MM-G25
Micro Component Audio system
CD/MP3-CD/WMA-CD/CD-R/RW Playback
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/global/register
Safety Warnings
ENG
This symbol indicates “dangerous voltage” inside
the product that presents a risk of electric shock or personal injury.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE REAR COVER (or BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol indicates important instructions
accompanying the product.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a CLASS 1
CLASS 1 LASER PRODUCT
LASER product.
KLASSE 1 LASER PRODUKT
Use of controls, adjustments or performance of procedures LUOKAN 1 LASER LAITE
other than those specified herein may result in hazardous KLASS 1 LASER APPARAT
radiation exposure.
PRODUCTO LASER CLASE 1
CAUTION : INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
WARNING : To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
•T
his apparatus shall always be connected to a AC outlet with a protective grounding connection.
•T
o disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains
plug shall be readily operable.
CAUTION
•A
pparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
•T
he Mains plug is used as a disconnect device and shall stay readily operable at any time.
Wiring the Main Power Supply Plug (UK Only)
IMPORTANT NOTICE
The main lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and if it requires
replacing, a fuse approved to BS1362 of the same rating must be used.
Never use the plug with the fuse cover removed. If the cover is detachable and a replacement is required, it must be of the same colour as the fuse fitted in the plug.
Replacement covers are available from your dealer.
If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved
extension lead or consult your dealer for assistance.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a main socket as there is a risk
of shock hazard from the bared flexible cord.
Never attempt to insert bare wires directly into a main socket. A plug and fuse must be used at all times.
IMPORTANT
The wires in the main lead are coloured in accordance with the following code:– BLUE = NEUTRAL BROWN = LIVE
As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows:–
The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter L or coloured BROWN or RED.
WARNING : DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL WHICH IS MARKED WITH THE
LETTER E OR BY THE EARTH SYMBOL
, OR COLOURED GREEN OR GREEN AND YELLOW.
What’s included (Check for the supplied accessories below.)
FM Antenna
2
User's Manual
Remote Control
Thank you for buying this
SAMSUNG micro-compact system.
Please take time to read these instructions.
They will allow you to operate your
system with ease and take full advantage
of its features.
Contents
Safety Warnings. ................................................................................................................................................................................... 2
Installing Your Micro-Compact System
Front Panel View........................................................................................................................................................................................ 4
Top Panel View ......................................................................................................................................................................................... 4
Rear Panel View ....................................................................................................................................................................................... 5
Remote Control.......................................................................................................................................................................................... 5
Where to Install Your Micro-Compact System........................................................................................................................................... 6
Connecting your System to the Power Supply.......................................................................................................................................... 6
Inserting Remote Control Batteries............................................................................................................................................................ 6
Connecting the Loudspeakers................................................................................................................................................................... 6
Connecting to an External Source............................................................................................................................................................ 7
Connecting the FM Aerial........................................................................................................................................................................... 7
Demo/Dimmer function.............................................................................................................................................................................. 8
Setting the Clock....................................................................................................................................................................................... 8
CD/MP3/WMA-CD-Player
To play the CD/MP3/WMA-CD.................................................................................................................................................................. .9
Selecting a Track...................................................................................................................................................................................... .9
Searching for a Specific Music Passage on a CD.................................................................................................................................... .9
Function to skip through 10 track at a time ............................................................................................................................................. .10
Remain Function ...................................................................................................................................................................................... .10
Display Function . ..................................................................................................................................................................................... .10
Repeating One or All Tracks on the Compact Discs................................................................................................................................ .11
A-B Repeat Playback................................................................................................................................................................................ .11
Programming the Order of CD Playback.................................................................................................................................................. .11
Checking or Changing Programmed CD Tracks....................................................................................................................................... .12
Usb
Playing USB ..............................................................................................................................................................................................12
To use high speed search..........................................................................................................................................................................13
To repeat....................................................................................................................................................................................................13
Remain Function ...................................................................................................................................................................................... .13
To skip next 10 tracks................................................................................................................................................................................13
To repeat section.......................................................................................................................................................................................13
Selecting a Track from USB Device...........................................................................................................................................................13
Tuner
About RDS broadcasting ..........................................................................................................................................................................14
About RDS DISPLAY function ..................................................................................................................................................................14
PTY(Program Type) indication and PTY-SEARCH function . ...................................................................................................................15
Searching for and Storing the Radio Stations ..........................................................................................................................................16
Selecting a Stored Station..........................................................................................................................................................................17
Improving Radio Reception.......................................................................................................................................................................17
Other Functions
CD Ripping Function..................................................................................................................................................................................18
Timer Function...........................................................................................................................................................................................19
Cancelling the Timer..................................................................................................................................................................................19
Mute Function.............................................................................................................................................................................................20
Selecting EQ Mode...................................................................................................................................................................................20
Treble Level Function.................................................................................................................................................................................20
Bass Level Function...................................................................................................................................................................................20
Power Sound Function...............................................................................................................................................................................20
Power Bass Function.................................................................................................................................................................................20
Setting the System to Switch off Automatically..........................................................................................................................................21
Connecting Headphones............................................................................................................................................................................21
Recommendations for Use
Safety Precautions.....................................................................................................................................................................................22
Cleaning Your Micro-Compact System......................................................................................................................................................22
Precautions When Using Compact Discs..................................................................................................................................................22
Before Contacting the After-Sales Service................................................................................................................................................23
Technical Specifications.............................................................................................................................................................................24
Symbols
Press
Push
Important
Note
3
ENG
Front Panel View
ENG
5
1
2
1.
