Samsung | HT-C5550W | Samsung HT-C5550W User Manual

HT-C5500
HT-C5530W
HT-C5550W
5.1CH Blu-ray
Home Cinema System
user manual
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Safety Information
Safety Warnings
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK).
NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This symbol indicates “dangerous
CAUTION : TO PREVENT ELECTRIC
voltage” inside the product that presents SHOCK, MATCH WIDE BLADE OF PLUG
a risk of electric shock or personal injury. TO WIDE SLOT, FULLY INSERT.
WARNING
• To reduce the risk of fire or electric shock, do
not expose this appliance to rain or moisture.
CLASS 1
KLASSE 1
LUOKAN 1
KLASS 1 PRODUCTO
This symbol indicates important
instructions accompanying the
product.
LASER PRODUCT
LASER PRODUKT
LASER LAITE
LASER APPARAT
LÁSER CLASE 1
CAUTION
• Apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
• The Mains plug is used as a disconnect device and shall
stay readily operable at any time.
• This apparatus shall always be connected to a AC outlet
with a protective grounding connection.
• To disconnect the apparatus from the mains, the plug
must be pulled out from the mains socket, therefore the
mains plug shall be readily operable.
CLASS 1 LASER PRODUCT
This Compact Disc player is classified as a
CLASS 1 LASER product.
Use of controls, adjustments or performance of
procedures other than those specified herein
may result in hazardous radiation exposure.
CAUTION
• INVISIBLE LASER RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED, AVOID EXPOSURE TO BEAM.
English
Precautions
• Ensure that the AC power supply in your house complies with the identification sticker located on the back of
your product.
• Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation
(7.5~10cm).
• Do not place the product on amplifiers or other equipment which may become hot.
Make sure the ventilation slots are not covered.
• Do not stack anything on top of the product.
• Before moving the product, ensure the Disc Insert Hole is empty.
• In order to disconnect the product completely from the power supply, remove the main plug from the wall outlet,
especially when left unused for a long period of time.
• During thunderstorms, disconnect the AC main plug from the wall outlet. Voltage peaks due to lightning could
damage the product.
• Do not expose the product to direct sunlight or other heat sources. This could lead to overheating and
malfunction of the product.
• Protect the product from moisture, and excess heat or equipment creating strong magnetic or electric fields (i.e.
speakers.).
• Disconnect the power cable from the AC supply if the product malfunctions.
• Your product is not intended for industrial use. Use of this product is for personal use only.
• Condensation may occur if your product or disc has been stored in cold temperatures. If transporting the
product during the winter, wait approximately 2 hours until the product has reached room temperature before
using.
• The batteries used with this product contain chemicals that are harmful to the environment.
Do not dispose of batteries in the general household trash.
English
Safety Information
Cautions on Handling and Storing Discs
Small scratches on the disc may reduce sound
and picture quality or cause skipping.
Be especially careful not to scratch discs when
handling them.
Holding discs
• Do not touch the playback side of the disc.
• Hold the disc by the edges so that fingerprints will not
get on the surface.
• Do not stick paper or tape on the
disc.
Disc Storage
• Do not keep in direct sunlight
• Keep in a cool ventilated area
• Keep in a clean Protection jacket.
Store vertically.
✎ NOTE
 Do not allow the discs to become contaminated with
dirt.
 Do not load cracked or scratched discs.
Handling and Storing Discs
If you get fingerprints or dirt on the disc, clean it with a
mild detergent diluted in water and wipe with a soft cloth.
• When cleaning, wipe gently from the inside to
the outside of the disc
✎ NOTE
 Condensation may form if warm air comes into
contact with cold parts inside the product. When
condensation forms inside the product, it may not
operate correctly. If this occurs, remove the disc
and let the product stand for 1 or 2 hours with the
power on.
English
Licence
• This product incorporates copyright protection
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorized by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized
by Macrovision. Reverse engineering or disassembly is
prohibited.
• ABOUT DIVX VIDEO: DivX® is a digital
video format created by DivX,Inc. This is
an official DivX Certified device that plays
DivX video. Visit www. divx.com for more information
and software tools to convert your files into DivX video.
ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified®
device must be registered in order to play DivX Videoon-Demand (VOD) content. To generate the registration
code, locate the DivX VOD section in the device setup
menu. Go to vod.divx.com with this code to complete
the registration process and learn more about DivX
VOD.
DivX Certified to play DivX video up to HD 1080p,
including premium content.
• iPod is a trademark of
Apple Inc., registered in
the U.S. and other
countries.
iPhone is a trademark of Apple Inc.
• Manufactured under licence from Dolby Laboratories.
Dolby, Pro Logic and the double-D symbol are
trademarks of Dolby Laboratories.
• < Open Source Licence Notice >
In the case of using open source software, Open Source
Licences are available on the product menu.
Copyright
© 2010 Samsung Electronics Co., Ltd. All rights
reserved.
Contents
Safety Information
Safety Warnings
Precautions
Cautions on Handling and Storing Discs
Licence
Copyright
Getting Started
7
8
12
13
13
14
15
Icons that will be used in manual
Disc Types and Characteristics
Accessories
Description
Front Panel
Rear Panel
Remote control
CONNECTIONS
17
23
25
26
27
28
Connecting the Speakers
Connecting External Devices/your TV via HDMI
Connecting the Video Out to your TV
Connecting Audio from External Components
Connecting to the Network
Connecting the FM Antenna
Setup
29
30
31
31
31
31
33
33
33
33
33
34
34
35
35
35
36
37
37
37
37
37
37
37
38
38
38
39
39
42
42
42
43
43
43
Before Starting (Initial Settings)
Setting the Menu
Display
TV Aspect
BD Wise
Resolution
HDMI Format
Movie Frame (24 Fs)
Progressive Mode
Still Mode
HDMI Deep Color
Audio
Speaker Setting
Musical Auto Calibration
EQ Optimizer
HDMI Audio
Digital Output
Dynamic Range Control
AV Sync
System
Initial Settings
Internet@TV Screen Size
Anynet+(HDMI-CEC)
BD Data Management
Clock
DivX(R) Registration
DivX(R) Deactivation
Network Setup
Network Settings
Network Status
BD-LIVE Internet Connection
Language
Security
Parental Rating
Change Password
2
7
17
29
ENGLISH
2
3
4
4
4
English
Contents
Setup
43
43
43
43
43
44
44
44
General
Background
Energy Saving
Front Display
Power On/Off Sound
Support
Software Upgrade
Contact Samsung
Basic Functions
45
45
46
47
47
48
50
52
53
54
54
55
Playing a Disc
Using the Disc menu / Title menu / Popup menu
Using the Search and Skip Functions
Slow Motion Play/Step Motion Play
Repeat Playback
Using the TOOLS button
Listening to Music
Sound Mode
Playing back a Picture
Playing back a USB Storage
Listening to Radio
Using an iPod
Network Services
57
61
61
61
Using Internet@TV
BD-LIVE™
Software Upgrade Notification
Using the AllShare Function
Other Information
63
66
Troubleshooting
Specifications
43
45
57
63
• Figures and illustrations in this User Manual are provided for reference only and may differ from actual product appearance.
English
01
Getting Started
Getting Started
Icons that will be used in manual
Make sure to check the following terms before reading the user manual.
Term
Logo
Icon
h
�
Z
BD-ROM
BD-RE/-R
DVD-VIDEO
Definition
This involves a function available on a BD-ROM.
This involves a function available on a BD-RE/-R disc recorded in the
BD-RE format.
This involves a function available on a DVD-VIDEO.
DVD-RW(V)
DVD-R
�
DVD+RW
This involves a function available on recorded DVD+RW or DVD-RW(V)/
DVD-R/+R discs that have been recorded and finalised.
DVD+R
MP3
WMA
-
JPEG
-
o
�
G
DivX
MKV
MP4
DivX
�
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing DivX contents.
F
!
✎
This involves a function available on a USB storage device.
Audio CD
USB storage
device
-
CAUTION
-
NOTE
-
Shortcut Key
-
This involves a function available on an audio CD-RW/-R (CD-DA format).
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing MP3 or WMA contents.
This involves a function available in a CD-RW/-R, DVD-RW/-R disc or a
USB storage media containing JPEG contents.
This involves a situation where a function does not operate or settings may
be cancelled.
This involves tips or instructions on the page that help each function
operate.
This function provides direct and easy access pressing the button on
the remote control.
• This product is compatible with the PAL colour system only.
• NTSC discs will not play.
English
Getting Started
Disc Types and Characteristics
Logos of Discs that can be played
Blu-ray Disc Compatibility
Blu-ray is a new and evolving format. Accordingly, disc
compatibility issues are possible. Not all discs are
compatible and not every disc will play back. For
additional information, refer to the Disc Types and
Characteristics section of this Manual. If you encounter
compatibility problems, please contact the SAMSUNG
customer care centre.
✎ NOTE
 Playback may not work for some types of discs, or
when specific operations, such as angle change
and aspect ratio adjustment, are being performed.
Information about the discs is written in detail on
the box. Please refer to this if necessary.
 Do not allow the disc to become dirty or scratched.
Fingerprints, dirt, dust, scratches or deposits of
cigarette smoke on the recording surface may
make it impossible to use the disc for playback.
 When a BD-Java title is played, loading may take
longer than a normal title, or some functions may
perform slowly.
Blu-ray Disc
Dolby Digital Plus
PAL broadcast system in
U.K, France, Germany, etc.
Dolby TrueHD
DTS-HD High Resolution
Audio
Java
DTS-HD Master Audio |
Essential
BD-LIVE
Discs that cannot be played
HD DVD Disc
DVD-RAM
3.9 GB DVD-R Disc for Authoring.
DVD-RW(VR mode)
Super Audio CD(except CD layer)
DVD-ROM/PD/MV-Disc, etc CVD/CD-ROM/
CDV/CD-G/CD-I/LD
• CDGs play audio only, not graphics.
•
•
•
•
•
•
✎ NOTE
 Some commercial discs and DVD discs purchased
outside your region may not be playable with this
product. When these discs are played, either “No
disc.” or “Please check the regional code of the
disc.” will be displayed.
 If a DVD-R/-RW disc has not been recorded properly
in DVD video format, it will not be playable.
English
01
Disc Types
Both the product and the discs are coded by
region. These regional codes must match in
order to play the disc. If the codes do not match,
the disc will not play.
BD-ROM
Disc Type
Blu-ray
DVD-VIDEO
Region
Code
Area
a
North America, Central America,
South America, Korea, Japan,
Taiwan, Hong Kong and South
East Asia.
b
Europe, Greenland, French
territories, Middle East, Africa,
Australia and New Zealand.
c
India, China, Russia, Central and
South Asia.
1
The U.S., U.S. territories and
Canada
2
Europe, Japan, the Middle East,
Egypt, South Africa, Greenland
3
Taiwan, Korea, the Philippines,
Indonesia, Hong Kong
4
Mexico, South America, Central
America, Australia, New Zealand,
Pacific Islands, Caribbean
5
Russia, Eastern Europe, India,
most of Africa, North Korea,
Mongolia
6
China
Blu-ray Disc Read Only Memory. A BD-ROM disc
contains pre-recorded data. Although a BD-ROM
may contain any form of data, most BD-ROM discs
will contain movies in High Definition format, for
playback on the product. This product can play
back pre-recorded commercial BD-ROM discs.
BD-RE/BD-R
Blu-ray Disc Rewritable/Blu-ray Disc Recordable.
BD-RE/BD-R is the ideal format for making
backups, or recording personal video.
DVD-VIDEO
• A digital versatile disc (DVD) can contain up to 135minutes of images, 8 audio languages and 32 subtitle
languages. It is equipped with MPEG-2 picture
compression and Dolby Digital surround, allowing you
to enjoy vivid and clear quality images.
• When switching from the first layer to the second
layer of a dual-layered DVD Video disc, there may
be momentary distortion in the image and sound.
This is not a malfunction of the product.
• Once a DVD-RW/-R recorded in Video Mode is
finalised, it becomes DVD-Video. Pre-recorded
(pre-stamped) commercial DVDs with movies are
also referred to as DVD-Videos. This product can
play back pre-recorded commercial DVD discs
(DVD-Video discs) with movies.
DVD-R/-RW
• Once a DVD-R/-RW recorded in Video Mode is
finalised, it becomes DVD-Video. Ability to play
back may depend on recording conditions.
• This product can play back DVD-R disc recorded
and finalised with a Samsung DVD video recorder.
• Playback can be perfomed with DVD-RW discs in
the Video Mode and finalised only.
DVD+RW
• This product can play back a DVD+RW disc
recorded with a DVD Video recorder. Ability to
play back may depend on recording conditions.
DVD+R
• This product can play back a DVD+R disc recorded
and finalised with a DVD Video recorder. Ability to
play back may depend on recording conditions.
English
Getting Started
Region code
Getting Started
Audio CD
DivX(Digital Video Express)
• An audio disc on which 44.1kHz PCM Audio is
recorded.
• This product can play back CD-DA format audio
CD-R and CD-RW discs.
• The product may not be able to play some CD-R or
CD-RW discs due to the condition of the recording.
DivX is a video file format developed by Microsoft and is
based on MPEG4 compression technology to provide
audio and video data over the Internet in real-time.
MPEG4 is used for video encoding and MP3 for audio
encoding so that the users can watch a movie at near
DVD-quality video and audio.
CD-R/-RW
Supported Formats(DivX)
• Use a 700MB(80 minutes) CD-R/-RW disc.
If possible, do not use a 800MB(90 minutes) or above
disc, as the disc may not play back.
• If the CD-R/-RW disc was not recorded as a closed
session, you may experience delays when playing
back the beginning of the disc or all recorded files
may not play.
• Some CD-R/-RW discs may not be playable with this
product, depending on the device which was used to
burn them. For contents recorded on CD-R/-RW
media from CDs for your personal use, playability
may vary depending on contents and discs.
This product only supports the following media formats.
If both video and audio formats are not supported, the
user may experience problems such as broken images
or no sound.
Disc Format
Using MP3 disc
• CD-R/-RW, DVD-RW/-R recorded with UDF,
ISO9660 or JOLIET format can be played back.
• Only MP3 files with the “.mp3” or “.MP3” extension
can be played.
• Playable bit rate range is from 56 Kbps to 320 Kbps.
• Playable sample-rate is 32KHz to 48KHz.
• The product can handle a maximum of 1500 files and
folders under a parent folder. For MP3 files recorded with
a VBR(Variable Bit Rates), the sound may cut in and out.
Using JPEG disc
• CD-R/-RW, DVD-RW/-R recorded with UDF,
ISO9660 or JOLIET format can be played back.
• Only JPEG files with the ".jpg", ".JPG", ".jpeg" or
"JPEG" extension can be displayed.
• Progressive JPEG is supported.
DVD-RW/-R (V)
• This is a format that is used for recording data on a
DVD-RW or DVD-R disc. The disc can be played by
this product once it has been finalised.
• If a disc that has been recorded in Video Mode by a
different maker’s recorder but has not been finalised,
it cannot be played by this product.
10
English
Supported Video Formats
Format
AVI
Supported Versions
DivX3.11~DivX5.1, XviD
Supported Audio Formats
Format
Bit Rate
Sampling
Frequency
MP3
80~384kbps
44.1khz
AC3
128~384kbps
44.1/48khz
DTS
1.5Mbps
44.1khz
• DivX files, including audio and video files, created
in the DTS format can only support up to 6Mbps.
• Aspect Ratio : Although the default DivX resolution
is 640x480 pixels (4:3), this product supports up
to 800x600 pixels (16:9). TV screen resolutions
higher than 800 will not be supported.
• When you play a disc whose sampling frequency is
higher than 48khz or 320kbps, you may experience
shaking on the screen during playback.
• Qpel and gmc is not supported.
MKV, MP4
• CD-R/-RW, DVD-R/-RW, USB, PC streaming
• Video Files with the following extensions can be
played. : .avi, .divx, .mkv, .mp4, .AVI, .DIVX,
.MKV, .MP4
✎ NOTE
 Some DivX, MKV and MP4 format discs may
not play, depending on the video resolution and
frame rate condition.
01
Video File Support
File Extension
Container
*.avi
Video Codec
Audio Codec
Resolution
Divx 3.11/4.x/5.1/6.0
MP3
AC3
DTS
WMA
PCM
1920x1080
XviD
AVI
MP4v3
H.264 BP/MP/HP
1920x1080
1920x1080
1920x1080
1920x1080
VC-1 AP(wmv1)
*.mkv
DivX 5.1/6.0
MKV
XviD
MP3
AC3
DTS
1920x1080
1920x1080
1920x1080
H.264 BP/MP/HP
*.wmv
WMV
*.mp4
MP4
*.mpg
*.mpeg
PS
VC-1 AP
1920x1080
WMA
VC-1 SM
MP4 (mp4v)
H.264 BP/MP/HP
MPEG1
MPEG2
H.264 BP/MP/HP
1920x1080
1920x1080
AAC
1920x1080
1920x1080
MP1, 2
AC3
DTS
1920x1080
1920x1080
Music File Support
File Extension
Container
Audio Codec
Support Range
*.mp3
MP3
MP3
-
WMA
Compliant with WMA version 10
* Sampling rates (in kHz) - 8, 11, 16, 22, 32,
44.1, 48
* Bit rates - All bit-rates in the range 5kbps to
384kbps
*.wma
WMA
English
11
Getting Started
Supported File Formats
Getting Started
USB Host Specification
USB Host Specification
• Supports USB 1.1 or USB 2.0 compliant devices.
