advertisement
▼
Scroll to page 2
of 40
DVD-1080P9 DVD-1080PR DVD Player user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/global/register AK68-01753D(01) precautions 1. Setting up - Refer to the identification label located on the rear of your player for its proper operating voltage. - Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not block ventilation holes on any of the components for air circulation. - Do not push the disc tray in by hand. - Do not stack components. - Be sure to turn all components off before moving the player. - Before connecting other components to this player, be sure to turn them off. - Be sure to remove the disc and turn off the player after use, especially if you are not going to use it for a long time. - The mains plug is used as a disconnect device and shall stay readily operable at any time. 2. For your safety - This product utilizes a laser. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. - Do not open covers and do not repair yourself. Refer servicing to qualified personal. 3. Caution - Your player is not intended for industrial use but for domestic purposes. Use of this product is for personal use only. - Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. - Exterior influences such as lightning and static electricity can affect normal operation of this player. If this occurs, turn the player off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The player will operate normally. - When condensation forms inside the player due to sharp changes in temperature, the 2_ precautions player may not operate correctly. If this occurs, leave the player at room temperature until the inside of the player becomes dry and operational. 4. Disc - Do not clean disc using record-cleaning sprays, benzene, thinner, or other volatile solvents that may cause damage to the disc surface. - Do not touch the disc’s signal surface. Hold by the edges or by one edge and the hole in the center. - Wipe the dirt away gently; never wipe a cloth back and forth over the disc. 5. Environmental info - The battery used in this product contains chemicals that are harmful to the environ ment. - So, dispose of batteries in the proper man ner, according to federal, state, and local regulations. The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private non-commercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/OUR 11172-3 or ISO/OUR 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/OUR 11172-3 or ISO/OUR 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/OUR 11172-3 or ISO/OUR 13818-3. CAUTION: USE OF ANY CONTROLS, ADJUSTMENTS, OR PROCEDURES OTHER THAN SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. before you start table of contents Accessories Check for the supplied accessories below. Remote Control User’s Manual Batteries for Remote Control (AAA Size) Video/Audio Cable HDMI Cable The accessories which do not suplied. • Component Cable • HDMI-DVI Cable • Coaxial Cable Install Batteries in the Remote control 1. Open the battery cover on the back of the remote control. 2. Insert two AAA batteries. Make sure that the polarities (+ and -) are aligned correctly. 3. Replace the battery cover. If remote control doesn’t operate properly: - Check the polarity + - of the batteries (Dry-Cell) - Check if the batteries are drained. - Check if remote control sensor is blocked by obstacles. - Check if there is any fluorescent lighting nearby. Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Setup General Features . . . . . . . . . . . . . . . . . . . . . . . . . .4 Disc Type and Characteristics . . . . . . . . . . . . . . . .5 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Tour of the Remote Control . . . . . . . . . . . . . . . . . . .8 Connections Choosing a Connection . . . . . . . . . . . . . . . . . . . . .9 Basic Functions Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . .15 Using the Search and Skip Functions . . . . . . . . .15 Using the Display Function . . . . . . . . . . . . . . . . .16 Using the Disc and Title Menu . . . . . . . . . . . . . . .16 Using the Function Menu . . . . . . . . . . . . . . . . . . .17 Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Advanced Functions Adjusting the Aspect Ratio (EZ View) . . . . . . . . . .18 Selecting the Audio Language . . . . . . . . . . . . . . .18 Selecting the Subtitle Language . . . . . . . . . . . . . .19 Changing the Camera Angle . . . . . . . . . . . . . . . . .19 Using the Bookmark Function . . . . . . . . . . . . . . . .19 Using the Zoom Function . . . . . . . . . . . . . . . . . . .20 Clips Menu for MP3/WMA/JPEG/MPEG4/ CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . .21 MP3/WMA/CD Audio Playback . . . . . . . . . . . . . . .21 MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . .21 Playing Media Files using the USB HOST feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 CD Ripping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Picture CD Playback . . . . . . . . . . . . . . . . . . . . . . .24 Picture CD Playback for HD-JPEG . . . . . . . . . . . .25 Changing Setup Menu Using the Setup Menu. . . . . . . . . . . . . . . . . . . . . .26 Setting Up the Language Features . . . . . . . . . . . .26 Setting Up the Audio Options . . . . . . . . . . . . . . . .27 Setting Up the Display Options . . . . . . . . . . . . . . .28 Setting Up the Parental Control . . . . . . . . . . . . . .31 Setting Up the Anynet+(HDMI-CEC) . . . . . . . . . . .32 Reference Firmware Upgrade. . . . . . . . . . . . . . . . . . . . . . . . .33 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 English _3 setup General Features Excellent Sound Dolby Digital, a technology developed by Dolby Laboratories, provides crystal clear sound reproduction. Screen Both regular and widescreen(16:9) pictures can be viewed. Slow Motion An important scene can be viewed in slow motion. 1080p Playback This player upconverts regular DVDs for playback on 1080p TVs. Parental Control (DVD) The parental control allows users to set the level necessary to prohibit children from viewing harmful movies such as those with violence, adult subject matter, etc. Various On-Screen Menu Functions You can select various languages (Audio/Subtitle) and screen angles while enjoying movies. Progressive Scan Progressive scanning creates an improved picture with double the scan lines of a conventional interlaced picture. EZ VIEW (DVD) Easy View enables picture adjustment to match your TV's screen size (16:9 or 4:3). Digital Photo Viewer (JPEG) You can view Digital Photos on your TV. Repeat You can repeat a song or movie simply by pressing the REPEAT button. MP3/WMA This unit can play discs created from MP3/WMA files. MPEG4 This unit can play MPEG4 formats within an avi file. HDMI (High Definition Multimedia Interface) HDMI reduces picture noise by allowing a pure digital video/audio signal path from the player to your TV. CD Ripping This feature lets you to copy audio files from disc to USB device into MP3 format. (Only Audio CD (CD DA)) 4_ setup Note - Discs which cannot be played with this player. • DVD-ROM • DVD-RAM • CD-ROM • CDV • CDI • CVD • CDGs play audio only, not graphics. - Ability to play back may depend on recording conditions. • DVD-R, +R • CD-RW • DVD+RW, -RW (V mode) - The unit may not play certain CD-R, CD-RW and DVD-R due to the disc type or recording conditions. COPY PROTECTION Many DVD discs are encoded with copy protection. Because of this, you should only connect your DVD player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copyprotected DVD discs. This product incorporates copyright protection technology that is protected by methods claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be auzthorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. PROGRESSIVE SCAN OUTPUTS (576p,720p,1080p) “CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE, IN CASE OF 576, 720, 1080 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR TV SET COMPATIBILITY WITH THIS MODEL 576p, 720p, 1080p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER SERVICE CENTER.” Disc Type and Characteristics This DVD player is capable of playing the following types of discs with the corresponding logos: Disc Types (Logos) Recording Types Audio + Video VIDEO-CD Audio + Video AUDIO-CD Max. Playing Time 12 Cm Single-sided 240 min. Double-sided 480 min. - DVD contains excellent sound and video due to Dolby Digital and MPEG2 system. 8 Cm Single-sided 80 min. Double-sided 160 min. - Various screen and audio functions can be easily selected through the onscreen menu. 12 Cm 74 min. - Video with CD sound, VHS quality & MPEG-1 compression technology. 8 Cm 20 min. 12 Cm 74 min. 8 Cm 20 min. Audio - CD is recorded as a Digital Signal with better audio quality, less distortion and less deterioration of audio quality over time. Disc Markings Region Number ~ PAL Play Region Number PAL broadcast system in U.K, France, Germany, etc. Dolby Digital disc STEREO DIGITAL SOUND Stereo disc Digital Audio disc Both the DVD player and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play. The Region Number for this player is described on the rear panel of the player. DTS disc MP3 disc You must only insert one DVD disc at a time. Inserting two or more discs will not allow to play them back and it may cause damage to the DVD player. DivX Certification DivX, DivX Certified, and associated logos are trademarks of DivXNetworks, Inc and are used under license English _5 ● SETUP DVD Characteristics Disc Size setup Description Front Panel Controls 8 7 9 1. DISC TRAY Place the disc here. 6. STOP ( ) Stops disc play. 2. OPEN/CLOSE ( ) Press to open and close the disc tray. 7. SKIP ( ) / SEARCH Use to reverse skip a scene or music. 3. DISPLAY Operation indicators are displayed here. 8. 4. PLAY/PAUSE ( ) Begin or pause disc play. USB HOST Connect digital still camera, MP3 player, memory stick, Card reader other removable storage devices. 9. 5. SKIP ( ) / SEARCH Use to forward skip a scene or music. POWER ON/OFF ( ) Turn on/off and the player is turned on/off. Front Panel Display DVD CD USB RW HDMI 1080iP720P 7 1. 2. 3. 4. 