Samsung | DVD-P247A | Samsung DVD-P247M User Manual

DVD Player
Lecteur DVD
Reproductor de DVD
DVD-P247M
AK68-00419P
ENG
FRA
SPA
Precautions
1. Setting up
* Refer to the identification label located on the back
panel of your player for its proper operating voltage.
* Install your player in a cabinet with adequate
ventilation holes. (7~10cm) Do not block ventilation
holes on any of the components for circulation of air.
* Do not push the disc tray by the hand.
* Do not stack components.
* Be sure to turn all components off before moving the
player.
* Before connecting other components to this player, be
sure to turn them off.
* Be sure to remove the disc and turn off the player
after use, especially if you don’t use it for a long time.
2. For your safety
* This product utilizes a laser. Use of controls or
adjustments or performance of procedures other than
those specified herein may result in hazardous
radiation exposure.
* Do not open covers and do not repair yourself.
Refer servicing to qualified personal.
3. Caution
* Your player is not intended for industrial use but for
domestic purposes. Use of this product is for
personal use only.
* Do not put any container filled with liquid or any small
metal objects on the player.
* Exterior influences such as lightning and static
electricity can affect normal operation of this player.
If this occurs, turn the player off and on again with the
POWER button, or disconnect and then reconnect the
AC power cord to the AC power outlet. The player will
operate normally.
* When condensation forms inside the player due to
sharp changes in temperature, the player may not
operate correctly. If this occurs, leave the player at
room temperature until the inside of the player
becomes dry and operational.
4. Disc
* Do not clean record-cleaning sprays, benzene,
thinner, or other volatile solvents that may cause
damage to the disc surface.
* Do not touch the disc’s signal surface. Hold by the
edges or by one edge and the hole in the center.
* Wipe the dirt away gently; never wipe a cloth back and
forth over the disc.
Before you start
CAUTION : USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER THAN
SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Table of Contents
Setup
Accessories
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Before you start . . . . . . . . . . . . . . . . . . . . . . . .3
General Features . . . . . . . . . . . . . . . . . . . . . . .4
Disc Type and Characteristics . . . . . . . . . . . . .5
Description-Front Panel . . . . . . . . . . . . . . . . . .6
Description-Rear Panel . . . . . . . . . . . . . . . . . .7
Tour of the Remote Control . . . . . . . . . . . . . . .8
1
EZ VIEW
STANDBY/ON
PLAY
LOADING
Remote Control
Batteries for
Remote Control
(AAA Size)
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . .9
Basic Functions
EZ VIEW
STANDBY/ON
PLAY
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . .11
Using the Search & Skip Functions . . . . . . . .12
Using the Display Function . . . . . . . . . . . . . . .12
Using the Disc and Title Menu . . . . . . . . . . . .13
Using the Function Menu . . . . . . . . . . . . . . . .14
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . .14
Program Play & Random Play . . . . . . . . . . . .15
Slow Repeat Play . . . . . . . . . . . . . . . . . . . . . .15
LOADING
STANDBY/ON
EZ VIEW
PLAY
LOADING
User’s Manual
2
Video/Audio Cable
Advanced Functions
Install Batteries in the Remote
Adjusting the Aspect Ratio (EZ View) . . . . . . .16
Selecting the Audio Language . . . . . . . . . . . .17
Selecting the Subtitle Language . . . . . . . . . . .17
Changing the Camera Angle . . . . . . . . . . . . .18
Using the Instant Replay/Skip Function . . . . .18
Using the Bookmark Function . . . . . . . . . . . .19
Using the Zoom Function . . . . . . . . . . . . . . . .20
Clips Menu for MP3/WMA/JPEG/MPEG4 . . . .20
Folder Selection . . . . . . . . . . . . . . . . . . . . . . .21
MP3/WMA Playback . . . . . . . . . . . . . . . . . . .21
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . .22
Picture CD Playback . . . . . . . . . . . . . . . . . . .24
1. Open the battery cover on the back of the
remote.
2. Insert two AAA batteries. Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
3
STANDBY/ON
EZ VIEW
PLAY
LOADING
If remote doesn’t operate properly:
4
• Check the polarity + - of the batteries (Dry-Cell)
• Check if the batteries are drained.
• Check if remote sensor is blocked by obstacles.
• Check if there is any fluorescent lighting nearby.
Changing Setup menu
Using the Setup Menu . . . . . . . . . . . . . . . . . .25
Setting Up the Language Features . . . . . . . . .25
Setting Up the Audio Options . . . . . . . . . . . . .27
Setting Up the Display Options . . . . . . . . . . . .28
Setting Up the Parental Control . . . . . . . . . . .30
5
Reference
5. Environmental info
* The battery used in this product contains chemicals
that are harmful to the environment.
* So, dispose of batteries in the proper manner,
according to federal, state, and local regulations.
Firmware upgrade . . . . . . . . . . . . . . . . . . . . .32
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . .33
Specifications . . . . . . . . . . . . . . . . . . . . . . . .34
ENG-2
ENG-3
General Features
Disc Type and Characteristics
Excellent Sound
Note
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
* Discs which cannot be played with this player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• HD layer of super Audio CD
• CDGs play audio only, not graphics.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
Programmed Play (CD)
You can program tracks to play in desired order.
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional
interlaced picture.
EZ VIEW (DVD)
Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
This DVD player is capable of playing the following types of discs with the corresponding
logos:
Disc Types (Logos)
Recording Types
DVD
Audio
+
Video
* Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW
* The unit may not play certain CD-R, CD-RW and
DVD-R due to the disc type or recording
conditions.
VIDEO-CD
Audio
+
Video
Disc Size
12 Cm
8 Cm
Max. Playing Time
Characteristics
Single-sided 240 min. • DVD contains excellent sound and
Double-sided 480 min. video due to Dolby Digital and
MPEG-2 system.
•
Various
screen and audio functions
Single-sided 80 min.
can be easily selected through the
Double-sided 160 min.
on-screen menu.
74 min.
12 Cm
8 Cm
20 min.
12 Cm
74 min.
8 Cm
20 min.
• Video with CD sound, VHS
quality & MPEG-1 compression
technology.
COPY PROTECTION
Many DVD discs are encoded with copy
protection. Because of this, you should only
connect your DVD player directly to your TV, not to
a VCR. Connecting to a VCR results in a
distorted picture from copy-protected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection
technology must be authorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise
authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
AUDIO-CD
Audio
Disc Markings
~
PAL
• CD is recorded as a Digital
Signal with better audio quality,
less distortion and less
deterioration of audio quality
over time.
Play Region Number
Play Region Number
Both the DVD player and the discs are coded by region.
These regional codes must match in order for the disc to
play. If the codes do not match, the disc will not play.
PAL broadcast system in U.K, France,
Germany, etc.
