Samsung | KENOX X700 | Samsung L700 User Manual

Instructions
Getting to know your camera
■ Use this camera in the following order
Set up the camera driver
Take a picture
Insert the USB cable
Before connecting the camera to a PC, via
the USB cable, you will need to set up the
camera driver. Install the camera driver
that is contained in Application software
CD-ROM. (p.64)
Take a picture. (p.15)
Insert the supplied USB cable into the
PC’s USB port and the camera’s USB
connection terminal. (p.66)
Check the camera’s power
Check the camera’s power. If the power is
turned off, press the camera button to turn
it on.
Check [Removable Disk]
Open Window’s EXPLORER and search
for [Removable Disk]. (p.67)
Thank you for buying a Samsung Digital Camera.
● Prior to using this camera, please read the user manual thoroughly.
● If you require After Sales service, please bring the camera and the cause of the
camera malfunction (such as battery, Memory card etc.) to the A/S centre.
● Please check that the camera is operating properly prior to when you intend to
use it (e.g. for a trip or an important event) to avoid disappointment. Samsung
camera takes no responsibility for any loss or damages that may result from
camera malfunction.
● Keep the manual in a safe place.
● If you use a card reader to copy the images on the memory card to your PC, the
images could be damaged. When transferring the images taken with the camera
to your PC, be sure to use the supplied USB cable to connect the camera to
your PC. Please note that the manufacturer accepts no responsibility for loss or
damage of images on the memory card due to the use of a card reader.
● The contents and illustrations of this manual are subject to change without prior
notice for upgrading the camera functions.
● If your camera was purchased outside of the country where you wish to have,
servicing fees are charged by the manufacturer's representatives in that country.
● In some countries where this camera is not in market, servicings may not be
available.
Microsoft, Windows and Windows logo are registered trademarks of Microsoft
Corporation incorporated in the United States and/or other countries.
All brand and product names appearing in this manual are registered trademarks
of their respective companies.
● If you use a card reader to copy the images on the memory card to your PC, the
images could be damaged. When transferring the images taken with the camera
to your PC, be sure to use the supplied USB cable to connect the camera to
your PC. Please note that the manufacturer holds no responsibility for loss or
damage of images on the memory card due to the use of a card reader.
《1》
Danger
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
■ Do not attempt to modify this camera in any way. This may result in fire, injury,
electric shock or severe damage to you or your camera. Internal inspection,
maintenance and repairs should be carried out by your dealer or Samsung
Camera Service centre.
■ Please do not use this product in close proximity to flammable or explosive
gases, as this could increase the risk of explosion.
■ Should any form of liquid or a foreign object enter the camera, do not use it.
Switch off the camera, and then disconnect the power source. You must contact
your dealer or Samsung Camera Service centre. Do not continue to use the
camera as this may cause a fire or electric shock.
■ Do not insert or drop metallic or inflammable foreign objects into the camera
through access points e.g. the memory card slot and battery chamber. This may
cause a fire or electric shock.
■ Do not operate this camera with wet hands. This could pose a risk of electric
shock.
《2》
Warning
WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
■ Do not use the flash in close proximity to people or animals. Positioning the flash
too close to your subject’s eyes may cause eyesight damage.
■ For safety reasons keep this product and accessories out of reach of children or
animals to prevent accidents e.g.:
•Swallowing battery or small camera accessories. If an accident should occur,
please consult a doctor immediately.
•There is the possibility of injury from the camera’s moving parts.
■ Battery and camera may become hot during prolonged use and it may result in
camera malfunction. Should this be the case, allow the camera to sit idle for a
few minutes to allow it time to cool.
■ Do not leave this camera in places subject to extremely high temperatures, such
as a sealed vehicle, direct sunlight or other places of extreme variances in
temperature. Exposure to extreme temperatures may adversely affect the
camera’s internal components and could cause a fire.
■ When in use, do not cover the camera or Charger. This may cause heat to build
up and distort the camera body or cause a fire. Always use the camera and its
accessories in a well-ventilated area.
Caution
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in a minor or moderate injury.
■ Leaking, overheating, or burst battery could result in fire or injury.
•Use battery with the correct specification for the camera.
•Do not short circuit, heat or dispose of battery in fire.
•Do not insert the battery with the polarities reversed.
■ Remove the battery when not planning to use the camera for a long period of
time. Battery may leak corrosive electrolyte and permanently damage the
camera’s components.
■ Do not fire the flash while it is in contact with hands or objects. Do not touch the
flash after using it continuously. It may cause burns.
■ Take care not to touch the lens or lens cover to avoid taking an unclear image
and possibly causing camera malfunction.
■ Avoid obstructing the lens or the flash when you capture an image.
■ Credit cards may be demagnetized if left near case. Avoid leaving magnetic strip
cards near the case.
Contents
READY
●System chart
●Identification of features
■Front & Top
■Back & Bottom
■Bottom / 5-function button
■Self-timer lamp
■Camera Status Lamp
■Mode icon
●Connecting to a Power Source
●Inserting the memory card
●Instructions on how to use the
memory card
5
6
6
7
8
8
8
9
9
10
11
RECORDING
●LCD monitor indicator
13
14
●Changing the recording mode
14
■Selecting the [MODE] menu
■Changing the recording mode 14
15
●Starting the recording mode
15
■How to use the Auto mode
■How to use the Movie clip mode 16
■Recording the movie clip without
16
sound
■Pausing while recording a movie clip
16
(Successive Recording)
16
■Using Successive Recording
■How to use the Program mode 17
17
■How to use the Scene modes
■How to use the VOICE
18
RECORDING mode
●Things to Watch Out for When
18
Taking Pictures
●Using the camera buttons to set the
19
camera
19
■POWER button
19
■Shutter button
19
■ZOOM W / T button
19
■TELE Zoom
20
■WIDE Zoom
■Voice recording / Voice memo / UP
21
button
21
■Recording a voice memo
21
■Macro / Down button
22
■Focus lock
22
■Flash / Left button
24
■Self-timer / Right button
25
■MENU / OK button
25
■M (Mode) button
26
■E (Effect) button
27
■Special Effect : Colour
■Special Effect :
27
Preset focus frames
28
■Movie Clip frame stabiliser
《3》
Contents
■+ / - button
●Using the LCD monitor to set the
camera settings
■How to use the menu
■Mode Set
■Mode
■Size
■Quality / Frame rate
■Metering
■Continuous shot
■Sharpness
■OSD (On Screen Display)
information
29
31
32
33
33
34
34
35
35
35
36
PLAY
●Starting play mode
36
37
■Playing back a movie clip
37
■Movie clip capture function
37
■How to capture the movie clip
37
■On camera movie trimming
■Playing back a recorded voice 38
38
●LCD monitor indicator
●Using the camera buttons to adjust
38
the camera
38
■Play mode button
■Thumbnail / Enlargement button 39
40
■Voice memo / Up button
《4》
■Play & Pause / Down button
■Left / Right / Menu / OK button
■E (Effect) button
■Delete button
●Setting up the play back function
using the LCD monitor
■Starting the slide show
■On Screen Display information
■Rotating an image
■Resize
■Protecting images
■Deleting images
■Copy To Card
■DPOF
■DPOF : STANDARD
■DPOF : Index
■DPOF : Print size
■PictBridge
■PictBridge : Picture Selection
■PictBridge : Print Setting
■PictBridge : Print
■PictBridge : RESET
41
41
41
41
42
44
45
45
46
46
47
47
48
48
48
49
49
50
50
51
52
SETUP
●Setup menu
■File name
■Auto power off
■Language
■Format
■Setting up the Date / Time / Date
type
■World Time
■Imprinting the recording date
■Auto Focus lamp
■Sound
■Connecting an External Device
(USB)
■LCD brightness
■Selecting Video out type
■Quick view
■Initialisation
●Setting up the Mycam menu
■Start up image
■Start up sound
■Shutter sound
●Important notes
●Warning indicator
●Before contacting a service centre
●Specifications
54
54
55
55
55
55
55
55
56
56
56
56
57
57
57
57
58
59
60
61
SOFTWARE
52
53
54
●Software Notes
●System Requirements
●About the software
63
63
63
●Setting up the application software
●Starting PC mode
●Removing the removable disk
●Setting up the USB Driver for MAC
●Using the USB Driver for MAC
●Removing the USB Driver for
Windows 98SE
●Digimax Master
●FAQ
64
66
68
68
68
69
69
72
System chart
Please check that you have the correct contents before using this product. The contents can vary depending on the sales region. To buy the optional equipment, contact your
nearest Samsung dealer or Samsung service centre.
< Included items >
Camera case
DPOF compatible
printer (see p.48)
User manual,
Product warranty
Camera strap
Software CD
(see p.63)
SD memory card / MMC
(see p.12)
Computer
(see p.66)
PictBridge compatible
printer (see p.49)
USB cable
AV cable
Rechargeable battery
(SLB-0837)
AC cord
Charger
(SBC-L5)
External monitor
(see p. 56)
《5》
Identification of features
Front & Top
Shutter button
Power button
Speaker
Flash
Self-timer lamp /
Auto focus lamp
Lens
Microphone
《6》
Identification of features
Back & Bottom
Camera status lamp
Zoom W button
(Thumbnail)
Zoom T button
(Digital zoom)
M (Mode) button
LCD monitor
Strap eyelet
E (Effects) button
+ / - button, Delete button
AV OUT/ USB
5 function button
Tripod socket
Play mode button/Printer button
《7》
Identification of features
■ Self-timer lamp
Bottom / 5-function button
Icon
Memory card slot
Status
Battery holder
Blinking
Blinking
Blinking
Description
- For the first 7 seconds, the lamp blinks at 1 second intervals.
- For the final 3 seconds, the lamp blinks quickly at 0.25second intervals.
For the 2 seconds, the lamp blinks quickly at 0.25-second
intervals.
A picture will be taken after about 10 seconds and 2
seconds later a second picture will be taken.
■ Camera Status Lamp
Battery chamber cover
Battery chamber
Status
Voice memo / Voice Recording / Up button
Menu / OK button
Flash /
Left button
Self-timer /
Right button
Macro / Down button
Play & Pause button
《8》
Description
The lamp turns on and off when the camera is
Power on
ready to take a picture
The lamp blinks while saving the image data and
After taking a picture
turns off when the camera is ready to take a picture
The lamp lights up
When the USB cable is
(LCD monitor turns off after initializing the device)
inserted to a PC
Transmitting Data with a PC The lamp blinks (LCD monitor turns off)
When the USB cable is
inserted to a printer
When the printer is printing
The lamp is off
The lamp blinks
Identification of features
■ Mode icon : Refer to page 14 for more information about the camera mode setting.
MODE MOVIE CLIP VOICE RECORDING
AUTO
PROGRAM
PLAY
ICON
MODE
SCENE
NIGHT
PORTRAIT CHILDREN LANDSCAPE
TEXT
CLOSE UP
ICON
MODE SUNSET
DAWN
BACKLIGHT FIREWORKS BEACH&SNOW
ICON
-
Connecting to a Power Source
■ You should use the rechargeable battery (SLB-0837) supplied with the camera.
■ SLB-0837 rechargeable battery Specification
Model
Type
Capacity
Voltage
Charging time
SLB-0837
Lithium Ion
860mAh
3.7V
Approx. 150 MIN (Using the SBC-L5)
■ Number of images and battery life: Using the SLB-0837
Still image
Battery life
Number of images
Approx. 85 MIN
Approx. 170
Based
on
the
following
shooting
conditions
Using the fully charged battery, Auto mode
7M image size, Fine image quality
Shot to shot interval : 30Sec.
Changing the zoom position
between the Wide and the Tele ends every
1 shot.
Using the flash every two times
Movie
Recording time
Approx. 70 MIN
Using the fully charged battery
Based
640X480 image size
on
30fps frame rate
the
following
shooting
conditions
※These figures are measured under Samsung’s standard conditions and Shooting
conditions and may vary depending on the way of user’s usage.
INFORMATION
Important information about battery usage
● When the camera is not in use, turn off the camera power.
● Please remove the battery if the camera will not be used for long periods.
The battery can lose power over time and may leak if kept inside the
camera.
● Low temperatures (below 0°C) can affect the performance of the battery
and you may experience reduced battery life.
● Battery will usually recover at normal temperatures.
● During extended use of the camera, the camera body may become warm.
This is perfectly normal.
《9》
Connecting to a Power Source
■ Insert the battery as shown
- If the camera does not turn on after you
have inserted battery, please check
whether the battery is inserted with the
correct polarity (+ / -).
- When the battery chamber cover is
opened, do not press the battery
chamber cover by force. This may cause
damage to the battery chamber cover.
■ There are 4 indicators for battery condition that are displayed on the LCD
monitor.
Battery
indicator
Battery
status
《10》
Low battery
Low battery
Low battery
capacity
capacity
capacity
The battery is
(Prepare to
(Prepare to
(Prepare to
fully charged
recharge or use recharge or use recharge or use
spare battery) spare battery) spare battery)
Inserting the memory card
■ Insert the memory card as shown.
- Turn off the camera’s power before
inserting the memory card.
- Have the front of the memory card
facing toward the front of the camera
(lens) and the card pins toward the
back of the camera (LCD monitor).
- Do not insert the memory card in the
wrong way round. Doing so may
damage the memory card slot.
Instructions on how to use the memory card
● Be sure to format the memory card (see p.54) if you are using a newly
purchased memory for the first time, if it contains data that the camera cannot
recognise, or if it contains images captured with a different camera.
● Turn off the camera power whenever the memory card is being inserted or
removed.
● Repeated use of the memory card will eventually reduce the memory card’s
performance. Should this be the case, you will need to purchase a new memory
card. Wear and tear on the memory card is not covered by the Samsung
warranty.
● The memory card is an electronic precision device.
Do not bend, drop or subject the memory card to any heavy impact.
● Do not store the memory card in an environment with strong electronic or
magnetic fields, e.g. near loud speakers or TV receivers.
● Please do not use or store in an environment where there are extremes in
temperature.
● Do not allow the memory card to become dirty or to come into contact with any
liquid. Should this happen, clean the memory card with a soft cloth.
● Please keep the memory card in its case when not in use.
● During and after periods of extended use, you may notice that the memory card
is warm. This is perfectly normal.
● Do not use a memory card that is used in another digital camera. To use the
memory card in this camera, format the memory card using this camera.
● Do not use a memory card formatted by another digital camera or memory card
reader.
● If the memory card is subjected to any of the following, the recorded data may
become corrupted :
- When the memory card is used incorrectly.
- If the power is switched off or the memory card is removed while recording,
deleting (formatting) or reading.
● Samsung cannot be held responsible for lost data.
● It is advisable to copy important data onto other media as back-up e.g. floppy
disks, hard disks, CD etc.
● If there is insufficient memory available :
A [Memory Full!] message will appear and the camera will not operate. To
optimise the amount of memory in the camera, replace the memory card or
delete unnecessary images stored on the memory card.
《11》
Instructions on how to use the memory card
INFORMATION
● Don't remove the memory card when the camera status lamp is blinking as
this may cause damage to data in the memory card.
■ When using a 256MB MMC memory, the specified shooting capacity will be as
follows. These figures are approximate as image capacities can be affected by
variables such as subject matter and memory card type.
Recorded image size Super Fine
7M
76
■ The camera can use SD/ SDHC Memory Cards and MMC (Multi Media Cards).