5. In Disc Indicator : DVD Video, Audio CD, CD-R/RW, DVD-R/RW/RAM, DVD+R/RW DVD VIEW indicator CD indicator USB indicator Disc Media indicator : DVD-R, DVDRW, DVD+R, DVD+RW 6_ setup 6. 7. HDMI indicator : HDMI 480P ➔ “HDMI”, HDMI 720P ➔ “HDMI + 720P”, HDMI 1080i ➔ “HDMI + 1080i”, HDMI 1080P ➔ “HDMI + 1080P” Displays the Total playing time and various messages concerning operations such as PLAY, STOP, LOAD ... noDISC: No disc loaded. OPEN: The disc tray is open. LOAD: Player is loading disc information. Rear Panel ● SETUP 1. AUDIO OUT JACKS - Connect to the Audio input jacks of your television or audio/video receiver. 2. DIGITAL AUDIO JACKS - Use either an coaxial digital cable to connect to a compatible Dolby Digital receiver. - Use either an coaxial digital cable to connect to an A/V Amplifier that contains a Dolby Digital, MPEG2 or DTS decoder. 3. COMPONENT VIDEO OUT JACKS - Use these jacks if you have a TV with Component Video in jacks. These jacks provide PR, PB and Y video. - If P-SCAN Video Output is selected in Setup Menu, progressive scan mode will work. - If I-SCAN Video Output is selected in Setup Menu, interlaced scan mode will work. 4. HDMI OUT JACK - Use the HDMI cable to connect this jack to the HDMI jack on your television for the best quality picture. - If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically within 10 seconds. 5. VIDEO OUT JACK - Use a video cable to connect to the Video input jack on your television. Note - Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN). If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system. - The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input. - There may be no image output if the DVD player is connected to a TV or display that is not compatible with the above format. - Refer to the TV's instruction manual for detailed information regarding the HDMI terminal. - See pages 28 ~ 30 to get more information on how to use the setup menu. English _7 setup Tour of the Remote Control 8. 9. 1 17 18 2 19 20 21 22 23 3 4 5 6 7 8 9 10 24 11 27 10. 11. 12. 13. 14. 25 15. 26 16. 12 17. 18. 13 28 14 29 15 30 16 31 19. 20. 21. 22. 23. 24. 1. 2. 3. 4. 5. 6. 7. DVD POWER Button Turns the power on or off. NUMBER Buttons SUBTITLE (Number 4) Button TITLE MENU (Number 7) Button Brings up the Title Menu. ZOOM/-/-- Button Enlarges the DVD Picture. Use this button to select the channel TV program by inserted the channel (TV mode). TV VOL (+, -) Buttons Control volume. SEARCH Buttos (k/K) Allow you to search forward/backward through a disc. 8_ setup 25. 26. 27. 28. 29. 30. 31. VIDEO SEL. Button Selects video output formats. SKIP Buttons (|k/K|) Use to skip the title, chapter or track. STOP Button (■) MENU Button Brings up the DVD player’s menu. ENTER/π/†,√/® Buttons This button functions as a toggle switch. INFO Button Displays the current disc mode. DISC MENU Button Brings up the Disc menu. OPEN/CLOSE ( ) Button To open and close the disc tray. HDMI SEL. Button HDMI Output resolution setup. DVD Button This button when you use a DVD player. TV Button This button when you use a Samsung TV. EZ VIEW (Number 6) Button The aspect ratio of a picture can easily be adjusted according to the screen size of your TV (16:9 or 4:3). AUDIO (Number 5) Button Use this button to access various audio functions on a disc. BOOKMARK (Number 9) Button REPEAT A-B (Number 8) Button Allows you to repeat play A-B on a disc. STEP/TV SOURCE Button Advances play one frame at a time. Use this button to select an available TV source (mode TV) TV CH (P, Q) Buttons Channel selection. PAUSE Button (∏∏) Pause disc play. PLAY Button () Begin disc play. RETURN Button Returns to a previous menu. EXIT Button Exit the on-screen menu. CANCEL Button Use to remove menus or status displays from the screen. USB Button REPEAT Button Allows you to repeat play a title, chapter, track, or disc. connections Choosing a Connection Before Connecting the DVD Player - Always turn off the DVD player, TV, and other components before you connect or disconnect any cables. - Refer to the user’s manual of the additional components you are connecting for more information on those particular components. Connection to a TV (For Video) 1 Using video/audio cables, connect the VIDEO (yellow)/ AUDIO (red and white) OUT terminals on the rear of the DVD player to the VIDEO (yellow)/AUDIO (red and white) IN terminals of TV. WHITE 2 Turn on the DVD player and TV. RED YELLOW Audio Cable 3 RED WHITE Video Cable YELLOW Press the input selector on your TV remote control until the Video signal from the DVD player appears on the TV screen. Note - Noise may be generated if the audio cable is too close to the power cable. - If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14) - The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV. - If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the DVD player. - If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output mode changes in the following sequence: (I-SCAN ➝ P-SCAN) English _9 ● CONNECTIONS The following shows examples of connections commonly used to connect the DVD player with a TV and other components. connections Connection to a TV (Interlace) - Connecting to your TV using Component video cables. - You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio signals are delivered through the audio output.) 1 Using component video cables, connect the COMPONENT VIDEO OUT terminal on the rear of the DVD player to the COMPONENT IN terminal of TV. 2 Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the DVD player and TV. WHITE GREEN BLUE RED 3 Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen. RED Audio Cable Component Cable RED WHITE RED BLUE GREEN 4 Set the Video Output to I-SCAN in the Display Setup menu. (See pages 28 to 30) You can use the VIDEO SEL. button to change the Video Output mode. (See page 9) Note - If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14) - The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y” depending on the manufacturer. The number and position of terminals can vary depending on the TV set. Please refer to the user's manual of the TV. 10_ connections Connection to a TV (Progressive) 1 Using component video cables, connect the COMPONENT VIDEO OUT terminal on the rear of the DVD player to the COMPONENT IN terminal of TV. ● CONNECTIONS 2 Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of TV. Turn on the DVD player and TV. WHITE GREEN BLUE RED 3 Press the input selector on your TV remote control until the Component signal from the DVD player appears on the TV screen. RED Audio Cable Component Cable RED WHITE RED BLUE GREEN 4 Set the Video Output to P-SCAN in the Display Setup menu. (See pages 28 to 30) You can use the VIDEO SEL. button to change the Video Output mode. (See page 9) To see the progressive video output, - Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system. - Depending on your TV, the connection method may differ from the illustration above. Note - What is "Progressive Scan"? Progressive scan has twice as many scanning lines as the interlace output method has. Progressive scanning method can provide better and clearer picture quality. English _11 connections Connecting to a TV with DVI Jack 1 Using the HDMI-DVI cable , connect the HDMI OUT terminal on the rear of the DVD player to the DVI IN terminal of your TV. 2 WHITE Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of your TV. Turn on the DVD player and TV. RED Audio Cable RED HDMI-DVI cable WHITE 3 Press the input selector on your TV remote control until the DVI signal from the DVD player appears on your TV screen. Connecting to a TV with HDMI Jack 1 Using the HDMI-HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the HDMI IN terminal of your TV. 2 Press the input selector on your TV remote control until the HDMI signal from the DVD player appears on your TV screen. HDMI cable HDMI VIDEO Specifications When you press the HDMI SEL. button, 480p, 576p, 720p, 1080p, 1080i are selected in order. The first press of the HDMI SEL. button brings up the current resolution. The second press allows you to change the HDMI output resolution. - Depending on your TV, certain HDMI output resolutions may not work. - Please refer to the user's manual of your TV. - If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10 seconds. - If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture quality. - If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC). (See page 32). - If your TV has an logo, then it will Supports the Anynet+ Function. 12_ connections • HDMI (High Definition Multimedia Interface) HDMI is an interface to enable the digital transmission of video and audio data with just a single connector. Using HDMI, the DVD player transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack. • HDMI connection description - Though the player uses a HDMI cable, the player outputs only a pure digital signal to the TV. - If TV does not support HDCP (High-bandwidth Digital content protection), snow noise appears on the screen. Analog TVs require an analog video/audio signal. However, when playing a DVD, the data transmitted to a TV is digital. Therefore either a digital-to-analog converter (in the DVD player) or an analog-to-digital converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss. DVI technology is superior because it requires no D/A conversion and is a pure digital signal from the player to your TV. • What is the HDCP? HDCP (High-bandwidth Digital Content Protection) is a system for protecting DVD content outputted via DVI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector . etc). Content is encrypted at the source device to prevent unauthorized Connection to an Audio System (2 Channel Amplifier) 1 Using the audio cables, connect the AUDIO (red and white) OUT terminals on the rear of the DVD player to the AUDIO (red and white) IN terminals of the Amplifier. 2 Using the video signal cable(s), connect the VIDEO or COMPONENT OUT terminals on the rear of the DVD player to the VIDEO or COMPONENT IN terminal of your TV. WHITE RED 3 Audio Cable Turn on the DVD player, TV, and Amplifier. 