2.
3.
3
4
4.usb jack
5. volume CONTROL BUTTON
window display
Compact Disc Compartment
Headphone Jack
Top Panel View
POWER BUTTON
FUNCTION BUTTON
SEARCH FUNCTION BUTTON(DOWN)
TUNING MODE OR STOP BUTTON
PLAY/PAUSE BUTTON
6. SEARCH FUNCTION BUTTON(UP)
7. CD OPEN/CLOSE BUTTON
1.
2.
3.
4.
5.
1
4
2 3 4 5 6
7
Rear Panel View
ENG
1. AUX IN
2. FM Aerial Connector Terminal
3. Speaker Connector Terminals
4. Clamp-Wire
(Fasten the speaker wires.)
1
2
3
4
Remote Control
37
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
1. POWER
31. REMAIN
2. TUNER
32. DEMO
3. CD
33. SLEEP
4. TIMER/CLOCK
34. USB
5. TIMER ON/OFF
35. AUX
6. CD RIPPING
36. DIMMER
7. TUNING MODE
37. OPEN/CLOSE
8. MO/ST
9. DISPLAY
10. +10
11. Skip and Search
12. Fast-Rewind
13. STOP
14. POWER SOUND
15. VOLUME 16. TREB/BASS
17. REPEAT
18. TUNING
19. REPEAT A-B
20. P.BASS
21. MUTE
22.VOLUME +
23. TUNING
24. EQ
25. PLAY
26. Fast-Forwardy
27. PAUSE
28. RDS DISPLAY
29. RDS PTY
30. PROGRAM/SET
5
Where to Install Your Micro-Compact
System
Inserting Remote Control Batteries
ENG
To take full advantage of your new micro-compact system, follow
these installation instructions before connecting the unit.
Install the system on a flat, stable surface.
Never place this unit on carpeting.
Never place this unit in an outdoor area.
Maintain an open space of approximately 6 inches (15 cm) on the sides
and rear of the system, for ventilation purposes.
Make sure that you have enough room to open the compact disc
compartment easily.
Place the loudspeakers at a reasonable distance on either side of the
system to ensure good stereo sound.
Direct the loudspeakers towards the listening area.
For optimum performance, make sure that both speakers are placed at
an equal distance above the floor.
Insert or replace remote control batteries when you:
Purchase the micro-compact system
Find that the remote control is no longer operating correctly
hen replacing the batteries, use a new set of batteries and never
W
mix alkaline and manganese batteries.
1
Place your thumb on the position marked
on the battery
compartment cover (rear of the remote control) and pull the cover in
the direction of the arrow.
2
Insert two AAA, LR03 or equivalent batteries, taking care to respect
the polarities:
+ on the battery against + in the battery compartment
– on the battery against – in the battery compartment
3
Replace the cover by sliding it back until it clicks into position.
If you will not be using the remote control for a long time, remove the
batteries to prevent corrosion.
The remote control can be used up to approximately 7 meters in a straight line. It can also be operated at a horizontal angle of up
to 30° from the remote control sensor.
Connecting your System to the
Power Supply
Before plugging your system into a main socket, you must check the
voltage.
1
2
Plug the main lead into an appropriate socket.
Press the
system .
(STANDBY/ON) button to switch your micro-compact
Connecting the Loudspeakers
The loudspeaker connector terminals are located on the rear
of the system.
There are two terminals on the system:
left speaker (marked L)
right speaker (marked R)
To achieve the correct sound quality,insert those speaker
connector cables to the speaker connector terminals of the
system.
6
Connecting to an External Source
The auxiliary input can be used to take advantage of the
sound quality of your micro-compact system when listening to
other sources.
Examples: A television
A DVD player
A VCR
To connect to the external source, the source must have an audio
output. In addition, you need an connection cable.
1
2
Connecting the FM Aerial
ENG
How to connect a COAXIAL TYPE aerial.
Connect a 75Ω antenna to the FM antenna terminal.
Plug the connector on the FM aerial supplied into the coaxial socket (75Ω)
marked FM on the rear of the system.
Follow the instructions given on Page 16 to tune into a radio station, and
determine the best position for the aerial.
If reception is poor, you may need to install an outdoor aerial.
To do so, connect an outdoor FM aerial to the FM socket on the rear of the
system using a 75Ω coaxial cable (not supplied).
Set the system to standby mode and disconnect it and the external
source from the main socket.
Connect the audio cable to the rear of the micro component system.
Be sure to match connector colours.
3
4
5
6
Plug the system back into the main socket and press
POWER to switch it on.
Select the AUX source by pressing AUX.
Result: AUX is displayed.
Switch the external source on.
Adjust the volume and balance as required:
Volume
Equalizer
Example: You can watch a film and take advantage of stereo sound
provided that the original sound track is in stereo (as if you were
in a cinema).
2
3
4
7
DEMO/DIMMER function
Setting the Clock
ENG
All functions available on the system can be viewed on the
display and the display's brightness can be switched between
"on" and "off".
1
Press the DEMO button.
Result: All functions available on the system appear on the front
panel display.
ach of these are explained in detail in this guide. Please refer to the
E
relevant section.
2
Press the DIMMER button.
Result: The Dimmer function is selected and the display darkens.
3
Press the DIMMER button once again to brighten the front panel
display.