The Region Number for this player is described on the
rear panel of the player.
Dolby Digital disc
Repeat
PROGRESSIVE SCAN OUTPUTS (525p/625p)
You can repeat a song or movie simply by pressing
the REPEAT button.
STEREO
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IN CASE OF 525 OR 625 PROGRESSIVE
SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION
TO THE ‘STANDARD DEFINITION’ OUTPUT.
IF THERE ARE QUESTIONS REGARDING OUR TV
SET COMPATIBILITY WITH THIS MODEL 525p AND
625p DVD PLAYER, PLEASE CONTACT OUR
CUSTOMER SERVICE CENTER.”
MP3/WMA
This unit can play discs created from MP3/WMA files.
Instant Replay (DVD)
This function is used to replay the previous
10 seconds of a movie from the current position.
Instant Skip (DVD)
This function skips playback ahead 10 seconds.
MPEG4
DIGITAL
SOUND
Stereo disc
Digital Audio disc
DTS disc
DivX Certification
DivX, DivX Certified, and
associated logos are
trademarks of DivXNetworks, Inc and
are used under license.
MP3 disc
This unit can play MPEG4 formats within an avi file.
ENG-4
ENG-5
Description-Front Panel
Description-Rear Panel
Pr
EZ VIEW
STANDBY/ON
PLAY
LOADING
COAXIAL
Pb
Y
COMPONENT VIDEO OUT
OPTICAL
R
L
ANALOG AUDIO OUT
1
2 3 4 5 6
7
8 9 10
1
1. STANDBY/ON (
)
• When the player is plugged in, the
Power LED lights. If you press the
STANDBY/ON button to turn on the player,
the LED goes out.
6. EZ VIEW
• Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
2. SKIP (
) / SEARCH
• Allow you to search backward through a disc.
Use to skip the title, chapter or track.
8. PLAY LED
• When playing the disc, the Play LED lights.
7. OPEN/CLOSE (
)
• Press to open and close the disc tray.
9. REMOCON RECEIVER
10. LOADING LED
• When loading the disc, the Loading LED lights.
4. PLAY/PAUSE (
)
• Begin or pause disc play.
11. DISC TRAY
• Place the disc here.
Power LED
(Red)
Play LED
(Green)
Loading LED
(Yellow)
Power off/Standby
O
X
X
No disc
X
X
O
Stop
X
X
O
Loading
X
X
Blinks
Play/Skip
X
O
X
Search/Pause
X
Blinks
X
Blinks
Blinks
Blinks
Function
Error
ENG-6
2
3
4
5
6
Rear Panel
1. DIGITAL AUDIO OUT JACKS
• Use either an optical or coaxial digital cable to
connect to a compatible Dolby Digital receiver.
Use to connect to an A/V Amplifier that contains
a Dolby Digital, MPEG-2 or DTS decoder.
5. COMPONENT VIDEO OUT JACKS
• Use these jacks if you have a TV with
Component Video in jacks. These jacks provide
Pr, Pb and Y video.
• If Component (P-SCAN) Video Output is
selected in Setup Menu, progressive scan mode
will work.
• If Component (I-SCAN) Video Output is selected
in Setup Menu, interlaced scan mode will work.
2. ANALOG AUDIO OUT JACKS
• Connect to the Audio input jacks of your
television, audio/video receiver.
6. SCART JACK
• Connect to a TV scart input jack.
3. VIDEO OUT JACK
• Use a video cable to connect to the Video input
jack on your television.
• The Video Output in Setup Menu must be set to
Component (I-SCAN) or S-Video.
5. SKIP (
) / SEARCH
• Allow you to search forward through a disc.
Use to skip the title, chapter or track.
LED
S-VIDEO OUT
11
Front Panel Controls
3. STOP (
)
• Stops disc play.
VIDEO OUT
Important Note
• Consult your TV User’s Manual to find out if your
TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV
User’s Manual’s instructions regarding Progressive
Scan settings in the TV’s menu system.
4. S-VIDEO OUT JACK
• Use the S-Video cable to connect this jack to
S-Video jack on your television for a higher
picture quality.
• The Video Output in Setup Menu must be set to
S-Video.
• If Component (P-SCAN) Video Output is selected
in Setup Menu, Video and S-Video will not work.
• See page 29 to get more information on how to
use the setup menu.
ENG-7
Tour of the Remote Control
Choosing a Connection
6. STOP Button (
)
The following shows examples of connections commonly used to connect the DVD player with a TV
and other components.
7. MENU Button
• Brings up the DVD player’s menu.
11
1
8. RETURN Button
2
• Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
• Returns to a previous menu.
• If you connected an external Audio System, turn on your Audio System and set it to the correct Audio Input.
9. REPEAT A-B Button
• Use to mark a segment to repeat between A and B.
12
13
14
3
4
10. SUBTITLE Button
11. OPEN/CLOSE (
5
Before Connecting the DVD Player
• Refer to the owner’s manual of the additional components you are connecting for more information on those
particular components.
Connection to an Audio System
) Button
• To open and close the disc tray.
6
7
15
16
8
17
18
Method 1
12. CLEAR Button
• Use to remove menus or status displays from the
screen.
13. INSTANT REPLAY Button
• This function is used to replay the previous 10
seconds of a movie from the current position.
9
19
20
21
22
10
Method 2
AUDIO
SYSTEM
14. INSTANT SKIP Button
• This function skips playback ahead 10 seconds.
15. PLAY/PAUSE Button (
2ch Amplifier
Dolby Digital Decoder
Audio Input Jacks
Digital Audio Input Jack
)
• Begin/Pause disc play.
16. INFO Button
• Displays the current disc mode.
17. DISC MENU Button
OR
• Brings up the Disc menu.
18. ENTER/DIRECTION Button
(UP/DOWN or LEFT/RIGHT Buttons)
DVD Function Buttons
• This button functions as a toggle switch.
1. DVD POWER Button
19. EZ VIEW Button
• Turns the power on or off.
• Easy View can convert Letter Box images to full
screen viewing on your conventional TV.
2. NUMBER Buttons
20. REPEAT Button
3. PROG Button
4. STEP Button
L
Analog Audio Output Jacks
COAXIAL
Digital Audio Output Jack
21. ANGLE Button
• Advances play one frame at a time.
/
OPTICAL
R
ANALOG AUDIO OUT
• Allows you to repeat play a title, chapter, track, or
disc.
• Allows you to program a specific order.
5. SEARCH/SKIP Buttons (
DVD
Player
• Use to access various camera angles on a DVD.
,
/
• Allow you to search forward/backward through
a disc. Use to skip the title, chapter or track.
)
22. AUDIO Button
• Use this button to access various audio functions
on a disc.
