Samsung | SAMSUNG NV11 | Samsung NV11 User Manual

User Manual
Thank you for buying a Samsung camera.
This manual will guide you through using the camera, including
capturing images, downloading images and using the application software.
Please read this manual carefully before using your new camera.
ENGLISH
Instructions
Getting to know your camera
ƈ Use this camera in the following order.
Before connecting the camera to a PC, via
Set up the camera driver the USB cable, you will need to set up the
camera driver. Install the camera driver that
is contained in Application software CDROM. (p.73)
Take a picture
Take a picture. (p.18)
Insert the USB cable
Insert the supplied USB cable into the PC’s
USB port and the camera’s USB
connection terminal. (p.75)
Check the camera’s power
Check the camera’s power. If the power is
turned off, press the camera button to turn
it on.
Check [Removable Disk]
Open Windows EXPLORER and search
for [Removable Disk]. (p.76)
Thank you for buying a Samsung Digital Camera.
ƃ Prior to using this camera, please read the user manual thoroughly.
ƃ When you require After Sales service, please bring the camera and the cause of
the camera malfunction (such as battery, Memory card etc.) to the A/S centre.
ƃ Please check that the camera is operating properly before you intend to use it
(e.g. for a trip or an important event) to avoid disappointment. Samsung camera
takes no responsibility for any loss or damages that may result from camera
malfunction.
ƃ Keep this manual in a safe place.
ƃ If you use a card reader to copy the images on the memory card to your PC, the
images could be damaged. When transferring the images taken with the camera
to your PC, be sure to use the supplied USB cable to connect the camera to
your PC. Please note that the manufacturer accepts no responsibility for loss or
damage of images on the memory card due to the use of a card reader.
ƃ The contents and illustrations of this manual are subject to change without prior
notice for upgrading the camera functions.
ƃ If your camera was purchased outside of the country where you wish to have,
servicing fees are charged by the manufacturer's representatives in that country.
ƃ In some countries where this camera is not in market, servicings may not be
available.
Ҭ Microsoft, Windows and Windows logo are registered trademarks of Microsoft
Corporation incorporated in the United States and/or other countries.
Ҭ All brand and product names appearing in this manual are registered
trademarks of their respective companies.
ƃ If you use a card reader to copy the images on the memory card to your PC, the
images could be damaged. When transferring the images taken with the camera
to your PC, be sure to use the supplied USB cable to connect the camera to
your PC. Please note that the manufacturer accepts no responsibility for loss or
damage of images on the memory card due to the use of a card reader.
ŝ1Ş
Danger
Warning
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
ƈ Do not attempt to modify this camera in any way. To do so may result in fire,
injury, electric shock or severe damage to you or your camera. Internal
inspection, maintenance and repairs should only be carried out by your dealer or
Samsung Camera Service centre.
ƈ Please do not use this product in close proximity to flammable or explosive
gases, as this could increase the risk of explosion.
ƈ Should any form of liquid or a foreign object enter the camera, do not use it.
Switch off the camera, and then disconnect the power source. You must contact
your dealer or Samsung Camera Service centre. Do not continue to use the
camera as this may cause a fire or electric shock.
ƈ Do not insert or drop metallic or inflammable foreign objects into the camera
through access points e.g. the memory card slot and battery chamber. This may
cause a fire or electric shock.
ƈ Do not operate this camera with wet hands. This could pose a risk of electric
shock.
ƈ Do not use the flash in close proximity to people or animals. Positioning the flash
too close to your subject’s eyes may cause eyesight damage.
ƈ For safety reasons keep this product and accessories out of reach of children or
animals to prevent accidents e.g.:
ҮSwallowing battery or small camera accessories. If an accident should occur,
please consult a doctor immediately.
ҮThere is the possibility of injury from the camera’s moving parts.
ƈ Battery and camera may become hot during prolonged use and it may result in
camera malfunction. Should this be the case, let the camera sit idle for a few
minutes to allow it time to cool.
ƈ Do not leave this camera in places subject to extremely high temperatures, such
as a sealed vehicle, direct sunlight or other places of extreme variances in
temperature. Exposure to extreme temperatures may adversely affect the
camera’s internal components and could cause a fire.
ƈ When in use, do not cover the camera or Charger. This may cause heat to build
up and distort the camera body or cause a fire. Always use the camera and its
accessories in a well-ventilated area.
ŝ2Ş
Caution
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in a minor or moderate injury.
ƈ Leaking, overheating, or damaged battery could result in fire or injury.
ҮUse battery with the correct specification for the camera.
ҮDo not short circuit, heat or dispose of battery in fire.
ҮDo not insert the battery with the polarities reversed.
ƈ Remove the battery when not planning to use the camera for a long period of
time. Otherwise the battery may leak corrosive electrolyte and permanently
damage the camera’s components.
ƈ Do not fire the flash while it is in contact with hands or objects. Do not touch the
flash after using it continuously. It may cause burns.
ƈ Do not move the camera while it is switched on when you are using the AC
Charger. After use, always switch off the camera before unplugging the cable
from the wall socket. Then make sure that any connector cords or cables to
other devices are disconnected before moving the camera. Failure to do so may
damage the cords or cables and cause a fire or electric shock.
ƈ Take care not to touch the lens or lens cover to avoid taking an unclear image
and possibly causing camera malfunction.
ƈ Avoid obstructing the lens or the flash when you capture an image.
ƈ Before inserting any cables or AC adapter, check the directions and do not insert
by force. It may cause breakage of cable or camera.
ƈ Credit cards may be demagnetized if left near a camera case. Avoid leaving
magnetic strip cards near the case.
Contents
ƈHow to use the AUTO mode ōō18
READY
ƈHow to use the PROGRAM modeō18
ƃSystem chart ōōōōōōōōō5
ƈHow to use the ASM mode
ƃIdentification of features ōōōōō6
ƈHow to use the APERTURE
ƈFront & Topōōōōōōōōōō6
ƈBack & Bottom ōōōōōōōō7
ƈBottomōōōōōōōōōōōō8
18
PRIORITY mode
19
ƈHow to use the SHUTTER
PRIORITY mode
19
ƈSelf-timer lamp ōōōōōōōō8
ƈHow to use the MANUAL modeō19
ƈCamera Status Lamp ōōōōō8
ƈHow to use the ASR (Advanced
ƈMode dial ōōōōōōōōōō9
Shake Reduction) mode ōōōō20
ƈMode iconōōōōōōōōōō10
ƈHow to use the SPECIAL EFFECT modeō20
ƃConnecting to a Power Source ō10
ƈHow to use the SCENE mode ō20
ƈHow to charge the rechargeable
ƈHow to use the MOVIE CLIP modeō21
battery (SLB-1137D) ōōōōō12
ƃInserting the memory card ōōō13
ƃInstructions on using the memory cardō13
ƈTo record a movie clip without voiceō21
ƈPausing while recording a movie clip
(Successive Recording)ōōōōō21
ƈUsing Successive Recording ōō21
ƃThings to Watch Out for When
RECORDING
Taking Pictures ōōōōōōōō22
ƃWhen Using the Camera for the First
Time : Smart button
15
ƃUsing the camera buttons to set
the camera ōōōōōōōōō23
ƃWhen Using the Camera for the First
ƈPOWER button ōōōōōōō23
Time : Setting up the Date / Time and
ƈShutter button ōōōōōōōō23
Language ōōōōōōōōōō16
ƈZOOM W / T buttonōōōōōō24
ƃLCD monitor indicator ōōōōō17
ƃFace recognition(FR) button ōō25
ƃStarting the recording mode ōō18
ŝ3Ş
Contents
ƃUsing the LCD monitor to set the
PLAY
camera ōōōōōōōōōōō26
ƈEffectōōōōōōōōōōōō54
ƈInitialisation ōōōōōōōōō65
ƈMotion GIF ōōōōōōōōō55
ƃImportant notesōōōōōōōō66
ƈColor toneōōōōōōōōōō27
ƃStarting play mode ōōōōōō44
ƈRed eye fix ōōōōōōōōō55
ƃWarning indicator ōōōōōōō67
ƈBrightnessōōōōōōōōōō28
ƈPlaying back a still image ōōō44
ƈPictBridge ōōōōōōōōōō56
ƃBefore contacting a service centreō68
ƈSelecting focus type ōōōōō28
ƈPlaying back a movie clip ōōō44
ƈFlash ōōōōōōōōōōōō30
ƈMovie clip capture function ōōō45
ƈSize ōōōōōōōōōōōō31
ƈOn camera movie trimming ōō45
ƈContinuous shot ōōōōōōō32
ƈPlaying back a recorded voice ō45
ƃSetup menu ōōōōōōōōō58
ƈMetering ōōōōōōōōōō32
ƈPlaying back a recorded
ƃSpecifications ōōōōōōōō70
SETUP
SOFTWARE
ƈOSD set ōōōōōōōōōō60
ƃSoftware Notes ōōōōōōōō72
ƈSharpness ōōōōōōōōō33
voice memo ōōōōōōōōō46
ƈFile name ōōōōōōōōōō60
ƃSystem Requirements ōōōōō72
ƈEffectōōōōōōōōōōōō33
ƃLCD monitor indicator ōōōōō46
ƈLanguage ōōōōōōōōōō61
ƃAbout the software ōōōōōō72
ƈQuality / Frame rateōōōōōō34
ƃUsing the camera buttons to adjust
ƈSetting up the Date / Time / Date type ō61
ƃSetting up the application software ō73
ƈSelf-timer / Remote control ōōō34
the camera ōōōōōōōōō47
ƈImprinting the recording date ōō61
ƃStarting PC mode ōōōōōōō75
ƈVoice recording / Voice memo ō35
ƈPlay mode buttonōōōōōōō47
ƈLCD brightness ōōōōōōō61
ƃRemoving the removable diskōō77
ƈExposure compensation ōōōō36
ƈBACK button ōōōōōōōō47
ƈAuto Focus lamp ōōōōōōō62
ƃSetting up the USB Driver for MACō78
ƈISO ōōōōōōōōōōōō36
ƈThumbnail / Enlargement button ō47
ƈAuto power off ōōōōōōōō62
ƃUsing the USB Driver for MAC ō78
ƈWhite balance ōōōōōōōō37
ƈStarting the slide show ōōōō48
ƈQuick view ōōōōōōōōō62
ƃRemoving the USB Driver for
ƈScene menuōōōōōōōōō38
ƈProtecting images ōōōōōō49
ƈStart up image ōōōōōōōō62
Windows 98SE ōōōōōōōō78
ƈSpecial Effect : Photo Frame ōō38
ƈDeleting images ōōōōōōō50
ƈSound Volume ōōōōōōōō63
ƃDigimax Masterōōōōōōōō79
ƈSpecial Effect : Motion GIF ōōō39
ƈDPOF ōōōōōōōōōōō50
ƈOperation Sound ōōōōōōō63
ƃDigimax Biz Reader ōōōōōō81
ƈSpecial Effect : Composite shooting ō39
ƈDPOF : STANDARD ōōōōō51
ƈStart up sound ōōōōōōōō63
ƃFAQ ōōōōōōōōōōōō84
ƈShutter Speed ōōōōōōōō40
ƈDPOF : Print sizeōōōōōōō51
ƈShutter sound ōōōōōōōō63
ƈAperture Valueōōōōōōōō41
ƈDPOF : Index ōōōōōōōō52
ƈFormatting a memory ōōōōō63
ƈPhoto Gallery modeōōōōōō41
ƈRotating an image ōōōōōō52
ƈDelete All ōōōōōōōōōō64
ƈResize ōōōōōōōōōōō53
ƈCopy To Card ōōōōōōōō64
ƈTrimming ōōōōōōōōōō54
ƈSelecting Video out type ōōōō65
ŝ4Ş
System chart
Please check that you have the correct contents before using this product. The contents can vary depending on the sales region. To buy the optional equipment, contact
your nearest Samsung dealer or Samsung service centre.
< Included items >
Computer
(see p.75)
Camera case
User manual,
Product warranty
Camera strap
Software CD
(see p.72)
SD/SDHC memory card/
MMC (see p.14)
DPOF compatible
printer (see p.50)
Rechargeable battery
(SLB-1137D)
AV cable
Remote control
PictBridge compatible printer
(see p.56)
AC adapter (SAC-45) /
USB cable (SUC-C2)
External monitor
(see p.65)
ŝ5Ş
Identification of features
Front & Top
Mode dial
Shutter button
Power button
Self-timer lamp
Built-in flash
Remote control sensor
Auto focus lamp
Lens/ Lens cover
Microphone
ſ Instructions for the Built-in flash
- The flash opens automatically when you press
the shutter button down half way.
- Do not open the flash by force.
It may break the camera.
- Close the flash when you are not using it to
prevent breakage.
ŝ6Ş
Identification of features
Back & Bottom
Zoom W button (Thumbnail)
Zoom T button (Digital zoom)
Camera status lamp
LCD monitor
Smart button
Eyelet for camera strap
Smart button
BACK button / FR button
Play mode button
Tripod socket
USB / AV connection terminal
ŝ7Ş
Identification of features
ƈ Self-timer lamp
Bottom
Icon
Battery chamber cover
Status
Battery chamber
Blinking
Blinking
Blinking
Battery holder
Blinking
Description
- For the first 7 seconds, the lamp blinks at 1 second
intervals.
- For the final 3 seconds, the lamp blinks quickly at 0.25second intervals.
For 2 seconds, the lamp blinks quickly at 0.25-second
intervals before taking a picture
A picture will be taken after about 10 seconds and 2
seconds later a second picture will be taken.
Pressing the remote control shutter button will allow an
interval of 2 seconds before the image is taken.
Memory card slot
ƈ Camera Status Lamp
Battery cover lever
Status
After taking a picture
Description
The lamp blinks while saving the image and then
turns off when ready to take another picture
While voice memo recording The lamp blinks
When the USB cable is
inserted to a PC
The lamp lights up
(LCD monitor turns off after initializing the device)
Transmitting Data with a PC The lamp turns on (LCD monitor turns off)
ſ To open the battery chamber cover, slide it in the direction shown above.
ŝ8Ş
When the USB cable is
connected to a printer
The lamp is off
When the printer is printing
The lamp blinks
When the AF activates
The lamp lights (The subject is in focus)
The lamp blinks (The subject is not in focus)
Identification of features
ƈ Mode dial
You can select the desired working mode by using the mode dial located on the
top of the camera.
ƃ ASR mode
Advanced Shake Reduction (ASR) mode. This mode will
reduce camera shake and help you get a clearer image.
ƃ AUTO mode
Select this mode for quick and easy picture taking with
minimal user interaction.
ƃ SPECIAL EFFECT mode
It is possible to add special effects to your images by
using this mode.
ƃ PROGRAM mode
Selecting the program mode will configure the camera
with optimal settings. You can still manually configure all
functions except the aperture value and shutter speed.
ƃ SCENE mode
Use the menu to easily configure optimal settings for a
variety of shooting situations.
ƃ ASM mode
You can manually configure all functions including the
aperture value and shutter speed.
ŝ9Ş
Identification of features
Connecting to a Power Source
ƃ MOVIE CLIP mode
A movie clip can be recorded for as long as the available
recording time of the memory capacity allows.
ƃ PHOTO GALLERY mode
The saved images can be reviewed with music or various
effects in this mode.
ƈ You should use the rechargeable battery (SLB-1137D) supplied with the
camera. Be sure to charge the battery before using the camera.
ƈ SLB-1137D rechargeable battery Specification
Model
Type
Capacity
Voltage
SLB-1137D
Lithium Ion
1100mAh
3.7V
Charging time
(When the camera is turned off)
About 150 Min.
ƈ Number of images and battery life : Using the SLB-1137D
Still image
ƈ Mode icon
MODE
AUTO
PROGRAM
A
S
ASR
MOVIE
SPECIAL EFFECT
PHOTO GALLERY
PLAY
Icon
SCENE
MODE
NIGHT
PORTRAIT CHILDREN LANDSCAPE
TEXT
SUNSET
BIZ
CLOSE UP
Icon
MODE
Icon
ŝ10Ş
DAWN
Number of images
Recording time
Approx. 110 MIN
Approx. 220
Approx. 100 MIN
M
Icon
MODE
Movie
Battery life
Using the fully charged battery,
Auto mode, 10M image size,
Based
Fine image quality, Shot to shot
Based
on the
interval : 30Sec.
on the
Changing the zoom position between following
following
shooting
the Wide and the Tele after every
shooting
conditions
shot.
conditions
Using the flash on every second shot.
Using the camera for 5 minutes and
then Powering it off for 1 minute.
Using the fully charged
battery
640X480 image size
30fps frame rate
BACKLIGHT FIREWORKS BEACH&SNOW
ſ These figures are measured under Samsung’s standard conditions and shooting
conditions and may vary depending on the user's methods.