A display brightness control can only be performed while the system
power is on.
Your system is equipped with a clock which allows you to turn
your system on and off automatically.
You should set the clock:
When you first purchase the micro-compact system
After a power failure
After unplugging the unit
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
1
2
3
4
Press TIMER/CLOCK twice.
Result: CLOCK is displayed.
Press PROGRAM/SET.
Result: The hour flashes.
To...
Press the TUNING button
Increase the hours
Decrease the hours
5
6
7
1
Switch the system on by pressing STANDBY/ON.
When the correct hour is displayed, press PROGRAM/SET.
Result: The minutes flash.
To...
Press the TUNING button
Increase the minutes
Decrease the minutes
When the correct time is displayed, press PROGRAM/SET.
Result: The clock starts and is displayed.
You can display the time, even when you are using another
function, by pressing TIMER/CLOCK once.
You can also use
,
buttons on the main unit to instead of
TUNING button
or
in step 4, 6.
2,3
2
3,5,7
4,6
4,6
4,6
1
8
4,6
.
To play the CD/MP3/WMA-CD
Selecting a Track
ENG
You can play 12 cm or 8 cm compact disc without an adapter.
1
2
3
4
5
6
7
You can select the track you wish to listen to when a disc is
playing.
You can play 12 cm or 8 cm compact discs without an adapter.This
unit has been designed to playback the CDs: Audio CD, CD-R,
CD-RW and MP3/WMA,-CD.
Continued use of irregular shape CDs (heart-shape, octagonal, etc.)
can damage the unit.
To play the previous track
within 3 seconds after the current track started
Press the
playing.
twice 3 seconds after the current track started playing.
Press the
Select the CD function by pressing PLAY/PAUSE(
To play the next track
Press the
.
) button.
Press the Open/Close( ) button.
Result: The compartment opens.
Place your disc in the compartment, with the label on the disc
facingupwards.
Close the compartment by pressing the Open/Close(
again.
) button
Press the PLAY/PAUSE(
) button.
Your CD Player will take a few moments to scan through all
the tracks recorded on a particular MP3/WMA-CD.
The English name of the song may be indicated on the display
only if directly downloaded from the PC or if the purchased MP3/
WMA-CD is sorted according to titles(directory).
(Other languages besides English may not be indicated.)
The English name of the track may not be indicated depending
on the characteristics of the MP3/WMA-CD.
To play the current track
3 seconds after the current track started playing.
Press the
To play the track of your choice
Press the
or
the appropriate number of times.
◆◆You can also use the
select a track.
or
buttons on the remote control to
Adjust the volume according to needs with the following procedures.
Press the VOLUME button of the main unit.
or
Press the VOLUME+or –button of the remote control. The volume
level can be adjust in(VOL MIN,VOL 1- VOL 29,andVOL MAX).
Main set
To pause playback temporarily, press the PLAY/PAUSE(
) button.
Press PLAY/PAUSE(
) again to continue playing the disc.
Remote control
To pause playback temporarily, press the PAUSE( ) button.
Press PLAY( ) button to continue playing the disc.
8
Press the STOP(
) button when you have finished.
Press and hold OPEN/CLOSE( ) button for 5 seconds, ”LOCK”will
be displayed and the compartment doesn’t open.In this way you
must press and hold OPEN/CLOSE( ) button for along time until
“UNLOCK” will be displayed, the compartmentcan open.
2,4
8
1,5,7
6
Searching for a Specific Music
Passage on a CD
When listening to a compact disc, you can quickly search for a
specific music passage on a track.
To search through the tracks...
Press ...
Forwards
Backwards
You can also press and hold down
search through the tracks.
,
on the main unit to auto
7
7
6
6
9
Function to skip through 10
tracks at a time
What is WMA?
ENG
WMA means Windows Media Audio, the global standard for audio
signal compression technology.
What is MP3?
MP3 means MPEG1 Layer 3, the global standard for audio
signal compression technology. It uses digital compression
technology to compress original sound data by up to 12 times
without sound quality degradation.
Press the +10 button briefly while playing back a
CD and MP3/WMA-CD . The track 10 tracks after the
current one will then be played back.
Example: If you want to select track 43 during playback of track 5,
press the +10 button four times, and then press the
button three times .
5 10 20  30  40  41  42  43
File Compatibility
he unit will playback files created in MP3 format (Mpeg1.
T
Layer3) with *.mp3 as their extension,and some WMA files
with.WMA extension can’t be playback.
Playback will be impossible for the file of MP2 or 22KHz.
How many MP3 files can a CD-R or CD-RW disc record?
The maximum capacity of one CD-R or CD-RW disc is
680MB.
Normally, one MP3 file has a capacity of 4MB, therefore
approximately 170 files can be recorded on a single disc.
Remain Function
You can check the remaining time.
1
◆◆If you press the REMAIN button, the remaining time is
displayed.
Regarding the playback of CD-R/RW
In the case of an original CD-R(Recordable) recorded in
audio CD format, CD-RW(Rewritable) and editing by the
user, playback is processed on the respective
completed status. (The player may not be played back
according to the characteristics of the CD or recorded
status.)
The CD-RW is comparably less reflexive than CD which
causes more time delay to read.
Press the REMAIN button .
2
To cancel this function, press the REMAIN button again.
Display Function
(This function is not available during playback of an MP3/WMA-CD.)
You may check the total tracks of the disc.
1
10
Press the DISPLAY button.
