Samsung | DC32E | Samsung DC32E User Manual

User Manual
ED65E ED75E
EM65E EM75E
DC32E DC40E DC48E DC55E
DC32E-M DC40E-M DC48E-M DC55E-M
DC40E-H DC48E-H
The colour and the appearance may differ depending on the product, and the
specifications are subject to change without prior notice to improve the performance.
Recommended hours of use per day for the EDE, EME, DCE models is less than 16 hours.
If the product is used for longer than 16 hours a day, the warranty may be void.
Table of contents
Before Using the Product
Copyright6
Safety Precautions
7
Symbols7
Cleaning7
Storage8
Electricity and Safety
8
Installation9
Operation11
Remote Control (RS232C)
25
Cable Connection
25
Connection28
Control Codes
29
Using MDC
MDC Programme Installation/Uninstallation 47
Installation47
Uninstallation47
Connecting to MDC
Using MDC via RS-232C
(serial data communications standards)
Using MDC via Ethernet
Connecting and Using a Source
Device
48
48
49
Before Connecting
Pre-connection Checkpoints
38
38
Connecting to a PC
Connection using the D-SUB cable
(Analogue type)
Connection using a DVI cable (Digital type)
Connection Using an HDMI-DVI Cable
Connection Using an HDMI Cable
38
Screen Adjustment
38
39
39
40
Picture Mode50
If the input source is PC, DVI, HDMI(PC)50
If the input source is AV, Component, HDMI(AV)50
Connecting to a Video Device
Connection Using the AV Cable
Connection Using the component Cable
Connection Using an HDMI-DVI Cable
Connection Using an HDMI Cable
41
41
41
42
43
Before Installing the Product
(Installation Guide)
22
Switching between portrait and landscape
22
Ventilation22
Connecting to an Audio System
43
Connecting the LAN Cable
44
Connecting the HDBase-T
45
Installing the Wall Mount
Preparing before installing Wall-Mount
Installing the Wall Mount Kit
Wall Mount Kit Specifications (VESA)
Changing the Input source
46
Source46
Preparations
Checking the Components
14
Components14
Parts15
Control Panel
15
Reverse Side
17
Reverse Side
18
Anti-theft Lock
19
Remote Control
20
23
23
23
24
Backlight / Contrast / Brightness / Sharpness /
Colour / Tint (G/R)51
Gamma51
Calibrated value52
Picture Size53
Picture Size53
Position54
Zoom/Position54
Resolution Select55
Auto Adjustment55
PC Screen Adjustment56
PIP57
2
Table of contents
Advanced Settings58
Dynamic Contrast59
Black Tone59
Flesh Tone59
RGB Only Mode59
Colour Space59
White Balance59
Motion Lighting59
Picture Options60
Colour Tone61
Colour Temp.61
Digital Clean View61
MPEG Noise Filter61
HDMI Black Level62
Film Mode62
Motion Plus62
Dynamic Backlight62
Network
System
Network Status67
Setup79
Network Settings67
Network type67
Network Settings (Wired)
68
Network Setting (Wireless)
70
WPS(PBC)72
Menu Language80
Wi-Fi Direct73
AllShare Settings73
Server Network Settings74
Connect to server74
Server Access74
FTP Mode74
Device Name74
Picture Off63
Reset Picture63
Sound Adjustment
Sound Mode64
Sound Effect65
Speaker Settings66
Reset Sound66
Applications
Source List75
Refresh75
Edit Name75
Information75
MagicInfo Lite76
Playing content from the internal memory or
USB76
Network Channel77
Multi Control80
Configuring settings for Multi Control80
Time81
Clock Set81
Sleep Timer81
On Timer81
Off Timer82
Holiday Management82
Eco Solution83
Energy Saving83
Eco Sensor83
No Signal Power Off83
Auto Power Off83
Auto Protection Time84
Screen Burn Protection85
Pixel Shift85
Timer86
Immediate display87
Side Grey87
Ticker88
Video Wall89
Video Wall89
Format89
Horizontal89
3
Table of contents
Vertical90
Screen Position90
Source AutoSwitch Settings91
Source AutoSwitch91
Primary Source Recovery91
Primary Source91
Secondary Source91
Change PIN92
General93
Max. Power Saving93
Game Mode93
Auto Power On93
Safety Lock93
Button Lock94
Standby Control94
HDBT Standby94
Network Standby94
Lamp Schedule95
OSD Display95
Power On Adjustment95
Temperature Control95
DivX® Video On Demand101
PC module power101
Synced power-on101
Synced power-off101
Support
Software Update102
Update now102
Contact Samsung102
Playing photos, videos and music
(Media Play)
Read the following before using media play
with a USB device
103
Using a USB device
105
Menu items in the media content list page
106
Anynet+ (HDMI-CEC)96
Anynet+ (HDMI-CEC)96
Auto Turn Off97
Troubleshooting for Anynet+
98
Available buttons and features during photo
playback107
Clone Product100
Available buttons and features during music
playback109
Reset System100
Reset All101
Subtitle110
Compatible image file format
110
Supported music file formats
111
Supported Video Formats
111
Troubleshooting Guide
Requirements Before Contacting Samsung
Customer Service Centre
Testing the Product
Checking the Resolution and Frequency
Check the followings.
114
114
114
115
Q & A
122
Specifications
General123
Preset Timing Modes
125
Available buttons and features during video
playback108
Supported Subtitle and Media play file
formats110
4
Table of contents
Appendix
Responsibility for the Pay Service
(Cost to Customers)
127
Not a product defect
127
A Product damage caused by customer's fault 127
Others127
Optimum Picture Quality and Afterimage
Burn-in Prevention
Optimum Picture Quality
Prevention of Afterimage Burn-in
128
128
128
Licence130
Terminology131
5
Chapter 01
Before Using the Product
Copyright
The contents of this manual are subject to change without notice to improve quality.
© 2016 Samsung Electronics
Samsung Electronics owns the copyright for this manual.
Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited.
Microsoft, Windows are registered trademarks of Microsoft Corporation.
VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Ownership of all other trademarks is attributed to their due owner.
•• An administration fee may be charged if either
-- (a) an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual).
-- (b) you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
•• The amount of such administration charge will be advised to you before any work or home visit is carried out.
6
Safety Precautions
Cleaning
――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched.
Caution
――Take the following steps when cleaning.
――The following images are for reference only. Real-life situations may differ from what is shown in the
images.
RISK OF ELECTRIC SHOCK DO NOT OPEN
Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. (OR BACK)
THERE ARE NO USER SERVICEABLE PARTS INSIDE.
REFER ALL SERVICING TO QUALIFIED PERSONNEL.
1
Power off the product and computer.
2
Disconnect the power cord from the product.
――Hold the power cable by the plug and do not touch the cable with wet
hands. Otherwise, an electric shock may result.
This symbol indicates that high voltage is present inside.
3
It is dangerous to make any kind of contact with any internal part of this product.
This symbol alerts you that important literature concerning operation and maintenance has been
included with this product.
•• Do not use detergents that contain alcohol, solvent or
surface-active agents.
!
•• Do not spray water or detergent directly on the product.
Symbols
Warning
A serious or fatal injury may result if instructions are not followed.
Wipe the product with a clean, soft and dry cloth.
4
Wet a soft and dry cloth in water and wring thoroughly to clean the
exterior of the product.
Caution
Personal injury or damage to properties may result if instructions are not followed.
Activities marked by this symbol are prohibited.
5
Connect the power cord to the product when cleaning is finished.
6
Power on the product and computer.
Instructions marked by this symbol must be followed.
7
Storage
Connect the power plug to a grounded power socket (type 1 insulated
devices only).
Due to the characteristics of high-glossy products, using a UV humidifier nearby may create
whitecoloured stains on the product.
――Contact Customer Service Centre if the inside of the product needs cleaning (service fee will be
•• An electric shock or injury may result.
!
Do not bend or pull the power cord with force. Be careful not to leave the
power cord under a heavy object.
charged).
Electricity and Safety
•• Damage to the cord may result in a fire or electric shock.
――The following images are for reference only. Real-life situations may differ from what is shown in the
images.
Do not place the power cord or product near heat sources.
•• A fire or electric shock may result.
Warning
Do not use a damaged power cord or plug, or a loose power socket.
•• An electric shock or fire may result.
Clean any dust around the pins of the power plug or the power socket with
a dry cloth.
•• A fire may result.
Do not use multiple products with a single power socket.
•• Overheated power sockets may cause a fire.
!
Do not touch the power plug with wet hands. Otherwise, an electric shock
may result.
Insert the power plug all the way in so it is not loose.
•• An unsecure connection may cause a fire.
!
8
Installation
Caution
Do not disconnect the power cord while the product is being used.
•• The product may become damaged by an electric shock.
Warning
DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF
THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES.
•• A fire may result.
Only use the power cord provided with your product by Samsung. Do not
use the power cord with other products.
•• A fire or electric shock may result.
Have a technician install the wall-mount hanger.
!
•• Installation by an unqualified person can result in an injury.
•• Only use approved cabinets.
Keep the power socket where the power cord is connected unobstructed.
•• The power cord must be disconnected to cut off power to the product
when an issue occurs.
!
!
Do not install the product in poorly ventilated spaces such as a bookcase or
closet.
•• Note that the product is not completely powered down by using only
the power button on the remote.
•• An increased internal temperature may cause a fire.
Hold the plug when disconnecting the power cord from the power socket.
•• An electric shock or fire may result.
Install the product at least 10cm away from the wall to allow ventilation.
•• An increased internal temperature may cause a fire.
!
!
Keep the plastic packaging out of the reach of children.
•• Children may suffocate.
!
9
Do not install the product on an unstable or vibrating surface (insecure shelf,
sloped surface, etc.)
Caution
•• The product may fall and become damaged and/or cause an injury.
Do not drop the product while moving.
•• Using the product in an area with excess vibration may damage the
product or cause a fire.
Do not install the product in a vehicle or a place exposed to dust, moisture
(water drips, etc.), oil, or smoke.
•• Product failure or personal injury may result.
!
Do not set down the product on its front.
•• A fire or electric shock may result.
•• The screen may become damaged.
!
Do not expose the product to direct sunlight, heat, or a hot object such as a
stove.
When installing the product on a cabinet or shelf, make sure that the
bottom edge of the front of the product is not protruding.
•• The product lifespan may be reduced or a fire may result.
•• The product may fall and become damaged and/or cause an injury.
•• Install the product only on cabinets or shelves of the right size.
Do not install the product within the reach of young children.
•• The product may fall and injure children.
Set down the product gently.
•• As the front is heavy, install the product on a flat and stable surface.
Edible oil, such as soybean oil, can damage or deform the product. Do not
install the product in a kitchen or near a kitchen counter.
•• Product failure or personal injury may result.
!
SAMSUNG
!
Installing the product in an unusual place (a place exposed to a lot of fine
dust, chemical substances, extreme temperatures or a significant presence
of moisture, or a place where the product will operate continuously for an
extended period of time) may seriously affect its performance.
•• Be sure to consult Samsung Customer Service Centre if you want to
install the product at such a place.
10
Operation
Do not leave heavy objects or items that children like (toys, sweets, etc.) on
top of the product.
•• The product or heavy objects may fall as children try to reach for the
toys or sweets resulting in a serious injury.
Warning
There is a high voltage inside the product. Never disassemble, repair or
modify the product yourself.
During a lightning or thunderstorm, power off the product and remove the
power cable.
•• A fire or electric shock may result.
•• A fire or electric shock may result.
•• Contact Samsung Customer Service Centre for repairs.
!
Before moving the product, turn off the power switch and disconnect the
power cable and all other connected cables.
Do not drop objects on the product or apply impact.
•• A fire or electric shock may result.
•• Damage to the cord may result in a fire or electric shock.
!
!
If the product generates abnormal sounds, a burning smell or smoke,
disconnect the power cord immediately and contact Samsung Customer
Service Centre.
Do not move the product by pulling the power cord or any cable.
•• Product failure, an electric shock or fire may result from a damaged
cable.
•• An electric shock or fire may result.
!
Do not let children hang from the product or climb on top of it.
If a gas leakage is found, do not touch the product or power plug. Also,
ventilate the area immediately.
•• Children may become injured or seriously harmed.
•• Sparks can cause an explosion or fire.
!
If the product is dropped or the outer case is damaged, turn off the power
switch and disconnect the power cord. Then contact Samsung Customer
Service Centre.
•• Continued use can result in a fire or electric shock.
GAS
Do not lift or move the product by pulling the power cord or any cable.
•• Product failure, an electric shock or fire may result from a damaged
cable.
11
Do not use or keep combustible spray or an inflammable substance near
the product.
Caution
•• An explosion or fire may result.
Leaving the screen fixed on a stationary image for an extended period of
time may cause afterimage burn-in or defective pixels.
!
Ensure the vents are not blocked by tablecloths or curtains.
•• Activate power-saving mode or a moving-picture screen saver if you
will not be using the product for an extended period of time.
!
•• An increased internal temperature may cause a fire.
-_100
Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects
that burn easily (paper, matches, etc) into the product (via the vent or input/
output ports, etc).
•• Dust accumulation combined with heat can cause a fire, electric shock
or electric leakage.
!
Use the product at the recommended resolution and frequency.
•• Be sure to power off the product and disconnect the power cord
when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Centre.
•• Product failure, an electric shock or fire may result.
Disconnect the power cord from the power socket if you do not plan on
using the product for an extended period of time (vacation, etc).
•• Your eyesight may deteriorate.
!
Do not hold the product upside-down or move it by holding the stand.
Do not place objects containing liquid (vases, pots, bottles, etc) or metallic
objects on top of the product.
•• The product may fall and become damaged or cause an injury.
•• Be sure to power off the product and disconnect the power cord
when water or other foreign substances have entered the product.
Then contact Samsung Customer Service Centre.
•• Product failure, an electric shock or fire may result.
Looking at the screen too close for an extended period of time can
deteriorate your eyesight.
!
Do not use humidifiers or stoves around the product.
•• A fire or electric shock may result.
12
Rest your eyes for more than 5 minutes for every 1 hour of product use.
Be careful that children do not place the battery in their mouths when
removed from the remote control. Place the battery in a location that
children or infants cannot reach.
•• Eye fatigue will be relieved.
•• If children have had the battery in their mouths, consult your doctor
immediately.
!
Do not touch the screen when the product has been turned on for an
extended period of time as it will become hot.
When replacing the battery, insert it with the right polarity (+, -).
Store small accessories out of the reach of children.
Use only the specified standardized batteries, and do not use a new battery
and a used battery at the same time.
•• Otherwise, the battery may become damaged or it may cause fire,
personal injury or damage due to leakage of the internal liquid.
•• Otherwise, the batteries may be damaged or cause fire, personal injury
or damage due to a leakage of the internal liquid.
!
!
Exercise caution when adjusting the product angle or stand height.
The batteries (and rechargeable batteries) are not ordinary refuse and must
be returned for recycling purposes. The customer is responsible for returning
the used or rechargeable batteries for recycling.
•• Your hand or finger may get stuck and injured.
!
•• Tilting the product at an excessive angle may cause the product to fall
and an injury may result.
Do not place heavy objects on the product.
!
•• The customer can return used or rechargeable batteries to a nearby
public recycling centre or to a store selling the same type of the
battery or rechargeable battery.
•• Product failure or personal injury may result.
When using headphones or earphones, do not turn the volume too high.
•• Having the sound too loud may damage your hearing.
13
Chapter 02
Preparations
Checking the Components
-- Contact the vendor where you
purchased the product if any
components are missing.
Components
――Components may differ in different locations.
-- The pictures may look different from the
actual components.
-- A stand is not provided with the product.
To install a stand, you can purchase one
separately.
Warranty card
Quick Setup Guide
-- The RS232C adapter can be used to
connect to another monitor using the
D-SUB (9-pin) type RS232C cable.
(Not available in some locations)
Regulatory guide
Power cord
-
-
+
+
Batteries
(Not available in some locations)
Remote Control
D-SUB cable
(EDE and EME Model Only)
RS232C(IN) adapter
Holder-Ring (4EA)
(EDE and EME Model Only)
14
――The colour and shape of parts may differ from what is shown. Specifications are subject to change without notice to
Parts
improve quality.
Buttons
Control Panel
Description
Power on the product.
If you press the
button when the product is turned on, the control menu will be
displayed.
――To exit the OSD menu, press and hold the panel key for at least one second.
Move to the upper or lower menu. You can also adjust the value of an option.
Panel Key
Move to the left or right menu.
――You can adjust the volume by moving the panel key left or right when the control
Speaker
menu is not displayed.
Spacer logo
(Optional)
DC32E DC32E-M
Remote sensor
Do not pull on the spacer logo using force. The logo may tear or break off.
Press a button on the remote control pointing at the sensor on the front of the
product to perform the corresponding function.
――Using other display devices in the same space as the remote control of this
product can cause the other display devices to be inadvertently controlled.
