shock or fire.
Unplug the power cord from the power outlet and wipe the product using a
soft, dry cloth.
z
Do not use any chemicals such as wax, benzene, alcohol, thinners,
insecticide, air freshener, lubricant or detergent.
Contact the Service Center or Customer Center for interior cleaning once a
year.
z
Keep the product's interior clean. Dust which has accumulated in the interior
over an extended period of time may cause malfunction or fire.
Others
Do not remove cover (or back).
z
z
This may cause an electric shock or fire.
Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any
unusual sounds or smells coming from it - unplug it immediately and
contact an authorized dealer or service.
z
This may cause an electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do
not install inside a vehicle.
z
z
This may cause malfunction, an electric shock or fire.
Especially avoid operating the monitor near water or outdoors where it
could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and
unplug the power cord. Then contact the Service Center .
z
The monitor may malfunction, causing an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is not
used for a long period of time.
z
Failure to do so may cause an electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable.
z
This may cause a breakdown, electric shock or fire due to damage to the
cable.
Do not move the monitor right or left by pulling only the wire or the signal
cable.
z
This may cause a breakdown, electric shock or fire due to damage to the
cable.
Do not cover the vents on the monitor cabinet.
z
Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on
the monitor.
z
z
This may cause malfunction, an electric shock or fire.
If a foreign substance enters the monitor, unplug the power cord and
contact the Service Center.
Keep the product away from combustible chemical sprays or inflammable
substances.
z
This may cause an explosion or fire.
Never insert anything metallic into the monitor openings.
z
This may cause an electric shock, fire or injury.
Do not insert metal objects such as chopsticks, wire and gimlet or
inflammable objects such as paper and match into the vent, headphone port
or AV ports.
z
It may cause a fire or an electric shock. If an alien substances or water
flows into the product, turn the product off, unplug the power connector
from the wall outlet and contact Service Center.
If you view a fixed screen for an extended period of time, residual image or
blurriness may appear.
z
Change the mode to energy save or set a screensaver to moving picture
when you need to be away from the monitor for an extended period of time.
Adjust the resolution and frequency to the levels appropriate for the model.
z
Inappropriate resolution may cause undesirable picture quality.
46 inch - 1360 X 768
Watching the monitor continuously at a too close angle may result in
eyesight damage.
To ease eye strain, take at least a five-minute break after every hour of
using the monitor.
Do not install the product on an unstable, uneven surface or a location
prone to vibrations.
z
Dropping the product may cause damage to the product or personal injury.
Using the product in a location prone to vibrations may shorten the lifetime
of the product or may catch fire.
When moving the monitor, turn off and unplug the power cord.
Make sure that all cables, including the antenna cable and cables
connecting to other devices, are disconnected before moving the monitor.
z
Failure to disconnect cables may damage it and lead to fire or an electric
shock.
Make sure there are more than two people when moving the product.
z
Dropping the product may cause a malfunction or physical damage.
Place the product out of children’s reach, as they could damage it by
hanging onto it.
z
A falling product could cause physical damage even death.
When not using the product for an extended time period, keep the product
unplugged.
z
Otherwise, this may cause heat emission from the accumulated dirt or
degraded insulation, leading to electric shock or fire.
Do not place children’s favorite objects (or anything else that may be
tempting) on the product.
z
Children may try to climb on the product to retrieve an object. The product
could fall, causing physical damage or even death.
When you remove batteries from the remote, be careful that they are not
swallowed by children. Keep batteries out of the reach of children.
z
If swallowed, see a doctor immediately.
When replacing batteries, place the batteries in the correct +/- polarity
position as indicated on battery holder.
z
Incorrect polarity may cause a battery to break or leak and could lead to
fire, injury, or contamination (damage).
Use only specified standard batteries. Do not use new and used batteries
together.
z
This may cause a battery to break or leak and could lead to fire, injury, or
contamination (damage).
The battery (and rechargeable battery) are not ordinary refuse and must be
returned for recycling purposes. The customer is responsible for returning
the used or rechargeable battery for recycling purposes as the consumer of
the battery.
z
The customer can return the used or rechargeable battery to a nearby
public recycling center or to a store selling the same type of the battery or
rechargeable battery.
SyncMaster 460Pn
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
This stand is not for the Floor Standing Type.
Unpacking
Monitor
Manual
Quick Setup Guide
Cable
Warranty Card
(Not available in all locations)
User's Guide, MDC software,
Natural Color software,
MagicNet software
D-Sub Cable
Power Cord
Speaker Wire Cable
Wall Mount KIT
Speaker Set
Stand KIT
DVI Cable
LAN Cable
Remote Control
Batteries (AAA X 2)
BNC to RCA
Adapter Jack
Semi Stand
Sold separately
Others
Cover-Hole
Front
1. MENU
6. PIP
2. Navigate button (Up-Down button)
7. Power button
3. Adjust button (Left-Right button)/
Volume button
8. Power indicator
4. ENTER
9. Remote Control Sensor
5. SOURCE
1. MENU
Use this button to open the on-screen menu and exit from the menu screen or close screen
adjustment menu.
2. Navigate buttons (Up-Down button)
Moves from one menu item to another vertically or adjusts selected menu values.
3. Adjust buttons (Left-Right button) / Volume buttons
Moves from one menu item to another horizontally or adjusts selected menu values.
Adjusts the audio volume.
4. ENTER
Activates a highlighted menu item.
5. SOURCE
Switches from PC mode to Video mode.
Changing the source is allowed only in external devices that are connected to the monitor
at the time.
To switch Screen modes:
[PC]
[BNC]
[DVI]
[AV]
[S-VIDEO]
[Component]
[MagicNet]
>>Click here to see an animation clip
6. PIP
Push the PIP button to turn PIP screen On/Off.
More than one PIP couldn't be overlapped on screen as BNC and the component use the
same terminal.
>>Click here to see an animation clip
• PC / DVI
: AV / S-Video / Component Mode
• BNC
: AV / S-Video Mode
• AV / S-Video
: PC / BNC / DVI Mode
• Component
: PC / DVI Mode
7. Power button
Use this button to turn the monitor on and off.
8. Power indicator
Power Indicator shows PowerSaver mode by green blinking.
9. Remote Control Sensor
Aim the remote control towards this spot on the Monitor.
See PowerSaver described in the manual for further information regarding power saving functions.
For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended
for long periods.
Rear
For detailed information concerning cable connections, refer to Connecting Cables under Setup.
The monitor's rear configuration may vary slightly depending on the monitor model.
1.
POWER SW : Switch the monitor on and off.
2.
POWER IN : Power cord, plug into monitor
and wall receptacle.
3.
RS232C OUT/IN (RS232C Serial PORT): MDC(Multiple Display Control) Program Port
4.
DVI IN(HDCP) (PC Video Connection Terminal)
: Using DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC)
5.
PC IN(RGB) (PC Video Connection Terminal)
: Using D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC)
6.
PC/DVI/BNC AUDIO IN (PC/DVI/BNC Audio Connection Terminal (Input))
7.
COMPONENT AUDIO IN [L-AUDIO-R](Component Audio Connection Terminal
(Input))
8.
BNC/COMPONENT OUT (BNC/Component Connection Terminal (Output))
- BNC (Analog PC) Connection : connecting R, G, B, H, V port
- Component Connection : connecting PR, Y, PBport
9.
BNC/COMPONENT IN (BNC/Component Connection Terminal (Input))
10. AV AUDIO IN [L-AUDIO-R](Monitor Audio Connection Terminal (Input))
11. AV OUT [VIDEO](VIDEO Connection Terminal) : AV mode (Output)
12. AV IN [VIDEO](VIDEO Connection Terminal) (Input)
13. AV OUT [S-VIDEO](S-Video Connection Terminal) : S-Video mode (Output)
14. AV IN [S-VIDEO](S-Video Connection Terminal) (Input)
15. EXT SPEAKER(8 Ω) (EXT Speaker Connection Terminal)
16. MONITOR OUT [L-AUDIO-R](Monitor Audio Connection Terminal (Output))
- MONITOR OUT is the terminal for sound output of PC, DVI or BNC.
The number of monitors that can be connected to loopout may be different
under the circumstance such as cable, signal source, etc.
With a cable which there is no degradation or signal source ten monitors can be
connected.
17.
LAN (LAN Connection Terminal)
(MS Internet Explorer)
18.
USB (USB Connection Terminal)
(Keyboard / Mouse, Mass Storage Device Compatible.)
19.
DIGITAL AUDIO OUT (Digital Audio Connection Terminal)
20. Kensington Lock
The Kensington lock is a device used to
physically fix the system when using it in a
public place.
(The locking device has to be purchased
separately. )
For using a locking device, contact where
you purchase it.
See Connecting the Monitor for further information regarding cable connections.
Remote Control
The performance of the remote control may be affected by a TV or other electronic devices operated
near the monitor, causing malfunction due to interference with frequency.
1. ON / OFF
2. MAGICNET
3. MDC
4. LOCK
5. MagicNet buttons
6. +100
7. VOL
8. MUTE
9. AUTO
10. MENU
11. ENTER
12. PRE-CH
13. CH/PAGE
14. SOURCE
15. INFO
16. EXIT
17. Up-Down Left-Right buttons
18. P.MODE (M/B)
19. STILL
20. BBE
21. MTS
22. PIP
23. SOURCE
24. SIZE
25. SWAP
26.
27.
28.
29.
MagicNet Remote Control
1. ON / OFF
Use these buttons to turn the monitor on or off.
2. MAGICNET
MagicNet Quick Launch Button.
3. MDC
MDC Quick Launch Button.
4. LOCK
This button will activate or deactivate all function keys on both the remote control and the monitor
except for the Power and LOCK buttons.
5. MagicNet buttons
- Used for MagicNet.
z
z
z
z
Alphanumeric: Used to enter the Internet address.
DEL : Functions as the backspace.
SYMBOL : Used to enter the symbols. (.O_-:/)
ENTER : Used to enter values.
6. +100
Press to select channels over 100.
For example, to select channel 121, press "+100", then press "2" and "1".
- This fuction does not work for this monitor.
7. VOL
Adjusts the audio volume.
>>Click here to see an animation clip
8. MUTE
Pauses (mutes) the audio output temporarily.
Displayed on the lower left corner of the screen.
The audio resumes if MUTE or - VOL + is pressed in the Mute mode.
9. AUTO
Adjusts the screen display automatically.
If you change resolution in the control panel, auto function will be executed.
10. MENU
Use this button to open the on-screen menu and exit from the menu screen or close screen
adjustment menu.
11. ENTER
Activate a highlighted menu item.
12. PRE-CH
This button is used to return to the immediately previous channel.
- This fuction does not work for this monitor.
13. CH/PAGE
Selects channels or page.
- This fuction does not work for this monitor.
14. SOURCE
Push this button to change video sources.
15. INFO
Current picture information displays on the upper left corner of the screen.
16. EXIT
Exits from the menu screen.
17. Up-Down Left-Right buttons
Moves from one menu item to another horizontally, vertically or adjusts selected menu values.
18. P.MODE (M/B)
When you press this button, current picture mode is displayed on the lower center of the screen.
AV / S-Video / Component : P.MODE
The Monitor has four automatic picture settings that are preset at the factory.
Then push button again to circle through available preconfigured modes.
( Dynamic
Standard
Movie
Custom )
PC/DVI/BNC : M/B (MagicBright™)
MagicBright™ is a new feature providing the optimum viewing environment depending on the
contents of the image you are watching.
Then push button again to circle through available preconfigured modes.
(Entertain
Internet
Text
Custom )
19. STILL
When you press this button, STILL is displayed on the lower center of the screen.
Press the button once to freeze the screen.
Press it again to unfreeze.
20. BBE
Recreates the natural sound and improves sound clarity through boosting high and low range
frequencies. As a result high sounds are clearer, brilliant and finely detailed while low sounds are
tight, well-defined and harmonically rich.
21. MTS
You can select the MTS (Multichannel Television Stereo) mode.
FM Stereo
Audio Type
MTS/S_Mode
Mono
Mono
Stereo
SAP
Mono
Stereo
Mono
SAP
Default
Manual Change
Mono
- This fuction does not work for this monitor.
22. PIP
Every time you push the button, a PIP screen appears.
23. SOURCE
The PIP window's signal source changes.
24. SIZE
You can switch the Picture Size.
25. SWAP
Swapping the contents of the PIP and main image.
The image in the PIP window will appear on the main screen, and the main screen image will
appear in the PIP window.
26.
Rewind
27.
Stop
28.
Play/Pause
29.
Fast forward
Remote Control
PHOTO
z
When the files are selected in the library list
Previous file
Stop slideshow / View the bottom menu bar
Slideshow
Next file
z
When you see no menu in a zoomed-in picture
Move up to the top of the image
Move down to the bottom of the image
Move to the left of the image
Move to the right of the image
MUSIC
z
When the files are selected in the library list
File view on the cursor position /
Play / Pause during playback
Stop playing
Play in 5 seconds
Play 5 seconds earlier
Move to the next page (when the cursor is placed at the
top, it will go back to the last file of the previous page)
Move to the previous page (when the cursor is placed at
the bottom, it will move to the first file of the next page)
Move to the next page (when the current page is the first,
it will move to the last page)
Move to the previous page (when the current page is the
last, it will move to the first page)
File view on the cursor position Play
MOVIE
z
When the files are selected in the library list
Move to the top (when the cursor is placed at the top, it
will go back to the last file of the previous page)
Move to the bottom (when the cursor is placed at the
bottom, it will move to the first file of the next page)
Move to the next page (when the current page is the first,
it will move to the last page)
Move to the previous page (when the current page is the
last, it will move to the first page)
File view on the cursor position Play
z
Play
Play / Pause during playback
Stop playing
Play 5 seconds earlier
Play in 5 seconds
OFFICE
z
When the files are selected in the library list
Move to the top (when the cursor is placed at the top, it
will go back to the last file of the previous page)
Move to the bottom (when the cursor is placed at the
bottom, it will move to the first file of the next page)
Move to the next page (when the current page is the first,
it will move to the last page)
Move to the previous page (when the current page is the
last, it will move to the first page)
File view on the cursor position
z
PDF
Move to the top
Move to the bottom
Move to the next page
Move to the previous page
Exit PDF
z
Excel
Move to the upper cell
Move to the lower cell
Move to the left cell
Move to the right cell
Move to the next page
Move to the previous page
Move to the right sheet
Move to the left sheet
Exit Excel
z
Power point Normal
Move to the top
Move to the previous page
Move to the next page
Move to the previous page
Slideshow
Exit Power point
z
Power point Slideshow
Stop slideshow
Move to the top
Move to the bottom
Move to the next page
Move to the previous page
Exit Power point
z
Word
Move to the top
Move to the bottom
Move to the next page
Move to the previous page
Exit Word
z
HTML / Ineternet
Move the mouse cursor up
Move the mouse cursor down
Move the mouse cursor to the left
Move the mouse cursor to the right
Click when the cursor is placed over a link (move to the
link)
Exit the Internet
SyncMaster 460P
Please make sure the following items are included with your monitor.
If any items are missing, contact your dealer.
Contact a local dealer to buy optional items.
This stand is not for the Floor Standing Type.
Unpacking
Monitor
Manual
Quick Setup Guide
Cable
Warranty Card
(Not available in all locations)
User's Guide, MDC software,
Natural Color software
D-Sub Cable
Power Cord
Speaker Wire Cable
Wall Mount KIT
Speaker Set
Stand KIT
Remote Control
Batteries (AAA X 2)
Cover-Hole
BNC to RCA
Adapter Jack
Semi Stand
Sold separately
DVI Cable
Others
Front
1. MENU
6. PIP
2. Navigate button (Up-Down button)
7. Power button
3. Adjust button (Left-Right button)/
Volume button
8. Power indicator
4. ENTER
9. Remote Control Sensor
5. SOURCE
1. MENU
Use this button to open the on-screen menu and exit from the menu screen or close screen
adjustment menu.
2. Navigate buttons (Up-Down button)
Moves from one menu item to another vertically or adjusts selected menu values.
3. Adjust buttons (Left-Right button) / Volume buttons
Moves from one menu item to another horizontally or adjusts selected menu values.
Adjusts the audio volume.
4. ENTER
Activates a highlighted menu item.
5. SOURCE
Switches from PC mode to Video mode.
Changing the source is allowed only in external devices that are connected to the monitor
at the time.
To switch Screen modes:
[PC]
[BNC]
[DVI]
[AV]
[S-VIDEO]
[Component]
>>Click here to see an animation clip
6. PIP
Push the PIP button to turn PIP screen On/Off.
More than one PIP couldn't be overlapped on screen as BNC and the component use the
same terminal.
>>Click here to see an animation clip
• PC / DVI
: AV / S-Video / Component Mode
• BNC
: AV / S-Video Mode
• AV / S-Video
: PC / BNC / DVI Mode
• Component
: PC / DVI Mode
7. Power button
Use this button to turn the monitor on and off.
8. Power indicator
Power Indicator shows PowerSaver mode by green blinking.
9. Remote Control Sensor
Aim the remote control towards this spot on the Monitor.
See PowerSaver described in the manual for further information regarding power saving functions.
For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended
for long periods.
Rear
For detailed information concerning cable connections, refer to Connecting Cables under Setup.
The monitor's rear configuration may vary slightly depending on the monitor model.
1.
POWER SW : Switch the monitor on and off.
2.
POWER IN : Power cord, plug into monitor
and wall receptacle.
3.
RS232C OUT/IN (RS232C Serial PORT): MDC(Multiple Display Control) Program Port
4.
DVI IN(HDCP) (PC Video Connection Terminal)
: Using DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC)
5.
PC IN(RGB) (PC Video Connection Terminal)
: Using D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC)
6.
PC/DVI/BNC AUDIO IN (PC/DVI/BNC Audio Connection Terminal (Input))
7.
COMPONENT AUDIO IN [L-AUDIO-R](Component Audio Connection Terminal
(Input))
8.
BNC/COMPONENT OUT (BNC/Component Connection Terminal (Output))
- BNC (Analog PC) Connection : connecting R, G, B, H, V port
- Component Connection : connecting PR, Y, PBport
9.
BNC/COMPONENT IN (BNC/Component Connection Terminal (Input))
10. AV AUDIO IN [L-AUDIO-R](Monitor Audio Connection Terminal (Input))
11. AV OUT [VIDEO](VIDEO Connection Terminal) : AV mode (Output)
12. AV IN [VIDEO](VIDEO Connection Terminal) (Input)
13. AV OUT [S-VIDEO](S-Video Connection Terminal) : S-Video mode (Output)
14. AV IN [S-VIDEO](S-Video Connection Terminal) (Input)
15. EXT SPEAKER(8 Ω) (EXT Speaker Connection Terminal)
16. MONITOR OUT [L-AUDIO-R](Monitor Audio Connection Terminal (Output))
- MONITOR OUT is the terminal for sound output of PC, DVI or BNC.
