Samsung | SAMSUNG L83T | Samsung L83T User Manual

Instructions
Getting to know your camera
Use this camera in the following order
Set up the camera driver
Take a picture
Before connecting the camera to a PC, via
the USB cable, you will need to set up the
camera driver. Install the camera driver
that is contained in Application software
CD-ROM. (p.100)
Take a picture. (p.19)
Thank you for buying a Samsung Digital Camera.
● Prior to using this camera, please read the user manual thoroughly.
● If you require After Sales service, please bring the camera and the cause of the
camera malfunction (such as battery, Memory card etc.) to the A/S centre.
● Please check that the camera is operating properly prior to when you intend to
use it (e.g. for a trip or an important event) to avoid disappointment. Samsung
camera takes no responsibility for any loss or damages that may result from
camera malfunction.
● Keep the manual in a safe place.
● The contents and illustrations of this manual are subject to change without prior
notice for upgrading the camera functions.
Insert the USB cable
Insert the supplied USB cable into the
PC’s USB port and the camera’s USB
connection terminal. (p.103)
Check the camera’s power
Check the camera’s power. If the power is
turned off, press the camera button to turn
it on.
Check [Removable Disk]
Open Windows EXPLORER and search
for [Removable Disk]. (p.103)
Microsoft, Windows and Windows logo are registered trademarks of Microsoft
Corporation incorporated in the United States and/or other countries.
All brand and product names appearing in this manual are registered trademarks
of their respective companies.
■ If you use a card reader to copy the images on the memory card to your PC, the
images could be damaged. When transferring the images taken with the camera
to your PC, be sure to use the supplied USB cable to connect the camera to your
PC. Please note that the manufacturer takes no responsibility for loss or damage
of images on the memory card due to the use of a card reader.
《1》
Danger
Warning
DANGER indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
● Do not attempt to modify this camera in any way. This may result in fire, injury,
electric shock or severe damage to you or your camera. Internal inspection,
maintenance and repairs should be carried out by your dealer or Samsung
Camera Service centre.
● Please do not use this product in close proximity to flammable or explosive
gases, as this could increase the risk of explosion.
● Should any form of liquid or a foreign object enter the camera, do not use it.
Switch off the camera, and then disconnect the power source. You must contact
your dealer or Samsung Camera Service centre. Do not continue to use the
camera as this may cause a fire or electric shock.
● Do not insert or drop metallic or inflammable foreign objects into the camera
through access points e.g. the memory card slot and battery chamber. This may
cause a fire or electric shock.
● Do not operate this camera with wet hands. This could pose a risk of electric
shock.
● Do not use the flash in close proximity to people or animals. Positioning the flash
too close to your subject’s eyes may cause eyesight damage.
● For safety reasons keep this product and accessories out of reach of children or
animals to prevent accidents e.g.:
- Swallowing battery or small camera accessories. If an accident should occur,
please consult a doctor immediately.
- There is the possibility of injury from the camera’s moving parts.
● Battery and camera may become hot during prolonged use and it may result in
camera malfunction. Should this be the case, allow the camera to sit idle for a
few minutes to allow it time to cool.
● Do not leave this camera in places subject to extremely high temperatures, such
as a sealed vehicle, direct sunlight or other places of extreme variances in
temperature. Exposure to extreme temperatures may adversely affect the
camera’s internal components and could cause a fire.
● When in use, do not cover the camera or Charger. This may cause heat to build
up and distort the camera body or cause a fire. Always use the camera and its
accessories in a well-ventilated area.
《2》
Caution
CAUTION indicates a potentially hazardous situation which, if not avoided,
may result in a minor or moderate injury.
● Leaking, overheating, or burst battery could result in fire or injury.
- Use battery with the correct specification for the camera.
- Do not short circuit, heat or dispose of battery in fire.
- Do not insert the battery with the polarities reversed.
● Remove the battery when not planning to use the camera for a long period of
time. Battery may leak corrosive electrolyte and permanently damage the
camera’s components.
● Do not fire the flash while it is in contact with hands or objects. Do not touch the
flash after using it continuously. It may cause burns.
● Do not move the camera while it is switched on when you are using the AC
Charger. After use, always switch off the camera before unplugging the cable
from the wall socket. Then make sure that any connector cords or cables to
other devices are disconnected before moving the camera. Failure to do so may
damage the cords or cables and cause a fire or electric shock.
● Take care not to touch the lens or lens cover to avoid taking an unclear image
and possibly causing camera malfunction.
● Avoid obstructing the lens or the flash when you capture an image.
● Credit cards may be demagnetized if left near case. Avoid leaving magnetic strip
cards near the case.
Contents
READY
007 System chart
008 Identification of features
008
Front & Top
009
Back
010
Bottom
010
5 Function button
012 Connecting to a Power Source
015 Inserting the memory card
016 Instructions on how to use the memory
card
RECORDING
018 LCD monitor indicator
019 Changing the recording mode
019 Starting the recording mode
019
How to use the Auto mode
020
How to use the Program mode
020
How to use the ASR mode
021
How to use the Movie clip mode
021
Recording the movie clip without sound
021
Pausing while recording a movie clip
(Successive Recording)
022
How to use the Scene modes
023 Things to Watch Out for When Taking
Pictures
《3》
Contents
024 Using the camera buttons to set the camera
045
Quality / Frame rate
024
POWER button
046
Metering
024
SHUTTER button
046
Drive mode
024
ZOOM W / T button
047
ISO
026
Face recognition(FR) button
048
White balance
027
Info / Up button
049
Exposure compensation
027
Macro / Down button
049
Long Time shutter
029
Focus lock
050
Movie Clip frame stabiliser
029
Flash / Left button
031
Self-timer / Right button
050 Using the LCD monitor to adjust the camera
settings
033
MENU / OK button
051
033
M (Mode) button
051
Contrast
034
E (Effect) button
051
Auto Focus type
035
E (Effect) button : Colour
052
Voice Memo
036
E (Effect) button : Colour Mask
052
Voice Recording
037
E (Effect) button : Saturation
053
Recording the movie clip without voice
E (Effect) button : FUN
053
SCENE mode
038
038
Cartoon
040
Pre-set focus frame
041
Composite shooting
043
Photo Frame
054 Sound menu
054 Sound
054
Volume
044
How to use the Fn menu
054
Start up sound
045
Size
054
Shutter sound
044
《4》
SETUP
Sharpness
Fn button
Contents
PLAY
055
Beep Sound
063
055
AF sound
063
Movie clip capture function
On camera movie trimming
055 Setup menu
064
Playing back a recorded voice
056 Setup menu 1
064
Playing back a voice memo
056
File name
065 LCD monitor Indicator
057
LANGUAGE
065 Using the camera buttons to set the camera
057
Setting up the Date / Time / Date type
065
Thumbnail / Enlargement button
057
World Time
067
Info / Up button
058
Imprinting the recording date
067
Play & Pause / Down button
058
LCD brightness
068
Left / Right / Menu / OK button
058
Auto Focus lamp
068
Printer button
058
Start up image
068
Delete button
059 Setup menu 2
069
E (Effect) button : Resize
059
Quick view
070
E (Effect) button : Rotating an image
059
Auto power off
070
E (Effect) button : Colour
059
LCD save
071
E (Effect) button : Special Colour
060
Selecting Video out type
071
Colour Filter
061
Formatting a memory
072
Colour mask
061
Initialisation
073
E (Effect) button : Image editing
073
Red eye Removal
073
Brightness control
062 Starting play mode
073
Contrast control
062
Playing back a still image
074
Saturation control
062
Playing back a movie clip
074
Noise Effect
《5》
Contents
075 E (Effect) button : FUN
091 Important notes
075
Cartoon
092 Warning indicator
076
Preset focus frames
093 Before contacting a service centre
077
Composite image
095 Specifications
079
Photo Frame
080
Sticker
080 Setting up the play back function using the
LCD monitor
098 Software Notes
098 System Requirements
082
Starting the slide show
082
Start the slide show
100 Setting up the application software
082
Selecting Images
102 Starting PC mode
083
Configure slide show effects
105 Removing the removable disk
083
Setting play interval
106 Setting up the USB Driver for MAC
083
Setting Background Music
106 Using the USB Driver for MAC
084
Playback
099 About the software
Voice memo
106 Removing the USB Driver for Windows
98SE
084
Deleting images
107 Samsung Master
085
Protecting images
110 FAQ
085
DPOF
084
087
088
《6》
SOFTWARE
Copy To Card
PictBridge
089
PictBridge : Picture Selection
090
PictBridge : Print Setting
090
PictBridge : Reset
System chart
Please check that you have the correct contents before using this product. The contents can vary depending on the sales region. To buy the optional equipment,
contact your nearest Samsung dealer or Samsung service centre.
< Included items >
Camera case
User manual,
Product warranty
DPOF compatible
printer (see p.85)
Camera strap
Software CD
(see p.99)
Computer
(see p.103)
PictBridge compatible
printer (see p.88)
SD/SDHC memory card / MMC
(see p.15)
AV cable
AC adapter (SAC-45) /
USB cable (SUC-C2)
Rechargeable battery
(SLB-0837B)
External monitor
(see p. 60)
《7》
Identification of features
Front & Top
Shutter button
Power button
FR (Face Recognition) button
Flash
AF sensor/Self-timer lamp
Speaker
Microphone
Lens
《8》
Identification of features
Back
Camera status lamp
Zoom T button (Digital zoom)
Zoom W button (Thumbnail)
M (Mode) button
LCD monitor
Eyelet for camera strap
E (Effect) button
5-function button
Fn/Delete button
Play mode/Print button
《9》
Identification of features
Bottom
5 Function button
Battery holder
Memory card slot
Information / Up button
MENU/OK button
Self-timer /
Right button
Flash /
Left button
Battery chamber
Battery chamber cover
USB/AV connection terminal
Tripod socket
※ To open the battery chamber cover, slide it in the direction shown above.
《10》
Macro / Down button
Play & Pause button
Identification of features
■ Self-timer lamp
Icon
Status
Blinking
Blinking
Blinking
Blinking
Description
- For the first 7 seconds, the lamp blinks at 1 second
intervals.
- For the final 3 seconds, the lamp blinks quickly at 0.25second intervals.
For the 2 seconds, the lamp blinks quickly at 0.25-second
intervals.
A picture will be taken after about 10 seconds and 2
seconds later a second picture will be taken.
After pressing the Shutter button, the image is taken in
accordance with the subject's movement.
■ Mode icon : Refer to page 19 for more information about the camera mode
setting.
MODE
Auto
Program
Movie
ASR
SHOOTING
Night
SCENE
Dawn
Portrait Children Landscape Close-up
Back
light
Fire
works
Beach
&Snow
Selfshot
Text
Sunset
Food
Cafe
■ Camera Status Lamp
Status
Description
The lamp turns on and off when the camera is
ready to take a picture
The lamp blinks while saving the image data and
After taking a picture
turns off when the camera is ready to take a picture
The lamp lights up
When the USB cable is
inserted to a PC
(LCD monitor turns off after initializing the device)
Transmitting Data with a PC The lamp blinks (LCD monitor turns off)
When the USB cable is
The lamp is off
inserted to a printer
Power on
When the printer is printing
When the AF activates
The lamp blinks
The lamp turns on
(The camera focus on the subject)
The lamp blinks
(The camera doesn't focus on the subject)
《11》
Connecting to a Power Source
You should use the rechargeable battery SLB-0837(B) supplied with the
camera. Be sure to charge the battery before using the camera.
Battery life / Number
of images
■ SLB-0837(B) rechargeable battery Specification
Model
Type
Capacity
Voltage
SLB-0837(B)
Lithium Ion
800mAh
3.7V
Charging time
(When the camera is turned off)
Approx. 150 MIN
■ Number of images and battery life : Using the SLB-0837(B)
Battery life / Number
of images
Still image
《12》
Approx. 100 MIN /
Approx. 200 shots
Conditions
Using the fully charged battery, Auto mode,
8M image size, Fine image quality,
Shot to shot interval : 30Sec.
Changing the zoom position between
the Wide and the Tele after every shot.
Using the flash on every second shot.
Using the camera for 5 minutes and
then Powering it off for 1 minute.
Movie
Approx. 75 MIN
Conditions
Using the fully charged battery
640x480 image size
30fps frame rate
※ These figures are measured under Samsung’s standard conditions and
shooting conditions and may vary depending on the user’s methods.
Important information about battery usage.
● When the camera is not used, turn off the camera power.
● Please remove the battery if the camera will not be used for long
periods. Batteries can lose power over time and are prone to leaking if
kept inside the camera.
● Low temperatures (below 0°C) can affect the performance of the
battery and you may experience reduced battery life.
● Batteries will usually recover at normal temperatures.
● During extended use of the camera, the camera body may become
warm. This is perfectly normal.
Connecting to a Power Source
You can charge the rechargeable battery SLB-0837(B) by using the SAC-45
KIT which consists of the AC adapter (SAC-45) and the USB cable (SUC-C2).
When the SAC-45 and SUC-C2 are combined, they can be used as an AC
cable.
● Using an AC cable
: Connect the AC adapter to the USB cable.
It can be used as a power cable.
Important information about USB cable usage.
● Use a USB cable (SUC-C2) with the correct specification.
● If the camera is connected to the PC through a USB hub :
connect the camera directly to the PC.
● If the camera and other devices are connected to the PC at the same
time : remove other device.
● If the USB cable is connected to a port located on the front of the PC :
remove the cable and connect it to a port located on the back of the
PC.
● If the USB port of the PC doesn't meet the Power output standard
(5V, 500mA), the camera may not be charged.
● Using a USB cable
: Remove the AC adapter (SAC-45).
You can download stored images to your PC
(p.103) or supply the power to your camera
through the USB cable.
《13》
Connecting to a Power Source
■ How to charge the rechargeable battery (SLB-0837B)
■ Charging LED of the AC Adapter
Charging LED
Being Charged
Charging is complete
Green LED is on
Charging error
Red LED is off or blinking
Being discharged
Charging LED
Red LED is on
(Using the AC adapter)
Orange coloured LED is on
- If you insert the fully discharged battery to charge it, do not turn on the camera at
the same time. This is because of the low battery capacity. Charge the battery for
more than 10 minutes before using the camera.
- Do not use the flash frequently or take a movie clip with the fully discharged
battery charged for a short time. Even if the charger is inserted, the camera
power may be turned off because the rechargeable battery is discharged again.
● Before inserting any cables or AC adapter, check the directions and
do not insert by force. It may cause breakage of cable or camera.
● If the charging LED of the AC Charger does not turn on or blink after
inserting the rechargeable battery, please check whether the battery
is inserted correctly.
● If you charge the battery with the camera power on, the battery can't
charge fully. Turn the camera off while charging the battery.
《14》
Connecting to a Power Source
Inserting the memory card
Insert the battery as shown
Insert the memory card as shown.
- If the camera does not turn on after you
have inserted battery, please check
whether the battery is inserted with the
correct polarity (+ / -).
- When the battery chamber cover is
opened, do not force it. This may cause
damage to the battery
- Turn off the camera’s power before
inserting the memory card.
- Have the front of the memory card facing
toward the front of the camera (Lens) and
the card pins toward the back of the
camera (LCD monitor).
- Do not insert the memory card the wrong way round.
Doing so may damage the memory card slot.
■ There are 4 indicators for battery condition that are displayed on the LCD
monitor.
Battery
indicator
Battery
status
The battery is
fully charged
Low battery
capacity
(Prepare to
recharge
or use spare
battery)
Low battery
capacity
Prepare to
recharge
or use spare
battery)
Battery empty.
Recharge or
use spare
battery.
《15》
Instructions on how to use the memory card
● Be sure to format the memory card (see p.61) if you are using a newly
purchased memory for the first time, if it contains data that the camera cannot
recognise, or if it contains images captured with a different camera.
● Turn off the camera power whenever the memory card is being inserted or
removed.
● Repeated use of the memory card will eventually reduce the memory card’s
performance. Should this be the case, you will need to purchase a new memory
card. Wear and tear on the memory card is not covered by the Samsung
warranty.
● The memory card is an electronic precision device.
Do not bend, drop or subject the memory card to any heavy impact.
● Do not store the memory card in an environment with strong electronic or
magnetic fields, e.g. near loud speakers or TV receivers.
● Please do not use or store in an environment where there are extremes in
temperature.
● Do not allow the memory card to become dirty or to come into contact with any
liquid. Should this happen, clean the memory card with a soft cloth.
● Please keep the memory card in its case when not in use.
● During and after periods of extended use, you may notice that the memory card
is warm. This is perfectly normal.
● Do not use a memory card that is used in another digital camera. To use the
memory card in this camera, format the memory card using this camera.
● Do not use a memory card formatted by another digital camera or memory card
reader.
《16》
● If the memory card is subjected to any of the following, the recorded data may
become corrupted :
- When the memory card is used incorrectly.
- If the power is switched off or the memory card is removed while recording,
deleting (formatting) or reading.
● Samsung cannot be held responsible for lost data.
● It is advisable to copy important data onto other media as back-up e.g. floppy
disks, hard disks, CD etc.
● If there is insufficient memory available :
A [Memory Full!] message will appear and the camera will not operate.
To optimise the amount of memory in the camera, replace the memory card or
delete unnecessary images stored on the memory card.
● Don't remove the memory card when the camera status lamp is
blinking as this may cause damage to data in the memory card.
Instructions on how to use the memory card
The camera can use SD/ SDHC Memory Cards and MMC (Multi Media
Cards).
Card pins
When using a 256MB MMC memory, the specified shooting capacity will be
as follows. These figures are approximate as image capacities can be
affected by variables such as subject matter and memory card type.
