Samsung | KENOX S850 | Samsung KENOX S850 User Manual

User Manual
Thank you for buying a Samsung camera.
This manual will guide you through using the camera, including
capturing images, downloading images and using the application software.
Please read this manual carefully before using your new camera.
ENGLISH
Instructions
Getting to know your camera
■ Use this camera in the following order.
Set up the camera driver
Take a picture
Insert the USB cable
Before connecting the camera to a PC, via
the USB cable, you will need to set up the
camera driver. Install the camera driver
that is contained in Application software
CD-ROM. (p.74)
Take a picture. (p.14)
Insert the supplied USB cable into the
PC’s USB port and the camera’s USB
connection terminal. (p.77)
Check the camera’s power
Check the camera’s power. If the power is
turned off, press the camera button to turn
it on.
Check [Removable Disk]
Open Window’s EXPLORER and search
for [Removable Disk]. (p.79)
Thank you for buying a Samsung Digital Camera.
● Prior to using this camera, please read the user manual thoroughly.
● When you require After Sales service, please bring the camera and the cause of
the camera malfunction (such as battery, Memory card etc.) to the A/S centre.
● Please check that the camera is operating properly prior to when you intend to
use it (e.g. for a trip or an important event) to avoid disappointment. Samsung
camera takes no responsibility for any loss or damages that may result from
camera malfunction.
● Keep this manual in a safe place.
● The contents and illustrations of this manual are subject to change without prior
notice for upgrading the camera functions.
Microsoft, Windows and Windows logo are registered trademarks of Microsoft
Corporation incorporated in the United States and/or other countries.
All brand and product names appearing in this manual are registered trademarks
of their respective companies.
《1》
Danger
DANGER indicates an imminently hazardous situation which, if not avoided, will
result in death or serious injury.
■ Do not attempt to modify this camera in any way. To do so may result in fire,
injury, electric shock or severe damage to you or your camera. Internal
inspection, maintenance and repairs should only be carried out by your dealer or
Samsung Camera Service centre.
■ Please do not use this product in close proximity to flammable or explosive
gases, as this could increase the risk of explosion.
■ Should any form of liquid or a foreign object enter the camera, do not use it.
Switch off the camera, and then disconnect the power source. You must contact
your dealer or Samsung Camera Service centre. Do not continue to use the
camera as this may cause a fire or electric shock.
■ Do not insert or drop metallic or inflammable foreign objects into the camera
through access points e.g. the memory card slot and battery chamber. This may
cause a fire or electric shock.
■ Do not operate this camera with wet hands. This could pose a risk of electric
shock.
《2》
Warning
WARNING indicates a potentially hazardous situation which, if not avoided, could
result in death or serious injury.
■ Do not use the flash in close proximity to people or animals. Positioning the flash
too close to your subject’s eyes may cause eyesight damage.
■ For safety reasons keep this product and accessories out of reach of children or
animals to prevent accidents e.g.:
•Swallowing battery or small camera accessories. If an accident should occur,
please consult a doctor immediately.
•There is the possibility of injury from the camera’s moving parts.
■ Battery and camera may become hot during prolonged use and it may result in
camera malfunction. Should this be the case, allow the camera to sit idle for a
few minutes to allow it time to cool.
■ Do not leave this camera in places subject to extremely high temperatures, such
as a sealed vehicle, direct sunlight or other places of extreme variances in
temperature. Exposure to extreme temperatures may adversely affect the
camera’s internal components and could cause a fire.
■ When in use, do not cover the camera or Charger. This may cause heat to build
up and distort the camera body or cause a fire. Always use the camera and its
accessories in a well-ventilated area.
Caution
CAUTION indicates a potentially hazardous situation which, if not avoided, may
result in a minor or moderate injury.
■ Leaking, overheating, or damaged battery could result in fire or injury.
•Use battery with the correct specification for the camera.
•Do not short circuit, heat or dispose of battery in fire.
•Do not insert the battery with the polarities reversed.
■ Remove the battery when not planning to use the camera for a long period of
time. Otherwise the battery may leak corrosive electrolyte and permanently
damage the camera’s components.
■ Do not fire the flash while it is in contact with hands or objects. Do not touch the
flash after using it continuously. It may cause burns.
■ Do not move the camera while it is switched on, if you are using the AC Charger.
After use, always switch off the camera before unplugging the cable from the
wall socket. Then make sure that any connector cords or cables to other devices
are disconnected before moving the camera. Failure to do so may damage the
cords or cables and cause a fire or electric shock.
■ Take care not to touch the lens or lens cover to avoid taking an unclear image
and possibly causing camera malfunction.
■ Avoid obstructing the lens or the flash when you capture an image.
■ Before inserting any cables or AC adapter, check the directions and do not insert
by force. It may cause breakage of cable or camera.
■ Credit cards may be demagnetized if left near case. Avoid leaving magnetic strip
cards near the case.
Contents
READY
●System chart ………………………5
●Identification of features ……………6
■Front & Top …………………………6
■Back & Bottom ……………………7
■Bottom / 5-function button …………8
■Self-timer lamp ……………………8
■Camera Status Lamp………………8
■Mode icon …………………………9
●Connecting to a Power Source ……9
●Inserting the memory card ………10
●Instructions on how to use the
memory card ………………………11
RECORDING
●LCD monitor indicator ……………13
●Starting the recording mode………14
■How to use the AUTO mode ……14
■How to use the PROGRAM
mode ………………………………14
■How to use the APERTURE
PRIORITY mode …………………14
■How to use the SHUTTER PRIORITY
mode ………………………………15
■How to use the MANUAL mode …15
■How to use the ASR (Advanced
Shake Reduction) mode …………15
■Wise Shot …………………………16
■How to use the SCENE mode …16
■How to use the MOVIE CLIP
mode ………………………………17
■Recording the movie clip without
voice ………………………………17
■Pausing while recording a movie clip
(Successive Recording) …………17
■Using Successive Recording ……17
■How to use the VOICE
RECORDING mode………………18
●Things to Watch Out for When
Taking Pictures ………………………18
●Using the camera buttons to set the
camera ……………………………19
■POWER button……………………19
■Shutter button ……………………19
■ZOOM W / T button ………………20
■Voice recording / Voice memo UP
button………………………………21
■Macro / Down button ……………22
■Focus lock…………………………23
■Flash / Left button…………………24
■Self-timer / Right button …………26
■MENU / OK button ………………26
《3》
Contents
■E (Effect) button …………………27
■Special Effect : Colour ……………27
■Special Effect :
Preset focus frames ………………28
■Special Effect :
Composite shooting ………………29
■Special Effect : Photo Frame ……30
■Movie Clip frame stabiliser ………31
■+/ - button …………………………31
●Using the LCD monitor to set the
camera settings ……………………34
■How to use the menu ……………35
■Size ………………………………36
■Quality/ Frame rate ………………36
■Metering …………………………37
■Auto Focus type …………………37
■Continuous shot …………………38
■Sharpness…………………………39
■OSD (On Screen Display)
information ………………………39
PLAY
●Starting play mode ………………40
■Playing back a still image ………40
■Playing back a movie clip ………40
■How to capture the movie clip……41
《4》
■On camera movie trimming………41
■Playing back a recorded voice …42
●LCD monitor Indicator ……………42
●Using the camera buttons to set the
camera ……………………………43
■Thumbnail / Enlargement button…43
■Voice memo/ Up button …………44
■Play & Pause / Down button ……45
■E (Effect) button …………………45
■Delete button ……………………46
■Printer button ……………………47
■Left/ Right/ Menu/ OK button ……47
●Setting up the play back function
using the LCD monitor ……………48
■Starting the slide show……………50
■On Screen Display information …51
■Rotating an image ………………51
■Resize ……………………………52
■Protecting images ………………53
■Deleting images …………………53
■Copy To Card ……………………54
■DPOF ……………………………55
■DPOF : Standard …………………55
■DPOF : Index ……………………56
■DPOF : Print size …………………56
■PictBridge …………………………57
■PictBridge : Picture Selection ……57
■PictBridge : Print Setting …………58
■PictBridge : Printing ………………59
■PictBridge : DPOF Printing ………60
■PictBridge : Reset…………………60
SETUP
●Setup menu ………………………61
■File name …………………………62
■Auto power off ……………………62
■Language …………………………62
■Formatting a memory ……………63
■Setting up the Date/ Time/
Date type …………………………63
■World Time ………………………64
■Imprinting the recording date ……64
■Auto Focus lamp …………………64
■Sound ……………………………64
■Connecting an External Device
(USB)………………………………65
■LCD brightness……………………65
■Selecting Video out type …………65
■Quick view…………………………66
■Initialisation ………………………66
●Setting up the Mycam menu ……67
■Start up image ……………………67
■Start up sound ……………………67
■Shutter sound ……………………67
●Important notes ……………………68
●Warning indicator …………………69
●Before contacting a service
centre ………………………………70
●Specifications………………………72
SOFTWARE
●Software Notes ……………………74
●System Requirements ……………74
●About the software ………………74
●Setting up the application
software ……………………………75
●Starting PC mode …………………77
●Removing the removable disk ……79
●Setting up the USB Driver
for MAC ……………………………80
●Using the USB Driver for MAC …80
●Removing the USB Driver for
Windows 98SE ……………………80
●Digimax Master ……………………81
●FAQ ………………………………83
System chart
Please check that you have the correct contents before using this product. The contents can vary depending on the sales region. To buy the optional equipment, contact your
nearest Samsung dealer or Samsung service centre.
< Included items >
Camera case
DPOF compatible
printer (see p.55)
User manual,
Product warranty
Camera strap
Software CD
(see p.74)
Computer
(see p.77)
PictBridge compatible printer
(see p.57)
SD memory card/ MMC
(see p.10)
USB cable
Rechargeable battery
(SNB-2512)
AV cable
AA Alkaline
Batteries
or
External monitor
(see p. 65)
AC cord
Charger(SBC-N1)
Charger(SBC-N2)
《5》
Identification of features
Front & Top
Mode dial
Power button
Shutter button
Speaker
Flash
Self-timer lamp /
Auto focus lamp
USB / AV connection terminal
Lens / Lens cover
DC input connection port
Microphone
《6》
Identification of features
Back & Bottom
Camera status lamp
Zoom T button (Digital zoom)
Zoom W button (Thumbnail)
LCD monitor
E (Effects) button
Strap eyelet
+/- button, Delete button
5 function button
Tripod socket
Play mode /
Printer button
《7》
Identification of features
■ Self-timer lamp
Bottom / 5-function button
Icon
Status
Battery chamber cover
Blinking
Blinking
Memory card slot
Blinking
Battery chamber
Description
For the first 7 seconds, the lamp blinks at 1 second
intervals.
For the final 3 seconds, the lamp blinks quickly at 0.25second intervals.
For the 2 seconds, the lamp blinks quickly at 0.25-second
intervals before taking a picture
A picture will be taken after about 10 seconds and 2
seconds later a second picture will be taken.
■Camera Status Lamp
Status
Description
The lamp turns on and off when the camera is ready to
take a picture
The lamp blinks while saving the image data and turns
After taking a picture
off when the camera is ready to take a picture
While voice memo recording The lamp blinks
While voice recording
The lamp blinks
Transmitting Data with a PC The lamp turns on (LCD monitor turns off)
Power on
Voice memo / Voice Recording / Up button
Menu / OK button
Flash /
Left button
Self-timer /
Right button
When the USB cable is
inserted to a printer
The lamp is off
When the printer is printing The lamp blinks
The lamp turns on (The camera focus on the subject)
When the AF activates
The lamp blinks (The camera doesn't focus on the subject)
Macro / Down button
Play & Pause button
《8》
Identification of features
Connecting to a Power Source
■ Mode icon: Refer to page 15~18 for more information about the camera mode
setting.
MODE
AUTO
PROGRAM
A
S
M
ASR
MOVIE
VOICE RECORDING
PLAY
-
Icon
MODE
Icon
MODE
SCENE
PORTRAIT CHILDREN LANDSCAPE
TEXT
● We recommend using batteries for a digital camera (Within a year from the date
of manufacture). The batteries are listed below.
- Non rechargeable batteries
: 2 X AA Alkaline (High Capacity)
- Rechargeable batteries (Optional) : SNB-2512 (Ni-MH)
Model
-
NIGHT
Using the batteries
CLOSE UP
Ni-MH
Capacity
2500mAh
Voltage
1.2V x 2
Icon
MODE
Icon
SUNSET
DAWN
BACKLIGHT FIREWORKS BEACH & SNOW
-
SNB-2512
Type
Charging time
Approximately 300 Minutes(Use for SBC-N2)
Approximately 240 Minutes(Use for SBC-N1)
※ Included battery may vary depending on sales region.
《9》
Connecting to a Power Source
INFORMATION
Important information about battery usage
● When the camera is not used, turn off the camera power.
● Please remove the battery if the camera will not be used for long periods.
Battery can lose power over time and are prone to leaking if kept inside the
camera.
● Low temperatures (below 0˚C) can affect the performance of the battery
and you may experience reduced battery life.
● Batteries will usually recover at normal temperatures.
● During extended use of the camera, the camera body may become warm.
This is perfectly normal.
■ Insert the battery as shown
- If the camera does not turn on after you
have inserted battery, please check
whether the battery is inserted with the
correct polarity (+ / -).
- When the battery chamber cover is
opened, do not press the battery
chamber cover by force. This may cause
damage to the battery chamber cover.
《10》
■ There are 4 indicators for battery condition that are displayed on the LCD
monitor.
Battery
indicator
Battery
status
The battery is
fully charged
Low battery
Low battery
Low battery
capacity
capacity (Prepare
capacity
(Prepare to
to recharge
(Prepare to
or use spare recharge or use recharge or use
battery)
spare battery) spare battery)
Inserting the memory card
■ Insert the memory card as shown.
- Turn off the camera’s power before
inserting the memory card.
- Have the front of the memory card facing
toward the front of the camera (lens) and
the card pins toward the back of the
camera (LCD monitor).
- Do not insert the memory card the wrong
way round. Doing so may damage the
memory card slot.
Instructions on how to use the memory card
● Be sure to format the memory card (see p.63) if you are using a newly
purchased memory for the first time, if it contains data that the camera cannot
recognise, or if it contains images captured with a different camera.
● Turn off the camera power whenever the memory card is being inserted or
removed.
● Repeated use of the memory card will eventually reduce the memory card’s
performance. Should this be the case, you will need to purchase a new memory
card. Wear and tear on the memory card is not covered by the Samsung
warranty.
● The memory card is an electronic precision device.
Do not bend, drop or subject the memory card to any heavy impact.
● Do not store the memory card in an environment with strong electronic or
magnetic fields, e.g. near loud speakers or TV receivers.
● Please do not use or store in an environment where there are extremes in
temperature.
● Do not allow the memory card to become dirty or to come into contact with any
liquid. Should this happen, clean the memory card with a soft cloth.
● Please keep the memory card in its case when not in use.
● During and after periods of extended use, you may notice that the memory card
is warm. This is perfectly normal.
● Do not use a memory card that is used in another digital camera.
To use the memory card in this camera, format the memory card using this
camera.
● Do not use a memory card formatted by another digital camera or memory card
reader.
● If the memory card is subjected to any of the following, the recorded data may
become corrupted :
- When the memory card is used incorrectly.
- If the power is switched off or the memory card is removed while recording,
deleting (formatting) or reading.
● Samsung cannot be held responsible for lost data.
● It is advisable to copy important data onto other media as back-up e.g. floppy
disks, hard disks, CD etc.
● If there is insufficient memory available
: A [Memory Full!] message will appear and the camera will not operate. To
optimise the amount of memory in the camera, replace the memory card or
delete unnecessary images stored on the memory card.
《11》
Instructions on how to use the memory card
INFORMATION
● Don't remove the memory card when the camera status lamp is blinking as
this may cause damage to data in the memory card.
■ When using a 256MB MMC (Multi Media Card), the specified shooting capacity
will be as follows. These figures are approximate as image capacities can be
affected by variables such as subject matter and memory card type.
Recorded image size
■ The camera can use SD/SDHC Memory Cards and MMC (Multi Media Cards).
Please consult the enclosed manual for using the MMC Cards.
Super Fine
Fine
Normal
8M
57
103
180
5M
93
158
271
3M
172
265
425
1M
558
663
742
Print
7M(P)
68
115
206
Wide
6M(W)
Still image
Card pins
Write protect
switch
Label
[ SD (Secure Digital) memory card ]
* Movie clip
The SD/SDHC memory card has a write protect switch that prevents image files
from being deleted or formatted. By sliding the switch to the bottom of the
SD/SDHC memory card, the data will be protected. By sliding the switch to the top
of the SD/SDHC memory card, the data protection will be cancelled.
