Samsung | SAMSUNG S85 | Samsung KENOX S85 User Manual

Instructions
Getting to Know your camera
Use this camera in the following order.
Set up the camera driver
Before connecting the camera to a PC,
via the USB cable, you will need to set
up the camera driver. Install the camera
driver that is contained in Application
software CD-ROM. (p.94)
Take a picture
Take a picture. (p.16)
Insert the USB cable
Insert the supplied USB cable into the
PC’s USB port and the camera’s USB
connection terminal. (p.97)
Check the camera's power
Check the camera’s power. If the power
is turned off, preset the
camera button to turn it on.
Check [Removable Disk]
Open Windows’s EXPLORER and search
for [Removable Disk]. (p.97)
Thank you for buying a Samsung Digital Camera.
Prior to using this camera, please read the user manual thoroughly.
If you require After Sales service, please bring the camera and the cause
of the camera malfunction (such as battery, Memory card etc.) to the
A/S centre.
Please check that the camera is operating properly prior to when you
intend to use it (e.g. for a trip or an important event) to avoid disappointment. Samsung takes no responsibility for any loss or damage that may
result from camera malfunction.
Keep this manual in a safe place.
If you use a card reader to copy the images on the memory card to your
PC, the images could be damaged. When transferring the images taken
with the camera to your PC, be sure to use the supplied USB cable
to connect the camera to your PC. Please note that the manufacturer
holds no responsibility for loss or damage of images on the memory
card due to the use of a card reader.
The contents and illustrations of this manual are subject to change
without prior notice for upgrading the camera functions.
ÄMicrosoft, Windows and Windows logo are registered trademarks of
Microsoft Corporation incorporated in the United States and/or other
countries.
ÄAll brand and product names appearing in this manual are registered
trademarks of their respective companies.
1
2
Danger
Warning
DANGER indicates an imminently hazardous situation which, if not
avoided, will result in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not
avoided, could result in death or serious injury.
Do not attempt to modify this camera in any way. To do so may result
in fire, injury, electric shock or severe damage to you or your camera.
internal inspection, maintenance and repairs should only be carried
out by your dealer or Samsung Camera Service centre.
Please do not use this product in close proximity to flammable or
explosive gases, as this could increase the risk of explosion.
Should any form of liquid or a foreign object enter the camera, do not
use it. Switch off the camera, and then disconnect the power source.
You must contact your dealer or Samsung Camera Service centre.
Do not continue to use the camera as this may cause a fire or electric
shock.
Do not insert or drop metallic or inflammable foreign objects into the
camera through access points e.g. the memory card slot and battery
chamber. This may cause a fire or electric shock.
Do not operate this camera with wet hands. This could pose a risk of
electric shock.
Do not use the flash in close proximity to people or animals. Positioning
the flash too close to your subject’s eyes may cause eyesight damage.
For safety reasons keep this product and accessories out of reach of
children or animals to prevent accidents e.g.:
- Swallowing battery or small camera accessories. If an accident should
occur, please consult a doctor immediately.
- There is the possibility of injury from the camera’s moving parts.
Battery and camera may become hot during prolonged use and it may
result in camera malfunction. Should this be the case, allow the camera
to sit idle for a few minutes to allow it time to cool.
Do not leave this camera in places subject to extremely high temperatures, such as a sealed vehicle, direct sunlight or other places
of extremes in temperature. Exposure to extreme temperatures may
adversely affect the camera’s internal components and could cause a
fire.
When in use, do not cover the camera or Charger. This may cause heat
to build up and distort the camera body or cause a fire. Always use the
camera and its accessories in a well-ventilated area.
Caution
CAUTION indicates a potentially hazardous situation which, if not avoided,
may result in a minor or moderate injury.
Leaking, overheating, or damaged battery could result in fire or injury.
- Use battery with the correct specification for the camera.
- Do not short circuit, heat or dispose of battery in fire.
- Do not insert the battery with the polarities reversed.
Remove the battery when not planning to use the camera for a long
period of time. Otherwise the battery may leak corrosive electrolyte and
permanently damage the camera’s components.
Do not fire the flash while it is in contact with hands or objects. Do not
touch the flash after using it continuously. It may cause burns.
Do not move the camera while it is switched on, if you are using the AC
Charger. After use, always switch off the camera before unplugging the
cable from the wall socket. Then make sure that any connector cords
or cables to other devices are disconnected before moving the camera.
Failure to do so may damage the cords or cables and cause a fire or
electric shock.
Take care not to touch the lens or lens cover to avoid taking an unclear
image and possibly causing camera malfunction.
Avoid obstructing the lens or the flash when you capture an image.
Credit cards may be demagnetized if left near case. Avoid leaving
magnetic strip cards near the case.
Using an AC adapter that doesn’t match with the camera specification
may cause camera malfunction. We recommend supplied battery or
exclusive rechargeable battery.
Ä Available AC adapter :
Voltage: 3.3V, Amprer: 2.0A, Diameter ( ): 2.35
After turning on the camera, Check whether the battery type and the
camera setting set on the [Setup] > [Battery Type] menu (p. 56) are
same or not.
Contents
READY 007 System chart
07
008
008
009
010
010
010
011
011
012
013
Identification of features
Front & Top
Back
Bottom / 5 Function button
Self-timer lamp
Camera Status Lamp
Mode icon
Connecting to a Power Source
Inserting the memory card
Instructions on how to use the memory card
RECORDING 015 LCD monitor indicator
15
016
016
016
017
017
018
019
019
019
020
020
Starting the recording mode
How to use the Auto mode
How to use the Program mode
How to use the ASR mode
How to use the Manual mode
How to use the Scene modes
How to use the Portrait mode
How to use the Night mode
How to use the Movie clip mode
Recording the movie clip without sound
Pausing while recording a movie clip
(Successive Recording)
3
Contents
021
022
022
022
022
024
024
026
026
028
030
030
031
032
033
034
034
035
037
038
038
039
039
040
4
Things to Watch Out for When Taking Pictures
Using the camera buttons to set the camera
POWER button
SHUTTER button
ZOOM W / T button
Info / Up button
Macro / Down button
Focus lock
Flash / Left button
Self-timer / Right button
MENU / OK button
E (Effect) button
E (Effect) button : Colour
E (Effect) button : Colour Mask
E (Effect) button : Saturation
E (Effect) button : FUN
Pre-set focus frame
Composite shooting
Photo Frame
Fn button
How to use the Fn menu
Size
Quality / Frame rate
Metering
040
042
042
043
Drive mode
ISO
White balance
Exposure compensation
SETUP 044 Using the LCD monitor to adjust the
44
044
044
045
045
047
047
048
048
049
049
049
049
049
050
050
050
051
camera settings
Recording
Sharpness
Contrast
Auto Focus type
Voice Memo
Voice Recording
Recording the movie clip without voice
SCENE mode
Sound menu
Sound
Volume
Start up sound
Shutter sound
Beep Sound
AF sound
Setup menu
Setup menu 1
Contents
051
052
052
052
053
053
053
053
054
054
054
054
055
056
056
056
File name
LANGUAGE
Setting up the Date / Time / Date type
World Time
Imprinting the recording date
LCD brightness
Auto Focus lamp
Start up image
Setup menu 2
Quick view
Auto power off
LCD save
Selecting Video out type
Formatting a memory
Initialisation
Selecting a battery type
PLAY 057 Starting play mode
57
057
057
058
058
059
059
Playing back a still image
Playing back a movie clip
Movie clip capture function
On camera movie trimming
Playing back a recorded voice
Playing back a voice memo
060
060
060
062
062
063
063
063
064
065
065
066
066
067
068
068
068
068
068
068
069
069
070
LCD monitor Indicator
Using the camera buttons to set the
camera
Thumbnail / Enlargement button
Info / Up button
Play & Pause / Down button
Left / Right / Menu / OK button
Printer button
Delete button
E (Effect) button : Resize
E (Effect) button : Rotating an image
E (Effect) button : Colour
E (Effect) button : Special Colour
Colour Filter
Colour mask
E (Effect) button : Image editing
Red eye Removal
Brightness control
Contrast control
Saturation control
Noise Effect
Effect (E button) : FUN
Cartoon
Preset focus frames
5
Contents
071
073
074
074
076
076
076
077
077
077
078
078
078
079
079
081
082
083
084
084
085
086
087
089
6
Composite image
Photo Frame
Sticker
Setting up the play back function using the
LCD monitor
Starting the slide show
Start the slide show
Selecting Images
Configure slide show effects
Setting play interval
Setting Background Music
Playback
Voice memo
Deleting images
Protecting images
DPOF
Copy To Card
PictBridge
PictBridge : Picture Selection
PictBridge : Print Setting
PictBridge : Reset
Important notes
Warning indicator
Before contacting a service centre
Specifications
SOFTWARE 092 Software Notes
92
092
093
094
096
099
100
100
100
101
104
System Requirements
About the software
Setting up the application software
Starting PC mode
Removing the removable disk
Setting up the USB Driver for MAC
Using the USB Driver for MAC
Removing the USB Driver for Windows 98SE
Samsung Master
FAQ
System chart
Please check that you have the correct contents before using this product. The contents can vary depending on the sales region. To buy
the optional equipment, contact your nearest Samsung dealer or Samsung service centre.
< Included items >
DPOF compatible
printer (see p.79)
User manual,
Product warranty
Camera strap
Software CD
(see p.93)
PictBridge compatible
printer (see p.82)
Computer
(see p.97)
SD/SDHC memory card / MMC
(see p.12)
USB cable
AV cable
Rechargeable battery (SNB-2512)
AA Alkaline Batteries
AC cord
Charger (SBC-N2)
External monitor
(see p. 55)
READY_ 7
01 READY
Camera case
Identification of features
Front & Top
Mode dial
Power button
Shutter button
Speaker
Flash
Self-timer lamp /
AF sensor
USB / AV connection
terminal
Lens/ Lens cover
DC input connection port
Microphone
8 _READY
Identification of features
Back
Camera status lamp
Zoom W button (Thumbnail)
E (Effects) button
Strap eyelet
LCD monitor
Fn / Delete button
5 function button
Play mode /
Printer button
READY_ 9
01 READY
Zoom T button (Digital zoom)
Identification of features
Bottom / 5-function button
Tripod socket
Battery chamber cover
Self-timer lamp
Memory card slot
Battery chamber
Icon
Status
Description
- For the first 7 seconds, the lamp blinks at 1 second
intervals.
- For the final 3 seconds, the lamp blinks quickly at
0.25-second intervals.
✢
Blinking
✡
Blinking
For the 2 seconds, the lamp blinks quickly at 0.25-second intervals.
✣
Blinking
A picture will be taken after about 10 seconds and 2
seconds later a second picture will be taken.
Blinking
After pressing the Shutter button, the image is taken in
accordance with the subject’s movement.
Camera Status Lamp
Status
Information / Up button
Power on
MENU / OK button
Flash /
Left button
Self-timer /
Right button
After taking a picture
When the USB cable is
inserted to a PC
Transmitting Data with a
PC
When the USB cable is
inserted to a printer
Description
The lamp turns on and off when the camera is
ready to take a picture
The lamp blinks while saving the image data and
turns off when the camera is ready to take a picture
The lamp lights up
(LCD monitor turns off after initializing the device)
The lamp blinks (LCD monitor turns off)
The lamp is off
When the printer is printing The lamp blinks
Macro / Down button
Play & Pause button
10 _READY
When the AF activates
The lamp turns on
(The camera focus on the subject)
The lamp blinks
(The camera doesn’t focus on the subject)
Identification of features
Connecting to a Power Source
Mode icon
We recommend batteries for a digital camera (Within a year from the date
of manufacture). The batteries are listed below.
- Non rechargeable batteries
: 2 X AA Alkaline (High Capacity)
- Rechargeable batteries (Optional) : SNB-2512 (Ni-MH)
Refer to page 16 for more information about the camera mode setting.
AUTO
PROGRAM
ASR
MANUAL
ICON
Š
‰
‚
✆
MODE
SCENE
PORTRAIT
NIGHT
MOVIE
ICON
³
†
SCENE
01 READY
MODE
SNB-2512 rechargeable battery Specification
Model
SNB-2512
Type
Ni-MH
Capacity
2500mAh
Voltage
1.2V x 2
Charging time
Approximately 300 Minutes (Use for SBC-N2)
Ä Included battery may vary depending on sales region.
MODE
Children
Landscape
Close-up
Text
ICON
MODE
Sunset
Dawn
Backlight
Fireworks
ICON
MODE
Beach & Snow
Self-shot
Food
Cafe
ICON
„
…
ˆ
Important information about battery usage.
When the camera is not used, turn off the camera power.
Please remove the battery if the camera will not be used for long
periods. Batteries can lose power over time and are prone to leaking if
kept inside the camera.
Low temperatures (below 0°C) can affect the performance of the battery and you may experience reduced battery life.
Batteries will usually recover at normal temperatures.
During extended use of the camera, the camera body may become
warm. This is perfectly normal.
READY_ 11
Connecting to a Power Source
Inserting the memory card
Insert the battery as shown
- If the camera does not turn on after
you have inserted battery, please
check whether the battery (+ / -).
- When the battery chamber cover is
opened, do not press the
battery chamber cover by force. This
may cause damage to the battery
chamber cover.
Insert the memory card as shown.
There are 4 indicators for battery condition that are displayed on the LCD
monitor.
Battery
indicator
Battery
status
12 _READY
i
The battery is
fully charged
h
g
f
Low battery ca- Low battery capacity (Prepare pacity (Prepare Battery empty.
to recharge or
to recharge or (Recharge or use
use spare bat- use spare batspare battery)
tery)
tery)
- Turn off the camera’s power
before inserting the memory card.
- Have the front of the memory
card facing toward the front of the
camera (Lens) and the card pins
toward the back of the camera
(LCD monitor).
- Do not insert the memory card the
wrong way round.
Doing so may damage the
memory card slot.
Instructions on how to use the memory card
If the memory card is subjected to any of the following, the recorded data
may become corrupted :
- When the memory card is used incorrectly.
- If the power is switched off or the memory card is removed while
recording, deleting (formatting) or reading.
Samsung cannot be held responsible for lost data.
It is advisable to copy important data onto other media as back-up e.g.
floppy disks, hard disks, CD etc.
If there is insufficient memory available :
A [Memory Full!] message will appear and the camera will not operate.
To optimise the amount of memory in the camera, replace the memory
card or delete unnecessary images stored on the memory card.
Don't remove the memory card when the camera status lamp is blinking as this may cause damage to data in the memory card.
READY_ 13
01 READY
Be sure to format the memory card (see p.56) if you are using a newly
purchased memory card for the first time, if it contains data that the camera cannot recognise, or if it contains images captured with a different
camera.
Turn off the camera power whenever the memory card is being inserted
or removed.
Repeated use of the memory card will eventually reduce the memory
card’s performance. Should this be the case, you will need to purchase a
new memory card. Wear and tear on the memory card is not covered by
the Samsung warranty.
The memory card is an electronic precision device.
Do not bend, drop or subject the memory card to any heavy impact.
Do not store the memory card in an environment with strong electronic or
magnetic fields, e.g. near loud speakers or TV receivers.
Please do not use or store in an environment where there are extremes in
temperature.
Do not allow the memory card to become dirty or to come into contact
with any liquid. Should this happen, clean the memory card with a soft
cloth.
Please keep the memory card in its case when not in use.
During and after periods of extended use, you may notice that the
memory card is warm. This is perfectly normal.
Do not use a memory card that is used in another digital camera. To
use the memory card in this camera, format the memory card using this
camera.
Do not use a memory card formatted by another digital camera or
memory card reader.
Instructions on how to use the memory card
The camera can use SD/ SDHC Memory Cards and MMC (Multi Media
Cards).
Card pins
When using a 256MB MMC memory, the specified shooting capacity will
be as follows. These figures are approximate as image capacities can be
affected by variables such as subject matter and memory card type.
Recorded image
Super Fine
size
Write protect switch
Still
image
Label
[SD (Secure Digital) memory card]
The SD/ SDHC memory card has a write protect switch that prevents
image files from being deleted or formatted. By sliding the switch to the
bottom of the SD memory card, the data will be protected. By sliding
the switch to the top of the SD memory card, the data protection will be
cancelled.
Slide the switch to the top of the SD memory card before taking a picture.
14 _READY
*Movie
clip
Fine
Normal
30FPS
15FPS
Ÿ
57
103
180
-
-
¬
68
115
206
-
-
­
84
134
233
-
-
✩
93
158
271
-
-
✨
172
265
425
-
-
✧
558
663
742
-
-
ì
-
-
-
About 3'36"
About 7'2"
❪
-
-
-
About 13'18" About 25'38"
The recording times can be changed by the zoom operation.
The zoom button doesn’t function during the movie recording.
LCD monitor indicator
The LCD monitor displays information about the shooting
functions and selections.