Speaker
Spacer logo
Use the remote control within 7 m to 10 m from the sensor on the product at an angle of 30 from the left and right.
――Store used batteries out of reach of children and recycle.
――Do not use a new and used battery together. Replace both batteries at the same time.
――Remove batteries when the remote control is not to be used for an extended period of time.
Remote sensor
15
――If you press the
button on the panel key when the product is turned on, the
control menu will be displayed.
Buttons
Description
Select the connected input source.
Control menu
Source
EDE / EME
Move the panel key right to select Source
in the control menu. When the list of
input sources is displayed, move the panel key left or right to select the desired input
source. Next, press the panel key.
Display the OSD menu.
Menu
Move the panel key left to select Menu
in the control menu. The OSD control
screen will appear. Move the panel key right to select the desired menu. You can
select a sub-menu item by moving the panel key up, down, left, or right. To change
settings, select the desired menu and press the panel key.
Enter MagicInfo mode.
MagicInfo
Move the panel key up to select MagicInfo
in the control menu.
――DCE, DCE-M, DCE-H models are only supported.
Display Tools.
Return
Tools
DCE / DCE-M / DCE-H
Move the panel key up to select Tools
in the control menu.
――EDE, EME models are only supported.
Power off the product.
Power off
Move the panel key down to select Power off
the panel key.
Return
Exit the control menu.
in the control menu. Next, press
Return
16
Reverse Side
Port
――The colour and shape of parts may differ from what is shown. Specifications are
HDBT IN
Description
Sends the HDMI signal to a connected LAN cable using an HDBaseT transmitter.
――EME models are only supported.
subject to change without notice to improve quality.
――EDE, EME models are only supported.
USB
(5V, 1.5A)
DVI IN / MAGICINFO IN
HDBT IN
Connect to a USB memory device.
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
USB
(5V, 1.5A)
HDMI IN
Connects to a source device using an HDMI cable.
RGB IN
Connects to a source device using a D-SUB cable.
RS232C IN
Connects to MDC using an RS232C adapter.
RS232C OUT
DVI IN /
MAGICINFO IN
HDMI IN
RGB IN
RS232C IN
RS232C OUT
RGB / DVI /
HDMI / AV /
COMPONENT
/ AUDIO IN
AUDIO
OUT COMPONENT IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN
Receives sound from a PC via an audio cable.
AUDIO OUT
Connects to the audio of a source device.
AV IN / COMPONENT IN
Connects to a source device using the AV/Component adapter.
IR / AMBIENT SENSOR IN
Supplies power to the external sensor board or receives the light sensor signal.
IR /
AMBIENT
SENSOR IN
17
Reverse Side
Port
Description
――The colour and shape of parts may differ from what is shown. Specifications are
AUDIO OUT
Connects to the audio of a source device.
subject to change without notice to improve quality.
――DCE, DCE-M, DCE-H models are only supported.
AV IN / COMPONENT IN
Connects to a source device using the AV/Component adapter.
AUDIO IN
Receives sound from a PC via an audio cable.
AUDIO OUT
USB
COMPONENT IN
(5V, 1.5A)
DVI IN / MAGICINFO IN
AUDIO IN
Connect to a USB memory device.
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box
(sold separately).
USB
(5V, 1.5A)
DVI IN /
MAGICINFO IN
HDMI IN 1
HDMI IN 1, HDMI IN 2
Connects to a source device using an HDMI cable.
IR IN
Supplies power to the external sensor board or receives the light sensor signal.
RS232C IN
Connects to MDC using an RS232C adapter.
RGB IN
Connects to a source device using a D-SUB cable.
RJ45
Connects to MDC using a LAN cable.
HDMI IN 2
IR IN
RS232C IN
RGB IN
RJ45
18
Anti-theft Lock
――An anti-theft lock allows you to use the product securely even in public places.
――The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details.
――The following images are for reference only. Real-life situations may differ from what is shown in the images.
To lock an anti-theft locking device:
――Stand: Sold separately
1
Fix the cable of your anti-theft locking device to a heavy object such as a desk.
2
Put one end of the cable through the loop on the other end.
3
Insert the locking device into the anti-theft lock slot at the back of the product.
4
Lock the locking device.
-- An anti-theft locking device can be purchased separately.
-- Refer to the user guide provided with your anti-theft locking device for details.
-- Anti-theft locking devices can be purchased at electronics retailers or online.
19
Remote Control
――Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled.
――A button without a description in the image below is not supported on the product.
POWER
OFF
Power on the product.
.QZ
ABC
DEF
GHI
JKL
MNO
PRS
TUV
WXY
DEL-/--
SYMBOL
1
4
7
Adjust the volume.
Change the input source.
Display or hide the onscreen display menu, or
return to the previous menu.
2
5
8
0
3
6
MENU
SOURCE
HOME
Number buttons
Enter the password in the OSD menu.
-- Remote control button functions may
differ for different products.
9
CH LIST
Mute the sound.
Unmuting the sound: Press MUTE again or press
the volume control(+ VOL -) button.
MUTE
VOL
Power off the product.
CH
MagicInfo
Player I
Use this hotkey to directly access MagicInfo.
The hotkey works if the network box is
connected.
MagicInfo Launch Button.
――DCE, DCE-M, DCE-H models are only
supported.
20
Quickly select frequently used functions.
TOOLS
INFO
Display information about the current input
source.
Move to the upper, lower, left or right menu, or
adjust an option's setting.
Confirm a menu selection.
Return to the previous menu.
RETURN
EXIT
PC
DVI
HDMI
DP
A
B
C
D
UNSET
LOCK
Manually select a connected input source from
PC, DVI, HDMI.
It sets safe lock function.
IR control
SET
Exit the current menu.
Used in Anynet+ mode and multimedia mode.
-- Remote control button functions may
differ for different products.
To place batteries in the remote control
21
Before Installing the Product
(Installation Guide)
To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions.
•• Ensure that an authorized installation company installs the wall mount.
•• Otherwise, it may fall and cause personal injury.
•• Make sure to install the specified wall mount.
Switching between portrait and landscape
――Contact Samsung Customer Service Centre for further details.
•• To use the product vertically (portrait), turn it clockwise so that the LED is pointing down.
Ventilation
Installation on a Perpendicular Wall
A Minimum 40 mm
B Ambient temperature: Under 35 C
A
•• When installing the product on a perpendicular wall, allow at least 40 mm of space between the product and wall surface
for ventilation and ensure that the ambient A temperature is kept below 35 C.
B
Figure 1.1 Side view
22
Figure 1.3 Side view
Installation on an Indented Wall
――Contact Samsung Customer Service Centre for further details.
B
D
D
Plane view
A Minimum 40 mm
B Minimum 70 mm
A
C Minimum 50 mm
D Minimum 50 mm
E Ambient temperature: Under 35 C
――When installing the product on an indented wall, allow at least the space specified above between the product and wall for
ventilation and ensure that the ambient temperature is kept below 35 C.
C
E
Figure 1.2 Side view
Installing the Wall Mount
Preparing before installing Wall-Mount
To install a wall-mount from another manufacturer, use the Holder-Ring(1).
――EDE, EME models are only supported.
Installing the Wall Mount Kit
1
The wall mount kit (sold separately) allows you to mount the product on the wall.
For detailed information on installing the wall mount, see the instructions provided with the wall mount.
We recommend you contact a technician for assistance when installing the wall mount bracket.
Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the
wall mount on your own.
23
Wall Mount Kit Specifications (VESA)
――Install your wall mount on a solid wall perpendicular to the floor. Before
attaching the wall mount to surfaces other than plaster board, please contact
your nearest dealer for additional information.
If you install the product on a slanted wall, it may fall and result in severe
personal injury.
•• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
•• Do not use screws that are longer than the standard length or do not comply with the VESA standard screw
specifications. Screws that are too long may cause damage to the inside of the product.
•• For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ
depending on the wall mount specifications.
•• Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury.
Samsung is not liable for these kinds of accidents.
•• Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the
consumer fails to follow the product installation instructions.
•• Always have two people mount the product on a wall.
•• Standard dimensions for wall mount kits are shown in the table below.
Unit: mm (inches)
Model name
VESA screw hole specs Standard Screw
(A * B) in millimeters
ED65E / ED75E / EM65E / EM75E
/ DC48E / DC55E / DC48E-M /
DC48E-H / DC55E-M
400 x 400 (15.7 x 15.7)
DC32E / DC40E / DC32E-M /
DC40E-M / DC40E-H
200 x 200 (7.9 x 7.9)
M8, L32
Quantity
4
――Do not install your Wall Mount Kit while your product is turned on. It may result in personal injury due to electric shock.
24
Remote Control (RS232C)
•• Pin assignment
1 2 3 4 5
5 4 3 2 1
6 7 8 9
9 8 7 6
Cable Connection
RS232C Cable
Interface
RS232C (9 pins)
Pin
TxD (No.2), RxD (No.3), GND (No.5)
Bit rate
9600 bps
Data bits
8 bit
Parity
None
Stop bit
1 bit
Flow control
None
Maximum length
15 m (only shielded type)
<Male type>
Pin
<Female type>
Signal
1
Detect data carrier
2
Received data
3
Transmitted data
4
Prepare data terminal
5
Signal ground
6
Prepare data set
7
Send request
8
Clear to send
9
Ring indicator
25
LAN Cable (DCE, DCE-M, DCE-H Model Only)
•• RS232C cable
Connector: 9-Pin D-Sub to Stereo Cable
6
•• Pin assignment
3
2
1
1
1 2 3 4 5 6 7 8
-P2-
9
-P1-
5
-P1Male type
-P1-
-P2-
-P2-
Rx
3
----------
1
Tx
STEREO
Tx
2
----------
2
Rx
PLUG
Gnd
5
----------
3
Gnd
(3.5ø)
Pin No
Standard Colour
Signal
1
White and orange
TX+
2
Orange
TX-
3
White and green
RX+
4
Blue
NC
5
White and blue
NC
6
Green
RX-
7
White and brown
NC
8
Brown
NC
26
Cross LAN cable (PC to PC)
•• Connector : RJ45
Direct LAN cable (PC to HUB)
HUB
P1
P2
Signal
P1
P2
Signal
TX+
1
<-------->
3
RX+
RJ45
P2
RJ45
P1
P1
P2
RJ45 MDC
P2
Signal
TX-
2
<-------->
6
RX-
<-------->
1
TX+
RX+
3
<-------->
1
TX+
2
<-------->
2
TX-
RX-
6
<-------->
2
TX-
RX+
3
<-------->
3
RX+
RX-
6
<-------->
6
RX-
Signal
P1
TX+
1
TX-
27
Connection
•• Connection 2 (DCE / DCE-M / DCE-H Model)
――Ensure you connect each of the adapters to the correct RS232C IN or OUT port on the product.
•• Connection 1 (EDE / EME Model)
RJ45
IN
RS232C
OUT
IN
RS232C
OUT
IN
RS232C
OUT
IN
RS232C
RJ45
OUT
•• Connection 3 (DCE / DCE-M / DCE-H Model)
RS232C
IN
28
No.
Control Codes
Viewing control state (Get control command)
Header
Command
0xAA
Command type
ID
Data length
Command
0xAA
Command type
Command type
10
Video Wall On
0x84
0~1
11
Video Wall User Control
0x89
-
E.g. Power On & ID=0
Data length
Data
1
Value
Checksum
Command
No.
Value range
•• All communications take place in hexadecimals. The checksum is calculated by adding up all
values except the header. If a checksum adds up to be more than 2 digits as shown below
(11+FF+01+01=112), the first digit is removed.
0
ID
Command
Checksum
Controlling (Set control command)
Header
Command type
Command
Value range
1
Power control
0x11
0~1
2
Volume control
0x12
0~100
3
Input source control
0x14
-
4
Screen mode control
0x18
-
5
Screen size control
0x19
0~255
6
PIP on/off control
0x3C
0~1
7
Auto adjustment control (PC and
BNC only)
0x3D
0
8
Video wall mode control
0x5C
0~1
9
Safety Lock
0x5D
0~1
Header
Command
0xAA
0x11
Header
Command
0xAA
0x11
ID
ID
Data length
Data 1
1
"Power"
Data length
Data 1
1
1
Checksum
12
•• To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID as
"0xFE" and transmit commands. Commands will be executed by each device but ACK will not
respond.
29
Power control
Volume control
•• Function
A product can be powered on and off using a PC.
•• Function
The volume of a product can be adjusted using a PC.
•• Viewing power state (Get Power ON / OFF Status)
•• Viewing volume state (Get Volume Status)
Header
Command
0xAA
0x11
ID
Data length
Checksum
0
•• Setting power ON/Off (Set Power ON / OFF)
Header
Command
0xAA
0x11
ID
Header
Command
0xAA
0x12
Data length
Data
1
"Power"
Checksum
Header
Command
0xAA
0x12
•• Ack
0: Power OFF
Header
Command
0xAA
0xFF
•• Ack
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x11
"Power"
Checksum
0xAA
0xFF
ID
ID
Data length
Data
1
"Volume"
Checksum
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x11
"ERR"
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x12
"Volume"
Checksum
•• Nak
•• Nak
Command
0
"Volume": Volume value code to be set on a product. (0-100)
"Power": Power code to be set on a product.
Header
Checksum
"Volume": Volume value code to be set on a product. (0-100)
1: Power ON
Command
Data length
•• Setting the volume (Set Volume)
"Power": Power code to be set on a product.
Header
ID
Checksum
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x12
"ERR"
Checksum
"ERR" : A code showing what error has occurred.
"ERR" : A code showing what error has occurred.
30
Input source control
0x24
HDMI2_PC
•• Function
The input source of a product can be changed using a PC.
0x55
HDBT
――DVI_video, HDMI1_PC(HDMI_PC) and HDMI2_PC cannot be used with the Set command. They only
•• Viewing input source state (Get Input Source Status)
Header
Command
0xAA
0x14
ID
Data length
respond to "Get" commands.
――Available input sources may vary depending on the model.
Checksum
――MagicInfo is only available with models that contain the MagicInfo function.
0
――RF(TV), DTV are only available with models that include a TV.
•• Setting the input source (Set Input Source)
Header
Command
0xAA
0x14
ID
•• Ack
Data length
Data
1
"Input Source"
Checksum
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x14
"Input
Source"
"Input Source": An input source code to be set on a product.
0x14
PC
0x18
DVI
0x0C
Input source
0x08
Component
0x20
MagicInfo
0x1F
DVI_video
0x30
RF(TV)
0x40
DTV
0x21
HDMI1(HDMI)
0x22
HDMI1_PC(HDMI_PC)
0x23
HDMI2
Checksum
"Input Source": An input source code to be set on a product.
•• Nak
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x14
"ERR"
Checksum
"ERR" : A code showing what error has occurred.
31
Screen mode control
•• Nak
•• Function
The screen mode of a product can be changed using a PC.
Screen mode cannot be controlled when the Video Wall function is enabled.
――This control can only be used on models that include a TV.
Command
0xAA
0x18
ID
Data length
0xAA
ID
0x18
16 : 9
0x04
Zoom
0x31
Wide Zoom
0x0B
4:3
Ack/Nak
r-CMD
Val1
3
'N'
0x18
"ERR"
Checksum
•• Viewing the screen size (Get Screen Size Status)
Data
length
Data
Checksum
1
"Screen Mode"
Header
Command
0xAA
0x19
ID
Data length
Checksum
0
•• Ack
"Screen Mode": A code that sets the product status
0x01
0xFF
Data length
•• Function
The screen size of a product can be changed using a PC.
0
Command
0xAA
ID
Screen size control
Checksum
•• Setting the picture size (Set Picture Size)
Header
Command
"ERR": A code showing what error has occurred
•• Viewing screen status (Get Screen Mode Status)
Header
Header
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x19
"Screen Size"
Checksum
"Screen Size": product screen size (range: 0 – 255, unit: inch)
•• Nak
Header
Command
0xAA
0xFF
•• Ack
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x18
"Screen
Mode"
Checksum
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'N'
0x19
"ERR"
Checksum
"ERR": A code showing what error has occurred
"Screen Mode": A code that sets the product status
32
PIP On/Off control
Auto adjustment control (PC and BNC only)
•• Function
The PIP mode of a product can be turned on or off using a PC.
•• Function
Automatically adjust the PC system screen using a PC.
――Only available on models that have the PIP function.
――The mode cannot be controlled if Video Wall is set to On.
•• Viewing auto adjustment state (Get Auto Adjustment Status)
None
――This function is not available in MagicInfo.