Connecting to a Power Source
a
INFORMATION
Important information about battery usage.
ƃ When the camera is not used, turn off the camera power.
ƃ Please remove the battery if the camera will not be used for long periods.
Battery can lose power over time and are prone to leaking if kept inside the
camera.
ƃ Low temperatures (below 0°C) can affect the performance of the battery
and you may experience reduced battery life.
ƃ Battery will usually recover at normal temperatures.
ƃ During extended use of the camera, the camera body may become warm.
This is perfectly normal.
ƈ You can charge the rechargeable battery (SLB-1137D) by using an SAC-45 KIT.
The SAC-45 consists of the AC adapter (SAC-45) and the USB cable (SUC-C2).
When the AC adapter and the USB cable are assembled, it can be used as an
AC cable.
ƃ Using the SAC-45 as an AC charger
: Insert the AC adapter into the USB connector.
When the AC adapter is inserted, it can be used
as an AC charger.
ƃ Using the SAC-45 as an USB cable
: Remove the AC adapter from the USB connector.
You can transmit data with a PC (p.75) or charge
the battery.
CAUTION
In the following cases, the battery may not be charged.
ƃ When using the USB cable that was not supplied with this camera. Use the
supplied USB cable.
ƃ When using a USB hub. Connect the camera to the PC directly.
ƃ When other USB devices are connected to the PC. Disconnect the other
USB devices.
ƃ When the USB is connected to the USB port located on the front of the
computer. Use the USB located on the back of the computer.
ƃ If the USB port of the PC doesn't meet the Power output standard (5V,
500mA), the camera may not be charged.
ŝ11Ş
Connecting to a Power Source
a
ƈ How to charge the rechargeable battery (SLB-1137D)
ƃ Charging with the camera
Charging LED
ƈ Charging LED of the AC Adapter
Being Charged
Charging is complete
Charging error
Being discharged
(Using the AC adapter)
ŝ12Ş
Charging LED
Red LED is on
Green LED is on
Red LED is off or blinking
Orange coloured LED is on
CAUTION
ƃ Before inserting any cables or AC adapter, check the directions and do not
insert by force. It may cause damage to the cable or camera.
ƃ If the charging LED of the AC Charger does not turn on or blink after
inserting the rechargeable battery, please check whether the battery is
inserted correctly.
ƃ If you charge the battery with the camera power on, the battery can't charge
fully. Turn the camera off while charging the battery.
ƃ If you insert the fully discharged battery to charge it, do not turn on the
camera at the same time. The camera may not be turned on because of the
low battery capacity. Charge the battery for more than 10 minutes before
using the camera.
ƃ Do not use the flash frequently or take a movie clip with a fully discharged
battery that has only been charged for a short time.
a
Connecting
to a Power Source
ƈ Insert the battery as shown
- If the camera does not turn on after you
have inserted battery, please check
whether the battery is inserted with the
correct polarity (+ / -).
- Do not use force to open the battery
chamber. This may damage the battery
chamber cover.
ƈ There are 4 indicators for battery condition that are displayed on the LCD monitor.
Battery
indicator
Battery
status
The battery is
fully charged
Low battery capacity Low battery capacity Low battery capacity
(Prepare to recharge (Prepare to recharge (Prepare to recharge
or use spare battery) or use spare battery) or use spare battery)
Instructions on using the memory card
a
ƃ Be sure to format the memory card (see p.63) if you are using a newly
purchased memory for the first time, if it contains data that the camera cannot
recognise, or if it contains images captured with a different camera.
ƃ Turn off the camera power whenever the memory card is being inserted or
removed.
ƃ Repeated use of the memory card will eventually reduce its performance.
Should this be the case, you will need to purchase a new memory card.
Wear and tear on the memory card is not covered by the Samsung warranty.
ƃ The memory card is an electronic precision device.
Do not bend, drop or subject it to any heavy impact.
ƃ Do not store the memory card in an environment with strong electronic or
magnetic fields, e.g. near loudspeakers or TV receivers.
ƃ Please do not use or store in an environment where there are extremes in
temperature.
ƃ Do not allow the memory card to become dirty or to come into contact with any
liquid. Should this happen, clean the memory card with a soft cloth.
Inserting the memory card
ƈ Turn off the camera's power before inserting the memory card.
- Insert the memory card as shown.
- Have the front of the memory card
facing toward the back of the camera
(LCD monitor) and the card pins
toward the front of the camera (Lens).
- Do not insert the memory card the
wrong way round. Doing so may
damage the memory card slot.
ƃ Please keep the memory card in its case when not in use.
ƃ During and after periods of extended use, you may notice that the memory card
is warm. This is perfectly normal.
ƃ Do not use a memory card that is used in another digital camera.
To use the memory card in this camera, format the memory card using this
camera.
ƃ Do not use a memory card formatted by another digital camera or memory card
reader.
ŝ13Ş
a
Instructions
on using the memory card
ƃ If the memory card is subjected to any of the following, the recorded data may
become corrupted :
- When the memory card is used incorrectly.
- If the power is switched off or the memory card is removed while recording,
deleting (formatting) or reading.
ƃ Samsung cannot be held responsible for lost data.
ƃ It is advisable to copy important data onto other media as back-up e.g. floppy
disks, hard disks, CD etc.
ƈ The camera can use SD/SDHC Memory Cards and MMC (Multi Media Cards).
When using MMC cards, please consult the instructions supplied with the cards.
The SD/SDHC memory card has a write
protect switch that prevents image files
from being deleted or formatted. By sliding
the switch towards the bottom of the
SD/SDHC memory card, the data will be
protected. By sliding the switch towards
the top of the SD/SDHC memory card, the
data protection will be cancelled. Slide the
switch to the top of the SD/SDHC memory
card before taking a picture.
Card pins
Write protect
switch
Label
ƃ If there is insufficient memory available
: A [Memory Full!] message will appear and the camera will not operate.
To optimise the amount of memory in the camera, replace the memory card or
delete unnecessary images stored on the memory card.
[SD (Secure Digital) memory card]
ƈ When using a 256MB MMC memory, the specified shooting capacity will be as
follows. These figures are approximate as image capacities can be affected by
variables such as subject matter and memory card type.
INFORMATION
ƃ Don't remove the memory card when the camera status lamp is blinking as
this may cause damage to data in the memory card.
Recorded image size Super Fine
Still
image
Movie
Fine
Normal
30FPS
10M
49
94
136
-
-
9M P
55
105
151
-
-
7M
65
124
177
-
-
7M W
64
122
174
-
-
5M
87
163
228
-
-
3M
122
221
303
-
-
1M
419
617
733
-
-
640
-
-
-
00:12:42
00:20:51
320
-
-
-
00:30:34
00:57:49
* The recording times can be affected by the zoom operation.
The zoom button doesn't operate while recording movies.
ŝ14Ş
15FPS
When Using the Camera for the First Time : Smart button
ƈ This button is used for shifting the menu cursor to select or for confirming the
selected menu.
ƈ To select a sub menu, in some menus, touch the button and slide your finger to
the left / right.
3648X2056
3136X2352
3648X2432
SIZE
[Selecting the main menu :
Touching the button]
3648X2736
[Confirming the main menu :
Pressing the button]
Slow
Fast
[e.g. : Selecting the shutter speed]
3648X2056
ƈ Extending the menus : Press the extension menu button and more available
menus will display.
3136X2352
3648X2432
3648X2736
[Confirming the sub menu :
Pressing the button]
[Selecting the sub menu :
Touching the button]
Pressing the
extension menu
button
ſ The LCD monitor will be dark when some menus are selected. After selecting
the menu, the LCD monitor returns to the brightness set as before.
ŝ15Ş
When Using the Camera for the First Time : Setting up the Date / Time and Language
ƈ When the camera is turned on for the first time, a menu will be displayed in the
LCD monitor to set date, time and language. This menu will not be displayed
again after setting up the date, time and language. Set up the date, time and
language before using this camera.
ƃ Setting up the date, time and date type
1. Press the [Date&Time] menu button.
2. Select a desired date type by pressing the vertical
smart button.
Ȝ 2007/02/01
yy/mm/dd Ȝ
Language
Date & Time
mm/dd/yy
dd/mm/yy
Off
ƃ Setting up the language
1. Press the [Language] menu button.
2. Select a desired language by pressing the vertical
smart button.
Exit:BACK
ENGLISH Ȝ
Language
Date & Time
FRANÇAIS
DEUTSCH
ह
Exit:BACK
INFORMATION
ƃ You can select any one of 22 languages. These are listed below :
- English, Korean, French, German, Spanish, Italian, S.Chinese, T.Chinese,
Japanese, Russian, Portuguese, Dutch, Danish, Swedish, Finnish, Thai,
BAHASA (MALAY / INDONESIAN), Arabic, Polish, Hungarian, Czech and
Turkish.
ƃ Even if the camera is restarted, the language setting will be maintained.
ŝ16Ş
3. To change the date, select the [2007/02/01] menu
and press the vertical smart button.
4. To select Year / Month / Day and Hour : Minute,
press the horizontal smart button. To change the
numbers, press the vertical smart button.
Ɗ
07 / 02 / 01 12 : 00
ƌ
स
OK
ह
LCD monitor indicator
ƈ The LCD monitor displays information about the shooting functions and selections.
‫ڻ ڼ ڽ‬
‫ں‬
No.
Description
4
Card inserted indicator
Icons
Page
p.13
5
Battery
p.13
6
Optical / Digital Zoom bar /
Digital Zoom rate
p.24~25
7
Focus mode
p.28~29
8
Flash
p.30~31
‫ڹ‬
؊
‫ھ‬
؉
؋
،
؈
‫ۀ‬
‫ہ‬
‫ۂ‬
‫ۃ‬
‫ۄ‬
‫ڿ‬
‫ۅ‬
‫ۆ‬
‫ۇ‬
؅
؆
؇
[Image & Full Status]
No.
Description
1
Recording mode
2
Date / Time
3
Icons
Page
p.9~10
12:00 AM 2007.02.01
Number of available shots remaining
9
Remaining time (Movie clip/ Voice recording)
00:01:00/01:00:00
p.61
p.14
9
Image size
p.31
10
Shooting mode
p.32
11
Metering
p.32
12
Sharpness
p.33
13
Special Effect
p.33
14
Image quality / Frame rate
p.34
15
Self-timer
p.34~35
16
Voice Recording / Without Sound
17
Setup menu
18
Extension menu
p.15
19
Exposure compensation
p.36
p.35~36/p.21
p.58~59
20
ISO
p.36
21
White Balance
p.37
22
Auto focus frame
-
23
Face Recognition
p.25~26
ŝ17Ş
Starting the recording mode
ƈ How to use the AUTO mode (
)
Please select this mode for quick and easy picture taking with minimal user
interaction.
1. Insert the battery (p.13) taking note of the correct
polarity (+ / -).
2. Insert the memory card (p.13). As this camera has
a 20MB internal memory, it is not essential to
insert the memory card. If the memory card is not
inserted, an image will be stored in the internal
memory. If the memory card is inserted, an image
will be stored on the memory card.
3. Close the battery chamber cover.
4. Press the power button to turn on the camera.
(If the date / time that is displayed on the LCD
[AUTO mode]
monitor is incorrect, reset the date / time before
taking a picture.)
5. Select the Auto mode by rotating the mode dial.
6. Point the camera towards the subject and compose the image by using the
LCD monitor.
7. Press the shutter button to capture an image.
INFORMATION
ƃ If the auto focus frame turns to red when you press the shutter button down
half way, it means that the camera cannot focus on the subject. Should this
be the case, the camera is unable to capture an image clearly.
ƈ How to use the PROGRAM mode (
)
Selecting the program mode will configure the
camera with optimal settings. You can still manually
configure all functions except the aperture value and
shutter speed.
1. Select the Program mode by rotating the mode
dial.
2. Press the horizontal smart button to configure
advanced functions such as image size (p.31),
quality (p.34), metering (p.32) and continuous
shooting (p.32).
[PROGRAM mode]
ſ Refer to page 27-41 for more information
about the menus.
ƈ How to use the ASM mode ( ASM )
ƃHow to select the A, S or M mode
1. Select the ASM mode by rotating the mode dial.
2. Select the A, S or M mode by using the smart
button.
M
S
A
M
1/30
F2.8
[A, S or M mode]
ŝ18Ş
Starting the recording mode
ƃ How to use the APERTURE PRIORITY mode (
)
This mode will set the aperture value for automatic
exposure depends on the brightness of the object by
automatic shutter speed setting in the camera.
1. Select the ASM mode by rotating the mode dial.
2. Select the APERTURE PRIORITY mode
(
) by using the smart button.
3. Set the desired aperture value by using the
smart button. (p.41)
4. Point the camera towards the subject and
compose the image by using the LCD monitor.
5. Press the shutter button to capture an image.
ſ Smaller Aperture values make the object sharp
but blur the background. Larger Aperture values
make both the object and background sharp.
ƃ How to use the MANUAL mode (
)
The user can manually set both the aperture value
and the shutter speed.
1. Select the ASM mode by rotating the mode dial.
2. Select the MANUAL mode (
) by using the
smart button. (p.40~41)
3. Select the desired shutter speed and aperture
value by using the smart button.
4. Point the camera towards the subject and
compose the image by using the LCD monitor.
5. Press the shutter button to capture an image.
[APERTURE PRIORITY
mode]
[MANUAL mode]
ƃ How to use the SHUTTER PRIORITY mode (
)
This mode will set the shutter speed for automatic
exposure depending on the brightness of the subject.
1. Select the ASM mode by rotating the mode dial.
2. Select the SHUTTER PRIORITY mode (
) by
using the smart button.
3. Set the desired shutter speed by using the
smart button. (p.40)
4. Point the camera towards the subject and
compose the image by using the LCD monitor.
5. Press the shutter button to capture an image.
ſ High Shutter speeds can 'freeze' a moving
object as if it was not moving. Low Shutter
speeds can capture a moving object with a
blurred or 'active' effect.
[SHUTTER PRIORITY
mode]
ŝ19Ş
Starting the recording mode
ƈ How to use the ASR (Advanced Shake Reduction)
mode (
)
This mode will reduce the effect of camera shake
and help you get a well-exposed image in dim
conditions.
ƈ How to use the SPECIAL EFFECT mode (
)
It is possible to add special effects to your images
by using this mode. Select the Special Effect mode
by rotating the mode dial.
ſ Refer to page 38~40 for more information
about the special effect menus.
ƃ Things to watch out for using the ASR mode
1. The digital zoom will not operate in the ASR mode.
2. If the lighting conditions are brighter than
fluorescent lighting condition, the ASR doesn’t
activate.
[ASR mode]
3. If the subject is moving the final image captured
may be blurred.
4. Avoid moving the camera while the [Capturing!] message is displayed to
achieve a better result.
5. As the ASR uses the camera’s digital processor, images taken using the ASR
may take a little longer for the camera to process.
[SPECIAL EFFECT mode]
ƈ How to use the SCENE mode (
)
Use the menu to easily configure optimal settings
for a variety of shooting situations.
Select the Scene mode by rotating the mode
dial.
ſ Refer to page 38 for more information about
the menus.
[SCENE mode]
ŝ20Ş
Starting the recording mode
ƈ How to use the MOVIE CLIP mode (
)
A movie clip can be recorded for as long as the
available recording time of the memory capacity
allows.
1. Select the MOVIE CLIP mode by rotating the
mode dial. (Available recording time will display
00:00:22
on the LCD monitor)
2. Point the camera towards the subject and
compose the image by using the LCD monitor.
Press the shutter button and movie clips are
recorded for as long as the available recording
time allows. Movie clips will still be recorded if
[MOVIE CLIP mode]
the shutter button is released.
If you wish to stop recording, press the shutter button again.
* Image size and type are listed below.
- Image size : 640X480, 320X240 (Selectable)
- File type : *.avi (MPEG-4)
ſ The maximum file size of continuous movie clip is 4GB.
ſ If the recording time is over 6 hours, though the file size is not 4GB, the movie
is stopped and saved automatically.
ſ Before the file size is 4GB or the recording time is 6 hours, the movie can be
stopped and saved depending on the movie quality.
ƈ To record a movie clip without voice
1. Press the extension menu button.
2. Select the [VOICE] ƍ [OFF] menu.
3. Press the shutter button and movie clip is
recorded for as long as the available recording
time without voice allows.
OFF
ON
[MOVIE CLIP mode]
ƈ Pausing while recording a movie clip (Successive Recording)
This camera allows you to temporarily stop during unwanted scenes, while
recording a movie clip. Using this function, you can record your favourite
scenes into a movie clip without having to create multiple movie clips.