Slide the switch to the top of the SD/SDHC memory card before taking a picture.
《12》
84
134
233
30FPS
20FPS
15FPS
800
-
About 10' 56"
About 11' 53"
720
-
About 11' 44"
About 15' 12"
640
About 11' 10"
About 15' 48"
About 18' 20"
320
About 39' 03"
About 48' 08"
About 67' 52"
Recorded image size
※ The recording times can be changed by the zoom operation.
The zoom button doesn’t use during the movie recording.
LCD monitor indicator
■ The LCD monitor displays information about the shooting functions and
selections.
No.
Description
4
Continuous shot
Icons
p.38
5
Flash / Without Sound
p.24~25
/ p.17
⑳
6
Self-timer
p.26
③
⑲
7
Macro
p.22~23
④
⑱
8
Metering
p.37
9
Card inserted indicator
-
①
②
⑤
⑰
⑥
⑯
Page
10
Auto focus frame
p.37
11
Camera shake warning
p.18
⑦
⑮
12
Date / Time
⑧
⑭
13
Exposure compensation
p.34
⑨
⑬
14
White Balance
p.33
15
ISO
16
RGB
⑩
⑪
⑫
Description
1
Recording mode
2
Battery
3
Aperture Value / Shutter Speed
Icons
F2.8, 1/30
p.63
p.32
RGB
p.32
17
Sharpness
p.39
18
Image quality / Frame rate
p.36
Page
19
Image size
p.36
p.14~18
20
[Image & Full Status]
No.
2007/01/01 01:00 PM
Number of available shots remaining
7
p.12
Remaining time (Movie clip/ Voice recording)
00:01:30/ 01:00:00
p.12
p.10
21
Voice memo
p.21
p.14~15
22
Optical/ Digital Zoom bar/ Digital Zoom rate
p.20
《13》
Starting the recording mode
■ How to use the AUTO mode (
)
Please select this mode for quick and easy picture taking with minimal user
interaction.
1. Insert the batteries (p.10). Insert the batteries
taking note of the polarity (+ / -).
2. Insert the memory card (p.10). As this camera has
a 20MB internal memory, you do not need to insert
the memory card. If the memory card is not
inserted, an image will be stored in the internal
memory. If the memory card is inserted, an image
will be stored on the memory card.
3. Close the battery chamber cover.
4. Press the power button to turn on the camera.
(If the date/ time that is displayed on the LCD
[ AUTO mode ]
monitor is incorrect, reset the date / time before
taking a picture.)
5. Select the AUTO mode by rotating the mode dial.
6. Point the camera towards the subject and compose the image by using the
LCD monitor.
7. Press the shutter button to capture an image.
■ How to use the PROGRAM mode (
)
Selecting the automatic mode will configure the
camera with optimal settings. You can still manually
configure all functions except the aperture value and
shutter speed.
1. Select the PROGRAM mode by rotating the mode
dial.
2. Press the menu button to configure advanced
functions such as image size (p.36), quality (p.36),
metering (p.37), auto focus type (p.37), continuous
shooting (p.38), sharpness(p.39) and OSD
information(p.39).
■ How to use the APERTURE PRIORITY mode (
[ PROGRAM mode ]
)
1. Select the APERTURE PRIORITY Mode by
rotating the mode dial.
2. Set the aperture value by using the +/-, up/down
button.
3. Press the + / - button twice and take an image.
INFORMATION
● If the auto focus frame turns to red when you press the shutter button down
half way, it means that the camera cannot focus on the subject. Should this
be the case, the camera is unable to capture an image clearly.
《14》
[APERTURE PRIORITY mode]
* Smaller Aperture values make the object sharp but blur the background.
Larger Aperture values make both the object and background sharp.
Starting the recording mode
■ How to use the SHUTTER PRIORITY mode (
)
1. Select the SHUTTER PRIORITY Mode by
rotating the mode dial.
2. Set the shutter speed by using the +/-, Left/Right
button.
3. Press the + / - button twice and take an image.
* High Shutter speeds can capture a moving object in a
still image as if the object is not moving. Low Shutter
speeds can capture a moving object with an ‘active’
effect.
■ How to use the ASR (Advanced Shake Reduction) mode (
Advanced Shake Reduction (ASR) mode.
This mode will reduce the effect of camera shake and
help you get a well-exposed image in dim conditions.
Press the ASR button.
[SHUTTER PRIORITY mode]
■ How to use the MANUAL mode (
)
You can manually configure all functions with the
aperture value and shutter speed.
1. Select the MANUAL mode by rotating the mode
dial.
2. Press the + / - button and menu for the shutter
speed and aperture value will display.
Up / Down button
: changes aperture value
Left / Right button
: changes shutter speed.
3. Press the + / - button twice and take an image.
)
● Things to watch out for using the ASR mode
1. The digital zoom will not operate in the ASR
mode.
2. If the lighting conditions are brighter than
fluorescent lighting condition, the ASR doesn’t
activate.
3. If the lighting condition is darker than in
fluorescent lighting condition, camera shake
[ASR mode]
warning indicator (
) will display. For best
results only take pictures in situations where
the camera shake warning indicator (
) is not displayed.
4. If the subject is moving the final image captured may be blurred.
5. Avoid moving the camera while the [Capturing!] message is displayed to
achieve a better result.
6. As the ASR uses the camera’s digital processor, images taken using the ASR
may take a little longer for the camera to process.
[MANUAL mode]
《15》
Starting the recording mode
■ Wise Shot
2 images are taken at a time. One is taken in the Fill-In Flash mode and the other
is taken in the ASR mode. You can select and save only one of the images.
● How to use the Wise Shot
1. Select the ASR mode by rotating the mode dial.
■ How to use the SCENE mode (
)
Use the menu to easily configure optimal settings
for a variety of shooting situations.
1. Select the SCENE mode by rotating the mode
dial.
2. Press the menu button and select a desired
scene menu.
2. Press the Menu button and the Wise Shot
function is activated.
3. Press the Shutter button to capture images.
4. Captured images are displaying.
- To select image, press the Left/Right button.
Image with the ASR
mode
[SCENE mode]
Image with Flash
Enlarged image
Enlarged image
Save: OK
Move.:
5. Press the OK / Shutter button and the selected image will be saved.
INFORMATION
● In the Wise shot mode, the shutter speed value shown on the LCD monitor may be
different with the real shutter speed.
● Wise shot can be taken at
,
,
,
size.
《16》
※The scene modes are listed below.
[Nightscene] (
) : Use this for shooting still images at night or in other
dark conditions.
[Portrait]
(
) : To take a picture of a person.
[Children]
(
) : To take a picture of fast moving objects, for
example, children.
[Landscape] (
) : To take pictures of distant scenery.
[Text]
(
) : Use this mode to shoot a document.
[Close up]
(
) : Close-up shooting for small objects such as plants
and insects.
[Sunset]
(
) : For taking pictures of sunsets.
[Dawn]
(
) : Daybreak scenes..
[Backlight]
(
) : Portrait without shadows caused by backlight.
[FIirework]
(
) : Firework scenes.
[Beach&Snow] (
) : For ocean, lake, beach and snowscape scenes.
Starting the recording mode
■ How to use the MOVIE CLIP mode (
)
A movie clip can be recorded for as long as the
available recording time of the memory capacity
allows.
■ Pausing while recording a movie clip (Successive Recording)
This camera allows you to temporarily stop during unwanted scenes, while
recording a movie clip. Using this function, you can record your favourite scenes
into a movie clip without having to create multiple movie clips.
1. Select the MOVIE CLIP mode by rotating the
mode dial.
2. The MOVIE CLIP mode icon and available
recording time will display on the LCD monitor.
3. Point the camera towards the subject and
compose the image by using the LCD monitor.
Press the shutter button and movie clips are
[ MOVIE CLIP mode ]
recorded for as long as the available recording time.
Movie clips will still be recorded if the shutter button is released.
If you wish to stop recording, press the shutter button again.
* Image size and type are listed below.
- Image size : 800X592, 720X480, 640x480, 320x240 (Selectable)
- File type
: *.avi (MPEG-4)
■ Recording the movie clip without voice
You can record the movie clip without voice.
1. Press the Up button and the (
) icon will
display on the LCD monitor.
2. Press the shutter button and movie clip is
recorded for as long as the available recording
time without voice.
3. To stop the recording, press the shutter button
again.
● Using Successive Recording
1. Press the shutter button and movie clips are
recorded for as long as the available recording
time. Movie clips will still be recorded if the shutter
button is released.
2. Press the Pause button (
) to pause
Stop:Shutter Pause: /
recording. Press the Pause button (
) again to
[Successive recording of a movie clip]
resume the recording.
3. If you wish to stop recording, press the shutter
button again.
INFORMATION
● 30 FPS cannot be used in 800X592, 720X480 size.
[ MOVIE CLIP mode ]
《17》
Starting the recording mode
■ How to use the VOICE RECORDING mode (
)
A voice can be recorded for as long as the available
recording time (max:1hour) allows.
1. In any mode with the exception of Movie clip mode,
select the VOICE RECORDING mode by pressing
the Voice recording button twice.
2. Press the shutter button to record a voice.
- Press the shutter button once and voice is
recorded for as long as the available recording
time (max:1hour) allows. The recording time will
be displayed on the LCD monitor. Voice will still
REC:Shutter
EXIT:
be recorded if the shutter button is released.
- If you wish to stop recording, press the shutter
[ VOICE RECORDING mode ]
button again.
- File type : *.wav
* A distance of 40cm between you and the camera (microphone) is the best
distance to record sound.
《18》
Things to Watch Out for When Taking Pictures
■ Pressing the shutter button down half way.
Lightly press the shutter button to confirm focus and flash battery charge.
Press the shutter button all way down to take the picture.
[ Lightly press the shutter button ]
[ Press the shutter button ]
■ The available recording time may vary depending on shooting conditions and
camera settings.
■ When the Flash Off or Slow synchro mode is selected in a low lighting condition,
the camera shake warning indicator (
) may appear on the LCD monitor.
In this case, use a tripod, support the camera on a solid surface or change to
flash shot mode.
■ Shooting against the light :
Please do not take pictures to the sunlight direction. Taking a picture against the
sun may make the picture dark. To take a picture against the sun, please use the
[Backlight] in the scene shooting mode (see page 16), fill-in flash (see page 25),
spot metering (see page 37), or exposure compensation (see page 34).
■ Avoid obstructing the lens or the flash when you capture an image.
■ Compose the image by using the LCD monitor.
Things to Watch Out for When Taking Pictures
■ Under certain conditions the auto focus system may not perform as expected.
- When photographing a subject that has little contrast.
- If the subject is highly reflective or shiny.
- If the subject is moving at high speed.
- When there is strong reflected light, or when the background is very bright.
- When the subject matter has only horizontal lines or the subject is very narrow
(such as a stick or flagpole).
- When the surroundings are dark.
Using the camera buttons to set the camera
■ The recording mode function can be set up by using the camera buttons.
POWER button
● Used for turning the camera’s power on / off.
● If there is no operation during the specified time,
the camera's power will be turned off automatically
to save battery life.
Refer to page 62 for more information about the
auto power off function.
Shutter button
● Used for taking an image or recording voice in the
RECORDING mode.
● In MOVIE CLIP mode
Pressing the shutter button down fully starts the
process for recording a movie clip. Press the
shutter button once and the movie clip is recorded
for as long as the available recording time in the
memory allows. If you wish to stop recording, press the shutter button again.
● In STILL IMAGE mode
Pressing the shutter button down halfway activates the autofocus and checks
the condition of the flash. Pressing the shutter button down fully takes and stores
the image. If you select voice memo recording, the recording will start after the
camera has finished storing the image data.
《19》
ZOOM W / T button
● If the menu is not displayed, this button works as
the OPTICAL ZOOM or DIGITAL ZOOM button.
● WIDE Zoom
Optical zoom WIDE
● This camera has a 5X optical zoom and a 5X digital zoom function.
Using both will offer a total zoom ratio of 25X.
● TELE Zoom
Optical zoom TELE
Digital zoom TELE
: Pressing the ZOOM T button. This will zoom into the
subject i.e. the subject will appear nearer.
: When the maximum (5X) optical zoom is selected,
pressing the ZOOM T button activates the digital zoom
software. Releasing ZOOM T button stops the digital
zooming at the required setting. Once the maximum
digital zoom (5X) is achieved, pressing the ZOOM T
button will have no effect.
Pressing
the ZOOM
T button
Pressing
the ZOOM
T button
[ WIDE zoom ]
[ TELE zoom ]
Pressing
the ZOOM
W button
Pressing
the ZOOM
W button
[ Optical zoom 2X ]
[ TELE zoom ]
Digital zoom WIDE
Optical zoom
Digital zoom
[ WIDE zoom ]
: When the digital zoom is in operation, pressing the
ZOOM W button will reduce the digital zooming in
steps. Releasing ZOOM W button stops digital
zooming. Pressing the ZOOM W button will reduce the
digital zoom and then it will continue to reduce the
optical zoom until the minimum setting is reached.
Pressing
the ZOOM
W button
Pressing
the ZOOM
W button
[ Digital zoom 5X ]
[ Digital zoom 5X ]
《20》
: Pressing the ZOOM W button. This will zoom out from
the subject i.e. the subject will appear farther away.
Pressing the ZOOM W button continuously will set the
camera to its minimum zoom setting i.e. the subject
appears at its farthest from the camera.
[ TELE zoom ]
[ WIDE zoom ]
ZOOM W / T button
INFORMATION
● Images taken using the digital zoom may take a little longer for the camera
to process. Allow time for this to take place.
● The digital zoom cannot be used in movie clip shots.
● You may notice a decrease in image quality when using the digital zoom.
● To view a clearer digital zoom image, press the shutter button halfway at the
maximum (5X) optical zoom position and press the zoom T button again.
● The digital zoom can't be activated in the Nightscene, Children, Text, Close
up, Firework, ASR mode.
● Take care not to touch the lens to avoid taking an unclear image and
possibly causing camera malfunction. If the image is dim, turn the camera
power off and on again to modify the lens position.
● Take care not to press the lens as this may cause a camera malfunction.
● When the camera is turned on, take care not to touch the camera's moving
lens parts as this may cause the resulting image to be dim and unclear.
Voice recording(
) / Voice memo(
) / UP button
■ While the menu is showing, press the UP button to move up the sub menu.
When the menu is not displayed on the LCD monitor, the UP button operates as
the voice recording or voice memo (
) button. You can add your voice-over to
a stored still image. Refer to page 18 for more information about the voice
recording.
● Recording a voice memo
1. Rotate the MODE DIAL to select a RECORDING mode with the exception of
MOVIE CLIP mode.
2. Press the VOICE MEMO (
) button. If the voice memo indicator is
displayed on the LCD monitor, the setting is completed.
Stop:Shutter
[Preparing for Voice Memo]
[Recording Voice Memo]
3. Press the shutter button and take a picture. The picture is stored on the
memory card.
4. Voice memo will be recorded for ten seconds from the moment the picture is
stored. In the middle of the sound recording, pressing the shutter button will
stop the voice memo.
INFORMATION
● A distance of 40cm between you and the camera (microphone) is the best
distance to record sound.
● The Voice memo can't be activated in Motion capture, Interval shots.
《21》
Macro(
)/ Down button
■ While the menu is showing, press the DOWN button to move from the main
menu to a sub menu, or to move down the sub menu. When the menu is not
showing, you can use the MACRO / DOWN button to take macro pictures. The
distance ranges are shown below. Press the Macro button until the desired
macro mode indicator displays on the LCD monitor.
INFORMATION
● When the macro mode is selected, it is possible that camera shake will
occur. Take care not to shake the camera.
● When you take a picture within 20cm in the Macro mode, select the FLASH
OFF mode.
■ In the Program, A, S, M modes, you can change the aperture value and shutter speed
by pressing this button.
[Auto macro (
)]
[Macro (
)]
[Super Macro (
■ Types of focus modes and focus ranges (W: Wide, T: Tele)
Mode
Focus Type
Auto
Auto
Auto
macro
Program
《22》
Normal
Focus range
Mode
W:80-Infinity
Macro
T:80-Infinity
W:10-Infinity
T:50-Infinity
W:80-Infinity
T:80-Infinity
Focus Type
)]
(Unit : cm)
Focus range
W:10~80
T:50~80
Program
Super
Macro
W:1~10
(Wide only)
Manual
focus
W:1-Infinity
T:50-Infinity
●Manual Focus : Where the automatic focusing is not
available, for example, in very dark
conditions, you can set the focus
manually. Please be careful when
using the manual focus as the picture
can be blurred easily.