•• Setting auto adjustment (Set Auto Adjustment)
•• Viewing PIP on/off state (Get the PIP ON / OFF Status)
Header
Command
0xAA
0x3C
ID
Data length
Checksum
Command
0xAA
0x3C
Command
0xAA
0x3D
ID
Data length
Data
1
"Auto
Adjustment"
0
ID
Checksum
"Auto Adjustment" : 0x00 (at all times)
•• Setting PIP on/off (Set the PIP ON / OFF)
Header
Header
Data length
Data
1
"PIP"
•• Ack
Checksum
"PIP": A code used to turn the PIP mode of a product on or off
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x3D
"Auto
Adjustment"
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x3D
"ERR"
1: PIP ON
0: PIP OFF
Checksum
•• Nak
•• Ack
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x3C
"PIP"
Checksum
Header
Command
0xAA
0xFF
ID
Checksum
"ERR": A code showing what error has occurred
"PIP": A code used to turn the PIP mode of a product on or off
•• Nak
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x3C
"PIP"
Checksum
"ERR": A code showing what error has occurred
33
Video Wall Mode Control
Safety Lock
•• Function
Video Wall mode can be activated on a product using a PC.
•• Function
PC can be used to turn the Safety Lock function on or off on a product.
This control is only available on a product whose Video Wall is enabled.
This control is available regardless of whether or not the power is turned on.
•• Viewing video wall mode (Get Video Wall Mode)
Header
Command
0xAA
0x5C
ID
Data length
•• Viewing the safety lock state (Get Safety Lock Status)
Checksum
0
•• Setting the video wall (Set Video Wall Mode)
Header
Command
0xAA
0x5C
ID
Header
Command
0xAA
0x5D
ID
Data length
Checksum
0
•• Enabling or disabling safety lock (Set Safety Lock Enable / Disable)
Data length
Data
Checksum
1
"Video Wall Mode"
Header
Command
0xAA
0x5D
ID
Data length
Data
1
"Safety Lock"
"Video Wall Mode": A code used to activate Video Wall mode on a product
"Safety Lock": Safety lock code to be set on a product
1: Full
1: ON
0: Natural
0: OFF
Checksum
•• Ack
•• Ack
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x5C
"Video Wall
Mode"
Checksum
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x5D
"Safety Lock"
Checksum
"Safety Lock": Safety lock code to be set on a product
"Video Wall Mode": A code used to activate Video Wall mode on a product
•• Nak
•• Nak
Header
Command
0xAA
0xFF
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'A'
0x5C
"ERR"
Header
Command
0xAA
0xFF
Checksum
ID
Data
length
Ack/Nak
r-CMD
Val1
3
'N'
0x5D
"ERR"
Checksum
"ERR": A code showing what error has occurred
"ERR": A code showing what error has occurred
34
Video Wall On
•• Nak
•• Function
Turn Video Wall on or off on the product from your computer.
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x84
ERR
Checksum
•• Get Video Wall On/Off Status
Header
Command
0xAA
0x84
ID
Data length
"ERR": A code showing what error has occurred
Checksum
Video Wall User Control
0
•• Function
Turn the Video Wall function on or off on the product from your computer.
•• Set Video Wall On/Off
Header
Command
0xAA
0x84
ID
Data length
Data
Checksum
1
V.Wall_On
•• Get Video Wall Status
•• V.Wall_On: Video Wall code to be assigned to the product
1: Video Wall ON
•• Ack
Command
0xAA
0xFF
Command
0xAA
0x89
ID
Data length
Checksum
0
•• Set Video Wall
0: Video Wall OFF
Header
Header
ID
Data length
Ack/Nak
r-CMD
Val1
3
'A'
0x84
V.Wall_
On
Checksum
Header
Command
0xAA
0x89
ID
Data length
Val1
Val2
2
Wall_Div
Wall_SNo
Checksum
Wall_Div: Video Wall Divider code assigned to the product
V.Wall_On : Same as above
35
10x10 Video Wall Model
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Off
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
1
0x11
0x12
0x13
0x14
0x15
0x16
0x17
0x18
0x19
0x1A
0x1B
0x1C
0x1D
0x1E
0x1F
2
0x21
0x22
0x23
0x24
0x25
0x26
0x27
0x28
0x29
0x2A
0x2B
0x2C
0x2D
0x2E
0x2F
3
0x31
0x32
0x33
0x34
0x35
0x36
0x37
0x38
0x39
0x3A
0x3B
0x3C
0x3D
0x3E
0x3F
4
0x41
0x42
0x43
0x44
0x45
0x46
0x47
0x48
0x49
0x4A
0x4B
0x4C
0x4D
0x4E
0x4F
5
0x51
0x52
0x53
0x54
0x55
0x56
0x57
0x58
0x59
0x5A
0x5B
0x5C
0x5D
0x5E
0x5F
6
0x61
0x62
0x63
0x64
0x65
0x66
0x67
0x68
0x69
0x6A
0x6B
0x6C
0x6D
0x6E
0x6F
7
0x71
0x72
0x73
0x74
0x75
0x76
0x77
0x78
0x79
0x7A
0x7B
0x7C
0x7D
0x7E
N/A
8
0x81
0x82
0x83
0x84
0x85
0x86
0x87
0x88
0x89
0x8A
0x8B
0x8C
N/A
N/A
N/A
9
0x91
0x92
0x93
0x94
0x95
0x96
0x97
0x98
0x99
0x9A
0x9B
N/A
N/A
N/A
N/A
10
0xA1
0xA2
0xA3
0xA4
0xA5
0xA6
0xA7
0xA8
0xA9
0xAA
N/A
N/A
N/A
N/A
N/A
11
0xB1
0xB2
0xB3
0xB4
0xB5
0xB6
0xB7
0xB8
0xB9
N/A
N/A
N/A
N/A
N/A
N/A
12
0xC1
0xC2
0xC3
0xC4
0xC5
0xC6
0xC7
0xC8
N/A
N/A
N/A
N/A
N/A
N/A
N/A
13
0xD1
0xD2
0xD3
0xD4
0xD5
0xD6
0xD7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
14
0xE1
0xE2
0xE3
0xE4
0xE5
0xE6
0xE7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
15
0xF1
0xF2
0xF3
0xF4
0xF5
0xF6
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
36
Wall_SNo: Product Number code assigned to the product
10x10 Video Wall Model : ( 1 ~ 100)
Set Number
Data
1
0x01
2
0x02
...
...
99
0x63
100
0x64
•• Ack
Header
Command
0xAA
0xFF
ID
Data length
Ack/Nak
r-CMD
Val1
Val2
4
'A'
0x89
Wall_Div
Wall_SNo
Data length
Ack/Nak
r-CMD
Val1
3
'N'
0x89
ERR
Checksum
•• Nak
Header
Command
0xAA
0xFF
ID
Checksum
"ERR": A code showing what error has occurred
37
Chapter 03
Connecting and Using a Source Device
Before Connecting
Connecting to a PC
Check the following before you connect this product with other devices. Devices that can be connected
to this product include PCs, camcorders, speakers, set top boxes and DVD/Blu-ray Disc players.
•• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
Pre-connection Checkpoints
•• A PC can be connected to the product in a variety of ways.
Select a connection method suitable for your PC.
――Before connecting a source device, read the user manual provided with it.
The number and locations of ports on source devices may differ from device to device.
――Do not connect the power cable until all connections are completed.
――Connecting parts may differ in different products.
Connection using the D-SUB cable (Analogue type)
Connecting the power cable during connection may damage the product.
――Connect the sound ports correctly: left = white and right = red.
――Check the types of ports at the back of the product you want to connect.
RGB IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
38
Connection using a DVI cable (Digital type)
Connection Using an HDMI-DVI Cable
――When you connect a PC to the product using an HDMI-DVI cable, set Edit Name to DVI PC to access
video and audio content stored on the PC.
DVI IN /
MAGICINFO IN
HDMI IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
――You can use the DVI port on the product as an HDMI port by using a DVI-HDMI adapter.
HDMI
DVI IN /
MAGICINFO IN
39
Connection Using an HDMI Cable
HDMI IN
40
Connecting to a Video Device
•• Do not connect the power cable before connecting all other cables.
Ensure you connect a source device first before connecting the power cable.
•• You can connect a video device to the product using a cable.
――Connecting parts may differ in different products.
――Press the SOURCE button on the remote control to change the source.
Connection Using the AV Cable
Connection Using the component Cable
AV IN / COMPONENT IN
AV IN / COMPONENT IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
41
Connection Using an HDMI-DVI Cable
――Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device. When you
connect a video device to the product using an HDMI-DVI cable, set Edit Name to DVI Devices to access video and audio content stored on the video device.
――Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
DVI IN /
MAGICINFO IN
HDMI
HDMI IN
RGB / DVI / HDMI / AV / COMPONENT /
AUDIO IN or AUDIO IN
42
Connection Using an HDMI Cable
Connecting to an Audio System
Using an HDMI cable or HDMI to DVI Cable (up to 1080p)
――Connecting parts may differ in different products.
•• For better picture and audio quality, connect to a digital device using an HDMI cable.
•• An HDMI cable supports digital video and audio signals, and does not require an audio cable.
-- To connect the product to a digital device that does not support HDMI output, use an HDMIDVI and audio cables.
•• The picture may not display normally (if at all) or the audio may not work if an external device that
uses an older version of HDMI mode is connected to the product. If such a problem occurs, ask
the manufacturer of the external device about the HDMI version and, if out of date, request an
upgrade.
•• Be sure to use an HDMI cable with a thickness of 14 mm or less.
AUDIO OUT
•• Be sure to purchase a certified HDMI cable. Otherwise, the picture may not display or a connection
error may occur.
•• A basic high-speed HDMI cable or one with ethernet is recommended.
This product does not support the ethernet function via HDMI.
HDMI IN
43
Connecting the LAN Cable
――DCE, DCE-M, DCE-H models are only supported.
――Connecting parts may differ in different products.
RJ45
•• Use Cat7(*STP Type) cable for the connection.
*Shielded Twist Pair
44
Connecting the HDBase-T
――EME models are only supported.
――Connecting parts may differ in different products.
――HDBase-T (Tx) transmits data from an external device to HDBase-T (Rx). Make sure to connect them directly using a LAN cable.
――Data transmission is not available if HDBase-T (Rx) is connected to HDBase-T (Tx) through a hub.
――HDBase-T works with unshielded twisted pair (UTP) or shielded twisted pair (STP) cables; but, to ensure CE compliance, STP cables and STP Connectors are required.
Shielded cable and connectors are recommended to safeguard against unpredictable environmental electrical noise which may impact performance.
It is recommended to use an STP cable to maximize performance. Using a UTP cable or patch may decrease performance.
HDMI OUT
HDBase-T (Rx)
HDBase-T (Tx)
HDBT IN
LAN
HDMI IN
HDMI OUT
LAN Cable
HDMI OUT
45
Changing the Input source
Source allows you to select a variety of sources and change source device names.
Source
――The screen may not display correctly if an incorrect source is selected for the source device you want to convert to.
You can display the screen of a source device connected to the product. Select a source from source list to display the screen
of the selected source.
――The input source can also be changed by using the SOURCE button on the remote control.
MENU m → Applications → Source List → ENTER E
Source
HDMI
HDMI-CEC
DVD Player
AV
Component
PC
DVI
-- The displayed image may differ depending on the model.
46
Chapter 04
Using MDC
Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC.
- For details on how to use the MDC programme, refer to Help after installing the programme. The MDC programme is available on the website.
MDC Programme Installation/Uninstallation
Installation
――MDC installation can be affected by the graphics card, mother board and network conditions.
1
Click the MDC Unified installation programme.
2
Select a language for installation. Next, click "OK".
3
When the "Welcome to the InstallShield Wizard for MDC_Unified" screen appears, click "Next".
4
In the "License Agreement" window displayed, select "I accept the terms in the license
5
In the displayed "Ready to Install the Program" window, check the directory path to install the
programme in and click "Install".
8
Installation progress will be displayed.
9
Click "Finish" in the displayed "InstallShield Wizard Complete" window.
――Select "Launch MDC Unified" and click "Finish" to run the MDC programme immediately.
10The MDC Unified shortcut icon will be created on the desktop after installation.
――The MDC execution icon may not be displayed depending on the PC system or product
specifications.
――Press F5 if the execution icon is not displayed.
agreement" and click "Next".
Uninstallation
In the displayed "Customer Information" window, fill out all the information fields and click
1
Select Settings > Control Panel on the Start menu and double-click Add/Delete Program.
2
Select MDC Unified from the list and click Change/Remove.
"Next".
6
7
In the displayed "Destination Folder" window, select the directory path you want to install the
programme in and click "Next".
――If the directory path is not specified, the programme will be installed in the default directory
path.
47
Connecting to MDC
Using MDC via RS-232C (serial data communications standards)
An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
――EDE, EME models are only supported.
Monitor 1
RS232C IN RS232C OUT
Monitor 2
Computer
48
Using MDC via Ethernet
Enter the IP for the primary display device and connect the device to the PC. Display devices can be connected to each other using a LAN cable.
Connection using a direct LAN cable
――Multiple products can be connected using the RJ45 port on the product and the LAN ports on the HUB.
――DCE, DCE-M, DCE-H models are only supported.
Computer
RJ45
HUB
Monitor 1
Monitor 2
49
Chapter 05
Screen Adjustment
Configure the Picture settings (Backlight, Colour Tone, etc.).
The layout of the Picture menu options may vary depending on the product.
Picture Mode
Select a picture mode (Picture Mode) suitable for the environment where the product will be used.
MENU m → Picture → Picture Mode → ENTER E
If the input source is PC, DVI, HDMI(PC)
Different Picture Mode options are displayed depending on the current input source.
•• Information: This mode reduces eye fatigue and is suitable for displaying information to the public.
Picture
•• Advertisement: This mode is suitable for displaying video content and indoor/outdoor advertisements.
Picture Mode
Information
· Backlight
100
100
· Contrast
100
100
· Brightness
45
45
· Sharpness
50
50
· Colour
50
50
· Tint (G/R)
G50
50
-- The displayed image may differ depending on the model.
R50
50
•• Calibration: In this mode, the brightness, colour, gamma and uniformity settings customized using the colour calibration
program Advanced Color Management are applied.
-- To apply the Calibration mode properly, make sure you configure the picture quality settings, such as brightness,
colour, gamma and uniformity, using the colour calibration programme Advanced Color Management.
-- To download the Advanced Color Management programme, visit www.samsung.com/displaysolutions.
If the input source is AV, Component, HDMI(AV)
•• Dynamic: This mode is suitable when the ambient light is bright.
•• Standard: This mode is generally suitable for any environment.
•• Movie: This mode reduces eye fatigue.
•• Calibration: In this mode, the brightness, colour, gamma and uniformity settings customized using the colour calibration
program Advanced Color Management are applied.
-- To apply the Calibration mode properly, make sure you configure the picture quality settings, such as brightness,
colour, gamma and uniformity, using the colour calibration programme Advanced Color Management.
-- To download the Advanced Color Management programme, visit www.samsung.com/displaysolutions.
-- Calibration is only available on the DCE-M, DCE-H models.
50
Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)
MENU m → Picture → ENTER E
Picture
Picture Mode
Information
· Backlight
100
100
· Contrast
100
100
· Brightness
45
45
· Sharpness
50
50
· Colour
50
50
· Tint (G/R)
G50
50
Your product has several options for adjusting picture quality.
Input source
PC, DVI, HDMI, HDBT (when a PC is
connected)
AV, Component, HDMI, HDBT (720p,
1080i, 1080p)
Picture Mode
Adjustable options
Information / Advertisement
Backlight / Contrast / Brightness /
Sharpness
Calibration
Backlight
Dynamic / Standard / Movie
Backlight / Contrast / Brightness /
Sharpness / Colour / Tint (G/R)
Calibration
Backlight
――When you make changes to Backlight, Contrast, Brightness, Sharpness, Colour or Tint (G/R), the OSD will be adjusted
accordingly.
――You can adjust and store settings for each external device you have connected to an input on the product.
――Lowering picture brightness reduces power consumption.
R50
50
-- The displayed image may differ depending on the model.
Gamma
Adjust the primary colour intensity.
――If Picture Mode is set to Calibration, Gamma is disabled.
MENU m → Picture → Gamma → ENTER E
Gamma
0
-- The displayed image may differ depending on the model.
51
Calibrated value
Select whether to apply the brightness, colour, gamma and uniformity settings customized using the colour calibration
programme Advanced Color Management to the Information and Advertisement modes.
MENU m → Picture → Calibrated value → ENTER E
•• Don't apply / Apply
――To download the Advanced Color Management programme, visit www.samsung.com/displaysolutions.
――If Picture Mode is set to Calibration, Calibrated value is disabled.
Picture
Calibrated value
――DCE-M, DCE-H models are only supported.
Don't apply
-- The displayed image may differ depending on the model.
52
Picture Size
Picture Size
MENU m → Picture → Picture Size → ENTER E
If you have a cable box or satellite receiver, it may have its own set of screen sizes as well. However, we highly recommend you
use your product’s 16:9 mode most of the time.
――Different screen adjustment options are displayed depending on the current input source.
•• 16:9: Sets the picture to 16:9 wide mode.
Picture Size
Picture Size
•• Zoom1: Use for moderate magnification. Cuts off the top and sides.
16:9
•• Smart View 1: Reduces the 16:9 picture by 50%.
――Smart View 1 is enabled only in HDMI mode.
· Position
Resolution Select
-- The displayed image may differ depending on the model.