ƃ Using Successive Recording
1. Press the shutter button and movie clips are
recorded for as long as the available recording
time allows. Movie clips will still be recorded if
the shutter button is released.
2. Press the II button to pause recording. Press
the II button again to resume the recording.
3. If you wish to stop recording, press the shutter
button again.
[Successive recording of a
movie clip]
ŝ21Ş
Things to Watch Out for When Taking Pictures
ƈ Pressing the shutter button down half way.
Lightly press the shutter button to confirm focus and flash battery charge.
Press the shutter button all way down to take the picture.
[Lightly press the shutter button]
[Press the shutter button]
ƈ The available recording time may vary depending on shooting conditions and
camera settings.
ƈ When either the Flash Off or Slow synchro mode is selected in a low lighting
condition, the camera shake warning indicator (
) may appear on the LCD
monitor. In this case, use a tripod, support the camera on a solid surface or
change to flash shot mode.
ƈ Shooting against the light :
Please do not take pictures into the sun. Taking a picture against the sun may
make the picture dark. To take a picture against the light, please use the
[Backlight] in the scene shooting mode (see page 38), fill-in flash (see page 30),
spot metering (see page 32), or exposure compensation (see page 36).
ŝ22Ş
ƈ Avoid obstructing the lens or the flash when you capture an image.
ƈ Compose the image by using the LCD monitor.
ƈ In some of the following conditions the auto focus system may not perform as expected.
- When photographing a subject that has little contrast.
- If the subject is highly reflective or shiny.
- If the subject is moving at high speed.
- When there is strong reflected light, or when the background is very bright.
- When the subject matter has only horizontal lines or the subject is very narrow
(such as a stick or flagpole).
- When the surroundings are dark.
Using the camera buttons to set the camera
ƈ The recording mode function can be set up by using the camera buttons.
POWER button
ƃ Used for turning the camera’s power on / off.
ƃ If there is no operation during the specified
time, the camera's power will be turned off
automatically to save battery life.
Refer to page 62 for more information about
the auto power off function.
Shutter button
ƃ Used for taking an image or recording voice in
the RECORDING mode.
ƃ In MOVIE CLIP mode :
Pressing the shutter button down fully starts
the process for recording a movie clip.
Press the shutter button once and the movie
clip is recorded for as long as the available
recording time in the memory allows. If you wish to stop recording, press the
shutter button again.
ƃ In STILL IMAGE mode :
Pressing the shutter button down halfway activates the autofocus and checks
the condition of the flash. Pressing the shutter button down fully takes and stores
the image. If you select voice memo recording, the recording will start after the
camera has finished storing the image data.
ŝ23Ş
ZOOM W / T button
ƃ If the menu is not displayed, this button works
as the OPTICAL ZOOM or DIGITAL ZOOM
button.
ƃ WIDE Zoom
Optical zoom WIDE
ƃ This camera has a 5X optical zoom and a 5X digital zoom function.
Using both will offer a total zoom ratio of 25X.
[WIDE zoom]
[TELE zoom]
[TELE zoom]
Digital zoom WIDE
Digital
zoom
Optical
zoom
Pressing
the ZOOM
T button
Pressing
the ZOOM
T button
[Optical zoom 2X]
[Digital zoom 5X]
[WIDE zoom]
: When the digital zoom is in operation, pressing the
ZOOM W button will reduce the digital zooming in steps.
Releasing ZOOM W button stops digital zooming.
Pressing the ZOOM W button will reduce the digital
zoom and then it will continue to reduce the optical
zoom until the minimum setting is reached.
Pressing
the ZOOM
W button
Pressing
the ZOOM
W button
[Digital zoom 5X]
ŝ24Ş
Pressing
the ZOOM
W button
Pressing
the ZOOM
W button
ƃ TELE Zoom
Optical zoom TELE : Pressing the ZOOM T button will zoom into the subject i.e.
the subject will appear nearer.
Digital zoom TELE : When the maximum (5X) optical zoom is selected,
pressing the ZOOM T button activates the digital zoom
software. Releasing ZOOM T button stops the digital
zooming at the required setting. Once the maximum
digital zoom (5X) is achieved, pressing the ZOOM T
button will have no effect.
: Pressing the ZOOM W button. This will zoom out from
the subject i.e. the subject will appear farther away.
Pressing the ZOOM W button continuously will set the
camera to its minimum zoom setting i.e. the subject
appears at its farthest from the camera.
[TELE zoom]
[WIDE zoom]
ZOOM W / T button
INFORMATION
ƃ Images taken using the digital zoom may take a little longer for the camera
to process. Allow time for this to take place.
ƃ If the Zoom buttons are being pressed during the Movie clip shots, the voice
will not recorded.
ƃ You may notice a decrease in image quality when using the digital zoom.
ƃ To view a clearer digital zoom image, press the shutter button halfway at the
maximum optical zoom position and press the zoom T button again.
ƃ The digital zoom can’t be activated in the MOVIE CLIP, ASR, High Speed,
Motion Capture mode, [Night], [Children], [Biz], [Close up], [Text] and
[Fireworks] scene modes.
ƃ Take care not to touch the lens to avoid taking an unclear image and
possibly causing camera malfunction. If the image is dim, turn the camera
power off and on again to modify the lens position.
ƃ Take care not to press the lens as this may cause a camera malfunction.
ƃ When the camera is turned on, take care not to touch the camera's moving
lens parts as this may cause the resulting image to be dim and unclear.
ƃ You can operate the Wide and Tele zoom by using the remote control.
Face recognition(FR) button
ƈ Face recognition
This mode detects the face position of the subject automatically and then sets
the focus and exposure. Select this mode for quick and easy face picture.
Selectable modes : Auto, Program, ASR, Effect(GIF), A/S/M, Scene(Portrait,
Children, Beach & Snow)
1. Press the FR (Face Recognition) button (
) in
the selectable modes.
The FR icon will be displayed on the screen left
side.
2. The size and position of the auto focus frame is
set at the face of the subject automatically.
3. Press the shutter button halfway. The focus frame turns to green when the
focus is activated.
4. Press the shutter button fully to take a picture.
ŝ25Ş
Face recognition(FR) button
INFORMATION
ƃ This function can detect up to 8 persons.
ƃ When the camera recognises many people at the same time, it will focus on
the nearest person.
ƃ When the camera detect a target face, the white colour focus frame will
display over the target face and the gray colour focus frame will display over
the rest faces(up to 7). Press the shutter button halfway down to focus the
face and the white focus frame turns green.(Total 8)
ƃ Return to previous AF mode if face detection was failure.
ƃ In some conditions this function cannot work properly.
- When a person wears dark glasses or some part of the face is hidden.
- When the person being taken does not look at the camera.
- Camera doesn't detect a face as the brightness is too dark or too bright.
- The distance between the camera and object are far.
ƃ The maximum available Face Recognition range is 2.1m (Wide).
ƃ The nearer the subject, the faster the camera can recognize the subject.
Using the LCD monitor to set the camera
ƈ You can use the menu on the LCD monitor to set up recording functions.
(O : Selectable, X : Not selectable, - : Partly selectable)
MENU
COLOR
BRIGHT
MANUAL
NORMAL
FOCUS AUTO MACRO
MACRO
SUPRE MACRO
OFF
AUTO
RED EYE
FLASH
FILL IN
SLOW SYNC
RED EYE FIX
SIZE
SINGLE
CONTINUOUS
SHOOTING HIGH SPEED
MOTION CAPTURE
AEB
QUALITY
TIMER
ŝ26Ş
OFF
10SEC
2SEC
Double
REMOTE
ASM
O
O
X
O
O
X
O
O
O
O
X
X
O
O
O
X
X
X
X
O
O
O
O
O
O
X
X
O
O
X
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
X
X
O
O
X
O
O
O
X
X
O
X
X
O
O
O
O
O
X
O
O
O
O
O
O
X
X
X
O
X
O
X
O
X
X
X
X
X
O
O
X
X
X
X
O
O
O
O
O
O
X
X
X
O
X
O
O
O
O
O
O
O
O
O
O
X
X
X
X
O
O
O
O
X
O
X
X
X
X
O
O
X
X
X
X
O
O
O
O
O
O
X
X
X
O
X
O
X
X
X
X
X
X
X
O
X
X
X
X
X
O
O
O
X
X
O
page
p.27
p.28
p.28~
29
p.30~
31
p.31
p.32
p.34
p.34~
35
Using the LCD monitor to set the camera
MENU
page
ASM
VOICE
O
O
O
O
O
O
O
p.35~36
W/B
X
O
O
X
X
X
O
p.37
ISO
X
O
X
X
X
p.36
X
O
O
*1O
X
EV
X
X
X
O
p.36
MULTI
O
O
O
O
O
-
O
SPOT
X
O
O
X
O
-
O
CENTER
X
O
O
X
O
-
O
METERING
SHARPNESS
X
O
O
X
O
X
X
p.33
X
X
X
X
O
X
X
p.38
M.GIF
X
X
X
X
O
X
X
p.39
COMPOSITE
X
X
X
X
O
X
X
p.39~40
NORMAL
O
O
O
O
O
-
O
B&W
X
O
O
X
O
-
O
SEPIA
X
O
O
X
O
-
O
B
X
O
O
X
O
-
O
R
X
O
O
X
O
-
O
G
X
O
O
X
O
-
O
NEGATIVE
X
O
O
X
O
-
O
CUSTOM
X
X
X
X
O
-
X
ƈ You can add colour tone on the captured image.
Warm menu will increase red colour of the image.
Cool menu will increase blue colour of the image.
COLOR
p.32
PHOTO FRAME
EFFECT
Colour tone
ƃ Selecting the colour tone
To select the colour tone, touch the button and slide your finger to the left or
right.
p.33
[Emphasizing the Cool-colour]
[Emphasizing the Warm-colour]
ſ Menus are subject to change without prior notice.
ſ The selectable menus may vary in each scene modes.
ſ *1 It is not selectable in the MANUAL mode.
ŝ27Ş
Brightness
Selecting focus type
ƈ You can change the brightness of the image.
BRIGHT
ƈ You can select the focus type in accordance with
the subject distance.
The distance ranges are show below.
SUPRE MACRO
MACRO
NORMAL(AF)
MANUAL
ƃ Changing the brightness
To select the brightness, touch the button and slide your finger to the left or right.
[Dark]
ŝ28Ş
[Manual]
[Auto]
[Macro]
[Super Macro]
[Bright]
[Auto Macro]
Selecting focus type
ƃ Types of focus modes and focus ranges (W : Wide, T : Tele)
Focus Type
Wide(W)
Tele(T)
Normal
80cm-Infinity
1.5m~Infinity
Macro
10cm~80cm
50cm~80cm
Auto Macro
10cm-Infinity
50cm-Infinity
Super Macro
Manual Focus
1~10cm (Wide only)
1cm-Infinity
50-Infinity
ƈ Manual Focus (MF)
Where the automatic focusing is not available, for example, in very dark
conditions, use the manual focus. Please be careful when using the manual
focus as the picture can be blurred easily.
You can use the manual focus in the program mode and ASM mode.
ƃ How to set the manual focus
To set to manual focus, touch the button and slide your finger to the left or
right.
INFORMATION
ƃ When the macro mode is selected, it is possible that camera shake will
occur. Take care not to shake the camera while taking a picture.
ƃ When you take a picture within 30cm in the Macro mode, select the FLASH
OFF mode.
4.5m
1.5m
80cm
40cm
1cm
MF
4.5m
[Farther focus]
1.5m
80cm
40cm
1cm
MF
[Closer focus]
ſ Touching the ‫ڹ‬,‫ ں‬button will move the cursor
continuously when you change the manual focus.
4.5m
‫ڹ‬
1.5m
80cm
40cm
1cm
MF
‫ں‬
ŝ29Ş
Flash
ƈ You can select the flash type in accordance with the
subject distance.
The distance ranges are show below.
ƈ When using the ASR, Continuous shot, High Speed
Continuous shot, Motion Capture, AEB, Movie clip
mode and Still image mode (except the NIGHT,
PORTRAIT, CHILDREN, BACKLIGHT and BEACH
& SNOW mode), the flash will not operate.
INFORMATION
FILL IN
RED EYE
AUTO
OFF
7
ſ When Super macro is selected, the flash is automatically switched off.
ſ When [CONTINUOUS], [HIGH SPEED], [M. CAPTURE], [AEB] is selected, the
flash is automatically switched off.
ƈ Flash range (W : Wide, T : Tele)
ISO
AUTO
ŝ30Ş
Normal
W: 0.8 - 4.9
T: 1.5 - 3.0
(Unit : m)
Macro
W: 0.3 - 0.8
T: 0.5 - 1.5
Auto macro
W: 0.3 - 4.9
T: 0.5 - 3.0
ƃ If you press the shutter button after selecting the Auto, Fill-in, Slow sychro
flash, the first flash fires to check the shooting condition (Flash range and
Power ratio of flash).
Do not move the camera until the second flash fires.
ƃ Using the flash frequently will reduce the life of the battery.
ƃ Under normal operating conditions the charging time for the flash is usually
less than 5 seconds. If the battery is weak, the charging time will be longer.
ƃ Take photographs within the flash range.
ƃ The image quality is not guaranteed if the subject is too close or highly
reflective.
ƃ When taking an image in poorly lit conditions with the flash, there may be a
white speck in the captured image. The speck is caused by the reflection of
the flash light from the atmospheric dust. It is not camera malfuction.
ƃ Do not open the Built-in flash by force. It may cause damage to the flash.
Flash
Size
ƃ Flash mode indicator
Menu tab
Flash mode
Flash off
ƈ You can select the image size appropriate for your application.
Description
The flash does not fire. Select this mode when capturing
images in a place or situation where flash photography
is prohibited. When you capture an image in a poorly lit
condition, the camera shake warning indicator (
)
will display on the LCD monitor.
Auto flash
If the subject or background is dark, the camera flash
will operate automatically.
Auto &
Red eye
reduction
If a subject or background is dark, the camera flash
will work automatically and will reduce the red-eye
effect by using the red-eye reduction function.
Mode
Still image mode
Icon
Size
3648X
2736
Mode
3648X
2432
3136X
2352
3648X
2056
2688X
2016
2240X
1680
1024X
768
Movie clip mode
Icon
640
320
Size
640X480
320X240
3048x2056
3136x2352
Fill in flash
Slow synchro
Red-eye fix
The flash fires regardless of the available light. The
intensity of the flash will be automatically controlled to
suit the prevailing conditions.
The flash operates with a slow shutter speed to
obtain a balanced correct exposure. In poor lighting
conditions the camera shake warning indicator
(
) will display on the LCD monitor.
3648x2432
320x240
3648x2736
640x480
7
[STILL IMAGE mode]
[MOVIE CLIP mode]
INFORMATION
ƃ The higher the resolution, the lower the number of shots available because
high resolution images require more memory.
When a shot with "red eye" is detected, this mode
will reduce the red-eye effect automatically.
ŝ31Ş
Continuous shot
ƈ You can select the type of shooting and the number of continuous shots.
- SINGLE
: Take one picture only
AEB
- CONTINUOUS : Images will be taken continuously
M. CAPTURE
HIGH SPEED
until the shutter button is released.
CONTINUOUS
The shooting capacity depends on
SINGLE
the memory.
- HIGH SPEED : This takes 3 shots continuously
(2.5 shots per second) when the
[Still image mode]
shutter is pressed and held down.
- M. CAPTURE : This takes 7 shots per second, when the shutter is pressed
and held down. After completing the continuous shooting,
images are saved and the images play back on the Rear
LCD. The maximum number of shots is 20 and the image
size is fixed as 1024X768.
- AEB : Take three pictures in a series using different exposures : Short
exposure (-1/2EV), standard exposure(0.0EV) and over exposure
(+1/2EV).
Use this mode if it is hard to decide exposure of the object.
ſ High resolution and picture quality increases file saving time, which increases
stand-by time.
ſ If the [CONTINUOUS], [HIGH SPEED], [M. CAPTURE] or [AEB] sub menu is
selected, the flash is switched off automatically.
ſ It is best to use a tripod for the AEB shooting as the time to save each image
file is longer and blurring caused by camera shake may occur.
ſ When the [M.CAPTURE] menu is selected, you only can select ISO AUTO,
400, 800, 1600
ŝ32Ş
Metering
ƈ If you cannot obtain suitable exposure conditions, you can change the metering
method to take brighter pictures.
- MULTI
: Exposure will be calculated based on
an average of the available light in the
CENTER
image area. However, the calculation
SPOT
will be biased towards the centre of the
MULTI
image area. This is suitable for general
use.