Please consult the enclosed manual for using the MMC Cards.
Card pins
Write protect
switch
Label
[SD (Secure Digital) memory card]
《12》
The SD/ SDHC memory card has a write
protect switch that prevents image files
from being deleted or formatted. By sliding
the switch to the bottom of the SD memory
card, the data will be protected. By sliding
the switch to the top of the SD memory
card, the data protection will be cancelled.
Slide the switch to the top of the SD
memory card before taking a picture.
Fine
113
Normal
193
30FPS
-
15FPS
-
Still
image
5M
93
159
272
-
-
3M
173
266
425
-
-
1M
560
673
743
-
-
*Movie
clip
640
-
-
-
About 11'
About 18'
320
-
-
-
About 40'
About 67'
※ The recording times can be changed by the zoom operation.
The zoom button doesn’t use during the movie recording.
LCD monitor indicator
■ The LCD monitor displays information about the shooting functions and selections.
①
No.
4
⑳
⑲
②
⑱
③
⑰
Description
Icons
Page
Flash
p.22~24
Without Sound
p.16
5
Self-timer
p.24
6
Macro
p.21~22
7
Metering
p.35
8
Card inserted indicator
-
④
⑯
9
Auto focus frame
-
⑤
⑮
⑭
10
Camera shake warning
p.18
11
Date / Time
⑬
12
Exposure compensation
⑫
13
White Balance
p.30
14
ISO
p.29
⑥
⑦
⑧
⑨ ⑩
⑪
[Image & Full Status]
No.
1
Description
Icons
Page
Recording mode
2
Battery
3
Continuous shot
AEB
2007.01.01 01:00 PM
p.55
p.31
15
RGB
16
Sharpness
RGB
p.29
p.35
17
Image quality
p.34
18
Image size
p.34
Number of available shots remaining
12
p.12
Remaining time (Movie clip / Voice recording)
00:01:30/ 01:00:00
p.12
p.15~18
19
p.10
20
Voice memo
p.21
21
Optical/ Digital Zoom bar/
Digital Zoom rate
p.19~20
p.35
《13》
Changing the recording mode
■ You can select the desired working mode by the M (mode) button located on the
back of the camera and [MODE], [MODE SET] menu. Auto, Program, movie
clip, scene (night, portrait, children, landscape, text recognition, close-up, sunset,
dawn, backlight, fireworks, beach & snow) camera modes are available.
● Selecting the [MODE] menu
1. Insert the battery (p.10).
2. Insert the memory card (p.10). As this camera has a 20MB internal memory, it
is not essential to insert the memory card. If the memory card is not inserted,
an image will be stored in the internal memory. If the memory card is inserted,
an image will be stored on the memory card.
3. Close the battery chamber cover.
4. Press the power button to turn on the camera.
MODE
STILL & MOVIE
5. Press the menu button and a menu will display.
FULL
6. Use the Left / Right button to select the [MODE]
menu.
7. Select [STILL & MOVIE] or [FULL] sub menu by
pressing the UP / DOWN button.
- [STILL & MOVIE] : A still image mode that was selected on the [MODE SET]
menu and movie clip mode can be selected.
Refer to page 51 for more information about using the
[MODE SET] menu.
- [FULL]
: Auto, Program, Movie clip and scene modes can be
selected.
8. Press the MENU button and the menu will disappear.
《14》
● Changing the recording mode : If the [STILL & MOVIE] menu was selected
Steps from 1-4 are the same as those for selecting the [MODE] menu.
5. The recording mode of still image selected in the [MODE SET] menu will
display.
6. Press the M (Mode) button located on the back of the camera and the
recording mode will change to the movie clip mode.
7. Press the M (Mode) button again and a still image mode selected on the
[MODE SET] menu will be selected.
[Pressing the M (Mode) button]
[AUTO mode]
[MOVIE CLIP mode]
Changing the recording mode
● Changing the recording mode : If the [FULL] menu was selected
Steps from 1-4 are the same as those for selecting the [MODE] menu.
5. The recording mode of still image selected in the [MODE SET] menu will
display.
6. Press the M (Mode) button located on the back of the camera and the mode
selection menu will display.
7. To select the Auto, Program, Movie clip or Scene modes, press the Left /
Right button.
To move between the Auto, Manual, Movie clip menu line and Scene menu
line, press the Up / Down button.
Starting the recording mode
■ How to use the Auto mode(
)
Use this for shooting basic still images.
1. Select the [FULL] sub menu on the [MODE]
menu (p.14).
2. Select the Auto mode by pressing the M (Mode)
button (p.15).
3. Point the camera towards the subject and
compose the image by using the LCD monitor.
4. Press the shutter button to capture an image.
[AUTO mode]
INFORMATION
AUTO
[Pressing the Left button]
MOVIE
Confirm:Mode/OK
Confirm:Mode/OK
[Mode selection menu]
[Selecting the Movie clip mode]
●If the auto focus frame turns to red when you press the shutter button down
half way, it means that the camera cannot focus on the subject. Should this
be the case, the camera is less likely to capture an image clearly.
●Avoid obstructing the lens or the flash when you capture an image.
Portrait
[Pressing the Up button]
Confirm:Mode/OK
[Selecting the Scene mode]
8. Press the M (Mode) button to select the mode and the mode selection menu
will disappear.
《15》
Starting the recording mode
■ How to use the Movie clip mode(
)
A movie clip can be recorded for as long as the available recording time of the
memory capacity allows.
1. Select the [FULL] sub menu on the [MODE] menu
(p.14).
2. Select the Movie clip mode by pressing the M
(Mode) button (p.15).
3. Point the camera towards the subject and
compose the image by using the LCD monitor.
[MOVIE CLIP mode]
4. Press the shutter button once and movie clips are
recorded for as long as the available recording time allows. Movie clips will still
be recorded if the shutter button is released.
If you wish to stop recording, press the shutter button again.
※ Image size and type are listed below.
- Image size
: 640X480, 320X240 (user selectable)
- Movie clip file type : AVI (MPEG-4)
■ Recording the movie clip without sound
You can record the movie clip without sound.
Steps from 1-3 are the same as those for MOVIE
CLIP mode.
4. Press the Up button and the (
) icon will
display on the LCD monitor.
5. Press the shutter button and movie clip is
recorded for as long as the available recording
time without sound.
6. To stop the recording, press the shutter button again.
《16》
■ Pausing while recording a movie clip (Successive Recording)
This camera allows you to temporarily stop during unwanted scenes, while
recording a movie clip. Using this function, you can record your favourite scenes
into a movie clip without having to create multiple movie clips.
● Using Successive Recording
Steps from 1-2 are the same as those for MOVIE
CLIP mode.
3. Point the camera towards the subject and
compose the image by using the LCD monitor.
Press the shutter button and movie clips are
Stop:Shutter REC: /
recorded for as long as the available recording
time. Movie clips will still be recorded if the shutter [Successive recording of a movie clip]
button is released.
4. Press the Pause button (
) to pause recording.
5. Press the Pause button (
) again to resume the recording.
6. If you wish to stop recording, press the shutter button again.
Starting the recording mode
■ How to use the Program mode(
)
Selecting the automatic mode will configure the camera with optimal settings
and you can manually configure various functions.
1. Select the [FULL] sub menu on the [MODE] menu
(p.14).
2. Select the Program mode by pressing the M
(Mode) button (p.15).
3. Point the camera towards the subject and
compose the image by using the LCD monitor.
[PROGRAM mode]
4. Press the shutter button to capture an image.
■ How to use the Scene modes(
)
Use the menu to easily configure optimal settings for a variety of shooting
situations.
1. Select the [FULL] sub menu on the [MODE]
menu (p.14).
2. Select the Scene mode by pressing the M
(Mode) button (p.15).
3. Point the camera towards the subject and
compose the image by using the LCD monitor.
[SCENE mode]
4. Press the shutter button to capture an image.
※ The scene modes are listed below.
[NIGHT] (
)
: Use this for shooting still images at night or in other
dark conditions.
[PORTRAIT] (
)
: To take a picture of a person.
[CHILDREN] (
)
: To take a picture of fast moving objects, for
example, children.
[LANDSCAPE] (
) : To take pictures of distant scenery.
[TEXT] (
)
: Use this mode to shoot a document.
[CLOSE UP] (
)
: Close-up shooting for small objects such as plants
and insects.
[SUNSET] (
)
: For taking pictures of sunsets.
[DAWN] (
)
: Daybreak scenes.
[BACKLIGHT] (
)
: Portrait without shadows caused by backlight.
[FIREWORKS] (
) : Firework scenes.
[BEACH&SNOW] (
) : For ocean, lake, beach and snowscape scenes.
《17》
Starting the recording mode
■ How to use the VOICE RECORDING mode (
)
A voice recording can be recorded for as long as the
memory capacity allows. (Max. 1hour)
1. In any mode with the exception of Movie clip mode,
select the VOICE RECORDING mode by pressing
the Voice recording button twice.
2. Press the shutter button to record a voice.
- Press the shutter button once and voice is
recorded for as long as the available recording
time allows. The recording time will be displayed
on the LCD monitor. Voice will still be recorded if
REC:Shutter
EXIT:
the shutter button is released.
- If you wish to stop recording, press the shutter
[VOICE RECORDING mode]
button again.
- File type : *.wav
* A distance of 40cm between you and the camera
(microphone) is the best distance to record
sound.
《18》
Things to Watch Out for When Taking Pictures
■ Pressing the shutter button down half way.
Lightly press the shutter button to confirm focus and flash battery charge.
Press the shutter button all way down to take the picture.
[Lightly press the shutter button]
[Press the shutter button]
■ The available memory capacity may vary depending on shooting conditions and
camera settings.
■ When the Flash Off or Slow synchro mode is selected in a low lighting condition, the
camera shake warning indicator (
) may appear on the LCD monitor. In this case,
use a tripod, support the camera on a solid surface or change to flash shot mode.
■ Shooting against the light :
Please do not take pictures to the sunlight direction. Taking a picture against the
sun may make the picture dark. To take a picture against the sun, please use the
[Backlight] in the scene shooting mode (see page 17), fill-in flash (see page 23),
spot metering (see page 35), or exposure compensation (see page 31).
■ Avoid obstructing the lens or the flash when you capture an image.
■ Compose the image by using the LCD monitor.
■ Under certain conditions the auto focus system may not perform as expected.
- When photographing a subject that has little contrast.
- If the subject is highly reflective or shiny.
- If the subject is moving at high speed.
- When there is strong reflected light, or when the background is very bright.
- When the subject matter has only horizontal lines or the subject is very narrow
(such as a stick or flagpole).
- When the surroundings are dark.
Using the camera buttons to set the camera
■ The recording mode function can be set up by using the camera buttons.
ZOOM W / T button
● If the menu is not displayed, this button works
as the OPTICAL ZOOM or DIGITAL ZOOM
button.
POWER button
● Used for turning the camera’s power on / off.
● If there is no operation during the specified time,
the camera's power will be turned off
automatically to save battery life.
Refer to page 54 for more information about the
auto power off function.
● This camera has a 3X optical zoom and a 5X digital zoom function.
Using both will offer a total zoom ratio of 15X.
● TELE Zoom
Optical zoom TELE
Digital zoom TELE
Shutter button
● Used for taking an image or recording voice in
the RECORDING mode.
● In MOVIE CLIP mode :
Pressing the shutter button down fully starts the
process for recording a movie clip. Press the
shutter button once and the movie clip is
recorded for as long as the available recording
time in the memory allows. If you wish to stop recording, press the shutter button
again.
● In STILL IMAGE mode
Pressing the shutter button down halfway activates the autofocus and checks
the condition of the flash. Pressing the shutter button down fully takes and stores
the image. If you select voice memo recording, the recording will start after the
camera has finished storing the image data.
: Pressing the ZOOM T button. This will zoom into the
subject i.e. the subject will appear nearer.
: When the maximum (3X) optical zoom is selected,
pressing the ZOOM T button activates the digital zoom
software. Releasing ZOOM T button stops the digital
zooming at the required setting. Once the maximum
digital zoom (5X) is achieved, pressing the ZOOM T
button will have no effect.
Pressing
the ZOOM
T button
[WIDE zoom]
Pressing
the ZOOM
T button
[TELE zoom]
[Digital zoom 5.0X]
《19》
ZOOM W / T button
● WIDE Zoom
Optical zoom WIDE
INFORMATION
: Pressing the ZOOM W button. This will zoom out from
the subject i.e. the subject will appear further away.
Pressing the ZOOM W button continuously will set the
camera to its minimum zoom setting i.e. the subject
appears at its furthest from the camera.
Pressing
the ZOOM
W button
[Optical zoom 2X]
[TELE zoom]
Digital zoom WIDE
Optical zoom
Digital zoom
Pressing
the ZOOM
W button
: When the digital zoom is in operation, pressing the
ZOOM W button will reduce the digital zooming in
steps. Releasing ZOOM W button stops digital
zooming. Pressing the ZOOM W button will reduce the
digital zoom and then it will continue to reduce the
optical zoom until the minimum setting is reached.
Pressing
the ZOOM
W button
[Digital zoom 5.0X]
《20》
[WIDE zoom]
Pressing
the ZOOM
W button
[TELE zoom]
[WIDE zoom]
● Images taken using the digital zoom may take a little longer for the camera
to process. Allow time for this to take place.
● The digital zoom cannot be used in movie clip shots.
● You may notice a decrease in image quality when using the digital zoom.
● To view a clearer digital zoom image, press the shutter button halfway at the
maximum (3X) optical zoom position and press the zoom T button again.
● The digital zoom can't be activated in the Night scene mode, Children
mode, Text mode, two scene modes (Close up, Fireworks) and the movie
clip mode.
● Take care not to touch the lens to avoid taking an unclear image and
possibly causing camera malfunction. If the image is dim, turn the camera
power off and on again to modify the lens position.
● Take care not to press the lens as this may cause a camera malfunction.
● When the camera is turned on, take care not to touch the camera's moving
lens parts as this may cause the resulting image to be dim and unclear.
Voice recording (
) / Voice memo (
) / UP button
■ While the menu is showing, press the UP button to move up the sub menu.
When the menu is not displayed on the LCD monitor, the UP button operates as
the voice recording or voice memo ( ) button. You can add your voice-over to
a stored still image. Refer to page 18 for more information about the voice
recording.
Macro (
) / Down button
■ While the menu is showing, press the DOWN button to move from the main
menu to a sub menu, or to move down the sub menu. When the menu is not
showing, you can use the MACRO / DOWN button to take macro pictures.
The distance ranges are shown below. Press the Macro button until the desired
macro mode indicator displays on the LCD monitor.
● Recording a voice memo
1. Select a RECORDING mode with the exception of MOVIE CLIP mode. (p.15, 17)
2. Press the VOICE MEMO (
) button. If the voice memo indicator is
displayed on the LCD monitor, the setting is completed.
[Auto focus - No icon]
Stop:Shutter
[Preparing for Voice Memo]
[Recording Voice Memo]
3. Press the shutter button and take a picture. The picture is stored on the
memory card.
4. Voice memo will be recorded for ten seconds from the moment the picture is
stored. In the middle of the sound recording, pressing the shutter button will
stop the voice memo.
INFORMATION
● A distance of 40cm between you and the camera (microphone) is the best
distance to record sound.