No.
1
2
3
4
Description
Icons
Page
p.11
Recording mode
Memory card icon /
Internal memory icon
Number of available
shots remaining
Ö/×
Remaining time
00:00:00
Voice Memo
Ï
6
Description
5
Optical / Digital Zoom bar /
Digital Zoom rate
Icons
Page
p.22
6
Battery
p.12
7
Image Size
p.39
8
Image Quality / Frame Rate
p.39
9
Metering
p.40
10
Drive mode
p.40
11
ISO
p.42
12
White Balance
p.42
13
Exposure compensation
p.43
14
Date / Time
15
Camera shake Warning
2007/08/01 01:00 PM
p.21
16
Auto Focus Frame
p.45
17
Sharpness / Without Sound
18
Contrast
p.45
19
Macro
p.24
/Ç
p.52
p.44/48
20
Self-timer
p.28
-
21
Flash
p.26
p.14
22
Face Recognition
p.46
p.14
23
Aperture Value / Shutter Speed
p.47
24
Color / Saturation
F2.8, 1/30
p.17
p.31/33
RECORDING_ 15
02 RECORDING
[Image & Full Status]
No.
Starting the recording mode
How to use the Auto mode ( μ )
How to use the Program mode ( ¶ )
Select this mode for quick and easy picture taking with minimal user interaction.
Selecting the automatic mode will configure the camera with optimal
settings. You can still manually configure all
functions except the aperture value and shutter speed.
1. Insert the batteries (p.12). Insert the batteries taking note of the polarity (+ / -).
2. Insert the memory card (p.12). As this
camera has a 19MB internal memory, you
do not need to insert the memory card. If
the memory card is not inserted, an image will be stored in the internal memory.
If the memory card is inserted, an image
will be stored on the memory card.
3. Close the battery chamber cover.
4. Press the power button to turn on the
camera. (If the date/time that is displayed
on the LCD monitor is incorrect, reset the date/time before taking a
picture.)
5. Select the AUTO mode by rotating the mode dial.
6. Point the camera towards the subject and compose the image by using the LCD monitor.
7. Press the shutter button to capture an image.
If the auto focus frame turns to red when you press the shutter button
down half way, it means that the camera cannot focus on the subject.
Should this be the case, the camera is unable to capture an image clearly.
16 _RECORDING
1. Select the PROGRAM mode by rotating
the mode dial.
2. Press the Fn button to configure advanced
functions such as Image Size (p.39),
Quality (p.39), Metering (p.40), Drive mode
(p.40), ISO (p.42), White Balance (p.42)
and Exposure Value(p.43).
Starting the recording mode
How to use the ASR mode ( · )
How to use the Manual mode ( ¸ )
Advanced Shake Reduction (ASR) mode.
This mode will reduce the effect of camera shake and help you get a wellexposed image in dim conditions.
You can manually configure all functions aperture value and shutter speed.
1. The digital zoom will not operate in the ASR
mode.
2. If the lighting condition is brighter than
fluorescent lighting conditions, the ASR will
not activate.
3. If the lighting condition is darker than in
fluorescent lighting conditions, camera
shake warning indicator ( Ã ) will display.
For best results only take pictures in situations where the camera shake warning
indicator ( Ã ) is not displayed.
4. If the subject is moving, the captured image may be blurred.
5. Avoid moving the camera while the [Capturing!] message is displayed
to achieve a better result.
6. As the ASR uses the camera's digital signal processor, it may take a
little longer for the camera to process and save the
images.
1. Select the MANUAL mode by rotating the
mode dial.
2. Press the Fn button and menu for the shutter speed and aperture value will display.
Up / Down button : changes aperture value
Left / Right button : changes shutter speed.
3. Press the Fn button twice and take an image.
02 RECORDING
Things to watch out for using the ASR mode
RECORDING_ 17
Starting the recording mode
How to use the Scene modes ( )
The scene modes are listed below.
Use the menu to easily configure optimal settings for a variety of shooting situations.
[Children]
( ) : To take a picture of fast moving objects,
1. Select the Scene mode by rotating the
Mode dial. (p.48)
2. Point the camera towards the subject and
compose the image by using the LCD monitor.
3. Press the shutter button to capture an image.
[Landscape]
( ) : To take pictures of distant scenery.
[Close Up]
( ) : Close-up shooting for small objects such as
[Text]
( ) : Use this mode to shoot a document.
for example, children.
plants and insects.
[Sunset]
( ) : For taking pictures of sunsets.
[Dawn]
( ) : Daybreak scenes.
[Backlight]
( ) : Portrait without shadows caused by backlight.
[Firework]
( ) : Firework scenes.
[Beach & Snow]
( ) : For ocean, lake, beach and snowscape
[Self Shot]
( „ ) : Use when the photographer would also like to
[Food]
( … ) : For taking delicious looking food.
[Cafe]
( ˆ ) : For taking pictures in cafes and restaurants.
scenes.
appear in the image.
18 _RECORDING
Starting the recording mode
How to use the Portrait mode ( )
How to use the Movie clip mode ( ´ )
Please select this mode for quick and easy picture
with people's face.
Select Face mode using mode dial.
A movie clip can be recorded for as long as the available recording time
of the memory capacity allows.
This mode helps to get a well-exposed pictures
in the night time and darkness.
Select Night mode using mode dial.
02 RECORDING
How to use the Night mode ( )
1. Select the Movie clip mode by rotating the
Mode dial. ( The Movie clip mode icon and
available recording time will display on the
LCD monitor.).
2. Point the camera towards the subject and
compose the image by using the LCD
monitor.
3. Press the shutter button once and movie
clips are recorded for as long as the available recording time allows. Movie clips
will still be recorded if the shutter button
is released. If you wish to stop recording,
press the shutter button again.
Ä Image size and type are listed below.
- Image size
: 640x480, 320x240 (Selectable)
- Movie clip file type : AVI (MJPEG)
- Frame Rate
: 30FPS, 15FPS (Selectable)
RECORDING_ 19
Starting the recording mode
Recording the movie clip without sound
You can record the movie clip without sound.
Steps from 1-3 are the same as those for
MOVIE CLIP mode.
4. Press the Menu button.
5. Select the [RECORDING] menu by pressing
the Left / Right button.
6. Press the Down button to select the [Voice
Mute] menu and press the Right button.
7. Select the [On] menu by pressing the Up /
Down button.
8. Press the OK button. You can record a
movie without sound.
20 _RECORDING
Pausing while recording a movie clip
(Successive Recording)
This camera allows you to temporarily stop during unwanted scenes,
while recording a movie clip. Using this function, you can record your
favourite scenes into a movie clip without having to create multiple movie
clips.
Using Successive Recording
Steps from 1-2 are the same as those for
MOVIE CLIP mode.
3. Press the shutter button and movie clips are
recorded for as long as the available recordRecord
SH Stop
ing time. Movie clips will still be recorded if
the shutter button is released.
4. Press the Pause button ( Ø ) to pause recording.
5. Press the Pause button ( Ø ) again to resume the recording.
6. If you wish to stop recording, press the shutter button again.
Things to Watch Out for When Taking Pictures
Pressing the shutter button down half way.
Lightly press the shutter button to confirm focus and flash battery
charge. Press the shutter button all way down to take the picture.
[Press the shutter button]
The available memory capacity may vary depending on shooting conditions and camera settings.
When the Flash Off or Slow synchro mode is selected in a low lighting
condition, the camera shake warning indicator ( Ã ) may appear on the
LCD monitor. In this case, use a tripod, support the camera on a solid
surface or change to flash shot mode.
Shooting against the light : Please do not take pictures against the sun.
Doing so may make the picture dark. To
take a picture against the light, please use
the [BACKLIGHT] in the scene shooting
mode (see page 18), fill-in flash (see page
26), spot metering (see page 40), or exposure compensation (see page 43).
Avoid obstructing the lens or the flash when you capture an
image.
Compose the image by using the LCD monitor.
RECORDING_ 21
02 RECORDING
[Lightly press the shutter button]
Under certain conditions the auto focus system may not perform as
expected.
- When photographing a subject that has little contrast.
- If the subject is highly reflective or shiny.
- If the subject is moving at high speed.
- When there is strong reflected light, or when the background is very
bright.
- When the subject matter has only horizontal lines or the subject is very
narrow (such as a stick or flagpole).
- When the surroundings are dark.
Using the camera buttons to set the camera
The recording mode function can be set up by using the camera buttons.
POWER button
Used for turning the camera’s power on / off.
If there is no operation during the specified
time, the camera's power will be turned off
automatically to save battery life.
Refer to page 54 for more information about
the auto power off function.
ZOOM W / T button
If the menu is not displayed, this button works
as the OPTICAL ZOOM or DIGITAL ZOOM button.
This camera has a 5X optical zoom and a 5X
digital zoom function. Using both will offer a
total zoom ratio of 25X.
TELE Zoom
Optical zoom TELE
Digital zoom TELE
SHUTTER button
Used for taking an image or recording voice in the RECORDING mode.
In MOVIE CLIP mode
Pressing the shutter button down fully starts
the process for recording a movie clip.
Press the shutter button once and the movie
clip is recorded for as long as the available
recording time in the memory allows. If you
wish to stop recording, press the shutter button again.
In STILL IMAGE mode
Pressing the shutter button down halfway activates the autofocus and
checks the condition of the flash. Pressing the shutter button down fully
takes and stores the image. If you select voice memo recording, the
recording will start after the camera has finished storing the image data.
22 _RECORDING
: Pressing the ZOOM T button. This will zoom
into the subject i.e. the subject will appear
nearer.
: When the maximum (5X) optical zoom is selected, pressing the ZOOM T button activates
the digital zoom software. Releasing ZOOM T
button stops the digital zooming at the required
setting. Once the maximum digital zoom (5X)
is achieved, pressing the ZOOM T button will
have no effect.
Pressing
the ZOOM
T button
Pressing
the ZOOM
T button
[WIDE zoom]
[TELE zoom]
[Digital zoom 5.0X]
ZOOM W / T button
WIDE Zoom
Optical zoom WIDE
Images taken using the digital zoom may take a little longer for the
Pressing
the ZOOM
W button
Pressing
the ZOOM
W button
[TELE zoom]
[Optical zoom 2X]
Digital zoom WIDE
Optical zoom
Digital zoom
zoom.
To view a clearer digital zoom image, press the shutter button halfway
at the maximum optical zoom position and press the zoom T button
again.
The digital zoom can't be activated in some Scene modes (Children,
Text, Close-up, Fireworks, Self-Shot, Food), Night mode, Motion
Capture mode, ASR mode, movie clip mode and Face recognition.
Take care not to press the lens as this may cause a camera
malfunction.
[WIDE zoom]
: When the digital zoom is in operation, pressing the ZOOM W button will reduce the digital
zooming in steps. Releasing ZOOM W button
stops digital zooming. Pressing the ZOOM W
button will reduce the digital zoom and then it
will continue to reduce the optical zoom until the
minimum setting is reached.
Pressing
the ZOOM
W button
Pressing
the ZOOM
W button
[Digital zoom 5.0X]
camera to process. Allow time for this to take place.
The digital zoom cannot be used in movie clip shots.
You may notice a decrease in image quality when using the digital
[TELE zoom]
[WIDE zoom]
RECORDING_ 23
02 RECORDING
: Pressing the ZOOM W button. This will zoom
out from the subject i.e. the subject will appear
further away. Pressing the ZOOM W button
continuously will set the camera to its minimum
zoom setting i.e. the subject appears at its
furthest from the camera.
Info ( î ) / Up button
Macro ( e ) / Down button
While the menu is showing, the Up button operates as a direction button.
In the recording modes or playback mode, pressing this button will display
the image information.
While the menu is showing, press the DOWN button to move from the
main menu to a sub menu, or to move down the sub menu. When the
menu is not showing, you can use the MACRO / DOWN button to take
macro pictures.
The distance ranges are shown below. Press the Macro button until the
desired macro mode indicator appears on the LCD monitor.
Info ( î ) button
24 _RECORDING
[Auto Focus]
[Macro ( e )]
[Auto Macro ( d )]
[Super Macro ( )]
Macro ( e ) / Down button
Types of focus mode and focus range (W : Wide, T : Tele)
Focus Type
Auto macro ( d )
Normal
W : 5 ~ Infinity
T : 50 ~ Infinity
W : 80 ~ Infinity
T : 80 ~ Infinity
Program ( ‰ )
Mode
Focus Type
Super macro ( )
macro ( e )
Normal
Focus range
W:1~5
(Wide only)
W : 5 ~ 80
T : 50 ~ 80
W : 80 ~ Infinity
T : 80 ~ Infinity
ASR Mode ( ‚ )
Mode
Focus Type
Focus range
Auto macro ( d )
W : 5 ~ 80
T : 50 ~ 80
Available focusing method, by recording mode
( o : Selectable, : Infinity focus range)
Mode
Auto macro
Š
‰
‚
✆
†
o
Mode
Normal
W : 80 ~ Infinity
T : 80 ~ Infinity
When the macro mode is selected, be particularly careful to avoid
camera shake.
When you take a picture within 40cm (Wide zoom) or 50cm
(Tele zoom) in the Macro mode, select the FLASH OFF mode.
When you take a picture within the 10cm Super macro range, the
auto-focus on the camera will take longer to set the correct focus
distance.
„
…
ˆ
Super macro
Macro
o
o
Normal
o
o
o
o
o
o
o
o
o
o
o
Macro
Normal
SCENE
Auto macro
Super macro
o
o
o
o
o
o
o
o
RECORDING_ 25
02 RECORDING
Focus range
(Unit: cm)
Auto ( Š )
Mode
Focus lock
Flash (
To focus on a subject not positioned in the centre of the picture, use the
focus lock function.
When the menu is displayed on the LCD monitor, pressing the LEFT button makes the cursor
shift to the left tab.
When the menu is not displayed on the LCD
monitor, the LEFT button operates as the
FLASH button.
Using the Focus Lock
1. Ensure the subject is in the centre of the autofocus frame.
2. Press the SHUTTER button halfway. When the green auto focus frame
lights up, it means the camera is focused on the subject. Be careful
not to press the SHUTTER button all the way down to avoid taking an
unwanted picture.
3. With the SHUTTER button still pressed down only halfway, move the
camera to recompose your picture as desired, and then press the
SHUTTER button completely to take the picture. If you release your finger from the SHUTTER button, the focus lock function will be cancelled.
) / Left button
[Selecting the Auto flash]
Selecting the flash mode
1. Press the Mode button to select a RECORDING mode with the
exception of the Movie clip mode or the ASR mode.
2. Press the Flash button until the desired flash mode indicator is
displayed on the LCD monitor.
3. A flash mode indicator will be displayed on the LCD monitor.
Use the correct flash to suit the environment.
Flash range
(Unit: m)
Normal
Macro
Auto macro
ISO
1. The image to be
captured.
26 _RECORDING
2. Press the SHUTTER button
halfway and focus
on the subject.
3. Recompose the
picture and fully depress the SHUTTER
button.
WIDE
AUTO
TELE
WIDE
TELE
WIDE
TELE
0.8 ~ 3.0 0.8 ~ 2.5 0.4 ~ 0.8 0.5 ~ 0.8 0.4 ~ 3.0 0.5 ~ 2.5
Ä When the Super Macro is selected, flash is fixed as the Flash Off mode.
Flash (
) / Left button
If you press the shutter button after selecting the Auto, Fill-in, Slow
Flash mode indicator
Icon
Flash mode
^
Auto flash
]
Auto & Red eye
reduction
Description
If the subject or background is dark, the
camera flash will operate automatically.
If a subject or background is dark, the
camera flash will work automatically and will
reduce the red-eye effect by using the redeye reduction function.
Fill in flash
The flash fires regardless of the available light.
The intensity of the flash will be automatically
controlled to suit the prevailing conditions.
Slow synchro
The flash operates with a slow shutter speed
to obtain a balanced correct exposure. In
poor lighting conditions the camera shake
warning indicator ( Ã ) will display on the
LCD monitor.
Œ
Flash off
The flash does not fire.
Select this mode when capturing images in a
place or situation where flash photography is
prohibited. When you capture an image in a
poorly lit condition, the camera shake warning indicator ( Ã ) will appear on the LCD
monitor.
!
Red-eye reduction
When a shot with "red eye" is detected, this
mode will reduce the red-eye effect automatically.
ª
RECORDING_ 27
02 RECORDING
synchro flash, the first flash fires to check the shooting condition (Flash
range and Power ratio of flash).
Do not move the camera until the second flash fires.
Using the flash frequently will reduce the life of the battery.
Under normal operating conditions the re-charging time for the flash is
usually within 5 seconds. If the battery is weak, the charging time will
be longer.