Recorded
image size
Super
Fine
Fine
Normal
30FPS
20FPS
15FPS
57
103
180
-
-
-
68
115
206
-
-
-
84
134
233
-
-
-
93
158
271
-
-
-
172
265
425
-
-
-
558
663
742
-
-
-
-
-
-
-
About 6'57" About 8'44"
* Movie
-
-
-
-
About 9'20" About 11'52"
clip
-
-
-
About 11'07" About 14'10" About 17'52"
-
-
-
About 21'07" About 27'25" About 37'18"
Write protect
switch
Label
[SD (Secure Digital) memory card]
The SD/ SDHC memory card has a write protect switch that prevents image files
from being deleted or formatted. By sliding the switch to the bottom of the SD
memory card, the data will be protected. By sliding the switch to the top of the SD
memory card, the data protection will be cancelled.
Slide the switch to the top of the SD memory card before taking a picture.
Still
image
※ The recording times can be changed by the zoom operation.
The zoom button doesn’t function during the movie recording.
《17》
LCD monitor indicator
■ The LCD monitor displays information about the shooting functions and
selections.
①
No.
⑳
Description
Icons
Page
7
Contrast
p.51
8
Sharpness/Mic. Off
p.51/53
p.19/51
⑲
9
Auto Focus Frame
②
⑱
10
Camera shake Warning
③
⑰
11
Date / Time
④
⑯
12
Exposure compensation
/ LongTime Shutter
⑤
⑮
13
White Balance
p.48
⑥
⑭
14
ISO
p.47
⑦
⑬
15
Drive mode / Stabiliser
p.46/50
⑧
⑫
16
Metering
p.46
17
Image Quality / Frame Rate
p.45
18
Image Size
p.45
19
Battery
p.15
20
Optical / Digital Zoom bar /
Digital Zoom rate
p.24
21
Voice Memo
p.52
22
Number of available shots
remaining / Remaining time
23
Memory card icon /
Internal memory icon
⑨
⑩
⑪
[Image & Full Status]
No.
Description
Icons
Page
1
Recording mode
p.11
2
Color / Saturation
p.35/37
3
Face Recognition
p.26
4
Flash
p.29
5
Self-timer
6
Macro
《18》
p.31
MF
p.27
p.23
2007/06/01 01:00 PM
/ LT
6/00:00:00
p.57
p.49
p.17
-
Changing the recording mode
Starting the recording mode
You can select the desired working mode by the M (mode) button located on
the back of the camera. Auto, Program, movie clip, ASR, scene (night,
portrait, children, landscape, close-up, text, sunset, dawn, backlight, fireworks,
beach & snow, Self-shot, Food, Cafe) camera modes are available.
How to use the Auto mode
■ Selecting the camera mode
1. Insert the battery (p.15).
2. Insert the memory card (p.15). As this camera has a 19MB internal memory, it
is not essential to insert the memory card. If the memory card is not inserted,
an image will be stored in the internal memory. If the memory card is inserted,
an image will be stored on the memory card.
3. Close the battery chamber cover.
4. Press the power button to turn on the camera.
5. Press the M button and a menu for selecting
recording menu will be displayed.
6. You can select a mode by pressing the 5 function
AUTO
button.
Up / Down button : moves the cursor between
SHOOTING MENU and
SCENE MENU mode.
SCENE
Left / Right button : moves the cursor between
[Mode selection menu]
each modes.
7. Press the OK button and a recording mode is set.
Select this mode for quick and easy picture taking with minimal user
interaction.
1. Select the Auto mode by pressing the M (Mode)
button (p.33).
2. Point the camera towards the subject and
compose the image by using the LCD monitor.
3. Press the shutter button to capture an image.
●If the auto focus frame turns to red when you press the shutter button
down half way, it means that the camera cannot focus on the subject.
Should this be the case, the camera is less likely to capture an image
clearly.
●Avoid obstructing the lens or the flash when you capture an image.
《19》
Starting the recording mode
How to use the Program mode
How to use the ASR mode
Selecting the automatic mode will configure the camera with optimal settings
and you can manually configure various functions.
This mode will reduce the effect of camera shake and help you get a wellexposed image in dim conditions.
1. Select the Program mode by pressing the M
(Mode) button (p.33).
2. Point the camera towards the subject and
compose the image by using the LCD monitor.
3. Press the shutter button to capture an image.
※ Refer to page 34-53 for more information about
the Program mode menus.
1. Select the ASR mode by pressing the M (Mode)
button. (p.33)
2. Point the camera towards the subject and
compose the image by using the LCD monitor.
3. Press the shutter button to capture an image.
■ Things to watch out for using the ASR mode
- The digital zoom will not operate in the ASR mode.
- If the lighting condition is brighter than fluorescent lighting conditions, the ASR
will not activate.
- If the lighting condition is darker than in fluorescent lighting conditions, camera
shake warning indicator (
) will display. For best results only take pictures
in situations where the camera shake warning indicator (
) is not displayed.
- If the subject is moving, the captured image may be blurred.
- Avoid moving the camera while the [Capturing!] message is displayed to
achieve a better result.
- As the ASR uses the camera's digital signal processor, it may take a little
longer for the camera to process and save the images.
《20》
Starting the recording mode
How to use the Movie clip mode
Pausing while recording a movie clip (Successive Recording)
A movie clip can be recorded for as long as the available recording time of the
memory capacity allows.
This camera allows you to temporarily stop during unwanted scenes, while
recording a movie clip. Using this function, you can record your favourite scenes
into a movie clip without having to create multiple movie clips.
1. Select the Movie clip mode by pressing the M
(Mode) button.(p.33)
2. Point the camera towards the subject and
compose the image by using the LCD monitor.
3. Press the shutter button once and movie clips are
recorded for as long as the available recording
time allows. Movie clips will still be recorded if the
shutter button is released.
If you wish to stop recording, press the shutter button again.
※ Image size and type are listed below.
- Image size
: 800x592, 720x480, 640x480, 320x240
- Movie clip file type : AVI (MPEG-4)
- Frame Rate
: 30FPS, 20FPS, 15FPS
- When the 800X592 or 720X480 image size is selected, the 30FPS can't be selected.
■ Using Successive Recording
Steps from 1-2 are the same as those for MOVIE
CLIP mode.
3. Point the camera towards the subject and
compose the image by using the LCD monitor.
Press the shutter button and movie clips are
00 : 00 : 18
/‖ Record
SH Stop
recorded for as long as the available recording
time. Movie clips will still be recorded if the
shutter button is released.
4. Press the Pause button (
) to pause recording.
5. Press the Pause button (
) again to resume the recording.
6. If you wish to stop recording, press the shutter button again.
Recording the movie clip without sound
You can record the movie clip without sound.
Steps from 1-3 are the same as those for MOVIE
CLIP mode.
4. Press the Menu button.
5. Select the [RECORDING] menu by pressing the
Left / Right button.
6. Press the Down button to select the [Voice Mute]
menu and press the Right button.
7. Select the [On] menu by pressing the Up / Down button.
8. Press the OK button. You can record a movie without sound.
《21》
Starting the recording mode
How to use the Scene modes
Use the menu to easily configure optimal settings for a variety of shooting
situations.
1. Select the Scene mode by pressing the M (Mode)
button (p.33).
2. Point the camera towards the subject and
compose the image by using the LCD monitor.
3. Press the shutter button to capture an image.
■ The scene modes are listed below.
[NIGHTSCENE] (
[PORTRAIT] (
[CHILDREN] (
)
)
)
[LANDSCAPE] (
)
[CLOSE UP] (
)
[TEXT] (
)
[SUNSET] (
)
[DAWN] (
)
[BACKLIGHT] (
《22》
)
: Use this for shooting still images at night or in other
dark conditions.
: To take a picture of a person.
: To take a picture of fast moving objects, for
example, children.
: To take pictures of distant scenery.
: Close-up shooting for small objects such as plants
and insects.
: Use this mode to shoot a document.
: For taking pictures of sunsets.
: Daybreak scenes.
: Portrait without shadows caused by backlight.
[FIREWORK] (
)
[BEACH&SNOW] (
[SELF SHOT] (
)
[FOOD] (
[CAFÉ] (
)
)
: Firework scenes.
) : For ocean, lake, beach and snowscape scenes.
: Use when the photographer would also like to
appear in the image.
: For taking delicious looking food.
: For taking pictures in cafes and restaurants.
Things to Watch Out for When Taking Pictures
● Pressing the shutter button down half way.
Lightly press the shutter button to confirm focus and flash battery charge.
Press the shutter button all way down to take the picture.
[Lightly press the shutter button]
● Under certain conditions the auto focus system may not perform as expected.
- When photographing a subject that has little contrast.
- If the subject is highly reflective or shiny.
- If the subject is moving at high speed.
- When there is strong reflected light, or when the background is very bright.
- When the subject matter has only horizontal lines or the subject is very narrow
(such as a stick or flagpole).
- When the surroundings are dark.
[Press the shutter button]
● The available memory capacity may vary depending on shooting conditions and
camera settings.
● When the Flash Off or Slow synchro mode is selected in a low lighting condition,
the camera shake warning indicator (
) may appear on the LCD monitor.
In this case, use a tripod, support the camera on a solid surface or change to
flash shot mode.
● Shooting against the light : Please do not take pictures against the sun.
Doing so may make the picture dark. To take a
picture against the sun, please use the [BACKLIGHT]
in the scene shooting mode (see page 22), fill-in flash
(see page 29), spot metering (see page 46), or
exposure compensation (see page 49).
● Avoid obstructing the lens or the flash when you capture an image.
● Compose the image by using the LCD monitor.
《23》
Using the camera buttons to set the camera
ZOOM W / T button
The recording mode function can be set up by using the camera buttons.
If the menu is not displayed, this button works as
the OPTICAL ZOOM or DIGITAL ZOOM button.
This camera has a 3X optical zoom and a 5X
digital zoom function.
Using both will offer a total zoom ratio of 15X.
POWER button
Used for turning the camera’s power on / off.
If there is no operation during the specified time, the
camera's power will be turned off automatically to
save battery life.
Refer to page 59 for more information about the auto
power off function.
■ TELE Zoom
Optical zoom TELE
Digital zoom TELE
SHUTTER button
Used for taking an image or recording voice in the RECORDING mode.
● In MOVIE CLIP mode
Pressing the shutter button down fully starts the
process for recording a movie clip.
Press the shutter button once and the movie clip
is recorded for as long as the available recording
time in the memory allows. If you wish to stop
recording, press the shutter button again.
● In STILL IMAGE mode
Pressing the shutter button down halfway activates the autofocus and checks
the condition of the flash. Pressing the shutter button down fully takes and stores
the image. If you select voice memo recording, the recording will start after the
camera has finished storing the image data.
《24》
: Pressing the ZOOM T button. This will zoom into the
subject i.e. the subject will appear nearer.
: When the maximum (3X) optical zoom is selected,
pressing the ZOOM T button activates the digital zoom
software. Releasing ZOOM T button stops the digital
zooming at the required setting. Once the maximum
digital zoom (5X) is achieved, pressing the ZOOM T
button will have no effect.
Pressing
the ZOOM
T button
[WIDE zoom]
Pressing
the ZOOM
T button
[TELE zoom]
[Digital zoom 5.0X]
ZOOM W / T button
■ WIDE Zoom
Optical zoom WIDE
: Pressing the ZOOM W button. This will zoom out from
the subject i.e. the subject will appear further away.
Pressing the ZOOM W button continuously will set the
camera to its minimum zoom setting i.e. the subject
appears at its furthest from the camera.
Pressing
the ZOOM
W button
Pressing
the ZOOM
W button
Digital zoom WIDE
Optical zoom
Digital zoom
: When the digital zoom is in operation, pressing the
ZOOM W button will reduce the digital zooming in
steps. Releasing ZOOM W button stops digital
zooming. Pressing the ZOOM W button will reduce the
digital zoom and then it will continue to reduce the
optical zoom until the minimum setting is reached.
Pressing
the ZOOM
W button
[Digital zoom 5.0X]
[WIDE zoom]
[Optical zoom 2X]
[TELE zoom]
● Images taken using the digital zoom may take a little longer for the
camera to process. Allow time for this to take place.
● The digital zoom cannot be used in movie clip shots.
● You may notice a decrease in image quality when using the digital
zoom.
● To view a clearer digital zoom image, press the shutter button halfway
at the maximum optical zoom position and press the zoom T button
again.
● The digital zoom can't be activated in some Scene modes (Night,
Children, Text, Close-up, Fireworks), Motion Capture mode, ASR mode
and the movie clip mode.
● Take care not to press the lens as this may cause a camera
malfunction.
Pressing
the ZOOM
W button
[TELE zoom]
[WIDE zoom]
《25》
Face recognition(FR) button
This mode detects the face position of the subject automatically and then sets
the focus and exposure. Select this mode for quick and easy face picture.
※ Selectable modes : Auto, Program, ASR, Scene modes
(Portrait, Children, Beach & Snow, Self-shot, Cafe)
1. Press the FR (Face Recognition) button
(
) in the selectable modes.
The FR icon will be displayed on the screen
left side.
2. The size and position of the auto focus frame is
set at the face of the subject automatically.
3. Press the shutter button halfway. The focus frame turns to green when the
focus is activated.
4. Press the shutter button fully to take a picture.
《26》
● This function can detect up to 9 persons.
● When the camera recognises many people at the same time, it will
focus on the nearest person.
● The Digital zoom is not activated in this mode.
● The effects functions are not activated in this mode.
● When the camera detects a target face, the white colour focus frame
will be displayed over the target face and the gray colour focus frame
appear over the remaining faces(up to 8). Press the shutter button
halfway down to focus on the face and the white focus frame turns
green.(Total 9)
● Return to previous AF mode if face detection was failure.
● In some conditions this function cannot work properly.
- When a person wears dark glasses or some part of the face is hidden.
- When the person being taken does not look at the camera.
● The maximum available Face Recognition range is 2.5m (Wide).
● The nearer the subject, the faster the camera can recognize the
subject.
Info (
Macro (
) / Up button
While the menu is showing, the Up button operates as a direction button.
In the recording modes or playback mode, pressing this button will display the
image information.
Info (
) / Down button
While the menu is showing, press the DOWN button to move from the main
menu to a sub menu, or to move down the sub menu. When the menu is not
showing, you can use the MACRO / DOWN button to take macro pictures.
The distance ranges are shown below. Press the Macro button until the
desired macro mode indicator appears on the LCD monitor.
) button
[Auto Focus]
[Auto Macro (
[Manual Focus]
[Macro (
)]
)]
[Super Macro (
)]
※ When the manual focus is selected, a bar
for selecting the focus distance appears.
The focus bar displayed on the LCD
monitor is for your reference. To get the
exact focus range, refer to the image
displayed on the LCD monitor.
- Left/Right : Selecting the Focus distance
- OK button : Setting up the focus.
《27》
Macro (
) / Down button
■ Types of focus mode and focus range (W : Wide, T : Tele)
Mode
Focus Type
Focus range
Mode
Focus Type
Auto (
Super macro (
)
Super macro (
)
■ Available focusing method, by recording mode
(● : Selectable, ∞ : Infinity focus range)
)
Auto macro (
)
W : 5 ~ Infinity
T : 40 ~ Infinity
W:1~5
(Wide only)
(Unit : cm)
Normal
Mode
●
W : 80 ~ Infinity
T : 80 ~ Infinity
Program (
)
Macro ( )
Normal
Mode
Focus Type
Focus range
W:1~5
(Wide only)
Super macro (
W:1~5
(Wide only)
W : 5 ~ 80
T : 40 ~ 80
●
Manual Focus
)
W : 80 ~ Infinity
T : 80 ~ Infinity
Macro
●
●
Mode
Focus range
Auto macro Super macro
Auto macro Super macro
Normal
●
●
●
●
●
●
SCENE
Macro
Normal
1cm ~ Infinity
●
●
ASR mode (
)
Macro ( )
Normal
W : 5 ~ 80
T : 40 ~ 80
W : 80 ~ Infinity
T : 80 ~ Infinity
●
∞
●
●
∞
● When the macro mode is selected, be particularly careful to avoid
camera shake.
● When you take a picture within 20cm (Wide zoom) or 50cm
(Tele zoom) in the Macro mode, select the FLASH OFF mode.
● When you take a picture within the 5cm Super macro range, the autofocus on the camera will take longer to set the correct focus distance.
∞
●
∞
●
●
●
●
《28》
MF
●
●
Focus lock
Flash (
To focus on a subject not positioned in the centre of the picture, use the focus
lock function.
When the menu is displayed on the LCD monitor,
pressing the LEFT button makes the cursor shift to
the left tab.
When the menu is not displayed on the LCD
monitor, the LEFT button operates as the FLASH
button.
■ Using the Focus Lock
1. Ensure the subject is in the centre of the autofocus frame.
2. Press the SHUTTER button halfway. When the green auto focus frame lights
up, it means the camera is focused on the subject. Be careful not to press the
SHUTTER button all the way down to avoid taking an unwanted picture.
3. With the SHUTTER button still pressed down only halfway, move the camera
to recompose your picture as desired, and then press the SHUTTER button
completely to take the picture. If you release your finger from the SHUTTER
button, the focus lock function will be cancelled.
) / Left button
[Selecting the Auto flash]
■ Selecting the flash mode
1. Press the Mode button to select a RECORDING mode with the exception of
the Movie clip mode or the ASR mode. (p.33)
2. Press the Flash button until the desired flash mode indicator is displayed on
the LCD monitor.