[Macro (
)]
[Auto macro (
(Unit : cm)
■ Types of focus modes and focus ranges (W : Wide, T : Tele)
Mode
Auto (
Focus Type Auto macro (
Focus range
W : 5~Infinity
T : 40~Infinity
)
)
Normal
W : 80~Infinity
T : 80~Infinity
Program (
Macro (
W : 5~80
T : 40~80
)]
)
)
Normal
W : 80~Infinity
T : 80~Infinity
INFORMATION
● When the macro mode is selected, it is possible that camera shake will
occur. Take care not to shake the camera.
● When you take a picture within 20cm in the Macro mode, select the FLASH
OFF mode.
《21》
Macro (
) / Down button
Flash (
■ When the menu is displayed on the LCD monitor,
pressing the LEFT button makes the cursor shift to
the left tab.
■ Available focusing method, by recording mode
(O : Selectable, X : Not selectable, ∞ : Infinity focus range)
Mode
Normal
Macro
Auto macro
O
O
X
O
X
O
SCENE
Mode
Normal
Macro
Auto macro
) / Left button
O
O
X
■ When the menu is not displayed on the LCD
monitor, the LEFT button operates as the FLASH
(
) button.
O
O
O
∞
X
X
∞
∞
O
∞
X
X
X
X
X
O
X
X
X
X
X
X
X
X
X
O
X
X
X
X
X
X
O
[Selecting the Auto flash]
● Selecting the flash mode
1. Select a RECORDING mode with the exception of MOVIE CLIP mode. (p.15, 17)
2. Press the Flash button until the desired flash mode indicator displays on the
LCD monitor.
3. A flash mode indicator will be displayed on the LCD monitor.
Use the correct flash to suit the environment.
Focus lock
■ To focus on a subject not positioned in the centre of the picture, use the focus lock function.
● Using the Focus Lock
1. Ensure the subject is in the centre of the autofocus frame.
2. Press the SHUTTER button halfway. When the green auto focus frame lights
up, it means the camera is focused on the subject. Be careful not to press the
SHUTTER button all the way down to avoid taking an unwanted picture.
3. With the SHUTTER button still pressed down only halfway, move the camera
to recompose your picture as desired, and then press the SHUTTER button
completely to take the picture. If you release your finger from the SHUTTER
button, the focus lock function will be cancelled.
1. The image to be
captured.
《22》
2. Press the SHUTTER
button halfway and
focus on the subject.
3. Recompose the picture
and fully depress the
SHUTTER button.
● Flash range
ISO
AUTO
Normal
WIDE
TELE
0.8 ~ 3.0 0.8 ~ 2.5
(Unit : m)
Macro
WIDE
TELE
0.4 ~ 0.8 0.5 ~ 0.8
Auto macro
WIDE
TELE
0.4 ~ 3.0 0.5 ~ 2.5
Flash (
) / Left button
INFORMATION
● If you press the shutter button after selecting the Auto, Fill-in, Slow sychro
flash, the first flash fires to check the shooting condition (Flash range and
Power ratio of flash).
Do not move until the second flash fires.
● Using the flash frequently will reduce the life of the battery.
● Under normal operating conditions the charging time for the flash is
normally less than 4 seconds. If the battery is weak, the charging time will
be longer.
● Take photographs within the flash range.
● The image quality is not guaranteed if the subject is too close or highly
reflective.
● When taking an image in a poorly lit condition with the flash, there may be a
white speck in the captured image. The speck is caused by the reflecting of
the flash light from the atmospheric dust. It is not camera malfunction.
● Flash mode indicator
Menu tab
Flash mode
Auto flash
Auto &
Red eye
reduction
Description
If the subject or background is dark, the camera
flash will operate automatically.
If a subject or background is dark, the camera flash
will work automatically and will reduce the red-eye
effect by using the red-eye reduction function.
Fill in flash
The flash fires regardless of available light.
The intensity of the flash will be controlled,
according to the prevailing conditions. The brighter
the background or subject is, the less intense the
flash will be.
Slow synchro
The flash will operate in conjunction with a slow
shutter speed in order to obtain the correct
exposure. When you take an image in a condition
with poor light, the camera shake warning indicator
(
) will display on the LCD monitor.
We recommend using a tripod for this function.
Flash off
The flash does not fire. Select this mode when
capturing images in a place or situation where flash
photography is prohibited. When you capture an
image in a poorly lit condition, the camera shake
warning indicator (
) will display on the LCD
monitor.
We recommend using a tripod for this function.
《23》
Flash (
) / Left button
● Available flash mode, by recording mode (O : Selectable X : Not selectable)
X
X
O
X
X
X
X
X
X
X
X
X
X
O
X
O
O
X
O
O
X
X
X
X
X
X
X
X
X
X
O
X
X
X
X
X
X
X
X
O
X
X
X
X
O
O
X
X
X
X
X
X
X
X
X
X
O
O
O
O
O
O
O
O
O
O
O
X
O
X
Self-timer (
) / Right button
■ When the menu is displayed on the LCD monitor, pressing the Right button
makes the cursor shift to the right tab.
■ When the menu is not displayed on the LCD monitor, the RIGHT button
operates as the Self-timer (
) button. This function is used when the
photographer would also like to be in the image.
● Selecting the self-timer
1. Select a RECORDING mode with the exception of
VOICE RECORDING mode. (p.15~17)
2. Press the SELF-TIMER button until the desired
mode indicator displays on the LCD monitor.
A 10 second, 2 second or double self-timer icon
appears on the LCD monitor. In Movie Clip mode,
only the 10-second self-timer will work.
•10SEC self-timer (
):
Pressing the shutter button will allow an interval
of 10 seconds before the image is taken.
•2SEC self-timer (
):
Pressing the shutter button will allow an interval
[Selecting the 10 SEC self-timer]
of 2 seconds before the image is taken.
•Double self-timer (
):
A picture will be taken after about 10 seconds and 2 seconds later a
second picture will be taken. When using the flash, the 2-second self-timer
may be delayed for longer than 2 seconds depending on the flash charging
time.
3. When you press the SHUTTER button, the picture will be taken after the
specified time has elapsed.
INFORMATION
● If you operate the Power button, Self-timer button, Shutter button or Play
mode button during the self-timer operation, the self-timer function is
cancelled.
● Use a tripod to prevent the camera from shaking.
● In Movie Clip mode, only the 10SEC self-timer will work.
《24》
MENU / OK button
M (Mode) button
■ MENU button
- When you press the MENU button, a menu related to each camera mode will
be displayed on the LCD monitor. Pressing it again will return the LCD to the
initial display.
- A menu option can be displayed when the followings are selected :
MOVIE CLIP and STILL IMAGE mode. There is no menu available when the
VOICE RECORDING mode is selected.
■ You can select the desired recording mode. The selectable recording modes are
different from what you selected sub menu in the [MODE] menu.
- [STILL & MOVIE] : A recording mode selected in the [MODE SET] menu,
Movie clip mode
- [FULL]
: Auto, Movie clip, Program, Scene modes
● How to use the mode button : In case of [STILL & MOVIE] and [AUTO] sub
menu
SIZE
[Pressing the MENU button]
[Menu off]
3072x2304
2592x1944
2048x1536
1024x768
[Pressing the M button]
[Menu on]
[Auto mode]
[Movie clip mode]
■ OK button
- When the menu is displayed on the LCD monitor, this button is used for shifting
the cursor to the sub menu or for confirming data.
《25》
M (Mode) button
E (Effect) button
● How to use the mode button : In case of [FULL] sub menu and Auto mode
■ It is possible to add special effects to your images by using this button
■ Still image mode : You can select the colour and focus menus.
Movie clip mode : You can select the colour and stabilizer menus.
■ Available Effects, by recording mode (O : Selectable X : Not selectable)
[Auto mode]
O
O
O
O
O
O
O
X
X
O
X
X
X
X
O
X
X
X
X
X
X
Program
[Pressing the Mode button]
Confirm:Mode/Ok
[Pressing the Right button]
[Program mode]
■ Even if the camera is turned off, the special effect setting will be preserved.
To cancel the special effect, select the
sub menu in the Colour menu and
select the
sub menu in the rest special effect menu.
Auto
Confirm:Mode/Ok
[Mode selection menu]
Movie
[Pressing the Left button]
Confirm:Mode/Ok
[Movie cliip mode]
[Pressing the Up button]
Night
Confirm:Mode/Ok
[Scene mode]
《26》
※ This button will not operate in the Voice recording mode and some scene modes
(Night, Text, Sunset, Dawn, Backlight, Fireworks and Beach & Snow)
Portrait
[Pressing the Left / Right button]
Confirm:Mode/Ok
[Selecting a scene mode]
Special Effect : Colour
Special Effect : Preset focus frames
■ By using the camera’s digital processor, it is possible to add special effects to
your images.
1. Press the E button in the available camera modes.
2. Select the (
) menu tab by pressing the Left / Right button.
Normal
[Still image mode]
■ You can make the subject stand out from its
surroundings. The subject will be sharp and in focus
while making the rest out of focus.
1. Press the E button in the Program mode.
2. Select the (
) menu tab by pressing the Left /
Right button.
3. Select a desired sub menu by pressing the Up /
Down button and press the OK button.
HighLight
Normal
[Movie clip mode]
HighLight
3. Select a desired sub menu by pressing the Up / Down button and press the
OK button.
: No effect is added to the image
: Captured images will be stored in black and white.
: Captured images will be stored in a sepia tone
(a gradient of yellowish brown colours).
: Captured images will be stored in a blue tone.
: Captured images will be stored in a red tone.
: Captured images will be stored in a green tone.
: Save the image in negative mode.
[Range 1]
HighLight
[Range 2]
HighLight
[Range 3]
HighLight
[Range 4]
4. The preset focus frame will appear.
Press the shutter button to capture an image
Capture:SH
Edit:+/-
4. Press the shutter button to capture an image.
《27》
Special Effect : Preset focus frames
● Moving and changing the focus frame
You can change the focus frame after selecting a Range menu.
1. Point the camera towards the subject and compose the image by using the
LCD monitor.
2. Press the + / - button.
3. The colour of focus frame turns white. Press the Up / Down / Left / Right
button to move the focus frame position.
4. To select the focus frame position, press the + / - button again and you can
take a picture.
Pressing the + / - button
Capture:SH
Edit:+/-
Capture:SH
Move:
[The frame is activated]
Capture:SH
Move:
[After changing the frame position]
《28》
● How to use this function
1. Press the E button in the Movie clip mode.
2. Select the STABILISER menu by pressing the
Left / Right button.
3. Select a desired sub menu by pressing the Up /
Down button and press the OK button.
Stabilizer
: Movie clip frame stabiliser function
becomes disabled.
: Prevents camera shake during movie recording.
The recording frame range will become narrower than when you
select the
menu. Pre-view frames may not display smoothly on
the LCD monitor.
●When you select the
sub menu, the movie clip frame range will be
narrow depending on the movie clip size.
Pressing the + / - button
Edit:+/-
■ This function helps stabilise images captured during movie recording.
You can select this menu only in the MOVIE CLIP mode.
If the memory card is not inserted, this function will not operate.
INFORMATION
Pressing the
Up / Down / Left /
Right button
Capture:SH
Movie Clip frame stabiliser
+ / - button
■ You can use the + / - button to adjust the values for the RGB, ISO, white balance
and exposure compensation.
Main menu
Sub menu
RGB
R (Red), G (Green), B (Blue)
ISO
AUTO, 50, 100, 200, 400, 800, 1600
Available camera mode
AUTO, DAYLIGHT, CLOUDY,
WHITE BALANCE FLUORESCENT H, FLUORESCENT L,
TUNGSTEN, CUSTOM.
Exposure compensation
-2.0 ~ 0.0 ~ +2.0 (0.5EV steps)
■ RGB : Allows the user to adjust the R (Red), G (Green), and B (Blue) values of
the images to be captured.
● Setting RGB Values
1. Press the + / - button, and then use the UP and
DOWN buttons to select the RGB icon (
).
The RGB menu bar will appear as shown.
2. Use the UP / DOWN / LEFT and RIGHT
buttons to select the desired RGB value.
- Up / Down Button : Navigates between R, G,
and B icons.
- Left / Right Button : Changes value of each icon.
3. When you press the + / - button again, the value you set will be saved and
RGB setup mode will end.
※ When special effect (colour) from the icon other than
be able to select the RGB.
■ ISO : You can select the ISO sensitivity when taking pictures.
The speed or specific light-sensitivity of a camera is rated by ISO numbers.
● Selecting an ISO Sensitivity
1. Press the + / - button, and then use the UP and
DOWN buttons to select the ISO icon (
).
The ISO menu bar will appear as shown.
2. Use the LEFT and RIGHT buttons to select the
desired ISO sensitivity value.
- AUTO :
The camera's sensitivity is automatically
changed by variables such as lighting value or subject brightness.
- 50, 100, 200, 400, 800, 1600 :
You can increase the shutter speed while the same amount of light is
present, by increasing the ISO sensitivity. However, the image may be
saturated in high luminance. The higher the ISO value, the higher the
camera’s sensitivity to light is and therefore the greater its capacity to take
pictures in dark conditions. However, the noise level in the image will
increase as the ISO value increases, making the image appear coarse.
3. When you press the + / - button again, the value you set will be saved and
ISO setup mode will end.
is selected, it will not
《29》
+ / - button
■ White balance : The white balance control allows you to adjust the colours to
appear more natural.
● Selecting a White Balance
1. Press the + / - button, and then use the UP
and DOWN buttons to select the white
balance icon (
). The white balance
menu bar will appear as shown.
2. Use the LEFT and RIGHT buttons to set the
white balance to the desired value. The value
you set wil be displayed on the LCD monitor.
AUTO
: The camera automatically selects the appropriate
white balance settings, depending on the prevailing
lighting conditions.
DAYLIGHT
: For taking images outside.
CLOUDY
: For taking images under a cloudy and overcast sky.
Fluorescent H
: For shooting under daylight fluorescent types of threeway fluorescent lighting.
Fluorescent L
: Shooting under white fluorescent lighting.
TUNGSTEN
: For shooting under tungsten (standard light bulb) lighting.
CUSTOM
: Allows the user to set the white balance according to
the shooting condition.
Different lighting conditions may cause a colour cast on your images.
3. Press the + / - button again. The value you set will be saved and White
Balance setup mode will end.
《30》
● Using the Custom White Balance
White balance settings may vary slightly depending on the shooting
environment.
You can select the most appropriate white balance setting for a given shooting
environment by setting up the custom white balance.
1. Select the CUSTOM (
) menu of the
White Balance.
2. Place a sheet of white paper in front of the
camera so that the LCD monitor shows only
white, and then press the SHUTTER button.
3. Your custom white balance value is stored.
- The custom white balance value will be
applied, starting with the next picture you
take.
- The user configured white balance will be
remain effective until it is overwritten.
Measure:Shutter
[White paper]
+ / - button
■ Exposure compensation : This camera automatically adjusts the exposure
according to the ambient lighting conditions.
You can also select the exposure value by using the
+ / - button.
Using the LCD monitor to set the camera settings
■ You can use the menu on the LCD monitor to set up recording functions.
The items indicated by
are default settings.
Menu tab Main menu
Sub menu
Auto
● Compensating Exposure
1. Press the + / - button, and then use the UP and
DOWN buttons to select the exposure
compensation icon (
).
The exposure compensation menu bar will
appear as shown.
2. Use the LEFT and RIGHT buttons to set the
desired exposure compensation factor.