The number of monitors that can be connected to loopout may be different
under the circumstance such as cable, signal source, etc.
With a cable which there is no degradation or signal source ten monitors can be
connected.
17. Kensington Lock
The Kensington lock is a device used to
physically fix the system when using it in a
public place.
(The locking device has to be purchased
separately. )
For using a locking device, contact where
you purchase it.
See Connecting the Monitor for further information regarding cable connections.
Remote Control
The performance of the remote control may be affected by a TV or other electronic devices operated
near the monitor, causing malfunction due to interference with frequency.
1. ON / OFF
2. MAGICNET
3. MDC
4. LOCK
5. MagicNet buttons
6. +100
7. VOL
8. MUTE
9. AUTO
10. MENU
11. ENTER
12. PRE-CH
13. CH/PAGE
14. SOURCE
15. INFO
16. EXIT
17. Up-Down Left-Right buttons
18. P.MODE (M/B)
19. STILL
20. BBE
21. MTS
22. PIP
23. SOURCE
24. SIZE
25. SWAP
26.
27.
28.
29.
1. ON / OFF
Use these buttons to turn the monitor on or off.
2. MAGICNET
MagicNet Quick Launch Button.
- This fuction does not work for this monitor.
3. MDC
MDC Quick Launch Button.
4. LOCK
This button will activate or deactivate all function keys on both the remote control and the monitor
except for the Power and LOCK buttons.
5. MagicNet buttons
- Used for MagicNet.
z
z
z
z
Alphanumeric: Used to enter the Internet address.
DEL : Functions as the backspace.
SYMBOL : Used to enter the symbols. (.O_-:/)
ENTER : Used to enter values.
- This fuction does not work for this monitor.
6. +100
Press to select channels over 100.
For example, to select channel 121, press "+100", then press "2" and "1".
- This fuction does not work for this monitor.
7. VOL
Adjusts the audio volume.
>>Click here to see an animation clip
8. MUTE
Pauses (mutes) the audio output temporarily.
Displayed on the lower left corner of the screen.
The audio resumes if MUTE or - VOL + is pressed in the Mute mode.
9. AUTO
Adjusts the screen display automatically.
If you change resolution in the control panel, auto function will be executed.
10. MENU
Use this button to open the on-screen menu and exit from the menu screen or close screen
adjustment menu.
11. ENTER
Activate a highlighted menu item.
12. PRE-CH
This button is used to return to the immediately previous channel.
- This fuction does not work for this monitor.
13. CH/PAGE
Selects channels or page.
- This fuction does not work for this monitor.
14. SOURCE
Push this button to change video sources.
15. INFO
Current picture information displays on the upper left corner of the screen.
16. EXIT
Exits from the menu screen.
17. Up-Down Left-Right buttons
Moves from one menu item to another horizontally, vertically or adjusts selected menu values.
18. P.MODE (M/B)
When you press this button, current picture mode is displayed on the lower center of the screen.
AV / S-Video / Component : P.MODE
The Monitor has four automatic picture settings that are preset at the factory.
Then push button again to circle through available preconfigured modes.
( Dynamic
Standard
Movie
Custom )
PC/DVI/BNC : M/B (MagicBright™)
MagicBright™ is a new feature providing the optimum viewing environment depending on the
contents of the image you are watching.
Then push button again to circle through available preconfigured modes.
(Entertain
Internet
Text
Custom )
19. STILL
When you press this button, STILL is displayed on the lower center of the screen.
Press the button once to freeze the screen.
Press it again to unfreeze.
20. BBE
Recreates the natural sound and improves sound clarity through boosting high and low range
frequencies. As a result high sounds are clearer, brilliant and finely detailed while low sounds are
tight, well-defined and harmonically rich.
21. MTS
You can select the MTS (Multichannel Television Stereo) mode.
FM Stereo
Audio Type
MTS/S_Mode
Mono
Mono
Stereo
SAP
Mono
Stereo
Mono
SAP
Default
Manual Change
Mono
- This fuction does not work for this monitor.
22. PIP
Every time you push the button, a PIP screen appears.
23. SOURCE
The PIP window's signal source changes.
24. SIZE
You can switch the Picture Size.
25. SWAP
Swapping the contents of the PIP and main image.
The image in the PIP window will appear on the main screen, and the main screen image will
appear in the PIP window.
26.
Rewind
27.
Stop
28.
Play/Pause
29.
Fast forward
Mechanical Lay-out | Monitor Head | Stand | Speaker | Installation VESA Bracket | Wall Bracket Installation
1. Mechanical Lay-out
2. Monitor Head
3. Stand
4. Speaker
5. Installation VESA Bracket
z
z
z
z
When installing VESA, make sure to comply with the international VESA standards.
Purchasing VESA Bracket and Installation Information : Please contact your nearest Samsung Distributor to place
an order. After your order is placed, installation professionals will visit you and install the bracket.
At least 2 persons are needed in order to move the LCD Monitor.
Samsung is not responsible for any product damage or any injury caused by installation at customer's discretion.
Dimensions
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
6. Wall Bracket Installation
z
z
z
Contact a technician for installing the wall bracket.
Samsung Electronics is not responsible for any damages to the product or harm to customers when the
installation is done by the customer.
This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
Components
Only use the components and accessories shipped with the product.
`
Wall Bracket
(1)
Hinge
(Left 1, Right 1)
Plastic Hanger Screw(A)
(4)
(11)
Screw(B)
(4)
Anchor
(11)
Wall Bracket Assembly
Insert and tighten the Captive Screw in the
direction of the arrow.
When done, mount the wall bracket on the wall.
A. Captive Screw
B. Wall Bracket
C. Hinge (Left)
D. Hinge (Right)
There are two hinges(left and right). Use the correct one.
Before drilling into the wall, check if the length
between the two locking holes at the back of the
product is correct.
If the length is too short or long, loosen all or
some of the 4screws on the wall bracket to adjust
the length.
A. Length between the two locking holes
Check the installation diagram and mark the drill
points on the wall. Use the 5.0 mm bit to drill
holes deeper than 35 mm. Fix each anchor in the
corresponding hole.
Match each of the brackets and hinge holes to
the corresponding anchor holes and insert and
tighten the 11 screws A.
To mount the product on the wall bracket
The shape of the product may vary depending on the model. (The assemblies of the plastic hanger and the
screw are the same)
Remove the 4 screws on the back of the
product.
Insert the screw B into the plastic hanger.
1. Mount the product on the wall bracket and
make sure it is properly fixed to the left and
right plastic hangers.
2. Be careful when installing the product on the
bracket as fingers can be caught in the holes.
3. Make sure the wall bracket is securely fixed to
the wall, or the product may not stay in place
after installation.
Tighten the 4 screws in step 2 (plastic hanger +
screw B)to the rear holes of the product.
Remove safety pin (3) and insert the 4 product
holders into the corresponding bracket holes (1).
Then place the product(2) so that it is firmly fixed
to the bracket. Make sure to re-insert and tighten
the safety pin (3) to securely hold the product to
the bracket.
A. Monitor
B. Wall Bracket
C. Wall
Wall Bracket Angle Adjustment
Adjust the bracket angle to -2°before installing it on the wall.
1. Fix the product to the wall bracket.
2. Hold the product at the top in the center and pull it forward
(direction of the arrow) to adjust the angle.
3. You can adjust the bracket angle between -2°and 15 °.
Make sure to use the top center, and not the
leftor the right side of the product to adjust the
angle.
SyncMaster 460Pn
Installing Stand Kit
Only the supplied bolts should be used.
Samsung Electronics will not be responsible for damages caused by using a base other than those
specified.
1. Installing the Semi Stand
Left stand
Right stand
Make sure to install the stand with
Caution label folded backward.
1. A 'Cover-Protector' is used to protect the hole at the bottom of the monitor, where the stand is
inserted. Be sure to remove the 'Cover-Protector' when attaching the provided Semi Stand or stand
kit (sold separately) and cover the hole using the 'Cover-Hole' when attaching the wall mount kit.
2. Set up the left and right stands respectively.
3. Put the stand into the hole at the bottom of the monitor.
Insert screw into the hole indicated and tighten. (M4 × L15)
This stand is originally designed for the adjustment of the screen angle. And the company is not
responsible for any problem caused by any use of this stand. Do never use the product as a
stand on which something is placed.
2. Installing Stand Kit (sold separately)
1. A 'Cover-Protector' is used to protect the hole at the bottom of the monitor, where the stand is
inserted. Be sure to remove the 'Cover-Protector' when attaching the provided Semi Stand or stand
kit (sold separately) and cover the hole using the 'Cover-Hole' when attaching the wall mount kit.
2. Make sure you put the parts in the right direction and in the right place. (M4 × L15)
3. Put the stand into the hole at the bottom of the monitor.
4. Insert screw into the hole indicated and tighten. (M4 × L15)
In case of Power cord with Earth
In the event of failure, earth lead may cause electric shock. Make sure to wire
the earth lead in an approprite manner, before plug-in the AC power. Or,
when un-wire the earth lead, make sure to plug-off the AC power in advance.
AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to
the monitor. For detailed information on connecting AV input devices, refer to User Controls under
Adjusting Your Monitor.
Connecting to a Computer | Connecting to a VCR | Connecting to a DVD Player | Connecting a Camcorder
Connecting DTV Set Top Box | Connecting Speakers | Connecting to an Audio System
Connecting the LAN Cable | Connecting USB | Connecting the Digital Audio System
1. Connecting to a Computer
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Trun on power switch.
2. There are 3 ways to connect the signal cable to your monitor.
Choose one of the followings :
2-1. Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, RGB port on the back of your monitor.
2-2. Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI(HDCP) port on the back of your monitor.
2-3. Using the BNC (Analog) connector on the video card.
Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V port on the back of your
Monitor and the 15 pin D-sub Port on the computer.
DVI cable or BNC cable is optional.
3. Connect the audio cable for your monitor to the audio port on the back of your computer.
4. Turn on both your computer and the monitor.
Contact a local Samsung Electronics Service Center to buy optional items.
2. Connecting to a VCR
1. AV input devices like VCRs or Camcorders are connected to the AV IN [VIDEO] or AV IN [S-VIDEO]
of the monitor using the S-VHS or BNC cable.
S-VHS or BNC cable is optional.
2. Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the monitor's AV AUDIO
IN [L-AUDIO-R] using audio cables.
3. Select AV or S-Video that is connected to a VCR or Camcorders using the Source button on the
monitor's front or remote control.
4. Then, start the VCR or Camcorders with a tape inserted.
3. Connecting to a DVD Player
1. Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor
and the AUDIO OUT jacks on the DVD player.
2. Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the Monitor and
the PR, Y, PB jacks on the DVD player.
Component cable is optional.
3. Select Component that is connected to a DVD player using the Source button on the monitor's front
or remote control.
4. Then, start the DVD Player with a DVD disc inserted.
For an explanation of Component video, see your DVD player owner's manual.
4. Connecting a Camcorder
1. Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the
camcorder.
Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the
COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor.
2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO]
on the Monitor.
3. Select AV that is connected to a Camcorder using the Source button on the monitor's front or
remote control.
4. Then, start the Camcorders with a tape inserted.
The audio-video cables shown here are usually included with a Camcorder.
(If not, check your local electronics store.)
If your camcorder is stereo, you need to connect a set of two cables.
5. Connecting DTV Set Top Box
The connections for a typical Set Top Box are shown below.
1. Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor
and the AUDIO OUT jacks on the Set Top Box.
2. Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the Monitor
and the PR, Y, PB jacks on the Set Top Box.
3. Select Component that is connected to a DTV Set Top Box using the Source button on the
monitor's front or remote control.
For an explanation of Component video, see your Set Top Box owner's manual.
6. Connecting Speakers
1. Tighten the SET and the speaker using the screws.
* Mount the set of the speaker without the speaker stand.
2. Connect the speaker connection cable between the speaker connection jack on the rear of the SET
and the speaker connection jack on the rear of the speaker.
Do not move the SET holding the speaker when the SET is connected to the speaker.
The speaker-bracket for connecting the SET speaker my be damaged.
7. Connecting to an Audio System
1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and the
MONITOR OUT [L-AUDIO-R] on the Monitor.
8. Connecting the LAN Cable
1. Connect the LAN cable.
9. Connecting USB
1. You can connect to USB devices such as a mouse or keyboard.
10. Connecting the Digital Audio System
1. Connect a set of digital audio cables between the Digital Audio Input jacks on the DIGTAL AUDIO
SYSTEM and the DIGITAL AUDIO OUT on the Monitor.
1. Introduction
2. Beginning :
Main Screen | Port Setting |
3. Power Control
4. Input Source Control
5. Image Size Control :
PC, BNC, DVI |
AV, S-Video, Component, DVI(HDCP)
1. Introduction
6. Time Control
7. PIP Control :
PIP Size | PIP Source
8. Settings Control :
Picture | Picture PC | Audio | Image Lock |
9. Maintenance Control - Lamp Control
10. Maintenance Control - Scroll
11. Maintenance Control - Video Wall
12. Troubleshooting
13. Settings Value Display In Multiple Display Mode
A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously
operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a
PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the
serial port on a display.
2. Main Screen
Click Start > Program > Multiple Display Control to start the program.
Select a set to see the volume of the selected set within the slider.
Main Icons
Select Button
Remocon
Info Grid
Safety Lock
Display Selection
Port Selection
Control Tools
1. Use the main icons to switch into each screen.
2. Allows you to enable or disable the remote control signal receiving function of the display unit.
3. The setting for the PC Serial Port can change. The original value is COM1.
4. Sets the Lock Function.
5. Click Select all or Clear to select or clear all displays.
6. Use Grid to view brief information on selected display.
7. Select a display from Display Selection.
8. Use Control Tools to control displays.
The remote control Enable/Disable function operates whether or not the power is On/Off, and
this applies to all displays connected to the displays connected to the MDC However,
regardless of the status at the time the MDC is shut down, the remote control signal receiving
function of all displays is initialized to Enable when the MDC is closed.
2. Beginning - Port Setting
1. Multiple Display Control is originally set to COM1.
2. If any port other than COM1 is used, COM1 to COM4 can be selected in Port Selection Menu.
3. If the exact port name which is connected to the monitor using a serial cable is not selected,
communication will not be unavailable.
4. The selected port is stored in the program and used for the next program as well.
3. Power Control
1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control.
1) Power Status
2) Input Source
3) Image Size
4) On Timer Status
5) Off Timer Status
2. Use the Select All button or Check Box to choose a display to control.
Power Control allows controlling some of the functions of the selected display.
1) Power On/Off
- Turns the power of the selected display On/Off.
2) Volume Control
- Controls the volume level of the selected display.
It receives the volume value of the selected display from the sets and displays it in the slider.
(When you cancel the selection or choose Select All, the value returns to the default value 10)
3) Mute On/Off
- Enables/disables the Mute function of the selected display.
When selecting one set at a time, enable Mute when the Mute function is enabled for the selected set.
The Mute function is disabled automatically when you adjust the volume level.
(The values return to the default settings when you undo the selections or choose "Select All.")
The Power Control feature is available for all displays.
The Volume Control and Mute features are available only for the displays whose power status is
ON.
4. Input Source Control
1. Click Input Source of the main icons and the Input Source control screen appears.
Click Select All or use Check Box to select a display to control.
Info Grid shows some basic information necessary to Input Source Control.
1) PC
- Changes the Input Source of the selected display to PC.
2) BNC
- Changes the Input Source of the selected display to BNC.
3) DVI
- Changes the Input Source of the selected display to DVI.
4) AV
- Changes the Input Source of the selected display to AV.
5) S-Video
- Changes the Input Source of the selected display to S-Video.
6) Component
- Changes the Input Source of the selected display to Component.
7) MagicNet
- The Input source of MagicNet works only on MagicNet model.
The Input Source Control feature is available only for the displays whose power status is ON.
5. Image Size Control - PC, BNC, DVI
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1) Power
- Shows the power status of the current display.
2) Image Size
- Shows the current Image Size of the display in use.
3) Input Source
- Shows the current Input Source of the display in use.
4) Info Grid displays only the displays whose Input Source is PC,BNC,DVI .
5) When you click Image Size, the PC, BNC, DVI tabs first appear.
- The Image Size Control button controls Image Size available for PC,BNC,DVI.
6) Click the AV, S-Video, Component tab to control Image Size for respective Input Source.
Image Size Control is available only for the displays for which power status is ON.
The Input source of MagicNet works only on MagicNet model.
5. Image Size Control - AV, S-Video, Component, DVI(HDCP)
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1) Click the AV, S-Video, Component tab to adjust Image Size for AV, S-Video, Component.
Click Select All or use Check Box to select a display to control.
2) Info Grid displays only the display having AV, S-Video, Component or DVI(HDCP) as input source.
3) Switch Image Size of the selected display randomly.
Panorama, Zoom1 and Zoom2 are not available for selection when the input signal type for
Component and DVI (HDCP) is 720p or 1080i.
The Image Size Control feature is available only for the displays whose power status is ON.
The Input source of MagicNet works only on MagicNet model.
6. Time Control
1. Click Time of the main icons and the Time Control screen appears.
Info Grid shows some basic information necessary to Time Control.
1) Current Time
- Set the current time for the selected display (PC Time).
- To change the current time, first change the PC Time.
2) On Time Setup
- Set the hour, minute, AM/PM of On Time, Status, Source, volume of the selected display.
3) Off Time Setup
- Set the hour, minute, and AM/PM, Status for Off Timer of the selected display.
4) Shows the On Timer settings.
5) Shows the Off Timer settings.
Time Control is available only for the displays for which the power status is ON.
The Input source of MagicNet works only on MagicNet model.
7. PIP Control - PIP Size
1. Click PIP of the main icons and the PIP control screen appears.
Click Select All or use Check Box to select a display to control.
Info Grid shows some basic information necessary to PIP Size Control.
1) PIP Size
- Shows the current PIP Size of the display in use.
2) OFF
- Turns off the PIP of the selected display.
3) Large
- Turns on the PIP of the selected display and changes the size to Large.
4) Small
- Turns on the PIP of the selected display and changes the size to Small.
5) Double1
- Turns on the PIP of the selected display and changes the size to Double 1.
6) Double2
- Turns on the PIP of the selected display and changes the size to Double 2.
7) Double3 (Picture By Picture)
- Turns on the PIP of the selected display and changes the size to Double 3.
PIP Size can be controlled with turning on the monitor power.
The Input source of MagicNet works only on MagicNet model.
7. PIP Control - PIP Source
1. Click PIP of the main icons and the PIP control screen appears.
Info Grid shows some basic information necessary to PIP Source Control.
1) PIP Source
- PIP Source can be controlled with turning on the monitor power.