3. A flash mode indicator will be displayed on the LCD monitor.
Use the correct flash to suit the environment.
■ Flash range
1. The image to be
captured.
2. Press the SHUTTER
button halfway and
focus on the subject.
3. Recompose the picture
and fully depress the
SHUTTER button.
ISO
AUTO
(Unit : m)
Normal
Macro
Auto macro
WIDE
TELE
WIDE
TELE
WIDE
TELE
0.8 ~ 3.0
0.5 ~ 2.5
0.2 ~ 0.8
0.5 ~ 0.8
0.2 ~ 3.0
0.5 ~ 2.5
※ When the Super Macro is selected, flash is fixed as the Flash Off mode.
《29》
Flash (
) / Left button
● If you press the shutter button after selecting the Auto, Fill-in, Slow
synchro flash, the first flash fires to check the shooting condition (Flash
range and Power ratio of flash).
Do not move the camera until the second flash fires.
● Using the flash frequently will reduce the life of the battery.
● Under normal operating conditions the re-charging time for the flash is
usually within 4 seconds. If the battery is weak, the charging time will
be longer.
● In the ASR mode, [LANDSCAPE], [CLOSE UP], [TEXT], [SUNSET],
[DAWN], [FIREWORK], [SELF SHOT], [FOOD], [CAFÉ] scene modes
and the Movie clip mode, the flash function will not operate.
● The image quality is not guaranteed if the subject is too close or highly
reflective.
● When taking an image in poorly lit conditions with the flash, there may
be a white speck in the captured image. The speck is caused by the
the flash light reflecting off atmospheric dust.
■ Flash mode indicator
Icon
Flash mode
Description
Auto flash
If the subject or background is dark, the camera
flash will operate automatically.
Auto &
Red eye
reduction
If a subject or background is dark, the camera flash
will work automatically and will reduce the red-eye
effect by using the red-eye reduction function.
Fill in flash
The flash fires regardless of the available light.
The intensity of the flash will be automatically
controlled to suit the prevailing conditions.
Slow synchro
《30》
The flash operates with a slow shutter speed to
obtain a balanced correct exposure.
In poor lighting conditions the camera shake
warning indicator (
) will display on the LCD
monitor.
Flash off
The flash does not fire.
Select this mode when capturing images in a place
or situation where flash photography is prohibited.
When you capture an image in a poorly lit condition,
the camera shake warning indicator (
) will
appear on the LCD monitor.
Red-eye
reduction
When a shot with "red eye" is detected, this mode
will reduce the red-eye effect automatically.
Flash (
) / Left button
Self-timer (
■ Available flash mode, by recording mode
●
●
●
●
●
(●: Selectable)
●
●
●
●
●
) / Right button
When the menu is displayed on the LCD monitor, pressing the Right button
makes the cursor shift to the right tab.
When the menu is not displayed on the LCD monitor, the RIGHT button
operates as the Self-timer (
) button. This function is used when the
photographer would also like to be in the image.
●
●
●
●
●
●
●
●
●
●
●
● If you operate the Self-timer button during the self-timer operation, the
self-timer function is cancelled.
● Use a tripod to prevent the camera from shaking.
● In Movie Clip mode, only the 10SEC self-timer and motion timer will
work.
●
●
●
●
●
●
●
●
●
●
●
《31》
Self-timer (
) / Right button
■ Selecting the self-timer
1. Select a RECORDING mode with the exception of VOICE RECORDING
mode. (p.33)
2. Press the SELF-TIMER (
) button until the desired mode indicator
displays on the LCD monitor. A 10 second, 2 second, Double self-timer or
Motion timer icon appears on the LCD monitor.
•10SEC self-timer (
):
Pressing the shutter button will allow an interval
of 10 seconds before the image is taken.
•2SEC self-timer (
):
Pressing the shutter button will allow an interval
of 2 seconds before the image is taken.
•Double self-timer (
):
[Selecting the 10 SEC self-timer]
A picture will be taken after about 10 seconds
and 2 seconds later a second picture will be
taken. When using the flash, the 2-second self-timer may be delayed for
longer than 2 seconds depending on the flash charging time.
•Motion Timer (
) :
The camera detects the subject's movement 6 seconds after pressing the
Shutter button, and the picture is taken when the movement is stopped.
3. When you press the SHUTTER button, the picture will be taken after the
specified time has elapsed.
《32》
■ Motion Timer
Icon & Self-timer lamp
Motion
Pressing the Shutter button after setting
Blink (1 second interval)
the Motion Timer
Detecting the subject's movement
Blink (0.25 second interval)
No movement is detected
Turn on and the image is taken after
2 seconds.
■The Motion Timer flows are as followings.
Selecting the Motion Timer → Pressing the Shutter button → Confirming the
composition (Within 6 sec.)*1 → Starting the detection (Swing your hands fully)*2
→ Stopping the detection (Do not move) → Taking an image (after 2 sec.)
*1 : The camera detects the subject's movement 6 seconds after pressing the
Shutter button, so confirm the composition within 6 seconds.
*2 : Move your body or hands fully.
In the following cases, the Motion Timer may not operate.
● The focus distance is over 3m.
The detection range of Motion Timer
● The exposure is too bright or dark
● In backlight conditions.
● The movement is insignificant
● The movement is detected out of the
center part (50%) of the sensor
where the movement is recognized.
MENU / OK button
M (Mode) button
■ MENU button
You can select the desired recording mode.
- When you press the MENU button, a menu related to each camera mode will
be displayed on the LCD monitor. Pressing it again will return the LCD to the
initial display.
- A menu option can be displayed when the following are selected :
MOVIE CLIP and STILL IMAGE mode. There is no menu available when the
VOICE RECORDING mode is selected.
[Auto mode]
RECORDING
[Pressing the MENU button]
Sharpness
Contrast
Auto Focus
Voice Memo
Voice Record
[Menu off]
Move
■ How to use the mode button
Normal
Normal
Center AF
Off
PROGRAM
[Pressing the Mode button]
MENU
[Pressing the Right button]
Exit
[Menu on]
SCENE
AUTO
[Program mode]
■ OK button
- When the menu is displayed on the LCD monitor, this button is used for shifting
the cursor to the sub menu or for confirming data.
ASR
SCENE
[Mode selection menu]
[Pressing the Left button]
SCENE
[ASR mode]
[Pressing the Down button]
SHOOTING
SHOOTING
NIGHTSCENE
PORTRAIT
[Pressing the Left / Right button]
[Scene mode]
[Selecting a scene mode]
《33》
E (Effect) button
It is possible to add special effects to your images by using this button.
■ Still image mode : You can select the colour, special colour, image editing
and Fun menu. In the Auto mode, you can select the
[COLOR] menu only.
■ Movie clip mode : You can select the colour menu.
■ Available Effects, by recording mode
(●: Selectable)
●
●
《34》
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
● This button will not operate in ASR, Voice recording mode and some
scene modes (Night, Text, Sunset, Dawn, Backlight, Fireworks,
Beach&Snow).
● Even if the camera is turned off, the effect setting will be preserved.
To cancel the special effect, select
sub menu in the Colour
menu and select the
sub menu in the rest effect menus.
● If the image size is
or
, the FUN menu can't be selected.
E (Effect) button : Colour
By using the camera’s digital processor, it is possible to add special effects
to your images
■ Custom colour : You can change the R (Red),
G (Green) and B (Blue) values of
the image.
Custom Color
■ Press the E button in an available recording mode. (p.34)
Move
- Up/Down button : Selects R, G, B
- Left/Right button : Changes the values
OK
Set
OK
Set
COLOR
COLOR
Move
이동
E
Exit
해제
[Still image mode]
Move
E
Custom Color
Exit
[Movie clip mode]
Move
1. Select a desired sub menu by pressing the Up/Down button and press the OK
button.
: No effect is added to the image.
: Captured images will be stored in black and white.
: Captured images will be stored in a sepia tone
(a gradient of yellowish brown colours).
: Captured images will be stored in a red tone.
: Captured images will be stored in a green tone.
: Captured images will be stored in a blue tone.
: Save the image in negative mode.
: Captured image will be saved in set RGB tone.
※ In the Auto mode, the Custom Color can't be selected.
2. Press the shutter button to capture an image.
《35》
E (Effect) button : Colour Mask
With this menu, you can select a part you want to highlight. The rest of the image will be black and white.
■ Press the E button in an available recording mode. (p.34)
Color Mask
Press the OK button and the Mask mark
will be displayed on the LCD monitor.
Press the Fn button. You can change the
size and location of the mask.
Capture
OK Set
EE
SH Capture
Back
Fn
E Edit
Move
TW
E Size
Zoom W / T button :
Changing the Mask size
Capture
Move
Press the Shutter button and the mask
added image is taken.
[Final image]
Pressing the Fn button.
SH Capture
TW
E Size
Up/Down/Left/Right button :
Moving the mask
Fn
E Edit
[Mask added image]
Capture
Move
《36》
TW
E Size
E (Effect) button : Saturation
You can change the saturation of the image.
■ Press the E button in an available recording mode. (p.34)
IMAGE ADJUST
Move
Saturation
E
Exit
Select Saturation menu (
) and a bar
for changing the saturation will be
displayed.
Change the saturation by pressing the
Left/Right button.
Move
OK
Set
Saturation
Bar for changing the saturation
Move
OK
Set
+ direction: High saturation (The colour will be intense)
- direction: Low saturation (The colour will be subtle)
Press the Shutter button to take a picture.
Press the OK button and the saturation of
image will be changed.
[Final Image]
《37》
E (Effect) button : FUN
Cartoon
You can add a text box on the image to make the image cartoon like.
■ Press the E button in an available mode. (p.34)
FUN
Press the Fn button and select a
desired text box position by
pressing the Left/Right button
Cartoon
Select Cartoon (
Move
)
Select a desired frame by
pressing the Left/Right button
and press the OK button.
EE Exit
Frame
OK
E Set
Select the text box position of
the third image with the same
procedure and take the third
image.
SH Capture
Fn Edit
Move
Press the OK button and the file is saved
as a new file name
《38》
Fn Delete
Fn Edit
SH Capture
Move
Press the Shutter button to
take an image
SH Capture
OK Save
SH Capture
E (Effect) button : FUN
■ Before saving the cartoon image, you can take images again.
1. Select an image to delete by using the Left/Right button.
2. Press the Fn button and the image deletes.
Pressing the Fn button
SH Capture
Move
OK Save
Fn Delete
3. To take a new image, press the Shutter button.
《39》
E (Effect) button : FUN
Pre-set focus frame
You can make the subject stand out from its surroundings. The subject will be
sharp and in focus while making the rest out of focus.
■ Moving and changing the focus frame
You can change the focus frame after selecting a Range menu.
■ Press the E button in an available recording mode. (p.34)
Pressing the Fn button
FUN
High light
SH Capture
Fn
E Edit
SH Capture
[Point the camera towards the
subject and compose the image
by using the LCD monitor.]
Move
Range
EE Exit
E Move
[The range is activated : The
colour of focus frame turns white.]
Pressing the
Up/Down/Left/Right
button
OK
E Set
1. Select a proper menu by pressing the Left/Right button and press the OK
button.
High light
High light
High light
Pressing the Fn button
High light
SH Capture
Range
OK
E Set
[Range 1]
Range
OK
E Set
[Range 2]
Range
OK
E Set
Range
[Range 3]
Fn Edit
[Range 4]
Pressing the shutter button
2. The preset focus frame will appear.
Press the shutter button to capture an image.
SH Capture
《40》
Fn
E Edit
SH Capture
E Move
[After changing the range]
OK
E Set
[Final image]
E (Effect) button : FUN
Composite shooting
※ Selecting 2 composite shots
You can combine 2 - 4 different shots in a still image.
Pressing the
shutter button
■ Press the E button in an available recording mode. (p.34)
SH Capture
SH Capture
[Ready for taking]
Composite
FUN
Fn Delete
[First shot]
Pressing the shutter
button
Move
E Set
Composite OK
EE Exit
Pressing the
OK button
1. Select a desired menu by pressing Left/Right button and press the OK button.
Composite
Composite
Composite
Composite
OK Save
[The final picture]
E
Composite OK
Set
[Composite 1]
E
Composite OK
Set
[Composite 2]
E
Composite OK
Set
[Composite 3]
E
Composite OK
Fn Delete
[Second shot]
Set
[Composite 4]
After taking the last image, press the OK button to save the image.
2. After selecting a desired menu, press the shutter button to take a picture.
● You can use the flash, self-timer, macro focus and the Zoom W / T
button during the composite shooting.
● If you press the Play mode, MENU, E button or Mode button during the
composite shots, each camera working mode is executed.
The previously captured images will be deleted.
《41》
E (Effect) button : FUN
■ Changing a part of composite shot before taking the last shot
Before taking the last composite shot, you can change a part of composite
shot.
1. During the composite shots, press the Fn button.
2. A previous image will be deleted and new frame will be displayed.
To delete a previously taken image, press the Fn button again.
■ Changing a part of composite shot after taking the last shot
1. After taking the last shot, a cursor to select a frame will appear.
Press the Up/Down/Left/Right button to select the frame.
2. Press the Fn button and an image will be deleted. Composite frame will be
activated.
3. Press the Shutter button. You can take other images again by using the Press
the Up/Down/Left/Right button and Fn button.
4. Press the OK button again to save the captured image.
Pressing the up
button
Pressing the Fn button
SH Capture
Fn Delete
[Before taking the 3rd shot]
SH Capture
Fn Delete
[Moving backward to the 2nd shot]
OK Save
Fn Delete
OK Save
[After taking 4th shot]
Fn Delete
[Moving backward to the 2nd shot]
3. Press the shutter button to capture a new image.
Pressing the Fn
button
Pressing the
Shutter button
SH Capture
[Deleting 2nd shot]
Pressing the OK
button
OK Save
Fn Delete
[Taking 2nd shot again]
《42》
[Final Image]
E (Effect) button : FUN
Photo Frame
You can add 9 types of frame-like borders to a still image you want to capture.
Date & Time information will not be printed on the stored image taken with
Photo Frame menu.
■ Press the E button in an available recording mode. (p.34)
FUN
Photo Frame
Move
Frame
EE Exit
OK
E Set
Pressing the OK
button
2. The selected photo frame will be displayed. Press the shutter button to take a
picture.
Pressing the Fn
button
SH Capture
E Move
SH Capture
Fn
E Frame
1. Select a desired sub menu by pressing the Left/Right button and press the OK
button.
《43》
Fn button
How to use the Fn menu
You can use the Fn button to set the following menus.
(●: Selectable)
Page
Size
●
●
●
●
●
p.45
Quality/
Frame Rate
●
●
●
●
●
p.45
●
p.46
●
*1●
Metering
●
Drive
●
ISO
●
White Balance
●
EV
●
LT
Stabilisation
p.46
p.47
●
p.48
●
p.49
*2●
p.49
●
1. Press the Fn button in an available mode
2. Select a desired menu by pressing the Up / Down button. And then a sub
menu will display on the left bottom side of the LCD monitor.
SIZE
Up / Down
button
QUALITY
Fine
3264X2448
3. Select a desired menu by pressing the Left / Right button and then press the
OK button.
p.50
*1. This menu is only available in the Children scene mode (
).
*2. This menu is only available in the Night scene mode (
).
SIZE
3264X2448
《44》
Left / Right
button
SIZE
3264X2176
Size
Quality / Frame rate
You can select the image size appropriate for your application.
You can select the compression ratio appropriate for your application of the
captured images. The higher the compression ratio, the lower the picture quality.
Icon
Still
image
mode
Size
Movie clip
mode
Size
3264x
2448
3264x
2176
3264x
1824
2592x
1944
2048x
1536
1024x
768
Icon
Mode
STILL IMAGE mode
Sub menu Super Fine
800x592
720x480
640x480
320x240
File Format
jpeg
Fine
Normal
30FPS
20FPS
15FPS
jpeg
jpeg
avi
avi
avi
SIZE
SIZE
QUALITY
3264X2448
800X592
Fine
[ STILL IMAGE mode ]
[ MOVIE CLIP mode ]
● The higher the resolution, the lower the number of shots available
because high resolution images require more memory.
MOVIE CLIP mode
Icon
[ STILL IMAGE mode ]
FRAME RATE
20FPS
[ MOVIE CLIP mode ]
● This file format complies with the DCF (Design rule for Camera File system).
● JPEG (Joint Photographic Experts Group) :
JPEG is the image compression standard developed by the Joint
Photographic Experts Group. This type of compression is most
commonly used for compressing photos and graphics because it can
compress the files efficiently.
《45》
Metering
Drive mode
If you cannot obtain suitable exposure conditions, you can change the
metering method to take brighter pictures.
You can select continuous shot, and AEB (Auto Exposure Bracketing).
[Multi]
: Exposure will be calculated based on an
average of the available light in the image
area. However, the calculation will be
biased towards the centre of the image
METERING
area. This is suitable for general use.
[Spot] : Only the rectangular area in the centre of
Multi
the LCD monitor will be metered for light.
This is suitable when the subject in the
centre is exposed correctly, regardless of the back lighting.
[Center] : Exposure will be calculated based on an average of the available light
in the image area. However, the calculation will be biased towards the
centre of the image area. This is suitable for taking a picture of small
object like a flower or insects.
※ If the subject is not the centre of the focus area, do not use the spot metering
as this may result in an exposure error. In this circumstance, it is better to use
exposure compensation.
[Single]
[Continuous]
: Take one picture only.
: Images will be taken
continuously until the shutter
button is released.
[Motion Capture] : This takes 7 shots per second,
DRIVE
when the shutter is pressed
Single
and held down.