• Supports devices connected using the USB
A type cable.
• Supports UMS (USB Mass Storage Device)
V1.0 compliant devices.
• Supports FAT(FAT, FAT16, FAT32) file
system formatting.
Non-compliance
• Does not support a device that requires installing
a separate driver on the PC (Windows).
• Does not support connection to a USB hub.
• A USB device that is connected using an
USB extension cable may not be recognized.
Operational Limitations
• If the connected device has multiple drives
(or partitions) installed, only one drive
(or partition) can be connected.
• A device supporting USB 1.1 alone may
cause a difference in the picture quality,
depending on the device.
Supported file Formats
Format
Still Picture
Music
File name
File extension
Bit rate
Version
Pixel
Sampling Frequency
JPG
JPG .JPEG
–
–
640x480
–
MP3
.MP3
80~384kbps
–
–
44.1kHz
• CBI (Control/Bulk/Interrupt) is not supported.
• Digital Cameras that use PTP protocol or
require additional program installation when
connected to a PC are not supported.
• A device using the NTFS file system is not
supported. (Only the FAT 16/32 (File Allocation
Table 16/32) file system is supported.)
• Does not operate with Janus enabled MTP
(Media Transfer Protocol) devices.
USB Devices that can be used with the
product
1. USB Storage Device
2. MP3 Player
3. Digital Camera
4. Removable HDD
• Removable HDDs equipped with less than 160
Gbytes are supported. Removable HDDs
equipped with 160Gbytes or more may not be
recognized, depending on the device.
• If the connected device does not work due to
insufficient power supply, you can use a
separate power cable to supply power so that it
can work properly. The USB cable connector
may differ, depending on the manufacturer of
the USB device.
5. USB card Reader: One slot USB card reader and
Multi-slot USB card reader.
• The USB card reader may not be supported,
depending on the manufacturer.
• If you install multiple memory devices into a
multi-card reader, you may experience
problems.
Accessories
Check for the supplied accessories below.
FUNCTION
TV SOURCE
POWER
BD RECEIVER/TV
SLEEP
1
2
4
5
7
8
FULL SCREEN
3
6
9
REPEAT
0
MUTE
VOL
TUNING
/CH
SFE MODE
DISC MENU
MENU
TITLE MENU
POPUP
TOOLS
INFO
RETURN
EXIT
TUNER
MEMORY
A
INTERNET@
Video Cable
12
English
FM Antenna
iPod Dock
User's Manual
B
C
MO/ST
D
DSP
Remote Control/
Batteries (AAA size)
ASC Microphone
HDMI Cable
01
Front Panel
2
1
3
4
5
6
7
8
9
10
11
12
13
ASC IN
1
2
3
4
5
POWER BUTTON (
6
FUNCTION BUTTON
7
TUNING DOWN & SKIP BUTTON
8
9
STOP BUTTON
Stops disc playback.
PLAY/PAUSE BUTTON
Plays a disc or pauses playback.
10
TUNING UP & SKIP BUTTON
Goes to the next title/chapter/track.
Tunes up the FM frequency band.
11
VOLUME CONTROL
Volume adjustment.
12
USB PORT
A USB storage device can be connected here and used as storage when connected to BDLIVE. It can also be used for software upgrades and MP3/JPEG/DivX/MKV/MP4 playback.
13
ASC IN JACK
Used to connect the ASC Microphone for setting up MAC(Musical Auto Calibration).
)
Turns the product on and off.
DISC TRAY
Insert disc here.
REMOTE CONTROL SENSOR
Detects signals from the remote control.
DISPLAY
Displays the playing status, time, etc.
OPEN/CLOSE BUTTON
Opens and closes the disc tray.
The mode switches as follows :
BD/DVD ; D. IN ; AUX ; HDMI 1 ; HDMI 2 ; FM
Goes back to the previous title/chapter/track.
Tunes down the FM frequency band.
✎ NOTE
 Software upgrades using the USB Port must be performed with a USB memory flash stick only.
 A USB device consuming more than 500mA requires a separate power supply device for normal operation.
 A USB HDD device cannot be used for BD Data storage (BD-LIVE).
English
13
Getting Started
Description
Getting Started
Rear Panel
1
2
3
4
5
6
7
8
9 10 11
FM ANT.
LAN
WIRELESS
DIDITAL
AUDIO IN
HDMI IN
12
13
COMPONENT OUT
HDMI OUT
iPod
OPTICAL
SPEAKER IMPEDANCE : 3
WIRELESS LAN
AUX
VIDEO OUT
1
5.1 CHANNEL SPEAKER OUTPUT
CONNECTORS
Connect the front, centre, surround, subwoofer speakers.
(HT-C5530W/C5550W do not have surround speaker connectors on
the product, the surround speakers are connected to the Wireless
Receiver module.)
2
COOLING FAN
The cooling fan supplies cool air to the product to prevent overheating
and always revolves when the power is on.
3
iPod JACK
Connect the iPod dock connector here.
4
FM 75Ω COAXIAL JACK
Connect the FM antenna.
5
TX CARD CONNECTION (WIRELESS)
The TX card enables communication between the product and the
wireless receiver module.
(The wireless receiver module is not provided for HT-C5500 )
6
EXTERNAL DIGITAL OPTICAL IN JACKS
(OPTICAL)
Use this to connect external equipment capable of digital output.
7
HDMI IN JACKS
Receives digital video and audio signals simultaneously using an
HDMI cable.
8
HDMI OUT JACK
Use an HDMI cable, connect this HDMI output terminal to the HDMI
input terminal on your TV for the best quality picture.
9
WIRELESS LAN JACK
Can be used for network based services (see pages 57~62),
BD-LIVE and software upgrade with a wireless LAN adapter.
10
LAN TERMINAL
Can be used for network based services (see pages 57~62),
BD-LIVE and software upgrade under the network connection.
11
AUX IN JACKS
Connect to the 2CH analogue output of an external device
(such as a VCR)
12
COMPONENT VIDEO OUT JACKS
Connect a TV with Component video inputs to these jacks.
13
VIDEO OUT JACK
Connect your TV's Video Input jack (VIDEO IN) to the VIDEO OUT
Jack on this product.
! CAUTION
 Ensure a minimum of 10 cm of clear space on all sides of the cooling fan when installing the product.
 Do not obstruct the cooling fan or ventilation holes.
14
English
01
Getting Started
Remote control
Tour of the Remote Control
POWER
FUNCTION
TV SOURCE
BD RECEIVER/TV
SLEEP
Turn the product on and off.
Press to select BD RECEIVER/TV
mode.
Press numeric buttons to operate options.
2
3
4
5
6
7
8
9
REPEAT
0
Press this to see the full screen on a TV.
Allows you to repeat a title, chapter,
track or disc.
Press to search backwards or
forwards.
Press to skip backwards or forwards.
Press to pause a disc.
Press to stop/play a disc.
Cut off the sound temporarily.
MUTE
Adjust the volume.
VOL
TUNING
/CH
SFE MODE
DISC MENU
MENU
TITLE MENU
Press to view the disc menu.
Press this to use the Tools menu.
POPUP
TOOLS
INFO
RETURN
EXIT
Select on-screen menu items and
change menu value.
Return to the previous menu.
These buttons are used both for menus
on the product and also several
Blu-ray Disc functions.
Press this to link to various
Internet@TV services.
Select the desired Dolby Pro
Logic II audio mode.
Set a Sleep time to shut off the
procuct.
To open and close the disc tray.
1
FULL SCREEN
Press this to move to the home
menu.
This is mode selection button.
or
Press to select TV's video mode.
Search for active FM stations and
change channels.
You can set the SFE(Sound Field
Effect) mode best suited for the
type of music you are listening to.
Use this to enter the popup
menu/title menu.
Use this to display the playback
information when playing
a Blu-ray/DVD disc.
Press this to exit the menu.
TUNER
MEMORY
A
INTERNET@
B
C
MO/ST
D
DSP
Used to set a preset radio
frequency.
Select MONO or STEREO for radio
broadcasting.
Regulate and stabilize the volume
level. (Digital Signal Processor)
English
15
Getting Started
Installing batteries in the Remote Control
* Battery size: AAA
✎ NOTE
 Make sure to match the “+” and “–” ends of
TV Brand Code List
Brand
Code
Brand
Code
Admiral
(M.Wards)
56, 57, 58
Mitsubishi/
MGA
18, 40, 59, 60, 75
A Mark
01, 15
MTC
18
NEC
18, 19, 20, 40, 59, 60
Anam
01, 02, 03, 04, 05,
06, 07, 08, 09, 10,
11, 12, 13, 14
Nikei
03
Onking
03
AOC
01, 18, 40, 48
Bell &
Howell
(M.Wards)
57, 58, 81
Brocsonic
59, 60
Candle
18
Onwa
03
Panasonic
06, 07, 08, 09, 54,
66, 67, 73, 74
Penney
18
Philco
03, 15, 17, 18, 48,
54, 59, 62, 69, 90
Cetronic
03
Citizen
03, 18, 25
Philips
15, 17, 18, 40,
48, 54, 62, 72
Cinema
97
Pioneer
63, 66, 80, 91
Classic
03
Portland
15, 18, 59
Concerto
18
Proton
40
Contec
46
Quasar
06, 66, 67
Coronado
15
Craig
03, 05, 61, 82, 83, 84
Radio
Shack
17, 48, 56, 60,
61, 75
Croslex
62
Crown
03
RCA/
Proscan
18, 59, 67, 76, 77,
78, 92, 93, 94
Curtis
Mates
Realistic
03, 19
59, 61, 63
CXC
03
When operating a TV with the remote control
Daewoo
02, 03, 04, 15, 16,
17, 18, 19, 20, 21,
22, 23, 24, 25, 26,
27, 28, 29, 30, 32,
34, 35, 36, 48, 59, 90
1. Press the BD RECEIVER/TV button to set the
remote control to TV mode.
Daytron
40
Dynasty
03
Emerson
03, 15, 40, 46, 59, 61,
64, 82, 83, 84, 85
Fisher
19, 65
the batteries with the diagram inside the
compartment.
 Assuming typical TV usage, the batteries last
for about one year.
 The remote control can be used up to
approximately 7 meters in a straight line.
Setting the Remote Control
You can control certain functions of your TV with
this remote control.
2. Press the POWER button to turn on the TV.
3. While holding down the POWER button, enter
the code corresponding to your brand of TV.
• If there is more than one code listed for
your TV in the table, enter one at a time to
determine which code works.
• Example : For a Samsung TV
While holding down the POWER button, use the
number buttons to enter 00, 15, 16, 17 and 40.
4. If the TV turns off, the setting is complete.
• You can use the TV POWER, VOLUME,
CHANNEL, and Numeric buttons (0~9).
✎ NOTE
 The remote control may not work on some
brands of TV's. Also, some operations may not
be possible, depending on your brand of TV.
 The remote control will work with Samsung TVs
by default.
16
English
Funai
03
Futuretech
03
General
Electric (GE)
06, 40, 56, 59,
66, 67, 68
Hall Mark
40
Hitachi
15, 18, 50, 59, 69
Inkel
45
JC Penny
56, 59, 67, 86
JVC
70
KTV
59, 61, 87, 88
KEC
03, 15, 40
KMC
15
LG
(Goldstar)
01, 15, 16, 17, 37, 38,
39, 40, 41, 42, 43, 44
Sampo
40
Samsung
00, 15, 16, 17, 40,
43, 46, 47, 48, 49,
59, 60, 98
Sanyo
19, 61, 65
Scott
03, 40, 60, 61
Sears
15, 18, 19
Sharp
15, 57, 64
Signature
2000
(M.Wards)
57, 58
Sony
50, 51, 52, 53, 55
Soundesign
03, 40
Spectricon
01
SSS
18
Sylvania
18, 40, 48, 54,
59, 60, 62
Symphonic
61, 95, 96
Tatung
06
Techwood
18
Teknika
03, 15, 18, 25
TMK
18, 40
Toshiba
19, 57, 63, 71
Vidtech
18
Videch
59, 60, 69
Luxman
18
Wards
LXI
(Sears)
19, 54, 56, 59,
60, 62, 63, 65, 71
15, 17, 18, 40,
48, 54, 60, 64
Yamaha
18
Magnavox
15, 17, 18, 48, 54,
59, 60, 62, 72, 89
York
40
Yupiteru
03
Marantz
40, 54
Zenith
58, 79
Matsui
54
Zonda
01
MGA
18, 40
Dongyang
03, 54
02
Connections
Connections
This section involves various methods of connecting the product to other external components.
Before moving or installing the product, be sure to turn off the power and disconnect the power cord.
Connecting the Speakers
Position of the product
SW
Place it on a stand or cabinet shelf, or under the
TV stand.
Selecting the Listening Position
The listening position should be located about 2.5
to 3 times the distance of the TV's screen size
away from the TV.
Example : For 32" TV's 2~2.4m
For 55" TV's 3.5~4m
Front Speakers ei
Place these speakers in front of your listening position, facing inwards (about 45°)
toward you. Place the speakers so that their tweeters will be at the same height
as your ear. Align the front face of the front speakers with the front face of the
centre speaker or place them slightly in front of the centre speakers.
Centre Speaker f
It is best to install it at the same height as the front speakers. You can also install it
directly over or under the TV.
Surround Speakershj
Subwoofer g
Place these speakers to the side of your listening position. If there isn't enough
room, place these speakers so they face each other. Place them about 60 to
90cm above your ear, facing slightly downward.
Unlike the front and centre speakers, the surround speakers are used to
* handle
mainly sound effects and sound will not come from them all the time.
The position of the subwoofer is not so critical. Place it anywhere you like.
! CAUTION
 Do not let children play with or near the speakers. They could get hurt if a speaker falls.
 When connecting the speaker wires to the speakers, make sure that the polarity (+/­–) is correct.
 Keep the subwoofer speaker out of reach of children so as to prevent children from inserting their hands or alien substances
into the duct (hole) of the subwoofer speaker.
 Do not hang the subwoofer on the wall through the duct (hole).
✎ NOTE
 If you place a speaker near your TV set, screen colour may be distorted because of the magnetic field generated by the
speaker. If this occurs, place the speaker away from your TV set.
English
17
Connections
Speaker Components
HT-C5500
(L)
(R)
(L)
FRONT
(R)
CENTRE
SURROUND
Speaker Components
SUBWOOFER
SPEAKERCABLE
Assembled Speakers
HT-C5530W
(L) (R)
HT-C5530W
SCREW (Large): 2EA
CENTRE SPEAKER
SCREW (Small): 8EA
FRONT
(L)
STAND
CENTRE
(R)

SURROUND
SPEAKER
SURROUND
STANDBASE
FRONT SPEAKER
SUBWOOFER
SUBWOOFER
SPEAKERCABLE
HT-C5550W
(L) (R)
HT-C5550W
SCREW (Large): 4EA
SCREW (Small): 16EA
FRONT
STAND
(L) (R)
CENTRE
SURROUND
CENTRE SPEAKER
STANDBASE
SUBWOOFER

FRONT/SURROUND SPEAKER
SPEAKERCABLE
✎ NOTE
 Refer to page 19 to install the Speakers on the Tallboy Stand.
1
English
SUBWOOFER
02
Connections
Installing the Speakers on the Tallboy Stand
* HT-C5530W only
* HT-C5550W only
1. Turn the Stand Base upside-down and connect it to the Stand.
1
Stand
Base
Stand
2. Insert four small screws clockwise into the four holes marked using a
screwdriver as shown in the illustration.
3. Connect the upper Speaker to the assembled Stand.
2
3
Speaker
Stand
4. Insert another large screw clockwise into the hole on the rear of the
speaker using a screwdriver.
4
English
1
Connections
Connecting the Speakers
Connecting The Speakers
* HT-C5500 only
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into the
red terminal (+), and then release the tab.
3. Connect the connecting plugs to the back of the product by matching
the colours of the speaker plugs to the speaker jacks.
Black
Red
HT-C5500
Front Speaker (L)
Centre Speaker
Subwoofer
Front Speaker (R)
SPEAKER IMPEDANCE : 3
Surround Speaker (L)
Surround Speaker (R)
FM ANT
WIRELESS
iPod
SPEAKER IMPEDANCE : 3
✎ NOTE
 HT-C5530W/C5550W do not have surround speaker connectors on the main unit.
The surround speakers are connected to the Wireless Receiver Module. See pages 21~22.
 The surround speakers for HT-C5500 can also be connected to the Wireless Receiver Module
(SWA-5000) if you purchase it separately. See pages 21~22.
0
English
02
Connections
* HT-C5530W only
* HT-C5550W only
Wireless Receiver Module : SWA-5000
TX Card
Wireless Receiver Module
Speaker Cable (2EA)
✎ NOTE
 This product should be connected with the SWA-5000 only.
In case of HT-C5530W
Centre Speaker
Surround
Speaker (L)
Surround
Speaker (R)
Subwoofer
SPEAKER IMPEDANCE : 3
Wireless Receiver Module
FM ANT.
WIRELESS
IPOD
SPEAKER IMPEDANCE : 3
Front Speaker (R)
Front Speaker (L)
Refer to page 18 for the HT-C5550W speaker.
