Samsung | MX-E870 | Samsung MX-E870 User Manual

MX-E850
MX-E851
MX-E870
MX-E871
Three-CD Changer
MINI-Compact System
MP3-CD/WMA-CD/CD-R/RW Playback
user manual
Imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous voltage” inside CAUTION : TO PREVENT ELECTRIC SHOCK, This symbol indicates important instructions
the product that presents a risk of electric shock or MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY accompanying the product.
personal injury.
INSERT.
WARNING
• To reduce the risk of fire or electric shock, do not
expose this appliance to rain or moisture.
CAUTION
• Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
• The Mains plug is used as a disconnect device and shall
stay readily operable at any time.
• This apparatus shall always be connected to an AC outlet
with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug
must be pulled out from the mains socket, therefore the
mains plug shall be readily operable.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1 PRODUCTO
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1
LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein may result in
hazardous radiation exposure.
CAUTION
• INVISIBLE
LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
Accessories
Check for the supplied accessories below.
FM Antenna
Spacers ( 8 EA)
(MX-E870/E871 only)
User's Manual
Remote Control/Batteries(Optional)
Back bracket 4 EA /Screws 16 EA
(MX-E870/E871 only)
AM Antenna (Optional)
Connector-Adaptor(Optional)
• Figures and illustrations in this User Manual are provided for reference only and may differ from actual product
appearance.
• An administration fee may be charged if either
a. an engineer is called out at your request and there is no defect in the product
(i.e. where you have failed to read this user manual)
b. you bring the unit to a repair centre and there is no defect in the product
(i.e. where you have failed to read this user manual).
• The amount of such administration charge will be advised to you before any work or home visit is carried out.
2
Symbols
English
Important
Note
Precautions
• Ensure that the AC power supply in your house complies
with the identification sticker located on the back of your
product.
• Install your product horizontally, on a suitable base (furniture),
with enough space around it for ventilation (7.5~10cm).
• Do not place the product on amplifiers or other equipment
which may become hot. Make sure the ventilation slots are
not covered.
• Do not stack anything on top of the product.
• Before moving the product, ensure the Disc Insert Hole is
empty.
• In order to disconnect the product completely from the
power supply, remove the AC plug from the wall outlet,
especially when left unused for a long period of time.
• During thunderstorms, disconnect the AC plug from the wall
outlet. Voltage peaks due to lightning could damage the
product.
• Do not expose the product to direct sunlight or other heat
sources. This could lead to overheating and malfunction of
the product.
• Protect the product from moisture, and excess heat or
equipment creating strong magnetic or electric fields (i.e.
speakers.).
• Disconnect the power cable from the AC supply if the
product malfunctions. Your product is not intended for
industrial use.
• Use of this product is for personal use only.
• Condensation may occur if your product or disc has been
stored in cold temperatures. If transporting the product
during the winter, wait approximately 2 hours until the
product has reached room temperature before using.
• The batteries used with this product contain chemicals that are harmful to the environment. Do not dispose of batteries in the general household trash.
• Maintain an open space of approximately 6 inches (15 cm) on the sides and rear of the system, for ventilation purposes.
• Place the loudspeakers at a reasonable distance on either side of the system to ensure good stereo sound.
• Direct the loudspeakers towards the listening area.
Disc Storage
• Do not keep in direct sunlight
• Keep in a cool ventilated area
• Keep in a clean Protection jacket.
Store vertically.
• Do not allow the discs to become contaminated with dirt.
• Do not load cracked or scratched discs.
Handling and Storing Discs
If you get fingerprints or dirt on the disc, clean it with a
mild detergent diluted in water and wipe with a soft cloth.
• When cleaning, wipe gently from the inside to the outside of
the disc
• Condensation may form if warm air comes into contact
with cold parts inside the product. When condensation
forms inside the product, it may not operate correctly. If this
occurs, remove the disc and let the product stand for 1 or 2
hours with the power on.
Disc Types And Disc Format
This product does not support Secure (DRM) Media files.
CD-R Discs
• Some CD-R discs may not be playable depending on
the disc recording device (CD-Recorder or PC) and the
condition of the disc.
• Use a 650MB/74 minute CD-R disc. Do not use CD-R discs over 700MB/80 minutes as they
may not be played back.
• Some CD-RW (Rewritable) media, may not be playable.
• Only CD-Rs that are properly "closed" can be fully played. If
the session is closed but the disc is left open, you may not
be able to fully play the disc.
CD-R MP3 Discs
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound and picture
quality or cause skipping.
Be especially careful not to scratch discs when handling
them.
Holding discs
• Do not touch the playback side of the disc.
• Hold the disc by the edges so that fingerprints will not get
on the surface.
• Do not stick paper or tape on the disc.
• Only CD-R discs with MP3 files in ISO 9660 or Joliet format
can be played.
• MP3 file names should contain no blank spaces or special
characters (. / = +).
• Use discs recorded with a compression/decompression
data rate greater than 128Kbps.
• Only files with the ".mp3" and ".MP3" extensions can be
played.
• Only a consecutively written multisession disc can be
played. If there is a blank segment in the Multisession disc,
the disc can be played only up to the blank segment.
• If the disc is not closed, it will take longer to begin playback
and not all of the recorded files may be played.
• For files encoded in Variable Bit Rate (VBR) format, i.e. files
encoded in both low bit rate and high bit rate (e.g., 32Kbps
~ 320Kbps), the sound may skip during playback.
• A maximum of 999 tracks can be played per CD.
• Supported Audio Formats:WMA 56~128kbps Bit rate.
English
2
3
Contents
Thank you for buying this SAMSUNG mini-compact system.
Please take time to read these instructions.