•• Zoom2: Use for a stronger magnification.
Off
•• Smart View 2: Reduces the 16:9 picture by 25%.
――Smart View 2 is enabled only in HDMI mode.
•• 4:3: Sets the picture to basic (4:3) mode.
――Do not set your product to 4:3 format for a long time.
The borders displayed on the left and right, or top and bottom of the screen may cause image retention (screen burn)
which is not covered by the warranty.
•• Screen Fit: Displays the full image without any cut-off when HDMI (720p / 1080i / 1080p) or Component (1080i / 1080p)
signals are inputted.
•• Custom: Changes the resolution to suit the user's preferences.
•• Original ratio: If the input source is PC, DVI, HDMI (PC connection) the video will display in the original aspect ratio.
――Available ports may differ depending on the model.
――You can adjust and store settings for each external device you have connected to an input on the product.
53
Position
Adjusts the picture position. Position is only available if Picture Size is set to Zoom1, Zoom2, Screen Fit.
――To use the Position function after selecting Zoom1, Zoom2 or Screen Fit follow these steps.
Picture Size
Picture Size
Zoom1
· Position
Resolution Select
1
Press the d button to select Position. Press the E button.
2
Press the u or d button to move the picture up or down.
3
Press the E button.
Off
-- The displayed image may differ depending on the model.
――To use the Zoom/Position function after selecting Custom in HDMI (1080i/1080p) or Component (1080i/1080p) or
Zoom/Position
Custom, follow these steps.
Picture Size
Picture Size
Custom
· Zoom/Position
Resolution Select
Off
1
Press the d button to select Zoom/Position. Press the E button.
2
Select the Zoom or Position. Press the E button.
3
Press the u/d/l/r button to move the picture.
4
Press the E button.
――If you want to reset the picture to its original position, select Reset in the Zoom/Position screen.
The picture will be set to its default position.
-- The displayed image may differ depending on the model.
54
Resolution Select
If the picture is not normal even when the resolution of the graphics card is one of the following, you can optimize the picture
quality by selecting the same resolution for the product as the PC using this menu.
Available resolutions: Off / 1024x768 / 1280x768 / 1360x768 / 1366x768
Picture Size
Picture Size
16:9
· Position
Resolution Select
Off
-- Available in PC mode only.
-- The displayed image may differ depending on the model.
Auto Adjustment
Adjust frequency values/positions and fine tune the settings automatically.
MENU m → Picture → Auto Adjustment → ENTER E
Picture
Auto Adjustment
-- Available in PC mode only.
-- The displayed image may differ depending on the model.
55
PC Screen Adjustment
•• Coarse / Fine
Removes or reduces picture noise.
MENU m → Picture → PC Screen Adjustment → ENTER E
•• Position
To adjust the PC’s screen position if it is not centred or does not fit the product screen.
PC Screen Adjustment
Coarse
Fine
If the noise is not removed by Fine-tuning alone, use the Coarse function to adjust the frequency as best as possible
(Coarse) and Fine-tune again. After the noise has been reduced, re-adjust the picture so that it is aligned with the centre
of screen.
50
0
Press the u or d button to adjust the Vertical Position. Press the l or r button to adjust the Horizontal Position.
•• Image Reset
Resets the image to the default settings.
Position
Image Reset
-- Available in PC mode only.
-- The displayed image may differ depending on the model.
56
PIP
MENU m → Picture → PIP → ENTER E
PIP Settings
The picture from the external video source will be in the main screen and the picture from the product will be in the PIP subpicture screen.
Main picture
Picture
PIP
Sub picture
AV
PC, DVI, HDMI, MagicInfo, HDBT
Component
DVI, HDMI, MagicInfo, HDBT
PC
AV, HDMI, MagicInfo, HDBT
DVI, HDMI
AV, Component, PC
HDBT
PC, AV, Component
-- The displayed image may differ depending on the model.
-- For PIP sound, refer to the Sound Select instructions.
-- If you turn the product off while watching in the PIP mode, the PIP function is reset to off.
When you turn your product on, you must turn PIP on again to watch in the PIP mode.
-- You may notice that the picture in the PIP screen becomes slightly unnatural when you use
the main screen to view a game or karaoke.
――Available input sources may vary depending on the model.
•• PIP (Off / On): Activate or deactivate the PIP function.
•• Source: You can select a source of the sub picture.
•• Size (
,
•• Position (
――In (
,
,
,
,
,
,
): Select a size for the subpicture.
,
,
): Select a position for the sub-picture.
,
) mode, you cannot select Position.
•• Sound Select (Main / Sub): You can choose to listen to the sound from the Main picture or the Sub picture.
57
Advanced Settings
Input Source
MENU m → Picture → Advanced Settings → ENTER E
Advanced Settings
Dynamic Contrast
Medium
Black Tone
Off
Flesh Tone
0
RGB Only Mode
Colour Space
PC, DVI, HDMI, MagicInfo,
HDBT (when a PC is connected)
Picture Mode
Information
White Balance
Advertisement
White Balance
AV, Component, DVI, HDMI,
HDBT
Dynamic
Not available
AV, Component, DVI, HDMI,
HDBT
Standard
Dynamic Contrast / Black Tone / Flesh Tone /
RGB Only Mode / Colour Space / White Balance /
Motion Lighting
Movie
Dynamic Contrast / Black Tone / Flesh Tone /
RGB Only Mode / Colour Space / White Balance
Off
Native
Advanced Settings
――Available input sources may vary depending on the model.
――If Picture Mode is set to Calibration, Advanced Settings is disabled.
White Balance
Motion Lighting
Off
-- The displayed image may differ depending on the model.
58
Dynamic Contrast
Advanced Settings
Adjust the screen contrast.
Dynamic Contrast
Medium
Black Tone
Off
Flesh Tone
0
Off
RGB Only Mode
Colour Space
Native
White Balance
Motion Lighting
-- The displayed image may differ depending on the model.
•• Off / Low / Medium / High
Black Tone
Select the black level to adjust the screen depth.
•• Off / Dark / Darker / Darkest
Flesh Tone
Emphasize pink Flesh Tone.
Off
RGB Only Mode
Displays the Red, Green and Blue colour for making fine adjustments to the hue and saturation.
•• Off / Red / Green / Blue
Colour Space
Adjusts the range and variety of colours (the colour space) available to create images.
•• Auto / Native
White Balance
Adjust the colour temperature for a more natural picture.
•• R-Offset / G-Offset / B-Offset: Adjust each colour’s (red, green, blue) darkness.
•• R-Gain / G-Gain / B-Gain: Adjust each colour’s (red, green, blue) brightness.
•• Reset: Resets the White Balance to its default settings.
Motion Lighting
Reduces power consumption by reducing screen brightness when the picture on the screen is in motion.
•• Off / On
59
Picture Options
Select an option using the u and d arrow keys, and the press E.
MENU m → Picture → Picture Options → ENTER E
Input source
Use the arrow keys to change the setting, and then press E.
PC
Picture Options
Colour Tone
Standard
Colour Temp.
10000K
Digital Clean View
Off
MPEG Noise Filter
Off
HDMI Black Level
Normal
Film Mode
Off
Motion Plus
Off
-- The displayed image may differ depending on the model.
-- Motion Plus is only available on the EDE, EME models.
DVI, HDMI, MagicInfo, HDBT
(when a PC is connected)
AV, Component, DVI, HDMI,
HDBT
Picture Mode
Picture Options
Information
Colour Tone / Colour Temp. / Dynamic Backlight
Advertisement
Colour Tone / Colour Temp. / Dynamic Backlight
Calibration
Dynamic Backlight
Information
Colour Tone / Colour Temp. / HDMI Black Level /
Dynamic Backlight
Advertisement
Colour Tone / Colour Temp. / HDMI Black Level /
Dynamic Backlight
Calibration
HDMI Black Level / Dynamic Backlight
Dynamic / Standard / Movie
Colour Tone / Colour Temp. / Digital Clean View /
MPEG Noise Filter / Film Mode / Motion Plus /
Dynamic Backlight
Calibration
Digital Clean View / MPEG Noise Filter /
HDMI Black Level / Film Mode / Dynamic Backlight
――Available input sources may vary depending on the model.
60
Colour Tone
Picture Options
Colour Tone
Standard
Colour Temp.
10000K
If the input source is PC, DVI, HDMI, MagicInfo, HDBT (PC connection).
•• Off / Cool / Standard / Warm
If the input source is AV, Component, DVI, HDMI, HDBT.
Digital Clean View
Off
•• Off / Cool / Standard / Warm1 / Warm2
――Warm1 or Warm2 will be deactivated when the Picture Mode is Dynamic.
MPEG Noise Filter
Off
――Settings can be adjusted and stored for each external device connected to an input on the product.
HDMI Black Level
Normal
Film Mode
Off
Motion Plus
Off
――Available input sources may vary depending on the model.
Colour Temp.
Adjust the colour temperature (Red / Green / Blue). (Range: 3000K–15000K)
――This option is available when Colour Tone is set to Off.
Digital Clean View
-- The displayed image may differ depending on the model.
-- Motion Plus is only available on the EDE, EME models.
If the broadcast signal received by your product is weak, you can activate the Digital Clean View feature to reduce any static
and ghosting that may appear on the screen.
•• Off / Low / Medium / High / Auto
――When the signal is weak, try all the options until the the product displays the best picture.
MPEG Noise Filter
Reduces MPEG noise to provide improved picture quality.
•• Off / Low / Medium / High / Auto
61
HDMI Black Level
Motion Plus
Selects the black level on the screen to adjust the screen depth.
――EDE, EME models are only supported.
•• Normal / Low
――This function is only available when the input signal, connected to the product via an HDMI or DVI
connector, is set to RGB444.
Removes blur and judder from scenes with larger amounts of rapid movement to provide a clearer
picture.
Film Mode
This mode is suitable to view movies.
Sets the product to automatically sense and process film signals from all sources and adjust the picture
for optimum quality.
•• Off / Auto1 / Auto2
――Available in AV, Component (480i / 1080i), HDMI (1080i).
The menu names may vary depending on the country.
Off : Switches Motion Plus off.
Clear : Sets Motion Plus to Clear (suitable for viewing moving images clearly) mode.
Standard : Sets Motion Plus to Standard mode.
Smooth : Sets Motion Plus to Smooth (suitable for viewing moving images naturally) mode.
Custom : Use to reduce the afterimage and judder as much as you want.
•• Blur Reduction : Use to reduce the afterimage as much as you want.
-- This is only supported if the Motion Plus is set to Custom.
•• Judder Reduction : Use to reduce the judder as much as you want.
-- This is only supported if the Motion Plus is set to Custom.
•• LED Clear Motion : Make moving images look more clear.
-- This is only supported if the Motion Plus is set to Custom.
•• Reset: Restore Motion Plus settings to default values.
-- The colour on screen may vary with this option unintentionally.
-- Disabled when PIP is set to On.
――This function may differ depending on the model.
Dynamic Backlight
Automatically adjust the backlight to provide the best possible screen contrast under the current
conditions.
•• Off / On
――The Dynamic Backlight is not available when the input source is set to PC while Video Wall is On.
62
Picture Off
The product screen is turned off but the audio will continue. Press any key on your remote to turn the screen back on.
MENU m → Picture → Picture Off → ENTER E
Picture
Picture Off
Reset Picture
-- The displayed image may differ depending on the model.
Reset Picture
Resets your current picture mode to its default settings.
MENU m → Picture → Reset Picture → ENTER E
Picture
Picture Off
Reset Picture
-- The displayed image may differ depending on the model.
63
Chapter 06
Sound Adjustment
Configure the sound (Sound) settings for the product.
Sound Mode
You can select a sound mode to suit your personal preferences.
•• Standard: Selects the normal sound mode.
MENU m → Sound → Sound Mode → ENTER E
•• Movie: Provides the best sound for movies.
•• Clear Voice: Emphasizes voices over other sounds.
Sound
Sound Mode
•• Music: Emphasizes music over voices.
Standard
•• Amplify: Increase the intensity of high-frequency sound to allow a better listening experience for the hearing impaired.
――If Speaker Select is set to External, Sound Mode is disabled.
Sound Effect
Speaker Settings
Reset Sound
-- The displayed image may differ depending on the model.
64
Sound Effect
Configure your preferred sound effect for output sound.
――If Speaker Select is set to External, Sound Effect is disabled.
MENU m → Sound → Sound Effect → ENTER E
Sound
Sound Mode
Standard
Sound Effect
Speaker Settings
Reset Sound
――Available only when Sound Mode is set to Standard.
•• DTS TruSurround HD (Off / On)
This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head
Related Transfer Function) technology.
•• DTS TruDialog (Off / On)
This function allows you to increase the intensity of a voice over background music or sound effects so that dialog can be
heard more clearly.
•• Equaliser
Use Equaliser to customize sound setting for each speaker.
-- Balance L/R: Adjusts the balance between the right and left speaker.
-- 100Hz / 300Hz / 1kHz / 3kHz / 10kHz (Bandwidth Adjustment): Adjusts the level of specific bandwidth frequencies.
-- Reset: Resets the equalizer to its default settings.
-- The displayed image may differ depending on the model.
65
Speaker Settings
MENU m → Sound → Speaker Settings → ENTER E
Sound
Sound Mode
•• Speaker Select (External / Internal / Receiver)
If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo
caused by the difference in decoding speed between the products speakers and the speakers attached to your audio
receiver. If this occurs, set the product to External.
――When you set Speaker Select to External, the products speakers are turned off.
You will hear sound through the external speakers only. When the Speaker Select is set to Internal, both the product
speakers and the external speakers are on. You will hear sound through both.
Standard
――If there is no video signal, both the products speakers and the external speakers will be mute.
•• Auto Volume (Off / Normal / Night)
The volume can vary depending on the channel.
Sound Effect
Speaker Settings
Automatically equalize the volume level when switching to another channel.
Reset Sound
Night equalizes and decrease the volume level on each channel, so each channel is quieter. Night is useful at night,
when you may want to keep the volume low.
Normal equalizes the volume level on each channel, so that when you change channels, the volume level is the same.
――To use the volume control of a connected source device, set Auto Volume to Off. A change to the volume control of
-- The displayed image may differ depending on the model.
Reset Sound
the connected source device may not be applied if Auto Volume is set to Normal or Night.
――If Speaker Settings is set to External, Auto Volume is disabled.
Reset all sound settings to the factory defaults.
MENU m → Sound → Reset Sound → ENTER E
Sound
Sound Mode
Standard
Sound Effect
Speaker Settings
Reset Sound
-- The displayed image may differ depending on the model.
66
Chapter 07
Network
Network is only available on the DCE, DCE-M, DCE-H models.
Network Status
Network Settings
MENU m → Network → Network Status → ENTER E
MENU m → Network → Network Settings → ENTER E
You can check the current network and Internet status.
Configure network settings to use various smart hub features such as Internet search, content sharing
through a home network and feature updates.
Network type
•• Wireless / Wired
67
Network Settings (Wired)
•• Depending on how your network is configured, you may be able to attach your product to your
LAN by connecting the LAN port on the back of your product directly to a network wall outlet using
a LAN cable.
See the diagram below. Note that the wall outlet is attached to a modem or router elsewhere in
your house.
Connecting to a Wired Network
There are three ways to attach your product to your LAN using cable.
•• You can attach your product to your LAN by connecting the LAN port on the back of your product
to an external modem using a LAN cable.
See the diagram below.
LAN
The LAN Port on the Wall
RJ45
LAN
External Modem
(ADSL / VDSL)
The Modem Port on the Wall
Modem Cable
RJ45
If you have a Dynamic Network, you should use an ADSL modem or router that supports the Dynamic
Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP
address, subnet mask, gateway, and DNS values your product needs to access the Internet so you do not
have to enter them manually. Most home networks are Dynamic Networks.
LAN Cable
•• You can attach your product to your LAN by connecting the LAN port on the back of your product
to an IP Sharer which is connected to an external modem. Use LAN cable for the connection. See
the diagram below.
LAN
The Modem Port on the Wall
External Modem
(ADSL / VDSL)
Modem Cable
IP Sharer
(having DHCP server)
LAN Cable
LAN Cable
RJ45
Some networks require a Static IP address. If your network requires a Static IP address, you must enter the
IP address, subnet mask, gateway, and DNS values manually on your product Cable Setup Screen when
you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values, contact
your Internet Service Provider (ISP).
If you have a Windows computer, you can also get these values through your computer.
――You can use ADSL modems that support DHCP if your network requires a Static IP address.
――ADSL modems that support DHCP also let you use Static IP addresses.
LAN Cable
68
Set the network connection to use Internet services such as perform software upgrades.
2
In the pop-up menu that appears, click Status.
Automatic Network Settings (Wired)
3
On the dialog that appears, click the Support tab.
4
On the Support Tab, click the Details button. The Network connection values are displayed.
Connect to the network using a LAN cable.
Make sure a LAN cable is connected first.
How to set up automatically
How to set up manually
1
Set Network type to Wired from the Network Settings page.
