Samsung | SHR-4080P | Samsung SHR-4080P User Manual

Real Time DVR
SHR-4080P User’s Manual
SHR-4080P USER’S MANUAL
Safety Regulations
Please be sure to keep the following in mind for the right use of the product to prevent proprietary risk or damage.
■
Do not use multiple plugs at once.
●
■
Do not put a vase, flowerpot, cup, cosmetics, medicine, or vessel
with water around you.
●
■
This may cause fire.
Do not disassemble, repair, or remodel the product.
●
■
This may cause abnormal operation due to high temperature.
Keep the product off direct ray of light or heat from the heating
device
●
■
This may cause breakdown.
Secure sufficient ventilation.
●
■
This may cause fire.
Keep the surrounding temperature between 0˚C to 40˚C and keep the
product off humidity.
●
■
This may cause fire or electric shock.
Do not put metals(coin, hair pin, metal piece, etc.) or inflammable
materials(match, paper, etc.) in the ventilation hole.
●
■
This imperfect connection may cause fire.
Keep the product off humidity, dust, or soot.
●
■
This may cause electric shock.
Insert the power plug firmly enough not to shake.
●
■
This may cause fire.
Do not touch the power plug with wet hands.
●
■
This may cause fire.
Do not bend the power cord forcibly nor put a heavy material on it.
●
■
This may cause abnormal heat generation or fire
This may cause fire, electric shock, or injury due to abnormal operation.
Do not pull out the power cord.
This may destroy the power cord, eventually, cause fire or
electric shock.
●
■
Plug out in the event of thunder or lightning.
●
■
Keep your children off the battery after you take it out of the product.
They tend to swallow it unconsciously.
●
■
If your children swallow it, please see the doctor immediately.
Install the product at a safe place or attach the product to the wall or
ceiling with a stand firmly enough not to fall to the ground.
●
ii
This may cause fire.
This may injure people.
Before we start
This User’s Manual describes the basic usage of SHR-4080P. This Manual contains
all the matters necessary for using SHR-4080P such as brief instruction, part name,
function, connecting other equipment, and menu setup of SHR-4080P.
-
SEC retains the copyright on this User’s Manual.
This User’s Manual cannot be copied without SEC’s prior written approval.
We are not liable for any or all losses to the product incurred by your use of nonstandard product or violation of User’s Manual.
If you want to open the system case to touch the inside, please consult with an
expert who works for the shop where you bought the product.
You may download open source codes from the following website.
(See CCTV Part of http://www.samsung.com.)
WARNING
[Battery]
As wrong exchange of the battery in SHR-4080P may cause explosion, you shall use
the certified battery for SHR-4080P.
The battery specification is as follows.
-Normal Voltage: 3V
-Normal Capacity: 220mAh
-Continuous Standard Load: 0.2mA
-Operating Temperature: -30 ~ +60˚C
[System Shutdown]
- Power-off without terminating the system in the System Shutdown menu may incur
improper motion like data loss and disk failure. Power-off shall be done in the
System Shutdown menu.
Code Certification
iii
Contents
ii
Safety Regulations
iii
Before we start
Code Certification
1
Chapter 1 Overview
1-1
1. Introduction
1-2
2. Features
1-3
3. Part Names and Functions
2
Chapter 2 Installation
2-1
1. Installation Environment Setup
2-2
2. Checking Product and Accessories
2-3
3. Additional HDD Installation
3
Chapter 3 Connecting with Other
Equipment
3-1
1. Connecting Video, Audio, & Monitor
3-2
2. Connecting SCSI Device
3-3
3. Connecting Network
3-4
4. Connecting IEEE1394 Device
3-6
5. Connecting Alarm Input/Output
3-8
6. Connecting RS-485 Device
4
Chapter 4 Live
4-1
1. System Motion
4-2
2. Live Screen Mode
4-5
3. Live Channel Selection and Audio On/Off
Setup
iv
4-6
4. Freeze and Zoom
4-7
5. Event Monitoring
4-8
6. Spot-out Monitoring
5
Chapter 5 Menu Setup
5-1
Before Use
5-2
1. System
5-12
2. Camera
5-16
3. Monitoring
5-18
4. Record Mode
5-19
5. Event Record
5-24
6. Record Schedule
5-26
7. Backup
5-27
8. Network
6
Chapter 6 PTZ Device Control
6-1
1. PTZ Control MODE
6-3
2. Basic Operation of PAN, TILT, & ZOOM
6-4
3. PRESET Setup
6-6
4. CAMERA MENU Setup
6-7
5. PRESET VIEW
6-8
6. Other VIEWs
7
Chapter 7 Recording
7-1
1. PANIC (Emergency Recording)
7-2
2. REC (Normal Recording)
7-3
3. Timer Recording
7-4
4. Event Recording
8
Chapter 8 Search & Play
8-1
Before Use
8-2
1. Calendar Search
8-3
2. Event Search
8-4
3. Date/Time Search
8-5
4. Go to First Search
8-6
5. Go to Last Search
8-7
6. Backup Data Search
8-8
7. Play
v
9
Chapter 9 Back up
9-1
1. Backup Start
9-2
2. Backup Stop
9-3
3. Backup Play
10
Chapter 10 PC Viewer
10-1
1. Introduction
10-2
2. Feature
10-3
3. Recommended PC Specification
10-4
4. Installation
10-11
5. Program Execution
10-12
6. Initial Screen
10-13
7. Monitoring Mode
10-25
8. Search Mode
10-32
9. Setup Mode
11
Appendix
11-1
1. Product Specification
11-4
2. HDD Specifications
11-5
3. Outline Drawing
11-6
4. Factory Default
11-8
5. SHR-4080P Smart Viewer Play Frame
Specification
11-9
vi
6. Troubleshooting (FAQ)
Chapter 1 Overview
1
SHR-4080P USER’S MANUAL
1
Introduction
The realTime Digital Video Recorder(DVR) compresses the camera input data from 8
channels into a MPEG4 video file and the voice input data into a G.726 audio file
respectively to record them in the Hard Disk or retrieve them from the Hard Disk
simultaneously.
In addition, it transmits the video or audio file out through a network on real time basis
so that you can monitor either file remotely by your PC.
1-1
2
Features
■
8 CH Composite Input Connectors
■
PAL Video Source Compatible
■
Able to record the normal sized (720 x 288) video image at the speed of
200IPS(image per second)
■
8 CH Loop Through Video Connectors
■
Hard Disk Overwrite Mode
■
Large Quantity Hard Disk Backup by IEEE1394
■
Able to record, play, and transmit both audio and video files to Windows Network
Viewer(Smart Viewer) simultaneously
■
Recording and Play of Audio 8CH
■
Variable Search Mode (Time/Date, Event, Camera)
■
Variable Recording Mode (Time Lapse, Event, Schedule, Emergency)
■
Extended Hard Disk Connection (SCSI, IEEE1394)
■
Alarm Interface (Input:8, Output:4, Reset:1)
■
Remote Monitoring by Windows Network Viewer(Smart Viewer)
1-2
SHR-4080P USER’S MANUAL
3
Part Names and Functions
No
Name
Power LED
1
Displays both network connection and data transmission conditions.
Back Up LED
Displays Back Up Mode.
HDD Access
LED
Indicates Normal Access to HDD.
Upon Access to HDD, LED repeats on and off.
Channel Button
Selects Single Channel in the Display Mode.
Used for Number Input Button in the Number Input Mode.
Play Back
Channel Button
Displays the Play Back screen.
8
...
9
3
0
4
Displays power on/off condition.
Network LED
1
2
Function
Audio Setup
Button
Sets up Audio On/Off.
9 Displays Split Screen.
4 Displays Split Screen.
6 Displays Split Screen.
MODE
5
Split Screen
Selection
Button
Display
Mode
MODE
6
Mode Selection
Search
Button
7 Displays Split Screen.
8 Displays Split Screen.
Displays PIP(Picture In Picture)
Screen.
Auto Sequence Mode
Enters Single Channel Screen
by the time set in MENU.
4 Displays Split Screen.
Displays the selected channel
in Full Screen.
Displays both LIVE Channel and
Play Channel in PIP Screen
simultaneously.
9 Displays Split Screen.
7
REC Button
REC
1-3
Recording starts as set in the Normal Record Mode
while LED is on.
No
Name
PANIC Button
8
PANIC
9
REC LOCK KEY
10
REC LOCK
Button
ZOOM Button
Function
Video/Audio set in the system records signals realtime. The recording resolution is Level 8 with a normal size.
Locks the REC key motion.
Sets up Digital Zoom(x2).
ZOOM
PTZ
PTZ Button
11
FREEZE
12
TELE
ALARM
13
FREEZE(TELE)
Button
ALARM(WIDE)
Performs the TELE, WIDE, PRESET, and VIEW function by pressing the PTZ button.
Performs the FREEZE function in the DISPLAY Mode.
Performs the TELE function by pressing the PTZ.
Cancels the preset ALARM function to set up a new ALARM
function.Performs the WIDE function by pressing the PTZ
WIDE
SEARCH
14
SEARCH
(VIEW) Button
Indicates the Search method.
Performs the VIEW setup function by pressing the PTZ.
VIEW
MENU
15
PRESET
MENU(PRESET)
Button
Displays the system setup menu or enters an upper menu.
Performs the PRESET setup function by pressing the PTZ.
➛
Direction
Control Button
16
❿
❷
➛
Fast
Reverse
STOP
17
18
19
Search
Function Key
20
21
JOG
SHUTTLE
PLAY/PAUSE
Changes or edits the left setup value for the
detailed menu item setup.
Moves the cursor up in a menu or increases the
setup value for the detailed menu item setup.
Changes or edits the right setup value for the
detailed menu item setup.
Moves the cursor down in a menu or decreases
the setup value for the detailed menu item
setup.
Acts as the Enter key for the menu setup.
Views the fast rewinding search screen.
Stops file searching.
Toggles during playback to activate
PLAY/PAUSE or PLAY.
Fast
Forward
Views the fast forwarding search screen.
JOG/
SHUTTLE
JOG : Used for the Forward/Reverse
Frame search.
Shuttle : Performs the Play/Reverse Play
/FF/REW function.
1-4
SHR-4080P USER’S MANUAL
1
2
3
4
5
6
7
8
9
10
11
12
13
Caution
Do not play DVR on the carpet or other soft material to prevent clogging of the air
ventilator.
To play DVR on the cabinet or rack, be sure to check the ventilation condition.
No
Name
1
VIDEO IN
2
THROUGH
You may use THROUGH port to transmit a video
signal to the other video equipment.
3
AUDIO IN
Audio Signal Input Port (RCA Jack)
4
SPOT
5
VIDEO OUT
Composite Video Signal Output Port (BNC Style
Connector)
6
AUDIO OUT
Audio Signal Output Port (RCA Jack)
7
VGA
8
S-VIDEO
9
NETWORK
10
SCSI
11
IEEE1394
ALARM
12
13
1-5
Function
Composite Video Signal Input Port (BNC Style
Connector)
AC-IN
SPOT Out Output Port (BNC Style Connector)
VGA Video Signal Output Port
S-VIDEO Video Signal Output Port
Network Connection Port
SCSI Type Device Connection Port
IEEE1394 Type Device Connection Port
- ALARM IN 1~8 : Alarm Input Port
- ALARM RESET IN : Alarm Reset Port
- ALARM OUT1~4 : Alarm Output Port
- TX+, TX-, RX+, RX- : RS-485 Communication
Port
AC 100~230V Power Socket Support
Chapter 2 Installation
2
SHR-4080P USER’S MANUAL
1
Installation Environment Setup
Do not play DVR on the carpet or other soft material to prevent clogging of the air
ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition.
You shall pay attention to the following before you use the product.
1. Do not use it outdoor.
2. Do not let water or liquid in the connection part or the product itself.
3. Do not impose excessive shock or force.
4. Do not pull out the power plug unreasonably.
5. Do not disassemble the product on your own.
6. Do not exceed the rated input or output range.
7. Use certified power cord only.
8. Match a product with an input ground with a power cord with a ground.
2-1
2
Checking Product & Accessory
Upon delivery of a product, you shall unwrap the product and put it on the even floor
or where you want to use it. Then you shall check if the following items are in it.
Main Body
■ User’s Manual
■ One Power Cord
■ Two Brackets
- Brackets are used to attach the product to the rack.
■ Smart Viewer Software CD (Incl. PDF Manual)
■ 12 Screw Specials
- Please keep screw specials well to be used for HDD addition.
■ 2 EA of RS-485/Alarm Terminal Block
■
2-2
SHR-4080P USER’S MANUAL
3
HDD Addition
You may add up to 3 more HDDs to the product.
However, since the product contains has many parts which may incur electric shock,
accident, or product breakdown and improper installation or setup may disturb HDD
recognition or normal product operation, you shall consult with an expert of the
agency where you bought the product.
[Caution for HDD Addition]
■
■
■
Do not let the cable stuck improperly nor uncoated. (This may cause breakdown or fire.)
Be careful not to cut yourself by sharp edges of the product.
Be careful not to miss the disassembled screws or parts. Imperfect assembly due
to short of screws or parts may cause breakdown or malfunctioning.
[HDD Addition Procedure]
1. Loosen screws on both sides(5 points) and back(1 point) to detach the product cover.
DIGITAL
2-3
VIDEO RECO
DER SHR-4
080
2.Detach the cover from the product. (Pull out the cover slightly and lift from the back
side to detach.)
3. A bracket is fixed to each side of HDD. Please loosen the screw of the bracket to
which you want to fix HDD.
BRACKET-HDD
2-4
SHR-4080P USER’S MANUAL
4.Pull BRACKET-HDD to the product center to detach the fixed part at the bottom to
detach BRACKET-HDD from the product.
5.Tighten 4 SCREW-SPECIALs(BWH,6-32UNC,L10.5), supplied as an accessory to
fix HDD to BRACKET-HDD. (Screw tighten force shall be strong enough to resist
vibration.)
2-5
6. Restore HDD installed BRACKET-HDD.
(Assembly shall be done in the reverse procedure of disassembly as follows. Align the 5 fixing points at the bottom with the BRACKET-HDD fixing holes respectively and push BRACKET-HDD out of the product to align the screw fixing holes. Then, tighten the screws firmly.)
7. Check if BRACKET-HDD has been fixed to the product and connect both the power
supply cable and the signal transmission cable (IDE CABLE) to the HDD.
Signal Transmission
Cable (IDE Cable)
Power Supply Cable
2-6
SHR-4080P USER’S MANUAL
8. Check the connector, wiring, and cable fixing condition inside the product and close
the cover.
9. Tighten cover-fixing screws. (5 points on both sides and 1 point in the back side)
✻ You can apply 2 HDDs to each BRACKET-HDD as shown in the figure.
Attention
For HDD addition, please select the same HDD with the existing HDD fixed to the
product as far as possible. This product can accept 4 more HDDs, 2 at Primary Slot
and 2 at Secondary Slot respectively. Both HDDs attached to Primary Slot and
Secondary Slot shall be set to Master and Slave respectively. Refer to User’s Manual
for Master or Slave Jumper Setting.
In the event of only one HDD installation, it shall be inserted into the Primary slot.
Note
Refer to Appendix 2 to see which HDD specifications are supplied.
2-7
Attention
! Regarding the sub fan, you need additional brackets and sub fans as follows.
The sub fan is shaped like this when viewed from the front and back. Please pay
attention to the fan direction to let wind go through the fan.
@ Fix the fan as follows.
2-8
SHR-4080P USER’S MANUAL
# Please install the fan to be seen from the front view of the set.
2-9
Fixing the fan to the left.
2-10
Chapter 3 Connecting
with Other Equipment
3
SHR-4080P USER’S MANUAL
1
Connecting Video, Audio, and Monitor
3-1
2
Connecting SCSI Device
●
The SCSI interface of SHR-4080P is used for backup or extended storage.
Connect an armored SCSI hard disk drive cable to the high-density 50-pin female
Ultra SCSI port. SCSI device ID adopts 0 through 5 with 6 connections at most.
Note
The SCSI bus shall be terminated properly. Otherwise it may not operate.
Refer to Appendix 2 to see which HDD specifications are supplied.
Caution
Never connect or disconnect a SCSI device while DVR is turned on.
The system is not able to recognize the SCSI device while DVR is running.
3-2
SHR-4080P USER’S MANUAL
3
Connecting Network
3-3
●
Connecting to Internet through Ethernet(10/100BaseT)
●
Connecting Internet through ADSL
4
Connecting IEEE1394 Device
●
●
●
Connect the IEEE1394 hard disk through the back port of SHR-4080P.