ENG-8
ENG-9
Choosing a Connection
Playing a Disc
7. Step Motion Play (Except CD)
Connection to a TV (For Video)
Before Play
TV (Normal, Widescreen, Projection, etc..)
• Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
• If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
Basic Audio
Method 1
Method 2
Method 3
Method 4
Method 5
Good
picture
Better
picture
Best
picture
Best
picture
Optimum
picture
After plugging in the player, the first time you press
the DVD POWER button, this screen comes up :
If you want to select a language, press a
NUMBER button. (This screen will only appear
when you plug in the player for the first time.)
If the language for the startup screen is not set,
the settings may change whenever you turn the
power on or off. Therefore, make sure that you
select the language you want to use.
TV
AV
Cable
Scart
Cables
(not
supplied)
S-Video
Cable
OR
Video
Cables
OR
OR
Press the STEP button on the remote during play.
- Each time the button is pressed, a new frame will
appear.
- No sound is heard during STEP mode.
- Press PLAY/PAUSE (
) button to resume normal
play. (You can only perform step motion play in the
forward direction.)
8. Slow Motion Play (Except CD)
Press and hold the
button to choose the play speed
between 1/8, 1/4 and 1/2 of normal during PAUSE or
STEP mode.
- No sound is heard during slow mode.
- Press PLAY/PAUSE (
) button to resume normal
play.
- Reverse slow motion play will not work.
RESUME function
DVD
Player
Pr
R
ANALOG AUDIO OUT
Pb
Y
Pr
Pb
When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE (
) button again, it will pick up
where you left off. (unless the disc is removed or the
player is unplugged, or if you press the STOP (
)
button twice.)
Y
L
VIDEO OUT
S-VIDEO OUT
Audio Output Video Output S-Video
Jack
Jack
Jacks
COMPONENT VIDEO OUT
SCART Jack
Component Video
Jacks
(Interlace)
COMPONENT VIDEO OUT
Component Video
Jacks
(Progressive)
Method 1
DVD Player + TV with Video Input Jack
(The Video Output in Setup Menu must be set to S-Video or SCART Output.)
Method 2
DVD Player + TV with S-Video Input Jack
(The Video Output in Setup Menu must be set to S-Video.)
Method 3
DVD Player + TV with Scart Input Jacks (Audio & Video)
(The Video Output in Setup Menu must be set to SCART Output.)
Method 4
DVD Player + TV with interlace Scan Component Video Jacks
(The Video Output in Setup Menu must be set to Component (I-SCAN).)
Method 5
DVD Player + TV with Progressive Scan Component Video Jacks.
(The Video Output in Setup Menu must be set to Component (P-SCAN).)
• If you want to convert Video Output to Progressive Scan, you have to first connect Video or S-Video on your
TV. Select Component (P-SCAN) in Setup menu and then select “Yes” within 10 seconds.
Finally change the TV's external input to 625p/525p(576p/480p or Component). (See page 29)
• If Component (P-SCAN) Video Output is selected in Setup Menu, Video and S-Video will not work.
Important Note
• Consult your TV User’s Manual to find out if your TV supports Progressive Scan.
If Progressive Scan is supported, follow the TV User’s Manual’s instructions regarding Progressive Scan
settings in the TV’s menu system.
• Depending on your TV, the Method of connection may differ from the illustration above.
ENG-10
Play
1. Press the OPEN/CLOSE button.
The STANDBY indicator light goes out and the tray
opens.
2. Place a disc gently into the tray with the disc’s
label facing up.
3. Press the PLAY/PAUSE (
) button or
OPEN/CLOSE button to close the disc tray.
Note
• If the player is left for about 5 minutes in pause
mode, it will stop.
• If the player is left in the stop mode for more than
about 30 minutes, the power will automatically shut
off. (Automatic Power-Off Function)
• If the player is left in the stop mode for more than
one minute without any user interaction, a screen
saver will be activated. Press the PLAY/PAUSE
(
) button to resume normal play.
• This
icon indicates an invalid button press.
4. Stopping Play
Press the STOP (
) button during play.
5. Removing Disc
Press the OPEN/CLOSE button.
6. Pausing Play
Press the PLAY/PAUSE (
) or STEP button on the
remote during play.
- Screen stops, no sound.
- To resume, press the PLAY/PAUSE (
) button once
again.
ENG-11
Using the Search & Skip Functions
During play, you can search quickly through a
chapter or track, and use the skip function to
jump to the next selection.
Searching through a Chapter or Track
Press the SEARCH
or
button on the
remote for more than 1 second.
If you want to search at a faster speed on the DVD,
VCD or CD, press and hold the button.
DVD
2X, 8X, 32X, 128X
VCD
4X, 8X
CD
2X, 4X, 8X
Using the Display Function
When Playing a DVD/VCD/CD
1. During play, press the INFO button on the remote.
Using the Display Function
To access the desired title when there is
Title more than one in the disc.
2. Use the UP/DOWN buttons to select the desired
item.
For example, if there is more than one
movie on a DVD, each movie will be
identified.
3. Use the LEFT/RIGHT buttons to make the
desired setup and then press ENTER.
• You may use the number buttons of the remote
control to directly access a title, chapter or to
start the playback from the desired time.
Chapter chapters so that you can quickly find a
4. To make the screen disappear, press the INFO
button again.
Using the Disc and Title Menu
Using the Disc Menu
1. During the playback of a DVD disc, press the
MENU button on the remote.
2. Select Disc Menu using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
Most DVD discs are recorded in
specific passage (similar to tracks on an
audio CD).
Allows playback of the film from a
Time desired time. You must enter the starting
time as a reference.
Refers to the language of the film
DVD
Audio soundtrack. In the example, the
DVD
Skipping Tracks
During play, press the
Title
or
01
Chapter 02
button.
Time
• When playing a DVD, if you press the
button, it
moves to the next chapter. If you press the
button, it
moves to the beginning of the chapter. One more press
makes it move to the beginning of the previous chapter.
Audio
Subtitle
0 : 00: 13
soundtrack is played in English 5.1CH. A
DVD disc can have up to eight
different soundtracks.
Using the Title Menu
Refers to the subtitle languages
2. Select Title Menu using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
ENG 5.1CH
Off
Subtitle available in the disc.
• When playing a VCD 2.0 in Menu Off mode, or a VCD 1.1
or a CD, if you press the
button, it moves to the next
track. If you press the
button, it moves to the
beginning of the track. One more press makes it move to
the beginning of the previous track.
1. During the playback of a DVD disc, press the
MENU button on the remote.
VCD
You will be able to choose the subtitle
languages or, if you prefer, turn them off
from the screen.
A DVD disc can have up to 32 different
subtitles.
VCD
Track 01
Time 0 : 00: 48
Note
* When in VCD 2.0 mode (Menu On mode), this
function does not work. (See page 12)
• If a track exceeds 15 minutes when playing a VCD and
you press the
button, it moves forward 5 minutes.