After completing the continuous shooting, images are saved
and the images play back on the Rear LCD. The maximum
number of shots is 30 and the image size is fixed as VGA.
[AEB]
: Take three pictures in a series in different exposures: short
exposure (-1/3EV), standard exposure (0.0EV) and over
exposure (+1/3EV).
[Interval Shooting]: You can take images with interval and number of images
set before.
Up / Down button : Selecting the Interval menu or Number
of image menu.
Left / Right button : Changing the numbers
(01 min-60 min / 02 pics-99 pics).
* After taking the first image, the LCD monitor turns off.
After taking the last image, the camera turns off.
* Before using the Interval shot, charge the battery fully.
If the battery is out during the shots, the last taken before the camera was
turned off.
[Wise Shot]
《46》
: Two images are taken at a time. One is taken in the Fill-In Flash
mode and the other is taken in the ASR mode.
Drive mode
● It is best to use a tripod for the AEB shooting as the time to save each
image file is longer and blurring caused by camera shake may occur.
● In the Wise shot mode, the shutter speed value shown on the LCD
monitor may be different to the actual shutter speed.
● If 7MP or 6MW image size is selected, the Wise Shot menu can't be
selected.
■ How to use the wise shot
1. Select the ASR mode bu pressing the
mode button.
2. Select the wise shot menu in the [DRIVE] menu.
3. Press the Shutter button to take image.
4. The captured images are displayed.
- To select an image, press the Left/Right button.
Image with Flash
D RIVE
W ise Sh o t
Image with the ASR mode
Enlarged image
Enlarged image
OK Save
E
ISO
You can select the ISO sensitivity when taking pictures.
The speed or specific light-sensitivity of a camera is rated by ISO numbers.
Move
- Press the E button and you can check the enlarged image by pressing the 5
function button.
- Press the E button again and the image is enlarged automatically.
[Auto] :
The camera's sensitivity is automatically changed
by variables such as lighting value or subject
brightness.
ISO
5. Press the OK / Shutter button and the selected image will be saved.
● High resolution and picture quality increases file saving time, which
increases stand-by time.
● If the [Continuous], [Motion Capture] or [AEB] sub menu is selected,
the flash will be off automatically.
● If less than 3 pictures are available in the memory, the AEB shooting is
not available.
[ISO 50, 100, 200, 400, 800, 1600 ] :
Auto
You can increase the shutter speed while the
same amount of light is present, by increasing the
ISO sensitivity. However, the image may be saturated in high luminance.
The higher the ISO value, the higher the camera’s sensitivity to light and
therefore the greater its capacity to take pictures in dark conditions. However,
the noise level in the image will increase as the ISO value increases, making
the image appear coarse.
《47》
White balance
The white balance control allows you to adjust the colours to appear more
natural.
[Auto WB]
: The camera automatically
selects the appropriate
white balance settings,
depending on the prevailing
WHITE BALANCE
lighting conditions.
[Daylight]
: For taking images outside.
Auto WB
[Cloudy]
: For taking images under a
cloudy and overcast sky.
[Fluorescent_H]
: For shooting under daylight fluorescent types of threeway fluorescent lighting.
[Fluorescent_L]
: Shooting under white fluorescent lighting.
[Tungsten]
: For shooting under tungsten (standard light bulb)
lighting.
[Custom Set]
: Allows the user to set the white balance according to the
shooting condition.
Different lighting conditions may cause a colour cast on your images.
《48》
■Using the Custom White Balance
White balance settings may vary slightly depending on the shooting
environment. You can select the most appropriate white balance setting for
a given shooting environment by setting up the custom white balance.
1. Select the CUSTOM (
) menu of the
White Balance and place a sheet of white
paper in front of the camera so that the
LCD monitor shows only white.
2. MENU/OK button : selects previous custom
white balance.
Shutter button : saves new custom white
balance.
White paper
- The custom white balance value will be applied, starting with the next picture
you take.
- The user configured white balance will be remain effective until it is
overwritten.
Exposure compensation
Long Time shutter
This camera automatically adjusts the exposure according to the ambient
lighting conditions.
You can also select the exposure value by using the Fn button.
This camera automatically adjusts the shutter speed and aperture values to
the shooting environment. However, in NIGHT SCENE mode, you can set the
shutter speed and aperture values to your preference.
■ Compensating Exposure
■ Changing the Shutter speed and Aperture value
1. Press the Fn button, and then use the UP and
DOWN buttons to select the exposure
compensation icon (
).
The exposure compensation menu bar will
appear as shown.
EXPOSURE VALUE
2. Use the LEFT and RIGHT buttons to set the
desired exposure compensation factor.
3. Press the Fn button again. The value you set will
be saved and the Exposure Compensation setup mode will close.
If you change the exposure value, the exposure indicator (
) will be
displayed on the bottom of the LCD monitor.
-2
-1
0
+1
1. Select the [NIGHTSCENE] scene mode. (p.22, 53)
2. Press the Fn button and Long Time shutter menu will be displayed.
3. Configure the Long Time shutter value with the 5 function button.
4. Press the Fn button again. The value you set will be saved and the mode will
switch to NIGHT SCENE mode.
+2
※ A negative exposure compensation value reduces the exposure.
Note that a positive exposure compensation value increases the exposure
and the LCD monitor will appear white or you may not get good pictures.
F3.5
1sec
Aperture Value
WIDE : AUTO, F3.5 ~ F6.3,
TELE : AUTO, F4.5 ~ F8.0
Shutter Speed
AUTO,1~15S
《49》
Movie Clip frame stabiliser
Using the LCD monitor to adjust the camera settings
This function helps stabilize images captured during movie recording.
You can select this menu only in the MOVIE CLIP mode. If the memory card
is not inserted, this function will not operate.
You can use the menu on the LCD monitor to set up recording functions.
■The items indicated by
Menu
[Off] : Movie clip frame stabilizer function is
disabled.
[On] : Prevents camera shake during movie
recording. The recording frame range will
become narrower than when you select
the [Off] menu.
Sub menu
Available mode
Soft+
Soft
Normal
Vivid
Vivid+
-
High
Normal
Low
-
Auto Focus
Center AF
Multi AF
Voice Memo
Off
On
Sharpness
STABILIZER
Off
are default settings.
Contrast
Page
p.51
p.51
p.51
p.52
~53
Voice Record
Voice Mute
Off
p.53
On
NIGHTSCENE PORTRAIT CHILDREN
LANDSCAPE CLOSE UP
Scene mode SUNSET
DAWN
TEXT
BACKLIGHT
FIREWORK BEACH&SNOW SELF SHOT
FOOD
CAFÉ
-
※ Menus are subject to change without prior notice.
《50》
p.53
Sharpness
You can adjust the sharpness of the picture you
are about to take. You cannot check the
sharpness effect on the LCD monitor before you
take a picture, because this function is applied
only when the captured image is stored on the
memory.
Auto Focus type
RECORDING
Sharpness
Contrast
Auto Focus
Voice Memo
Voice Record
◀ Back
Soft+
Soft
Normal
Vivid
Vivid+
OK Set
You can select your preferred Auto Focus type according to the shooting
conditions.
[Center AF] : The rectangular area in the center of
the LCD monitor will be focused
[Multi AF] : This camera selects all of available
AF point from the 9 AF points.
[Soft+]/ [Soft]
: The edges of the image are softened. This effect is suitable for
editing images on your PC.
[Normal]
: The edges of the image are sharp.
This is suitable for printing.
[Vivid]/ [Vivid+] : The edges of the image are emphasized.
The edges will appear sharp, but noise may occur in the
recorded image.
RECORDING
Sharpness
Contrast
Auto Focus
Voice Memo
Voice Record
◀ Back
[Center AF]
Center AF
Multi AF
OK Set
[Multi AF]
※ When the camera focuses on the subject, the auto focus frame turns to green.
When the camera doesn't focus on the subject, the auto focus frame turns to red.
Contrast
You can set the difference between bright part of the image and dark part of
the image.
[High] : The image contrast is high.
[Normal] : The contrast is normal.
[Low]
: The image contrast is more subtle.
RECORDING
Sharpness
Contrast
Auto Focus
Voice Memo
Voice Record
◀ Back
High
Normal
Low
OK Set
《51》
Voice Memo
You can add your voice-over to a stored still
image. (Max. 10 sec.)
Voice Recording
RECORDING
Sharpness
Contrast
Auto Focus
Voice Memo
Voice Record
◀
Back
Off
On
OK Set
Press the shutter button to record a voice.
- Press the shutter button once and voice is
recorded for as long as the available recording
time (max:10 hour) allows. The recording time
will be displayed on the LCD monitor. Voice will
still be recorded if the shutter button is released.
- If you wish to stop recording, press the shutter
button again.
- File type : *.wav
- If the voice memo indicator is displayed on the
LCD monitor, the setting is completed.
- Press the shutter button and take a picture.
The picture is stored on the memory card.
- Voice memo will be recorded for ten seconds
from the moment the picture is stored. In the
middle of the sound recording, pressing the
shutter button will stop the voice memo.
SH Stop
《52》
A voice can be recorded for as long as the
available recording time (Max. 10 hour) allows.
RECORDING
Sharpness
Contrast
Auto Focus
Voice Memo
Voice Record
Normal
Normal
Center AF
Off
Move
OK Set
SH REC
MENU Exit
[Voice recording mode]
Voice Recording
Recording the movie clip without voice
■ Pausing while recording a voice
Using this function, you can record your
favourite voice clips into a voice recording file
without having to create multiple voice
recording files.
You can record the movie without voice.
1. Press the Pause button (
) to pause
REC
SH Stop
recording.
[Pausing the voice recording]
2. Press the Pause button (
) again to
resume the recording.
3. If you wish to stop recording, press the shutter button again.
Select [Voice Mute] menu in the Movie clip mode.
(
) icon will appear on the LCD monitor.
Press the Shutter button and a movie will record
for as long as the memory capacity allows without
voice.
RECORDING
Voice Mute
◀ Back
Off
On
OK Set
● A distance of 40cm between you and the camera (microphone) is the
best distance to record sound.
● If the camera power is turned off while the voice recording is paused,
the voice recording is cancelled.
SCENE mode
Use the menu to easily configure optimal settings for a variety of shooting
situations.
Press the MENU button and select a desired
sub menu.
※ Refer to page 22 for more information.
RECORDING
Scene Mode
Auto Focus
Voice Memo
Voice Record
◀ Back
NIGHTSCENE
PORTRAIT
CHILDREN
LANDSCAPE
CLOSE UP
TEXT
OK Set
《53》
Sound menu
Sound (
In this mode, you can set up sound settings. You can use the setup menu in
all camera modes, except Voice Recording mode.
Volume
■The items indicated by
Mode
Menu
are default settings.
Sub Menu
Available Mode
Page
Off
Volume
Low
Medium
)
You can set select a volume of start up sound, shutter sound, beep sound
and AF sound.
- [Volume] sub menu : [Off], [Low], [Medium], [High]
p.54
SOUND
Volume
Start Sound
Shutter Sound
Beep Sound
AF Sound
◀
Back
Off
Low
Medium
High
OK Set
High
Start up sound
Off
Start Sound
Sound 1
Sound 2
p.54
Sound 3
Off
(SOUND)
Shutter Sound
Sound 1
Sound 2
p.54
You can select the sound that is activated whenever the camera is turned on.
- Start up sound : [Off], [Sound 1], [Sound 2],
[Sound 3]
- If the start up image is set to [Off], the start up
sound will not activate, even though you may have
set these to on.
◀
Sound 3
Off
Beep Sound
Sound 1
Sound 2
p.55
SOUND
Volume
Start Sound
Shutter Sound
Beep Sound
AF Sound
◀
《54》
Off
Sound 1
Sound 2
Sound 3
OK Set
You can select the shutter sound.
- Shutter sound : [Off], [Sound 1], [Sound 2],
[Sound 3]
Off
On
Back
Shutter sound
p.55
Sound 3
AF Sound
SOUND
Volume
Start Sound
Shutter Sound
Beep Sound
AF Sound
Back
Off
Sound 1
Sound 2
Sound 3
OK Set
Sound (
)
Setup menu
Beep Sound
If you set sound to ON, various sounds will be activated for camera startup,
when buttons are pressed, so that you can be aware of the camera operation
status.
- [Beep Sound] sub menu : [Off], [Sound 1, 2, 3]
SOUND
Volume
Start Sound
Shutter Sound
Beep Sound
AF Sound
◀
Back
In this mode, you can set up basic settings. You can use the setup menu in all
camera modes, except Voice Recording mode.
■The items indicated by
Menu tab
Sub menu
Main menu
File
Off
Sound 1
Sound 2
Sound 3
OK Set
are default settings.
Reset
ENGLISH
Language
AF sound
If you set AF sound to ON, AF sound will be activated when a subject is
focused so that you can be aware of the camera operation status.
SOUND
Volume
Start Sound
Shutter Sound
Beep Sound
AF Sound
◀
Back
Off
On
p.56
FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
PORTUGUÊS
DUTCH
DANSK
SVENSKA
SUOMI
p.57
BAHASA
POLSKI
- [AF sound] sub menu : [Off], [On]
Page
Series
(Setup
menu 1)
Date&Time
OK Set
World Time
Magyar
yy/mm/dd
mm/dd/yy
dd/mm/yy
Off
London
Rome, Paris, Berlin
Athens, Helsinki
Moscow
Teheran
Abu Dhabi
Kabul
Tashkent
Mumbay, New Delhi
Kathmandu
Almaty
Yangon
Bankok, Jakarta
Beijing, Hong Kong
Seoul, Tokyo
Darwin, Adelaide
p.57
p.57
《55》
Setup menu
Menu tab
Imprint
LCD
AF Lamp
Start Image
(Setup
menu 2)
Sub menu
Main menu
World Time
(Setup
menu 1)
Setup menu 1 (
Okhotsk
Wellington, Auckland
Samoa, Midway
Honolulu, Hawaii
Alaska
LA, San Francisco
Denver, Phoenix
Chicago, Dallas
New York, Miami
Caracas, La Paz
Newfoundland
Buenos Aires
Mid-Atlantic
Cape Verde
-
Off
Date
Date&Time
-
Dark
Normal
Bright
-
Off
On
Off
Logo
User Image
-
File name
This function allows the user to select the file naming format.
[Reset]
p.57
p.58
p.58
p.58
p.58
Quick View
Off
0.5, 1, 3 sec
Power Off
Off
1, 3, 5, 10 min
p.59
LCD Save
Off
On
p.59
Video Out
NTSC
PAL
p.60
Format
No
Yes
p.61
Reset
No
Yes
p.61
※ Menus are subject to change without prior notice.
《56》
Page
Guam, Sydney
)
p.59
: After using the reset function, the next
file name will be set from 0001 even
after formatting, deleting all or inserting a
new memory card.
[Series] : New files are named using numbers that
follow the previous sequence, even
when a new memory card is used, or
after formatting, or after deleting all
pictures.
SETUP1
File
Language
Date&Time
World Time
Imprint
LCD
◀
Back
Reset
Series
OK Set
- The first stored folder name is 100SSCAM, and the first file name is ST830001.
- File names are assigned sequentially from ST830001 → ST830002
→ ~ → ST839999.
- The folder number is assigned sequentially from 100 to 999 as follows:
100SSCAM → 101SSCAM → ~ → 999SSCAM.
- Maximum numbers of files in a folder are 9999.
- The files used with the memory card conform to the DCF (Design rule for
Camera File systems) format. If you change the image file name, the image
may not play back.
Setup menu 1 (
)
LANGUAGE
World Time
There is a choice of languages that can be displayed on the LCD monitor.
Even if the battery is removed and inserted again, the language setting will be
preserved.
The date and time selected in the [Date&Time] serve as the date and time of
your present location. Setting [World Time] enables you to display the local
date and time on the LCD monitor when travelling overseas.
- LANGUAGE sub menu
: English, Korean, French, German, Spanish,
Italian, S.Chinese, T.Chinese, Russian,
Portuguese, Dutch, Danish, Swedish, Finnish,
Thai, Bahasa (Malay / Indonesian), Arabic,
Czech, Polish, Hungarian and Turkish.
SETUP1
File
Language
Date&Time
World Time
Imprint
LCD
◀
Back
ENGLISH
한국어
FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
OK Set
Setting up the Date / Time / Date type
- Available cities:
London, Cape Verde, Mid-Atlantic, Buenos Aires,
SETUP1
Newfoundland, Caracas, La Paz, New York,
Miami, Chicago, Dallas, Denver, Phoenix, LA, San
Francisco, Alaska, Honolulu, Hawaii, Samoa,
Seoul, Tokyo
Midway, Wellington, Auckland, Okhotsk, Guam,
[ GMT +9.00 ] 2007.06.01 09:51
OK Confirm
Sydney, Darwin, Adelaide, Seoul, Tokyo, Beijing,
Hong Kong, Bankok, Jakarta, Yangon, Almaty,
Kathmandu, Mumbai, New Delhi, Tashkent, Kabul, Abu Dhabi, Teheran,
Moscow, Athens, Helsinki, Rome, Paris, Berlin
You can change the date and time that will be displayed on the captured
images and set up the date type.
- Date type : [yy/mm/dd], [mm/dd/yy], [dd/mm/yy],
[Off]
SETUP1
File
Language
Date&Time
World Time
Imprint
LCD
◀
Back
07/06/01
13:00
yy/mm/dd
OK Set
《57》
)
Imprinting the recording date
Auto Focus lamp
There is an option to include DATE / TIME on still images.
You can turn on and off the Auto Focus lamp.