2) PC
- Changes the source of the PIP of the selected display to PC.
3) BNC
- Changes the source of the PIP of the selected display to BNC.
4) DVI
- Changes the source of the PIP of the selected display to DVI.
5) AV
- Changes the source of the PIP of the selected display to AV.
6) S-Video
- Changes the source of the PIP of the selected display to S-Video.
7) Component
- Changes the source of the PIP of the selected display to Component.
Some of the PIP Sources may not be available for selection depending on the input source
type of the Main Screen.
The PIP Control feature is available only for the displays whose power status is ON and the PIP
function is set to ON.
The Input source of MagicNet works only on MagicNet model.
8. Settings Control - Picture
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
When each function is selected, the set value of the selected function is displayed in the slide.
When Select All is selected, the default value (50) returns.
Changing a value in this screen will automatically change the mode to "CUSTOM."
1) Picture
- Available only for AV, S-Video, Component, DVI(HDCP).
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness of the selected display.
4) Sharpness
- Adjusts Sharpness of the selected display.
5) Color
- Adjusts Color of the selected display.
6) Tint
- Adjusts Tint of the selected display.
7) Color Tone
- Adjusts Color Tone of the selected display.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed.
The Input source of MagicNet works only on MagicNet model.
8. Settings Control - Picture PC
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the
set value of the selected function is displayed in the slide.
When Select All is selected, the default value (50) returns.
Changing a value in this screen will automatically change the mode to "CUSTOM."
1) Picture PC
- Available only for PC, BNC, DVI.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness of the selected display.
4) Red
- Adjusts red Color of the selected display.
5) Green
- Adjusts green Color of the selected display.
6) Blue
- Adjusts blue Color of the selected display.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed.
The Input source of MagicNet works only on MagicNet model.
8. Settings Control - Audio
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the
set value of the selected function is displayed in the slide.
When Select All is selected, the default value (50) returns.
Changing a value in this screen will automatically change the mode to "CUSTOM."
1) Audio
- Controls audio settings for all input sources.
2) Bass
- Adjusts Bass of the selected display.
3) Treble
- Adjusts Treble of the selected display.
4) Balance
- Adjusts Balance of the selected display.
5) Dolby Virtual
- Dolby Virtual Sound On/Off of the selected display.
6) BBE
- BBE Sound On/Off of the selected display.
7) Sound Select
- Select either Main or Sub when PIP is On.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed.
The Input source of MagicNet works only on MagicNet model.
8. Settings Control - Image Lock
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
1) Image Lock
- Available only for PC, BNC.
2) Coarse
- Adjusts Coarse of the selected display.
3) Fine
- Adjusts Fine of the selected display.
4) Position
- Adjusts Position of the selected display.
5) Auto Adjustment
- Self-Adjust to the incoming PC signal.
Settings Control is available only for the displays for which the power status is ON.
The Input source of MagicNet works only on MagicNet model.
9. Maintenance Control - Lamp Control
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
An "Info Grid" showing several basic data items appears.
1) Maintenance
- Allows Maintenance Control for all input sources.
2) Auto Lamp Control
Automatically adjusts the backlight of the selected display at a specified time.
The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
3) Manual Lamp Control
- Allows you to adjust the backlight of the selected display regardless of the time.
The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control function.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicNet works only on MagicNet model.
10. Maintenance Control - Scroll
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Screen Scroll
Eliminates the afterimages that can result when the selected display stays in Pause mode for an
- extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and
"Second" by second.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicNet works only on MagicNet model.
11. Maintenance Control - Video Wall
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Video Wall
- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of
the whole picture or so that the same picture is repeated on each screen.
2) Screen Divider
- The screen can be divided into.
You can select a number of screens with a different layout when dividing.
Select a mode from Screen Divider.
Select a display from Display Selection.
The place will be set up by pressing a number in the selected mode..
z
z
z
z
2*2
z
3*3
z
1*5
z
5*1
3) On / Off
- Turns on/off the Video Wall function of the selected display.
4) Format
- The format can be selected to see a divided screen.
z
Full
z
Natural
The Maintenance Control function is available only for the displays where the power status is ON.
The Input source of MagicNet works only on MagicNet model.
12. Troubleshooting
1. The display you wish to control does not appear on the Power Control Info Grid
- Check the connection of RS232C. (Check if it is properly connected to the Com1 port)
- Check the displays to see if any of the other displays connected have the same ID. If more than one
displays have the same ID, those displays are not properly detected by the program due to data conflict.
- Check if the Display Set ID is a number between 1 and 10. (Adjust using the Display menu)
A Display Set ID must be a value between 1 and 10.
If the value is out of the range, the MDC system cannot control the display.
2. The display you wish to control does not appear on the other Control Info Grids
- Check to see if the display power is ON. (You can check this in Power Control Info Grid)
- Check if you can change the input source of the display.
3. The dialogue box appears repeatedly.
- Check to see if the display you wish to control is selected.
4. Both On Timer and Off Timer have been set but different time is showing.
- Apply current time to synchronize the display clocks.
5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C
cable, or exit the program in an Irregular manner. Rerun the program and turn the remote function again to
Restore normal functions.
This program may malfunction due to problems in communication circuits or interference from
electronic appliances nearby.
13. Settings Value Display In Multiple Display Mode
When there are more than one displays connected, the settings values are displayed as follows.
1. No selection: Displays the Factory Default Value.
2. Selected one display: Fetches and displays the settings value for the selected display.
3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings
value of ID 1, fetches and displays the value of ID3.
4. Selected all sets using Select All: Returns to the Factory Default Value.
Natural Color
Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer
or other images scanned by a scanner or a digital camera are not the same as those shown on the
monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system
developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI).
This system is available only for Samsung monitors and makes the color of the images on the monitor
the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the
program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural
Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM
Drive, click the [Start] button of Windows and then select [Execute].
Enter D:\color\eng\setup.exe and then press the <Enter> key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select "Setting" / 'Control Panel" on the "Start" menu and then double-click "Add/Delete a
program".
Select Natural Color from the list and then click the [Add/Delete] button.
Installation
1. Insert the installation CD into the CD-ROM drive.
2. Click the MagicNet installation file.
3. When the InstallShield Wizard window appears, click "Next."
4. Select "I agree to the terms of the license agreement" to accept the terms of use.
5. You are required to log in to the MagicNet Server program. Please enter the password to login. The
password cannot be changed when you are logged in.
6. Choose a folder to install the MagicNet program.
7. Click "Install."
8. The "Installation Status" window appears.
9. It is recommended restarting the system for the normal operation of the MagicNet Server program.
Click "Finish."
10. When the installation is complete, the MagicNet executable icon appears on your desktop.
11. Double-click the icon to start the program.
System Requirements
CPU
RAM
Minimum
P1.8
256M
Recommended
P3.0Ghz
512M
Ethernet
OS
Application
Windows XP
100M
Windows 2000
(Service Pack 4)
WMP 9 or later
SyncMaster 460P
Installing Stand Kit
Only the supplied bolts should be used.
Samsung Electronics will not be responsible for damages caused by using a base other than those
specified.
1. Installing the Semi Stand
Left stand
Right stand
Make sure to install the stand with
Caution label folded backward.
1. A 'Cover-Protector' is used to protect the hole at the bottom of the monitor, where the stand is
inserted. Be sure to remove the 'Cover-Protector' when attaching the provided Semi Stand or stand
kit (sold separately) and cover the hole using the 'Cover-Hole' when attaching the wall mount kit.
2. Set up the left and right stands respectively.
3. Put the stand into the hole at the bottom of the monitor.
Insert screw into the hole indicated and tighten. (M4 × L15)
This stand is originally designed for the adjustment of the screen angle. And the company is not
responsible for any problem caused by any use of this stand. Do never use the product as a
stand on which something is placed.
2. Installing Stand Kit (sold separately)
1. A 'Cover-Protector' is used to protect the hole at the bottom of the monitor, where the stand is
inserted. Be sure to remove the 'Cover-Protector' when attaching the provided Semi Stand or stand
kit (sold separately) and cover the hole using the 'Cover-Hole' when attaching the wall mount kit.
2. Make sure you put the parts in the right direction and in the right place. (M4 × L15)
3. Put the stand into the hole at the bottom of the monitor.
4. Insert screw into the hole indicated and tighten. (M4 × L15)
In case of Power cord with Earth
In the event of failure, earth lead may cause electric shock. Make sure to wire
the earth lead in an approprite manner, before plug-in the AC power. Or,
when un-wire the earth lead, make sure to plug-off the AC power in advance.
AV input devices like DVDs, VCRs or Camcorders as well as your computer may be connected to
the monitor. For detailed information on connecting AV input devices, refer to User Controls under
Adjusting Your Monitor.
Connecting to a Computer | Connecting to a VCR | Connecting to a DVD Player | Connecting a Camcorder
Connecting DTV Set Top Box | Connecting Speakers | Connecting to an Audio System
1. Connecting to a Computer
1. Connect the power cord for your monitor to the power port on the back of the monitor.
Trun on power switch.
2. There are 3 ways to connect the signal cable to your monitor.
Choose one of the followings :
2-1. Using the D-sub (Analog) connector on the video card.
Connect the signal cable to the 15-pin, RGB port on the back of your monitor.
2-2. Using the DVI (Digital) connector on the video card.
Connect the DVI Cable to the DVI(HDCP) port on the back of your monitor.
2-3. Using the BNC (Analog) connector on the video card.
Connect the BNC Cable to the BNC/COMPONENT IN - R, G, B, H, V port on the back of your
Monitor and the 15 pin D-sub Port on the computer.
DVI cable or BNC cable is optional.
3. Connect the audio cable for your monitor to the audio port on the back of your computer.
4. Turn on both your computer and the monitor.
Contact a local Samsung Electronics Service Center to buy optional items.
2. Connecting to a VCR
1. AV input devices like VCRs or Camcorders are connected to the AV IN [VIDEO] or AV IN [S-VIDEO]
of the monitor using the S-VHS or BNC cable.
S-VHS or BNC cable is optional.
2. Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the monitor's AV AUDIO
IN [L-AUDIO-R] using audio cables.
3. Select AV or S-Video that is connected to a VCR or Camcorders using the Source button on the
monitor's front or remote control.
4. Then, start the VCR or Camcorders with a tape inserted.
3. Connecting to a DVD Player
1. Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor
and the AUDIO OUT jacks on the DVD player.
2. Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the Monitor and
the PR, Y, PB jacks on the DVD player.
Component cable is optional.
3. Select Component that is connected to a DVD player using the Source button on the monitor's front
or remote control.
4. Then, start the DVD Player with a DVD disc inserted.
For an explanation of Component video, see your DVD player owner's manual.
4. Connecting a Camcorder
1. Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the
camcorder.
Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the
COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor.
2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO]
on the Monitor.
3. Select AV that is connected to a Camcorder using the Source button on the monitor's front or
remote control.
4. Then, start the Camcorders with a tape inserted.
The audio-video cables shown here are usually included with a Camcorder.
(If not, check your local electronics store.)
If your camcorder is stereo, you need to connect a set of two cables.
5. Connecting DTV Set Top Box
The connections for a typical Set Top Box are shown below.
1. Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the Monitor
and the AUDIO OUT jacks on the Set Top Box.
2. Connect a Component cable between the BNC/COMPONENT IN - PR, Y, PB port on the Monitor
and the PR, Y, PB jacks on the Set Top Box.
3. Select Component that is connected to a DTV Set Top Box using the Source button on the
monitor's front or remote control.
For an explanation of Component video, see your Set Top Box owner's manual.
6. Connecting Speakers
1. Tighten the SET and the speaker using the screws.
* Mount the set of the speaker without the speaker stand.
2. Connect the speaker connection cable between the speaker connection jack on the rear of the SET
and the speaker connection jack on the rear of the speaker.
Do not move the SET holding the speaker when the SET is connected to the speaker.
The speaker-bracket for connecting the SET speaker my be damaged.
7. Connecting to an Audio System
1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and the
MONITOR OUT [L-AUDIO-R] on the Monitor.
1. Introduction
2. Beginning :
Main Screen | Port Setting |
3. Power Control
4. Input Source Control
5. Image Size Control :
PC, BNC, DVI |
AV, S-Video, Component, DVI(HDCP)
1. Introduction
6. Time Control
7. PIP Control :
PIP Size | PIP Source
8. Settings Control :
Picture | Picture PC | Audio | Image Lock |
9. Maintenance Control - Lamp Control
10. Maintenance Control - Scroll
11. Maintenance Control - Video Wall
12. Troubleshooting
13. Settings Value Display In Multiple Display Mode
A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously
operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a
PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the
serial port on a display.
2. Main Screen
Click Start > Program > Multiple Display Control to start the program.
Select a set to see the volume of the selected set within the slider.
Main Icons
Select Button
Remocon
Info Grid
Safety Lock
Display Selection
Port Selection
Control Tools
1. Use the main icons to switch into each screen.
2. Allows you to enable or disable the remote control signal receiving function of the display unit.
3. The setting for the PC Serial Port can change. The original value is COM1.
4. Sets the Lock Function.
5. Click Select all or Clear to select or clear all displays.
6. Use Grid to view brief information on selected display.
7. Select a display from Display Selection.
8. Use Control Tools to control displays.
The remote control Enable/Disable function operates whether or not the power is On/Off, and
this applies to all displays connected to the displays connected to the MDC However,
regardless of the status at the time the MDC is shut down, the remote control signal receiving
function of all displays is initialized to Enable when the MDC is closed.
2. Beginning - Port Setting
1. Multiple Display Control is originally set to COM1.
2. If any port other than COM1 is used, COM1 to COM4 can be selected in Port Selection Menu.
3. If the exact port name which is connected to the monitor using a serial cable is not selected,
communication will not be unavailable.
4. The selected port is stored in the program and used for the next program as well.
3. Power Control
1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control.
1) Power Status
2) Input Source
3) Image Size
4) On Timer Status
5) Off Timer Status
2. Use the Select All button or Check Box to choose a display to control.
Power Control allows controlling some of the functions of the selected display.
1) Power On/Off
- Turns the power of the selected display On/Off.
2) Volume Control
- Controls the volume level of the selected display.
It receives the volume value of the selected display from the sets and displays it in the slider.
(When you cancel the selection or choose Select All, the value returns to the default value 10)
3) Mute On/Off
- Enables/disables the Mute function of the selected display.
When selecting one set at a time, enable Mute when the Mute function is enabled for the selected set.
The Mute function is disabled automatically when you adjust the volume level.
(The values return to the default settings when you undo the selections or choose "Select All.")
The Power Control feature is available for all displays.
The Volume Control and Mute features are available only for the displays whose power status is
ON.
4. Input Source Control
1. Click Input Source of the main icons and the Input Source control screen appears.
Click Select All or use Check Box to select a display to control.
Info Grid shows some basic information necessary to Input Source Control.
1) PC
- Changes the Input Source of the selected display to PC.
2) BNC
- Changes the Input Source of the selected display to BNC.
3) DVI
- Changes the Input Source of the selected display to DVI.
4) AV
- Changes the Input Source of the selected display to AV.
5) S-Video
- Changes the Input Source of the selected display to S-Video.
6) Component
- Changes the Input Source of the selected display to Component.
7) MagicNet
- The Input source of MagicNet works only on MagicNet model.
The Input Source Control feature is available only for the displays whose power status is ON.
5. Image Size Control - PC, BNC, DVI
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1) Power
- Shows the power status of the current display.
2) Image Size
- Shows the current Image Size of the display in use.
3) Input Source
- Shows the current Input Source of the display in use.
4) Info Grid displays only the displays whose Input Source is PC,BNC,DVI .
5) When you click Image Size, the PC, BNC, DVI tabs first appear.
- The Image Size Control button controls Image Size available for PC,BNC,DVI.
6) Click the AV, S-Video, Component tab to control Image Size for respective Input Source.
Image Size Control is available only for the displays for which power status is ON.
The Input source of MagicNet works only on MagicNet model.
5. Image Size Control - AV, S-Video, Component, DVI(HDCP)
1. Click Image Size of the main icons and the Image Size control screen appears.
Info Grid shows some basic information necessary to Image Size Control.
1) Click the AV, S-Video, Component tab to adjust Image Size for AV, S-Video, Component.
Click Select All or use Check Box to select a display to control.
2) Info Grid displays only the display having AV, S-Video, Component or DVI(HDCP) as input source.
3) Switch Image Size of the selected display randomly.
Panorama, Zoom1 and Zoom2 are not available for selection when the input signal type for
Component and DVI (HDCP) is 720p or 1080i.
The Image Size Control feature is available only for the displays whose power status is ON.
The Input source of MagicNet works only on MagicNet model.
6. Time Control
1. Click Time of the main icons and the Time Control screen appears.
Info Grid shows some basic information necessary to Time Control.
1) Current Time
- Set the current time for the selected display (PC Time).
- To change the current time, first change the PC Time.
2) On Time Setup
- Set the hour, minute, AM/PM of On Time, Status, Source, volume of the selected display.
3) Off Time Setup
- Set the hour, minute, and AM/PM, Status for Off Timer of the selected display.
4) Shows the On Timer settings.
5) Shows the Off Timer settings.
Time Control is available only for the displays for which the power status is ON.
The Input source of MagicNet works only on MagicNet model.
7. PIP Control - PIP Size
1. Click PIP of the main icons and the PIP control screen appears.
Click Select All or use Check Box to select a display to control.
Info Grid shows some basic information necessary to PIP Size Control.
1) PIP Size
- Shows the current PIP Size of the display in use.
2) OFF
- Turns off the PIP of the selected display.
3) Large
- Turns on the PIP of the selected display and changes the size to Large.
4) Small
- Turns on the PIP of the selected display and changes the size to Small.
5) Double1
- Turns on the PIP of the selected display and changes the size to Double 1.
6) Double2
- Turns on the PIP of the selected display and changes the size to Double 2.
7) Double3 (Picture By Picture)
- Turns on the PIP of the selected display and changes the size to Double 3.
PIP Size can be controlled with turning on the monitor power.
The Input source of MagicNet works only on MagicNet model.
7. PIP Control - PIP Source
1. Click PIP of the main icons and the PIP control screen appears.
Info Grid shows some basic information necessary to PIP Source Control.
1) PIP Source
- PIP Source can be controlled with turning on the monitor power.
2) PC
- Changes the source of the PIP of the selected display to PC.
3) BNC
- Changes the source of the PIP of the selected display to BNC.
4) DVI
- Changes the source of the PIP of the selected display to DVI.
5) AV
- Changes the source of the PIP of the selected display to AV.
6) S-Video
- Changes the source of the PIP of the selected display to S-Video.
7) Component
- Changes the source of the PIP of the selected display to Component.
Some of the PIP Sources may not be available for selection depending on the input source
type of the Main Screen.