You can connect up to 6 IEEE1394 armored hard disks by the Daisy-Chain
method.
After connection, Menu - System - HDD Setup is necessary for recognition and
setup for use.
Caution
The IEEE1394 Device hard disk shall be set to Master.
●
●
It acts as HOT PLUG to connect or disconnect the IEEE1394 device while the system is running.
If you press Connect/Disconnect in Menu - System - HDD Setup, HOT PLUG will
be recognized or deleted.
Note
See 5-8 System (HDD Setup) of User’s Manual.
Caution
- Wait until the HOT PLUG connected hard disk is stabilized enough (approx. 2 seconds per each hard disk) and click CONNECT in SHR-4080P MENU before use.
- Be sure to click DISCONNECT in SHR-4080P MENU to delete IEEE1394 Device
safely. Failure of clicking DISCONNECT may cause improper operation of IEEE1394
Device.
3-4
SHR-4080P USER’S MANUAL
Note
Refer to Appendix 2 to see which HDD specifications are supplied.
3-5
5
Connecting Alarm Input/Output
The Alarm IN/OUT port in the back of SHR-4080P is composed of the following
elements.
●
ALARM IN/OUT Connection
Name
1
- ALARM
- ALARM
- ALARM
- ALARM
- ALARM
- ALARM
- ALARM
- ALARM
- ALARM
IN1
IN2
IN3
IN4
IN5
IN6
IN7
IN8
RESET IN
- ALARM
- ALARM
- ALARM
- ALARM
OUT1
OUT2
OUT3
OUT4
2
3
Function
ALARM Input Port
On receiving an ALARM RESET signal, the
system cancels the current ALARM input or
output signal and resumes sensing.
ALARM Output Port
3-6
SHR-4080P USER’S MANUAL
●
3-7
ALARM IN/OUT Connection
6
Connecting RS-485 Device
●
Connect RS-485 Device through the back port of SHR-4080P.
●
You can install and control the PTZ camera supporting RS-485 communication.
●
You can adopt either Half Duplex or Full Duplex method for the connection.
PTZ Camera
SHR-4080P
Rear
Half Duplex Type
Data (–)
Tx(–)
Data (+)
Tx(+)
Full Duplex Type
Rx(+)
Rx(–)
Tx(–)
Rx(–)
Rx(+)
Tx(+)
●
Baud Rate covers 600, 1200, 2400, 4800, 9600, 19200, and 38400.
Caution
Check if RS-485 Device is compatible with SHR-4080P first. Then pay attention to
the polarity of RS-485 which has two poles, + and -.
3-8
Chapter 4 Live
4
SHR-4080P USER’S MANUAL
1
System Motion
●
Turn the power on and the following LOGO screen pops up.
●
After the LOGO screen appears, the button in front of SHR-4080P blinks 6 times
to initialize the system for operation.
●
Upon completion of normal initialization, the Live screen appears accompanying a
beep sound.
●
It requires 30 to 40 seconds until the Live screen appears.
Note
A new HDD may require more time for the initialization until the Live screen
appears due to the initialization period of the new HDD.
If the Live screen does not appear at all or the button in front of SHR-4080P repeats
blinking, please check the connection across the product body. If you find any error,
please ask the shop where you bought the product.
●
The Live screen does not affect the earlier MENU setup. If you reboot the system
after power-off during recording, the Live screen will appear, accompanying
recording.
Note
If you see no more Live screen, you shall check if video data comes out in Composite
mode or VGA mode.
If you whish to change the video output mode, you shall hold on to the MODE button in front of SHR-4080P and keep pressing the 0 button for 5 seconds. Then, the
front button will repeat on and off.
4-1
2
Livescreen Mode
Definition of Live Screen Icon
The Live screen icons of SHR-4080P display the current setup and function status of
each screen.
N
PTZ
CAM_01
V.Loss
CAM_01
P E S : Recording Icon
Each icon represents Normal / Panic / Event(Alarm+Motion) / Schedule Recording.
L
N
S : Recording Video Size Icon
Each icon represents the recording size of Large(Full D1: 720x576) / Normal(Half D1:
720x288) / Small(CIF: 352x288).
PTZ
: PTZ Icon
This icon appears when you set up PTZ device with the PTZ icon and turns yellow
when you execute PTZ.
: Audio Icon
This icon represents Audio On/Off status and turns yellow for On. It does not appear
for Video or Audio Disable.
: Sensor In Event Icon
This icon appears in the channel synchronized with the external sensor signal input
with Sensor On.
: Motion Event Icon
This icon appears in the Motion Event channel with Motion Detection On.
: Zoom Icon
This icon appears with Zoom On or Zoom In and disappears when you cancel Zoom On.
: Freeze Icon
This icon appears in the Freeze mode and disappears when you cancel Freeze.
4-2
SHR-4080P USER’S MANUAL
: Auto Sequence Icon
This icon appears in the Auto Sequence mode.
V.Loss / V.Off : Video Input Status
If there is no more video data input with Video On, [V.Loss] appears in the channel. If
you set Video On/Off to Off, [V.Off] will appear.
Definition of Live Screen Mode
SHR-4080P receives 8 live images and displays them in the following 8 modes.
CAM_02
CAM_01
CAM_01
CAM_02
CAM_03
Single Mode
CAM_02
CAM_04
Quad 1,2 Mode
CAM_01
CAM_02
CAM_03
CAM_04
CAM_05
CAM_06
CAM_07
CAM_08
CAM_01
CAM_01
CAM_03
CAM_04
CAM_05 CAM_06
6 Split Mode
CAM_02
CAM_04 CAM_05
CAM_03
CAM_06 CAM_07
7 Split Mode
CAM_03
CAM_01
CAM_04
CAM_05 CAM_06 CAM_07 CAM_08
8 Split Mode
●
9 Split Mode
CAM_01
CAM_02
PIP Mode
CAM_01
Auto sequence Mode
Full Screen(Single) Mode:
Displays the selected channel in a full screen. Then, the channel LED concerned
will be turned on.
●
4, 6, 7, & 8 Split Mode:
Four, six, seven, and eight video channels are split in the screen and each channel LED is turned on. You are able to choose a channel as you want to in each
split mode.
●
9 Split Mode:
Splits all the video input from CH1 to CH8 into 9 screens and LEDs of CH1 to CH8
are all turned on. You are not allowed to choose a channel in this mode.
●
PIP(Picture in picture) Mode:
Displays a one-ninth sized screen in the full screen and the channel LED concerned is turned on. You are able to choose a channel as you want to, which is
displayed in the full screen or reduced screen area. You may move the PIP screen
at 5 stages in the Full screen with the
or ❷key.
●
Auto sequence Mode:
Displays the time when FULL SCREEN has been set to each channel in sequence
and the channel LED concerned is turned on.
4-3
Selecting Live Screen Mode
Each mode may be selected by [MODE Button] and [CH1 ~ CH8 Button]. The following figure shows Live Mode of SHR-4080P after converted.
●
The default is 9 Split Screen Mode.
●
The default of 4 Split Screen Mode is [4 Split 1] Mode to display [CH1 ~ CH4] or [4
Split 2] Mode to display [CH5 ~ CH8].
●
You are able to choose other modes than Full Screen Mode with [MODE Button] in
sequence. Whenever you press [MODE Button], the system will enter [9 Split]➝[4
Split 1]➝[4 Split 2]➝[6 Split]➝[7 Split]➝[8 Split]➝[PIP]➝[Auto sequence]➝[9 Split]
Mode one by one.
●
If you press [CH1~CH8 Button], you will be able to see the full screen of each
channel.
●
The MODE button is used to return to the previous split mode screen from a full
screen mode.
4-4
SHR-4080P USER’S MANUAL
3
Live Channel Selection and Audio On/Off Setup
In other split modes than Full Screen Mode, 9 Split Mode, and Auto Sequence Mode,
you may choose a channel to be displayed in each split area on your own. Meanwhile,
the channel whose MENU is set to Audio On can set up Audio On/Off in all Live Modes.
Audio On/Off Setup in Full Screen
In Full Screen Mode, the selected channel Audio is automatically turned on and you
may set up Audio On/Off with the Audio Setup button [0 Button]. Depending on the
Audio On/Off setup condition, the Audio Setup button [0 LED] is turned on or off.
Audio On/Off Setup in 9 Split Mode
If you press [ENTER Button] in 9 Split Mode, the selection cursor in the following figure
will appear and the channel concerned will be selected. If you press the Audio Setup
button [0 Button] with a channel selected, you may set up Audio On/Off for the channel
concerned. Depending on the Audio On/Off setup condition, the Audio Setup button [0
LED] is turned on or off. You are not allowed to choose a channel in this mode.
CAM_01
CAM_02
CAM_03
CAM_04
CAM_05
CAM_06
CAM_07
CAM_08
Channel Selection and Audio On/Off Setup in 4,6,7,8 Split
Mode and PIP Mode
As in 9 Split Mode, the selection cursor will appear if you press [ENTER Button] in both
4,6,7,8 Split Mode and PIP Mode to select a channel. With a channel selected, you may
not also choose a channel on the current screen with the [CH1 ~ CH8] button but also
set up Audio On/Off with the Audio Setup button [ 0 ] as in 9 Split Mode. Depending on
the Audio On/Off setup condition, the Audio Setup button [ 0 ] is turned on or off.
Audio On/Off Setup in Auto Sequence Mode
The default of Auto Sequence Mode is set to Audio On and Audio changes channel by
channel. You may set up Audio On/Off with the Audio Setup button [0 Button] and the
Audio Setup button [0 LED ] is turned on or off depending on the Audio On/Off setup
condition.
4-5
4
Freeze and Zoom
Freeze Function
Freeze pauses the video image in Live Screen, only available in Live Mode. You can set
up Freeze On/Off with [FREEZE Button] and [FREEZE LED] is turned on or off depending on the Freeze On/Off setup condition.
Zoom Function
Zoom enlarges the selected area twice, only available in Full Screen Mode.
If you press [ZOOM Button] in Full Screen Mode, the zoomed area will appear now you
are able to adjust the selected area position. If you select an area and press [ENTER
Button], the area will be displayed in double size. If you press [ENTER Button] again,
the previous screen to select Zoom area will appear again and you will be capable of
Zoom Off with [ZOOM Button] after the screen is enlarged. Depending on the Zoom
On/Off setup condition [ZOOM LED] is turned on or off.
4-6
SHR-4080P USER’S MANUAL
5
Event Monitoring
Event Monitoring displays the channel synchronized with a specific event
(Sensor/Motion/Video Loss) on the screen when it occurs. Event Monitoring On/Off
and Event Duration setup is available in [Menu]➝[Monitoring].
If you set the Event Monitoring interval to 5 seconds and an event occurs at CH2 in
the beginning as in the following figure, the system will display CH2 in the whole
screen for 5 second. Another event within 5 seconds will be displayed together with
the existing event. In the following figure, both CH1 and CH3 events occur within 5
seconds (for example, in 4 seconds) after the CH2 event, the three events are split
into 4 screens.
Likewise, CH2, CH5, and CH7 events within 5 seconds after both CH1 and CH3
events are integrated with the existing 2 events and all the 5 events are split into 9
screens. Without further event during Event Duration, the system will return to the previous Live Mode.
If you press [ALARM Button] during Event Duration, Event Monitoring will stop. On
sensing an event, [ALARM LED] is turned on. If you press [ALARM Button] now,
[ALARM LED] will go out.
Audio On/Off setup is also available during Event Monitoring and its default is set to
Audio On. In case of event occurrence at a certain channel, Audio of the channel is
On while the lowest channel Audio is on in case of simultaneous occurrence of more
than one event since the lowest channel has the first priority. You may use [CH0
Button] to alter the Audio On/Off setup condition, on the basis of which [CH0 LED] is
turned on or off.
4-7
6
Spot-out Monitoring
Spot-out Monitoring has nothing to do with Live Screen Output, monitoring the full
screen of a certain channel. If you select Monitoring in the MENU screen, you can
make a channel among CH1 to CH8 spot out or you can output channels one by one
at an interval as Auto Sequence Mode of Live Mode. The interval is as same as the
forwarding time of Auto Sequence Mode of Live Mode. If you set Spot-out Event
Monitoring to On, you will be able to spot out the event channel. In case of simultaneous event occurrence at more than one channel, the lowest numbered event channel
has the first priority to be spotted out.
Caution
If the built-in HDD is not connected, or it operates with power applying in error,
(
) indicating "built-in HDD error" is displayed at the top of left.
At this time,
(1) Live screen mode
(2) Monitoring mode by Smart Viewer
operate only and the other functions including recording, search, playback, menu
setup, and PTZ do not operate.
If the above problem is occurred, Be sure to contact a service center to settle the
problem.
4-8
Chapter 5
Menu Setup
5
SHR-4080P USER’S MANUAL
Before Use
5-1
●
Selection
The yellow cursor shows the current window. Use the ,❷,➛, or ❿ key in the
front to move the cursor on your desirous menu. If you press the “Enter” key with
the cursor clicking on your desirable menu, the system will enter the new mode.
Press the “Enter” key to finish selection. On seeing Drop Down Menu, use the
or ❷ key to move the cursor on your desirable menu.
●
“OK” or “Cancel” in Menu Setup Window
Once changed, the new menu setup procedure will be finalized by pressing “OK”.
Pressing “Cancel” will cancel the previous setup and return to the upper menu.
●
Front “MENU” and “SEARCH” Button
The MENU button or SEARCH button, if pressed first, acts as an entrance button.
Once entering, it reverses the page to the previous one.
●
The “>” or “V” mark beside the title copies the line in the arrow direction to the
value of the first line.
●
The first page of the menu is structured as follows.
1
System
●
System Menu has the following items in detail.
Date/Time/Language Setup
●
Date
Press the “Enter” key and the ➛ or ❿ key to move to Y/M/D. Use the
to change the date. Press the “Enter” key to come out of the mode.
●
or ❷ key
Time
Press the “Enter” key and the ➛ or ❿ key to move to H/M/S. Use the
or ❷ key
to change the time. Press the “Enter” key to come out of the mode. Once changed,
the date and time will remain unchanged until you press “OK” or “Cancel”.
5-2
SHR-4080P USER’S MANUAL
Note
[Date/Time Change]
Pressing “OK” after you change date and time, you will be asked by a pop-up window if you really confirm the change. Here, press “Yes” to change the time. Since
Date/Time does not change in backup/recording process, be sure to stop the
backup/recording process before you change Date/Time.
Caution
[Date/Time Change]
If you restore Date/Time to the original value, the data recorded before the restoration may be deleted. For example, if you restore 8 am to 7 am, all the data recorded
between the times will be deleted.
●
Date Format
This supplies 3 formats, Year-Month-Date / Date-Month-Year / Month-Date-Year.
●
Time Format
This supplies 2 formats, 24 Hour / 12 Hour(AM/PM).
●
Language
After you select a language, OSD is expressed in the selected language. The
available languages are added in the list.
●
Summer Time
Summer Time sets the watch one hour faster than the local standard time. This
makes the system count for Summer Time in Summer Time regions. Being the
Summer Time setup date, the set goes one hour faster and starts rebooting.
Set to Off, Summer time does not operate. Then, you are unable to enter the right
date menu. Set to On, you can set the start time on the left and the end time on
the right on the basis of ‘~’. Summer Time is allowed to set Month/Date/Time only.
Year/Minute/Second remains inactivated.
Note
[Summer Time Setup]
Backup in progress will be cancelled. Recording in progress will be suspended for a
moment until rebooting.
Caution
[Summer Time Setup]
As the system goes one hour earlier, the data recorded since an hour ago will be
deleted. As Summer Time activates at the preset time, you are recommended to take
the utmost care of preventing any trouble incurred by data deletion or rebooting.
5-3
Password
●
The Default Password is 4321.
●
New Password
This is used to change the system password inside SHR-4080P. You are allowed
to create a password up to 8 digits. Press the “Enter” key and then a channel button from 0 ~ 9 on your left to finish input. If you press the “Enter” key after change,
the system will automatically turn to “New Password Confirm”.
●
New Password Confirm
This confirms a new password. You shall be obliged to input New Password in the
above row first. Without New Password input, New Password Confirm input has no
effect.
●
Password Lock
Pressing the “Menu” button while it is set to On, you will be asked by a pop-up
window of the password. Pressing the “Menu” button while it is set to Off, you will
enter Menu Mode immediately, not being asked of the password.
●
All Key Lock On
If you select this, the system will enter Live Mode immediately. If you press a button in the front, the Password window will pop up. Succeeding in Password input
will be followed by Key Lock cancellation after such a message window pops up.