English
1
Connections
1. Press down the terminal tab on the back of the speaker.
2. Insert the black wire into the black terminal (–) and the red wire into the red
terminal (+), and then release the tab.
3. Connect the connecting plugs to the back of the product by matching the
colors of the speaker plugs to the speaker jacks.
Black
Red
4. With the product turned off, insert the TX card into the
TX Card Connection (WIRELESS) on the back of the product.
• Hold the TX card so that the label "WIRELESS" faces upward
and insert the card into the port.
• The TX card enables communication between the product and
the wireless receiver module.
5. Connect the left and right surround speakers to the wireless Receiver
module.
FM ANT.
WIRELESS
DIDITAL
AUDIO IN
iPod
6. Plug the power cord of the wireless Receiver module in the wall
outlet .
OPTICAL
TX card
✎ NOTE
 The surround speakers for HT-C5500 can also be connected to the
Wireless Receiver Module (SWA-5000) if you purchase it separately.
 Place the wireless receiver module at the rear of the listening position. If the wireless receiver module is
too close to the product, some sound interruption may be heard due to interference.
 If you use a device such as a microwave oven, wireless LAN Card or any other device that uses
the same frequency (2.4/5.8GHz) near the product, some sound interruption may be heard due
to interference.
 The transmission distance from the product to the wireless receiver module is about 10m, but may
vary depending on your operating environment. If a steel-concrete wall or metallic wall is between
the product and the wireless receiver module, the system may not operate at all, because the radio
wave cannot penetrate metal.
 If the product doesn't make wireless connection, the system needs ID Setting between the
product and wireless receiver module. With the product turned off, press the remote control's
number buttons "0""1""3""5" and turn on the product. With the wireless receiver module
turned on, press "ID SET" button on the back of the wireless receiver module for 5 seconds.
! CAUTION
 Do not insert any other card except the TX card dedicated to the product.
If a different TX card is used, the product may be damaged or the card may not be removed easily.
 Do not insert the TX card upside down or in the reverse direction.
 Insert the TX card when the product is turned off. Inserting the card when it is turned on may
cause a problem.
 If the TX Card is inserted and wireless receiver module setting is complete, sound is not output
from the Surround Speaker connectors on the product.
 The wireless receiving antenna is built into the wireless receiver module. Keep it away from water
and moisture.
 For optimal listening performance, make sure that the area around the wireless receiver module
location is clear of any obstructions.
 If no sound is heard from the wireless surround speakers, switch the mode to DVD 5.1
channel or Dolby Pro Logic II.
 In 2-CH mode, no sound will be heard from the wireless surround speakers.
English
02
HDMI is a standard digital interface for connection to such devices as a TV, projector, DVD player, Blu-ray
player, set top box and more.
HDMI removes any loss of signal from analogue conversion, enabling you to enjoy video and audio sound
quality as it was originally created in the digital source.
DVD or Blu-ray Player
SAT(Satellite/Set top box)
HDMI IN
HDMI OUT
HDMI OUT : Connecting to a TV with an HDMI Cable (BEST QUALITY)
Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on
your TV.
✎ NOTE
 Certain HDMI output resolutions may not work, depending on your TV.
 If an HDMI cable is connected or removed during playback of a CD-DA, MP3 or JPEG file, the product will
stop playing.
 After making the video connection, set the Video input source on your TV to match the corresponding Video
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
 If you have set the product's remote control to operate your TV, press the SOURCE button on the remote
control and select HDMI as the external source of the TV.
English
Connections
Connecting external Devices/your tv via HDmI
Connections
HDMI IN : Connecting to an External Component with an HDMI Cable
1. Connect an HDMI cable from the HDMI IN jack on the back of the product to the HDMI OUT jack
on your digital devices.
2. Press the FUNCTION button to select HDMI 1 or HDMI 2 input.
The mode switches as follows : BD/DVD ; D. IN ; AUX ; HDMI 1 ; HDMI 2 ; FM
HDMI Auto Detection Function
The product's video output will automatically change to HDMI mode when connecting an HDMI cable
before power is on. For possible HDMI resolutions, see page 32.
• This function is not available if the HDMI cable does not support CEC.
• HDMI connection description
- HDMI outputs only a pure digital signal to the TV.
- If your TV does not support HDCP, random noise appears on the screen.
• What is the HDCP?
HDCP (High-band width Digital Content Protection) is a system for protecting BD/DVD content outputted via
HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display
device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being
made.
! CAUTION
 The Anynet+ function is supported only when an HDMI Cable is connected to the HDMI OUT of the
product.
English
02
Connections
Connecting the video out to your tv
Red
LAN
Blue
Green
METHOD 1
COMPONENT OUT
HDMI OUT
METHOD 2
Yellow
WIRELESS LAN
AUX IN
VIDEO OUT
METHOD 1 : Component Video (BETTER QUALITY)
If your television is equipped with Component Video inputs, connect a Component video cable (not
supplied) from the Component Video Output (Pr, Pb and Y) Jacks on the back of the product to the
Component Video Input Jacks on your TV.
✎ NOTE
 You can select from a variety of resolution settings such as 1080i, 720p, 576p(480p) and 576i(480i),
depending on the disc type. (See page 32)
 The actual resolution may differ from the setting in the Setup menu if both Component and HDMI cables are
connected. The resolution may also be different depending on the disc. (See page 32)
 After making the video connection, set the Video input source on your TV to match the corresponding Video
output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
 If you have set the product's remote control to operate your TV, press the TV SOURCE button on the remote
control and select COMPONENT as the external source of the TV.
 In DVD playback, if both HDMI and Component jacks are connected and you select the Component 1080p,
1080i, 720p or 576p(480p) mode, the Display Setup menu will show the output resolution as 1080p, 1080i,
720p or 576p(480p) in the menu. The resolution is actually 576i(480i).
METHOD 2 : Composite Video (GOOD QUALITY)
Connect the supplied Video cable from the VIDEO OUT jack on the back of the product to the VIDEO
IN jack on your TV.
✎ NOTE
 The VIDEO source is always output in 576i(480i) resolution regardless of the resolution set in the Setup
menu. (See page 32)
 After making the video connection, set the Video input source on your TV to match the corresponding
Video output (HDMI, Component or Composite) on your product.
See your TV owner's manual for more information on how to select the TV's Video Input source.
 If you have set the product's remote control to operate your TV, press the TV SOURCE button on
the remote control and select VIDEO as the external source of the TV.
! CAUTION
 Do not connect the unit through a VCR. Video signals fed through VCRs may be affected by
copyright protection systems and the picture will be distorted on the television.
English
Connections
Connecting audio from external Components
LAN
DIDITAL
AUDIO IN
WIRELESS
HDMI IN
COMPONENT OUT
HDMI OUT
OPTICAL
AUX
WIRELESS LAN
Optical Cable
(not supplied)
Set-Top Box
OPTICAL
Red
VIDEO OUT
White
Audio Cable
(not supplied)
If the external analogue
component has only one
Audio Out, connect either
left or right.
VCR
AUX
OPTICAL : Connecting an External Digital Component
Digital signal components such as a Cable Box/Satellite receiver (Set-Top Box).
1. Connect the Digital Input (OPTICAL) on the product to the Digital Output of the external digital
component.
2. Press the FUNCTION button to select D.IN input.
• The mode switches as follows : BD/DVD ; D. IN ; AUX ; HDMI 1 ; HDMI 2 ; FM
✎ NOTE
 To see video from your Cable Box/Satellite receiver, you must connect it's video output to a TV.
 This system supports Digital sampling frequencies of 32 kHz of higher from external digital components.
 This system supports only DTS and Dolby Digital audio, MPEG audio which is bitstream cannot be supported.
AUX : Connecting an External Analogue Component
Analogue signal components such as a VCR.
1. Connect AUX IN (Audio) on the product to the Audio Out of the external analogue component.
• Be sure to match connector colours.
2. Press the FUNCTION button to select AUX input.
• The mode switches as follows : BD/DVD ; D. IN ; AUX ; HDMI 1 ; HDMI 2 ; FM
✎ NOTE
 You can connect the Video Output jack of your VCR to the TV, and connect the Audio Output jacks of
the VCR to this product.
English
02
This product enables you to view network based services (See pages 57~62) such as Internet@TV and
BD-LIVE, as well as receive software upgrades when a network connection is made. We recommend
using an AP (Access Point) or IP router for the connection.
For more information on router connection, refer to the user manual of the router or contact the router
manufacturer for technical assistance.
Cable Network
1. Using the Direct LAN Cable (UTP cable), connect the LAN terminal of the product to the LAN
terminal of your modem.
2. Set the network options. (See page 39)
LAN
DIDITAL
AUDIO IN
HDMI IN
COMPONENT OUT
HDMI OUT
OPTICAL
WIRELESS LAN
AUX
VIDEO OUT
Router
Broadband modem
(with integrated router)
Broadband
service
Or
Broadband modem
Broadband
service
Networking with PC for
AllShare function
(See pages 61~62)
✎ NOTE
 Internet access to Samsung’s software update server may not be allowed, depending on the router you use or the
ISP’s policy. For more information, contact your ISP (Internet Service Provider).
 For DSL users, please use a router to make a network connection.
 For the AllShare function, a PC must be connected in the network as shown in the figure.
English
Connections
Connecting to the network
Connections
Wireless Network
You can connect to the network with a Wireless IP sharer.
1. A wireless AP/IP router is required to make a wireless network connection. Connect the wireless
LAN adapter to the Wireless LAN Adapter on the rear panel of the product.
2. Set the network options. (See page 39)
Broadband
service
LAN
COMPONENT OUT
HDMI OUT
HDMI
OUT
WIRELESS LAN
Wireless IP sharer
AUX IN
VIDEO OUT
PC
Wireless LAN Adapter
(not included)
Networking with PC for
AllShare function
(See pages 61~62)
✎ NOTE
 This product is compatible with only Samsung's Wireless LAN Adapter. (not supplied) (Model name: WIS09ABGN).
- The Samsung Wireless LAN Adapter is sold separately. Contact a Samsung Electronics retailer for purchasing.
 You must use a wireless IP sharer that supports IEEE 802.11 a/b/g/n. (n is recommended for stable operation of the
wireless network.)
 Wireless LAN, by its nature, may cause interference, depending on the use condition (AP performance, distance, obstacles,
interference by other radio devices, etc).
 Set the wireless IP sharer to Infrastructure mode. Ad-hoc mode is not supported.
 When applying the security key for the AP (wireless IP sharer), only the following is supported.
1) Authentication Mode : WEP, WPAPSK, WPA2PSK
2) Encryption Type : WEP, TKIP, AES
 For the AllShare function, a PC must be connected in the network as shown in the figure.
Connecting the fm antenna
FM Antenna (supplied)
2. Slowly move the antenna wire around until
you find a location where reception is good,
then fasten it to a wall or other rigid surface.
FM ANT.
WIRELESS
iPod
English
1. Connect the FM antenna supplied to the FM
75Ω COAXIAL Jack.
✎ NOTE
 This product does not receive AM broadcasts.
03
Setup
1. Turn on your TV after connecting the product.
(When the product is connected to TV for the first
time, product will turn on automatically and the
Initial Settings screen will be displayed.)
Initial Settings I On-Screen Language
7. Press the ◄► buttons to the select the
desired Network Settings: Wired, Wireless or
PBC (WPS), then press the ENTER button.
(See pages 39~42)
The Network Test will start and Initial Settings
will be completed.
Initial Settings I Network
Select a language for the on-screen displays.
Network Setting is needed to use various Internet services.
Choose the primary method for connecting to network.
English
Français
Wired : Set the network by using Ethernet cable.
Deutsch
Please make sure that Ethernet cable is connected.
Español
Italiano
Wired
Nederlands
> Move
s Select
2. Press the ▲▼ buttons to select the desired
language, then press the ENTER button.
3. Press the ENTER button to select Start button.
Initial Settings
Wireless
PBC (WPS)
a Previous d Skip
< Move " Select
8. Press the OK button.
The home menu will be displayed. (For more
information about home menu, please see
page 30)
• Home Menu
TV Aspect, Musical Auto Calibration and Network will be set.
Each setting may be changed later under "Settings"
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
Start
a Previous
" Select
4. Press the ▲▼ buttons to select desired TV
Aspect ratio, then press the ENTER button.
(See page 31)
Musical Auto Calibration screen will be displayed.
5. Plug the ASC microphone into the ASC IN jack
on the product. (See page 35)
6. Press the ENTER button to select Start button.
Initial Settings I Musical Auto Calibration
Preparing...
d Skip
No Disc
a Change Device
d View Devices
" Enter
✎ NOTE
 When the product is connected to TV for the
first time, product will turn on automatically.
Do not confuse because this is not
malfunction.
 The home menu will not be displayed if you do
not configure the initial settings.
 If you press the BLUE(D) button during the
Musical Auto Calibration/Network setup, you
can access the home menu even if the
network setup is not completed yet.
 When you return to home menu, the full
screen mode will be cancelled automatically.
Setting the Musical Auto Calibration function
takes about 3 minutes.
English
Setup
Before Starting (Initial Settings)
Setup
 If you want to display Initial Settings screen
again in order to make changes,
press the
FUNCTION
TV SOURCE
STOP (@)POWER
button on the front
panel of the
product for more than 5 seconds with no disc
inserted.BD RECEIVER/TV
SLEEP
 Use the HDMI cable to connect the product to
an Anynet+(HDMI-CEC)-compliant Samsung TV.
If the TV uses
supported
by the
2
1 a language
3
product, that language will be set to a
preferred language
4
5automatically.
6
However, the Anynet+(HDMI-CEC) feature
should be 7
set to On8in both TV
9 and the
product.FULL SCREEN
REPEAT
 If the product is left0in the stop mode for more
than 5 minutes without being operated, a
screen saver will appear on your TV. If the
product is left in the screen saver mode for
more than 25 minutes, the power will
automatically turn off except during playback
MUTE
of a CD-DA (Automatic
Power-Off Function).
TUNING
VOL
/CH
SFE MODE
Setting
the menu
DISC MENU
MENU
POPUP
TOOLS
INFO
3
RETURN
A
4
EXIT
B
INIERNET @
Button
: Press
TUNER
MEMORY
MO/ST
C
D
this to
moveDSPto
the home menu.
1
MENU
2
RETURN Button : Return to the previous menu.
3
ENTER / DIRECTION Button:
Press the arrow buttons to move the cursor and select
an item.
Press the ENTER button to launch the selected item or
confirm the setting.
4
EXIT Button : Press this to exit the menu.
0
English
• Home Menu
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
2
3
4
1
5
No Disc
a Change Device
1
Selects the Internet@TV.
2
Selects the Videos.
3
Selects the Music.
4
Selects the Photos.
5
Selects the Settings.
6
Displays buttons available.
d View Devices
" Enter
6
TITLE MENU
1
2
1. Press the POWER button.
The Home Menu will appear.
2. Press the ◄► buttons to select Settings,
then press the ENTER button.
3. Press the ▲▼ buttons to select the desired
submenu, then press the ENTER button.
4. Press the ▲▼ buttons to select the desired
item, then press the ENTER button.
5. Press the EXIT button to exit the menu.
✎ NOTE
 When the product is connected to the network,
select Internet@TV from the home menu.
Download desired content from Samsung AppS.
 The access step may differ depending on the
selected menu.
 The OSD (On Screen Display) may change in
this product after upgrading the software
version.
03
You can configure various display options such as
the TV Aspect, Resolution, etc.
tv aspect
Depending on the type of television you have, you
may want to adjust the screen setting.
• 16:9 Normal
Certain movies(4:3 source)
will be displayed in 4:3
Pillarbox (black bars on sides
of picture) if 16:9 normal is
selected.
• 16:9 Wide
You can view the full 16:9
picture on your widescreen
TV.
• 4:3 Letter Box
Select when you want to see
the total 16:9 ratio screen
Blu-ray Disc/DVD supplies,
even though you have a TV
with a 4:3 ratio screen. Black
bars will appear at the top
and bottom of the screen.
• 4:3 Pan-Scan
Select when you want to see
the 16:9 video supplied by the
Blu-ray Disc/DVD without the
black bars on top and bottom,
even though you have a TV
with a 4:3 ratio screen(extreme
left and right portion of the
movie picture will be cut off).
✎ NOTE
 Depending on the disc type, some aspect ratios
may not be available.
 If you select an aspect ratio and option which is
different than the aspect ratio of your TV screen,
then the picture might appear to be distorted.
 If you select the 4:3 Pan-Scan or 4:3 Letter Box,
you can't see full screen by pressing the FULL
SCREEN button on the remote control.
 If you select the 16:9 Normal, 4:3 Pillarbox may be
displayed. In this case, you can't see full screen by
pressing the FULL SCREEN button on the remote control.
BD Wise (Samsung Products only)
BD Wise is Samsung's latest inter-connectivity feature.
When you connect Samsung products with
BD-Wise to each other via HDMI, the optimum
resolution will be set automatically.
• Off : The output resolution will be fixed
according to the Resolution previously set,
regardless of the resolution of the disc.
• On : The original resolution of the BD/DVD disc
will be output to the TV.
✎ NOTE
 If you want to change the resolution in BD
Wise, you must set BD Wise to Off in advance.
 If you set off the BD Wise, the resolution of the
connected TV will be adjusted to its maximum
resolution automatically.
 If the product is connected to a device that
does not support BD Wise, you can not use
BD Wise function.