1
Set Network type to Wired from the Network Settings page.
2
Press the Connect button to start Network Settings.
2
Press the Connect button to start Network Settings.
-- The Connect button is only enabled when the LAN cable is properly connected.
3
The network test screen appears and verifies the network connection.
When the connection has been verified, the “Wired network and Internet connection
completed.” message appears.
――If the connection process fails, check the LAN port connection.
――If the automatic process cannot find the network connection values or if you want to set the
connection manually, go to the next section, network setup.
-- The Connect button is only enabled when the LAN cable is properly connected.
3
The network test screen appears and the verification process starts. Press Stop. The verification
process stops.
4
Select IP Settings on network connection screen. The IP Settings screen appears.
5
Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
Manual Network Settings (Wired)
Offices may use static IP addresses.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server
address. Enter these values manually.
Getting the Network Connection Values
To view the Network connection values on most Windows computers, follow these steps.
1
――Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
6
When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
7
When the connection has been verified, the “Wired network and Internet connection
completed.” message appears.
Right click the Network icon on the bottom right of the screen.
69
Network Setting (Wireless)
Automatic Network Setup (Wireless)
Most wireless networks have an optional security system that requires devices that access the network
to transmit an encrypted security code called an Access or Security Key. The Security Key is based on
a Pass Phrase, typically a word or a series of letters and numbers of a specified length you were asked to
enter when you set up security for your wireless network. If you use this method of setting up the network
connection, and have a Security Key for your wireless network, you will have to enter the Pass Phrase
during the the automatic or manual setup process.
Connecting to a Wireless Network
Wireless IP sharer
(router having DHCP server)
USB
The LAN Port on the Wall
LAN Cable
How to set up automatically
Samsung Wireless LAN Adapter
(sold separately)
Samsung recommends using IEEE 802.11n. When you play video over a network connection, the video
may not play smoothly.
――Select a channel for the wireless IP sharer that is not currently being used. If the channel set for the
wireless IP sharer is currently being used by another device nearby, this will result in interference and
communication failure.
1
Set Network type to Wireless from the Network Settings page.
2
The Network function searches for available wireless networks. When done, it displays a list of the
available networks.
3
twice.
――Your product supports only the following wireless network security protocols.
If you select the Pure High-throughput (Greenfield) 802.11n mode and the Encryption type is set to
WEP, TKIP or TKIP AES (WPS2Mixed) on your AP or wireless router, Samsung products will not support a
connection in compliance with new Wi-Fi certification specifications.
――If your wireless router supports WPS (Wi-Fi Protected Setup), you can connect to the network via PBC
――If the desired wireless router does not appear, select Refresh to search again.
――If the router cannot be found after retrying, select the Stop button.
The Add Network button appears.
4
(Push Button Configuration) or PIN (Personal Identification Number). WPS will automatically configure
the SSID and WPA key in either mode.
――Connection Methods: You can setup the wireless network connection in three ways.
Auto Setup (Using the Auto Network Search function), Manual Setup, WPS(PBC)
In the list of networks, press the ▲ or ▼ button to select a network, and then press the E button
If the Enter password. screen appears, go to step 5. If you select a wireless router that does not
have security, go to step 7.
5
If the router has security, enter the Enter password. (Security key or PIN).
70
6
When done, use the right arrow button to move the cursor to Done, and then press E. The
How to set up manually
network connection screen appears and the verification process starts.
1
Set Network type to Wireless from the Network Settings page.
2
The Network function searches for available wireless networks. When done, it displays a list of the
――A connection with the router is established, but the Internet cannot be accessed.
7
When the connection has been verified, the “Your wireless network and Internet connection are
available networks.
setup and ready to use.” message appears.
3
Manual Network Setup (Wireless)
In the list of networks, press the u or d button to select a network, and then press the E button
twice.
Offices may use static IP addresses.
――If the desired wireless router does not appear, select Refresh to search again.
If this is the case, ask the network administrator for the IP address, subnet mask, gateway and DNS server
address. Enter these values manually.
――If the router cannot be found after retrying, select the Stop button.
Getting the Network Connection Values
The Add Network button appears.
4
If the Enter password. screen appears, go to step 5. If you select a wireless router that does not
have security, go to step 7.
To view the Network connection values on most Windows computers, follow these steps.
1
Right click the Network icon on the bottom right of the screen.
5
If the router has security, enter the Enter password. (Security key or PIN).
2
In the pop-up menu that appears, click Status.
6
When done, use the right arrow button to move the cursor to Done, and then press E. The
3
On the dialog that appears, click the Support tab.
4
On the Support Tab, click the Details button. The Network connection values are displayed.
network connection screen appears and the verification process starts.
7
Select Stop while network connections are being attempted. This will stop the connection.
8
Select IP Settings on network connection screen. The IP Settings screen appears.
9
Select the field at the top, press E, and then set IP Settings to Enter manually. Repeat the entry
process for each field in the IP Address.
――Setting IP Settings to Enter manually automatically changes DNS Setting to Enter manually.
71
10When done, select OK at the bottom of the page, and then press E. The network test screen
appears and the verification process starts.
11When the connection has been verified, the “Your wireless network and Internet connection are
setup and ready to use.” message appears.
WPS(PBC)
How to set up using WPS(PBC)
If your router has a WPS(PBC) button, follow these steps.
1
Set Network type to Wireless from the Network Settings page.
2
Select WPS(PBC), press E, and then press E again.
3
Press the WPS(PBC) button on your router within 2 minutes. Your product automatically acquires all
the network setting values it needs and connects to your network.
4
The network connection screen appears, and network setup is done.
72
Wi-Fi Direct
AllShare Settings
MENU m → Network → Wi-Fi Direct → ENTER E
――To use this function, your mobile device should be supported by the Wi-Fi Direct.
MENU m → Network → AllShare Settings → ENTER E
Set to connect the product to wireless mobile devices. Using this function, you can connect wireless
mobile devices with your product directly without a router.
To connect your mobile device with your product using Wi-Fi
Direct, follow these steps:
Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play
function with this product.
•• Allow / Deny: Allows/Blocks the devices.
•• Delete from the list: Deletes the devices from the list.
――This function only deletes the name of the device from the list. If the deleted device is turned on
or tries to connect to the product, it may appear on the list again.
1
Go to Wi-Fi Direct screen. The product starts to search devices.
Using the AllShare Play Function
2
Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.
An alarm window appears informing you that media contents (videos, photos, music) sent from a mobile
phone will be displayed on your product. The contents are played automatically 3 seconds after the
alarm window appears. If you press the RETURN or EXIT button when the alarm window appears, the
media contents are not played.
――The first time a device accesses your product through the media function, a warning popup window
•• PBC (Push Button Configuration): Press the WPS(PBC) button on your Wi-Fi device within 2
minutes. Your product automatically acquires all the network setting values it needs and connects
to your network.
•• PIN: Input the displayed PIN on your device.
――If you want to disconnect the device, select the connected Wi-Fi device, and then select
Disconnected.
appears. Press the E button to select Allow. This permits the phone to access the product freely
and use the AllShare Play function to play content.
――To turn off media contents transmissions from a mobile phone, set Deny in the AllShare Settings.
――Contents may not play on your product depending on their resolution and format.
――The E and ◄ / ► buttons may not work depending on the type of media content.
――Using the mobile device, you can control the AllShare Play. For details, refer to each mobile’s user’s
guide.
73
Server Network Settings
Device Name
MENU m → Network → Server Network Settings → ENTER E
MENU m → Network → Device Name → ENTER E
Connect to server
To run Player connect to a network.
Select or enter a device name.
This name can be shown on network remote controls over the network.
•• User Input / [Signage]Display 1 ~ 6
•• Server Address / SSL / Port
――If the SSL option is enabled, the server is configured to use https and data transfer is encrypted.
――Enter the server IP address and port number. Use 7001 as the port number. (If unable to connect to
the server using port number 7001, check with your server administrator to find the correct port
number and then change the port number.)
Server Access
Select a method to connect the server network.
•• Allow / Deny
FTP Mode
Specify the FTP operating mode.
•• Active / Passive
74
Chapter 08
Applications
Source List
Refresh
MENU m → Applications → Source List → TOOLS → Refresh → ENTER E
Source allows you to select a variety of sources and change source device names.
If you cannot find a device you want, select Refresh to refresh the list.
You can display the screen of a source device connected to the product. Select a
source from Source List to display the screen of the selected source.
――The input source can also be changed by using the SOURCE button on the
Edit Name
remote control.
――The screen may not display correctly if an incorrect source is selected for the
source device you want to convert to.
MENU m → Applications → Source List → ENTER E
Applications
Source List
MagicInfo Lite
MENU m → Applications → Source List → TOOLS → Edit Name → ENTER E
Sometimes the screen will not display properly unless the name of a source device is specified in Edit Name.
In addition, it is best to rename the source device in Edit Name to obtain optimal picture quality.
――The list can include the following source devices. Source devices on the list differ depending on the selected source.
VCR / DVD / Cable STB / Satellite STB / PVR STB / AV Receiver / Game / Camcorder / PC / DVI PC / DVI Devices / TV /
IPTV / Blu-ray / HD DVD / DMA
――Available settings in the Picture menu depend on the current source and settings made in Edit Name.
Information
MENU m → Applications → Source List → TOOLS → Information → ENTER E
You can see detailed information about the selected external device.
-- The displayed image may differ depending on the model.
75
MagicInfo Lite
MENU m → Applications → MagicInfo Lite → ENTER E
Applications
MagicInfo is a business solution that allows the product to be used as a signage (advertising media). Using the solution, play
image and video files from the internal memory or a connected USB storage device.
――DCE, DCE-M, DCE-H models are only supported.
Playing content from the internal memory or USB
Play content from the internal memory or a connected USB storage device.
Source List
MagicInfo Lite
-- The displayed image may differ depending on the model.
76
Device : All
Content : All
Sort by : File Name
Options
Available features in the MagicInfo page
The MagicInfo list page provides the following features.
•• Device
-- Select either Internal or USB to search for a desired device list.
All / Internal / USB
•• Content
-- Select a content type as criterion to search for a desired content list.
All / Video / Image
•• Sort by
Specify the content sort criterion.
-- The displayed image may differ depending on the model.
Network Channel
Play content, templates and schedules configured on the server.
•• You can view whether the server is connected (approval) in the Player menu
screen.
To view whether the server is connected when a Network Channel is
running, press INFO on the remote.
1
Select Network Channel from the Player menu.
――The No channels message appears if no channel has been registered in
Network Channel.
2
Network Channel will run.
-- File Name / Recently played
•• Options
Options menu items in the MagicInfo screen
Option Name
Operations
Play Selected
Select and play desired content.
Send
Copy content to another storage device.
Delete
Delete desired content.
Settings
Configure detailed properties of content.
――See the following page for details on the Settings feature.
77
Settings
Default Storage
Select the storage location that you want to download scheduled channels from the network to.
Settings
•• Internal / USB
Select the storage location that you want to download scheduled channels from
the network to.
Default Storage
Repeat Mode
Repeat Mode
Set repeat mode whether to repeat playing contents or not.
Internal
One
Close
•• One / All
Picture Size
Display Duration
Safely Remove USB Device
Reset Settings
Picture Size
Set Picture Size to either Fit to Screen or Original Size.
•• Fit to Screen / Original Size
――Available only for Video and Image content.
-- The displayed image may differ depending on the model.
Display Duration
Set the duration for each page in a slideshow.
――Available only for Template and Image content.
Safely Remove USB Device
Safely removes USB memory
Reset Settings
Restore all the values under Settings to the default when the product was purchased.
78
Chapter 09
System
Setup
Go through the initial setup steps like you did the first time you used this product.
――Enter your 4 digit PIN number. The default PIN number is “0-0-0-0".
If you want to change the PIN number, use the Change PIN function.
MENU m → System → Setup → ENTER E
Set the HDBaseT standby mode.
――EME models are only supported.
System
•• Off: The device cannot be turned on via HDBT once it is turned off.
•• On: Keep the HDBT module active when the device is turned off. (This uses more power.)
Setup
Menu Language
English
Multi Control
Time
Eco Solution
Auto Protection Time
Off
Screen Burn Protection
-- The displayed image may differ depending on the model.
79
Menu Language
MENU m → System → Menu Language → ENTER E
Set the menu language.
――A change to the language setting will only be applied to the onscreen menu display. It will not be
applied to other functions on your PC.
Multi Control
MENU m → System → Multi Control → ENTER E
Configuring settings for Multi Control
•• ID Setup
Assign an ID to a set. (Range: 0~99)
Press u or d to select a number, and press E.
•• ID Input
Enter the ID number of the product connected to the input cable for input signal reception.
Enter the number you want using the number buttons on the remote control.
•• PC Connection
Select a method to connect to MDC to receive the MDC signal.
――DCE, DCE-M, DCE-H models are only supported.
-- RS232C cable
Communicates with the MDC via a RS232C cable.
-- RJ-45 (LAN)/Wi-Fi Network
Communicate with MDC over Wi-Fi.
80
Time
You can configure Clock Set or Sleep Timer. You can also set the product to automatically turn on or off at a specified time
using the Timer function.
MENU m → System → Time → ENTER E
Clock Set
Select Clock Set. Select Date or Time, and then press E.
Time
Use the number buttons to enter numbers or press the up and down arrow buttons. Use the left and right arrow buttons to
move from one entry field to the next. Press E when done.
――Available only when Clock Mode is set to Manual.
Clock Set
Sleep Timer
On Timer
Off Timer
Holiday Management
-- The displayed image may differ depending on the model.
Off
――You can set the Date and Time directly by pressing the number buttons on the remote control.
Sleep Timer
Automatically shuts off the product after a preset period of time.
(Off / 30 min / 60 min / 90 min / 120 min / 150 min / 180 min)
――Use the up and down arrows to select a period of time, and then press E. To cancel Sleep Timer, select Off.
On Timer
Set On Timer so that your product turns on automatically at a time and on a day of your choosing.
The power is turned on with the specified volume or input source.
On Timer: Set the on timer by making a selection from one of the seven options. Ensure you set the current time first.
(On Timer 1 ~ On Timer 7)
――You must set the clock before you can use On Timer.
•• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the
days you want On Timer to turn on your product.
――The check mark indicates days you’ve selected.
•• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left
and right arrow buttons to change entry fields.
•• Volume: Set the desired volume level. Use the left and right arrow buttons to change the volume level.
•• Source: Select the input source of your choice.
81
Off Timer
Time
Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer 1 ~ Off Timer 7)
――You must set the clock before you can use Off Timer.
Clock Set
Sleep Timer
On Timer
Off Timer
Holiday Management
Off
•• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the
days you want Off Timer to turn off your product.
――The check mark indicates days you’ve selected.
•• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left
and right arrow buttons to change entry fields.
Holiday Management
Timer will be disabled during a period specified as a holiday.
-- The displayed image may differ depending on the model.
•• Add: Specify the period you want to add as a holiday.
Select the start and end dates of the holiday you want to add using the u/d buttons, and click the Save button.
The period will be added to the list of holidays.
-- Start: Set the start date of the holiday.
-- End: Set the end date of the holiday.
-- Delete: Delete all items from the list of holidays.
Select Delete. The message "Delete all holidays?" will appear.
Select Yes. All holidays will be deleted.
•• Apply: Set the On Timer and Off Timer to not activate on public holidays.
-- Press E to select the On Timer and Off Timer settings you do not want to activate.
-- The selected On Timer and Off Timer will not activate.
82
Eco Solution
Energy Saving
Reduce the power consumption by adjusting the screen brightness.
MENU m → System → Eco Solution → ENTER E
•• Off / Low / Medium / High
Eco Sensor
Eco Solution
Energy Saving
Off
Eco Sensor
Off
No Signal Power Off
15 min
Auto Power Off
-- The displayed image may differ depending on the model.
Off
To enhance your power savings, the picture settings will automatically adapt to the light in the room.
•• Off / On
――Adjusting the Backlight setting under Picture while Eco Sensor is on will disable the Off.
――If the screen contrast is not sufficient, set the Eco Sensor to Off.
If the Eco Sensor is Off, it may not comply with energy standards.
Min. Backlight
When Eco Sensor is On, you can manually adjust the minimum screen brightness. Min. Backlight is the darkest backlight
mode. Make sure the Min. Backlight setting is lower than the Backlight setting.
――If Eco Sensor is On, the display brightness may change (become slightly darker or brighter) depending on the surrounding
light intensity.
No Signal Power Off
Save power by turning the device off when no signal is received from any source.
•• Off / 15 min / 30 min / 60 min
――Disabled when an attached PC is in power saving mode.
――The product will automatically power off at a specified time. The time can be changed as required.
Auto Power Off
The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel
within 4 hours to prevent overheating.
•• Off / On
83
Auto Protection Time
If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the
formation of burnt in ghost images on the screen.
•• Off / 2 hours / 4 hours / 8 hours / 10 hours
MENU m → System → Auto Protection Time → ENTER E
System
Auto Protection Time
Off
-- The displayed image may differ depending on the model.