Result:The total tracks numuber of the disc is displayed, and it will
disappear after 3 seconds.
Repeating One or All Tracks
on the Compact Discs
You can repeat indefinitely:
A specific track on a compact disc.
All tracks on the compact disc selected.
1
2
Press REPEAT button.
Each time you press the REPEAT button, the repeat mode will
change as follows:
MP3: RPT TRK ➝ RPT DIR ➝ RPT DISC ➝ RPT SHF ➝ RPT OFF.
CD: RPT TRK ➝ RPT DISC ➝ RPT SHF ➝ RPT OFF.
Programming the Order of CD Playback
(This function is not available during playback of an MP3/WMA-CD.)
The order of the track desired to listen
The track not desired to listen
You can program up to 24 tracks.
You must stop the compact disc player before selecting the tracks.
1
2
When you wish to stop the Repeat function, press Repeat until
RPT OFF is displayed.
◆◆RPT DISC: Repeatedly plays the entire disc.
.
Press PROGRAM/SET.
Result: The following indications are displayed:
(01 = Program no., -- -- = Track no. on the disc)
3
◆◆RPT SHF: Plays tracks in random order.(Each track can be played
one time.)
◆◆RPT OFF: Cancels Repeat Playback.
If the CD function is selected, stop the player by pressing
◆◆RPT TRK: Repeatedly plays the selected track.
◆◆RPT DIR: Repeatedly plays all tracks in the selected folder.
ENG
You can decide:
4
Select the required track by pressing the
or
button:
Press the
button to move back through the tracks.
Press the
button to move forward through the tracks.
Press PROGRAM/SET to confirm your selection.
Result: The selection is stored and
5
6
7
is displayed.
To select other tracks, repeat Steps 3 to 4.
Press PLAY (
programmed.
) to listen to the track selection in the order
button one time , compact disc player is stopped, and
When press
press
button again to cancel the selection.
◆◆If you open the compartment or turn off the power,
the selection is cancelled.
1,2
A-B Repeat Playback
You can repeatedly play back a designated section of a CD/MP3/WMA-CD.
1
2
3
Press the REPEAT A-B button at the beginning of desired part.
'RPT A-' shows.
2,4
Press the REPEAT A-B button at the ending of desired part.
'RPT A-B' shows.
To cancel REPEAT A-B function, press REPEAT A-B button again.
Point B cannot be set until 5 seconds of playback has
elapsed from point A.
3
3
1, 7
6
11
Checking or Changing Programmed
CD Tracks
ENG
You can check or change your selection of tracks at any time.
1
2
Press
once if you have started listening to the selection.
/
/
Press PROGRAM/SET.
Result: The following indications are displayed:
(CH = Check, 01=Program No., -- -- = Track No. on the disc)
If you have already programmed 24 tracks, CH is displayed
instead of PR when you press PROGRAM/SET.
3
4
5
6
Press PROGRAM/SET once or more times until the track to be changed is
displayed.
Press
or
button to select a different track.
Press PROGRAM/SET to confirm your change.
Press PLAY ( ) to start listening to the selection.
Result: The first track selected is played.
Please be aware of the following before using USB.
ome external USB storage devices may not be compatible with this
S
player.
With external HDD, FAT format can be played, however,the
NTFS format can not.
With USB 2.0 HDD, connect to a separate power source.
If it’s not connected to a separate power source, it may not work.
If memory of an external USB storage device is segmented into
several parts, MP3 files of only the first hard disk drive can be
played.
DRM applied files are not played.
Digital Rights Management: Technology and service that protect the
profit and rights of copyright owners by disallowing unauthorised use of
digital contents.
Even if the file name ends with .mp3, the file does not play if actual file
format is MPEG layer 1 or 2.
Do not use a USB hub as it will not be recognized.
Up to 15 letters of MP3/WMA file name will be shown.
Delay
hen selecting USB function,file reading (READ-IN) may take several
W
minutes.
When playing a USB device,there may be a delay then advancing to the
next track,especially with HDD.
The operation time of external USB storage devices will vary;even when
they are of the same capacity.
If the external USB storage device supports only USB VER1.1
and the access speed is slow,the file may not property.
2,3,5
4
1
6
4
1
Playing USB
You can play MP3/WMA files by connecting to various external USB
storage devices such as USB flash memory or HDD(Hard Disc drives).
1
2
Connect the external USB storage device to your player.
Select USB function by pressing the USB button.
The first track of the first directory plays automatically.
To stop playing
Press the Stop (
) button to stop playing.
o not connect a USB charging device to the USB connection port
D
on the player, because it may cause damage to the product.
12
2
To use high speed search
To skip next 10 tracks
ENG
Before you begin! Connect the external USB storage device to your player.
Select USB function by using the USB button.
Before you begin! Connect the external USB storage device to your player.
Select USB function by using the USB button.
You can search the desired section quickly during the play
Press the
,
button.
Whenever you press the button, you can search backward or
forward quickly.
When you use the high speed search function, there is no sound.
To repeat
Before you begin! Connect the external USB storage device to your player.
Select USB function by using the USB button.
Press the +10 button on the remote control shortly during the play.
Example: If you want to select 43rd track while 15th track is
playing, press the +10 button 3 times, and then press
button 3 times .
the
15  20  30  40  41  42  43
To repeat section
Before you begin! Connect the external USB storage device to your player.
Select USB function by using the USB button.
Press the REPEAT A-B button at the beginning of desired part.