3. Press the + / - button again. The value you set will be saved and the Exposure
Compensation setup mode will close.
If you change the exposure value, the exposure indicator (
) will be
displayed on the bottom of the LCD monitor.
※ A negative exposure compensation value reduces the exposure.
Note that a positive exposure compensation value increases the exposure
and the LCD monitor will appear white or you may not get good pictures.
MODE SET
MODE
SIZE
(Still image)
SIZE
(Movie clip)
Camera working mode Page
Program
Movie
Night
Portrait
Children
Landscape
Text
Close up
Sunset
Dawn
Backlight
Firework
Beach&Snow
Still & Movie
Full
3072X2304
2592X1944
2048X1536
1024X768
640X480
320X240
p.33
p.33
p.34
p.34
《31》
Using the LCD monitor to set the camera settings
Menu tab Main menu
QUALITY
FRAME RATE
METERING
SHOOTING
SHARPNESS
OSD
INFORMATION
Sub menu
Camera working mode Page
Super Fine
Fine
Normal
-
30 FPS
15 FPS
Multi
Spot
Single
Continuous
AEB
-
Soft
Normal
Vivid
-
Full
Basic
LCD Save
-
p.34
How to use the menu
1. Turn on the camera and press the MENU button. A menu for each camera
mode appears. However, there is no menu for Voice Recording mode (
).
2. Use the LEFT and RIGHT buttons to navigate through the menus.
p.34
MODE SET
Auto
Program
Movie
Night
Portrait
Move:
p.35
p.35
Exit:MENU
Press the
LEFT or
RIGHT button.
Press the
LEFT or
RIGHT button.
MODE
STILL & MOVIE
FULL
SIZE
3072x2304
2592x1944
2048x1536
1024x768
3. Use the UP and DOWN buttons to select a sub menu.
p.35
MODE SET
p.36
Move:
Auto
Program
Movie
Night
Portrait
Set:OK
Press the
UP or DOWN
button.
MODE SET
Move:
Auto
Program
Movie
Night
Portrait
Set:OK
Press the
UP or DOWN
button.
MODE SET
Move:
※ Menus are subject to change without prior notice.
4. Select a sub menu, and then the value you set will be saved.
Press the MENU button and the menu will disappear.
《32》
Program
Movie
Night
Portrait
Children
Set:OK
Mode Set
■ You can select the desired recording mode.
[Auto]
[Program]
: For shooting basic still image
MODE SET
: You can still manually configure all
Auto
Program
functions except the aperture value
Movie
and shutter speed.
Night
Portrait
[Movie]
: For taking a movie clip
Move:
Set:OK
[Night]
: Use this for shooting still images at
night or in other dark conditions.
[Portrait]
: To take a picture of a person.
[Children]
: To take a picture of fast moving objects, for example, children.
[Landscape] : To take pictures of distant scenery.
[Text]
: Use this mode to shoot a document.
[Close up]
: Close-up shooting for small objects such as plants and insects.
[Sunset]
: For taking pictures of sunsets.
[Dawn]
: Daybreak scenes.
[Backlight] : Portrait without shadows caused by backlight.
[Firework]
: Firework scenes.
[Beach & Snow] : For ocean, lake, beach and snowscape scenes.
Mode
■ You can select the desired working mode using the M (Mode) button located on
the back of the camera in the [MODE] menu.
[STILL & MOVIE] : A still image mode that was
selected on the [MODE SET]
menu and movie clip mode can
be selected.
[FULL]
: Auto, Program, Movie clip and
scene modes can be selected.
MODE
STILL & MOVIE
FULL
INFORMATION
● When [Night], [Landscape], [Text], [Close up], [Sunset], [Dawn] and
[Firework] scene mode are selected, it is possible that camera shake will
occur.
《33》
Size
Quality / Frame rate
■ You can select the image size appropriate for your application.
Mode
Icon
Size
STILL IMAGE mode
7M
5M
3M
1M
3072X2304 2592X1944 2048X1536 1024X768
MOVIE CLIP mode
640
320
640X480
320X240
■ You can select the compression ratio appropriate for your application of the
captured images. The higher the compression ratio, the lower the picture quality.
QUALITY
FRAME RATE
Super Fine
Fine
30 FPS
15 FPS
Normal
SIZE
3072x2304
2592x1944
2048x1538
1024x768
[STILL IMAGE mode]
SIZE
640X480
320X240
[STILL IMAGE mode]
[MOVIE CLIP mode]
[MOVIE CLIP mode]
INFORMATION
● This file format complies with the DCF (Design rule for Camera File system).
INFORMATION
● High resolution images use more memory than lower resolution shots.
Therefore the higher the resolution selected the fewer will be the number of
shots available.
《34》
Metering
■ If you cannot obtain suitable exposure conditions, you can change the metering
method to take brighter pictures.
- Multi : Exposure will be calculated based on an
METERING
average of the available light in the image
Multi
Spot
area. However, the calculation will be
biased towards the centre of the image
area. This is suitable for general use.
- Spot : Only the rectangular area in the centre of
the LCD monitor will be metered for light.
This is the preferable setting when you want the subject in the centre of
the image exposed correctly, regardless of the back lighting.
INFORMATION
● If the subject is not the centre of the focus area, do not use the spot
metering as this may result in an exposure error. In this circumstance, it is
better to use exposure compensation.
Continuous shot
■ Select the number of pictures in continuous shooting.
- Single
: Take one picture only
SHOOTING
- Continuous : Images will be taken continuously
Single
until the shutter button is released.
Continuous
AEB
The shooting capacity depends on
the memory available.
- AEB
: Take three pictures in a series in
different exposures: short exposure
(-0.5EV), standard exposure (0.0EV) and over exposure (+0.5EV).
Use this mode if it is hard to decide exposure of the object.
※ High resolution and picture quality increases file saving time, which increases
stand-by time.
※ If fewer than 3 pictures are available in the memory, the AEB shooting is not available.
※ It is best to use a tripod for the AEB shooting as the time to save each image
file is longer and the blurring caused by camera shake may occur.
Sharpness
■ You can adjust the sharpness of the picture you are
about to take. You cannot check the sharpness
effect on the LCD monitor before you take a picture,
because this function is applied only when the
captured image is stored on the memory.
SHARPNESS
Soft
Normal
Vivid
- Soft
: The edges of the image are softened.
This effect is suitable for editing images
on your PC.
- Normal : The edges of the image are sharp.
This is suitable for printing.
- Vivid
: The edges of the image are emphasized. The edges will appear
sharp, but noise may occur in the recorded image.
《35》
OSD (On Screen Display) information
■ In any mode with the exception of VOICE
RECORDING mode, you can check the recording
status in the LCD monitor.
OSD INFORMATION
Full
Basic
LCD Save
■ Idle mode : If you select the [LCD Save] and the
camera isn't operated during the specified
time(about 30 SEC.), the camera power
will be idle (LCD monitor : OFF, Camera status lamp : Blinking)
automatically.
- To use the camera again, press any of the camera buttons except the power
button.
- If there is no operation during the specified time, the camera power will be
turned off automatically to save battery life. Refer to page 54 for more
information about the auto power off function.
Starting play mode
■ Turn the camera on and select Play mode by pressing the play mode button
(
). The camera can now play back the images stored in the memory.
■ If the memory card is inserted in the camera, all the camera functions apply only
to the memory card.
■ If the memory card is not inserted in the camera, all the camera functions apply
only to the internal memory.
● Playing back a still image
1. Select the PLAY mode by pressing the
play mode button (
).
2. The last image stored on the memory is
displayed on the LCD monitor.
3. Select an image that you want to view by
pressing the LEFT / RIGHT button.
※ Press and hold the LEFT or RIGHT
button to play back the images quickly.
INFORMATION
● Manner mode :To select the Manner mode, press the Playback mode
button for more than 3 seconds. In the Manner mode,
Shutter sound, Operating sound, Start-up sound and Effect
sound will not be generated. To cancel the Manner mode,
turn on the camera by pressing the Power button.
● Lightly press the shutter button in Play mode to switch to the currently set shooting mode.
《36》
Starting play mode
● Playing back a movie clip
1. Select the recorded movie clip that you want to play
back by using the LEFT / RIGHT button.
2. Press the play & pause button (
) to play back a
movie clip file.
- To pause a movie clip file while playing it back,
press the play & pause button again.
- Pressing the play & pause button again will cause
the movie clip file to restart.
- To rewind the movie clip while it is playing, press
the LEFT button. To fast forward the movie clip,
press the RIGHT button.
- To stop playback of the movie clip, press the play &
pause button, and then press the LEFT or RIGHT button.
■ On camera movie trimming : You can extract desired frames of a movie clip
during the movie clip play back.
● If the running time is under 10 seconds, the movie clip can’t be trimmed.
1. Press the Pause button at the point of the movie clip
that you want to start extracting.
2. Press the OK button. (The start point doesn't display
on the status bar, but the start point will be marked.)
MARK IN:OK Capture:E
3. Press the Play & Pause button and the extracted
range will be displayed on the status bar.
4. Press the Play & Pause button once more at the
point where you wish the extracted file to stop.
5. Press the OK button and a confirmation window will
be displayed.
PLAY:▶/ II
OK:Trim
6. Select a desired sub menu by pressing the
Left / Right button and press the OK button.
[Yes] : The extracted frames are saved as a new
Trimming?
file name.
Yes
No
[No] : The movie trimming will cancel.
Play:▶/ II
■ Movie clip capture function : capture still images from the movie clip.
● How to capture the movie clip
1. Press the Play & Pause button while playing the
movie clip. Then press the E button.
2. The paused movie clip is saved in a new file name.
※ The captured movie clip file has same size as the
original movie clip (640X480, 320X240).
Confirm:OK
MARK IN:OK
Capture:E
[Paused]
INFORMATION
● If the time line bar passes by the start point by pressing the REW (Left)
button, the first frame of the movie clip will display.
● If you don't specify the ending point of the movie clip, the trimming
confirmation window will display at the point of the last frame.
[Press the E button]
《37》
Starting play mode
● Playing back a recorded voice
1. Select the recorded voice that you want to play
back by using the LEFT / RIGHT button.
2. Press the play & pause button (
) to play
back a recorded voice file.
- To pause a recorded voice file, while playing it
back, press the play & pause button again.
- To resume playback of the voice file, press the play & pause button
- To rewind the voice file while it is playing, press the LEFT button. To fast
forward the voice file, press the RIGHT button.
- To stop playback of the voice file, press the play & pause button, and then
press the LEFT or RIGHT button.
LCD monitor indicator
■ The LCD monitor displays shooting information about the displayed image.
Play mode
Battery (p.10)
Voice Memo (p.40)
Protect indicator
(p.46)
DPOF indicator (p.48)
Folder name and
Stored image number
Using the camera buttons to adjust the camera
■ In Play mode, you can use the buttons on the camera to conveniently set up the
Play mode functions.
Play mode button
■ If you have turned on the camera by pressing the POWER button, you can press
the PLAY MODE button once to switch to Play mode and press it again to switch
to Recording mode.
■ You can turn the power on with the play mode button.
The camera is turned on in play mode. Press the play mode button again to turn
off the camera.
《38》
Thumbnail / Enlargement button
● You can view multiple pictures, enlarge a selected picture, and crop and save a
selected area of an image.
● Thumbnail display
1. While an image is displayed full screen, press
the thumbnail button.
2. The thumbnail display will highlight the image
that had been showing at the time the thumbnail
mode was selected.
3. Press the 5 function button to move to a desired image.
4. To view an image separately, press the enlargement button.
Pressing the thumbnail
button (
)
Pressing the enlargement
button (
)
● Image enlargement
1. Select an image that you want to enlarge and press the enlargement button.
2. Different parts of the image can be viewed by
pressing the 5 function button.
3. Pressing the thumbnail button will zoom back to
the original full sized image.
- You can tell whether the image displayed is an
enlarged view by checking the image
enlargement indicator shown at the bottom left
of the LCD monitor. (If the image is not an
enlarged view, the indicator will not be
displayed.) You can also check the area of
enlargement.
- Movie clips and WAV files can’t be enlarged.
- If an image is enlarged, a loss of quality may
occur.
Highlighted image
[Normal display mode]
[Thumbnail display mode]
● The maximum enlargement in proportion to the image size.
Image size
3072x2304
2592x1944
2048x1536
1024x768
Maximum
enlargement
X10.0
X8.1
X6.4
X3.2
《39》
Thumbnail / Enlargement button
● Trimming : You can extract part of the image and save it separately.
1. Select an image that you want to enlarge and press
the enlargement button.
Trimming?
2. Different parts of the image can be viewed by pressing
Yes
No
the 5 function button.
Confirm:OK
3. Press the MENU button and a message will be
displayed as shown alongside.
4. Select a desired sub menu by pressing the UP / DOWN button and press the
OK button.
[Yes] : The trimmed image will save as a new file name, and display on the
LCD monitor.
[No] : The trimming menu will disappear.
※ If there is insufficient memory space to save the trimmed image, the image
can’t be trimmed.
※ To delete the enlarged image on the LCD monitor, press the delete button.
《40》
Voice (
) memo / Up button
■ When the menu is displayed on the LCD monitor, the UP button operates as a
direction button.
■ When the menu is not displayed on the LCD monitor, the UP button operates as
the voice memo button. You can add your voice to a stored still image.
● Adding a Voice Memo to a Still Image
1. Press the LEFT / RIGHT button to select an image that
you wish to add sound to.
2. Press the voice memo button (
) and the voice
memo indicator will display. The camera is now ready
to record a voice memo.
3. Press the shutter button to start recording and voice
will be recorded to the still image for 10 seconds. While
the voice is recording, the recording status window will
be displayed as shown alongside. The recording can
be stopped by pressing the shutter button again.
4. The (
) icon will be displayed on the LCD monitor
after voice memo recording has finished.
- The voice memo will be saved in * .wav format, but
has the same file name as the still image to which it
corresponds.
- If you add a new voice memo to the still image that
already has a voice memo, the existing voice memo
will be erased.
Play & Pause (
) / Down button
■ In Play mode, the play & pause/ down button works as follows:
- If the menu is displayed
Press the DOWN button to move from the main menu to a sub menu, or to
move down the sub menu cursor.
- If a still image with a voice memo, a voice file, or a movie clip is playing
In Stop mode : Plays a still image with a voice memo, a voice file, or a movie clip.
During playback : Temporarily stops playback.
In Pause mode : Resumes playback
Left / Right / Menu / OK button
■ LEFT / RIGHT / MENU / OK buttons activate the following.
- LEFT button
: While the menu is showing, the LEFT button operates as a
direction button. While the menu is not showing, press the
LEFT button to select the previous image.
- RIGHT button : While the menu is showing, the RIGHT button operates as a
direction button. While the menu is not showing, press the
RIGHT button to select the next image.
- MENU button : When you press the MENU button, the play mode menu will
be displayed on the LCD monitor. Pressing it again will return
the LCD to the initial display.
- OK button
: When the menu is displayed on the LCD monitor, the OK
button is used for confirming data that is changed by using
the 5 function button.
E (Effect) button
■ By using the camera’s digital processor, it is possible to add special effects to
your images.
1. Press the E button.
2. Select a desired sub menu and press the OK button.
: Captured images will be stored in black and white.
: Captured images will be stored in a sepia tone.
: Captured images will be stored in a blue tone.
: Captured images will be stored in a red tone.