- Sub menus
[Off]
: The DATE & TIME will not be
imprinted on the image file.
[Date]
: Only the DATE will be imprinted
on the image file.
[Date&Time] : The DATE & TIME will be imprinted
on the image file.
SETUP1
File
Language
Date&Time
World Time
Imprint
LCD
◀
Back
Off
Date
Date&Time
OK Set
※ The Date & Time are imprinted at the bottom right side of the still image.
※ The imprint function is applied only to still images except for the images taken in
photo frame effect mode.
※ Depending on the manufacturer and print mode, the date printed on an image
may not be printed correctly.
LCD brightness
You can adjust the LCD brightness.
SETUP1
File
Language
Date&Time
World Time
Imprint
LCD
◀
《58》
Back
Dark
Normal
Bright
OK Set
SETUP1
Language
Date&Time
World Time
Imprint
LCD
AF Lamp
◀ Back
Off
On
OK Set
Start up image
You can select the image that is first displayed on the LCD monitor whenever
the camera is turned on.
- Sub menus : [Off], [LOGO], [User Image]
- Use a saved image for the start-up image with the
[Start Image] in the [RESIZE] menu in the play
mode.
- The start-up image will not be deleted by [Delete]
or [Format] menu.
- The User images will be deleted by [Reset] menu.
SETUP1
Date&Time
World Time
Imprint
LCD
AF Lamp
Start Image
◀ Back
Off
- Sub menus : [Dark], [Normal], [Bright]
- Sub menus
[Off] : The AF lamp will not light up in low light
conditions.
[On] : The AF lamp will light up in low light
conditions.
Setup menu 1 (
OK Set
Setup menu 2 (
)
Quick view
Auto power off
If you enable Quick View before capturing an image, you can view the image
you just captured on the LCD monitor for the duration set in the [Quick View]
setup. Quick view is possible only with still images.
This function switches the camera off after a set amount of time in order to
prevent unnecessary battery drainage.
- Sub menus
[Off]
- Sub menus
[Off]
: The quick view function can’t be
activated.
[0.5, 1, 3 sec] : The captured image is briefly
displayed during the selected time.
SETUP2
Quick View
Power Off
LCD Save
Video Out
Format
Reset
◀ Back
Off
0.5 sec
1 sec
3 sec
OK Set
: The power off function will not
SETUP2
Quick View
operate.
Power Off
Off
[1, 3, 5, 10 min] : The power will turn off
LCD Save
1 min
Video Out
3 min
automatically if not used for the
Format
5 min
Reset
10 min
period of time specified.
OK Set
◀ Back
- After replacing the battery, the power off setting will
be preserved.
- Note that the automatic power off function will not operate if the camera is in the
PC / Printer mode, slide show, playing back a voice recording and playing back
a movie clip.
LCD save
If you set the [LCD save] to On and the camera isn't operated during the
specified time, the LCD monitor will be turned off automatically.
- Sub menus
[Off] : The LCD monitor will not be turned off.
[On] : If the camera isn't operated during the
specified time (about 30 SEC.), the camera
power will be idle (Camera status
lamp:Blinking) automatically.
SETUP2
Quick View
Power Off
LCD Save
Video Out
Format
Reset
◀ Back
Off
On
OK Set
《59》
Setup menu 2 (
)
Selecting Video out type
- NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico.
The Movie output signal from the camera can be NTSC or PAL.
Your choice of output will be governed by the type of device (monitor or TV,
etc.) to which the camera is connected. PAL mode can support only BDGHI.
- PAL
: Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K.,
Holland, Italy, Kuwait, Malaysia, New Zealand, Singapore, Spain,
Sweden, Switzerland, Thailand, Norway.
- When using a TV as an external monitor, you will need to select the external or
AV channel of the TV.
■ Connecting to an external monitor
When the camera is connected to an external
monitor, the image and menus on the LCD monitor
will be visible on the external monitor and the LCD
monitor of the camera.
- There will be a digital noise on the external monitor, but it is not a malfunction.
SETUP2
Quick View
Power Off
LCD Save
Video Out
Format
Reset
◀ Back
NTSC
PAL
OK Set
- If the image is not in the centre of the screen, use the TV controls to centre it.
- When the camera is connected to an external monitor, some parts of the image
may not be displayed.
- When the camera is connected to an external monitor, the menu will be visible
on the external monitor and the menu functions are the same as those
indicated on the LCD monitor.
- When the camera is connected to an external monitor, the button sound may
not function.
Yellow - Video
White - sound
《60》
Setup menu 2 (
)
Formatting a memory
Initialisation
This is used for formatting the memory. If you run [Format] on the memory, all
images, including the protected images, will be deleted. Be sure to download
important images to your PC before formatting the memory.
All camera menu and function settings will be restored to their default values.
However, values for DATE / TIME, LANGUAGE, and VIDEO OUT will not be
changed.
- Sub menus
[No] : The memory will not be formatted.
[Yes]: A window for confirming the selection
displays. Select the [Yes] menu. A
[Processing!] message appears and the
memory will be formatted. If you run
FORMAT in Play mode, a [No Image!]
message will appear.
SETUP2
Quick View
Power Off
LCD Save
Video Out
Format
Reset
◀ Back
No
Yes
- Sub menus
[No] : Settings will not be restored to their defaults.
[Yes]: A window for confirm the selection displays.
Select the [Yes] menu and all settings will
be restored to their defaults.
SETUP2
Quick View
Power Off
LCD Save
Video Out
Format
Reset
◀ Back
No
Yes
OK Set
OK Set
■ Be sure to run [Format] on the following types of memory card.
- A new memory card, or an unformatted memory card
- A memory card that has a file this camera can't recognise or one that has been
taken from another camera.
- Always format the memory card using this camera. If you insert a memory card
that has been formatted using other cameras, memory card readers, or PCs,
you will get a [Card Error!] message.
《61》
Starting play mode
Turn the camera on and select Play mode by pressing the play mode button
(
). The camera can now play back the images stored in the memory.
If the memory card is inserted in the camera, all the camera functions apply
only to the memory card.
If the memory card is not inserted in the camera, all the camera functions
apply only to the internal memory.
Playing back a still image
1. Select the PLAY mode by pressing the
play mode button (
).
2. The last image stored on the memory is
displayed on the LCD monitor.
3. Select an image that you want to view by
pressing the Left/ Right button.
※ Press and hold the Left or Right button to
play back the images quickly.
《62》
Playing back a movie clip
1. Select the recorded movie clip that you want to
play back by using the Left/Right button.
2. Press the play & pause button (
) to play
back a movie clip file.
- To pause a movie clip file while playing it
back, press the play & pause button again.
- Pressing the play & pause button again will
cause the movie clip file to restart.
- To rewind the movie clip while it is playing,
press the Left button. To fast forward the
movie clip, press the Right button.
- To stop playback of the movie clip, press the
play & pause button, and then press the Left
or Right button.
/
Play
E
Capture
Starting play mode
Movie clip capture function
On camera movie trimming
You can capture still images from the movie clip.
You can extract desired frames of movie clip during the movie clip play back.
If the running time is under 10 seconds, the movie clip can’t be trimmed.
■ How to capture the movie clip
1. Press the Play / Pause button while playing the
movie clip. Then press the E button.
2. The paused movie clip is saved in a new file
name.
※ The captured movie clip file is the same size as
the original movie clip (800x592, 720x480,
640x480, 320x240).
※ When you press the E button at the beginning
of the movie clip, the first frame of the movie
clip will be saved as a still image.
T
Trim
E
Capture
[Paused]
[Press the E button]
1. Press the Pause button at the point of the movie
clip where you want to start extracting.
2. Press the T button.
3. Press the Play & Pause button and the
extracted range will be displayed on the status
bar.
4. Press the Play & Pause button once more at
the point where you wish the extracted file to
stop.
5. Press the T button and a confirmation window
will be displayed.
6. Select a desired sub menu by pressing the
Up/Down button and press the OK button.
[No]
: The movie trimming will be cancelled.
[Yes] : The extracted frames are saved as a
new file name.
T Trim
E Capture
T
Trim
Trimming?
No
Yes
OK Confirm
● If you don't specify the ending point of the movie clip, the trimming
confirmation window will be displayed at the point of the last frame.
《63》
Starting play mode
Playing back a recorded voice
1. Select the recorded voice that you want to play
back by using the Left/Right button.
2. Press the play & pause button (
) to play
back a recorded voice file.
- To pause a recorded voice file, while playing
it back, press the play & pause button again.
Play
- To resume playback of the voice file, press
the play & pause button
- To rewind the voice file while it is playing, press the Left button.
To fast forward the voice file, press the Right button.
- To stop playback of the voice memo, press the play & pause button and
then press the MENU/OK button.
Playing back a voice memo
1. Select a still image that has the voice memo.
2. Press the play & pause button (
) to play
back the voice memo.
- To pause the voice memo, while playing it
back, press the play & pause button (
)
again.
- To resume playback of the voice memo,
press the play & pause button.
- To stop playback of the voice memo, press
the play & pause button and then press the
MENU/OK button.
REW
FF
Pause
OK Stop
《64》
Play
LCD monitor Indicator
Using the camera buttons to set the camera
The LCD monitor displays shooting information about the displayed image.
In Play mode, you can use the buttons on the camera to conveniently set up
the Play mode functions.
④
③
②
①
Thumbnail (
) button
You can view multiple pictures, enlarge a selected picture, and crop and save
a selected area of an image.
⑤
⑥
■ Thumbnail display
⑦
⑬
⑫
⑪
⑩
⑨
⑧
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
) / Enlargement (
Description
Battery
Folder name & File name
Memory card indicator
Playback mode
Voice Memo
Protect
DPOF
Recording date
Image size
Flash
Shutter speed
Aperture value
ISO
Icon
100-0010
2007/06/01
3264x2448 ~ 256X192
ON/OFF
15 ~ 1/2000
F3.5 ~ F8.0
50 ~ 1600
Page
p.15
p.56
p.62
p.84
p.85
p.85
p.57
p.45
p.29
p.49
p.49
p.47
1. While an image is displayed on full screen, press the
thumbnail button.
2. The thumbnail display will highlight the image that
had been showing at the time the thumbnail mode
was selected.
3. Press the 5 function button to move to a desired image.
4. To view an image separately, press the enlargement button.
Pressing the thumbnail
button (
)
Pressing the enlargement
button (
)
Highlighted image
[Highlighted image]
[ Thumbnail display mode ]
《65》
Thumbnail (
) / Enlargement (
■Image enlargement
1. Select an image that you want to enlarge and
press the enlargement button.
2. Different parts of the image can be viewed by
pressing the 5 function button.
3. Pressing the thumbnail button will zoom back to
the original full sized image.
- You can tell whether the image displayed is an
enlarged view by checking the image
enlargement indicator shown at the top left of
the LCD monitor. (If the image is not an
enlarged view, the indicator will not be
displayed.) You can also check the area of
enlargement.
- Movie clips and WAV files can’t be enlarged.
- If an image is enlarged, a loss of quality may occur.
) button
■ The maximum enlargement rate in proportion to the image size
Image size
Maximum
enlargement rate
X12.0
X11.3
X9.5
X9.0
X8.0
X4.0
■ Trimming : You can extract part of the image that you want and save it
separately.
1. Select an image that you want to enlarge and
press the enlargement button.
Press the MENU/OK button and a message will
Trimming?
No
be displayed.
Yes
2. Select a desired sub menu by pressing the
Up / Down button and press the OK button.
OK Confirm
- [No] : The trimming menu will disappear.
- [Yes] : The trimmed image will be saved as a new file name, and appear on
the LCD monitor.
※ If there is not enough memory space to save the trimmed image, the image
can’t be trimmed.
《66》
Info(
) / Up button
Play & Pause (
When the menu is displayed on the LCD monitor, the UP button operates as
a direction button.
When the menu is not displayed on the LCD monitor, pressing the Info button
will display image information on the LCD monitor.
Info (
Info (
) button
) button
Info (
) / Down button
In Play mode, the play & pause/ down button works as follows:
- If the menu is displayed
Press the DOWN button to move from the main menu to a sub menu, or to
move down the sub menu cursor.
- If a still image with a voice memo, a voice file, or a movie clip is playing
·In Stop mode
: Plays a still image with a voice memo, a voice file, or a
movie clip.
·During playback
: Temporarily stops playback.
·In Pause mode
: Resumes playback
) button
Play
[ Voice recording is stopped ]
Pause
[ Voice recording is playing ]
OK Stop
Play
[ Voice recording is paused ]
《67》
Left / Right / Menu / OK button
Delete (
LEFT / RIGHT / MENU / OK buttons activate the following.
This deletes images stored on the memory card.
- LEFT button
: While the menu is showing, the LEFT button operates as a
direction button. While the menu is not showing, press the
LEFT button to select the previous image.
- RIGHT button : While the menu is showing, the RIGHT button operates as a
direction button. While the menu is not showing, press the
RIGHT button to select the next image.
- MENU button : When you press the MENU button, the play mode menu will
be displayed on the LCD monitor. Pressing it again will return
the LCD to the initial display.
- OK button
: When the menu is displayed on the LCD monitor, the OK
button is used for confirming data that is changed by using the
5 function button.
) button
1. Select an image that you want to delete by pressing the Left / Right button
and press the DELETE ( ) button.
T Select
Delete?
Delete?
No
Yes
No
Yes
OK Confirm
[Single Image]
OK
Confirm
[Thumbnail Image]
2. To add images to delete, press the T button.
- Left/Right button : Selects images
- T button
: checks for deletion
- OK button
: confirm the selection
Prev T
Printer (
) button
When the camera is connected to a PictBridge printer, you can print images by
pressing the Printer button.
◀
▶
Print
《68》
OK
Menu
Select
Next
OK
Confirm
3. Select the submenu values by pressing the Up / Down button and then press
the OK button.
- If [No] is selected : cancels "Delete Image".
- If [Yes] is selected : deletes the selected images.
E (Effect) button : Resize
Change the resolution (size) of pictures taken. Select [Start image] to save an
image to be the start-up image.
1. Press the play mode button and press the E
button.
2. Press the Left / Right button and select the
[RESIZE] (
) menu tab.
3. Select a desired sub menu by pressing the Up /
Down button and press the OK button.
- The resized image will have a new file name. The [Start Image] image is stored
not on the memory card but on the internal memory.
Exit
3M
●
●
●
●
●
●
●
●
●
- If a new user image is saved, one of the two user images will be deleted in order.
- If the memory capacity is insufficient to store the resized image, a [Memory Full!]
message will appear on the LCD monitor and the resized image can't be stored.
1M
●
1M
5M
6M
E
(● : Selectable)
3M
7M
Move
5M
5M
- Only JPEG images can be resized. Movie clip (AVI), Voice recording (WAV) files
can’t be resized.
- You can change the resolution of only those files compressed in the JPEG 4:2:2
format.
RESIZE
■Image Resize Types
8M
- A large sized image can be resized to a smaller sized image, but not vice versa.
●
3M
1M
●
●
2M
1M
●
●
●
●
《69》
E (Effect) button : Rotating an image
E (Effect) button : Colour
You can rotate the stored images by various degrees.
It is possible to add colour effects to your images by using this button.
1. Press the play mode button and press the
E button.
2. Press the LEFT / RIGHT button and select the
[ROTATE] (
) menu tab.
3. Select a desired sub menu by pressing the UP /
DOWN button.
1. Press the play mode button and press the E button.
2. Select
menu tab by pressing the Left /
Right button.
ROTATE
Move
E
COLOR
Exit
Left 90°
Right 90°
OK
Set
E
OK
Back
[
: Right 90˚]
: Rotate picture in a
clock-wise direction
180°
Set
E
OK
Back
[
: Left 90˚]
: Rotate picture in a counterclock-wise direction
Horizontal
Set
E
Back
[
: 180˚]
: Rotate picture 180 degrees
Vertical
OK
Set
E
Back
OK
Set
E
Back
[
: Vertical]
: Rotate picture vertically
4. The changed image is saved as a new file name.
※ If you display the rotated image on the LCD monitor, empty spaces may
appear to the left and right of the image.
《70》
E
Exit
3. Select a desired sub menu by pressing the Up / Down button and press the
OK button.
: Captured images will be stored in black and white.
: Captured images will be stored in a sepia tone
(a gradient of yellowish brown colours).
: Captured images will be stored in a red tone.
: Captured images will be stored in a green tone.
: Captured images will be stored in a blue tone.
: Save the image in negative mode.
: Captured images will be stored in set RGB tone.
4. The changed image is saved as a new file name.
[
: Horizontal]
: Rotate picture horizontally
Move
E (Effect) button : Colour
E (Effect) button : Special Colour
1. Press the play mode button and press the E button.
2. Select (
) menu tab by pressing the Left/Right button.
■ Custom colour
You can change the R (Red), G (Green) and
B (Blue) values of the image.
Custom Color
Colour Filter
Move
: Select / setup the Custom
Colour
- Up / Down button : Selects R, G, B
- Left / Right button : Change the values
OK
Set
- OK button
With this menu, you can change the colour information of the image
(excluding Red, Blue, Green and Yellow) to Black and White.
1. Select
Custom Color
by pressing the Up/Down button.
SPECIAL COLOR
Move
OK
Color Filter
Set
Move
OK
Exit
OK Set
E
Back
2. Press the OK button and the image is saved as a new file name.
《71》
E (Effect) button : Special Colour
Colour mask
With this menu, you can select a part you want to highlight. The rest of the image will be in black and white.
SPECIAL COLOR
Color Mask
Select
and a mark for
selecting part will display.