●How to use the Manual Focus
1. Press the Macro button three times. Then Manual
Focus bar will be displayed.
2. Set the focal length by using the Up/ Down button.
Press the shutter button to capture an image.
Up button : moves the point of focus further away
Down button : moves the point of focus nearer
Macro(
)/ Down button
Focus lock
■ Available focusing method, by recording mode
(O: Selectable , X: Not selectable, ∞: Infinity focus range)
■ To focus on a subject not positioned in the centre of the picture, use the focus
lock function.
Mode
Normal
O
O
O
O
O
X
O
O
Macro
X
O
O
O
O
X
Auto Macro
O
X
X
X
X
O
X
Super Macro
X
O
O
O
O
X
O
Manual focus
X
O
O
O
O
X
X
SCENE
Mode
Normal
O
O
O
∞
X
X
Macro
X
X
X
X
X
O
Auto Macro
X
X
X
X
O
X
Super Macro
X
X
X
X
X
X
Manual focus
X
X
X
X
X
X
-
Mode
Normal
∞
∞
O
∞
O
-
Macro
X
X
X
X
X
-
Auto Macro
X
X
X
X
X
-
Super Macro
X
X
X
X
X
-
Manual focus
X
X
X
X
X
-
● Using the Focus Lock
1. Ensure the subject is in the centre of the autofocus frame.
2. Press the SHUTTER button halfway. When the green auto focus frame lights
up, it means the camera is focused on the subject. Be careful not to press the
SHUTTER button all the way down to avoid taking an unwanted picture.
3. With the SHUTTER button still pressed down only halfway, move the camera
to recompose your picture as desired, and then press the SHUTTER button
completely to take the picture. If you release your finger from the SHUTTER
button, the focus lock function will be cancelled.
1. The image to be
captured.
2. Press the SHUTTER
button halfway and focus
on the subject.
3. Recompose the picture
and fully press the
SHUTTER button.
《23》
Flash (
)/ Left button
■ When the menu is displayed on the LCD monitor,
pressing the LEFT button makes the cursor shift to
the left tab.
■ When the menu is not displayed on the LCD monitor,
the LEFT button operates as the FLASH
(
) button.
INFORMATION
[Selecting the Auto flash]
● Selecting the flash mode
1. Rotate the MODE DIAL to select a RECORDING mode with the exception of
MOVIE CLIP mode.
2. Press the Flash button until the desired flash mode indicator displays on the
LCD monitor.
3. A flash mode indicator will be displayed on the LCD monitor.
Use the correct flash to suit the environment.
(Unit : m)
● Flash range
ISO
AUTO
《24》
Normal
WIDE
TELE
0.8~3.0 0.8~2.5
Macro
WIDE
TELE
0.2~0.8 0.5~0.8
Auto macro
WIDE
TELE
0.2~3.0
0.5 ~2.5
● Using the flash frequently will reduce the life of the battery.
● Under normal operating conditions the charging time for the flash is
normally within 5 seconds. If the battery is weak, the charging time will be
longer.
● During the continuous shot, AEB, Motion capture, Interval shot and movie
clip mode, the flash function will not operate.
● Take photographs within the flash range.
● The image quality is not guaranteed if the subject is too close or highly
reflective.
● When taking an image in poorly lit conditions with the flash, there may be a
white speck in the captured image. The speck is caused by the reflecting of
the flash light from the atmospheric dust. It is not camera malfuction.
Flash (
)/ Left button
● Flash mode indicator
Menu tab
● Available flash mode, by recording mode
Flash mode
Description
Auto flash
If the subject or background is dark, the camera flash
will operate automatically.
Auto &
Red eye
reduction
Fill in flash
If a subject or background is dark, the camera flash
will work automatically and will reduce the red-eye
effect by using the red-eye reduction function.
The flash fires regardless of available light.
The intensity of the flash will be controlled, according to
the prevailing conditions. The brighter the background
or subject is, the less intense the flash will be.
Slow synchro
The flash will operate in conjunction with a slow
shutter speed in order to obtain the correct exposure.
When you take an image in a condition with poor
light, the camera shake warning indicator
(
) will display on the LCD monitor.
We recommend using a tripod for this function.
Flash off
The flash does not fire. Select this mode when
capturing images in a place or situation where flash
photography is prohibited. When you capture an image
in a poorly lit condition, the camera shake warning
indicator (
) will display on the LCD monitor. We
recommend using a tripod for this function.
(O : Selectable X : Not selectable)
X
X
O
X
X
X
X
O
O
X
X
X
X
X
X
X
O
O
O
O
X
X
X
O
X
X
X
X
O
O
O
O
O
O
O
Scene modes
X
X
X
X
X
X
X
X
X
X
O
X
O
O
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
O
X
X
O
X
X
X
X
X
X
X
X
X
X
O
O
O
O
O
O
O
O
X
O
X
《25》
Self-timer(
) / Right button
■ When the menu is displayed on the LCD monitor, pressing the Right button makes the
cursor shift to the right tab.
■ When the menu is not displayed on the LCD monitor, the RIGHT button operates as
the Self-timer( ) button. This function is used when the photographer would also
like to be in the image.
● Selecting the self-timer
1. Rotate the MODE DIAL to select a RECORDING
mode with the exception of VOICE RECORDING
mode.
2. Press the SELF-TIMER button until the desired
mode indicator displays on the LCD monitor.
A 10 second, 2 second or double self-timer icon
appears on the LCD monitor. In Movie Clip mode,
only the 10-second self-timer will work.
•10SEC self-timer (
)
: Pressing the shutter button will allow an interval
of 10 seconds before the image is taken.
•2SEC self-timer (
)
: Pressing the shutter button will allow an interval [Selecting the 10 SEC self-timer]
of 2 seconds before the image is taken.
•Double self-timer (
)
: A picture will be taken after about 10 seconds and 2 seconds later a
second picture will be taken. When using the flash, the 2-second self-timer
may be delayed for longer than 2 seconds depending on the flash charge
time.
3. When you press the SHUTTER button, the picture will be taken after the
specified time has elapsed.
《26》
INFORMATION
● If you operate the Self-timer and Play mode button during the self-timer
operation, the self-timer function is cancelled.
● Use a tripod to prevent the camera from shaking.
● In Movie Clip mode, only the 10SEC self-timer will work.
MENU / OK button
■ MENU button
- When you press the MENU button, a menu related to each camera mode will
be displayed on the LCD monitor. Pressing it again will return the LCD to the
initial display.
- A menu option can be displayed for MOVIE CLIP and STILL IMAGE.
There is no menu available when the VOICE RECORDING mode is selected.
SIZE
Pressing the MENU button
[Menu off]
3264X2448
3264X2176
3264X1824
2592X1944
2048X1536
1024X768
[Menu on]
■ OK button
- When the menu is displayed on the LCD monitor, this button is used for shifting
the cursor to the sub menu or for confirming data.
E (Effect) button
Special Effect : Colour
■ It is possible to add special effects to your images by using this button.
■ Still image mode : You can select the colour, outfocus, composite and frame
menus.
■ Movie clip mode : You can select the colour and stabiliser menus.
■ Available Effects, by recording mode (O : Selectable X : Not selectable)
■ By using the camera’s digital processor, it is possible to add special effects to
your images
1. Press the E button in any recording mode.
2. Select the
menu tab by pressing the Left/ Right button.
O
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
X
X
X
X
X
X
O
O
O
O
X
X
X
X
X
X
O
O
O
O
X
X
X
X
O
X
X
X
X
X
X
X
X
X
INFORMATION
● This button will not operate in the ASR, Voice recording and some scene
modes (Night, Text, Sunset, Dawn, Backlight, Firework, Beach & Snow).
● When
or
is selected, only
menu of the Effect menus can be
selected.
● If a special effect is selected, any previously selected special effects (preset
focus frames; composite shooting; photo frame) are cancelled
automatically.
● Even if the camera is turned off, the special effect setting will be preserved.
To cancel the special effect, select the
sub menu in the Colour menu
and select the
sub menu in the rest special effect menu.
Normal
[Still image mode]
Normal
[Movie clip mode]
3. Select a desired sub menu by pressing the Up/ Down button and press the
OK button.
: No effect is added to the image
: Captured images will be stored in black and white.
: Captured images will be stored in a sepia tone
(a gradient of yellowish brown colours).
: Captured images will be stored in a blue tone.
: Captured images will be stored in a red tone.
: Captured images will be stored in a green tone.
: Save the image in negative mode.
4. Press the shutter button to capture an image.
《27》
Special Effect : Preset focus frames
■ You can make the subject stand out from its
surroundings. The subject will be sharp and in focus
while making the rest out of focus.
1. Press the E button in the available camera
modes(Not available: Movie clip, Voice, Auto,
HighLight
Manual, ASR, Scene).
2. Select the
menu tab by pressing the Left / Right button.
3. Select a desired sub menu by pressing the Up / Down button and press the
OK button.
● Moving and changing the focus frame
You can change the focus frame after selecting a Range menu.
1. Point the camera towards the subject and compose the image by using the
LCD monitor.
2. Press the +/ - button.
3. The colour of focus frame turns white. Press the Up/ Down/ Left/ Right button
to move the focus frame position.
4. To select the focus frame position, press the +/ - button again and you can
take a picture.
Pressing the +/ - button
HighLight
[Range 1]
HighLight
[Range 2]
HighLight
[Range 3]
HighLight
Capture:SH
Edit:+/-
Capture:SH
[Range 3]
Move :
[The frame is activated]
4. The preset focus frame will appear.
Press the shutter button to capture an image
Pressing the Up/ Down/
Left/ Right button
Capture:SH
Edit:+/-
Pressing the +/ - button
Capture:SH
Edit:+/-
Capture:SH
Move :
[After changing the frame
position]
《28》
Special Effect : Composite shooting
■ You can combine 2 - 4 different shots in a still image
1. Press the E button in the available camera
modes(Not available: Movie clip, Voice, Auto,
Manual, ASR, Scene).
2. Select the
menu by pressing the Left/ Right
Composite
button.
3. Select a desired sub menu by pressing the Up/ Down button and press the
OK button.
-
: cancels the composite shooting
: 2 different shots are combined in a still image.
: 3 different shots are combined in a still image.
: 4 different shots are combined in a still image.
: 2 different panorama shots are combined in a still image.
4. The number of frames you selected in step 3 is displayed on the LCD monitor.
Press the shutter button to start the composite shooting
※ Selecting 2 composite shooting
Pressing the
shutter button
Pressing the
shutter button
Capture:SH
[Ready for taking]
Del : +/-
[First shot]
INFORMATION
● You can use the flash button, self-timer button, macro button, voice memo
button and the Zoom W / T button during the composite shooting.
● If you press the Play mode button or press the Voice recording button twice
during the composite shots, each camera working mode is executed.
The images captured before will be deleted.
● After taking the last composite shooting, press the OK button. And then the
voice memo will start.
● Changing a part of composite shot before taking the last shot
Before taking the last composite shot, you can change a part of composite shot.
1. During the composite shots, press the +/ - button.
2. A previous image will be deleted and new frame will display.
If there is an image taken before, press the +/ - button again and a previous
image will be deleted again.
Pressing the
OK button
Save : OK
Del : +/-
[Second shot]
Pressing the +/ - button
[The final picture]
Capture:SH
5. To save the composite shots, press the OK button after taking the last shot.
Del:+/-
[Before taking the 3rd shot]
Capture:SH
Del:+/-
[Moving backward to the 2nd
shot]
3. Press the shutter button to capture a new image.
《29》
Special Effect : Composite shooting
● Changing a part of composite shot after taking the last shot
1. After taking the last shot , a cursor to select a frame will display. Press the Up/
Down/ Left/ Right button to select the frame.
2. Press the +/ - button and an image will be deleted. Composite frame will be
activated.
3. Press the Shutter button. You can take other images again by using the Up/
Down/ Left/ Right button and +/ - button.
4. Press the OK button again to save the captured image.
Pressing the
Up button
Save : OK
Del : +/-
Save : OK
[After taking the 4th shot]
Del : +/-
[Moving backward to the 2nd shot]
Pressing the
+ / - button
Pressing the
Shutter button.
[Deleting the 2nd shot]
Pressing the OK
button
Save : OK
Del : +/-
[After taking the 2nd shot again]
《30》
[The final picture]
Special Effect : Photo Frame
■You can add 9 types of frame-like borders to a still image you want to capture.
■Date & Time information will not be printed on the stored image taken with Photo
Frame menu.
1. Press the E button in the available camera
modes(Not available: Movie clip, Voice, Auto,
Manual, ASR, Scene).
2. Select the
menu by pressing the Left/ Right
button.
3. Select a desired sub menu by pressing the Up/
Down button and press the OK button.
: The photo frame will not be added.
Photo Frame
Special Effect : Photo Frame
4. The photo frame will appear.
Press the shutter button to capture an image
+/ - button
■ You can use the +/ - button to adjust the values for the RGB, ISO, white balance
and exposure compensation.
Main menu
Sub menu
RGB
R (Red), G (Green), B (Blue)
ISO
AUTO, 50, 100, 200, 400, 800, 1600
WHITE
BALANCE
AUTO, DAYLIGHT, CLOUDY,
FLUORESCENT H,
FLUORESCENT L, TUNGSTEN,
CUSTOM.
Exposure
compensation
-2.0- 0.0 - + 2.0 (0.5EV steps)
Available camera mode
Movie Clip frame stabiliser
■ This function helps stabilise images captured during movie recording.
You can select this menu only in the MOVIE CLIP mode.
1. Press the E button in the Movie clip mode.
2. Press the Left/ Right buttons to select the
stabilizer menu tab.
3. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
Stabilizer
: Movie clip frame stabiliser function
becomes disabled.
: Reduces camera shake during movie recording.
The recording frame range will become narrower than when you
select the
menu. Pre-view frames may not display smoothly on
the LCD monitor.
※ If the memory card is not inserted, this function will not operate.
《31》
+/ - button
■ RGB : Allows the user to adjust the R (Red), G (Green), and B (Blue) values of
the images to be captured.
■ ISO : You can select the ISO sensitivity when taking pictures.
The speed or specific light-sensitivity of a camera is rated by ISO numbers.
● Setting RGB Values
1. Press the +/ - button, and then use the UP and
DOWN buttons to select the RGB icon (
).
The RGB menu bar will appear as shown.
2. Use the UP/ DOWN/ LEFT and RIGHT buttons
to select the desired RGB value.
- Up/ Down Button : Navigates between R, G,
and B icons.
- Left/ Right Button : Changes value of each icon.
3. When you press the +/ - button again, the value you set will be saved and
RGB setup mode will end.
※ When special effect (colour) from the icon other than
is selected, it will
not be able to select the RGB.
● Selecting an ISO Sensitivity
1. Press the +/ - button, and then use the UP and
DOWN buttons to select the ISO icon(
).
The ISO menu bar will appear as shown.
2. Use the LEFT and RIGHT buttons to select the
desired ISO sensitivity value.
- AUTO
: The camera's sensitivity is automatically
changed by variables such as lighting value or subject brightness.
- 50, 100, 200, 400, 800, 1600
: You can increase the shutter speed while the same amount of light is
present, by increasing the ISO sensitivity. However, the image may be
saturated in high luminance. The higher the ISO value, the higher the
camera’s sensitivity to light is and therefore the greater its capacity to take
pictures in dark conditions. However, the noise level in the image will
increase as the ISO value increases, making the image appear coarse.
3. When you press the +/ - button again, the value you set will be saved and ISO
setup mode will end.
《32》
+/ - button
■ White balance : The white balance control allows you to adjust the colours to
appear more natural.
● Selecting a White Balance
1. Press the +/ - button, and then use the UP and
DOWN buttons to select the white balance icon
(
). The white balance menu bar will appear
as shown.
2. Use the LEFT and RIGHT buttons to set the white
balance to the desired value. The value you set wil
be displayed on the LCD monitor.
AUTO
: The camera automatically selects the appropriate white
balance settings, depending on the prevailing lighting
conditions.
DAYLIGHT
: For taking images outside.
CLOUDY
: For taking images under a cloudy and overcast sky.
Fluorescent H
: For shooting under daylight fluorescent types of threeway fluorescent lighting.
Fluorescent L
: Shooting under white fluorescent lighting.
TUNGSTEN
: For shooting under tungsten (standard light bulb)
lighting.
CUSTOM
: Allows the user to set the white balance according to
the shooting condition.
Different lighting conditions may cause a colour cast on your images.
3. Press the +/ - button again. The value you set will be saved and White
Balance setup mode will end.
● Using the Custom White Balance
White balance settings may vary slightly depending on the shooting
environment. You can select the most appropriate white balance setting for a
given shooting environment by setting up the custom white balance.