Note
[All Key Lock On]
If you select this, the system will enter Live Mode immediately and keys will be
locked.
5-4
SHR-4080P USER’S MANUAL
Load Factory Default
●
This initializes all the menu preset values. The recorded data will not be deleted.
Press “OK” in the confirmation window to start initializing.
System Log
5-5
●
System Log is used by a controller to check crucial records.
●
This displays such contents of a system related log and its execution date/time as
System Start, System Termination, and Menu Setup Change.
●
First : Returns to the first Log page.
●
Prev : Back to the previous Log page.
●
Next : Forwards to the next Log page.
●
Last : Moves to the recent Log.
●
System Log List
System Start
Login(Admin)
Logout(Admin)
Login(User)
Logout(User)
Setup Start (Local)
Setup End (Local)
Setup (Remote)
Play Back Start
Play Back End
Record Start CH[n]
Record End CH[n]
Power Failure Recovery
System Start
Viewer Login (Admin)
Viewer Logout (Admin)
Viewer Login (User)
Viewer Logout (User)
Set: Menu Entering
Set: Menu Escape
Viewer:Menu Setup
Play Start
Play End
Channel [n] Record Start
Channel [n] Record End
System Restoration
after Power Failure
Panic Record Start
Panic Record End
Time Change
Load Factory Default
System Upgrade
Disk Full
Backup Start
Backup End
Backup Stop
Backup Fail
ATA HDD Erase
IEEE1394 HDD Erase
SCSI HDD Erase
Panic Record Start
Panic Record End
Date/Time Change
System Initialization
System S/W Change
No Space for HDD
Backup Start
Backup End
Backup Stop
Backup Failure
ATA Data Deleted
IEEE1394 Data Deleted
SCSI Data Deleted
Event Log
●
Checks the record regarding Event like Alarm / Motion / Video Loss
●
This displays the contents of a log regarding Event its execution date/time.
●
First : Returns to the first Log page.
●
Prev : Back to the previous Log page.
●
Next : Forwards to the next Log page.
●
Last : Moves to the recent Log.
●
Event Log List
Video Loss CH[n]
Channel [n] Image Disturbance
Alarm Detection CH[n]
Channel [n] Alarming
Motion Detection CH[n]
Sensing Channel [n] Motion
5-6
SHR-4080P USER’S MANUAL
System Information and Setup
●
●
Software Version : Displays the current version. Setup is not available.
Broadcast Format : Displays the current Format(NTSC/PAL) . Setup is not available.
●
Mac Address : 6 Byte hardware address. Setup is not available.
●
HDD Erase
This erases the data in ATA / IEEE1394 / SCSI. Click the checkbox of the device
that you want to erase and press “OK” You are not allowed to erase the data in
Recording or Backup progress.
Note 1
Being a physical hard disk inside the SHR4080 main body connected by an IDE
cable, this stores data.
[External HDD]
Being a physical hard disk connected with the port and terminal in the back of the
SHR4080 main body, this stores data.
This can be used as Extended HDD or Backup HDD.
- Extended HDD : Supplements Internal HDD quantity. Connected, it takes the place
of Internal HDD.
- Backup HDD : Backs up the data recorded in the set.
Note 2
[ATA]
Usage : Internal HDD
[SCSI]
Usage : External HDD (Extended HDD or Backup HDD)
A physical hard disk connected with the SCSI port in the back of the SHR4080 main
body
[IEEE1394]
Usage : External HDD (Extended HDD or Backup HDD)
A physical hard disk connected with the IEEE1394port in the back of the SHR4080
main body
5-7
Caution
[HDD Erase]
Data will not be deleted in backup or recording process.
Please be sure to suspend backup or recording before you delete any data.
HDD Setup
Internal
●
HDD Information
Displays the number, quantity, and status of ATA, IEEE1394, and SCSI. Setup is
not available.
Status : Internal HDD, External HDD, Backup HDD
●
External HDD Setup
1. Backup/External
You are able to determine the usage of IEEE1394 and SCSI.
Not Defined ➝ When the connected HDD usage is not defined. Expressed in
External or Backup.
No Device ➝ When no HDD is connected. You are able to press right TAB after
you connect HDD.
External ➝ When the connected HDD is set to External. It may used as a back
up HDD if you press the “Enter” key and turn to Backup.
Backup ➝ When the connected HDD is set to Backup. It may used as an
External HDD if you press the “Enter” key and turn to External.
5-8
SHR-4080P USER’S MANUAL
2. Hot Plug - Connect/Disconnect
You may connect or disconnect IEEE1394 Hard Disk while power is supplied to
the SHR-4080P main body.
① As for connecting, connect IEEE1394 Hard Disk with the SHR-4080P main
body and press “Connect”. Pressing “Connect” makes the SHR-4080P main
body recognize all connected IEEE1394 Hard Disks.
➁ As for disconnecting, be sure to press “Disconnect” and detach IEEE1394
Hard Disk from the SHR-4080P main body safely.(Be sure to pause recording
or backup process.) Pressing “Disconnect” cancels and detaches all
connected IEEE1394 Hard Disk.
Caution
[ IEEE-1394 Hot-Plug Connect/Disconnect Function ]
You may connect or disconnect SCSI while power is supplied to the SHR-4080P main
body. Only IEEE1394 supports the Hot-Plug function.
[Backup HDD]
SCSI and IEEE1394 cannot be used as Backup HDD simultaneously.
IEEE1394 shall be set to External to use SCSI as Backup.
SCSI shall be set to External to use IEEE1394 as Backup.
Disk Mode Setup
●
Disk End Mode
Stop : Stops recording when HDD is full during recording.
Overwrite : Deletes the original data and save a new data when HDD is full
during recording.
Please delete the HDD data to change the initial mode.
☛ To delete data, please refer to the following menu. 5-7. System Information and
Setup
●
Disk End Beep
On : Beeps when HDD is full during recording.
Off : When HDD is full, the beep sound is not heard.
5-9
Caution
[Disk End Mode Overwrite]
In Overwrite Mode, the previous Event data may be deleted.
Remote control Device
MENU for Samsung Integrated Remote Control(SSC-2000)
Remote Control Device
Device
●
Samsung System Keybord
ID
Baudrate
Parity
Date
Stop
Duplex
03
4800
None
8
1
Half Duplex
Device
A Remote Control Device, being connected to the RS485 port.
●
ID
Unique ID of SHR-4080P
This unique ID is essential as SSC-2000 can control multi SHR-4080 DVRs.
●
Baudrate
Baudrate to communicate with SSC-2000
Be sure to be identical to SSC-2000 Baudrate for communication.
●
Parity
Sets up one of None / Even / Odd.
●
Data
Sets up either 7 or 8.
●
Stop
Sets up either 1 or 2.
●
Duplex
Sets up either Half Duplex or Full Duplex.
Note
If you select Remote Control Device, you may not PTZ Camera with SHR-4080P. The
PTZ button in front of SHR-4080P becomes inactivated.
Press the PTZ button and the PTZ ban icon(
) will appear. It’s because the RS485 port setup was done for Romote Control Device.
5-10
SHR-4080P USER’S MANUAL
System Shutdown
Remote Control Device
●
Terminates the work in action safely and turns the power off. Press “OK” in the
confirmation window and plug out when you see “Safe to Power Off”.
Caution
[System Shutdown]
Power-off without terminating the system in the System Shutdown menu may incur
improper motion like data loss and disk failure. Power-off shall be done in the
System Shutdown menu.
5-11
2
Camera
●
The detailed Camera Menu items are as follows.
Camera Configuration
●
Video
On : Camera images from a selected channel appear.
Off : Camera images from a selected channel disappear. In this case, you are not
allowed to set Audio/Title/Auto Seq.
●
Audio
On : You can hear voices from a selected channel.
Off : You cannot hear voices from a selected channel.
5-12
SHR-4080P USER’S MANUAL
5-13
●
Title
You can name the camera of a selected channel.
If you press the Enter key, the Virtual keyboard will come out.
❿ Virtual Keyboard
If you move the cursor, you can type text by text.
Up to 15 texts can be typed.
Keyboard cannot be composed of all spaces.
Pressing Caps Lock changes the keyboard that can be selected. (2 Modes)
●
You may define the duration of each channel at the Auto Sequence channel in Live
Mode. A channel, set of Off, does not operate in Auto Sequence Mode.
PTZ Device
●
ID
PTZ Camera ID from 0 to 255
●
Protocol
A protocol supported by PTZ Camera
The following protocols are now being supported.
Samsung/ Vicon/ Panasonic/ AD/ Philips/ Erna/ PelcoD/ PelcoP/Vcltp/ Diamond/
Kalatel
●
Baudrate
Baudrate supported by PTZ Camera, 600/ 1200/ 2400/ 4800/ 9600/ 19200/ 38400
●
Parity
Defines one among None, Even, and Odd.
●
Data
Defines either 7 or 8.
●
Stop
Defines either 1 or 2.
●
Serial Mode
Defines either Half Duplex or Full Duplex.
Caution
The above items shall be aligned with the PTZ Camera setup condition.
For the details, please refer to User’s Manual of the PTZ Camera manufacturer.
5-14
SHR-4080P USER’S MANUAL
Screen Setup
●
This is a window to adjust Brightness/Contrast/Color for the camera image of each
channel. Put the cursor on the channel that you want to adjust and set up
Brightness/Contrast/Color. Once selected, the channel appear in the PIP area on
the right. Press the
or ❷ key to adjust the value from 0 to 100.
●
If you select CH ✓, all the channel values will become the same as the finally
selected channel value.
●
“Default” resets the current channel to the basis value of 50.
Note
[Screen Setup Change]
During backup or recording process, the Screen Setup information remains
unchanged.
Be sure to stop backup or recording process before you change the information.
5-15
3
Monitoring
●
Event Monitoring
You are able to set to Off/3sec/5sec/10sec/20sec/30sec/Continuous.
① Off : Event Monitoring does not operate to turn to the screen where an event
occurs.
➁ 3sec/ 5sec/ 10sec/ 20sec/ 30sec : For the period, the screen is seen before the
next screen appears.
➂ Continuous : The Event Monitoring screen remains alive until you press the front
“Alarm” button to cancel the screen manually.
●
OSG Display
① Date : The date is displayed on the screen or not depending Date remains On or Off.
➁ Time : The time is displayed on the screen or not depending Time remains On or Off.
➂ Title : The title is displayed on the screen or not depending Title remains On or Off.
➃ Status : Audio/Ptz is displayed on the screen or not depending Status remains
On or Off.
●
Spot Out Channel
Spot Out channel is used to let one of two monitors monitor a channel, focusing on
it. Spot Out channel supplies two functions, continuous monitoring of only one
channel and Auto Sequence to display all the channels one by one.
① Auto Seq. setup ranges from Ch1 to Ch8.
➁ Set to Auto Seq., Spot Out channels are displayed in turn.
➂ Auto Seq. Duration is as same as determined for Camera Configuration.
●
Spot Out Event Monitor
Determines if event monitoring will be executed for Spot Out channels.
① Off : dose not event monitoring in Spot out channel.
➁ 3sec/ 5sec/ 10sec/ 20sec/ 30sec : Duration options on the screen before it
scrolls down.
➂ Continuous : Once scrolled down, the screen remains displayed until you delete
“Alarm” LED in front manually.
5-16
SHR-4080P USER’S MANUAL
●
Monitor Out
You are not allowed to connect VGA MONITOR and Composite MONITOR simultaneously. Consequently, the user are obliged to choose either Composite Output
or VGA Output.
① Composite : Output comes out of the “Composite Out” port.
➁ VGA : Output comes out of the “ VGA Out” port.
Any change from Composite to VGA or vice versa reboots the system
automatically.
●
PB( Playback ) Channel Position
Designates the position of a channel to be played back in Play Back 9 Split Mode.
Right Down : Designates a location on the bottom right corner.
Center : Designates a location in the center.
Caution
[Monitor Out]
Set to Composite Output, VGA does not come out.
Set to VGA, Composite Output does not come out.
If you hold on to the MODE button in Live Mode and keep pressing the 0 button for
5 seconds, the status will change from VGA to COMPOSITE or vice versa accompanying rebooting.
5-17
4
Record Mode
If you press the front “REC” key, the mode to be recorded will be determined.
☛ For Event Recording Mode value setup, refer to 5-18. Event Record
Mode Setup Menu.
●
Mode
On : Pressing the REC key starts recording the current channel.
Off : Even pressing the REC key does not affect current channel recording.
The default is set to “On”.
●
Video Size
Determines the size of a screen to be recorded.
Full D1 : 720x576 (L) ➝ Large
Half D1 : 720x288 (N) ➝ Normal
CIF : 352x288 (S) ➝ Small
Note
[Monitor Out]
You are not allowed to set up Video sized “Full D1” and “25ips” of Rate simultaneously. The system does not support both at once.
●
Quality
Recording resolution will be determined.
Choose one from Level 1(Low) to Level 8 (High).
Level 8 supplies the best resolution
●
Rate
Determines Frame Rate to be recorded. Frame Rate means the number of screen
recorded every second.
Set to 25ips, the system records too many screens per second and play continues
intermittently since recording is more detailed. This is appropriate for concentrated
monitoring zone setup.
25 ips/ 12.5 ips/ 8.33 ips/ 6.25 ips/ 5 ips/ 2.5 ips/ 1 ips
Note
[Monitor Out]
You are not allowed to set up “25ips” of Rate and Video sized “Full D1” simultaneously. The system does not support both at once.
5-18
SHR-4080P USER’S MANUAL
5
Event Mode
●
The detailed items of Event Record Menu are as follows.
Evnet Record Mode
Determines a mode to be recorded when an event occurs.
●
V. Size (Video Size )
Determines the size of a screen to be recorded.
Full D1 : 720x576 (L) ➝ Large
Half D1 : 720x288 (N) ➝ Normal
CIF : 352x288 (S) ➝ Small
Note
[Monitor Out]
Simultaneous setup of "Full D1" in Video Size and "25ips" in Rate is prohibited. This
is not supported by the system.
5-19
●
Quality
Recording resolution will be determined.
Choose one from Level 1(Low) to Level 8 (High). Level 8 supplies the best resolution
●
Rate
Determines Frame Rate to be recorded. Frame Rate means the number of screen
recorded every second.
Set to 25ips, the system records too many screens per second and play continues
intermittently since recording is more detailed. This is appropriate for concentrated
monitoring zone setup.
25 ips/ 12.5 ips/ 8.33 ips/ 6.25 ips/ 5 ips/ 2.5 ips/ 1 ips
Note
[Monitor Out]
You are not allowed to set up “25ips” of Rate and Video sized “Full D1” simultaneously. The system does not support both at once.
●
PreAlarm
Pre Alarm Section
Event occurred point of time
Records the situation until Alarm is issued.
Off : No recording
5sec/ 10sec/ 20sec/ 30sec : The recording time options before Alarm issue
●
PostAlarm
Post Alarm Section
Event occurred point of time
Records the situation since Alarm is issued.
Off : No recording
5sec/ 10sec/ 20sec/ 30sec/1min/3min/5min/10min/20min :
To this, the recording time after Alarm issue is set.
5-20
SHR-4080P USER’S MANUAL
Alarm
●
Sensor State
Off : Sensor does not operate.
① N.O(Normal Open) Sensor : Sensor remains open all the time and if closed, an
alarm will be issued. (A Contact)
➁ N.C(Normal Close) Sensor : Sensor remains closed all the time and if open, an
alarm will be issued. ( B Contact)
●
Cam
Determines a camera which will synchronize with the current sensor.
The default is currently set to the sensor number. A sensor shall be synchronized
with at least a camera. Multi-synchronization is possible.
Alarm
Sensor
1
2
3
4
5
6
7
8
Alarm-Out
Sensor State Cam
None
N.O
1
Off
CHO3
CHO2
CHO1
Off
CHO6
CHO5
CHO4
Off
CHO8
CHO7
All
Off
OK
Cencel
Off
None
Off
1
Off
0
None
OK
●
Beep-Out
10sec
10sec
10sec
10sec
10sec
10sec
10sec
10sec
Cancel
Alarm-Out
Arranges Alarm-Out when Alarm Sensor sounds.
At this moment, this supports 5 Alarm Outs. Choose an alarm-out that you want to
synchronize with the current sensor. Multi-choice is possible.
●
Beep-Out
Determines Alarm-Out Duration. Alarm-Out continues for the determined duration.
Off/ 3sec/ 5sec/ 10sec/ 20sec/ 30sec/ 1min/ 2min
5-21
Motion Detecting
●
M.D State
Off : Motion Detection does not operate
On : Motion Detection starts operation.