If you press the
button, it moves backward 5 minutes.
Note
* When playing a VCD 2.0, you can choose Menu
On or Menu Off by using the DISC MENU
button.
CD
CD
Track 01
Time 0 : 00: 48
ENG-12
Note
• Depending on a disc, the Title and Disc Menus
may not work.
• Title Menu will only be displayed if there are at
least two titles in the disc.
• You can also use the Disc Menu, using the DISC
MENU button on the remote.
• In VCD 2.0, the DISC MENU button is used to
select Menu On or Menu Off mode.
ENG-13
Using the Function Menu
Using the Function Menu
1. Press the MENU button during playback.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
3. Function selection screen appears: Info, Zoom,
Bookmark, Repeat and EZ View.
-
Info (See Page 12~13)
Zoom (See Page 20)
Bookmark (See Page 19)
Repeat (See Page 14)
EZ View (See Page 16)
Repeat Play
Program Play & Random Play
Repeat the current track, chapter, title, a
chosen section (A-B), or all of the disc.
Program Play (CD)
When playing a DVD/VCD/CD
2. Use the LEFT/RIGHT buttons to select
PROGRAM. Press the ENTER button.
1. Press the REPEAT button on the remote.
Repeat screen appears.
2. Select Chapter, Title or A-B using the
LEFT/RIGHT buttons.
• Chapter ( ) : repeats the chapter that is playing.
• Title ( T ) : repeats the title that is playing.
• A-B : repeats a segment of the disc that you select.
DVD
4. Use the UP/DOWN button to highlight one of the
5 functions. Then press the RIGHT or ENTER
button to access the function.
1. Press the PROG button.
3. Use the LEFT/RIGHT/UP/DOWN buttons to select
the first track to add to the program.
Press the ENTER button. The selection numbers
appear in the Program Order box.
4. Press the PLAY/PAUSE (
) button.
The disc will be played in programmed order.
PROGRAM
Off
01
T
01 A - B
REPEAT
Slow Repeat Play
This feature allows you slowly to repeat
scenes containing sports, dancing, musical
instruments being played etc. so you can
study them more closely.
When playing a DVD/VCD
1. During play, press the PLAY/PAUSE (
button.
)
2. Press and hold the
button to choose the play
speed between 1/8, 1/4 and 1/2 of normal during
PAUSE or STEP mode.
3. Press the REPEAT A-B button to select the point
where the function starts. (A)
RANDOM
4. Press the REPEAT A-B button to select the point
where the function ends. (B)
ENTER
PROGRAM 01
Program Order
Track
VCD/CD
Off
T
01
05
09
13
01
D
01 A - B
REPEAT
02
06
10
14
03
07
11
15
04
08
12
16
ENTER
-----
------
------
------
CLEAR
3. Press ENTER.
Note
• You can also directly select these functions using
their respective buttons on the remote.
4. To return to normal play, press REPEAT again,
then press the LEFT/RIGHT buttons to select Off
and press ENTER.
* REPEAT A-B button
• Press the REPEAT A-B button to select the point where
the function starts. (A)
The B is automatically highlighted.
• Press the REPEAT A-B button to select the point where
the function ends. (B)
• To terminate the function, press the 'CLEAR' button or
the 'REPEAT A-B' button again.
• A-B REPEAT does not allow you to set point (B) until at
least 5 seconds has elapsed after point (A) has been
set.
Note
• DVD repeats play by chapter or title, CD and VCD
repeat play by disc or track.
• Depending on a disc, the Repeat function may not
work.
• When in VCD 2.0 mode (Menu On mode), this
function does not work. (See page 12)
ENG-14
Random Play (CD)
1. Press the PROG button.
Note
• The disc will play from A to B repeatedly at the
speed you chose.
• To terminate the function, press the 'CLEAR'
button or the 'REPEAT A-B' button again.
• A-B REPEAT does not allow you to set point (B)
until at least 5 seconds has elapsed after point (A)
has been set.
• When in VCD 2.0 mode (Menu On mode), this
function does not work. (See page 12)
2. Use the LEFT/RIGHT buttons to select RANDOM.
Press the ENTER button.
PROGRAM
RANDOM
Note
• Depending on a disc, the Program and Random
Play functions may not work.
• This unit can support a maximum of 20
programmed tracks.
• While in playback mode, press the CLEAR button
on the remote control to cancel Programmed Play
or Random Play.
ENG-15
Adjusting the Aspect Ratio (EZ View)
Selecting the Audio Language
To play back using aspect ratio (DVD)
If you are using a 4:3 TV
Press the EZ VIEW button.
• The screen size changes when the button is
pressed repeatedly.
• The screen zoom mode operates differently
depending on a screen setting in the initial setup
menu.
• To ensure correct operation of the EZ VIEW
button, you should set the correct aspect ratio in
the initial setup (See page 28).
1. For 16:9 aspect ratio discs
• 4:3 Letter Box
Displays the content of the DVD title in 16:9
aspect ratio. The black bars will appear at the
top and bottom of the screen.
• 4:3 Pan Scan
The left and right of the screen are cut off and
displays the central portion of the 16:9 screen.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture will look vertically stretched.
If you are using a 16:9 TV
1. For 16:9 aspect ratio discs
• Wide Screen
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
Displays the content of the DVD title in 16:9
aspect ratio.
• Screen Fit
The top and bottom of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the
black bars at the top and bottom of the screen
will disappear. The picture will look vertically
stretched. (Depending on a type of disc, the
black bars may not disappear completely.)
2. For 4:3 aspect ratio discs
• Normal Screen
Displays the content of the DVD title in 4:3
aspect ratio.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture would look vertically stretched.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
2. For 4:3 aspect ratio discs
• Normal Wide
Displays the content of the DVD title in 16:9
aspect ratio. The picture will look horizontally
stretched.
• Screen Fit
The top and bottom of the screen are cut off
and the full screen appears.
The picture will look vertically stretched.
Note
• This function may behave differently depending on
a type of disc.
• Zoom Fit
The top, bottom, left and right of the screen are
cut off and the central portion of the screen is
enlarged.
You can select a desired audio quickly and
easily with the AUDIO button.
You can select a desired subtitle quickly and
easily with the SUBTITLE button.
Using the AUDIO button
Using the SUBTITLE button
1. Press the AUDIO button.
1. Press the SUBTITLE button.
ENG-16
- The subtitle languages are represented by
abbreviations.
2. The Audio changes when the button is pressed
repeatedly.
The audio languages are represented by abbreviations.
DVD
2. The subtitle changes when the button is pressed
repeatedly.
DVD
ENG DOLBY DIGITAL 5.1CH
AUDIO
ENG
- In case of a VCD or CD, you can select among Stereo,
Right or Left.