The PIP Control feature is available only for the displays whose power status is ON and the PIP
function is set to ON.
The Input source of MagicNet works only on MagicNet model.
8. Settings Control - Picture
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
When each function is selected, the set value of the selected function is displayed in the slide.
When Select All is selected, the default value (50) returns.
Changing a value in this screen will automatically change the mode to "CUSTOM."
1) Picture
- Available only for AV, S-Video, Component, DVI(HDCP).
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness of the selected display.
4) Sharpness
- Adjusts Sharpness of the selected display.
5) Color
- Adjusts Color of the selected display.
6) Tint
- Adjusts Tint of the selected display.
7) Color Tone
- Adjusts Color Tone of the selected display.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed.
The Input source of MagicNet works only on MagicNet model.
8. Settings Control - Picture PC
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the
set value of the selected function is displayed in the slide.
When Select All is selected, the default value (50) returns.
Changing a value in this screen will automatically change the mode to "CUSTOM."
1) Picture PC
- Available only for PC, BNC, DVI.
2) Contrast
- Adjusts Contrast of the selected display.
3) Brightness
- Adjusts Brightness of the selected display.
4) Red
- Adjusts red Color of the selected display.
5) Green
- Adjusts green Color of the selected display.
6) Blue
- Adjusts blue Color of the selected display.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed.
The Input source of MagicNet works only on MagicNet model.
8. Settings Control - Audio
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control. When each function is selected, the
set value of the selected function is displayed in the slide.
When Select All is selected, the default value (50) returns.
Changing a value in this screen will automatically change the mode to "CUSTOM."
1) Audio
- Controls audio settings for all input sources.
2) Bass
- Adjusts Bass of the selected display.
3) Treble
- Adjusts Treble of the selected display.
4) Balance
- Adjusts Balance of the selected display.
5) Dolby Virtual
- Dolby Virtual Sound On/Off of the selected display.
6) BBE
- BBE Sound On/Off of the selected display.
7) Sound Select
- Select either Main or Sub when PIP is On.
This feature is available only for the displays whose power status is ON and if no selection is
made, the factory default is displayed.
The Input source of MagicNet works only on MagicNet model.
8. Settings Control - Image Lock
1. Click Settings of the main icons and the Settings Control screen appears.
Info Grid shows some basic information necessary to Settings Control.
1) Image Lock
- Available only for PC, BNC.
2) Coarse
- Adjusts Coarse of the selected display.
3) Fine
- Adjusts Fine of the selected display.
4) Position
- Adjusts Position of the selected display.
5) Auto Adjustment
- Self-Adjust to the incoming PC signal.
Settings Control is available only for the displays for which the power status is ON.
The Input source of MagicNet works only on MagicNet model.
9. Maintenance Control - Lamp Control
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
An "Info Grid" showing several basic data items appears.
1) Maintenance
- Allows Maintenance Control for all input sources.
2) Auto Lamp Control
Automatically adjusts the backlight of the selected display at a specified time.
The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
3) Manual Lamp Control
- Allows you to adjust the backlight of the selected display regardless of the time.
The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control function.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicNet works only on MagicNet model.
10. Maintenance Control - Scroll
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Screen Scroll
Eliminates the afterimages that can result when the selected display stays in Pause mode for an
- extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and
"Second" by second.
The Maintenance Control feature is available only for the displays whose power status is ON.
The Input source of MagicNet works only on MagicNet model.
11. Maintenance Control - Video Wall
1. Click on the "Maintenance" icon in the Main Icon column to display the Maintenance screen.
1) Video Wall
- A Video Wall is a set of video screens that are connected together, so that each screen shows a part of
the whole picture or so that the same picture is repeated on each screen.
2) Screen Divider
- The screen can be divided into.
You can select a number of screens with a different layout when dividing.
Select a mode from Screen Divider.
Select a display from Display Selection.
The place will be set up by pressing a number in the selected mode..
z
z
z
z
2*2
z
3*3
z
1*5
z
5*1
3) On / Off
- Turns on/off the Video Wall function of the selected display.
4) Format
- The format can be selected to see a divided screen.
z
Full
z
Natural
The Maintenance Control function is available only for the displays where the power status is ON.
The Input source of MagicNet works only on MagicNet model.
12. Troubleshooting
1. The display you wish to control does not appear on the Power Control Info Grid
- Check the connection of RS232C. (Check if it is properly connected to the Com1 port)
- Check the displays to see if any of the other displays connected have the same ID. If more than one
displays have the same ID, those displays are not properly detected by the program due to data conflict.
- Check if the Display Set ID is a number between 1 and 10. (Adjust using the Display menu)
A Display Set ID must be a value between 1 and 10.
If the value is out of the range, the MDC system cannot control the display.
2. The display you wish to control does not appear on the other Control Info Grids
- Check to see if the display power is ON. (You can check this in Power Control Info Grid)
- Check if you can change the input source of the display.
3. The dialogue box appears repeatedly.
- Check to see if the display you wish to control is selected.
4. Both On Timer and Off Timer have been set but different time is showing.
- Apply current time to synchronize the display clocks.
5. The remote may not function properly when you turn off the remote Function, disconnect the RS-232C
cable, or exit the program in an Irregular manner. Rerun the program and turn the remote function again to
Restore normal functions.
This program may malfunction due to problems in communication circuits or interference from
electronic appliances nearby.
13. Settings Value Display In Multiple Display Mode
When there are more than one displays connected, the settings values are displayed as follows.
1. No selection: Displays the Factory Default Value.
2. Selected one display: Fetches and displays the settings value for the selected display.
3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings
value of ID 1, fetches and displays the value of ID3.
4. Selected all sets using Select All: Returns to the Factory Default Value.
Natural Color
Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer
or other images scanned by a scanner or a digital camera are not the same as those shown on the
monitor.
The Natural Color S/W is the very solution for this problem. It is a color administration system
developed by Samsung Electronics in association with Korea Electronics & Telecommunications
Research Institute (ETRI).
This system is available only for Samsung monitors and makes the color of the images on the monitor
the same as the printed or scanned images.
For more information, refer to Help (F1) in the software program.
How to install the Natural Color software
Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the
program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural
Color software.
To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM
Drive, click the [Start] button of Windows and then select [Execute].
Enter D:\color\eng\setup.exe and then press the <Enter> key.
(If the drive where the CD is inserted is not D:\, enter the applicable drive.)
How to delete the Natural Color software program
Select "Setting" / 'Control Panel" on the "Start" menu and then double-click "Add/Delete a
program".
Select Natural Color from the list and then click the [Add/Delete] button.
SyncMaster 460Pn
Input
Available Mode
OSD
Source List
: PC / BNC / DVI
: AV
: S-Video
: Component
Description
Use to select PC, BNC or other external input sources
connected to the Monitor.
Use to select the screen of your choice.
- The direct button on the remote control is 'SOURCE'
button.
The PIP turns off when the monitor is switched to
an external source.
1) PC
2) BNC
3) DVI
4) AV
5) S-Video
6) Component
7) MagicNet
PIP
When external A/V devices such as VCRs or DVDs are
connected to the monitor, PIP allows you to watch video from
: MagicNet
Play
those devices in a small window super-imposed on the PC
Video signal. (Off/On)
More than one PIP couldn't be overlapped on
screen as BNC and the component use the same
terminal.
1) PIP
- The direct button on the remote control is 'PIP' button.
Off
On
: Turn the PIP Screen on or off.
2) Source
- The direct button on the remote control is 'SOURCE'
button.
PC / DVI
: AV / S-Video / Component Mode
BNC
: AV / S-Video Mode
AV / S-Video
: PC / BNC / DVI Mode
Component
: PC / DVI Mode
: Select the input source for the PIP.
3) Swap
- The direct button on the remote control is 'SWAP' button.
: Swapping the contents of the PIP and main image.
The image in the PIP window will appear on the main
screen, and the main screen image will appear in the PIP
window.
4) Size
- The direct button on the remote control is 'SIZE' button.
: Change the Size of the PIP window.
If you select
,
,
in Size, Position and Transparency
will not be activated.
5) Position
: Change the Position of the PIP window.
6) Transparency
High
Medium
Low
Opaque
: Adjust the Transparency of PIP windows.
Available Mode : PIP
Edit Name
Name the input device connected to the input jacks to make
your input source selection easier.
MagicNet couldn't be renamed.
1) PC
2) BNC
3) DVI
4) AV
5) S-Video
6) Component
1) PIP
2) Source
3) Swap
4) Size
5) Position
6) Transparency
Picture
PC / BNC /DVI Mode
Available Mode
OSD
: PC / BNC / DVI
: AV
: S-Video
: Component
: MagicNet
Description
MagicBright™
MagicBright™ is a new feature providing the optimum
viewing environment depending on the contents of the image
you are watching.
Currently four different modes are available: Entertain,
Internet,Text and Custom.
Each mode has its own pre-configured brightness value. You
can easily select one of four settings by simply pressing the
MagicBright™ control button.
- The direct button on the remote control is 'M/B' button.
1) Entertain
: High brightness
For watching motion pictures such as a DVD or VCD.
2) Internet
: Medium brightness
For working with a mixture of images such as text and
graphics.
3) Text
: Normal brightness
For documentations or works involving heavy text.
4) Custom
Although the values are carefully chosen by our engineers,
the pre-configured values may not be comfortable to your
eyes depending on your taste.
If this is the case, adjust the brightness and contrast by
using the OSD menu.
Custom
You can use the on-screen menus to change the contrast
and brightness according to personal preference.
1) Contrast
: Adjust the Contrast.
2) Brightness
: Adjust the Brightness.
If you adjust picture using Custom function, MagicBright will turn to Custom mode.
Color Tone
The tone of the color can be changed.
1) Cool
2) Normal
3) Warm
Play
4) Custom
Color Control
Adjust the individual R, G, B color controls.
1) Red
2) Green
3) Blue
If you adjust picture using Color Control function, Color Tone will turn to Custom mode.
Image Lock
Image Lock is used to fine-tune and get the best image by
removing noise that creates unstable images with jitter and
shimmer. If satisfactory results are not obtained using the
Fine adjustment, use the Coarse adjustment and then use
Fine again.
1) Coarse
: Removes noise such as vertical stripes. Coarse adjustment
may move the screen image area. You may relocate it to the
center using the horizontal control menu.
2) Fine
: Removes noise such as horizontal stripes. If the noise
persists even after fine tuning, repeat it after adjusting the
frequency (clock speed).
3) Position
: Adjusts the screen location horizontally and vertically.
Auto
Adjustment
The values of Fine, Coarse, position are adjusted
automatically.
If you change resolution in the control panel, auto function
will be executed.
- The direct button on the remote control is 'AUTO'
button.
Signal
Balance
Used to make up for the weak RGB signal which has been
transmitted by a long signal cable.
1) Signal Balance
You can select with the signal control either On or Off.
2) Signal Control
You can adjust the R Phase, G Phase, B Phase, Gain and
Sharpness manually.
Size
You can switch the Size.
1) 16:9
2) 4:3
PIP Picture
You can adjust the PIP Screen Settings.
1) Contrast
: Adjusts the Contrast of the PIP window on the screen.
2) Brightness
: Adjusts the Brightness of the PIP window on the screen.
3) Sharpness
: Adjusts the difference between the lightest and darkest
areas of the PIP window.
4) Color
: Adjusts the Color of the PIP window on the screen.
5) Tint
: Adds a natural tone to the PIP window.
Available Mode : PIP
AV / S-Video / Component Mode
1) Coarse
/ Fine
3) Position
1) Signal
Balance
2) Signal
Control
Available Mode
OSD
: PC / BNC / DVI
: AV
: S-Video
: Component
Description
Mode
The Monitor has four automatic picture settings ("Dynamic",
"Standard", "Movie" and "Custom") that are preset at the
factory.
You can activate either Dynamic, Standard, Movie, or
Custom. You can select "Custom" which automatically recalls
your personalized picture settings.
- The direct button on the remote control is 'P.MODE'
button.
1) Dynamic
2) Standard
3) Movie
4) Custom
Custom
You can use the on-screen menus to change the contrast
and brightness according to personal preference.
1) Contrast
: Adjusts the Contrast.
2) Brightness
: Adjusts the Brightness.
3) Sharpness
: Adjust the picture sharpness.
4) Color
: Adjust the picture color.
5) Tint ( Available in AV/S-Video Mode Only )
: Adds a natural tone to the display.
Color Tone
The tone of the color can be changed. The individual color
components are also user adjustable.
1) Cool2
2) Cool1
3) Normal
4) Warm1
5) Warm2
Size
You can switch the Size.
1) 16:9
2) Panorama
3) Zoom 1
4) Zoom 2
5) 4:3
- ZOOM1, ZOOM2, Panorama are not available in 1080i(or
over 720p) of DTV.
Digital NR
- Digital Noise Reduction.
You can turn the Noise Elimination feature Off/On.
The Digital Noise Elimination feature allows you to enjoy
: MagicNet
Play
clearer and crisper images.
Off
On
Film Mode
You can turn Film Mode Off/On.
The Film Mode feature offers you a theater-quality viewing
experience.
Off
DNIe Demo
- Digital Natural Image engine
Samsung's new technology brings you more detailed images
with contrast and white enhancement and 3D noise
reduction. A New image compensation algorithm gives
brighter, clearer images to our customers. DNIe technology
will match every signal to your eyes.
On
You can compare a screen with DNle to that without DNle.
The left half will show an image with DNle while the right half
will display the image without DNle.
This monitor supports the DNle feature by default.
Off
: Switches off the DNIe Demo mode.
On
: Switches on the DNIe Demo mode.
PIP Picture
You can adjust the PIP Screen Settings.
1) Contrast
: Adjusts the Contrast of the PIP window on the screen.
2) Brightness
: Adjusts the Brightness of the PIP window on the screen.
Available Mode : PIP
Sound
Available Mode
: PC / BNC / DVI
: AV
: S-Video
: Component
: MagicNet
OSD
Description
Mode
The Monitor has a built-in high fidelity stereo amplifier.
1) Standard
: Choose Standard for the standard factory settings.
2) Music
: Choose Music when watching music videos or concerts.
3) Movie
: Choose Movie when viewing movies.
4) Speech
: Choose Speech when watching a show that is mostly
dialogue (i.e., news).
5) Custom
: Choose Custom if you want to adjust the settings
according to personal preference.
Custom
The sound settings can be adjusted to suit your personal
preference.
1) Bass
: Emphasize low frequency audio.
2) Treble
: Emphasize high frequency audio.
3) Balance
: Allows you to adjust the sound balance between the left and
right speakers.
- You can hear the sound even when the sound value is
set to 0.
Dolby
Virtual
Dolby Virtual Sound Off/On (Dolby Virtual simulates the effect
of the Dolby Surround sound system, recreating the movietheatre or concert-hall- quality sound.)
Off
On
BBE
The direct button on the remote control is 'BBE' button.
BBE (Bass Booster Effect) recreates the natural sound and
improves sound clarity through boosting high and low range
frequencies.
As a result, high sounds are clearer, brilliant and finely
detailed while low sounds are tight, well-defined and
harmonically rich.
Off
On
BBE and Dolby Virtual cannot be functioned at the same time.
Sound
Select
You can select either Main or Sub when PIP is On.
Main
Sub
Available Mode : PIP
Setup
Play
Available Mode
OSD
Time
: PC / BNC / DVI
: AV
: S-Video
: Component
Description
Use to choose one of 4 time settings, Clock Set, Sleep Timer,
On Timer, and Off Timer.
1) Clock Set
: Current Time Setting.
2) Sleep Timer
: Use to set the Monitor to turn off automatically in
certain minutes.
(Off, 30, 60, 90, 120, 150, 180)
3) On Timer
: Use to set the Monitor to turn on automatically at a
preset time.
Use to control the mode, volume level at the time the
monitor turns on automatically.
4) Off Timer
: Use to set the monitor to turn off automatically at a
preset time.
When you select turning Yes the On Timer or Off
Timer when Clock Set is undefined, a guiding
message pops up: "Set the clock first.".
Lamp Control
Used to adjust inverter lamp in order to reduce energy
consumption.
Language
You can choose one of 11 languages.
: MagicNet
Play
1) Clock Set
2) Sleep Timer
3) On Timer
4) Off Timer
The language chosen affects only the language of the OSD.
It has no effect on any software running on the computer.
Menu
Transparency
Changes the opaqueness of the background of the OSD.
1) High
2) Medium
3) Low
4) Opaque
Safety
Lock PIN
You can change the password.
Reset
Picture parameters are replaced with the factory default
values.
1) Image Reset
2) Color Reset
1) Image Reset
2) Color Reset
Video Wall
A Video Wall is a set of video screens that are connected together, so
that each screen shows a part of the whole picture or so that the same
picture is repeated on each screen.
1) Video Wall
: Turns Off/On the Video Wall function of the selected display.
Off
On
2) Format
: The format can be selected to see a divided screen.
Full
Provides a full screen without any margins.
Natural
Displays a natural image with the original aspect ratio intact.
3) Screen Divider
: The screen can be divided into.
You can select a number of screens with a different layout when
dividing.
Select a mode from Screen Divider.
Select a display from Display Selection.
The place will be set up by pressing a number in the
selected mode.
z
z
z
1) Video Wall
2) Format
3) Screen Divider
2*2
3*3
4*4
1*5
5*1
When Video Wall is running, the PIP, Auto Adjustment,
Image Lock, and Size functions are not available.
Launching Video Wall while PIP is running, will switch
PIP Off.
Video Wall does not operate in MagicNet mode.
Resolution
Select
When the picture is not displayed properly on the screen when setting
the graphics card resolution of the computer to 1024 x 768 @ 60Hz,
1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x768 @ 60Hz, by
using this function(Resolution Select) you can have the picture
displayed on the screen in the specified resolution.
Off
1024 X 768
1280 X 768
1360 X 768
1366 X 768
Selecting the menu is only allowed when the graphics
resolution is set to 1024 x 768 @ 60Hz, 1280 x 768 @
60Hz, 1360 x 768 @ 60Hz or 1366 x768 @ 60Hz.
Screen Scroll
The Screen Scroll function is used to prevent afterimages that may
appear when a still picture is displayed on the screen over a long time.
- The Screen Scroll function scrolls the screen for the specified period of
time.
- This function is not available when the power is turned off.
1) Auto Scroll
: Determines whether to turn the Screen Scroll function On or Off.
Off
On
2) Interval
: Determines the time interval to run the Screen Scroll operation.
(1~10 Hours)
The time is calculated on the basis of the power on time.
By default, the time is set to 10 hours.
1~10 Hours
1) Auto Scroll
2) Interval
3) Second
3) Second
: Determines the time period to run the Screen Scroll operation.
(1~5 Seconds)
By default, the time is set to 5 seconds.