: Captured images will be stored in a green tone.
: Save the image in negative mode.
Delete (
Exit:E
) button
■ This deletes images stored on the memory card.
1. Select an image that you want to delete by pressing the LEFT / RIGHT button
and press the DELETE (
) button.
Delete?
Yes
No
Confirm:OK
Delete?
Yes
No
Confirm:OK
2. Select the sub menu values by pressing the Left / Right button and then press
the OK button.
If [Yes] is selected : deletes the selected images.
If [No] is selected : cancels "Delete Image".
《41》
Setting up the play back function using the LCD monitor
■ PLAY mode functions can be changed by using the LCD monitor. In the PLAY
mode, pressing the MENU button displays the menu on the LCD monitor.
The menus you can set up in Play mode are as follows. To capture an image
after setting up the play menu, press the PLAY mode button or shutter button.
Menu tab
Main menu
SLIDE
Sub menu
Secondary menu
Show
Play, Repeat Play
Interval
1, 3, 5, 10 sec
Effect
Music
OSD
INFORMATION
ROTATE
RESIZE
《42》
Off
Page
Menu tab
Main menu
PROTECT
DELETE
COPY TO CARD
p.44
DPOF
Off, Music1,2,3
Full
-
Basic
-
OSD Off
-
Right 90°
-
Left 90°
-
180°
-
Horizontal
-
Vertical
-
2592X1944
-
2048X1536
-
1024X768
-
User Image 1,2
-
p.45
p.45
p.46
Sub menu
Select
All Pics
Secondary menu
Page
Unlock/ Lock
p.46
Select
-
All Pics
-
No
-
Yes
-
Standard
Select/ All Pics/ Cancel
Index
No/ Yes
Size
Select/ All Pics/ Cancel
p.47
p.47
p.48~49
Setting up the play back function using the LCD monitor
■ This menu is available while the camera is connected to a PictBridge supporting
printer (direct connection to the camera, sold separately) with a USB cable.
Menu tab
Main menu
IMAGES
AUTO SET
Sub menu
One Pic
All Pics
No
Yes
Size
CUSTOM SET
Layout
Secondary menu
Auto
PostCard
Card
4X6
L
2L
Letter
A4
A3
Auto
Full
1
2
4
8
9
16
Index
Menu tab
Main menu
Page
Sub menu
Type
p.50
p.50
Quality
CUSTOM SET
Date
File Name
p.51
PRINT
DPOF PRINT
RESET
Standard
Index
No
Yes
No
Yes
Secondary menu
Auto
Plain
Photo
FastPhoto
Auto
Draft
Normal
Fine
Auto
Off
On
Auto
Off
On
-
Page
p.51
p.51
p.51
p.52
※ Menus are subject to change without prior notice.
《43》
Starting the slide show
■ Images can be displayed continuously at pre-set intervals. You can view the
slide show by connecting the camera to an external monitor.
1. Select the [Show] sub menu by pressing the UP /
SLIDE
DOWN button and press the RIGHT button.
Show
Play
2. Use the Up / Down buttons to select the desired
Interval
Repeat Play
Effect
sub menu.
Music
[Play] selected
: The slide show is closed
Back:
Set:OK
after one cycle.
[Repeat Play] selected : The slide show is repeated until cancelled.
3. Press the OK button to start the slide show.
- Press the Pause button to pause the slide show.
- Press the Pause button (
) again to resume the slide show.
- To stop the slide show, press the play & pause button, and then press the
LEFT or RIGHT button.
● Setting play interval : Set the slide show play interval.
1. Select the [Interval] sub menu by pressing the
UP / DOWN button and press the RIGHT button.
2. Use the Up / Down buttons to select the desired
interval.
3. Press the OK button to save the configuration.
SLIDE
Show
1 sec
Interval
3 sec
Effect
5 sec
Music
10 sec
Back:
INFORMATION
● The loading time depends on the image size and quality.
● While the slide show is playing, only the first frame of a MOVIE file is
displayed.
● While the slide show is playing, the voice recording file will not display.
《44》
Set:OK
● Configure slide show effects : Unique screen effects can be used for the slide
show.
1. Select the [Effect] sub menu by pressing the
SLIDE
UP / DOWN button and press the RIGHT button.
Show
Off
2. Use the Up / Down Button to select the type of
Interval
Effect
effect.
Music
: Normal display.
Back:
Set:OK
: Image is displayed slowly.
: Image is displayed slowly from the centre outwards.
: Image moves from the top left.
: The image slides diagonally from top left to bottom right.
: The image slides irregularly.
3. Press the OK button to confirm the setting.
● Setting the Music : Three types of music can be used
for the slide show.
1. Select the [Music] sub menu by pressing the UP /
DOWN button and press the RIGHT button.
2. Use the Up / Down Button to select the type of
music. (Off, Music 1~3)
3. Press the OK button to confirm the setting.
SLIDE
Show
Off
Interval
Music 1
Effect
Music 2
Music
Music 3
Back:
Set:OK
On Screen Display information
■ You can check shooting information about the displayed image.
1. Select a desired sub menu by pressing the
UP / DOWN button and press the OK button.
OSD INFORMATION
Full
Basic
OSD Off
Rotating an image
■ You can rotate the stored images by various degrees. Once the playback of the
rotated picture is finished, it will switch back to the original state.
1. Select a desired sub menu by pressing the
UP / DOWN button.
ROTATE
Right 90°
Left 90°
180°
Horizontal
Vertical
Exit:MENU
Move:
Av : F2.8
Tv : 1/60
ISO : 50
Flash:OFF
3072x2304
2007/02/01
[Full]
[Basic]
Av : F2.8
Tv : 1/60
ISO : 50
Flash:OFF
3072x2304
2007/02/01
[OSD Off]
Aperture value
Shutter speed
ISO value
Whether or not the flash is used
Size
Recording date
[Before rotating the image]
[Right 90°]
[Left 90°]
[180°]
[Horizontal]
[Vertical]
2. Press the OK button and the rotated image will be displayed. If you display the
rotated image on the LCD monitor, empty spaces may appear to the left and
right of the image.
《45》
Resize
Protecting images
■ Change the resolution (size) of pictures taken. Select the [User Image] to save
an image to be the start-up image. The resized image will have a new file name.
1. Select a desired sub menu by pressing the UP /
DOWN button and press the OK button.
RESIZE
2592x1944
2048x1536
1024x768
User Image 1
User Image 2
Exit:MENU
Move:
● Image Resize Types
Resize
2592X1944
2048X1536
1024X768
User Image 1,2
7M
5M
3M
1M
O
X
X
X
O
O
X
X
O
O
O
X
O
O
O
O
● A large sized image can be resized to a smaller sized image, but not vice versa.
● Only JPEG images can be resized. Movie clip (AVI), Voice recording (WAV) files
can’t be resized.
● You can change the resolution of only those files compressed in the JPEG 4:2:2
format.
● The resized image will have a new file name. The [User Image] image is stored
not on the memory card but on the internal memory.
● Only two [User Image] images can be saved.
● If the memory capacity is insufficient to store the resized image, the resized
image will not be stored.
《46》
■ This is used to protect specific shots from being accidentally erased (Lock).
It also unprotects images that have been previously protected (Unlock).
● Protecting Images
1. Select a desired sub menu by pressing the
UP / DOWN button and press the OK button.
[Select] : Selection window for an image to be
protected / released is displayed.
- Up / Down / Left / Right : Select an image
- Zoom W / T Button : Protect / release the image
- OK Button : Your changes will be saved and the
menu will disappear.
[All Pics] : Protect / release all saved images
- Zoom W / T Button :Protect / release the
images
- OK Button : Your changes will be saved and the
menu will disappear.
- If you protect an image, the protect icon will be
displayed on the LCD monitor.
(An unprotected image has no indicator)
- An image in LOCK mode will be protected from
the delete function, but will NOT be protected from
the format function.
PROTECT
Select
All Pics
Exit:MENU
W◀
W◀
Move:
Unlock
Set:OK
Unlock
Set:OK
▶T
▶T
Deleting images
Copy To Card
■ Of all the files stored in the memory card, the unprotected files in the DCIM
subfolder will be deleted. Remember that this will permanently delete
unprotected images. Important shots should be stored on a computer before
deletion takes place. The startup image and SKIN image are stored in the
camera's internal memory (i.e., not on the memory card) and it will not be
deleted even if you delete all files on the memory card.
● Deleting images
1. Select a desired sub menu by pressing the
UP / DOWN button and press the OK button.
[Select] : Selection window for an image to
delete is displayed.
- Up / Down / Left / Right : Select an image
- Zoom T Button : Select the image for deletion.
(V mark)
- OK Button : Press the OK Button to display the
confirmation message. Select the
[Yes] menu and press the OK
button to delete marked images.
[All Pics] : Displays confirmation window. Select
the [Yes] menu and press the OK
button to delete all unprotected
images. If there aren’t protected
images, all the images are deleted
and a [No Image!] message will
display.
2. After deletion, the screen will be changed to the
play mode screen.
DELETE
Select
All Pics
Exit:MENU
■ This enables you to copy image files, movie clips and voice recording files on the
camera's built-in internal memory to the camera's removable SD memory card.
● Copying to the Memory Card
1. Select a desired sub menu by pressing the
COPY TO CARD
UP / DOWN button and press the OK button.
No
Yes
- [No] : Cancels "Copy to Card".
- [Yes] : All images, movie clips and voice
recording files saved in the internal
Exit:MENU
Move:
memory are copied to the memory card
after the [Processing!] message is displayed. After copying has been
completed, the screen will return to play mode.
Move:
INFORMATION
Select:T
Del:OK
Delete?
Yes
No
Confirm:OK
● When this menu is selected without inserting a memory card, you can select
the [COPY TO CARD] menu but the menu can’t be run.
● If there is not enough space available in the memory card to copy saved
images in the internal memory (20MB), the [COPY TO CARD] command will
copy only some of the images and display [Memory Full!] message. Then the
system will return to the playback mode. Please be sure to delete any
unnecessary files to free up space before inserting the memory card into the
camera.
● When you move images from the internal memory to the removable SD
card, they will be automatically renumbered to avoid duplication of the file
name. If the last file in the memory card is SL270001.jpg, the copied file
names start from SL270002.jpg. After completing [COPY TO CARD], the
last stored image of the last copied folder is displayed on the LCD monitor.
《47》
DPOF
DPOF : Index
■ DPOF (Digital Print Order Format) allows you to embed printing information on
your memory card’s MISC folder. Select the pictures to be printed and how
many prints to make.
■ The DPOF indicator will display on the LCD monitor when an image that has
DPOF information plays back. Images can then be printed on DPOF printers, or
at an increasing number of photo labs.
■ This function is not available for Movie clips and Voice recording files.
■ If a memory card is not inserted, the menus are still displayed in the LCD, but are
not selectable.
DPOF : STANDARD
■ This function allows you to embed print quantity information on a stored image.
1. Select the [Standard] menu by pressing the
UP / DOWN button and press the RIGHT button.
2. Select a desired sub menu by pressing the
UP / DOWN button.
[Select] : Selection window for an image to print is
displayed.
- Up / Down / Left / Right : Select an image to print.
- Zoom W / T Button : Select the number of prints.
[All Pics] : Configure number of prints for all pictures
except movie and voice files.
- W / T button : Select a number of prints
[Cancel] : Cancel the print setup.
3. Press the OK button to confirm the setting.
If an image carries DPOF instructions, the DPOF
indicator (
) will show.
DPOF
Standard
Index
Size
Select
All Pics
Cancel
Back:
Set:OK
W◀
0 Prints
W◀
0 Prints
Set:OK
《48》
▶T
Set:OK
▶T
■ Images (except for movie clips and voice file) are printed as index type.
1. Select the [Index] menu by pressing the
UP / DOWN button and press the RIGHT button.
2. Select a desired sub menu by pressing the UP /
DOWN button.
If [No] is selected : Cancel the index print setting.
If [Yes] is selected : The image will be printed in
index format.
3. Press the OK button to confirm the setting.
DPOF
Standard
Index
No
Yes
Size
Back:
Set:OK
DPOF : Print size
PictBridge
■ You can specify the print size when printing images stored on the memory card.
The [Size] menu is available only for DPOF 1.1 compatible printers.
● Setting the Print Size
1. Select the [Size] menu by pressing the UP / DOWN
button and press the RIGHT button.
2. Select a desired sub menu by pressing the
UP / DOWN button and press the OK button.
[Select] : Selection window for an image to be
changed printed size is displayed.
- Up / Down / Left / Right : Select an image.
- Zoom W / T Button : Change the print size.
- OK button : Your changes will be saved and the
menu will disappear.
[All Pics] : Change print size of all saved images.
- W / T button : Select a print size
- OK button : Confirm the changed setting.
[Cancel] : Cancel all of the print size settings.
※ DPOF [Size] secondary menu : Cancel, 3X5, 4X6,
5X7, 8X10
※ Depending on the manufacturer and printer model,
cancelling the printing may take a little longer for
the printer to process.
DPOF
Standard
Index
Size
Select
All Pics
Cancel
Back:
W
W
Set:OK
Cancel
Set:OK
Cancel
■ You can use the USB cable to connect this camera to a printer that supports
PictBridge (sold separately) and print the stored images directly.
Movie clips and voice files cannot be printed.
■ Setting up the camera for connection with the printer
1. In any mode with the exception of Voice Recording
mode, press the MENU button.
2. Press the LEFT / RIGHT button and select
[SETUP] menu tab.
3. Select [USB] menu by pressing the UP / DOWN
button and press the RIGHT button.
4. Select [Printer] menu by pressing the UP / DOWN
button and press the OK button.
SETUP
AF Lamp
Sound
USB
LCD
Video Out
Back:
Computer
Printer
Set:OK
T
T
Set:OK
※ If you selected [COMPUTER] in Step 5, when you connect the camera to your
printer, the [USB ERROR!] message will display and the connection will not be
established. In this case, disconnect the USB cable, and then follow the
procedure from Step 2 onwards.
《49》
PictBridge : Picture Selection
● Setting the Number of Copies to Print
- Select [One Pic] or [All Pics]. A screen where you can set the number of copies
to print will appear as shown below.
■ If you select [Computer] sub menu in the [USB]
setup menu, [Connecting Computer] message will
display when you connect the camera to your
printer and the connection will not be established.
In this case, press the Printer button. [Connecting
Printer] message will display and the Easy printing
mode will be selected.
W◀
W◀
* In some instances the camera may not connect to the printer, this will depend on
the manufacturer of the printer.
■ Easy printing
When you connect the camera to printer in the Play
back mode, you can print a picture easily.
- Pressing the Printer (
) button :
The currently displayed image will be printed with
the printer’s default setting.
- Pressing the Left / Right button :
Selects a previous / next image.
◀
▶
Print:
Menu:Ok
0 Prints
▶T
▶T
Exit:Shutter
[When [One Pic] is selected]
141-0001
■ Select pictures to print
1. Press the Menu button.
IMAGES
2. The [Images] menu will appear.
One Pic
3. Use the UP and DOWN buttons to select the desired
All Pics
submenu value, and then press the OK button.
When [One Pic] is selected :
Move:
The PictBridge function will be applied only to the
picture currently displayed.
When [All Pics] is selected :
The PictBridge function will be applied to all pictures, excluding movie clips
and voice files.