 For a proper operation of BD Wise, set each BD Wise
menu of the product and the TV to On respectively.
Resolution
Sets the output resolution of the Component and
HDMI video signal.
The number in 1080p, 1080i, 720p, 576p(480p),
576i(480i) indicates the number of lines of video.
The i and p indicate interlace and progressive
scan, respectively.
• Auto : It automatically checks and sets the optimal
resolution. (HDMI only)
• BD Wise : Automatically sets the optimal
resolution when connected via HDMI to a TV with
the BD Wise feature. (The BD Wise menu item
appears only if BD Wise is set to On.) (HDMI only)
• 1080p : Outputs 1080 lines of progressive video. (HDMI only)
• 1080i : Outputs 1080 lines of interlaced video.
• 720p : Outputs 720 lines of progressive video.
• 576p/480p : Outputs 576(480) lines of progressive
video.
• 576i/480i : Outputs 576(480) lines of interlaced
video. (Component & VIDEO only)
English
1
Setup
Display
Setup
Resolution according to the output mode
• Blu-ray Disc playback
HDMI / connected
Output
Setup
HDMI / not connected
HDMI Mode
Component/VIDEO Mode
Component Mode
VIDEO Mode
Auto
Optimal Resolution
576i(480i)
-
-
1080p, Movie Frame(24Fs) off
1080p@60F
576i(480i)
-
-
1080p/1080i,
Movie Frame(24Fs) on
1080p@24F
576i(480i)
-
-
1080i, Movie Frame(24Fs) off
1080i
576i(480i)
1080i
576i(480i)
720p
720p
576i(480i)
720p
576i(480i)
576p(480p)
576p(480p)
576i(480i)
576p(480p)
576i(480i)
576i(480i)
-
-
576i(480i)
576i(480i)
• DVD playback
HDMI / connected
Output
Setup
HDMI / not connected
HDMI Mode
Component/VIDEO Mode
Component Mode
VIDEO Mode
Auto
Optimal Resolution
576i(480i)
-
-
1080p
1080p@60F
576i(480i)
-
-
1080i
1080i
576i(480i)
576p(480p)
576i(480i)
720p
720p
576i(480i)
576p(480p)
576i(480i)
576p(480p)
576p(480p)
576i(480i)
576p(480p)
576i(480i)
576i(480i)
-
-
576i(480i)
576i(480i)
✎ NOTE
 If the connected TV does not support Movie
Frame or the selected resolution, the message
“If no pictures are shown after the selection,
please wait for 15 seconds. And then, the
resolution will be reverted to the previous value
automatically. Would you like to make a
selection?” will be displayed.
If you select Yes and the resolution is not
supported, the TV's screen will be blank.
Please wait for 15 seconds and the resolution
will be reverted to the previous value
automatically.
 If the screen is blank, press and hold the
STOP (@) button on the front of the product
for more than 5 seconds (no disc inserted).
All settings are restored to the factory default.
Follow the steps on the previous page to
access each mode and select the Display
Setup that your TV will support.
32
English
 When the factory default settings are restored,
all the user data stored in the BD data will be
deleted.
 The Blu-ray Disc must have the 24 frame
feature in order to use the Movie Frame (24Fs)
mode.
 If both HDMI and Component jacks are
connected and you are currently viewing
component output, there is a difference
between resolution table and actual resolution
depending on your TV.
 If the HDMI Auto Detection feature does not
work, you can't select the 1080p resolution or
Movie Frame (24Fs).
03
Setup
HDMI Format
Progressive Mode
You can optimize the colour setting from the
HDMI output. Select a connected device Type.
Set to improve picture quality when viewing DVDs.
• TV : Select if connected to a TV via HDMI.
• Monitor : Select if connected to a Monitor via
HDMI.
✎ NOTE
 A TV or monitor has to be connected to the
product before you select this option.
Movie Frame (24 Fs)
Setting the Movie Frame (24Fs) feature to On
allows you to adjust the product's HDMI output to
24 frames per second for improved picture quality.
You can enjoy the Movie Frame (24Fs) feature only
on a TV supporting this frame rate. This menu can
only be selected in 1080i or 1080p HDMI output
resolution modes.
• Off : Movie Frame (24Fs) functions will not
work.
• On : Movie Frame (24Fs) functions will work.
✎ NOTE
 Two types of frame rates may be included,
depending on the disc: Movie material (24
frame) and Video material (30 frame). When the
setting switches between Movie (24 frame) and
Video (30 frame), the screen may blink for a
few seconds.
 If your TV does not support Movie Frame
(24Fs) function, the pop-up message will be
displayed.
• Auto : Select this to have the product
automatically set the best picture for the DVD
you're watching.
• Video : Select this for the best picture from
Concert or TV show DVDs.
Still Mode
Set the type of picture shown when you pause
DVD playback.
• Auto: Automatically set the best still picture
depending on the content.
• Frame : Select when pausing a scene with a
little action.
• Field : Select when pausing a scene with a lot
of action.
HDMI Deep Color
Set to output the picture from the HDMI OUT
jack with Deep Colour or not. Deep Colour allows
more accurate colour reproduction with deeper
colour depth.
• Auto: The picture will be output with Deep
Colour to the connected TV which supports
HDMI Deep Colour.
• Off : The picture will be output without Deep
Colour.
English
33
Setup
Distance
audio
If the speakers cannot be placed at equal
distances from the listening position, you can
adjust the delay time of the audio signals from the
front, centre, surround and subwoofer speakers.
Speaker Setting
Settings
Display
Audio
System
Network
Language
Security
General
Support
Speaker Setting
Level
|
Distance
Test tone
:
• You can set the Speaker Distance between
1ft(0.3m) and 30ft(9.0m).
Off
Settings
s Select
r Return
Level
Display
Audio
System
Network
Language
Security
General
Support
Distance
Front L
Front R
Center
Surround L
Surround R
Subwoofer
Test Tone
: ◄ 10ft (3.0m) |
:
10ft (3.0m)
:
10ft (3.0m)
:
10ft (3.0m)
:
10ft (3.0m)
:
10ft (3.0m)
:
Off
<Change s Select r Return
You can adjust the balance and level for each
speaker.
Adjusting Front/Centre/Surround/Subwoofer
Speaker Level
• The volume level can be adjusted in steps from
+6dB to -6dB.
• The sound gets louder as you move closer to
+6dB and quieter as you get closer to -6dB.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Level
Front L
Front R
Center
Surround L
Surround R
Subwoofer
Test Tone
:◄
:
:
:
:
:
:
0 dB
0 dB
0 dB
0 dB
0 dB
0 dB
Off
|
<Change s Select r Return
Test Tone
Use the Test Tone feature to check the speaker
connections.
Press the _, + buttons to select All.
• A test tone will be sent to Front Left ; Center
; Front Right ; Surround Right ;
Surround Left ; Subwoofer in order so you
can make sure the speakers are set up
correctly.
To stop the test tone, press the _, + buttons to
select Off.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Speaker Setting
Level
Distance
Test Tone
:◄
All
|
<Change s Select r Return
✎ NOTE
 When HDMI Audio is ON (audio is produced
through TV speakers), the Test Tone
function is not available.
English
03
By setting the Musical Auto Calibration (MAC)
function just once when you relocate or install the
product, you can have the product automatically
recognize the distance between speakers, levels
between channels, and frequency characteristics
to create a 5.1-channel sound field optimized for
your environment.
ASC IN
ASC
microphone
✎ NOTE
Setup
Musical Auto Calibration
 Setting the Musical Auto Calibration
function takes about 3 minutes.
 The Musical Auto Calibration setup can be made
when there is no disc in the product.
 If the ASC microphone is disconnected during the
Musical Auto Calibration setup, the setup will be
cancelled.
 When the Musical Auto Calibration function is
activated, the DSP, Dolby Pro Logic ll and SFE
Mode will not work.
 If the product is connected to external devices or
other components (such as an iPod, AUX, D.IN),
the Musical Auto Calibration Setup may not work
properly.
EQ Optimizer
Set optimal EQ automatically depending on the
region.
• Off : Turn EQ Optimizer off.
• On : Turn EQ Optimizer on.
Musical Auto Calibration
HDMI Audio
Musical Auto Calibration Setting
The audio signals transmitted over the HDMI
Cable can be toggled On/Off.
• Off : Video is transmitted over the HDMI
connection cable only, and audio is output
through your product speakers only.
• On : Both video and audio signals are
transmitted over the HDMI connection cable,
and audio is output through your TV speakers
only.
1. Plug the ASC microphone into the ASC IN jack.
✎ NOTE
You will hear either the Musical Auto Calibration
mode or the User Speaker Settings.
• Off: You will hear sound in the the Speaker
Setting value.
• On: You will hear sound in the Musical Auto
Calibration mode.
2. Place the ASC microphone at the listening position.
• Musical Auto Calibration will be automatically
set up in the following sequence:
Front Left ; Center ; Front Right ;
Surround Right ; Surround Left ;
Subwoofer
• Press the RETURN button to cancel the
Musical Auto Calibration Setting.
• When the message "REMOVE MIC" appears
in the display, unplug the ASC microphone.
 HDMI Audio is automatically down-mixed to
2ch for TV speakers.
English
35
Setup
✎ NOTE
Digital Output
Set Digital output depending on the connected
receiver. (For more details, please refer to the
digital output selection.)
• PCM
• Bistream(Re-encode)
• Bistream(Audiophile)
 Be sure to select the correct Digital Output
or you will hear no sound or a loud noise.
 If the HDMI device (Receiver, TV) is not compatible
with compressed formats (Dolby digital, DTS), the
audio signal outputs as PCM.
 Secondary and Effect audio will not be heard with
regular DVDs.
Blu-ray Discs may include three audio streams.
 Some Blu-ray Discs do not have Secondary and
- Primary Audio : The audio soundtrack of the
main feature.
 This Digital Output setup does not effect the
- Secondary Audio : Additional soundtrack
such as director or actor's commentary.
- Interactive Audio : Interactive sounds will be
heard when selected. Interactive Audio is
different on each Blu-ray Disc.
Effect audio.
analogue (L/R) audio or HDMI audio output to
your TV.
It effects the optical and HDMI audio output when
connected to a receiver.
 If you play MPEG audio soundtracks, audio signal
outputs PCM regardless of Digital Output
Selections (PCM or Bitstream).
Digital Output Selection
Setup
Connection
Definition for
Blu-ray Disc
36
Bitstream
(Audiophile)
HDMI Receiver
Optical
PCM
Up to 7.1ch
PCM 2ch
DTS re-encoded
PCM
PCM 2ch
Dolby Digital
Up to 5.1ch
PCM 2ch
DTS re-encoded
Dolby Digital
Dolby Digital
Dolby Digital
Plus
Up to 7.1ch
PCM 2ch
DTS re-encoded
Dolby Digital Plus
Dolby Digital
Audio Stream
on Blu-ray Disc Dolby TrueHD
Audio Stream
on DVD
Bitstream
(Re-encode)
PCM
HDMI Receiver or Optical HDMI Receiver
Optical
Up to 7.1ch
PCM 2ch
DTS re-encoded
Dolby TrueHD
Dolby Digital
DTS
Up to 6.1ch
PCM 2ch
DTS re-encoded
DTS
DTS
DTS-HD HRA
Up to 7.1ch
PCM 2ch
DTS re-encoded
DTS-HD HRA
DTS
DTS-HD MA
Up to 7.1ch
PCM 2ch
DTS re-encoded
DTS-HD MA
DTS
PCM
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
Dolby Digital
Up to 5.1ch
PCM 2ch
Dolby Digital
Dolby Digital
Dolby Digital
DTS
Up to 6.1ch
PCM 2ch
DTS
DTS
DTS
Any
English
Decodes Primary, Secondary and
Effect audio streams together into
PCM audio.
Outputs only the Primary audio
Decodes Primary, Secondary and
soundtrack (main soundtrack of the
Effect audio streams together into
movie) so that your receiver can decode
PCM audio, then re-encodes the
the audio bitstream. You will not hear
PCM audio into DTS bitstream.
Secondary and Effect audio.
03
Setup
Dynamic Range Control
Anynet+(HDMI-CEC)
You can listen at low volumes but still hear dialog
clearly. This is only active when a Dolby Digital
signal is detected.
• Off : You can enjoy the movie with the
standard Dynamic Range.
• On : When Movie soundtracks are played at
low volume or from smaller speakers, the
system can apply appropriate compression to
make low-level content more intelligible and
prevent dramatic passages from getting too
loud.
Anynet+ is a convenient function that offers linked
operations with other Samsung products with the
Anynet+ feature.
To operate this function, connect this product to
a Samsung TV with an HDMI cable.
You can operate this product using a Samsung
TV remote control and start disc playback simply
by pressing the PLAY (+) button on the TV’s
remote control.
For more information, please see the TV user
manual.
• Off : Anynet+ function will not work.
• On : Anynet+ functions will work.
AV Sync
Video may look slower than the audio when the
product is connected to a digital TV. If this
occurs, adjust the audio delay time to match the
video.
• You can set the audio delay time between
0 msec and 300 msec. Set it to the optimal
status.
System
Initial Settings
By using the Initial Settings, you can set
language, TV aspect, Musical Auto Calibration
and Network setting, etc.
For more information on the settings, refer to the
corresponding section in this user manual.
Internet@TV Screen Size
Set the Internet@TV Screen to the optimal size.
• Size 1 : Display smaller application icons, you
may see some black on sides of screen.
• Size 2 : Display normal application icons,
image may be too large for your TV screen.
• Size 3 : Display larger application icons, image
may be too large for your TV screen.
✎ NOTE
 This function is not available if the HDMI cable
does not support CEC.
 If your Samsung TV has an n logo, then
it supports the Anynet+ function.
 Depending on your TV, certain HDMI output
resolutions may not work.
Please refer to the user manual of your TV.
BD Data Management
Enables you to manage the downloaded
contents from the Blu-ray disc that supports the
BD-LIVE service.
You can check the device information including
the storage size, and delete the BD data or
change the device.
* You must have a minimum 1GB USB Memory
device inserted in one of the USB slots (The
Wireless LAN Jack also functions as a USB slot.)
in order to download content from BD-LIVE.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Menu :
BDOn-Screen
Data Management
Disc Menu: External Flash: Memory
Current Device
Total Size Audio
: 955MB
Delete BD Data
Change Device
|
: External Flash Memory
Subtitle : 949MB
Available Size
s Select
:
:
r Return
English
Setup
Description of Device(Storage) Information on
the Product
• Total Size : Total size of the Device (Storage).
• Available Size : Available size of the Device (Storage).
✎ NOTE
 In the external memory mode, disc playback




will be stopped if you disconnect the USB
device in the middle of the playback.
Only those USB devices formatted in FAT file
system (DOS 8.3 volume label) are supported,
and it is recommended to use USB devices
that support USB 2.0 protocol, 4 MB/sec or
faster read/write speed.
A USB HDD device cannot be used for BD
Data storage (BD-LIVE).
The Resume Play function may not work after
formatting the storage device.
The total size of BD Data Management may
differ, depending on the software version.
DivX(R) Registration
View DivX(R) VOD Registration Code to purchase
and play DivX(R) VOD content.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Initial Setting
Disc Menu
:
DivX(R)
AudioVideo On Demand:
Your registration
Subtitlecode is : XXXXXXXXXX
:
To learn more visit www.divx.com/vod
OK
✎ NOTE
 This option is not activated if you select OK.
To activate this option, please activate the
DivX(R) Deactivation.
Clock
DivX(R) Deactivation
Set time-related functions.
Select this to get a new registration code.
Settings
Display
On-Screen
ClockMenu :
Audio Clock Mode Disc Menu
:
: Auto
\
System Clock Set
Audio
:
Network Time Zone Subtitle : GMT + 0:00:
LanguageDST
: Off
Security
General
> Move s Select r Return
Support
• Clock Mode : You can select Auto or Manual.
If you select Manual, the Clock Set menu will
be activated while DST will be deactivated.
• Clock Set : You can specify the current time
and date manually.
• Time Zone : You can specify the time zone
that is applicable to your area.
• DST : You can set DST (Daylight Saving Time)
1 hour, 2 hour and off.
English
Settings
Display
Audio
System
Network
Language
Security
General
Support
Initial Setting
Disc Menu
:
Audio
:
Subtitle
:
Do you want
to deactivate your device?
Yes
No
✎ NOTE
 This function can be operated when DivX(R)
Registration function is deactivated.
03
To begin setting up the network connection for
your product, follow these steps:
1. In the Home menu, press the ◄► buttons to
select the Settings, and then press the
ENTER button.
2. Press the ▲▼ buttons to select Network,
and then press the ENTER button.
3. Press the ▲▼ buttons to select Network
Settings, and then press the ENTER button.
4. Press the ▲▼ buttons to select Network
Type, and then press the ENTER button.
5. Press the ▲▼ buttons to select Wired or
Wireless, and then press the ENTER button.
6. Go to the next section.
Network Settings
Please contact your ISP to find out if your IP
address is static or dynamic. If it is dynamic, we
recommend using the Auto setting. This is the
easiest and will work in the majority of cases. If it is
static, you must use the manual set up procedure.
Directions for wired networks are below. Directions
for wireless networks are after the directions for
wired networks.
Wired Network
1. In the Network Settings menu, press the
▲▼ buttons to select Network Settings,
and then press the ENTER button.
The Internet Protocol Setup screen appears.