They will allow you to operate your system with ease and take full advantage of its features.
Safety Warnings.............................................2
Accessories....................................................2
Precautions....................................................3
Cautions on Handling and
Storing Discs..................................................3
Disc Types And Disc Format.........................3
Contents.........................................................4
Description.....................................................4
Top Panel..................................................4
Front Panel...............................................5
Rear Panel................................................6
Remote Control........................................7
Display function.............................................7
Connecting Microphone................................8
Stacking the Speakers (MX-E870/E871 Only).........8
Loading and Changing Compact Discs...........9
CD/MP3/WMA-CD Playback........................9
Selecting a CD in the Disc changer............10
Selecting a Track..........................................10
Searching a Track/Folder Quickly...............10
Searching for a Specific Music
Passage on a CD.........................................10
Repeat One or All Tracks on the
Compact Discs.............................................10
A-B Repeat Playback..................................10
10 Skip Function..........................................11
CD Programming.........................................11
Checking or Editing the
Programmed Tracks....................................11
Auto Change function..................................11
Playing USB.................................................12
To Select a Track from USB Device......12
To Search a Folder Quickly...................12
To repeat.................................................12
To Use High Speed Search...................12
To delete a file........................................12
To skip next 10 tracks............................12
Listening a Radio.........................................13
Selecting a Stored Station...........................13
Setting the Clock.........................................13
Timer Function.............................................14
Cancelling the Timer....................................14
Recording Function.....................................15
Recording Speed.........................................15
Selecting EQ Mode.....................................16
Selecting USER EQ Mode...........................16
Using the DYNAMIC SPOT Mode...............16
Using the Stadium Mode.............................16
GIGA SOUND function.................................16
LED LIGHTING function...............................16
Party function...............................................17
Troubleshooting...........................................17
Specifications...............................................18
Description
Top Panel
1
2
4
English
1. LED LIGHTING control
2. LED LIGHTING
Description
Front Panel
2
34
33
32
3
4
5
31
30
1
6
29
28
27
26
25
7
8
9
10
11
12
13
24
23
22
14
15
16
17
18 19 20
1.
POWER button
• Press this button to switch your mini-compact system.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
LED LIGHTING button
Window display
EASY SEARCHING JOG control
Search/Skip button
MP3/CD button
TUNER/AUX button
EQ button
AUTO CHANGE button
PARTY button
STOP button
RETURN button
DELETE button
DISC CHANGE button
DISC seletion button
DISC tray
USB 1 jack
MIC jack
AUX IN 1 jack
Connecting an External Component such as an MP3 player.
• Connect AUX IN 1 on the front panel of the MINI
COMPACT to the Audio Out of the external
component/MP3 player.
• Press the TUNER/AUX button to select the AUX 1 input.
You can select AUX 1 by pressing the FUNCTION button
on the remote control.
21
20. PHONE jack
Plug a headphones with a 3.5ø jack into the PHONE jack.
• The speakers are no longer used to output the sound.
• Prolonged use of headphones at a high volume may
damage your hearing.
• If you use the headphones, GIGA SOUND will
automatically turn off. Even if you remove the
headphones, it will not turn on.
21. USB 2 REC jack
22. OPEN/CLOSE button
23. ENTER button
24. PLAY/PAUSE button
25. REC SPEED button
26. USB 2 REC button
27. USER EQ button
28. USB 2 button
29. USB 1 button
30. Search/Skip button
31. MASTER VOLUME control
32. STADIUM button
33. DYNAMIC SPOT button
34. GIGA SOUND BLAST button
English
4
5
Rear Panel
1. 2.1CH Speaker Connector Terminals
(MX-E850/E851)
4.2CH Speaker Connector Terminals
(MX-E870/E871)
MX-E850/E851
The speakers connector terminals are located on the rear of
the system.
1. To achieve the correct sound quality, insert those speaker
connector cables to the speaker connector terminals of
the system.
• Left speaker (marked L).
• Right speaker (marked R).
• The Rear speakers are only for MX-E870/E871.
8
7
2. LED Terminals of the Front Speakers
3. ONLY FOR SERVICE
• This jack is just for testing, please don't use it.
4. AUX IN 2 Terminals
1. Use the Audio Cable (not supplied) to connect AUX IN 2
on the product to Audio Out on the external analog component.
1
2
3
4
• B
e sure to match connector colors.
• If the external analog component has only one Audio Out
jack, connect either left or right.
5 6 5
• Press the TUNER/AUX button to select the AUX 2 input.
• You can select AUX 2 by pressing the FUNCTION button
on the remote control.
MX-E870/E871
5. FM Antenna Connector Terminal
The position of FM antenna connector terminal may differ
8
7
depending on your region.
This product may not support the AM function depending on
your region.
1. Connect the FM antenna (supplied) to the FM Antenna
jack.
2. Slowly move the antenna wire around until you find a
location where reception is good, then fasten it to a
wall or other rigid surface.
3. If reception is poor, you may need to install an outdoor
antenna. To do so, connect an outdoor FM antenna to
the FM socket on the rear of the system using a 75Ω
coaxial cable (not supplied).
6. AM Antenna Connector Terminal (Optional)
This product may not support the AM function depending on
your region.
1. Plug the connector on the AM antenna (Optional) into
the AM terminal on the rear of the system.
7. Voltage Selector (Optional)
1
2
3
4
5 6 5
Check the position of the voltage selector on the rear of the
system(optional).
This product may not support the Voltage Selector function
depending on your region.
8. Cooling fan
• The fan always turns when the power is on. Secure a minimum 10 cm of clear space from all sides of the fan
when installing the product.