Stereo
SUBTITLE
- Use the LEFT/RIGHT buttons to select the desired
subtitle language on a MPEG4 then press the ENTER.
VCD/CD
MPEG4
AUDIO
None
- Use the LEFT/RIGHT buttons to select the desired
Audio on a MPEG4 then press the ENTER.
MPEG4
3. To remove the SUBTITLE icon, press the CLEAR
or RETURN button.
MP3 1/8
3. To remove the AUDIO icon, press the CLEAR or
RETURN button.
Note
• This function depends on what audios are
encoded on the disc and may not work.
• A DVD disc can contain up to 8 audio languages.
• How to have the same audio language come up
whenever you play a DVD;
Refer to “Setting Up the Language Features” on
page 26.
• Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black
bars will appear at the left and right of the
screen in order to prevent the picture from
looking horizontally stretched.
Selecting the Subtitle Language
Note
• This function depends on what subtitles are
encoded on the disc and may not work.
• A DVD disc can contain up to 32 subtitle
languages.
• How to have the same subtitle language come
up whenever you play a DVD;
Refer to “Setting Up the Language Features” on
page 27.
ENG-17
Changing the Camera Angle
Using the Instant Replay/Skip Function
When a DVD contains multiple angles of a
particular scene, you can use the ANGLE
function.
Using the Instant Replay function (DVD)
Using the ANGLE button
If you press the INSTANT REPLAY button, the
current scene moves backward about 10 seconds,
and plays back.
If the disc contains multiple angles, the ANGLE
appears on the screen.
1. Press the ANGLE button, then ANGLE icon will
appear with the current angle number and the
number of angles available.
If you miss a scene, you can see it again using
this function.
* Depending on a disc, the Instant Replay function may not
work.
This feature lets you bookmark sections of a
DVD or VCD (Menu Off mode) so you can
quickly find them at a later time.
Using the Bookmark Function (DVD/VCD)
1. During play, press the MENU button on the
remote.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
Recalling a Marked Scene
1. During play, press the MENU button on the
remote and select the Bookmark.
2. Use the LEFT/RIGHT buttons to select a marked
scene.
3. Press the PLAY/PAUSE (
the marked scene.
) buttons to skip to
3. Select Bookmark using the UP/DOWN buttons,
then press the RIGHT or ENTER button.
2. Press the ANGLE button repeatedly to the
desired angle.
4. Use the LEFT/RIGHT buttons to move to the
desired bookmark icon.
3. To remove the ANGLE icon, press the CLEAR or
RETURN button.
4/6
Using the Bookmark Function
5. When you reach the scene you want to mark,
press the ENTER button. The icon will change to
a number (1, 2, or 3).
ANGLE
Clearing a Bookmark
Using the Instant Skip function (DVD)
Use this function to skip playback about 10
seconds ahead of the current scene.
Press the INSTANT SKIP button.
Note
• If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Playback will skip ahead 10 seconds.
- Depending on a disc, this function may not work.
1. During play, press the MENU button on the
remote and select the Bookmark.
2. Use the LEFT/RIGHT buttons to select the
bookmark number you want to delete.
3. Press the CLEAR button to delete a bookmark
number.
Note
• Up to three scenes may be marked at a time.
• When in VCD 2.0 mode (Menu On mode), this
function does not work. (See page 12)
• Depending on a disc, the Bookmark function may
not work.
ENG-18
ENG-19
Using the Zoom Function
Using the Zoom Function (DVD/VCD)
1. During play or pause mode, press the MENU
button on the remote.
2. Use the UP/DOWN buttons to highlight Function,
then press the RIGHT or ENTER button.
Clips Menu for MP3/WMA/JPEG/MPEG4
Discs with MP3/WMA/JPEG/MPEG4 contain
individual songs, pictures or movies that can
be organized into folders as shown below.
They are similar to how you use your
computer to put files into different folders.
3. Select Zoom using the UP/DOWN buttons, then
press the RIGHT or ENTER button.
1. Open the disc tray.
2. Place the disc on the tray.
- Place the disc with the labeled side up.
4. Use the UP/DOWN or LEFT/RIGHT buttons to
select the part of the screen you want to zoom in
on.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
Folder Selection
MP3/WMA Playback
The folder can only be selected in the Stop
mode.
• To select the Parent Folder
Press the RETURN button to go to parent folder,
or use the UP/DOWN buttons to select “..” and
press ENTER to go to the parent folder.
• To select the Peer Folder
Use the LEFT/RIGHT buttons to highlight left
window. Use the UP/DOWN buttons to select the
desired folder, then press ENTER.
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
- During VCD play, press ENTER to zoom in 2X/Normal
in order.
2. Place the disc on the tray.
- Place the disc with the labeled side up.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
MP3/WMA Play Function
1. Select the desired folder.
• To select the Sub-Folder
Use the LEFT/RIGHT buttons to highlight right
window. Use the UP/DOWN buttons to select the
desired folder, then press ENTER.
5. Press the ENTER button.
1. Open the disc tray.
2. Use the UP/DOWN or LEFT/RIGHT buttons to
select a song file.
3. Press ENTER to begin playback of the song file.
Root
WMA
JPEG
Parent Folder, Current Folder
and Peer Folders
•
Folders and Files in
Current Folder
: Name of currently playing file.
Parent Folder
MP3
MUSIC
Current Folder
1st
Sub-Folders
2nd
•
: Current Playback Time.
Repeat/Random playback
SONG FILE 1
•
: Current Playback Mode : There are 4
modes. They can be selected in order by
pressing the REPEAT button.
- Off : Normal Playback
- Track : Repeats the current track.
- Folder : Repeats the current folder.
- Random : Files in the disc will be played
in random order.
Note When you play a MPEG4(AVI) file, refer
to page 22.
Peer Folders
SONG FILE 2
SONG FILE 3
MPEG4 FILES
Press the REPEAT button to change playback
mode. There are 4 modes, such as Off, Track,
Folder and Random.
- Off : Normal Playback
- Track : Repeats the current song file.
- Folder : Repeats the song files which have the
same extension in the current folder.
- Random : Song files which have the same
extension will be played in random
order.
* To resume normal play, press the CLEAR button.
•
: MP3 file icon.
•
: AVI file icon.
•
: WMA file icon.
•
: Folder icon.
•
: JPEG file icon.
•
: Current Folder
icon.
ENG-20
ENG-21
MP3/WMA Playback
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R,
please refer to the following.
• Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
• When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file
extension.
General name format of: Title.mp3. or Title.wma.
When composing your title, make sure that you use 8
characters or less, have no spaces in the name, and avoid
the use of special characters including: (.,/,\,=,+).
• Use a decompression transfer rate of at least 128
Kbps when recording MP3 files.