Move
E
Press the OK button and you can set
the size and location of the part.
Exit
OK Set
E
Move
Back
OK Set
TW Size
W / T button :
Changing size of part
Move
Press the OK button twice and the colour
mask image will be saved as a new file
name.
OK Set
TW Size
Up/Down/Left/Right button:
Changing the location
[Final image]
Move
《72》
OK Set
TW Size
E (Effect) button : Image editing
Brightness control
1. Press the play back button and press the E button.
2. Select
menu tab by pressing the Left/Right button.
You can change the brightness of the image.
1. Select (
) by pressing the Up/Down button
and a bar for selecting the brightness will be
displayed.
2. Change the brightness by pressing the
Left/Right button.
3. Press the OK button and the image will be
saved as a new file name.
Red eye Removal
Red eye effect can be removed from the captured image.
1. Select (
) by pressing the Up/Down button
and press the OK button.
2. The [Proccessing!] message displays and the
image is saved as a new file name.
Red Eye Fix
OK
Set
E
Brightness
Move
OK
Set
OK
Set
Back
Contrast control
You can change the contrast of the image.
1. Select (
) by pressing the Up/Down button
and a bar for selecting the contrast will be
displayed.
2. Change the contrast by pressing the Left/Right
button.
3. Press the OK button and the image will be
saved as a new file name.
Contrast
Move
《73》
E (Effect) button : Image editing
Saturation control
You can change the saturation of the image.
1. Select (
) by pressing the Up/Down button
and a bar for selecting the saturation will be
displayed.
2. Change the saturation by pressing the
Left/Right button.
3. Press the OK button and the image will be
saved as a new file name.
Saturation
Move
OK
Set
Noise Effect
You can add noise to an image to add a more classic feel to your photo.
1. Select (
) by pressing the Up/Down button
and press the OK button.
2. The [Proccessing!] message displays and the
image is saved as a new file name.
Add Noise
OK
《74》
Set
E
Back
E (Effect) button : FUN
Cartoon
You can add a text box on the image to make the image cartoon like.
※ The cartoon image is saved as 1M image size.
Select a desired position by
pressing the
Up/Down/Left/Right button
and press the OK button.
Cartoon
FUN
Select Cartoon (
Move
)
Frame
EE Exit
OK
E Set
EE Back
Move
OK
E Set
Change the location of
the text box by pressing
the Left/Right button.
Press the OK button and
the image is saved. Press
the OK button again to
open a new image to save.
OK Select
Select a desired frame
by pressing the Left/Right
button and then press
the OK button
OK Search
Fn
E
Move
Delete
OK
E Set
Select an image by pressing the Up/Down/Left/Right
button and press the OK button.
Select the third image with the same procedure.
Press the OK button and the file is
saved as a new file name.
Select the position of image
and text box with the same
procedure.
Move
OK
E Set
OK Save
Fn
E Delete
《75》
E (Effect) button: FUN
■ Before saving the cartoon image, you can change the selected image.
Preset focus frames
You can make the subject stand out from its surroundings. The subject will be
sharp and in focus while making the rest out of focus.
1. Pressing the Fn button deletes the images in order.
2. Press the OK button and you can select images.
High Light
FUN
Pressing the Fn
button
OK Save
Fn
E Delete
Move
OK Search
3. After selecting desired images, press the OK button to save the image as a
new file name.
OK
E Set
Select a desired frame by pressing the Left/Right button and press the OK
button.
High Light
High Light
Range
OK
E
Set
[Range 1]
《76》
Range
EE Exit
Fn
E Delete
High Light
Range
OK
E
Set
[Range 2]
High Light
Range
OK
E
Set
[Range 3]
Range
OK
E
Set
[Range 4]
E (Effect) button: FUN
Composite image
■Moving and changing the focus frame
You can change the focus frame after selecting a Range menu.
1. Select a focus frame by pressing the Left/Right button and press the OK
button.
2. Move the location of the frame by pressing the Up/Down/Left/Right button.
3. Press the OK button and the file is saved as a new file name.
High Light
Range
Pressing the
OK button
OK
E Set
You can combine 2 - 4 different shots in a still image.
Move
Move
Composite
FUN
EE Exit
E Set
Composite OK
OK
E Save
[The frame is activated]
Pressing
Up/Down/Left/
Right
button
Pressing the
OK button
Press the OK button.
(You can select 2-4 composite images)
Move
OK
E Set
● If you press the Shutter and Play mode button, a capture mode is
executed.
● The composite image is saved as 1M image size.
Move
OK
E Save
[After changing the frame
position]
《77》
E (Effect) button: FUN
※ Selecting 2 composite shots
■ Before selecting the last composite image, you can change a part of
composite image.
1. During the composite image editing, press the Fn button.
2. A previous image will be deleted. Press the OK button and you can select a
new image. After selecting an image, press the Fn button again and the
image will be deleted again.
Pressing the
Up/Down/Left/Right button
Move
OK
E Set
Move
OK
E Set
[Changing the position]
Pressing the
OK button
Pressing the Fn button
OK Search
Fn
E Delete
[Before selecting the 3rd image]
Pressing the
OK button
OK Search
3. Press the OK button and you can select an image again.
OK Select
EE Back
OK Search
Fn
E Delete
[Selecting the second image]
Select an image by pressing the 5 function button
and press the OK button
Change the location of second image by
pressing the Up/Down/Left/Right button
button and press the OK button to save
the image.
Move
《78》
OK Save
Fn
E Delete
Fn
E Delete
[Moving backward to the 2nd image]
E (Effect) button: FUN
Photo Frame
You can add 9 types of frame-like borders to a still image you want to capture.
Date & Time information will not be printed on the stored image taken with
Photo Frame menu.
FUN
Photo Frame
Move
EE Exit
Frame
OK
E Set
Select a desired sub menu by pressing the Up/Down/Left/Right button.
- Press the E button and the frame will be canceled.
Press the OK button and the image is saved.
《79》
E (Effect) button : FUN
Setting up the play back function using the LCD monitor
Sticker
PLAY mode functions can be changed by using the LCD monitor.
In the PLAY mode, pressing the MENU button displays the menu on the LCD
monitor. The menus you can set up in Play mode are as follows. To capture
an image after setting up the play menu, press the PLAY mode button or
shutter button.
You can add various stickers to the image.
FUN
Sticker
Select (
Move
E
Menu Tab
)
Sticker
Exit
OK
Set
Select a desired sticker
by pressing the
Left/Right button and
press the OK button
Move
OK Save
Fn Add
Select a location of
sticker by pressing the
Up/Down/Left/Right
button
※ You can add additional stickers by pressing
the Fn button.
Press the OK button to store the image.
SLIDE
SHOW
(
)
Main Menu
Sub Menu
Secondary Menu
Page
Show
Play / Repeat Play
-
p.82
All
Date
Select
-
Images
Effect
OK Save
Fn Add
(
Delight
Music
Off / Music 1, 2, 3
-
Off
-
On
-
Protect
-
Select
-
All
No / Yes
Select
Unlock / Lock
All
)
Standard
DPOF
Copy To Card
《80》
Classic
1, 3, 5, 10 sec
Delete
PLAY
BACK
Basic
Rhythmic
Interval
Voice Memo
Move
Off
Memories
p.82
p.83
p.84
p.84
p.85
Select / All / Cancel
Index
No / Yes
Size
Select / All / Cancel
No
-
Yes
-
p.85-87
p.87
Setting up the play back function using the LCD monitor
This menu is available while the camera is connected to a PictBridge
supporting printer (direct connection to the camera, sold separately) with a
USB cable.
Menu tab
Main menu
Type
Menu tab
Main menu
Images
Size
Layout
Sub menu
Secondary menu
One Pic
-
All Pics
-
Auto
-
PostCard
-
Page
p.89
Quality
Sub menu
Secondary menu
Auto
-
Plain
-
Photo
-
FastPhoto
-
Auto
-
Draft
-
Normal
-
Card
-
Fine
-
4X6
-
Auto
-
L
-
2L
-
Letter
-
A4
-
A3
-
Auto
-
Full
-
1
-
2
-
4
-
8
-
9
-
16
-
Index
-
Date Print
File Name
p.90
Reset
Off
-
On
-
Auto
-
Off
-
On
-
No
-
Yes
-
Page
p.90
※ Menus are subject to change without prior notice.
《81》
Starting the slide show (
)
Images can be displayed continuously at pre-set intervals.
You can view the slide show by connecting the camera to an external monitor.
1. Press the play mode button and press the menu button.
2. Press the LEFT / RIGHT button and select the [SLIDE SHOW] menu tab.
Start the slide show
The slide show can start only in the [Show] menu.
1. Use the Up / Down buttons to select the [Show]
SLIDE SHOW
menu and press the Right button.
Show
Play
Image
Repeat Play
2. Select a desired sub menu by pressing the
Effect
Up / Down button.
Interval
Music
[Play]
: The slide show is closed after
OK Set
◀ Back
one cycle.
[Repeat Play] : The slide show is repeated until
cancelled.
3. Press the OK button and the slideshow will be started.
- To pause the slide shown while playing it back, press the play & pause
(
) button again.
- Pressing the play & pause(
) button again will cause the slide show
restart.
- To stop playback of the slide show, press the play & pause(
) button,
and then press the OK / Menu button.
《82》
Selecting Images
You can select image to view
1. Use the Up / Down buttons to select the [Image]
SLIDE SHOW
menu and press the Right button.
Show
Image
2. Select a desired sub menu by pressing the
Effect
Up / Down button.
Interval
Music
[All]
: All images saved in the Memory are
◀ Back
played back.
[Date] : Images taken in a specified date are
played back.
[Select] : You can select desired images to play back
3. Press the OK button and the settings are saved.
All
Date
Select
OK
Set
Starting the slide show (
)
Configure slide show effects
Setting play interval
Unique screen effects can be used for the slide show.
Set the slide show play interval.
1. Select the [Effect] sub menu by pressing the
UP / DOWN button and press the RIGHT
button.
2. Use the Up / Down button to select the type of
effect.
3. Press the OK button to confirm the setting.
SLIDE SHOW
Show
Image
Effect
Interval
Music
◀
Back
Off
Basic
Classic
Memories
Rhythmic
Deilght
OK Set
1. Select the [Interval] sub menu by pressing the
UP / DOWN button and press the RIGHT
button.
2. Use the Up / Down buttons to select the desired
interval.
3. Press the OK button to save the configuration.
SLIDE SHOW
Show
Image
Effect
Interval
Music
◀
Back
1 sec
3 sec
5 sec
10 sec
OK Set
● The loading time depends on the image size and quality.
● While the slide show is playing, only the first frame of a MOVIE file is
displayed.
● While the slide show is playing, the voice recording file will not display.
● The interval menu functions in the [Off], [Basic] and [Classic] menu
only.
Setting Background Music
Set the slide show music.
1. Select the [Music] sub menu by pressing the
UP / DOWN button and press the RIGHT
button.
2. Use the Up / Down buttons to select the desired
Music.
3. Press the OK button to save the configuration.
SLIDE SHOW
Show
Image
Effect
Interval
Music
◀
Back
Off
Music 1
Music 2
Music 3
OK Set
《83》
Playback (
)
Voice memo
Deleting images
You can add your voice to a stored still image.
This deletes images stored on the memory card.
PLAYBACK
Veice Memo
Delete
Protect
DPOF
Copy to Card
◀
Back
Off
끄기
On
OK
정지00:00:00
Set
[Voice memo menu]
SH REC
[Ready for recording]
정지00:00:05
SH
Stop
[Voice is recording]
- Press the shutter button to take a picture. The images are saved on the
memory. After saving the image, the voice is recording for 10 seconds.
- To stop the recording, press the shutter button.
1. Press the Up / Down button and select the
[Delete] menu tab. And then press the Right
button.
2. Select a desired sub menu by pressing the UP /
DOWN button and press the OK button.
[Select] : Selection window for an image to delete
is displayed.
- Up/ Down/ Left/ Right : Select an image
- Zoom T Button : Select the image for deletion.
( mark)
- OK Button : Press the OK button to display the
confirmation message. Select the
[Yes] menu and press the OK
button to delete marked images.
[All] : Displays confirmation window. Select the
[Yes] menu and press the OK button to
delete all unprotected images. If there aren’t
protected images, all the images are deleted
and a [No Image!] message will display.
3. After deletion, the screen will be changed to the
play mode screen.
PLAYBACK
Voice Memo
Delete
Protect
DPOF
Copy To Card
◀
Select
All
Back
OK
T
OK
Set
Select
Delete
Delete All?
No
Yes
OK
Confirm
● Of all the files stored in the memory card, the unprotected files in the
DCIM subfolder will be deleted. Remember that this will permanently
delete unprotected images. Important shots should be stored on a
computer before deletion takes place. The startup image is stored in
the camera's internal memory (i.e., not on the memory card) and it will
not be deleted even if you delete all files on the memory card.
《84》
Playback (
)
Protecting images
DPOF
This is used to protect specific shots from being accidentally erased (Lock).
It also unprotects images that have been previously protected (Unlock).
■DPOF(Digital Print Order Format) allows you to embed printing information on
your memory card’s MISC folder. Select the pictures to be printed and how many
prints to make.
1. Press the Up / Down button and select the
[Protect] menu tab. And then press the Right
button.
2. Select a desired sub menu by pressing the UP /
DOWN button and press the OK button.
[Select ] : Selection window for an image to be
protected / released is displayed.
- Up / Down / Left / Right : Select an image
- Zoom W / T Button : Protect / release the image
- OK button : Your changes will be saved and the
menu will disappear.
[All] : Protect / release all saved images
- If you protect an image, the protect icon will be
displayed on the LCD monitor.
(An unprotected image has no indicator)
- An image in LOCK mode will be protected from
the delete function or [Delete] functions, but will
NOT be protected from the [Format] function.
■The DPOF indicator will display on the LCD monitor when an image that has
DPOF information plays back. Images can then be printed on DPOF printers,
or at an increasing number of photo labs.
PLAYBACK
Viuce Memo
Delete
Protect
DPOF
Copy To Card
◀
Select
All
Back
W
OK
Set
Unlock
T
■This function is not available for Movie clips and Voice recording files.
■When the wide angle image is printed as a wide angle print, 8% of the left and
right side of the image may not be printed. Check that your printer can support
the wide angle image when you print the image. When you print the image at a
photo lab, request that the image is printed as a wide angle image. (Some photo
labs may not support the wide angle size print.)
OK Set
Protect All?
Unlock
Lock
OK
Confirm
《85》
Playback (
)
■ Standard
■ Index
This function allows you to embed printing quantity information on a stored
image.
1. Press the Up / Down button and select the
[DPOF] menu tab. And then press the Right
button.
2. Press the Right button again and [Standard] sub
menu will display.
3. Select a desired sub menu by pressing the Up /
Down button and press the OK button.
[Select] : Selection window for an image to print is
displayed.
- Up / Down / Left / Right : Select an image to print.
- Zoom W / T Button : Select the number of prints.
[All] : Configure number of prints for all pictures
except movie and voice files.
- W / T button : Select a number of prints
[Cancel] : Cancel the print setup.
4. Press the OK button to confirm the setting.
If an image carries DPOF instructions, the DPOF
indicator (
) will show.
PLAYBACK
Select
끄기
All
Cancel
Standard
Index
Size
◀
Back
W
OK
0 Images
OK
W
《86》
T
Set
0 Images
OK
Set
Set
T
Images (except for movie clips and voice file) are printed as index type.
1. Press the Up / Down button and select the
PLAYBACK
[DPOF] menu tab. And then press the Right
Standard
button.
Index
Size
2. Press the Right button again and [Index] sub
menu will dispaly.
3. Select a desired sub menu by pressing the UP /
◀ Back
DOWN button.
If [No] is selected : Cancel the index print
setting.
If [Yes] is selected : The image will be printed in index format.
4. Press the OK button to confirm the setting.
No
Yes
OK Set
Playback (
)
■ Print size
Copy To Card
You can specify the print size when printing images stored on the memory
card.
The [Size] menu is available only for DPOF 1.1 compatible printers.
1. Press the Up / Down button and select the
[DPOF] menu tab. And then press the Right
button.
2. Press the Right button agian and select the [Size]
sub menu will dispaly.
3. Select a desired sub menu by pressing the UP /
DOWN button and press the OK button.
[Select] : Selection window for an image to be
changed printed size is displayed.
- Up / Down / Left / Right : Select an image.
- Zoom W / T Button : Change the print size.
- OK button : Your changes will be saved and the
menu will disappear.
[All] : Change print size of all saved images.
- W / T button : Select a print size
- OK button : Confirm the changed setting.
[Cancel] : Cancel all of the print size settings.
※ DPOF [Size] secondary menu : Cancel, 3X5,
4X6, 5X7, 8X10
1. Select the [Copy To Card] menu tab by pressing
PLAYBACK
the Up / Down button. And then press the Right
Voice Memo
button.
Delete
Protect
2. Select a desired sub menu by pressing the UP/
DPOF
DOWN button and press the OK button.
Copy To Card No
Yes
- [No] : Cancels "Copy to Card".
OK Set
◀ Back
- [Yes] : All images, movie clips and voice
recording files saved in the internal
memory are copied to the memory card after the [Processing!]
message is displayed. After copying has been completed, the screen
will return to play mode.
PLAYBACK
Sandard
Index
Size
◀
Select
All
Cancel
Back
W
OK Set
Cancel
OK
W
T
Set
Cancel
OK
This enables you to copy image files, movie clips and voice recording files to
the memory card.
T
Set
● Depending on the manufacturer and print model, cancelling the
printing may take a little longer for the printer to process.