- SPOT : Only the rectangular area in the centre
[PROGRAM mode]
of the LCD monitor will be metered for
light. This is suitable when you want the subject in the centre
correctly exposed, regardless of the back lighting.
- CENTER : Exposure will be calculated based on an average of the available
light in the image area. However, the calculation will be biased
towards the centre of the image area. This is suitable for taking a
picture of small object like a flower or insects.
ſ If the subject is not the centre of the focus area, do not use the spot metering
as this may result in an exposure error. In this circumstance, it is better to use
exposure compensation.
Sharpness
Effect
ƈ You can adjust the sharpness of the picture you
want to take. You cannot check the sharpness effect
on the LCD monitor before you take a picture,
because this function is applied only when the
captured image is stored on the memory.
ƈ By using the cameraŖs digital processor, it is possible to add special effects to
your images
VIVID
NORMAL
SOFT
7
[PROGRAM mode]
(
(
(
(
Sub menu
SOFT
NORMAL
VIVID
Icon
Description
The edges of the image are softened.
This effect is suitable for editing images on your PC.
The edges of the image are sharp.
This is suitable for printing.
(
(
(
(
) : No effect is added to the image
BLUE
) : Captured images will be stored in black
SEPIA
and white.
B&W
) : Captured images will be stored in a sepia
NORMAL
tone (a range of yellowish brown colours).
) : Captured images will be stored in a blue
[Program mode]
tone.
) : Captured images will be stored in a red tone.
) : Captured images will be stored in a green tone.
) : Save the image in negative mode.
) : User can set the tone of the R (Red), G (Green) and B (Blue) value.
These menus can be selected in the Special Effect mode only.
The edges of the image are emphasized.
The edges will appear sharp, but noise may occur in
the recorded image.
ŝ33Ş
Quality / Frame rate
Self-timer / Remote control
ƈ You can select the compression ratio appropriate for your application of the
captured images. The higher the compression ratio, the lower the picture quality.
Still image mode
Mode
Movie clip mode
Icon
Sub menu
Super Fine
Fine
Normal
30FPS
15FPS
File Type
jpeg
jpeg
jpeg
avi
avi
ƈ This function is used when the photographer would also like to be in the picture.
- Selecting a self-timer :
REMOTE
When you press the Shutter button, the picture will
DOUBLE
be taken after the specified time has elapsed and
2 sec
10 sec
the self-timer function will be cancelled.
OFF
- Selecting a remote mode :
Pressing the shutter button of a separate remote
control will allow an interval of 2 seconds before
the image is taken. After taking a picture, the
remote mode will be maintained. But, pressing the Power button will cancel the
remote mode.
Normal
Fine
15FPS
Super Fine
30FPS
ƃ Description of Self-timer / Remote mode
Icon
[STILL IMAGE mode]
[MOVIE CLIP mode]
INFORMATION
ƃ This file format complies with the DCF (Design rule for Camera File
system).
ƃ JPEG (Joint Photographic Experts Group) : JPEG is the image
compression standard developed by the Joint Photographic Experts Group.
This type of compression is most commonly used for compressing photos
and graphics because it can compress the files efficiently.
ŝ34Ş
Mode
Description
Off
You do not use the self-timer function.
10s
Pressing the shutter button will allow an interval of
10 seconds before the image is taken.
2s
Pressing the shutter button will allow an interval of
2 seconds before the image is taken.
Double
A picture will be taken after about 10 seconds and
2 seconds later a second picture will be taken.
Remote
You can take a picture by remote control instead of using
the shutter button of the camera.
Self-timer / Remote control
ƃ Remote control range
When you take a picture by using the remote control,
refer to the illustrations shown alongside about the
remote control range.
[Shutter button on the
remote control]
ƃ Replacing battery for the remote control
Make sure the + (positive) polarity is toward the top and the - (negative) polarity is
toward the bottom while installing battery for the remote control. Replace battery for
the remote control in the local service centre. Use the CR 2025 3V battery.
INFORMATION
ƃ When taking a picture using the self-timer, the self-timer lamp works as follows :
2 second self-timer setting : The self-timer lamp blinks at 0.25 second
interval for 2 seconds.
10 second self-timer setting : The self-timer lamp blinks at 1 second interval
for the first 7 seconds. It blinks at 0.25 second
interval for the remaining 3 seconds.
ƃ If you operate the Back button during the self-timer operation, the self-timer
function is canceled.
ƃ Use a tripod to prevent camera shake.
Voice recording / Voice memo
ƈ A voice can be recorded for as long as the
available recording time(Max 10 hours) of the
memory capacity allows. And you can add your
voice-over to a stored still image.
RECORD
MEMO
OFF
ƃ Voice recording
1. Select a recording mode with the exception
of the Movie clip mode by rotating the mode dial.
RECORD
2. Select the Voice recording menu by using
MEMO
the smart button.
OFF
3. Press the shutter button to record a voice.
- Press the shutter button once and voice is
recorded for as long as the available
recording time allows(Max 10 hours) . The recording time will be displayed
on the LCD monitor. Voice will still be recorded if the shutter button is
released.
- If you wish to stop recording, press the shutter button again.
- File type : *.wav
ƃ Voice memo
1. Select a recording mode with the exception
of the Movie clip mode by rotating the mode dial.
RECORD
2. Select the Voice memo menu by using the smart
MEMO
button. If the voice memo indicator is displayed on
OFF
the LCD monitor, the setting is completed.
3. Press the shutter button and take a picture.
The picture is stored on the memory card.
4. Voice memo will be recorded for ten seconds from
the moment the picture is stored. In the middle of the sound recording,
pressing the shutter button will stop the voice memo.
ŝ35Ş
Voice recording / Voice memo
ISO
INFORMATION
ƃ A distance of 40cm between you and the camera (microphone) is the best
distance to record sound.
Exposure compensation
ƈ This camera automatically adjusts the exposure according to the ambient
lighting conditions. You can also select the exposure value in the compensating
exposure menu. Exposure compensation menu is available in the Program,
ASM (Excluding M mode) and Movie clip mode.
ƃ Compensating Exposure
1. Press the exposure compensation menu button
and the exposure compensation menu bar will
appear as shown.
2. Touch the button and slide your finger to select
the exposure value.
3. Press the exposure compensation menu button
again. The value you set will be saved and the
Exposure Compensation setup mode will close.
- AUTO :
The camera's sensitivity is automatically changed
by variables such as lighting value or subject
brightness.
- 80, 100, 200, 400, 800, 1600 :
You can increase the shutter speed while the
same amount of light is present, by increasing the
ISO sensitivity. However, the image may be
saturated in high luminance.
The higher the ISO value, the greater is the camera’s sensitivity to light;
therefore it has a greater capacity for taking pictures in darker conditions.
However, the noise level in the image will increase as the ISO value increases,
making the image appear coarse.
ſ When the [M.CAPTURE] menu is selected, you only can select ISO AUTO,
400, 800, 1600.
-2.0
+2.0
ſ A negative exposure compensation value reduces the exposure.
Note that a positive exposure compensation value increases the exposure
and the LCD monitor will appear white or you may not get good pictures.
ŝ36Ş
ƈ You can select the ISO sensitivity when taking pictures.
The speed or specific light-sensitivity of a camera is rated in ISO numbers.
ISO menu is available in the Program and ASM mode.
White balance
ƈ The white balance control allows you to adjust the colours to appear more
natural. When a menu except the AWB (Auto White Balance) is selected, you
can only select the negative color effect.
White Balance menu is available in the Program, ASM and Movie clip mode.
AUTO
DAYLIGHT
CLOUDY
Fluorescent H
Fluorescent L
TUNGSTEN
CUSTOM
: The camera automatically
selects the appropriate
white balance settings,
depending on the
prevailing lighting
conditions.
: For taking images outside.
: For taking images under a cloudy and overcast sky.
: For shooting under daylight fluorescent types of three
way fluorescent lighting.
: Shooting under white fluorescent lighting.
: For shooting under tungsten (standard light bulb)
lighting.
: Allows the user to set the white balance according to
the shooting condition.
ƃ Using the Custom White Balance
White balance settings may vary slightly depending on the shooting
environment. You can select the most appropriate white balance setting for a
given shooting environment by setting up the custom white balance.
1. Select the CUSTOM (
) menu of the
White Balance and place a sheet of white
paper in front of the camera so that the LCD
monitor shows only white.
2. OK menu button : selects pre-saved custom
white balance.
ٌ
[White paper]
BACK button
: cancels the custom white
balance.
Shutter button : stored the new custom white balance.
- The custom white balance value will be applied, starting with the next picture
you take.
- The user configured white balance will be remain effective until it is
overwritten.
Different lighting conditions may cause a colour cast on your images.
ŝ37Ş
Scene menu
ƈ Use the menu to easily configure optimal settings for a variety of shooting
situations.
ſ The scene modes are listed below.
[NIGHT]
(
) : Use this for shooting
still images at night
or in other dark
conditions.
[PORTRAIT]
(
) : To take a picture of
a person.
[CHILDREN]
(
) : To take a picture of
fast moving objects, for example, children.
[LANDSCAPE] (
) : To take pictures of distant scenery.
[BIZ]
(
) : To take pictures of a visiting card
[CLOSE UP]
(
) : Close-up shooting for small objects such as plants
and insects.
[TEXT]
(
) : Use this mode to shoot a document.
[SUNSET]
(
) : For taking pictures of sunsets.
[DAWN]
(
) : Daybreak scenes.
[BACKLIGHT]
(
) : For portraits without shadows caused by backlighting.
[FIREWORK]
(
) : Firework scenes.
[BEACH&SNOW] (
) : For ocean, lake, beach and snow scape scenes.
ŝ38Ş
Special Effect : Photo Frame
ƈ You can add any one of 9 types of frame-like
borders to a still image you want to capture.
ƈ Date & Time information will not be printed on the
stored image taken with Photo Frame menu.
: The photo frame is not inserted.
Special Effect : Motion GIF
Special Effect : Composite shooting
ƈ You can make Motion GIF with captured images.
Motion GIF : Taking images continuously and save them in a file. This file
supports animation.
ƃ How to make the Motion GIF
1. Select the Special Effect mode by rotating the
mode dial.
2. Press the Motion GIF menu button.
3. Select the image size and FPS (Frame Per Second).
4. Press the Shutter button to take pictures.
(Max. 50 images)
5. Press the OK menu button to save the image.
The images will be saved as a motion GIF file.
ƈ You can combine 2, 3, or 4 different shots in a still image
-
: Cancels the composite shooting
: 2 different shots are combined in a still
image.
: 3 different shots are combined in a still
image.
: 4 different shots are combined in a still
image.
: 2 different panorama shots are combined in a still image.
ſ Selecting 2 composite shooting
Pressing
the shutter
button
320x240
2 FPS
400x300
5 FPS
[Selecting FPS]
[Selecting image size]
Pressing
the shutter
button
Capture:SH
[Ready for taking]
Del:Back
[First shot]
9
OK
Save:OK
Pressing
the OK
menu button
Del:Back
[Second shot]
[The final picture]
[Taking pictures]
INFORMATION
Save:OK
Cancel:BACK
ƃ If you press the Play mode button or rotate the mode dial during the
composite shots, each camera working mode is executed. The images
captured before will be deleted.
ƃ After taking the last composite shooting, press the OK button. And then the
voice memo will start.
[Pressing the OK menu button]
INFORMATION
ƃ As the GIF file format has limitation of shades, image quality can be decreased.
ŝ39Ş
Special Effect : Composite shooting
ƃ Changing a part of composite shot before taking the last shot
Before taking the last composite shot, you can change a part of composite shot.
1. During the composite shots, press the BACK button.
2. A previous image will be deleted and new frame will display. If there is an
image taken before, press the BACK button again and a previous image will
be deleted again.
Capture:SH
Del:Back
Pressing the BACK button
[Before taking the 3rd shot]
Capture:SH
Shutter Speed
ƈ This mode will set the shutter speed for automatic
exposure. High Shutter speeds can capture a
moving object in a still image as if the object is not
moving. Low Shutter speeds can capture a moving
object with an ‘active’ effect.
Del:Back
[Moving backward to the 2nd shot]
[SHUTTER PRIORITY mode]
[MANUAL mode]
3. Press the shutter button to capture a new image.
ƃ Setting up the shutter speed
To select the shutter speed, touch the button and slide your finger to the left or
right. You can set up the Shutter speed in the SHUTTER PRIORITY mode
and in the MANUAL mode.
ƃ Changing a part of composite shot after taking the last shot
1. After taking the last shot, a menu will display as
shown.
2. Select an image to delete by using the Smart
button.
3. Press the BACK button and the selected image is
deleted.
4. Press the Shutter button to take an image again.
5. Press the OK button and the image is saved.
9
+1.0
SLOW
Save:OK
Del:BACK
-2.0
FAST
SLOW
Slow
ŝ40Ş
FAST
F7.3
F7.3
Fast
Aperture Value
Photo Gallery mode
ƈ This mode will set the aperture value for automatic exposure.
Smaller Aperture values make the object sharp but blur the background.
Larger Aperture values make both the object and background sharp.
ƈ When the images play back, you can add play back effect and listen to a B.G.M.
Only still images can be played back. Movie, Voice files are not played back.
ƈ Selecting a play back mode
1. Select the Photo Gallery mode by rotating
the mode dial.
[APERTURE PRIORITY mode]
[MANUAL mode]
2. Press the Play mode button and menus as
shown will display.
ƃ Setting up the Aperture value
To select the Aperture Value, touch the button and slide your finger to the left
or right.
You can set up the Aperture value in the APERTURE PRIORITY mode and
the MANUAL mode.
: Play back by album
: Play back by date
3. Press the Smart button to select a desired play back mode.
A
A
F4.4
CLOSE
F3.6
OPEN
Close
CLOSE
OPEN
Open
ŝ41Ş
Photo Gallery mode
ƈ Album mode : Images play back by album.
If a memory card is not inserted, Personal / Family / Friend / Event
albums can be selected. All of images saved in the internal
memory play back.
ƃ Selecting an album
You can select an album by using the smart
button. Before selecting an album, insert images
into albums.
: All images save in the memory play back.
: Images saved in the Personal album play
back.
: Images saved in the Family album play back.
: Images saved in the Friends album play back.
: Images saved in the Events album play back.
ƃ Adding images in an album
Press the Album menu button and the menus
shown below will display.
- Moving cursor / Selecting an image
: Smart button (Horizontal)
- Selecting images
: Pressing the smart button (Horizontal)
Images you want can be selected one at a time.
Select:
- Selecting / Cancellingl an album
: Each album button
: Adding images in the Personal album.
: Adding images in the Family album.
: Adding images in the Friends album.
: Adding images in the Events album.
- Moving to previous menu : BACK button
ŝ42Ş
View:BACK
Photo Gallery mode
ƃ Playing back an album
Press the slide show menu button.
100-0001
: Starting the slide show
: Selecting an effect of the slide show
: Setting play interval
: Selecting a B.G.M
A B.G.M can be played back with images.
OFF
Only a saved music can be selected.
You can’t add any music on the B.G.M list.
: Selecting play back time
[Play] : The slide show is closed after one cycle.
[Repeat Play] : The slide show is repeated until cancelled.
ſ Refer to page 48~49 for more information about the slide show.
ƃ Rotating an image
You can rotate an image to a direction you want.
Press the horizontal smart button.
Touch the smart button and the selected image is
rotated. Press the smart button and the rotated
image information will be saved.
: rotates the image clockwise.
: rotates the image anticlockwise.
ƈ Date mode : When an image is taken, date information is also recorded.
In date mode, images play back by the date.
ƃ Selecting a date
You can select a date by using the smart button.
ſ Usage of the menu of the date mode is same as
album mode. Refer to p.42 for more information.
ŝ43Ş
Starting play mode
ƈ Turn the camera on and select Play mode by pressing the play mode button
(
). The camera can now play back the images stored in the memory.
ƈ You can set up the PLAY mode function by using the camera buttons and LCD
monitor.
ƈ If the memory card is inserted in the camera, all the camera functions apply only
to the memory card.
ƈ If the memory card is not inserted in the camera, all the camera functions apply
only to the internal memory.
ƃ Playing back a still image
ƃ Manner mode : To select the Manner mode, press the Playback mode
button for more than 3 seconds. In the Manner mode,
Shutter sound, Operating sound, Start-up sound and Effect
sound will not be generated. To cancel the Manner mode,
turn on the camera by pressing the Power button.
ƃ Playing back a movie clip
1. Select the PLAY mode by pressing the
play mode button (
).
1. Select the recorded movie clip that you want to
play back by using the smart button.
2. Press the [Play] button and menus for movie will
display.
3. Press the Ȟ button to play back a movie clip file.
- To pause a movie file while playing it back,
press the II button again.