2. Press the ► button, then select Auto or
Manual, and then press the ENTER button.
Setting up a Wired Connecton - auto
1. If you selected Auto, the Network Function
acquires and fills in the values for IP Address,
Subnet Mask, etc., automatically.
Setup
network Setup
Settings
Network Settings
Display
On-Screen Menu
Internet Protocol Setup : Auto
Audio
Disc Menu
0
IP Address
: 0
System
Audio
0
Subnet Mask
: 0
Network
Subtitle
0
Gateway
: 0
Language
DNS
: Auto
Security
0
DNS Server
: 0
General
Support
> Move
" Select
:
:
0
:
0
:
0
0
0
0
0
\
0
' Return
2. After the Network Function has acquired the
network values, press the RETURN button.
Then, run a Network Test to ensure the
product has connected to your network (See
page 42).
3. If the Network Function does not acquire the
network values or you selected Manual, go to
the directions for Manual Setup.
Setting up a Wired Connecton - manual
If the Auto Setting does not work, you’ll need to set
the Network Setting values manually.
To get the Network setting values from most
Windows computers, follow these steps:
1. Right click the Network icon on the bottom
right of the screen.
2. In the pop-up menu, click Status.
3. On the dialog that appears, click the Support
tab.
4. On the Support tab, click the Details button.
The Network settings are displayed.
To enter the Network settings into your product,
follow these steps:
1. On the Internet Protocol Setup screen, press
the ENTER button.
2. Press the ▲▼ buttons to select Manual,
and then press the ENTER button.
3. Press the ▼ button to go to the first entry
field (IP Address).
✎ NOTE
 This process can take up to five minutes.
English
Setup
Settings
Network Settings
Display
On-Screen Menu
Internet Protocol Setup : Manual
Audio
Disc Menu
0
IP Address
: 0
System
Audio
Subnet Mask
: 255 255
Network
Subtitle
0
Gateway
: 0
Language
DNS
: Manual
Security
0
DNS Server
: 0
General
Support
> Move
" Select
:
:
0
:
255
:
0
0
0
0
0
\
2.
Press the RED(A) button on the remote
control.
3.
Press the PBC (WPS) button on your router
within two minutes. Your product displays
the Network Selection Screen, and
automatically acquires all the network
setting values it needs and connects to your
network. When it is done, it displays an OK
button. Press the ENTER button on your
remote.
4.
After the network connection is set up,
press the RETURN button to exit the
Network Setting screen.
0
' Return
4.
Use the number buttons on your remote to
enter numbers.
5.
When done with each field, use the ►
button to move successively to the next
field.
You can also use the other arrow buttons to
move up, down, and back.
6.
Enter the IP Address, Subnet Mask, and
Gateway values.
7.
Press the ▼ button to go to DNS.
8.
Press the ▼ button to go to the first DNS
entry field. Enter the numbers as above.
9.
Press the RETURN button on your remote.
10. Run a Network Test to ensure the product
has connected to your network (See page
42).
Wireless Network
You can setup the wireless network three ways:
Setting up the Wireless network
Connection - auto network Search
Most wireless networks have an optional security
system that requires devices that access the
network to transmit an encrypted security code
called an Access or Security Key. The Security Key
is based on a Pass Phrase, typically a word or a
series of letters and numbers of a specified length
you were asked to enter when you set up security
for your wireless network. If you use this method
of setting up the network connection, and have
a Security Key for your wireless network, you will
have to enter the Pass Phrase during the setup
process.
 Setting Up the Network Connection
To set up the wireless connection using Auto
Network Search, follow these steps:
1.
In the Network Settings menu, press the
▲▼ buttons to select Network Settings,
and then press the ENTER button.
The Internet Protocol Setup screen appears.
Each method is described below.
2.
Setting up the Wireless network
Connection - PBC (WPS)
Press the ▲▼ buttons to select the
Internet Protocol Setup, and then press
the ENTER button.
3.
Press the ▲▼ buttons to select Auto or
Manual, and then press the ENTER button.
4.
If you selected Auto, press the ▲ button to
go to Access Point Selection, and then
press the ENTER button.
The Network function searches for available
wireless networks.
When done, it displays a list of the available
networks.
• Using PBC (WPS)
• Using the Auto Network Search function.
• Manually.
The easiest way to set up the wireless network
connection is using the PBC (WPS) function.
If your wireless router has a PBC (WPS) button,
follow these steps:
1.
In the Network Settings menu, press the
▲▼ buttons to select Network Settings,
and then press the ENTER button.
The Internet Protocol Setup screen appears.
0
English
03
Display
Audio
System
Network
Language
Security
General
Support
Network Settings
Network Selection
Connecting to network.
Network Name(SSID) : shj
Stop
" Select
' Return
5.
In the list of networks, press the ▲▼
buttons to select a network, and then press
the ENTER button.
6.
If the PIN/Security pop-up appears, go to
Step 7. If the Network Connecting Screen
appears, go to Step 11.
7.
8.
Press the ▲▼ buttons to select PIN or
Security.
For most home networks, you would select
Security (for Security Key).
On the Security screen, enter your network’s
Pass Phrase.
✎ NOTE
 You should be able to find the Pass Phrase
on one of the set up screens you used to set
up your router or modem.
9.
To enter the Pass Phrase, follow these
general directions:
• Press the number keys on your remote to
enter numbers.
• Use the arrow keys on your remote to
move from button to button on the
Security Key screen.
• To enter letters, move to the button
labelled a/A/1/, and then press the
ENTER button. Each time you press the
ENTER button, you change the kind of
characters you can enter (a/A/1/).
• To enter a letter, press the number button
that corresponds to the letter. Pressing
the button repeatedly changes the letter.
• To delete the last letter or number you
entered, move to the Delete button, and
then press the ENTER button.
• To clear all entered letters and numbers,
move to the Clear key, and then press the
ENTER button. You can also just press
the RED(A) button on your remote.
11. Wait until the connection confirmation
message is displayed, and then press the
ENTER button. The Network Settings
screen reappears.
12. To test the connection, press the ▼ button
to select Network Test, and then press the
ENTER button.
Setting up the Wireless network
Connection - manual
If the Auto Setting does not work, you need to
enter the Network settng values manually.
To get the Network setting values from most
Windows computers, follow these steps:
1.
Right click the Network icon on the bottom
right of the screen.
2.
In the pop-up menu, click Status.
3.
On the dialog that appears, click the
Support tab.
4.
On the Support tab, click the Details button.
The Network settings are displayed.
To Enter the Network settings into your product,
follow these steps:
1.
On the Internet Protocol Setup screen,
press the ENTER button.
2.
Press the ▲▼ buttons to select Manual,
and then press the ENTER button.
3.
Press the ▼ button to go to the first entry
field (IP Address).
4.
Use the number buttons to enter numbers.
Settings
Network Settings
Display
On-Screen Menu :
Access Point Selection : Not Selected
Audio
Disc Menu
:
Internet Protocol Setup : Manual
System
Audio
:
0
0
IP Address
: 0
Network
Subtitle
:
Subnet Mask
: 255 255 255
Language
0
0
Gateway
: 0
Security
DNS
: Manual
General
0
0
DNS Server
: 0
Support
a PBC (WPS) > Move
\
0
0
0
0
" Select ' Return
English
1
Setup
10. When done, press the YELLOW(C) button
on your remote, or move to the Done
button, and then press the ENTER button.
The Network Connecting screen appears.
Settings
Setup
5.
When done with each field, use the ►
button to move successively to the next
field.
You can also use the other arrow buttons to
move up, down, and back.
6.
Enter the IP Address, Subnet Mask, and
Gateway values.
7.
Press the ▼ to go to DNS.
8.
Press the ▼ button to go to the first DNS
entry field. Enter the numbers as above.
9.
When done, press the ▲ button to return to
Access Point Selection. Select the network,
and then press the ENTER button.
10. Go to Step 6 in the Automatic Wireless
procedure above, and follow the directions
from that point on.
Network Test
Use this menu to connect the wired network or
check whether your network connection is
working or not.
BD-LIVE Internet Connection
Set whether to allow internet connection when
BD-LIVE service is used.
• Allow (All) : The Internet connection will be
allowed for all BD-LIVE contents.
• Allow (Valid Only) : The Internet connection
will be allowed only for BD-LIVE contents
containing a valid certificate.
• Prohibit : No Internet connection will be
allowed for any BD-LIVE content.
✎ NOTE
 What is a valid certificate?
When the product uses BD-LIVE to send the
disc data and request to the server to certify
the disc, the server uses the transferred data
to check if the disc is valid and sends the
certificate back to the product.
 The Internet connection may be restricted
while you are using BD-LIVE contents.
Settings
Display
On-Screen
NetworkMenu
Test :
Audio
Disc Menu
:
 MAC Address (00:00:00:00:00:00)
System
Audio
:
 IP Address,Subnet Mask,Gateway,DNS Server
Network
Subtitle
:
Gateway Ping
Language Internet Service Test
Security
Network testing...
General
Support
Network Status
Check whether a connection to the network and
the Internet have been established.
English
Language
You can select the language you prefer for home
menu, disc menu, etc.
• On-Screen Menu : Select the language for the
on-screen displays.
• Disc Menu : Select the language for the disc
menu displays.
• Audio : Select the language for disc audio.
• Subtitle : Select the language for disc subtitles.
✎ NOTE
 The selected language will only appear if it is
supported on the disc.
03
Setup
Security
General
When you operate this menu for the first time,
password setup screen will be displayed. Enter
the desired 4-digit password using the number
buttons. (Default password is set to 0000.)
Background
Change the background theme of the menu
screen.
Parental Rating
This function works in conjunction with Blu-ray
Disc/DVDs that have been assigned a rating,
which helps you control the types of Blu-ray Disc/
DVDs that your family watches.
Select the rating level you want to set. A larger
number indicates that the program is intended for
adult use only. For example, if you select up to
Level 6, discs that contain Level 7, 8 will not play.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Background
Parental Rating
: Off
Change Password
Skin 1
Skin 2
Skin 3
Skin 4
Skin 5
> Move
s Select
r Return
Settings
Display
Audio
System
Network
Language
Security
General
Support
Parental Rating
Change Password
 Off
8(Adults)
7
6
5
4
▼
Change Password
Change the 4-digit password used to access
security functions.
Settings
Display
Audio
System
Network
Language
Security
General
Support
Change Password
Energy Saving
You can reduce power consumption by setting
the front panel to turn off automatically when
there is no operation for 5 seconds.
• Off : Energy Saving function is not used.
• On : The front panel will automatically turn off
when there is no operation for 5 seconds.
Front Display
Change the brightness of the front panel.
• Auto : Dim during playback only.
• Dim : Dim the display window.
• Bright : Brighten the display window.
Enter the password
Power On/Off Sound
Enter Pin r Return
If you forgot your password
Play a melody when the product is turned on and
off.
• Off : Turn Power Sound Off.
• On : Turn Power Sound On.
1. Remove the disc.
2. Press and hold the STOP (@) button on the
front panel for 5 seconds or more.
All settings will revert to the factory settings.
✎ NOTE
 When the factory default settings are restored, all the
user data stored in the BD data will be deleted.
English
Setup
Support
Software Upgrade
This menu allows you to upgrade software for
performance improvements or additional services.
You can check the current software version,
upgrade by internet and set the Auto upgrade
notification. If the product is properly connected to
the network by cable or wirelessly, the product will
automatically connect to our website each time it is
turned on and download update files if any valid
upgrade exists.
Settings
Display
Software Upgrade
Software
Audio
Disc MenuUpgrade :
System Current Version Audio : XXX-XXXXXXXXX
:
NetworkBy Internet
Subtitle
:
\
Language
Auto Upgrade Notification : On
Security
General
s Select r Return
Support
1. To select By Internet, press the ENTER
button.
A popup message will appear if an update is
available.
2. If you select Yes, the product will turn off
automatically before restarting.
(Never turn it on manually.)
3. The update progress popup will appear.
When the update is completed, the product
will turn back off automatically.
4. Press the POWER button to turn on the
product.
✎ NOTE
 The Update will be completed when the
product turns off after restarting. Press the
POWER button to turn on the updated product
for your use.
Never turn off or on the product manually during
the update process.
 Samsung Electronics shall take no legal
responsibility for product malfunction caused by
unstable of internet connection or consumer
negligence during software upgrade.
English
You can update software in any of the two ways
as follows: Software update is the same as in the
By Internet menu.
• USB : Visit www.samsung.com/bluraysupport,
then download and store the latest software
(RUF file) into the USB flash drive. Connect the
USB flash drive to the USB port of the product
(disc tray must be empty) to update the
software, then follow the on-screen
instructions.
• CD : Visit www.samsung.com/bluraysupport,
download and write the latest software (RUF
file) onto a disc. Insert and play the disc in the
product to start the update, then follow the onscreen instructions.
✎ NOTE
 Software upgrades using the USB Host jack
must be performed with no disc inside.
 If you want to cancel the upgrade in the
process of downloading the upgrade data,
press the ENTER button.
 When the system upgrade is done, check the
software details in the software Upgrade
menu.
 Do not turn off the product during the System
Upgrade, as it may cause the product to not
work properly.
 Do not use USB devices other than USB Flash
Drives to do software upgrades when using
the USB Host jack.
Contact Samsung
Provide contact information for assistance with
your product.
POWER
Disc Structure
DVD RECEIVER/TV
The contents of disc are usually divided as below.
Playback
• Blu-ray Disc, DVD-VIDEO
1. Press the OPEN/CLOSE ( ) button to open
the disc tray.
2. Place a disc gently into the tray with the
disc’s label facing up.
3. Press the PLAY (►) button or OPEN/
CLOSE ( ) button to close the disc tray.
Playback related buttons
PLAY ( +)
STOP ( @ )
chapter 1
title 2
chapter 2
1
SLEEP
2
3
4
5
6
track75
8
chapter 3
• Audio CD (CD-DA)
track 1
track 2
track 3
track 4
9
REPEAT
0
• MP3, WMA, DivX, MKV and MP4
folder (group) 1
file 1
file 2
file 1
folder (group) 2
file 2
file 3
Starts playback.
Stops playback.
• If pressing the button once:
The stop position will be
memorized.
• If pressing the button twice:
The stop position will be not
memorized.
(With some Blu-ray discs (BD-J),
this function may not work.)
PAUSE ( # )
title 1
chapter 1 chapter 2
FUNCTIO
TV SOURC
Basic Functions
Playing a Disc
04
Basic Functions
Pauses playback.
✎ NOTE
 "Not Available" will appear when an invalid
button is pressed.
Using the Disc menu / Title menu / Popup menu
Using the Disc Menu
MUTE
VOL
hZ
1. During playback, press the DISC
MENU button on the remote
control.
2. Press the ▲▼_ + buttons to make
the desired selection, then press the
ENTER button.
✎ NOTE
DISC MENU
SFE MODE
TUNING
/CH
MENU
TITLE MEN
POPUP
TOOLS
INFO
RETURN
EXIT
 Depending on the disc, the menu items may
differ and this menu may not be available.
A
INTERNET@
English
45
TUNER
MEMORY
B
C
MO/ST
D
DSP
0
Basic Functions
MUTE
POWER
FUNCTION
TV SOURCE
Using the Title Menu
DVD RECEIVER/TV
TUNING
/CH
SLEEP
SFE MODE
Z
1
DISC MENU
MENU
1. During playback, press
the TITLE
1
2
MENU button on the remote
control.
TOOLS
4 to 5
2. Press the ▲▼_ + buttons
POWER
make the desired selection, then
press the ENTER button.
7
8
DVD RECEIVER/TV
TITLE MENU
3
4
76
9
0
INFO
FUNCTION
TV SOURCE
REPEAT
SLEEP
EXIT
 Depending on the disc, the menu items may
TUNER
differ and this menu may not be available.
MEMORY
MO/ST
2 if there
3
 The Title Menu will onlyA1be displayed
B
C
D
are at least two titlesINTERNET
on the
@ disc.
4
DSP
5
Playing the Title List
6
MUTE
7
8
9VOL
0
z
REPEAT
VOL
TUNING
/CHMENU
DISC
SFE MODE
1. During playback, press the DISC
MENU or TITLE MENU button.
TITLE MENU
TOOLS
POPUP
INFO
RETURN
Using the Popup Menu
TUNING
/CH
SFE MODE
A
B
h
RETURN
EXIT
INTERNET@
MENU TUNER TITLE MENU
MEMORY
MO/ST
POPUP
1. During playback, press the POPUP
button on the remote Acontrol.B
C
DISC MENU
@
2. Press the ▲▼_ + INTERNET
buttons
or
TOOLS
ENTER button to select the
desired menu.
D
DSP
INFO
✎ NOTE
 Depending on the disc,
the menu items may
RETURN
EXIT
differ and this menu may not be available.
TUNER
MEMORY
INTERNET@
46
English
B
REPEAT
C
MO/ST
D
DSP
hzZyx
• During playback, press the SEARCH (())
button.
Each time you press the SEARCH (())
button, the playback speed will change as
follows.
MUTE
BD-ROM,
BD-RE/-R,
DVD-RW/-R,
TUNING
/CH
DVD+RW/+R,
SFE MODE
DVD-VIDEO
MENU
TITLE MENU
DivX, MKV, MP4
POPUP
DISC MENU
MENU
2. Press the ▲▼ buttons
to select
an entry you want to play from
Title List, then press the ENTER
TOOLS
button.