1~5 Seconds
Multi Control
Available Mode
OSD
Multi Control
: PC / BNC / DVI
: AV
: S-Video
: Component
Description
Assigns individual ID to the SET.
1) ID Setup
: Assigning distinctive IDs to the SET.
2) ID Input
: Use to select the transmitter functions of the individual SET.
Only the SET whose ID corresponds to the transmitter setting
becomes activated.
Direct Functions
: MagicNet
Play
1) ID Setup
2) ID Input
Available Mode
OSD
: PC / BNC / DVI
: AV
: S-Video
: Component
Description
MAGICNET
Move to the MagicNet OSD screen.
MDC
Move to the Multi Control OSD screen.
LOCK
Set the Safety Lock function.
1) Lock On
: It will be locked on.
2) Lock Off
: It wil be locked off.
When setting the Lock function, you can only
operate power and lock buttons on the remote
control and set.
The preset password on the monitor is "0000".
MagicNet
: MagicNet
Play
1) Lock On
2) Lock Off
z
z
z
z
z
z
z
z
The operating system for this set supports English only so the other languages
might be corrupt on screen.
For MagicNet, the remote control is available for its operation. However, you are
recommended to use a separate USB keyboard.
For MagicNet with the Device mode, moving device surrounding while booting may
cause errors. Set up device surrounding only if monitor turns on or doing well.
Do not unplug the LAN cable used for the network (ex: video display). Otherwise,
the program (MagicNet) may stop. If you do unplug the cable, restart the system.
Do not unplug the LAN cable used by an USB device (ex: video display).
Otherwise, the program (MagicNet) may stop.
To access other sources, press the SOURCE button in MagicNet.
The preset password on the monitor is "000000".
The server program's Power-On option works only if the monitor's power is
completely shut off.
Please make sure not to use the Power-On option when the monitor is in the
process of shutting up since it can possibly cause systemetic error on the monitor.
In the OSD image of MagicNet, Network mode is the same as Device.
z
z
When using MagicNet with MagicNet Server Program : execute Network mode.
When using MagicNet with the device directly connected to monitor : execute Device
mode.
OSD
Description
Photo
JPEG, BMP file format is supported.
1) Auto
: Automatically fits the image to the window.
/ Original
: Shows the properties of an original file.
2) Slide Show
: Displays the properties of the original file as they are.
3) Interval
: Controls the time intervals between image files for a slide
show.
(5 Sec, 10 Sec, 20 Sec, 30 Sec, 60 Sec)
4) Rotation
: Displays an image file by turning it clockwise by 90 .
5) Zoom
: Displays an enlarged picture.
6) Close
: Closes Menu for image control.
Music
MP3 file format is supported.
Movie
AVI, MPEG1/2, DivX 4.x, DivX 5.x file format is supported.
1) Play
: Plays a movie file.
Play
1)
Auto/Original
2) Slide
Show
3) Interval
4) Rotation
5) Zoom
6) Close
1) Play
2) Full Size
: Plays a movie file in full screen.
2) Full Size
OFFICE/HTML PPT(Power Point), DOC(MS Word), XLS(MS Excel), PDF,
HTML, HTM files are displayed.
Internet
Connects to the Internet.
Setup
You can set various functions in MagicNet mode.
You must enter the password to access Setup mode.
z
z
z
The password should be between 6 and 12 characters
in numeric format.
(You should enter a password between 6 and 12
characters in numeric format)
If you enter the wrong password three times, the setup
configuration is reset and a warning message from the
server appears.
If you forget the password, enter Info, 8, 2 and 4 on the
remote control to initialize the password. This will reset
the previous settings of Setup mode.
1) Schedule View
: Displays a schedule.
2) TCP/IP
: You can change the TCP/IP settings.
3) Homepage
: You can change the Internet primary address.
4) Network Setup
: You can modify the network settings.
5) Change Password
: You can change the password.
6) Keyboard
: In MagicNet you can select a preferred keyboard language.
When the selection is over, MagicNet will reboot, and the
selected keyboard language can be used.
This function recognizes the keyboard input in
the selected language. The program language
itself does not change into the selected
language.
1) Schedule
View
2) TCP/IP
3) Homepage
4) Network
Setup
5) Change
Password
6) Keyboard
SyncMaster 460P
Input
Available Mode
OSD
Source List
: PC / BNC / DVI
: AV
: S-Video
Description
Use to select PC, BNC or other external input sources
connected to the Monitor.
Use to select the screen of your choice.
- The direct button on the remote control is 'SOURCE'
button.
The PIP turns off when the monitor is switched to
an external source.
1) PC
2) BNC
3) DVI
4) AV
5) S-Video
6) Component
PIP
When external A/V devices such as VCRs or DVDs are
connected to the monitor, PIP allows you to watch video from
those devices in a small window super-imposed on the PC
: Component
Play
Video signal. (Off/On)
More than one PIP couldn't be overlapped on
screen as BNC and the component use the same
terminal.
1) PIP
- The direct button on the remote control is 'PIP' button.
Off
On
: Turn the PIP Screen on or off.
2) Source
- The direct button on the remote control is 'SOURCE'
button.
PC / DVI
: AV / S-Video / Component Mode
BNC
: AV / S-Video Mode
AV / S-Video
: PC / BNC / DVI Mode
Component
: PC / DVI Mode
: Select the input source for the PIP.
3) Swap
- The direct button on the remote control is 'SWAP' button.
: Swapping the contents of the PIP and main image.
The image in the PIP window will appear on the main
screen, and the main screen image will appear in the PIP
window.
4) Size
- The direct button on the remote control is 'SIZE' button.
: Change the Size of the PIP window.
If you select
,
,
in Size, Position and Transparency
will not be activated.
5) Position
: Change the Position of the PIP window.
6) Transparency
High
Medium
Low
Opaque
: Adjust the Transparency of PIP windows.
Available Mode : PIP
Edit Name
Name the input device connected to the input jacks to make
your input source selection easier.
1) PC
2) BNC
3) DVI
4) AV
5) S-Video
6) Component
Picture
PC / BNC /DVI Mode
1) PIP
2) Source
3) Swap
4) Size
5) Position
6) Transparency
Available Mode
OSD
: PC / BNC / DVI
: AV
: S-Video
: Component
Description
MagicBright™
MagicBright™ is a new feature providing the optimum
viewing environment depending on the contents of the image
you are watching.
Currently four different modes are available: Entertain,
Internet,Text and Custom.
Each mode has its own pre-configured brightness value. You
can easily select one of four settings by simply pressing the
MagicBright™ control button.
- The direct button on the remote control is 'M/B' button.
1) Entertain
: High brightness
For watching motion pictures such as a DVD or VCD.
2) Internet
: Medium brightness
For working with a mixture of images such as text and
graphics.
3) Text
: Normal brightness
For documentations or works involving heavy text.
4) Custom
Although the values are carefully chosen by our engineers,
the pre-configured values may not be comfortable to your
eyes depending on your taste.
If this is the case, adjust the brightness and contrast by
using the OSD menu.
Custom
You can use the on-screen menus to change the contrast
and brightness according to personal preference.
1) Contrast
: Adjust the Contrast.
2) Brightness
: Adjust the Brightness.
If you adjust picture using Custom function, MagicBright will turn to Custom mode.
Color Tone
The tone of the color can be changed.
1) Cool
2) Normal
3) Warm
4) Custom
Color Control
Adjust the individual R, G, B color controls.
1) Red
2) Green
Play
3) Blue
If you adjust picture using Color Control function, Color Tone will turn to Custom mode.
Image Lock
Image Lock is used to fine-tune and get the best image by
removing noise that creates unstable images with jitter and
shimmer. If satisfactory results are not obtained using the
Fine adjustment, use the Coarse adjustment and then use
Fine again.
1) Coarse
: Removes noise such as vertical stripes. Coarse adjustment
may move the screen image area. You may relocate it to the
center using the horizontal control menu.
2) Fine
: Removes noise such as horizontal stripes. If the noise
persists even after fine tuning, repeat it after adjusting the
frequency (clock speed).
3) Position
: Adjusts the screen location horizontally and vertically.
Auto
Adjustment
The values of Fine, Coarse, position are adjusted
automatically.
If you change resolution in the control panel, auto function
will be executed.
- The direct button on the remote control is 'AUTO'
button.
Signal
Balance
Used to make up for the weak RGB signal which has been
transmitted by a long signal cable.
1) Signal Balance
You can select with the signal control either On or Off.
2) Signal Control
You can adjust the R Phase, G Phase, B Phase, Gain and
Sharpness manually.
Size
You can switch the Size.
1) 16:9
2) 4:3
PIP Picture
You can adjust the PIP Screen Settings.
1) Contrast
: Adjusts the Contrast of the PIP window on the screen.
2) Brightness
: Adjusts the Brightness of the PIP window on the screen.
3) Sharpness
: Adjusts the difference between the lightest and darkest
areas of the PIP window.
4) Color
: Adjusts the Color of the PIP window on the screen.
5) Tint
: Adds a natural tone to the PIP window.
Available Mode : PIP
AV / S-Video / Component Mode
1) Coarse
/ Fine
3) Position
1) Signal
Balance
2) Signal
Control
Available Mode
OSD
: PC / BNC / DVI
: AV
: S-Video
Description
Mode
The Monitor has four automatic picture settings ("Dynamic",
"Standard", "Movie" and "Custom") that are preset at the
factory.
You can activate either Dynamic, Standard, Movie, or
Custom. You can select "Custom" which automatically recalls
your personalized picture settings.
- The direct button on the remote control is 'P.MODE'
button.
1) Dynamic
2) Standard
3) Movie
4) Custom
Custom
You can use the on-screen menus to change the contrast
and brightness according to personal preference.
1) Contrast
: Adjusts the Contrast.
2) Brightness
: Adjusts the Brightness.
3) Sharpness
: Adjust the picture sharpness.
4) Color
: Adjust the picture color.
5) Tint ( Available in AV/S-Video Mode Only )
: Adds a natural tone to the display.
Color Tone
The tone of the color can be changed. The individual color
components are also user adjustable.
1) Cool2
2) Cool1
3) Normal
4) Warm1
5) Warm2
Size
You can switch the Size.
1) 16:9
2) Panorama
3) Zoom 1
4) Zoom 2
5) 4:3
- ZOOM1, ZOOM2, Panorama are not available in 1080i(or
over 720p) of DTV.
Digital NR
- Digital Noise Reduction.
You can turn the Noise Elimination feature Off/On.
The Digital Noise Elimination feature allows you to enjoy
: Component
Play
clearer and crisper images.
Off
On
Film Mode
You can turn Film Mode Off/On.
The Film Mode feature offers you a theater-quality viewing
experience.
Off
DNIe Demo
- Digital Natural Image engine
Samsung's new technology brings you more detailed images
with contrast and white enhancement and 3D noise
reduction. A New image compensation algorithm gives
brighter, clearer images to our customers. DNIe technology
will match every signal to your eyes.
On
You can compare a screen with DNle to that without DNle.
The left half will show an image with DNle while the right half
will display the image without DNle.
This monitor supports the DNle feature by default.
Off
: Switches off the DNIe Demo mode.
On
: Switches on the DNIe Demo mode.
PIP Picture
You can adjust the PIP Screen Settings.
1) Contrast
: Adjusts the Contrast of the PIP window on the screen.
2) Brightness
: Adjusts the Brightness of the PIP window on the screen.
Available Mode : PIP
Sound
Available Mode
: PC / BNC / DVI
: AV
: S-Video
: Component
OSD
Description
Mode
The Monitor has a built-in high fidelity stereo amplifier.
1) Standard
: Choose Standard for the standard factory settings.
2) Music
: Choose Music when watching music videos or concerts.
3) Movie
: Choose Movie when viewing movies.
4) Speech
: Choose Speech when watching a show that is mostly
dialogue (i.e., news).
5) Custom
: Choose Custom if you want to adjust the settings
according to personal preference.
Custom
The sound settings can be adjusted to suit your personal
preference.
1) Bass
: Emphasize low frequency audio.
2) Treble
: Emphasize high frequency audio.
3) Balance
: Allows you to adjust the sound balance between the left and
right speakers.
- You can hear the sound even when the sound value is
set to 0.
Dolby
Virtual
Dolby Virtual Sound Off/On (Dolby Virtual simulates the effect
of the Dolby Surround sound system, recreating the movietheatre or concert-hall- quality sound.)
Off
On
BBE
The direct button on the remote control is 'BBE' button.
BBE (Bass Booster Effect) recreates the natural sound and
improves sound clarity through boosting high and low range
frequencies.
As a result, high sounds are clearer, brilliant and finely
detailed while low sounds are tight, well-defined and
harmonically rich.
Off
On
BBE and Dolby Virtual cannot be functioned at the same time.
Sound
Select
You can select either Main or Sub when PIP is On.
Main
Sub
Available Mode : PIP
Setup
Play
Available Mode
OSD
Time
: PC / BNC / DVI
: AV
: S-Video
: Component
Description
Use to choose one of 4 time settings, Clock Set, Sleep Timer,
On Timer, and Off Timer.
1) Clock Set
: Current Time Setting.
2) Sleep Timer
: Use to set the Monitor to turn off automatically in
certain minutes.
(Off, 30, 60, 90, 120, 150, 180)
3) On Timer
: Use to set the Monitor to turn on automatically at a
preset time.
Use to control the mode, volume level at the time the
monitor turns on automatically.
4) Off Timer
: Use to set the monitor to turn off automatically at a
preset time.
When you select turning Yes the On Timer or Off
Timer when Clock Set is undefined, a guiding
message pops up: "Set the clock first.".
Lamp Control
Used to adjust inverter lamp in order to reduce energy
consumption.
Language
You can choose one of 11 languages.
Play
1) Clock Set
2) Sleep Timer
3) On Timer
4) Off Timer
The language chosen affects only the language of the OSD.
It has no effect on any software running on the computer.
Menu
Transparency
Changes the opaqueness of the background of the OSD.
1) High
2) Medium
3) Low
4) Opaque
Safety
Lock PIN
You can change the password.
Reset
Picture parameters are replaced with the factory default
values.
1) Image Reset
2) Color Reset
1) Image Reset
2) Color Reset
Video Wall
A Video Wall is a set of video screens that are connected together, so
that each screen shows a part of the whole picture or so that the same
picture is repeated on each screen.
1) Video Wall
: Turns Off/On the Video Wall function of the selected display.
Off
On
2) Format
: The format can be selected to see a divided screen.
Full
Provides a full screen without any margins.
Natural
Displays a natural image with the original aspect ratio intact.
3) Screen Divider
: The screen can be divided into.
You can select a number of screens with a different layout when
dividing.
1) Video Wall
2) Format
3) Screen Divider
Select a mode from Screen Divider.
Select a display from Display Selection.
The place will be set up by pressing a number in the
selected mode.
z
z
z
2*2
3*3
4*4
1*5
5*1
When Video Wall is running, the PIP, Auto Adjustment,
Image Lock, and Size functions are not available.
Launching Video Wall while PIP is running, will switch
PIP Off.
Resolution
Select
When the picture is not displayed properly on the screen when setting
the graphics card resolution of the computer to 1024 x 768 @ 60Hz,
1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x768 @ 60Hz, by
using this function(Resolution Select) you can have the picture
displayed on the screen in the specified resolution.
Off
1024 X 768
1280 X 768
1360 X 768
1366 X 768
Selecting the menu is only allowed when the graphics
resolution is set to 1024 x 768 @ 60Hz, 1280 x 768 @
60Hz, 1360 x 768 @ 60Hz or 1366 x768 @ 60Hz.
Screen Scroll
The Screen Scroll function is used to prevent afterimages that may
appear when a still picture is displayed on the screen over a long time.
- The Screen Scroll function scrolls the screen for the specified period of
time.
- This function is not available when the power is turned off.
1) Auto Scroll
: Determines whether to turn the Screen Scroll function On or Off.
Off
On
2) Interval
: Determines the time interval to run the Screen Scroll operation.
(1~10 Hours)
The time is calculated on the basis of the power on time.
By default, the time is set to 10 hours.
1~10 Hours
1) Auto Scroll
2) Interval
3) Second
3) Second
: Determines the time period to run the Screen Scroll operation.
(1~5 Seconds)
By default, the time is set to 5 seconds.
1~5 Seconds
Multi Control
Available Mode
OSD
Multi Control
: PC / BNC / DVI
: AV
: S-Video
Description
Assigns individual ID to the SET.
1) ID Setup
: Assigning distinctive IDs to the SET.
2) ID Input
: Use to select the transmitter functions of the individual SET.
Only the SET whose ID corresponds to the transmitter setting
becomes activated.
Direct Functions
: Component
Play
1) ID Setup
2) ID Input
Available Mode
OSD
: PC / BNC / DVI
: AV
: S-Video
Description
MDC
Move to the Multi Control OSD screen.
LOCK
Set the Safety Lock function.
1) Lock On
: It will be locked on.
2) Lock Off
: It wil be locked off.
When setting the Lock function, you can only
operate power and lock buttons on the remote
control and set.
The preset password on the monitor is "0000".
: Component
Play
1) Lock On
2) Lock Off
Introduction to
MagicNet
|
Schedule OSD
| MDC |
Upper
|
Menu
Remote Control
Adjustment
|
Removing
|
Program
Troubleshooting
Introduction to MagicNet
MagicNet transmits media files (photo, audio and movie files) and office files (PowerPoint, Excel,
Word, HTML and PDF files) existing on a server to monitors using the Ethernet network of the
server/client architecture.
Several monitors can be connected to a server, and any file can be transmitted to any monitor over
the network.
Files can be transmitted in two ways: the server sends files to the monitors after registering with the
schedule; or the monitor searches for the files
registered in the library of the server, sends the files to the monitors, and plays those files after
receiving them via the network.
When more than one server is connected, you can select a server from the monitor and receive the
schedule.
Each monitor is capable of accessing the Internet by itself.
Servers and monitors are connected over the network, and each server and monitor has a proper
name to confirm each other.
Hence, the name of the server must be identical between the server and the clients for a normal
connection.
That is, when a server's name is "MagicNet", only monitors set to "MagicNet" can be connected to this
server.
When a server name does not exist under the name set in the monitor, it will wait until the server
with the identical name appears.
However, when the auto connection function is on, it will try to connect to other servers, and will
connect to the server that gives the first reply.
Added Functions in MagicNet 2.0
1. Multiple Display Control (MDC)
The Multiple Display Control (MDC) is a newly added function in MagicNet 2.0,
which can easily control several monitors from a PC simultaneously.
MDC checks and controls the status of monitors that normally connect via the network.
2. Account Management
|
Specifications
This function prevents a random user from freely using MagicNet, by placing limits on the operation of
functions according to the account privilege.
3. Update
You can update a monitor's MagicNet from the server.