In the ASR mode, [Landscape], [Close up], [Text], [Sunset], [Dawn],
[Firework], [Self Shot], [Food], [Cafe] scene modes and the Movie clip
mode, the flash function will not operate.
Take photographs within the flash range.
The image quality is not guaranteed if the subject is too close or highly
reflective.
When taking an image in poorly lit conditions with the flash, there may
be a white speck in the captured image. The speck is caused by the
flash light reflecting off atmospheric dust.
Flash (
Self-timer ( ✢ ) / Right button
) / Left button
Available flash mode, by recording mode
Mode
^
]
Š
‰
‚
✆
†
o
o
o
o
Mode
„
…
ˆ
ª
o
o
( o : Selectable)
Œ
!
o
o
o
o
When the menu is displayed on the LCD monitor, pressing the Right button makes the cursor shift to the right tab.
When the menu is not displayed on the LCD monitor, the RIGHT button
operates as the Self-timer ( ✢ ) button. This function is used when the
photographer would also like to be in the image.
o
o
o
o
o
o
o
If you operate the Self-timer button during the self-timer operation, the
o
o
Use a tripod to prevent the camera from shaking.
In Movie Clip mode, only the 10SEC self-timer will work.
o
SCENE
^
]
ª
o
Œ
!
o
o
o
o
o
o
o
o
o
o
28 _RECORDING
o
o
o
self-timer function is cancelled.
Self-timer ( ✢ ) / Right button
Selecting the self-timer
Motion Timer
1. Rotate the Mode dial to select a RECORDING mode with the exception of VOICE
RECORDING mode.
2. Press the SELF-TIMER ( ✢ ) button until the
desired mode indicator displays on the LCD
monitor. A 10 second, 2 second, Double selftimer or Motion timer icon appears on the LCD
monitor.
3. When you press the SHUTTER button, the
picture will be taken after the specified time
has elapsed.
Motion
Icon & Self-timer lamp
Pressing the Shuter button after
Blink (0.5 second interval)
setting the Motion Timer
Blink (0.25 second interval)
No movement is detected
Turn on and the image is taken after
2 seconds
The Motion Timer flows are as followings. (Night mode or Fireworks
mode excluded)
[Selecting the 10 SEC
self-timer]
Self-timer mode indecator
Icon
Mode
Description
✢
10SEC
self-timer
Pressing the shutter button will allow an interval
of 10 seconds before the image is taken.
✡
2SEC
self-timer
Pressing the shutter button will allow an interval
of 2 seconds before the image is taken.
Selecting the Motion Timer " Pressing the Shutter button " Confirming the composition (Within 6 sec.)*1 " Starting the detection (Swing
your hands fully)*2 " Stopping the detection (Do not move) " Taking
an image (after 2 sec.)
*1: The camera detects the subject's movement 6 seconds after pressing the Shtter button, so confirm the composition within 6 seconds.
*2: Move your body or hands fully.
In the following cases, the Motion Timer may not operate.
✣
Double
self-timer
Motion
Timer
A picture will be taken after about 10 seconds
and 2 seconds later a second picture will be
taken. When using the flash, the 2-second selftimer may be delayed for longer than 2 seconds
depending on the flash charging time.
The camera detects the subject's movement 6
seconds after pressing the Shutter button, and the
picture is taken when the movement is stopped.
The focus distance is over 3m.
The exposure is too bright or dark
In backlight conditions.
The movement is insignificant
The movement is detected out of the
The detection range
of Motion Timer
center part (50%) of the sensor where
the movement is recognized.
RECORDING_ 29
02 RECORDING
Detecting the subject's movement
MENU / OK button
E (Effect) button
MENU button
- When you press the MENU button, a menu related to each camera
mode will be displayed on the LCD monitor. Pressing it again will return
the LCD to the initial display.
- A menu option can be displayed when the following are selected :
MOVIE CLIP and STILL IMAGE mode. There is no menu available when
the VOICE RECORDING mode is selected.
It is possible to add special effects to your images by using this button.
Still image mode : You can select the colour, special colour, image editing and Fun menu. In the Auto mode, you can select
the [COLOR] menu only.
Movie clip mode : You can select the colour menu.
Available Effects, by recording mode
( o : Selectable)
† Š ‰ ✆ „ … ˆ
RECORDING
Sharpness
Normal
Contrast
Normal
Auto Focus
Center AF
Voice Memo
[Pressing the MENU button]
Voice Record
[Menu off]
Off
Move
MENU Exit
[Menu on]
OK button
- When the menu is displayed on the LCD monitor, this button is used for
shifting the cursor to the sub menu or for confirming data.
30 _RECORDING
æ
«
Æ
ë
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
This button will not operate in ASR, Voice recording mode and some
scene modes (Night, Text, Sunset, Dawn, Backlight, Fireworks,
Beach&Snow).
Even if the camera is turned off, the effect setting will be
preserved. To cancel the special effect, select ( ä ) sub menu in the
Colour menu and select the ( å ) sub menu in the rest effect menus.
If the image size is ( ¬ ) or , ( ­ ) the FUN menu can't be selected.
E (Effect) button : Colour
By using the camera’s digital processor, it is possible to add special effects
to your images
Press the E button in an available recording mode. (p.30)
COLOR
Move
- Up/Down button : Selects R, G, B
- Left/Right button : Changes the values
Move
E
Exit
[Still image mode]
Move
E
OK Set
Custom Color
Exit
[Movie clip mode]
1. Select a desired sub menu by pressing the Up/Down button and press
the OK button.
Icon
Custom Color
Description
ä
Û
No effect is added to the image.
Ü
Captured images will be stored in a sepia tone
(a gradient of yellowish brown colours).
Þ
ß
Ý
Captured images will be stored in a red tone.
Move
OK Set
Ä In the Auto mode, the Custom Color can't be selected.
Captured images will be stored in black and white.
Captured images will be stored in a green tone.
Captured images will be stored in a blue tone.
Save the image in negative mode.
¼
Captured image will be saved in set RGB tone.
2. Press the shutter button to capture an image.
RECORDING_ 31
02 RECORDING
COLOR
Custom colour : You can change the R (Red),
G (Green) and B (Blue) values
of the image.
E (Effect) button : Colour Mask
With this menu, you can select a part you want to highlight. The rest of the image will be black and white.
Press the E button in an available recording mode. (p.30)
Color Mask
Press the OK button and the Mask
mark will be displayed on the LCD
monitor.
OK Set
E
Press the Fn button. You can
change the size and locaton of the
mask.
SH Capture
Back
Fn Edit
Move
SH Capture
TW Size
Zoom W / T button :
Changing the Mak size
Move
Press the Shutter button the mask
added image is taken.
[Final image]
Press the Fn button.
SH Capture
Up/Down/Left/Right button:
Moving the mask
Fn Edit
[Mask added image]
Move
32 _RECORDING
SH Capture
TW Size
SH Capture
TW Size
E (Effect) button : Saturation
You can change the saturation of the image.
Press the E button in an available recording mode. (p.30)
Saturation
IMAGE ADJUST
Move
E
Exit
Select Saturation menu (
) and a
bar for changing the saturation will
be displayed.
02 RECORDING
Change the saturation by pressing
the Left/Right button.
Move
OK Set
Bar for changing the saturation
Saturation
Move
OK Set
+ direction: High saturation (The colour will be intense)
- direction: Low saturation (The colour will be subtle)
Press the Shutter button to take a
picture.
Press the OK button and the
saturation of image will be
changed.
[Final Image]
RECORDING_ 33
E (Effect) button : FUN
Pre-set focus frame
You can make the subject stand out from its surroundings. The subject
will be sharp and in focus while making the rest out of focus.
Moving and changing the focus frame
You can change the focus frame after selecting a Range menu.
Press the E button in an available recording mode. (p.30)
Pressing the Fn button
FUN
SH Capture
High Light
SH Capture
Fn Edit
Move
E
Range
Exit
Move
[The range is activated :
The colour of focus frame
turns white.]
[Point the camera towards the
subject and compose the image
by using the LCD monitor.]
OK Set
Pressing the Up/Down/
Left/Right button
1. Select a proper menu by pressing the Left/Right button and press the
OK button.
High light
High light
High light
Pressing the Fn button
High light
SH Capture
Range
OK
Set
[Range 1]
Range
OK
Set
[Range 2]
Range
OK
Set
Range
[Range 3]
OK
Set
Fn Edit
Pressing the shutter button
[Range 4]
2. The preset focus frame will appear.
Press the shutter button to capture an image.
SH Capture
Fn Edit
[Final image]
34 _RECORDING
SH Capture
Move
[After changing the range]
E (Effect) button : FUN
Composite shooting
Ä Selecting 2 composite shots
You can combine 2 ~ 4 different shots in a still image.
FUN
Composite
SH Capture
SH Capture
[Ready for taking]
Move
E
Composite
Exit
Pressing the shutter button
OK Set
1. Select a desired menu by pressing Left/Right button and press the OK
button.
Composite
Composite
Composite
Pressing the
OK button
Composite
OK Save
[The final picture]
Composite
OK
Set
[Composite 1]
Composite
OK
Set
[Composite 2]
Composite
Fn Delete
[First shot]
OK
Set
[Composite 3]
Composite
OK
Fn Delete
[Second shot]
Set
[Composite 4]
2. After selecting a desired menu, press the shutter button to take a
picture.
After taking the last image, press the OK button to save the
image.
You can use the flash, self-timer, macro focus and the Zoom W / T
button during the composite shooting.
If you press the Play mode, MENU, E button or turn Mode dial during
the composite shots, each camera working mode is executed. The
previously captured images will be deleted.
RECORDING_ 35
02 RECORDING
Pressing
the shutter
button
Press the E button in an available recording mode. (p.30)
E (Effect) button : FUN
Changing a part of composite shot before taking the last shot
Before taking the last composite shot, you can change a part of composite shot.
1. During the composite shots, press the Fn button.
2. A previous image will be deleted and new frame will be
displayed. To delete a previously taken image, press the Fn button
again.
Changing a part of composite shot after taking the last shot
1. After taking the last shot, a cursor to select a frame will appear.
Press the Up/Down/Left/Right button to select the frame.
2. Press the Fn button and an image will be deleted. Composite frame
will be activated.
3. Press the Shutter button. You can take other images again by using
the Press the Up/Down/Left/Right button and Fn button.
4. Press the OK button again to save the captured image.
Pressing the
up button
Pressing the Fn button
SH Capture
Fn Delete
SH Capture
Fn Delete
OK Save
[Before taking the 3rd shot]
[Moving backward to the
2nd shot]
Fn Delete
OK Save
[After taking 4th shot]
Fn Delete
[Moving backward to the 2nd shot]
3. Press the shutter button to capture a new image.
Pressing the Fn
button
Pressing the
Shutter button
SH Capture
[Deleting 2nd shot]
Pressing the
OK button
OK Save
Fn Delete
[Taking 2nd shot again]
36 _RECORDING
[Final Image]
E (Effect) button : FUN
Photo Frame
02 RECORDING
You can add 9 types of frame-like borders to a still image you want to
capture.
Date & Time information will not be printed on the stored image taken with
Photo Frame menu.
Press the E button in an available recording mode. (p.30)
FUN
Move
Photo Frame
E
Frame
Exit
OK Set
Pressing the
OK button
2. The selected photo frame will be displayed. Press the shutter button to
take a picture.
SH Capture
Move
Pressing the Fn
button
SH Capture
Fn Frame
1. Select a desired sub menu by pressing the Left/Right button and press
the OK button.
RECORDING_ 37
Fn button
You can use the Fn button to set the following menus.
How to use the Fn menu
( o : Selectable)
Š
‰
‚
✆
³
†
Page
Size
o
o
o
o
o
o
o
o
p.39
Quality/
Frame rate
o
o
o
o
o
o
o
o
p.39
o
o
Metering
o
Drive
o
ISO
o
o
o
*1
o
1. Press the Fn button in an available mode.
2. Select a desired menu by pressing the Up / Down button. And then a
sub menu will be displayed at the bottom left of the LCD monitor.
p.40
p.40
o
p.42
SIZE
3264X2448
White
Balance
o
EV
o
o
o
p.42
o
p.43
*1. This menu is only available in the Children scene mode ( ).
QUALITY
Fine
3. Select a desired menu by pressing the Left / Right button and then
press the OK button.
SIZE
3264X2448
38 _RECORDING
Up / Down
button
Left / Right
button
SIZE
3264X2176
Quality / Frame rate
Size
You can select the image size appropriate for your application.
(Unit: pixel)
Movie clip
mode
Icon
Ÿ
¬
­
✩
✨
✧
Size
3264 x
2448
3264 x
2176
3264 x
1824
2592 x
1944
2048 x
1536
1024 x
768
Icon
ì
❪
Size
640 x 480
320 x 240
SIZE
SIZE
3264X2448
640X480
[ STILL IMAGE mode ]
Mode
STILL IMAGE mode
V
Icon
Sub menu Super Fine
File
Format
jpeg
W
X
#
¥
Fine
Normal
30FPS
15FPS
jpeg
jpeg
avi
avi
30FPS
Fine
[ STILL IMAGE mode ]
available because high resolution images require more memory.
FRAME RATE
QUALITY
[ MOVIE CLIP mode ]
The higher the resolution, the lower the number of shots
MOVIE CLIPO mode
[ MOVIE CLIP mode ]
This file format complies with the DCF (Design rule for Camera File
system).
JPEG (Joint Photographic Experts Group) :
JPEG is the image compression standard developed by the Joint Photographic Experts Group. This type of compression is most commonly
used for compressing photos and graphics because it can compress
the files efficiently.
RECORDING_ 39
02 RECORDING
Still
image
mode
You can select the compression ratio appropriate for your application of
the captured images. The higher the compression ratio, the lower the
picture quality.
Metering
Drive mode
If you cannot obtain suitable exposure conditions, you can change the
metering method to take brighter pictures.
You can select continuous shot, and AEB (Auto Exposure
Bracketing).
[Multi]
[Spot]
[Center]
: Exposure will be calculated based
on an average of the available light
in the image area. However, the
calculation will be biased towards
METERING
the centre of the image area. This is
Multi
suitable for general use.
: Only the rectangular area in the
centre of the LCD monitor will be metered for light. This is
suitable when the subject in the centre is exposed correctly,
regardless of the back lighting.
: Exposure will be calculated based on an average of the available light in the image area. However, the calculation will be
biased towards the centre of the image area. This is suitable
for taking a picture of small object like a flower or insects.
Ä If the subject is not the centre of the focus area, do not use the spot
metering as this may result in an exposure error. In this circumstance,
it is better to use exposure compensation.
40 _RECORDING
[Single]
[Continuous]
: Take one picture only.
: Images will be taken continuously until the shutter
button is released.
DRIVE
[Motion Capture] : This takes 7 shots per
Single
second, when the shutter is
pressed and held down. After completing the continuous
shooting, images are saved and the images play back on
the Rear LCD. The maximum number of shots is 30 and
the image size is fixed as VGA.
[AEB]
: Take three pictures in a series in different exposures:
short exposure (-1/3EV), standard exposure (0.0EV),
and over exposure (+1/3EV).
[Wise Shot]
: Two images are taken at a time. One is taken in the Fill-In
Flash mode and the other is taken in the ASR mode.
Drive mode
High resolution and picture quality increases file saving time, which
How to use the wise shot
increases stand-by time.
1. Select the ASR mode by rotating the mode
dial.
2. Select the wise shot in the [DRIVE] menu.
3. Press the Shutter button to take i mages.
4. The captured images are displayed.
- To select an image, press the Left/Right
button.
If the [Continuous]. [Motion Capture] or [AEB] sub menu is selected,
the flash will be off automatically.
If less than 3 pictures are available in the memory, the AEB shooting is
Wise Shot
not available.
It is best to use a tripod for the AEB shooting as the time to save each
image file is longer and blurring caused by camera shake may occur.
In the Wise shot mode, the shutter speed value shown on the LCD
monitor may be different to the actual shutter speed.
If ( ¬ ) or ( ­ ) image size is selected, the Wise Shot menu can't be
Image with
Flash
Enlarged
image
Image with the
ASR mode
OK Save
E
Move
selected.
Enlarged
image
- Press the E button and you can check the enlarged image by pressing
the 5 function button.
- Press the E button again and the image is enlarged automatically.
- You can zoom in and out the enlarged image area by using the W/T
button.
5. Press the OK / Shutter button and the selected image will be saved.
RECORDING_ 41
02 RECORDING
DRIVE
ISO
White balance
You can select the ISO sensitivity when taking pictures.
The speed or specific light-sensitivity of a camera is rated by ISO numbers.
The white balance control allows you to adjust
the colours to appear more natural.
[Auto] : The camera's sensitivity is automatically
changed by variables such as lighting
value or subject brightness.
[ISO 50, 100, 200, 400, 800, 1600 ] :
ISO
You can increase the shutter speed while the
Auto
same amount of light is present, by increasing
the ISO sensitivity. However, the image may be
saturated in high luminance.