MUTE
VOL
During playback, you can search quickly through
a2chapter3or track, and use the skip function to
jump to the next selection.
5
6
Searching for a Desired Scene
8
9
POPUP
0
RETURN
A
SLEEP
Using
the Search and Skip Functions
DVD RECEIVER/TV
VOL
✎ NOTE
FUNCTION
TV SOURCE
POWER
)1)2)3
)4)5)6)7
(1(2(3
(4(5(6(7
)1)2)3
(1(2(3
INFO to normal speed playback, press the
• To return
PLAY (+) button.
✎ NOTE
 No sound
is heard during search mode.
EXIT
TUNER
MEMORY
MO/ST
Skipping
Chapters
C
D
DSP
hzZyx
• During playback, press the SKIP ([])
button.
If you press the SKIP (]) button, it moves to
the next chapter.
If you press the SKIP ([) button, it moves to
the beginning of the chapter. One more press
makes it move to the beginning of the previous
chapter.
04
Repeat
Basic Functions
Slow motion Play/Step motion Play
Off
Slow Motion Play
h�Z��
• In pause mode, press the SEARCH ())
button.
If you press the SEARCH ()) button, the
playback speed is reduced to
* 1/8 * 1/4 * 1/2
• To return to normal speed playback, press the
PLAY (+ ) button.
✎ NOTE
3. To return to normal play, press the REPEAT
button again.
✎ NOTE
DVD RECEIVER/TV
SLEEP
 Depending on the disc, the Repeat function
may not be available. 1
4
2
3
5
6
h�Z�
7
8
9
direction.
1. During playback, press the REPEAT
button on the remote control. 0
Step Motion Play
h�Z��
✎ NOTE
FUNCTION
TV SOURCE
 No sound is heard POWER
during step mode.
 Step motion operates only in the forward
DVD RECEIVER/TV
SLEEP
repeat Playback
1 Chapter
2
Repeat the Title or
5
6
h�Z�
Repeat the disc title or7chapter.8
1. During playback, press the REPEAT
button on the remote control. 0
Repeat
REPEAT A-B : Off
s Mark A
MUTE
TUNING
3. Press the ENTER button
VOL at the point where
/CH
you want repeat play to start SFE
(A).MODE
4. Press the ENTER button at the point where
DISCto
MENU
MENU
TITLE MENU
you want repeat play
stop (B).
POPUP
5. To return to normal play, press the REPEAT
button again.
TOOLS
3
INFO
6. Press the ENTER button.
✎ NOTE
 If you set point (B) before 5 seconds has
lapsed, the prohibition
message will appear.
RETURN
EXIT
9
REPEAT
REPEAT
2. Press the ▲▼ buttons to select
REPEAT A-B.
• In pause mode, press the PAUSE ( # ) button.
Each time the PAUSE ( # ) button is pressed, a
new frame will be appear.
• To return to normal speed playback, press the
PLAY ( + ) button.
4
FUNCTION
TV SOURCE
Repeat the Section
 No sound is heard during slow mode.
 Slow motion operates only in the forward
direction.
POWER
4. Press the ▲▼ buttons to select Off, the
press the ENTER button.
TUNER
MEMORY
A
B
C
INTERNET@
MO/ST
D
DSP
2. Press the ▲▼ buttons to select
Chapter or Title, then press the
ENTER button.
English
MUTE
TUNING
MUTE
Basic Functions
VOL
DISC MENU
MENU
using the tooLS button
During playback, you can operate disc
menu by pressing the TOOLS button.
TOOLS
• TOOLS Menu Screen
Tools
RETURN
Title
:
1/1
Chapter
4/21
Playing Time
:
00:12:06
Repeat
A
Audio
: 1/7 ENG Multi CH
INTERNET@
Subtitle
:
1/6 ENG
Angle
:
1/1
BONUSVIEW Video :
Off
BONUSVIEW Audio :
0/1 Off
TUNING
/CH
SFE MODE
B
TITLE MENU
 Information
about the primary / secondary
POPUP
mode will be also displayed if the Blu-ray Disc
INFOa BONUSVIEW section.
has
Use the ◄► button to switch between
primary and secondary audio modes.
 This function depends on what audio
languages are encoded on the disc and may
EXIT
not be available.
TUNER
 A Blu-ray
Disc can contain up to 32 audio
MEMORY
MO/ST
and a DVD up to 8.
C languages
D
 Some
Blu-ray Discs may allow you to select
DSP
either the multi-channel LPCM or Dolby digital
audio soundtrack in English.
Picture Setting
< Change " Select
✎ NOTE
▪ Depending on the disc, the TOOLS menu
may differ.
Moving to a Desired Scene Directly
Selecting the Subtitle Language
hZ�
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Subtitle.
3. Press the ◄► buttons to select the desired
subtitle language.
h�Z� ✎ NOTE
1. During playback, press the TOOLS button.
 Depending on the Blu-ray Disc / DVD, you may
2. Press the ▲▼ buttons to select Title,
Chapter or Playing Time.
3. Enter the desired Title, Chapter or Playing
Time using the number buttons, then press
the ENTER button.
Selecting the Audio Language
h�Z�
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Audio.
3. Press the ◄► buttons to select the desired
audio language.
✎ NOTE
 The ◄► indicator will not be displayed on the
screen if the BONUSVIEW section does not
contain any BONUSVIEW audio settings.
English





be able to change the desired subtitle in the
Disc Menu.
Press the DISC MENU button.
This function depends on what subtitles are
encoded on the disc and may not be available
on all Blu-ray Discs/DVDs.
A Blu-ray Disc can contain up to 255 subtitle
languages and a DVD up to 32.
Information about the primary / secondary
mode will also be displayed if the Blu-ray Disc
has a BONUSVIEW section.
This function changes both the primary and
secondary subtitles at the same time.
The total number of subtitles is the sum of the
primary and secondary ones.
04
�
• You must have some experience with video
extraction and editing in order to use this
feature properly.
• To use the caption function, save the caption
file (*.smi) in the same file name as that of the
DivX media f le (*.avi) within the same folder.
Example. Root Samsung_007CD1.avi
Samsung_007CD1.smi
• Up to 60 alphanumeric characters or 30 East Asian
characters (2 byte characters such as Korean and
Chinese) for the file name.
• User : The user can adjust the sharpness
and noise reduction function respectively.
Setting the BONUSVIEW
h
The BONUSVIEW feature allows you to view
additional content (such as commentaries) in a
small screen window while the movie is playing.
This function is only available if the disc has the
bonusview feature.
Changing the Camera Angle
hZ
When a Blu-ray Disc/DVD contains multiple
angles of a particular scene, you can use the
ANGLE function.
1. During playback, press the TOOLS button.
Primary a audio/video
Secondary a audio/video
2. Press the ▲▼ buttons to select Angle.
3. Press the ◄► buttons to select the desired
Angle.
1. During playback, press the TOOLS button.
Selecting the Picture Setting
3. Press the ◄► buttons to select the desired
bonusview.
2. Press the ▲▼ buttons to select BONUSVIEW
Video or BONUSVIEW Audio.
h�Z� ✎ NOTE
This function enables you to adjust video quality
when you are connected to a TV via HDMI.
1. During playback, press the TOOLS button.
2. Press the ▲▼ buttons to select Picture
Setting, then press the ENTER button.
3. Press the ◄► buttons to select the desired
Picture Setting, then press the ENTER
button.
• Dynamic : Choose this setting to increase
Sharpness.
• Normal : Choose this setting for most
viewing applications.
• Movie : This is the best setting for watching
movies.
 If you switch from BONUSVIEW Video,
BONUSVIEW Audio will change automatically
in accordance with BONUSVIEW Video.
Tools
BONUSVIEW Video
Off
BONUSVIEW Audio :
0/1 Off
Picture Setting
< Change " Select
English
Basic Functions
Caption Function
Basic Functions
FUNCTION
TV SOURCE
POWER
Listening to music
SLEEP
BD RECEIVER/TV
1
2
BD RECEIVER/TV
8
3
o�
FUNCTION
TV SOURCE
Buttons onPOWER
the Remote Control
4
5
6
used for Music Playback
7
FULL SCREEN
!
1
0
2
4
5
SLEEP
9
8
STOP button : Stops a track.
9
SKIP(]) button : During playback, moves to
the next page in the Music List or moves to the
next track in the Playlist.
0
SKIP ([)button : During playback, moves to the
previous page in the Music List or moves to the
previous track in the Playlist.
If you press this button after three seconds of
playback in the Playlist, the current track will be
replayed from the beginning. But, if you press this
button within three seconds after playback starts
in the Playlist, the previous track will be played.
!
NUMBER button : During the Playlist playback,
press the desired track number. The selected
track will be played.
3
6
7
8
9
MUTE
REPEAT
0
VOL
ENTER button : Plays and pauses the selected
track.
REPEAT
FULL SCREEN
0
7
TUNING
/CH
SFE MODE
1
2
9
DISC MENU
8
MENU
TITLE MENU
MUTE
POPUP
TOOLS
3
4
INFO
VOL
TUNING
/CH
SFE MODE
5
7
DISC MENU
RETURN
TOOLS
A
MENU
TITLE MENU
EXIT
POPUP
TUNER
MEMORY
B
C
MO/ST
INFO
D
INTERNET@
DSP
RETURN
EXIT
6
1
REPEAT buttons : Selects
the play mode in the
TUNER
MO/ST
MEMORY
Playlist.
A
B
C
D
2
@
SEARCH INTERNET
buttons
: Fast Play.
(Audio CD (CD-DA) only)
3
PAUSE button : Pauses playback.
4
PLAY button : Plays the currently selected track.
5
▲▼ buttons : Selects a track in the Music List
or Playlist.
6
YELLOW(C) button : Select or deselect a track
in the music list.
0
English
DSP
DVD RECEIVER/TV
SLEEP
2
3
4
5
6
Repeat an Audio CD
7 (CD-DA)/MP3
8
9
1. Insert an Audio CD (CD-DA) or an MP3 Disc
into the disc tray.
• For an Audio CD (CD-DA), the first track will
be played automatically.
• For an MP3 disc, press the ◄► buttons to
select Music, then press the ENTER
button.
1. During the Playlist playback, press
0
the REPEAT button.
Audio CD (CD-DA)/MP3 Screen Elements
1
2
05:57
04:07
TRACK 004
00:08 / 05:57
03:17
TRACK 006
5
) Track
Audio CD
(CD-DA)
03:35
Tools
r Return
4
1
Displays the music information.
2
Displays the playlist.
3
Shows the current track/total tracks.
4
Displays buttons available.
5
Shows the current play time/total play time.
6
Displays the current playback status.
7
Displays the repeated playback status.
Current track is repeated.
TUNING
VOL
/CH
CurrentSFE
track
MODEis repeated.
(
) One
MP3
(
) All
Audio CD
All tracks are repeated.
(CD-DA)/MP3
DISC MENU
MENU
TITLE MENU
(
) Shuffle
POPUPa
Audio CD
The random option plays
(CD-DA)/MP3 disc's track in random order.
03:41
TRACK 005
s Pause
Tracks on a disc are played
Audio CD
in the order in which they
(CD-DA)/MP3
were recorded
MUTE on the disc.
04:27
TRACK 003
+
(
Off
1/12
TRACK 001
TRACK 002
7
6
2. Select the desired play mode by
pressing the REPEAT button repeatedly.
3
Playlist
TRACK 001
REPEAT
TOOLS
INFO
Playlist
1. Insert an Audio CD (CD-DA) or an MP3 Disc
into the disc tray. RETURN
EXIT
• For an Audio CD (CD-DA), the first track will
TUNER
MEMORY
MO/ST
be played automatically.
A
B
• For an MP3 disc, press
the
◄► CbuttonsD to
INTERNET@
select Music, then press the ENTER DSP
button.
2. To move to the Music List, press the STOP (@)
or RETURN button.
The Music List screen is displayed.
3. Press the ▲▼◄► buttons to move to the
desired track, then press the YELLOW(C) button
to check desired tracks.
Repeat this procedure to select additional tracks.
Music
TRACK 001
TRACK 002
TRACK 003
TRACK 004
TRACK 005
TRACK 006
TRACK 007
TRACK 008
TRACK 009
TRACK 010
00:05:57
2. Press the ▲▼ buttons to select the track
you want to play, and then press the ENTER
button.
00:04:07
00:03:17
00:03:47
00:03:53
CDDA
3 files selected 1/2 Page
TRACK 003
00:04:27
00:03:41
00:03:35
00:03:49
00:03:45
c Select
() Jump page
r Return
English
1
Basic Functions
Playing an Audio CD (CD-DA)/MP3
04
1
VOL
SFE MODE
DISC MENU
Basic Functions
TOOLS
5. Press the ENTER button to play the selected
tracks.
The selected track will automatically play.
1/1
Playlist
+
TRACK 001
05:57
TRACK 002
04:27
TRACK 003
04:07
00:08 / 05:57
s Pause
MENU
Tools
r Return
INFO
Sound mode
DSP(Digital Signal Processor) Function
RETURN
EXIT
This will regulate and stabilize the volume
level
TUNER
POWER
MEMORY
MO/ST
against a drastic volume change when
changing
A transition.
B
C
D
channels or during a scene
INTERNET@
Press the DSP button.
7. To go to the Playlist, press the ENTER
button.
✎ NOTE
 You can create a playlist with up to 99 tracks
FUNCTION
TV SOURCE
DSP
DVD RECEIVER/TV
SMART SOUND  MP3 ENHANCER 
POWER BASS  DSP MODE OFF 1
SLEEP
2
3
• SMART SOUND : This will regulate and
stabilize the volume level against a drastic
4
5
volume change when changing channels or
during a scene transition.
6
7
6. To go to the Music List, press the STOP (@)
or RETURN button.
on Audio CD (CD-DA).
TITLE MENU
POPUP
4. If there is an undesired track in the playlist,
press the YELLOW(C) button again.
The selected track will be deleted.
TRACK 001
TUNING
/CH
8
• MP3 ENHANCER : This also helps enhance
your sound experience (ex. mp3 music). You
can upscale your MP3 level sound(24 kHz,0
8bit) to CD level sound(44.1 kHz, 16bit).
9
REPEAT
• POWER BASS : This function stresses low
tones providing thudding sound effects.
SFE(Sound Field Effect) MODE
MUTE
You can set the SFE mode best suited for the
type of music you are listening to. VOL
SFE MODE
TUNING
/CH
Press the SFE MODE button.
DISC MENU
MENU
TITLE MENU
POPUP
HALL1
Provides a clear vocal
TOOLSas if
listening in a concert hall.
HALL2
Provides also a clear vocal as if
listening in a concert hall but, less
powerful than HALL1.
JAZZ
Recommended setting for Jazz.
INFO
RETURN
CHURCH
ROCK
SFE OFF
English
EXIT
TUNER
MEMORY
Gives the feel of being
A in a Bgrand C
church.
INTERNET@
Recommended setting for Rock.
Select this for normal listening.
MO/ST
D
DSP
TOOLS
INFO
MUTE
VOL
EXIT
TUNER
MEMORY
B
C
INTERNET@
DSP
You can select the desired Dolby Pro
Logic II audio mode.
Press the
MUSIC
During the slide show playback, you
can use various function by pressing
the TOOLS button.
PL II button.
When listening to music, you can experience
sound effects as if you are listening to the
actual performance.
Slide Show Speed :
PROLOG
You will experience a realistic multi-channel
effect, as if using six speakers, while using
just the front left and right speakers.
MATRIX
You will hear multi channel surround sound.
STEREO
Select this to listen to sound from the front left
and right speakers and the subwoofer only.
connect your external device to the AUDIO
INPUT jacks (L and R) on the product. If you
connect to only one of the inputs (L or R), you
cannot listen to surround sound.
 This mode is available only with 2 channel audio.
Playing back a Picture
G
Playing a JPEG Disc
1. Insert a JPEG disc into the disc tray.
2. Press the ◄► buttons to select the Photos,
and then press the ENTER button.
3. Press the ▲▼◄► buttons to select the
folder you want to play, and then press the
ENTER button.
> Move
POPUP
INFO
EXIT
TUNER
MEMORY
Normal
Background Music
Information
TITLE MENU
RETURN
A
Rotate
 When selecting Dolby Pro Logic II mode,
TOOLS
Tools
Adds realism to the movie soundtrack.
✎ NOTE
MENU
Stop Slide Show
Zoom
MOVIE
DISC MENU
MO/ST
Using
the TOOLS button
D
Basic Functions
Dolby Pro Logic II ModeA
04
RETURN
TUNING
/CH
SFE MODE
B
INTERNET@
" Enter
' Return
• Start Slide Show : Select this if you want to
start the slide show.
• Slide Show Speed : Select this if you want to
adjust the Slide Show speed.
• Background Music : Select this if you want to
listen to music while viewing a picture.
• Zoom : Select this if you want to enlarge the
current picture. (Enlarged up to 4 times)
• Rotate : Select this if you to rotate the picture.
(This will rotate the picture either clockwise or
counter clockwise.)
• Information : Shows the picture information
including the name and size, etc.
✎ NOTE
 To enable the Background Music function,
both music and MP3 files must be contained in
the same folder. However, the sound quality
can be affected by the bit rate of the MP3 file,
the size of the photo and the encoding
method.
4. Press the ▲▼◄► buttons to select the
photo you want to play, and then press the
ENTER button.