84
Screen Burn Protection
MENU m → System → Screen Burn Protection → ENTER E
To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology.
Pixel Shift moves the picture slightly on the screen.
The Pixel Shift Time setting allows you to programme the time between movements of the picture in minutes.
Pixel Shift
Screen Burn Protection
Minimize image retention by finely moving pixels horizontally or vertically.
Pixel Shift
Off
Timer
Off
Immediate display
Off
Side Grey
Off
•• Pixel Shift (Off / On)
――Horizontal, Vertical and Time are enabled only when Pixel Shift is set to On.
•• Horizontal: Sets how many pixels the screen moves horizontally.
•• Vertical: Sets how many pixels the screen moves vertically.
•• Time: Set the time interval for performing the horizontal or vertical movement, respectively.
Available Pixel Shift Settings and Optimum Settings.
Available Settings
-- The displayed image may differ depending on the model.
Optimum Settings
Horizontal (pixels)
0~4
4
Vertical (pixels)
0~4
4
Time (minute)
1 min ~ 4 min
4 min
――The Pixel Shift value may differ depending on the product size (inches) and mode.
――Displaying a still image or a 4:3 output for an extended period of time may cause image retention. This is not a defect in the
product.
――If Picture Size is set to Screen Fit, Pixel Shift is disabled.
85
Timer
Screen Burn Protection
You can set the timer for Screen Burn Protection.
Pixel Shift
Off
Timer
Off
Immediate display
Off
•• Off
Side Grey
Off
•• Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period).
――Period and Time can be configured when Repeat is selected.
-- The displayed image may differ depending on the model.
The Screen Burn Protection feature stops automatically after a specified period of time.
Timer
•• Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to
End Time).
――The option is enabled only when Clock Set is configured.
•• Mode: Select a screen protective pattern to display.
-- Pixel: Pixels on the screen alternate black continuously.
-- Rolling bar: A vertical bar moves left to right.
-- Fading screen: The entire screen becomes brighter, then darker.
――The Rolling bar and Fading screen patterns appear only once regardless of the specified repeat period or time.
•• Period: Specify the time interval to activate the Screen Burn Protection function.
-- 1 hour ~ 10 hour
――The option is enabled when Repeat is selected for Timer.
•• Time: Specify the duration to keep the Screen Burn Protection function on.
-- 10 Sec ~ 50 Sec
――Enabled when Timer is set to Repeat and Mode is set to Pixel.
•• Start Time: Set the start time to activate the screen protection function.
――The option is enabled when Interval is selected for Timer.
•• End Time: Set the end time to deactivate the screen protection function.
――The option is enabled when Interval is selected for Timer.
86
Immediate display
Screen Burn Protection
Pixel Shift
Off
Timer
Off
Immediate display
Off
Side Grey
Off
Select the screen saver you want to display immediately.
•• Off / Pixel / Rolling bar / Fading screen
Side Grey
When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen.
•• Off / Light / Dark
-- The displayed image may differ depending on the model.
87
Ticker
Input text while a video or image is displayed and display the text on the screen.
•• Off / On
――Message, Time, Position, Motion, and Font Style are enabled only when Ticker is set to On.
MENU m → System → Ticker → ENTER E
•• Message: Enter a message to display on the screen.
•• Time: Set the Start Time and End Time to display a Message.
System
Ticker
Off
-- The displayed image may differ depending on the model.
-- The Ticker function is only available when Menu Language is set to English.
•• Position: Select an orientation to display a Message from Horizontal and Vertical.
-- Horizontal (Left / Centre / Right)
-- Vertical (Top / Middle / Bottom)
•• Motion: Specify the Direction and Speed to display a Message.
-- Motion (Off / On)
-- Direction (To the Left / To the Right / To the Top / To the Bottom)
-- Speed (Slow / Normal / Fast)
――Direction and Speed are enabled only when Motion is set to On.
•• Font Style: Specify the message Size and Font colour.
88
Video Wall
Customize the layout of multiple displays that are connected to form a video wall.
In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays.
To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support the MagicInfo
function.
MENU m → System → Video Wall → ENTER E
Video Wall
Video Wall
Video Wall
On
· Format
Full
· Horizontal
1
· Vertical
1
· Screen Position
-- The displayed image may differ depending on the model.
-- Some models may not support the MagicInfo function.
You can activate or deactivate Video Wall.
To organize a video wall, select On.
Format
Select a format to display images on multiple displays.
•• Full: Display images in full screen.
•• Natural: Display images at the original resolution without enlarging or reducing.
――The Format option is only enabled when Video Wall is set to On.
Horizontal
This function automatically divides the screen according to the specified number of horizontal displays.
-- The Video Wall option is only enabled when PIP is set to Off.
Enter the number of horizontally arranged displays.
-- If more than four displays are connected horizontally and vertically, it is recommended that
you use an input resolution of XGA (1024 x 768) level or higher to prevent a dark picture due
to degradation in the contrast or colour intensity.
The horizontal screen will automatically be divided according to the number entered.
A maximum of 15 displays can be assigned to the horizontal arrangement.
――The screen can be divided into a maximum of 100 screens (horizontal and vertical screens multiplied). For example, if the
horizontal arrangement is set to 15, a maximum of 6 displays can be assigned to the vertical arrangement. Conversely, if the
vertical arrangement is set to 15, a maximum of 6 displays can be assigned to the horizontal arrangement.
――The Horizontal option is only enabled when Video Wall is set to On.
89
Vertical
Video Wall
Video Wall
On
· Format
Full
· Horizontal
1
· Vertical
1
· Screen Position
This function automatically divides the screen according to the specified number of vertical displays.
Enter the number of vertically arranged displays.
The vertical screen will automatically be divided according to the number entered.
A maximum of 15 displays can be assigned to the vertical arrangement.
――The screen can be divided into a maximum of 100 screens (horizontal and vertical screens multiplied). For example, if the
horizontal arrangement is set to 15, a maximum of 6 displays can be assigned to the vertical arrangement. Conversely, if the
vertical arrangement is set to 15, a maximum of 6 displays can be assigned to the horizontal arrangement.
――The Vertical option is only enabled when Video Wall is set to On.
Screen Position
-- The displayed image may differ depending on the model.
You can customize the arrangement of split screens by moving displays identified with a number using the Screen Position
function.
Select Screen Position to display the arrangement of displays (identified with a number) specified according to the
Horizontal or Vertical settings. To customize the arrangement, move a number (display) using the direction buttons on the
remote control and press E.
――A maximum of 100 displays can be arranged in Screen Position.
――The Screen Position option is only enabled when Video Wall is set to On.
――The Screen Position window is only displayed when Horizontal and Vertical are configured.
90
Source AutoSwitch Settings
Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will
automatically search the different video input sources for active video.
MENU m → System → Source AutoSwitch Settings → ENTER E
Source AutoSwitch
When the Source AutoSwitch is On, the display video source will automatically be searched for active video.
Source AutoSwitch Settings
The Primary Source selection will be activated, if the current video source is not recognized.
Source AutoSwitch
On
· Primary Source Recovery
Off
· Primary Source
All
· Secondary Source
PC
Secondary Source selection will become active, if no primary video source is available.
If both the primary and secondary input sources are not recognized, the display will perform two searches for an active source,
each search checking the primary and then secondary source. If both searches fail, the display will return to the first video
source and display a message indicating that there is no signal.
When the Primary Source selection is set to All, the display will search all the video source inputs twice in sequence looking
for an active video source, returning back to the first video source in the sequence if no video is found.
Primary Source Recovery
-- The displayed image may differ depending on the model.
Select whether to restore the selected primary input source when a primary input source is connected.
――The Primary Source Recovery function is disabled if Primary Source is set to All.
Primary Source
Specify Primary Source for the automatic input source.
Secondary Source
Specify Secondary Source for the automatic input source.
91
Change PIN
MENU m → System → Change PIN → ENTER E
The Change PIN screen will appear.
Choose any 4 digits for your PIN and enter it in Enter New PIN. Reenter the same 4 digits in Confirm New PIN.
When the Confirm screen disappears, press the Close button. The product has memorised your new PIN.
System
Change PIN
-- The displayed image may differ depending on the model.
92
General
Max. Power Saving
Turns off the product to reduce power consumption after the PC has been left idle for a specified period of time.
MENU m → System → General → ENTER E
•• Off / On
――Available only PC, DVI, HDMI mode.
General
Max. Power Saving
On
Game Mode
Off
Auto Power On
Off
Safety Lock
Off
Button Lock
Off
Standby Control
Off
Network Standby
Off
Game Mode
When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by
selecting game mode.
•• Off / On
――Precautions and limitations for Game Mode
To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.
――Game Mode is not available when the input source is set to PC.
――If Game Mode is On. Picture Mode is set to Standard and Sound Mode is set to Movie.
Auto Power On
This feature automatically turns on the product as soon as it is plugged in. Pressing the power button is not needed.
•• Off / On
-- The displayed image may differ depending on the model.
Safety Lock
It sets safe lock function.
•• Off / On
All the menus and buttons of the product and remote control, except for the LOCK button on the remote control, will be
locked by the Safety Lock function.
To unlock the menus and buttons, press the LOCK button and then enter the password (default password: 0 - 0 - 0 - 0).
93
Button Lock
General
This menu can be used to lock the buttons on the product.
Max. Power Saving
On
Game Mode
Off
Auto Power On
Off
Standby Control
Safety Lock
Off
You can set the screen standby mode to be applied when an input signal is received.
Button Lock
Off
Standby Control
Off
HDBT Standby
Off
Network Standby
Off
Only the remote control can control the product if Button Lock is set to On.
•• Off / On
•• Auto
Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
The message No Signal will appear if no source device is connected.
•• On
Power-saving mode will activate if no input signals are detected.
•• Off
The message No Signal will appear if no input signals are detected.
――The Standby Control option is only enabled when Source List is set to PC, DVI, HDMI.
-- The displayed image may differ depending on the model.
――If No Signal is displayed although a source device is connected, check the cable connection.
HDBT Standby
Keep the HDBT module active when the device is turned off. (This uses more power.)
•• Off / On
――EME models are only supported.
Network Standby
This feature keeps the network power on when the product turns off.
•• Off / On
――This function is only available for models that can connect to a network.
94
Lamp Schedule
General
Off
Lamp Schedule
OSD Display
Power On Adjustment
0 Sec
Temperature Control
-- The displayed image may differ depending on the model.
77
Adjusts the luminance to a user-specified value at a specified time.
•• Off / On
OSD Display
Displays or hides a menu item on the screen.
•• Source OSD / No Signal OSD / MDC OSD
Power On Adjustment
You can set the warm-up time for the screen to turn on after the power button is pressed. (Range: 0 – 50 seconds)
――A warm-up time that is too short may damage the product due to overvoltage.
Temperature Control
This function detects the internal temperature of the product. You can specify the temperature range that is acceptable.
The default temperature is set to 77 C.
The recommended operating temperature for this product is 75 to 80 C (based on an ambient temperature of 40 C).
――The screen will become darker if the current temperature exceeds the specified temperature limit. If the temperature
continues to rise, the product will power off to prevent overheating.
95
Anynet+ (HDMI-CEC)
Anynet+ (HDMI-CEC)
MENU m → System → Anynet+ (HDMI-CEC) → ENTER E
Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung
product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your
Samsung device has this feature, check if there is an Anynet+ logo on it.
――You can only control Anynet+ devices using the product remote control, not the buttons on the product.
Anynet+ (HDMI-CEC)
――The product remote control may not work under certain conditions. If this occurs, reselect the Anynet+ device.
Anynet+ (HDMI-CEC)
On
Auto Turn Off
Yes
-- The displayed image may differ depending on the model.
-- The Anynet+ functions do not operate with other manufacturers’ products.
-- For instructions explaining how to connect Anynet+ external devices, refer to the device’s user
manual.
-- You can connect only one receiver (home theatre).
――Anynet+ works when the AV device supporting Anynet+ is in the standby or on status.
――While in PIP mode, Anynet+ functions only when an AV device is connected as the primary display. It does not work if the
AV device is connected as a secondary display.
――Anynet+ supports up to 12 AV devices in total. Note that you can connect up to 3 devices of the same type.
Anynet+ Menu
The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the product.
Anynet+ Menu
Description
View PC
Changes Anynet+ mode to PC mode.
Device List
Shows the Anynet+ device list.
(device_name) MENU
Shows the menu of the connected device menus. E.g. if a DVD player is connected,
the disc menu of the DVD player will appear.
(device_name) Tools
Shows the tools menu of the connected device. E.g. if a DVD player is connected, the
tools menu of the DVD player will appear.
――Depending on the device, this menu may not be available.
(device_name) Title Menu
Shows the title menu of the disc in the connected device. E.g. If a DVD player is
connected, the title menu of the movie in the DVD player will appear.
――Depending on the device, this menu may not be available.
96
Auto Turn Off
Anynet+ (HDMI-CEC)
Anynet+ (HDMI-CEC)
On
Auto Turn Off
Yes
Setting an Anynet+ Device to turn Off automatically when the product is turned off.
•• No / Yes
――If Auto Turn Off is set to Yes, running external devices will turn off at the same time as the product powers off.
――May not be enabled depending on the device.
Switching between Anynet+ Devices
-- The displayed image may differ depending on the model.
1
Press the TOOLS button, select Anynet+ (HDMI-CEC), and then press E.
2
Select Device List, and then press the E button.
If you cannot find a device you want, select Refresh to refresh the list.
3
Select a device, and then press the E button. You can switch to the selected device.
――The Device List menu appears only when you set Anynet+ (HDMI-CEC) to On in the System menu.
――Switching to the selected device may take up to 2 minutes. You cannot cancel the switching operation while switching is in
progress.
――If you have selected an Anynet+ device by pressing the SOURCE button and then selecting its input source, you cannot use
the Anynet+ function.
――Make sure to switch to an Anynet+ device by using the Device List.
97
Troubleshooting for Anynet+
Problem
Anynet+ does not work.
Possible Solution
•• Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices only.
•• You can connect only one receiver (home theatre).
•• Check if the Anynet+ device power cord is properly connected.
•• Check the Anynet+ device’s Video/Audio/HDMI cable connections.
•• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+setup menu.
•• Check whether the remote control is Anynet+ compatible.
•• Anynet+ doesn’t work in certain situations. (initial setup)
•• If you have removed and then reconnected the HDMI cable, please make sure to search devices again or turn your product
off and on again.
•• Check if the Anynet+ function of the Anynet device is set on.
I want to start Anynet+.
•• Check if the Anynet+ device is properly connected to the product and check if the Anynet+ (HDMI-CEC) is set to On in the
Anynet+ System menu.
•• Press the TOOLS button to display the Anynet+ menu and select a menu you want.
I want to exit Anynet+.
•• Select View PC in the Anynet+ menu.
•• Press the SOURCE button on the product remote control and select a non- Anynet+ device.
The message “Disconnecting
Anynet+ device ...” appears on the
screen.
•• You cannot use the remote control when you are configuring Anynet+ or switching to a view mode.
The Anynet+ device does not
play.
•• You cannot use the play function when initial setup is in progress.
•• Use the remote control after the product has completed Anynet+ configuration or has finished switching to Anynet+.
98
Problem
The connected device is not
displayed.
Possible Solution
•• Check whether or not the device supports Anynet+ functions.
•• Check whether or not the HDMI cable is properly connected.
•• Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ System menu.
•• Search Anynet+ devices again.
•• Anynet+ requires an HDMI connection. Make sure the device is connected to your product with an HDMI cable.
•• Some HDMI cables may not support Anynet+ functions.
•• If the connection is terminated because there has been a power failure or the HDMI cable has been disconnected, please
repeat the device scan.
99
Clone Product
MENU m → System → Clone Product → ENTER E
Clone Product
Clone to USB
Clone from USB
Export the product settings to a USB device or load the settings via a USB device.
This option is useful when assigning the same settings to several products.
•• Clone to USB: Copy the product settings to a USB device.
•• Clone from USB: Assign the settings saved in a USB device to the product.
-- After configuration is complete, the product is rebooted automatically.
――The option may not work properly if the USB device contains a file other than a settings file.
――Confirm that the USB device functions properly before running the option.
――The option is available for products with the same Model Code and Software Version.
Go to Support → Contact Samsung and find the product Model Code and Software Version.
-- The displayed image may differ depending on the model.
Reset System
This option returns the current settings under system to the default factory settings.
MENU m → System → Reset System → ENTER E
System
Reset System
-- The displayed image may differ depending on the model.
100
Reset All
MENU m → System → Reset All → ENTER E
This option returns all the current settings for a display to the default factory settings.
DivX® Video On Demand
MENU m → System → DivX® Video On Demand → ENTER E
Shows the registration code authorized for the product.
If you connect to the DivXⓇ web site and register using that code, you can download the VOD
registration file.
For more information about DivXⓇ VOD, visit “http://vod.divx.com”.
PC module power
MENU m → System → PC module power → ENTER E
The PC module can be turned on/off separately from the LFD.