The higher the ISO value, the higher the camera’s sensitivity to light and
therefore the greater its capacity to take pictures in dark conditions.
However, the noise level in the image will increase as the ISO value
increases, making the image appear coarse.
WHITE BALANCE
Auto WB
Mode
Icon
Description
Auto WB
x
The camera automatically selects the
appropriate white balance settings,
depending on the prevailing lighting
conditions.
Daylight
z
For taking images outside.
Cloudy
$
Fluorescent_H
%
For taking images under a cloudy and
overcast sky.
For shooting under daylight fluorescent
types of three-way fluorescent lighting.
Fluorescent_L
&
Tungsten
Custom Set
Å
Shooting under white fluorescent lighting.
For shooting under tungsten (standard
light bulb) lighting.
Allows the user to set the white balance
according to the shooting condition.
Ä Different lighting conditions may cause a colour cast on your
images.
42 _RECORDING
White balance
Exposure compensation
Using the Custom White Balance
White balance settings may vary slightly depending on the shooting
environment. You can select the most appropriate white balance setting
for a given shooting environment by setting up the custom white
balance.
This camera automatically adjusts the exposure according to the ambient
lighting conditions.
You can also select the exposure value by using the Fn button.
2. MENU/OK button : selects previous custom white balance.
White paper
Shutter button
: saves new custom
white balance.
- The custom white balance value will be applied, starting with the next
picture you take.
- The user configured white balance will be remain effective until it is
overwritten.
Ä A negative exposure compensation value reduces the exposure. Note
that a positive exposure compensation value increases the exposure
and the LCD monitor will appear white or you may not get good
pictures.
RECORDING_ 43
02 RECORDING
1. Select the CUSTOM ( Å ) menu of the
White Balance and place a sheet of white
paper in front of the camera so that the
LCD monitor shows only white.
Compensating Exposure
1. Press the Fn button, and then use the UP
and DOWN buttons to select the exposure
compensation icon ( Â ).
The exposure compensation menu bar will
EXPOSURE VALUE
appear as shown.
2. Use the LEFT and RIGHT buttons to set the
desired exposure compensation factor.
3. Press the Fn button again. The value you set will be saved and the
Exposure Compensation setup mode will close. If you change the
exposure value, the exposure indicator ( Â ) will be displayed on the
bottom of the LCD monitor.
Recording ( Ò )
You can use the menu on the LCD monitor to set up recording functions.
The items indicated by
are default settings.
Sharpness
Mode
Menu
Sub menu
Soft+
Sharpness
Available mode
Soft
Normal
Vivid
Vivid+
-
High
Normal
Low
-
Face Recognition
Center AF
Multi AF
-
Off
On
Contrast
Auto Focus
Ò
( Recording ) Voice Memo
p.44
p.45
-
Off
p.47
p.47
On
p.48
CHILDREN LANDSCAPE CLOSE UP
TEXT
SUNSET
DAWN
Scene mode
p.48
BACKLIGHT
SELF SHOT
FIREWORK BEACH&SNOW
FOOD
CAFÉ
Ä Menus are subject to change without prior notice.
44 _SETUP
You can adjust the sharpness of the picture you
are about to take. You cannot check the sharpness effect on the LCD monitor before you
take a picture, because this function is applied
only when the captured image is stored on the
memory.
RECORDING
Sharpness
Soft+
Contrast
Soft
Auto Focus
Vivid
Voice Memo
Voice Record
Back
Normal
Vivid+
OK
Set
p.45
Voice
Record
Voice Mute
Page
Using the LCD monitor to adjust the camera settings
[Soft+]/ [Soft] : The edges of the image are softened. This effect is
suitable for editing images on your PC.
[Normal]
: The edges of the image are sharp.
This is suitable for printing.
[Vivid]/ [Vivid+] : The edges of the image are emphasized.
The edges will appear sharp, but noise may occur in the
recorded image.
Recording ( Ò )
Auto Focus type
You can set the difference between bright part of the image and dark part
of the image.
You can select your preferred Focus Area
according to the shooting conditions.
RECORDING
Sharpness
Contrast
High
Auto Focus
Low
Voice Memo
Back
Auto Focus
Voice Memo
Back
Face Recog.
Center AF
Multi AF
OK
Set
Normal
Voice Record
Contrast
Voice Record
: The image contrast is high.
: The contrast is normal.
: The image contrast is more
subtle.
Sharpness
OK
Set
[Face Recognition] : The size and position of the focus frame is set at
the face of the subject automatically.
[Center AF]
: The rectangular area in the center of the LCD
monitor will be focused
[Multi AF]
: This camera selects all of available AF point from
the 9 AF points.
[Face Recognition]
[Center AF]
[Multi AF]
Ä When the camera focuses on the subject, the auto focus frame turns
to green. When the camera doesn't focus on the subject, the auto
focus frame turns to red.
SETUP_ 45
03 SETUP
[High]
[Normal]
[Low]
RECORDING
Contrast
Recording ( Ò )
Face Recognition(FR): This mode detects the face position of the subject automatically and then sets the focus and
exposure. Select this mode for quick and easy
face picture.
Ä Selectable modes: Auto, Program, ASR, Manual, Scene modes (Portrait,
Children, Beach & Snow, Self-shot, Cafe)
1. Press the FR(Face Recognition) button
( ( ) in the selectable modes. The FR icon
will be displayed on the screen left side.
2. The size and position of the auto focus
frame is set at the face of the subject
automatically.
3. Press the shutter button halfway. The focus frame turns to green when
the focus is activated.
4. Press the shutter button fully to take a picture.
46 _SETUP
This function can detect up to 9 persons.
When the camera recognises many people at the same time, it will
focus on the nearest person.
The Digital zoom is not activated in this mode.
The effects functions are not activated in this mode.
When the camera detects a target face, the white colour focus
frame will be displayed over the target face and the gray colour
focus frame appear over the remaining faces(up to 8). Press the
shutter button halfway down to focus on the face and the white
focus frame turns green.(Total 9)
Return to previous AF mode if face detection was failure.
In some conditions this function cannot work properly.
- When a person wears dark glasses or some part of the face is
hidden.
- When the person being taken does not look at the camera.
- Camera doesn't detect a face as the brightness is too dark or
too bright.
- The distance between the camera and object are far.
The maximum available Face Recognition range is 2.5m (Wide).
The nearer the subject, the faster the camera can recognize the
subject.
Recording ( Ò )
Voice Memo
A voice can be recorded for as long as the
available recording time (Max. 10 hour) allows.
RECORDING
Contrast
Auto Focus
Voice Memo
Voice Record
Sharpness
Normal
Contrast
Normal
Auto Focus
Off
Voice Memo
On
Voice Record
OK
Back
- If the voice memo indicator is displayed on
the LCD monitor, the setting is completed.
Set
Press the shutter button to record a voice.
- Press the shutter button once and voice
is recorded for as long as the available
recording time (max:10 hour) allows. The
recording time will be displayed on the LCD
monitor. Voice will still be recorded if the
shutter button is released.
- If you wish to stop recording, press the
shutter button again.
- File type : *.wav
- Press the shutter button and take a picture.
The picture is stored on the memory card.
- Voice memo will be recorded for ten seconds
from the moment the picture is stored. In the
middle of the sound recording, pressing the
shutter button will stop the voice memo.
SH
RECORDING
Center AF
Off
Move
OK
SH
REC
MENU Exit
Set
[Voice recording mode]
Stop
SETUP_ 47
03 SETUP
Sharpness
You can add your voice-over to a stored still
image. (Max. 10 sec.)
Voice Recording
Recording ( Ò )
Voice Recording
Recording the movie clip without voice
Pausing while recording a voice
Using this function, you can record your
favourite voice clips into a voice recording
file without having to create multiple voice
recording files.
You can record the movie without voice.
Voice Mute
SH Stop
REC
1. Press the Pause button ( Ø ) to pause
[Voice recording mode]
recording.
2. Press the Pause button ( Ø ) again to
resume the recording.
3. If you wish to stop recording, press the shutter button again.
RECORDING
Select [On] of [Voice Mute] menu in the Movie
clip mode. ( Ç ) icon will appear on the LCD
monitor. Press the Shutter button and a movie
will record for as long as the memory capacity
allows without voice.
Off
On
OK
Back
Set
A distance of 40cm between you and the camera (microphone) is the
the voice recording is cancelled.
SCENE mode
Use the menu to easily configure optimal
settings for a variety of shooting situations.
Press the MENU button and select a desired
sub menu.
Ä Refer to page 18 for more information.
48 _SETUP
RECORDING
Scene Mode
best distance to record sound.
If the camera power is turned off while the voice recording is paused,
CHILDREN
Auto Focus
LANDSCAPE
Voice Memo
Voice Record
TEXT
CLOSE UP
SUNSET
DAWM
Back
OK
Set
Sound menu
Sound ( Ó )
In this mode, you can set up sound settings. You can use the setup menu
in all camera modes, except Voice Recording mode.
The items indicated by
are default settings.
Volume
Ó
Shutter Sound
( Sound )
Beep Sound
Available mode
Page
p.49
Off
Start Sound
Low
Shutter Sound
Beep Sound
High
AF Sound
Medium
OK
Back
Set
Start up sound
p.49
You can select the sound that is activated whenever the camera is
turned on.
p.49
- Start up sound : [Off], [Sound 1], [Sound 2],
[Sound 3]
- If the start up image is set to [Off], the start
up sound will not activate, even though you
may have set these to on.
SOUND
Volume
Start Sound
Off
Shutter Sound
Beep Sound
Sound 2
AF Sound
Sound 3
Sound 1
OK
Back
Set
p.50
Shutter sound
You can select the shutter sound.
p.50
On
Volume
Off
AF Sound
SOUND
- [Volume] sub menu : [Off], [Low],
[Medium], [High]
SOUND
- Shutter sound : [Off], [Sound 1],
[Sound 2], [Sound 3]
Volume
Start Sound
Shutter Sound
Start Sound
Off
Low
Medium
High
Off
Sound 1
Sound 2
Sound 3
Off
Sound 1
Sound 2
Sound 3
Off
Sound 1
Sound 2
Sound 3
Beep Sound
AF Sound
Off
Sound 1
Sound 2
Sound 3
Back
OK
Set
SETUP_ 49
03 SETUP
Volume
Sub Menu
Menu
Mode
You can select a volume of start up sound, shutter sound, beep sound
and AF sound.
Sound ( Ó )
Setup menu
Beep Sound
In this mode, you can set up basic settings. You can use the setup menu
in all camera modes, except Voice Recording mode.
The items indicated by
are default settings.
If you set sound to ON, various sounds will be activated for camera
startup, when buttons are pressed, so that you can be aware of the
camera operation status.
Mode
File
Reset
Page
Series
p.51
SOUND
Volume
Start Sound
Shutter Sound
Beep Sound
- [Beep Sound] sub menu : [Off], [Sound 1, 2, 3]
Sub menu
Menu
AF Sound
Off
Sound 1
Sound 2
Sound 3
OK
Back
Language
Set
p.52
AF sound
If you set AF sound to ON, AF sound will be activated when a subject is
focused so that you can be aware of the camera operation status.
Ù
- [AF sound] sub menu : [Off], [On]
SOUND
Volume
Beep Sound
AF Sound
Back
( Setup
menu 1 )
Start Sound
Shutter Sound
Date & Time
Off
On
OK
Set
World Time
50 _SETUP
yy/mm/dd
mm/dd/yy
dd/mm/yy
Off
London
Rome,Paris,Berlin
Athens. Helsinki
Moscow
Teheran
Abu Dhabi
Kabul
Tashkent
Mumbay, New Delhi
Kathmandu
Almaty
Yangon
Bankok, Jakarta
Beijing, Hong Kong
Seoul, Tokyo
Darwin, Adelaida
Guam, Sydney
Okhotsk
Wellington, Auckland
Samoa, Midway
p.52
p.52
Setup menu
Menu
Ù
( Setup
menu 1 )
Imprint
LCD
AF Lamp
Start Image
Quick View
Ú
( Setup
menu 2 )
Power Off
Page
Honolulu, Hawaii
Alaska
LA, San Francisco
Denver, Phoenix
Chicago, Dallas
New York, Miami
Caracas, La Paz
Newfoundland
Buenos Aires
Mid-Atlantic
Cape Verde
-
Off
Date
Date&Time
-
Dark
Normal
Bright
-
Off
On
Off
Logo
User Image
-
Off
0.5 sec
1 sec
3 sec
Off
1 min
3 min
5 min
10 min
-
This function allows the user to select the file naming format.
[Reset]
p.52
p.53
p.53
p.53
p.53
p.54
p.54
LCD Save
Off
On
p.54
Video Out
NTSC
PAL
p.55
Format
No
Yes
p.56
Reset
No
Yes
p.56
Battery Type
Alkaline
Ni-MH
p.56
Ä Menus are subject to change without prior notice.
File name
: After using the reset function, the
next file name will be set from
SETUP 1
Reset
0001 even after formatting, delet- File
Language
Series
ing all or inserting a new memory Date&Time
World Time
card.
Imprint
LCD
[Series]
: New files are named using
OK Set
Back
numbers that follow the previous
sequence, even when a new
memory card is used, or after formatting, or after deleting
all pictures.
- The first stored folder name is 100SSCAM, and the first file name is
SN850001.
- File names are assigned sequentially from SN850001 " SN850002
" ~ " SN859999.
- The folder number is assigned sequentially from 100 to 999 as
follows: 100SSCAM " 101SSCAM " ~ " 999SSCAM.
- Maximum numbers of files in a folder are 9999.
- The files used with the memory card conform to the DCF (Design rule
for Camera File systems) format. If you change the image file name,
the image may not play back.
SETUP_ 51
03 SETUP
World Time
Sub menu
Mode
Setup menu 1 ( À )
Setup menu 1 ( À )
LANGUAGE
World Time
There is a choice of languages that can be displayed on the LCD monitor.
Even if the battery is removed and inserted again, the language setting will
be preserved.
The date and time selected in the [Date&Time] serve as the date and time
of your present location. Setting [World Time] enables you to display the
local date and time on the LCD monitor when travelling overseas.
SETUP 1
File
Language
Date&Time
- LANGUAGE sub menu
: English, Korean, French, German, Spanish, Italian, S.Chinese, T.Chinese, Russian,
Portuguese, Dutch, Danish, Swedish,
Finnish, Thai, Bahasa (Malay / Indonesian),
Arabic, Czech, Polish, Hungarian and
Turkish.
ENGLISH
䚐ạ㛨
FRANÇAIS
World Time
DEUTSCH
Imprint
LCD
ESPAÑOL
ITALIANO
OK
Back
Set
Setting up the Date / Time / Date type
You can change the date and time that will be displayed on the
captured images and set up the date type.
SETUP 1
File
Language
Date&Time
World Time
Imprint
LCD
52 _SETUP
Back
07/08/01
- Date type : [yy/mm/dd], [mm/dd/yy],
[dd/mm/yy], Off],
13:00
yy/mm/dd
OK
Set
- Available cities:
London, Cape Verde, Mid-Atlantic, Buenos
SETUP 1
Aires, Newfoundland, Caracas, La Paz,
NewYork, Miami, Chicago, Dallas, Denver,
Phoenix, LA, Sam Francisco, Alaska, Honolulu, Hawaii, Samoa, Midway, Wellington,
Seoul, Tokyo
[ GMT +09:00 ] 2007 /08 / 01 13:00
Auckland, Okhotsk, Quam, Sydney, Darwin
OK Confirm
Adelaide, Seoul, Tokyo, Beijing, Hon Hong,
Bankok, Jakarta, Yangon, Almaty, Kathmandu, Mumbai, New Delhi,
Tashkent, Kabul, Abu Dhabi, Teheran, Moscow, Athens, Helsinki,
Rome, Paris, Berlin
Setup menu 1 ( À )
You can turn on and off the Auto Focus lamp.
- Sub menus
[Off]
- Sub menus
[Off]
: The AF lamp will not light up
in low light conditions.
[On]
: The AF lamp will light up in
low light conditions.
SETUP 1
File
Language
Date&Time
World Time
Off
Imprint
Date
LCD
Date&Time
OK
Back
You can adjust the LCD brightness.
- Sub menus : [Dark], [Normal], [Bright]
SETUP 1
Language
World Time
Imprint
LCD
Back
Date&Time
World Time
Imprint
AF Lamp
Set
LCD brightness
Date&Time
Language
LCD
The Date & Time are imprinted at the bottom right side of the still image.
The imprint function is applied only to still images except for the images
taken in photo frame effect mode.
Depending on the manufacturer and print mode, the date printed on an
image may not be printed correctly.
File
SETUP 1
Off
On
OK
Back
Set
Start up image
You can select the image that is first displayed on the LCD monitor
whenever the camera is turned on.