1. Select the CUSTOM (
) menu of the White
Balance.
2. Place a sheet of white paper in front of the
camera so that the LCD monitor shows only
white, and then press the SHUTTER button.
3. Your custom white balance value is stored.
- The custom white balance value will be applied,
starting with the next picture you take.
- The user configured white balance will be
remain effective until it is overwritten.
Measure:Shutter
[White paper]
《33》
+ / - button
■ Exposure compensation : This camera automatically adjusts the exposure
according to the ambient lighting conditions.
You can also select the exposure value by using the
+ / - button.
● Compensating Exposure
1. Press the + / - button, and then use the UP and
DOWN buttons to select the exposure
compensation icon (
).
The exposure compensation menu bar will appear
as shown.
2. Use the LEFT and RIGHT buttons to set the desired exposure compensation
factor.
3. Press the + / - button again. The value you set will be saved and the Exposure
Compensation setup mode will close.
If you change the exposure value, the exposure indicator (
) will be
displayed on the bottom of the LCD monitor.
※ A negative exposure compensation value reduces the exposure.
Note that a positive exposure compensation value increases the exposure
and the LCD monitor will appear white or you may not get good pictures.
Using the LCD monitor to set the camera settings
■ You can use the menu on the LCD monitor to set up recording functions. In any
mode with the exception of VOICE RECORDING mode, pressing the MENU
button displays the menu on the LCD monitor.
※ The menu will not be displayed on the LCD monitor in the following circumstances:
- When another button is being operated.
- While image data is being processed.
- When there is no battery capacity.
■ The following functions are available, depending on the mode you have selected.
The items indicated by
are default settings.
Menu tab Main menu
SIZE
3264x1824 2592X1944
(Still image)
2048X1536 1024X768
SIZE
(Movie)
QUALITY
FRAME
RATE
800X592
720X480
640X480
320X240
Super Fine
Fine
Normal
-
*30 FPS
20 FPS
15 FPS
-
TIME
《34》
Camera working mode
Sub menu
Page
3264X2448 3264X2176
1S
p.36
p.36
p.36
p.36
p.38
METERING
Multi
Spot
p.37
AUTO FOCUS
Multi AF
Center AF
p.37
Using the LCD monitor to set the camera settings
Menu tab Main menu
Sub menu
Single
SHOOTING Motion Capture
SHARPNESS
Camera working mode
Continuous
AEB
Interval
-
Soft
Normal
Vivid
-
Full
OSD
INFORMATION LCD Save
Page
Basic
-
※ * 30 FPS cannot be used in 800X592, 720X480 size.
※ Menus are subject to change without prior notice.
How to use the menu
1. Turn on the camera and press the MENU button. A menu for each camera
mode appears. However, there is no menu for Voice Recording mode (
).
2. Use the LEFT and RIGHT buttons to navigate through the menus.
p.38
p.39
p.39
SIZE
3264X2448
3264X2176
3264X1824
2592X1944
2048X1536
1024X768
Press the
LEFT or
RIGHT button.
QUALITY
Super Fine
Fine
Normal
Press the
LEFT or
RIGHT button.
METERING
Multi
Spot
3. Use the UP and DOWN buttons to select a sub menu.
SIZE
3264X2448
3264X2176
3264X1824
2592X1944
2048X1536
1024X768
Press the UP
or DOWN
button.
SIZE
3264X2448
3264X2176
3264X1824
2592X1944
2048X1536
1024X768
Press the UP
or DOWN
button.
SIZE
3264X2448
3264X2176
3264X1824
2592X1944
2048X1536
1024X768
4. Select a sub menu, and then the value you set will be saved.
Press the MENU button and the menu will disappear.
《35》
Size
Quality/ Frame rate
■ You can select the image size appropriate for your application.
Mode
Still
image
mode
Movie clip
mode
Normal
■You can select the compression ratio appropriate for your application of the
captured images. The higher the compression ratio, the lower the picture quality.
Print angle Wide angle
Size
STILL IMAGE mode
Mode
Icon
3264X
2448
2592X
1944
2048X
1536
1024X
768
3264X
2176
3264X
1824
Icon
Size
800X592
720X480
640X480
Sub menu Super Fine
Fine
Normal
30FPS
20FPS
15FPS
File Format
jpeg
jpeg
avi
avi
avi
jpeg
320X240
QUALITY
Super Fine
Fine
Normal
SIZE
MOVIE CLIP mode
Icon
FRAME RATE
30 FPS
20 FPS
15 FPS
SIZE
3264X2448
3264X2176
3264X1824
2592X1944
2048X1536
1024X768
800X592
720X480
640X480
320X240
[STILL IMAGE mode]
[MOVIE CLIP mode]
[ STILL IMAGE mode ]
[ MOVIE CLIP mode ]
INFORMATION
INFORMATION
●The higher the resolution, the lower the number of shots available because
high resolution images require more memory.
《36》
● This file format complies with the DCF (Design rule for Camera File system).
● JPEG (Joint Photographic Experts Group) : JPEG is the image
compression standard developed by the Joint Photographic Experts Group.
This type of compression is most commonly used for compressing photos
and graphics because it can compress the files efficiently.
Metering
■ If you cannot obtain suitable exposure conditions, you can change the metering
method to take brighter pictures.
[Multi] : Exposure will be calculated based on an
METERING
average of the available light in the image
Multi
Spot
area. However, the calculation will be biased
towards the centre of the image area.
This is suitable for general use.
[Spot] : Only the rectangular area in the centre of
[ PROGRAM mode ]
the LCD monitor will be metered for light.
This is suitable when the subject in the
centre is exposed correctly, regardless of the back lighting.
※ If the subject is not the centre of the focus area, do not use the spot metering
as this may result in an exposure error. In this circumstance, it is better to use
exposure compensation.
Auto Focus type
■ You can select your preferred Auto Focus type according to the shooting condition.
- [Multi AF]
: This camera selects a AF point from
the 5 AF points.
- [Center AF] : The rectangular area in the center of
the LCD monitor will be focused
AUTO FOCUS
Multi AF
Center AF
[ PROGRAM mode ]
[Multi AF]
[Center AF]
※ When the camera focuses on the subject, the auto focus frame turns too green.
When the camera doesn’t focus on the subject, the auto focus frame turns to
red.
《37》
Continuous shot
■ You can select continuous shot, and AEB (Auto Exposure Bracketing).
- [Single]
- [Continuous]
: Take one picture only
SHOOTING
: Images will be taken
Single
Continuous
continuously until the shutter
Motion Capture
button is released. The shooting
AEB
Interval
01 min
capacity depends on the
02 Pic
memory.
[ PROGRAM mode ]
- [Motion Capture] : This takes 30 shots per second,
when the shutter is pressed and
held down. After completing the continuous shooting,
images are saved and the images play back on the Rear
LCD. The maximum number of shots is 30 and the image
size is fixed as 640X480.
- [AEB]
: Take three pictures in a series in different exposures: short
exposure (-0.5EV), standard exposure (0.0EV) and over
exposure (+0.5EV). Use the mode if it is hard to decide
exposure of the object.
- [Interval]
: You can take images with interval and number of images
set before.
Left / Right button : Selecting the Interval menu or Number
of image menu.
Up / Down button : Changing the numbers
(01 min-60 min / 02 pics-99 pics).
* After taking the first picture, the LCD monitor turns off.
After completing the Interval shot, the interval shot is
canceled.
* Before using the Interval shot, charge the battery fully.
If the battery is out during the shots, the last taken before
the camera was turned off.
《38》
INFORMATION
●High resolution and picture quality increases file saving time, which
increases stand-by time.
●If the [Continuous], [Motion capture] or [AEB] sub menu is selected, the flash
will be off automatically.
●If less than 3 pictures are available in the memory, the AEB shooting is not
available.
●It is best to use a tripod for the AEB shooting as the time to save each image
file is longer and blurring caused by camera shake may occur.
Sharpness
■ You can adjust the sharpness of the picture you
want to take. You cannot check the sharpness effect
on the LCD monitor before you take a picture,
because this function is applied only when the
captured image is stored on the memory.
OSD (On Screen Display) information
SHARPNESS
Soft
Normal
Vivid
■ In any mode with the exception of VOICE
RECORDING mode, you can check the recording
status in the LCD monitor.
OSD INFORMATION
Full
Basic
LCD Save
[ PROGRAM mode ]
Sub menu
Soft
Normal
Vivid
Icon
Description
The edges of the image are softened.
This effect is suitable for editing images on your PC.
The edges of the image are sharp.
This is suitable for printing.
The edges of the image are emphasized. The edges
will appear sharp, but noise may occur in the
recorded image.
[Full information]
[Basic information]
《39》
Starting play mode
■If the memory card is inserted in the camera, all the camera functions apply only
to the memory card.
■If the memory card is not inserted in the camera, all the camera functions apply
only to the internal memory.
■If you have turned on the camera by pressing the POWER button, you can press
the PLAY MODE button once to switch to Play mode and press it again to switch
to Recording mode.
■You can turn the power on with the play mode button. The camera is turned on in
play mode. Press the play mode button again and the camera will be turned off.
■You can set up the PLAY mode function by using the camera buttons and LCD
monitor.
● Playing back a still image
1. Select the PLAY mode by pressing the
play mode button (
).
2. The last image stored on the memory is
displayed on the LCD monitor.
3. Select an image that you want to play
back by pressing the LEFT/ RIGHT
button.
※ Press and hold the Left or Right button to
fast forward the images played.
《40》
INFORMATION
●Manner mode : Pressing the play mode button for more than 3 seconds
changes the buzzer and start-up sound setting to OFF, even
though you may have set these to ON.
●Lightly press the shutter button in Play mode to switch to the currently set
shooting mode.
● Playing back a movie clip
Steps from 1-2 are the same as those to play back
a still image.
3. Select the recorded movie clip and press the
Play & Pause button to play back.
- To pause a movie clip file while playing it back,
press the play & pause button again.
- Pressing the play & pause button again will
cause the movie clip file restart.
- To rewind the movie clip while it is playing,
press the LEFT button. To fast forward the
movie clip, press the RIGHT button.
- To stop playback of the movie clip, press the
play & pause button, and then press the LEFT
or RIGHT button.
Play: /
Starting play mode
■Movie clip capture function : capture still images from the movie clip.
■ On camera movie trimming : You can extract desired frames of movie clip during
the movie clip play back.
● How to capture the movie clip
Steps 1-3 are the same as those for playing back
a movie clip.
4. Press the Play / Pause button while playing the
movie clip. Then press the E button.
5. The paused movie clip is saved in a new file
name.
※ The captured movie clip file has same size as
the original movie clip (800X592, 720X480,
640X480, 320X240)
● If the running time is under 10 seconds, the movie
clip can’t be trimmed.
1. Press the Pause button at the point of the movie
clip that you want to start extracting.
2. Press the OK button. (The start point doesn't
display on the status bar, but the start point will be
marked.)
3. The movie plays back again and the extracted
range will be displayed on the status bar.
4. Press the Play & Pause button once more at the
point where you wish the extracted file to stop.
5. Press the OK button and a confirmation window
will display.
6. Select a desired sub menu by pressing the Left/
Right button and press the OK button.
[Yes] : The extracted frames are saved as a new
file name.
[No] : The movie trimming will cancel.
MARK IN:OK
Capture:E
00:00:05
[Paused]
[Pressing the E button]
MARK IN:OK
Capture:E
00:00:05
Play: /
OK:Trim
00:00:10
Trimming?
Yes
No
Confirm : OK
INFORMATION
●If the time line bar passes by the start point by pressing the REW (Left)
button, the first frame of the movie clip will display.
●If you don’t specify the ending point of the movie clip, the trimming
confirmation window will display at the point of the last frame.
《41》
Starting play mode
● Playing back a recorded voice
Steps from 1-2 are the same as those to play
back a still image.
3. Select the recorded voice file and press the
Play & Pause button to play back a recorded
voice file.
PLAY:
- To pause a recorded voice file, while playing
it back, press the play & pause button again.
- To resume playback of the voice file, press the play & pause button.
- To rewind the voice file while it is playing, press the LEFT button.
To fast forward the voice file, press the RIGHT button.
- To stop playback of the voice file, press the play & pause button, and then
press the LEFT or RIGHT button.
《42》
LCD monitor Indicator
■ The LCD monitor displays shooting information about the displayed image.
①
100-0007
⑫
Av:F2.8
Tv:1/30s
ISO:50
Flash:ON
3264X2448
2007/01/01
⑪
⑩
⑨
⑧
⑦
⑥
②
③
④
⑤
No.
Description
1
Play mode icon
Icon
Page
-
2
Battery
p.10
3
Voice Memo
p.21
4
Protect
p.53
5
DPOF
6
Recording date
2007/01/01
p.55
7
Image size
3264X2448 - 256X192
p.36
8
Flash
ON/ OFF
p.24
p.32
p.63
9
ISO
50 - 1600
10
Shutter speed
15 - 1/2000
p.15
11
Aperture value
F2.8 - F4.4
p.14
12
Folder name & File name
100-0007
p.62
Using the camera buttons to set the camera
■In Play mode, you can use the buttons on the camera to conveniently set up the
Play mode functions.
Thumbnail (
)/ Enlargement (
) button
●You can view multiple pictures, enlarge a selected picture, and crop and save a
selected area of an image.
●Thumbnail display
1. While an image is displayed on full screen, press the
thumbnail button.
2. The thumbnail display will highlight the image that
had been showing at the time the thumbnail mode
was selected.
3. Press the 5 function button to move to a desired
image.
4. To view an image separately, press the enlargement
button.
Thumbnail(
)/ Enlargement (
) button
● Image enlargement
1. Select an image that you want to enlarge and
press the enlargement button.
2. Different parts of the image can be viewed by
pressing the 5 function button.
3. Pressing the thumbnail button will zoom back to
the original full sized image.
- You can tell whether the image displayed is an
enlarged view by checking the image
enlargement indicator shown at the top left of
the LCD monitor. (If the image is not an
enlarged view, the indicator will not be displayed.) You can also check the
area of enlargement.
- Movie clips and WAV files can’t be enlarged.
- If an image is enlarged, a loss of quality may occur.
Pressing the thumbnail
button (
)
Pressing the enlargement
button (
)
Highlighted image
[ Normal display mode ]
[ Thumbnail display mode ]
《43》
Thumbnail (
)/ Enlargement (
) button
●The maximum enlargement rate in proportion to the image size.
Image size
8M
7MP
6MW
5M
3M
1M
Maximum enlargement rate
X12.0
X11.3
X9.5
X9.0
X8.0
X4.0
●Trimming : You can extract part of the image that you
want and save it separately.
Trimming?
1. Select an image that you want to enlarge and
No
Yes
press the enlargement button. Press the Menu
Confirm : OK
button and a message will be displayed.
2. Select a desired sub menu by pressing the
Left/ Right button and press the OK button.
[Yes] : The trimmed image will save as a new file name, and display on the
LCD monitor.
[No] : The trimming menu will disappear.
※ If there is little memory space to save the trimmed image, the image can’t be
trimmed.
※ To delete the enlarged image during the trimming function, press the delete
button.
《44》
Voice (
) memo/ Up button
■When the menu is displayed on the LCD monitor, pressing the UP button makes
the menu cursor move up.
■When the menu is not displayed on the LCD monitor, the UP button operates as
the voice memo button. You can add your voice to a stored still image.
●Adding a Voice Memo to a Still Image
1. Press the LEFT/ RIGHT button to select an
image that you wish to add sound to.
2. Press the voice memo button ( ) and the voice
memo indicator will display. The camera is now
ready to record a voice memo.
Record:Shutter
00:00:00
3. Press the shutter button to start recording and
voice will be recorded to the still image for 10
seconds. While the voice is recording, the
recording status window will be displayed as
shown alongside.
4. The recording can be stopped by pressing the
shutter button again.
Stop:Shutter
00:00:05
5. The (
) icon will be displayed on the LCD
monitor after voice memo recording has finished.
- Voice memos can’t be recorded onto movie clip
and voice recording files.
- A distance of 40cm between you and the
camera (microphone) is the best distance to
record sound.
- The voice memo will be saved in .wav format, but has the same file name
as the still image to which it corresponds.
- If you add a new voice memo to the still image that already has a voice
memo, the existing voice memo will be erased.
Play & Pause (
)/ Down button
■In Play mode, the play & pause/ down button works as follows:
- If the menu is displayed
Press the DOWN button to move from the main menu to a sub menu, or to
move down the sub menu cursor.
- If a still image with a voice memo, a voice file, or a movie clip is playing
In Stop mode : Plays a still image with a voice memo, a voice file, or a
movie clip.
During playback : Temporarily stops playback.