●
Area
Select the Motion Detection zone. It is composed of 45x48 sized Block. You are
forbidden to determine 4 block rows(Up/Down/Left/Right) to allow them to be
displayed in all monitors.
❿ Select All : Selects the whole area.
❿ Select One : Selects a block every time. Selection is done by a toggle system.
❿ Select Quarter : Split the whole area into 4 pieces, which enables selecting a
fourth of the whole area.
❿ Clear All : Cancels the whole area.
❿ Save & Exit : Saves and exits.
❿ Exit : Exits without saving.
5-22
SHR-4080P USER’S MANUAL
●
Sensitivity
Determines Motion sensing sensitivity. Sensitivity grade consists of Low ➝
Medium ➝ Very High in the ascending order.
●
Alarm-Out
Selects Alarm-Out scope when Motion occurs.
At this moment, this supports 5 Alarm Outs. Choose an alarm-out that you want to
synchronize with the current motion channel. Multi-choice is possible.
●
Beep-Out
Determines Alarm-Out Duration. Alarm-Out continues for the determined duration.
Off/ 3sec/ 5sec/ 10sec/ 20sec/ 30sec/ 1min/ 2min
Video Loss
●
Video Loss State
Off : Video Loss does not operate.
On : Video Loss starts operation.
●
Alarm-Out
Selects Alarm-Out scope when the current Video Loss occurs.
At this moment, this supports 5 Alarm Outs. Choose an alarm-out that you want to
synchronize with the current motion channel. Multi-choice is possible.
●
Beep-Out
Determines Alarm-Out Duration. Alarm-Out continues for the determined duration.
Off/ 3sec/ 5sec/ 10sec/ 20sec/ 30sec/ 1min/ 2min
5-23
6
Record Schedule
You may select a time when recording starts automatically.
Selection by the day or by the time is available.
The default is set to “None”.
●
Pressing “CH > “ copies the value of Channel 1 to all the channels.
●
The horizontal axis numbered from 0 to 23 represents the time value.
The vertical axis numbered from S to H represents the day value. (H :Holiday)
Selection by the day or by the time is available.
●
Pressing “ALL” converts the overall setting of the selection window into
Continuous➝Event➝Both➝None.
●
Continuous Recording
Recording starts automatically on the preset time.
Recording follows the condition established in 5-17.Record Mode of MENU.
☛ Refer to 7-3 Record Schedule of MENU.
●
Event Recording
Recording starts automatically when Event occurs to Alarm/Motion Detection/Video
Loss within a designated time.
Recording follows the condition established in 5-18.Event Record Mode Setup of
MENU.
☛ Refer to 7-4 Event Recording of MENU.
5-24
SHR-4080P USER’S MANUAL
●
Both(Continuous, Event)
On occurrence of Event, Continuous Recording is replaced with Event Recording
Mode.
●
Holiday
If you press “Holiday”, a calendar pops up and you are able to designate holidays.
Move to a date and press “Enter” to complete designation.
Press “Enter” once more to cancel designation.
“H” at the bottom of the table means a holiday.
5-25
7
Backup
●
Sel Tap is not checked in the beginning.
Once checked, Sel Tap activates “Start” and free space is displayed in the Free
Space zone.
●
Set the date and time that you want to back up and press “Start” to start Backup.
When you change Start Date/Time or End Date/Time, free space keeps updated in
the Free Space zone.
●
Set to First On, Backup is set to the date of the initial data and the time is inactivated.
●
Set to First Off, Backup cancels Dim so that you can set a date on your own.
●
Set to Last On, Backup is set to the date of the initial data and the time becomes dim.
●
Set to Last Off, Backup cancels Dim so that you can set a date on your own.
●
Without Backup Device, Warning sign pops up.
Select and connect Backup Device in 5-8.HDD Setup of MENU and proceed with
Backup.
●
With more than 2 Backup Devices connected, Warning sign pops up.
More than one Backup Device is prohibited in Backup process.
Backup setup is allowed for either SCSI or IEEE1394 of 5-8.HDD Setup in MENU.
●
Press “Stop” to stop Backup.
●
Pressing Cancel during the Backup returns to the upper menu but this does not
affect Backup process.
Note
[Backup Device]
Without Backup Device or with more than one Backup Device, Backup does not
start. Check if only Backup Device is connected before you proceed with Backup.
Caution
[In Backup Process]
Pressing Cancel returns to the upper menu but this does not affect Backup process.
Press Stop to suspend Backup. Backup may possibly slow the speed of the set.
5-26
SHR-4080P USER’S MANUAL
8
Network
Netwrok
Connection Mode
Bandwidth
Admin Password
User Password
IP(Port)
Gateway
Subnet Mask
DNS
ADSL User ID
Password
●
Static IP
2 Mbps
*************
*************
192.168.001.201(554.555.556.557)
192.168.001.001
255.255.255.000
168.126.063.001
ID
*************
Connection Mode
Designates the kind of the network connected to the main body of SHR-4080P.
Static IP : When the main body is connected to the network with Static IP.
Dynamic IP : When the main body is connected to the network with Dynamic IP
supplied by DHCP.
ADSL(PPPoE) : When the main body is connected to the ADSL network with PPPoE.
●
Bandwidth
Designates the network speed to which the main body of SHR-4080P is connected.
Unlimited / 2 Mbps / 1 Mbps / 600 Kbps / 300 Kbps
Caution
When the main body is connected to the network using high speed LAN, set to 1
Mbps or 2 Mbps. When the main body is connected to the network supporting low
bandwidth such as ADSL, set below 600 Kbps. If you set Bandwidth high though the
main body is connected to a slow network, the network load will get heavy therefore
the connection with Smart Viewer or video monitoring may be instable.
●
Admin Password
The password for the connection between Smart Viewer and the set with the authority
of Admin. The password can be as long as 8 digits.
Press "Enter" and the left number keys from 0 to 9 for setup.
●
User Password
The password for Smart Viewer’s access to the set with the authority of general user.
●
IP (Port)
So sets up the IP Address and Port number as to connect the main body of SHR-4080P
with the network. If the Connection Mode is set to Static IP, you shall type in IP yourself.
If the connection mode is Dynamic IP or ADSL(PPPoE), the IP allocated by the DHCP
server or ADSL company will be automatically displayed. In case of failure of DHCP or
ADSL connection, 000.000.000.000 will be displayed. Then, press OK to retry connection to get a new IP. If you continue to fail in DHCP or ADSL connection, keep the main
body of SHR-4080P off for a while and turn it on for retry. The Port number indicates the
4 ports by which the main body attempts network connection. The default is 554, 555,
556, 557. You may change the Port number under circumstances. The Port number will
be altered in group of 4 consecutive numbers. If you allocate different Port numbers to
each main body and IP Router while you use IP Router to connect multi SHR-4080Ps,
you can compose a network through port forwarding.
5-27
●
Gateway
Determines Gateway Address in the SHR-4080P main body.
●
Subnet Mask
Determines Subnet Mask Address in the SHR-4080P main body.
●
DNS
Sets up DNS Address in the main body of SHR-4080P. The default of DNS is
168.126.63.1. Generally, you don’t have to alter the DNS default but you may be hard to
connect to the network sometimes if you use DHCP or ADSL. In this case, call the network manager or ADSL company to set up a new DNS address.
●
ADSL User ID
If the main body of SHR-4080P is connected with the ADSL(PPPoE) network, input
User ID subscribed to the ADSL company. You may input User ID with a Virtual keyboard as long as 40 digits irrespective of alphabets, numbers, or symbols.
●
Password
If the main body of SHR-4080P is connected to the ADSL(PPPoE) network, input the
user password subscribed to the ADSL company. You may input the password with a
Virtual keyboard as long as 40 digits irrespective of alphabets, numbers, or symbols.
Caution
Be sure to set up IP/Port/SubnetMask/Gateway/DNS to let Smart Viewer connect
with the main body of SHR-4080P.
Wrong IP/Port/Gateway/SubnetMask/DNS may prevent Smart Viewer from being
connected to the main body of SHR-4080P.
Please call the network manager or ADSL company to get each setting value.
Note
If you want to connect IP Router with the main body of SHR-4080P, you shall designate
a port for SHR-4080P in the IP Router setup menu.
The main body of SHR-4080P uses 4 ports for TCP communication.
In addition, if you want to use the DHCP function backed by IP Router to allocate
Dynamic IP to the main body of SHR-4080P, you shall designate a port for the IP which
SHR-4080P has been allocated by the IP Router setup menu.
If you use IP Router, you are recommended to rather determine IP and Port numbers to
be allocated to the main body of SHR-4080P from the IP Router setup menu, set the
connection mode to Static IP for the main body of SHR-4080P, and input the determined IP and Port number in IP Router than use the DHCP function.
Please refer to the IP Router User’s Manual or call the manufacturer to set up IP Router.
Caution
If you set the main body network bandwidth to 300Kbps and enter the ADSL mode
by Viewer, only 4CH monitoring and 1CH search are available but Audio is not.
5-28
Chapter 6
PTZ Camera Control
6
SHR-4080P USER’S MANUAL
1
PTZ Camera Control Mode
●
Select a proper PTZ Device Configuration value in MENU to enter PTZ Control
Mode.
●
Selected in MENU, the symbol(
screen.
●
If you press the Enter( ➛ ) button among direction keys in front of Split Screen,
a blue bar will appear in the monitor screen. Use direction keys to move this bar
until you reach the channel with the PTZ symbol and press the PTZ button in front
of SHR-4080P to enter PTZ Camera Control Mode.
If you succeed in entering PTZ Camera Control Mode, the PTZ symbol on the
monitor screen will turn yellow from white while the PTZ button in front of SHR4080P will turn blue. PTZ Camera Control Mode supports Pan, Tilt, and Zoom
operation.
PTZ
6-1
TELE
PTZ
WIDE
) of PTZ is displayed on the channel in the
VIEW
PRESET
●
Other PTZ Camera Control Modes perform its control in a single screen. Press the
channel selection button in the left front to select the channel whose Menu selected PTZ and then press the PTZ button. If you succeed in entering Single Screen
PTZ Camera Control Mode, the PTZ symbol on the screen will turn yellow from
white while the PTZ button will turn blue. Single Screen PTZ Camera Control
Mode supports Pan, Tilt, and Zoom operation basically and Preset, Camera Menu,
and other functions additionally.
●
Press the PTZ button in Live Mode to cancel PTZ Camera Control Mode. After
cancellation, the PTZ symbol on the screen will turn white from yellow while the
PTZ button will lose its blue light.
Note
If you select Remote Control Device, you may not control PTZ Camera with SHR4080P. It’s because the PTZ button in front of SHR-4080P remains inactivated.
Press the PTZ button and the PTZ ban icon(
) will appear. It’s because the RS485 port setup was done for Romote Control Device.
6-2
SHR-4080P USER’S MANUAL
2
Basic Operation of PAN, TILT, & ZOOM
●
PAN
Press the LEFT or RIGHT button in front SHR-4080P in PTZ Camera Control
Mode to control PTZ Camera horizontally.
PTZ
●
TELE
WIDE
VIEW
PRESET
TILT
Press the UP or DOWN button in front SHR-4080P in PTZ Camera Control Mode
to control PTZ Camera vertically.
PTZ
●
TELE
WIDE
VIEW
PRESET
ZOOM
Press the TELE/WIDE button in front SHR-4080P in PTZ Camera Control Mode to
zoom in or out PTZ Camera.
PTZ
6-3
TELE
WIDE
VIEW
PRESET
3
PRESET Setup
●
Records a certain position of PTZ Camera.
●
Memorizes up to 20 PTZ Camera positions at the moment.
Note
For AD Protocol PTZ Camera, this memorizes only 7 positions.
●
Press the SET button in front of SHR-4080P in Single Screen PTZ Camera Control
Mode to set up Preset.
PTZ
●
TELE
WIDE
VIEW
PRESET
After PRESET setup, press ENTER.
6-4
SHR-4080P USER’S MANUAL
6-5
●
Move the cursor right and press ENTER in PTZ Control Mode first. Then, press
Enter to run P/T/Z/ Motion Mode in the PIP screen and press Enter again to cancel
P/T/Z/ Motion Mode.
●
Press Enter at the Position Name position to see Virtual Keyboard. Type Position
Name and press OK to save Position and Position Name.
●
Press Del to delete both Position and Position Name with the number.
●
Press Del✓ on the top to delete all Positions and Position Names in memory.
4
Camera Menu Setup
●
Camera Menu is a menu supplied by PTZ Camera itself. This Menu sets up several conditions of PTZ Camera.
Note
Either Panasonic or Samsung Protocol Camera only is authorized for Camera Menu
setup.
●
Press the SET button in front of SHR-4080P in Single Screen PTZ Camera Control
Mode to select Camera Menu.
PTZ
●
TELE
WIDE
VIEW
PRESET
Press the SET button in front of SHR-4080P to return to the upper menu from SET
button Camera Menu.
6-6
SHR-4080P USER’S MANUAL
5
Preset View
●
Preset setup allows your movement to a certain saved position of PTZ Camera.
●
Press the VIEW button in front of SHR-4080P in Single Screen PTZ Camera
Control Mode to select Preset.
PTZ
TELE
WIDE
VIEW
PRESET
(For example, Samsung Protocol)
●
6-7
Control the cursor until it reaches a Preset position number that you want to move
to and you can check the right movement through in PIP Screen on your right.
6
Other View
●
Press the VIEW button in front of SHR-4080P in Single Screen PTZ Camera
Control Mode to supply PTZ Camera. This is a very special function.
Note
Samsung, Panasonic, PelcoP, or PelcoD Protocol PTZ Camera supplies this function.
Samsung : Auto Pan / Scan / Pattern
Panasonic : Auto Pan / Sequence / Sort
Pelco(P,D) : Auto Scan / Frame Scan / Pattern
PTZ
Preset
Auto Pan
Scan
Pattern
Samsung
EXIT
TELE
Preset
WIDE
Auto Pan
VIEW
Sequence
Panasonic
Sort
PRESET
EXIT
Preset Auto Scan
Frame Scan
Pattern
EXIT
Pelco
●
After you select a function, press Enter. Then the function will be checked and
start running.
●
If you select other function while this function is in action, the previous function will
be unchecked and the current function will be checked.
(For example, Samsung Protocol)
●
If you put P/T/Z/ in operation or enter Preset Setup or Camera Menu Setup Menu
while this function is in action, the function in action will be suspended and
unchecked.
●
Restart of SHR-4080P System in action has no effect. The function continues its
duty and remains checked.
6-8
Chapter 7 Recording
7
SHR-4080P USER’S MANUAL
1
PANIC (Emergency Recording)
7-1
●
Pressing the button records all the images input so far.
PANIC Recording specification is Normal Size, Level 8 Quality, and 25 ips. During
PANIC Recording, LED lights on and a recording icon appears on the screen.
During recording in HDD, HDD LED in front blinks.
●
During PANIC Recording, you may stop PANIC Recoding by pressing the button
then LED lights out.
2
REC (Normal Recording)
●
Pressing REC the button starts recording as set in Record Mode of MENU. Then,
REC LED lights on and a recording icon appears on the screen. During recording
in HDD, HDD LED in front blinks.
●
During REC Recording, you may stop REC Recoding by pressing the REC button
then REC LED lights out.
●
If you press the REC LOCK button during REC Recording, REC LOCK LED will
light on and the REC button will be locked. Cancel REC LOCK first and press the
REC button to cancel REC.
7-2
SHR-4080P USER’S MANUAL
3
Record Schedule
●
While “Continuous Recording” or “Both” is selected for Record Schedule in MENU,
Timer Recording automatically starts. Otherwise, Timer Recording remains inactivated. During Timer Recording, Recording Icon appear on the screen. During
recording in HDD, HDD LED in front blinks.
●
While Event Recording is selected, recording starts at every event. If it’s the case,
recording will be done according to the Event Record setup of the channel in the
small [ EVENT Record Mode Setup ] elements among [ EVENT RECORD ] items
in MENU.
Note
Even in case of an event, Event Recording will not start unless Event Recording or
Both is selected in Record Schedule.
7-3
4
Event Recording
●
Alarm
Sensor State in Event Record Alarm of MENU shall be set to N.O (Normal Open)
or N.C (Normal Close)
●
Motion Detection
M.D State in Event Record Motion Detection of MENU shall be set to On.
●
Video Loss
Video Loss State in Event Record Video Loss of MENU shall be set to On.
●
Event Record Mode Setup
When Event occurs, it designates recording type. In particular, depending on
PreAlarm Off or PostAlarm Off, PreAlarm or PostAlarm Recording is disabled
respectively.