6
English
Remote Control
33
1
32
2
3
31
4
5
6
30
29
7
8
9
10
11
12
13
14
15
16
17
18
28
27
26
25
24
23
22
21
20
19
1.
2.
3.
4.
POWER
DISPLAY
USB
Number(0~9) button
• During playback,
press the desired track
number. The selected
track is played.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
-10
Skip, RDS PTY *
STOP
PLAY
DELETE
SOUND
ENTER
VOLUME TUNING/ALBUM .
MO/ST
TIMER ON/OFF
TIMER SET
SLEEP
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
MY KARAOKE
MIC VOLUME -, +
REPEAT A-B
REPEAT
TUNING MODE
VOLUME +
TUNING/ALBUM ,
EQ
CD REC SPEED
USB REC
PAUSE
SEARCH, RDS DISPLAY*
+10
CD DISC SKIP*
FUNCTION
MUTE
• Turn off the sound
temporarily.
• Set a sleep time to
shut off the product.
*This product is not used the RDS PTY and RDS DISPLAY function printed the [, ) button above.
Display function
Installing batteries in the Remote
Control
`` Place batteries in the remote control so they match the
polarity : (+) to (+) and (–) to (–).
`` Always replace both batteries at the same time.
`` Do not expose the batteries to heat or a flame.
`` The remote control can be used up to approximately 23 feet
(7 meters) in a straight line.
You can view all functions available on the display,
adjust the brightness of the display and select the
Display/LED either on or off.
Each time you press the DISPLAY button on the
remote control, the display mode will change as following:
◆◆ The Demo function
All functions available on the system appear on the
front panel display.
◆◆ The Dimmer function
The Dimmer function is selected and the display
darkens.
◆◆ LED OFF
The LED is turned off while the dimmer function .
is working.
◆◆ Clock ON
The Clock you set is displayed.
◆◆ LED/Display ON
ALL Display and LED turned on.
* Battery size: AAA
English
6
7
Connecting Microphone
You can also insert microphone to sing along with
your favorite CDs.
1. Connect the microphone to the MIC jack on the
front of the product.
`` If your microphone with a larger jack than 3.5ø
MIC jack, you need a ConnectorAdaptor(optional) to complete the connection.
• First, connect the Connector-Adaptor to
the MIC jack on the front of the product,
• Second, connect the microphone (with
larger jack) to the Connector-Adaptor.
2. Press the MIC VOL-, + button to adjust the
volume of the microphone.
3. Press the MY KARAOKE button to suppress the
Vocal. Each time the button is pressed, the
selection is changed as follows: KARAOK OFF ➞
KARAOK MIN ➞ KARAOK MAX.
`` If you hear strange noises (squealing or howling) while
using the Karaoke feature, move the microphone
away from the speakers. Turning down the
microphone's volume or the speaker volume is also
effective.
`` The microphone does not operate in the AUX,
TUNER mode.
`` If you connect with the Microphone, GIGA SOUND
will automatically turn off. Even if you remove the
microphone, it will not turn on.
`` After setting my karaoke, EQ/GIGA SOUND does not
work.
`` After the stop operation, the setting of my karaoke
will disappear.
`` Only when connected with a Microphone, the MY
KARAOKE function is available.
Stacking the Speakers (MX-E870/E871 Only)
You can stack and install the speakers as
described in the figure.
1. Insert 2 spacers into the holes of the Subwoofer (L)
and fix them.
Spacer
Subwoofer Speaker
2. Stack the Front Speaker(L) horizontally on the
Subwoofer(L).
8
English
3. Insert 2 spacers into the holes of the Front Speaker(L)
and fix them.
Spacer
Front Speaker
Subwoofer Speaker
4. Stack the Rear Speaker(L) on the Front Speaker (L).
5. To fix the speakers securely, attach the back bracket
on the rear of the Front speaker(L), Rear speaker (L)
and Subwoofer speaker by fastening provided 8
screws.
Rear Speaker
Back bracket
Front Speaker
Subwoofer Speaker
* The rear of the stacked speakers
◆◆Follow steps 1-5 above to stack the Right Speakers.
6. This is the completion of the speaker stack.
Loading and Changing Compact Discs
You can play 12 cm compact disc without an adapter.
force the compact disc carrousel when opening
☛☛ Nandeverclosing
the disc tray.
Never press down or place objects on the carrousel.
1. P
ress the OPEN/CLOSE button on the main unit.
Result: The disc tray opens.
2. P
lace one disc in the front slots of the carrousel,
with the label on the discs facing upwards.
☛☛ Check that the compact disc has been cor-
rectly inserted in the holder before closing the
disc disc tray.
3. If you wish to load another compact disc, press the
DISC CHANGE button on the main unit.
Result: The carrousel rotates by 120°.
4. C
lose the disc tray by pressing the OPEN/CLOSE
button again.
Result: Playback starts automatically.
➣➣To change or unload the compact discs, repeat
step 2 to 4.
• Keep the disc tray closed whenever you are not
using it, to prevent dust from entering.
• Do not use force when closing the disc tray, as it
may cause damage to the the disc tray.
• You can load or unload compact discs when the
radio, USB or auxiliary source function is selected,
and when you press the Open/Close button, all of
the other functions will be changed to the MP3/CD
mode.
• If no buttons are pressed on the product or remote
control for more than 3 minutes when the product is
in Pause mode, it will be changed to Stop mode.
• If no buttons are pressed on the product or remote
control for more than 25 minutes when the product
is in Stop mode, the power will automatically turn
off.
CD/MP3/WMA-CD Playback
☛☛This product is designed to play an audio CD, CD, CD-R, CD-RW, MP3/WMA-CD.
• G
ently open or close the CD tray and do not apply
excessive force.