4 RED WHITE 2-Channel stereo ampilfier Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player. Note - Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears. - Please set the audio in the menu screen according to the Amplifier. (See pages 27-28) - The position of terminals can vary depending on the Amplifier. Please refer to the user's manual of the Amplifier. English _13 ● CONNECTIONS HDMI connector - Both uncompressed video data and digital audio data (LPCM or Bit Stream data). • Why does Samsung use HDMI? connections Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier) 1 If using a coaxial cable, connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier. 2 Using the video signal cable(s), connect the VIDEO, COMPONENT or HDMI OUT terminals on the rear of the DVD player to the VIDEO, COMPONENT or DVI IN terminals of your TV as described on pages 9 to 13. 3 Coaxial Cable Turn on the DVD player, TV, and Amplifier. Dolby digital or DTS amplifier 4 Press the input select button of the Amplifier to select external input in order to hear sound from the DVD player. Refer to your Amplifier's user manual to set the Amplifier's audio input. Note - Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause damage to the speakers and your ears. - Please set the audio in the menu screen according to the Amplifier. (See pages 27 to 28) - The position of terminals can vary depending on the Amplifier. Please refer to the user's manual of the Amplifier. 14_ connections basic functions Playing a Disc - If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input. After plugging in the player, the first time you press the DVD POWER button, this screen comes up: If you want to select a language, press a NUMBER button. (This screen will only appear when you plug in the player for the first time.) If the language for the startup screen is not set, the settings may change whenever you turn the power on or off. Therefore, make sure that you select the language you want to use. Once you select a menu language, you can change it by button on the front panel of the unit for pressing the more than 5 seconds with no disc in the unit. Then the SELECT MENU LANGUAGE window appears again where you can reset your preferred language. Press 1 for English Touche 2 pour Français Drücken Sie 3 für Deutsch Pulsar 4 para Español Premere 5 per Italiano Druk op 6 voor Nederlands Playback 1. Press the OPEN/CLOSE ( ) button and the tray opens. 2. Place a disc gently into the tray with the disc’s label facing up. 3. Press the PLAY () button or OPEN/ CLOSE ( ) button to close the disc tray. - When you stop disc play, the player remembers where you stopped, so when you press PLAY () button again, it will pick up where you left off. 4. Stopping Play Press the STOP (■) button during play. 5. Removing Disc Press the OPEN/CLOSE ( ) button. 6. Pausing Play Press the PAUSE (∏∏) or STEP button on the remote control during play. - Screen stops, no sound. To resume, press the PLAY () button once again. 7. Step Motion Play (Except CD) Press the STEP button on the remote control during play. - Each time the button is pressed, a new frame will appear. Note - If the player is left in the stop mode for more than one minute without any user interaction, a screen saver will be activated. Press the PLAY () button to resume normal play. - If the player is left in the stop mode for more than about 30 minutes, the power will automatically shut off.(Automatic Power-Off Function) - If the player is left for about 5 minutes in pause mode, it will stop. - This ( ) icon indicates an invalid button press. Using the Search and Skip Functions During play, you can search quickly through a chapter or track, and use the skip function to jump to the next selection. Searching through a Chapter or Track During play, press the SEARCH (k or K) button on the remote control for more than 1 second. DVD 2X, 4X, 64X, 128X VCD 4X, 8X CD 2X, 4X, 8X Note - The speed marked in this function may be different from the actual playback speed. - No sound is hearing during search mode (Except CD). Skipping Tracks During play, press the SKIP (|k or K|) button. - When playing a DVD, if you press the SKIP (K|) button, it moves to the next chapter. If you press the SKIP (|k) button, it moves to the beginning of the chapter. One more press makes it move to the beginning of the previous chapter. - When playing a VCD 2.0 in Menu Off mode, or a VCD 1.1 or a CD, if you press the SKIP (K|) button, it moves to the next track. If you press the SKIP (|k) button, it moves to the beginning of the track. One more press makes it move to the beginning of the previous track. English _15 ● BASIC FUNCTIONS Before Play - Turn on your TV and set it to the correct Video Input by pressing TV/VIDEO button on the TV remote control. - No sound is heard during STEP mode. - Press the PLAY () button to resume normal play. - You can only perform step motion play in the forward direction. 8. Slow Motion Play Press the SEARCH (k/K) button to choose the play speed between 1/2, 1/4 and 1/8 of normal during PAUSE or STEP mode. - No sound is heard during slow mode. - Press the PLAY () button to resume normal play. basic functions - If a track exceeds 15 minutes when playing a VCD and you press the K| button, it moves forward 5minutes. If you press the |k button, it moves backward 5 minutes. Note When playing VCD2.0, this function works only when the menu is off. Select Menu Off by pressing the DISC MENU button. Using the Disc and Title Menu Using the Disc Menu 1. During the playback of a DVD disc, press the MENU button on the remote control. 2. Press the π/† buttons to select Disc Menu, then-press the ® or ENTER button. Using the Display Function Press ENTER key for Disc Menu When Playing a DVD/VCD/MPEG4 1. During play, press the INFO button on the remote control. - You can select Info in the function menu by pressing the MENU button. 2. Press the π/† buttons to select the desired item. - When playing VCD2.0, this function works only when the menu is off. Select Menu Off by pressing the DISC MENU button. 3. Press the √/® buttons to make the desired setup and then press the ENTER button. - You may use the number buttons of the remote control to directly access a title, chapter or to start the play back from a desired time. 4. To make the screen disappear, press the INFO button again. Chapter Time Audio Subtitle Return Menu Note - Depending on a disc, the Disc Menu may not work. - You can also use the Disc Menu, using the DISC MENU button on the remote control. - When playing VCD2.0, this function works only when the menu is off. Select Menu Off by pressing the DISC MENU button. Using the Title Menu Note : Title Enter To access the desired title when there is more than one in the disc. For example, if there is more than one movie on a DVD, each movie will be identified. Most DVD discs are recorded in chapters so that you can quickly find a specific passage. Allows playback of the film from a desired time. You must enter the starting time as a reference.The time search function does not operate on some disc. Refers to the language of the film soundtrack. In the example, the soundtrack is played in English 5.1CH. A DVD disc can have up to eight different soundtracks. Refers to the subtitle languages available in the disc. You will be able to choose the subtitle languages or, if you prefer, turn them off from the screen. A DVD disc can have up to 32 different subtitles. 16_ basic functions 1. During the playback of a DVD disc, press the MENU button on the remote control. 2. Press the π/† buttons to select Title Menu, then press the ® or ENTER button. Press ENTER key for Title Menu Enter Return Menu Note - Depending on a disc, the Title Menu may not work. - Title Menu will only be displayed if there are at least two titles in the disc. Using the Function Menu Disc Using the Function Menu (DVD/VCD) Repeat:Off 1. Press the MENU button during playback. Using the A-B Repeat function 1. Press the REPEAT A-B button at the point where you want repeat play to start (A). 2. Press the REPEAT A-B button at the point where you want the repeat play to stop (B). 2. To return to normal play, press the REPEAT A-B button. Info Zoom Bookmark EZ View Angle Enter Repeat:A- Repeat:A-B Return Menu 3. Press the π/† buttons to select one of the Five functions. Then press the ® or ENTER button to access the function. You can also directly select these functions using their respective buttons on the remote control. - INFO - ZOOM - EZ VIEW - BOOKMARK - REPEAT Repeat Play Repeat the current track, chapter, title, a chosen section (A-B), or all of the disc. When playing a DVD/VCD 1. Press the REPEAT button on the remote control. Repeat screen appears. - DVD repeats play by chapter or title, VCD repeat play by disc or track - Chapter : repeats the chapter that is playing. - Title : repeats the title that is playing. - Disc : repeats the disc that is playing. - Track : repeats the track that is playing. - Repeat : Off. Chapter Title Repeat:Off Note - A-B REPEAT does not allow you to set point (B) until at least 5 second of playback time has elapsed after point (A) has been set - Depending on a disc, the Repeat function may not work. - When playing VCD2.0, this function works only when the menu is off. Select Menu Off by pressing the DISC MENU button. Slow Play This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being played etc., so you can study them more closely. When playing a DVD 1. During play, press the PAUSE (∏∏) button. 2. Press the SEARCH (k/K) button to choose the play speed between 1/2, 1/4 and 1/8 of normal during PAUSE or STEP mode. Track English _17 ● BASIC FUNCTIONS 2. Press the π/† buttons to select Function, then press the ® or ENTER button. - Info (See pages 16) - Zoom (See page 20) - Bookmark (See pages 19 to 20) - EZ View (See pages 18) - Angle (See pages 19) advanced functions Adjusting the Aspect Ratio (EZ View) To play back using aspect ratio (DVD) Press the EZ VIEW button. - The screen size changes when the button is pressed repeatedly. - The screen zoom mode operates differently depending on the screen setting in the Display Setup menu. - To ensure correct operation of the EZ VIEW button, you should set the correct aspect ratio in the Display Setup menu. (See pages 28 to 30). 