- Sub menus : [Off], [LOGO], [User Image]
- Use a saved image for the start-up image
with the [Start Image] in the [RESIZE] menu
in the play mode.
- The start-up image will not be deleted by
[Delete] or [Format] menu.
- The User images will be deleted by [Reset]
menu.
SETUP 1
Date&Time
World Time
Imprint
LCD
AF Lamp
Start Image
: The DATE & TIME will not be
imprinted on the image file.
[Date]
: Only the DATE will be imprinted on the image file.
[Date&Time] : The DATE & TIME will be
imprinted on the image file.
Auto Focus lamp
There is an option to include DATE / TIME on still images.
03 SETUP
Imprinting the recording date
Back
Off
OK
Set
Dark
Normal
Bright
OK
Set
SETUP_ 53
Setup menu 2 ( Á )
Quick view
Auto power off
If you enable Quick View before capturing an image, you can view the
image you just captured on the LCD monitor for the duration set in the
[Quick View] setup. Quick view is possible only
with still images.
This function switches the camera off after a set amount of time in order
to prevent unnecessary battery drainage.
: The quick view function
can’t be activated.
: The captured image is
briefly displayed during
the selected time.
SETUP 2
[0.5, 1, 3 sec]
: The power off function will SETUP 2
Quick View
not operate.
Power Off
Off
[1, 3, 5, 10 min] : The power will turn off
LCD Save
1 min
3 min
Video Out
automatically if not used
Format
5 min
10 min
Reset
for the period of time
OK Set
Back
specified.
- After replacing the battery, the power off setting will be preserved.
- Note that the automatic power off function will not operate if the
camera is in the PC / Printer mode, slide show, playing back a voice
recording and playing back a movie clip.
- Sub menus
[Off]
- Sub menus
[Off]
Off
Power Off
0.5 sec
LCD Save
Video Out
1 sec
3 sec
Format
Quick View
Reset
Back
OK
Set
LCD save
If you set the [LCD save] to On and the camera isn't operated during the
specified time, the LCD monitor will be turned off automatically.
54 _SETUP
SETUP 2
Quick View
Power Off
LCD Save
- Sub menus
[Off]
: The LCD monitor will not be
turned off.
[On]
: If the camera isn't operated during the specified time (about 30
SEC.), the camera power will be
idle (Camera status lamp:Blinking)
automatically.
Off
Video Out
On
Format
Reset
Back
OK
Set
Setup menu 2 ( Á )
- NTSC
- PAL
Selecting Video out type
SETUP 2
Quick View
Power Off
LCD Save
Video Out
Format
Connecting to an external monitor
When the camera is connected to an external
monitor, the image and menus on the LCD
monitor will be visible on the external monitor
and the LCD monitor of the camera.
NTSC
PAL
Reset
Back
OK
Set
Yellow - Video
White - sound
SETUP_ 55
03 SETUP
The Movie output signal from the camera can be NTSC or PAL.
Your choice of output will be governed by the type of device (monitor or
TV, etc.) to which the camera is connected. PAL mode can support only
BDGHI.
: U.S.A, Canada, Japan, South Korea, Taiwan, Mexico.
: Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K., Holland, Italy, Kuwait, Malaysia, New Zealand,
Singapore, Spain, Sweden, Switzerland, Thailand, Norway.
- When using a TV as an external monitor, you will need to select the
external or AV channel of the TV.
- There will be a digital noise on the external monitor, but it is not a
malfunction.
- If the image is not in the centre of the screen, use the TV controls to
centre it.
- When the camera is connected to an external monitor, some parts of
the image may not be displayed.
- When the camera is connected to an external monitor, the menu will be
visible on the external monitor and the menu functions are the same as
those indicated on the LCD monitor.
Setup menu 2 ( Á )
Formatting a memory
Initialisation
This is used for formatting the memory. If you run [Format] on the memory,
all images, including the protected images, will be deleted. Be sure to
download important images to your PC before formatting the memory.
All camera menu and function settings will be restored to their default
values. However, values for DATE / TIME, LANGUAGE, and VIDEO OUT
will not be changed.
- Sub menus
[No]
: The memory will not be formatted.
[Yes]
: A window for confirming the selection displays. Select the [Yes]
menu. A [Processing!] message
appears and the memory will be
formatted. If you run FORMAT in
Play mode, a [No Image!] message
will appear.
- Sub menus
[No]
: Settings will not be restored to
their defaults.
[Yes]
: A window to confirm the selection will be displayed. Select the
[Yes] menu and all settings will be
restored to their defaults.
Quick View
Power Off
LCD Save
Video Out
Format
Reset
Back
No
Yes
OK
Set
SETUP 2
Quick View
Power Off
LCD Save
Video Out
Format
SETUP 2
Reset
No
Yes
OK
Back
Set
Selecting a battery type
If a battery type is selected, the camera will be optimized according to the
selected battery type.
[Battery Type] sub Menu : Alkaline / Ni-MH
SETUP 2
Power Off
Format
Reset
Battery Type
56 _SETUP
LCD Save
Video Out
Back
Be sure to run [Format] on the following types of memory card.
- A new memory card, or an unformatted memory card
- A memory card that has a file this camera can't recognise or one that
has been taken from another camera.
- Always format the memory card using this camera. If you insert a
memory card that has been formatted using other cameras, memory
card readers, or PCs, you will get a [Card Error!] message.
Alkaline
Ni-MH
OK
Set
Starting play mode
Playing back a still image
1. Select the PLAY mode by pressing the
play mode button ( Î ).
2. The last image stored on the memory is
displayed on the LCD monitor.
Playing back a movie clip
1. Select the recorded movie clip that you want
to play back by using the Left/Right button.
2. Press the play & pause button ( Ø ) to play
back a movie clip file.
- To pause a movie clip file while playing it
back, press the play & pause button again.
- Pressing the play & pause button( Ø )
again will cause the movie clip file to restart.
- To rewind the movie clip while it is playing,
press the Left button. To fast forward the
movie clip, press the Right button.
- To stop playback of the movie clip, press
the play & pause button, and then press the
Left or Right button.
Play
E
Capture
3. Select an image that you want to view
by pressing the Left/ Right button.
Ä Press and hold the Left or Right
button to play back the images quickly.
PLAY_ 57
04 PLAY
Turn the camera on and select Play mode by pressing the play mode
button ( Î ). The camera can now play back the images stored in the
memory.
If the memory card is inserted in the camera, all the camera
functions apply only to the memory card.
If the memory card is not inserted in the camera, all the camera functions
apply only to the internal memory.
Starting play mode
Movie clip capture function
On camera movie trimming
You can capture still images from the movie clip.
You can extract desired frames of movie clip during the movie clip play
back. If the running time is under 10 seconds, the movie clip can’t be
trimmed.
How to capture the movie clip
1. Press the Play / Pause button( Ø ) while
playing the movie clip. Then press the E
button.
2. The paused movie clip is saved in a new file
name.
The captured movie clip file is the same
size as the original movie clip (640x480,
320x240).
When you press the E button at the
beginning of the movie clip, the first frame of
the movie clip will be saved as a still image.
T Trim
E Capture
[Paused]
[Press the E button]
1. Press the Pause button( Ø ) at the point
of the movie clip where you want to start
extracting.
2. Press the T button.
3. Press the Play & Pause button( Ø ) and
the extracted range will be displayed on
the status bar.
4. Press the Play & Pause button( Ø )
once more at the point where you wish the
extracted file to stop.
5. Press the T button and a confirmation
window will be displayed.
6. Select a desired sub menu by pressing the
Up/Down button and press the OK button.
[No] : The movie trimming will be cancelled.
[Yes] : The extracted frames are saved
as a new file name.
T Trim
E Capture
T Trim
Trimming?
No
Yes
OK
Confirm
If you don't specify the ending point of the movie clip, the
trimming confirmation window will be displayed at the point of the last
frame.
58 _PLAY
Starting play mode
Playing back a voice memo
1. Select the recorded voice that you want to
play back by using the Left/Right button.
2. Press the play & pause button ( Ø ) to
play back a recorded voice file.
- To pause a recorded voice file, while playing it back, press the play & pause button
Play
again.
- To resume playback of the voice file, press
the play & pause button
- To rewind the voice file while it is playing, press the Left button.
To fast forward the voice file, press the Right button.
- To stop playback of the voice memo, press the play & pause button
and then press the MENU/OK button.
1. Select a still image that has the voice memo.
2. Press the play & pause button ( Ø ) to play
back the voice memo.
- To pause the voice memo, while playing it
back, press the play & pause button
( Ø ) again.
- To resume playback of the voice memo,
press the play & pause button.
- To stop playback of the voice memo, press
the play & pause button and then press the
MENU / OK button.
04 PLAY
Playing back a recorded voice
REW
FF
Pause
OK Stop
Play
PLAY_ 59
LCD monitor Indicator
Using the camera buttons to set the camera
The LCD monitor displays shooting information about the displayed image.
In Play mode, you can use the buttons on the camera to conveniently set
up the Play mode functions.
Thumbnail ( º ) / Enlargement ( í ) button
You can view multiple pictures, enlarge a selected picture, and crop and
save a selected area of an image.
No.
1
2
3
4
5
6
7
8
9
10
11
Description
Playback mode
Memory card indicator
Folder name & File name
Battery
ISO
Aperture value
Shutter speed
Flash
Image size
Recording date
DPOF
12
13
Protect
Voice Memo / Movie Clip
60 _PLAY
Icon
Î
Ö/×
100-0010
f g h i
50 ~ 1600
F2.8 ~ F4.6
15 ~ 1/2000
ON / OFF
3264x2448 ~ 320X240
2007/08/01
Ñ
Ð
Ï/´
Page
p.57
p.51
p.12
p.42
p.17
p.17
p.26
p.39
p.52
p.79
p.79
p.47/57
Thumbnail display
1. While an image is displayed on full screen,
press the thumbnail button.
2. The thumbnail display will highlight the image
that had been showing at the time the thumbnail mode was selected.
3. Press the 5 function button to move to a
desired image.
4. To view an image separately, press the enlargement button.
Pressing the thumbnail
button ( º )
Pressing the enlargement
button ( í )
Highlighted image
[Highlighted image]
[ Thumbnail display mode ]
Thumbnail ( º ) / Enlargement ( í ) button
Image enlargement
The maximum enlargement rate in proportion to the image size
Image size
Ÿ
¬
­
✩
✨
✧
Maximum
enlargement
rate
X12.0
X11.3
X9.5
X9.0
X8.0
X4.0
Trimming : You can extract part of the image that you want and save it
separately.
1. Select an image that you want to enlarge
and press the enlargement button.
Press the MENU/OK button and a message
Trimming?
will be displayed.
No
Yes
2. Select a desired sub menu by pressing the
Up / Down button and press the OK button.
OK Confirm
- [No] : The trimming menu will disappear.
- [Yes] : The trimmed image will be saved
as a new file name, and appear on the LCD monitor.
Ä If there is not enough memory space to save the trimmed image, the
image can’t be trimmed.
PLAY_ 61
04 PLAY
1. Select an image that you want to enlarge
and press the enlargement button.
2. Different parts of the image can be viewed
by pressing the 5 function button.
3. Pressing the thumbnail button will zoom
back to the original full sized image.
- You can tell whether the image displayed
is an enlarged view by checking the image
enlargement indicator shown at the top
left of the LCD monitor. (If the image is not
an enlarged view, the indicator will not be
displayed.) You can also check the area of
enlargement.
- Movie clips and WAV files can’t be enlarged.
- If an image is enlarged, a loss of quality may occur.
Info( î ) / Up button
Play & Pause ( Ø ) / Down button
When the menu is displayed on the LCD monitor, the UP button operates
as a direction button.
When the menu is not displayed on the LCD monitor, pressing the Info button will display image information on the LCD monitor.
In Play mode, the play & pause/ down button works as follows:
Info ( î ) button
Info ( î ) button
- If the menu is displayed
Press the DOWN button to move from the main menu to a sub menu,
or to move down the sub menu cursor.
- If a still image with a voice memo, a voice file, or a movie clip is playing
·In Stop mode
: Plays a still image with a voice memo, a voice
file, or a movie clip.
·During playback
: Temporarily stops playback.
·In Pause mode
: Resumes playback
Info ( î ) button
Play
[ Voice recording is stopped ]
62 _PLAY
Pause
[ Voice recording is playing ]
OK Stop
Play
[ Voice recording is paused ]
Left / Right / Menu / OK button
Delete ( Õ ) button
LEFT / RIGHT / MENU / OK buttons activate the following.
This deletes images stored on the memory card.
- LEFT button
- MENU button
- OK button
Printer ( » ) button
When the camera is connected to a PictBridge printer, you can print images by pressing the Printer button.
Print
1. Select an image that you want to delete by pressing the Left / Right
button and press the DELETE ( Õ ) button.
T
Select
Delete ?
Delete ?
No
Yes
No
Yes
OK Confirm
[Single Image]
04 PLAY
- RIGHT button
: While the menu is showing, the LEFT button
operates as a direction button. While the menu
is not showing, press the LEFT button to select
the previous image.
: While the menu is showing, the RIGHT button
operates as a direction button. While the menu
is not showing, press the RIGHT button to
select the next image.
: When you press the MENU button, the play
mode menu will be displayed on the LCD monitor. Pressing it again will return the LCD to the
initial display.
: When the menu is displayed on the LCD monitor, the OK button is used for confirming data
that is changed by using the 5 function button.
OK Confirm
[Thumbnail Image]
2. To delete images, press the T button.
- Left/Right button : Selects images
- T button
: checks for deletion
- OK button
: deletes the selected
images.
Prev
T
Select
Next
OK Delete
3. Select the submenu values by pressing the Up / Down button and then
press the OK button.
- If [No] is selected : cancels "Delete Image".
- If [Yes] is selected : deletes the selected images.
OK Menu
PLAY_ 63
E (Effect) button : Resize
Change the resolution (size) of pictures taken. Select [Start image] to save
an image to be the start-up image.
1. Press the play mode button and press the
E button.
2. Press the Left / Right button and select
the [RESIZE] ( ñ ) menu tab.
3. Select a desired sub menu by pressing the
Up / Down button and press the OK button.
RESIZE
Move
Image Resize Types
Ÿ
✩
✨
✧
¬
­
64 _PLAY
Exit
E
( o : Selectable)
✩
✨
✧
ð
o
o
o
o
o
o
o
o
o
o
“
’
‘
ð
o
o
o
o
}
{
ð
o
o
o
- A large sized image can be resized to a smaller sized image, but not
vice versa.
- Only JPEG images can be resized. Movie clip (AVI), Voice recording
(WAV) files can’t be resized.
- You can change the resolution of only those files compressed in the
JPEG 4:2:2 format.
- The resized image will have a new file name. The [Start Image] image is
stored not on the memory card but on the internal memory.
- If a new user image is saved, one of the two user images will be deleted
in order.
- If the memory capacity is insufficient to store the resized image, a
[Memory Full!] message will appear on the LCD monitor and the resized
image can't be stored.
E (Effect) button : Colour
You can rotate the stored images by various degrees.
It is possible to add colour effects to your images by using this button.
1. Press the play mode button and press the
E button.
2. Press the LEFT / RIGHT button and select the
[ROTATE] ( ò ) menu tab.
3. Select a desired sub menu by pressing the UP
/ DOWN button.
1. Press the play mode button and press the E button.
2. Select ( æ ) menu tab by pressing the
Left / Right button.
COLOR
ROTATE
Move
E
Exit
Left 90°
Right 90°
180°
E Back
[ ô : Right 90˚]
: Rotate picture in a
clock-wise direction
OK Set
E Back
OK Set
[ ó : Left 90˚]
: Rotate picture in a counterclock-wise direction
Horizontal
Move
E
Exit
3. Select a desired sub menu by pressing the Up / Down button and
press the OK button.
Icon
OK Set
04 PLAY
E (Effect) button : Rotating an image
Descroption
E Back
[ õ : 180˚]
: Rotate picture 180 degrees
Vertical
Û
Captured images will be stored in black and white.
Ü
Captured images will be stored in a sepia tone
(a gradient of yellowish brown colours).
Þ
Captured images will be stored in a red tone.
ß
Captured images will be stored in a green tone.
Ý
Captured images will be stored in a blue tone.
Save the image in negative mode.
OK Set
E Back
[ ö : Horizontal]
: Rotate picture horizontally
OK Set
E Back
[ ❶ : Vertical]
: Rotate picture vertically
§
Captured images will be stored in set RGB tone.
4. The changed image is saved as a new file name.
4. The changed image is saved as a new file name.
If you display the rotated image on the LCD monitor, empty spaces
may appear to the left and right of the image.
PLAY_ 65
E (Effect) button : Special Colour
E (Effect) button : Colour
Custom colour
You can change the R (Red), G (Green) and B
(Blue) values of the image.