《87》
Playback (
)
● When this menu is selected without inserting a memory card, the [No
Card] message will be displayed.
● If there is not enough space available in the memory card to copy
saved images in the internal memory (19 MB), the [Copy To Card]
command will copy only some of the images and display [Memory
Full!] message. Then the system will return to the playback mode.
Please be sure to delete any unnecessary files to free up space before
inserting the memory card into the camera.
● When you move the images that are stored in the internal memory by
doing [Copy To Card] to the card, the next number of file names will be
created in the card to avoid duplication of the file name.
- When the [Reset] of the [File] setup menu is set : The copied file
names start from after the last stored file name.
- When the [Series] of the [File] setup menu is set : The copied file
names start from after the last captured file name. After completing
[Copy To Card], the last stored image of the last copied folder is
displayed on the LCD monitor.
《88》
PictBridge
You can use the USB cable to connect this camera to a printer that supports
PictBridge (sold separately) and print the stored images directly.
Movie clips and voice files cannot be printed.
■ Setting up the camera for connection to the printer
1. Connect the camera and printer with USB cable.
2. Select the [Printer] menu by pressing Up / Down
button and press the OK button.
Select USB
Computer
Printer
OK
■ Connecting the Camera to a Printer
Confirm
PictBridge
PictBridge : Picture Selection
※ If the [USB] menu is set to the [Computer], you cannot connect a Pictbridge
compatible printer to the camera through USB cable with [Connecting Computer]
message. In this case, remove the cable and do the step 1 and 2 again.
You can select images you want to print
■ Easy printing
When you connect the camera to printer in the
Play back mode, you can print a picture easily.
- Pressing the printer (
) button :
Currently displayed image will be printed with the
printer’s default setting.
- Pressing the Left / Right button :
Selects a previous / next image.
◀
▶
Print
OK Menu
■ Setting the Number of Copies to Print
1. Press the Menu button and the PictBridge menu
PICTBRIDGE
will display.
One Pic
Images
2. Use the Up / Down buttons to select the [Images] Size
All Pics
Layout
menu and press the Right button.
Type
3. Use the Up / Down buttons to select a desired
Quality
Date
sub menu and press the OK button.
◀ Back
OK Set
- Select [One Pic] or [All Pics]. A screen where
you can set the number of copies to print will appear as shown below.
⓪
⓪
Prev Next
SH Exit
OK Set
[When [One Pic] is selected]
SH Exit
OK Set
[When [All Pics] is selected]
- Press the Up / Down button to select the number of prints.
- When [One Pic] is selected : Use the Left / Right button to select another
picture. After selecting another picture, select
the number of prints for another picture.
- After setting the number of prints, press the OK button to save.
- Press the Shutter button to return to the menu without setting the number
of prints.
4. Press the Print button (
) and images will be printed.
《89》
PictBridge : Print Setting
PictBridge : Reset
You can select the Paper Size, Print Format, Paper Type, Print Quality, Date
Print, and File Name Print menus for printed pictures.
Initialises user-changed configurations.
1. Press the Menu button and the PictBridge menu
will display.
2. Use the Up / Down buttons to select the desired
menu, and then press the Right button.
3. Use the Up / Down buttons to select the desired
sub menu value, and then press the OK button.
Menu
Size
Function
Set the size of the printing
paper
PICTBRIDGE
Images
Size
Layout
Type
Quality
Date
◀ Back
Auto
PostCard
Card
4×6
L
2L
OK
Sub menu
Auto, PostCard, Card, 4X6, L,
2L, Letter, A4, A3
Set the number of pictures to
be printed on a sheet of paper
Auto, Full, 1, 2, 4, 8, 9, 16, Index
Type
Set the quality of the printing
paper
Auto, Plain, Photo, FastPhoto
Set the quality of the picture to
be printed
Auto, Draft, Normal, Fine
Date
File Name
Set whether to print the date
Auto, Off, On
Set whether to print the file name
Auto, Off, On
※ Some menu options are not supported on all printers.
If not supported, the menus are still displayed in the LCD, but are not selectable.
《90》
PICTBRIDGE
Layout
Type
Quality
Date
File Name
Reset
◀ Back
No
Yes
OK
Set
Set
Layout
Quality
1. Use the Up / Down buttons to select the [Reset]
menu tab. And then press the Right button.
2. Use the Up / Down buttons to select the desired
sub menu value, and then press the OK button.
If [Yes] is selected : All print and image settings
will be reset.
If [No] is selected : Settings will not be reset.
※ Default print setting varies depending on the printer manufacturer.
For your printer’s default setting, refer to the user’s guide that came with your
printer.
Important notes
Be sure to observe the following precautions!
● This unit contains precision electronic components. Do not use or store this
unit in the following locations.
- Areas exposed to severe changes in temperature and humidity.
- Areas exposed to dust and dirt.
- Areas exposed to direct sunlight or the inside of a vehicle in hot weather.
- Environments where there is high magnetism or excessive vibration.
- Areas with high explosives or highly flammable materials.
● Do not leave this camera in places subject to dust, chemicals (like
naphthalene and mothballs), high temperature and high humidity.
Keep this camera with silica gel in a hermetically sealed box when not
planning to use the camera for a long period of time
● Sand can be particularly troublesome to cameras.
- Do not let sand get inside the camera when using it on beaches, coastal
dunes, or other areas where there is lots of sand.
- Doing so may result in failure or may permanently render the camera unusable.
● Handling the camera
● Extremes in temperature may cause problems.
- If the camera is transferred from a cold to a warm and humid
environment, condensation can form on the delicate electronic circuitry. If
this occurs, turn the camera off and wait for at least 1 hour until all
moisture is dispersed. Moisture built up can also occur on the memory
card. If this happens, turn off the camera and remove the memory card.
Wait until the moisture has dispersed.
● Caution on Using the Lens
- If the lens is subjected to direct sunlight, it could result in the discoloration
and deterioration of the image sensor.
- Take care not to get fingerprints or foreign substances on the surface of the
lens.
● If the digital camera is not used for a long period, an electric discharge can
occur.
It is a good idea to remove the battery and the memory card if you do not
intend using the camera for an extended period of time.
● If the camera is exposed to an electronic interference, it will turn itself off to
protect the memory card.
- Never drop the camera or subject it to severe shocks or vibrations.
- Protect the large size LCD monitor from an impact. When this camera is not
used, keep it in the camera case.
- Avoid obstructing the lens or the flash when you capture an image.
- This camera is not waterproof.
To avoid dangerous electrical shocks, never hold or operate the camera with
wet hands.
- If you use this camera in wet places, such as beach or pool, do not let water or
sand get inside the camera. Doing so may result in failure or may permanently
damage the unit.
《91》
Important notes
Warning indicator
● Camera Maintenance
There are several warnings that may appear on the LCD display.
- Use a soft brush (available from photo stores) to gently clean the lens and LCD
assemblies. If this does not work, lens-cleaning paper with lens cleaning fluid
can be used.
Clean the camera body with a soft cloth. Do not allow this camera to come into
contact with solvent materials such as benzol, insecticide, thinners etc. This
may damage the body shell of the camera and also affect its performance.
Rough handling can damage the LCD monitor. Take care to avoid damage
and keep the camera in its protective carry case at all times when not in use.
● Do not attempt to disassemble or modify the camera.
● Under certain conditions, static electricity can cause the flash unit to fire. This is
not harmful to the camera and is not a malfunction.
● When images are uploaded or downloaded, the data transfer may be affected
by static electricity. In this case, disconnect and re-connect the USB cable
before trying the transfer again.
● Before an important event or going on a trip, you should check the camera
condition.
- Take a picture for testing the camera condition and prepare extra battery.
- Samsung cannot be held responsible for camera malfunctions.
《92》
[ Card Error ! ]
ㆍMemory card error
→ Turn off the camera power and turn it on again
→ Insert the memory card again
→ Insert and format the memory card (p.61)
[ Card Locked! ]
ㆍThe memory card is locked
→ SD/SDHC memory card : Slide the write protect switch to the top of the
memory card
[ No Card! ]
ㆍA memory card is not inserted
→ Insert the memory card again
→ Turn off the camera power and turn it on again
[ No Image! ]
ㆍThere are no images stored on the memory
→ Take images
→ Insert a memory card that is holding some images
Warning indicator
Before contacting a service centre
[ File Error! ]
Please check the following
ㆍFile error
→ Delete the file
ㆍMemory card error
→ Contact a camera service centre
[ Low Battery! ]
ㆍThere is low battery capacity
→ Insert fresh batteries.
[ Low Light! ]
ㆍWhen taking pictures in dark places
→ Take pictures in Flash Photography mode.
The camera doesn’t switch on
ㆍThere is low battery capacity
→ Insert fresh batteries. (p.15)
ㆍBattery is inserted incorrectly with the polarities reversed.
→ Insert the battery according to the polarity marks (+, -)
The camera power ceases while in use
ㆍThe battery is exhausted
→ Insert fresh batteries
ㆍThe Camera is turned off automatically
→ Turn on the camera power again.
Battery power quickly drains
ㆍThe Camera is being used in low temperatures
→ Keep the camera in warm conditions (i.e. inside a coat or jacket) and only
remove it in order to take images
《93》
Before contacting a service centre
Camera does not take images when pressing the Shutter button
The flash does not fire
ㆍThere is insufficient memory capacity
→ Delete unnecessary image files
ㆍThe memory card has not been formatted
→ Format the memory card (p.61)
ㆍThe memory card is exhausted
→ Insert a new memory card
ㆍThe memory card is locked
→ Refer to [Card Locked!] error message
ㆍThe camera's power is off
→ Turn the camera power on
ㆍThe battery is exhausted
→ Insert fresh batteries (p.15)
ㆍBattery is inserted incorrectly with the polarities reversed.
→ Insert the battery according to the polarity marks (+, -)
ㆍFlash off mode has been selected
→ Dis-engage flash off mode
ㆍThe camera mode can't use the flash
→ Refer to the FLASH instruction (p.29)
Incorrect date and time is displayed
ㆍThe date and time have been set incorrectly or the camera has adopted the
default settings
→Reset the date and time correctly
The camera buttons do not operate
ㆍCamera malfunction
→ Remove/re-insert battery and switch the camera on
A card error has occurred while the memory card is in the camera.
The camera suddenly stops working while in use
ㆍThe camera stopped due to a malfunction
→ Remove /re-insert battery and switch the camera on
ㆍIncorrect memory card format
→ Re-format the memory card
The images don't play back
The images are unclear
ㆍA picture was taken the subject without setting an appropriate macro mode
→ Select an appropriate macro mode to take a clear image.
ㆍTaking a picture beyond the flash range
→ Take a picture within the flash range
ㆍThe lens is smudged or dirty
→ Clean the lens
《94》
ㆍIncorrect file name (Violation of DCF format)
→ Do not change the image file name
Colour of image is different to the original scene
ㆍWhite balance or effect setting is incorrect
→ Select appropriate White balance and effect
Before contacting a service centre
Specifications
Images are too bright
Image Sensor
ㆍExposure is excessive
→ Reset exposure compensation
No image on external monitor
- Type : 1/2.5" CCD
- Effective Pixel : Approx. 8.2 Mega-pixel
- Total Pixel : Approx. 8.3 Mega-pixel
Lens
- Focal Length : NV Lens f = 6.3 ~ 18.9mm (35mm film
ㆍThe external monitor has not been connected properly with the camera
→ Check the connection cables
ㆍThere are incorrect files in the memory card
→ Insert a memory card that has correct files
equivalent : 38 ~ 114mm)
- F No. : F3.5 ~ F4.5
- Digital Zoom :·Still Image mode : 1.0X ~ 5.0X
·Play mode : 1.0X ~ 12.0X
When using the PC’s explorer, the [Removable Disk] file does not show
ㆍCable connection is incorrect
→ Check the connection
ㆍThe camera is off
→ Turn the camera on
ㆍThe operating system is not Windows 98SE, 2000, ME, XP, Vista / Mac OS 10.0
- 10.4. Alternatively the PC does not support USB
→ Install Windows 98SE, 2000, ME, XP, Vista / Mac OS 10.0 - 10.4 to PC that
supports USB
ㆍThe camera driver is not installed
→ Install a [USB Storage Driver]
(depends on image size)
LCD Monitor
- 2.5" color TFT LCD (230,000 dots)
Focusing
- Type : TTL auto focus, Multi-AF, Face Recognition AF,
Manual Focus
- Range
Normal
Wide
Tele
80cm ~ Infinity
Macro
Super Macro
Auto Macro
5cm ~ 80cm
1cm ~ 5cm
5cm ~ Infinity
40cm ~ 80cm
-
40cm ~ Infinity
Shutter
- Speed 1 ~ 1/2,000 sec. (Night : 15 ~ 1/2,000 sec.)
Exposure
- Control : Program AE
- Metering : Multi, Spot, Center-weighted, Face Recognition
- Compensation : ±2EV (1/3EV steps)
- ISO : Auto, 50, 100, 200, 400, 800, 1600
《95》
Specifications
Flash
- Modes : Auto, Auto & Red-eye reduction, Fill-in flash,
- Movie Clip
·With Audio or without Audio
Slow sync, Flash off, Red-eye Fix
- Range : Wide : 0.2m ~ 3.0m, Tele : 0.5m ~ 2.5m
(recording time : memory capacity dependent)
- Recharging Time : Approx. 4 sec
·Size : 800x592, 720x480, 640x480, 320x240
Sharpness
- Soft+, Soft, Normal, Vivid, Vivid+
·Frame rate : 30 fps, 20 fps, 15 fps
Color Effect
- Normal, B&W, Sepia, Red, Blue, Green, Negative,
·Optical Zoom up to 3.0X
(15/20 fps for 800x592, 720x480)
Custom Color
White Balance
(Voice Recording On during Optical zoom usage)
·Movie stabilizer(User selectable)
- Auto, Daylight, Cloudy, Fluorescent_H, Fluorescent_L,
·Movie Editing (Embedded) : Pause during recording,
Tungsten, Custom
Still Image Capture
Voice Recording - Voice Recording (max. 10 hours)
- Voice Memo in Still Image (max. 10 sec.)
Date Imprinting
- Date, Date & Time, Off (user selectable)
Shooting
- Still Image
Storage
- Media
·Internal memory : 19MB flash memory
·External Memory (Optional)
: MMC plus (up to 2GB guaranteed)
·Mode : Auto, Program, ASR, Scene
·Scene : Night, Portrait, Children, Landscape, Close-up,
Text, Sunset, Dawn, Backlight, Fireworks,
SD/SDHC (up to 4GB guaranteed)
- File Format
·Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1,
Beach & Snow, Cafe, Food, Self Shot
(Total 14 modes)
·Shooting : Single, Continuous, AEB, Interval Shooting,
Motion Capture
PictBridge 1.0
·Movie Clip : AVI (MPEG-4)
·Audio : WAV
- Image Size
·Self-timer : 2 sec., 10 sec., Double, Motion Timer
3264x2448 3264x2176 3264x1824 2592x1944 2048x1536 1024x768
《96》
Specifications
- Capacity (256 MB Size)
Weight
- 110g (without batteries and card)
Operating Temperature
Super Fine
57
68
84
93
172
558
Fine
103
115
134
158
265
663
Normal
180
206
233
271
425
742
※ These figures are measured under Samsung standard conditions and may
- 0 ~ 40°C
Operating Humidity
- 5 ~ 85%
Software
- Samsung Master, Adobe Reader
vary depending on shooting conditions and camera settings.
“E”
”Button
- Effect : Color, Image Adjust, Special Colour,
Fun ( Highlight, Composite, Photo Frame, Cartoon)
※ Specifications are subject to change without prior notice.
※ All trademarks are the property of their respective owners.
- Editing : Resize, Rotate, Color, Special Color, Image Adjust
(Brightness, Contrast ,Saturation ,Add Noise)
Fun (Cartoon , Highlight, Composite, Photo Frame,
Sticker)
Image Play
- Type : Single image, Thumbnails, Slide show, Movie Clip
Interface
- Digital output connector : USB 2.0 High Speed
- Audio : Mono
- Video output : NTSC, PAL (user selectable)
- DC Adapter : 4.2V (24-pin connector)
Power Source
- Rechargeable battery : SLB-0837(B), 3.7V (800mAh)
- Adaptor : SAC-45 (DC 4.2V, 450mA)
Dimensions (WxHxD)
- 93.3 X 18.0 X 57.7mm (excluding protrusions)
《97》
Software Notes
System Requirements
Please ensure that you read the instruction manual carefully before use.
- The attached software is a camera driver and image editing software tool for
Windows.
- Under no circumstances should all or part of either the software or the user
manual be reproduced.
- Copyrights for software are licensed only for use with a camera.
- In the unlikely event of a manufacturing fault, we will repair or exchange your
camera.
We cannot, however, be held responsible in any way for damage caused by
inappropriate use.
- Using a Hand-made PC or a PC and OS that has not been guaranteed by the
manufacturer is not covered by the Samsung warranty.
- Before reading this manual, you should have a basic knowledge of computers and
O/S (Operating Systems).
For Windows
For Macintosh
PC with processor better than
Pentium II 450MHz
Power Mac G3 or later
(Pentium 800MHz recommended)
Windows 98SE / 2000 / ME / XP/Vista
Mac OS 10.0 ~ 10.4
Minimum 128MB RAM
(Over 512MB recommended)
Minimum 64MB RAM
200MB of available hard disk space
110MB of available hard-disk space
(Over 1GB recommend)
USB port
USB port
CD-ROM drive
CD-ROM drive
1024x768 pixels, 16bit color display
compatible monitor
(24bit color display recommended)
MicroSoft DirectX 9.0C
《98》
MPlayer (For movie clip)
About the software
After inserting the CD-ROM provided with this camera into the CD-ROM drive,
the following window should automatically run.