4:3 Letter Box EZ VIEW If you are using a 16:9 TV For 16:9 aspect ratio discs - WIDE SCREEN Displays the content of the DVD title in 16:9 aspect ratio. - SCREEN FIT The top and bottom portions of the screen are cut off. When playing a 2.35:1 aspect ratio disc, the black bars at the top and bottom of the screen will disappear. The picture will look vertically stretched. (Depending on a type of disc, the black bars may not disappear completely.) - ZOOM FIT The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarge For 4:3 aspect ratio discs - Normal Wide Displays the content of the DVD title in 16:9 aspect ratio. The picture will look horizontally stretched. - SCREEN FIT The top and bottom portions of the screen are cut off and the full screen appears. The picture will look vertically stretched. - ZOOM FIT The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged. - Vertical Fit When a 4:3 DVD is viewed on a 16:9 TV, black bars will appear at the left and right of the screen in order to prevent the picture from looking horizontally stretched. If you are using a 4:3 TV For 16:9 aspect ratio discs - 4:3 Letter Box Displays the content of the DVD title in 16:9 aspect ratio.The black bars will appear at the top and bottom of the screen. - 4:3 Pan Scan The left and right portions of the screen are cut off and the central portion of the 16:9 screen is displayed. - SCREEN FIT The top and bottom portions of the screen are cut off and a full screen appears. The picture will look vertically stretched. - ZOOM FIT The top, bottom, left and right of the screen are cut off and the central portion of the screen is enlarged. For 4:3 aspect ratio discs - Normal Screen Displays the content of the DVD title in 4:3 aspect ratio. - SCREEN FIT The top and bottom portions of the screen are cut off and the full screen appears. The picture will look vertically stretched. - ZOOM FIT The top, bottom, left and right portions of the screen are cut off and the central portion of the screen is enlarged. Note This function may behave differently depending on the type of disc. Selecting the Audio Language You can select a desired audio language quickly and easily with the AUDIO button. Using the AUDIO button (DVD/VCD/ MPEG4) 1. Press the AUDIO button. The Audio changes when the button is pressed repeatedly. The audio languages are DVD represented by ENG Dolby Digital 5.1CH abbreviations. AUDIO When playing a VCD you can select among Stereo, Right or Left. Press AUDIO button at remocon repeatedly to select the desired Audio on MPEG4 then press the ENTER . VCD Stereo AUDIO MPEG4 MP3 1/1 AUDIO 2. To remove the AUDIO icon, press the CANCEL or RETURN button. 18_ advanced functions Note - This function depends on audio languages are encoded on the disc and may not work. - A DVD disc can contain up to 8 audio languages. Selecting the Subtitle Language 1. During play or pause mode, press the MENU button on the remote control. 2. Press the π/† buttons to select Function, then press the ® or ENTER button. 3. Press the π/† buttons to select Angle, then press the ® or ENTER button. Info You can select a desired subtitle quickly and easily with the SUBTITLE button. Zoom Bookmark EZ View Angle Using the SUBTITLE button (DVD/ MPEG4) 1. Press the SUBTITLE button. The subtitle languages are represented by abbreviations. The subtitle changes when DVD the button is pressed Off repeatedly. Enter Return Menu 4. Press the √/® buttons or you can use the number buttons on the remote control to select the desired angle. 4/6 SUBTITLE External subtitle option will appear, depends the DivX Disc. Note - If the disc has only one angle, this feature won’t work. Currently, very few discs have this feature. - Depending on the disc, these functions may not work. MPEG4 Subtitle Selection External Subtitle Off readme.TXT Non-standard fonts are not supported Press Subtitle button at remocon repeatedly to select the desired subtitle language on a MPEG4. Enter Return Menu MPEG4 Off SUBTITLE 2. To remove the SUBTITLE icon, press the CANCEL or RETURN button. Note - You have to change the desired subtitle in the Disc Menu, according to discs. Press the DISC MENU button. - This function depends on what subtitles are encoded on the disc and may not work on all DVDs. - A DVD disc can contain up to 32 subtitle languages. - To have the same subtitle language come up whenever you play a DVD; Refer to “Using the Subtitle Language” on page 27. Using the Bookmark Function This feature lets you bookmark sections of a DVD or VCD (Menu Off mode) so you can quickly find them at a later time. Using the Bookmark Function (DVD/VCD) 1. During play, press the MENU button on the remote control. 2. Press the π/† buttons to select Function, then press the ® or ENTER button. Info Zoom Bookmark EZ View Angle Enter Return Menu 3. Press the π/† buttons to select Bookmark, then press the ® or ENTER button. - - - 4. When you reach the scene you want to mark, press the ENTER button. Up to three scenes may be marked at a time. English _19 ● ADVANCED FUNCTIONS - To have the same audio language come up whenever you play a DVD; Refer to “Using the Audio Language” on page 27. Changing the Camera Angle When a DVD contains multiple angles of a particular scene, you can use the ANGLE function. Using the ANGLE function (DVD) If the disc contains multiple angles, the ANGLE appears on the screen. advanced functions 1 - - CANCEL Note - When VCD 2.0 is in Menu Off mode only, this function works. Select Menu Off by pressing the DISC MENU button. - Depending on a disc, the Bookmark function may not work. Clips Menu for MP3/WMA/ JPEG/ MPEG4/CD Audio Recalling a Marked Scene 1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function”. 4. Press the √/® buttons to select a marked scene. 1 2 3 CANCEL 5. Press the PLAY () button to skip to the marked scene. CD Audio or discs with MP3/WMA/JPEG/MPEG4 contain individual songs and/or pictures that can be organized into folders as shown below. They are similar to how you use your computer to put files into different folders. Off Stop Clearing a Bookmark 1~3. The first 1~3 steps are the same as those for “Using the Bookmark Function”. 4. Press the √/® buttons to select the bookmark number you want to delete. Open the disc tray. Place the disc on the tray. Close the tray. The tray closes and this screen displays. T WMA JPEG MP3 MPEG4 Enter 5. Press the CANCEL button to delete a bookmark number. 1 2 3 CANCEL - : Name of currently playing file. - : Current Playback Time. - : Current Playback Mode : There are four pressing the REPEAT button. Using the Zoom Function (DVD/ VCD) Info Return modes. They can be selected in order by Using the Zoom Function 1. During play or pause mode, press the MENU button on the remote control. 2. Press the π/† buttons to select Function, then press the ® or ENTER button. 3. Press the π/† buttons to select Zoom, then press the ® or ENTER button. 4. Press the π/† or √/® buttons to select the part of the screen you want to zoom in-on. Press the ENTER button. - During DVD play, press ENTER to zoom in 2X/4X/2X/Normal in order. - During VCD play, press ENTER to zoom in 2X/4X/2X/Normal-in order. 00:00:00 - Off: Normal Playback - Track: Repeats the current track. - Folder: Repeats the current folder - Random: Files in the disc will be played in random order. - : MP3 file icon. - : CD Audio file icon. - : WMA file icon. - : Folder icon. - : JPEG file icon - : Current Folder icon. - : AVI file icon. Zoom Bookmark EZ View Angle Enter 20_ advanced functions Return Menu Note - When playing MP3, WMA or JPEG, the Picture Quality and the HDMI Resolution cannot be set. - When playing MPEG4 file, the VIDEO SEL. only work in stop mode. Menu CD-R MP3/WMA file Folder Selection The folder can be selected both in Stop or Play mode. - To select the Parent Folder Press the RETURN button to go to parent folder, or press the π/† buttons to select “..” and press ENTER to go to the parent folder. - To select the Sub-Folder Press the π/† buttons to select the desired folder, then press ENTER. R oot WMA JPE G Parent Folder MP3 MU SIC Current Folder 1st Sub-Folders 2nd S ON G FILE 1 Peer Folders S ON G FILE 2 S ON G FILE 3 MP E G4 FILES MP3/WMA/CD Audio Playback 1. Open the disc tray. Place the disc on the tray. Close the tray. - Only one kind of file is played back when a disc or a folder contains both MP3 and WMA files. 2. Press the π/† or √/® buttons to select a song file. Press ENTER to begin playback of the song file. Off Play Because You T 00:00:23 ... Because You Cactus Sad Dayu Wonderful Enter Return REPEAT Repeat Repeat/Random playback Press the REPEAT button to change the playback mode. There are four modes, such as Off, Track, Folder and Random. - Off: Normal Playback - Track: Repeats the current song file. - Folder: Repeats the song files which have the same extension in the current folder. - Random: Song files which have the same extension will be played in random order. To resume normal play, press the CANCEL button. MPEG4 Playback MPEG4 Play Function AVI files are used to contain the audio and video data. Only AVI format files with the “.avi” extensions can be played. 