《50》
Set:OK
0 Prints
Exit:Shutter
Set:OK
[When [All Pics] is selected]
- Press the Up / Down button to select the number of prints.
- When [One Pic] is selected : Use the Left / Right button to select another
picture. After selecting another picture, select the
number of prints for another picture.
- After setting the number of prints, press the OK button to save.
- Press the Shutter button to return to the menu without setting the number
of prints.
PictBridge : Print Setting
■ AUTO SET
1. Use the LEFT and RIGHT buttons to select the
[AUTO SET] menu tab.
2. Use the UP and DOWN buttons to select the
desired submenu value, and then press the OK
button.
[No] : [CUSTOM SET] values are kept.
[Yes] : All values in the [CUSTOM SET] are
automatically changed.
AUTO SET
No
Yes
Move:
PictBridge : Print Setting
PictBridge : Print
■ Custom Set : You can select the Paper Size, Print Format, Paper Type, Print
Quality, Date Print, and File Name Print menus for printed pictures.
1. Use the LEFT and RIGHT buttons to select the
[CUSTOM SET] menu tab.
2. Use the UP and DOWN buttons to select the
desired submenu value, and then press the
RIGHT button.
3. Use the UP and DOWN buttons to select the
desired submenu value, and then press the OK
button.
■ The menus you can set up are as follows:
Menu
Function
Size
Set the size of the printing paper
Layout
Type
Quality
Date
CUSTOM SET
Size
Layout
Type
Quality
Date
Move:
Auto
Auto
Auto
Auto
Auto
Sub menu
Auto, PostCard, Card, 4X6, L, 2L,
Letter, A4, A3
Set the number of pictures to be
Auto, Full, 1, 2, 4, 8, 9, 16, Index
printed on a sheet of paper
Set the quality of the printing
paper
Auto, Plain, Photo, FastPhoto
Set the quality of the picture to
be printed
Auto, Draft, Normal, Fine
Set whether to print the date
Auto, Off, On
File Name Set whether to print the file name Auto, Off, On
※ Some menu options are not supported on all printers.
If not supported, the menus are still displayed in the LCD, but are not selectable.
※ If the setting values are not changed in the automatic/ manual setting, the setting
values are automatically kept.
■ Printing Pictures
1. Use the LEFT and RIGHT buttons to select the [PRINT] menu tab.
2. Use the UP and DOWN buttons to select the desired submenu value, and
then press the OK button.
[Standard] : Print the pictures stored in the memory
PRINT
card in set numbers. One picture is
Standard
Index
printed on one piece of paper.
[Index]
: Print multiple images on one sheet of
paper.
Move:
3. The screen shown on the right will appear and the
picture will be printed. If no picture is selected, the
[No image!] message will be displayed.
Press the Menu / OK button while printing to cancel
the printing and the [Images] menu is displayed.
Now Printing
0001 / 0001
Exit:Shutter
※ Number of pictures on an index print varies
depends on the printer used.
■ DPOF Print : This allows you to directly print the files with DPOF information.
1. Use the LEFT and RIGHT buttons to select the
[DPOF PRINT] menu tab.
No
Yes
2. Use the UP and DOWN buttons to select the
desired submenu value, and then press the OK
button.
Move:
[No] : Cancel the printing
[Yes] : Directly print the file with the DPOF information
DPOF PRINT
※ Depending on the manufacturer and printer model, some menus may not be
available. When a printer does not support the DPOF, the menu is still
displayed but not available.
《51》
PictBridge : RESET
Setup menu
■ Initialises user-changed configurations.
1. Use the LEFT and RIGHT buttons to select the
[RESET] menu tab.
2. Use the UP and DOWN buttons to select the desired
submenu value, and then press the OK button.
If [No] is selected : Settings will not be reset.
If [Yes] is selected : All print and image settings
will be reset.
RESET
No
Yes
Move:
※ Default print setting varies depending on the printer manufacturer. For your
printer’s default setting, refer to the user’s guide that came with your printer.
■ In this mode, you can set up basic settings. You can use the setup menu in all
camera modes, except Voice Recording mode.
The items indicated by
are default settings.
Menu tab
Main menu
File
Power Off
Sub menu
Series
Reset
Off, 1, 3, 5,10min
Secondary menu
-
ENGLISH
DEUTSCH
Page
p.53
p.54
FRANÇAIS
ESPAÑOL
ITALIANO
P”CCK»…
Language
PORTUGUÊS
DUTCH
SVENSKA
SUOMI
DANSK
p.54
BAHASA
POLSKI
Format
Date&Time
World Time
Imprint
AF lamp
《52》
Magyar
No
Yes
07/02/01 13:00
yy/mm/dd
mm/dd/yy
dd/mm/yy
Off
Guam
Sydney
Off
Date
Date&Time
Off
On
-
p.54
p.55
p.55
p.55
p.55
Setup menu
Menu tab
Main menu
Sound
USB
LCD
Video Out
Quick View
Reset
File name
Sub menu
Off
Low
Medium
High
Secondary menu
Computer
-
Printer
-
-
p.55
-
Dark
-
Normal
-
Bright
-
NTSC
-
PAL
-
Off, 0.5, 1, 3 sec
-
No
-
Yes
-
※ Menus are subject to change without prior notice.
Page
-
p.55
■ This function allows the user to select the file naming format.
[Series] : New files are named using numbers that
follow the previous sequence, even when
a new memory card is used, or after
File
Power Off
formatting, or after deleting all pictures.
Language
Format
[Reset] : After using the reset function, the next file
Date&Time
Back:
name will be set from 0001 even after
formatting, deleting all or inserting a new
memory card.
SETUP
Series
Reset
Set:OK
p56
INFORMATION
p.56
p.56
p.56
● The first stored folder name is 100SSCAM, and the first file name is
SL270001
● File names are assigned sequentially from SL270001 → SL270002 → ~ →
SL279999.
● The folder number is assigned sequentially from 100 to 999 as follows:
100SSCAM → 101SSCAM → ~ → 999SSCAM.
● The files used with the memory card conform to the DCF (Design rule for
Camera File systems) format. If you change the image file name, the image
may not play back.
《53》
Auto power off
Format
■ This function switches the camera off after a specified period in order to prevent
unnecessary battery drainage.
[Off]
: The power off function will not
operate.
[1, 3, 5, 10 min] : The power will turn off
automatically if not used for the
period of time specified.
SETUP
File
Power Off
Language
Format
Date&Time
Off
1 min
3 min
5 min
10 min
Back:
Set:OK
INFORMATION
● After replacing the battery, the power off setting will be preserved.
● Note that the automatic power off function will not operate if the camera is in
connecting the computer or printer, slide show, playing back a voice
recording, playing back a movie clip and taking a composite shot.
■ This is used for formatting the memory. If you run [Format] on the memory, all
images, including the protected images, will be deleted. Be sure to download
important images to your PC before formatting the memory.
If [No] is selected : The memory card will not be
SETUP
formatted. Press the menu
Power Off
button twice and the menu
Language
No
Format
Yes
display will disappear.
Date&Time
World Time
If [Yes] is selected : A [Processing!] message
Back:
appears and the memory card
will be formatted. If you ran
FORMAT in Play mode, a [No Image!] message will
appear.
Set:OK
INFORMATION
Language
■ There is a choice of languages that can be displayed on the LCD monitor. Even
if the battery and AC charger are removed and inserted again, the language
setting will be preserved.
LANGUAGE sub menu :
English, Korean, French, German, Spanish, Italian,
S.Chinese, T.Chinese, Russian, Portuguese, Dutch,
Danish, Swedish, Finnish, Thai, BAHASA (MALAY/
INDONESIAN), Arabic, Czech, Polish, Hungarian
and Turkish.
《54》
SETUP
File
Power Off
Language
Format
Date&Time
Back:
ENGLISH
한국어
FRANÇAIS
DEUTSCH
ESPAÑOL
Set:OK
● Be sure to run [Format] on the following types of memory card.
- A new memory card or an unformatted memory card.
- A memory card that has a file this camera can't recognise or one that has
been taken from another camera.
● Always format the memory card using this camera. If you insert a memory
card that has been formatted using other cameras, memory card readers, or
PCs, you will get a [Card Error!] message.
Setting up the Date / Time / Date type
■ You can change the date and time that will be displayed on the captured images
and set up the date type.
RIGHT button : Selects the year / month / day / hour /
minute date type.
LEFT button : Moves the cursor to the [Date&Time]
main menu if the cursor is at the first
item of the date and time setup. In all
other cases, the cursor will be shifted
to the left of its current position.
UP and DOWN buttons : Changes the setting value.
SETUP
Language
Format
Date&Time
World Time
Imprint
▲
07/02/01
▼
13:00
yy/mm/dd
Back:
Set:OK
■ This menu enables you to display the local date and time on the LCD monitor.
SETUP
Back:
■ You can turn the Auto Focus lamp on or off.
If [Off] is selected : The AF lamp will not light up.
If [On] is selected : The AF lamp will light up.
SETUP
World Time
Imprint
AF Lamp
Sound
USB
Off
On
※ If you select [Off] menu and take an image in poorly
lit conditions or select the [Night] scene mode, the
Back:
camera may not be able to focus accurately.
※ The Auto Focus lamp will function while using the self-timer even if the
configuration is set to off.
Set:OK
Sound
World Time
Format
Date&Time
World Time
Imprint
AF Lamp
Auto Focus lamp
SETUP
Guam
Sydney
Set:OK
■ If you set the operation sound to on, various sounds
will be activated for camera start-up and when
buttons are pressed, so that you are aware of the
camera's operation status.
Guam, Sydney
07/02/01 15:08
Set:OK
Back:
Off
Low
Medium
High
Set:OK
Connecting an External Device (USB)
Imprinting the recording date
■ You can select an external device to which you want to connect the camera
using the USB cable.
■ There is an option to include DATE / TIME on still images.
: The DATE & TIME will not be
imprinted on the image file.
[Date]
: Only the DATE will be imprinted on the image file.
[Date&Time] : The DATE & TIME will be imprinted on the image file.
SETUP
Imprint
AF Lamp
Sound
USB
LCD
[Off]
SETUP
Date&Time
World Time
Imprint
AF Lamp
Sound
Off
Date
Date&Time
※ The Date & Time are imprinted at the bottom right
Back:
Set:OK
side of the still image.
※ The imprint function is applied only to still images except for the images taken in
the [Text] scene mode and photo frame effect mode.
[Computer] : Select this if you want to connect the
SETUP
camera to your PC. Refer to page 66
AF Lamp
Sound
Computer
for instructions on how to connect the
USB
Printer
LCD
camera to your PC.
Video Out
[Printer]
: Select this if you want to connect the
Back:
Set:OK
camera to your printer. Refer to page
49 for instructions on how to connect the camera to your printer.
《55》
LCD brightness
Selecting Video out type
■ You can adjust the LCD brightness.
INFORMATION
SETUP
SOund
USB
LCD
Video Out
Quick View
Dark
Normal
Bright
Back:
Set:OK
● When using a TV as an external monitor, you will need to select the external
or AV channel of the TV.
● There will be a digital noise on the external monitor, but it is not a malfunction.
● If the image is not in the centre of the screen, use the TV controls to centre it.
● The menu functions are the same as those indicated on the LCD monitor.
Selecting Video out type
■ The Movie output signal from the camera can be
NTSC or PAL. Your choice of output will be
governed by the type of device (monitor or TV, etc.)
to which the camera is connected. PAL mode can
support only BDGHI.
Quick view
SETUP
USB
LCD
Video Out
Quick View
Reset
Back:
NTSC
PAL
Set:OK
■ If you enable Quick View before capturing an image, you can view the image
you just captured on the LCD monitor for the duration set in the [Quick View]
setup. Quick view is possible only with still images.
[Off]
: The quick view function can’t be
activated.
[0.5, 1, 3sec] : The captured image is briefly
displayed during the selected time.
SETUP
USB
LCD
Video Out
Quick View
Reset
off
0.5 sec
1 sec
3 sec
Back:
Yellow - Video
White - sound
Set:OK
Initialisation
■ All camera menu and function settings will be restored to their default values.
However, values for DATE / TIME, LANGUAGE, and VIDEO OUT will not be
changed.
INFORMATION
● NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico.
● PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany,
U.K., Holland, Italy, Kuwait, Malaysia, New Zealand, Singapore,
Spain, Sweden, Switzerland, Thailand, Norway.
《56》
If [No] is selected : Settings will not be restored to
their defaults.
If [Yes] is selected : All settings will be restored to
their defaults.
SETUP
USB
LCD
Video Out
Quick View
Reset
Back:
No
Yes
Set:OK
Setting up the Mycam menu
Start up sound
■ YYou can set up a start up image, start up sound and shutter sound.
Every working mode of camera with the exception of Voice recording mode has
the MyCAM menu.
The items indicated by
are default settings.
Menu tab
Main menu
Start Image
Start Sound
Shutter Sound
Sub menu
Off
User Image 1
Off
Sound 2
Off
Sound 2
■ You can select the sound that is activated
whenever the camera is turned on.
p.57
p.57
Off
Sound 1
Sound 2
Sound 3
Back:
Page
LOGO
User Image 2
Sound 1
Sound 3
Sound 1
Sound 3
MYCAM
Start Image
Start Sound
Shutter Sound
Set:OK
INFORMATION
● If the start up image is set to [Off], the start up sound will not activate, even
though you may have set these to on.
p.57
※ Menus are subject to change without prior notice.
Shutter sound
Start up image
■ You can select the image that is first displayed on the
LCD monitor whenever the camera is turned on.
■ You can select the shutter sound.
MYCAM
MYCAM
Start Image
Start Sound
Shutter Sound
Start Image
Start Sound
Shutter Sound
Off
Back:
Back:
Off
Sound 1
Sound 2
Sound 3
Set:OK
Set:OK
INFORMATION
● Use a saved image for the start-up image with the [User Image] in the
[RESIZE] menu in the play mode.
● The start-up image will not be deleted by deleting all images or [Format] menu.
● The User images will be deleted by [Reset] menu.
《57》
Important notes
Be sure to observe the following precautions!
■ This unit contains precision electronic components. Do not use or store this unit
in the following locations.
- Areas exposed to severe changes in temperature and humidity.
- Areas exposed to dust and dirt.
- Areas exposed to direct sunlight or the inside of a vehicle in hot weather.
- Environments where there is high magnetism or excessive vibration.
- Areas with high explosives or highly flammable materials.
■ Do not leave this camera in places subject to dust, chemicals (like naphthalene
and mothball), high temperature and high humidity.
Keep this camera with silica gel in a hermetically sealed box when not planning
to use the camera for a long period of time
■ Sand can be particularly troublesome to cameras.
- Do not let sand get inside the camera when using it on beaches, coastal
dunes, or other areas where there is lots of sand.
- Doing so may result in failure or may permanently render the camera unusable.
■ Handling the camera
- Never drop the camera or subject it to severe shocks or vibrations.
- Protect the large size LCD monitor from an impact.
When this camera is not being used, keep it in the camera case.
- Avoid obstructing the lens or the flash when you capture an image.
- This camera is not waterproof.
To avoid dangerous electrical shocks, never hold or operate the camera with
wet hands.
- If you use this camera in wet places, such as beach or pool, do not let water or
sand get inside the camera. Doing so may result in failure or may permanently
damage the unit.
《58》
■ Extremes in temperature may cause problems.