Sound quality with MP3 files basically depends on the rate
of compression/decompression you choose. Getting CD
audio sound requires an analog/digital sampling rate, that
is conversion to MP3 format, of at least 128 Kbps and up
to 160 Kbps. However, choosing higher rates, like 192
Kbps or more, only rarely give better sound quality.
Conversely, files with decompression rates below 128
Kbps will not be played properly.
• Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the
rate of compression/decompression you choose.
Getting CD audio sound requires an analog/digital
sampling rate, that is conversion to WMA format, of at
least 64Kbps and up to 192Kbps.
Conversely, files with decompression rates below 64Kbps
or over 192Kbps will not be played properly.
• Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected
to prevent illegal copying. These files are of the following
types: Windows MediaTM (registered trade mark of
Microsoft Inc) and SDMITM (registered trade mark of The
SDMI Foundation). You cannot copy such files.
• Important: The above recommendations cannot be taken
as a guarantee that the DVD player will play MP3
recordings, or as an assurance of sound quality. You
should note that certain technologies and methods for
MP3 file recording on CD-Rs prevent optimal playback of
these files on your DVD player (degraded sound quality
and in some cases, inability of the player to read the files).
MPEG4 Playback
MPEG4 Playback
1. Open the disc tray.
Using the Display Function
2. Place the disc on the tray.
- Place the disc with the labeled side up.
1. During play, press the INFO button on the remote.
3. Close the tray.
- The tray closes and you should get a screen
that looks like the one below.
MPEG4 Play Function
AVI files are used to contain the audio and video
data. Only AVI format files with the “.avi” extensions
can be played.
1. Select the desired folder. (See page 21 to select
the folder)
2. Use the UP/DOWN buttons to select the desired
item.
(
3. Use the LEFT/RIGHT buttons to make the
desired setup and then press ENTER.
• You may use the number buttons of the remote
control to directly access a title or to start the
playback from the desired time.
(
4. To make the screen disappear, press the INFO
button again.
Title
Audio
Subtitle
Size
Function
Description
Skip
or
During play, press the
or
button, it moves forward
or backward 5 minutes.
Press the SEARCH
or
button on the remote for
more than 1 second.
Allows you to search at a
faster speed in an AVI file.
(2X, 4X, 8X)
Allows you to search at a
slower speed in an AVI file.
(1/8X, 1/4X, 1/2X)
Each time the STEP button
is pressed, a new frame will
appear.
)
Search
or
)
Slow Motion
Play
DivX
Time
2. Use the UP/DOWN or LEFT/RIGHT buttons to
select an avi file (DivX/XviD) and then press the
ENTER button.
MPEG4 Function Description
Step Motion
Play
01
0: 00: 13
ZOOM
MP3 1/8
Reference page
2X/4X/2X/Normal in order
-
-
P 11
P 11
P 20
None
640x272
- These functions may not work depending on
MPEG4 file.
CD-R AVI file
To access the desired title when there is
Title more than one in the disc.
Allows playback of the film from a
Time desired time. You must enter the starting
time as a reference.
To select the desired language of the
Audio title soundtrack. The MP3, AC3 and
WMA are supported. You can use this
function using the AUDIO button.
(See page 17)
Repeat Playback
Press the REPEAT button to change playback
mode. There are 4 modes, such as Off, Folder, Title
and A-B (a distance between two points appointed
by user).
Off
F
FD
T
01 A - B
REPEAT
ENTER
) : repeats the AVI files which have the same
extension in the current folder.
• Title ( ) : repeats the title that is playing.
• A-B : repeats a segment of the file that you select.
T
• This unit can play a maximum of 3000 files and 300
folders per disc.
ENG-22
F
This unit supports all resolutions up to maximum below.
You will be able to choose the subtitle
Subtitle languages or, if you prefer, turn them off
from the screen. You can use this
function using the SUBTITLE button.
(See page 17)
Size
• Folder (
This unit can play the following video compression
formats within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple
Profile)
- DivX 5 contents (MPEG-4 simple profile plus
additional features such as bi-directional frames.
Qpel and GMC are also supported)
- XviD MPEG-4 compliant Contents.
File Size has a relationship with
resolution of a title. The larger file size
is, the higher resolution is displayed.
If the file resolution is small, it scales up
automatically. So you can see the larger
screen.
DivX3.11 & DivX4 & XviD
DivX5
Bitrate may fluctuate:
Device may skip decoding
the high bitrate portions
and begin decoding again
when Bitrate returns to
normal.
720 x 480 @30fps
720 x 576 @25fps
: Maximum bitrate : 4Mbps
Note
• Some MPEG-4 files created on a personal
computer may not be play back. That is why Codec
Type, Version and Higher resolution over
specification is not supported.
• This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
ENG-23
Picture CD Playback
Using the Setup Menu
1. Select the desired folder. (See page 21 to select
the folder)
2. Use the UP/DOWN buttons to select a Picture file in
clips menu and then press the ENTER button. You
should get a screen that looks like the one below.
ENTER RETURN
Note
• If no buttons on the remote control pressed for 10
seconds, the menu will disappear.
Press the INFO button on the remote control to
display the menu again.
• Press the STOP button to return to the clips menu.
• When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
CD-R JPEG Discs
• Use the INFO button on the remote control to select
the menu you want to view and then press the ENTER
button.
•
: Returns to the Album Screen.
• To see the next 6 pictures, press the
• To see the previous 6 pictures, press the
button.
button.
•
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
•
: Each time the ENTER button is pressed, the
picture is enlarged up to 4X.
(Normal ➝ 2X ➝ 4X ➝ 2X ➝ Normal)
•
: The unit enters slide show mode.
*Before beginning the Slide Show, the picture interval
must be set.
TIMER:
ENTER RETURN
•
: When this icon is selected and ENTER is
pressed, the pictures change automatically
with about a 6 second interval.
•
: The pictures change automatically with about
a 12 second interval.
•
: The pictures change automatically with about
a 18 second interval.
• Only files with the ".jpg" and ".JPG" extensions can
be played.
• If the disc is not closed, it will take longer to start
playing and not all of the recorded files may be
played.
• Only CD-R discs with JPEG files in ISO 9660 or Joliet
format can be played.
• The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or
special characters (. / = +).
• Only a consecutively written multisession disc can be
played. If there is a blank segment in the multisession
disc, the disc can be played only up to the blank
segment.
• A maximum of 3000 images can be stored on a single
CD.
• Kodak Picture CDs are recommended.
• When playing a Kodak Picture CD, only the JPEG
files in the pictures folder can be played.
• Kodak Picture CD : The JPEG files in the pictures
folder can be played automatically.
• Konica Picture CD : If you want to see the Picture,
select the JPEG files in the clips menu.
• Fuji Picture CD : If you want to see the Picture, select
the JPEG files in the clips menu.