- Pressing the Ȟ button again will cause the
movie clip file to restart.
- To rewind the movie clip while it is playing,
press the ȜȜ button. To fast forward the
movie clip, press the ȞȞ button. Whenever
the ȜȜ/ȞȞ button is pressed, the search
speed will be increased to 2X, 4X, 8X or 16X.
- To stop playback of the movie clip, press the ְ button.
4. Press the BACK button and the menu move to Play mode.
2. The last image stored on the memory is
displayed on the LCD monitor.
3. Touch the button and slide your finger to
the left or right to select an image.
ſIf you press the ‫ ڹ‬or ‫ ں‬button, the image
will be play back continuously
‫ڹ‬
ŝ44Ş
INFORMATION
‫ں‬
Starting play mode
ƃ Playing back a recorded voice
ƃ Movie clip capture function : capture still images from the movie clip.
1. Press the II menu button while playing back a
movie file.
2. Press the Capture menu button. The captured
image is saved under a new file name.
100-0001
00:00:15
Capture
1. Select the recorded voice that you want to play
100-0001
back by using the smart button.
2. Press the [Play] button; menus for voice will
display.
3. Press the Ȟ button to play back a voice clip file.
- To pause a voice file while playing it back, press
the II button again.
- Pressing the Ȟ button again will cause the voice file to restart.
- To rewind the voice while it is playing, press the ȜȜ button. To fast forward
the voice, press the ȞȞ button.
- To stop playback of the voice, press the ְ button.
ƃ On camera movie trimming : You can extract desired frames of movie clip during
the movie clip play back.
1. Press the extract menu button at the point of the
movie clip that you want to start extracting.
2. Press the extract menu button at the point of the
movie clip that you want to stop extracting.
3. A confirmation window will display.
4. Press the smart button to select a desired sub
menu.
[Yes] : The extracted frames are saved as a new
file name.
[No] : The movie trimming will cancel.
Trimming?
Yes
No
ſ If the running time is under 4 seconds, the movie clip can’t be trimmed.
ŝ45Ş
Starting play mode
LCD monitor indicator
ƈ The LCD monitor displays shooting information about the displayed image.
ƃ Playing back a recorded voice memo
1. Select the still image that includes the voice
memo by using the smart button.
2. Press the [Edit] button and menus will display.
3. Press the ( ) icon to play back a voice memo.
- To pause a voice file while playing it back,
press the II button.
- Pressing the Ȟ button again will cause the
voice file to restart.
- To stop playback of the voice, press the ְbutton.
‫ۃ‬
‫ڹ‬
MEMO PLAY
‫ۂ‬
‫ہ‬
‫ں‬
‫ۀ‬
ISO : 80
Av : F3.5
Tv : 1/50
FLASH : OFF
3648X2736
2007.02.01
‫ڿ‬
‫ھ‬
‫ڻ‬
ŝ46Ş
No.
1
2
3
4
5
6
7
8
9
10
Description
Battery
Recording Information
Slide Bar
Fn menu : Press the smart button
Setup menu
DPOF menu
Delete menu
Protect menu
Slide show menu
Play back mode icon
11
Folder name and Stored
image number
‫ڼ‬
‫ڽ‬
Icon
Edit
/ Play
100-0001
Page
p.13
p.58~59
p.50
p.50
p.49
p.48~49
p.60
Using the camera buttons to adjust the camera
ƈ In Play mode, you can use the buttons on the camera to conveniently set up the
Play mode functions.
Thumbnail (
) / Enlargement (
) button
ƃ You can view multiple pictures, enlarge a selected picture, and crop and save
a selected area of an image.
ƃ Thumbnail display
Play mode button
ƈ If you have turned on the camera by pressing the POWER button, you can press
the PLAY MODE button once to switch to Play mode and press it again to switch
to Recording mode.
ƈ You can turn the power on with the play mode button. The camera is turned on
in play mode. Press the play mode button again to turn off the camera.
ISO sensitivity
Aperture value
Shutter speed
Whether or not the flash is used
Size
Recording date
ISO : 80
Av : F3.5
Tv : 1/50
FLASH : OFF
3648X2736
2007.02.01
1. While an image is displayed on full screen, press the
thumbnail button.
2. The thumbnail display will highlight the image that
had been showing at the time the thumbnail mode
was selected.
3. Use the smart button to move to a desired image.
4. To view an image separately, press the enlargement button.
Pressing the thumbnail
button (
)
ISO : 80
Av : F3.5
Tv : 1/50
FLASH : OFF
3648X2736
2007.02.01
Pressing the enlargement
button (
)
Select:
[Normal display mode]
Full:T
[Thumbnail display mode]
BACK button
ƈ When the menus are displayed the BACK
button allows you to return to the previous
screen, and will eventually bring you out of the
menu system.
ŝ47Ş
Thumbnail (
) / Enlargement (
) button
ƃ Image enlargement
ƈ Images can be displayed continuously at pre-set intervals.
You can view the slide show by connecting the camera to an external monitor.
To start the slide show, press the Start menu button.
Movie file, Voice file and GIF file won't be displayed.
1. Select an image that you want to enlarge and
press the enlargement button.
2. Different parts of the image can be viewed by
using the smart button.
3. Pressing the thumbnail button will zoom back to
the original full sized image.
- You can tell whether the image displayed is an
enlarged view by checking the image
enlargement indicator shown at the top left of
the LCD monitor. (If the image is not an
enlarged view, the indicator will not be
displayed.) You can also check the area of
enlargement.
- Movie clips and WAV files can’t be enlarged.
- If an image is enlarged, a loss of quality may occur.
100-0001
x1.20
ISO : 80
Av : F3.5
Tv : 1/50
FLASH : OFF
3648X2736
2007.02.01
OFF
ƃ Configure slide show effects : Unique screen effects can be used in the slide
show.
ƃ The maximum enlargement rate in proportion to the image size.
Image size
10M
9MP
7M
7MW
5M
3M
1M
Maximum enlargement rate X11.40 X8.14 X9.80 X8.14 X8.39 X7.00 X3.20
ŝ48Ş
Starting the slide show
: The image slides regularly
(from Effect 1 to Effect 3).
: Image moves from the top left.
: Image is displayed slowly from the center
outwards.
: The next image overspreads the previous
image.
Mix
Effect 3
Effect 2
Effect 1
Off
Starting the slide show
Protecting images
ƃ Setting play interval : Set the slide show play interval
to the number of seconds preferred.
10 sec
5 sec
ƈ This is used to protect (Lock) specific shots from being accidentally erased.
It also unprotects (Unlocks) images that have been previously protected.
ONE : Protect / release displayed image.
ALL : Protect / release all saved images
3 sec
1 sec
ONE ALL
OFF
- If you protect an image, the protect icon will be
displayed on the LCD monitor. (An unprotected
image has no indicator)
- An image in LOCK mode will be protected from the
delete function, but will NOT be protected from the
format function.
ISO : 80
Av : F3.5
Tv : 1/50
FLASH : OFF
3648X2736
2007.02.01
ƃ Repeat Option : Selecting the repeat option for the slide show.
[ONE PLAY]
: The slide show is closed after
one cycle.
[REPEAT PLAY] : The slide show is repeated
until cancelled.
REPEAT PLAY
ONE PLAY
OFF
ŝ49Ş
Deleting images
DPOF
ƈ This is used to delete the displayed image.
YES : deletes displayed or checked (
) image.
NO : cancels deleting displayed image or checked
(
) image.
- The protected images can’t be deleted.
- If you wish to delete multi-image, check to delete
the image by using the (
) button and the smart
button (horizontal) and then press the [Yes] menu.
- The number of images will display right bottom of
the LCD monitor.
ŝ50Ş
Delete?
YES
NO
ƈ DPOF (Digital Print Order Format) allows you to embed printing information on
your memory card’s MISC folder. Select the pictures to be printed and how
many prints to make.
ƈ The DPOF indicator will display on the LCD monitor when an image that has
DPOF information plays back. Images can then be printed on DPOF printers,
or at an increasing number of photo labs.
ƈ This function is not available for Movie clips and Voice recording files.
ƈ If a memory card is not inserted, the menus are still displayed in the LCD, but
are not selectable.
DPOF : STANDARD
DPOF : Print size
ƈ This function allows you to embed print quantity information on a stored image.
1. Select the DPOF menu by pressing the smart
button.
2. Select a desired sub menu by pressing the smart
button.
[ONE PIC] : Select a number of prints of
displayed image.
[ALL PICS] : Configure number of prints for all
pictures except movie and voice
files.
[CANCEL] : Cancel the print setup.
3. Press the OK button to confirm the setting. If an
image carries DPOF instructions, the DPOF
indicator (
) will show.
ƈ You can specify the print size when printing images stored on the memory card.
The [SIZE] menu is available only for DPOF 1.1 compatible printers.
ƃ Setting the Print Size
1. Select the [SIZE] menu by pressing the smart
button.
2. Select a desired sub menu by pressing the smart
button.
[ONE PIC] : Select a print size of displayed
image.
[ALL PICS] : Change print size of all saved
images.
[CANCEL] : Cancel all of the print size settings.
3. Press the OK button to confirm the setting.
If an image carries DPOF instructions, the DPOF
indicator will show.
ISO : 80
Av : F3.5
Tv : 1/50
FLASH : OFF
3648X2736
2007.02.01
100-0001
00 Images
100-0001
Cancel
ſ DPOF [SIZE] secondary menu : Cancel, 3X5, 4X6, 5X7, 8X10
ſ Depending on the manufacturer and printer model, cancelling the printing
may take a little longer for the printer to process.
ŝ51Ş
DPOF : Index
Rotating an image
ƈ Images (except for movie clips and voice file) are printed as index type.
1. Select the [INDEX] menu by pressing the smart
button.
2. Select a desired sub menu by pressing the smart
button.
If [NO] is selected : Cancel the index print setting.
If [YES] is selected : The image will be printed in
index format.
NO
YES
ƈ You can rotate the stored images by various
degrees. Once the playback of the rotated picture is
finished, it will be saved in its rotated state.
1. Press the [Edit] button.
2. Press the [ROTATE] menu button.
3. Select a desired sub menu by pressing the
smart button.
100-0151
100-0
151
ROTATE
180ŭ
LEFT 90ŭ
RIGHT 90ŭ
[Before rotating the image]
[Right 90°]
[Left 90°]
[180°]
4. If you display the rotated image on the LCD monitor, empty spaces may
appear to the left and right of the image.
ŝ52Ş
Resize
ƈ Change the resolution (size) of pictures taken.
Select [User image] to save an image to be the
start-up image. The resized image will have a new
file name.
100-0151
100-0
151
INFORMATION
RESIZE
1. Press the smart button (horizontal).
2. Press the [RESIZE] menu button.
3. Select a desired sub menu by pressing the smart
button.
START IMAGE
1M 1024X768
3M 2240X1680
5M 2688X2016
7M 3136X2352
ƃ You can change the resolution of only those files compressed in the JPEG
4:2:2 format.
ƃ The resized image will have a new file name. The [START IMAGE] image is
stored not on the memory card but on the internal memory.
ƃ Only one [START IMAGE] image can be saved. If you save a new
[START IMAGE], the existing startup image will be deleted.
ƃ If the memory capacity is insufficient to store the resized image, a [Memory
Full!] message will display on the LCD monitor and the resized image will
not be stored.
ƃ Image Resize Types
Size
3136X2352 2688X2016 2240X1680
1024X768 START IMAGE
10M
O
O
O
O
O
7M
X
O
O
O
O
5M
X
X
O
O
O
3M
X
X
X
O
O
1M
X
X
X
X
O
Size
3264X2176
2752X1832
2176X1456
1280X856
9M(3:2)
O
O
O
O
Size
2688X1512
1920X1080
1344X760
7M(16:9)
O
O
O
ŝ53Ş
Trimming
Effect
ƈ By using the camera’s digital processor, it is possible to add special effects to
your images.
1. Press the [Edit] button.
2. Press the [EFFECT] menu button.
3. Select a desired sub menu by using the smart button.
ƈ You can extract part of the image that you want and save it separately.
1. Select an image that you want to enlarge.
2. Press the [Edit] button.
3. Press the [Trim] menu button.
4. Enlarge the image by using the Zoom button.
To move the image, use the Smart button.
5. Press the smart button to display a confirmation
window.
6. Press the [Yes] button. The trimmed image will
save as a new file name, and display on the LCD
monitor.
ſ If there is not enough memory space to save the
trimmed image, the image can't be trimmed.
ŝ54Ş
100-0151
100-0
151
TRIM
X1.38
Trim:
Cancel:BACK
: Captured images will be stored in black and
white.
: Captured images will be stored in a sepia tone
(a range of yellowish brown colours).
: Captured images will be stored in a blue tone.
: Captured images will be stored in a red tone.
: Captured images will be stored in a green tone.
: Save the image in negative mode.
RED
BLUE
SEPIA
B&W
Motion GIF
ƈ You can make Motion GIF with captured images.
Motion GIF : Taking images continuously and save them in a file. This file
supports animation.
ƃ How to play back the Motion GIF file
1. Select a Motion GIF file by using the smart button.
2. Press the [Play] button and menus display.
3. Press the start menu button.
ƃ How to make the Motion GIF
1. Press the [Edit] button.
2. Press the Motion GIF menu button.
100-0001
ISO : 80
Av : F3.5
Tv : 1/50
FLASH : OFF
3648X2736
2007.02.01
M.GIF
Red eye fix
3. Select the image size and FPS (Frame Per
Second).
4. Select desired images by using the smart button.
Select:
ƈ When a shot with "red eye" is played back, pressing this button can remove the
red eye from the subject.
1. Select a picture that has red eye.
2. Press the [Edit] button.
3. Press the [Red Eye Fix] menu button.
To remove the red-eye effect automatically.
4. When you press the OK button the red-eye fixed image will save as a new file
name.
5. Press the OK button and a Motion GIF file is saved.
OK
RED EYE FIX
Save:OK
Exit:BACK
ŝ55Ş
PictBridge
ƈ You can use the USB cable to connect this camera to a printer that supports
PictBridge (sold separately) and print the stored images directly. Movie clips
and voice files cannot be printed.
ƃ Setting up the camera for connection to a printer
1. Connect the camera to a printer’s USB port
with the supplied USB cable.
2. Select the [Printer] menu by using the smart
button.
USB?
Computer
Printer
ſ If you selected [Computer], when you connected the camera to your printer, the
[Connecting Computer] message will display and the connection will not be
established. Select [Printer] menu, when you connect the camera to your printer.
But, the camera may not connect to the printer, depending on the manufacturer
and model of the printer
ƈ Easy printing : When you connect the camera to printer in the Play back mode,
you can print a picture easily with the default print settings.
1. In the play back mode, connect the camera and
the printer. The menu icons will display as
shown.
2. Press the
button.
3. Select the [Yes] menu and the image will print.
Print?
Yes
No
ƈ Print mode : You can select the Easy printing mode
or Custom printing mode.
: Custom Printing mode
: Easy Printing mode
ŝ56Ş
PictBridge
ƈ Custom Set : You can select the Paper Size, Print Format, Paper Type, Print
Quality, Date Print, and File Name Print menus for printed
pictures.
ſ Some menu options are not supported on all printers.
If not supported, the menus are not displayed in the LCD.
ſ If the setting values are not changed in the automatic / manual setting, the
setting values are automatically kept.
100-0001
ƈ Printing images (Custom mode) : Images will be printed with changed printer
setting.
1. In custom printing mode, press the Print menu
button.
‫ڹ‬
No.
1
2
3
4
5
6
7
Icon
‫ڻ ں‬
‫ڼ‬
‫ھ ڽ‬
‫ڿ‬
Description
Menu
Selecting images for printing
One Pic, All Pics
Setting the size of the printing Auto, PostCard, Card, 4x6, L,
2L, Letter, A4, A3
paper
Setting the number of pictures to Auto, Full, 1, 2, 4, 8, 9, 16,
be printed on a sheet of paper
Index
Setting the quality of the
Auto, Plain, Photo, FastPhoto
printing paper
Setting the quality of the
Auto, Draft, Normal, Fine
picture to be printed
Setting whether to print the date
Auto, Off, On
Setting whether to print the file
Auto, Off, On
name
ſ You can use Print menu button after select
picture.
Print?
Yes
No
2. Select the [Yes] menu.
Print?
Yes
No
3. The screen shown on the right will appear and
the picture will be printed. If no picture is
selected, the [No Image!] message will be
displayed. Press the BACK button while printing
to cancel the printing.
Now Printing
0001 / 0001
Cancel:BACK
ŝ57Ş
PictBridge
ƈ Reset : Initialises user-changed configurations.
- In custom printing mode, press the Reset menu
button.