7-4
Chapter 8
Search and Play
8
SHR-4080P USER’S MANUAL
Before Use
●
Pressing the SEARCH button shows Search Menu on the screen as seen above.
●
CALENDAR uses a calendar to search video files at the preset time.
●
Event Search searches video files recorded by Event.
●
Date/Time inputs a day and time on which the system searches video files.
●
Go To First searches video files from the oldest one.
●
Go To Last searches video files from the latest one.
●
Backup Data Search searches backed-up video files.
Note
During Event Recording, the Search or Play button has no power to let you enter the
Search mode. On entering the Search mode, (
) will appear.
8-1
1
Calendar Search
●
Be sure to designate both the channel and the date first. Then press “Start” to initiate search.
●
Uses a calendar to search video files at the preset time. Four channels as a maximum are in the range of search.
●
Use the ➛ key and ➛,❿ key to select up to 4 channels. Then a date when one
or more selected channels have video files recorded will be displayed in thick blue.
●
Use the ❷ key until you reach the Year/Month setup line and use both the
key and the ➛,❿ key to set up Year/Month.
●
If you choose a day with more than a video file recorded by the ➛
key, a
checkbox will appear on the right of the date number and the checkbox will be
checked.
●
Use the ❷ key until you reach the Time bar and use the ➛
●
If you want to start search, use the ❷ key until you reach [START] and input the
key. If you want to cancel search, use the key until you reach [CANCEL]
➛
and input the ➛ key.
●
The Time bar appears every 30 minutes.
key to set up Time.
8-2
SHR-4080P USER’S MANUAL
2
Event Search
8-3
●
Searches Normal Recording, Panic Recording, Sched.(Schedule) Recording,
Alarm Recording, Motion Recording, and VLoss(Video Loss) Recording by the
time.
●
You shall select a channel to search to see the Event information of the channel.
●
On the basis of the Event information for each channel, the system searches the
video file for the event. Only one channel is allowed for video search.
●
If you use both the ➛ key and the ➛,❿ key to select a channel, the system will
show the list of event for the selected channel only.
●
After channel selection, you may use the , ❷, ➛ key to choose an event out
of the list. The checkbox on the left of the selected event number will be checked.
●
If you want to start search, use the ❷ key until you reach [START] and input the
➛
key. If you want to cancel search, use the key until you reach [EXIT] and
input the ➛ key. If you wish to view the event list of the next screen, choose
[NEXT] and input the ➛ key and if you wish to view the event list of the previous screen, choose [PREV] and input the ➛ key.
3
Date/Time Search
●
Use the Day/Time information to search video files at the time as you desire. Up to
4 channels can be searched at once.
●
After you select a channel with the , ❷, ➛
the selected event number will be checked.
●
Use the ❷key until you reach the Search Time setup line. Input the ➛ key to
change the search time. Search Time change will be done by the
Year/Month/Day/Hour/Minute/ Second unit with the , ❷ key. For your convenience, you may hold on a key to change the value continuously.
●
If you want to start search, use the ❷ key until you reach [START] and input the
➛ key. If you want to cancel search, use the key until you reach [CANCEL]
and input the ➛ key.
●
The time information 2004-03-10 08:38:58 on the bottom left corner represents
the time when play starts.
key, the checkbox on the right of
8-4
SHR-4080P USER’S MANUAL
4
Go to First Search
8-5
●
Searches the oldest one among recorded video files. Up to 4 channels can be
searched at once.
●
After you select a channel with the , ❷, ➛ key, the checkbox on the right of
the selected channel number will be checked.
●
If you want to start search, use the ❷key until you reach [START] and input the
key. If you want to cancel search, use the key until you reach [CANCEL]
➛
and input the ➛ key.
5
Go to Last Search
●
Searches the latest one among recorded video files. Up to 4 channels can be
searched at once.
●
After you select a channel with the , ❷, ➛ key, the checkbox on the right of
the selected channel number will be checked.
●
If you want to start search, use the ❷ key until you reach [START] and input the
key. If you want to cancel search, use the key until you reach [CANCEL]
➛
and input the ➛ key.
●
If you start Go To Last Search during recording, the system will search the video
image right at the time of entering Search.
8-6
SHR-4080P USER’S MANUAL
6
Backup Data Search
8-7
●
Searches a video file for the preset time making use of the Day/Time information
among recorded video files. Up to 4 channels can be searched at once.
●
After you select a channel with the , ❷, ➛ key, the checkbox on the right of
the selected channel number will be checked.
●
Use the ❷key until you reach the Search Time setup line. Input the ➛ key to
change the search time. Search Time change will be done by the
Year/Month/Day/Hour/Minute/ Second unit with the , ❷ key. For your convenience, you may hold on a key to change the value continuously.
●
If you want to start search, use the ❷key until you reach [START] and input the
➛
key. If you want to cancel search, use the key until you reach [CANCEL] and
input ➛ the key.
●
The time information 2004-03-06 17:47:27 on the bottom left corner represents
the time when play starts.
7
Play
●
Press the PLAY/PAUSE button(
●
This chooses out a channel with the oldest data among recorded channels and
plays the data from the first part of the channel. If you used the SEARCH button
for play just before, the system would remember the information of the played
channel until you click the PLAY/PAUSE button( ❿ II ) again, then the system
plays the previous channel.
❿ II
If you press the PLAY/PAUSE button(
as you never tried Play.
) to play the data recorded in HDD.
❿ II
), the Search Menu will appear as far
Note
- Pressing the PLAY button( ❿ II ) does not affect play as far as the user stays in
MENU. Be sure to escape from MENU to start play.
●
■
Press the STOP button(
) to stop play. If you press the Playback/PAUSE
button( ❿ II ), recording will resume from the point where the previous recording
stops. When the data position reaches the end of HDD during play, play will be
paused.
8-8
SHR-4080P USER’S MANUAL
●
Definition Play Screen Mode
4 Split Screen
Single Screen
PIP Screen
9 Split Screen
If you press the Mode key, the play screen will be characterized by 4 Split, Single,
PIP, and 9 Split Screen. If you select one channel in Search, 4 Split Screen will not
appear.
① 4 Split Screen : If you select more than a channel, 4 Split Screen will appear.
➁ Single Screen : This appears when you select one channel in Search. If you
press [ENTER Button] in this screen, a blue bar will appear. Put
the cursor on the channel concerned and press the Mode button
then the selected channel appears in Single Screen. If you press
the ZOOM button, the selected area will be enlarged by twice.
(Refer to 4-6, Zoom Function.)
➂ PIP Screen : If you press the Mode button while Single Screen plays, PIP Screen
will appear(The large screen displays the channel in play while the
small screen on the bottom right corner displays a Live channel in
PIP type). Use the UP and DOWN key to move small PIP
screen(Live Channel) vertically. If you press [ENTER Button], a blue
bar will appear in Live Screen and if you press the Channel button,
you will be able to turn to the channel selected by Live Screen.
➃ 9 Split Screen : If you press the Mode button in PIP Screen, 9 Split Screen (Live
8 channels + Play 1 channel) will appear. Adjust the Menu setup
to relocate Play Screen in the center or on the bottom right corner. Pressing the [Monitoring ➝ PB Channel Position mode
button in MENU proceeds to 4 Split Screen or Single Screen
again.
8-9
●
Play at Faster Speed
If you press the LEFT or RIGHT button( ➛➛ / ❿❿ ) or use the shuttle during
play, you will be able to see the screen at the x2, x4, x8, x16, x32, and x64 speed
either forwardly or reversely.
●
Viewing Still Screen
If you press the LEFT or RIGHT button( ➛➛ / ❿❿ ) or use the jog shuttle with
the system paused, you will be able to see still screens forwardly or reversely.
During reverse search, the interval between cuts varies depending on the recording specification.
●
Audio On/Off
If you press the “0” button in other screen than 4 Split Screen(i.e. Single Screen,
PIP Screen, and 9 Split Screen), you will be able to turn Audio of the channel in
play on or off. In 4 Split Screen, Audio is not activated.
Note
If Event Recording begins activating during Playback, Playback will be paused to
enter the Live mode.
8-10
Chapter 9 Backup
9
SHR-4080P USER’S MANUAL
1
Backup Start
●
To proceed with Backup, an armored HDD(IEEE1394 HDD,SCSI) shall be connected for backup purpose.
① Input the time when Backup will start and end in MENU.
➁ When the file size to be backed up exceeds that of the armored HDD, Backup
does not start.
➂ Pressing START begins backing up the whole channel data until the preset
time at the armored HDD.
➃ During Backup process, Backup LED in front of SHR-4080P turns green.
Note
Pressing Cancel does not cancel or pause Backup but rise to the upper menu. Backup
continues.
9-1
2
Backup STOP
●
If you select Stop during Backup process, Backup will stop immediately.
① As soon as Backup stops or ends, Backup LED in front of SHR-4080P lights out.
➁ If you change the time of the system or shuts down it, Backup in progress will
stop.
9-2
SHR-4080P USER’S MANUAL
3
Backup Play
●
Press the SEARCH button in front of SHR-4080P and select Backup Search to
play the backup data.
●
Select a channel and time and press Start to play a data.
Note
Backup is not available during Backup
Refer to 8-7 Backup Search of User’s Manual.
9-3
Chapter 10
Smart Viewer
10
SHR-4080P USER’S MANUAL
1
Introduction
Smart Viewer is a program that a general PC user is able to install SHR-4080P to his
PC to monitor the search video and audio data through Network without going to the
site where SHR-4080P is installed by himself.
10-1
2
Feature
●
Thanks to the transmission of video data compressed by the MPEG-4 Video
Compression method, this plays video images of good quality.
●
Thanks to the G.726 Voice Compression method, this supplies voice data of good
quality. Use of armored MIC improves the quality of remote voice.
●
Thanks to the transmission of video/audio stream through RTP(Real-Time
Transport Protocol), real-time video play capacity is excellent and multi-users’
simultaneous connection does not affect the transmission speed in whole abruptly.
●
Command & Control by RTSP(Real-Time Streaming Protocol) enables safety control through Network.
●
Connection is open to you at any time to monitor video and audio data by inputting
IP Address only.
●
You can not only perform real-time recording(*.dvr format) whereas necessary during monitoring but also convert recorded video files(*.dvr format) into frame unit
images((JPEG format).
●
Up to 3 Smart Viewer users are allowed to connect to a DVR simultaneously. (One
Admin user and 2 general users)
●
With a Smart Viewer, you are allowed to connect to as many as 4 SHR-4080Ps to
monitor them simultaneously.
●
Smart Viewer is optimized in the resolution of 1024X768
10-2
SHR-4080P USER’S MANUAL
3
PC Specification(Recommendation)
●
OS : Win98SE, WinMe, Win2000, WinXP
●
Recommendation :
CPU P3 1GHz or higher
RAM 256 Mb or higher
VGA RAM 16Mb or higher
DirectX 8.1 or higher
Note
Depending on Recording Rate, Video Size, and user’s PC specification set to SHR4080P, the number of Smart Viewer play frame varies.
For the detailed specification, refer to Appendix 5.
10-3
4
Smart Viewer Installation
10-4-1 Smart Viewer Installation
●
Put a Smart Viewer Program CD in CD-ROM and open the “Smart Viewer” folder
in CD.
●
Smart Viewer supports Win98se/ME/2000/XP OS. Win98se/ME users and
Win2000/XP users shall make use of the setup file in the “Win98_ME” folder and
the “Win2000_XP ” folder respectively.
●
Run the “Setup.exe” file.
10-4
SHR-4080P USER’S MANUAL
10-5
●
Click the “Next” button.
●
If you agree with Smart Viewer License, click “Yes”.
●
Designate a folder to install Smart Viewer in it and click “Next”.
●
The system proceeds with setup file installation and system setup.
●
Installation is complete. Press “Finish” to terminate installation.
10-6
SHR-4080P USER’S MANUAL
10-4-2. Smart Viewer SDK Setup
Smart Viewer SDK is a tool to help a user make his own Viewer program with the
modules(ActiveX Control, DirectShow Filter) for the operation of Smart Viewer in the
MS Windows environment.
If you execute the Smart Viewer SDK installation program, the modules used for
Smart Viewer, documents about the sample code supplied for the realization of API
and Viewer Program, and sample programs will be installed in each folder.
10-7
●
Open the "Smart Viewer SDK" folder in the Smart Viewer Program CD.
●
Run "Setup.exe".
●
Click "Next".
●
If you agree with Smart Viewer SDK License, click "Yes".
10-8
SHR-4080P USER’S MANUAL
10-9
●
Designate a folder for Smart Viewer SDK installation and click "Next".
●
Install the SDK document and sample program and set up the necessary system.
●
Installation Complete. Click "Finish" to terminate the installation.
Note
Refer to the Doc folder in the folder in which Smart Viewer SDK has been installed
for the details of Smart Viewer SDK.
10-10
SHR-4080P USER’S MANUAL
5
Smart Viewer Program Execution
●
10-11
Double-click the Smart Viewer icon in the background screen to run the program.
6
Smart Viewer Initial Screen
●
Screen Description
2
1
3
4
5
6
7
8
9
10
11
! Pressing this button enters Search Mode in which you can search and play the
video data recorded both in Monitoring Mode for real-time video data monitoring
and in SHR-4080P.
@ This button terminates or minimizes the program.
# It displays the current date, day, and time.
$ This button is used for the connection with the preset DVR(SHR-4080P) or site.
% This screen shows the monitoring video image.
^ This window displays the event message from SHR-4080P real-time.
& This button displays the current channel status in hand or selects/converts channels.
* This button adjusts Audio Volume and Video Brightness/Contrast or records video
data.
( This button is used for PTZ related functions.
) This button is used for screen split and Sequence Mode.
1 This button puts up the Setup Mode window to change Smart Viewer or
SHR-4080P setup. (Refer to 10-9. Setup Mode.)
10-12
SHR-4080P USER’S MANUAL
7
Monitoring Mode
●
DVR(SHR-4080P)/SITE Connection
- Select the name of DVR(SHR-4080P) or site for connection and click the connection button.
Note
You can determine the name, IP, and password of DVR(SHR-4080P) for connection
in Setup Mode. Also, setup of a site which permits simultaneous connection to multiDVRs(SHR-4080P) is available in Setup Mode.
You are allowed for the simultaneous connection with no more than 4 DVR(SHR4080P)s as you approaches at the site.
Connection Failure Cases
1. Password Certification Failure
- In case of discord between the Network password set to SHR-4080P and the
connection password set to Smart Viewer, a window pops up to induce retry of
password input.
2. Admin User Connection Failure
- Where SHR-4080P that you wish to connect to has been already occupied by
other user in an Admin. Capacity, you are authorized with access to SHR-4080P
concerned in a User capacity.
10-13
Note
No more than 3 users, one Admin. authorized user and 2 User authorized users are
allowed to access SHR-4080P simultaneously.
Caution
Once occupied by 3 users, SHR-4080P does not permit more connection.
●
Monitoring Mode Connection Screen
Caution
If you alter “Resolution” or “Color Quality” from the setup tab of [Display
Registration Information] while Smart Viewer is running, Smart Viewer will fall into
an unexpected condition.
You shall terminate Smart Viewer first to recover the condition.
●
Mode Conversion Button
- This button changes Monitoring Mode or Search Mode.
- Mode change is authorized with you only when connected as an Admin. authorized user.
10-14
SHR-4080P USER’S MANUAL
●
Time Information
- As soon as you are connected to SHR-4080P, the current date, day, and time of
SHR-4080P will be displayed.
- Otherwise, the current date, day, and time of your PC will be displayed.
●
Connection Information
- As soon as you are connected to SHR-4080P, the connection button will display
connection status.
- If you click the connection button here, connection will be cancelled.
●
Play Screen OSD Information
2
1
4
5
3
6
! Channel no., camera name, and video size will be displayed.
Video Size (N) Normal/(S) Small/(L) Large
@ The Video data of the current channel are recorded in your PC with REC mark
displayed.
# Audio ON/OFF Button is marked.
$ The name and IP address of SHR-4080P in connection are displayed.
% The current channel alarm status is displayed.
^ Possibility of the current channel PTZ controllability is displayed.
10-15
Note
# Clicking the speaker icon turns Audio of a channel on or off.
: Audio OFF
: Audio ON
If you turn Audio of a SHR-4080P channel off, Disable will be displayed.
: Audio Disabled
✴ You can turn Audio on for one channel only.
✴ For the channel with Audio turned on now, use the following Audio relate button
Note
% Where Alarm or Motion Detection occurs at a channel of SHR-4080P with Alarm
or Motion Detection established, an icon pops up on the screen real-time.