• Do not put force or place a heavy object on the product.
• Do not insert an out-of-spec. shape of CD such as a
heart or octangle shaped CD. Otherwise, the product
may be damaged.
• Care must be taken about maintenance of the compact
discs.
• At least more than one CD should be inserted for
playbacks.
1. Press the OPEN/CLOSE button to open the disc tray.
2. Place a disc gently into the tray with the disc's label facing up.
3. Press
the OPEN/CLOSE button to close the disc tray,
the disc will be played automatically.
• If there are more than one CD or an MP3/WMA-CD
inserted, replays are then processed in order.
• For MP3/WMA-CD audio, it may take several minutes
to complete scanning the disc tracks.
• If you play a file with an English name or a MP3/WMACD medium in an English title, the song title will be
shown in the display. (Other languages besides English
may not be indicated.)
• An English-titled track containing a special character
will not show the title in the display.
<CD/MP3/WMA-CD PlaybackDisplay>
Track Indicator
Playtime Indicator
4. A
djust the volume according to needs with the
following procedures.
• Tuning the VOLUME knob.
• Press the Vol + or – button of the remote control.
The volume level can be adjust in 31 steps(VOLUME
MIN, VOLUME01- VOLUME 29, and VOLUME MAX).
5. Main Unit
To pause playback temporarily, press the p button.
Press p again to continue playing the disc.
Remote control
To pause playback temporarily, press the PAUSE(#)
button.
Press PLAY(+) button to continue playing the disc.
6. To end playing, press the STOP (@) button.
• If there is not one CD inserted in the disc tray, it is indicated
as “NO DISC”.
• The quality of MP3/WMA-CD playback may vary depending
on the condition of the disc containing the music files or the
condition of the recorder with which the disc was created.
• If different types of files or unnecessary folders are on the
same disc, you will have problems with playback.
English
8
9
Selecting a CD in the Disc changer
1. To select a specific disc, press the DISC SKIP
button on the remote control, until the required disc
indicator flashes.
Result: Each disc is selected.
or
• P
ress the DISC 1, DISC 2 or DISC 3 button on the
main unit to select a specific disc while the disc tray is
closed.
• If the selected disc is not loaded, the next disc is played
automatically.
Selecting a Track
You can select a desired track while the disc is
being played.
To play the previous track
Press the [ button within 3 seconds after the current
track started playing.
Press the [ button twice at least 3 seconds after the
current track started playing.
To play the next track
Press the ] button.
To play the current track
Press the [ button 3 seconds later after the current
track started playing.
To play the track of your choice
Press the [ or ] button to move to a desired track.
• You can also use the Number(0~9) button on the
remote control to select a track.
Searching for a Specific Music
Passage on a CD
When listening to a compact disc, you can quickly search for a specific music passage on a track.
To search for...
Press ...
Forwards..................................... )
Backwards................................... (
You can also press and hold the [, ] button on
the main unit to automatically scan for a track.
Repeat One or All Tracks on the
Compact Discs
You can repeat playing CD unlimitedly:
• CD containing a specific track.
• Whole tracks of a selected CD.
1. P
ress the REPEAT button.
Each time you press the REPEAT button, the
repeat mode will change as following:
MP3: OFF➝ TRACK ➝ DIRECTORY ➝ ALL ➝
RANDOM ➝ ALL DISCS
CD: OFF➝ TRACK ➝ ALL ➝ RANDOM ➝ ALL
DISCS
2. When you wish to stop the Repeat function,
press the REPEAT button until "OFF" is
displayed.
• OFF: Cancels Repeat Playback.
• TRACK: Repeatedly plays the selected track.
Searching a Track/Folder Quickly
You can select a track/folder directly without
the [, ] button.
CDDA
1. T
urn the EASY SEARCHING JOG control left or
right on the main unit to select a desired track.
2. Press the ENTER button on the main unit.
• You can move to the selected track directly.
MP3/WMA CD
1. Turn the EASY SEARCHING JOG control left or
right on the main unit to move to the previous/next
folder.
• Y
our Product will take a few seconds to search the
previous/next folder.
• “SEARCHING” is displayed.
2. When the searching is done, you will see the
previous/next folder name.
The track will start playing.
10
English
• DIRECTORY: Repeatedly plays all tracks in the
selected folder.
• ALL: Repeatedly plays the entire disc.
• RANDOM: Plays tracks in random order.
• ALL DISCS: Repeatedly plays the all discs.
A-B Repeat Playback
You can repeatedly play back a designated section
of a CD.
1. Press the REPEAT A-B button at the beginning
of desired part.
• 'RPT A' will be displayed.
2. Press the REPEAT A-B button at the ending of
desired part.
• 'RPT AB' will be displayed.
3. To cancel REPEAT A-B function, press the
REPEAT A-B button again.
• 'OFF' will be displayed.
REPEAT A-B function is available within a track.
➣➣
10 Skip Function
Press the +10 or -10 button while in playback mode.
This will skip the tracks as many as 10 or -10 from
the current track.
CD Programming
This function is not available during playback of an
MP3/WMA-CD.
• You can program the playback order of up to 24
tracks of your choice.
• However, you must stop playing the CD before
selecting tracks.
1. W
hile in CD playback mode, press the STOP(@)
button to stop playing the CD.
2. Press the ENTER (
message below:
) button to display the
(01= program number, --= track number)
3. Use the [ or ] button to move to a desired
track.
• Press [ to move to the previous track.
• Press ] to move to the next track.
4. Press the ENTER (
) button to confirm your
selection, the selection is stored and
is displayed.
5. To select a different track, following the steps 3 to 4 above.
6. Press the PLAY (+) button to play the
programmed tracks.