- If the camera is transferred from a cold to a warm and humid environment,
condensation can form on the delicate electronic circuitry. If this occurs, turn the
camera off and wait for at least 1 hour until all moisture is dispersed. Moisture built
up can also occur in the memory card. If this happens, turn off the camera and
remove the memory card. Wait until the moisture has dispersed.
■ Caution on Using the Lens
- If the lens is subjected to direct sunlight, it could result in discoloration and
deterioration of the image sensor.
- Pay attention not to get fingerprints or foreign substances on the surface of the
lens.
■ If the digital camera is not used for a long period, an electric discharge can occur.
It is a good idea to remove the battery and the memory card if you do not intend
to use the camera for an extended period of time.
■ If the camera is exposed to an electronic interference, it will turn itself off to
protect the memory card.
■ Camera Maintenance
- Use a soft brush (available from photo stores) to gently clean the lens and LCD
assemblies.
If this does not work, lens-cleaning paper with lens cleaning fluid can be used.
Clean the camera body with a soft cloth. Do not allow this camera to come into
contact with solvent materials such as benzol, insecticide, thinners etc.
This may damage the body shell of the camera and also affect its performance.
Rough handling can damage the LCD monitor. Take care to avoid damage
and keep the camera in its protective carry case at all times when not in use.
■ Do not attempt to disassemble or modify the camera.
Important notes
■ Under certain conditions, static electricity can cause the flash unit to fire. This is
not harmful to the camera and is not a malfunction.
■ When images are uploaded or downloaded (when the charger and USB cable
are inserted into the cradle (optional) at the same time), the data transfer may be
affected by static electricity.
In this case, disconnect and re-connect the USB cable before trying the transfer
again.
■ Before an important event or going on a trip, you should check the camera
condition.
- Take a picture to test the camera's condition, and prepare spare batteries.
- Samsung cannot be held responsible for camera malfunctions.
Warning indicator
■ There are several warnings that may appear on the LCD display
Card Error!
•Memory card error
→ Turn off the camera power and turn it on again
→ Insert the memory card again
→ Insert the memory card and format the memory card. (p.54)
Memory Full!
•There is insufficient memory capacity to take an image
→ Insert a new memory card
→ Delete unnecessary image files to free up some memory
No Image!
•There are no images stored on the memory
→ Take images
→ Insert a memory card that is holding some images
File Error!
•File error
→ Format the memory card
•Memory card error
→ Contact a camera service centre
Low Battery!
•There is low battery capacity
→ Insert fresh batteries.
Low Light!
•When taking pictures in dark places
→ Take pictures in Flash Photography mode.
Out Of Number
•When selecting too many printing pages in the PictBridge menu.
→ Select printing page within the limitation.
Card Locked!
•The memory card is locked
→ SD memory card : Slide the write protect switch to the top of the memory card
《59》
Before contacting a service centre
■ Please check the following
The camera doesn’t switch on
•There is low battery capacity
→ Insert fresh batteries. (p.10)
•The battery may be inserted incorrectly.
→ Insert the battery according to the polarity marks (+, -)
•The battery is not inserted
→ Insert the battery and turn on the camera
The camera power ceases while in use
•The battery are exhausted
→ Insert charged battery
•The Camera is turned off automatically
→ Turn on the camera power again.
Battery power quickly drains
•The Camera is being used in low temperatures
→ Keep the camera in warm conditions (i.e. inside a coat or jacket) and only
remove it in order to take images
Camera does not take images when pressing the Shutter button
•There is insufficient memory capacity
→ Delete unnecessary image files
•The memory card has not been formatted
→ Format the memory card (p.54)
•The memory card is exhausted
→ Insert a new memory card
•The memory card is locked
→ Refer to [Card Locked!] error message
•The camera’s power is off
→ Turn the camera power on
《60》
•The battery is exhausted
→ Insert fresh batteries.
•Battery is inserted incorrectly with the polarities reversed
→ Insert the battery according to the polarity marks (+, -)
The camera suddenly stops working while in use
•The camera stopped due to a malfunction
→ Remove /re-insert battery and switch the camera on
The images are unclear
•A picture was taken without setting an appropriate macro mode
→ Select an appropriate macro mode to take a clear image.
•The picture was taken with the subject beyond the flash range
→ Take a picture within the flash range
•The lens is smudged or dirty
→ Clean the lens
The flash does not fire
•Flash off mode has been selected
→ Dis-engage flash off mode
•The camera mode can’t use the flash
→ Refer to the FLASH instruction (p.22~24)
Incorrect date and time is displayed
•The date and time have been set incorrectly or the camera has adopted the
default settings
→ Reset the date and time correctly
The camera buttons do not operate
•Camera malfunction
→ Remove / re-insert battery and switch the camera on
A card error has occurred while the memory card is in the camera.
•Incorrect memory card format
→ Re-format the memory card
Before contacting a service centre
The images don't play back
•Incorrect file name (Violation of DCF format)
→ Do not change the image file name
Colour of image is different to the original scene
•White balance or effect setting is incorrect
→ Select appropriate White balance and effect
Images are too bright
•Exposure is excessive
→ Reset exposure compensation
No image on external monitor
•The external monitor has not been connected properly with the camera
→ Check the connection cables
•There are incorrect files in the memory card
→ Insert a memory card that has correct files
When using the PC’s explorer, the [Removable Disk] file does not show
•Cable connection is incorrect
→ Check the connection
•The camera is off
→ Turn the camera on
•The operating system is not Windows 98, 98SE, 2000, ME, XP/ Mac OS 10.0 ~
10.3. Alternatively the PC does not support USB.
→ Install Windows 98, 98SE, 2000, ME, XP/ Mac OS 10.0 ~ 10.3 to PC that
supports USB.
•The camera driver is not installed
→ Install a [USB Storage Driver]
Specifications
■ Image Sensor
- Type : 1/2.5" CCD
- Effective Pixel : Approx. 7.2Mega-pixel
- Total Pixel : Approx. 7.4 Mega-pixel
■ Lens
- Focal Length : NV Lens f = 5.8 ~ 17.4mm (35mm equivalent : 35 ~ 105mm)
- F No. : F2.8 ~ F4.9
- Digital Zoom :ㆍStill Image mode : 1.0X ~ 5.0X
ㆍPlay mode : 1.0X ~ 10.0X (depends on image size)
■ LCD Monitor : 2.5" color TFT LCD (230,000 pixel)
■ Focusing
- Type : TTL contrast auto focus
- Range
Normal
Wide
Tele
80cm ~ infinity
Macro
5~80cm
40~80cm
Auto Macro
5cm~infinity
40cm~infinity
■ Shutter
- Speed : 1 ~ 1/2,000 sec. (Night Mode : 15 ~ 1/2,000 sec.)
■ Exposure
- Control : Program AE
Metering : Multi, Spot
- Compensation : ±2EV (0.5 EV steps)
- ISO Equivalent : Auto, 50, 100, 200, 400, 800, 1600
■ Flash
- Modes : Auto, Auto & Red-eye reduction, Fill-in flash, Slow sync, Flash off
- Range : Wide : 0.4 ~ 3.0m, Tele : 0.5 ~ 2.5m (ISO AUTO)
- Recharging Time : Approx. 4.0sec
■ Sharpness : Soft, Normal, Vivid
■ Effect : Color, B&W, Sepia, Red, Green, Blue, Negative, RGB, Highlight
■ White Balance : Auto, Daylight, Cloudy, Fluorescent_H, Fluorescent_L,
Tungsten, Custom
《61》
Specifications
■ White Balance : Auto, Daylight, Cloudy, Fluorescent_H, Fluorescent_L,
Tungsten, Custom
■ Voice Recording : Voice Recording (Max. 1 hour)
Voice Memo in Still Image (Max. 10 sec.)
■ Date Imprinting : Date&Time, Date, Off (user selectable)
■ Shooting
- Still Image : ㆍModes : Auto, Program, Scene, Voice Recording
※ 11 Scene (Night, Portrait, Children, Landscape, Close-up,
Sunset, Dawn, Backlight, Firework, Beach & Snow, Text)
ㆍShooting : Single, Continuous, AEB
ㆍSelf-timer : 10 sec., 2 sec., Double self timer (10sec. & 2sec.)
- Movie Clip :ㆍWith Audio or without Audio
(user selectable, recording time : memory capacity dependent)
ㆍSize : 640x480, 320x240
(3X Optical Zoom (Mute during Zoom Operation))
ㆍFrame rate : 30 fps, 15 fps
ㆍMovie Stabiliser (User Selectable)
ㆍMovie Editing (Embedded) : Pause during recording, Still Image
Capture, Time Trimming
■ Storage
- Media : Internal memory : Approx. 20MB flash memory
External memory : SD card / MMC/ SDHC (Up to 4GM Guaranteed)
- File Format : Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.0
Movie Clip : AVI (MPEG-4)
Audio : WAV
- Image Size
7M
5M
3M
1M
3072x2304
2592x1944
2048x1536
1024x768
- Capacity (256MB MMC)
Superfine
7M
5M
3M
1M
76
93
173
560
Fine
113
159
266
673
Normal
193
272
425
743
※ These figures are measured under Samsung’s standard conditions and may
vary depending on shooting conditions and camera settings.
■ Image Play
- Type : Single image, Thumbnails, Slide show, Movie Clip
- Editing : Trimming, Rotating, Resizing, Colour Effect
■ Interface : Digital output connector : USB 2.0 (Mass Storage Class)
Video Out : Pal & NTSC selectable
Audio : Mono (without external codec)
Pictbridge (Full Option)
■ Power Source : Rechargeable battery : 3.7V Li-ion battery (SLB-0837)
※ Included battery may vary depending on sales region.
■ Dimensions (WxHxD) : 96.9 X 56.8 X 20.5 mm
■ Weight : 130g
- Operating Temperature : 0 ~ 40°C
- Operating Humidity : 5 ~ 85%
■ Software
- Application : Digimax Master, Adobe Reader
■ Special Features
- 3X Optical Zoom for Still & Movie.
MPEG-4 VGA 30 fps Movie Clip (supporting Edit on DSC), Effect Key
Powerful Effect (Colour, Highlight), Easy Mode Change using “M” button
※ Specifications are subject to change without prior notice.
※ All trademarks are the property of their respective owners.
《62》
Software Notes
About the software
Please ensure that you read the instruction manual carefully before use.
•The attached software is a camera driver and image editing software tool for
Windows.
•Under no circumstances should all or part of either the software or the user
manual be reproduced.
•Copyrights for software are licensed only for use with a camera.
•In the unlikely event of a manufacturing fault, we will repair or exchange your
camera.
We cannot, however, be held responsible in any way for damage caused by
inappropriate use.
•Using a Hand-made PC or a PC and OS that has not been guaranteed by the
manufacturer is not covered by the Samsung warranty.
•Before reading this manual, you should have a basic knowledge of computers
and O/S (Operating Systems).
System Requirements
For Windows
PC with processor better than Pentium II 450MHz
(Pentium 700MHz recommended)
Windows 98 / 98SE / 2000 / ME / XP
For Macintosh
Power Mac G3 or later
Mac OS 10.0 ~ 10.3
After inserting the CD-ROM provided with this camera into the CD-ROM drive, the
following window should automatically run.
Before connecting the camera to the PC, you
should first install the camera driver.
※Screen Captures illustrated on this manual is
based on English Edition of Windows.
■ Camera driver : This enables images to transfer between the camera
and PC.
This camera uses the USB Storage Driver as the camera driver. You can use
the camera as a USB card reader. After installing the driver and connecting this
camera to the PC, you can find [Removable Disk] in [Windows Explorer] or [My
Computer]. A USB Storage Driver is provided only for Windows. A USB Driver
for MAC is not included with the Application CD. You can use the camera with
Mac OS 10.0 ~ 10.3.
■ Digimax Master : This is the all-in-one multi media software solution.
You can download, view, edit and save your digital images and movie clips clip
with this software. This software is only compatible with Windows.
Minimum 64MB RAM (Over 128MB recommended) Minimum 64MB RAM
200MB of available hard-disk space (Over 1GB recommend) 110MB of available hard-disk space
USB port
USB port
CD-ROM drive
CD-ROM drive
1024x768 pixels, 16bit colour display
compatible monitor
(24bit colour display recommended)
MPlayer
DivX (For movie clip)
INFORMATION
● Be sure to check the system requirements before installing the driver.
● You should allow 5 ~ 10 seconds for running the automatic setup program
according to the capability of your computer. If the frame does not show, run
the [Windows Explorer] and select [Installer.exe] in the CD-ROM Drive root
directory.
《63》
Setting up the application software
■ To use this camera with a PC, install the application software first.
After this has been done, the stored images in the camera can be moved to the
PC and can be edited by an image editing program.
■ You can visit the Samsung web-site through the internet.
http://www.samsungcamera.com : English
http://www.samsungcamera.co.kr : Korean
1. The auto run frame will display.
Click the [Install] menu in the Auto
run frame.
2. Install the camera driver, DirectX, Xvid and Digimax Master by selecting a
button shown on the monitor. If an upper version of DirectX was installed on
your computer, DirectX may not be installed.
※ The XviD codec is distributed according to and under the terms and conditions of
the GNU General Public License and everyone can copy, modifiy and distribute
this codec freely, but WITHOUT ANY WARRANTY, IMPLIED OR
EXPRESSED, OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE; provided, however, that you have to follow the GNU General Public
License whenever you are distributing this codec or modification thereof.
For more information see the GNU General Publice License documents
(http://www.gnu.org/copyleft/gpl.html).
《64》
Setting up the application software
3. After restarting the computer, connect the PC to the camera with the USB
cable.
4. Turn the camera power on.
The [Found New Hardware Wizard] will
open and the computer will recognise the
camera.
※ If your OS is Windows XP, an image
viewer program will open.
If the download window of Digmax
Master opens after starting Digimax
Master, the camera driver was set up
successfully.
INFORMATION
● If you have installed the camera driver, the [Found New Hardware Wizard]
may not open.
● On a Windows 98/98SE system, the Found New Hardware Wizard dialog
box opens and a window asking you to select a driver file may appear. In
this case, specify "USB Driver" in the CD supplied. (for Windows 98/98SE).
● PDF documents of user manual are included in the Software CD-ROM
supplied with this camera. Search the PDF files with Window's explorer.
Before opening the PDF files, you must install the Adobe Reader included in
the Software CD-ROM.
● To install the Adobe Reader 6.0.1 correctly, Internet Explorer 5.01 or later
had to be installed. Visit "www.microsoft.com" and upgrade the Internet
Explorer
《65》
Starting PC mode
•If you connect the USB cable to a USB port on your PC and then turn on the
power, the camera will automatically switch to "computer connection mode".
•In this mode, you can download stored images to your PC through the USB
cable.
•The LCD monitor is always turned off in PC mode.
■ Connecting the camera to a PC
1. In any mode with the exception of Voice
Recording mode, press the Menu button.
2. Press the LEFT / RIGHT button and select the
[SETUP] menu tab.
3. Select the [USB] menu by pressing the UP /
DOWN button and press the RIGHT button.
4. Use the UP and DOWN buttons to select
[Computer], and then press the OK button.
5. Press the menu button twice and the menu will
disappear.
6. Connect the PC to the camera with the USB
cable.
■ Connecting the camera to a PC
SETUP
AF Lamp
Sound
USB
LCD
Video Out
Back:
Computer
Printer
Set:OK
※ If you selected [Printer] in Step 4, when you connect the camera to your
printer, the [Connecting Printer] message will display and the connection will
not be established.