However, this function only works when it is connected to a server/monitor with MagicNet Ver 2.0 or higher.
4. Controlling Local Storage Devices/USB File Control of Monitors
You can copy or delete files to a monitor's local storage device or via USB connected to the monitor.
5. Schedule Pause
This function pauses the ongoing schedule in the monitor, and is useful in the event of urgently needing to
conduct other work.
Press the buttons in the order of [+100]-[8]-[2]-[4]-[ENTER] on the monitor with the remote control, and
the schedule will pause temporarily.
To resume the temporarily paused schedule, press the buttons in the order of [PRE-CH]-[8]-[2]-[4][ENTER]on the remote control.
Introduction to
MagicNet
|
Upper
MDC
Schedule
|
|
|
Menu
Adjustment
OSD
Remote Control
Adjustment
|
Removing
|
Program
Troubleshooting
| Specifications
Schedule OSD
The server program's Power-On option works only if the monitor's power is completely
shut off. Please make sure not to use the Power-On option when the monitor is in the
process of shutting up since it can possibly cause systemetic error on the monitor.
Registering to the Library
Library List
Monitor Preview Window
Network
File Information
MagicNet/Network On/Off Status or Image Selection Menu
Play Control Tool
Registering / the Schedule
Date
Monitors connected via the Network
Fields Window
Registering to the Library
What is the Library?
The library consists of a collection of files which can be played from a monitor connected to the
MagicNet program.The monitor can only play files with the supported formats registered in the library.
The library only accepts files of the supported formats.
z
z
z
z
Press the "Reg. Library" button to select files that can be registered to the library.
It has been designed in such a way that only files playable by a monitor can be registered. The
selected files are analyzed and the result is displayed.
Files added to the library are first, automatically classified in the list ( ) as movie, audio, photo
and office files, and then they are further classified according to the file type.
The Fields window( )displays the registered files and their information.
Library List
Files added to the library are first, automatically classified in the list as movie, audio, photo and office
files, and then they are further classified according to their properties.
z
z
z
z
z
All file : Displays all files which are registered in the library.
Video File : Classified by actor (actress)
Music File : Classified by musician and album
Image File
Office file :Classified by file type (PowerPoint, Excel, Word, PDF, HTML)
Monitor Preview Window
This window is used either to preview a file (a movie or photo file) registered in the library list (
selected in the fields window( ), or to monitor a monitor.
)and
1. Playing a file registered in the library
Click on a classification in the library list ( ), and the files under the selected classification are
displayed in the fields window ( ). Then, double-click on a file in the fields window to play it.
While playing, the file information is displayed in
Only audio, movie, and image files can be
played. For office files, only file information is displayed in
. However, if monitoring for a
monitor is proceeding, the information being monitored is displayed instead.
2. Monitoring the selected monitor (Preview)
With the relevant monitor selected by a number
(the name of the monitor will be displayed
in the field
), the screen played by the currently-selected monitor will be displayed.
Audio, video and image files can be played, while only the file information appears for office
files.
(In this case, only files registered in the library of the server will be played, and the local/USB
files on the monitor will display only the basic information. In addition, when the output source
of a monitor does not belong to MagicNet, information on the relevant output source will be
displayed.)
Network
The status bar next to the monitor name will display the overall network status (traffic) of all the monitors
connected to the server. For example, assume that the network system capability is 100Mbs and a 100Mbs
network card is installed in the server. If there is no network traffic used for other purposes, three monitors
are connected, and each monitor uses 10Mbs of traffic, the progression will be indicated as about 30%.
Server PC Environment: Recommended (CPU: 3GHz, RAM:512M, Ethernet: 100M)
Network Environment: Local network not connected externally
Normal: Server PC network bandwidth: 50% ~ 60%
Max: Server PC network bandwidth: 90% or more (not recommended)
For a LAN-connected environment, the connectable number of devices may be reduced depending on
the availability of neighboring networks.
File Information
This will display the name, date, size and resolution of the current file.
MagicNet/Network On/Off Status or Image Selection Menu
Displays the On and Off status for the power and the network.
Selecting an image file will change to the appropriate image menu.
Extended Image Menu
z
Slide
z
z
z
z
Previous
z
z
z
Next
z
z
Stop
z
z
Full Screen
Play Control Tool
When the files are selected in the library list :
Sequentially displays the image files registered to the library.
When monitoring information is being played from a schedule :
Displays the image files registered to the schedule.
When monitoring the information which the monitor user is selecting
and playing :
This function is disabled.
When the files are selected in the library list :
Displays the previous file.
When monitoring information is being played from a schedule :
Displays the previous file. If a slide show is in progress, the slide show is
stopped.
When monitoring the information which the monitor user is selecting
and playing :
This function is disabled.
When the files are selected in the library list :
Displays the next file.
When monitoring information is being played from a schedule :
Displays the next file. If a slide show is in progress, the slide show is
stopped.
When monitoring the information which the monitor user is selecting
and playing :
This function is disabled.
When the files are selected in the library list :
Stops the slide show.
When monitoring information is being played from a schedule :
Stops the slide show.
When monitoring the information which the monitor user is selecting
and playing :
This function is disabled.
Enlarges/shrinks an image file to fit to the full screen.
Double-click the screen to return to the original image size.
Controls for play, stop, next file, previous file, and volume when playing a movie or audio file.
z
z
Play / Pause
z
z
z
Stop
z
z
z
Previous/Next
z
z
first/last
5 seconds
z
z
When the files are selected in the library list :
Plays the audio/movie files registered with the library list.
When monitoring information is being played from a schedule :
Plays the audio/movie files registered with the schedule.
When monitoring the information which the monitor user is selecting
and playing : This function is disabled.
When the files are selected in the library list :
Stops playing an audio/movie file.
When monitoring information is being played from a schedule : This
function is disabled.
When monitoring the information which the monitor user is selecting
and playing : This function is disabled.
When the files are selected in the library list :
Plays the previous/next file in the library list.
When monitoring information is being played from a schedule :
Plays the previous/next file in the schedule list.
When monitoring the information which the monitor user is selecting
and playing : This function is disabled.
When the files are selected in the library list :
Plays the first/last 5 seconds of the file.
When monitoring information is being played from a schedule :
Plays the first/last 5 seconds of the file.
When monitoring the information which the monitor user is selecting
and playing : This function is disabled.
Registering/Editing the Schedule
Allows you to register the files to be run on the monitor in advance.
Schedule Register Menu
z
Library : Registering the schedule through the library
Among the files on the server PC, files that are added through the registration procedures in the
library can be registered with the schedule.
1. When selecting a file from among the files already registered, or selecting a random file
from the schedule registration window,
the file is selected as a schedule file through the library registration procedures.
2. When selecting an image file for the schedule file, you can add background music from
among the following music files. If a schedule file is not an image file, the add/delete
button for the background music is not activated.
z
Storage (Local/USB) : Registering the Storage (Local/USB) File Schedule
You can select a file from among the local storage of the monitor, or from the USB connected to
the monitor to register the selected file with the schedule.
1. From the monitor list, select a monitor where the schedule is to be registered.
The add/delete button of the schedule file is only activated when selecting a monitor that
is currently connected to the server.
2. You can add a file from the local storage device of the monitor, or from the USB
connected to the monitor by pressing the add button. In this case, it will not go through
the library registration procedures on the server.
3. When selecting an image file for the schedule file, you can add background music.
When a schedule file is not an image file, the add/delete button for the background music
is not activated.
z
Input/Power : Registering the Input/Power Schedule
You can register the input source or Power Off for the monitor with the schedule.
1. You can schedule a change of the output source or the power for the monitor.
2. After selecting a monitor where the schedule is to be registered in the monitor list,
select an input source or Power Off from the Input/Power Selection.
3. Set the schedule time and press the confirm button.
It will change into the registered output source at the start of the schedule,
and it will correctly return to the MagicNet Menu screen when the schedule is over.
1. Selecting a Monitor
Selecting either all monitors or a specific monitor, where the schedule will be added to, is
available from among the monitors connected via the network.
2. Schedule a File Add/Delete
You can select, add or delete the file to be added to the schedule.
3. Background Music Add/Delete
Available only when using image files.
Selects an audio file to use as the background music in advance when playing an image file
registered to the schedule.
4. Schedule
{
Start Time
This means the starting time of a schedule, which can be entered in
years/months/days/hours/minutes.
It is possible to set the start time of a schedule within 7 days of the current day,
however setting a time later than 7 days from now is not available.
{
{
Total Run Time
The total period of time reserved in the schedule
Repeat Function
„
„
In repeating the schedule at an interval of a day/week/month,
select the interval to be repeated and the date for completing the repeat.
The end date of such a repetition can be set within 1 year of the current date.
If you do not select the repeat option or do not select the end date of the
repetition,
the schedule will be added once by default.
5. Options
{
Insert between Existing Schedules
This means that a new schedule will be inserted without affecting the total playing time
of the existing schedules. If a new schedule to be inserted,
intrudes on the end time of an existing schedule, the start time selected by the user is
ignored,
and the start time is changed to after the end time of the existing schedule. When the
new schedule to be added intrudes on the start time of an existing schedule,
the start time of the existing schedule is changed to after the end time of the new
schedule.
{
Ignore/Overwrite Existing Schedules
Existing schedules are ignored, and a new user schedule overwrites at the required time.
If the new schedule overlaps with an existing schedule, the time of the existing schedule
can be changed or even be deleted,
since it is overwritten by the new schedule.
Date
Displays the registered schedules in the Fields window (
Monitors Connected via the Network
) whose date are later than today (
).
Lists the names of monitors registered via the network.
When a monitor is connected to the network, its background color changes to yellow-green.
z
Reconnect to another server automatically
1. When selecting a monitor that is currently connected to a server in the monitor list and
right-clicking it with the mouse, you can see an item titled 'Reconnect to another server
automatically'.
2. When selecting 'Reconnect to another server automatically', the field in front of the menu
item is marked,
and will also be marked in the option Setup ¡æ Network Setup 'Reconnect to another
server automatically' in the monitor.
3. Selecting this menu enables a monitor to search for another server and connect to a
found server when the connection to the server with the name defined in the Setup is not
available.
Let's say there are two servers called S1 and S2, respectively, and a monitor called C,
which is currently connected to the S1 server. When the connection to S1 fails or stops,
C will automatically be connected to the S2 server.
z
Setting Up a User Password
1. When selecting a monitor that is currently connected to a server in the monitor list and
right-clicking it with the mouse,
you will see an item titled 'Setting up a user's password'.
2. When selecting 'Setting up a user password', the field in front of the menu item is
marked,
and will also be marked in the option Setup ¡æ Network Setup 'Ask for user password' in
the monitor.
3. This is to prevent a random user from using MagicNet indiscriminately.
If you select this option, you will be required to enter your password to access the
MagicNet menus (Network, Photo/Movie/Music/Office of device, etc.).
z
Update
1. When selecting a monitor that is currently connected to a server in the monitor list and
right-clicking it with the mouse,
you can see an item titled 'Update' in the menu.
This item enables you to update MagicNet (File name: NK.bin) on the monitor.
2. This item will be deactivated in monitors that are not connected to a server.
3. If you select the Update item, a window pops up. Search for the path to NK.bin, select it,
and click the Update button.
The update will proceed in two steps:
Download (Save the update file in the monitor) ¡æ Update (MagicNet installation)
4. You may cancel this function during the download stage, but not during the update
stage.
5. Once the update is completed, the monitor will reboot automatically.
6. If you try updating with an abnormal file, a warning message will appear,
and the update will not proceed.
7. Please make sure that the power of the monitor is not turned off while updating once the
download is over.
Furthermore, if the output source is a PC, please turn off the 'monitor off' function in the
power options of the connected PC for the duration of the update.
MagicNet is not operating normally.
If the power turns off during the update, contact our After-Sales Service Center.
z
Schedule Check
1. Select All Monitors:
Checks on all schedules of the registered monitors are available in the (
) field.
Right-clicking the mouse can turn the power ON or OFF as well as deleting the field.
In addition, you can change the name of the monitors.
The server program's Power-On option works only if the
monitor's power is completely shut off. Please make sure not
to use the Power-On option when the monitor is in the
process of shutting up since it can possibly cause systemetic
error on the monitor.
2. Select Monitor :
The schedules of the relevant monitor is queued.
z
Rename
Type a new name and click confirm. The new name will be saved.
Fields Window
Displays the status of a file.
z
z
z
When selecting All Monitors in the Schedule, you can view all schedules registered for each
monitor.
Control the time by double-clicking on a schedule.
When a monitor is selected in the monitor list. Displays the file name including the path,
category, start time, end time and playtime.
1. When the All Monitors entry is clicked in the monitor list (
), schedules are not displayed in a
list, but with images of a box type. The schedules for all monitors in the monitor list are
displayed here. You can control the time by double clicking on a box type schedule, dragging
and dropping a schedule to move it to a different position, and cut, delete and paste a schedule
by using the menus displayed when the right mouse button is clicked.
2. When you click on a monitor in the monitor list ( ), the schedules for that monitor are
displayed in the list. Right-clicking on a schedule list displays a context menu, allowing you to
copy, delete, or edit it. By using the Edit menu, you can change the selected file and time. By
using the Copy menu, you can select a monitor to copy.
3. The files registered to the library are displayed in a list. Right-clicking a file in the list displays a
menu, allowing you to view properties for a schedule and deleting a schedule, depending on the
kind of menu. You can also directly insert the selected file into a schedule.
Introduction to
MagicNet
|
Upper
MDC
Schedule
|
|
|
Menu
Adjustment
OSD
Remote Control
Adjustment
|
Removing
|
Program
Troubleshooting
| Specifications
MDC Adjustment
Multiple Display Control (MDC) is a function for easily controlling
several monitors from a PC.
MDC checks and controls the status of monitors that normally connect via the network.
How to Control
1. When selecting MDC from the monitor list window, the monitoring window and the schedule
window change into a window showing the monitor status
and the control window, respectively.
2. First, select the monitor to apply in the client list window.
3. If you choose All Monitors, all monitors will be selected.
4. If you try to run the detailed functions for each tab without first selecting a monitor, a warning
message will appear.
5. After selecting a monitor, click each MDC tab to run the detailed functions.
In this case, when running menus that cannot be adjusted in the output source, the warning
'Adjustment unavailable' will appear. Furthermore, when running adjustable menus, the
selected values will be applied to the monitor, and the results will be applied to the MDC status
window.
If not applied to the monitor, it will also not be applied to the MDC status window.
The MDC functions comply with the specifications for running the monitor.
MDC OSD
Power
Source
Image
Time
PIP
Settings
Maintenanace
Power
Select Power ON/OFF.
z
z
ON
OFF
When changing the volume, the changed details will appear in an OSD on the monitor screen.
z
0 ~ 100
Source
In the source tab, the output source of the monitor can be changed.
When selecting the following output source, it will change to the relevant output source.
When the relevant device is not connected, a screen with 'Connection required' will appear.
z
z
z
z
z
z
z
PC
BNC
DVI
AV
S-Video
Component
MagicNet
Image
1. Image Size
The size of the current output screen with output sources other than PC signals is adjustable.
When selecting the menu below,
it will be changed to the selected size.
z
z
z
z
z
16:9
Panorama
Zoom1
Zoom2
4:3
2. Image Size PC
Adjusts the output screen size of the PC signal.
When trying to change the size of non-adjustable input sources, a warning message will appear
on the monitor.
z
16:9
z
4:3
Time
1. Current Time
Establishes the standard time of the monitor.
In Hours, Minutes and AM/PM, select the time, and click the Apply button.
The current standard time of the monitor will be set.
To activate the On/Off Timer at the set time, the
Current Time must be set.
z
z
z
Hours
Minutes
AM/PM
2. On Timer
Select the time, output source and volume, and click the Apply button. The monitor will turn on
with the established source and volume at the established time.
When Activated is OFF, the ON Timer will not work.
z
z
z
z
z
z
Hours
Minutes
AM/PM
Activated
Source
Volume
3. Off Timer
Select the time and click the Apply button. The monitor will turn off at the set time.
When Activated is OFF, the Off Timer will not work.
z
z
z
z
Hours
Minutes
AM/PM
Activated
PIP
1. Size
Select a size. (The size selection has an 'ON' function)
2. Source
When selecting sources to be output to PIP, the relevant source will be applied to PIP.
When trying to change a source where PIP cannot be applied or the combination of Main/Sub is
incompatible,
a warning message will appear on the monitor.
Settings
1. Picture
For input sources other than for PC signals,
adjust the Contrast, Brightness, Sharpness, Color, Tint and Color Tone of the monitor.
z
z
z
z
z
z
Contrast
Brightness
Sharpness
Color
Tint
Color Tone
2. Picture PC
When the output sources are PC signals,
adjust the Contrast, Brightness, Sharpness, Color, Tint and Color Tone of the monitor.
z
z
z
z
z
Contrast
Brightness
Red
Green
Blue
3. Audio
Adjust the Bass, Treble and Balance, and set Main/Sub for the Sound Select of
Dolby Virtual ON/OFF, BBE ON/OFF and PIP.
In the course of making adjustments, changes appear as OSDs on the monitor screen.
z
z
z
z
z
z
Bass
Treble
Balance
Dolby Virtual
BBE
Sound Select
4. Adjust Image Lock
Course, Fine, and select Position.
z
z
z
z
Coarse
Fine
Position
Auto Adjustment
Maintenance
1. Lamp Control
You can control the intensity of the lamp.
(Auto/Manual is available. When Auto is running, Manual is off; and when Manual is running,
Auto is off.)
In Auto mode, the lamp is adjusted to the previously set value at the set time.
In Manual, the previous value is maintained.
z
Auto
Hours
Minutes
AM/PM
Value
z
Manual
z
z
z
z
2. Scroll
This function prevents the screen status changing when the same screen is maintained
continuously.
If you select the Period and Time and press the Apply button, the screen
will scroll downwards at the speed of the previously set time in Period.
For example, for Period 1, Time 5, the screen will be renewed every hour at a speed of 5
seconds.
z
z
Period
Time
3. Video Wall
This offers a function that enables you to use several monitors as one screen.
First, select the button that sets the number of monitors to be used and their allocation. The
allocation figure will appear as a selectable button on the side.
For example, when you choose 2*2, selectable buttons in the form of 2 rows and 2 lines
appear,
and if you select number 3 in this matrix, the third screen of the output screen divided by 4 will
show up in the monitor.
z
2*2
3*3
4*4
1*5
5*1
OFF
z
Format
z
z
z
z
z
Introduction to
MagicNet
|
Upper
MDC
Schedule
|
|
|
Menu
Adjustment
OSD
Remote Control
Adjustment
|
Removing
|
Program
Troubleshooting
|
Specifications
Upper Menu
Login / Logout
Change Password
Options
Help
Login / Logout
Before using MagicNet, you first need to login.