1. Open the disc tray. Place the disc on the tray. Close the tray. 2. Press the π/† or √/® buttons to select an avi file (DivX/XviD) and then press ENTER button. Stop Off /MPEG4 T 00:00:00 ... a01_divx51b-8 a02_divx505b-8 a03_divx502sp-8 a04_divx412-8 Enter Return Menu English _21 ● ADVANCED FUNCTIONS - To select the Peer Folder Press the π/† buttons to select the desired folder, then press ENTER. When you record MP3 or WMA files on CD-R, please refer to the following. - Your MP3 or WMA files should be ISO 9660 or JOLIET format. ISO 9660 format and Joliet MP3 or WMA files are compatible with Microsoft's DOS and Windows, and with Apple's Mac. This format is the most widely used. - When naming your MP3 or WMA files, do not exceed 8 characters, and enter “.mp3, .wma” as the file extension. General name format : Title.mp3. or Title.wma. When composing your title, make sure that you use 8 characters or less, have no spaces in the name, and avoid the use of special characters including: (.,/,\,=,+). - Use a decompression transfer rate of at least 128 Kbps when recording MP3 files. Sound quality with MP3 files basically depends on the rate of compression/decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to MP3 format, of at least 128 Kbps and up to 160 Kbps. However, choosing higher rates, like 192 Kbps or more, only rarely give better sound quality. Conversely, files with decompression rates below 128 Kbps will not be played properly. - Use a decompression transfer rate of at least 64Kbps when recording WMA files. Sound quality with WMA files basically depends on the rate of compression/decompression you choose. Getting CD audio sound requires an analog/digital sampling rate, that is conversion to WMA format, of at least 64Kbps and up to 192Kbps. Conversely, files with decompression rates below 64Kbps or over 192Kbps will not be played properly. Sampling rate that can be supported for WMA files is > 30Khz. - Do not try recording copyright protected MP3 files. Certain "secured" files are encrypted and code protected to prevent illegal copying. These files are of the following types: Windows MediaTM (registered trade mark of Microsoft Inc) and SDMITM (registered trade mark of The SDMI Foundation). You cannot copy such files. - Important: The above recommendations cannot be taken as a guarantee that the DVD player will play MP3 recordings, or as an assurance of sound quality. You should note that cer tain technologies and methods for MP3 file recording on CDRs prevent optimal playback of these files on your DVD player (degraded sound quality and in some cases, inability of the player to read the files). - This unit can play a maximum of 500 files and 500 folders per disc. advanced functions Repeat and Repeat A-B playback DivX3.11 & DivX4 & XviD DivX5 Press the REPEAT button to change playback mode. There are 3 modes, such as Off, Folder and Title. - Folder : repeats the AVI files which have the same extension in the current folder. - Title : repeats the title that is playing. Bitrate may fluctuate: Device may skip decoding the high bitrate portions and begin decoding again when Bitrate returns to normal. 720 x 480 @30fps 720 x 576 @25fps : Maximum bitrate : 4Mbps Press the REPEAT A-B button to set the point where you want repeat play to start (A). Press the REPEAT A-B button again at the point where you want the repeat play to stop (B). - To return to normal play, press the CANCEL button. Note - A-B REPEAT does not allow you to set point (B) until at least 5 second of playback time has elapsed after point (A) has been set Possible warning messages that may appear when trying to play DivX/AVI files are : 1. No Authorization - File with bad registration code. Authorization Error This player is not authorized to play this video. OK MPEG4 Function Description Function Description During play, press the |k or Skip K| button, it moves forward (|k or K|) or backward 5 minutes. During play, press the SEARCH (k or K) button and press again to search at a faster Search speed. Allows you to search (k or K) at a faster speed in an AVI file. (2X, 4X, 8X) Allows you to search at a Slow Motion slower speed in an AVI file. Play (1/2X, 1/4X, 1/8X) Each time the STEP button Step Motion is pressed, a new frame will Play appear. ZOOM 2X/4X/2X/Normal in order Reference page - - Return 2. Unsupported Codec - Files with certain Codec Types, Versions (ex. MP4, AFS and other proprietary codecs) are not suppoerted by this player. Off Stop Sweet Vol 3 T 00:00:20 ... Because You Cactus P 15 File you attempt to play has unsupported codec Sad Dayu Wonderful Sweet Vol 3 Enter Menu Return P 15 P 20 - These functions may not work depending on MPEG4 file. CD-R AVI file This unit can play the following video compression formats within the AVI file format: - DivX 3.11 contents - DivX 4 contents (Based on MPEG-4 Simple Profile) - DivX 5 contents (MPEG-4 simple profile plus additional features such as bi-directional frames. Qpel and GMC are also supported.) - XviD MPEG-4 compliant Contents. DVD-RW & DVD+R Format that support for DivX file : - Basic DivX format DivX3.11 / 4.12/ 5.x - Xvid (MPEG-4 compliant video codec) and DivX Pro - File format : *.avi, *.div, *.divx. This unit supports all resolutions up to maximum below. 22_ advanced functions Enter 3. Unsupported Resolution - Files containing resolutions higher than the player’s specification are not supported. Off Stop /a01_divx51b-8 T 00:00:00 ... a01_divx51b-8 a02_divx505b-8 File you attempt to play has unsupported resolution a03_divx502sp-8 a04_divx412-8 Enter Return Menu Note • The resolution that can be supported by DVD1080P9 model up to 720 x 480 @30 frames/ 720 x 576 @25 frames • This unit supports CD-R/RW written in MPEG4 in accordance with the “ISO9660 format”. Playing Media Files Using the USB Host feature Fast playback To play back the disc at a faster speed, press (k/K) during playback. You can enjoy the media files such as pictures, movies and tunes saved in an MP3 player, USB memory or digital camera in high audio by connecting the storage device to the USB port of the DVD Player. Compatible Devices Using the USB HOST feature 1. USB devices that support USB Mass Storage v1.0. (USB devices that operate as a removable disk in Windows (2000 or later) without additional driver installation.) 2. MP3 Player: Flash type MP3 player. 3. Digital camera: Cameras that support USB Mass Storage v1.0. • Cameras that operate as a removable disk in Windows Disc USB (2000 or later) without additional driver installation. 4. USB Flash Drive: Devices that support USB2.0 or USB1.1. • You may experience a difference in playback quality when you connect a USB1.1 device. 5. USB card Reader: One slot USB card reader and Multi slot USB card reader 3. Press the π/† or √/® buttons to select a file in USB. Press ENTER to Open file. • Depending on the manufacturer. the USB card reader may not be supported. Off Stop • If you install multiple memory devices into a multi card reader, you may experience problems. 6. If you use a USB extension cable, the USB device might not be recognized. Enter Return Menu Note • Each time the USB button on the remote control is pressed, a frame of the USB device selection will appear. • “USB” appears on the display screen. • USB MENU screen appears on the TV screen and the saved file is played. Safe USB Removal To prevent damage to the memory stored in the USB device, perform safe removal before disconnecting the USB cable. - Press the STOP (■) button - Remove the USB cable. Skip Forward/Back During playback, press the (|k/K|) button. • When there is more than one file, when you press the K| button, the next file is selected. • When there is more than one file, when you press the |k button, the previous file is selected. • CBI (Control/Bulk/Interrupt) is not supported. • Digital Cameras that use PTP protocol or require additional program installation when connected to a PC are not supported. • A device using NTFS file system is not supported. (Only FAT 16/32 (File Allocation Table 16/32) file system is supported.) • Some MP3 players, when connected to this product,may not operate depending on the sector size of their file system. • The USB HOST function is not supported if a product that transfers media files by its manufacturer-specific program is connected. • Does not operate with Janus enabled MTP(Media Transfer Protocol) devices. • The USB host function of this product does not support all USB devices. English _23 ● ADVANCED FUNCTIONS 1. Connect the USB device to the USB port on the front of the unit. 2. Press the USB button, Press the π/† button to select the one of partision from USB, then Press ENTER. • Each time you press either button, the playback speed will change as follows : 2x ➞ 4x ➞ 8x. advanced functions CD Ripping Picture CD Playback This feature lets you to copy audio files from disc to USB device into MP3 format. Stop Open the dics tray. Off Track 01 T 00:00:00 Track 01 Place the Audio CD(CD DA) disc on the tray, and close the tray. Connect the USB device to the USB port on the front of the unit. 1. Select the desired folder. 2. Press the π/† buttons to select a Picture file in the clips menu and then press the ENTER button. 3. Press the INFO button on the remote control to select the menu you want to view and then press the ENTER button. Track 02 DEV : SELECT ALL START Track 03 Track 04 Track 05 ENTER RETURN Track 06 Track 07 Track 08 Enter Menu This screen will displayed. Note - Press the STOP button to return to the clips --menu. - When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu. - HD-JPEG must be set to SD 1. With the unit in Stop mode, press the ® button to select the DEV (storage media device) menu, then press ENTER button. 2. Press the π/† buttons to select SELECT, then press the ENTER button to marked all files to be copying. Rotation - To unmarked copying all files press ENTER button again.(UNSELECT Menu) : Each time the ENTER button is pressed, the picture rotates 90 degrees clockwise. - If you want to marked several files to be copying, press the √ button, then press ENTER button on the selected file. Stop Zoom : Press the π/† buttons to select the part of the screen you want to zoom in on. Press the ENTER button. Each time the ENTER button is pressed, the picture is enlarged up to 2X. Off Disc Track 01 T 00:00:00 USB Track 01 Track 02 DEV : SELECT ALL START Track 03 Track 04 Track 05 Track 06 Track 07 Slide Show Track 08 Enter Menu • 3. Press the π/† buttons to select START, then press the ENTER button. : The unit enters slide show mode. • Before beginning the Slide Show, the picture interval must be set. File copy begins. - To cancel the copying in progress, press the CANCEL button. Play • : When this icon is selected and ENTER is pressed, the pictures change automatically with about a 6 second interval. • : The pictures change automatically with about a 12 second interval. • : The pictures change automatically with about a 18 second interval. Off Track 01 T 00:00:00 Track 01 Track 02 DEV : USB 1 UNSELECT ALL Track 03 Track 04 Track 05 CD Ripping START Track 06 Track 07 CANCEL Track 08Cancel Enter Ripping REPEAT Repeat Note - When the CD ripping being processed the player will automatic in play mode. - Only the Audio CD(CD DA) dics can be ripping. 