: Motion Detection
: Alarm Event
Note
In case of Motion or Alarm Detection Event, SmartViewer will show the important
images again before or after the event.
Meanwhile the time of image created by the event will be displayed on Video
Window.
Note
^ If you connect and set up PTZ Camera in SHR-4080P, PTZ controllability of the
channel will be displayed.
✴ Select a channel capable of PTZ and use the PTZ related buttons at the bottom to
control PTZ. (Refer to the description of PTZ Related Button.)
10-16
SHR-4080P USER’S MANUAL
●
Event Log Display Window
- Displays the event(alarm, user connection, and setup change) occurring at
SHR-4080P real time.
Note
[Event Message]
❿ Connecting.. : Trying to connect to SHR-4080P.
❿ Connected.. : Succeeded connecting to SHR-4080P.
❿ Connection Failed : Failed in connecting to SHR-4080P.
❿ Disconnected.. : Finished connecting to SHR-4080P.
❿ Setup(Remote) : SHR-4080P at Dvr Setup of Viewer changed.
❿ Setup Start / End (Local) : Start/Finish the Menu screen at SHR-4080P.
❿ Video Loss CH[N] : Video Loss at the N channel of SHR-4080P encountered.
❿ Alarm Detection CH[N] : Alarm issued at the N channel of SHR-4080P.
❿ Motion Detection CH[N] : Motion detected at the N channel of SHR-4080P.
❿ Time Change : Date/Time of SHR-4080P changed.
❿ Load Factory Default : SHR-4080P System initialized.
❿ Network Change : SHR-4080P Network setup changed.
❿ System Shutdown : SHR-4080P System terminated.
❿ Hdd Format : SHR-4080P HDD initialized.
❿ Disk Full : No more space in SHR-4080P HDD.
❿ Power Failure Recovery : SHR-4080P resumed after power failure.
❿ Backup Start/End/Fail/Stop : Backup at SHR-4080P started/finished/failed/stopped.
10-17
Caution
When Time Change, Load Factory Default, Network Change, System Shutdown, or
Hdd Format event occurs, Smart Viewer terminates automatically.
●
Screen Split Selection Button
- Small Sized Single / Single / Quad / Nine-Split Mode
- You may change the Split Mode of the screen under monitoring.
●
Sequence Mode Button
- Changes the channel to be played at the preset interval.
- The sequence time interval setup follows the procedure of Setup Mode ➝ Viewer
Setup.
- In Single Mode : 1 ➝ 2 ➝ 3 ➝ 4 ➝ 5 ➝ 6 ➝ 7 ➝ 8 ➝ 1 (CH)
- In Quad Mode : 1,2,3,4➝ 5,6,7,8 ➝ 1,2,3,4 (CH)
- In the event of connection with one SHR-4080P, this will not apply for Nine-Split
Mode.
Note
If you connected with multi-DVRs(SHR-4080P) through a site, Sequence will operate
as follows.
- In Single Mode : DVR1:1CH ➝...➝ DVR1:8CH ➝ DVR2:1CH ➝...➝ DVR1:1CH
- In Quad Mode : DVR1:1,2,3,4CH ➝...➝ DVR2:1,2,3,4CH ➝...➝ DVR1:1,2,3,4CH
- In Nine-Split Mode : DVR1:1,2,3,4,5,6,7,8CH ➝ DVR2:1,2,3,4,5,6,7,8CH ➝...
10-18
SHR-4080P USER’S MANUAL
●
Play Screen Condition Information / Selection Button
- Displays the Split or Play condition of the screen in play.
- Press each camera icon to choose the relative channel.
: During play in Nine-split Mode
: During play in Quad Mode
: During play in Single Mode
10-19
: Camera Off
●
NEXT Button
- Click NEXT(Mouse Left Button) to see the channel next to the current channel.
- In Single Mode : 1 ➝ 2 ➝ 3 ➝ 4 ➝ 5 ➝ 6 ➝ 7 ➝ 8 ➝ 1 (CH)
- In Quad Mode : 1,2,3,4 ➝ 5,6,7,8 ➝ 1,2,3,4 (CH)
- In the event of connection with one SHR-4080P, this will not apply for Nine-split
Mode.
Note
If you connected with multi-DVRs(SHR-4080P) through a site, Sequence will operate
as follows.
- In Single Mode : DVR1:1CH ➝...➝ DVR1:8CH ➝ DVR2:1CH ➝...➝ DVR1:1CH
- In Quad Mode : DVR1:1,2,3,4CH ➝...➝ DVR2:1,2,3,4CH ➝...➝DVR1:1,2,3,4CH
- In Nine-split Mode : DVR1:1,2,3,4,5,6,7,8CH ➝ DVR2:1,2,3,4,5,6,7,8CH➝...
- Press the NEXT button(Right Button) to display the current DVR list.
- Click a DVR in the list to change the DVR in monitoring.
10-20
SHR-4080P USER’S MANUAL
●
Video Recording Button
- If you select a channel in play and click the REC button, the image will be saved
in a file format with the extension of *.dvr in a designated folder of your PC.
- The name of the directory in which an image will be saved, the file name, and the
image save length shall be set up by Setup Mode ➝ Viewer Setup.
- The length of an image to be saved ranges from one minute to 10 minutes.
- The saved image can be played in Local Mode of Search Mode.
- Click the button again to stop recording. However, manual suspension is prohibited for 10 seconds after recording started.
●
Audio Volume Control Button
- You may control Audio volume of the channel in play or set up Mute for it.
- You can increase or decrease Audio volume by 1 between 0 and +10.
●
Video Brightness/Contrast Control Button
- Select the channel in play and use the control button(+,–) to adjust brightness or
contrast of the image.
- The default is set to +5.
- You can increase or decrease brightness or contrast by 1 between 0 and +10.
Press the Button to recover the default.
Note
The adjusted Audio volume, brightness, and contrast values will be saved in your PC
and remain unchanged even if you terminate Smart Viewer and restart it.
* OS of Windows 98 or ME do not support this Brightness/Contrast function.
10-21
●
PTZ Camera Control Buttons
- Select a channel connected to PTZ Camera to control PTZ related functions.
- PAN Left / Right
- TILT Up / Down
- Diagonal Control
- The channel under PTZ control will be displayed in the center of the button.
3
1
2
!@ ZOOM IN / OUT
# POWER ZOOM : Click P to activate POWER ZOOM.
- POWER ZOOM is a function to enlarge or reduce a video screen by touching the
screen itself.
- After POWER ZOOM is dominant, ZOOM IN / OUT will zoom in or out the video
screen.
- POWER ZOOM Operation Procedure : Click POWER ZOOM ➝ Select ZOOM IN or
OUT ➝ Click ZOOM IN or OUT in the video screen ➝ ZOOM IN / OUT will be activated in the clicked part.
Note
The PAN / TILT / ZOOM function is supplied to all camera.
But, POWER ZOOM is supported only by Samsung Smart Dome Camera, with TILT
below 45°.
1
2
3
4
10-22
SHR-4080P USER’S MANUAL
! PRESET
- If you press the PRESET button, a window for PRESET setup pops up.
a If you click the current PRESET number and
a
name, the camera will move accordingly.
b
b You can delete the selected or all PRESET
setup values.
c
c You can set up a new PRESET number and
name.
Note
! The PRESET function is supplied to all camera.
You are allowed to set up no more than 20 PRESET items.
But, the AD Protocol camera supports up to 7 PRESET items.
@ AUTOPAN : The camera executes this function, reciprocating between Start and End.
# SCAN : The camera executes this function, circulating the PRESET setup positions.
$ PATTERN : The camera executes this function, following user defined route.
Note
The name of @,#, and $ functions varies depending on the camera and some cameras does not support any of those functions.
- The Samsung camera supports all the functions and names.
- The Panasonic camera supports all the functions, but with different names.
@ SEQUENCE # AUTOPAN $ SORT
- The PELCO camera supports all the functions, but with different names.
@ FRAME SCAN # AUTO SCAN $ PATTERN
- Other cameras do not support the @AUTOPAN, #SCAN, and $PATTERN
functions.
10-23
●
Self Menu Setup of PTZ Camera
1
! You may set up the Function Menu in PTZ Camera.
1
2
3
! This is a Menu screen supplied by the camera itself, seen from Viewer.
@ Use the / / / button for the movement between menus.
# This is a button for the role of Enter.
Note
The Camera Menu Setup function is supported by Samsung and Panasonic.
Caution
As far as SHR-4080P uses the PTZ Camera control related functions, Smart Viewer
can not control PTZ Camera.
The PTZ Camera control related functions are authorized with the user with Admin
authority.
10-24
SHR-4080P USER’S MANUAL
8
Search Mode
●
Description of Search Mode Initial Screen
- Search Mode is divided into Remote Mode for SHR-4080P image search/play
and Local Mode to play *.dvr file saved in the directory designated by your PC.
1
3
4
2
5
6
7
8
10
9
11
! Pressing this button enters Search Mode for the remote control of the image
recorded in SHR-4080P.
@ This screen shows images in play.
# Pressing this button enters Remote Mode to transmit the image recorded in SHR4080P through network.
$ Pressing this button enters Local Mode for the play of *.dvr files recorded in your PC.
% This windows supplies a calendar to choose “Year/Month/Day” for search.
^ This button controls Audio volume and Video brightness/contrast.
& This button changes screen split.
* Pressing these buttons execute the Record / Convert File / Print / Setup functions.
( This control button plays the searched images.
) Pressing these buttons change channels and DVRs or renew the calendar window and Time Line.
1 This timeline displays the time information on the searched date recorded in
SHR-4080P.
Note
Connected as a general user or to a site, you are denied for access Search Mode.
10-25
●
DVR(SHR-4080P)/SITE Connection
- Same as “DVR(SHR-4080P)/SITE Connection” of Monitoring Mode.
●
Remote Mode
- This mode sends out the video data recorded in SHR-4080P to Network for play.
- Up to 4 channels are allowed for simultaneous search and play.
- The video information at the time indicated by TimeBar will be displayed in the
Play screen.
Clicking enters Remote Mode.
10-26
SHR-4080P USER’S MANUAL
●
Calendar Window
- If the video data in on-line SHR-4080P was recorded, the date turns red.
- If you click the date in red, the saved video data will be displayed.
- The currently selected date will be marked with a thick red box.
- ➛ : Clicking moves to the previous month.
- ❿ : Clicking moves to the next month.
●
Audio Volume Control, Video Brightness/Contrast Control Buttons
- Same as the control function of Monitoring Mode
- Windows 98 or ME do not support this Brightness/Contrast function.
●
Screen Split Selection Button
- Small Sized Single / Single / Quad Mode
Note
In Remote Mode, Nine-split Mode is not available and in Local Mode, Quad, Ninesplit Mode is not available.
10-27
●
Video Record / Convert File / Print / Setup
1
2
3
4
! Video Record Button
- If you select a channel in play and click the SAVE button, the image will be
saved in a file format with the extension of *.dvr in a designated folder of your
PC.
- The name of the directory in which an image will be saved, the file name, and
the length of an image to be saved shall be set up by Setup Mode
Viewer
Setup.
- The length of an image to be saved ranges from one minute to 10 minutes.
- The saved image can be played in Local Mode of Search Mode.
- Click the button again to stop recording. However, manual suspension is
prohibited for 10 seconds after recording started.
Note
Video data recording in Remote Mode is available only when the Play/Reverse
Play/Fast Forward/Fast Backward button remains pressed down.
@ Convert File Button
- This function converts *. dvr files into “*.jpg” files.
10-28
SHR-4080P USER’S MANUAL
# Print
- This function outputs the screen zone of the image in play which is now being
displayed.
$ Setup Mode Button
- This button pops up the Setup Mode window.
●
Play Buttons
2
1
5
9
3
7
4
6
8
! Play : Play
@ Reverse Play : Reverse Play
# Stop : Stop
$ Fast Forward : Fast Play
% Fast Backward : Fast Reverse Play
^ Step Forward : Play of one image per second.
& Step Backward : Reverse play of one image per second.
* Go to First : Play of the first image in Time Line
( Go to Last : Play of the latest(last) image in Time Line
10-29
Note
During play(Play/RevPlay/FF/FB), disconnection or entering both Monitoring Mode
and Local Mode is not permitted. Click the Stop button first before conversion.
●
Time Line
- Displays the time information on the video data in SHR-4080P on the calendar
window for the selected day.
- The General mode indicates the information on time for 24 hours while the
Extension mode indicates the information on time every 2 hours.
2
1
3
[ General Mode ]
! The channels being displayed in Play Screen will be activated in a white background.
@ Time Line : The time information on the video data recorded in SHR-4080P.
# Time Bar : Displays the current time of the video image being displayed in Play Screen.
Note
Double-clicking the neighborhood of Time Bar enters Zoom In Mode.
One column of Time Line represents an hour.
Time Line turns Green(Normal), Red(Panic), Orange(Alarm), Blue(Motion),
Yellow(Schedule), or Purple(Video Loss) depending on the recording condition.
1
2
[ Zoom In Mode ]
! Displays the time line one hour ago.
@ Displays the time line one hour later.
Note
Double-clicking the neighborhood of Time Bar again enters General Mode.
One column of Time Line represents 5 minutes.
Time Line turns Green(Normal), Red(Panic), Orange(Alarm), Blue(Motion),
Yellow(Schedule), or Purple(Video Loss) depending on the recording condition.
10-30
SHR-4080P USER’S MANUAL
●
Next Button
- Changes a channel as the Next button does in Monitoring Mode.
Note
During Video play(Play/RevPlay/FF/FB), channel change is not available.
●
Reload Button
- Clicking updates the time information on the video data recorded in the calendar
window and Time Line.
●
Local Mode
- This mode plays *.dvr files recorded in the directory of your PC by the Record
function.
- You can search and play only one channel.
- You are free for access to the user being connected to SHR-4080P
- Other functions than the calendar display function are as same as those of
Remote Mode.
- The time information on Local File will be displayed at the first channel position in
Time Line together with the file name.
: Clicking selects a file to be played in the file selection window and
enters Local Mode.
Note
Only the *.dvr files saved by Audio activation can be played in Local Mode.
10-31
9
SETUP MODE
●
Description of Initial Screen
3
1
2
4
! This button is used to select items for DVR Setup, Viewer Setup, Site Setup, and
S/W Version setup.
@ Shows what the selected Setup item can set up in detail.
# This button terminates the Setup window.
$ This button saves the information revised in the Setup window, remarks the information prior to such a revision, or terminates the Setup window.
10-32
SHR-4080P USER’S MANUAL
●
Setup Item Selection Button
- This button is used for the selection of each Setup item.
- This is composed of 4 items, DVR Setup, Viewer Setup, Site Setup, and S/W
Version.
- DVR Setup: DVR Setup allows you to change the remote Menu setup items of
SHR-4080P.
- Viewer Setup: Viewer Setup allows you to set up various kinds of items concerning operations of Smart Viewer.
- Site Setup: Site Setup allows you to set up SHR-4080P information, that is SHR4080P name, IP Address, ID, and Password that you contact through Smart
Viewer or register all the registered SHR-4080Ps at a site for control.
- S/W Version: S/W Version shows the current version of Smart Viewer, system
requirement, and the System S/W version of on-line SHR-4080P and upgrades
SHR-4080P System S/W remotely.
●
Save/Cancellation of Revised Information
- Click the [Apply] button to save the information revised in the Setup window click
the [Cancel] button to display the information before such a revision.
●
Closing Setup Window
- Click the [X] icon on the top right corner of the Setup window or the [Close]
button to close the Setup window.
- If more than one Setup item have been revised before you close the Setup
window, the following message box pops up. If you press OK, the revised
information will be saved, closing the Setup window but if you press CANCEL,
the revised information will be flown away, closing the Setup window.
10-33
DVR Setup
- Click the [DVR Setup] button for DVR Setup.
- You can change the setup items of SHR-4080P Menu, being connected with
Smart Viewer remotely.
- DVR Setup is composed of 5 items, System, Camera/Audio, Monitoring,
Recording, and Network.
Note
- DVR setup Where SHR-4080P that you wish to connect to has been already occupied by other user in an Admin Capacity,
- You are authorized with access to DVR Setup in an Admin capacity only. The button
will not be activated if you are connected to SHR-4080P as a user or unconnected.
1
2
! Among more than one on-line SHR-4080P, the name of SHR-4080P connected in
the Admin capacity will be listed. Depending on you are connected to a SHR4080P or the site, the name of SHR-4080P or the name of SHR-4080P connected
in the Admin. capacity among those composing the site will be listed. You may
choose one to set up SHR-4080P Menu.