In Pause mode : Resumes playback
PLAY:
STOP : Shutter
REW
[Voice recording is stopped]
PAUSE:
PLAY:
EXIT:OK
E (Effect) button
■ It is possible to add special effects to your images by using this button.
1. Select a still image or movie clip and press
the E button.
2. Select a desired sub menu and press the
OK button.
: Captured images will be stored in
black and white.
: Captured images will be stored in a sepia tone
(a gradient of yellowish brown colours).
: Captured images will be stored in a blue tone.
: Captured images will be stored in a red tone.
: Captured images will be stored in a green tone.
: Save the image in negative mode.
Exit:E
FF
[Voice recording is playing]
[Voice recording is paused]
※ The changed image is saved in a new file name.
《45》
Delete (
) button
■This deletes images stored on the memory.
●Deleting Images in Thumbnail Display Mode
1. Use the UP, DOWN, LEFT, and RIGHT buttons to select the image you want
to delete, and then press the DELETE (
) button.
2. A message will display on the LCD monitor as shown below.
3. Select the sub menu values by pressing the LEFT/ RIGHT button and then
press the OK button.
If [Yes] is selected : deletes the selected images.
If [No] is selected : cancels "Delete Image".
●Deleting Images in Play Mode
1. Select an image that you want to delete by
pressing the LEFT/ RIGHT button and press the
DELETE(
) button.
2. A message will display as shown alongside on
the LCD monitor.
3. Select the sub menu values by pressing the LEFT/
RIGHT button and then press the OK button.
If [Yes] is selected : deletes the selected images.
If [No] is selected : cancels "Delete Image".
Press the
delete button.
Delete?
Yes
Delete?
Yes
No
No
Confirm : OK
Confirm : OK
INFORMATION
●Before deleting images from the camera, you should protect or download
images to your computer that you wish to keep.
《46》
Printer button
Left/ Right/ Menu/ OK button
■ If you select [Computer] sub menu in the [USB]
setup menu, [Connecting Computer] message will
display when you connect the camera to your
printer and the connection will not be established.
In this case, press the Printer button. [Connecting
Printer] message will display and the Easy printing
mode will be selected.
■ LEFT/ RIGHT/ MENU/ OK buttons activate the following.
- LEFT button
* In some instances the camera may not connect to the printer, this will depend on
the manufacturer of the printer.
- After the connection, the Easy printing menu will
display on the LCD monitor.
To display the PictBridge menu, press the Menu
button. For more information about the PictBridge
menu, refer to page 57.
IMAGES
One Pic
All Pics
: While the menu is showing, press the LEFT button to select
the menu tab to the left of the cursor. While the menu is not
showing, press the LEFT button to select the previous image.
- RIGHT button : While the menu is showing, press the RIGHT button to select
the menu tab to the right of the cursor, or to move to a
secondary menu. While the menu is not showing, press the
RIGHT button to select the next image.
- MENU button : When you press the MENU button, the play mode menu will
be displayed on the LCD monitor. Pressing it again will return
the LCD to the initial display.
- OK button
: When the menu is displayed on the LCD monitor, the OK
button is used for confirming data that is changed by using the
5 function button.
Move:
《47》
Setting up the play back function using the LCD monitor
■ PLAY mode functions can be changed by using the LCD monitor. In the PLAY
mode, pressing the MENU button displays the menu on the LCD monitor. The
menus you can set up in Play mode are as follows. To capture an image after
setting up the play menu, press the PLAY mode button or shutter button.
Menu tab
Main menu
Sub menu
Secondary menu
Show
Play/ Repeat Play
Interval
1, 3, 5, 10 sec
SLIDE
Off
Menu tab
Main menu
Page
RESIZE
p.50
Effect
OSD
INFORMATION
ROTATE
Music
Off / Music 1,2,3
Full
-
Basic
-
OSD Off
-
Right 90˚
-
Left 90˚
-
180˚
-
Horizontal
-
Vertical
《48》
-
PROTECT
Sub menu
Secondary menu
2592 X 1944
-
2048 X 1536
-
1024 X 768
-
3M P (2016 X 1344)
-
1M P (1032 X 688)
-
2M W (1920 X 1080)
-
1M W (1280 X 720)
-
User Image 1, 2
-
Select
Unlock/ Lock
Page
p.52
p.53
All Pics
p.51
DELETE
COPY TO
CARD
p.51
DPOF
Select
-
All Pics
-
No
-
Yes
-
Standard
Select/ All Pics/ Cancel
Index
No/ Yes
Size
Select/ All Pics/ Cance
p.53
p.54
p.55
p.56
Setting up the play back function using the LCD monitor
■ This menu is available while the camera is connected to a PictBridge supporting
printer (direct connection to the camera, sold separately) with a USB cable.
Menu tab
Main menu
IMAGES
AUTO SET
Sub menu
Secondary menu
One Pic
-
All Pics
-
No
-
Yes
-
Menu tab
Main menu
Sub menu
Type
p.57
Auto
CUSTOM
SET
Quality
Date
L
2L
Full
1
2
Layout
4
8
9
Off
Auto
File Name
A4
A3
p.58
On
Letter
Auto
Normal
Auto
4X6
CUSTOM
SET
Draft
Fine
Card
Size
Plain
Photo
FastPhoto
p.58
PostCard
Page
Auto
Page
Auto
Secondary menu
Off
On
p.58
PRINT
DPOF PRINT
RESET
Standard
-
Index
-
No
-
Yes
-
No
-
Yes
-
p.59
p.60
p.60
※ Menus are subject to change without prior notice.
16
Index
《49》
Starting the slide show
■ Images can be displayed continuously at pre-set intervals.
You can view the slide show by connecting the camera to an external monitor.
1. Press the play mode button and press the menu button.
2. Press the LEFT / RIGHT button and select the [SLIDE] menu tab.
● Start the slide show : The slide show can start only in the [Show] menu.
1. Use the Up/ Down buttons to select the [Show]
menu and press the Right button.
SLIDE
Show
Play
2. Select a desired sub menu by pressing the
Interval
Repeat Play
Effect
Up/ Down button.
Music
[Play] : The slide show is closed after one cycle.
Back:
Set:OK
[Repeat Play] : The slide show is repeated until
cancelled.
3. Press the OK button and the slideshow will be
started.
● Setting play interval : Set the slide show play interval.
1. Select the [Interval] sub menu by pressing the
UP/ DOWN button and press the RIGHT button.
2. Use the Up/ Down buttons to select the desired
interval.
3. Press the OK button to save the configuration.
1 sec
3 sec
5 sec
10 sec
Back:
INFORMATION
● The loading time depends on the image size and quality.
● While the slide show is playing, only the first frame of a MOVIE file is
displayed.
● While the slide show is playing, the voice recording file will not display.
《50》
3. Press the OK button to confirm the setting.
● Setting B.G.M: Set the slide show music.
SLIDE
Show
Interval
Effect
Music
● Configure slide show effects : Unique screen effects can be used for the slide
show.
1. Select the [Effect] sub menu by pressing the
UP/ DOWN button and press the RIGHT button.
SLIDE
Show
Off
2. Use the Up/ Down button to select the type of
Interval
Effect
effect.
Music
Off : Normal display.
Back:
Set:OK
: Image is displayed slowly.
: Image is displayed slowly from the centre
outwards.
: Image moves from the top left.
: The image slides diagonally from top left to bottom right.
: The image slides irregularly.
Set:OK
1. Select the [Music] sub menu by pressing the UP/
DOWN button and press the RIGHT button.
2. Use the Up/ Down buttons to select the desired
Music.
3. Press the OK button to save the configuration.
SLIDE
Show
Interval
Effect
Music
Back:
Off
Music1
Music2
Music3
Set:OK
On Screen Display information
■ You can check shooting information about the displayed image.
● How to select the type of information you want to see
1. Press the play mode button and press the menu
button.
2. Select the [OSD INFORMATION] menu tab by
pressing the LEFT/ RIGHT button.
3. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
100-0007
OSD INFORMATION
Full
Basic
OSD Off
■ You can rotate the stored images by various degrees. Once the playback of the
rotated picture is finished, it will switch back to the original state.
1. Press the play mode button and press the menu
button.
2. Press the LEFT/ RIGHT button and select the
[ROTATE] menu tab.
3. Select a desired sub menu by pressing the UP/
DOWN button.
ROTATE
Right 90˚
Left 90˚
180˚
Horizontal
Vertical
Exit:MENU
Move:
100-0007
Av:F2.8
Tv:1/30s
ISO:50
Flash:ON
3264X2448
2007/01/01
[Full]
Rotating an image
[Right 90˚] :
Rotate picture in a
clock-wise direction
[Basic]
[Left 90˚] :
[180˚] :
Rotate picture in a counter- Rotate picture 180
clock-wise direction
degrees
[OSD Off]
[Horizontal] :
Rotate picture horizontally
[Vertical] :
Rotate picture vertically
4. Press the OK button. The rotated image will be saved with a new file name
and the menu will disappear. If you display the rotated image on the LCD
monitor, empty spaces may appear to the left and right of the image.
《51》
Resize
■ Change the resolution (size) of pictures taken. Select the [User Image] to save
an image to be the start-up image. The resized image will have a new file name.
1. Press the play mode button and press the menu
RESIZE
button.
2592X1944
2. Press the LEFT/ RIGHT button and select the
2048X1536
1024X768
[RESIZE] menu tab.
User Image1
User Image2
3. Select a desired sub menu by pressing the UP/
Exit:MENU
Move:
DOWN button and press the OK button.
● Image Resize Types
2592X1944
2048X1536
1024X768
User Image 1,2
8M
O
O
O
O
5M
X
O
O
O
3M
X
X
O
O
1M
X
X
X
2016X1344
7MP
6MW
《52》
1032X688
O
User Image 1,2
O
O
O
1920X1080
1280X720
User Image 1,2
O
O
O
● A large sized image can be resized to a smaller sized image, but not vice versa.
● Only JPEG images can be resized. Movie clip (AVI), Voice recording (WAV) files
can’t be resized.
● You can change the resolution of only those files compressed in the JPEG 4:2:2
format.
● The resized image will have a new file name. The [User Image] image is stored
not on the memory card but on the internal memory.
● Only two [User Image] images can be saved.
● If the memory capacity is insufficient to store the resized image, a [Memory Full!]
message will display on the LCD monitor and the resized image will not be stored.
Protecting images
Deleting images
■ This is used to protect specific shots from being accidentally erased (Lock).
It also unprotects images that have been previously protected (Unlock).
● Protecting Images
1. Press the play mode button and press the menu
button.
2. Press the LEFT/ RIGHT button and select the
[PROTECT] menu tab.
3. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
[Select ] : Selection window for an image to be
protected/released is displayed.
- Up/ Down/ Left/ Right : Select an image
- Zoom W/ T Button : Protect/ release the image
- OK button
: Your changes will be
saved and the menu will
disappear.
[All Pics] : Protect/ release all saved images
- Zoom W/ T Button : Protect/ release the images
- OK button
: Your changes will be saved
and the menu will
disappear.
- If you protect an image, the protect icon will be
displayed on the LCD monitor. (An unprotected
image has no indicator)
- An image in LOCK mode will be protected from
the delete function or [Delete] functions, but will
NOT be protected from the [Format] function.
■ Of all the files stored in the memory card, the unprotected files in the DCIM
subfolder will be deleted. Remember that this will permanently delete
unprotected images. Important shots should be stored on a computer before
deletion takes place. The startup image is stored in the camera's internal
memory (i.e., not on the memory card) and it will not be deleted even if you
delete all files on the memory card.
PROTECT
Select
All Pics
Exit:MENU
W
W
Move:
Unlock
Set:OK
Unlock
Set:OK
T
T
● Deleting images
1. Press the play mode button and press the menu
DELETE
button.
Select
2. Press the LEFT/ RIGHT button and select the
All Pics
[Delete] menu tab.
3. Select a desired sub menu by pressing the UP/
Exit:MENU
Move:
DOWN button and press the OK button.
[Select] : Selection window for an image to delete
is displayed.
- Up/ Down/ Left/ Right : Select an image
- Zoom T Button : Select the image for deletion.
Select:T
(
mark)
Del:OK
- OK Button : Press the OK button to display the
confirmation message. Select the
[Yes] menu and press the OK button
Delete?
to delete
marked images.
Yes
No
[All Pics] : Displays confirmation window. Select
Confirm : OK
the [Yes] menu and press the OK
button to delete all unprotected images.
If there aren’t protected images, all the
images are deleted and a [No Image!] message will display.
4. After deletion, the screen will be changed to the play mode screen.
《53》
Copy To Card
■ This enables you to copy image files, movie clips and voice recording files to the
memory card.
● Copying to the Memory Card
1. Press the play mode button and press the menu
COPY TO CARD
button.
No
Yes
2. Select the [COPY TO CARD] menu tab by
pressing the LEFT/ RIGHT button.
3. Select a desired sub menu by pressing the UP/
Exit:MENU
Move:
DOWN button and press the OK button.
- [No] : Cancels "Copy to Card".
- [Yes] : All images, movie clips and voice recording files saved in the internal
memory are copied to the memory card after the [Processing!]
message is displayed. After copying has been completed, the
screen will return to play mode.
《54》
INFORMATION
● When this menu is selected without inserting a memory card, you can select
the [COPY TO CARD] menu but the menu can’t be run.
● If there is not enough space available in the memory card to copy saved
images in the internal memory (20MB), the [COPY TO CARD] command
will copy only some of the images and display [Memory Full!] message.
Then the system will return to the playback mode. Please be sure to delete
any unnecessary files to free up space before inserting the memory card
into the camera.
● When you move the images that are stored in the internal memory by doing
[COPY TO CARD] to the card, the next number of file names will be created
in the card to avoid duplication of the file name.
- When the [Reset] of the [File] setup menu is set : The copied file names
start from after the last stored file name.
- When the [Series] of the [File] setup menu is set : The copied file names
start from after the last captured file name. After completing [COPY TO
CARD], the last stored image of the last copied folder is displayed on the
LCD monitor.
DPOF
■DPOF(Digital Print Order Format) allows you to embed printing information on
your memory card’s MISC folder. Select the pictures to be printed and how many
prints to make.
■The DPOF indicator will display on the LCD monitor when an image that has
DPOF information plays back. Images can then be printed on DPOF printers, or
at an increasing number of photo labs.
■This function is not available for Movie clips and Voice recording files.
■When the wide angle image is printed as a wide angle print, 8% of the left and
right side of the image may not be printed. Check that your printer can support
the wide angle image when you print the image. When you print the image at a
photo lab, request that the image is printed as a wide angle image. (Some photo
labs may not support the wide angle size print.)
DPOF : Standard
■ This function allows you to embed printing quantity information on a stored
image.
1. Press the play mode button and press the menu
button.
2. Press the LEFT/ RIGHT button and select the
[DPOF] menu tab.
3. Select the [Standard] menu by pressing the UP/
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
[Select] : Selection window for an image to print is
displayed.
- Up/ Down/ Left/ Right : Select an image to print.
- Zoom W/ T Button : Select the number of
prints.
[All Pics] : Configure number of prints for all
pictures except movie and voice files.
- W/ T button : Select a number of prints
[Cancel] : Cancel the print setup.
5. Press the OK button to confirm the setting.
If an image carries DPOF instructions, the DPOF
indicator (
) will show.
DPOF
Standard
Index
Size
Select
All Pics
Cancel
Back:
Set:OK
W
W
0 Prints
Set:OK
0 Prints
T
T
Set:OK
《55》
DPOF : Index
DPOF : Print size
■ Images (except for movie clips and voice file) are printed as index type.
1. Press the play mode button and press the menu
button.
Standard
Index
2. Press the LEFT/ RIGHT button and select the
Size
[DPOF] menu tab.
3. Select the [Index] menu by pressing the UP/
Back:
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/
DOWN button.
If [No] is selected : Cancel the index print setting.
If [Yes] is selected : The image will be printed in index format.
5. Press the OK button to confirm the setting.
■ You can specify the print size when printing images stored on the memory card.
The [Size] menu is available only for DPOF 1.1 compatible printers.
DPOF
No
Yes
Set:OK
● Setting the Print Size
1. Press the play mode button and press the menu
button.
2. Press the LEFT/ RIGHT button and select the
[DPOF] menu tab.
3. Select the [Size] menu by pressing the UP/
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
[Select] : Selection window for an image to be
changed printed size is displayed.
- Up/ Down/ Left/ Right : Select an image.
- Zoom W/ T Button : Change the print size.
- OK button
: Your changes will be
saved and the menu will
disappear.
[All Pics] : Change print size of all saved images.
- W/ T button : Select a print size
- OK button : Confirm the changed setting.
[Cancel] : Cancel all of the print size settings.