✎ NOTE
 You can't enlarge the subtitle and PG graphic
in the full screen mode.
English
C
MO/ST
D
DSP
Basic Functions
✎ NOTE
Playing back a uSB Storage
F
You can use the USB connection to play multimedia
files (MP3, JPEG, DivX, etc) downloaded from the
USB storage device.
1. Move to the home menu.
2. In Stop mode, connect the USB storage device
to the USB port on the front panel of the product.
The message “Do you want to access the
device?” will be displayed.
3. Press the ◄► button to select Yes, then
press the ENTER button.
4. Press the RED(A) button.
 You must remove the USB storage device
safely (by performing the “Safe to Remove
Hardware” function) in order to prevent a
possible damage to the USB memory. Press
the MENU button to move to the main screen,
and select the YELLOW(C) button and press the
ENTER button.
 When the Audio-CD (CD-DA), MP3 and JPEG
files are in stop mode, you can't see full screen
by pressing the FULL SCREEN button on the
remote control.
 If you insert the disc when playing USB storage
device, the device mode is changed to “DVD
or CD” automatically.
 To listen to your music files with 5.1 channel sound,
you must set the Dolby Pro Logic II mode to Matrix.
(See page 53)
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
Listening to radio
Using buttons on the Remote Control
CD
USB
USB a Change Device c Safely Remove USB d View Devices " Enter
5.
Press the ▲▼ buttons to select the USB,
then press the ENTER button.
6. Press the ◄► buttons to select the desired Videos,
Music or Photos, then press the ENTER button.
4-1. Press the BLUE(D) button.
Please activate Internet@TV service
to enjoy a variety of Internet Services.
USB
1. Press the FUNCTION button to select FM.
2. Tune in to the desired station.
• Automatic Tuning 1 : When the [ ] button
is pressed, a preset broadcast station is selected.
• Automatic Tuning 2 : Press and hold the
TUNING/CH(
) button to automatically
search for active broadcasting stations.
• Manual Tuning : Press the TUNING/CH
(
) button to increase or decrease the
frequency incrementally.
Using buttons on the product
1. Press the FUNCTION (
USB
d Home
" Enter
5-1. Press the ◄► buttons to select the USB,
then press the ENTER button.
6-1. Press the ▲▼ buttons to select the desired
Videos, Music or Photos, then press the
ENTER button.
7. For playing back Video, Music or Photos
files, see pages 45~53.
English
) button to select FM.
2. Select a broadcast station.
• Automatic Tuning 1 : Press the STOP (  )
button to select PRESET and then press the
[ ] button to select the preset station.
• Automatic Tuning 2 : Press the STOP (  )
button to select MANUAL and then press and
hold the [ ] button to automatically
search the band.
• Manual Tuning : Press the STOP (  ) button to
select MANUAL and then press the [ ]
button to tune in to a lower or higher frequency.
DISC MENU
7
MENU
TITLE MENU
8POPUP
9
REPEAT
0 INFO
TOOLS
04
EXIT
using an iPod
TUNER MUTE
MEMORY
MO/ST
Press the MO/ST button.A
B
C
D
@
INTERNET
DSP
• Each time the button is
pressed,
the
VOL
sound switches between STEREO SFE MODE
and MONO.
• In a poor reception area, select
MONOMENU
for a
DISC MENU
clear, interference-free broadcast.
Basic Functions
RETURN
Setting Mono/Stereo
TUNING
/CH
You can enjoy music, video files from an iPod
through the product.
FM ANT
LAN
WIRELESS
DIDITAL
AUDIO IN
OPTICAL
TITLE MENU
SPEAKER IMPEDANCE : 3
WIRELESS LAN
POPUP
iPod
Presetting Stations
TOOLS
COMPONENT OUT
HDMI OUT
HDMI
OUT
iPod
INFO
Example : Presetting FM 89.10 into memory
1. Press the FUNCTION button to select FM.
2. Press the TUNING/CH( RETURN
) button to select EXIT
<89.10>.
TUNER
MEMORY
MO/ST
3. Press the TUNER MEMORY button.
A
B
C
D
Listening to Music
• NUMBER flashes on theINTERNET
display.
@
DSP
4. Press the [ ] button to select
You can play music files stored in the iPod player by
preset number.
connecting it to the product.
• You can select between 1 and 15 presets.
5. Press the TUNER MEMORY button again.
Please activate Internet@TV service
YouTube
Tube
You
• Press the TUNER MEMORY button before
to enjoy a variety of Internet Services.
NUMBER disappears from the display.
• NUMBER disappears from the display and
the station is stored in memory.
6. To preset another station, repeat steps 2 to 5.
No disc
• To tune in to a preset station, press the [ ]
iPod
iPod
button on the remote control to select a channel.
No Disc a Change Device
d View Devices s Enter
internet radio
MEMU
1. Connect the iPod dock connector to the iPod
Jack on the rear panel of the product.
2. Place the iPod in the supplied iPod Dock.
• Your iPod is automatically turned on.
• “iPod” message appears on the TV screen.
3. Press the RED(A) button.
4. Press the ▲▼ buttons to select iPod, then press
the ENTER button.
5. Press the ◄► buttons to select Music, then
press the ENTER button.
6. Select the music file to play.
- You can use the remote control or product to
control simple playback functions such as the
PLAY, PAUSE, STOP, [/ ], (/ ) and
REPEAT buttons. See page 15.
English
AUX IN
VIDEO OUT
Basic Functions
✎ NOTE
 Adjust the volume to a moderate level before
you connect your iPod and product.
 When the product is powered on and you
connect an iPod, the product will charge your
iPod's battery.
 Make sure to connect the dock connector so
that the label “SAMSUNG” faces upward.
 “Made for iPod” means that an electronic accessory
has been designed to connect specifically to the
iPod and has been certified by the developer to meet
Apple performance standards.
 “Works with iPhone” means that an electronic
accessory has been designed to connect specifically
to an iPhone and has been certified by the developer
to meet Apple performance standards.
iPod Music categories
File information including the artist name, album
name, music title and genre will be displayed
according to the ID3 Tag information on the
appropriate music file.
Now
Playing
Plays a recently played file or
moves to the playback screen of
the current file.
Artist
To play by artist.
Songs
To play in numeric or alphabetical
order
Playlist
To play by Playlist.
Album
To play by album.
Generic
To play by genre.
Composers
To play by composer.
✎ NOTE
 The category list may differ, depending on the
iPod model.
 What is an ID3 Tag?
This is what is attached to an MP3 to carry
information relevant to the file such as the title,
artist, album, year, genre and a comment field.
56
English
Watching a Movie
You can play video files stored in the iPod player
by connecting it to the product.
1. Connect the iPod dock connector to the
iPod Jack on the rear panel of the product.
2. In the iPod screen, move to Settings >
Videos, then set the TV Out option and the
TV signal.
3. Place the iPod in the supplied iPod Dock.
• “iPod” message appears on the TV
screen.
4. Press the RED(A) button.
5. Press the ▲▼ buttons to select iPod, then press
the ENTER button.
6. Press the ◄► buttons to select Videos, then
press the ENTER button.
7. Select the video file to play.
- You can use the remote control or the
product to control simple playback functions
such as the PLAY, PAUSE, STOP, [ /]
and( /)buttons. (See page 15.)
iPod models that can be used with
this product
iPod nano
3rd generation
(video)
iPod
5th generation
(video)
iPod nano
4th generation
(video)
iPod touch
1st generation
iPod touch
2nd generation
iPhone 3G
iPod classic
iPhone
✎ NOTE
 You must have the VIDEO output (Composite)
connected to your TV to view iPod video (See page 25).
 If you want to iPod video via VIDEO output, set
Anynet+(HDMI-CEC) to off.
 No other screen than the playback one will appear on
the TV screen. Check other screens on the iPod player.
 If the connected iPod does not support video playback,
the “Cannot play video files saved on this iPod”
message appears when you select the Video menu.
 Apple is not responsible for the operation of this device
or its compliance with safety and regulatory standards.
4
5
7
8
Network Services
9
REPEAT
05
0
Check the following instructions before using
any network service.
Internet@TV
at a Glance
TUNING
1. Connect the product to the network.
VOL
(see pages 27~28)
/CH
SFE MODE
1
DISC MENU
MENU
2
TITLE MENU
Recommended
POPUP
using Internet@tv
TOOLS
A
You can also initiate this function
by pressing the INTERNET@ button
on the remote control.
Contents 1
B
Contents 2
Contents 3
My Applications
INFO
Connect this product to the network to download
various for a fee or free-of-charge applications.
Internet@TV brings useful and entertaining
content and services directly from the webRETURN
to
your product such as news, weather forecasts,
stock market quotes, games, movies and music.
3
Contents 1
Contents 2
Contents 4
by Date 1/3
Contents 3
Samsung AppS Settings
a Login
EXIT
TUNER
MEMORY
6
MO/ST
C
D
INTERNET@
5
b Mark as Favorite
d Sort by ' Return
4
DSP
1
Commercial : Displays Internet@TV Guide,
product introduction and new application
introduction.
Getting Started with Internet@TV
2
Recommended : Displays recommended
contents managed by Samsung.
1. Move to the home menu.
3
My Application : Displays your personal gallery
which can be added and deleted by you.
4
Navigation Help : Displays remote control
buttons available.
• RED(A) : To log in to to Internet@TV.
• BLUE(B) : To mark the application as a
favorite.
• GREEN(D) : To sort the applications.
• Return : To return to the previous
menu.
5
Settings : You can set the system setup and
create accounts, etc.
6
Samsung AppS : You can download various
chargeable or free-of-charge application services.
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
No Disc
a Change Device
d View Devices
" Enter
2. Press the ◄► buttons to select Internet@
TV and press the ENTER button.
3. In the start screen of the Internet@TV service,
you will see the service agreement screen.
You must agree to the service terms and
conditions before you can use the Internet@
TV service.
English
Network Services
4. After you have signed off on the service
agreement, the Internet@TV service starts
updating. It takes several minutes. When the
update is complete, you will see the
MUTE
Internet@TV menu screen.
You can enjoy various network services such as
Internet@TV or BD-LIVE by connecting the
product to the network system.
2. Configure the network settings.
(see pages 39~42)
6
Network Services
Using the Keypad
13. Press the ENTER button.
Through your remote, you can use the
On-Screen Keypad in several Internet@TV
applications to enter text.
Pressing the FULL SCREEN button on the
remote while you are using the Screen Keypad
lets you to change the text fields to lower case,
upper case, numbers and icons.
14. The map and address appear on the screen.
✎ NOTE
 Samsung Electronics shall take no legal
responsibility for any interruption of the
Internet@TV service caused by the service
provider for any reasons.
 The Internet@TV service is to download and
1
2
abc
3
def
4
ghi
5
jkl
6
mno
7
pqrs
8
tuv
9
wxyz
a
Delete
]
0
Input Mode
A
1

For example, here is how to search an address in
Google Maps:
process data via the Internet so that you can
enjoy the contents on the TV screen.
If the Internet connection is unstable, the
service may be delayed or interrupted.
Furthermore, the product may be turned off
automatically.
If this is the case, check the Internet
connection and try again.
 The application service may be provided in
English only and the contents available may
vary, depending on the area.
1.
Press the ENTER button on the remote at
the Google Maps icon at the Internet@TV.
2.
Press the GREEN(B) button to use the
SEARCH function.
service, visit the web site of the applicable
service provider.
3.
Press the ◄► buttons to move to the
"Search or address" window.
 The services provided are subject to change,
4.
Press the ENTER button to use Search or
address function.
 The Internet@TV service contents may differ
5.
For example, suppose that you want to input
“105 Challenger Rd., Ridgefield Park NJ’.
 For-a-fee DivX contents with copy protection
6.
Press the FULL SCREEN button on the
remote twice to change the input mode from
lower case to numbers.
7.
Press ‘1’, ‘0’, ‘5’.
8.
Press the YELLOW(C) button on the remote
to input a blank space.
9.
Press the FULL SCREEN button on the
remote 3 times to change the input mode
from numbers to upper case.
10. Press ‘2’ button on the remote 3 times to
input C.
11. Press the FULL SCREEN button on the
remote 3 times to change the input mode
from upper case to lower case.
12. Press buttons on the remote to input the rest
of ‘Challenger Rd., Ridgefield Park NJ’.
58
English
 For more information about the Internet@TV
depending on the Internet@TV service
provider.
according to the firmware version.
can only be played using HDMI cable.
If you have connected your player to your TV
using Component or video cables, the DivX
video signal can not output or the popup
message “Connect with a HDMI cable to play
this file.”or “Cannot play current file” will be
displayed.
05
System Setup
For a more enjoyable application experience,
register and log in to your account.
Reset
To do this, you must create an account first. (For
instructions on creating an account, refer to
Internet@TV ID on this page)
1.
Press the ▲▼◄► buttons to select the
desired application and press the RED(A)
button.
Login
User Account :
Resets Internet@TV settings to factory default
settings.
✎ NOTE
 If you forgot your password, press the STOP
(@) button on the front panel of the product for
more than 5 seconds with no disc inserted.
Internet@TV ID
Use this menu to create or delete an account and
enter or delete account information.
adgim
You can control your account including contents
site’s account information.
Password :
a Create
[0~9] Enter PIN ' Cancel
This account is only for Internet@TV.
Create
2.
Enter the user account and password.
Settings
✎ NOTE
Create IDs and configure Internet@TV settings
from this screen.
 The account name must be at least 1
character in length but no more than 8.
 You can register up to 10 User Account
Settings
 System setup
 Internet@TV ID
 Service Manager
 Properties
Create an account and link it with desired service
applications.
Names.
Change the Service Lock password
Reset
' Cancel
Manager
• Service Site : Register login information for
service sites.
• Change Password : Change account
password.
• Delete : Delete the account.
English
Network Services
Account Login
Network Services
Service Manager
Delete and lock applications installed to Internet@
TV.
Lock
Lock the application. Accessing a locked
application requires the password.
Using the colour buttons with the Samsung
Apps
• RED(A) (Login) : To log in to the internet
service.
• GREEN(B) (Thumbnail View) : To change the
view mode.
• BLUE(D) (Sort By) : To sort the applications
by Featured, Most Downloaded, Most Recent
or Name.
Delete
Delete the application.
Internet@TV Services Available
Properties
- YouTube : You can view video streamed by
YouTube.
Display information about Internet@TV. Use the
Check the speed of your internet connection
option to test your network connection.
✎ NOTE
 The available Internet contents services may
be added or deleted.
Samsung AppS
Various applications are available from here,
organized into different categories. Some
applications have a download fee.
Samsung AppS
What's New!
 Video
 Sports
 Lifestyle
 Games
 Infomation
 Other

Video
Featured
1/1
Most downloaded
Most recent
YouTube
TV store Test User002
Name
Free
My Applications
Help
a Login
b Thumbnail View
d Sort By
' Return
My Application
Displays the application list.
Help
If you questions about Internet@TV, check this
section first. If none of the tips apply, please visit
the help website.
0
English
05
Once the product is connected to the network,
you can enjoy various movie-related service
contents using a BD-LIVE compliant disc.
1. Check the size of the remaining memory.
The memory device must have at least 1GB
of free space to accommodate the BD-LIVE
services.
2. Insert a Blu-ray disc that supports BD-LIVE.
3. Select an item from various BD-LIVE service
contents provided by the disc manufacturer.
✎ NOTE
 The way you use BD-LIVE and the provided
contents may differ, depending on the disc
manufacturer.
Software upgrade notification
In network connection, the product will notice you of
any new software version with a popup message.
1. Turn on the product.
2. From the Software Upgrade menu, set Auto
Upgrade Notification to On. (See page 44)
If there is a new software version available,
the product will notice you with a popup
message.
3. To upgrade the firmware, select Yes.
It will turn off automatically before restarting.
(Never turn it on manually.)
4. The update progress popup will appear.
When the update is completed, it will turn
back off automatically.
using the allShare function
AllShare enables you to play music, video and
photo files in your PC using the product.
To use AllShare, you must connect the product to
your PC via the network (See pages 27~28) and
install the SAMSUNG PC Share Manager on the PC.
1. Visit the Samsung website at www.samsung.
com.
2. Download the SAMSUNG PC Share
Manager and install it on the PC.
3. When the installation is completed, you will
see the SAMSUNG PC Share Manager icon
on your desktop. Double-click the icon to
launch the application.
4. Select a folder to share from the My
computer pane, and click the Share Folder
Enabled icon ( ).
(To remove a shared folder : Select a folder
to remove from the shared folders, and click
the Share Folder Disabled icon ( ).)
5. To apply the updated sharing state to the
server, click the Set Change State icon (
).
6. To enable the product to locate a PC server,
click Share from the menu bar.
Click Set Device Policy and click Accept.
SAMSUNG PC Share Manager
File
Share
Server
Help
Server : PC Share Manager
Set Device Policy
My Computer
Shared Folder
C: Document and settings Admin
IP
Device
Name
Size
Kind
SAMSUNG Blu-ray
FolderXXX.XXX.X.XX
1
FileDisc Player
Folder 2
Folder 3
Folder
State
Folder 1
Deny
Delete Selected Item
Full Path
Set State
C: Document and settin..
Accept
File
File
OK
Cancel
5. Press the POWER button to turn on the
product.
✎ NOTE
 Update will be completed when the product
turns off after restarting. Press the POWER
button to turn on the updated product for your
use.