24_ advanced functions TIMER : ENTER RETURN Note - Depending on a file size, the amount of time between each picture may be different from the manual. - If you don’t press any button, the slide show will start automatically in about 10 seconds by default. Must connect to HDMI. Resolution should be 720p/1080i/ 108pi, and HD-JPEG should be in HD mode. MP3-JPEG Playback "Please set the HDMI as highest Resolution which you TV support." 1. Press the π/† buttons to select an MP3 file in the clips menu and then press the ENTER button. 2. Press the π/† buttons to select a JPEG file in the clips menu and then press the ENTER button. - Music willplay from the beginning 3. Press Stop button when you want to stop the playback. 1. Select the desired folder. Off Stop T 00:00:00 WMA JPEG MP3 MPEG4 Enter Menu Return 2. Press the π/† buttons to select a Picture file in the clip menu and then press the ENTER button. • Press the STOP (■) button to return to the clips menu. • When playing a Kodak Picture CD, the unit displays the Photo directly, not the clips menu. Stop Off 00:00:00 1 ... 1 2 3 Enter Return Menu Note - To make the setup menu disappear, press the MENU button. • Rotation Press the √/® button to rotate the screen 90 degrees to the left/right. • Skip Picture Press the |k or K| button to select previous or next picture. • Slide Show Press the PLAY (®) button to start SLIDE function. Press the STOP (■) button to stop SLIDE function. You can play JPEG using music as a backgound. Note MP3 and JPEG files have to be on the same disc. CD-R JPEG Disc - Only files with the “.jpg” and “.JPG” extensions can be played. - If the disc is not closed, it will take longer to start playing and not all of the recorded files may be played. - Only CD-R discs with JPEG files in ISO 9660 or Joliet format can be played. - The name of the JPEG file may not be longer than 8 characters and should contain no blank spaces or special characters (. / = +). - Only a consecutively written multi-session disc can be played. If there is a blank segment in the multi-session disc, the disc can be played only up to the blank segment. - A maximum of 500 images can be stored on a single CD. - Kodak Picture CDs are recommended. - When playing a Kodak Picture CD, only the JPEG files in the pictures folder can be played. - Kodak Picture CD: The JPEG files in the pictures folder can be played automatically. - Konica Picture CD: If you want to see the Picture, select the JPEG files in the clips menu. - Fuji Picture CD: If you want to see the Picture, select the JPEG files in the clips menu. - QSS Picture CD: The unit may not play QSS Picture CD. - If the number of files in 1 Disc is over 500, only 500 JPEG files can be played. - If the number of folders in 1 Disc is over 500, only JPEG files in 500 folders can be played. English _25 ● ADVANCED FUNCTIONS Picture CD Playback for HD-JPEG Note - Depending on a file size, the amount of time between each picture may be different from the set interval time. - The image may be displayed at a smaller size depending on the picture size when displaying images in HD-JPEG mode. - It is recommended to set the "BD Wise" to "Off" In case of playback JPEG image file bigger than 720 X 480 pixel size. changing setup menu Setting Up the Language Features Using the Setup Menu The Setup menu lets you customize your DVD player by allowing you to select various language preferences, set up a parental level, even adjust the player to the type of television screen you have. If you set the player menu, disc menu, audio and subtitle language in advance, they will come up automatically every time you watch a movie. 1. With the unit in Stop mode, press the MENU button on the remote control. Use the π/† buttons to select Setup, then press the ® or ENTER button. Language Setup ® Audio Setup ® Display Setup ® Parental Setup : ® DivX(R) Registration ® Anynet+(HDMI-CEC) : On Enter Return Menu ❶ Language Setup: Setup of the Language. ❷ Audio Setup : Setup of the Audio Options. ❸ Display Setup : Setup of the Display Options. Use to select which type of screen you want to watch and several display options. ❹ Parental Setup :-Setup of the Parental Level. Allows users to set the level necessary to prevent children from viewing unsuitable movies such as those with violence, adult subject matter, etc. ❺ DivX(R) Registration : Please use the Registration code to register this player with the DivX(R) Video On Demand format. To learn more go to www.divx.com/vod. ❻ Anynet+(HDMI-CEC): Setup of the Anynet+(HDMI-CEC) Options. 2. Press the π/† buttons to access the different features. Press the ® or ENTER button to access the sub features. 3. To make the setup screen disappear after setting up, press the MENU button again. Note Depending on the disc, some Setup Menu selections may not work. Using the Player Menu Language 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Language Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select Player Menu, then press the ® or ENTER button. 5. Press the π/† buttons to select the desired language, then press the ® or ENTER button. - The language is selected and the screen returns to Language Setup menu. - To make the setup menu disappear, press the MENU button. LANGUAGE SETUP Player Menu √ English Français Deutsch Español Subtitle Italiano Nederlands DivX Subtitle Disc Menu Audio Enter Return Menu Using the Disc Menu Language This function changes the text language only on the disc menu screens. 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Language Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select Disc Menu, then press the ® or ENTER button. 5. Press the π/† buttons to select the desired language, then press the ® or ENTER button. - If the selected language is not recorded on the disc, the original pre-recorded language is selected. - The language is selected and the screen returns to Language Setup menu. - To make the setup menu disappear, press the MENU button. LANGUAGE SETUP Player Menu Disc Menu Audio Subtitle DivX Subtitle Enter 26_ changing setup menu √ English Français Deutsch Español Italiano Nederlands Return Menu Using the DivX Subtitle Language 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Language Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select Audio, then press the ® or ENTER button. 5. Press the π/† buttons to select the desired language, then press the ® or ENTER button. - Select “Original” if you want the default soundtrack language to be the original language the disc is recorded in. - If the selected language is not recorded on the disc, the original pre-recorded language is selected. - The language is selected and the screen returns to Language Setup menu. - To make the setup menu disappear, press the MENU button. 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Language Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select DivX Subtitle, then press the ® or ENTER button. 5. Press the π/† buttons to select the desired language, then press the ® or ENTER button. - The language is selected and the screen returns to Language Setup menu. - To make the setup menu disappear, press the MENU button. LANGUAGE SETUP LANGUAGE SETUP Player Menu Disc Menu Audio Subtitle DivX Subtitle Enter Menu Using the Subtitle Language 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Language Setup,-then press the ® or ENTER button. 4. Press the π/† buttons to select Subtitle, then press the ® or ENTER button. 5. Press the π/† buttons to select the desired language, then press the ® or ENTER button. - Select “Automatic” if you want the subtitle language to be the same as the language selected as the audio language. - Some discs may not contain the language you select as your initial language; in that case the disc will use its original language setting. - The language is selected and the screen returns to setup menu. - To make the setup menu disappear, press the MENU button. LANGUAGE SETUP Disc Menu Audio Subtitle DivX Subtitle Enter Disc Menu Audio Subtitle DivX Subtitle Enter √ Unicode Western Turkish Central Cyrillic Greek Return Menu Original √ English Français Deutsch Español Italiano Return Player Menu Player Menu √ Automatic English Français Deutsch Español Italiano Return Menu Setting Up the Audio Options Audio Options allows you to setup the audio device and sound status settings depending on the audio system in use. 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Audio Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select the desired item, then a press the ® or ENTER button. Language Setup ® Audio Setup ® Display Setup ® Parental Setup : ® DivX(R) Registration ® Anynet+(HDMI-CEC) : On Enter Return Menu AUDIO SETUP Digital Out : PCM MPEG-2 Digital Out : PCM Dynamic Compression : On PCM Down Sampling : On Power On Music : On Enter Return Menu ❶ Digital Out - PCM : Converts to PCM(2CH) audio. - Bitstream : Outputs Dolby Digital via the digital output. Select Bitstream when connecting to a Dolby Digital Decoder. English _27 ● CHANGING SETUP MENU Using the Audio Language changing setup menu ❷ MPEG-2 Digital Out - PCM : Converts to PCM(2CH) audio. - Bitstream : Converts to MPEG-2 Digital Bitstream (5.1CH). Select Bitstream when using the Digital Audio Output. ❸ Dynamic Compression - On : To select dynamic compression. - Off : To select the standard range. ❹ PCM Down Sampling - On : Select this when the Amplifier connected to the player is not 96KHz compatible. In this case, the 96KHz signals will be down converted to 48KHZ. - Off : Select this when the Amplifier connected to the player is 96KHz compatible. In this case, all signals will be output without any changes. Note : - There is no analog audio output when you play a DTS sound disc. - Even when PCM Down sampling is Off • Some discs will only output down sampled audio through the digital outputs. • To make the Setup menu disappear, press the MENU button ➎ Power On Music This menu is used to activate or deactivate the opening sound when you turn on the DVD player. - On : To turn On Start up music. - Off : To turn Off Start up music. HDMI - If your TV is not compatible with compressed multichannel formats (Dolby Digital, DTS, MPEG), you should set Digital Audio to PCM. - If your TV is not compatible with LPCM sampling rates over 48kHz, you should set PCM Down sampling to On. Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories. “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc. Setting Up the Display Options Display options enable you to set various video functions of the player. 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Display Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select the desired item, then press the ® or ENTER button. 28_ changing setup menu Language Setup ® Audio Setup ® Display Setup ® Parental Setup : ® DivX(R) Registration ® Anynet+(HDMI-CEC) : On Enter Return Menu ❶ TV Aspect Depending on a type of television you have, you may want to adjust the screen setting (aspect ratio). - 4:3 Letter Box : Select when you want to see the total 16:9 ratio screen DVD supplies, even though you have a TV with a 4:3 ratio screen. Black bars will appear at the top and bottom of the screen. - 4:3 Pan&Scan : Select this for conventional size TVs when you want to see the central portion of the 16:9 screen. (Extreme left and right side of movie picture will be cut off.) - 16:9 Wide : You can view the full 16:9 picture on your wide screen TV. DISPLAY SETUP TV Aspect √ 4:3 Letter Box Screen Messa 4:3 Pan&Scan TV System 16:9 Wide Video Output HDMI ® Picture Quality ® Enter Return Menu ❷ Screen Messages Use to turn on-screen messages On or Off. ❸ TV System - NTSC : In case of using NTSC disc • If your TV system only has PAL-Video input, you must choose “PAL”. When you choose “PAL”, Interlace output format is PAL 60 Hz output. • If your TV system only has NTSC, input you must choose “NTSC ”. • If you set up the NTSC TV, HDMI output frame rate is 60 Hz. - PAL : In case of using PAL disc • If your TV system only has NTSC-Video input, you must choose “NTSC”. • If your TV system only has PAL input, you must choose “PAL ”. • If you set up the PAL TV, HDMI output frame rate is 50 Hz. - Auto DISPLAY SETUP TV Aspect : 4:3 L-Box Screen Messages : On TV System NTSC Video Output PAL HDMI √ Auto Picture Quality ® Enter Return Menu ❹ Video Output Setting Up the BD Wise When the player is connected to a SAMSUNG TV which supports “BD Wise”,you can enjoy optimized Picture Quality by setting the “BD Wise” function as “On”. Select Video Output. - I-SCAN : Select when you want to use Component Interlace Out. Progressive Out. • If you press the VIDEO SEL. button, Video output mode is changed in regular sequence in no disc mode. ((I-SCAN ➝ P-SCAN) • If the Yes/No selection in the Display Setup sub Menu is not made within 10 seconds, the screen returns to the previous menu. HDMI SETUP DISPLAY SETUP TV Aspect Screen Messages TV System Video Output √ HDMI Picture Quality Resolution Setting : Auto : 4:3 L-Box : On : Auto Resolution : 576p HD-JPEG : SD BD-Wise I-SCAN P-SCAN Enter Enter Return Off: Off √ On ® Return Menu Menu HDMI SETUP Resolution Setting : Auto ➎ HDMI This setting is used when the unit is connected by HDMI with Display devices (TV, projector, etc). Resolution : BD-Wise HD-JPEG : SD BD-Wise : On - Resolution Setting Enter - Auto : Resolution setting automatically - Manual : Resolution setting manually Return Menu Note This option can be changed only when TV support BD Wise. - Resolution - 480p/576p : 720 x 480, 720 x 576 - 720p : 1280 x 720 - 1080i : 1920 x 1080 How to turn Off the BD Wise - 1080p : 1920 x 1080 If you wish to change to other resolution when "BD Wise On", Please choose a method between these two as follows : - HD-JPEG • HD : High Definition image source - Available when resolution is 720p/1080i in HDMI enabled. • SD : Standard Definition image source. - BD-Wise HDMI SETUP Resolution Setting : Auto Resolution : 576p HD-JPEG : SD BD-Wise : Off Method 1 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Display Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select HDMI, then press the ® or ENTER button. 5. Press the π/† buttons to select resolution you wish to use, then press the ® or ENTER button. HDMI SETUP Resolution Setting : Manual Resolution Enter Return Menu HD-JPEG BD-Wise √ : BD Wise 576P 720p : SD 1080i : On 1080p BD-Wise Enter Return Menu Please choose "Yes" to continue, otherwise choose "No" to keep current setting. English _29 ● CHANGING SETUP MENU 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Display Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select HDMI, then press the ® or ENTER button. 5. Press the π/† buttons to select BD-Wise, then press the ® or ENTER button. Press the π/† buttons to select On, then press the ® or ENTER button. - P-SCAN : Select when you want to use Component changing setup menu HDMI SETUP Do you want to turn off BD Wise Mode and change to selected Resolution? Yes No ❻ Picture Quality - Black Level : Adjusts the brightness of the screen.(On or Off) It does not function in Progressive and PAL mode. - Brightness : Level 1 ~ Level 5 Enter Return Menu Method 2 - Color Saturation : Level 1 ~ Level 5 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. 3. Press the π/† buttons to select Display Setup, then press the ® or ENTER button. 4. Press the π/† buttons to select HDMI, then press the ® or ENTER button. 5. Press the π/† buttons to select BD-Wise, then press the ® or ENTER button. Press the π/† buttons to select Off, then press the ® or ENTER button. HDMI SETUP Resolution Setting : Auto Resolution : 1080p HD-JPEG : SD BD-Wise Enter √ Off: Off On Return Menu The HDMI resolution will be changed to maximum resolution supported by your TV. HDMI SETUP Resolution Setting : Auto Resolution : 1080p HD-JPEG : SD BD-Wise : Off Enter Return Note : - It is recommended to set the "BD Wise" to "Off" In case of playback JPEG image file bigger than 720 X 480 pixel size. 30_ changing setup menu - Contrast : Level 1 ~ Level 5 Menu PICTURE QUALITY Black Level : Off Brightness : Level 3 Contrast : Level 3 Color Saturation : Level 3 Enter Return Menu • Consult your TV User’s Manual to find out if your TV supports Progressive Scan. If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in the TV’s menu system. • If Video Output is set incorrectly, the screen may be blocked. • The resolutions available for HDMI output depend on the connected TV or projector. For details, see the user’s manual of your TV or projector. • When the resolution is changed during playback, it may take a few seconds for a normal image to appear. • If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture quality. Setting Up the Parental Control The Parental Control function works in conjunction with DVDs that have been assigned a rating, which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc. 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. Changing the Password 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. Language Setup ® Audio Setup ® Display Setup ® Parental Setup : ® ® Language Setup ® DivX(R) Registration Audio Setup ® Anynet+(HDMI-CEC) : On Display Setup ® Parental Setup : ® DivX(R) Registration ® Anynet+(HDMI-CEC) : On Enter Return Enter Return Menu 3. Press the π/† buttons to select Parental Setup, then press the ® or ENTER button. Menu 3. Press the π/† buttons to select Parental Setup, then press the ® or ENTER button. Language Setup ® Audio Setup ® Display Setup ® Parental Setup : ® ® Language Setup ® DivX(R) Registration Audio Setup ® Anynet+(HDMI-CEC) : On Display Setup ® Parental Setup : ® DivX(R) Registration ® Anynet+(HDMI-CEC) : On Enter Return Menu 4. Press the π/† buttons to select Rating Level, then press the ® or ENTER button. PARENTAL SETUP Rating Level : Kids Safe Return Menu 5. Enter your password. - By default, password-is set to 0000. Please change password to other than 0000 to activate parental control function. PARENTAL SETUP Rating Level Return Menu PARENTAL SETUP Rating Level :Kids Safe Change Password Change Password Enter Enter 4. Press the π/† button to select Change Password, then press the ® or ENTER button. Enter your new password. Re-enter the new password again. Enter Return Menu PARENTAL SETUP Rating Level :Kids Safe Change Password Enter Password : Kids Safe Change Password Enter Password Enter Return Menu PARENTAL SETUP Enter Return Menu 6. Press the π/† buttons to select the Rating Level you want, then press the ® or ENTER button. e.g) Setting up in Kids Safe. Rating Level :Kids Safe Change Password Enter New Password PARENTAL SETUP Enter Rating Level Change Passwor Enter Return √ Kids Safe Level 2 Level 3 Level 4 Level 5 Level 6 Return Menu Note If you have forgotten your password, see “Forgot Password” in the Troubleshooting Guide. Menu English _31 ● CHANGING SETUP MENU Setting Up the Rating Level To make the setup menu disappear, press the MENU button. For example, if you select up to Level 6, discs that contain Level 7,8 will not play. changing setup menu Setting Up the Anynet+(HDMI-CEC) DVDP Anynet+ is a function that can be used to operate the unit using a Samsung TV remote control, by connecting the DVD 1080P9 to a SAMSUNG TV using a HDMI Cable. (see page 12 to 13) (This is only available with SAMSUNG TVs that support Anynet+. Select On when you connecting the DVD 1080P9 with Samsung TV that support Anynet+. View TV ® Select Device ® Record ® Menu on Device ® Device Operation ® Receiver : Off ® Setup ® Move Exit ENTER TV Menu To make the setup menu disappear, press the MENU button. 1. With the unit in Stop mode, press the MENU button. 2. Press the π/† buttons to select Setup, then press the ® or ENTER button. • You can operate the DVD Player by using TV remote control. (TV buttons that can be used to control the DVD Player : , Language Setup ® Audio Setup ® Display Setup ® Parental Setup : ® DivX(R) Registration ® buttons, , , , , and , buttons. - Select Device : Use this option to select device. Anynet+(HDMI-CEC) : On Enter Return - Menu on Device : Same as MENU button on the DVD Player remote control. Menu - Device Operation : Same as INFO button on the DVD Player remote control. 