Setup menu
ƈ In this mode, you can set up basic settings. You can use the setup menu in all
camera modes, except Voice Recording mode.
The items indicated by
are default settings.
Menu tab
Main menu
Sub menu
Secondary menu
OSD set
(Recording mode)
Full
Basic
Hide
LCD Save
OSD set
(Playback mode)
Full
Basic
Hide
-
Series
Reset
File
ENGLISH
DEUTSCH
Language
DANSK
Page
p.60
p.60
p.60
FRANÇAIS
ESPAÑOL
ITALIANO
PORTUGUÊS
DUTCH
SVENSKA
SUOMI
p.61
BAHASA
Date&Time
Imprint
LCD
ŝ58Ş
POLSKI
Magyar
-
-
2007/02/01
yy/mm/dd
mm/dd/yy
dd/mm/yy
Off
Off
Date
Date &Time
-
Dark
Normal
Bright
-
p.61
p.61
p.61
AF Lamp
Off
On
p.62
Power Off
1, 3, 5, 10 min
-
p.62
Quick View
Off
0.5, 1, 3 sec
p.62
Setup menu
Menu tab
Main menu
Start Image
Sound Volume
Beep Sound
Start Sound
Shutter Sound
Format
Delete All
Copy to Card
Video Out
Reset
Sub menu
Off
User image
Off
Medium
Off
Sound2
Off
Sound2
Off
Sound2
No
No
No
NTSC
No
Secondary menu
LOGO
Low
High
Sound1
Sound3
Sound1
Sound3
Sound1
Sound3
Yes
Yes
Yes
PAL
Yes
Page
p.62
ƈ How to select the setup menu
1. In any mode with the exception of Photo Gallery
mode, press the extension menu button (
)
and press the setup menu button (
).
p.63
p.63
p.63
p.63
2. Each buttons have different setup menus.
Press the F1-4 (
) menu button.
Full Ȝ
Basic
OSD Set
OSD Set
Hide
File
LCD Save
Language
Date&Time
Exit:BACK
p.63
p.64
p.64
p.65
p.65
ſ Menus are subject to change without prior notice.
ŝ59Ş
Setup menu
[OSD set]
[ File name ]
ƈ You can check shooting (Recording mode) and displayed image (Play back
mode) information.
ƈ This function allows the user to select the file naming format.
Full Ȝ
OSD Set
OSD Set
OSD Set
Hide
File
LCD Save
Language
Language
Date&Time
Date&Time
Exit:BACK
[Recording mode menu]
[Full]
Full
Basic Ȝ
Basic
Hide
OSD Set
File
Exit:BACK
[Play back mode menu]
: When the smart button is touched, the icons will be enlarged and
OSD will be displayed.
[Basic] : When the smart button is touched, the icons will be enlarged and
OSD will not be enlarged.
[Hide] : If the camera doesn't operate for about 3 seconds, all OSD will
disappear. When the shutter is pressed down or half way down, the
shutter speed and auto focus frame will display. OSD may display by
using the camera buttons except for the shutter button.
[LCD save] : If the camera is not used for about 30 seconds, the power and
camera status lamps blink and the LCD monitor turns off.
(LCD save is only applied to the Recording mode menu.)
ŝ60Ş
[Series] : New files are named using numbers that
Series
OSD Set
Reset
OSD Set
follow the previous sequence, even when
File
Ȝ
a new memory card is used, or after
Language
formatting, or after deleting all pictures.
Date&Time
[Reset] : After using the reset function, the next file
Exit:BACK
name will be set from 0001 even after
formatting, deleting all or inserting a new
memory card.
- The first stored folder name is 100SSCAM, and the first file name is
SNV10001.
- File names are assigned sequentially from SNV10001 ƍ SNV10002 ƍ ~ ƍ
SNV19999.
- The folder number is assigned sequentially from 100 to 999 as follows:
100SSCAM ƍ 101SSCAM ƍ ~ ƍ 999SSCAM.
- The files used with the memory card conform to the DCF (Design rule for
Camera File systems) format.
- File names assigned in the Biz mode, will be set SB1ZXXXX
Setup menu
[ Language ]
[ Imprinting the recording date ]
ƈ There is a choice of languages that can be displayed on the LCD monitor.
Even if the battery and AC charger are removed and inserted again, the
language setting will be preserved.
ƈ There is an option to include DATE / TIME on still images.
LANGUAGE sub menu :
English, Korean, French, German, Spanish, Italian,
S.Chinese, T.Chinese, Japanese, Russian,
Portuguese, Dutch, Danish, Swedish, Finnish, Thai,
BAHASA (MALAY / INDONESIAN), Arabic, Polish,
Hungarian, Czech and Turkish.
ENGLISH
OSD Set
OSD Set
FRANÇAIS
File
DEUTSCH Ȝ
ह
Language
Date&Time
Exit:BACK
ƃ Sub menus
[Off]
: The DATE & TIME will not be imprinted
on the image file.
[Date]
: Only the DATE will be imprinted on the
image file.
[Date&Time]: The DATE & TIME will be imprinted on
the image file.
Off Ȝ
Imprint
Date
LCD
Date&Time
AF Lamp
Power Off
Quick View
Exit:BACK
ſ The Date & Time are imprinted at the bottom right side of the still image.
ſ The imprint function is applied only to still images except for the images
taken in the [Text] scene mode and photo frame effect mode.
ſ Depending on the manufacturer and print mode, the date printed on an
image may not be printed correctly.
[ Setting up the Date / Time / Date type ]
[ LCD brightness ]
ƈ You can change the date and time that will be displayed on the captured
images and set up the date type.
- Date type : [yy/mm/dd], [mm/dd/yy], [dd/mm/yy],
[Off]
Ȝ
ƈ You can adjust the LCD brightness.
2007/02/01
OSD Set
yy/mm/dd
OSD Set
ƃ [LCD] sub menu : Dark, Normal, Bright
Dark
Normal Ȝ
Imprint
LCD
mm/dd/yy
File
dd/mm/yy
Language
Power Off
Date&Time
Quick View
Exit:BACK
Exit:BACK
Off Ȝ
Bright
AF Lamp
ŝ61Ş
Setup menu
[ Auto Focus lamp ]
[ Quick view ]
ƈ You can turn the Auto Focus lamp on and off.
ƈ If you enable Quick View before capturing an image, you can view the image
you just captured on the LCD monitor for the duration set in the [Quick View]
setup. Quick view is possible only with still images.
ƃ Sub menus
[Off] : The AF lamp will not light up in a low light
condition.
[On] : The AF lamp will light up in a low light
condition.
Off
Imprint
On
LCD
Ȝ
AF Lamp
Power Off
Quick View
Exit:BACK
ƃ Sub menus
[Off]
: The quick view function can’t be
activated.
[0.5, 1, 3 sec] : The captured image is briefly
displayed during the selected time.
Off
Imprint
0.5 sec
LCD
1 sec
AF Lamp
3 sec
Power Off
Ȝ
Quick View
Exit:BACK
[ Auto power off ]
[ Start up image ]
ƈ This function switches the camera off after a set amount of time in order to
prevent unnecessary battery drainage.
ƈ You can select the image that is first displayed on the LCD monitor whenever
the camera is turned on.
ƃ Sub menus
[1, 3, 5, 10 min]: The power will turn off automatically
if not used for the period of time
specified.
1 min
Imprint
3 min
LCD
5 min
AF Lamp
10 min Ȝ
Power Off
Quick View
- After replacing the battery, the power off setting
Exit:BACK
will be preserved.
- Note that the automatic power off function will not
operate if the camera is in PC connect print, slide
show, playing back a voice recording, playing back a movie file, playing back
a GIF file, recording a movie clip or taking a composite shot.
ŝ62Ş
ƃ Start up image : [Off], [LOGO], [User Image]
- Use a saved image for the start-up image with the
[START IMAGE] in the [RESIZE] menu in the play
mode.
- The start-up image will not be deleted by [DELETE]
or [Format] menu.
- The User images will be deleted by [Reset] menu.
Off Ȝ
LOGO
User image
Start Image
Sound Volume
BEEP Sound
Start Sound
Shutter Sound
Exit:BACK
Setup menu
[ Sound Volume ]
[ Shutter sound ]
ƈ You can select the sound volume levels of start sound, operation sound and
shutter sound.
ƈ You can select the shutter sound.
ƃ [Sound Volume] sub menus : [Off], [Low],
[Medium], [High]
Off
Low Ȝ
Start Image
ƃ Shutter sound : [Off], [Sound 1], [Sound 2],
[Sound 3]
Off
Start Image
Sound 1
Sound Volume
Sound Volume
Sound 2
Medium
BEEP Sound
Sound 3
High
Start Sound
BEEP Sound
Start Sound
Ȝ
Shutter Sound
Shutter Sound
Exit:BACK
Exit:BACK
[ Operation Sound ]
ƈ If you set sound to ON, various sounds will be activated for camera startup,
when buttons are pressed, so that you can be aware of the camera operation
status.
ƃ [Sound] sub menus : [Off], [Sound 1], [Sound 2],
[Sound 3]
- If you set sound to [Off], various sounds will not
be activated.
Off
Start Image
Sound 1
Sound Volume
Sound 2 Ȝ
Sound 3
BEEP Sound
Start Sound
Shutter Sound
Exit:BACK
[ Start up sound ]
ƈ You can select the sound that is activated whenever the camera is turned on.
ƃ Start up sound : [Off], [Sound 1], [Sound 2],
[Sound 3]
Off
Start Image
Sound 1
Sound Volume
Sound 2
BEEP Sound
Sound 3 Ȝ
Start Sound
Shutter Sound
Exit:BACK
[ Formatting a memory ]
ƈ This is used for formatting the memory. If you run [Format] on the memory, all
images, including the protected images, will be deleted. Be sure to download
important images to your PC before formatting the memory.
ƃ Sub menus
[No] : The memory will not be formatted.
No Ȝ
Format
Yes
Delete All
[Yes] : A confirmation window will display. Select the
Copy to Card
[Yes] menu by pressing the smart button.
Video Out
A [Processing!] message appears and the
Reset
memory will be formatted. If you run FORMAT
Exit:BACK
in Play mode, a [No Image!] message will
appear.
Be sure to run [Format] on the following types of memory card.
- A new memory card, or an unformatted memory card
- A memory card that has a file this camera can't recognise or one that has
been taken from another camera.
INFORMATION
ƃ Always format the memory card using this camera. If you insert a memory
card that has been formatted using other cameras, memory card readers, or
PCs, you will get a [Card Error!] message.
ŝ63Ş
Setup menu
[ Delete All ]
[ Copy To Card ]
ƈ Of all the files stored in the memory card, the unprotected files in the DCIM
subfolder will be deleted.
ƈ This enables you to copy image files, movie clips and voice recording files to
the memory card.
[No] : Cancel the "Delete All".
[Yes] : A confirmation window will display. Select the
[Yes] menu by pressing the smart button. A
[Processing!] message appears and the
unprotected files in the DCIM subfolder will
be deleted.
No
Yes Ȝ
Format
Delete All
Copy to Card
Video Out
Reset
[No] : Cancels "Copy to Card".
[Yes] : All images, movie clips and voice recording
files saved in the internal memory are
copied to the memory card after the
[Processing!] message is displayed.
No
Format
Yes
Delete All
Ȝ
Copy to Card
Video Out
Reset
Exit:BACK
Exit:BACK
INFORMATION
INFORMATION
ƃ The protected images can’t be deleted.
ƃ If there aren’t any protected images, all images are deleted and a
[No Image!] message will display in the Play mode.
ŝ64Ş
ƃ When this menu is selected without inserting a memory card, you can
select the [Copy To Card] menu but the menu can’t be run.
ƃ If there is not enough space available in the memory card to copy saved
images in the internal memory (20MB), the [Copy To Card] command will
copy only some of the images and display [Memory Full!] message. Then
the system will return to the playback mode. Please be sure to delete any
unnecessary files in the internal memory to free up space before inserting
the memory card into the camera.
ƃ When you move the images that are stored in the internal memory to the
memory card, the next number of file names will be created in the card to
avoid duplication of the file name.
- When the [Reset] of the [File] setup menu is set : The copied file names
start from after the last stored file name.
- When the [Series] of the [File] setup menu is set : The copied file names
start from after the last captured file name. After completing [Copy To
Card], the last stored image of the last copied folder is displayed on the
LCD monitor.
Setup menu
[ Selecting Video out type ]
ƈ The Movie output signal from the camera can be NTSC or PAL.
Your choice of output will be governed by the type of device (monitor or TV,
etc.) to which the camera is connected. PAL mode can support only BDGHI.
ƈ Connecting to an external monitor
In RECORDING/ PLAY mode, you can view the
stored still images or movie clips by connecting the
camera to an external monitor via the AV cable.
When the camera is connected to an external
monitor, the LCD monitor will be turned off
automatically.
NTSC
Format
PAL
Delete All
Copy to Card
Ȝ
Video Out
Reset
Exit:BACK
- When using a TV as an external monitor, you will need to select the external
or AV channel of the TV.
- There will be a digital noise on the external monitor, but it is not a malfunction.
- If the image is not in the centre of the screen, use the TV controls to centre it.
- When the camera is connected to an external monitor, some parts of the
image may not display.
- When the camera is connected to an external monitor, the menu will be
visible on the external monitor and the menu functions are the same as those
indicated on the LCD monitor.
- When the camera is connected to an external monitor, the button sound may
not sound.
[ Initialisation ]
Yellow - Video
White - sound
- NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico.
- PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany,
U.K., Holland, Italy, Kuwait, Malaysia, New Zealand, Singapore,
Spain, Sweden, Switzerland, Thailand, Norway.
ƈ All camera menu and function settings will be restored to their default values.
However, values for DATE / TIME, LANGUAGE, and VIDEO OUT will not be
changed.
ƃ Sub menus
[No] : Settings will not be restored to their defaults.
[Yes] : A confirmation window will display. Select
the [Yes] menu by pressing the smart button.
All settings will be restored to their defaults.
No
Format
Yes
Delete All
Copy to Card
Video Out
Ȝ
Reset
Exit:BACK
ŝ65Ş
Important notes
Be sure to observe the following precautions!
ƈ This unit contains precision electronic components. Do not use or store this
unit in the following locations.
- Areas exposed to severe changes in temperature and humidity.
- Areas exposed to dust and dirt.
- Areas exposed to direct sunlight or the inside of a vehicle in hot weather.
- Environments where there is high magnetism or excessive vibration.
- Areas with high explosives or highly flammable materials.
ƈ Do not leave this camera in places subject to dust, chemicals (like
naphthalene and mothball), high temperatures or high humidity.
Keep this camera with silica gel in a hermetically sealed box when not
planning to use the camera for a long period of time.
ƈ Sand can be particularly troublesome to cameras.
- Do not let sand get inside the camera when using it on beaches, coastal
dunes, or other areas where there is lots of sand.
- Doing so may result in failure or may render the camera permanently unusable.
ƈ Handling the camera
- Never drop the camera or subject it to severe shocks or vibrations.
- Protect the large size LCD monitor from an impact. When this camera is not
used, keep it in the camera case.
- Avoid obstructing the lens or the flash when you capture an image.
- This camera is not waterproof.
To avoid dangerous electrical shocks, never hold or operate the camera with
wet hands.
- If you use this camera in wet places, such as beach or pool, do not let water
or sand get inside the camera. Doing so may result in failure or may
permanently damage the unit.
ŝ66Ş
ƈ Extremes in temperature may cause problems.
- If the camera is transferred from a cold to a warm and humid environment,
condensation can form on the delicate electronic circuitry. If this seems likely,
wait for at least 1 hour until all moisture is dispersed before attempting to use
the camera.
Moisture built up can also occur on the memory card. If this happens, turn off
the camera and remove the memory card. Wait until the moisture has
dispersed.
ƈ Caution on Using the Lens
- If the lens is subjected to direct sunlight, it could result in the discoloration
and deterioration of the image sensor.
- Avoid getting fingerprints or foreign substances on the surface of the lens.
ƈ If the digital camera is not used for a long period, an electric discharge can
occur.
It is a good idea to remove the battery and the memory card if you do not
intend using the camera for an extended period of time.
ƈ If the camera is exposed to an electronic interference, it will turn itself off to
protect the memory card.
Important notes
ƈ Camera Maintenance
- Use a soft brush (available from photo stores) to gently clean the lens and
LCD assemblies. If this does not work, lens-cleaning paper with lens cleaning
fluid can be used.
Clean the camera body with a soft cloth. Do not allow this camera to come
into contact with solvent materials such as benzol, insecticide, thinners etc.
This may damage the body shell of the camera and also affect its
performance. Rough handling can damage the LCD monitor. Take care to
avoid damage and keep the camera in a protective carrying case when not in
use.
