Samsung | SAB-100 | Samsung SAB-100 User Manual

SAB-100
6.
If this product fails to operate normally, contact the store of purchase
or your nearest service center. Never disassemble or modify this
product in any way. (The manufacturer is not liable for any damage
resulting from unauthorized disassembly or repairs.)
7.
When cleaning, do not spray water directly onto parts of the product.
(Doing so may cause fire or electrical shock.) Wipe the surface with a
dry cloth. Never use detergents or chemical cleaners on the product, as
this may result in discoloration of surface or cause damage to the finish.
1.
Do not drop objects on the product or apply strong shock to it.
Keep away from a location subject to excessive vibration or magnetic
interference.
2.
Do not install in a location subject to high temperature (over 50°C), low
temperature (below 10°C), or high humidity. (Doing so may cause fire or
electrical shock).
3.
Avoid a location which is exposed to direct sunlight, or near heat
sources such as heaters or radiators. (Neglecting to do so may result in
a risk of fire).
4.
If you want to relocate the already installed product, be sure to turn off
the power and then move or reinstall it.
5.
Install in a well - ventilated location.
6.
Remove the power plug from the outlet when there is a lightning storm.
(Neglecting to do so may cause fire or damage to the product.)
Installing Manual
CAUTION
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE REAR COVER. NO
USER SERVICEABLE PARTS
INSIDE. REFER TO QUALIFIED
SERVICE PERSONNEL.
1.
2.
3.
4.
5.
This symbol indicates high voltage
is present inside. It is dangerous to
make any kind of contact with any
inside part of this product.
This symbol alerts you that
important literature concerning
operation and maintenance has
been included with this product.
Make sure that the cable is plugged in securely before using.
(A loose connection may result in fire.)
When installing the camera on a wall or ceiling, mount it safely and
securely. (A falling camera may cause personal injury.)
Do not place conductive objects (e.g., screwdrivers, coins, and metal
things) or containers filled with water on top of the camera.
(Serious injury may result from fire, electrical shock, or falling objects.)
Do not install in a sooty, dusty, or humid location.
(Doing so may cause fire or electrical shock.)
If any unusual smells or smoke come from the unit, stop using the product.
In such case, immediately disconnect the power source and contact the
service center. (Continued use in such a condition may cause fire or
electrical shock.)
Name and Function of Each Part
CONNECTOR
Alarm
IN/OUT
N/C, NO
➤ Alarm IN/OUT
The SAB-100 (Samsung Alarm Box) is a device for VPP only. Normal operation cannot be guaranteed when used for something else.
The SAB-100 (Samsung Alarm Box) is a device that receives a signal from
the sensor and outputs an alarm signal.
Checking the Contents of the Package
Make sure that the SAB-100 and the user's guide are included in the package.
SAB-100
User’s Guide
SCREW
✔ Install the SAB-100 in a cool location, away from direct sunlight. It is recom
mended that the SAB-100 is located in an area not subject to direct sunlight
during use or storage.
✔ The SAB-100 must be used in an area where temperature and humidity are
kept within the limits specified below:
- Temperature: -10°C ~ +50°C (14°F~122°F)
- Humidity: Below 90%
SAB-100 - Installation
A-IN
GND
HOT
COLD
Depending on the status of N/C and N/O, this receives an alarm and
outputs the alarm.
➤ N/C, N/O
SAB-100 Introduction
1. Choose an installation site that can sufficiently support a minimum of five
times the net weight of the equipment to be installed (approx. 500g).
2. Disassemble the SAB-100 as shown below.
NO/NC
GND
This is terminals where you can select between Normal Close and
Normal Open. Normally (when the NO/NC terminal and the GND terminal are not connected) this is set to N/O, but when the NO/NC terminal
and the GND terminal are connected, it is set to N/C.
3. Connect the cables as shown in the figure, and then use the screws to fix
the alarm box to the installation site. There should be two cables. Arrange
the so that they won't get damaged. Connect one cable to the monitor
and the other cable to the camera. Then close the case cover.
➤ CONNECTOR
One is for the camera-end of the cable, and the other is for the monitorend of the cable.
Precautions for Installation and Use
✔ Please check whether the installation site can sufficiently support the weight of
the SAB-100 before installation.
✔ Make sure that the cable is not caught on anything or its insulation sheath is
not removed. (Neglecting to do so may cause fire or damage to the product.)
✔ Prevent people from approaching the installation area, where objects might
fall during installation. Move valuables to a safe location before installation.
SAB-100 - Specifications
Item
Product Type
Power Source Voltage
Power Consumption
Operating Temperature
Operating Humidity
Physical Size
Weight
Description
Alarm Box
DC 18V From Monitor
Approx. 2W
-10°C ~+50°C
~90%
96mm(W)X35mm(H)X100mm(L)
Approx. 100g
Download PDF