7. Press the STOP(@) button to stop playing the
programmed tracks, Press the STOP (@) button
again to cancel playing the programmed tracks.
• If you open the disc tray or turn off the
product, your programming will be canceled.
Checking or Editing the
Programmed Tracks
You can check a list of programmed tracks and
edit them as you want.
1. If a programmed track is being played, press the
STOP (@) button once.
2. Press the ENTER (
the message below:
) button twice to display
(C=Check, 01= program number)
3. Repeat pressing the ENTER (
the desired track is displayed.
) button until
4. Press the [ or ] button to select a different
track.
5. Press the ENTER (
selection.
) button to confirm your
6. To play the programmed tracks, press the
PLAY (+) button.
Auto Change Function
You can circularly play between the disc and the
USB.
1. Press the AUTO CHANGE button on the main unit.
Each time press this button, the mode will switch as
following:
AUTO CHANGE OFF ; AUTO CHANGE ON
• When the auto change mode is "ON", the music will be
played on DISC1➝DISC2➝DISC3➝USB1➝USB2
continuously.
• When the auto change mode is "ON", if you press
the POWER button, function change button or the
OPEN/CLOSE button, the auto change function
automatically switches to "OFF" mode.
• When USB is playing, if you disconnected the USB,
the auto change function automatically switches to
"OFF" mode.
• When the auto change mode is "ON", the recording
can't work.
• When the auto change mode is "ON", the REPEAT,
SLEEP function can't work and automatically changes
to OFF.
• When the auto change mode is "ON", the REC
SPEED, USB 2 REC, REPEAT, PROGRAM, DELETE
and SLEEP function can't work.
• If there's no DISC or no USB, it will jump to next
DISC or USB. (For example, the DISC1 plays end, if
the DISC 2/3 has no disc, it will jump to play USB1
music.)
English
10
11
Playing USB
Connect an external storage device such as USB
flash memory or external HDD (Hard Disk Drive)
to the product. You can play files in MP3/WMA
format.
Before you begin! • Connect the external USB storage device to your product.
• Select the USB mode by pressing the USB 1 or USB 2
button on the main unit or select the USB 1 or USB 2 by
pressing the FUNCTION button on the remote control.
• The first track of the first directory plays automatically, and
the play order is as below:
If you select USB1, USB1 ➝ STOP.
If you select USB2, USB2 ➝ STOP.
➣➣To stop playing
Press the STOP ( @ ) button to stop playing.
➣➣To remove the USB device
To Use High Speed Search
You can search the desired section quickly during
the play.
the (,) button.
➣➣•Press
Each time you press the button, you will move
forward/backward fast.
☛☛The sound will not output in fast playback mode.
To delete a file
You can delete a file on your USB device.
1. Play a file you want to delete.
2. Press the DELETE button.
3. Turn the EASY SEARCHING JOG control left or right on
the main unit or press the [,] buttons on the remote
control to select YES.
• To cancel the selection, press the RETURN button on
the main unit.
If you press the STOP ( @ ) button once
again, you can remove the USB device safely.
4. Press the ENTER button on the remote control.
The selected file will be deleted.
damaged.
To skip next 10 tracks
1. Press the +10 or -10 button while in playback
mode.
☛☛Do not connect a USB recharger to the USB port ☛☛The NTFS file system is not supported.
of this product. Otherwise, the product may be
To Select a Track from USB Device
You can select an MP3 file during the play.
f you want to move the next/previous(track), press the
➣➣I[,]
buttons shortly.
• It moves the next/previous file within the directory.
• If you press the [,] buttons more times than the
number of the files in the directory, it will move over to
the next directory.
To Search a Folder Quickly
1. Turn the EASY SEARCHING JOG control left or right
on the main unit or press the TUNING/ALBUM
button on the remote control to move to the previous/
next folder.
2. When the searching is done, you will see the previous/
next folder name. The track will start playing.
To repeat
1. P
ress the REPEAT button.
Each time you press the REPEAT button, the repeat
mode will change as following:
OFF➝ TRACK ➝ DIRECTORY ➝ ALL ➝ RANDOM
2. When you wish to stop the Repeat function, press the
REPEAT button until "OFF" is displayed.
• OFF: Cancels Repeat Playback.
• TRACK: Repeatedly plays the selected track.
• DIRECTORY: Repeatedly plays all tracks in the
selected folder.
• ALL: Repeatedly plays all tracks.
• RANDOM: Plays tracks in random order.
12
English
This will skip the tracks as many as 10 or -10 from the
current track.
Read through the instructions below before using
the USB storage
• Some USB devices may not work properly with this
product.
• This product supports only an external HDD that is
formatted in FAT file system.
• USB 2.0 HDD should be connected to a separate power
source. Otherwise, the USB 2.0 HDD will not work at all.
• If an USB external storage is connected to multiple
devices, only the MP3 files in the first HDD will be played.
• DRM-applied files are not supported. Digital Right
Management:This will restrict unauthorized access to a
DRM file so that the copyright of the file is protected from
piracy.
• Even if the extension of the file is .mp3, the file cannot be
played if it is formatted in MPEG layer1 or 2.
• Do not use an unrecognized USB hub.
• Only the first 15 characters of a MP3/WMA file are
displayed.
• Only removable HDDs with less than 160GB are
supported. Depending on the device, a 160GB- or more
removable HDD may not be supported.
• It will take several minutes to recognize the files in the
selected USB device.
• The USB device (USB HDD, in particular) may cause a
delay to move to the next track.
• The USB storage supporting only USB VER1.1 may perform
a slow access or may not recognize the file properties.