ƈ Do not attempt to disassemble or modify the camera.
ƈ Under certain conditions, static electricity can cause the flash unit to fire. This
is not harmful to the camera and is not a malfunction.
ƈ When images are uploaded or downloaded, the data transfer may be affected
by static electricity.
In this case, disconnect and re-connect the USB cable before trying the
transfer again.
ƈ Always check the condition of the camera before an important event or going
on a trip.
- Take a picture to check that the camera is working correctly and ensure you
have a fully charged spare battery.
- Samsung cannot be held responsible for camera malfunctions.
Warning indicator
ƈ There are several warnings that may appear on the LCD display
Memory Error!
ϛMemory card error
ƍ Turn off the camera power and turn it on again
ƍ Insert the memory card again
ƍ Insert and format the memory card (p.63)
Card Locked!
ϛThe memory card is locked
ƍ SD/SDHC/MMC memory card : Slide the write protect switch towards the
top of the memory card
No Card!
ϛA memory card is not inserted
ƍ Turn off the camera power and insert the memory card again
ƍ Turn off the camera power and turn it on again
No Image!
ϛThere are no images stored on the memory
ƍ Take images
ƍ Insert a memory card that is holding some images
File Error!
ϛFile error
ƍ Delete the erroneous files.
ϛMemory card error
ƍ Contact a camera service centre
ŝ67Ş
Warning indicator
Low Battery!
ϛThere is low battery capacity
ƍ Insert a fully charged battery.
Low Light!
ϛWhen taking pictures in dark places
ƍ Take pictures in Flash Photography mode.
DCF Full Error
ϛViolation of DCF format
ƍ Copy the images to a PC and format the memory.
Before contacting a service centre
ƈ Please check the following
The camera doesn’t switch on
ϛThere is low battery capacity
ƍ Insert a fully charged battery. (p.13)
ϛBattery is inserted incorrectly with the polarities reversed.
ƍ Insert the battery according to the polarity marks (+, -)
ϛThe rechargeable battery is not inserted
ƍ Insert the battery and turn on the camera
The camera power ceases while in use
ϛThe battery is exhausted
ƍ Insert a fully charged battery.
ϛThe Camera is turned off automatically
ƍ Turn on the camera power again.
ŝ68Ş
Battery power quickly drains
ϛThe Camera is being used in low temperatures
ƍ Keep the camera in warm conditions (i.e. inside a coat or jacket) and only
remove it in order to take images
Camera does not take images when pressing the Shutter button
ϛThere is insufficient memory capacity
ƍ Delete unnecessary image files
ϛThe memory card has not been formatted
ƍ Format the memory card (p.63)
ϛThe memory card is exhausted
ƍ Insert a new memory card
ϛThe memory card is locked
ƍ Refer to [Card Locked!] error message (p.67)
ϛThe cameraŖs power is off
ƍ Turn the camera power on
ϛThe battery is exhausted
ƍ Insert a fully charged battery. (p.13)
ϛBattery is inserted incorrectly with the polarities reversed.
ƍ Insert the battery according to the polarity marks (+, -)
The camera suddenly stops working while in use
ϛThe camera stopped due to a malfunction
ƍ Remove /re-insert battery and switch the camera on
Before contacting a service centre
The images are unclear
ϛA picture was taken the subject without setting an appropriate macro mode
ƍ Select an appropriate macro mode to take a clear image.
ϛTaking a picture beyond the flash range
ƍ Take a picture within the flash range
ϛThe lens is smudged or dirty
ƍ Clean the lens
Colour of image is different to the original scene
ϛWhite balance or effect setting is incorrect
ƍ Select appropriate White balance and effect
The flash does not fire
ϛFlash off mode has been selected
ƍ Dis-engage flash off mode
ϛThe camera mode can't use flash
ƍ Refer to the FLASH instruction (p.30)
No image on external monitor
ϛThe external monitor has not been connected properly with the camera
ƍ Check the connection cables
ϛThere are incorrect files in the memory card
ƍ Insert a memory card that has correct files
Incorrect date and time is displayed
ϛThe date and time have been set incorrectly or the camera has adopted the
default settings
ƍ Reset the date and time correctly
When using the PC’s explorer, the [Removable Disk] file does not show
ϛCable connection is incorrect
ƍ Check the connection
ϛThe camera is off
ƍ Turn the camera on
ϛThe operating system is not Windows 98SE, 2000, ME, XP, Vista/ Mac OS
Mac OS 9.0 ~ 10.4. Alternatively the PC does not support USB
ƍ Install Windows 98SE, 2000, ME, XP, Vista/ Mac OS 9.0 ~ 10.4 to PC that
supports USB
ϛThe camera driver is not installed
ƍ Install a [USB Storage Driver]
The camera buttons do not operate
ϛCamera malfunction
ƍ Remove/re-insert battery and switch the camera on
A card error has occurred while the memory card is in the camera.
ϛIncorrect memory card format
ƍ Re-format the memory card
Images are too bright
ϛExposure is excessive
ƍ Reset exposure compensation
The images don't play back
ϛIncorrect file name (Violation of DCF format)
ƍ Do not change the image file name
ŝ69Ş
Specifications
ƈ Image Sensor
- Type : 1/1.8ůCCD
- Effective Pixel : Approx. 10.1 Mega-pixel
- Total Pixel : Approx. 10.3 Mega-pixel
ƈ Lens
- Focal Length : Schneider Lens f = 7.8 ~ 39mm
(35mm film equivalent : 38~190mm)
- F No. : F2.8 - F4.4
- Digital Zoom : · Still Image mode : 1.0X ~ 5.0X
· Play mode : 1.0X ~ 11.4X (depends on image size)
ƈ LCD Monitor : 2.7" color TFT LCD (230,000 pixel)
ƈ Effect : Normal, B&W, Sepia, Red, Green, Blue, Negative, Custom RGB
Focus Type
Wide(W)
Tele(T)
Normal
80cm-Infinity
1.5m~Infinity
Macro
10cm~80cm
50cm~80cm
Auto Macro
10cm-Infinity
50cm-Infinity
Super Macro
1~10cm (Wide only)
1cm-Infinity
ƈ Shutter
- Speed : Auto : 1 ~ 1/2,000 sec.
Manual, S Mode : 15 ~ 1/2,000 sec.
Night : 15 ~ 1/2,000 sec.
Fireworks : 4 sec.
ŝ70Ş
ƈ Flash
- Modes : Auto, Auto & Red-eye reduction, Fill-in flash, Slow sync, Flash off,
Red-eye Fix
- Range : 0.3~4.9m (Wide), 0.5~3.0m (Tele)
- Recharging Time : Approx. 5 sec.
ƈ Sharpness : Soft, Normal, Vivid
ƈ Focusing
- Type : TTL auto focus, Manual Focus
- Range
Manual Focus
ƈ Exposure
- Control : Program AE, Shutter Priority AE, Aperture Priority AE or Manual
Exposure
- Metering : Multi, Center weighted, Spot
- Compensation : ±2EV (1/3EV steps)
- ISO Equivalent : Auto, 80, 100, 200, 400, 800, 1600
50cm-Infinity
ƈ White Balance : Auto, Daylight, Cloudy, Fluorescent_H, Fluorescent_L,
Tungsten, Custom 1,2
ƈ Voice Recording : Voice Recording (Max 10 hour)
Voice Memo in Still Image (Max. 10 sec.)
ƈ Date Imprinting : Date&Time, Date, Off (user selectable)
ƈ Shooting
- Still Image : · Modes : Auto, Program, A/S/M, Scene, ASR, Effect
· Scene : Night, Portrait, Children, Landscape, Biz, Close-up,
Text, Sunset, Dawn, Backlight, Fireworks, Beach &
Snow
· Continuous : Single, Continuous, High Speed, AEB
Motion Capture : 7fps up to 20 shots
· Self-timer : 2 sec., Double, 10 sec., Remocon (optional)
Specifications
- Movie Clip : · With Audio (recording time : memory capacity dependent, Max. 4GB)
· Size : 640x480, 320x240
· Frame rate : 30 fps, 15 fps
· 5X Optical Zoom and Mute in Zooming
ƈ Storage
- Media :
· Internal Memory : About 20MB
· External Memory (Optional) : SD, MMC(Plus)(2GB
guaranteed)/SDHC Card
(up to 4GB guaranteed)
* Internal Memory capacity is subject to change without prior
notice.
- File Format : · Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.0
· Movie : AVI (MPEG-4)
· Audio : WAV
- Image Size
10M
9M P
7M
7M W
5M
3M
1M
3648X
2736
3648X
2432
3136X
2352
3648X
2056
2688X
2016
2240X
1680
1024X
768
10M
49
94
136
ƈ Interface
- Digital output connector : USB 2.0
- Audio : Mono
- Video output : NTSC, PAL (user selectable)
- DC power input connector : 24pin Connector
ƈ Power Source
- Rechargeable battery : 3.7V Li-ion battery (SLB-1137D)
- Adaptor : SAC-45
* Included battery may depending on sales region.
ƈ Dimensions (WxHxD) : 106.6x64.2x21.9mm
ƈ Weight : 195.3g (without batteries and card)
ƈ Operating Temperature : 0 ~ 40ŭC
ƈ Operating Humidity : 5 ~ 85%
- Capacity (256MB MMC)
Super Fine
Fine
Normal
ƈ Image Play
- Type : Single image, Thumbnails, Slide show, Movie Clip
- Editing : Trimming, Resizing, Rotate, Color Effect, GIF Animation, Red-eye
Fix
9M P
55
105
151
7M
65
124
177
7M W
64
122
174
5M
87
163
228
3M
122
221
303
1M
419
617
733
* These figures are measured under Samsung’s standard conditions and may
vary depending on shooting conditions and camera settings.
ƈ Software
- Application : Digimax Master, Digimax Biz Reader
Adobe Reader
ſ Specifications are subject to change without prior notice.
ſ All trademarks are the property of their respective owners.
ŝ71Ş
Software Notes
About the software
Please ensure that you read this instruction manual carefully before use.
ҮThe attached software is a camera driver and image editing software tool for
Windows.
ҮUnder no circumstances should all or part of either the software or the user
manual be reproduced.
ҮCopyrights for software are licensed only for use with a camera.
ҮIn the unlikely event of a manufacturing fault, we will repair or exchange your
camera.
We cannot, however, be held responsible in any way for damage caused by
inappropriate use.
ҮUsing a Hand-made (self assembled) PC or a PC and OS that has not been
guaranteed by the manufacturer is not covered by the Samsung warranty.
ҮBefore using this manual, you should have a basic knowledge of computers
and O/S (Operating Systems).
System Requirements
For Windows
PC with processor better than Pentium 450MHz
(Pentium 800MHz recommended)
Windows 98SE/2000/ME/XP/Vista
For Macintosh
Power Mac G3 or later
Mac OS 9.0~10.4
Minimum 128MB RAM (512MB
recommended)
200MB of available hard disk space
(1GB recommended)
Minimum 64MB RAM
(256MB recommended)
USB port
CD-ROM drive
USB port
CD-ROM drive
1024x768 pixels, 16-bit color display compatible
monitor (24-bit color display recommended),
Microsoft DirectX 9.0
ŝ72Ş
After inserting the CD-ROM provided with this camera into the CD-ROM drive, the
following window should automatically run.
Before connecting the camera to the PC, you
should first install the camera driver.
ſScreen Captures illustrated on this manual is
based on English Edition of Windows.
ƈ Camera driver : This enables images to transfer between the camera and
PC.
This camera uses the USB Storage Driver as the camera driver. You can use
the camera as a USB card reader. After installing the driver and connecting this
camera to the PC, you can find [Removable Disk] in [Windows Explorer] or [My
Computer]. A USB Storage Driver is provided only for Windows. A USB Driver
for MAC is not included with the Application CD. You can use the camera with
Mac OS 9.0 ~ 10.4.
ƈ XviD codec : This allows movie clips (MPEG-4) recorded with this camera
to be played back on a PC.
To play back a movie clip recorded with this camera, you must install the XviD
codec. If a movie clip recorded with this camera does not play well, install this
codec. This software is only compatible with Windows.
ƈ Digimax Master : This is the all-in-one multi media software solution.
You can download, view, edit and save your digital images and movie files with
this software. This software is only compatible with Windows.
About the software
ƈDigimax Biz Reader : This is the Visiting Card Recognition software
solution.
You can recognize visiting card and edit namecards database easily with this
software. This software is only compatible with Windows.
INFORMATION
ƃ Be sure to check the system requirements before installing the driver.
ƃ To play back the movie taken with this camera on the computer, DirectX 9.0
must be installed.
ƃ You should allow 5 - 10 seconds for running the automatic setup program
according to the capability of your computer. If the frame does not show, run
the [Windows Explorer] and select [Installer.exe] in the CD-ROM Drive.
ƃ PDF documents of user manual are included in the Software CD-ROM
supplied with this camera. Search the PDF files with Window's explorer.
Before opening the PDF files, you must install the Adobe Reader included in
the Software CD-ROM.
ƃ To install the Adobe Reader 6.0.1 correctly, Internet Explorer 5.01 or later
had to be installed. Visit "www.microsoft.com" and upgrade the Internet
Explorer.
Setting up the application software
ƈ To use this camera with a PC, install the application software first.
After this has been done, the stored images in the camera can be moved to the
PC and can be edited by an image editing program.
ƈ You can visit the Samsung web-site through the internet.
http://www.samsungcamera.com : English
http://www.samsungcamera.co.kr : Korean
1. The auto run frame will display.
Click the [Install] menu in the Auto run
frame.
2. Install the camera driver and DirectX by selecting a button shown on the
monitor. If a latest version of DirectX was installed on your computer, DirectX
may not be installed.
ŝ73Ş
Setting up the application software
3. To play back a movie clip recorded with this camera on the computer, install
the XviD codec.
ſ The XviD codec is distributed according to and under the terms and conditions of
the GNU General Public License and anyone can copy, modifiy and distribute
this codec freely, but WITHOUT ANY WARRANTY, IMPLIED OR
EXPRESSED, OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE; provided, however, that you have to follow the GNU General Public
License whenever you are distributing this codec or modification thereof.
For more information see the GNU General Publice License documents
(http://www.gnu.org/copyleft/gpl.html).
ŝ74Ş
4. Install the Digimax Master in the order shown.
Setting up the application software
5. After restarting the computer, connect the PC to the camera with the USB
cable.
6. Turn on the camera power.
The [Found New Hardware Wizard] will
open and the computer will recognise the
camera.
ſ If your OS is Windows XP, an image
viewer program will open.
If the download window of Digmax Master
opens after starting Digimax Master, the
camera driver was set up successfully.
Starting PC mode
ҮIn this mode, you can download stored images to your PC through the USB
cable.
ҮThe LCD monitor is always turned off in PC mode.
ƈ Connecting the camera to a PC
1. Connect the PC to the camera with the USB cable.
2. Select the [USB]-[Computer] menu by using the
smart button.
USB?
Computer
Printer
INFORMATION
ƃ If you have installed the camera driver, The [Found New Hardware Wizard]
may not open.
ƃ On a Windows 98SE system, the Found New Hardware Wizard dialog box
opens and a window asking you to select a driver file may appear. In this
case, specify "USB Driver" in the CD supplied.
ŝ75Ş
Starting PC mode
ƈ Connecting the camera to a PC
ƈ Downloading stored images
You can download the still images stored on the camera to your PC's hard disk
and print them or use a photo editing software to edit them.
1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display, select
[My computer] and double click [Removable
Disk ƍ DCIM ƍ 100SSCAM].
The image files will then be displayed.
ſ If you selected [Printer] in Step 2, when you connect the camera to your
printer, the [Connecting Printer] message will display and the connection will
not be established.
In this case, disconnect the USB cable, and then follow the procedure from
Step 1 and onward.
3. Select an image and press the right mouse
button.
ƈ Disconnecting the camera and PC : Refer to page 77
(Removing the removable disk).
INFORMATION
ƃ Before inserting any cables or AC adapter, check the directions and do not
insert by force. It may damage the cable or camera.
4. A pop-up menu will open.
Click the [Cut] or [Copy] menu.
- [Cut] : cuts selected files.
- [Copy] : copies selected files.
5. Click a folder where you want to paste the file.
ŝ76Ş
Starting PC mode
6. Press the right mouse button and a pop-up
menu will open. Click [Paste].
7. An image file is transferred from the camera
to your PC.
Removing the removable disk
ƈ Windows 98SE
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has finished
blinking and is constantly on.
2. Unplug the USB cable.
ƈ Windows 2000/ME/XP/Vista
(The illustrations may differ from those shown depending on the Windows O/S.)
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has finished
blinking and is constantly on.