Synced power-on
Set to Off to turn on the PC module without turning on the LFD.
•• Off / On
Synced power-off
Set to Off to turn off the PC module without turning off the LFD.
•• Off / On
101
Chapter 10
Support
Software Update
MENU m → Support → Software Update → ENTER E
The Software Update menu lets you upgrade your product software to the latest version.
――Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade.
――When you upgrade software, all video and audio settings you have made will return to their default settings. We advise you to write down your settings so that you can
easily reset them after the upgrade.
Update now
Update the software to the latest version.
Contact Samsung
MENU m → Support → Contact Samsung → ENTER E
View this information when your product does not work properly or when you want to upgrade the software.
You can find information regarding our call centres and how to download products and software.
――Contact Samsung and find the product Model Code and Software Version.
102
Chapter 11
Playing photos, videos and music (Media Play)
Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device.
Play photos, videos or music saved on a storage device.
Play a variety of content using the following methods.
•• Using a USB device: Play media content such as videos, photos and music from a USB device.
•• Connecting a storage device: Play media content saved on a storage device such as a smartphone, camera, PC or cloud service.
Read the following before using media play with a USB device
Caution
•• Before connecting a USB device to the product, back up files to ensure your data is not damaged or lost.
Samsung Electronics is not liable for any damage or loss of data.
•• Do not remove a USB device while it is loading.
•• If a USB device is connected using a USB extension cable, the USB device may not be recognized or files saved on the device may not be able to be read.
•• If the product does not recognize a connected USB device, the files on the USB device may be corrupted or may not be able to be played.
If this occurs, connect the USB device to the PC to format the device, then make sure the device is connected properly.
•• USB HDD greater than 2TB is not supported.
103
Compatible devices with media play
•• Some USB digital cameras, smartphones and audio devices may not be compatible with the product.
•• Media play is only compatible with USB MSC devices.
•• MSC device refers to a Mass Storage Class Bulk-Only Transport device.
Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs. (USB hubs are not supported.)
These MSC devices must be connected directly to a USB port on the product.
•• If more than one Picture Transfer Protocol (PTP) device is connected, only one will work at a time.
•• If multiple MSC devices are connected, some devices may not be recognized. USB devices that require high power (higher than 500mA or 5V) may not be supported.
•• If an overheating warning message appears when a USB device is connected or used, the USB device may not be recognized or function properly.
•• The screensaver activates if the product is left idle for a period of time specified in Auto Protection Time.
•• Power-saving mode on some external hard disk drives may automatically deactivate after connecting to the product.
File system and formats
•• Media play may not function properly with unlicensed multimedia files.
•• Media Transfer Protocol (MTP) is not supported.
•• Supported file systems include FAT16, FAT32 and NTFS (read only).
•• Media play supports the sequential JPEG format.
It does not support the progressive JPEG format.
•• Images with a higher resolution take longer to be displayed on the screen.
•• The maximum JPEG resolution supported is 15360x8640 pixels.
•• If a file is incompatible or corrupted, a message Not Supported File Format. appears.
•• When sorting files in folder view mode, a maximum of 1000 files can be displayed in each folder.
•• If a USB device contains 8000 files and folders or more, some files and folders may not open.
•• DRM MP3 files downloaded from websites that charge a fee cannot be played.
――Digital Rights Management (DRM) refers to a system for protecting the copyrights of data circulated via the Internet or other digital media by enabling secure
distribution and/or disabling illegal distribution of the data.
104
Using a USB device
It is recommended to use a USB HDD that
has a power adapter.
Connecting a USB device
1
Turn on your product.
2
Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product.
3
The New device connected. page automatically appears as soon as a USB device connects to the product.
――If only one USB device is connected, files saved on the USB device are displayed automatically.
――To view content saved on a USB device, connect the USB device to a USB port on the product.
Removing a USB device
It is recommended to remove a USB
device using the Disconnect USB Device
function.
Removing a USB device from Source
1
Press SOURCE on the remote control. Alternatively, go to Source using the OSD menu.
SOURCE → Source
2
Select USB from Source, and then press the TOOLS button on the remote control. Optional menu items are displayed.
3
Select Disconnect USB Device and wait until the USB device is disconnected. The USB device is disconnected.
105
Menu items in the media content list page
Option Name
Operations
Slide Show
Start a slideshow.
――This menu item is not available if Sort by is set to Folder.
Encoding
Select an encoding language if the title of media content appears corrupted.
Play Selected
Select and play desired content from the media content list.
Photos
Videos
Music
c
c
c
c
c
106
Available buttons and features during photo playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
Pressing the INFO button while a file is
selected will display information about the
selected file.
•• Previous / Next
View the previous or next photo.
•• Start Slide Show / Stop Slide Show
Start or stop a slideshow. Using a slideshow, it is possible to play all photos in a folder.
•• Slideshow Settings
-- Speed: Change the slideshow speed.
-- Effects: Apply transition effects between photos.
•• Zoom
Zoom in on photos up to 4x.
•• Rotate
Rotate photos.
•• Background Music
Play background music while viewing photos.
-- Background Music / Mini Player
――Make sure a music file is saved on the same device.
――Pause the current music playing or switch to another music file using Mini Player.
•• Settings
Option Name
Operations
Picture Mode
Change the Picture Mode.
Sound Mode
Change the Sound Mode.
――This menu item is only available when Background Music is playing.
Information
View information about a file.
107
Available buttons and features
during video playback
Pressing the E or TOOLS button displays the following buttons. The RETURN
button makes the buttons disappear.
•• Pause / Play
Pause or play a video.
The following features are available in pause mode. Note that sound cannot
be heard in pause mode.
Option Name
Operations
Picture Mode
Change the Picture Mode.
Sound Mode
Change the Sound Mode.
Audio Language
Play a video using a desired language. This feature only activates when a streaming file that
supports multiple audio formats is playing.
Information
View information about a file.
•• Rewind / Fast Forward
Rewind or fast forward a video. Speed up playback up to 3x, if required. To
change the playback speed to the original speed, select ∂.
•• Previous / Next
To play the previous video, select  twice. Selecting  once will play the
current video from the beginning.
To play the next video, select ‚.
•• Search
Select and play another video in the same folder. (Search Titles)
•• Repeat Mode
Configure Repeat Mode. (Off, Repeat One, Repeat All)
•• Picture Size
Change the screen size (Picture Size). Supported screen sizes vary
depending on the image. (Original / Mode 1 / Mode 2 / Smart View 1 /
Smart View 2)
•• Settings
108
Available buttons and features during music playback
Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear.
•• Pause / Play
Pause or play music.
•• Rewind / Fast Forward
Rewind or fast forward music. Speed up playback up to 3x, if required. To play the previous music file, select ∂ twice.
•• Previous / Next
To play the previous music file, select  twice. Selecting  once will play the current music from the beginning.
To play the next music file, select ‚.
•• Repeat
Configure Repeat mode. One Song plays the current music file repeatedly. All plays all files in a folder repeatedly.
•• Shuffle
Enable or disable shuffle playback mode.
•• Sound Mode
Change the Sound Mode.
109
Supported Subtitle and Media play file formats
Subtitle
External
•• MPEG-4 timed text (.ttxt)
•• SAMI (.smi)
•• SubRip (.srt)
•• SubViewer (.sub)
•• Micro DVD (.sub or .txt)
•• SubStation Alpha (.ssa)
•• Advanced SubStation Alpha (.ass)
•• Powerdivx (.psb)
Internal
•• Xsub
Container: AVI
•• SubStation Alpha
Container: MKV
•• Advanced SubStation Alpha
Container: MKV
•• SubRip
Container: MKV
•• MPEG-4 timed text
Container: MP4
Compatible image file format
Type
JPEG
4096 x 4096
PNG
BMP
110
Supported music file formats
File Extension
*.avi, *.mkv, *.asf, *.wmv, *.mp4, *.3gp, *.vro, *.mpg,
*.mpeg, *.ts, *.tp, *.trp, *.mov, *.flv, *.vob, *.svi, *.divx
Supported Video Formats
•• Video content will not play, or not play correctly, if there is an error in the content or the container.
•• Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec listed in the table above.
•• If the Index Table is in error, the Seek (Jump) function is not supported.
•• You may experience file stuttering while playing a video through a network connection.
•• The menu may take longer to appear if the video’s bit rate exceeds 10Mbps.
•• Some USB/digital camera devices may not be compatible with the player.
Video Decoder
Audio Decoder
Supports up to H.264, Level 4.1
Supports up to WMA 10 Pro 5.1 channel.
H.264 FMO / ASO / RS, VC1 SP / MP / AP L4 and AVCHD are not supported.
WMA lossless audio is not supported.
For all Video codecs except MVC, VP8, VP6:
QCELP, AMR NB/WB are not supported.
•• Below 1280 x 720: 60 frame max
If Vorbis is only in Webm container, supports up to 2 channel.
•• Above 1280 x 720: 30 frame max
GMC 2 over is not supported.
Supports only BD MVC Spec.
111
Container
Video Codec
Resolution
Frame rate
(fps)
Bit rate
(Mbps)
Audio Codec
3gpp
DivX 3.11 /DivX4.X
1280 x 720
60
30
AAC
asf
avi
flv
mkv
mov
AC3
XVID
H.264 BP/MP/HP
MPEG-4 SP/ASP
mp4
ps
vro
DD+
DTS Core
HE-AAC
LPCM
WINDOW MEDIA VIDEO V9
ts
vob
ADPCM
MP3
WMA
MPEG2
MPEG1
H.263
DivX5.x
DivX6.X
112
Container
Video Codec
Resolution
Frame rate
(fps)
Bit rate
(Mbps)
Audio Codec
3gpp
DivX 3.11 /DivX4.X
1920 x 1080
30
30
AAC
asf
avi
flv
mkv
mov
mp4
AC3
XVID
ADPCM
DD+
H.264 BP/MP/HP
DTS Core
MPEG-4 SP/ASP
HE-AAC
LPCM
WINDOW MEDIA VIDEO V9
ps
ts
vob
MP3
MPEG2
WMA
MPEG1
vro
H.263
DivX5.x
DivX6.X
MOTION JPEG
640 x 480
30
8
113
Chapter 12
Troubleshooting Guide
Requirements Before Contacting Samsung Customer Service Centre
Before calling Samsung Customer Service
Centre, test your product as follows. If
the problem persists, contact Samsung
Customer Service Centre.
Testing the Product
Check if your product is operating normally by using the product test function.
If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
If the screen remains blank, check the PC
system, video controller and cable.
1
Power off both the PC and product.
2
Disconnect all the cables from the product.
3
Power on the product.
4
If No Signal is displayed, the product is operating normally.
Checking the Resolution and Frequency
Not Optimum Mode will briefly be displayed if a mode that exceeds a supported resolution is selected
(refer to Supported Resolutions).
114
Check the followings.
Installation issue (PC mode)
The screen keeps switching on and off.
Check the cable connection between the product and PC, and ensure the connection is secure.
Blank spaces are found on all four sides of the screen when
an HDMI or HDMI-DVI cable is connected to the product and
PC.
The blank spaces found on the screen have nothing to do with the product.
Blank spaces on the screen are caused by the PC or graphics card. To resolve the problem, adjust the
screen size in the HDMI or DVI settings for the graphics card.
If the graphics card settings menu does not have an option to adjust the screen size, update the
graphics card driver to the latest version.
(Please contact the graphics card or computer manufacturer for further details about how to adjust
the screen settings.)
PC is shown in Source when a PC is not connected.
PC is always shown in Source irrespective of whether or not a PC is connected.
Screen issue
The power LED is off. The screen will not switch on.
Make sure that the power cord is connected.
No Signal is displayed on the screen.
Check that the product is connected correctly with a cable.
Check that the device connected to the product is powered on.
Not Optimum Mode is displayed.
This message is displayed when a signal from the graphics card exceeds the product's maximum
resolution and frequency.
Refer to the Standard Signal Mode Table and set the maximum resolution and frequency according to
the product specifications.
The images on the screen look distorted.
Check the cable connection to the product.
115
Screen issue
The screen is not clear. The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension cable, etc) and try again.
Set the resolution and frequency to the recommended level.
The screen appears unstable and shaky.
There are shadows or ghost images left on the screen.
Check that the resolution and frequency of the PC and graphics card are set within a range compatible
with the product. Then, change the screen settings if required by referring to the Additional
Information on the product menu and the Standard Signal Mode Table.
The screen is too bright. The screen is too dark.
Adjust Brightness and Contrast.
Screen colour is inconsistent.
Go to Picture and adjust the Colour Space settings.
White does not really look white.
Go to Picture and adjust the White Balance settings.
There is no image on the screen and the power LED blinks
every 0.5 to 1 second.
The product is in power-saving mode.
The product will turn off automatically.
Go to System and make sure Sleep Timer is set to Off.
Press any key on the keyboard or move the mouse to return to the previous screen.
If a PC is connected to the product, check the power status of the PC.
Make sure the power cable is connected properly to the product and power outlet.
If the signal from a connected device is not detected, the product automatically turns off after 10 to 15
minutes.
Picture quality of the product is different from the dealer
shop where it was purchased.
Use an HDMI cable to obtain high-definition (HD) picture quality.
116
Screen issue
The screen display does not look normal.
Encoded video content may cause the display to appear corrupted in scenes featuring fast moving
objects such as in a sports event or action video.
Low signal level or low picture quality may cause the display to appear corrupted. This does not mean
the product is defective.
A cell phone within a distance of one-meter radius may cause static on analogue and digital products.
The brightness and colour do not look normal.
Go to Picture and adjust the screen settings such as Picture Mode, Colour, Brightness and
Sharpness.
Go to System and adjust the Energy Saving settings.
Reset the screen settings to the default settings.
Broken lines are displayed on the edges of the screen.
If Picture Size is set to Screen Fit, change the setting to 16:9.
Lines (red, green or blue) are displayed on the screen.
These lines are displayed when there is a defect in DATA SOURCE DRIVER IC on the monitor. Contact a
Samsung Service Centre to resolve the issue.
The display looks unstable and then freezes.
The screen may freeze when a resolution other than the recommended resolution is used or if the
signal is not stable. To resolve the issue, change the PC resolution to the recommended resolution.
The screen cannot be displayed in full screen.
A scaled SD (4:3) content file can cause black bars on both sides of an HD channel screen.
A video with an aspect ratio different from the product can cause black bars at the top and bottom of
the screen.
Change the screen size setting to full screen on the product or source device.
117
Sound issue
There is no sound.
Check the connection of the audio cable or adjust the volume.
Check the volume.
The volume is too low.
Adjust the volume.
If the volume is still low after turning it up to the maximum level, adjust the volume on your PC sound
card or software programme.
Video is available but there is no sound.
If an HDMI cable is connected, check the audio output settings on the PC.
Go to Sound and change Speaker Select to Internal.
If a source device is used
•• Make sure the audio cable is properly connected to the audio input port on the product.
•• Check the audio output settings for the source device.
(For example, if an HDMI cable is connected to the monitor, the audio setting for the cable box
may need to be changed to HDMI.)
If a DVI-HDMI cable is used, a separate audio cable is required.
If the product has a headphone port, make sure nothing is connected to it.
Reconnect the power cable to the device and then reboot the device.
There is static coming from the speakers.
Check the cable connection. Make sure a video cable is not connected to an audio input port.
Check the signal strength after connecting a cable.
Low signal level can cause corrupted sound.
118
Sound issue
There is audible sound when the volume is muted.
When Speaker Select is set to External, the volume button and mute function are disabled.
Adjust the volume for the external speakers.
Audio settings for main speakers are separate from the internal speakers on the product.
Changing or muting the volume on the product does not affect an external amplifier(decoder).
Sound from the monitor does not change after Sound Mode
is changed.
Audio settings for main speakers are separate from the internal speakers on the product.
There is an echo sound coming from the speakers.
Different decoding speeds between the product speakers and external speakers can cause an echo.
Audio settings on a source device do not affect the internal speaker settings on the product.
In this case, set Speaker Select to External.
Remote control issue
The remote control does not work.
Make sure that the batteries are correctly in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is connected.
Check for any special lighting or neon signs switched on in the vicinity.
Source device issue
A beeping sound is heard when my PC is booting.
If a beeping sound is heard when your PC is booting, have your PC serviced.
119
Other issue
Small particles are found on the edges of the product.
The particles are part of the product design. The product is not defective.
The PIP menu is not available.
The menu is enabled or disabled depending on the Source mode.
When I try to change the PC resolution, a message "The
defined resolution is not supported." appears.
The message "The defined resolution is not supported." appears if the input source resolution
exceeds the maximum resolution of the display.
To resolve the issue, change the PC resolution to a resolution supported on the display.
There is no sound from the speakers in HDMI mode when a
DVI-HDMI cable is connected.
DVI cables do not transmit sound data.
HDMI Black Level is not functioning properly on an HDMI
device with YCbCr output.
This function is available only when a source device, such as a DVD player and STB, is connected to the
product via an HDMI (RGB signal) cable.