1. Press the play mode button and press the E button.
2. Select ( * ) menu tab by pressing the Left/Right button.
Custom Color
Colour Filter
Move
- OK button
- Up / Down button
- Left / Right button
: Select / setup the
Custom Colour
: Selects R, G, B
: Change the values
OK Set
Custom Color
With this menu, you can change the colour information of the
image (excluding Red, Blue, Green and Yellow) to Black and White.
1. Select ( ½ ) by pressing the Up/Down button.
SPECIAL COLOR
Move
Color Filter
OK Set
Move
E
Exit
OK Set
E
Back
2. Press the OK button and the image is saved as a new file name.
66 _PLAY
E (Effect) button : Special Colour
Colour mask
With this menu, you can select a part you want to highlight. The rest of the image will be in black and white.
04 PLAY
SPECIAL COLOR
Color Mask
Select ( ¾ ) the selected area will be
shown.
Move
E
Press the OK button and you can set the
size and location of the part to be highlighted.
Exit
OK Set
E Back
Move
OK Set
TW Size
W / T button : Changing size of
selected part
Move
Press the OK button twice and the colour
masked image will be saved as a new file name.
OK Set
TW Size
Up/Down/Left/Right button:
Changing the location
[Final image]
Move
OK Set
TW Size
PLAY_ 67
E (Effect) button : Image editing
Contrast control
1. Press the play back button and press the E button.
2. Select ( + ) menu tab by pressing the Left/Right button.
You can change the contrast of the image.
1. Select ( , ) by pressing the Up/Down button and a bar for selecting the
contrast will be displayed.
2. Change the contrast by pressing the Left/
Right button.
3. Press the OK button and the image will be
saved as a new file name.
Red eye Removal
Red eye effect can be removed from the captured image.
1. Select ( ! ) by pressing the Up/Down button and press the OK button.
2. The [Processing!] message displays and the
image is saved as a new file name.
Red Eye Fix
Move
E
Back
Set
OK
Set
You can change the saturation of the image.
) by pressing the Up/Down
1. Select (
button and a bar for selecting the saturation
will be displayed.
2. Change the saturation by pressing the
Left/Right button.
3. Press the OK button and the image will be
saved as a new file name.
Brightness control
You can change the brightness of the image.
Brightness
Saturation
Move
Noise Effect
You can add noise to an image to add a more classic feel to your photo.
Move
OK
Set
1. Select ( ¿ ) by pressing the Up/Down button and press the OK button.
2. The [Proccessing!] message be displayed
and the image is saved as a new file name.
Add Noise
OK
68 _PLAY
OK
Saturation control
OK Set
1. Select ( z ) by pressing the Up/Down button and a bar for selecting the brightness
will be displayed.
2. Change the brightness by pressing the
Left/Right button.
3. Press the OK button and the image will be
saved as a new file name.
Contrast
Set
E
Back
E (Effect) button : FUN
Cartoon
You can add a text box to the image to make the image cartoon like.
Ä The cartoon image is saved as 1M image size.
Select a desired frame by
pressing the Left/Right
button and then press the OK
button
Select Cartoon ( ¯ )
Move
EE
Frame
Exit
E Set
OK
Select
EE
Back
E Set
OK
Move
OK
E Set
Change the location of the
text box by pressing the
Left/Right button.
Press the OK button and the
image is saved. Press the OK
button again to open a new
image to save.
OK
Move
OK Search
E
Fn
Delete
Select an image by pressing the Up/Down/Left/Right button
and press the OK button.
Select the third image with the same procedure.
Press the OK button and the file is
saved as a new file name.
Select the position of image and
text box with the same procedure.
Move
E Set
OK
OK
Save
E
Fn
Delete
PLAY_ 69
04 PLAY
Select a desired position
by pressing the Up/Down/
Left/Right button and press
the OK button.
Cartoon
FUN
E (Effect) button : FUN
Before saving the cartoon image, you can change the selected
image.
Preset focus frames
You can make the subject stand out from its surroundings. The subject
will be sharp and in focus while making the rest out of focus.
1. Pressing the Fn button deletes the images in order.
2. Press the OK button and you can select images.
FUN
High Light
Pressing the Fn button
OK
Save
E
Fn
Delete
OK Search
E
Fn
Delete
3. After selecting desired images, press the OK button to save the
image as a new file name.
Move
Range
Exit
E Set
OK
Select a desired frame by pressing the Left/Right button and press the
OK button.
High Light
High Light
Range
E Set
OK
[Range 1]
70 _PLAY
EE
High Light
Range
E Set
OK
[Range 2]
High Light
Range
E Set
OK
[Range 3]
Range
E Sets
OK
[Range 4]
E (Effect) button : FUN
Composite image
Moving and changing the focus frame
You can change the focus frame after selecting a Range menu.
You can combine 2 - 4 different shots in a still image.
Composite
FUN
Move
High Light
04 PLAY
1. Select a focus frame by pressing the Left/Right button and press the
OK button.
2. Move the location of the frame by pressing the Up/Down/Left/Right
button.
3. Press the OK button and the file is saved as a new file name.
EE Exit
Composite
E Set
OK
Move
E Set
OK
Pressing the
OK button
Range
Move
E Set
OK
E Save
OK
[The frame is activated]
Press the OK button.
(You can select 2-4 composite images)
Pressing Up/
Down/Left/Right
button
If you press the Shutter and Play mode button, a capture mode is
Pressing the
OK button
executed.
The composite image is saved as 1M image size.
Move
E Save
OK
[After changing the frame
position]
PLAY_ 71
E (Effect) button : FUN
Ä Selecting 2 composite shots
Before selecting the last composite image, you can change a part of
composite image.
Pressing the
Up/Down/Left/Right button
Move
1. During the composite image editing, press the Fn button.
2. A previous image will be deleted. Press the OK button and you can
select a new image. After selecting an image, press the Fn button
again and the image will be deleted again.
E Set
OK
Move
E Set
OK
[Changing the position]
Pressing the
OK button
Pressing the Fn
button
OK Search
Pressing the
OK button
E Delete
Fn
[Before selecting the
3rd image]
OK Search
[Moving backward to the
2nd image]
3. Press the OK button and you can select an image again.
OK Search
EE Back
OK Search
E Delete
Fn
[Selecting the second image]
Select an image by pressing the 5 function button and press the OK button
Change the location of second image by pressing the
Up/Down/Left/Right button and press the OK button
to save the image.
Move
72 _PLAY
OK Save
E Delete
Fn
E Delete
Fn
E (Effect) button : FUN
Photo Frame
FUN
04 PLAY
You can add 9 types of frame-like borders to a still image you want to
capture.
Date & Time information will not be printed on the stored image taken with
Photo Frame menu.
Photo Frame
Move
EE Exit
Frame
E Set
OK
Select a desired sub menu by pressing the Left/Right button.
- Press the E button and the frame will be canceled.
Press the OK button and the image is saved.
PLAY_ 73
E (Effect) button : FUN
Setting up the play back function using the LCD monitor
Sticker
PLAY mode functions can be changed by using the LCD monitor.
In the PLAY mode, pressing the MENU button displays the menu on the
LCD monitor. The menus you can set up in Play mode are as follows. To
capture an image after setting up the play menu, press the PLAY mode
button or shutter button.
You can add various stickers to the image.
FUN
Sticker
Select ( ¨ )
Menu Tab
Move
E
Sticker
Exit
OK
Set
Select a desired sticker
by pressing the Left/Right
button and press the OK
button
OK Save
Move
Fn
Add
Select a location of
sticker by pressing the
Up/Down/Left/Right
button
SLIDE
SHOW
❸)
(
Main Menu
Sub Menu
Secondary Menu
Show
Play / Repeat Play
-
All
Date
Select
-
Images
Effect
the Fn button.
Press the OK button to store the image.
Classic
Delignt
1, 3, 5, 10 sec
Music
Off / Music 1, 2, 3
-
Off
-
On
-
Voice Memo
p.76
-
p.77
p.78
OK Save
Move
Fn
Add
PLAY
BACK
(
Protect
ø)
DPOF
Copy To Card
74 _PLAY
Basic
Rhythmic
Interval
Delete
Ä You can add additional stickers by pressing
Off
Memories
Page
Select
-
All
No / Yes
Select
All
Unlock / Lock
p.79
Standard
Select / All / Cancel
Index
No / Yes
Size
Select / All / Cancel
p.79
~
p.81
No
-
Yes
-
p.78
p.81
Setting up the play back function using the LCD monitor
This menu is available while the camera is connected to a PictBridge
supporting printer (direct connection to the camera, sold separately) with a
USB cable.
Menu Tab
Main Menu
Size
❹
Layout
Secondary Menu
One Pic
-
All Pics
-
Main Menu
Type
Page
p.83
Sub Menu
Secondary Menu
Auto
-
Plain
-
Photo
-
FastPhoto
-
Auto
-
Draft
-
Auto
-
PostCard
-
Card
-
4X6
-
L
-
2L
-
Letter
-
Auto
-
A4
-
Off
-
A3
-
On
-
Auto
-
Full
-
1
-
2
-
4
-
8
-
9
-
16
-
Index
-
Quality
❹
Date Print
File Name
p.84
Reset
Normal
-
Fine
-
Auto
-
Off
-
On
-
No
-
Yes
-
Page
04 PLAY
Images
Sub Menu
Menu Tab
p.84
Ä Menus are subject to change without prior notice.
PLAY_ 75
Starting the slide show ( ❸ )
Images can be displayed continuously at pre-set intervals.
You can view the slide show by connecting the camera to an
external monitor.
1. Press the play mode button and press the menu button.
2. Press the LEFT / RIGHT button and select the [SLIDE SHOW] menu tab.
Start the slide show
The slide show can start only in the [Show] menu.
1. Use the Up / Down buttons to select the
[Show] menu and press the Right button.
SLIDE SHOW
2. Select a desired sub menu by pressing the
Show
Play
Image
Repeat Play
Up / Down button.
Effect
[Play]
: The slide show is closed
Interval
Music
after one cycle.
Back
OK Set
[Repeat Play] : The slide show is repeated until cancelled.
3. Press the OK button and the slideshow will
be started.
- To pause the slide shown while playing it back, press the play &
pause( Ø ) button again.
- Pressing the play & pause( Ø ) button again will cause the slide
show restart.
- To stop playback of the slide show, press the play & pause
( Ø ) button, and then press the OK / Menu button.
76 _PLAY
Selecting Images
You can select image to view
1. Use the Up / Down buttons to select the
[Image] menu and press the Right button.
SLIDE SHOW
2. Select a desired sub menu by pressing the
Show
Image
Up / Down button.
Effect
[All]
: All images saved in the Memory Interval
Music
are played back.
Back
[Date] : Images taken in a specified date
are played back.
[Select] : You can select desired images to play back
3. Press the OK button and the settings are saved.
All
Date
Select
OK
Set
Starting the slide show ( ❸ )
Configure slide show effects
Setting play interval
Unique screen effects can be used for the slide show.
Set the slide show play interval.
SLIDE SHOW
Show
Image
Effect
Interval
Music
Off
Basic
Classic
Memories
Rhythmic
Delight
OK Set
2. Use the Up / Down button to select the
type of effect.
[Off]
: No effect.
Back
[Basic]
: Fade In/Out effect is added
and the Images are displayed at set interval.
[Classic]
: You can add noise to the image to give a classic feel.
[Memories] : Scratches are added to give an old movie effect.
[Rhythmic]
: Images are displayed with a special effect.
[Delight]
: Images are displayed with a special effect.
3. Press the OK button to confirm the setting.
1. Select the [Interval] sub menu by
pressing the UP / DOWN button and press
the RIGHT button.
2. Use the Up / Down buttons to select the
desired interval.
3. Press the OK button to save the
configuration.
SLIDE SHOW
Show
Image
Effect
Interval
Music
Back
1 sec
3 sec
5 sec
10 sec
OK Set
The loading time depends on the image size and quality.
While the slide show is playing, only the first frame of a MOVIE file is
displayed.
While the slide show is playing, the voice recording file will not display.
The interval menu functions in the [Off], [Basic] and [Classic] menu only.
Setting Background Music
Set the slide show music.
1. Select the [Music] sub menu by
pressing the UP / DOWN button and press
the RIGHT button.
2. Use the Up / Down buttons to select the
desired Music.
3. Press the OK button to save the
configuration.
SLIDE SHOW
Show
Image
Effect
Interval
Music
Back
Off
Music 1
Music 2
Music 3
OK Set
PLAY_ 77
04 PLAY
1. Select the [Effect] sub menu by
pressing the UP / DOWN button and press
the RIGHT button.
Playback ( ø )
Voice memo
Deleting images
You can add your voice to a stored still image.
This deletes images stored on the memory.
PLAYBACK
Voice Memo
Delete
Protect
DPOF
Copy to Card
Back
Off
On
OK
Set
[Voice memo menu]
SH REC
SH Stop
[Ready for recording]
[Voice is recording]
- Press the shutter button to take a picture. The images are saved on the
memory. After saving the image, the voice will record for 10 seconds.
- To stop the recording, press the shutter button.
1. Press the Up / Down button and select the
[Delete] menu tab. And then press the Right PLAYBACK
Voice Memo
button.
Delete
Select
Protect
All
2. Select a desired sub menu by pressing the
DPOF
UP / DOWN button and press the OK butCopy to Card
ton.
Back
OK Set
[Select] : Selection window for an image to
delete is displayed.
- Up/ Down/ Left/ Right : Select an image
- Zoom T Button
: Select the image for
deletion. ( Ë mark)
T Select
- OK Button : Press the OK button to display
OK Delete
the confirmation message. Select the [Yes] menu and press
the OK button to delete marked
Delete All?
images.
No
Yes
[All] : Displays confirmation window. Select
the [Yes] menu and press the OK button
Confirm
OK
to delete all unprotected images. If there
aren’t protected images, all the images
are deleted and a [No Image!] message
will appear.
3. After deletion, the screen will be changed to the play mode screen.
Of all the files stored in the memory card, the unprotected files in the DCIM subfolder
78 _PLAY
will be deleted. Remember that this will permanently delete unprotected images.
Important shots should be stored on a computer before deletion takes place. The
startup image is stored in the camera's internal memory (i.e., not on the memory
card) and it will not be deleted even if you delete all files on the memory card.
Playback ( ø )
DPOF
This is used to protect specific shots from being accidentally erased (Lock).
It also unprotects images that have been previously protected (Unlock).
DPOF(Digital Print Order Format) allows you to embed
printing information on your memory card’s MISC folder. Select the
pictures to be printed and how many prints to make.
1. Press the Up / Down button and select
the [Protect] menu tab. And then press the
Right button.
The DPOF indicator will display on the LCD monitor when an
image that has DPOF information plays back. Images can then be
printed on DPOF printers, or at an increasing number of photo labs.
2. Select a desired sub menu by pressing the
UP / DOWN button and press the OK button.
[Select ] : Selection window for an image
to be protected / released is
displayed.
- Up / Down / Left / Right : Select an image
- Zoom W / T Button : Protect / release the
image
- OK button : Your changes will be saved
and the menu will disappear.
[All] : Protect / release all saved images
- If you protect an image, the protect icon
will be displayed on the LCD monitor. (An
unprotected image has no indicator)
- An image in LOCK mode will be protected
from the delete function or [Delete] functions, but will NOT be protected from the
[Format] function.
PLAYBACK
Voice Memo
Delete
Protect
DPOF
Copy to Card
Select
All
Back
W
OK
Set
Unlock
OK
This function is not available for Movie clips and Voice recording files.
When the wide angle image is printed as a wide angle print, 8% of the
left and right side of the image may not be printed. Check that your
printer can support the wide angle image when you print the image.
When you print the image at a photo lab, request that the image is
printed as a wide angle image. (Some photo labs may not support the
wide angle size print.)
T
Set
Protect All?
Unlock
Lock
OK Confirm
PLAY_ 79
04 PLAY
Protecting images
Playback ( ø )
Standard
This function allows you to embed printing quantity information on a
stored image.
1. Press the Up / Down button and select the
[DPOF] menu tab. And then press the Right
button.
2. Press the Right button again and
[Standard] sub menu will display.
3. Select a desired sub menu by pressing the
Up / Down button and press the OK button.
[Select] : Selection window for an image to
print is displayed.
- Up / Down / Left / Right : Select an image to
print.
- Zoom W / T Button : Select the number of
prints.
[All] : Configure number of prints for all
pictures except movie and voice files.
- W / T button : Select a number of prints
[Cancel] : Cancel the print setup.
4. Press the OK button to confirm the setting.
If an image carries DPOF instructions, the
DPOF indicator ( Ñ ) will show.
80 _PLAY
PLAYBACK
Standard
Index
Size
1. Press the Up / Down button and select the
[DPOF] menu tab. And then press the Right PLAYBACK
Standard
button.