After a successful login, the Login button changes to a Logout button. A successful login is required to use
the majority of functions.
When installing MagicNet for the first time, the administrator account is provided on the basis of the
password entered by the user.
When adding an account, you can select from among three account types, and the selected account type
decides the scope of using MagicNet. You may modify or delete the accounts of existing users as well as
adding new users.
Account Type
Administrator
Power User
Operator
z
z
User Name
Password
Scope
You have the authority to use all MagicNet functions.
You are not authorized to use the Options menu and the Update function of
MagicNet.
You are not authorized to use the right mouse button click
in the Library Registration, Options menu, MDC and Monitor List from among the
MagicNet functions.
Change Password
You can change your password in the login status.
Enter your password correctly before logging in.
You will be prompted to enter the password for installing MagicNet, and this password will become the
default password for the administrator account. If you forget the password, please remove the
program and re-install it.
z
z
z
Old Passworld
New Passworld
Confirm Passworld
Options
1. Server Name
In the Options, you can specify the server name for the connection information. The servers and
monitors are connected via the network, and have proper names to identify each other. For a normal
connection, the server name between a server and monitor must match. In other words, when the
name of a server is MagicNet, only monitors whose server names are set to "MagicNet" can be
connected to that server and receive the schedule. When there is no server with that name set in the
monitor, it will wait until a server that matches this name appears. However, when the auto connction
function is ON, it tries to connect to any server, and will connect to the server that replies first.
z
Server Name
2. User Account
When installing MagicNet for the first time, the administrator account is provided on the basis of the
password entered by the user.
When adding an account, select from among three account types, and the selected account type
decides the scope of using MagicNet. You may modify or delete the accounts of existing users as well
as adding new users.
Account Type
Administrator
Power User
Operator
z
z
z
Scope
You have the authority to use all functions of MagicNet.
You are not authorized to use the Options menu and the Update function from
among the MagicNet functions
You are not authorized to use the right mouse button click
in the Library Registration, Options menu, MDC and Monitor List from among the
MagicNet functions.
Create
Modify
Delete
3. File Manager
File manager copies or deletes files.
Copying files can be done either from Server Folder ¡æ Server Folder, Server ¡æ Monitor, Monitor ¡æ
Monitor.
A copy from a monitor to another is available only on the same monitor (i.e. different hard drives o
nthe same monitor).
In the Select Monitor list, only My Computer of the server and the monitor that is correctly connected
to the server will appear.
z
z
Copy File
Delete File
When selecting Options ¡æ File Manager, the
File Management window appears.
You can select a server/monitor from the
select list. When selecting a monitor from the
left window, you are only allowed to select the
same monitor.
After selecting the copy target, press the copy
button. Copying the file will proceed.
If the copy target is not a
Photo/Music/Movie/Office file,
an error message will appear,
and copying will stop.
In addition, when the file size exceeds the
remaining capacity of the target drive,
copying will also stop.
Select the file to be deleted using the same
procedure as for copying a file, and click the
delete button. The file will be completely
deleted from the drive. (The list will be
updated promptly).
However, if you try to delete a file that is
currently running, the error message
"Unable to delete file" will appear.
Copy File
Delete File
Help
1. Help
Runs program help.
2. About MagicNet
Indicates the program version and the copyright details.
Introduction to
MagicNet
|
Upper
MDC
Schedule
|
|
|
Menu
Adjustment
OSD
Remote Control
Adjustment
|
Removing
|
Program
Troubleshooting
Remote Control Adjustment
PHOTO
Supported File Formats
Image File : JPG, BMP
Remote Control
z
When the files are selected in the library list
Previous file
Stop slideshow / View the bottom menu bar
Slideshow
Next file
MUSIC
Supported File Formats
Music File : MP3
Remote Control
z
When the files are selected in the library list
File view on the cursor position /
Play / Pause during playback
Stop playing
Play in 5 seconds
Play 5 seconds earlier
Move to the next file (when the cursor is placed at
the top, it will go back to the last file of the
previous page)
Move to the previous file (when the cursor is
placed at the bottom, it will move to the first file of
the next page)
Move to the next page (when the current page is
the first, it will move to the last page)
| Specifications
Move to the previous page (when the current page
is the last, it will move to the first page)
File view on the cursor position Play
MOVIE
Supported File Formats
Video File : MPEG1, MPEG2-PS, DIVX4, DIVX5
Remote Control
z
When the files are selected in the library list
Move to the top (when the cursor is placed at the
top, it will go back to the last file of the previous
page)
Move to the bottom (when the cursor is placed at
the bottom, it will move to the first file of the next
page)
Move to the next page (when the current page is
the first, it will move to the last page)
Move to the previous page (when the current page
is the last, it will move to the first page)
File view on the cursor position Play
z
Play
Play / Pause during playback
Stop playing
Play 5 seconds earlier
Play in 5 seconds
OFFICE
Supported File Formats
Office File : Power MS Office(Word, Excel, Power Point), HTML, PDF
Remote Control
z
When the files are selected in the library list
Move to the top (when the cursor is placed at the
top, it will go back to the last file of the previous
page)
Move to the bottom (when the cursor is placed at
the bottom, it will move to the first file of the next
page)
Move to the next page (when the current page is
the first, it will move to the last page)
Move to the previous page (when the current page
is the last, it will move to the first page)
File view on the cursor position
z
PDF
Move to the top
Move to the bottom
Move to the next page
Move to the previous page
Exit PDF
z
Excel
Move to the upper cell
Move to the lower cell
Move to the left cell
Move to the right cell
Move to the next page
Move to the previous page
Move to the right sheet
Move to the left sheet
Exit Excel
z
Power point Normal
Move to the top
Move to the previous page
Move to the next page
Move to the previous page
Slideshow
Exit Power point
z
Power point Slideshow
Stop slideshow
Move to the top
Move to the bottom
Move to the next page
Move to the previous page
Exit Power point
z
Word
Move to the top
Move to the bottom
Move to the next page
Move to the previous page
Exit Word
z
HTML
Move to the top
Move to the bottom
Move to the next page
Move to the previous page
Exit HTML
z
Ineternet
Move the mouse cursor up
Move the mouse cursor down
Move the mouse cursor to the left
Move the mouse cursor to the right
Click when the cursor is placed over a link (move
to the link)
Exit the Internet
Introduction to
MagicNet
|
Upper
MDC
Schedule
|
|
|
Menu
Adjustment
OSD
Remote Control
Adjustment
|
Removing
|
Program
Troubleshooting
Removing Program
You can remove MagicNet by using the Add/Remove Options in Windows Programs
or by using the delete menu provided when installing this program.
To remove MagicNet, complete the following steps.
1. Select [Start]->[Settings]->[Control Panel].
2. For Windows XP, select [Start]->[Control Panel].
3. Double-click the [Program Add/Remove] icon in the Control Panel.
4. Click the MagicNet in the [Program Add/Remove] window to highlight it.
5. Click [Change/Remove] to remove it.
6. Click OK to start removal of MagicNet.
7. Wait until the window appears which indicates that program removal is completed.
| Specifications
Introduction to
MagicNet
|
Upper
MDC
Schedule
|
|
|
Menu
Adjustment
OSD
Remote Control
Adjustment
|
Removing
|
Program
Troubleshooting
| Specifications
Troubleshooting
In Preview, the file information can be viewed but not the image
Office files are not displayed. Check the file for the format.
When there is no codec available for the server, no file is displayed. Check the codec
first.
MPEG2, DivX4,5 and AC3 are played normally only when the server has the
corresponding codec available. Please install the corresponding codec.
Conflicts between codecs may occur when various kinds of codecs are installed on one
PC, which results in a program error. And the incomplete installation of a codec may
result in a program malfunction and file playback error.
In a Preview, the program does not operate
When you play a movie or music file in Preview, the player does not operate and stops
to check if the codec is available. Note that conflicts between codecs may occur when
various kinds of codecs are installed on one PC, which results in a program error. And
the incomplete installation of a codec may result in a program malfunction and file
playback error.
When a schedule does not run properly at the designated time:
Please check the status of MagicNet for the monitor and that of the network.
Furthermore, please confirm if the schedule pause function is activated for the monitor.
Schedules will only run when the status of MagicNet and the Network are ON, and will
not run when the monitor schedule is paused.
When the power goes off and returns or the network is disconnected and re-connected,
the current schedule returns to the start.
When the monitor icon is displayed in sky blue not green (normal operation):
This may occur when the network configuration is normal but the connection between
the server and the monitor is not functioning properly. This may occur when the monitor
is connected to another server, not the corresponding one, or the network status is not
normal.
Please check the monitor for the network connection.
Password/Login
The password entered by the user when installing MagicNet will become the default
password of the administrator account.
If you forget your password, please remove the program and install it again.
Introduction to
MagicNet
|
Schedule OSD
| MDC |
Upper
|
Menu
Remote Control
Adjustment
|
Removing
|
Program
Troubleshooting
|
Specifications
Specifications
Supported File Format Spec
Audio
Bit rate
File Format
Resolution
CBR
VBR
Sampling rate
MPEG1
Video
MPEG2 (PS)
DivX 4.x
Peak bitate
720x480 or less
-
9Mbps or less
-
9Mbps or less
DivX 5.x
Audio
Photo
-
MP3
-
Available
Not Available
16kHz or more
JPEG
3500 x 2625
or less
-
-
-
-
-
-
BMP
For MPEG2, only PS (Program Stream) is supported and TS (Transport Stream) is not.
For JPEG, the EXIF Format (Digital Camera) is not supported.
(However, Samsung digital cameras are supported)
Network Configuration (Number of Devices)
Bit rate
Normal
Max
4Mbps
10
20
6Mbps
8
16
9Mbps
5
9
-
20 or more
-
Video
Audio, Photo
Server PC Environment: Recommended (CPU: 3GHz, RAM:512M, Ethernet: 100M)
Network Environment: Local network not connected externally
Normal: Server PC network bandwidth: 50% ~ 60%
Max: Server PC network bandwidth: 90% or more (not recommended)
For a LAN-connected environment, the connectable number of devices may be reduced depending on
the availability of neighboring networks.
Server System Configuration
CPU
RAM
Minimum
P1.8
256M
Recommended
P3.0Ghz
512M
Ethernet
OS
Application
100M
Windows XP
Windows 2000
(Service Pack 4)
WMP 9 or later
Local Device (USB) Connection Speed
For a mass storage device such as a USB hard disk, it takes approximately 3 - 4 seconds for loading 1 GB.
When the user operates MagicNet while the file is loading, a warning message is displayed.
Local Device (USB) compatibility
HID(Human Interface Devices)
: Keyboard, Mouse
MSC(Mass Storage Class)
: Devices using the SCSI(Small Computer System Interface) command set
: FAT(File Allocation Table) System
Exception
: Some manufacturers have wrongly specified their device to be USB standard compatible.
Our product has exception handling procedures. But Some devices are unlikely to work properly.
: Some manufacturers have wrongly specified their device to be SCSI compatible.
Such devices are unlikely to work properly.
: It is recommended that USB devices are purchased after they are tested and confirmed to be compatible.
Self-Test Feature Check
Check the following items yourself before calling for service. Contact the Service Center for
problems that you cannot solve by yourself.
Self-Test Feature Check | Not Optimum Mode |
Maintenance and Cleaning | Symptoms & Recommended Actions
1. Self-Test Feature Check
Your monitor provides a self test feature that allows you to check whether your monitor is functioning
properly.
1. Turn off both your computer and the monitor.
2. Unplug the video cable from the back of the computer.
3. Turn on the monitor.
The figure shown below ("Check Signal Cable") appears on a black background when the monitor is
in its normal working condition though it does not sense any video signal: While in the Self-Test
mode, the LED power indicator remains green and the figure moves around on the screen.
4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the
monitor.
If your monitor screen remains blank after using the previous procedure, check your video controller and
computer system; your monitor is functioning properly.
2. Not Optimum Mode
You can view the screen even in more than 1360x768 resolution. However you will have the following
message for a minute; You can choose to change the screen resolution or stay in the current mode during
that time. And if the resolution is more than 85Hz, you will see the black screen because the monitor does
not support over 85Hz.
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are
supported by the monitor.
3. Maintenance and Cleaning
1. Maintaining the Monitor Case.
Clean with a soft cloth after disconnecting the power cord.
z
z
Do not use benzene, thinner or other flammable substances, or a
wet cloth.
We recommend a Samsung cleansing agent is used to prevent
damage to the screen.
2. Maintaining the Flat Panel Display Screen.
Clean with a soft cloth (cotton flannel) smoothly.
z
z
Never use acetone, benzene or thinner.
(They may cause flaws or deformation of the screen surface.)
The user will be required to pay costs and related expenses for
repair of damages caused by him/her.
4. Symptoms and Recommended Actions
A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the
computer or the video card, this can cause the monitor to become blank, have poor coloring, noise,
Video mode not supported, etc. In this case, first check the source of the problem, and then contact
a Service Center or your dealer.
1. Check if the power cord and the video cables are properly connected to the computer.
2. Check if the computer beeps more than 3 times when booting.
(If it does, request an after-service for the main board of the computer.)
3. If you installed a new video card or if you assembled the PC, check if you installed the adapter(video)
driver and the monitor driver.
4. Check if the scanning ratio of the video screen is set at 50Hz or 85Hz.
(Do not exceed 60Hz when using the maximum resolution.)
5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove
the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the
computer to reinstall the adapter (video) driver.
Check List
The following table lists possible problems and their solutions. Before calling for service, check the
information in this section to see if you can remedy any problems yourself. If you do need
assistance, please call the phone number on the Information section or contact your dealer.
Problems related to Installation | Problems related to Screen | Problems related to Audio | Problems related
to Remote Control
1. Problems related to Installation
Problems related to the monitor installation and their solutions are listed.
Problems
The monitor screen flickers.
Solutions
z
Check if the signal cable between the computer and the
monitor is securely connected and tightened.
(Refer to Connecting to a Computer)
2. Problems related to Screen
Problems related to the monitor screen and their solutions are listed.
Problems
Solutions
Screen is blank and power
indicator is off
z
"Check Signal Cable" message
z
z
"Not Optimum Mode " message
z
z
Picture rolls vertically.
z
Image is not clear. Picture is
blurred.
z
z
z
Picture image is unstable and
vibrates.
z
Ghost images are shown in the
picture.
The image is too light or too dark
z
Screen color is inconsistent.
z
Ensure that the power cord is firmly connected and the LCD
monitor is on.
(Refer to the Connecting the Monitor)
Ensure that the signal cable is firmly connected to the PC or
video sources.
(Refer to the Connecting the Monitor)
Ensure that the PC or video sources are turned on.
Check the maximum resolution and the frequency of the
video adapter.
Compare these values with the data in the Preset Timing
Modes Chart.
Check if the signal cable is securely connected.
Connect it again securely.
(Refer to Connecting to a Computer)
Run Frequency Coarse and Fine tuning.
Turn on again after removing all accessories
(video extension cable, etc.)
Set resolution and frequency to the recommended ranges.
Check if the resolution and frequency set for the computer
video card falls in the range supported by the monitor.
If not, reset them referring to the current Information under
the monitor menu and Preset Timing Modes.
adjust the brightness and contrast.
(Refer to the Brightness, Contrast)
Adjust color using Custom under OSD Color Adjustment
menu.
Color image is distorted with
dark shadows.
White color is poor.
Power Indicator blinks green.
z
Screen is blank and power
indicator light is steady green or
blinks every 0.5 or 1 seconds
z
The screen is blank and is
blinking.
z
z
The monitor is currently saving the changes made in settings
to the OSD memory.
The monitor is using its power management system.
Press a key on the keyboard.
If you see the "TEST GOOD" message on the screen when
you press the MENU button, check the cable connection
between the monitor and the computer to ensure that the
connector is properly connected.
3. Problems related to Audio
Problems related to audio signals and their solutions are listed below.
Problems
No sound
Solutions
z
z
Sound level is too low.
z
z
Ensure that the audio cable is firmly connected to both the
audio-in port on your monitor and the audio-out port on your
sound card.
(Refer to the Connecting the Monitor)
Check the volume level.
(Refer to the Volume)
Check the volume level.
(Refer to the Volume)
If the volume is still too low after turning the control to its
maximum, check the volume control on the computer sound
card or software program.
Sound is too high pitched or too
low pitched
z
Adjust the Treble and Bass to appropriate level.
4. Problems related to Remote Control
Problems related to the remote control and their solutions are listed.
Problems
Items to check
The remote control buttons do
not respond.
z
z
z
z
z
Check the battery polarities (+/-).
Check if the batteries have been exhausted.
Check if the power is on.
Check if the power cord is securely connected.
Check if a special fluorescent or neon lamp is on in the
vicinity.
Q&A
Question
How can I change the
frequency?
How can I adjust the
resolution?
Answer
Frequency can be changed by reconfiguring the video card.
Note that video card support can vary, depending on the version of
the driver used. (Refer to the computer or the video card manual for
details.)
z
z
How can I set the Power Saving
function?
z
z
How can I clean the outer
case/LCD Panel?
Windows XP :
Set the resolution at the Control Panel→Appearance and
Themes→Display→Settings.
Windows ME/2000 :
Set the resolution at the Control Panel→Display→Settings.
* Contact the video card manufacturer for details.
Windows XP :
Set the resolution at the Control Panel→Appearance and
Themes→Display→Screen Saver .
Set the function at BIOS-SETUP of the computer. (Refer to
Windows/Computer Manual).
Windows ME/2000 :
Set the resolution at the Control Panel→Display→Screen
Saver.
Set the function at BIOS-SETUP of the computer. (Refer to
Windows/Computer Manual).
Disconnect the power cord and then clean the monitor with a soft
cloth, using either a cleaning solution or plain water.
Do not leave any remains of the detergent nor scratch the case. Do
not allow any water to go inside the monitor.
General
General
Model Name
SyncMaster 460Pn
LCD Panel
Size
46" Diagonal
Display area
1018.353mm (H) x 572.544mm (V)
Pixel Pitch
0.7455mm (H) x 0.7455mm (V)
Type
a-si TFT active matrix
Synchronization
Horizontal
30 ~ 70 kHz
Vertical
50 ~ 85 Hz
Display Color
16.7M Colors Colors
Resolution
Optimum resolution
1360 x 768 / 1366 x 768 @ 60Hz depends on graphics card used
Maximum resolution
1360 x 768 @ 60Hz
Input Signal, Terminated
RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB.