Listening a Radio
Selecting a Stored Station
You can store up to:
15 FM stations, 15 AM stations (optional).
1. Select FM or AM by pressing the TUNER/AUX
button on the main unit.
You can select FM or AM by pressing the
FUNCTION button on the remote control.
2. To search for a station
Press TUNING MODE button
Preset.................... Once or more times until PRESET
is displayed.
You can search the stored frequencies in the Preset mode.
Manually ............... Once or more times until MANUAL
is displayed.
You can search the frequencies one
by one in the Manual mode.
3. Select the station to be stored by:
• Pressing the TUNING/ALBUM , or . button
on the remote control button to select the preset
station.
or
Turn the EASY SEARCHING JOG control left or
right to search the station.
• Press and hold the TUNING/ALBUM , or .
button on the remote control to automatically
search for active broadcasting stations.
4. Press the MO/ST button to switch between stereo
and mono.
• In a poor reception area, select MONO for a clear, interference-free broadcast.
• This applies only when listening to an FM station. 5. If you do not want to store the radio station found,
revert to Step 3 and search for another station.
Otherwise:
a. Press the ENTER button.
b. Or, press the TUNING/ALBUM button on the
remote control to select a program number.
c. Press the ENTER button to save the preset.
6. To store any other radio frequencies required,
repeat Steps 3 to 4.
mode
➣➣In• ITuner
n the Manual mode, you can use [ or ] button
You can listen to a stored radio station as following:
1. Select FM or AM by pressing the TUNER/AUX
button on the main unit.
You can select FM or AM by pressing the FUNCTION button on the remote control.
2. Press the TUNING MODE button on the remote
control until “PRESET” is displayed.
3. P
ress [,] button on the main unit or TUNING/
ALBUM , , . on the remote control to select a
desired preset number.
or
Turn the EASY SEARCHING JOG control left or
right on the main unit to select the stored station.
Setting the Clock
For each step, you have a few seconds to set the
required options. If you exceed this time, you must
start again.
1. Switch the system on by pressing the POWER
(
) button.
2. Press the TIMER SET button and then press the
ENTER (
) button, "CLOCK" is displayed.
3. Press the ENTER (
) button, the hour flashes.
• Increase the hours: ,
• Decrease the hours: .
4. When the correct hour is displayed, press the
ENTER (
) button, the minutes flashes.
• Increase the minutes: ,
• Decrease the minutes: .
5. When the correct minute is displayed, press the
ENTER (
) button, " TIMER" appears in the
display.
• The current time is now set.
• You can display the time, even when you are using
another function, by pressing the TIMER SET button
once.
• You can also use ] or [ on the front panel instead
of TUNING/ALBUM , or . button in step 3,4.
on the main unit to manual search a radio station.
• In the Preset mode, you can use [ or ] button
or the EASY SEARCHING JOG control on the
main unit to search a stored radio station.
English
12
13
Timer Function
The timer enables you to switch the system on or
off at specific times automatically.
• Before setting the timer, check that the current time
is correct.
• For each step, you have a few seconds to set the
required options. If you exceed this time, you must
start again.
• If you no longer want the system to be switched on
or off automatically, you must cancel the timer by
pressing the TIMER ON/OFF button.
Example: You wish to wake up to music every morning.
1. Switch the system on by pressing the POWER (
button.
2. Press the TIMER SET button until
displayed.
)
3. P
ress the ENTER (
) button.
Result: ON TIME is displayed for a few seconds, you
can set the timer switch-on time.
5. Set the timer switch-off time.
a Press the TUNING/ALBUM , or . button to set the hours.
b Press the ENTER (
) button.
Result: The minutes flash.
c Press the TUNING/ALBUM , or . button to set the minutes.
d Press the ENTER (
) button.
Result: V
OLUME XX is displayed, where XX corresponds to the volume already set.
CD/MP3 (compact disc) . ..... Load one or more compact discs.
USB1/USB2.............. Connect the USB device.
14
English
2)If you select the RECORD Y, you can set the tuner
timing recording.
) button.
b.Press the ENTER (
Result: OFF TIME is displayed for a few
seconds, you can set the tuner timing recording
switch-off time.
4. Set the timer switch-on time.
a Press the TUNING/ALBUM , or . button to set the hours.
b Press the ENTER (
) button.
Result: The minutes flash.
c Press the TUNING/ALBUM , or . button to set the minutes.
d Press the ENTER (
) button.
Result: O
FF TIME is displayed for a few seconds, you can now set the timer switchoff time.
FM/AM (radio) .......... a
Press the ENTER (
) button
b Select a preset station by
pressing the TUNING/
ALBUM , or . button.
9. Press the ENTER (
) button.
Result: RECORD N is displayed, you can press the
TUNING/ALBUM , or . button to select the
RECORD Y or RECORD N, and then press ENTER
button.
1)If you select the RECORD N, it will cancel tuner
timing recording even if you have already set the
tuner timing recording.
) button.
a.Press the ENTER (
Result: ON TIME is displayed for a few seconds,
you can set the tuner timing recording switch-on
time.
TIMER is
6. P
ress the TUNING/ALBUM , or . button to
adjust the volume level and press the ENTER (
button.
Result: The source to be selected is displayed.
7. Press the TUNING/ALBUM , or . button to
select the desired source to be played when the
system switches on.
If you select...
You must also...
8. Press the ENTER (
) button.
Result: C
HECK REC (Do you want to record?) is displayed.
)
• The maximal tuner timing recording time is 5 hours.
• If the timer switch on and off times are identical, the
word ERROR is displayed.
• You may use ], [ buttons on the main unit to
instead of the TUNING/ALBUM , or . button to
adjust in step 4 to 9.