Before connecting the camera to the PC,
you should first install the camera driver.
● Be sure to check the system requirements before installing the driver.
● You should allow 5 ~ 10 seconds for running the automatic setup
program according to the capability of your computer. If the frame does
not appear, run the [Windows Explorer] and select [Installer.exe] in the
CD-ROM Drive root directory.
■ Camera driver : This enables images to transfer between the camera
and PC.
This camera uses the USB Storage Driver as the camera driver. You can use
the camera as a USB card reader. After installing the driver and connecting this
camera to the PC, you can find [Removable Disk] in [Windows Explorer] or [My
computer]. A USB Storage Driver is provided only for Windows. A USB Driver
for MAC is not included with the Application CD. You can use the camera with
Mac OS 10.0~10.4.
■ Samsung Master : This is the all-in-one multi media software
solution.
You can download, view, edit and save your digital images and movie clips with
this software. This software is only compatible with Windows.
《99》
Setting up the application software
To use this camera with a PC, install the application software first.
After this has been done, the stored images in the camera can be moved to
the PC and can be edited by an image editing program.
■ You can visit the Samsung web-site through the internet.
http://www.samsungcamera.com : English
http://www.samsungcamera.co.kr : Korean
1. The auto run frame will display.
Click the [Install] menu in the Auto
run frame.
2. Install the camera driver, DirectX, XviD, Samsung Master and Adobe Reader
by selecting a button shown on the monitor. If a latest version of DirectX was
installed on your computer, DirectX may not be installed.
《100》
※ The XviD codec is distributed according to the GNU General Public License
and everyone can copy, distribute and change this codec. This License
applies to any program or other work which contains a notice placed by the
copyright holder saying it may be distributed under the terms of this General
Public License. For more information, see the License documents
(http://www.gnu.org/copyleft/gpl.html).
Setting up the application software
3. After restarting the computer, connect the PC to the camera with the USB
cable.
4. Turn the camera power on.
The [Found New Hardware Wizard] will
open and the computer will recognise the
camera.
※ If your OS is Windows XP/ Vista, an
image viewer program will open.
If the download window of Samsung
Master opens after starting Samsung
Master, the camera driver was set up
successfully.
《101》
Setting up the application software
● If you have installed the camera driver, the [Found New Hardware
Wizard] may not open.
● On a Windows 98SE system, the Found New Hardware Wizard dialog
box opens and a window asking you to select a driver file may appear.
In this case, specify "USB Driver" in the CD supplied.
● PDF documents of user manual are included in the Software CD-ROM
supplied with this camera. Search the PDF files with Windows
explorer.
Before opening the PDF files, you must install the Adobe Reader
included in the Software CD-ROM.
● To install the Adobe Reader 6.0.1 correctly, Internet Explorer 5.01 or
later has to be installed. Visit "www.microsoft.com" and upgrade the
Internet Explorer.
《102》
Starting PC mode
If you connect the USB cable to a USB port on your PC and then turn on the
power, the camera will automatically switch to "computer connection mode".
In this mode, you can download stored images to your PC through the USB
cable.
■ Camera settings for connection
1. Turn on the camera
2. Connect the camera and computer with the
supplied USB cable.
3. Turn on the computer. The camera and
computer are connected.
4. External device selection menu will display on
the LCD monitor.
5. Select the [Computer] by pressing the Up /
Down button and press the OK button.
Select USB
Computer
Printer
OK
Confirm
Starting PC mode
■ Connecting the camera to a PC
■ Downloading stored images
You can download the still images stored on the camera to your PC's hard disk
and print them or use a photo editing software to edit them.
1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display, select
[My computer] and double click [Removable
Disk → DCIM → 100SSCAM].
The image files will then be displayed.
※If you selected [Printer] in Step 5, when you connect the camera to your
computer, the [Connecting Printer] message will display and the connection
will not be established.
In this case, disconnect the USB cable, and then follow the procedure from
Step 2 and onward.
3. Select an image and press the right mouse
button.
■ Disconnecting the camera and PC
Refer to page 105 (Removing the removable disk).
《103》
Starting PC mode
4. A pop-up menu will open.
Click the [Cut] or [Copy] menu.
- [Cut] : cuts a selected file.
- [Copy] : copies files.
5. Click a folder where you want to paste the file.
6. Press the right mouse button and a pop-up
menu will open. Click [Paste].
7. An image file is transferred from the camera
to your PC.
《104》
- By using [Samsung Master], you can see the stored images in the memory
directly on the PC monitor and you can copy or move the image files.
● We recommend that you should copy the images to the PC to view
them. Opening images directly from the removable disk may be
subject to unexpected disconnection.
● When you upload a file that is not taken by this camera to the
Removable Disk, the [File Error!] message will be displayed on the
LCD monitor in the PLAY mode, and nothing is displayed in
THUMBNAIL mode.
Removing the removable disk
■ Windows 98SE
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has finished
blinking and is constantly on.
2. Unplug the USB cable.
■ Windows 2000/ME/XP/Vista
5. A [Safe to Remove Hardware] window will
open. Click the [OK] button.
6. A [Unplug or Eject Hardware] window will
open. Click the [Close] button and the
removable disk will be removed safely.
(The illustrations may differ from those shown depending on the Windows O/S.)
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has finished
blinking and is constantly on.
7. Unplug the USB cable.
2. Double-click the [Unplug or Eject Hardware]
icon on the task bar.
[Double-click!]
3. The [Unplug or Eject Hardware] window will
open. Select the [USB Mass Storage Device]
and click the [Stop] button.
4. The [Stop a Hardware device] window will
open. Select the [USB Mass Storage Device]
and click the [OK] button.
《105》
Setting up the USB Driver for MAC
1. A USB Driver for MAC is not included with the software CD as MAC OS
supports the camera driver.
2. Check the MAC OS version during start-up.
This camera is compatible with MAC OS 10.0 ~ 10.4.
3. Connect the camera to the Macintosh and turn the camera power on.
4. A new icon will be displayed on the desktop after connecting the camera to
the MAC.
Removing the USB Driver for Windows 98SE
To remove the USB driver, refer to the process shown below.
1. Connect the camera to your PC and turn them on.
2. Check whether the Removable Disk is on the [My Computer].
3. Remove the [Samsung Digital Camera] on the Device manager.
Using the USB Driver for MAC
1. Double click a new icon on the desktop and the folder in the memory will be
displayed.
2. Select an image file and copy or move it to MAC.
4. Disconnect the USB cable.
5. Remove the [Samsung USB Driver] on the Add/Remove Programs
Properties.
● For Mac OS 10.0 or later : First complete uploading from computer to
camera and then remove the removable
disk with the Extract command.
6. Uninstallation is complete.
《106》
Samsung Master
You can download, view, edit and save your images and movies with this
software. This software is only compatible with Windows.
To start the program, click [Start → Programs → Samsung → Samsung
Master → Samsung Master].
■ Downloading images
1. Connect the camera to your PC.
2. A window for downloading images will
display after connecting the camera to your
PC.
- To download the captured images, select
the [Select All] button.
- Select desired folder in the window and
click the [Select All] button. You can save
captured images and selected folder.
- If you click the [Cancel] button, downloading will be cancelled.
4. Select a destination and make a folder to
save downloaded images and folders.
- Folder names can be made in order of
date and images will be downloaded.
- Folder name will be made as you want
and images will be downloaded.
- After selecting a folder that was made
before, images will be downloaded.
5. Click [Next >] button.
6. A window will open as shown alongside.
The destination of the selected folder will
be displayed on the upper side of the
window.
Click the [Start] button to download the
images.
3. Click [Next >] button.
7. Downloaded images will be displayed.
《107》
Samsung Master
■ Image viewer : You can view the stored images.
■ Image edit : You can edit the still image.
①
⑥
⑤
①
④
⑦
②
③
④
②
③
- Image viewer functions are listed below.
① Menu bar : You can select menus.
File, Edit, View, Tools, Change functions, Auto download, help, etc.
② Image selection window : You can select the desired images in this window.
③ Media type selection menu : You can select image viewer, image edit and
movie edit functions in this menu.
④ Preview window : You can preview an image or a movie clip and check the
multi media information.
⑤ Zoom bar : You can change preview size.
⑥ Folder display window : You can see the folder location of the selected
image.
⑦ Image display window : Images of the selected folder are displayed.
※ Refer to the [Help] menu in Samsung Master for further information.
《108》
- Image edit functions are listed below.
① Edit menu : You can select the following menus.
[Tools] : You can resize or crop the selected image. See the [Help] menu.
[Adjust] : You can modify image quality. See the [Help] menu.
[Retouch] : You can change image or insert effects on the image.
See the [Help] menu.
② Drawing tools : Tools for editing an image.
③ Image display window : A selected image displays in this window.
④ Preview window : You can preview the changed image.
※ A still image edited with Samsung Master can’t be played back on the camera.
※ Refer to the [Help] menu in Samsung Master for further information.
Samsung Master
■ Movie edit : You can get the still image, movie clip, narration, music files
together in a movie clip.
※ Some movie clips that were compressed with a codec that is not compatible with
the Samsung Master can’t play back in the Samsung Master.
※ Refer to the [Help] menu in Samsung Master for further information.
①
②
- Movie clip edit functions are listed below.
① Edit menu : You can select the following menus.
[Add Media] : You can add other media elements to a movie.
[Edit Clip]
: You can change the brightness, contrast, colour and
saturation.
[Effects]
: You can insert an effect.
[Set Text]
: You can insert texts.
[Narrate]
: You can insert a narration.
[Produce]
: You can save the edited multi media as a new file name.
You can select AVI, Windows media (wmv) and Windows
media (asf) file types.
② Frame display window : You can insert multi media in this window.
《109》
FAQ
Please check the following if the USB connection malfunctions.
Case 1
USB cable is not connected or it is not the supplied USB cable.
→ Connect the supplied USB cable.
Case 2
The camera is not recognised by your PC.
Sometimes, the camera may appear under [Unknown Devices] in
Device Manager.
→ Install the camera driver correctly.
Turn off the camera, remove the USB cable, plug in the USB cable
again, and then turn on the camera.
Case 3
There is an unexpected error during file transfer.
→ Turn the camera power off and on again. Transfer the file again.
Case 4
When using the USB hub.
→ There may be a problem in connecting the camera to the PC through
the USB hub if the PC and the hub are not compatible. Wherever
possible, connect the camera to the PC directly.
Case 5
Are other USB cables connected to the PC?
→ The camera may malfunction when it is connected to the PC at the
same time as another USB cable. In this case, disconnect the other
USB cable, and connect only one USB cable to the camera.
《110》
Case 6
When I open the Device Manager (by clicking Start → (Settings) →
Control Panel → (Performance and Maintenance) → System →
(Hardware) → Device Manager), there are Unknown Devices or Other
Devices entries with a yellow question mark(?) beside them or devices
with an exclamation mark(!) beside them.
→ Right-click on the entry with the question (?) or exclamation (!) mark
and select "Remove". Restart the PC and connect the camera again.
For Windows 98SE PC, remove the camera driver also, restart the
PC, and then reinstall the camera driver.
Case 7
In some security programs (Norton Anti Virus, V3, etc.), the computer
may not recognise the camera as a removable disk.
→ Stop the security programs and connect the camera to the computer.
Refer to the security program instructions about how to temporarily
disable the program.
Case 8
The camera is connected to the USB port located on the front of the
computer.
→ When the camera is connected to the USB port located on the front of
the computer, the computer may not recognise the camera. Connect
the camera to the USB port located on the back of the computer.
FAQ
When the movie clip doesn’t play back on the PC
※ When the movie clip recorded by the camera doesn’t play back on the PC,
the causes are mostly due to the codec installed on the PC.
■ When codec for play back the movie clip isn’t installed
→ Install the codec as listed below.
[Installing codec for Windows]
1. Installing the XviD codec
1) Insert the CD provided with the camera.
2) Run the windows explorer and select [CD-ROM drive:\XviD] folder and
click the XviD-1.1.2-01112006.exe file.
※ The XviD codec is distributed according to the GNU General Public License
and everyone can copy, distribute and change this codec. This License
applies to any program or other work which contains a notice placed by the
copyright holder saying it may be distributed under the terms of this General
Public License. For more information, see the License documents
(http://www.gnu.org/copyleft/gpl.html).
[Installing codec for Mac OS]
1) Visit the following site for downloading the codec.
(http://www.divx.com/divx/mac)
2) Click the [Free Download] menu on the top right side of the window then
download windows appears.
3) Check the version of Mac OS and click the [Download] button to download
the file and save it on a desired folder.
4) Run the downloaded file and the codec for playing back the movie clip will
be installed.
※ If the movie file is not played back on the Macintosh OS, use a media
player that supports Xvid codec (e.g: Mplayer).
■ When the DirectX 9.0 or later is not installed
→ Install the DirectX 9.0 or later
1) Insert the CD provided with the camera
2) Run the windows explorer and select the [CD-ROM drive:\ USB
Driver\DirectX 9.0] folder and click the DXESETUP.exe file.
The DirectX will be installed. Visit the following site for downloading the
DirectX.http://www.microsoft.com/directx
■ If a PC (Windows 98SE) stops responding while the camera and PC are
connected repeatedly
→ If a PC (Windows 98SE) is turned on for a long time and the camera is
connected repeatedly, the PC may not recognise the camera.
In this case, re-start the PC.
■ If a PC connected with the camera stops responding while Windows is starting.
→ In this case, disconnect the PC and the camera and Windows will start.
If the problem happens continuously, set the Legacy USB Support to disable
and re-start the PC. The Legacy USB Support is in the BIOS setup menu.
(The BIOS setup menu differs from the PC manufacturers and some BIOS
menus don’t have Legacy USB Support) If you can’t change the menu by
yourself, contact to the PC manufacturer or BIOS manufacturer.
■ If the movie clip can’t be deleted, or the removable disk can’t be extracted or an
error message displays during the file transfer.
→ If you install only the Samsung Master, the problems mentioned above
occasionally happen.
- Close the Digimax Master program by clicking the Samsung Master icon on
the Taskbar.
- Install all the application programs included in the software CD.
《111》
Correct Disposal of This Product
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for
environmentally safe recycling. Business users should contact their supplier and
check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
FCC notice
■ NOTE :
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
■ CAUTION :
Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the
equipment.
Samsung Techwin cares for the environment at all product
manufacturing stages to preserve the environment, and is
taking a number of steps to provide customers with more
environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly
products, and indicates that the product satisfies the EU
RoHS Directive.
《112》
■ Declaration of Conformity
Trade Name
: SAMSUNG TECHWIN
Model No.
: SAMSUNG L83T
Responsible Party : Samsung Opto-Electronics America, INC.
Address
: 40 Seaview Dr. Secaucus,NJ 07094
Telephone No.
: 201-902-0347
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
SAMSUNG TECHWIN CO., LTD.
SAMSUNG OPTO-ELECTRONICS GmbH
OPTICS & DIGITAL IMAGING DIVISION
145-3, SANGDAEWON 1-DONG, JUNGWONGU,
SUNGNAM-CITY, KYUNGKI-DO, KOREA
462-121
TEL : (82) 31-740-8222, 8488, 8490
FAX : (82) 31-740-8398
www.samsungcamera.com
ZENTRALE, KEINE REPARATUR
AM KRONBERGER HANG 6
D-65824 SCHWALBACH/TS, GERMANY
TEL : 49 (0) 6196 66 5303
FAX : 49 (0) 6196 66 5366
TECHNISCHE SERVICE HOTLINE :
00800 4526 3727
(nur kostenfrei fur Anrufe aus Deutschland)
SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
1-800-SAMSUNG (726-7864)
www.samsungcamerausa.com
If you have any questions or comments relating to
Samsung cameras, Please contact
the SAMSUNG customer care center
Die Adressen Ihrer Kundendienste sowie die
Garantiebestimmungen entnehmen Sie bitte aus dem
beiliegenden Faltblatt (SAMSUNG INTERNATIONAL
WARRANTY CERTIFICATE)
INTERNET : www.samsungcameras.de
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD
SAMSUNG FRANCE S.A.S.
HOTLINE PHOTO NUMÉRIQUE :
00 800 22 26 37 27 (Numéro Vert-Appel Gratuit)
www.samsungphoto.fr
NO.9 ZHANGHENG STREET. MICRO-ELECTRONIC
INDUSTRIAL PARK JINGANG ROAD TIANJIN CHINA.
POST CODE : 300385
TEL : 800-810-5858
www.samsungcamera.com.cn
SAMSUNG OPTO-ELECTRONICS UK LIMITED
SAMSUNG HOUSE 1000 HILLSWOOD DRIVE
HILLSWOOD BUSINESS PARK
CHERTSEY KT16 OPS U.K.
TEL : 00800 12263727
(free for calls from UK only)
UK Service Hotline : 01932455320
www.samsungcamera.co.uk
RUSSIA INFORMATION CENTER
SAMSUNG ELECTRONICS
117545 ST. DOROZHNAYA BUILDING 3,
KORPUS 6, ENTRANCE 2, MOSCOW, RUSSIA
TEL : (7) 495-363-1700
CALL FREE : (8) 800 555 55 55 (from Russia only)
www.samsungcamera.ru
Internet address - http : //www.samsungcamera.com
The CE Mark is a Directive conformity
mark of the European Community (EC)
6806-4307
Download PDF

advertising