Index
No
2. Press the Right button again and [Index] sub Size
Yes
menu will display.
3. Select a desired sub menu by pressing the
Back
OK Set
UP / DOWN button.
If [No] is selected : Cancel the index print
setting.
If [Yes] is selected : The image will be printed in index format.
4. Press the OK button to confirm the setting.
Select
All
Cancel
Back
W
OK
0 Images
Set
T
OK Set
W
0 Images
OK
Set
Index
Images (except for movie clips and voice file) are printed as index type.
T
Playback ( ø )
Print size
You can specify the print size when printing images stored on the
memory card. The [Size] menu is available only for DPOF 1.1 compatible
printers.
Ä DPOF [Size] secondary menu : Cancel, 3X5,
4X6, 5X7, 8X10
PLAYBACK
Standard
Index
Size
Select
All
Cancel
Back
W
OK
Cancel
Set
This enables you to copy image files, movie clips and voice
recording files to the memory card.
1. Select the [Copy To Card] menu tab by
PLAYBACK
pressing the Up / Down button. And then
Voice Memo
press the Right button.
Delete
Protect
2. Select a desired sub menu by pressing the
DPOF
UP/ DOWN button and press the OK button. Copy to Card No
Yes
- [No] : Cancels "Copy to Card".
Back
OK Set
- [Yes] : All images, movie clips and voice
recording files saved in the internal
memory are copied to the memory card after the [Processing!] message is displayed. After copying has been
completed, the screen will return to play mode.
T
OK Set
W
Cancel
T
OK Set
Depending on the manufacturer and print model, cancelling
the printing may take a little longer for the printer to
process.
PLAY_ 81
04 PLAY
1. Press the Up / Down button and select the
[DPOF] menu tab. And then press the Right
button.
2. Press the Right button again and select the
[Size]. Sub menu will display.
3. Select a desired sub menu by pressing the UP
/ DOWN button and press the OK button.
[Select] : Selection window to change the
printed size of the image is
displayed.
- Up / Down / Left / Right : Select an image.
- Zoom W / T Button : Change the print size.
- OK button : Your changes will be saved and
the menu will disappear.
[All] : Change print size of all saved images.
- W / T button : Select a print size
- OK button : Confirm the changed setting.
[Cancel] : Cancel all of the print size settings.
Copy To Card
Playback ( ø )
When this menu is selected without inserting a memory card, the [No
Card] message will be displayed.
If there is not enough space available in the memory card to copy
saved images in the internal memory (About 19 MB), the [Copy To
Card] command will copy only some of the images and display [Memory
Full!] message. Then the system will return to the playback mode.
Please be sure to delete any unnecessary files to free up space before
inserting the memory card into the camera.
When you move the images that are stored in the internal memory by
doing [Copy To Card] to the card, the next number of file names will be
created in the card to avoid duplication of the file name.
- When the [Reset] of the [File] setup menu is set : The copied file
names start from after the last stored file name.
- When the [Series] of the [File] setup menu is set : The copied file
names start from after the last captured file name. After completing
[Copy To Card], the last stored image of the last copied folder is
displayed on the LCD monitor.
82 _PLAY
PictBridge
You can use the USB cable to connect this camera to a printer that
supports PictBridge (sold separately) and print the stored images directly.
Movie clips and voice files cannot be printed.
Setting up the camera for connection to
the printer
Select USB
1. Connect the camera and printer with USB
cable.
2. Select the [Printer] menu by pressing Up /
Down button and press the OK button.
Connecting the Camera to a Printer
Computer
Printer
OK
Confirm
PictBridge
PictBridge : Picture Selection
Ä If the [USB] menu is set to the [Computer], you cannot connect a
Pictbridge compatible printer to the camera through USB cable with
[Connecting Computer] message. In this case, remove the cable and
do the step 1 and 2 again.
You can select images you want to print.
Print
PICTBRIDGE
Images
Size
Layout
Type
Quality
Date
Back
One Pic
All Pic
OK Set
OK Menu
Prev SH Exit
0
0
Next
OK Set
[When [One Pic] is selected]
SH Exit
OK Set
[When [All Pics] is selected]
- Press the Up / Down button to select the number of prints.
- When [One Pic] is selected : Use the Left / Right button to select
another picture. After selecting another
picture, select the number of prints for
another picture.
- After setting the number of prints, press the OK button to save.
- Press the Shutter button to return to the menu without
setting the number of prints.
4. Press the Print button ( » ) and images will be printed.
PLAY_ 83
04 PLAY
Easy printing
When you connect the camera to printer in
the Play back mode, you can print a picture
easily.
- Pressing the printer ( » ) button :
Currently displayed image will be printed
with the printer’s default setting.
- Pressing the Left / Right button :
Selects a previous / next image.
Setting the Number of Copies to Print
1. Press the Menu button and the
PictBridge menu will display.
2. Use the Up / Down buttons to select the
[Images] menu and press the Right button.
3. Use the Up / Down buttons to select a
desired sub menu and press the OK button.
- Select [One Pic] or [All Pics]. A screen
where you can set the number of copies
to print will appear as shown below.
PictBridge : Print Setting
PictBridge : Reset
You can select the Paper Size, Print Format, Paper Type, Print Quality,
Date Print, and File Name Print menus for printed pictures.
Initialises user-changed configurations.
1. Press the Menu button and the PictBridge
menu will display.
2. Use the Up / Down buttons to select the
desired menu, and then press the Right button.
3. Use the Up / Down buttons to select the
desired sub menu value, and then press the
OK button.
Menu
PICTBRIDGE
Images
Size
Layout
Type
Quality
Date
Back
Function
Auto
PostCard
Card
4x6
L
2L
OK Set
Sub menu
Size
Set the size of the printing paper
Auto, PostCard, Card, 4X6, L,
2L, Letter, A4, A3
Layout
Set the number of pictures to be
printed on a sheet of paper
Auto, Full, 1, 2, 4, 8, 9,
16, Index
Type
Set the quality of the printing paper
Auto, Plain, Photo, FastPhoto
Quality
Set the quality of the picture to be
printed
Auto, Draft, Normal, Fine
Date
Set whether to print the date
Auto, Off, On
File Name
Set whether to print the file name
Auto, Off, On
Ä Some menu options are not supported on all printers.
If not supported, the menus are still displayed in the LCD, but are not selectable.
84 _PLAY
1. Use the Up / Down buttons to select the
[Reset] menu tab. And then press the Right
button.
2. Use the Up / Down buttons to select the
desired sub menu value, and then press the
OK button.
If [No] is selected : Settings will not be
reset.
If [Yes] is selected : All print and image settings will be reset.
PICTBRIDGE
Layout
Type
Quality
Date
File Name
Reset
Back
No
Yes
OK
Set
Ä Default print setting varies depending on the printer
manufacturer. For your printer’s default setting, refer to the user’s
guide that came with your printer.
Important notes
Be sure to observe the following precautions!
Do not leave this camera in places subject to dust, chemicals (like
naphthalene and mothballs), high temperature and high humidity.
Keep this camera with silica gel in a hermetically sealed box when not
planning to use the camera for a long period of time
Sand can be particularly troublesome to cameras.
- Do not let sand get inside the camera when using it on beaches,
coastal dunes, or other areas where there is lots of sand.
- Doing so may result in failure or may permanently render the camera
unusable.
Extremes in temperature may cause problems.
- If the camera is transferred from a cold to a warm and humid environment, condensation can form on the delicate electronic circuitry.
If this occurs, turn the camera off and wait for at least 1 hour until
all moisture is dispersed. Moisture built up can also occur on the
memory card. If this happens, turn off the camera and remove the
memory card. Wait until the moisture has dispersed.
Caution on Using the Lens
- If the lens is subjected to direct sunlight, it could result in the discoloration and deterioration of the image sensor.
- Take care not to get fingerprints or foreign substances on the surface
of the lens.
If the digital camera is not used for a long period, an electric discharge
can occur. It is a good idea to remove the battery and the memory card
if you do not intend using the camera for an extended period of time.
Handling the camera
- Never drop the camera or subject it to severe shocks or vibrations.
- Protect the large size LCD monitor from an impact. When this camera is not used, keep it in the camera case.
- Avoid obstructing the lens or the flash when you capture an image.
- This camera is not waterproof.
To avoid dangerous electrical shocks, never hold or operate the
camera with wet hands.
PLAY_ 85
04 PLAY
This unit contains precision electronic components. Do not use or store
this unit in the following locations.
- Areas exposed to severe changes in temperature and humidity.
- Areas exposed to dust and dirt.
- Areas exposed to direct sunlight or the inside of a vehicle in hot
weather.
- Environments where there is high magnetism or excessive vibration.
- Areas with high explosives or highly flammable materials.
- If you use this camera in wet places, such as beach or pool, do not
let water or sand get inside the camera. Doing so may result in failure
or may permanently damage the unit.
Important notes
Warning indicator
If the camera is exposed to an electronic interference, it will turn itself off
to protect the memory card.
There are several warnings that may appear on the LCD display.
Camera Maintenance
- Use a soft brush (available from photo stores) to gently clean the lens
and LCD assemblies. If this does not work, lens-cleaning paper with
lens cleaning fluid can be used.
Clean the camera body with a soft cloth. Do not allow this camera to
come into contact with solvent materials such as benzol, insecticide,
thinners etc. This may damage the body shell of the camera and also
affect its performance. Rough handling can damage the LCD monitor.
Take care to avoid damage and keep the camera in its protective carry
case at all times when not in use.
[ Card Error !]
Memory card error
" Turn off the camera power and turn it on again
" Insert the memory card again
" Insert and format the memory card (p.56)
[ Card Locked! ]
The memory card is locked
" SD/SDHC memory card : Slide the write protect switch to the top
of the memory card
Do not attempt to disassemble or modify the camera.
Under certain conditions, static electricity can cause the flash unit to fire.
This is not harmful to the camera and is not a malfunction.
When images are uploaded or downloaded, the data transfer may be
affected by static electricity. In this case, disconnect and re-connect the
USB cable before trying the transfer again.
Before an important event or going on a trip, you should check the
camera condition.
- Take a picture for testing the camera condition and prepare extra battery.
- Samsung cannot be held responsible for camera malfunctions.
86 _PLAY
[ No Card! ]
A memory card is not inserted
" Insert the memory card again
" Turn off the camera power and turn it on again
[ No Image! ]
There are no images stored on the memory
" Take images
" Insert a memory card that is holding some images
Warning indicator
Before contacting a service centre
[ File Error! ]
File error
" Delete the file.
Memory card error
" Contact a camera service centre.
Please check the following
[ Low Light! ]
When taking pictures in dark places
" Take pictures in Flash Photography mode.
04 PLAY
[ Low Battery! ]
There is low battery capacity
" Insert fresh batteries.
The camera doesn’t switch on
There is low battery capacity
" Insert fresh batteries. (p.12)
Battery is inserted incorrectly with the polarities reversed.
" Insert the battery according to the polarity marks (+, -).
The camera power ceases while in use
The battery is exhausted
" Insert fresh batteries.
The Camera is turned off automatically
" Turn on the camera power again.
Battery power quickly drains
The Camera is being used in low temperatures
" Keep the camera in warm conditions (i.e. inside a coat or jacket)
and only remove it in order to take images.
PLAY_ 87
Before contacting a service centre
Camera does not take images when pressing the Shutter button
There is insufficient memory capacity
" Delete unnecessary image files
The memory card has not been formatted
" Format the memory card (p.56)
The memory card is exhausted
" Insert a new memory card
The memory card is locked
" Refer to [Card Locked!] error message
The camera's power is off
" Turn the camera power on
The battery is exhausted
" Insert fresh batteries (p.12)
Battery is inserted incorrectly with the polarities reversed.
" Insert the battery according to the polarity marks (+, -)
The camera suddenly stops working while in use
The camera stopped due to a malfunction
" Remove /re-insert battery and switch the camera on
The images are unclear
A picture was taken of the subject without setting an appropriate
macro mode
" Select an appropriate macro mode to take a clear image.
Taking a picture beyond the flash range
" Take a picture within the flash range
The lens is smudged or dirty
" Clean the lens
88 _PLAY
The flash does not fire
Flash off mode has been selected
" Dis-engage flash off mode
The camera mode can't use the flash
" Refer to the FLASH instruction (p.26)
Incorrect date and time is displayed
The date and time have been set incorrectly or the camera has adopted the default settings
"Reset the date and time correctly
The camera buttons do not operate
Camera malfunction
" Remove/re-insert battery and switch the camera on
A card error has occurred while the memory card is in the camera.
Incorrect memory card format
" Re-format the memory card
The images don't play back
Incorrect file name (Violation of DCF format)
" Do not change the image file name
Colour of image is different to the original scene
White balance or effect setting is incorrect
" Select appropriate White balance and effect
Specifications
Images are too bright
Exposure is excessive
" Reset exposure compensation
Image Sensor
- Type : 1/2.5" CCD
- Effective Pixel : Approx. 8.2 Mega-pixel
- Total Pixel : Approx. 8.3 Mega-pixel
Lens
- Focal Length : SHD Lens f = 6.3 ~ 31.5mm
(35mm film equivalent : 38 ~ 190mm)
- F No. : F 2.8 ~ F 4.6
- Digital Zoom : ·Still Image mode :1.0X ~ 5.0X
·Play mode : 1.0X ~ 12.0X
(depends on image size)
LCD Monitor
- 2.5" color TFT LCD (230,000 dots)
Focusing
- Type : TTL auto focus, Multi-AF, Face Recognition AF
- Range
No image on external monitor
The external monitor has not been connected properly with
the camera
" Check the connection cables
There are incorrect files in the memory card
" Insert a memory card that has correct files
When using the PC’s explorer, the [Removable Disk] file does not show
Cable connection is incorrect
" Check the connection
The camera is off
" Turn the camera on
The operating system is not Windows 98SE, 2000, ME, XP, Vista /
Mac OS 10.0 - 10.4. Alternatively the PC does not support USB
" Install Windows 98SE, 2000, ME, XP, Vista / Mac OS 10.0 - 10.4 to
PC that supports USB
The camera driver is not installed
"Install a [USB Storage Driver]
Normal
Wide
Tele
80cm ~ Infinity
Macro
Super Macro
Auto Macro
5cm ~ 80cm
1cm ~ 5cm
5cm ~ Infinity
50cm ~ 80cm
-
50cm ~ Infinity
Shutter
- Speed 1~1/2,000 sec.
(Manual mode :15~1/2,000 sec.,
Night :15~1/2,000 sec., Fireworks :4 sec.)
Exposure
- Control : Program AE, Manual Exposure,
Face Recognition AE
- Metering : Multi, Spot, Center-weighted
- Compensation : ±2EV (1/3EV steps)
- ISO : Auto, 50, 100, 200, 400, 800, 1600
PLAY_ 89
04 PLAY
Before contacting a service centre
Specifications
Flash
- Modes : Auto, Auto & Red-eye reduction, Fill-in flash,
Slow sync, Flash off, Red-eye Fix
- Range : Wide : 0.4m ~ 3.0m,
Tele : 0.5m ~ 2.5m
- Recharging Time : Approx. 5 sec
Sharpness
- Soft+, Soft, Normal, Vivid, Vivid+
Color Effect
- Normal, B&W, Sepia, Blue, Red, Green, Negative,
Custom Color
White Balance
- Auto, Daylight, Cloudy, Fluorescent_H, Fluorescent_L,
Tungsten, Custom
- Movie Clip
·With Audio (recording time : memory capacity
dependent)
·Size : 640x480, 320x240
·Frame rate : 30 fps, 15 fps
·Optical Zoon up to 5.0X
·Movie Editing (Embedded): Pause during
recording, Still Image Capture
Storage
Voice Recording - Voice Recording (max. 10 hours)
- Voice Memo in Still Image (max. 10 sec.)
Date Imprinting
- Date, Date & Time, Off (user selectable)
Shooting
- Still Image
·Mode : Auto, Program, ASR, Manual, Scene, Portrait,
Night
·Scene : Children, Landscape, Close-up, Text, Sunset,
Dawn, Backlight, Fireworks, Beach & Snow,
Self Shot, Food, Cafe
·Shooting : Single, Continuous, AEB, Motion Capture,
Wise Shot
·Self-timer : 10 sec., 2 sec., Double, Motion Timer
90 _PLAY
- Media
·Internal memory : About 19MB flash memory
·External Memory (Optional)
: MMC card (Up to 1GB guaranteed)
SD card (Up to 2GB guaranteed)
SDHC card (Up to 4GB guaranteed)
- File Format
·Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1,
PictBridge 1.0
·Movie Clip : AVI (MJPEG)
·Audio : WAV
- Image Size
Ÿ
¬
­
✩
✨
✧
3264X
2448
3264X
2176
3264X
1824
2592X
1944
2048X
1536
1024X
768
Specifications
- Capacity (256 MB Size)
Dimensions (WxHxD)
- 100.3 X 63 X 23.4mm
(excluding protrusions)
¬
­
✩
✨
✧
57
68
84
93
172
558
Weight
- Approx. 154g (without batteries and card)
Fine
103
115
134
158
265
663
Operating Temperature
- 0 ~ 40°C
Normal
180
206
233
271
425
742
Operating Humidity
- 5 ~ 85%
Software
- Samsung Master, Adobe Reader
Ä These figures are measured under Samsung standard conditions and
may vary depending on shooting conditions and camera settings.