There is no sound in HDMI mode.
Displayed picture colours may not look normal. Video or sound may not be available. This can occur if
a source device that only supports an older version of the HDMI standard is connected to the product.
Make sure to connect the audio cable to the correct input jack to enable audio.
If these issues occur, connect an audio cable along with the HDMI cable.
Some PC graphics cards may not automatically recognize HDMI signals that do not include sound. In
this case, manually select a sound input.
Sound input
Screen mode
PC
Auto
PC settings
DVI PC
Audio In(Stereo ports)
PC settings
120
Other issue
The IR sensor is not functioning.
Make sure the sensor light turns on when a button is pressed on the remote control.
•• If the sensor light does not turn on, turn the power switch off and then on again on the back of
the product.
(The power LED lights up red when the screen is switched off.)
If the sensor light still does not turn on after the power switch is turned off and then on again, an
internal jack may be disconnected.
Contact your nearest service centre to have the product serviced.
•• If the sensor light that is on does not flash red when a button is pressed on the remote control,
the IR sensor may be defective.
Contact your nearest service centre to have the product serviced.
•• If there is no change on the screen when a button is pressed on the remote control although the
sensor light flashes red, the mainboard may be defective.
Contact your nearest service centre to have the product serviced.
121
Q&A
Question
How can I change the frequency?
Answer
Set the frequency on your graphics card.
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
resolution → Advanced Settings → Monitor and adjust the frequency in Monitor Settings.
•• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust resolution → Advanced Settings → Monitor and adjust the frequency in Monitor
Settings.
Refer to the user manual for your PC or
graphics card for further instructions on
adjustment.
•• Windows 10: Go to Settings → System → Display → Advanced display settings → Display
adapter properties → Monitor, and adjust Screen refresh rate under Monitor settings.
How can I change the resolution?
•• Windows 7: Go to Control Panel → Appearance and Personalization → Display → Adjust
Resolution and adjust the resolution.
•• Windows 8: Go to Settings → Control Panel → Appearance and Personalization → Display
→ Adjust Resolution and adjust the resolution.
•• Windows 10: Go to Settings → System → Display → Advanced display settings, and adjust
the resolution.
How do I set powersaving mode?
•• Windows 7: Set power-saving mode in Control Panel → Appearance and Personalization →
Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•• Windows 8: Set power-saving mode in Settings → Control Panel → Appearance and
Personalization → Personalize → Screen Saver Settings or BIOS SETUP on the PC.
•• Windows 10: Set power-saving mode in Settings → Personalization → Lock screen → Screen
timeout settings → Power & sleep or BIOS SETUP on the PC.
122
Chapter 13
Specifications
-
General
Size
Model Name
Panel
-
Display area
ED65E / EM65E
ED75E / EM75E
Size
65 CLASS (64.5 inches / 163 cm)
75 CLASS (74.5 inches / 189 cm)
Display area
1428.48 mm (H) x 803.52 mm (V)
1650.24 mm (H) x 928.26 mm (V)
56.2 inches (H) x 31.6 inches (V)
65.0 inches (H) x 36.5 inches (V)
10 W + 10 W
10 W + 10 W
H
Audio Output
V
Model Name
Panel
Audio Output
DC32E / DC32E-M
DC40E / DC40E-M / DC40E-H
Size
32 CLASS (31.5 inches / 80.1 cm)
40 CLASS (40.0 inches / 101.6 cm)
Display area
698.4 mm (H) x 392.85 mm (V)
885.6 mm (H) x 498.15 mm (V)
27.5 inches (H) x 15.5 inches (V)
34.9 inches (H) x 19.6 inches (V)
10 W
10 W + 10 W
123
Model Name
Panel
DC48E / DC48E-M / DC48E-H
DC55E / DC55E-M
Size
48 CLASS (47.6 inches / 120.9 cm)
55 CLASS (54.6 inches / 138.7 cm)
Display area
1054.08 mm (H) x 592.92 mm (V)
1209.6 mm (H) x 680.4 mm (V)
41.5 inches (H) x 23.3 inches (V)
47.6 inches (H) x 26.8 inches (V)
Audio Output
10 W + 10 W
10 W + 10 W
Power Supply
This product uses 100 to 240V. Refer to the label at the back of the product as the standard voltage can vary in
different countries.
Environmental
considerations
Operating
Temperature : 0 C - 40 C (32 F - 104 F)
Humidity : 10% - 80%, non-condensing
Storage
Temperature : -20 C - 45 C (-4 F - 113 F)
Humidity : 5% - 95%, non-condensing
――Plug-and-Play
This monitor can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the monitor and PC system optimizes the monitor
settings. Monitor installation takes place automatically. However, you can customize the installation settings if desired.
――Panel Dots (Pixels)
Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel. This does not affect
product performance.
――This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
――For detailed device specifications, visit the Samsung Electronics website.
124
Preset Timing Modes
――This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than
the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product.
Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product. If the LCD product does not support 85Hz, change the vertical
frequency to 60Hz using the CDT product before you exchange it with the LCD product.
Synchronization
Resolution
-- Horizontal Frequency
The time required to scan a single line
from the left to the right side of the
screen is called a horizontal cycle. The
reciprocal number of a horizontal cycle
is called horizontal frequency. Horizontal
frequency is measured in kHz.
-- Vertical Frequency
The product displays a single image
multiple times per second (like a
fluorescent light) to display what the
viewer sees. The rate of a single image
being displayed repeatedly per second is
called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
Horizontal Frequency
30 – 81 kHz
Vertical Frequency
48 – 75 Hz
Optimum resolution
1920 x 1080 @ 60 Hz
Maximum resolution
1920 x 1080 @ 60 Hz
The screen will automatically be adjusted if a signal that belongs to the following standard signal modes is transmitted from your PC. If the signal transmitted from the PC
does not belong to the standard signal modes, the screen may be blank with the power LED on. In such a case, change the settings according to the following table by
referring to the graphics card user manual.
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
IBM, 720 x 400
31.469
70.087
28.322
-/+
MAC, 640 x 480
35.000
66.667
30.240
-/-
MAC, 832 x 624
49.726
74.551
57.284
-/-
MAC, 1152 x 870
68.681
75.062
100.000
-/-
VESA, 640 x 480
31.469
59.940
25.175
-/-
VESA, 640 x 480
37.861
72.809
31.500
-/-
VESA, 640 x 480
37.500
75.000
31.500
-/-
VESA, 800 x 600
35.156
56.250
36.000
+/+
VESA, 800 x 600
37.879
60.317
40.000
+/+
125
Resolution
Horizontal Frequency
(kHz)
Vertical Frequency
(Hz)
Pixel Clock
(MHz)
Sync Polarity
(H/V)
VESA, 800 x 600
48.077
72.188
50.000
+/+
VESA, 800 x 600
46.875
75.000
49.500
+/+
VESA, 1024 x 768
48.363
60.004
65.000
-/-
VESA, 1024 x 768
56.476
70.069
75.000
-/-
VESA, 1024 x 768
60.023
75.029
78.750
+/+
VESA, 1152 x 864
67.500
75.000
108.000
+/+
VESA, 1280 x 720
45.000
60.000
74.250
+/+
VESA, 1280 x 800
49.702
59.810
83.500
-/+
VESA, 1280 x 1024
63.981
60.020
108.000
+/+
VESA, 1280 x 1024
79.976
75.025
135.000
+/+
VESA, 1366 x 768
47.712
59.790
85.500
+/+
VESA,1440 x 900
55.935
59.887
106.500
-/+
VESA,1600 x 900 RB
60.000
60.000
108.000
+/+
VESA,1680 x 1050
65.290
59.954
146.250
-/+
VESA,1920 x 1080
67.500
60.000
148.500
+/+
126
Chapter 14
Appendix
Responsibility for the Pay Service
(Cost to Customers)
――When the service is requested, in spite of in warranty, we may charge you for a visit from a service
technician in the following cases.
Not a product defect
Cleaning of the product, Adjustment, Explanation, Re-installation and etc.
•• If a service technician gives instructions on how to use product or simply adjusts options without
disassembling product.
•• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.)
•• If a product is reinstalled or devices are connected additionally after installing the purchased
product for the first time.
•• If a product is reinstalled to move to a different spot or to move to a different house.
•• If customer requests instructions on how to use because of another company's product.
•• If customer requests instructions on how to use the network or another company's programme.
•• If customer requests software installation and setup for the product.
A Product damage caused by customer's fault
Product damage caused by customer's mishandling or wrong repair
If a product damage is caused by;
•• External impact or drop.
•• Use of supplies or separatly sold product unspecified by Samsung.
•• Repair from a person besides an engineer of outsourcing service company or partner of Samsung
Electronics Co., Ltd.
•• Remodeling or repairing the product by customer.
•• Using it with incorrect voltage or non-authorised electrical connections.
•• Not following the "cautions" in User Manual.
Others
•• If product fails by natural disaster. (lightning, fire, earthquake, flood damage, etc)
•• If consumable components are all used up. (Battery, Toner, Fluorescent lights, Head, Vibrator, Lamp,
Filter, Ribbon, etc.)
――If customer requests a service in case the product has no defect, service fee may be charged. So
please read User Manual first.
•• If a service technician removes/cleans dusts or foreign materials inside of the product.
•• If customer requests an installation additionally after purchasing a product through homeshopping or online.
127
Optimum Picture Quality and Afterimage
Burn-in Prevention
Black Matrix
Common
Electrode (ITO)
Colour-Filter
Optimum Picture Quality
•• Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm)
may be brighter or darker on the panel. This does not affect product performance.
-- The number of sub-pixels by panel type: 6,220,800
Source
Drain
•• Run Auto Adjustment to improve the picture quality. If noise is still found even after auto
adjustment, adjust Coarse or Fine.
•• Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage
burn-in or defective pixels.
-- Activate power-saving mode or a dynamic screen saver if you will not be using the product for
an extended period of time.
Gate
TFT
Pixel Electrode (ITO)
Storage
Capaccitor (Cs)
Data Bus-Line
Prevention of Afterimage Burn-in
What is afterimage burn-in?
Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers
to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period
of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that
control the liquid crystals.
Such a voltage difference between electrodes increases with time and makes the liquid crystals thinner.
When this occurs, a previous image can remain on the screen when the pattern changes. To prevent this,
the accumulated voltage difference should be reduced.
――Afterimage burn-in should not occur when an LCD panel is operating in proper conditions.
128
Preventing afterimage burn-in
――The best way to protect the product from afterimage burn-in is switching the power off or setting the
PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending
on instruction guide.
•• Powering Off, Screen Saver and Power Saving Mode
-- Power off the product for 2 hours after using it for 12 hours.
-- Go to Display Properties > Power Supply on your PC and set the product to power off as
required.
-- Using a screen saver is recommended.
It is best to use a single-colour or moving-image screen saver.
FLIGHT : TIME
OZ348
: 20:30
FLIGHT : TIME
OZ348
•• Regular colour Change
-- Use 2 colours
Switch between 2 colours every 30 minutes as shown above.
Type 1
•• Regular Text colour Change
-- Use bright colours of similar brightness.
Interval: Change text colour and background colour every 30 minutes
: 20:30
FLIGHT : TIME
OZ348
: 20:30
FLIGHT : TIME
OZ348
: 20:30
-- Move and change text every 30 minutes as shown below.
Type 2
FLIGHT
TIME
FLIGHT
TIME
OZ348
20:30
OZ348
20:30
UA102
21:10
UA102
21:10
•• Avoid combinations of a text colour and background colour of contrasting brightness.
(Brightness: refers to the lightness or darkness of a colour which varies depending on the amount of
light emitted.)
――Avoid using grey as it may contribute to afterimage burn-in.
――Avoid using colours of contrasting brightness (black and white; grey).
FLIGHT : TIME
FLIGHT : TIME
OZ348 : 20:30
OZ348 : 20:30
FLIGHT
: TIME
OZ348
: 20:30
[ Step 1 ]
[ Step 2 ]
FLIGHT
: TIME
OZ348
: 20:30
[ Step 3 ]
-- Regularly display a moving image along with a logo.
Interval: Display a moving image along with a logo for 60 seconds after using for 4 hours.
129
Licence
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby Laboratories.
This DivX CertifiedⓇ device has passed rigorous testing to ensure it plays
DivXⓇ video.
To play purchased DivX movies, first register your device at vod.divx.com. Find
your registration code in the DivX VOD section of your device setup menu.
®
Premium Sound 5.1
®
Studio Sound
Manufactured under a license from U.S. Patent No’s: 5,956,674, 5,974,380,
5,978,762, 6,487,535, 6,226,616, 7,212,872, 7,003,467, 7,272,567, 7,668,723,
7,392,195, 7,930,184, 7,333,929 and 7,548,853. DTS, the Symbol, and DTS and
the Symbol together are registered trademarks & DTS Premium Sound | 5.1 is a
trademark of DTS, Inc. ⓒ2012 DTS, Inc. All Rights Reserved.
Manufactured under a license from U.S. Patent No’s: 6,285,767, 8,027,477,
5,319,713, 5,333,201, 5,638,452, 5,771,295, 5,970,152, 5,912,976, 7,200,236,
7,492,907, 8,050,434, 7,720,240, 7,031,474, 7,907,736 and 7,764,802. DTS, the
Symbol, and DTS and the Symbol together are registered trademarks & DTS
Studio Sound is a trademark of DTS, Inc. ⓒ2012 DTS, Inc. All Rights Reserved.
DivX CertifiedⓇ to play DivXⓇ video up to HD 1080p, including premium content.
DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of DivX, LLC and are used under
license.
Covered by one or more of the following U.S. patents: 7,295,673; 7,460,668; 7,515,710; 8,656,183;
8,731,369; RE45,052.
Open Source Licence Notice
In the case of using open source software, Open Source Licences are available on the product menu.
Open Source Licence Notice is written only English.
For information on the Open Source Licence Notice, contact the Samsung Customer Centre or send
email to oss.request@samsung.com.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the
HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in
the United States and other countries.
130
Terminology
480i / 480p / 720p / 1080i /
1080p____ Each of the scanning
rates above refers to the number of
effective scanning lines that decides
the screen resolution. The scanning
rate may be indicated in i (interlaced)
or p (progressive), depending on the
scanning method.
- Scanning
Scanning refers to a process of sending
pixels that form an image progressively.
A larger number of pixels will deliver a
clearer and more vivid picture.
- Progressive
In progressive scan mode, all lines
of pixels are scanned one by one
(progressively) on the screen.
- Interlaced
In interlaced scan mode, every other
line of pixels is scanned from top to
bottom first and then the remaining
lines of pixels (that were not scanned)
are scanned.
Non-interlace Mode and Interlace
Mode____ Non-interlace mode
(progressive scan) displays a horizontal
line from the top to the bottom of a
screen progressively. Interlace mode
displays the odd number lines first
and the even number lines next. Noninterlace mode is mainly used in
monitors as it produces screen clarity
and interlace mode is mainly used in
TVs.
Dot Pitch____ The product and screen
consist of red, green and blue dots.
A shorter distance between the dots
produces a higher resolution. Dot pitch
refers to the distance between the
shortest distance between dots of the
same colour. Dot pitch is measured in
millimeters.
Vertical Frequency____ The product
displays a single image many times
per second (like a fluorescent light that
flickers) to display an image for a viewer
to see. The rate of a single image being
displayed repeatedly per second is
called vertical frequency or refresh rate.
Vertical frequency is measured in Hz.
E.g. 60Hz refers to a single image being
displayed 60 times in one second.
Horizontal Frequency____ The time
required to scan a single line from the
left to the right side of the screen is
called a horizontal cycle. The reciprocal
number of a horizontal cycle is called
horizontal frequency. Horizontal
frequency is measured in kHz.
Source____ Input source refers to a
video source device connected to the
product such as a camcorder or video
or DVD player.
Component ports (green, blue and
red)____ The component ports, which
identify, transmit and receive contrast
signals, provide superior picture quality
to any other video connection methods.
Plug & Play____ Plug & Play is a
function that allows the automatic
exchange of information between a
monitor and PC to produce an optimum
display environment. The product uses
VESA DDC (international standard) to
execute Plug & Play.
Resolution____ Resolution is the
number of horizontal dots (pixels) and
vertical dots (pixels) that form a screen.
It represents the level of display detail.
A higher resolution enables more
data to be displayed on the screen
and is useful to perform multiple tasks
simultaneously.
E.g. A resolution of 1920 X 1080 consists
of 1,920 horizontal pixels (horizontal
resolution) and 1,080 vertical pixels
(vertical resolution).
HDMI (High Definition Multimedia
Interface)____ It is an interface that
can be connected to a digital audio
source as well as a high-definition video
source by using a single cable without
compression.
Multiple Display Control (MDC)____
MDC (Multiple Display Control) is an
application that allows multiple display
devices to be controlled simultaneously
using a PC. Communication between
a PC and monitor takes place using
RS232C (serial data transmission) and
RJ45 (LAN) cables.
131
Download PDF