DPOF
Standard
Index
Size
Select
All Pics
Cancel
Back:
Set:OK
W
W
Cancel
Set:OK
Cancel
T
T
Set:OK
※ DPOF [Size] secondary menu : Cancel, 3X5, 4X6, 5X7, 8X10
INFORMATION
● Depending on the manufacturer and print model, cancelling the printing may
take a little longer for the printer to process.
《56》
PictBridge
PictBridge : Picture Selection
■ You can use the USB cable to connect this camera to a printer that supports
PictBridge (sold separately) and print the stored images directly. Movie clips and
voice files cannot be printed.
● Setting up the camera for connection with the printer
1. In any mode with the exception of Voice Recording
mode, press the MENU button.
2. Press the LEFT/ RIGHT button and select
[SETUP] menu tab.
3. Select [USB] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Select [Printer] menu by pressing the UP/ DOWN
button and press the OK button.
SETUP
AF Lamp
Sound
USB
LCD
Video Out
Back:
※ If you selected [Computer] in Step 4, when you connected the camera to your
printer, the [Connecting Computer] message will display and the connection will
not be established. In this case, disconnect the USB cable, and then follow the
procedure from Step 2 and onward. Or, press the Printer button and the camera
is connected to the printer displaying the [Connecting Printer] message. But, the
camera may not connect to the printer, depending on the manufacturer and
model of the printer.
Computer
Printer
Set:OK
■ Easy printing
When you connect the camera to printer in the Play
back mode, you can print a picture easily.
- Pressing the printer(
) button :
Currently displayed image will be printed with the
printer’s default setting.
- Pressing the Left / Right button :
Selects a previous / next image.
Print:
Menu:OK
■ Select pictures to print
1. Press the Menu button.
2. The [IMAGES] menu will appear.
IMAGES
One Pic
3. Use the UP and DOWN buttons to select the
All Pics
desired sub menu value, and then press the OK
button.
Move:
Set:OK
When [One Pic] is selected
: The PictBridge function will be applied only to the
picture currently displayed.
When [All Pics] is selected
: The PictBridge function will be applied to all pictures, excluding movie clips
and voice files.
《57》
PictBridge : Picture Selection
● Setting the Number of Copies to Print
- Select [One Pic] or [All Pics]. A screen where you can set the number of copies
to print will appear as shown below.
W
W
Set:OK
0 prints
T
Exit:Shutter
[When [One Pic] is selected]
Set:OK
0 prints
T
Exit:Shutter
■ AUTO SET
1. Use the LEFT and RIGHT buttons to select the
[AUTO SET] menu tab.
2. Use the UP and DOWN buttons to select the
desired sub menu value, and then press the OK
button.
[No] : [CUSTOM SET] values are kept.
[Yes] : All values in the [CUSTOM SET] are
automatically changed.
AUTO SET
No
Yes
Move:
[When [All Pics] is selected]
- Press the Up/ Down button to select the number of prints.
- When [One Pic] is selected : Use the Left/ Right button to select another
picture. After selecting another picture, select the number of prints for another
picture.
- After setting the number of prints, press the OK button to save.
- Press the Shutter button to return to the menu without setting the number of
prints.
《58》
PictBridge : Print Setting
■ Custom Set : You can select the Paper Size, Print Format, Paper Type, Print
Quality, Date Print, and File Name Print menus for printed pictures.
1. Use the LEFT and RIGHT buttons to select the
[CUSTOM SET] menu tab.
2. Use the UP and DOWN buttons to select the
desired sub menu value, and then press the
RIGHT button.
3. Use the UP and DOWN buttons to select the
desired sub menu value, and then press the OK
button.
CUSTOM SET
Size
Layout
Type
Quality
Date
Move :
Auto
Auto
Auto
Auto
Auto
PictBridge : Print Setting
Menu
Size
Layout
Type
Function
Setting the size of the printing
paper
Sub menu
Auto, PostCard, Card, 4x6, L, 2L,
Letter, A4, A3
Setting the number of pictures to
Auto, Full, 1, 2, 4, 8, 9, 16, Index
be printed on a sheet of paper
Setting the quality of the printing
Auto, Plain, Photo, FastPhoto
paper
Quality
Setting the quality of the picture
to be printed
Auto, Draft, Normal, Fine
Date
Setting whether to print the date
Auto, Off, On
Setting whether to print the file
File Name
name
Auto, Off, On
※ Some menu options are not supported in all manufacturer and printer models.
If not supported, the menus are still displayed in the LCD, but are not selectable.
※ If the setting values are not changed in the automatic / manual setting, the
setting values are automatically kept.
PictBridge : Printing
■ Printing Pictures
1. Use the LEFT and RIGHT buttons to select the [PRINT] menu tab.
2. Use the UP and DOWN buttons to select the desired sub menu value, and
then press the OK button.
[Standard] : Print the pictures stored in the
PRINT
memory card in set numbers.
Standard
Index
One picture is printed on one piece of
paper.
[Index]
: Print multiple images on one sheet of
Move:
paper.
3. The screen shown on the right will appear and
the picture will be printed. If no picture is
selected, the [No Image!] message will be
displayed. Press the LEFT button while printing
to cancel the printing and the [PRINT] menu is
displayed.
※ Number of pictures in an index print varies
depending on the printer used.
Now Printing
0001 / 0001
Exit:Shutter
《59》
PictBridge : DPOF Printing
PictBridge : Reset
■ DPOF Print : This allows you to directly print the files with DPOF information.
1. Use the LEFT and RIGHT buttons to select the
[DPOF PRINT] menu tab.
2. Use the UP and DOWN buttons to select the
desired sub menu value, and then press the
OK button.
[No] : Cancel the printing
[Yes] : Directly print the file with the DPOF
information.
DPOF PRINT
No
Yes
Move:
※ Depending on the manufacturer and printer model, some menus may not be
available.
When a printer does not support DPOF, the menu is still displayed but not
available.
《60》
■ Initialises user-changed configurations.
1. Use the LEFT and RIGHT buttons to select the
[RESET] menu tab.
2. Use the UP and DOWN buttons to select the
desired sub menu value, and then press the OK
button.
If [No] is selected : Settings will not be reset.
If [Yes] is selected : All print and image settings
will be reset.
RESET
No
Yes
Move:
※ Default print setting varies depending on the printer manufacturer.
For your printer’s default setting, refer to the user’s guide that came with your
printer.
Setup menu
■In this mode, you can set up basic settings. You can use the setup menu in all
camera modes, except Voice Recording mode.
The items indicated by
are default settings.
Menu tab
Main menu
File
Power Off
Language
Format
Date&Time
World Time
Sub menu
Secondary menu
Page
Series
p.62
Reset
Off, 1, 3, 5, 10min
p.62
ENGLISH
FRANÇAIS
DEUTSCH ESPAÑOL
ITALIANO
P”CCK»…
p.62
PORTUGUÊS
DUTCH
DANSK
SVENSKA
SUOMI
BAHASA
POLSKI
Magyar
No
p.63
Yes
07/01/01 13:00
yy/mm/dd
p.63
mm/dd/yy
dd/mm/yy
Off
Cape Verde
Okhotsk
London
Wellington, Auckland
Rome, Paris, Berlin
Samoa, Midway
Athens, Helsinki
Honolulu, Hawaii
p.64
Moscow
Alaska
Abu Dhabi
LA, San Francisco
Tashkent
Denver, Phoenix
Almaty
Chicago, Dallas
Menu tab
Main menu
World Time
Imprint
AF Lamp
Sound
USB
LCD
Video Out
Quick View
Reset
Sub menu
Bangkok, Jakarta
Beijing, Hong Kong
Seoul, Tokyo
Guam, Sydney
Off
Date
Date&Time
Off
On
Off
Low
Medium
High
Computer
Printer
Dark
Normal
Bright
NTSC
PAL
Off/ 0.5, 1, 3sec
No
Yes
Secondary menu
New York, Miami
Caracas, La Paz
Buenos Aires
Mid-Atlantic
-
Page
p.64
p.64
p.64
p.64
p.65
p.65
p.65
p.66
p.66
※ Menus are subject to change without prior notice.
《61》
Setup menu
[ File name ]
[ Auto power off ]
■ This function allows the user to select the file naming format.
■ This function switches the camera off after a set amount of time in order to
prevent unnecessary battery drainage.
● Assigning File Names
1. In any mode with the exception of Voice
SETUP
Recording mode, press the MENU button.
Series
File
2. Press the LEFT/ RIGHT button and select the
Reset
Power Off
Language
[SETUP] menu tab.
Format
Date&Time
3. Select the [File ] menu by pressing the UP/
Back:
Set:OK
DOWN button and press the RIGHT button.
4. Select a desired sub menu by pressing the UP/
DOWN button and press the OK button.
[Series] : New files are named using numbers that follow the previous
sequence, even when a new memory card is used, or after
formatting, or after deleting all pictures.
[Reset] : After using the reset function, the next file name will be set from
0001 even after formatting, deleting all or inserting a new memory
card.
5. Press the menu button twice and the menu will disappear.
- The first stored folder name is 100SSCAM, and the first file name is
SS850001.
- File names are assigned sequentially from SS850001 → SS850002 → ~ →
SS859999.
- The folder number is assigned sequentially from 100 to 999 as follows:
100SSCAM → 101SSCAM → ~ → 999SSCAM.
- The files used with the memory card conform to the DCF (Design rule for
Camera File systems) format. If you change the image file name, the image
may not play back.
《62》
● Sub menus
[Off]
: The power off function will not
operate.
[1, 3, 5, 10 min] : The power will turn off
automatically if not used for the
period of time specified.
SETUP
File
Power Off
Language
Format
Date&Time
Off
1 min
3 min
5 min
10 min
Back:
Set:OK
- After replacing the battery, the power off setting will
be preserved.
- Note that the automatic power off function will not operate if the camera is in
PC mode, slide show, playing back a voice recording, playing back a movie clip
and taking a composite shot.
[ Language ]
■ There is a choice of languages that can be displayed on the LCD monitor.
Even if the battery is removed and inserted again, the language setting will be
preserved.
- LANGUAGE sub menu :
English, Korean, French, German, Spanish,
Italian, S.Chinese, T.Chinese, Russian,
Portuguese, Dutch, Danish, Swedish, Finnish,
Thai, BAHASA(MALAY/ INDONESIAN), Arabic,
Czech, Polish, Hungarian and Turkish.
SETUP
File
Power Off
Language
Format
Date&Time
Back:
ENGLISH
한국어
FRANÇAIS
DEUTSCH
ESPAÑOL
Set:OK
Setup menu
[ Formatting a memory ]
[ Setting up the Date/ Time/ Date type ]
■ This is used for formatting the memory. If you run [Format] on the memory, all
images, including the protected images, will be deleted. Be sure to download
important images to your PC before formatting the memory.
■ You can change the date and time that will be displayed on the captured images
and set up the date type.
● Sub menus
[No] : The memory will not be formatted. Press the
menu button three times and the menu
display will disappear.
[Yes] : A [Processing!] message appears and the
memory will be formatted. If you run
FORMAT in Play mode, a [No Image!]
message will appear.
SETUP
Power Off
Language
Format
Date&Time
World Time
Back:
No
Yes
Set:OK
Be sure to run [Format] on the following types of memory card.
- A new memory card, or an unformatted memory card
- A memory card that has a file this camera can't recognise or one that has been
taken from another camera.
- Always format the memory card using this camera. If you insert a memory card
that has been formatted using other cameras, memory card readers, or PCs,
you will get a [Card Error!] message.
● Setting Date/ Time & Selecting Date Format
RIGHT button : Selects the year/ month/ day/
hour/ minute date type.
LEFT button : Moves the cursor to the
[Date&Time] main menu if the
cursor is at the first item of the
date and time setup. In all other
cases, the cursor will be shifted to
the left of its current position.
UP and DOWN buttons : Changes the setting value
- Date type : [yy/mm/dd], [mm/dd/yy], [dd/mm/yy], [Off]
SETUP
Language
Format
Date&Time
World Time
Imprint
Back:
▲
07/01/01
▼
13:00
yy/mm/dd
Set:OK
《63》
Setup menu
[ World Time ]
[ Auto Focus lamp ]
■ This menu enables you to display the local date and time on the LCD monitor.
■ You can turn on and off the Auto Focus lamp.
SETUP
Format
Date&Time
World Time
Imprint
AF Lamp
Back:
● Sub menus
[Off] : The AF lamp will not light up in a low light
condition.
[On] : The AF lamp will light up in a low light
condition.
SETUP
Seoul
Tokyo
Seoul, Tokyo
2007/01/01 13:00
Set:OK
Set:OK
SETUP
World Time
Imprint
AF Lamp
Sound
USB
Off
On
Back:
Set:OK
[ Imprinting the recording date ]
[ Sound ]
■ There is an option to include DATE / TIME on still images.
■ If you set sound to ON, various sounds will be activated for camera startup,
when buttons are pressed, so that you can be aware of the camera operation
status.
● Sub menus
[Off]
: The DATE & TIME will not be
imprinted on the image file.
[Date]
: Only the DATE will be imprinted on
the image file.
[Date&Time] : The DATE & TIME will be imprinted
on the image file.
《64》
SETUP
Date&Time
World Time
Imprint
AF Lamp
Sound
Back:
Off
Date
Date&Time
Set:OK
● [Sound] sub menu : Off/ Low/ Medium/ High
SETUP
Imprint
AF Lamp
Sound
USB
LCD
Back:
Off
Low
Medium
High
Set:OK
Setup menu
[ Connecting an External Device (USB) ]
[ Selecting Video out type ]
■ You can select an external device to which you want to connect the camera
using the USB cable.
■ The Movie output signal from the camera can be NTSC or PAL.
Your choice of output will be governed by the type of device (monitor or TV, etc.)
to which the camera is connected. PAL mode can support only BDGHI.
● Sub menus
- [Computer] : Select this if you want to connect the
camera to your PC. Refer to page 77
for instructions on how to connect the
camera to your PC.
- [Printer] : Select this if you want to connect the
camera to your printer.
Refer to page 57 for instructions on
how to connect the camera to your
printer.
SETUP
AF Lamp
Sound
USB
LCD
Video Out
Computer
Printer
Back:
Set:OK
■ Connecting to an external monitor
In RECORDING/ PLAY mode, you can view the
stored still images or movie clips by connecting the
camera to an external monitor via the AV cable.
When the camera is connected to an external
monitor, the LCD monitor will be turned off
automatically.
SETUP
USB
LCD
Video Out
Quick View
Reset
Back:
NTSC
PAL
Set:OK
[ LCD brightness ]
■ You can adjust the LCD brightness.
● [LCD] sub menu : Dark, Normal, Bright
SETUP
Sound
USB
LCD
Video Out
Quick View
Back:
Dark
Normal
Bright
Yellow - Video
White - sound
Set:OK
《65》
Setup menu
- NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico.
[ Quick view ]
- PAL
■ If you enable Quick View before capturing an image, you can view the image
you just captured on the LCD monitor for the duration set in the [Quick View]
setup. Quick view is possible only with still images.
: Australia, Austria, Belgium, China, Denmark, Finland, Germany,
U.K., Holland, Italy, Kuwait, Malaysia, New Zealand, Singapore,
Spain, Sweden, Switzerland, Thailand, Norway.
- When using a TV as an external monitor, you will need to select the external or
AV channel of the TV.
- There will be a digital noise on the external monitor, but it is not a malfunction.
- If the image is not in the centre of the screen, use the TV controls to centre it.
● Sub menus
[Off]
: The quick view function can’t be
activated.
[0.5, 1, 3 sec] : The captured image is briefly
displayed during the selected time.
- When the camera is connected to an external monitor, the menu will be visible
on the external monitor and the menu functions are the same as those
indicated on the LCD monitor.
SETUP
USB
LCD
Video Out
Quick View
Reset
off
0.5 sec
1 sec
3 sec
Back:
Set:OK
[ Initialisation ]
■ All camera menu and function settings will be restored to their default values.
However, values for DATE/ TIME, LANGUAGE, and VIDEO OUT will not be
changed.
● Sub menus
[No] : Settings will not be restored to their
defaults.
[Yes] : All settings will be restored to their
defaults.
SETUP
USB
LCD
Video Out
Quick View
Reset
Back:
《66》
No
Yes
Set:OK
Setting up the Mycam menu
Start up sound
■ You can set up a start up image, start up sound and shutter sound. Every
camera working mode (with the exception of Voice recording mode) has the
MyCAM menu. The items indicated by
are default settings.
Menu tab
Main menu
Start Image
Start Sound
Shutter Sound
Sub menu
Off
User Image 1
Off
Sound 2
Off
Sound 2
Page
LOGO
User Image 2
Sound 1
Sound 3
Sound 1
Sound 3
p.67
■ You can select the sound that is activated whenever the camera is turned on.