'RPT A-' shows.
1
Press REPEAT button.
Each time you press the REPEAT button, the repeat mode will
change as follows:
RPT TRK ➝ RPT DIR ➝ RPT ALL ➝ RPT SHF ➝ RPT OFF.
When you wish to stop the Repeat function, press Repeat until RPT
OFF is displayed.
◆◆RPT TRK: Repeatedly plays the selected track.
◆◆RPT DIR: Repeatedly plays all tracks in the selected folder.
◆◆RPT ALL: Repeatedly plays all tracks.
◆◆RPT SHF: Plays tracks in random order. (Each track can be played one time.)
◆◆RPT OFF: Cancels Repeat Playback.
2
3
Press the REPEAT A-B button at the ending of desired part.
'RPT A-B' shows.
To cancel REPEAT A-B function, press REPEAT A-B button again.
Point B cannot be set until 5 seconds of playback has
elapsed from point A.
Selecting a Track from USB Device
You can select an MP3 file during the play.
Remain Function
Before you begin! Connect the external USB storage device to your player.
Select the USB function by using the USB button.
You can check the remaining time.
Before you begin! Connect the external USB storage device to your player.
Select USB function by using the USB button.
1
Press the REMAIN button .
◆◆If you press the REMAIN button, the remaining time is
displayed.
2
If you want to move the next/previous(track), press the
,
button shortly.
It moves the next/previous file within the directory.
If you press the
,
button more times than the number of
the files in the directory, it will move over to the next directory.
To cancel this function, press the REMAIN button again.
13
About RDS DISPLAY function
About RDS broadcasting
ENG
This unit has the RDS (Radio Data System) function, which enables for
the various information such as broadcasting station, radio text, time
and 30 types of programs (News, Rock, Classic, etc.) to be received
from the FM RDS station together with normal radio signal.
1
2
3
Press the (
) button.
Receive the FM radio.
See the radio receiving method on the page 16.
FM and frequency are shown on the display
About "PS NAME" MODE
Displays the name of broadcasting station.
Press the RDS DISPLAY button to select the PS NAME.
"PS NAME" appears on the display.
If the PS information is being received, the PS name (BBC, AFO, NDR,
etc.) is shown on the display.
If the PS information isn't received, the original FM frequency is shown.
Press the RDS DISPLAY button to select the desired RDS mode.
Whenever the button is pressed, RDS mode changes as follows.
PS NAME
RT
CT ven though no RDS DISPLAY button is pressed, the reception of
E
PS information ensues the PS name is displayed.
Current FM frequency
The RDS function is available only in FM broadcasting.
About 'RT' MODE
RDS may not operate correctly if the station tuned is not
transmitting RDS signal property or if the signal strength is weak.
Description on RDS function
1. PTY(Program Type) : Displays the type of programme
currently being broadcast .
2. PS NAME(Program Service Name) : Indicates the name of
broadcasting station and is composed of 8 characters.
3. RT(Radio Text) : Decodes the text broadcast by a station (if
any) and is composed of maximum 64 characters.
Displays the character transmitted from the broadcasting station.
Press the RDS DISPLAY button to select the RT MODE.
"RT" appears on the display.
If the RT information is being received, the received information is
shown on the display.
If the RT information isn't received, the "NO RT" is shown on the
display.
4. CT(Clock Time) : Decodes the real time clock from the FM
frequency.
Some stations may not transmit PTY, RT or CT
information therefore this may not be displayed in all cases.
About CT(Clock Time)
Sets the time of RDS clock.
5. TA(Traffic Announcement) : When this symbol flashes it
shows that the traffic announcement is in progress.
To select the CT time, set the RDS DISPLAY button to CT MODE.
1
3
14
he CT information will take up to 2 minutes to be decoded
T
therefore the clock isn’t displayed immediately.
If there is no received CT information, "NO CT" is displayed.
PTY(Program Type) indication and
PTY-SEARCH function
ENG
 The PTY information is composed of an identification symbol, which helps
the FM radio to recognize the program type of each FM station.
 The below 30 PTY information is shown on the display by pressing the
RDS PTY button.
 To stop searching any time during the process, press TUNING MODE
while searching.
 There is a time limit in doing the followings steps.If the setting is cancelled
before you finish,start from step 1 again.
 When pressing the buttons on the primary remote control,make sure that
you have selected the FM station using the primary remote control.
Display
Program Type
NEWS
• News including an announced opinion and report
AFFAIRS
• Several matters including a current incident, documentary,
discussion and analysis.
INFO
• Information including weights and measures, returns and forecast,
matters interesting the customer, medical information, etc.
SPORT
• Sports
EDUCATE
• Education
DRAMA
• Drama-Radio serial, etc.
CULTURE
• Culture-National or local culture including the religious problem,
social science, language, theatre,etc.
SCIENCE
• Natural science and technology
VARIED
• Others-Speech, amusing program (quiz, game), interview,
comedy and satirical play, etc.
POP M
• Pop music
ROCK M
• Rock music
M.O.R.M
• M.O.R- Comfortable music, occasionally vocal or piece
LIGHT M
• Light classical music- Classical music and instrumental
and chorus music
CLASSICS
• Heavy classical music-Orchestra music, symphony, chamber
music and opera
OTHER M
• Other music - Jazz, R&B country music
WEATHER
• Weather
FINANCE
• Finance
CHILDREN
• Children’s programmes
SOCIAL
• Social affairs
RELIGION
• Religion
PHONE IN
• Travel
LEISURE
• Leisure
JAZZ
• Jazz Music
COUNTRY
• Country Music
NATION M
• National Music
Receive the FM radio.