• If the switch-on or -off time is the same as the timing
recording time, only the switch-on or -off time is
effective, and the timing recording time is not applied.
• If the auto timer is turned on,the MP3/CD or USB
function may require an additional step to be
activated depending on the disc(or device).So it is
better for you to select the tuner function instead.
Cancelling the Timer
After having set the timer, it will start automatically as
shown by the TIMER indication on the display. If you
no longer wish to use the timer, you must cancel it.
To...
Press the TIMER ON/OFF button....
Cancel the timer . ........Once.
Result:
played.
Restart the timer .........Twice.
Result:
is no longer dis-
is displayed again.
• When you select the TIMER OFF mode, the TIMER
RECORDING and TIME function are not available. Recording Function
You can record sound of the CD, the Radio Broadcasting or sound from the external source into the
USB storage device.
1. C
onnect the external USB storage device you want
to record to the USB 2 (
) on your
product.
2. Play a Disc, adjust the Radio frequency or connect
the external source to your product.
CD
• Press the MP3/CD on the main unit to select the CD
function.
• Press the OPEN/CLOSE button to open the disc tray.
• Insert a CD and press the OPEN/CLOSE button to
close the disc tray.
• Use the CD selection ( [ or ] ) buttons to select the
desired song.
Tuner
• Select TUNER by pressing the TUNER/AUX button
on the main unit.
• Adjust the Radio frequency you want to record.
External Source
• Connect an External Component/MP3 player to your
product.
• Press the TUNER/AUX button to select <AUX> input.
• Play a song from the external device.
USB 1
• Connect an USB to USB 1 jack of your product.
• Press the USB 1 button to select USB 1.
• Play a song from the USB 1.
3. P
ress the USB REC button on the remote control or the
USB 2 REC button on the main unit to start recording.
CD
• “TRACK RECORDING” is displayed and CD
recording starts.
• Press and hold the USB REC button on the remote
control or press and hold the USB 2 REC button on
the main unit to start recording the all tracks of Disc.
"FULL CD RECORDING" is displayed.
• If you play the MP3/WMA file, the file is copied into the
USB device totally. “CHECK FILE”“COPY XX”“COPY END” is displayed.
When the recording is done, “STOP” will be displayed.
• If there is the same file name, "FILE EXIST" is
displayed, and the function is canceled.
• Do not disconnect the USB or the AC Cord during the
recording as this may cause file damage.
• If you disconnected USB device during the recording,
the main unit will be power off and you may not delete
the recorded file, In this case, please connect the USB
device to the PC and backup the USB data on the PC
first and then format the USB device.
• When the USB memory is not enough, it will be displayed
“NOT ENOUGH MEMORY”.
• The recording works if the USB device or the HDD is
formatted in the FAT file system. (The NTFS file system is
not supported.)
• When you use CD high speed search function, the CD
recording can’t work.
• Sometimes, the recording time may be longer with some
USB devices.
• In the program mode, you can't use the CD recording
function.
• When the CD recording, the EQ and GIGA SOUND
functions can not work and automatically change to OFF.
• When the CD recording, the REPEAT function can not
work and automatically changes to OFF.
• If you use the MIC function during the CD recording, the
voice from the microphone will be recorded.
• You can not record the radio when searching or no
available frequencies in the Tuner mode.
• Note that setting the input level too loud when recording
music from an external device through the AUX and USB
channel may introduce noise into the recording. In that
case, lower the external device’s volume level.
Recording Speed
You can select the recording speed before recording.
Each time you press the CD REC SPEED button
on the remote control, the recording speed will
change as following:
RECORD SPD x 1;RECORD SPD x 4
• While the Tuner or External Source is recording, the
recording speed does not supported.
• When you select RECORD SPD x 4, the audio sound will
not be output.
• If you connected the Microphone, you just have one recording
speed mode: RECORD SPD x 1.
• During recording, if you disconnect the Microphone, the
recording will stop, even if you reconnect the Microphone, it
will still stop.
Tuner /External Source
• RECORDING is displayed.
4. T
o stop recording, press the STOP (@) button and
then automatically create and save as the MP3 file.
5. To remove the USB device safely, press the STOP (@) button once again. After the recording, a directory
named “RECORDING”(CD), “CD COPY”(MP3 CD),
“TUNER RECORDING” or “AUX RECORDING” will be
created in your device.
English
14
15
Selecting EQ Mode
Your mini-compact system supports the
predefined equalizer settings between high and
low frequencies to be in harmonious with the
current music genre.
1. Press the EQ button.
Each time you press this button, the sound mode will .
switch as following:
OFF;FLAT;RANCHERA;SAMBA;CUMBIA
;HABANERA;BOOMBA;REGGAE;PARTY
;POP;HIPHOP;ROCK;JAZZ;CLASSIC
;STADIUM EQ ;DYNAMIC.S;MP3 ENHANCER
; VIRTUAL SOUND;U1+0+0+0;U2+0+0+0
;U3+0+0+0
2. Set the BASS (left numeric), MIDDLE (middle
numeric), TREBLE (right numeric) level.
Press the ENTER button when you select the U1 + 0
+ 0 + 0/U2 + 0 + 0 + 0/U3 + 0 + 0 + 0
Result: The BASS level(left numeric) flash.
Press the TUNING/ALBUM , or . button to select
from -06 to 06.
Press the ENTER button.
Result: The MIDDLE level(middle numeric) flash.
Press the TUNING/ALBUM , or . button to select
from -06 to 06.
Press the ENTER button.
Result: The TREBLE level(right numeric) flash.
Press the TUNING/ALBUM , or . button to select
from -06 to 06.
Press the ENTER button.
Result: setting is completed.