2. Double-click the [Unplug or Eject Hardware]
icon on the task bar.
[Double-click!]
3. The [Unplug or Eject Hardware] window will
open. Select the [USB Mass Storage
Device] and click the [Stop] button.
- By using [Digimax Master], you can see the stored images in the memory
directly on the PC monitor and you can copy or move the image files.
CAUTION
ƃ We recommend that you should copy the images to the PC to view them.
Opening images directly from the removable disk may be subject to
unexpected disconnection.
ƃ When you upload a file that is not taken by this camera to the Removable
Disk, the [File Error!] message will be displayed on the LCD monitor in the
PLAY mode, and nothing is displayed in THUMBNAIL mode.
4. The [Stop a Hardware device] window will
open. Select the [USB Mass Storage
Device] and click the [OK] button.
5. A [Safe to Remove Hardware] window will
open. Click the [OK] button.
ŝ77Ş
Removing the removable disk
6. A [Unplug or Eject Hardware] window will open.
Click the [Close] button and the removable disk
may be safely removed.
Removing the USB Driver for Windows 98SE
ƈ To remove the USB driver, refer to the process shown below.
1. Connect the camera to your PC and turn them on.
2. Check whether the Removable Disk is on the [My Computer].
3. Remove the [Samsung Digital Camera] on the Device manager.
7. Unplug the USB cable.
Setting up the USB Driver for MAC
1. A USB Driver for MAC is not included with the software CD as MAC OS
supports the camera driver.
2. Check the MAC OS version during start-up.
This camera is compatible with MAC OS 9.0 ~ 10.4.
3. Connect the camera to the Macintosh and turn the camera power on.
4. A new icon will be displayed on the desktop after connecting the camera to
the MAC.
4. Disconnect the USB cable.
5. Remove the [Samsung USB Driver] on the Add / Remove Programs
Properties.
Using the USB Driver for MAC
1. Double click a new icon on the desktop and the folder in the memory will be
displayed.
2. Select an image file and copy or move it to MAC.
CAUTION
ƃ For Mac OS 10.0 or later : First complete uploading from computer to
camera and then remove the removable disk
with the Extract command.
ŝ78Ş
6. Uninstallation is complete.
Digimax Master
ƈ You can download, view, edit and save your images and movies with this
software. This software is only compatible with Windows.
ƈ To start the program, click [Start ƍ Programs ƍ Samsung ƍ Digimax Master
ƍ Digimax Master].
ƃ Downloading images
1. Connect the camera to your PC.
4. Select a destination and make a folder to
save downloaded images and folders.
- Folder names can be made in order of date
and images will be downloaded.
- Folder name will be made as you want and
images will be downloaded.
- After selecting a folder that was made
before, images will be downloaded.
5. Click [Next >] button.
2. A window for downloading images will
display after connecting the camera to
your PC.
- To download the captured images,
select the [Select All] button.
- Select desired folder in the window and
click the [Select All] button. You can
save captured images and selected folders.
- If you click the [Cancel] button, downloading
will be cancelled.
6. A window will open as shown alongside.
The destination of the selected folder will be
displayed on the upper side of the window.
Click the [Start] button to download the
images.
3. Click [Next >] button.
7. Downloaded images will be displayed.
ŝ79Ş
Digimax Master
ƃ Image viewer : You can view the stored images.
‫ڹ‬
ƃ Image edit : You can edit the still image.
‫ڽ‬
‫ھ‬
‫ڹ‬
‫ڼ‬
‫ڿ‬
‫ں‬
‫ڻ‬
‫ڼ‬
‫ں‬
‫ڻ‬
- Image viewer functions are listed below.
‫ ڹ‬Menu bar : You can select menus.
File, Edit, View, Tools, Change functions, Auto download, help, etc.
‫ ں‬Image selection window : You can select the desired images in this window.
‫ ڻ‬Media type selection menu : You can select image viewer, image edit and
movie edit functions in this menu.
‫ ڼ‬Preview window : You can preview an image or a movie clip and check the
multi media information.
‫ ڽ‬Zoom bar : You can change preview size.
‫ ھ‬Folder display window : You can see the folder location of the selected
image.
‫ ڿ‬Image display window : Images in the selected folder are displayed.
ſ Refer to the [Help] menu in Digimax Master for further information.
ŝ80Ş
- Image edit functions are listed below.
‫ ڹ‬Edit menu : You can select the following menus.
[Tools] : You can resize or crop the selected image. See the [Help] menu.
[Adjust] : You can modify image quality. See the [Help] menu.
[Retouch] : You can change image or insert effects on the image. See the
[Help] menu.
‫ ں‬Drawing tools : Tools for editing an image.
‫ ڻ‬Image display window : A selected image displays in this window.
‫ ڼ‬Preview window : You can preview the changed image.
ſ A still image edited with Digimax Master can’t be played back on the camera.
ſ Refer to the [Help] menu in Digimax Master for further information.
Digimax Master
Digimax Biz Reader
ƃ Movie edit : You can get the still image, movie clip, narration, music files together
in a movie clip.
‫ڹ‬
ƈ Digimax Biz Reader is digital business card management software which
recognize the information on business card like name, company, telephone
number, e-mail and so on. It offers the more effective businesss information
management solution with digital camera.
This software is only compatible with Windows
Digimax Biz Reader recognizes English and Korean business namecard only.
ƈ Auto recognizing when camera connected with computer(BizChecker)
After installing <Biz Reader>, if you connect the SAMSUNG digital camera with
your computer, namecard images are recognized automatically.
<BizChecker> is auto-installing program when <BizReader> installing.
‫ں‬
- Movie clip edit functions are listed below.
‫ ڹ‬Edit menu : You can select the following menus.
[Add Media] : You can add other media elements to a movie.
[Edit Clip] : You can change the brightness, contrast, colour and saturation.
[Effects]
: You can insert an effect.
[Set Text] : You can insert texts.
[Narrate] : You can insert a narration.
[Produce] : You can save the edited multi media as a new file name.
You can select AVI, Windows media (wmv) and Windows
media (asf) file types.
‫ ں‬Frame display window : You can insert multi media in this window.
1. Check the <BizChecker> program is running at
Windows tray.
If it is not exist, run the <BizReader> program on
background or Windows start menu, and
<BizChecker> will run at the same time.
2. Connect the camera to your PC with the USB cable.
3. After a few moment, if new namecard image exist,
next dialog box will be appeared. (Camera autodection function will be worked when <BizReader>
is running.) If you check <Delete Original Image>,
the namecard image in digital camera will be
deleted.
4. If you click <OK> button, new namecard images are recognized automatically.
ſ Some movie clips that were compressed with a codec that is not compatible with
the Digimax Master can’t play back in the Digimax Master.
ſ Refer to the [Help] menu in Digimax Master for further information.
ŝ81Ş
Digimax Biz Reader
ƈ Recognizing the namecard image file
ƃ Downloading camera's namecard images to computer
1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display, select [My computer] and double click
[Removable Disk ƍ DCIM ƍ 100SSCAM]. The image files will then be
displayed.
* File names assigned in the Biz mode, will be set SB1ZXXXX
3. Downloading camera's namecard images : Refer to page 76 (Downloading
stored images).
2. Click the [Open] button.
3. Select the namecard image files and click the
[Open] button.
(To select several image files, use <Shift> key
or <Ctrl> key with your mouse.)
4. Namecard images are recognized
automatically.
ƃ Recognizing namecard image file
1. Run the Digimax Biz Reader by double click on
the icon.
ŝ82Ş
Digimax Biz Reader
ƃ Partial recognizing : Partial recognition function can be used when misrecognition.
1. Select the namecard to partial editing.
2. Drag the area to partial editing in namecard image window, choose the
proper field in pop-up window, and then the recognized result is entered to
the field automatically.
‫ۀ‬
‫ڹ‬
‫ں‬
‫ڿ‬
‫ھ‬
ſ Drag only the character area without margin.
ſ Refer to the [Help] menu in Digimax Biz Reader for further information.
‫ڻ‬
‫ڽ‬
‫ڼ‬
CAUTION
ƃ When you picturing the namecard in Biz mode, avoid the palce where too
bright or too dark.
ƃ Take a namecard image with full size shot in guide line without any margin.
ƃ Adjust the focus by half-pressing camera shutter before taking a picture.
ƃ If you use the tripod, it is easier to take clear shot.
- Digimax Biz Reader functions are listed below.
‫ ڹ‬Menu and Buttons : You can select menus.
(Open, Save, Print, E-mail, Home)
‫ ں‬View mode : List View, Thumbnail+List View, Thumbnail View.
‫ ڻ‬Group window : You can manage the group.
‫ ڼ‬Image window : Name card Images in the selected folder are displayed.
‫ ڽ‬List Window : You can preview an image and a contents.
‫ ھ‬Index : You can Search index.
‫ ڿ‬Search : You can Search by keyword input quickly.
‫ ۀ‬Array Button : You can array the following menus in List View,
Thumbnail+List View mode.
(Name, Title, Company, Mobile, Phone, Address, Homepage)
ſ Refer to the [Help] menu in Digimax Biz Reader for further information.
ŝ83Ş
FAQ
ƈ Please check the following if the USB connection malfunctions.
Case 1
USB cable is not connected or it is not the supplied USB cable.
ƍ Connect the supplied USB cable.
Case 2
The camera is not recognised by your PC.
Sometimes, the camera may appear under [Unknown Devices] in
Device Manager.
ƍ Install the camera driver correctly.
Turn off the camera, remove the USB cable, plug in the USB cable
again, and then turn on the camera.
Case 3
There is an unexpected error during file transfer.
ƍ Turn the camera power off and on again. Transfer the file again.
Case 4
When using a USB hub.
ƍ There may be a problem in connecting the camera to the PC through
a USB hub if the PC and the hub are not compatible.
Wherever possible, connect the camera directly to the PC.
Case 5
Are other USB cables connected to the PC?
ƍ The camera may malfunction when it is connected to the PC at the
same time as another USB cable. In this case, disconnect the other
USB cable, and only connect the camera USB cable to the PC.
ŝ84Ş
Case 6
When I open the Device Manager (by clicking Start ƍ (Settings) ƍ
Control Panel ƍ (Performance and Maintenance) ƍ System ƍ
(Hardware) ƍ Device Manager), there are Unknown Devices or Other
Devices entries with a yellow question mark (?) beside them or
devices with an exclamation mark (!) beside them.
ƍ Right-click on the entry with the question (?) or exclamation (!) mark
and select "Remove". Restart the PC and connect the camera again.
For Windows 98SE PC, remove the camera driver, restart the PC, and
then reinstall the camera driver.
Case 7
In some security programs (Norton Anti Virus, V3, etc.), the computer
may not recognise the camera as a removable disk.
ƍ Stop the security programs and connect the camera to the computer.
Refer to the security program instructions about how to temporarily
disable the program.
Case 8
The camera is connected to the USB port located on the front of the
computer.
ƍ When the camera is connected to the USB port located on the front of
the computer, the computer may not recognise the camera. Connect
the camera to the USB port located on the back of the computer.
ƈ When the movie clip doesn’t play back on the PC
ſ When the movie clip recorded by the camera doesn’t play back on the PC,
the causes are most likely due to the codec installed on the PC.
FAQ
ƃ When a codec for playing back the movie clip isn't installed, or isn't compatible
ƍ Install the codec as listed below.
[ Installing codec for Windows ]
1) Insert the CD provided with the camera.
2) Run the Windows Explorer and select [CD-ROM drive:\XviD] folder and click
the XviD-1.1.0-30122005.exe file.
ſ The XviD codec is distributed according to the GNU General Public License
and anyone can copy, distribute and change this codec. This License applies
to any program or other work which contains a notice placed by the copyright
holder saying it may be distributed under the terms of this General Public
License.
For more information, see the License documents
(http://www.gnu.org/copyleft/gpl.html).
ƃ When the DirectX 9.0 or later is not installed
ƍ Install the DirectX 9.0 or later
1) Insert the CD provided with the camera
2) Run the windows explorer and select the [CD-ROM drive:\ USB Driver\
DirectX 9.0] folder and click the DXSETUP.exe file.
The DirectX will be installed. Visit the following site for downloading the
DirectX. http://www.microsoft.com/directx
ƃ If a PC (Windows 98SE) repeatedly stops responding while the camera and PC
are connected
ƍ If a PC (Windows 98SE) is turned on for a long time and the camera has to
be repeatedly re-connected, the PC may not recognise the camera. In this
case, restart the PC.
ƃ If a PC connected with the camera stops responding while Windows is starting.
ƍ In this case, disconnect the PC and the camera and Windows will start.
If the problem happens repeatedly, set the Legacy USB Support to disable
and re-start the PC. The Legacy USB Support is in the BIOS setup menu.
(The BIOS setup menu differs from the PC manufacturers and some BIOS
menus don’t have Legacy USB Support) If you can’t change the menu by
yourself, contact to the PC manufacturer or BIOS manufacturer.
ƃ If the movie clip can't be deleted, or if a removable disk can’t be extracted or if an
error message displays during the file transfer.
ƍ If you install only the Digimax Master, the problems mentioned above
occasionally happen.
- Close the Digimax Master program by clicking the Digimax Master icon on
the Taskbar.
- Install all the application programs included in the software CD.
ŝ85Ş
Correct Disposal of This Product
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for
environmentally safe recycling. Business users should contact their supplier and
check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
FCC notice
ƈ NOTE :
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorientate, or relocate, the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
ƈ CAUTION :
Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the
equipment.
Samsung Techwin cares for the environment at all product
manufacturing stages to preserve the environment, and is
taking a number of steps to provide customers with more
environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly
products, and indicates that the product satisfies the EU
RoHS Directive.
ŝ86Ş
ƈ Declaration of Conformity
Trade Name
: SAMSUNG TECHWIN
Model No.
: Samsung NV11
Responsible Party : Samsung Opto-Electronics America, INC.
Address
: 40 Seaview Dr. Secaucus,NJ 07094
Telephone No.
: 201-902-0347
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
MEMO
MEMO
ŝ87Ş
MEMO
ŝ88Ş
MEMO
SAMSUNG TECHWIN CO., LTD.
SAMSUNG FRANCE S.A.S.
SAMSUNG OPTO-ELECTRONICS UK LIMITED
OPTICS & DIGITAL IMAGING DIVISION
145-3, SANGDAEWON 1-DONG, JUNGWONGU,
SUNGNAM-CITY, KYUNGKI-DO, KOREA
462-121
TEL : (82) 31-740-8086, 8088, 8090, 8092, 8099
FAX : (82) 31-740-8398
www.samsungcamera.com
BP 51 TOUR MAINE MONTPARNASSE 33,
AV .DU MAINE 75755, PARIS CEDEX 15, FRANCE
HOTLINE PHOTO NUMÉRIQUE :
00 800 22 26 37 27(Numéro Vert-Appel Gratuit)
TEL : (33) 1-4279-2200
FAX : (33) 1-4320-4510
www.samsungphoto.fr
SAMSUNG HOUSE 1000 HILLSWOOD DRIVE
HILLSWOOD BUSINESS PARK
CHERTSEY KT16 OPS U.K.
TEL : 00800 12263727
(free for calls from UK only)
UK Service Hotline : 01932455320
www.samsungcamera.co.uk
SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
SAMSUNG OPTO-ELECTRONICS GMBH
HEADQUARTERS
40 SEAVIEW DRIVE, SECAUCUS,
NJ07094, U.S.A.
TEL : (1) 201-902-0347
FAX : (1) 201-902-9342
WESTERN REGIONAL OFFICE
18600 BROADWICK ST.,
RANCHO DOMINGUEZ, CA 90220, U.S.A.
TEL : (1) 310-900-5284/5285
FAX : (1) 310-537-1566
www.samsungcamerausa.com
AM KRONBERGER HANG 6
D-65824 SCHWALBACH/TS., GERMANY
TEL : 49 (0) 6196 66 53 03
FAX : 49 (0) 6196 66 53 66
www.samsungcamera.de
RUSSIA INFORMATION CENTER
SAMSUNG ELECTRONICS
117545 ST. DOROZHNAYA BUILDING 3,
KORPUS 6, ENTRANCE 2, MOSCOW, RUSSIA
TEL : (7) 495-363-1700
CALL FREE : (8) 800 200 0 400 (from Russia only)
www.samsungcamera.ru
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD
No.9 zhangheng Street. Micro-Electronic
Industrial Park Jingang Road Tianjin China.
POST CODE : 300385
TEL : (86) 22-2761-4599
FAX : (86) 22-2769-7558
www.samsungcamera.com.cn
Internet address - http : //www.samsungcamera.com
The CE Mark is a Directive conformity
mark of the European Community (EC)
6806-3755
Download PDF