Never turn off or on the product manually
during the update process.
 Samsung Electronics shall take no legal
responsibility for product malfunction caused by
unstable of internet connection or consumer
negligence during software upgrade.
7. Click the Set Change State icon ( ) and
move to the home menu on the product.
English
1
Network Services
BD-LIve™
Network Services
8. To select a device, use the RED(A) or
BLUE(D) button to select a file to play.
(For playing back Video, Music or Photos files,
see pages 45~53.)
Application Program at a Glance
6
1
SAMSUNG PC Share Manager
File
Share
Server
Help
Server : PC Share Manager
2345
My Computer
C: Document and settings Admin
You Tube
internet radio service
Please activate Internet@TV
to enjoy a variety of Internet Services.
No Disc
a Change Device
d View Devices
Name
Folder 1
" Enter
✎ NOTE
 Depending on te performance of the external
modem or router, HD video may not play
properly.
not locate your PC on the TV screen.
- The Background Music and Background
Music Setting functions.
- Sorting files by preference in the Photo,
Music, and Movie folders.
- The Change Group function.
- The Safe Remove function.
 The Sorting method may differ depending on
the sever function.
 The search and skip operation may differ
depending on the sever function.
 During video playback, play time will not
display.
 To use AllShare function, please locate both
this product and PC in same subnet.
English
Kind
File
Folder 2
File
Folder 3
File
Folder
Folder 1
Full Path
C: Document and settin..
7
1
Menu Bar
2
Share Folder Enabled icon : Use this if you
want to select a folder in your PC to share.
3
Share Folder Disabled icon : Use this if you
want to set folder sharing off.
4
Refresh icon : Use this if you want to refresh
list of folders and files in My Computer.
5
Update icon : Select a folder to share and
don’t forget to press this button.
The updated state will be applied to the server.
6
Server : Displays the name of the sharing
server.
7
Shared Folder : Displays a list of the shared
folders.
8
My Computer : Displays a list of the folders
and files in the PC.
 AllShare does not support the following
functions.
Size
8
 If your system uses a firewall, the product may
Shared Folder
06
Other information
Refer to the chart below when this product does not function properly. If the problem you are
experiencing is not listed below or if the instruction below does not help, turn off the product,
disconnect the power cord, and contact the nearest authorized dealer or Samsung Electronics Service
Centre.
Symptom
Check/Remedy
I cannot eject the disc.
• Is the power cord plugged securely into the outlet?
• Turn off the power and then turn it back on.
The iPod fails to connect.
• Check the condition of the iPod connector and Dock.
• Keep the iPod S/W version up to date.
Playback does not start.
• Check the region number of the BD/DVD.
BD/DVD discs purchased from abroad may not be playable.
• CD-ROMs and DVD-ROMs cannot be played on this Product.
• Make sure that the rating level is correct.
Playback does not start
immediately when the
Play/Pause button is pressed.
• Are you using a deformed disc or a disc with scratches on the surface?
• Wipe the disc clean.
Sound is not produced.
• N o sound is heard during fast playback, slow playback, and step motion playback.
• Are the speakers connected properly? Is the speaker setup correctly customized?
• Is the disc severely damaged?
Sound can be heard only from a
few speakers and not all 6.
• On certain BD/DVD discs, sound is output from the front speakers only.
• Check if the speakers are connected properly.
• Adjust the volume.
• When listening to a CD, radio or TV, sound is output to the front speakers only.
Select "PRO LOGIC II" by pressing
PL II (Dolby Pro Logic II) on the remote
control to use all six speakers.
Dolby Digital 5.1 CH Surround
Sound is not produced.
• Is there "Dolby Digital 5.1 CH" mark on the disc? Dolby Digital 5.1 CH Surround Sound is
produced only if the disc is recorded with 5.1 channel sound.
• Is the audio language correctly set to Dolby Digital 5.1-CH in the information
display?
The remote control does not work.
• Is the remote control being operated within its operation range of angle and distance?
• Are the batteries drained?
• H ave you selected the mode(TV/BD) functions of the remote control (TV or BD) correctly?
• Disc is rotating but no
picture is produced.
• Is the TV power on?
• Are the video cables connected properly?
• Is the disc dirty or damaged?
• A poorly manufactured disc may not be playable.
• Picture quality is poor and
picture is shaking.
Audio language and subtitles do
not work.
• A udio language and subtitles will not work if the disc does not contain them.
Menu screen does not appear
even when the menu function is
selected.
• Are you using a disc that does not contain menus?
English
63
Other information
Troubleshooting
Other information
Symptom
Check/Remedy
Aspect ratio cannot be changed.
• You can play 16:9 BD/DVDs in 16:9 Wide mode, 4:3 Letter Box mode, or 4:3
Pan - Scan mode, but 4:3 BD/DVDs can be seen in 4:3 ratio only. Refer to the
Blu-ray Disc jacket and then select the appropriate function.
• The product is not working.
(Example: The power goes out
or a strange noise is heard.)
• Turn off the power, and press and hold the STOP (  ) button on the product
for longer than 5 seconds with no disc inserted.
• The Product is not working
normally.
The rating level password has
been forgotten.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
• With no disc in the product, press and hold the product's STOP (  ) button for
longer than 5 seconds. INIT appears on the display and all settings will return
to the default values.
And then press the POWER button.
- Using the RESET function will erase all stored settings.
Do not use this unless necessary.
Can't receive radio broadcasts.
• Is the antenna connected properly?
• If the antenna's input signal is weak, install an external FM antenna in an area
with good reception.
While listening to TV audio
through the Product, no sound is
heard.
• If the OPEN/CLOSE ( ) button is pressed while listening to TV audio using the
D.IN or AUX functions, the BD/DVD functions are turned on and the TV audio is
muted.
"Not Available" appears on
screen.
• The features or action cannot be completed at this time because:
1. The BD/DVD’s software restricts it.
2. The BD/DVD’s software doesn’t support the feature (e.g., angles)
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
If the HDMI output is set to a
resolution your TV cannot support
(for example, 1080p), you may not
see a picture on your TV.
• Press and hold the STOP (  ) button on front panel for more than 5 seconds
with no disc inserted. All settings will revert to the factory settings.
No HDMI output.
• Check the connection between the TV and the HDMI jack of the Product.
• Check if your TV supports 576p(480p)/720p/1080i/1080p HDMI input
resolution.
Abnormal HDMI output screen.
• If random noise appears on the screen, it means that TV does not support
HDCP (High-bandwidth Digital Content Protection).
If the HDMI output is set to a resolution
your TV cannot support (for example,
1080p), you may not see a picture on
your TV.
• Press and hold the STOP (@) button on front panel for more than 5 seconds
with no disc inserted. All settings will revert to the factory settings.
64
English
• When the factory default settings are restored, all the user data stored in the
BD data will be deleted.
06
Other information
Symptom
Check/Remedy
PC Share Manager function
I can see folders shared through
the PC Share Manager, but I
cannot see the files.
• Since it shows only files corresponding to the Image, Music, and Movie
categories, files that do not correspond to these categories may not be
displayed.
AllShare function
Video is played intermittently.
• Check if the network is stable.
• Check if the network cable is properly connected and if the network is not
overloaded.
• Wireless connection between the server and the product is unstable.
Check the connection.
AllShare connection between TV
and PC is unstable.
• IP address under the same subnetwork should be unique, otherwise IP collision
can results in such a phenomenon.
• Check if you have a firewall enabled.
If so, disable the firewall function.
BD-LIVE
I cannot connect to the BD-LIVE
server.
• Check whether the network connection is successful or not by using Network
Test menu. (See page 42)
• Check whether the USB memory device is connected with product or not.
• The memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 37)
• Please check whether the BD-LIVE Internet Connection menu is set to
Allow(All).
• If all above fails, contact the contents provider or update the latest firmware.
When using the BD-LIVE service,
an error occurs.
• T he memory device must have at least 1GB of free space to accommodate the
BD-LIVE service.
You can check the available size in BD Data Management. (See page 37)
✎ NOTE
 When the factory default settings are restored, all the user data stored in the BD data will be deleted.
English
65
Other information
Specifications
General
FM Tuner
Weight
Dimensions
Operating Temperature Range
Operating Humidity Range
Signal/noise ratio
Usable sensitivity
Total harmonic distortion
BD (Blu-ray Disc)
DVD (Digital Versatile Disc)
Disc
CD : 12cm (COMPACT DISC)
CD : 8cm (COMPACT DISC)
Composite Video
Video Output
Component Video
3.5 kg
430 (W) x 63 (H) x 325 (D) mm
+5°C to +35°C
10 % to 75 %
70 dB
10 dB
0.5 %
Reading Speed : 4.917m/sec
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time (Single Sided, Single Layer Disc) : 135 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
1 channel : 1.0 Vp-p (75 Ω load)
Blu-ray Disc : 576i(480i)
DVD : 576i(480i)
Y : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
Blu-ray Disc : 1080i, 720p, 576p(480p), 576i(480i)
DVD : 576p(480p), 576i(480i)
Video/Audio
Amplifier
HDMI
Front speaker output
Centre speaker output
Surround speaker output
Subwoofer speaker output
Frequency response
S/N Ratio
Channel separation
Input sensitivity
1080p, 1080i, 720p, 576p(480p)
PCM multichannel audio, Bitstream audio, PCM audio
165W x 2(3Ω)
170W(3Ω)
165W x 2(3Ω)
170W(3Ω)
Analogue input
20Hz~20kHz (±3dB)
Digital input
20Hz~44kHz (±3dB)
70dB
60dB
(AUX)500mV
HT-C5500
Speaker system
Speaker
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Dimensions (W x H x D)
Weights
66
English
5.1ch speaker system
Front
Surround
Centre
3Ω
3Ω
3Ω
140Hz~20kHz 140Hz~20kHz 140Hz~20kHz
87dB/W/M
87dB/W/M
87dB/W/M
165W
165W
170W
330W
330W
340W
Front : 90 x 207.5 x 68.5 mm
Surround : 90 x 141.5 x 68.5 mm
Centre : 360 x 74.5 x 68.5 mm
Subwoofer : 168 x 350 x 295 mm
Front : 0.67 kg, Surround : 0.58 kg
Centre : 0.57 kg, Subwoofer : 3.80 kg
Subwoofer
3Ω
40Hz ~ 160Hz
88dB/W/M
170W
340W
06
Speaker system
Speaker
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Dimensions (W x H x D)
5.1ch speaker system
Front
Surround
Centre
Subwoofer
3Ω
3Ω
3Ω
3Ω
140Hz~20kHz 140Hz~20kHz 140Hz~20kHz 40Hz ~ 160Hz
87dB/W/M
87dB/W/M
87dB/W/M
88dB/W/M
165W
165W
170W
170W
330W
330W
340W
340W
Front : 90 x 1300 x 119 mm (Stand base : 250 x 250 mm)
Surround : 90 x 141.5 x 68.5 mm
Centre : 360 x 74.5 x 68.5 mm
Subwoofer : 168 x 350 x 295 mm
Front : 3.27 kg, Surround : 0.58 kg
Centre : 0.57 kg, Subwoofer : 3.80 kg
Weights
HT-C5550W
Speaker system
Speaker
Impedance
Frequency range
Output sound pressure level
Rated input
Maximum input
Dimensions (W x H x D)
5.1ch speaker system
Front
Surround
Centre
Subwoofer
3Ω
3Ω
3Ω
3Ω
140Hz~20kHz 140Hz~20kHz 140Hz~20kHz 40Hz ~ 160Hz
87dB/W/M
87dB/W/M
87dB/W/M
88dB/W/M
165W
165W
170W
170W
330W
330W
340W
340W
Front : 90 x 1300 x 119 mm (Stand base : 250 x 250 mm)
Surround : 90 x 1300 x 119 mm (Stand base : 250 x 250 mm)
Centre : 360 x 74.5 x 68.5 mm
Subwoofer : 168 x 350 x 295 mm
Front : 3.27 kg, Surround : 2.88 kg
Centre : 0.57 kg, Subwoofer : 3.80 kg
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications without notice.
- Weight and dimensions are approximate.
- Design and specifications are subject to change without prior notice.
- For the power supply and Power Consumption, refer to the label attached to the product.
Weights
SWA-5000
Weight
Dimensions (W x H x D)
Operating Temperature Range
Operating Humidity Range
Output
1.1 kg
Frequency range
76.2 x 228 x 152 mm
+5°C to +35°C
10% ~ 75%
165W x 2 CH
20Hz~20KHz
S/N Ratio
65dB
English
67
Other information
HT-C5530W
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre.
North America
Area
Contact Center 
CANADA
1-800-SAMSUNG (726-7864)
MEXICO
01-800-SAMSUNG (726-7864)
U.S.A
1-800-SAMSUNG (726-7864)
Latin America
Area
Contact Center 
ARGENTINE
0800-333-3733
0800-124-421
BRAZIL
4004-0000
CHILE
800-SAMSUNG (726-7864)
Nicaragua
00-1800-5077267
Honduras
800-7919267
COSTA RICA
0-800-507-7267
ECUADOR
1-800-10-7267
EL SALVADOR 800-6225
GUATEMALA
1-800-299-0013
JAMAICA
1-800-234-7267
PANAMA
800-7267
PUERTO RICO 1-800-682-3180
REP. DOMINICA 1-800-751-2676
TRINIDAD &
1-800-SAMSUNG (726-7864)
TOBAGO
VENEZUELA
0-800-100-5303
COLOMBIA
01-8000112112
CIS
Area
Contact Center 
RUSSIA
8-800-555-55-55
Georgia
8-800-555-555
Armenia
0-800-05-555
Azerbaijan
088-55-55-555
KAZAKHSTAN 8-10-800-500-55-500
UZBEKISTAN
8-10-800-500-55-500
KYRGYZSTAN 00-800-500-55-500
TADJIKISTAN 8-10-800-500-55-500
UKRAINE
0-800-502-000
Belarus
810-800-500-55-500
Moldova
00-800-500-55-500
Middle East & Africa
Area
Contact Center 
Turkey
444 77 11
SOUTH AFRICA 0860-SAMSUNG (726-7864)
U.A.E
800-SAMSUNG (726-7864)
Bahrain
8000-4726
Jordan
800-22273
Egypt
0800-726786
KSA
9200-21230
Qatar
800-2255
Syria
1825-22-73
Web Site
www.samsung.com
www.samsung.com
www.samsung.com
Web Site
www.samsung.com
www.samsung.com
Europe
Area
AUSTRIA
BELGIUM
CZECH
DENMARK
FINLAND
FRANCE
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
GERMANY
www.samsung.com
SPAIN
www.samsung.com
www.samsung.com
SWEDEN
U.K
EIRE
Web Site
www.samsung.com
www.samsung.com/kz_ru
www.samsung.com/kz_ru
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/hk
www.samsung.com/hk_en/
Web Site
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
HUNGARY
ITALIA
LUXEMBURG
NETHERLANDS
NORWAY
POLAND
PORTUGAL
SLOVAKIA
Switzerland
LITHUANIA
LATVIA
ESTONIA
Contact Center 
0810 - SAMSUNG
Web Site
www.samsung.com
www.samsung.com/be (Dutch)
www.samsung.com/be_fr (French)
800 - SAMSUNG (800-726786) www.samsung.com
70 70 19 70
www.samsung.com
030 - 6227 515
www.samsung.com
01 48 63 00 00
www.samsung.com
01805 - SAMSUNG
www.samsung.com
02-201-24-18
06-80-SAMSUNG (726-7864)
800-SAMSUNG (726-7864)
261 03 710
0900-SAMSUNG
www.samsung.com
www.samsung.com
www.samsung.com
815-56 480
0 801 1SAMSUNG (172678)
022-607-93-33
80820-SAMSUNG (726-7864)
0800-SAMSUNG (726-7864)
902 - 1 - SAMSUNG
(902 172 678)
0771 726 7864 (SAMSUNG)
0845 SAMSUNG (7267864)
0818 717100
0848 - SAMSUNG
(7267864, CHF 0.08/min)
8-800-77777
8000-7267
800-7267
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com
www.samsung.com/ch
www.samsung.com/ch_fr/ (French)
www.samsung.com
www.samsung.com
www.samsung.com
Asia Pacific
Area
Contact Center 
Web Site
AUSTRALIA
1300 362 603
www.samsung.com
New zealand 0800 SAMSUNG (0800 726 786) www.samsung.com
CHINA
400-810-5858 / 010-6475 1880 www.samsung.com
www.samsung.com/hk
Hong Kong
(852) 3698-4698
www.samsung.com/hk_en/
3030 8282
1800 110011
INDIA
www.samsung.com
1800 3000 8282
1800 266 8282
0800-112-8888
INDONESIA
www.samsung.com
021-5699-7777
JAPAN
0120-327-527
www.samsung.com
MALAYSIA
1800-88-9999
www.samsung.com
1-800-10-SAMSUNG (726-7864)
1-800-3-SAMSUNG (726-7864)
PHILIPPINES
www.samsung.com
1-800-8-SAMSUNG (726-7864)
02-5805777
SINGAPORE
1800-SAMSUNG (726-7864)
www.samsung.com
1800-29-3232
THAILAND
www.samsung.com
02-689-3232
TAIWAN
0800-329-999
www.samsung.com
VIETNAM
1 800 588 889
www.samsung.com
AH68-02258K
Download PDF

advertising