• QSS Picture CD : The unit cannot play QSS Picture
CD.
• If the number of files in 1 Disc is over 3000, only 3000
JPEG files can be played.
• If the number of folders in 1 Disc is over 300, only
JPEG files in 300 folders can be played.
The Setup menu lets you customize your DVD
player by allowing you to select various
language preferences, set up a parental level,
even adjust the player to the type of television
screen you have.
If you set the player menu, disc menu, audio
and subtitle language in advance, they will
come up automatically every time you watch a
movie.
Using the Player Menu Language
1. With the unit in Stop mode, press the MENU
button on the remote. Select Setup using
UP/DOWN buttons, then press the RIGHT or
ENTER button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
Language Setup : Setup of the Language.
Audio Setup : Setup of the Audio Options.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
Display Setup : Setup of the Display Options.
Use to select which type of screen you want to
watch and several display options.
Parental Setup : Setup of the Parental Level.
Allows users to set the level necessary to
prevent children from viewing unsuitable
movies such as those with violence, adult
subject matter, etc.
DivX(R) Registration : Please use the
Registration code to register this player with
the DivX(R) Video on Demand service.
This will allow you to rent and purchase videos
using the DivX(R) Video On Demand format.
To learn more go to www.divx.com/vod.
4. Select Player Menu using UP/DOWN buttons,
then press the RIGHT or ENTER button.
LANGUAGE SETUP
Disc Menu
Title Menu
Function
Setup
5. Use the UP/DOWN buttons to select the desired
language.
2. Use the UP/DOWN buttons on the remote to
access the different features.
3. Press the ENTER or RIGHT button to access the
sub features.
To make the setup screen disappear after setting
up, press the MENU button again.
*Depending on a file size, the amount of time between
each picture may be different from the manual.
*If you don’t press any button, the slide show will start
automatically in about 10 seconds by default.
Setting Up the Language Features
6. Press the ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
- To make the SETUP menu disappear, press the
RETURN or LEFT button.
Note
Depending on a disc, some Setup Menu selections
may not work.
ENG-24
ENG-25
Setting Up the Language Features
Setting Up the Language Features
Setting Up the Audio Options
Using the Disc Menu Language
Using the Audio Language
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
This function changes the text language only on the
disc menu screens.
1. With the unit in Stop mode, press the MENU
button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
1. With the unit in Stop mode, press the MENU
button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
3. Select Audio Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
3. Select Language Setup using UP/DOWN
buttons, then press the RIGHT or ENTER button.
4. Select Audio using UP/DOWN buttons, then
press the RIGHT or ENTER button.
4. Select Subtitle using UP/DOWN buttons, then
press the RIGHT or ENTER button.
4. Select Disc Menu using UP/DOWN buttons, then
press the RIGHT or ENTER button.
5. Use the UP/DOWN buttons to select the desired
language.
5. Use the UP/DOWN buttons to select the desired
language.
5. Use the UP/DOWN buttons to select the desired
language.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
preference.
- Select “Others” if the language you want is not listed.
- Select “Others” if the language you want is not listed.
Some discs may not contain the language you select
as your initial language; in that case the disc will use its
original language setting.
- Select “Others” if the language you want is not listed.
AUDIO LANGUAGE
4. Use the UP/DOWN buttons to select the desired
item. Then press the RIGHT or ENTER button.
Audio
SUBTITLE LANGUAGE
Automatic
Original
Others
Subtitle
Others
6. Press the ENTER button.
Dolby Digital Output
- The language is selected and the screen returns to
Language Setup menu.
6. Press the ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
1. PCM : Converts to PCM(2CH) 48kHz audio. Select
PCM when using the Analog Audio Outputs.
6. Press the ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
2. Bitstream : Converts to Dolby Digital Bitstream
(5.1CH). Select Bitstream when using the
Digital Audio Output.
Note
• If the selected language is not recorded on the
disc, the original pre-recorded language is
selected.
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
Note • Be sure to select the correct Digital Output or
no audio will be heard.
MPEG-2 Digital Out
1. PCM : Converts to PCM(2CH) audio. Select PCM
when using the Analog Audio Outputs.
2. Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 7.1CH). Select Bitstream when
using the Digital Audio Output.
ENG-26
ENG-27
Setting Up the Audio Options
DTS
1. Off : Doesn’t output digital signal.
2. On : Outputs DTS Bitstream via digital output only.
Select DTS when connecting to a DTS Decoder.
Note There is no analog audio output when you play
DTS sound disc.
Setting Up the Display Options
1. With the unit in Stop mode, press the MENU button.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
3. Select Display Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
Setting Up the Display Options
Still Mode
These options will help prevent picture shake in still
mode and display small text clearer.
Video Output
Select Video Output.
1. S-Video : Select when you want to use Video and
S-Video Out.
1. Auto : When selecting Auto, Field/Frame mode will be
automatically converted.
2. Component (I-SCAN) : Select when you want to use
Component Interlace
(625i/525i) Out.
2. Field : Select this feature when the screen shakes in
the Auto mode.
Dynamic Compression
1. On : To select dynamic compression.
2. Off : To select the standard range.
3. Frame : Select this feature when you want to see
small letters more clearly in the Auto mode.
3. Component (P-SCAN) : Select when you want to use
Component Progressive
(625p/525p) Out.
PCM Down Sampling
1. On : Select this when the amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
Screen Messages
Use to turn on-screen messages On or Off.
4. SCART Output : Select when you want to use Scart
Out.
2. Off : Select this when the amplifier connected to the
player is 96KHz compatible. In this case, all
signals will be output without any changes.
• RGB : Select when you want to use SCART RGB
Out.
• S-Video : Select when you want to use SCART
S-Video Out.
• Video : Select when you want to use SCART
Video Out.
Black Level
Adjusts the brightness of the screen.(On/Off)
4. Use the UP/DOWN buttons to select the desired
item. Then press the RIGHT or ENTER button.
Note
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
• Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
• “DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
TV Aspect
Depending on a type of television you have, you may
want to adjust the screen setting (aspect ratio).
1. 4:3 Letter Box : Select when you want to see the total
16:9 ratio screen DVD supplies, even though you have
a TV with a 4:3 ratio screen. Black bars will appear at
the top and bottom of the screen.
2. 4:3 Pan Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
TV System
* If the Yes/No selection in the Display Setup sub Menu
is not made within 10 seconds, the screen returns to
the previous menu.
1. NTSC Disc : In case of using NTSC disc
• If your TV system only has PAL-Video input, you
must choose “PAL”. When you choose “PAL”,
Interlace output format is PAL 60 Hz output.
• If your TV system only has NTSC, input you must
choose “NTSC Output”.
2. PAL Disc : In case of using PAL disc
• If your TV system only has NTSC-Video input, you
must choose “NTSC Output”.