@ The setup menu for selected SHR-4080P will be displayed.
10-34
SHR-4080P USER’S MANUAL
●
Detailed DVR Setup Items
! System
- Information
Information shows the information on on-line SHR-4080P.
Note
For the detailed items of DVR Setup, refer to Chapter 5, MENU.
- Password
Password determines the password for the control of SHR-4080P Menu or
SHR-4080P key input.
10-35
Caution
System Password shall be composed of number only, up to 8 digits.
Note
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not
supplied to System Password input.
- Use the BACKSPACE key to delete content.
Note
Default System Password is set to 4321.
- Time/Date
Time/Date is used to set up the information on Date, Time, Form, and Summer
Time of on-line SHR-4080P.
Note
- If you change the Time / Date value, SHR-4080P will automatically cut the connection with Smart Viewer to apply a new time setup.
- Upon completion of new time setup of SHR-4080P, you are permitted to resume
connection with Smart Viewer.
- But, Display Format or Summer Time can be set up without disconnection.
10-36
SHR-4080P USER’S MANUAL
- Language
Language sets up the language in which on-line SHR-4080P will be expressed
Note
Language change by SYSTEM LANGUAGE results in change of language expression
setup of SHR-4080P. In short, the language setup of Smart Viewer does not change.
Language specification to be supported is subject to change later.
- Disk Mode
In Disk Mode, you may set up Writing Mode of HDD attached to SHR-4080P.
10-37
- Remocon (Remote Control Device)
Remocon can set up Remote Control Device fixed to SHR-4080P.
Note
If you fix Remote Control Device to the main body of SHR-4080P and activate the
setting values, Viewer will be disabled to control PTZ.
10-38
SHR-4080P USER’S MANUAL
@ Camera/Audio
- Config.
Config. sets up Video, Audio On/Off, Camera Title, and Auto Sequence Time
for each channel of on-line SHR-4080P.
Caution
- Title supports English only. If you type in and apply Title in your native language,
Warning message will pop up to ask your retyping.
- Title shall be composed of no more than 15 texts.
- If you leave Title blank and apply it, Warning message will pop up to ask your
retyping.
Note
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not
supplied to Title input.
- Use the BACKSPACE key to delete content.
10-39
- PTZ device
If a dome camera is connected to all channels, sets up Camera ID, Protocol,
Baud Rate, Parity, Data Bit, Stop Bit, and Serial Mode.
# Monitoring
- Monitoring
Monitoring sets up both Event Monitoring and OSG Display of Live Mode.
10-40
SHR-4080P USER’S MANUAL
$ Recording
- Rec. Mode
Rec. Mode sets up Live Mode decision, Video Size during recording, Quality,
and Rate.
Note
Full D1(L) Video Size does not support 25ips Rate.
- Event Rec.
Event Rec. sets up Video Size, Quality, Rate, Pre Alarm, and Post Alarm
values to be recorded when Event occurs.
Note
Full D1(L) Video Size does not support 25ips Rate.
10-41
- Alarm Rec.
Alarm Rec. sets up the information necessary for Alarm Recording.
Note
More than one camera shall be selected to apply Alarm.
- Motion Rec.
Motion Rec. sets up the information necessary for recording by Motion
Detection.
10-42
SHR-4080P USER’S MANUAL
- Video Loss
Video Loss sets up the information on how to inform the user of Video Loss of
SHR-4080P.
% Network
- Password
This sets up the password for Admin and User to let you connect with SHR4080P through Network in Smart Viewer.
10-43
Caution
- Network Password shall be composed of no more than 8 texts.
- If you leave Password blank and apply it, Warning message will pop up to ask your
retyping.
Note
- The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not
supplied to Network Password input.
- Use the BACKSPACE key to delete content.
Note
- Default Admin Password is set to 654321.
- Default User Password is set to 654321.
- Configuration
Sets up the network connection method of SHR-4080P.
SHR-4080P supports the connection with Static IP, Dynamic IP, and ADSL(PPPoE).
Sets up the network Bandwidth. Please adjust the bandwidth to the network con
dition in which SHR-4080P is connected. Sets up IP Address, Port Number,
Gateway, Subnet Mask, and DNS. Please input both ID and password of the sub
scriber in the event of ADSL.
Caution
- Be sure to inquire the network manager before you input Network IP, Gateway,
Subnet Mask, or DNS.
- Both ADSL ID and Password can be input in alphabets, numbers, and symbols without discrimination as long as 40 digits and 40 digits respectively.
10-44
SHR-4080P USER’S MANUAL
Note
- SHR-4080P uses 4 PORTs for TCP connection.
- A PORT number is flexible and 4 numbers in a row will be changed in all.
(554,555,556,557 --> 558,559,560,561)
- You shall allocate the above ports for SHR-4080P if you want to compose a network by IP Router.
Viewer Setup
- Click the [Viewer Setup] for Viewer Setup.
- Viewer Setup sets up various kinds of items related to Smart Viewer motions.
- Viewer Setup is composed of 5 items, Video Recording, File Converting,
Sequence Time, OSD Display, and Auto Connection.
1
2
3
4
5
! This is used for the setup of information necessary for saving the video data in
display in *.dvr file format while you are connected to SHR-4080P.
@ This is used for the setup of information necessary for converting the file saved
in your PC in *.dvr file format into JPEG.
# This is used for the setup of information necessary for Auto Sequence Mode.
$ This is used for the setup of information on OSD display for Smart Viewer.
% This determines whether Smart Viewer shall be automatically connected to
DVR(SHR-4080P) or Site when it begins running.
10-45
●
Video Recording
! Naming
- Being connected to SHR-4080P in Monitoring or Search Mode, you can save the
video data in display in *.dvr file format. This determines how to name *.dvr file
format.
- The file name depends on camera number and serial number, set to “Camera
No. + Serial No.” or camera number, current date, and time, set to “Camera No.
+ Date”.
@ Location
- As long as you are connected to SHR-4080P in Monitoring or Search Mode while
recording the video data in display, this sets up a directory where *.dvr file format
will be saved.
- The current default directory is “Smart Viewer Program Installed Directory
\video\dvr”.
# Recording Time
- As long as you are connected to SHR-4080P in Monitoring or Search Mode while
recording the video data in display, this sets up the longest recording time.
- Time setup ranges from 1 to 10 minutes. If recording exceeds the preset time at
Recording Time, recording will be automatically stopped.
●
File Converting
[JPEG]
! Location
- You can convert the files saved in your PC in *.dvr file format into JPEG format
files then the frames composing *.dvr file format will be converted into JPEG
format files. Now, this designates a directory in which the converted JPEG files
will be saved.
- The current default directory is “Smart Viewer Program Installed Directory
\frame”.
10-46
SHR-4080P USER’S MANUAL
@ Rate
- When you convert *.dvr file formatted files into JPEG formatted files, this determines how many frames per a second will be converted for recording.
- Setup ranges from 1 frame to 25 frames. But, the maximum number of frames for
setup may be subject to the Record Rate setup in SHR-4080 Menu. In short, if
Record Rate is set to 6 ips in the Menu, Viewer will be able to record up to 6
frames per a second.
●
Sequence Time
- As long as you are connected to SHR-4080P in Monitoring Mode while Auto
Sequence is dominant, this sets up Auto Sequence Time. Time setup ranges
from 10 to 20 minutes.
●
OSD Display
- Determines if OSD shall be displayed on each channel of Smart Viewer.
- Whether you check “Enable” or not, OSD will appear or not. However, Audio
icon, PTZ icon, REC icon, and Alarm/Motion event icon will not be affected by the
OSD Display condition.
10-47
●
Auto Connection
- Determines if Smart Viewer shall be automatically connected to SHR-4080P or
Site as soon as it starts running.
- If you check “Auto Connection On”, the name of SHR-4080P and Sites that are
currently registered in DVR/Site List will be listed as follows and if you select one,
it will be automatically connected to the selected SHR-4080P or Site as soon as
Smart Viewer starts running.
Site Setup
- Click the [Site Setup] button for Site Setup.
- Site Setup sets up the information on DVR(SHR-4080P) or Site that you want to
contact by Smart Viewer.
- Smart Viewer allows you to contact DVR(SHR-4080P) or Site registered here.
1
3
5
2
4
10-48
SHR-4080P USER’S MANUAL
! User registered DVR(SHR-4080P) list will be displayed here.
@ This button adds a new DVR(SHR-4080P) or deletes or revises the alreadyregistered DVR(SHR-4080P).
# User registered Site list will be displayed here.
$ This button adds a new site or deletes or revises the already-registered Site.
% This button adds DVR(SHR-4080P) selected from DVR List to the Site selected
from Site List. But, if the selected DVR(SHR-4080P) is set to ADSL Network, it
can not be registered with the site.
●
DVR List
- DVR List sets up the information on DVR(SHR-4080P) that you want to contact
by Smart Viewer.
- You may register a new DVR(SHR-4080P) or delete and edit the DVR(SHR4080P) selected from the registered list and the name and IP / MAC Address of
the registered DVR will be enlisted in DVR List.
10-49
! Adding New DVR(SHR-4080P)
- If you press the [New] button, the following window will pop up where you are
able to add DVR(SHR-4080P) information.
1. Network Modes - LAN
- If DVR(SHR-4080P) is connected to LAN, set Network Modes to LAN.
- If the LAN connected to DVR(SHR-4080P) uses Static IP, select Static IP from
Address Type and input the name and IP Address of DVR(SHR-4080P).
- You shall select PORTs in accordance with the PORT number determined by
the DVR(SHR-4080P) network menu.
- If Dynamic IP has been allocated to the LAN connected to DVR(SHR-4080P)
through DHCP, select DHCP from Address Type and input the DVR(SHR4080P) name and DVR(SHR-4080P) MAC Address.
- You shall select PORTs in accordance with the PORT number determined by
the DVR(SHR-4080P) network menu.
2. Network Modes - ADSL
- If DVR(SHR-4080P) is connected to ADSL, set Network Modes to ADSL.
- If the LAN connected to DVR(SHR-4080P) uses Static IP, select Static IP from
Address Type and input the name and IP Address of DVR(SHR-4080P).
- You shall select PORTs in accordance with the PORT number determined by
the DVR(SHR-4080P) network menu.
10-50
SHR-4080P USER’S MANUAL
- If Dynamic IP has been allocated to the ADSL connected to DVR(SHR-4080P)
through DHCP or PPPoE, select DHCP/PPPoE from Address Type and input
the DVR(SHR-4080P) name and DVR(SHR-4080P) MAC Address.
- You shall select PORTs in accordance with the PORT number determined by
the DVR(SHR-4080P) network menu.
Reference
- DVR may be named in both English and Korean with no more than 10 texts.
- Login Password shall be as same as Network Password for SHR-4080P to authorize
connection.
- DVR addition will be possible only after you type in all the information where necessary.
Reference
DVR MAC Address is written in the side label of the product.
It is also found in System Information of DVR Menu.
Reference
10-51
- If DVR(SHR-4080P) is connected to ADSL, the network bandwidth is low.
Therefore, the transmission speed becomes low and Viewer operates in the more
limited range.
- Viewer can monitor up to 4CH simultaneously.
- Viewer can search or replay only 1CH.
- Audio replay is unavailable.
- The average number of replay frame is 0.5 ips but flexible depending on the number of channel and size of image under simultaneous monitoring.
@ Deletion of Already-Registered DVR(SHR-4080P)
- If you select one DVR(SHR-4080P) in DVR List for deletion and press the
[Delete] button, the following message box will pop up. If you press [OK] button
then, DVR(SHR-4080P) will be deleted.
- As long as DVR(SHR-4080P) for deletion is connected with the current Smart
Viewer, the following message box will pop up and DVR(SHR-4080P) will not be
deleted. Be sure to cut the connection between DVR(SHR-4080P) and Smart
Viewer before you delete it.
# Modification of Already-Registered DVR(SHR-4080P)
- If you select one DVR(SHR-4080P) in DVR List for modification and press the
[Modify] button, the following message box will pop up. If you press [OK] button
then, DVR(SHR-4080P) will be modified.
- As long as DVR(SHR-4080P) for modification is connected with the current
Smart Viewer, the following message box will pop up and DVR(SHR-4080P) will
not be modified. Be sure to cut the connection between DVR(SHR-4080P) and
Smart Viewer before you modify it.
10-52
SHR-4080P USER’S MANUAL
●
Site List
- Site List registers multi- DVRs(SHR-4080P) that you want to contact at once by
Smart Viewer at one site for control. You are allowed to register a new Site or
delete or modify the selected Site from the registered list and add DVR(SHR4080P) to the Site selected from Site List or delete it
- In Site List, both the name of a registered Site and the name of DVR(SHR4080P) composing the Site will be listed. One Site can be composed of no more
than 4 DVRs(SHR-4080P).
! Site Addition
- If you press the [New] button, the following window will pop up where you can
input the information on the new Site.
- The information to be typed in is the Site name.
10-53
Note
Site may be named in both English and Korean with no more than 10 texts.
@ Deletion of Already-Registered Site or DVR(SHR-4080P)
- If you select one Site or DVR(SHR-4080P) in Site List for deletion and press
the [Delete] button, the following message box will pop up. If you press [OK]
button then, either Site or DVR(SHR-4080P) will be deleted.
- After being deleted, DVR(SHR-4080P) is still left alive in the Site composition
and so is the information on DVR(SHR-4080P).
- As long as Site or DVR(SHR-4080P) for deletion is connected with the current
Smart Viewer, the following message box will pop up and Site or DVR(SHR4080P) will not be deleted. Be sure to cut the connection between both Site
and DVR(SHR-4080P) and Smart Viewer before you delete it.
# Modification of Already-Registered Site
- If you select one Site in Site List for modification and press the [Modify] button, the following message box will pop up where you can modify the Site
information.
10-54
SHR-4080P USER’S MANUAL
- As long as Site for modification is connected with the current Smart Viewer,
the following message box will pop up and Site will not be modified. Be sure to
cut the connection between Site and Smart Viewer before you modify it.
- If you select one DVR(SHR-4080P) and press the [Modify] button, the following message box will pop up and modification to DVR(SHR-4080P) is prohibited. Modification to DVR(SHR-4080P) shall be done only in DVR List.
●
DVR(SHR-4080P) Addition to Site
- If you press the [Add] button, DVR(SHR-4080P) selected from DVR List will be
added to the Site selected from Site List. Site addition to DVR(SHR-4080P) set
to ADSL is prohibited.
- You may add up to 4 DVRs(SHR-4080P) to one Site and DVR(SHR-4080P) composing Site may be deleted from Site List.
- If you press the [Add] button unless a Site is registered in Site List, a new Site
naming “Site [0]” as a default will be created to which DVR(SHR-4080P) will be
added.
- As long as Site for DVR(SHR-4080P) addition is connected with the current
Smart Viewer, the following message box will pop up and DVR(SHR-4080P) will
not be added to the Site. Be sure to cut the connection between Site and Smart
Viewer before the addition
10-55
S/W Version
- If you press the [S/W Version] button, Smart Viewer version, system requirements, and the version of DVR(SHR-4080P) System S/W, being connected to
Smart Viewer, if ever will be displayed.
- You can upgrade the on-line DVR(SHR-4080P) System S/W remotely. You are
authorized with S/W upgrade in an Admin capacity only. In the capacity of user or
if you are isolated with DVR(SHR-4080P), your access will be denied.
1
2
! Smart Viewer Version and system requirements will be displayed.
@ Here displays the version and name of DVR if any DVR(SHR-4080P) is being
connected with Smart Viewer. You are also able to upgrade DVR(SHR-4080P)
S/W by transmitting it to on-line DVR(SHR-4080P).
10-56
SHR-4080P USER’S MANUAL
●
Smart Viewer Version
- Smart Viewer Version and system requirements will be displayed.
●
DVR Version
- DVR Version not only displays the connected DVR(SHR-4080P) name if any
DVR(SHR-4080P) is being connected with Smart Viewer or the name of
DVR(SHR-4080P) composing a site if any DVR(SHR-4080P) is being connected
with the site but also displays DVR(SHR-4080P) S/W version.
- As long as Smart Viewer is isolated from DVR(SHR-4080P), this part remains
inactivated.
- Each DVR Version has a check box, which is used for S/W Upgrade.
●
DVR(SHR-4080P) S/W Upgrade
- Smart Viewer upgrades on-line DVR(SHR-4080P) S/W remotely.
! Check a DVR(SHR-4080P) to be upgreaded among DVRs(SHR-4080P) on line.