• When CD Recording, the EQ function can't work and
the EQ automatically switches to "OFF" mode.
• If no buttons is pressed within 8 seconds, your settings
will automatically be cancelled and the previous settings
will be saved.
• The EQ mode may be different depending on your
region.
Selecting USER EQ Mode
You can directly select the user EQ mode by press
the USER EQ button.
1. Press
the USER EQ button on the main unit until
the required option is selected.
Each time you press this button, the sound mode will switch as following:
OFF ; U1 + 0 + 0 + 0;U2 + 0 + 0 + 0;U3 + 0 + 0 + 0
2. You can refer the above to set the BASS (left numeric),
MIDDLE (middle numeric), TREBLE (right numeric) level.
• When CD Recording, the USER EQ function can't work
and the USER EQ automatically switches to "OFF"
mode.
• If no buttons is pressed within 8 seconds, your settings
will automatically be cancelled and the previous settings
will be saved.
• The USER EQ mode may be different depending on
your region.
16
English
Using the Dynamic Spot Mode
You can directly select the Dynamic spot mode for
listening music.
1. Press the DYNAMIC SPOT button on the main unit.
Each time you press this button, the sound mode will
switch as following:
DYNAMIC.S ; OFF
• The DYNAMIC SPOT mode may be different depending
on your region.
Using the Stadium Mode
You can directly select the Stadium mode for
listening music.
1. Press the STADIUM button on the main unit.
Each time you press this button, the mode will switch .
as following:
STADIUM EQ ; OFF
• The STADIUM mode may be different depending on
your region.
Giga Sound function
Your mini-compact system is equipped with the
function of GIGA SOUND mode .
The function of GIGA SOUND mode amplifies bass
and improves high key or bass twice as much for
you to appreciate powerful real sound.
1. P
ress the GIGA SOUND BLAST button on the
main unit or the SOUND button on the remote
control. Each time press this button, the sound will
switch as following:
OFF ; GIGA SOUND ; ADAPTIVE
; EXPLOSION
2. To cancel this function, press the GIGA SOUND
BLAST button until the “OFF” is displayed.
• The GIGA SOUND mode may be different depending
on your region.
LED LIGHTING Function
You can switch the LED mode to your preference.
1. Each time you press the LED LIGHTING button on
the main unit, the LED display mode will change as
following:
OFF ; MODE 1 ; MODE2
• If you select the LED OFF, all of the LED Lightings will
turn off.
• If you select the MODE 1, the front LED will turn on and
the top LED LIGHTING will turn off.
• If you select the MODE 2, the front LED will turn on
and the top LED LIGHTING will turn on.
Party function
You can choose a desired party mode.
1. P
ress the PARTY button.
Each time press this button, the party mode will switch as following:
PARTY 1 ; PARTY 2 ; PARTY 3 ; DJ LIGHT
• On the PARTY 2 and DJ LIGHTING mode, the Top LED will run depend on the signal level.(MX-E870/E871 only)
• On the PARTY 1 and PARTY 3 mode, the Top LED will be on or off and does not run. (MX-E870/E871 only)
• When you select the DJ LIGHT mode, if you tune the EASY SEARCHING JOG control, the LED Light of the
Speaker will flash.
Troubleshooting
Refer to the chart below when this unit does not function properly. If the problem you are experiencing
is not listed below or if the instruction below does not help, turn off the unit, disconnect the power
cord, and contact the nearest authorized dealer or Samsung Electronics Service Center.
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Sound is not produced.
• No sound is heard during fast playback, slow playback.
• Are the speakers connected properly? Is the speaker setup correctly
customized?
• Is the disc severely damaged?
The remote control does not
work.
• Is the remote control being operated within its operation range of angle
and distance?
• Are the batteries drained?
• The product is not working.
• While “NO DISC” message appears on the display of the product, press
(Example: The power goes out or
and hold the STOP (@) button on the main unit for longer than
the front panel key doesn't work
5 seconds with no disc (reset function).
or a strange noise is heard.)
Using the RESET function will erase all stored settings.
• The product is not working
Do not use this unless necessary.
normally.
Can't receive radio broadcast.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an
area with good reception.
English
16
17
Specifications
General
FM Tuner
AM Tuner
(optional)
CD Disc
Weight (MX-E850/E851)
Weight (MX-E870/E871)
Dimensions
Operating Temperature Range
Operating Humidity Range
Signal/noise ratio
Usable sensitivity
Total harmonic distortion
Signal/noise ratio
Usable sensitivity
Total harmonic distortion
CD : 12 cm (COMPACT DISC)
6.5 Kg
6.63 Kg
294 (W) x 410 (H) x 433.5 (D) mm
+5°C~+35°C
10 % to 75 %
62 dB
10 dB
0.2 %
35 dB
60 dB
3%
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
MX-E850/E851- 900 Watts (MAX. THD)
Front speaker output
Subwoofer
300 W/CH (6 Ω/100 Hz)
300 W (6 Ω/100 Hz)
MX-E870/E871- 1600 Watts (MAX. THD)
Amplifier
Front speaker output
320 W/CH (6 Ω/100 Hz)
Rear speaker output
160 W/CH (12 Ω/100 Hz)
Subwoofer
320 W/CH (6 Ω/100 Hz)
Frequency range
20Hz~20KHz
S/N Ratio
80dB
Channel separation
60dB
Input sensitivity
(AUX)800mV
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
- For information on the power supply and power consumption, refer to the label attached to the product.
18
English
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
Area
Contact Center
WebSite
Area
Contact Center
WebSite
0-800-555-555
0-88-555-55-55
8-10-800-500-55-500
0-800-61440
English
18
Code No. AH68-02452B (Rev 0.0)
Download PDF