• If your TV system only has PAL input, you must
choose “PAL Output”.
3. 16:9 Wide : You can view the full 16:9 picture on your
widescreen TV.
TV ASPECT
4:3 Letter Box
4:3 Pan Scan
16:9 Wide
ENG-28
Important Note
• Consult your TV User’s Manual to find out if your
TV supports Progressive Scan. If Progressive
Scan is supported, follow the TV User’s Manual’s
instructions regarding Progressive Scan settings in
the TV’s menu system.
• If the screen is blocked by setting the wrong Video
Output, see page 33.
ENG-29
Setting Up the Parental Control
The Parental Control function works in conjunction
with DVDs that have been assigned a rating - which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
Setting Up the Parental Control
5. Enter your password. The Re-enter Password
screen appears to confirm the password.
Enter your password again.
The player is locked ( ).
1. With the unit in Stop mode, press the MENU
button.
CREATE PASSWORD
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
Setting Up the Rating Level
1. With the unit in Stop mode, press the MENU
button.
6. Select the Rating Level you want using
UP/DOWN buttons.
For example, if you select up to Level 6, discs that
contain Level 7, 8 will not play.
- To cancel the Rating Level, select No using RIGHT or
ENTER in Use Password.
2. Select Setup using UP/DOWN buttons, then
press the RIGHT or ENTER button.
The player is locked ( ).
e.g) Setting up in LEVEL6.
Enter Password
- - - -
3. Select Parental Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
0~9
CREATE PASSWORD
Re-enter Password
- - - -
3. Select Parental Setup using UP/DOWN buttons,
then press the RIGHT or ENTER button.
0~9
4. Enter your password.
The Parental Setup screen appears.
About the Change Password;
- Highlight Change Password using UP/DOWN buttons.
- Press ENTER button.
The Change Password screen appears.
- Enter your new password. Enter the new password again.
4. Use RIGHT or ENTER to select Yes if you want
to use a password. The Enter Password screen
appears.
Note
• How to make the SETUP menu disappear or
return to menu screen during set up;
Press RETURN or LEFT button.
• If you have forgotten your password, see Forgot
Password in the Troubleshooting Guide.
PARENTAL SETUP
Use Password
: No
5. Select Rating Level using UP/DOWN buttons,
and press ENTER or RIGHT button.
ENG-30
ENG-31
Firmware upgrade
Introduction
Troubleshooting
4. Press the ENTER button.
Samsung will often support the software upgrade to
improve the performance of this unit to the latest
status, through Samsung Internet Site
(www.samsung.com).
Because the specially new mpeg4 codec continues
and it is appearing. What improvements are made
depends on the upgrade software you are using as
well as the software that your DVD-player contained
before the upgrade.
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or
CD-RW disc, using the following settings:
1. You have to download a new file through
Download Center of Samsung Internet Site
(www.samsung.com).
Before requesting service (troubleshooting), please check the following.
Firmware upgrade starts
Problem
5. In the middle of the writing, the tray will open
automatically. After taking out the disc, please
wait for about 2 minutes.
6. If the unit was successfully updated, the unit will
turn off and on after closing the tray automatically.
When the unit turns on, this screen will display.
2. Write the file to Disc using CD-RW of your
computer.
Action
Page
No operations can be
performed with the remote.
• Check the batteries in the remote. They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several
minutes to drain the microprocessor inside the remote to reset it.
Reinstall batteries and try to operate the remote again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
5.1 channel sound is not
being reproduced.
• 5.1 channel sound is reproduced only when the following conditions
are met. :
1) The DVD player is connected with the proper amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “Dolby 5.1 ch” mark
on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
P9
The
icon appears on
screen.
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is
out of range.
P27~28
P11
Note
• File System CD-ROM ISO Level
• Character set ISO 9660
Disc Menu doesn’t appear.
• Check if the disc has a Menu.
Play mode differs from the
Setup Menu selection.
• Some of the functions selected in the Setup Menu may not work
properly if the disc is not encoded with the corresponding function.
P24~31
The screen ratio cannot
be changed.
• The Screen Ratio is fixed on your DVDs.
P28~29
No audio.
• Make sure you have selected the correct Digital Output in the Audio
Options Menu.
P27~28
The screen is blocked
• Press power on from a cold start with no disc in the unit.
Press the STOP (
) and PLAY (
) buttons simultaneously on
the front panel for 5 seconds. The SELECT MENU LANGUAGE display will appear.
Select the number button of the desired language.
P28~29
• Press power on from a cold start with no disc in the unit.
Press the STOP (
) and PLAY (
) buttons simultaneously on
the front panel for 5 seconds. The SELECT MENU LANGUAGE display will appear. Select the number button of the desired language.
Press the MENU button, and then press DOWN button to select the
Parental Setup. The Parental Setup is now unlocked as
indicated on the display. You can change your password.
P30~31
• Finalized, single session
• Write speed low
7. Select the desired language.
Note • If the “Select Menu Language” does't
appears, please contact to “Samsung
Service Center”.
• Do not press any button and unplug
the power code during upgrade.
Upgrade procedure
1. Press OPEN/CLOSE to open the disc tray.
2. Insert the upgrade CD-R disc, label facing up.
• The upgrade procedure may change,
refer to the web site
(www.samsung.com).
3. Press OPEN/CLOSE to close the disc tray.
Firmware upgrade appears on the display
Forgot password
If you experience other
problems.
ENG-32
• Go to the contents and find the section of the instruction book that
contains the explanations regarding the current problem, and follow
the procedure once again.
• If the problem still cannot be solved, please contact your nearest
authorized service center.
ENG-33
Specifications
General
Power Requirements
AC 110~240 V, 50/60 Hz
Power Consumption
12 W
Weight
1.9 Kg
Dimensions
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
Disc
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
CD : 8Cm
(COMPACT DISC)
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
VCD : 12Cm
Composite Video
SCART Jack
Video
Output
Component Video
S-VIDEO
SCART Jack
2 Channel
Audio
Output
430mm (W) X 207mm (D) X 46mm (H)
*Frequency Response
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
1 channel : 1.0 Vp-p (75 Ω load)
R(Red) : 0.7 Vp-p (75 Ω load)
G(Green) : 0.7 Vp-p (75 Ω load)
B(Blue) : 0.7 Vp-p (75 Ω load)
Composite Video : 1.0 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Color Signal : 0.3 Vp-p (75 Ω load)
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Luminance Signal : 1.0 Vp-p (75 Ω load)
Chrominance Signal : 0.3 Vp-p (75 Ω load)
2 Channel : L(1/L), R(2/R)
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*S/N Ratio
110 dB
*Dynamic Range
100 dB
*Total Harmonic Distortion
0.004 %
*: Nominal specification
• Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
• Weight and dimensions are approximate.
ENG-34
Download PDF

advertising