3. Press the π/† buttons to select Anynet+(HDMI-CEC), then press the ® or ENTER button. Note Language Setup ® Audio Setup ® Display Setup ® Parental Setup : ® DivX(R) Registration ® • If you play a DVD when the TV power is off, the TV will power On. Anynet+(HDMI-CEC) : On Enter Return Menu • If you turn the TV off , the DVD Player will power off automatically. 4. Set the Anynet+(HDMI-CEC) to “On” on your DVD Player, then press the ® or ENTER button. Language Setup ® Audio Setup ® Display Setup ® Parental Setup : ® DivX(R) Registration Off Anynet+(HDMI-CEC) √ On : On ® Enter Return Menu 5. Set the Anynet+ function at your TV. (See the TV instruction manual for more information.). • When you press Anynet+ button on the TV remote control, the below OSD will appear. 32_ changing setup menu • By pressing the PLAY button of the unit while watching TV, the TV screen will change to the play screen. • If you change the HDMI to other sources --(Compos ite,Component,... etc) in TV while playing the DVD disc, the DVD Player will stop playing. reference Firmware upgrade 2. Press the √/® buttons to select Total, then press the ENTER button. Introduction Because the specially new mpeg4 codec continues and it is appearing. What improvements are made depends on the upgrade software you are using as well as the software that your DVD-player contained before the upgrade. How to make an upgrade disc Write the downloaded file onto a blank CD-R or CDRW disc, using the following settings: 1. You have to download a new file through Download Center of Samsung Internet Site (www.samsung.com). 2. Write the file to Disc using CD-RW of your computer. Note - File System CD-ROM ISO Level - Character set ISO 9660 - Finalized, single session - Write speed low Upgrade procedure 1. Open the disc tray. Place the disc on the tray. Close the tray. The Firmware upgrade screen appears. Old Version : 081118.I6.B.1080P9XEG New Version : 081212.V1.B.1080P9XEG Firmware upgrade starts - In the middle of the writing, the tray will open automatically. After taking out the disc, please wait for about 2 minutes. - If the unit was succesfully updated, the unit will turn off and on after closing the tray automatically. When the unit turns on, this screen will display. 3. Press the number buttons to select the desired language Press Touche Drücken Sie Pulsar Premere Druk op 1 2 3 4 5 6 for English pour Français für Deutsch para Español per Italiano voor Nederlands Note - If the “Select Menu Language” doesn’t appear, please contact to “Samsung Service Center”. - Do not press any button and unplug the power code during upgrade. - The upgrade procedure may change, refer to the web site (www.samsung.com). Old Version : 081118.I6.B.1080P9XEG New Version : 081212.V1.B.1080P9XEG Firmware upgrade appears on the display English _33 ● REFERENCE Samsung will often support the software upgrade to improve the performance of this unit to the latest status, through Samsung Internet Site (www.samsung. com). reference Troubleshooting Before requesting service (troubleshooting), please check the following. Problem Action Page No operation can be performed with the remote control. • Check the batteries in the remote control. They may need replacing. • Operate the remote control at a distance of no more than 20 feat. • Remove batteries and hold down one or more buttons for several minutes to drain the microprocessor inside the remote control to the reset it. Reinstall batteries and try to operate the remote control again. P3 Disc does not play. • Ensure that the disc is installed with the label side facing up. • Check the region number of the DVD. P5 The icon appears on screen. • 1. 2. 3. 4. Disc Menu Doesn't appear. • Check if the disc has menu. Play mode differs from the Setup Menu selection. • Some of the functions selected in the Setup Menu may not work properly if the disc is not encoded with the corresponding function. P26 ~ 32 The change ratio cannot be changed. • The Screen Ratio is fixed on your DVDs. P28 ~ 30 No audio. • Make sure you have selected the correct DIgital Output in the Audio Options Menu. P27 ~ 28 The screen is blocked. • Press the button (in front panel) for more than 5 seconds under no disc inside. All setting will revert to factory settings. P15 Forgot password. • Press the button (in front panel) for more than 5 seconds under no disc inside. All setings including the password will revert to the factory settings. Don't use this unless absolutely necessary. P31 If you experience other problems • Go to the contens and find the section of the instruction book that contains the explanations regarding the current problem, and follow the procedure once again. • If the problem still cannot be solved, please contact your nearest authorized service center. The picture is noisy or distorted. • Make sure that the disc is not dirty or scratched. • Clean the disc. No HDMI output • Check the Video output is HDMI enabled. • Check the connection between the TV and the HDMI jack of DVD player. • See if the TV supports this 480p/576p/720p/1080i/1080p DVD player. P12 ~ 13 Abnormal HDMI output screen. • If snow noise appears on the screen, it means that TV does not support HDCP (High-bandwidth Digital Content Protection). P12 ~ 13 HDMI output Jitter • Check your TV system setup correctly. • The screen Jitter phenomenon may occur when frame rate is converted from 50Hz to 60 Hz for 720p/1080i/1080p HDMI (High Definition Multimedia Interface) Output. • Please refer to the user's manual of your TV. P28-30 34_ reference The features or action cannot be completed at this time because : The DVD's software restricts it. The DVD's software doesn't support the feature (e.g., angles). The feature is not available at the moment. You've requested a title or chapter number or search time that is out of range. P2 Specifications Power Requirements AC110~240V, 50/60Hz Power Consumption 8W Weight 1.6 Kg Dimensions +5ºC to +35ºC Operating Humidity Range 10 % to 75 % (DIGITAL VERSATILE DISC) CD : 12CM Disc (COMPACT DISC) CD : 8CM (COMPACT DISC) VCD : 12CM Composite Video Video Output Approx. Play Time (Single Sided, Single Layer Disc) : 135 min. Reading Speed : 4.8 ~ 5.6 m/sec. Maximum Play Time : 74 min. Reading Speed : 4.8 ~ 5.6 m/sec. Maximum Play Time : 20 min. Reading Speed : 4.8 ~ 5.6 m/sec. Maximum Play Time : 74 min (Video+Audio). 1 channel : 1.0 Vp-p (75 Ω load) Pr : 0.70 Vp-p (75 Ω load) Pb : 0.70 Vp-p (75 Ω load) * Maximum Output Level Output Reading Speed : 3.49 ~ 4.06 m/sec. Y: 1.0 Vp-p (75 Ω load) Component Video HDMI Audio 430mm (W) X 203mm (D) X 45mm (H) Operating Temperature Range DVD ● REFERENCE General *Frequency Response *Digital Audio Out 480p, 576p, 720p, 1080p, 1080i 2Vrms 20 Hz to 20 kHz Coaxial terminal (S/PDIF) * : Nominal specification Note - Samsung Electronics Co., Ltd reserves the right to change the specifications with out notice. - Weight and dimensions are approximate. English _35 Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Region North America Latin America Country CANADA MEXICO U.S.A ARGENTINE BRAZIL CHILE NICARAGUA HONDURAS COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA COLOMBIA BELGIUM CZECH REPUBLIC DENMARK FINLAND FRANCE Europe CIS Asia Pacific Middle East & Africa GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL SLOVAKIA SPAIN SWEDEN U.K EIRE AUSTRIA SWITZERLAND RUSSIA KAZAKHSTAN UZBEKISTAN KYRGYZSTAN TADJIKISTAN UKRAINE LITHUANIA LATVIA ESTONIA AUSTRALIA NEW ZEALAND CHINA HONG KONG INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE THAILAND TAIWAN VIETNAM TURKEY SOUTH AFRICA U.A.E Contact Center 1-800-SAMSUNG(726-7864) 01-800-SAMSUNG(726-7864) 1-800-SAMSUNG(726-7864) 0800-333-3733 0800-124-421, 4004-0000 800-SAMSUNG(726-7864) 00-1800-5077267 800-7919267 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-SAMSUNG(726-7864) 0-800-100-5303 01-8000112112 02 201 2418 800-726-786 (800 - SAMSUNG) 70 70 19 70 030-6227 515 3260 SAMSUNG (€ 0,15/Min) 08 25 08 65 65 (€ 0,15/Min) 01805 - SAMSUNG(726-7864 € 0,14/Min) 06-80-SAMSUNG(726-7864) 800-SAMSUNG(726-7864) 02 261 03 710 0900-SAMSUNG (726-7864 € 0,10/Min) 815-56 480 0 801 801 881, 022-607-93-33 80820-SAMSUNG(726-7864) 0800-SAMSUNG(726-7864) 902-1-SAMSU(72678) 0771-400 200 0845 SAMSUNG (7267864) 0818 717 100 0800-SAMSUNG(726-7864) 0800-SAMSUNG(726-7864) 8-800-555-55-55 8-10-800-500-55-500 8-10-800-500-55-500 00-800-500-55-500 8-10-800-500-55-500 8-800-502-0000 8-800-77777 8000-7267 800-7267 1300 362 603 0800 SAMSUNG (0800 726 786) 800-810-5858, 400-810-5858, 010-6475 1880 3698-4698 3030 8282, 1800 110011, 1-800-3000-8282 0800-112-8888 0120-327-527 1800-88-9999 1800-10-SAMSUNG(726-7864) 1800-SAMSUNG(726-7864) 1800-29-3232, 02-689-3232 0800-329-999 1 800 588 889 444 77 11 0860-SAMSUNG(726-7864 ) 800-SAMSUNG (726-7864), 8000-4726 Web Site www.samsung.com/ca www.samsung.com/mx www.samsung.com/us www.samsung.com/ar www.samsung.com/br www.samsung.com/cl www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com/latin www.samsung.com.co www.samsung.com/be www.samsung.com/cz www.samsung.com/dk www.samsung.com/fi www.samsung.com/fr www.samsung.de www.samsung.com/hu www.samsung.com/it www.samsung.com/lu www.samsung.com/nl www.samsung.com/no www.samsung.com/pl www.samsung.com/pt www.samsung.com/sk www.samsung.com/es www.samsung.com/se www.samsung.com/uk www.samsung.com/ie www.samsung.com/at www.samsung.com/ch www.samsung.ru www.samsung.com/kz_ru www.samsung.com/kz_ru www.samsung.ua www.samsung.lt www.samsung.com/lv www.samsung.ee www.samsung.com/au www.samsung.com/nz www.samsung.com/cn www.samsung.com/hk www.samsung.com/in www.samsung.com/id www.samsung.com/jp www.samsung.com/my www.samsung.com/ph www.samsung.com/sg www.samsung.com/th www.samsung.com/tw www.samsung.com/vn www.samsung.com/tr www.samsung.com/za www.samsung.com/ae memo memo memo AK68-01753D(01)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project