In this case, disconnect the USB cable, and then follow the procedure from
Step 2 and onward.
■ Disconnecting the camera and PC : Refer to page 68
(Removing the removable disk).
INFORMATION
● To save battery power, it is recommended that you use the cradle (optional)
when connecting the camera to a computer.
《66》
Starting PC mode
■ Downloading stored images
You can download the still images stored on the camera to your PC's hard disk
and print them or use a photo editing software to edit them.
6. Press the right mouse button and a pop-up
menu will open. Click [Paste].
1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display, select
[My Computer] and double click [Removable
Disk → DCIM → 100SSCAM].
The image files will then be displayed.
7. An image file is transferred from the camera to
your PC.
3. Select an image and press the right
mouse button.
- By using [Digimax Master], you can see the stored images in the memory
directly on the PC monitor and you can copy or move the image files.
4. A pop-up menu will open.
Click the [Cut] or [Copy] menu.
- [Cut] : cuts a selected file.
- [Copy] : copies files.
CAUTION
● We recommend that you should copy the images to the PC to view them.
Opening images directly from the removable disk may be subject to
unexpected disconnection.
● When you upload a file that is not taken by this camera to the Removable
Disk, the [File Error!] message will be displayed on the LCD monitor in the
PLAY mode, and nothing is displayed in THUMBNAIL mode.
5. Click a folder where you want to paste the file.
《67》
Removing the removable disk
■ Windows 98/98SE
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has finished
blinking and is constantly on.
2. Unplug the USB cable.
■ Windows 2000/ME/XP
(The illustrations may differ from those shown depending on the Windows O/S.)
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has finished
blinking and is constantly on.
2. Double-click the [Unplug or Eject Hardware] icon
on the task bar.
[Double-click!]
3. The [Unplug or Eject Hardware] window will
open. Select the [USB Mass Storage Device]
and click the [Stop] button.
4. The [Stop a Hardware device] window will open.
Select the [USB Mass Storage Device] and click
the [OK] button.
5. A [Safe to Remove Hardware] window will
open. Click the [OK] button.
《68》
6. A [Unplug or Eject Hardware] window will open.
Click the [Close] button and the removable disk
will be removed safely.
7. Unplug the USB cable.
Setting up the USB Driver for MAC
1. A USB Driver for MAC is not included with the software CD as MAC OS
supports the camera driver.
2. Check the MAC OS version during start-up.
This camera is compatible with MAC OS 10.0 ~ 10.3.
3. Connect the camera to the Macintosh and turn the camera power on.
4. A new icon will be displayed on the desktop after connecting the camera to
the MAC.
Using the USB Driver for MAC
1. Double click a new icon on the desktop and the folder in the memory will be
displayed.
2. Select an image file and copy or move it to MAC.
CAUTION
● For Mac OS 10.0 or later : First complete uploading from computer to
camera and then remove the removable disk
with the Extract command.
● If a movie clip can’t play back on the Mac OS, please visit the following site
(http://www.divx.com/divx/mac/) and download the codec.
Or, use a media player that supports the Xvid codec (Mplayer).
Removing the USB Driver for Windows 98SE
■ To remove the USB driver, refer to the process shown below.
1. Connect the camera to your PC and turn it on.
2. Check whether the Removable Disk is on the [My Computer].
3. Remove the [Samsung Digital Camera] on the Device manager.
Digimax Master
■ You can download, view, edit and save your images and movies with this software.
This software is only compatible with Windows except for the Windows 98.
■ To start the program, click [Start → Programs → Samsung → Digimax Master →
Digimax Master].
● Downloading images
1. Connect the camera to your PC.
4. Disconnect the USB cable.
5. Remove the [SAMSUNG USB DRIVE] on the Add / Remove Programs
Properties.
2. A window for downloading images will
display after connecting the camera to your
PC.
- To download the captured images, select
the [Select All] button.
- Select desired folder in the window and
click the [Select All] button. You can save
captured images and selected folder.
- If you click the [Cancel] button, downloading will be
cancelled.
3. Click [Next >] button.
6. Uninstallation is complete.
《69》
Digimax Master
4. Select a destination and make a folder to
save downloaded images and folders.
- Folder names can be made in order of date
and images will be downloaded.
- Folder name will be made as you want and
images will be downloaded.
- After selecting a folder that was made
before, images will be downloaded.
● Image viewer : You can view the stored images.
①
⑤
⑥
⑦
②
5. Click [Next >] button.
③
6. A window will open as shown alongside.
The destination of the selected folder will be
displayed on the upper side of the window.
Click the [Start] button to download the
images.
7. Downloaded images will be displayed.
④
- Image viewer functions are listed below.
① Menu bar : You can select menus.
File, Edit, View, Tools, Change functions, Auto download, help, etc.
② Image selection window : You can select the desired images in this window.
③ Media type selection menu : You can select image viewer, image edit and
movie edit functions in this menu.
④ Preview window : You can preview an image or a movie clip and check the
multi media information.
⑤ Zoom bar : You can change preview size.
⑥ Folder display window : You can see the folder location of the selected
image.
⑦ Image display window : Images of the selected folder are displayed.
※ Refer to the [Help] menu in Digimax Master for further information.
《70》
Digimax Master
● Image edit : You can edit the still image.
● Movie edit : You can get the still image, movie clip, narration, music files together
in a movie clip.
①
①
④
②
②
③
- Image edit functions are listed below.
① Edit menu : You can select the following menus.
[Tools]
: You can resize or crop the selected image. See the [Help] menu.
[Adjust] : You can modify image quality. See the [Help] menu.
[Retouch] : You can change image or insert effects on the image. See the
[Help] menu.
② Drawing tools : Tools for editing an image.
③ Image display window : A selected image displays in this window.
④ Preview window : You can preview the changed image.
※ A still image edited with Digimax Master can’t be played back on the camera.
※ Refer to the [Help] menu in Digimax Master for further information.
- Movie clip edit functions are listed below.
① Edit menu : You can select the following menus.
[Add Media] : You can add other media elements to a movie.
[Edit Clip] : You can change the brightness, contrast, colour and saturation.
[Effects]
: You can insert an effect.
[Set Text] : You can insert texts.
[Narrate]
: You can insert a narration.
[Produce] : You can save the edited multi media as a new file name.
You can select AVI, Windows media (wmv), Windows media
(asf) and movie clip for this camera (avi, MPEG-4) file types.
② Frame display window : You can insert multi media in this window.
※ Some movie clips that were compressed with a codec that is not compatible with
the Digimax Master can’t play back in the Digimax Master.
※ Refer to the [Help] menu in Digimax Master for further information.
《71》
Digimax Master
FAQ
■ Movies for viewing on the camera : You can play back a movie on this camera
1. Select a movie for playing back on the camera by pressing the [Add] button.
Insert effects and edit the movie. To save the edited movie, press the [Make] button.
2. Select [Movie for camera] video type.
3. Select Camera option, Output location, File name and press the [Make] button.
- Frame size : Selecting the width and height of the frame.
- Frame rate : Selecting the frame rate per second.
- File location : Selecting a location where the edited movie is saved.
- File name : To play back the movie on the camera, you must keep the DCF
rule. Save the movie as SL27XXXX.avi (You can input any
numbers between 0001 ~ 9999
instead of XXXX letters).
4. Connect the camera to the computer with the
included USB cable.
5. Copy the edited movie to [Removable
Disk\DCIM\XXXSSCAM].
(You can input any numbers between 100 ~ 999
instead of XXX letters)
6. You can play back the movie in the Play mode of
the camera.
Play: /
《72》
Capture:E
■ Please check the following if the USB connection malfunctions.
Case 1
USB cable is not connected or it is not the supplied USB cable.
→ Connect the supplied USB cable.
Case 2
The camera is not recognised by your PC.
Sometimes, the camera may appear under [Unknown Devices] in
Device Manager.
→ Install the camera driver correctly.
Turn off the camera, remove the USB cable, plug in the USB cable
again, and then turn on the camera.
Case 3
There is an unexpected error during file transfer.
→ Turn the camera power off and on again. Transfer the file again.
Case 4
When using the USB hub.
→ There may be a problem in connecting the camera to the PC through
the USB hub if the PC and the hub are not compatible. Wherever
possible, connect the camera to the PC directly.
Case 5
Are other USB cables connected to the PC?
→ The camera may malfunction when it is connected to the PC at the
same time as another USB cable. In this case, disconnect the other
USB cable, and connect only one USB cable to the camera.
FAQ
Case 6
When I open the Device Manager (by clicking Start → (Settings) →
Control Panel → (Performance and Maintenance) → System →
(Hardware) → Device Manager), there are Unknown Devices or Other
Devices entries with a yellow question mark(?) beside them or devices
with an exclamation mark(!) beside them.
→ Right-click on the entry with the question (?) or exclamation (!) mark
and select "Remove". Restart the PC and connect the camera again.
For Windows 98 PC, remove the camera driver also, restart the PC,
and then reinstall the camera driver.
Case 7
In some security programs (Norton Anti Virus, V3, etc.), the computer
may not recognise the camera as a removable disk.
→ Stop the security programs and connect the camera to the computer.
Refer to the security program instructions about how to temporarily
disable the program.
Case 8
The camera is connected to the USB port located on the front of the
computer.
→ When the camera is connected to the USB port located on the front of
the computer, the computer may not recognise the camera. Connect
the camera to the USB port located on the back of the computer.
■ When the movie clip doesn’t play back on the PC
※ When the movie clip recorded by the camera doesn’t play back on the PC,
the causes are mostly due to the codec installed on the PC.
● When codec for play back the movie clip isn’t installed
→ Install the codec as listed below.
[ Installing codec for Windows ]
1) Insert the CD provided with the camera.
2) Run the windows explorer and select [CD-ROM drive:\XviD] folder and
click the XviD-1.0.3-20122004.exe file.
※ The XviD codec is distributed according to the GNU General Public Licence
and everyone can copy, distribute and change this codec. This Licence
applies to any program or other work which contains a notice placed by the
copyright holder saying it may be distributed under the terms of this General
Public Licence.
For more information, see the Licence documents
(http://www.gnu.org/copyleft/gpl.html).
[ Installing codec for Mac OS ]
1) Visit the following site for downloading the codec.
(http://www.divx.com/divx/mac)
2) Click the [Free Download] button located at the upper right side of the page
and a window for downloading the DivX codec will display.
3) Select Mac OS you use and click the [Download] button. Save it on a folder
you want to.
4) Run the downloaded file and the codec for playing back the movie clip will
be installed.
※ If a movie clip can’t play back on the Mac OS, use a media player that
supports XviD codec (Mplayer).
《73》
FAQ
● When the DirectX 9.0 or later is not installed
→ Install the DirectX 9.0 or later
1) Insert the CD provided with the camera
2) Run the windows explorer and select the [CD-ROM drive:\ USB
Driver\DirectX 9.0] folder and click the DXESETUP.exe file.
The DirectX will be installed. Visit the following site for downloading the
DirectX.http://www.microsoft.com/directx
● If a PC (Windows 98) stops responding while the camera and PC are connected
repeatedly
→ If a PC (Windows 98) is turned on for a long time and the camera is
connected repeatedly, the PC may not recognise the camera. In this case, restart the PC.
Correct Disposal of This Product
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for
environmentally safe recycling. Business users should contact their supplier and
check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
● If a PC connected with the camera stops responding while Windows is starting.
→ In this case, disconnect the PC and the camera and Windows will start.
If the problem happens continuously, set the Legacy USB Support to disable
and re-start the PC. The Legacy USB Support is in the BIOS setup menu.
(The BIOS setup menu differs from the PC manufacturers and some BIOS
menus don’t have Legacy USB Support) If you can’t change the menu by
yourself, contact to the PC manufacturer or BIOS manufacturer.
● If the movie clip can’t be deleted, removable disk can’t be extracted or an error
message displays during the file transfer.
→ If you install only the Digimax Master, the problems mentioned above
occasionally happen.
- Close the Digimax Master program by clicking the Digimax Master icon on
the Taskbar.
- Install all the application programs included in the software CD.
(You must install the Movie clip codec)
《74》
Samsung Techwin cares for the environment at all product
manufacturing stages to preserve the environment, and is
taking a number of steps to provide customers with more
environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly
products, and indicates that the product satisfies the EU
RoHS Directive.
FCC notice
MEMO
■ NOTE :
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorientate, or relocate, the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
■ CAUTION :
Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the
equipment.
■ Declaration of Conformity
Trade Name
: SAMSUNG TECHWIN
Model No.
: Samsung L700
Responsible Party : Samsung Opto-Electronics America, INC.
Address
: 40 Seaview Dr. Secaucus,NJ 07094
Telephone No.
: 201-902-0347
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
《75》
MEMO
《76》
MEMO
SAMSUNG TECHWIN CO., LTD.
SAMSUNG OPTO-ELECTRONICS GmbH
OPTICS & DIGITAL IMAGING DIVISION
145-3, SANGDAEWON 1-DONG, JUNGWONGU,
SUNGNAM-CITY, KYUNGKI-DO, KOREA
462-121
TEL : (82) 31-740-8222, 8488, 8490
FAX : (82) 31-740-8398
www.samsungcamera.com
ZENTRALE, KEINE REPARATUR
AM KRONBERGER HANG 6
D-65824 SCHWALBACH/TS, GERMANY
TEL : 49 (0) 6196 66 5303
FAX : 49 (0) 6196 66 5366
TECHNISCHE SERVICE HOTLINE :
00800 4526 3727
(nur kostenfrei fur Anrufe aus Deutschland)
SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
1-800-SAMSUNG (726-7864)
www.samsungcamerausa.com
If you have any questions or comments relating to
Samsung cameras, Please contact
the SAMSUNG customer care center
Die Adressen Ihrer Kundendienste sowie die
Garantiebestimmungen entnehmen Sie bitte aus dem
beiliegenden Faltblatt (SAMSUNG INTERNATIONAL
WARRANTY CERTIFICATE)
INTERNET : www.samsungcameras.de
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD
SAMSUNG FRANCE S.A.S.
HOTLINE PHOTO NUMÉRIQUE :
00 800 22 26 37 27 (Numéro Vert-Appel Gratuit)
www.samsungphoto.fr
NO.9 ZHANGHENG STREET. MICRO-ELECTRONIC
INDUSTRIAL PARK JINGANG ROAD TIANJIN CHINA.
POST CODE : 300385
TEL : 800-810-5858
www.samsungcamera.com.cn
SAMSUNG OPTO-ELECTRONICS UK LIMITED
SAMSUNG HOUSE 1000 HILLSWOOD DRIVE
HILLSWOOD BUSINESS PARK
CHERTSEY KT16 OPS U.K.
TEL : 00800 12263727
(free for calls from UK only)
UK Service Hotline : 01932455320
www.samsungcamera.co.uk
RUSSIA INFORMATION CENTER
SAMSUNG ELECTRONICS
117545 ST. DOROZHNAYA BUILDING 3,
KORPUS 6, ENTRANCE 2, MOSCOW, RUSSIA
TEL : (7) 495-363-1700
CALL FREE : (8) 800 555 55 55 (from Russia only)
www.samsungcamera.ru
Internet address - http : //www.samsungcamera.com
The CE Mark is a Directive conformity
mark of the European Community (EC)
6806-4307
Download PDF