See the radio receiving method on the page 16.
The FM and frequency appear on the display.
2
Press the RDS PTY button.
The PTY MODE(NEWS, AFFAIRS, etc.) appears on the display.
or
Press the TUNING
button to select the desired PTY
MODE.
If the station is transmitting no PTY information, 'NO PTY' lights
on the display.
When the PTY MODE is selected(The PTY MODE is shown on
the display), press the PTY KEY once again to convert into PTYSEARCH MODE and auto-search the station sequentially.
If the PTY MODE received in the course of auto-search agrees
with the selected PTY MODE, the auto-search stops and the PTYSEARCH is finished.
If the PTY MODE which agrees with the PTY MODE selected in
the course of auto-search, isn't received, it is returned to the first
frequency at beginning the PTY SEARCH and the auto-search and
PTY SEARCH are suspended.
2
2
2
• Oldies Music
FOLK M
• Folk Music
DOCUMENT
• Documentary
TEST
1
• Phone in
TRAVEL
OLDIES
About PTY-SEARCH
• Alarm Test
15
Searching for and Storing the Radio
Stations
ENG
You can store up to:
15 FM stations
1
2
3
Switch the system on by pressing STANDBY/ON.
Select the TUNER function by pressing TUNER.
o search for a
T
station...
4,7
4,7
3
Press Tuning Mode button
Once or more times until PRESET is displayed.
Once or more times until AUTO is displayed.
Preset
Automatically
Once or more times until MANUAL is displayed.
Manually
4
1
5
Select the station to be stored by:
Pressing TUNING
or
on the remote control.
To scroll through the frequencies faster when searching
manually, hold down the
or
buttons.
The automatic search procedure may stop on a frequency that
does not correspond to a radio station. If this happens, use the
manual search mode.
5
6
7
Adjust the volume by:
Press the Volume button on the main unit
or
Pressing the Volume + or – buttons on the remote control
Select the FM stereo or mono mode by pressing Mo/ST.
If you do not want to store the radio station found, revert to Step 3
and search for another station.
2
Otherwise:
a Press PROGRAM/SET.
b Press
or
or
on the main unit or press TUNING on the remote control to assign a program number .
c Press PROGRAM/SET to store the radio station.
8
To store any other radio frequencies required, repeat Steps 3 to 7.
6
3
In Tuner mode
manual tuning mode, you can use
In
,
button on the main unit to manual search a radio station.
During Tuner auto searching, press
button on the main unit or
TUNING MODE button on the remote control to stop auto
searching.
In Preset tuning mode, you can use
,
button on the main unit to search a stored radio station.
4,7
5
16
4,7
5
Selecting a Stored Station
You can listen to a stored radio station as follows:
1
2
3
4
Switch the system on by pressing STANDBY/ON.
Select the TUNER function by pressing TUNER.
Improving Radio Reception
You can improve the quality of radio reception by:
Rotating the FM aerial
Testing the positions of the FM aerials before fixing them permanently
If reception from a specific FM radio station is poor, press Mo/ST. to
switch from stereo mode to mono. The quality of the sound will be
improved.
Press the Tuning Mode button on the remote control or on the
main unit until “PRESET” is displayed.
Press
to select the desired station.
or
or
Select the desired station by pressing the
TUNING
or
button on the remote control.
Result: The desired station is now received.
1
3
4
4
2
3
4
4
17
ENG
CD RIPPING Function
ENG
You can rip a compact disc as a MP3 file on the USB
This feature enables you to ripping with the start of the disc or track
of your choice.
1
2
3
4
5
Switch the system on by pressing STANDBY/ON.
Connect the USB.
Load a compact disc(Digital Audio).
ress the OPEN/CLOSE button to open the CD door.
P
Insert a CD and press the OPEN/CLOSE button to close the CD
door.
Use the CD selection (
song.
or
) buttons to select the desired
1
3
Press CD RIPPING button on remote control to starting ripping.
If the system is playing state, press this button, “TRACK RIPPING”
is displayed and CD RIPPING starts.
If the system is playing state, press and hold this button, “FULL CD
RIPPING” is displayed and CD RIPPING starts.
During CD ripping, do not disconnect USB device.
To stop ripping, press STOP(
and save as the MP3 file.
)button and then automatically create
After CD-Ripping, a directory named “RIPPING” will be created in your
device, and the file name is same with the disc.
Note
◆◆Don’t disconnected USB and AC Cord during CD-Ripping. This may
cause the file damage. If you want to stop CD-Ripping during
CD-Ripping, you must press stop Key first and after the CD Stopped,
then you can remove the USB device.
◆◆If you disconnected USB device when CD Ripping, the main unit will be
power off and you may not delete the ripped file,In this case, please
connect the USB on the PC and backup the USB data on the PC first
and then formate the USB device.
◆◆When the USB memory is not enough, it will be displayed “RIPPING
ERROR”.
◆◆DTS-CD can’t for CD Ripping.
◆◆With external HDD, FAT format the USB can be CD Ripping, but not
NTFS. The CD Ripping function of this product does not support all USB
devices.
◆◆When you use CD high speed search function or in the Pause or Stop
mode, the CD Ripping can’t work.
◆◆During CD Ripping, do not deal impact.If is shocked while CD Ripping,
CD Ripping maybe disengage.