0.7Vp-p ±5%, Positive bright, 75 ohms ±10%(Terminated),
Separate H/V sync, TTL level, positive or negative
Maximum Pixel Clock
100 MHz(Analog, Digital)
Power Supply
AC 100 ~ 240 VAC(+/- 10%), 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable, 1.8m
DVI-D to DVI-D connector, detachable, 2.0m
Signal Connectors
D-sub, BNC, DVI-D, YPbPr, S-VHS, VCR
Power Consumption
Less than 310W
Power Saving
Less than 5W
Dimensions (WxHxD)/ Weight
1,102 X 658 X 126.5mm / 43.4 X 25.9 X 5.0 inch / 28kg
1,102 X 715 X 293mm / 43.4 X 28.1 X 11.5 inch (With Stand) - Option / 30kg
1,312 X 715 X 293mm / 51.7 X 28.1 X 11.5 inch (With Speaker, With Stand) - Option / 33kg
VESA Mounting Interface
200mm x 200mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F (10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Audio Characteristics
Audio Input 1
RCA Jack Red(R) White(L), 0.5Vrms (-9dB)
Audio Input 2
RCA Jack Red(R) White(L), 0.5Vrms (-9dB)
PC Audio Input
3.5ØStereo Jack, 0.5Vrms (-9dB)
Frequency
RF: 80Hz ~ 15kHz (at -3dB)
Response
A/V: 80Hz ~ 20kHz (at -3dB)
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will
proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm(one
millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be
bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it
without uneasiness.
z For example, the number of TFT LCD sub pixels that is contained in this product are 3,133,440.
Design and specifications are subject to change without prior notice.
MagicNet - Client
Item
Specification
Remarks
LAN
100Mbps
USB
Keyboard/Mouse, Mass Storage
Device Compatible
USB-applied removable storage can be
supported.
Supporting file system is the only FAT ,
other file systems including NTFS are not
supported from MagicNet.
PCM Audio out
16kHz or more
Photo
Supported File Format : BMP/JPEG
3500x2625 or less
Music
Supported File Format : MP3
Sound bandwidth : 50Hz to 15kHz
SPDIF out
Contents
Movie
z
z
File
MPEG1, MPEG2(PS), DivX 4.x,
DivX 5.x
Max 720 X 480 30 fps
MS Office(Word, Excel, Power Point),
HTML, PDF
MPEG2(MP@ML)
DivX 4.x, DivX 5.x
Some files may not be supported
depending on the format or the version.
Internet Browser
Language
OS
MS Internet Explorer
Not Support Flash, Java Applet, Security
Site
English
Windows CE 5.0
MagicNet - Server Requirement
CPU
RAM
Minimum
P1.8Ghz
256M
Recommended
P3.0Ghz
512M
Ethernet
OS
Application
100M
Windows XP
WMP 9 or later
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by
switching your monitor into a low-power mode when it has not been used for a certain amount of time. The
monitor automatically returns to normal operation when you press a key on the keyboard. For energy
conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The
PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a
software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving
mode
EPA
Power off
(Power Switch)
Power off
(Mechanical Power
S/W)
Power Indicator
Green
Green, Blinking
Black
Black
Power Consumption
Less than 310W
Less than 5W
(Off-mode)
Less than 1W
(at 120Vac)
Less than 0W
Option : SPEAKER L/R(8Ω, 10W), USB Device(Max, 5W is allowed)
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will
be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
49.500
+/+
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
43.269
85.008
36.000
-/-
VESA, 800 x 600
35.156
56.250
36.000
+,-/+,-
Display Mode
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x600
46.875
75.000
49.500
+/+
VESA, 800 x600
53.674
85.000
56.250
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1024 x 768
68.677
85.997
94.500
+/+
VESA, 1280 x 768
47.776
60.000
79.500
-/+
VESA, 1360 x 768
47.712
60.000
85.500
+/+
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of the
Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
General
General
Model Name
SyncMaster 460P
LCD Panel
Size
46" Diagonal
Display area
1018.353mm (H) x 572.544mm (V)
Pixel Pitch
0.7455mm (H) x 0.7455mm (V)
Type
a-si TFT active matrix
Synchronization
Horizontal
30 ~ 70 kHz
Vertical
50 ~ 85 Hz
Display Color
16.7M Colors Colors
Resolution
Optimum resolution
1360 x 768 / 1366 x 768 @ 60Hz depends on graphics card used
Maximum resolution
1360 x 768 @ 60Hz
Input Signal, Terminated
RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB.
0.7Vp-p ±5%, Positive bright, 75 ohms ±10%(Terminated),
Separate H/V sync, TTL level, positive or negative
Maximum Pixel Clock
100 MHz(Analog, Digital)
Power Supply
AC 100 ~ 240 VAC(+/- 10%), 60/50 Hz ± 3Hz
Signal Cable
15pin-to-15pin D-sub cable, detachable, 1.8m
DVI-D to DVI-D connector, detachable, 2.0m
Signal Connectors
D-sub, BNC, DVI-D, YPbPr, S-VHS, VCR
Power Consumption
Less than 300W
Power Saving
Less than 5W
Dimensions (WxHxD)/ Weight
1,102 X 658 X 126.5mm / 43.4 X 25.9 X 5.0 inch / 28kg
1,102 X 715 X 293mm / 43.4 X 28.1 X 11.5 inch (With Stand) - Option / 30kg
1,312 X 715 X 293mm / 51.7 X 28.1 X 11.5 inch (With Speaker, With Stand) - Option / 33kg
VESA Mounting Interface
200mm x 200mm (for use with Specialty(Arm) Mounting hardware.)
Environmental considerations
Operating
Temperature: 50°F ~ 104°F (10°C ~ 40°C)
Humidity: 10% ~ 80%, non-condensing
Storage
Temperature: -4°F ~113°F (-20°C ~ 45°C)
Humidity: 5% ~ 95%, non-condensing
Audio Characteristics
Audio Input 1
RCA Jack Red(R) White(L), 0.5Vrms (-9dB)
Audio Input 2
RCA Jack Red(R) White(L), 0.5Vrms (-9dB)
PC Audio Input
3.5ØStereo Jack, 0.5Vrms (-9dB)
Frequency
RF: 80Hz ~ 15kHz (at -3dB)
Response
A/V: 80Hz ~ 20kHz (at -3dB)
Plug and Play Capability
This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer
systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will
proceed automatically, unless the user wishes to select alternate settings.
Dot Acceptable
TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm(one
millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be
bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it
without uneasiness.
z For example, the number of TFT LCD sub pixels that is contained in this product are 3,133,440.
Design and specifications are subject to change without prior notice.
PowerSaver
This monitor has a built-in power management system called PowerSaver. This system saves energy by
switching your monitor into a low-power mode when it has not been used for a certain amount of time. The
monitor automatically returns to normal operation when you press a key on the keyboard. For energy
conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The
PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a
software utility installed on your computer to set up this feature.
State
Normal Operation
Power saving
mode
EPA
Power off
(Power Switch)
Power off
(Mechanical Power
S/W)
Power Indicator
Green
Green, Blinking
Black
Black
Power Consumption
Less than 300W
Less than 5W
(Off-mode)
Less than 1W
(at 120Vac)
Less than 0W
Option : SPEAKER L/R(8Ω, 10W)
Preset Timing Modes
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will
be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on.
Refer to the video card manual and adjust the screen as follows.
Table 1. Preset Timing Modes
Horizontal
Frequency
(kHz)
Vertical
Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
49.500
+/+
IBM, 640 x 350
31.469
70.086
25.175
+/-
IBM, 640 x 480
31.469
59.940
25.175
-/-
IBM, 720 x 400
31.469
70.087
28.322
-/+
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
43.269
85.008
36.000
-/-
VESA, 800 x 600
35.156
56.250
36.000
+,-/+,-
VESA, 800 x 600
37.879
60.317
40.000
+/+
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x600
46.875
75.000
49.500
+/+
VESA, 800 x600
53.674
85.000
56.250
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1024 x 768
68.677
85.997
94.500
+/+
VESA, 1280 x 768
47.776
60.000
79.500
-/+
VESA, 1360 x 768
47.712
60.000
85.500
+/+
Display Mode
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the
screen horizontally is called Horizontal Cycle and the inverse number of the
Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Vertical Frequency
Like a fluorescent lamp, the screen has to repeat the same image many
times per second to display an image to the user. The frequency of this
repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
Service
The address and phone number of the company can be changed without previous notice.
AUSTRALIA :
Samsung Electronics Australia Pty Ltd.
Customer Response Centre
7 Parkview Drive, Homebush Bay NSW 2127
Tel : 1300 362 603
http://www.samsung.com.au/
BRAZIL :
Samsung Eletronica da Amazonia Ltda.
R. Prof. Manoelito de Ornellas, 303, Terro B
Chacara Sto. Antonio, CEP : 04719-040
Sao Paulo, SP
SAC : 0800 124 421
http://www.samsung.com.br/
CANADA :
Samsung Electronics Canada Inc.
Samsung Customer Care
55 Standish Court
Mississauga, Ontario
L5R 4B2
1-800-SAMSUNG (1-800-726-7864)
http://www.samsung.ca/
CHILE :
SONDA S.A.
Teatinos 550, Santiago Centro, Santiago, Chile
Fono: 56-2-5605000 Fax: 56-2-5605353
56-2-800200211
http://www.sonda.com/
http://www.samsung.cl/
COLOMBIA :
Samsung Electronics Colombia
Cra 9 No 99A-02 Of. 106
Bogota, Colombia
Tel.: 9-800-112-112
Fax: (571) 618 - 2068
http://www.samsung-latin.com/
e-mail : soporte@samsung-latin.com
ESPAÑA :
Samsung Electronics Comercial Iberica, S.A.
Ciencies, 55-65 (Poligono Pedrosa) 08908
Hospitalet de Llobregat (Barcelona)
Tel. : (93) 261 67 00
Fax. : (93) 261 67 50
http://samsung.es/
FRANCE :
SAMSUNG ELECTRONICS FRANCE Service
Paris Nord 2
66 rue des Vanesses
BP 50116 Villepinte
95950 Roissy CDG Cedex
Tel : 08 25 08 65 65
Fax : 01 48 63 06 38
http://www.samsungservices.com/
GERMANY :
TELEPLAN Rhein-Main GmbH
Feldstr. 16
64331 Weiterstadt
T. 06151/957-1306
F. 06151/957-1732
* EURO 0.12/Min
http://www.samsung.de/
HUNGARY :
Samsung Electronics Magyar Rt.
1039, Budapest, Lehel u. 15-17.
Tel: 36 1 453 1100
Fax: 36 1 453 1101
http://www.samsung.hu/
ITALY :
Samsung Electronics Italia S.p.a.
Via C. Donat Cattin, 5
20063 Cernusco s/Naviglio (MI)
Servizio Clienti: 199.153.153
http://www.samsung-italia.com/
MÉXICO :
SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: 01-55-5747-5100 / 01-800-726-7864
Fax: 01-55-5747-5202 / 01-800-849-1743
RFC: SEM950215S98
http://www.samsung.com.mx/
IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V.
Vía Lopez Portillo No. 6, Col. San Fco. Chilpan
Tultitlán, Estado de México, C.P. 54940
Tel: 01-55-5747-5100 / 01-800-726-7864
EXPORTADO POR: Samsung Electronics CO.,LTD.
416, Mae tan-3dong, Yeongtong - gu,
Suwon City, Gyeonggi-do Korea
NETHERLANDS/BELGIUM/LUXEMBOURG :
Samsung Electronics Benelux B. V.
Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS
Service and informatielijn ;
Belgium :0800-95214, http://www.samsung.be/
Netherlands : 0800-2295214, http://www.samsung.nl/
PANAMA :
Samsung Electronics Latinoamerica( Z.L.) S.A.
Calle 50 Edificio Plaza Credicorp, Planta Baja
Panama
Tel. : (507) 210-1122, 210-1133
Tel : 800-3278(FAST)
http://www.samsung-latin.com/
PERU :
Servicio Integral Samsung
Av.Argentina 1790 Lima1. Peru
Tel: 51-1-336-8686
Fax: 51-1-336-8551
http://www.samsungperu.com/
PORTUGAL :
SAMSUNG ELECTRONICA PORTUGUESA S.A.
Rua Mário Dioniso, No2 - 1º Drt. 2795-140 LINDA-A-VELHA
Tel. 214 148 114/100 Fax. 214 148 133/128
Free Line 800 220 120
http://www.samsung.pt/
SOUTH AFRICA :
Samsung Electronics,5 Libertas Road, Somerset Office Park,
Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa
Tel : 0027-11-549-1621
Fax : 0027-11-549-1629
http://www.samsung.co.za/
SWEDEN/DENMARK/NORWAY/FINLAND :
Samsung Electronics Nordic AB
Samsung support Sweden: 08-585 36787
Samsung support Danmark : 38 322 887
Samsung support Norway: 231 62722
Samsung support Finland: 09-69379 554
http://www.samsung.se
http://www.samsung.dk
http://www.samsung.no
http://www.samsung.fi
THAILAND :
HAI SAMSUNG Service Center
MPA COMPLEX BUILDING,1st-2nd Floor
175 SOI SUEKSA VIDHAYA SATHON SOI 12
SILOM ROAD ,SILOM,BANGRAK
BANGKOK 10500
TEL : 0-2635-2567
FAX : 0-2635-2556
UKRAINE :
SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE
4 Glybochitska str.
Kiev, Ukraine
Tel. 8-044-4906878
Fax 8-044-4906887
Toll-free 8-800-502-0000
http://www.samsung.com.ua/
United Kingdom :
Samsung Electronics (UK) Ltd.
Samsung House, 225 Hook Rise South
Surbiton, Surrey KT6 7LD
Tel. : (0208) 391 0168
Fax. : (0208) 397 9949
< European Service Center & National Service >
Stafford Park 12 Telford, Shropshire, TF3 3BJ
Tel. : (0870) 242 0303
Fax. : (01952) 292 033
http://samsungservice.co.uk/
U.S.A :
Samsung Electronics America
Service Division
400 Valley Road, Suite 201
Mount Arlington, NJ 07856
1-800-SAMSUNG (1-800-726-7864)
http://samsung.com/monitor/
Terms
Sync Signal
Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on
the monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal
color images by the set resolution and frequency.
Types of Sync Signals
Separate
This is a scheme of transmitting individual vertical sync signals to the monitor.
Composite
This is a scheme of combining vertical sync signals into one composite signal
and transmitting it to the monitor. The monitor displays the color signals by
separating the composite signal into original color signals.
Dot Pitch
The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the
resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm
Vertical Frequency
The screen must be redrawn several times per second in order to create and display an image for the
user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit: Hz
Example:
If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency
The time to scan one line connecting the right edge to the left edge of the screen horizontally is called
Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz
Interlace and Non-Interlace Methods
Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method.
The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace
method is the same as that used in TVs.
Plug & Play
This is a function that provides the best quality screen for the user by allowing the computer and the
monitor to exchange information automatically. This monitor follows the international standard VESA
DDC for the Plug & Play function.
Resolution
The number of horizontal and vertical dots used to compose the screen image is called 'resolution'.
This number shows the accuracy of the display. High resolution is good for performing multiple tasks as
more image information can be shown on the screen.
Example: If the resolution is 1360 X 768 , this means the screen is composed of 1360 horizontal dots
(horizontal resolution) and 768 vertical lines (vertical resolution).
Multiple Display Control (MDC)
A Multiple Display Control (MDC) is an application allowing various displays to be easily and
simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the
communication between a PC and a display.
For Better Display
1. Adjust computer resolution and screen injection rate (refresh rate) on computer as described below to
enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best
quality of picture is not provided in TFT-LCD.
{
Resolution: 1360 x 768
{
Vertical frequency (refresh rate): 60 Hz
2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm
(one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color
seem to be bright sometimes or some of black pixels could be seen.
This is not from bad quality and you can use it without uneasiness.
{
For example, the number of TFT LCD sub pixels that is contained in this product are 3,133,440
3. When you clean the monitor and the panel outside, please apply the recommended small amount of
cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out
softly.
If excessive force is applied, you can have a stain on it.
4. If you are not satisfied with the quality of picture, you can get better quality of picture by executing
"auto adjustment function" in display screen that is appeared as window termination button is
pressed.
If there's still noise after automatic adjustment, use FINE/COARSE adjustment function.
5. If you view a fixed screen for an extended period of time, residual image or blurriness may appear.
Change the mode to energy save or set a screensaver to moving picture when you need to be away
from the monitor for an extended period of time.
Authority
Information in this document is subject to change without notice.
© 2005 Samsung Electronics Co., Ltd. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is
strictly forbidden.
Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows
NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks
of Video Electronics Standard Association; All other product names mentioned herein may be the
trademarks or registered trademarks of their respective owners.
Class B
This device is a Class B digital apparatus. For Safety and EMC compliance guide, you may refer to
"Regulatory" Guide.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another
especially after displaying a stationary image for a long time.
This guide is to demonstrate correct usage of LCD products in order to protect them from Image
retention.
What is Image retention ?
During normal operation of a LCD panel, pixel image retention doesn't occur. However,
if the same image is displayed for a long time, a slight difference in electric charge
accumulates between the two electrodes which encase the liquid crystal. This may
cause the liquid crystal to build up in a certain areas of the display. Thus, the previous
image is retained when switching to a new video image. All display products, including
LCD,are subject to image retention. This is not a product defect.
Please follow the suggestions below to protect your LCD from image retention
Power Off, Screen Saver, or Power Save Mode
Ex)
z Turn the power off when using a stationary pattern.
- Turn the power off for 4 hours after 24 hours in use
- Turn the power off for 2 hours after 12 hours in use
z Use a Screen saver if possible
- Screen saver in one color or a moving image is recommended.
z Set the Monitor to power off with the PC Display Properties Power Scheme.
Suggestions for specific applications
Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems
We recommend that you follow set up of your display system program as below:
Display Information together with Logo or Moving image cycle.
Ex) Cycle : Display Information for 1 hour followed by a
Display Logo or moving image for 1 minute.
Change the Color Information periodically (Use 2 different colors).
Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large
difference in luminance.
Avoid using Grey colors, which can cause Image retention easily.
Avoid: Colors with big difference in luminance (Black & White, Grey)
Ex)
z
Recommended settings: Bright colors with little difference in luminance
- Change the characters color and background color every 30 minutes
Ex)
z
- Every 30 minutes, change the characters with movement.
Ex)
The best way to protect your monitor from Image retention is to set your PC or
System to operate a Screen Saver program when you are not using it.
Image retention may not occur when a LCD panel is operated under normal conditions.
Normal conditions are defined as continuously changing video patterns. When the LCD
panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be
slight difference in voltage between electrodes that work the liquid crystal (LC) in a
pixel. The voltage difference between electrodes increases with time, forcing the liquid
crystal to lean. When this occurs, the previous image may be seen when the pattern is
changed.
To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicates that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this
product, or their local government office, for details of where and how they
can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract. This product should not be mixed with
other commercial wastes for disposal.
Download PDF