10-57
@ Click the following button to open the “SHR-4080 Firmware” file in tgz format.
# Press the [Upgrade] button to transmit a file to the selected DVR(SHR-4080P)
and start upgrade of DVR(SHR-4080P) S/W.
$ The progress of file transmission and upgrade will be displayed at the bottom.
Caution
Be sure to suspend all the DVR system functions in action such as recording, MENU,
backup, and play before you upgrade DVR(SHR-4080P) S/W.
Never try to turn the DVR(SHR-4080P) power off during such S/W upgrade.
S/W upgrade requires about 5 minutes.
If S/W upgrade is suspended accidentally, the previous S/W will be left intact.
Note
The new Firmware necessary for DVR(SHR-4080P) S/W upgrade shall be downloaded from CCTV Part in Products Section at http://www.samsungelectronics.com.
10-58
Appendix
11
SHR-4080P USER’S MANUAL
1
Product Specification
Item
Specification
CPU
Memory
Operation System
Broadcasting
Input Voltage
Power Comsumption
Video Input
Video
Video Output
Audio Input
Audio
Audio Output
Resolution &
Frame Rate
Live
Monitoring
11-1
Display Mode
32bit RISC CPU
SDRAM : 64MByte
Flash : 8MByte
Embedded OS
PAL System
AC 100-230V, 50/60Hz
85 Watt Max
Composite 8 Channel
- 1.0Vp-p
- 75Ω Hi Z Termination
BNC Type
Loop Through Out 8 Channel
- Auto Termination
Composite 2 Channel
- Nomal Video Output 1 Channel
- Spot Output 1 Channel
- BNC Type
S-Video 1 Channel
- 1.0Vp-p
VGA 1 Channel
Mono 8 Channel
- -5dBm, 600Ω
RCA Type
Mono 1 Channel
- -6dBm
RCA Type
Resolution Frame Rate (1Ch/8Ch)
720x576
25fps/200fps
Single
Quad
Multi Screen : 6, 7, 8, 9
PIP
Sequence
Freeze
2x Zoom
Change the channel location
(4, 6, 7, 8 Division)
Remark
Item
Specification
Compression
Recording
Resolution &
Performance
Recording
Mode
Time Laps
Internal
Storage
Capacity
External
Video : MPEG4
Audio : G.726
Resolution
Quality Level
Level1
Level2
CIF(S)
Level3
Level4
352x288
Level5
Level6
Level7
Level8
Level1
Level2
Level3
Half D1(N)
Level4
720x288
Level5
Level6
Level7
Level8
Level1
Level2
Level3
Full D1(L)
Level4
720x576
Level5
Level6
Level7
Level8
Remark
Max Image Rate
*ips (image
per sec)
25ips
25ips
12.5ips
Normal
REC Key
Emergency
PANIC Key
Schedule
Schedule Table
Event
-Alarm Input
-Motion Detection
-Video Loss
-Pre & Post Recording
PAL : 1/2.5/5/6.25/8.33/12.5/ 25ips
ATA HDD x 4(MAX)
-Primary/Secondary IDE Connector
-MAX HDD Size : 250GB x 4 = 1Tera Byte
IEEE1394 I/F HDD
-MAX 6 (Daisy chain connection)
-MAX HDD Size : 250GB x 6 = 1.5Tera Byte
SCSI HDD
-MAX 6 (Daisy chain connection)
-MAX HDD Size : 150GB x 6 = 900Giga Byte
* Packing
120GB
(Samsung)
x 1EA
11-2
SHR-4080P USER’S MANUAL
Item
Specification
Search Mode
Play Back
Resolution &
Performance
Display Mode
Play Mode
Backup
Alarm
Network
Serial I/F
PC Spec.
Remote
Viewer
Support OS
Function
Operation Temp.
Preservation Temp.
Operation Humidity
Preservation Humidity
Size
Weight
11-3
Calendar
Event
- Normal, Panic, Schedule, Alarm, Motion,
Video Loss
Date/Time
Go to First
Go to Last
Backup Data
Resolution
Decoding Performance
1Ch
4Ch
CIF(352 x 288)
25ips
25ips/1Ch
12.5ips/1Ch
Half D1(720 x 288) 25ips
25ips
12.5ips/1Ch
Full D1(720 x 576)
Single
1Channel Decoding
Quad
4Channel Decoding
PIP 1Channel Decoding + 1Channel Live
-Change the live channel.
Multi Screen 8Channel Live + Decoding
Play, Pause, Stop, 2x Digital Zoom
Fast Forward/Fast Reverse
- 2x, 4x, 8x, 16x, 32x, 64x
Still
Jog Still
Shuttle Fast Forward/Fast Reverse
IEEE1394 External HDD
SCSI External HDD
Input : 8 Input
- 5mA
Output : 4 Relay Output
- 2A/30VDC, 0.5A/125VAC
Reset : 1 Input
- 5mA
Ethernet : 10/100 Base T, ADSL(PPPoE), DHCP
RS-485 PTZ Device Control, Remote Control Device
CPU : Pentium III, 1GHz or higher
RAM : SDRAM 256MB or higher
Graphic Accelerator : Graphic Memory
32MB or higher DirectX : 8.1 or higher
Win98se, WinME, Win2000, WinXP
Live Image Monitoring Mode
Local File Search & Play Back Mode
Remote File Search & Play Back Mode
0ºC ~ 40ºC
-20ºC ~ 60ºC
20% ~ 85% RH
20% ~ 85% RH
430(W) X 88(H) X 400(D)
About 7.1Kg
Remark
2
HDD Specifications
●
●
SCSI I/F External HDD
Maker
RPM
Seagate
10,000
Capactity
36.7 GB
73.4 GB
146.8 GB
Interface
Ultra320 SCSI
Model No
ST336607LC
ST373307LC
ST3146807LC
Internal ATA HDD/IEEE1394 I/F External HDD
Maker
RPM
Samsung
5,400
7,200
7,200
5,400
7,200
Maxtor
Western
Digital
Capactity
120 GB
160 GB
120 GB
160 GB
250 GB
120 GB
160 GB
Interface
Ultra ATA-133
Ultra ATA-133
EIDE
Model No
SV1203N
SV1604N
4R120LO
4R160LO
5A250JO
WD1200LB
WD1600LB
11-4
SHR-4080P USER’S MANUAL
3
Outline Drawing
11-5
4
Factory Default
This restores the Network information and preset values in SHR-4080P to the original
state at the time of factory shipment.
Factory Default will be done if you;
- Use System / Load Factory Default in MENU or,
- If you hold on to the Mode button in Live Mode and keep pressing the CH5
button for 5 seconds, the system will return to the Factory default condition.
Classification
System Setup
Camera Setup
Detailed Items
Time/Date/Language
Factory Setup
Date Format
YYYY-MM-DD
Time Format
24 Hours
Language
English
Summer Time
Off
Password
Password
4321
Password Lock
On
Disk Mode
Disk End Mode
Stop
Disk End Beep
Off
Video
On
Camera Config
PTZ Device
Screen
Audio
On
Title
CAM_01 ~ CAM_08
Auto Seq.
5 sec
ID
Camera No.
Protocol
None
Baudrate
9600
Parity
None
Data
8
Stop
1
Serial Mode
Half Duplex
Brightness
50
Contrast
50
Color
50
11-6
SHR-4080P USER’S MANUAL
Classification
Monitoring Setup
Detailed Items
Duration
Off
OSD Display
Date
On
Time
On
Title
On
Status
On
Spot Out Channel
Event Record
Setup
Off
Monitor Out
Composite Out
PB Channel Position
Right Down
Mode
On
Video Size
Half D1
Quality
Level 8
Rate
25 ips
Continuous Recording
Off
Event Recording
Event Record Mode
Alarm
Motion Detection
Video Loss
11-7
CH1
Spot Out Event Monitor
Record Mode
Setup
Record Schedule
Setup
Factory Setup
Event Monitoring
On
Video Size
Normal
Quality
Level 8
Rate
25 ips
PreAlarm
10 sec
PostAlarm
1 min
Sensor State
Off
Camera
Camera No.
Alarm-Out
None
A.O Dwell Time
10 sec
M.D State
Off
Area
All Area
Sensitivity
Medium
Alarm-Out
None
A.O Dwell Time
10 sec
Vide Loss State
Off
Alarm-Out
None
A.O Dwell Time
10 sec
5
SHR-4080P Smart Viewer Play
Frame Specification
FRAME Viewer Screen
RATE
Split Mode
25
VIDEO SIZE
Full D1(L)
Half D1(N)
CIF (S)
Nine-split
not support
2 frame/sec
2 frame/sec
Quad
not support
2 frame/sec
25 frame/sec
Single
not support
25 frame/sec
25 frame/sec
Full D1(L)
Half D1(N)
CIF (S)
Nine-split
1 frame/sec
1 frame/sec
12.5 frame/sec
Quad
1 frame/sec
12.5 frame/sec
12.5 frame/sec
Single
12.5 frame/sec
12.5 frame/sec
12.5 frame/sec
Full D1(L)
Half D1(N)
CIF (S)
Nine-split
1 frame/sec
8.33 frame/sec
8.33 frame/sec
Quad
8.33 frame/sec
8.33 frame/sec
8.33 frame/sec
Single
8.33 frame/sec
8.33 frame/sec
8.33 frame/sec
Full D1(L)
Half D1(N)
CIF (S)
Nine-split
6.25 frame/sec
6.25 frame/sec
6.25 frame/sec
Quad
6.25 frame/sec
6.25 frame/sec
6.25 frame/sec
Single
6.25 frame/sec
6.25 frame/sec
6.25 frame/sec
Full D1(L)
Half D1(N)
CIF (S)
Nine-split
5 frame/sec
5 frame/sec
5 frame/sec
Quad
5 frame/sec
5 frame/sec
5 frame/sec
Single
5 frame/sec
5 frame/sec
5 frame/sec
Full D1(L)
Half D1(N)
CIF (S)
Nine-split
2.5 frame/sec
2.5 frame/sec
2.5 frame/sec
Quad
2.5 frame/sec
2.5 frame/sec
2.5 frame/sec
Single
2.5 frame/sec
2.5 frame/sec
2.5 frame/sec
Full D1(L)
Half D1(N)
CIF (S)
Nine-split
1 frame/sec
1 frame/sec
1 frame/sec
Quad
1 frame/sec
1 frame/sec
1 frame/sec
Single
1 frame/sec
1 frame/sec
1 frame/sec
12.5
8.33
6.25
5
2.5
1
Note
The play frame specification of Smart Viewer varies on the setup of SHR-4080P Recording Rate and Video
Size or the screen split mode of Smart Viewer. The above specification is applicable only when the main
body of SHR-4080P is connected with a fast network like LAN.
When the main body of SHR-4080P is connected with a slow network like ADSL, the play speed will be
0.5 Frame/sec. In addition, the above specification has been defined to the recommended specification of
your PC. If your PC specification is lower than the recommended, the number of frame to played may
diminish.
11-8
SHR-4080P USER’S MANUAL
6
Troubleshooting(FAQ)
1. The system power is dead and LED in front of the system does not operate at all.
- Please check the power connection.
- Check the power voltage.
- If all your efforts like above end up with nothing, check or exchange the power
supply.
2. Video data remains in the system but some channels displays no video data but
turns all blue.
- Check the image of the camera connected to the system. Improper input of camera input may cause this symptom.
- Check the camera power supply.
- Sometimes, you see this symptom when the video data is connected with multisystems and the video signal from the video data distributor in use feels weak. If
it’s the case, you shall connect the camera images with SHR-4080P DVR directly
to check or improve such a symptom.
3. The REC button in front has no effect on turning on REC LED or recording process.
- Please check the HDD space.
- Please check the Record Mode setup in MENU. It should be Off.
4. All the front LEDs are in operation but the monitor remains black.
- Video out may come out differently with the connected monitor. In short, Video
Out is set to Composite Output but connected to VGA Input Monitor or vice
versa. Then, keep pressing both the "MODE" button and the "0" button on the
left for 5 seconds until LED lights on in the order of 1❖2❖3❖4❖5 to change the
Video Out output mode.
5. The front LED blinks and the logo screen repeatedly appears.
- This symptom may be resulted from failure of HDD connection inside SHR4080P DVR. Take off the cover and check HDD connection status. If HDD connection has no problem, please consult with the shop where you bought SHR4080P DVR.
6. You cannot enter MENU by forgotten password.
- If you forget the password, you shall reset SHR-4080P DVR to the values set at
the factory. Keep pressing both the "MODE" button and the "5" button on the left
for 5 seconds until LED lights on in the order of 1❖2❖3❖4❖5. The password
default is "4321".
11-9
7. The channel button does not operate in Live.
- If the current screen is Event Monitoring, the channel button does not operate.
Then, press the Alarm button to terminate the current screen and select a channel.
8. The cursor cannot reach Start during Calendar Search.
- Please check both the channel and the date for play are left checked. Both shall
be checked for play with Start. The cursor cannot reach the unrecorded date.
9. Alarm, once issued, keeps being issued though you press the front Alarm button
for cancellation.
- Press the front Menu button to cancel Alarm as follows.
1) To cancel Event Monitoring Screen : Monitoring❖ Event Monitoring Duration
Off
2) To cancel Buzzer : Event Record❖ Alarm (Motion Detection/Video Loss)❖
Alarm-Out.
3) To cancel Event : Event Record❖ Alarm (Motion Detection/Video Loss)❖
State Off.
10. Pressing the PTZ button in Live receives no response.
- Check the Protocol and other setup values through Menu❖ Camera❖ PTZ
Device match with the PTZ camera.
11. When you connect several IEEE1394 armored HDDs to SHR-4080P DVR through
Menu, SHR-4080P DVR cannot recognize all the HDDs.
- It requires time to recognize several armored HDDs. Please try again in a few
minutes. If retrial makes no improvement, HDD could be abnormal. Please
exchange the HDD.
12. You cannot connect to SHR-4080P DVR through Smart View.
- Check if 3 Smart Viewer users are in connection with SHR-4080P DVR. SHR4080P DVR allows no more than 3 users’ connection with Smart Viewer at a
time.
- Check the Network setup of SHR-4080P DVR.
- Check Network cable connection.
- When you use DHCP/ADSL(PPPoE) for connection, please check if you get the
right SHR-4080P DVR MAC Address.
- If SHR-4080P DVR is connected to the ADSL network, please check if Bandwidth
is set below 600 Kbps. If the Bandwidth for ADSL is set to high, the connection
with Smart Viewer may be instable due to the heavy network load as the ADSL
speed is low.
11-10
SHR-4080P USER’S MANUAL
13. Smart Viewer in operation is disconnected.
- If you change time, network setup, HDD format, Default Setup, or HDD attachment or detachment for SHR-4080P DVR, the current Smart Viewer will be automatically disconnected.
- Check network connection. Smart Viewer, if disconnected from Network, will try
reconnection up to 5 times. If it remains unconnected after 5 time trial, it will
automatically give up connection.
- As far as SHR-4080P DVR is connected to the ADSL network, you may be disconnected from Smart Viewer when the network conditions goes bad.
14. The Audio icon of Smart Viewer is left inactivated in the Live mode. Setting Audio
to On in the Camera menu of SHR-4080P DVR will make no difference.
- If your PC has no Audio driver or has some problem with Audio play of an Audio
driver, the Audio icon will be inactivated. Please check Audio driver installation
status.
15. When I select the channel which PTZ Camera is connected to in the Live mode of
Smart Viewer, click the "Menu Control" button among PTZ setup buttons to enter
the Function Menu mode in PTZ Camera, and return from the other channel, the
PTZ related buttons have been initialized.
- PTZ control is available in both Smart Viewer and SHR-4080P DVR. Other user
might control PTZ for SHR-4080P DVR to terminate the PTZ Camera Menu or
Auto Pan/Scan/Pattern motions while you select the other channel. This may
cause the initialization.
16. Smart Viewer cannot enter the Search mode after connected to SHR-4080P DVR.
- If you connected with Smart Viewer in the User capacity or through a site composed of more than 2 SHR-4080P DVRs, your entrance into the Search mode is
prohibited.
- If you want your capacity from User to Admin, follow the procedure of Setup ❖
Site Setup❖DVR List and double-click the DVR item to change the connection
information.
17. No Time Bar in the Search
- Time Line can be converted into 2 modes, General(24 Hour Display) and
Extension(2 Hour Display). In the Extension mode, Time Bar may not be seen in
the current time. Please enter the General mode or click the LEFT or RIGHT
button to search Time Bar.
11-11
AB68-00451A (Rev.01)
Download PDF

advertising