◆◆Sometimes, some of USB devices, CD Ripping time is long.
◆◆In program mode, you can't use CD RIPPING function.
18
4
5
3
3
Timer Function
ENG
The timer enables you to switch the system on or off at
specific times.
Example: You wish to wake up to music every morning.
If you no longer want the system to be switched on or off
automatically, you must cancel the timer.
Before setting the timer, check that the current time is correct.
For each step, you have a few seconds to set the required
options. If you exceed this time, you must start again.
4
5
6
7
NR
Switch the system on by pressing STANDBY/ON.
REC
1
2
3
Press Timer/Clock until
4,5,6,7
4,5,6,7
TIMER is displayed.
Press PROGRAM/SET.
Result: ON TIME is displayed for a few seconds, followed by any
switch-on time already set; you can set the timer switch-on time.
2
Set the timer switch-on time.
or
buttons.
a Press the TUNING
b Press PROGRAM/SET.
Result: The minutes flash.
or
buttons.
c Press the TUNING
d Press PROGRAM/SET.
Result: O
FF TIME is displayed for a few seconds, followed by any
switch-off time already set, you can now set the timer switch-off
time.
3,4,5,6,7,8
Set the timer switch-off time.
or
buttons.
a Press the TUNING
b Press PROGRAM/SET.
Result: The minutes flash.
or
buttons.
c Press the TUNING
d Press PROGRAM/SET.
Result: V
OL XX is displayed, where XX corresponds to the
volume already set.
4,5,6,7
or
to adjust the volume level and press
Press TUNING
PROGRAM/SET.
Result: The source to be selected is displayed.
4,5,6,7
or
buttons to select the source to be
ress the TUNING
P
played when the system switches on.
If you select...You must also...
8
1,9
TUNER (radio)
a P
ress PROGRAM/SET.
b Select a preset station by press
or the TUNING
buttons.
CD (compact disc)
Load disc.
USB
connect usb.
Cancelling the Timer
After having set the timer, it will start automatically as shown
REC no longer wish
by the TIMER indication on the display. If you
to use the timer, you must cancel it.
Press PROGRAM/SET to confirm the timer.
REC
To...
Press TimerNROn/Off...
Cancel the timer
Once.
Result:
NRlonger displayed.
is no
Restart the timer Twice.
Result:
is displayed again.
¡¡If the timer switch on and off times are identical, the word ERROR
is displayed.
,
buttons on the main unit to instead of the
¡¡You may use
or
buttons to adjust in step 4, 5, 6, 7.
TUNING
19
Mute Function
Bass Level Function
BASS function stresses low tones providing thudding
sound effects.
ENG
You can turn the sound off temporarily on your system.
Example: You wish to answer a telephone call.
1
2
1
Press Mute.
To switch the sound back on , press Mute again or the Volume
buttons.
2
Press TREB/BASS button until BASS 00 is displayed. Press
button to select from BASS -04 to BASS 04.
or
You can select the level of low tones you desire.
Power Sound Function
Selecting EQ Mode
Your micro-compact system is equipped with a preset equalizer
that allows you to choose the most appropriate balance
between treble and bass frequencies, according to the type of
music you are listening to.
1
1
Press EQ button until the required option is selected.
To obtain a...
Select...
Normal balance (linear)
Balance suitable for pop music
Balance suitable for rock music
Balance suitable for classic music
Balance suitable for jazz
Balance suitable for super bass
PASS
POP
ROCK
CLASSIC
JAZZ
S.BASS
PressTREB/BASS button until TREB 00 is displayed. Press
button to select from TREB -04 to TREB 04.
2
You can select the level of high tones you desire.
To cancel this function, press P.SOUND again, “OFF” is displayed
for a few seconds.
Your micro-compact system has a bass amplification function
called SBS (Super Bass Sound). This function makes the sound
more powerful and real.
Treble Control function stresses high tones providing thudding
soundeffects.
1
2
Press the P.SOUND button.
Result:“P.SOUND” is displayed.
Power Bass Function
Treble Level Function
20
Your compact system is equipped with the function of
PowerSound.
The function of Power Sound amplifies bass and improves
highkey or bass twice as much for you to appreciate
powerful realsound.
or
1
Press the P.BASS button.
Result: “P. BASS” is displayed.
2
To cancel this function, press P.BASS again, “OFF” is displayed for
a few seconds.
Setting the System to Switch off
Automatically
While listening to music, you can set the system to switch
off automatically.
Example: You wish to go to sleep to music.
1
2
Press Sleep.
Result: playback starts and the following indications are displayed:
90 MIN
You can connect a set of headphones to your micro-compact
system so that you can listen to music or radio programmers
without disturbing other people in the room. The headphones
must have a 3.5ø jack or an appropriate adapter.
Connect the headphones to the Phones jack on the main unit.
Result: The loudspeakers are no longer used to output the sound.
Prolonged use of headphones at a high volume may damage your
hearing.
Press Sleep once or more times to indicate how long the
system should continue playing before it switches off:
3
Connecting Headphones
At any time, you can:
Check the remaining time by pressing Sleep
Change the remaining time by repeating Steps 1 and 2
To cancel SLEEP function, press Sleep once or more times
until SLEEPOFF is display.
21
ENG
Cleaning Your Micro-Compact
System
Safety Precautions
ENG
The following diagrams illustrate the precautions to be taken
when using or moving your micro-compact system.