● Start up sound : [Off], [Sound 1], [Sound 2],
[Sound 3]
- If the start up image is set to [Off], the start up
sound will not activate, even though you may
have set these to on.
MYCAM
Start Image
Start Sound
Shutter Sound
Off
Sound 1
Sound 2
Sound 3
Back:
Set:OK
p.67
p.67
※ Menus are subject to change without prior notice.
Start up image
Shutter sound
■ You can select the image that is first displayed on the LCD monitor whenever
the camera is turned on.
● Start up image : [Off], [LOGO], [User Image1],
[User Image2]
- Use a saved image for the start-up image with the
[User Image] in the [RESIZE] menu in the play mode.
- The start-up image will not be deleted by [DELETE]
or [Format] menu.
- The User images will be deleted by [Reset] menu.
MYCAM
Start Image
Start Sound
Shutter Sound
■ You can select the shutter sound.
● Shutter sound : [Off], [Sound 1], [Sound 2],
[Sound 3]
MYCAM
Start Image
Start Sound
Shutter Sound
Back:
Back:
Off
Sound 1
Sound 2
Sound 3
Set:OK
Set:OK
《67》
Important notes
Be sure to observe the following precautions!
■This unit contains precision electronic components. Do not use or store this unit
in the following locations.
- Areas exposed to severe changes in temperature and humidity.
- Areas exposed to dust and dirt.
- Areas exposed to direct sunlight or the inside of a vehicle in hot weather.
- Environments where there is high magnetism or excessive vibration.
- Areas with high explosives or highly flammable materials.
■Do not leave this camera in places subject to dust, chemicals (like naphthalene
and mothball), high temperature and high humidity.
Keep this camera with silica gel in a hermetically sealed box when not planning
to use the camera for a long period of time
■Sand can be particularly troublesome to cameras.
- Do not let sand get inside the camera when using it on beaches, coastal
dunes, or other areas where there is lots of sand.
- Doing so may result in failure or may permanently render the camera unusable.
■Handling the camera
- Never drop the camera or subject it to severe shocks or vibrations.
- Protect the large size LCD monitor from an impact. When this camera is not
used, keep it in the camera case.
- Avoid obstructing the lens or the flash when you capture an image.
- This camera is not waterproof.
To avoid dangerous electrical shocks, never hold or operate the camera with
wet hands.
- If you use this camera in wet places, such as beach or pool, do not let water or
sand get inside the camera. Doing so may result in failure or may permanently
damage the unit.
《68》
■ Extremes in temperature may cause problems.
- If the camera is transferred from a cold to a warm and humid environment,
condensation can form on the delicate electronic circuitry. If this occurs, turn
the camera off and wait for at least 1 hour until all moisture is dispersed.
Moisture built up can also occur on the memory card. If this happens, turn off
the camera and remove the memory card. Wait until the moisture has
dispersed.
■ Caution on Using the Lens
- If the lens is subjected to direct sunlight, it could result in the discoloration and
deterioration of the image sensor.
- Pay attention not to get fingerprints or foreign substances on the surface of the
lens.
■ If the digital camera is not used for a long period, an electric discharge can
occur.
It is a good idea to remove the battery and the memory card if you do not intend
using the camera for an extended period of time.
■ If the camera is exposed to an electronic interference, it will turn itself off to
protect the memory card.
Important notes
■ Camera Maintenance
- Use a soft brush (available from photo stores) to gently clean the lens and LCD
assemblies. If this does not work, lens-cleaning paper with lens cleaning fluid
can be used.
Clean the camera body with a soft cloth. Do not allow this camera to come into
contact with solvent materials such as benzol, insecticide, thinners etc. This
may damage the body shell of the camera and also affect its performance.
Rough handling can damage the LCD monitor. Take care to avoid damage
and keep the camera in its protective carry case at all times when not in use.
■ Do not attempt to disassemble or modify the camera.
■ Under certain conditions, static electricity can cause the flash unit to fire. This is
not harmful to the camera and is not a malfunction.
■ When images are uploaded or downloaded, the data transfer may be affected by
static electricity. In this case, disconnect and re-connect the USB cable before
trying the transfer again.
■ Before an important event or going on a trip, you should check the camera
condition.
- Take a picture for testing the camera condition and prepare extra battery.
- Samsung cannot be held responsible for camera malfunctions.
Warning indicator
■ There are several warnings that may appear on the LCD display
Memory Error!
ㆍMemory card error
→ Turn off the camera power and turn it on again
→ Insert the memory card again
→ Insert and format the memory card (p.63)
Card Locked!
ㆍThe memory card is locked
→ SD/SDHC memory card : Slide the write protect switch to the top of the
memory card
No Card!
ㆍA memory card is not inserted
→ Insert the memory card again
→ Turn off the camera power and turn it on again
No Image!
ㆍThere are no images stored on the memory
→ Take images
→ Insert a memory card that is holding some images
File Error!
ㆍFile error
→ Format the memory card
ㆍMemory card error
→ Contact a camera service centre
《69》
Warning indicator
Low Battery!
ㆍThere is low battery capacity
→ Insert fresh batteries.
Low Light!
ㆍWhen taking pictures in dark places
→ Take pictures in Flash Photography mode.
Before contacting a service centre
■ Please check the following
The camera doesn’t switch on
ㆍThere is low battery capacity
→ Insert fresh batteries. (p.10)
ㆍBattery is inserted incorrectly with the polarities reversed.
→ Insert the battery according to the polarity marks (+, -)
ㆍBattery is not inserted
→ Insert the battery and turn on the camera
The camera power ceases while in use
ㆍThe battery is exhausted
→ Insert fresh batteries
ㆍThe Camera is turned off automatically
→ Turn on the camera power again.
《70》
Battery power quickly drains
ㆍThe Camera is being used in low temperatures
→ Keep the camera in warm conditions (i.e. inside a coat or jacket) and only
remove it in order to take images
Camera does not take images when pressing the Shutter button
ㆍThere is insufficient memory capacity
→ Delete unnecessary image files
ㆍThe memory card has not been formatted
→ Format the memory card (p.63)
ㆍThe memory card is exhausted
→ Insert a new memory card
ㆍThe memory card is locked
→ Refer to [Card Locked!] error message (p.69)
ㆍThe camera’s power is off
→ Turn the camera power on
ㆍThe battery is exhausted
→ Insert fresh batteries. (p.10).
ㆍBattery is inserted incorrectly with the polarities reversed.
→ Insert the battery according to the polarity marks (+, -)
The camera suddenly stops working while in use
ㆍThe camera stopped due to a malfunction
→ Remove /re-insert battery and switch the camera on
Before contacting a service centre
The images are unclear
ㆍA picture was taken the subject without setting an appropriate macro mode
→ Select an appropriate macro mode to take a clear image.
ㆍTaking a picture beyond the flash range
→ Take a picture within the flash range
ㆍThe lens is smudged or dirty
→ Clean the lens
Colour of image is different to the original scene
ㆍWhite balance or effect setting is incorrect
→ Select appropriate White balance and effect
The flash does not fire
ㆍFlash off mode has been selected
→ Dis-engage flash off mode
ㆍThe camera mode can’t use the flash
→ Refer to the FLASH instruction (p.24)
No image on external monitor
ㆍThe external monitor has not been connected properly with the camera
→ Check the connection cables
ㆍThere are incorrect files in the memory card
→ Insert a memory card that has correct files
Incorrect date and time is displayed
ㆍThe date and time have been set incorrectly or the camera has adopted the
default settings
→Reset the date and time correctly
When using the PC’s explorer, the [Removable Disk] file does not show
ㆍCable connection is incorrect
→ Check the connection
ㆍThe camera is off
→ Turn the camera on
ㆍThe operating system is not Windows 98, 98SE, 2000, ME, XP/ Mac OS 10.0 10.3. Alternatively the PC does not support USB
→ Install Windows 98, 98SE, 2000, ME, XP/ Mac OS 10.0 - 10.3 to PC that
supports USB
ㆍThe camera driver is not installed
→ Install a [USB Storage Driver]
The camera buttons do not operate
ㆍCamera malfunction
→ Remove/re-insert battery and switch the camera on
A card error has occurred while the memory card is in the camera.
ㆍIncorrect memory card format
→ Re-format the memory card
Images are too bright
ㆍExposure is excessive
→ Reset exposure compensation
The images don't play back
ㆍIncorrect file name (Violation of DCF format)
→ Do not change the image file name
《71》
Specifications
■ Image Sensor
- Type : 1/1.8" CCD
- Effective Pixel : Approx. 8.1Mega-pixel
- Total Pixel : Approx. 8.3Mega-pixel
■ Lens
- Focal Length : SHD f = 7.8 ~ 39mm (35mm film equivalent : 38 ~ 190mm)
- F No. : F2.8 ~ 4.4
- Digital Zoom :·Still Image mode : 1.0X ~ 5.0X
·Play mode : 1.0X ~ 12.0X (depends on image size)
■ LCD Monitor : 2.5" color TFT LCD (230,000 dots)
■ Focusing
- Type : TTL auto focus, AF Assist Lamp, Manual focus, Multi Point AF
- Range
Normal
Wide
Tele
Wide
Tele
80cm ~ infinity
Super Macro
1 ~ 10cm
-
■ Shutter
- Speed : Auto : 1 ~ 1/2,000 sec.
M, S Mode : 15 ~ 1/2,000 sec.
Night : 15 ~ 1/2,000 sec.
Fireworks : 4 sec.
《72》
Macro
10 ~ 80cm
50 ~ 80cm
Auto Mode
10cm ~ infinity
50cm ~ infinity
Manual Focus
1cm ~ infinity
50cm ~ infinity
■ Exposure
- Control : Program AE, Shutter Priority AE, Aperture Priority AE or Manual
Exposure
- Metering : Multi, Spot
- Compensation : ±2EV (1/2EV steps)
- ISO Equivalent : Auto, 50, 100, 200, 400, 800, 1600
■ Flash
- Modes : Auto, Auto & Red-eye reduction, Fill-in flash, Slow sync, Flash off
- Range : Wide : 0.2m ~ 3.0m
Tele : 0.5m ~ 2.5m (ISO AUTO)
- Recharging Time : Approx. 5 sec.
■ Sharpness : Soft, Normal, Vivid
■ Effect : Color(Normal, B/W, Sepia, Negative, Red, Green, Blue)
Composite, Highlight, Frame
■ White Balance : Auto, Daylight, Cloudy, Fluorescent_H, Fluorescent_L,
Tungsten, Custom
■ Voice Recording : Voice Recording (max. 1hour)
Voice Memo in Still Image (max. 10 sec.)
■ Date Imprinting : Date, Date&Time, Off (user selectable)
■ Shooting
- Still Image:·Modes : Auto, Program, A, S, M, ASR, Scene
·Scene : Night, Portrait, Children, Landscape, Close-up, Text,
Sunset, Dawn, Backlight, Fireworks, Beach & Snow
·Continuous : Single, Continuous, Motion Capture, AEB,
Interval Shooting
·Self-timer : 10 sec., 2 sec., Double(10sec., 2sec.)
Specifications
- Movie Clip :·With Audio (recording time : memory capacity dependent)
·Size: 800x592, 720x480, 640x480, 320x240
·Frame rate : 30 fps, 20 fps, 15 fps
(15/20 fps for 800x592, 720x480)
·Stabilizer
·Optical Zoom : up to 5.0X
■ Storage
- Media :·Internal about 20MB
·External memory : SD / MMC/ SDHC (up to 4GB guaranteed)
- File Format :·Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.0
·Movie Clip : AVI (MPEG-4)
·Audio : WAV
- Image Size
·Normal Shooting Mode
8M
5M
3M
1M
3264X2448
2592X1944
2048X1536
1024X768
6M
Wide angle
Print angle
3264X1824
7MP
6MW
■ Power Source
- Primary Battery : 2x AA Alkaline
- Rechargeable battery(Optional) : SNB-2512 KIT or SNB-2512B KIT
(2xAA Ni-MH Battery & Charger)
※ Included battery may vary depending on sales region.
■ Dimensions (WxHxD) : 104 x 63.6 x 24.8 mm (excluding protrusion)
■ Weight : 172g (without batteries and card)
7M
3264X2176
■ Operating Temperature : 0 ~ 40°C
■ Operating Humidity : 5 ~ 85%
- Internal Capacity (256MB MMC(Multi Media Card))
8M
■ Image Play
- Type : Single image, Thumbnails, Slide show, Movie Clip
- Editing : Trimming, Resizing, Rotate, Color Effect
■ Interface
- Digital output connector : USB 2.0(High Speed)
- Audio : Mono
- Video output : NTSC, PAL (user selectable)
- DC power input connector : 3.3V
5M
3M
1M
Super Fine
57
68
84
93
172
558
Fine
103
115
134
158
265
663
Normal
180
206
233
271
425
742
■ Software
- Camera Driver : Storage Driver (98/98SE/2000/ME/XP, Mac OS 10.0 ~ 10.3)
- Application : Digimax Master
※ Specifications are subject to change without prior notice.
※ All trademarks are the property of their respective owners.
※ These figures are measured under Samsung’s standard conditions and may
vary depending on shooting conditions and camera settings.
《73》
Software Notes
About the software
Please ensure that you read the instruction manual carefully before use.
•The attached software is a camera driver and image editing software tool for
Windows.
•Under no circumstances should all or part of either the software or the user
manual be reproduced.
•Copyrights for software are licensed only for use with a camera.
•In the unlikely event of a manufacturing fault, we will repair or exchange your
camera.
We cannot, however, be held responsible in any way for damage caused by
inappropriate use.
•Using a Hand-made PC or a PC and OS that has not been guaranteed by the
manufacturer is not covered by the Samsung warranty.
•Before reading this manual, you should have a basic knowledge of computers
and O/S (Operating Systems).
System Requirements
For Windows
PC with processor better than Pentium II 450MHz
(Pentium 700MHz recommended)
Before connecting the camera to the PC, you
should first install the camera driver.
※Screen Captures illustrated on this manual is
based on English Edition of Windows.
■ Camera driver : This enables images to transfer between the camera and PC.
This camera uses the USB Storage Driver as the camera driver. You can use the
camera as a USB card reader. After installing the driver and connecting this
camera to the PC, you can find [Removable Disk] in [Windows Explorer] or [My
computer]. A USB Storage Driver is provided only for Windows. A USB Driver for
MAC is not included with the Application CD. You can use the camera with Mac
OS 10.0 ~ 10.3.
For Macintosh
Power Mac G3 or later
Windows 98 / 98SE / 2000 / ME / XP
Mac OS 10.0 ~ 10.3
Minimum 64MB RAM
Minimum 64MB RAM
200MB of available hard disk space
110MB of available hard-disk space
USB port
USB port
CD-ROM drive
CD-ROM drive
1024x768 pixels, 16bit color display
compatible monitor
(24bit color display recommended)
For playing back a movie clip
Mac OS 10.1 or later
MPlayer
《74》
After inserting the CD-ROM provided with this camera into the CD-ROM drive, the
following window should automatically run.
■ Digimax Master : This is the all-in-one multi media software solution.
You can download, view, edit and save your digital images and movie clips clip
with this software. This software is only compatible with Windows.
INFORMATION
● Be sure to check the system requirements before installing the driver.
● You should allow 5 ~ 10 seconds for running the automatic setup program
according to the capability of your computer. If the frame does not show, run
the [Windows Explorer] and select [Installer.exe] in the CD-ROM Drive
root directory.
Setting up the application software
■ To use this camera with a PC, install the application software first.
After this has been done, the stored images in the camera can be moved to the
PC and can be edited by an image editing program.
■ You can visit the Samsung web-site through the internet.
http://www.samsungcamera.com : English
http://www.samsungcamera.co.kr : Korean
1. The auto run frame will display.
Click the [Install] menu in the Auto run
frame.
2. Install the camera driver, DirectX, Xvid and Digimax Master by selecting a
button shown on the monitor. If an upper version of DirectX was installed on
your computer, DirectX may not be installed.
※ The XviD codec is distributed according to and under the terms and conditions of
the GNU General Public License and everyone can copy, modifiy and distribute
this codec freely, but WITHOUT ANY WARRANTY, IMPLIED OR
EXPRESSED, OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE; provided, however, that you have to follow the GNU General Public
License whenever you are distributing this codec or modification thereof.
For more information see the GNU General Publice License documents
(http://www.gnu.org/copyleft/gpl.html).
《75》
Setting up the application software
3. After restarting the computer, connect the PC to the camera with the USB
cable.