“E” Button
- Effect : Color, Image Adjust, Special Color,
Fun ( Highlight, Composite, Photo Frame)
- Editing : Resize, Rotate, Color, Special Color(Color
FIlter, Color Mask), Image Adjust ( Brightness,
Contrast, Saturation, Add Noise, Red Eye
Fix), Fun (Cartoon , Highlight, Composite,
Photo Frame, Sticker)
Image Play
- Type : Single image, Thumbnails, Slide show,
Movie Clip
Interface
- Digital output connector : USB 2.0
- Audio : Mono
- Video output : NTSC, PAL (user selectable)
- DC Adapter : 3.3V
Power Source
- Primary Battery : 2 X AA Alkaline
- Rechargeable battery (Optional) : SNB-2512 KIT
( 2xAA Ni-MH Battery & Charger )
Ä Included battery may vary depending on sale region.
04 PLAY
Ÿ
Super Fine
Specifications are subject to change without prior notice.
All trademarks are the property of their respective owners.
PLAY_ 91
Software Notes
Please ensure that you read the instruction manual carefully before use.
- The attached software is a camera driver and image editing software tool
for Windows.
- Under no circumstances should all or part of either the software or the
user manual be reproduced.
- Copyrights for software are licensed only for use with a camera.
- In the unlikely event of a manufacturing fault, we will repair or exchange
your camera.
We cannot, however, be held responsible in any way for damage caused
by inappropriate use.
- Using a Hand-made PC or a PC and OS that has not been guaranteed
by the manufacturer is not covered by the Samsung warranty.
- Before reading this manual, you should have a basic knowledge of computers and O/S (Operating Systems).
System Requirements
For Windows
PC with processor better than
Pentium II 450MHz
(Pentium 800MHz recommended)
Power Mac G3 or later
Windows 98SE / 2000 / ME / XP/Vista
Mac OS 10.0 ~ 10.4
Minimum 128MB RAM
(Over 512MB recommended)
200MB of available hard disk space
(Over 1GB recommend)
Minimum 64MB RAM
(Over 256MB recommended)
110MB of available hard-disk space
USB port
USB port
CD-ROM drive
CD-ROM drive
1024x768 pixels, 16bit color display
compatible monitor
(24bit color display recommended)
MicroSoft DirectX 9.0C
92 _SOFTWARE
For Macintosh
About the software
After inserting the CD-ROM provided with this camera into the CD-ROM
drive, the following window should automatically run.
Be sure to check the system requirements before installing the
driver.
You should allow 5 ~ 10 seconds for running the automatic
setup program according to the capability of your computer.
If the frame does not appear, run the [Windows Explorer] and
select [Installer.exe] in the CD-ROM Drive root directory.
Camera driver : This enables images to transfer between the camera
and PC.
This camera uses the USB Storage Driver as the camera driver. You
can use the camera as a USB card reader. After installing the driver and
connecting this camera to the PC, you can find [Removable Disk] in
[Windows Explorer] or [My computer]. A USB Storage Driver is provided
only for Windows. A USB Driver for MAC is not included with the Application CD. You can use the camera with Mac OS 10.0~10.4.
Samsung Master : This is the all-in-one multi media software solution.
You can download, view, edit and save your digital images and movie
clips with this software. This software is only compatible with Windows.
SOFTWARE_ 93
05 SOFTWARE
Before connecting the camera to the
PC, you should first install the camera
driver.
Setting up the application software
To use this camera with a PC, install the application software first.
After this has been done, the stored images in the camera can be moved
to the PC and can be edited by an image editing program.
You can visit the Samsung web-site through the internet.
http://www.samsungcamera.com : English
http://www.samsungcamera.co.kr : Korean
1. The auto run frame will display.
Click the [Install] menu in the Auto
run frame.
94 _SOFTWARE
2. Install the camera driver, DirectX, Samsung Master and Adobe Reader
by selecting a button shown on the monitor. If a latest version of
DirectX was installed on your computer, DirectX may not be installed.
Setting up the application software
3. After restarting the computer, connect the PC to the camera with the
USB cable.
05 SOFTWARE
4. Turn the camera power on.
The [Found New Hardware Wizard] will
open and the computer will recognise
the camera.
Ä If your OS is Windows XP/ Vista, an image viewer program will open.
If the download window of Samsung
Master opens after starting
Samsung Master, the camera driver was
set up successfully.
SOFTWARE_ 95
Setting up the application software
If you have installed the camera driver, the [Found New Hardware
Wizard] may not open.
On a Windows 98SE system, the Found New Hardware Wizard dialog
box opens and a window asking you to select a driver file may appear.
In this case, specify "USB Driver" in the CD supplied.
PDF documents of user manual are included in the Software CDROM supplied with this camera. Search the PDF files with Windows
explorer.
Before opening the PDF files, you must install the Adobe Reader
included in the Software CD-ROM.
To install the Adobe Reader 6.0.1 correctly, Internet Explorer 5.01 or
later has to be installed. Visit "www.microsoft.com" and upgrade the
Internet Explorer.
96 _SOFTWARE
Starting PC mode
If you connect the USB cable to a USB port on your PC and then turn on
the power, the camera will automatically switch to "computer connection
mode". In this mode, you can download stored images to your PC through
the USB cable.
Camera settings for connection
1. Turn on the camera
2. Connect the camera and computer with
the supplied USB cable.
3. Turn on the computer. The camera and
computer are connected.
4. External device selection menu will be
displayed on the LCD monitor.
5. Select the [Computer] by pressing the Up
/ Down button and press the OK button.
Select USB
Computer
Printer
OK
Confirm
Starting PC mode
Connecting the camera to a PC
Downloading stored images
You can download the still images stored on the camera to your PC's
hard disk and print them or use a photo editing software to edit them.
05 SOFTWARE
1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display,
select [My computer] and double click
[Removable Disk " DCIM" 100SSCAM].
The image files will then be displayed.
Ä If you selected [Printer] in Step 5, when you connect the camera to your
computer, the [Connecting Printer] message will display and the connection will not be established.
In this case, disconnect the USB cable, and then follow the procedure
from Step 2 and onward.
3. Select an image and press the right
mouse button.
Disconnecting the camera and PC
Refer to page 99 (Removing the removable disk).
SOFTWARE_ 97
Starting PC mode
4. A pop-up menu will open.
Click the [Cut] or [Copy] menu.
- [Cut]
: cuts a selected file.
- [Copy] : copies files.
- By using [Samsung Master], you can see the stored images in the
memory directly on the PC monitor and you can copy or move the
image files.
We recommend that you should copy the images to the PC to view
5. Click a folder where you want to paste the file.
6. Press the right mouse button and a pop-up
menu will open. Click [Paste].
7. An image file is transferred from the camera to your PC.
98 _SOFTWARE
them. Opening images directly from the removable disk may be
subject to unexpected disconnection.
When you upload a file that is not taken by this camera to the Removable Disk, the [File Error!] message will be displayed on the LCD
monitor in the PLAY mode, and nothing is displayed in THUMBNAIL
mode.
Removing the removable disk
Windows 2000/ME/XP/Vista
(The illustrations may differ from those shown depending on the
Windows O/S.)
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has
finished blinking and is constantly on.
5. A [Safe to Remove Hardware] window will
open. Click the [OK] button.
6. A [Unplug or Eject Hardware] window will
open. Click the [Close] button and the
removable disk will be removed safely.
05 SOFTWARE
Windows 98SE
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has
finished blinking and is constantly on.
2. Unplug the USB cable.
7. Unplug the USB cable.
2. Double-click the [Unplug or Eject Hardware] icon on the task bar.
[Double-click!]
3. The [Unplug or Eject Hardware]
window will open. Select the [USB Mass
Storage Device] and click the [Stop] button.
4. The [Stop a Hardware device] window
will open. Select the [USB Mass Storage
Device] and click the [OK] button.
SOFTWARE_ 99
Setting up the USB Driver for MAC
Removing the USB Driver for Windows 98SE
1. A USB Driver for MAC is not included with the software CD as MAC OS
supports the camera driver.
2. Check the MAC OS version during start-up.
This camera is compatible with MAC OS 10.0 ~ 10.4.
3. Connect the camera to the Macintosh and turn the camera power on.
4. A new icon will be displayed on the desktop after connecting the camera to the MAC.
To remove the USB driver, refer to the process shown below.
1. Connect the camera to your PC and turn them on.
2. Check whether the Removable Disk is on the [My Computer].
3. Remove the [Samsung Digital Camera] on the Device manager.
Using the USB Driver for MAC
1. Double click a new icon on the desktop and the folder in the memory
will be displayed.
2. Select an image file and copy or move it to MAC.
For Mac OS 10.0 or later : First complete uploading from computer
to camera and then remove the removable
disk with the Extract command.
4. Disconnect the USB cable.
5. Remove the [Samsung USB Driver] on the Add/Remove
Programs Properties.
6. Uninstallation is complete.
100 _SOFTWARE
Samsung Master
You can download, view, edit and save your images and movies with this
software. This software is only compatible with Windows.
To start the program, click [Start " Programs "Samsung "Samsung
Master "Samsung Master].
1. Connect the camera to your PC.
2. A window for downloading images
will be displayed after connecting the
camera to your PC.
- To download the captured images,
select the [Select All] button.
- Select desired folder in the window
and click the [Select All] button.
You can save captured images and
selected folder.
- If you click the [Cancel] button, downloading will be cancelled.
05 SOFTWARE
Downloading images
4. Select a destination and make a folder
to save downloaded images and folders.
- Folder names can be made in order of
date and images will be downloaded.
- Folder name will be made as you
want and images will be downloaded.
- After selecting a folder that was made
before, images will be downloaded.
5. Click [Next >] button.
6. A window will open as shown alongside.
The destination of the selected folder
will be displayed on the upper side of
the window.
Click the [Start] button to download the
images.
3. Click [Next >] button.
7. Downloaded images will be displayed.
SOFTWARE_ 101
Samsung Master
Image viewer : You can view the stored images.
Image edit : You can edit the still image.
[SN852297]
- Image viewer functions are listed below.
Ì Menu bar : You can select menus. File, Edit, View, Tools, Change
functions, Auto download, help, etc.
Í Image selection window : You can select the desired images in this
window.
/ Media type selection menu : You can select image viewer, image edit
and movie edit functions in this menu.
0 Preview window : You can preview an image or a movie clip and check
the multi media information.
1 Zoom bar : You can change preview size.
2 Folder display window : You can see the folder location of the selected
image.
3 Image display window : Images of the selected folder are displayed.
Ä Refer to the [Help] menu in Samsung Master for further information.
102 _SOFTWARE
- Image edit functions are listed below.
Ì Edit menu : You can select the following menus.
[Tools] : You can resize or crop the selected image. See the [Help]
menu.
[Adjust] : You can modify image quality. See the [Help] menu.
[Retouch] : You can change image or insert effects on the image.
See the [Help] menu.
Í Drawing tools : Tools for editing an image.
/ Image display window : A selected image displays in this window.
0 Preview window : You can preview the changed image.
Ä A still image edited with Samsung Master can’t be played back on the
camera.
Ä Refer to the [Help] menu in Samsung Master for further information.
Samsung Master
Movie edit : You can get the still image, movie clip, narration, music files
together in a movie clip.
Ä Some movie clips that were compressed with a codec that is not
compatible with the Samsung Master can’t play back in the Samsung
Master.
Ä Refer to the [Help] menu in Samsung Master for further information.
05 SOFTWARE
- Movie clip edit functions are listed below.
Ì Edit menu : You can select the following menus.
[Add Media] : You can add other media elements to a movie.
[Edit Clip]
: You can change the brightness, contrast, colour and
saturation.
[Effects]
: You can insert an effect.
[Set Text]
: You can insert texts.
[Narrate]
: You can insert a narration.
[Produce]
: You can save the edited multi media as a new file name.
You can select AVI, Windows media (wmv) and Windows
media (asf) file types.
Í Frame display window : You can insert multi media in this window.
SOFTWARE_ 103
FAQ
Please check the following if the USB connection malfunctions.
Case 1
USB cable is not connected or it is not the supplied USB
cable.
" Connect the supplied USB cable.
Case 2
The camera is not recognised by your PC.
Sometimes, the camera may appear under [Unknown Devices]
in Device Manager.
" Install the camera driver correctly.
Turn off the camera, remove the USB cable, plug in the USB
cable again, and then turn on the camera.
Case 3
There is an unexpected error during file transfer.
" Turn the camera power off and on again. Transfer the file
again.
Case 4
When using the USB hub.
" There may be a problem in connecting the camera to the PC
through the USB hub if the PC and the hub are not compatible. Wherever possible, connect the camera to the PC directly.
Case 5
Are other USB cables connected to the PC?
" The camera may malfunction when it is connected to the PC
at the same time as another USB cable. In this case, disconnect the other USB cable, and connect only one USB cable to
the camera.
104 _SOFTWARE
Case 6
When I open the Device Manager (by clicking Start (Settings)
Control Panel (Performance and Maintenance) System
(Hardware) Device Manager), there are Unknown Devices
or Other Devices entries with a yellow question mark(?) beside
them or devices with an exclamation mark(!) beside them.
" Right-click on the entry with the question (?) or exclamation (!)
mark and select "Remove". Restart the PC and connect the
camera again. For Windows 98SE PC, remove the camera
driver also, restart the PC, and then reinstall the camera driver.
Case 7
In some security programs (Norton Anti Virus, V3, etc.), the
computer may not recognise the camera as a removable disk.
" Stop the security programs and connect the camera to the
computer. Refer to the security program instructions about
how to temporarily disable the program.
Case 8
The camera is connected to the USB port located on the
front of the computer.
" When the camera is connected to the USB port located on the
front of the computer, the computer may not recognise the
camera. Connect the camera to the USB port located on the
back of the computer.
Correct Disposal of This Product
When the DirectX 9.0 or later is not installed
" Install the DirectX 9.0 or later
1) Insert the CD provided with the camera
2) Run the windows explorer and select the [CD-ROM drive:\ USB
Driver\DirectX 9.0] folder and click the DXSETUP.exe file.
The DirectX will be installed. Visit the following site for
downloading the DirectX.http://www.microsoft.com/directx
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking shown
on the product or its literature, indicates that it should not be
disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable re-use
of material resources. Household users should contact either the retailer
where they purchased this product, or their local government office, for
details of where and how they can take this item for environmentally safe
recycling. Business users should contact their supplier and check the
terms and conditions of the purchase contract. This product should not
be mixed with other commercial wastes for disposal.
If a PC (Windows 98SE) stops responding while the camera and PC are
connected repeatedly
" If a PC (Windows 98SE) is turned on for a long time and the camera
is connected repeatedly, the PC may not recognise the camera. In
this case, re-start the PC.
If a PC connected with the camera stops responding while Windows
is starting.
" In this case, disconnect the PC and the camera and
Windows will start. If the problem happens continuously, set the
Legacy USB Support to disable and re-start the PC. The Legacy
USB Support is in the BIOS setup menu. (The BIOS setup menu differs from the PC manufacturers and some BIOS menus don’t have
Legacy USB Support) If you can’t change the menu by yourself,
contact to the PC
manufacturer or BIOS manufacturer.
If the movie clip can’t be deleted, or the removable disk can’t be extracted or an error message displays during the file transfer.
" If you install only the Samsung Master, the problems
mentioned above occasionally happen.
- Close the Samsung Master program by clicking the
Samsung Master icon on the Taskbar.
- Install all the application programs included in the software CD.
Samsung Techwin cares for the environment at all product
manufacturing stages to preserve the environment, and is
taking a number of steps to provide customers with more
environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly
products, and indicates that the product satisfies the EU
RoHS Directive.
SOFTWARE_ 105
05 SOFTWARE
FAQ
FCC notice
Declaration of Conformity
NOTE :
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and receiver.
- Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION :
Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the
equipment.
106 _SOFTWARE
Trade Name
: SAMSUNG TECHWIN
Model No.
: SAMSUNG S85/D85
Responsible Party
: Samsung Opto-Electronics America, INC.
Address
: 40 Seaview Dr. Secaucus,NJ 07094
Telephone No.
: 201-902-0347
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause
undesired operation.
MEMO
107
MEMO
108
Download PDF

advertising