To obtain the best possible results from your micro-compact
system, you must clean the following elements regularly:
The outer casing
The compact disc player
The cassette players (heads, rollers and drive capstans)
lways unplug the system from the wall outlet:
A
Before cleaning it
If you are not going to be using it for a long time
Outer Casing
Clean the outer casing regularly using a soft cloth and a light detergent. Do
not use abrasive powders, liquids or aerosol cleaners. Never let any liquids
get into the system.
Ambient operating conditions:
Ambient temperature
5°C-35°C
Humidity
10-75%
Do not expose the unit to direct sun
radiation or other heat sources.
This could lead to overheating and
malfunction of the unit.
Compact Disc Player
1
2
Before playing a compact disc, clean it with a special CD cleaning
agent. Do not use the same cleaning agents as for vinyl LP records.
Carefully wipe the disc from the centre outward.
Regularly clean the player with a special cleaning disc (available from
your local dealer).
If you will not be using the remote control for a long time, remove
the batteries to prevent corrosion.
Although your system is very hard-wearing, it should not be used
in an excessively dusty environment or subjected to shocks or
extreme heat (close to heating appliances or in direct sunlight, etc.).
If the unit emits an unpleasant odor when in use, unplug it from
the main supply and contact the after-sales service.
Do not place potted plants or vases
on top of the unit. Moisture entering
the unit could lead to dangerous
electric shock and can cause
equipment damage. In such events
immediately disconnect the main
plug from the socket.
During thunderstorms, disconnect
the main plug from the socket.
Main voltage peaks due to lightning
could damage the unit.
Precautions When Using Compact
Discs
vOLUME
UP
DOwN
Remove the batteries from the
remote control, if not used for any
extended period.
Leaking batteries can cause serious
damage to the remote control.
When using headphones, take care
not to listen at excessive volumes.
Extended use of headphones at
high volumes will lead to hearing
damage.
Do not place heavy items on the
main lead. Main cable damage can
lead to damage of the equipment (fire
hazard) and can cause electric shock.
Do not remove any equipment panels.
The inside of the unit
contains live components, which
cause electric shock.
22
Handle your compact discs with care. Always hold them by the edges
to avoid leaving fingerprints on the shiny surface.
When you have finished playing a compact disc, always put it back in
its case.
Do not fix paper or adhesive tape to the discs and do not write on the
label.
Clean them with a special-purpose cloth.
Store your compact discs in a clean place, out of direct sunlight, where
they will not be exposed to high temperatures.
Always use compact discs marked
.
COMPACT
DIGITAL AUDIO
Before Contacting the After-Sales Service
ENG
It always takes a little time to become familiar with a new appliance.
If you have any of the problems listed below, try the solutions given. They may save you the time and
inconvenience of an unnecessary service call.
If the above guidelines do not allow you to solve the problem, take a note of:
The model and serial numbers, normally printed on the rear of the system
Your warranty details
A clear description of the problem
Then contact your local dealer or SAMSUNG after-sales service.
Problem
The system does not work
G
E
N There is no sound
E
R
A
L
Checks/Explanation
• The main lead is not correctly plugged into a wall socket or the wall socket is not
switched on.
• The remote control batteries need replacing or the polarity has not been respected.
• The STANDBY/ON button has not been pressed.
• The volume has been completely turned down.
• The correct function (TUNER, CD, USB, AUX) has not been selected.
• You have connected a set of earphones.
• The loudspeaker wires have been
disconnected.
• The Mute button has been pressed.
The Timer does not work
• The timer has been stopped by pressing TIMER ON/OFF.
In case it does not work,
even the action is taken as
above.
• Press the STOP button for 5 seconds in power ‘OFF’(standby), then it is returned the
original position (RESET)
CD
The compact disc player
/
does not start playing
MP3
I
CD
R Reception is poor or no radio
A stations are received at all
D
I
O
• The CD function has not been selected.
• The disc has been inserted face down or is either dirty or scratched.
• The laser sensor is dirty or dusty.
• The system has not been installed on a flat, horizontal surface.
• Condensation has formed in the player; leave the system in a warm, airy room for at
least one hour.
• The TUNER function has not been selected.
• The radio frequency has not been correctly selected.
• The aerial has been disconnected or is not facing the right way. Turn it until you find
the best orientation.
• You are in a building that blocks radio waves; you must use an outside aerial.
23
Technical Specifications
ENG
SAMSUNG strives to improve its products at all times. Both the design specifications and these user
instructions are thus subject to change without notice.
radio
FM
Signal/noise ratio
Usable sensitivity
Total harmonic distortion
62 dB
10 dB
0.4 %
compact disc player
Capacity Frequency range
Signal/noise ratio
Distortion
Channel separation
Disc sizes
1 disc
20 Hz - 20 KHz (± 1 dB)
90 dB (at 1 KHz) with filter
0.1 % (at 1 KHz)
75 dB
Diameter: 120 or 80 mm. Thickness: 1.2 mm
AMPLIFIER
Output power
Front Speaker (4 Ω)
Channel separation
Signal/noise ratio
60 Watts/CH RMS,IEC (total harmonic distortion: 10 %)
60 dB
70 dB
general
Power Consumption Dimensions
Weight 24
35W
230 (W) x 154 (H) x 251 (D) mm
2.2 Kg
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer
care centre.
Region
Country
ENG
Customer Care CentreWeb Site
25
AH68-02157B
Download PDF

advertising