4. Turn the camera power on.
The [Found New Hardware Wizard] will
open and the computer will recognise the
camera.
※ If your OS is Windows XP, an image
viewer program will open.
If the download window of Digmax Master
opens after starting Digimax Master, the
camera driver was set up successfully.
INFORMATION
● If you have installed the camera driver, the [Found New Hardware Wizard]
may not open.
● On a Windows 98 or 98 SE system, the Found New Hardware Wizard
dialog box opens and a window asking you to select a driver file may
appear. In this case, specify "USB Driver" in the CD supplied. (for Windows
98 and 98 SE).
《76》
Starting PC mode
•If you connect the USB cable to a USB port on your PC and then turn on the
power, the camera will automatically switch to "computer connection mode".
•In this mode, you can download stored images to your PC through the USB
cable.
•The LCD monitor is always turned off in PC mode.
■ Connecting the camera to a PC
1. In any mode with the exception of Voice Recording
mode, press the Menu button.
2. Press the LEFT/ RIGHT button and select the
[SETUP] menu tab.
3. Select the [USB] menu by pressing the UP/ DOWN
button and press the RIGHT button.
4. Use the UP and DOWN buttons to select
[Computer], and then press the OK button.
5. Press the menu button twice and the menu will
disappear.
6. Connect the PC to the camera with the USB cable.
■ Connecting the camera to a PC
SETUP
AF Lamp
Sound
USB
LCD
Video Out
Back:
Computer
Printer
Set:OK
※If you selected [Printer] in Step 4, when you connect the camera to your
printer, the [Connecting Printer] message will display and the connection will
not be established.
In this case, disconnect the USB cable, and then follow the procedure from
Step 2 and onward.
■ Disconnecting the camera and PC : Refer to page 79
(Removing the removable disk).
INFORMATION
● Before inserting cables, check the directions and do not insert by force. It
may cause breakage of cable or camera.
《77》
Starting PC mode
■ Downloading stored images
You can download the still images stored on the camera to your PC's hard disk
and print them or use a photo editing software to edit them.
6. Press the right mouse button and a pop-up
menu will open. Click [Paste].
1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display, select
[My computer] and double click [Removable
Disk → DCIM → 100SSCAM].
The image files will then be displayed.
7. An image file is transferred from the camera
to your PC.
3. Select an image and press the right
mouse button.
- By using [Digimax Master], you can see the stored images in the memory
directly on the PC monitor and you can copy or move the image files.
4. A pop-up menu will open.
Click the [Cut] or [Copy] menu.
- [Cut] : cuts a selected file.
- [Copy] : copies files.
5. Click a folder where you want to paste the file.
《78》
CAUTION
● We recommend that you should copy the images to the PC to view them.
Opening images directly from the removable disk may be subject to
unexpected disconnection.
● When you upload a file that is not taken by this camera to the Removable
Disk, the [File Error!] message will be displayed on the LCD monitor in the
PLAY mode, and nothing is displayed in THUMBNAIL mode.
Removing the removable disk
■ Windows 98/98SE
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has finished
blinking and is constantly on.
2. Unplug the USB cable.
■ Windows 2000/ME/XP
(The illustrations may differ from those shown depending on the Windows O/S.)
1. Check whether the camera and PC are transferring a file.
If the camera status lamp blinks, please wait until the lamp has finished
blinking and is constantly on.
5. A [Safe to Remove Hardware] window will
open. Click the [OK] button.
6. A [Unplug or Eject Hardware] window will
open. Click the [Close] button and the
removable disk will be removed safely.
7. Unplug the USB cable.
2. Double-click the [Unplug or Eject Hardware]
icon on the task bar.
[Double-click!]
3. The [Unplug or Eject Hardware] window will
open. Select the [USB Mass Storage Device]
and click the [Stop] button.
4. The [Stop a Hardware device] window will open.
Select the [USB Mass Storage Device] and click
the [OK] button.
《79》
Setting up the USB Driver for MAC
1. A USB Driver for MAC is not included with the software CD as MAC OS
supports the camera driver.
2. Check the MAC OS version during start-up.
This camera is compatible with MAC OS 10.0 ~ 10.3.
3. Connect the camera to the Macintosh and turn the camera power on.
4. A new icon will be displayed on the desktop after connecting the camera to
the MAC.
Removing the USB Driver for Windows 98SE
■ To remove the USB driver, refer to the process shown below.
1. Connect the camera to your PC and turn them on.
2. Check whether the Removable Disk is on the [My Computer].
3. Remove the [Samsung Digital Camera] on the Device manager.
Using the USB Driver for MAC
1. Double click a new icon on the desktop and the folder in the memory will be
displayed.
2. Select an image file and copy or move it to MAC.
4. Disconnect the USB cable.
5. Remove the [Samsung USB Driver] on the Add/Remove Programs
Properties.
CAUTION
● For Mac OS 10.0 or later : First complete uploading from computer to
camera and then remove the removable disk
with the Extract command.
●If a movie clip can’t play back on the Mac OS, please visit the following
site(http://www.divx.com/divx/mac/) and download the codec. Or, use a
media player that supports the Xvid codec (Mplayer).
6. Uninstallation is complete.
《80》
Digimax Master
■ You can download, view, edit and save your images and movies with this
software. This software is only compatible with Windows except for
the Windows 98.
■ To start the program, click [Start → Programs → Samsung → Digimax Master
→ Digimax Master].
● Downloading images
1. Connect the camera to your PC.
2. A window for downloading images will
display after connecting the camera to your
PC.
- To download the captured images, select
the [Select All] button.
- Select desired folder in the window and
click the [Select All] button. You can save
captured images and selected folder.
- If you click the [Cancel] button, downloading will be
cancelled.
4. Select a destination and make a folder to
save downloaded images and folders.
- Folder names can be made in order of date
and images will be downloaded.
- Folder name will be made as you want and
images will be downloaded.
- After selecting a folder that was made
before, images will be downloaded.
5. Click [Next >] button.
6. A window will open as shown alongside.
The destination of the selected folder will be
displayed on the upper side of the window.
Click the [Start] button to download the
images.
3. Click [Next >] button.
7. Downloaded images will be displayed.
《81》
Digimax Master
● Image viewer : You can view the stored images.
①
● Image edit : You can edit the still image.
⑤
⑥
①
④
⑦
②
③
④
②
③
- Image viewer functions are listed below.
① Menu bar : You can select menus.
File, Edit, View, Tools, Change functions, Auto download, help, etc.
② Image selection window : You can select the desired images in this window.
③ Media type selection menu : You can select image viewer, image edit and
movie edit functions in this menu.
④ Preview window : You can preview an image or a movie clip and check the
multi media information.
⑤ Zoom bar : You can change preview size.
⑥ Folder display window : You can see the folder location of the selected
image.
⑦ Image display window : Images of the selected folder are displayed.
※ Refer to the [Help] menu in Digimax Master for further information.
《82》
- Image edit functions are listed below.
① Edit menu : You can select the following menus.
[Tools] : You can resize or crop the selected image. See the [Help] menu.
[Adjust] : You can modify image quality. See the [Help] menu.
[Retouch] : You can change image or insert effects on the image. See the
[Help] menu.
② Drawing tools : Tools for editing an image.
③ Image display window : A selected image displays in this window.
④ Preview window : You can preview the changed image.
※ A still image edited with Digimax Master can’t be played back on the camera.
※ Refer to the [Help] menu in Digimax Master for further information.
Digimax Master
FAQ
FAQ
● Movie edit : You can get the still image, movie clip, narration, music files together
in a movie clip.
■ Please check the following if the USB connection malfunctions.
Case 1
USB cable is not connected or it is not the supplied USB cable.
→ Connect the supplied USB cable.
Case 2
The camera is not recognised by your PC.
Sometimes, the camera may appear under [Unknown Devices] in
Device Manager.
→ Install the camera driver correctly.
Turn off the camera, remove the USB cable, plug in the USB cable
again, and then turn on the camera.
Case 3
There is an unexpected error during file transfer.
→ Turn the camera power off and on again. Transfer the file again.
Case 4
When using the USB hub.
→ There may be a problem in connecting the camera to the PC through
the USB hub if the PC and the hub are not compatible. Wherever
possible, connect the camera to the PC directly.
Case 5
Are other USB cables connected to the PC?
→ The camera may malfunction when it is connected to the PC at the
same time as another USB cable. In this case, disconnect the other
USB cable, and connect only one USB cable to the camera.
①
②
- Movie clip edit functions are listed below.
① Edit menu : You can select the following menus.
[Add Media] : You can add other media elements to a movie.
[Edit Clip] : You can change the brightness, contrast, colour and saturation.
[Effects]
: You can insert an effect.
[Set Text] : You can insert texts.
[Narrate] : You can insert a narration.
[Produce] : You can save the edited multi media as a new file name.
You can select AVI, Windows media (wmv), Windows media
(asf) and movie clip for this camera (avi, MPEG-4) file types.
② Frame display window : You can insert multi media in this window.
※ Some movie clips that were compressed with a codec that is not compatible with
the Digimax Master can’t play back in the Digimax Master.
※ Refer to the [Help] menu in Digimax Master for further information.
《83》
FAQ
Case 6
When I open the Device Manager (by clicking Start → (Settings) →
Control Panel → (Performance and Maintenance) → System →
(Hardware) → Device Manager), there are Unknown Devices or Other
Devices entries with a yellow question mark(?) beside them or devices
with an exclamation mark(!) beside them.
→ Right-click on the entry with the question (?) or exclamation (!) mark
and select "Remove". Restart the PC and connect the camera again.
For Windows 98 PC, remove the camera driver also, restart the PC,
and then reinstall the camera driver.
Case 7
In some security programs (Norton Anti Virus, V3, etc.), the computer
may not recognise the camera as a removable disk.
→ Stop the security programs and connect the camera to the computer.
Refer to the security program instructions about how to temporarily
disable the program.
Case 8
The camera is connected to the USB port located on the front of the
computer.
→ When the camera is connected to the USB port located on the front of
the computer, the computer may not recognise the camera. Connect
the camera to the USB port located on the back of the computer.
《84》
■ When the movie clip doesn’t play back on the PC
※ When the movie clip recorded by the camera doesn’t play back on the PC,
the causes are mostly due to the codec installed on the PC.
● When codec for play back the movie clip isn’t installed
→ Install the codec as listed below.
[ Installing codec for Windows ]
1) Insert the CD provided with the camera.
2) Run the windows explorer and select [CD-ROM drive:\XviD] folder and
click the XviD-1.1.0-30122005.exe file.
※ The XviD codec is distributed according to the GNU General Public License
and everyone can copy, distribute and change this codec. This License
applies to any program or other work which contains a notice placed by the
copyright holder saying it may be distributed under the terms of this General
Public License.
For more information, see the License documents
(http://www.gnu.org/copyleft/gpl.html).
[ Installing codec for Mac OS ]
1) Visit the following site for downloading the codec.
(http://www.divx.com/divx/mac)
2) Click the [Free Download] button located at the upper right side of the page
and a window for downloading the DivX codec will display.
3) Select Mac OS you use and click the [Download] button. Save it on a folder
you want to.
4) Run the downloaded file and the codec for playing back the movie clip will
be installed.
※ If a movie clip can’t play back on the Mac OS, use a media player that
supports XviD codec (Mplayer).
FAQ
● When the DirectX 9.0 or later is not installed
→ Install the DirectX 9.0 or later
1) Insert the CD provided with the camera
2) Run the windows explorer and select the [CD-ROM drive:\ USB
Driver\DirectX 9.0] folder and click the DXSETUP.exe file.
The DirectX will be installed. Visit the following site for downloading the
DirectX.http://www.microsoft.com/directx
● If a PC (Windows 98) stops responding while the camera and PC are connected
repeatedly
→ If a PC (Windows 98) is turned on for a long time and the camera is
connected repeatedly, the PC may not recognise the camera. In this case, restart the PC.
Correct Disposal of This Product
Correct Disposal of This Product (Waste Electrical & Electronic
Equipment)
(Applicable in the European Union and other European countries with
separate collection systems) This marking shown on the product or its
literature, indicates that it should not be disposed with other household
wastes at the end of its working life.
To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources. Household
users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for
environmentally safe recycling. Business users should contact their supplier and
check the terms and conditions of the purchase contract.
This product should not be mixed with other commercial wastes for disposal.
● If a PC connected with the camera stops responding while Windows is starting.
→ In this case, disconnect the PC and the camera and Windows will start.
If the problem happens continuously, set the Legacy USB Support to disable
and re-start the PC. The Legacy USB Support is in the BIOS setup menu.
(The BIOS setup menu differs from the PC manufacturers and some BIOS
menus don’t have Legacy USB Support) If you can’t change the menu by
yourself, contact to the PC manufacturer or BIOS manufacturer.
● If the movie clip can’t be deleted, removable disk can’t be extracted or an error
message displays during the file transfer.
→ If you install only the Digimax Master, the problems mentioned above
occasionally happen.
- Close the Digimax Master program by clicking the Digimax Master icon on
the Taskbar.
- Install all the application programs included in the software CD.
(You must install the Movie clip codec)
Samsung Techwin cares for the environment at all product
manufacturing stages to preserve the environment, and is
taking a number of steps to provide customers with more
environment-friendly products. The Eco mark represents
Samsung Techwin's will to create environment-friendly
products, and indicates that the product satisfies the EU
RoHS Directive.
《85》
FCC notice
■ NOTE :
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to pro-vide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and,
if not in-stalled and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
■ CAUTION :
Changes or modifications not expressly approved by the manufacturer
responsible for compliance could void the user’s authority to operate the
equipment.
■ Declaration of Conformity
Trade Name
: SAMSUNG TECHWIN
Model No.
: Digimax S850
Responsible Party : Samsung Opto-Electronics America, INC.
Address
: 40 Seaview Dr. Secaucus,NJ 07094
Telephone No.
: 201-902-0347
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
《86》
MEMO
MEMO
MEMO
《87》
MEMO
《88》
MEMO
SAMSUNG TECHWIN CO., LTD.
SAMSUNG FRANCE S.A.S.
SAMSUNG OPTO-ELECTRONICS UK LIMITED
OPTICS & DIGITAL IMAGING DIVISION
145-3, SANGDAEWON 1-DONG, JUNGWONGU,
SUNGNAM-CITY, KYUNGKI-DO, KOREA
462-121
TEL : (82) 31-740-8086, 8088, 8090, 8092, 8099
FAX : (82) 31-740-8398
www.samsungcamera.com
BP 51 TOUR MAINE MONTPARNASSE 33,
AV .DU MAINE 75755, PARIS CEDEX 15, FRANCE
HOTLINE PHOTO NUMÉRIQUE :
00 800 22 26 37 27(Numéro Vert-Appel Gratuit)
TEL : (33) 1-4279-2200
FAX : (33) 1-4320-4510
www.samsungphoto.fr
SAMSUNG HOUSE 1000 HILLSWOOD DRIVE
HILLSWOOD BUSINESS PARK
CHERTSEY KT16 OPS U.K.
TEL : 00800 12263727
(free for calls from UK only)
UK Service Hotline : 01932455320
www.samsungcamera.co.uk
SAMSUNG OPTO-ELECTRONICS AMERICA, INC.
SAMSUNG OPTO-ELECTRONICS GMBH
HEADQUARTERS
40 SEAVIEW DRIVE, SECAUCUS,
NJ07094, U.S.A.
TEL : (1) 201-902-0347
FAX : (1) 201-902-9342
WESTERN REGIONAL OFFICE
18600 BROADWICK ST.,
RANCHO DOMINGUEZ, CA 90220, U.S.A.
TEL : (1) 310-900-5284/5285
FAX : (1) 310-537-1566
www.samsungcamerausa.com
AM KRONBERGER HANG 6
D-65824 SCHWALBACH/TS., GERMANY
TEL : 49 (0) 6196 66 53 03
FAX : 49 (0) 6196 66 53 66
www.samsungcamera.de
RUSSIA INFORMATION CENTER
SAMSUNG ELECTRONICS
117545 ST. DOROZHNAYA BUILDING 3,
KORPUS 6, ENTRANCE 2, MOSCOW, RUSSIA
TEL : (7) 495-363-1700
CALL FREE : (8) 800 200 0 400 (from Russia only)
www.samsungcamera.ru
TIANJIN SAMSUNG OPTO-ELECTRONICS CO., LTD
No.9 zhangheng Street. Micro-Electronic
Industrial Park Jingang Road Tianjin China.
POST CODE : 300385
TEL : (86) 22-2761-4599
FAX : (86) 22-2769-7558
www.samsungcamera.com.cn
Internet address - http : //www.samsungcamera.com
The CE Mark is a Directive conformity
mark of the European Community (EC)
6806-3601
Download PDF